REMOTE CONTROL BASICS BATTERY REPLACEMENT:
1.Remove the battery holder as the direction indicated by the arrow.
2.Replace the battery Set a new battery property with (+)side up.
3.Insert the battery holder. Push in the holder to the original position.
LEGACY
NOTE ON BATTERIES:
Old batteries must immediately be removed and disposed.
LCD89DFX
BATTERY INFORMATION:
Designated Battery: CR 2025 3V
Battery Life: 6 months with normal use (in normal room temperatur)
INSTRUCTION MANUAL
CAUTION:
Improper use of batteries may cause overheating, explosion or ignition. Resulting in
jury or fire .Battery leakage may cause damage to the unit.
Do not disassemble or short the batteries. Do not throw the batteries into the fire.
To avoid the risk of accident, keep the batteries out of reach of children.
1. LOCAL/DISTANCE BUTTON
If you findthe receiving signal is weak andthere is the
word LOC displayed on LCD whenyou tune fordistance
station, firstly press the button todisappear the word
LOC on LCD, then tune againfor the distancestation.
If you findthe interference to the receiving signal is very
strong and there is not theword LOC displayed on LCD
when you tunefor local station, firstly press the button to
display the word LOC on LCD, then tune again for the local
station.
2. LOUDNESS BUTTON
Press it to enhance the basssound effect immediately
when the volumelevel is reduced to below halflevel.
AUTO-LOADING COMPACT DISC PLAYER
AND AM/FM-STEREO DIGITAL PLL TUNING RADIO
ANTI-THEFT FLIP DOWN DETACHABLE FRONT PANEL
WITH INFRA-RED REMOTE CONTROLLER
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC PLAY:
LOCATION AND FUNCTION OF CONTROLS
Cleaning discs
Before playing, clean the disc with a clean, lint-free cloth.
Wipe the disc in the direction of the arrow.
NOTE:
. Do not use so solvents such as benzine, thinners. Commercially available
cleaners or anti static spray damage the unit.
Insert a disc with the label surface down. Doing so may damage the unit.
Label
surface up
1. V-SEL/MENU/(SEL) AND V-UP/DN, MENU-UP/DN(+/-) BUTTONS
1).Press SEL button shortly and repeatedly to select sound mode VOLUME,
BASS(without preset DSP), TREBLE(without preset DSP), BALANCE and
FADER, then press + or - button to adjust level of the selected sound mode.
NOTE:
. Do not try to insert another disc when one has been already inserted.
Doing so may damage the unit.
.Handle the disc by its edge. And to keep the disc clean, do not touch
2).Press SEL button hold for more than 1 second to turn on MENU mode,
and the LCD will display DSP OFF/POP M/ROCK M/CLASS M/FLAT M,
then press SEL button shortly and repeatedly to select BEEP ON/BEEP
OFF, SEEK1/SEEK2, VOL LAST/VOL ADJ(When it is in VOL ADJUST mode,
the next mode will be A-VOL after VOL ADJUST mode, then you can adjust
the volume level) in the sequence and circulation. After select the desired
MENU mode, press + or - button to select the mode of the selected MENU.
the surface.
2. OPEN BUTTON
.Do not stick paper or tape on the disc.
Press it to flip down the front panel and you can insert the disc
into the CD compartment or press the EJ button to eject the disc
from the disc compartment or take away the front panel.
.Do not expose the disc to direct sunlight or heat sources such as hot air
ducts. Or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.
3. LCD (LIQUID CRYSTAL DISPLAY)
TROUBLE SHOOTING
To solve the common problem, read the trouble shooting list. If you still can
not solve the problem, consult your nearest service dealer.
4. UP AND DN BUTTONS
1)In RADIO mode, press ^ or v button shortly and repeatedly to
manually tune up or down for the desired radio station with step by
step. Press ^ or v button hold for more than 0.5 seconds to
auto-matically tune up or down for the radio station of strong signal.
2)In CD mode, press ^ button to play next track. Press v button
once to play the current track from the beginning of the current
track, press v button twice continuously to play the last track.
Press ^ or v button hold to skip forward or backward.
Symptom
No power
Cause
Solution
The car ignition is not on.
If the power supply is properly
connected to the car accessory
switch the ignition key to " ACC "
The fuse is blown
Replace the fuse
Disc cannot
be loaded
Presence of CD disc inside
the player
Remove the disc in the player
then put a new upward
5. AUTO-STORAGE/PRESET MEMORY SCAN BUTTON
Inserting the disc in upside
down
Insert the compact disc with
the label facing upward
Disc cannot
be read
In radio mode, press it to perform all stations memory for 5 seconds
each time, while memory digital and frequency will flash on LCD. If
the button is pressed for more than 2 seconds, it will seek station
on current band, then write to the preset memories. When the
auto-storage operation is completed, it will automatically perform
for 5 seconds each time. During the memory station performing,
press 1-6 digital buttons to select and stop scanning function.
Compact disc is extremely
dirty or defective
Clean the disc or try to play a
new one
Temperature inside the
car is too high
Cool off until the ambient
temperature returns to normal
Volume is in minimum
Adjust volume to a desired level
Check wiring connection
Wiring is not properly
connected
No sound
1.The built-in microcomputer
is not operating properly
due to noise
2.Front panel is not properly
fix into its place
6. BAND BUTTON
Press it repeatedly to select your desired radio band during RADIO
mode.
1. Press the RESET button
2. Reinstall the front panel
The operation
keys do not
work
7. CLOCK BUTTON
The installation angle
is more than 30 degrees
Adjust the installation angle
to less than 30 degrees
Sound skips
Press CLK button to display time on LCD, then press CLK button
hold until time flashes on LCD, thirdly press + or - button to adjust
HOUR or MINUTE.
The disc is extremely
dirty or defective
Clean the compact disc/try to
play a new one
The radio does
not work
the radio
8. SCAN BUTTON
Insert the antenna cable firmly
select a station manually
The antenna cable is not
connected
the signals are too weak
Press it to scan up by one channel step with station detection. If a
valid signal has detected, the current frequency is blinked within 5
seconds, then press it again to stop scan and remain the current
frequency; otherwise, the unit continue to scan up by one channel
step with station detection 5 seconds later.
station
automatic
selection does
not work
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9. POWER BUTTON
SPEAKER CONNECTION
Press any button except the EJECT and OPEN button to turn on the
unit, press PWR button hold for more than 0.5 seconds to turn off
the unit.(After switching on the ACC POWER first time for 3 seconds,
can only turn on the unit)
ANTENNA PLUG
YELLOW
7 A
AUX LINE IN
RED R
MEMORY B+
FUSE
10.STEREO/MONO BUTTON
Press it repeatedly to select STEREO or MONO sound mode.
WHITE L
BLACK(GND)
RED (B+)
0.5 A
FUSE
RCA LINE OUT
GRAY
RED R
WHITE L
FRONT
BLUE AUTO ANT
+
+
11.MUTE BUTTON
WHITE
FRONT
Press the button to eliminate or resume the sound immediately.
To resume the sound immediately, can also press MODE, BAND, +,
-, (LOUD) and SEL button.
RIGHT
SP
WHITE/BLACK
GREEN
GRAY/BLACK
VIOLET
LEFT
SP
+
+
REAR
REAR
GREEN/BLACK
VIOLET/BLACK
12. PRESET STATION [ 1-6 ] AND TOP/CDP, INT, RPT, RDM BUTTONS.
A].To memorize the current frequency, press any one of the six
preset buttons hold for more than 2 seconds.
NOTE:
1. In spite of having any kinds of speaker system, must use 4 ohms
impedance of speaker to reduce the distortion during high volume level.
2. Prohibit to make the conductors of auto antenna and ground
touch with each other.
B].To recall the preset memory, press one of the preset buttons
[1-6].
C).In CDP mode, press TOP/CDP button to pause CDP playback,
press it again to resume CDP playback. Press it hold for more
than about 0.5 seconds to play the first track of the disc.
D).In CDP mode, press INT button to play the first 10 seconds part
of each track, press it again to stop INT mode and retain playing
the track currently selected.
E).In CDP mode, press RPT button to play the current track
repeatedly. Press it again to cancel this mode.
F).In CDP mode, press RDM button to play the track in random
order. Press it again to cancel this mode.
USA
EUROPE
IMPORTANT:
This radio is set to USA frequency by factory, if European
frequency is required please flip the frequency step switch on
the side of the unit.
13. MODE BUTTON
Press it to select RADIO or CDP mode.
After the switchover of the frequency switch, the frequency convert
function will not be valid until the RESET button has been pressed.
(The RESET button is in the rear facet of the front panel)
14. INFRA-RED REMOTE CONTROLLING SENSOR
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CAUTION: Do not install the detachable panel before connecting the wire.
1. The unit is designed for negative terminal of the battery which is connected to the
vehicle metal. Please confirm it before installation.
2. If the car interior is extremely hot, as after being parked in the sun, do not use
the player until the car has been driven for a while to cool off the interior.
3. Press the OPEN button to flip down the front panel (see fig.1), then take away the
front panel (see fig.2) and put it in the protective case (see fig.3) safe keeping.
4. Install the front panel back into its bracket and then push it back to the position for
playing (see fig.4).
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|