Operating Manual
KODAK
CAROUSEL®
Slide Projector
CONSUMER IMAGING
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual
KODAK
CAROUSEL
Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Editing Your Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
How to Obtain Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Serial Number
The serial number of your projector is printed on the label affixed to the power
cord retainer on the base of the projector. Record this number, as well as the
model identification, date, and place of purchase, for future reference.
KODAK CAROUSEL® Slide Projector
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Congratulations!
You have just purchased a KODAK CAROUSEL Slide Projector which:
• triples lamp life
• provides brighter and more vivid colors!
Introduction
Take the time to read the instructions in this operating manual to become
familiar with your KODAK CAROUSEL® Slide Projector and how to operate
it properly.
2
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
FRONT RIGHT
1 – Tray
2 – Lock Ring
3 – Storage Compartment/Remote
4 – Elevating Foot
5 – Elevating Adjustment Wheel
6 – Elevating Foot Release Button
7 – Lens
8 – Viewer (Model 5600)
9 – Focus Knob
10 – Select Bar
11 – Timer (Model 5600)
12 – Reverse
13 – Forward
14 – Power/Fan/Lamp
BACK RIGHT
15 – Tray Release Latch
16 – Lamp Module
17 – Reading Light
18 – Room Light Outlet (Model 5600)
19 – Remote Control Receptacle
BASE
20 – Power Cord
21 – Power Cord Retainer
22 – Leveling Foot
KODAK CAROUSEL® Slide Projector
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
Startup
Open the storage compartment and remove the remote control.
Plug the 5-pin cable remote connector into the remote-control receptacle,
aligning the raised dot with the metallic rivet head.
Plug the power cord into a grounded outlet with 110- to 125-volt 60 Hz
current only.
4
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Loading the Slide Tray
A KODAK CAROUSEL® 140 Slide Tray is designed to hold up to 140 slides.
Be sure that your slide mounts are in good condition; frayed or bent mounts
may fail to drop into the projector. A variety of slide trays are available with
capacity up to 140 slides. See your dealer in Kodak products for a complete
list of Kodak trays and accessories.
Note: Do not attempt to project slides mounted with sticky or loose tape.
Place the tray over the center post of the projector. Align the "0" slot with the
gate index; the tray will drop into position.
If your 140-slide tray does not drop easily, secure the lock ring, invert the
tray, and align the index hole with the index notch. Slide and hold the tray
release latch in the direction of the arrow, and turn the bottom plate until the
index hole and notch align. Then release the latch. If you use an 80-slide tray,
rotate the metal plate on the bottom of the tray until it locks into position.
140-Slide Tray
80-Slide Tray
KODAK CAROUSEL® Slide Projector
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Adding Your Slides Remove the lock ring by turning it counterclockwise and lifting it off.
Check each slide’s orientation (horizontal or vertical), and arrange them in the
order you wish to show them. Then turn the slides upside down.
Number each mount in the upper right-hand corner of the film’s shiny side.
Insert your first slide into the first slot in the tray so that the number is visible
on the outer circumference of the tray. Insert your second slide in the second
slot with the emulsion (dull side) facing your first slide, and so on.
6
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Replace the lock ring by turning it clockwise until it is secure
Tray
Place the loaded slide tray on the projector. Align the tray index bar with the
gate index. The tray will drop into position.
KODAK CAROUSEL® Slide Projector
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Removing the Tray To remove the slide tray:
• press the select bar all the way down
• align the tray index bar with the gate index.
You can then lift off the tray.
8
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Projecting Your Slides
Lens
To insert a lens, push the focus knob up and position the lens gear teeth on
the lens barrel with the notch on the projector.
Lamp
Slide the power switch to lamp.
KODAK CAROUSEL® Slide Projector
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Forward and
Reverse
Press the forward button on the projector or the remote control to project the
first slide. To change slides, briefly press the forward or reverse buttons.
Focus
Focus your first slide using the focus knob on the projector or the focus button
on the remote control (Models 4400 and 5600 only).
Autofocus
(Models 4400 and
5600 only)
The autofocus feature automatically focuses each slide after you focus your
first slide manually. If there is a mix of slide mounts in the tray (cardboard,
plastic, and glass), it may be necessary to manually refocus between
mount-type changes. The focus button on the cabled remote can be used for
Models 4400 and 5600.
Random Projection For random projection of any slide in the
tray:
• press and hold down the
select bar,
• rotate the tray to the desired slide,
and
• release the select bar.
10
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Screen Image
Use the elevating foot to horizontally center the projected image on the
screen. To release the foot, press the release button, while lifting the front of
the projector to the desired height. Use the elevating wheel to make fine
adjustments.
If the image is not level, make an adjustment by turning the leveling foot at
the rear of the projector.
Timer
(Models 4400 and
5600 only)
To time your slides, use the timer switch for slide changes from 3 to
22 seconds.
To interrupt the timer, press either
the forward or reverse button. For
manual operation, slide the timer
switch to Off.
KODAK CAROUSEL® Slide Projector
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Reading Light
(Model 5600 only)
To illuminate a small area for reading, lift the reading light cover while the
projector lamp is on.
Room Light Outlet Plug any standard room light into the room light outlet and turn it on. It will
remain on until the projector is turned to the lamp position (when a darkened
room is required). When you turn the projector off at the end of your
presentation, the room light will come on again.
(Model 5600 only)
12
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Single Slides
To project single slides, slide the power switch on. Remove the tray and insert
a slide upside down into the projector gate. Push the slide all the way down.
After viewing the slide, press
forward, reverse, or the select bar to eject the slide.
Selecting Slide
Projection Lenses
When buying a lens, consider features such as focal length (measured in
millimetres), aperture (designed as an f/stop), and the lens design (curved or
flat).
When selecting a lens, remember that the shorter the focal length (i.e., the
smaller the f/number), the brighter the projected image. Also, a curved-field
lens, in combination with cardboard open face mounts from an automated
mounting process, provide superior projection quality. A flat-field lens is the
best choice for glass-mounted slides.
KODAK CAROUSEL® Slide Projector
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Choosing a Curved- The lens you select depends on how you use your projector and what type of
slide mount you use. So that you may choose the lens that best meets your
needs, we do not include a lens with the projector.
or Flat-Field Lens
To obtain the best results of a projected image, insert slides with the emulsion
side toward the projection lens, slide curve toward the light source.
A flat-field lens works best for:
• general home projection
• glass mounts
• plastic mounts
• mixed mounts
• non-embossed cardboard mounts
• rear-projection applications
• duplicated slides
A curved-field lens works best for:
• embossed cardboard mounts
(Embossed mounts have beveled edges around the aperture. Kodak
Premium Processing and Kodak Processing labs provide embossed
mounts.)
Lens Focal Length/ Use the illustration on the following page to help determine the lens focal
length and projector distance.
Projector Distance
14
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
KODAK CAROUSEL® Slide Projector
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Editing Your Presentation
Removing the
Lock Ring
To add or remove slides in the tray, you must first remove the lock ring.
Turn the ring counterclockwise and lift off.
Removing a Slide
Rotate the tray to the slide you wish to remove. Firmly press and hold down
the select bar to eject the slide.
Adding a Slide
When the lock ring is off, you can add a slide to any empty slot. (See “Adding
Replace and secure the lock ring.
16
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Clearing a Gate Jam
To remove a defective slide or foreign object stuck in the projector gate, you
need to remove the tray.
• Slide the tray release latch in the direction of the arrow, and
• with your other hand, lift off the back of the tray.
With the lock ring firmly in place,
turn the 140-slide tray upside
down. Retract the tray release
latch in the direction of the arrow
and align the index hole with the
index notch. (For an 80-slide tray,
rotate the metal plate until it locks
into position.) Put the tray aside.
Remove the slide or object from the
projector gate by pressing the
forward button or removing the
slide manually.
Remount damaged slides to protect
your projector and slides from
subsequent damage.
KODAK CAROUSEL® Slide Projector
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Using the Built-In Viewer
(Model 5600 Only)
Important
Before opening the viewer, you must remove the projection lens from the
projector.
Removing the
Lens
Turn the focus knob to the horizontal position. Push the knob toward the top
of the projector as you withdraw the lens.
Opening the
Viewer
Grasp the viewer handle and pull it out from the base of the projector. It will
pop into place.
Slide the power switch to lamp to project your slides.
Closing the Viewer To close the viewer, fold it and push it back into the body of the projector.
18
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Reinserting the
Lens
To reinsert the lens, push the focus knob up and position the lens gear teeth
on the lens barrel with the notch on the projector.
Shutdown
To shut down,
• remove and store the tray
• slide the power switch to off
Your projector will remain warm for several minutes.
KODAK CAROUSEL® Slide Projector
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
To ensure a long life and trouble-free operation for your projector:
• Allow the air to flow freely around the projector.
• Do not recirculate warm air.
• Keep the projector dust free.
Your CAROUSEL Projector requires no lubrication; all bearings are self-
lubricating.
Projection Lamps
Included: FHS lamp, 70-hour lamp life (medium-brightness)
Sampling of other lamps:
EXY (200 hours/less brightness)
EXR (35 hours/maximum brightness)
Note: An EXW lamp is not recommended for older models of CAROUSEL
Projectors. Contact the Kodak Information Center at 1-800-242-2424 in the
U.S. or 1-800-465-6325 in Canada if you need help identifying your
particular model.
Lamp Tips
• Projector operation on line voltages above 125 volts greatly
reduces the lamp life.
• Unplug the projector before changing the lamp.
20
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Changing the Projection Lamp
Slide the power switch to Off and unplug the projector.
Allow the projector and lamp
to cool for about 10 minutes.
Push the lamp-module
release button and remove
the lamp module.
Note: There is an additional
safety latch, which reduces
the chance of an accident
with a loosely inserted lamp
module, that may cause some
resistance. To release the
latch, you may need to apply
extra effort when you pull out
the module.
Lift up the lamp release clip. Carefully remove the worn lamp from the
socket and place it on a heat-resistant surface.
Insert a new lamp into the
socket. Push down to tightly
seat the replacement lamp.
Relatch the clip in the forward
position and push the lamp
module all the way back into
the projector until it latches.
KODAK CAROUSEL® Slide Projector
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the Condenser, Heat-Absorbing Glass, and
Mirror
To clean the condenser, heat-absorbing glass, or mirror, you must disassemble
the lamp module.
Slide the power switch to Off and
unplug the projector. Allow the
projector to cool about 10 minutes.
Push the lamp-module release
button and remove the lamp
module.
Use a torx-head screwdriver to
remove the screw.
Using a flat-blade screwdriver, apply ample
pressure to release each of the metal tabs.
Lift off the top of the lamp module.
22
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Condenser Lens
You can clean the condenser lens in place, or by pulling it out. Wear gloves
to prevent fingerprints.
Caution
Heat-Absorbing
Glass
The heat-absorbing glass is fragile. Handle it only when cool.
(For lamp modules
with a heat-absorbing
glass.)
The green-tinted heat-absorbing glass easily removes for cleaning.
KODAK CAROUSEL® Slide Projector
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Reassembling the
Lamp Module
To reassemble the lamp module, you will need to align and insert each tab
into its appropriate slot.
Start with the tabs in the rear of the lamp module.
Insert the remainder of the tabs into slots until all 7 tabs on the top and 2 on
the bottom are secured. Insert the screw and tighten. Then insert and seat the
lamp.
24
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Mirror
To clean the mirror, invert the lamp module to reach the mirror. Gently clean
the mirror with a soft, lint-free cloth moistened with lens cleaner.
When your maintenance is complete, push the lamp module back into the
projector.
KODAK CAROUSEL® Slide Projector
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Consult this guide before calling for service.
PROBLEM
CAUSE
CORRECTION
Projector does not operate
No power to projector
Plug power cord into suitable
electrical outlet. Set power
switch to Lamp.
No illumination on screen with slide in Power switch on Off or Fan
Set switch to Lamp.
projector gate
Lamp burned out
Install new lamp or lamp module
Check lamp.
Lamp not seated in socket
Slide not in proper focus on screen
focus.
Slide itself not sharp
Examine slide for proper focus.
First slide in tray not properly focused Focus center of first slide
manually.
Slide in different type of mount from
others
Focus manually.
Projection lens installed improperly
Read and follow the instructions
for installing the lens.
Uneven edge-to-edge focus
Slide itself is not sharp
Examine slide.
Curved field lens used with glass,
plastic, or non-embosssed mounts
Try a flat field lens.
(See “Choosing a Curved- or
Curved field lens used for rear
projection
Use a flat field lens.
Lamp performance
UInstall new lamp and try again.
Turn off autofocus.
Autofocus motor runs continuously
Autofocus fails to operate
Multi-aperture slide or matte-suface
write-on slides in tray
Lamp performance
Install new lamp and try
autofocus again.
26
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
PROBLEM
CAUSE
CORRECTION
Slide fails to drop into projection
position
Tray base plate not properly indexed
Align the index hole and index
notch.
Tray not properly positioned on
projector
Reposition tray on projector.
Slide mount warped or frayed at
corners slide.
Straighten mount or remount
slide.
Projector not level or tilted too high
Set projector on a stand equal
with center of screen.
Uneven illumination on screen
Projection lamp not fully seated
Check lamp.
Condenser lens not installed or not
positioned properly in mount
Check condenser lens.
Slide mount not seated properly in
projector gate
Check slide position and slide-
mount condition.
Projector won't cycle to next slide
Tray not properly positioned
Reposition tray.
Slide or foreign object stuck in gate
See "Clearing a Gate Jam" on
page 17.
27
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Warranty
Kodak warrants this KODAK CAROUSEL Slide Projector to function
properly for one year from the date of purchase.
If this KODAK CAROUSEL Slide Projector does not function properly
within the warranty period, upon submission of dated proof of purchase,
Kodak will repair it without charge, except for worn-out projector lamps. If
Kodak is unable to repair the projector, the option of replacement or refund of
the purchase price will be available.
Limitations
This warranty does not cover circumstances beyond Kodak’s control,
projector lamps, or problems caused by failure to follow the care and
operating instructions in the manual.
Any modification to the original design of this projector nullifies this
warranty.
Warranty service will not be provided without dated proof of purchase.
Kodak makes no other express warranty for this product.
Repair or replacement is Kodak’s only obligation. Kodak will not be
responsible for any consequential or incidental damages resulting from
the sale or use of this projector, regardless of the cause of such damages.
Your Rights Under Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to
you. This warranty gives you specific legal rights, and you may also have
other rights that vary from state to state.
State Law
28
KODAK CAROUSEL® Slide Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Obtain Service
Assistance
To obtain service or for assistance in using your KODAK CAROUSEL Slide
Projector, contact the Kodak Information Center at 1-800-242-2424,
Monday through Friday, 8 a.m. to 8 p.m. (Eastern time). In Canada, call
1-800-465-6325, Monday through Friday, 8:30 a.m. to 5 p.m. (Eastern time).
Or call Kodak in your country.
Shipping
Instructions
To help us get your KODAK CAROUSEL Slide Projector back to you
promptly, please enclose a note giving details of the problem, dated proof of
purchase, and your complete name and shipping address. Pack the unit in a
sturdy carton with ample packing material to protect the unit during shipping
and handling.
KODAK CAROUSEL® Slide Projector
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Imaging
EASTMAN KODAK COMPANY
Rochester, New York 14650
Kodak, Ektagraphic, and Kodalux are trademarks.
CONSUMER IMAGING
Part No. 5B4904 9/99 Minor Revision ©EastmanKodak Company Printed In U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|