|
User’s Guide
KODAK DP2000
Digital Projector
with KODAK Image
Manager Software
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Safety Certifications
UL, CUL, TÜV, NOM
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be
required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.
Declaration of Conformity
Manufacturer: Eastman Kodak Company
Rochester, New York 14650 USA
We declare under our sole responsibility that the KODAK DP2000 Digital Projector conforms to the following directives
and norms:
Directive 89/ 336/ EEC, Amended by 93/ 68/ EEC
EMI: EN 55022 (1992) Class A
EMC: EN 50082-1 (1992)
IEC 801-2, IEC 801-3, IEC 801-4
Directive 73/ 23/ EEC, Amended by 93/ 68/ EEC
Safety: EN 60950: 1992 + A1 + A2 + A3: 1995
July, 1999
Australian Certification C-tick mark
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Important Operating Considerations . . . . . . . . . . . . . . . . . . 2
Battery Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Image Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Usage Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
If You Need Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting up the Projector . . . . . . . . . . . . . . . . . . . . . . 11
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Starting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Turning Off the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Using the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Basic Image Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Adjusting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
The Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Using the Keypad and Remote Control . . . . . . . . . . . . . . . 23
Using the On-Screen Menus . . . . . . . . . . . . . . . . . . . . . . . . 25
Kodak Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Maintenance & Troubleshooting . . . . . . . . . . . . . . . 37
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Replacing the Projection Lamp . . . . . . . . . . . . . . . . . . . . . . 38
Replacing the Batteries in the Remote Control . . . . . . . . . 41
Using the Kensington Lock . . . . . . . . . . . . . . . . . . . . . . . . . 41
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
v
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Appendix B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Portable and Laptop Activation Chart . . . . . . . . . . . . . . . . 49
Appendix C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Using Video Mirroring with a PowerBook Computer . . . . 59
Appendix D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Projected Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Please read and follow all safety instructions provided before using
your new projector. Failure to comply with safety instructions may
result in fire, electrical shock, or personal injury and may damage or
impair protection provided by equipment. Please save all safety
instructions.
Safety Definitions
•
Warning: Statements identify conditions or practices that could
result in permanent personal injury.
•
Caution: Statements identify conditions or practices that could
result in damage to your equipment.
Safety Symbols
Attention: For information about use of a feature, please refer
to this User’s Guide.
Warning: Hot surface. Do not touch.
An arrow pointing to the lamp door on the projector.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Safety Terms
•
Warning: Don’t look directly into the lens when the projector is
turned on.
• Warning: To replace the lamp, turn the power off and
unplug the power cord. To avoid burns, wait 30 minutes
before opening the lamp door. Follow all instructions pro-
vided in this User’s Guide.
• Warning: Please use the power cord provided. Connect
the power cord to a receptacle with a protective safety
(earth) ground terminal.
•
Warning: Refer all service to qualified service personnel. Servic-
ing your own projector will void the warranty. See “If You Need
Assistance” on page 8 for the customer service contact informa-
tion.
•
•
Caution: Don’t block ventilation openings.
Caution: Don’t set liquids on the projector. Spilled liquids may
damage your projector.
•
•
Caution: Don’t place the projector on a hot surface or in direct
sunlight.
Caution: Do not drop the projector. Transport the projector in a
Kodak-approved case.
Important Operating Considerations
Do not place the projector on a tablecloth or other soft covering that
may block the vents. In the unlikely event of the bulb rupturing,
thoroughly clean the area behind the projector and discard any edible
items placed in that area.
Do not place objects in
this area behind the projector
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Battery Use
Read and follow all warnings and instructions supplied by the battery
manufacturer.
Keep batteries away from children.
Store batteries in their original packaging.
When inserting batteries, verify that the (+) and (-) terminals are
aligned correctly.
Replace all batteries of a set at the same time.
Do not mix new batteries with used ones.
Do not use batteries of different chemistries, capacities, brands or
sizes together. Leakage could result.
Do not disassemble, recharge, or short-circuit batteries.
Do not subject batteries to high temperature or fire.
Discard used batteries according to all applicable local and national
regulations. Utilize established community battery recycling
programs where they are available. Consult battery manufacturers for
additional information for disposing of batteries.
In the unlikely event of contact with battery electrolyte, customers in
the U.S. can contact the Kodak Information Center (KIC) at
1-800-242-2424. U.S. customers can also contact KIC for
information regarding electrolyte removal from KODAK product
components.
Customers outside the U.S. can contact their local Kodak Customer
Service representative.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The KODAK DP2000 Digital Projector is specifically designed for
the mobile presenter. It packs XGA 1024 x 768 graphics with
16.7 million colors into a small, 4.8 pound package. It generates
crisp, clear images using Digital Light Processing™ (DLP)
technology. The DP2000 is easy to connect, easy to use, easy to
transport, and easy to maintain.
Included with the DP2000 is Kodak’s exclusive Image Manager
feature. With this feature you can select the image display setting best
suited for your specific presentation material and projection
environment.
Image Resolution
The XGA resolution of the DP2000’s projected image is 1024 x 768.
The projector cannot compress screen resolutions above 1024 x 768.
If your computer’s screen resolution is higher than 1024 x 768, reset
it to a lower resolution before you connect the projector.
The DP2000 automatically expands 640 x 480 and 800 x 600 images
to 1024 x 768. You can display these images at their native
resolutions by turning off the Auto Resize feature. See “Auto Resize”
on page 28 for more information.
Compatibility
The projector is compatible with a wide variety of computers and
video devices, including:
• IBM-compatible computers, including laptops, up to
1024 x 768 resolution.
• APPLE MACINTOSH and POWERBOOK computers up
to 1024 x 768 resolution.
• Most standard VCRs, DVD players, camcorders and laser
disc players.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Unpacking the Projector
The projector comes with the items shown here. Check to make sure
that all are included. Contact your dealer of KODAK products
immediately if anything is missing.
1
2
3
5
4
9
8
11
6
10
7
1.
2.
3.
4.
5.
Digital projector and lens cap
Soft carry case
6.
7.
8.
9.
VESA computer cable
Audio cable adapter
Audio cable
Remote control
Power cords (U.S., U.K, Euro)
Composite video cable
User’s Guide, Quick Start Guide,
and Online User Guide CD
10.
11.
USB mouse cable
PS/2 mouse cable
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Projector Features
speaker
keypad
Hand grip
zoom ring
KENSINGTON
Lock
connector panel
focus ring
power
cord
connector
Usage Guidelines
• Do not look directly into the projection lens when the lamp
is turned on. The bright light may harm your eyes.
• Do not block the grills on the projector. Restricting the air
flow can cause it to overheat and turn off. If this happens,
you must wait a minute before attempting to turn it back
on.
• Handle the projector as you would any product with glass
components. Be especially careful not to drop it.
• Avoid leaving the projector in direct sunlight or extreme
cold for extended periods of time. If this happens, allow it
to reach room temperature before use.
• Transport the projector in a Kodak-approved hard or soft
case.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
If You Need Assistance
The first place to look for help is in “Maintenance &
Troubleshooting” on page 37. But you can also get help online, by
fax, or by phone.
Online Services
Contact Kodak via:
World Wide Web
(click on Service and Support)
America Online
CompuServe
(keyword) KODAK
GO KODAK
ftp.kodak.com
Faxed Information
Kodak offers automated support by fax:
U.S. and Canada
Europe
1-800-508-1531
44-0-131-458-6962
44-0-131-458-6962
U.K.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Customer Support
If you have questions concerning the operation of your KODAK
projector, you can speak directly to a customer support representative.
Have the projector serial number ready, and be at your computer with
your projector when you call.
In the U.S. and Canada call toll free, 1-888-375-6325, between the
hours of 9:00 a.m. and 8:00 p.m. (Eastern Standard Time) Monday
through Friday.
The International Toll Line is +44 (0) 131 458 6714.
In Europe call
Austria/Osterreich
Germany/Deutschland
Spain/Espana
0179 567 357
069 5007 0035
91 749 76 53
02 713 14 45
01 407 3054
Belgium/Belgique
Ireland/Eire
Sweden/Sverige
Denmark/Danmark
Italy/Italia
08 587 704 21
3 848 71 30
02 696 334 52
01 838 53 51
0800 1 17056
020 346 9372
0870 2430270
01 55 1740 77
23 16 21 33
Switzerland/Schweiz/Suisse
Finland/Soumi
Netherlands/Nederland
UK (National Line)
France
Norway/Norge
1 Int. Fax Line
+44 (0) 131 458 6962
9
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Warranty
This product is backed by a limited two-year warranty. The details of
the warranty are printed at the back of this manual. A longer term
warranty can be purchased from your dealer of KODAK products.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Projector
This section describes how to:
• determine where to position the projector
• connect the projector to a computer or a video player
• turn on and turn off the projector
If you are experienced in setting up presentation systems, use the
Quick Start card that came with the KODAK DP2000 Digital
Projector. Otherwise, follow the procedures described here.
Positioning the Projector
Note: If you want to project from behind a translucent screen, set up
the projector behind your screen. See “Rear Projection” on
page 31 to reverse the image.
1. Make sure your projector is on a flat surface. It must be within 10
feet (3 m) of your power source and within 6 feet (1.8 m) of your
computer.
2. Position the projector the desired distance from the screen.
•
The distance from the lens of the projector to the screen and
the zoom setting determine the size of the projected image as
shown here. For more information about image sizes at
minimum and maximum zoom settings, see “Projected Image
Size” on page 61.
13
10
f
t
.
(
3
4
f
m
t
(
)
3
7.
.
1
8
6.
m
f
2
t
)
(
f
t
2
3
(
(
.
4
.
1
2
2.
.
m
9
f
5
t
)
m
(
f
.
.
t
9
)
.
.
m
8
)
m
.
)
.
20 ft.
6 m
12 ft.
3.7 m
5 ft.
1.5 m
3. Make sure the projector and your computer are turned off.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Connecting the Projector
,FRQVꢀRQꢀWKHꢀSURMHFWRUꢀZLOOꢀDLGꢀ\RXꢀZKHQꢀFRQQHFWLQJꢀWKHꢀSURMHFWRUꢀWRꢀDꢀ
FRPSXWHUꢀRUꢀYLGHRꢀSOD\HUꢁ
&DXWLRQꢀꢁ 7XUQꢁRIIꢁWKHꢁFRPSXWHUꢂꢁPRQLWRUꢁDQGꢁSURMHFWRUꢁZKHQHYHUꢁ
\RXꢁFRQQHFWꢁWKHꢁFRPSRQHQWVꢃꢁ
power connection
DLP
A TEXAS INSTRUMENTS TECHNOLOGY
Includes
Image Manager
S-video
composite video
audio in
mouse
VESA computer input KENSINGTON lock
Connecting to a Computer
When you connect the projector to a computer, make sure that the
distance between it and the projector is 6 feet or less.
Always use the power cord and VESA cable that shipped with the
projector. A surge-protected power strip is recommended.
Many laptop computers do not automatically turn on their external
video port when a secondary display device such as a projector is
connected. Refer to your computer manual for the command that
activates the external video port. Activation commands for some
laptop computers are listed in Appendix C.
Note: If you are connecting an older Macintosh computer that does
not have a 15-pin connector, use the optional Mac adaptor.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Projector
To connect to a computer:
1. Plug one end of the VESA computer cable into the video
connector on your computer.
2. Plug the other end of the VESA computer cable in the
connector on the projector
audio cable
VESA cable
Do you want to play your computer’s audio on the
projector?
1. Plug either end of the audio cable into the audio connector on
your computer.
2. Plug the other end of the audio cable into the
the projector.
connector on
13
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Do you want to control the computer’s mouse from the
projector’s remote control or keypad?
If your computer has a PS/2 connector, use the PS/2 mouse cable.
1. Plug the 6-pin end of the PS/2 mouse cable into the mouse
connector on your computer.
2. Plug the 8-pin end of the PS/2 mouse cable into the
on the cable hub.
connector
If your computer has a USB connector and is running a USB
compatible operating system, use the USB mouse cable.
1. Plug the
end of the USB mouse cable into the mouse
connector on your computer.
2. Plug the end of the USB mouse cable into the
connector
on the projector.
Note: A USB mouse is hot-pluggable, meaning that you do not
need to restart your computer after connecting the mouse to
use the mouse. A PS-2 mouse is not hot-pluggable.
Now you’re ready to start the projector and computer. Skip to
“Starting the Projector” on page 17.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Projector
Connecting to a Video Player
If your video player uses a round, one-prong composite video
connector, you’ll only need the audio cable, audio adapter, and
composite video cable that shipped with the projector.
If your video player uses a round, four-prong S-video connector,
you’ll need an S-video cable in addition to the audio cable and audio
adapter. The S-video cable is sold separately.
Note: Your video player may have a "Video Out" connector for a
coaxial cable connection. Do not use this to connect to the
projector.
To connect to a video player:
1. Plug the composite video cable yellow connector into the
“video-out” connector on your video player. This connector may
be labeled “To Monitor.”
•
If you’re using an S-video cable, connect it to the
“S-video out” connector on the video player.
2. Plug the other yellow connector into the composite video
connector on the back of the projector.
If you’re using S-video, plug the other end of the cable into
•
the “S-video” connector
on the projector.
Connecting with
composite
video cable
audio adaptor
composite
video cable
audio cable
15
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Connecting with
S-video cable
audio
adapter
S-video
cable
audio cable
3. Plug the plug the audio adapter white connector into the left
“audio out” port on your video player. Plug the adapter red
connector into the right “audio out” port on the video player.
4. Plug the other end of the audio adapter into the audio cable.
5. Plug the audio cable into the "audio in"
projector.
connector on the
The projector is compatible with these major broadcast video
standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, and SECAM. It
automatically adjusts to optimize its performance for the incoming
video. See “Video Standard” on page 30 for details.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Projector
Starting the Projector
Note: We recommend using a surge protector power strip.
1. Remove the lens cap.
2. Plug the power cord into the side of the projector, and then plug it
into your electrical outlet.
The fans start to run and the lamp LED on top of the projector
lights orange until the software has initialized. Then the LED
lights green.
3. Turn on the lamp by pressing the
The KODAK startup screen appears.
button on the keypad.
4. If you connected the projector to a video player, turn on the video
player.
•
The video image should appear on the projection screen. If a
computer source is active, press the button on the
keypad (page 23) or the button on the remote to display
your video image. You can select a default source to
determine which source the projector examines first during
power-up for active video; see “Default Source” on page 31.
•
Use the
buttons to adjust the volume.
5. If you connected the projector to a computer, turn on the
computer. Make sure the computer external video port is
activated. See “Portable and Laptop Activation Chart” on page 49.
Note: With some computers, the order in which you power up
the equipment is very important. Most computers should
be turned on last, after all other peripherals have been
turned on. Refer to your computer documentation to
determine the correct order.
•
The computer image should appear on the projection screen.
If a video source is active, press the button on the
button on the remote to display
keypad (page 23) or the
your computer’s image.
•
If necessary, make adjustments to the image using the
projector’s on-screen menus. To open the menus, press the
button on the keypad or remote, then select the Display
or Image sub-menu. For more information about the menus,
see “Using the On-Screen Menus” on page 25.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Turning Off the Projector
To completely turn off the projector, unplug it. If you want to turn the
projector back on immediately, you must allow about a minute for the
lamp to cool. The lamp won’t light if it’s too hot.
Note: Lamp life will be extended if you turn the lamp off, then wait
1 minute while the lamp cools before unplugging the
projector. The Lamp LED will light green when the lamp has
cooled. See page 24 for details on the Lamp LED.
If you want to turn off the display for a short period of time, press the
button on the keypad or remote. This blanks the screen for fifteen
minutes, but keeps the projector running. (You can change the amount
of time the projector stays in standby mode; see “Standby Time” on
page 31 for details.) After 15 minutes, the lamp goes out (the
projector keeps running). To exit standby mode, press the
button
again. (It may take several seconds for the projection lamp to reach
full power and project the image again.)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Projector
This section describes how to use and make adjustments to the
projector. It also provides a reference to the keypad and remote
control buttons and the options available from the on-screen menus.
Basic Image Adjustment
1. Make sure you have turned on your equipment in the right order
(page 17).
2. If the image doesn’t display completely, zoom the image
(page 20), adjust the height of the projector (page 20) or center
the image by adjusting its horizontal or vertical position
(page 29). Be sure the projector is at a 90 degree angle to the
screen.
3. If the image is out of focus, rotate the focus lens (page 20).
4. If the image appears to shimmer or if it has blurry vertical bars
after you have adjusted the focus, turn Auto Image (page 28) off
and then back on to reset the automatic sync and tracking. If that
doesn’t clear up the image, turn Auto Image off and adjust the
sync (page 29) and/or the tracking (page 29) manually.
5. If the colors don’t look right, check the KODAK Image Manager
settings. See “Kodak Menu” on page 35
Or
Adjust the brightness (page 26) and the tint (page 27).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Adjusting the Projector
To focus the image, rotate the focus ring until the image is clear. To
zoom the image, rotate the zoom ring. This adjusts the image size
without affecting focus.
zoom ring
focus ring
The projector is equipped with a self-locking, quick-release elevator
foot and button.
To raise the projector:
1. Press and hold the elevator button.
2. Raise the projector to the height you want, then release the button
to lock the elevator foot into position.
Elevator foot
Elevator button
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Projector
The Remote Control
The projector ships with a remote that has four function buttons, a
disk mouse and two mouse buttons, one on the top of the remote and
one on the bottom.
Point the remote control at the projection screen or at the front or rear
of the projector. The range for optimum operation is about 25 feet
(7.6 m). If you point the remote at the projection screen, the distance
to the screen and back to the projector must not be more than 25 feet
(7.6 m). For best results, point the remote directly at the projector.
disk mouse
simulates the right mouse button
simulates the left mouse button
Note: If the remote is inactive for several minutes, it “sleeps” to
conserve battery life. Press any button except the disk mouse
to re-activate the remote.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Press anywhere on the edge of the disk mouse to move the cursor on
the screen. You can move the cursor at any angle by pressing the
corresponding edge of the disk. The mouse button on the top of the
remote simulates your computer’s right mouse button; the button on
the bottom simulates your computer’s left mouse button. See “Using
the Keypad and Remote Control” starting on page 23 for a description
of the four function buttons.
®
®
If you are creating presentations in MICROSOFT POWERPOINT ,
you can use the remote’s mouse buttons to navigate through your
presentation while in Slide Show mode. To configure POWERPOINT
for this, choose Options from the Tools menu, click the View Tab,
de-select the “Popup Menu on Right Mouse Click” option in the Slide
Show section, then click OK. Then, when you’re in POWERPOINT’s
Slide Show mode, a left click advances to the next slide and a right
click returns to the previous slide (other POWERPOINT modes are
not affected).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Projector
Using the Keypad and Remote Control
While the menus are displayed, the volume, source, and standby buttons on
the keypad act as menu navigation buttons. See “Using the On-Screen
Menus” on page 25 for details.
The Keypad Buttons.
lamp on/off
lamp LED
source button - toggles
menu button -
back and forth
displays a menu of
between video and
projector options on
computer sources
the screen
volume -
decreases volume
volume -
increases volume
standby - turns off the
image without turning
off the projector
The Remote Control Buttons
disk mouse
simulates the right mouse button
menu
standby
computer
video
23
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Lamp on/off (keypad only)
Press the
button to turn the lamp on or off. The Lamp LED
indicates the state of the lamp. A green Lamp LED indicates that you
can turn the lamp on, or the lamp is currently on. An orange LED
indicates the software is initializing or the lamp is cooling. Do not
press the
button when the LED is orange.
Menu
Press
Press
to open the on-screen menus (the keypad lights green).
again to close the menus. When you close the menus, the
projector saves any changes you made. For more information about
the on-screen menus, see “Using the On-Screen Menus” on page 25.
Source (keypad only)
(remote control only)
or Computer and Video
When you have more than one source (computer and video)
connected to the projector, select between them by pressing the
button on the keypad or the
or
button on the remote.
Standby
When you press , the display and audio turn off and a blank screen
is displayed for 15 minutes. You can change the amount of time the
projector stays in standby mode; see “Standby Time” on page 31 for
details.
•
•
•
If you press
to normal operations immediately.
If you don’t press
minutes.
If you press
again within 15 minutes, the projector returns
again, the lamp turns off after 15
again after 15 minutes, wait until the lamp
LED is green.
Volume (keypad only)
• To increase the volume, press
• To decrease the volume, press
.
Volume adjustments are saved for each source that you have
connected.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Projector
Using the On-Screen Menus
The projector has seven drop-down menus that allow you to make
image adjustments and change a variety of settings. Most of these
adjustments aren’t available directly from the keypad.
Note: Some menu items may be grayed out at certain times. This
indicates that the item is not applicable to your setup (for
example, video standards do not apply to computer sources)
or the item is not enabled until another selection is made (for
example, Manual Tracking is not available until Auto Image
is turned off).
To open the on-screen menus, press the
button on the keypad or
remote. This changes the volume, source, and standby buttons on the
keypad to menu navigation buttons. Press the corresponding buttons
to move the cursor up, down, left, or right, or use the disk mouse on
the remote. To select a menu, move the cursor left and right to
highlight the menu you want. The drop-down menu appears.
:KHQꢀWKHꢀPHQXꢀRSWLRQꢀLVꢀDFWLYHꢂꢀ
XVHꢀWKHVHꢀEXWWRQVꢀWRꢀQDYLJDWHꢀ
WKURXJKꢀWKHꢀPHQXVꢁ
To change a menu setting, use the up and down navigation buttons on
the keypad or the disk mouse on the remote control to move the
cursor up and down to the item you want to change (the selected item
is highlighted red), then use the left and right navigation buttons to
adjust a setting.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Some submenus, such as Brightness, consist of a slider bar you use to
increase or decrease a value. Some submenus, such as Standby Time,
consist of options you scroll through to select the desired one. All
changes are saved when you close the menus.
To access another menu, use the up and down navigation buttons or
the disk mouse on the remote control to move back to the top of the
current menu, then use the left and right navigation buttons to move
to another menu.
Display Menu
ꢀ
Brightness
Adjusting the brightness changes the intensity of the image.
• Press the left navigation button to darken the image.
• Press the right navigation button to lighten the image.
Contrast
Contrast controls the degree of difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
• Press the left navigation button on the keypad to decrease
the contrast.
• Press the right navigation button on the keypad to increase
the contrast, making the blacks appear blacker and the
whites appear whiter.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Projector
Tint
The tint adjusts the red-green color balance in the projected image.
Changing the Tint setting has no effect on PAL or SECAM video
sources.
• Press the left navigation button on the keypad to increase
the amount of green in the image.
• Press the right navigation button on the keypad to increase
the amount of red in the image.
Color
The color setting adjusts a video image from black and white to fully
saturated color.
• Press the left mouse button to decrease the amount of color
in the image.
• Press the right mouse button to increase the amount of
color in the image.
Blank Screen
Blank Screen determines what color is displayed when there is no
active source and when the projector is in standby. Click the left or
right navigation button to toggle between blue and black.
Reset All
Click the left or right navigation button to reset all the options (except
Language, Video Standard, Rear Projection, and Standby Time) in all
the menus to their original settings.
Audio Menu
Volume
Note: Changing the volume from the menu is the same as changing
it using the keypad.
• Press the left navigation button to decrease the volume.
• Press the right navigation button to increase the volume.
Volume adjustments you make are saved for each source.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Image Menu
ꢀ
Auto Image
Note: Some screen savers interfere with the operation of Auto
Image. If you’re experiencing problems, try turning your
screen saver off, then turning Auto Image off and back on.
The projector automatically adjusts tracking, signal synchronization
and vertical and horizontal position for most computers (Auto Image
does not apply to video sources). If you want to adjust these features
manually, you must turn off Auto Image first by highlighting Auto
Image in the Image menu and clicking either the left or right
navigation button to select “off”.
Auto Resize
Auto Resize automatically resizes the image by scaling it up. It only
affects computer images that are not the projector’s native resolution.
When Auto Resize is on, the projector makes the best fit of the image to
the screen. If you turn Auto Resize off (by highlighting it in the Image
menu and clicking the left or right navigation button to select “off”),
the image may be either cropped or too small for the screen.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Projector
Manual Sync
Note: The Manual Sync option is available only for computer
sources. The projector sets this option automatically for a
video source.
The projector adjusts signal synchronization automatically for most
computers. But if the projected computer image looks fuzzy or
streaked, try turning Auto Image off then back on again. If the image
still looks bad, try adjusting the signal synchronization manually:
1. Turn Auto Image off.
2. Highlight Manual sync, then press the left or right navigation
button repeatedly until the image is sharp and free of streaks.
Manual Tracking
The projector adjusts tracking automatically to match the video signal
from your computer. However, if the display shows evenly spaced,
fuzzy, vertical lines or if the projected image is too wide or too
narrow for the screen, try turning Auto Image off then back on again. If
the image is still bad, try adjusting the tracking manually:
Note: Manual Tracking option is available only for computer
sources. The projector sets this option automatically for a
video source.
1. Turn Auto Image off.
2. Highlight Manual tracking, then press the left or right navigation
button repeatedly until the fuzzy vertical bars are gone.
Horizontal position
Note: The Horiz. Position option is available only for computer
sources. The projector sets this option automatically for a
video source.
Follow these steps to manually adjust the horizontal position:
1. Turn Auto Image off.
2. Highlight Horizontal position, then press the left navigator button
to move the image right or press the right navigator button to
move the image left.
Positioning adjustments are saved when you unplug the projector.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Vertical position
Note: The Vert. Position option is available only for computer
sources. The projector sets this option automatically for a
video source.
Follow these steps to manually adjust the vertical position.
1. Turn Auto Image off.
2. Highlight Vertical position, then press the left navigation button
to move the image down or press the right navigation button to
move the image up.
Positioning adjustments are saved when you power off the projector.
Controls Menu
Video Standard
When Video standard is set to Auto, the projector attempts to pick the
video standard (NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, or
SECAM) automatically based on the input signal it receives. (The
video standard options may vary depending on your region of the
world.) If the projector is unable to detect the correct standard, the
colors might not look right or the image might appear “torn.” If this
happens, manually select a standard by clicking either the left or right
navigation button and cycling through the standards.
Note: If you already know the video standard used in your
geographical area, it’s best to manually select it.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Projector
Standby Time
This option lets you select how long the lamp stays on and how long
the blank screen is displayed in standby mode before the projector
turns off. Select among 1, 5, 10, and 15 minutes and 1 and 2 hours by
clicking the left or right navigation button and cycling through the
options.
Rear Projection
When you turn Rear Projection on, the projector reverses the image so
you can project from behind a translucent screen. Highlight Rear
Projection, then click the left or right navigation button to turn this
feature on and off.
Default Source
Default Source toggles between Computer and Video. This
determines which source the projector checks first for active video
during power-up. Highlight Default Source and click the left or right
navigation button to toggle between the options.
Auto Source Select
This setting toggles between On and Off. When this feature is Off, the
projector defaults to the source selected in Default Source. To display
another source, you must manually select one by pressing the
button on the keypad or the
or
button on the remote control.
When this feature is On, the projector automatically finds the active
source, checking the default source first. Highlight Auto Source
Select and click the left or right navigation button to turn this feature
on and off.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Plug and Play
This setting toggles between On and Off. When it is On, most new
computers will automatically recognize the projector, then set the
monitor resolution and refresh rate accordingly. You need to set the
Plug and Play setting to Off for the projector to display properly on
some older computers. The Plug and Play setting does not affect
video images.
If the projector’s display constantly changes between the computer
image and the message, “Perfecting the image”, you may need to set
Plug and Play to Off.
Display Messages
This setting toggles between On and Off. When this feature is On,
status messages such as “No signal detected” or “Standby Active”
appear in the lower-right corner of the screen. Click the left or right
navigation button to turn this feature off and not see status messages.
Display Startup Screen
This setting toggles between On and Off. When this feature is On, the
KODAK startup screen appears when the projector starts up and
remains until an active source is detected. The startup screen contains
information on contacting Kodak. Click the left or right navigation
button to turn this feature off and display a plain black or blue screen
instead of the startup screen.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Projector
Language Menu
You can display the on-screen menus in English, French, German,
and Spanish.
Move the cursor to the language you want, then click the left or right
navigation button. The menus redraw immediately.
Status Menu
This is a read-only window for informational purposes. To display the
status window, select Show status from the menu, then click the left
or right navigation button. To remove the window, click the left or
right navigation button.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Lamp hours used
Indicates how many hours the current lamp has been in use. The
counter starts at zero hours and counts each hour the lamp is in use.
Change the bulb when the brightness is no longer acceptable. See
“Replacing the Projection Lamp” on page 38 for details.
Computer resolution
Shows your computer’s resolution setting. To change this, go to your
computer’s Control Panel and adjust the resolution in the Display tab.
See your computer user’s guide for details.
Horizontal refresh rate
The time period that one horizontal line is displayed.
Vertical refresh rate
The time period that one video frame is displayed.
Mute status
Indicates if the audio is muted.
Software version
Indicates the projector’s software version. This information is useful
when contacting Technical Support.
Source
Indicates the active source, Computer or Video.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Projector
Kodak Menu
Kodak’s exclusive Image Manager feature allows you to select the
image display setting best suited for your specific presentation
material and projection environment.
Image Manager Settings
Photo-PC Setting matches the higher contrast found on a standard
PC monitor. This option is best for:
•
•
•
images created on a PC
images from a KODAK digital camera
a starting point for composite or S-video inputs.
Photo-Mac Setting matches the lower contrast found on a standard
MACINTOSH monitor. It is generally used for images created on or
for a MACINTOSH. This setting also works well with a PC if you are
using higher than normal contrast PC images.
Rich Colors results in an image with deep contrast and saturated
vibrant colors. It is generally used under bright lighting conditions.
This setting works well to enhance colors of certain graphics and it
may be useful when images created for a MACINTOSH are displayed
from a PC.
Spreadsheets results in an image with contrast between a PC and
MACINTOSH monitor. It is generally used for text-rich tables, such
as financial displays. This setting factors in ambient light, subject
matter, and personal preferences to deliver the right balance of
contrast and brightness.
Graphics delivers the maximum brightness and high contrast needed
to project graphics and text against solid colored backgrounds.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Using the Image Manager
1. Click the Kodak menu.
2. Select the setting best suited for your presentation material and
environment.
The new contrast setting is immediately applied to the image.
3. Click OK to save the setting as your default Image Manager
setting for the current and future presentations.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance &
Troubleshooting
This section describes how to:
•
•
•
•
•
clean the lens
replace the projection lamp
replace the batteries in the remote
use the Kensington lock feature
troubleshoot the projector
Cleaning the Lens
Follow these steps to clean the projection lens:
1. Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
•
•
Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might
scratch the lens.
2. Lightly wipe the cleaning cloth over the lens in a circular motion.
3. If you don’t intend to use the projector immediately, replace the
lens cap.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Replacing the Projection Lamp
&DXWLRQꢀ 7RꢁDYRLGꢁEXUQVꢂꢁDOORZꢁWKHꢁSURMHFWRUꢁWRꢁFRROꢁIRUꢁDWꢁOHDVWꢁꢄꢅꢁ
PLQXWHVꢁEHIRUHꢁ\RXꢁRSHQꢁWKHꢁODPSꢁPRGXOHꢁGRRUꢃꢁ1HYHUꢁ
H[WUDFWꢁWKHꢁODPSꢁPRGXOHꢁZKLOHꢁWKHꢁODPSꢁLVꢁRSHUDWLQJꢃ
The lamp hour counter in the Status menu counts the number of hours
the lamp has been in use. Replace the lamp when the brightness is no
longer acceptable. You can order new lamp modules from your dealer
of KODAK products.
Follow these steps to replace the projection lamp:
1. Turn off the projector by unplugging the power cord.
2. Wait 30 minutes to allow the lamp to cool thoroughly.
3. Invert the projector on a flat surface, then insert a small
screwdriver or other flat object into the tab on the lamp module
door.
4. Pull the lamp door up and remove it.
&DXWLRQꢀꢁ 1HYHUꢁRSHUDWHꢁWKHꢁSURMHFWRUꢁZLWKꢁWKHꢁODPSꢁGRRUꢁRSHQꢁRUꢁ
UHPRYHGꢃꢁ7KLVꢁGLVUXSWVꢁWKHꢁDLUꢁIORZꢁDQGꢁFDXVHVꢁWKHꢁ
SURMHFWRUꢁWRꢁRYHUKHDWꢃ
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Troubleshooting
5. Loosen the two non-removable screws on the outside of the
module.
6. Grasp the pull tab and lift out the lamp module.
Be careful when removing the lamp module so that it does not
break.
7. Install the new lamp module, being sure to align the connectors
properly.
&DXWLRQꢀ 'RꢁQRWꢁGURSꢁWKHꢁODPSꢁPRGXOHꢁRUꢁWRXFKꢁWKHꢁJODVVꢁEXOEꢆꢁ
7KHꢁJODVVꢁPD\ꢁVKDWWHUꢁDQGꢁFDXVHꢁLQMXU\ꢃ
39
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
8. Gently push the module in until it is flush with the bottom
case of the projector.
9. Tighten the screws on the outside of the module.
ꢃꢄꢁ 5HSODFHꢀWKHꢀODPSꢀGRRUꢀE\ꢀLQVHUWLQJꢀWKHꢀKRRNVꢀRQꢀWKHꢀUHDUꢀRIꢀWKHꢀ
ODPSꢀGRRUꢀLQWRꢀWKHꢀSURMHFWRUꢀDQGꢀSUHVVLQJꢀWKHꢀODPSꢀGRRUꢀLQWRꢀ
SODFHꢁ
ꢃꢃꢁ 3OXJꢀLQꢀWKHꢀSRZHUꢀFRUGꢀWRꢀWXUQꢀWKHꢀSURMHFWRUꢀEDFNꢀRQꢁ
ꢃꢅꢁ 7RꢀUHVHWꢀWKHꢀODPSꢀKRXUꢀFRXQWHUꢀLQꢀWKHꢀ6WDWXVꢀZLQGRZꢂꢀSUHVVꢀDQGꢀ
KROGꢀWKHꢀ ꢀEXWWRQꢂꢀWKHQꢀSUHVVꢀWKH
EXWWRQꢀꢆZKLOHꢀVWLOOꢀ
KROGLQJꢀGRZQꢀWKHꢀ EXWWRQꢇꢀIRUꢀꢈꢀVHFRQGVꢁꢀ9HULI\ꢀWKDWꢀWKHꢀ
FRXQWHUꢀZDVꢀUHVHWꢀE\ꢀSUHVVLQJꢀWKHꢀ
FRXQWHUꢀLQꢀWKHꢀ6WDWXVꢀZLQGRZꢁ
ꢀEXWWRQꢀDQGꢀYLHZLQJꢀWKHꢀ
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Troubleshooting
Replacing the Batteries in the Remote
Control
The life of the batteries depends on how often and how long you use
the remote control. Symptoms of low battery charge include erratic
responses when using the remote control and a reduced range of
operation.
Follow these steps to replace the batteries:
1. Turn the remote control face down in your hand.
2. Slide the battery cover off the end of the remote control.
3. Remove the old batteries and properly dispose of them.
4. Install two new AAA alkaline batteries. Make sure you install
each battery in the correct direction.
5. Slide the battery cover back on the remote control.
Using the Kensington Lock
The projector has a Kensington Security Standard connector for use
with a Kensington MicroSaver Security System. Refer to the
information that came with the Kensington System for instructions on
how to use it to secure the projector.
DLP
A
T
E
X
A
S
I
N
S
T
R
U
M
E
N
T
S
TECHNOLOGY
Includes
Image Manager
41
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Troubleshooting
Problem: Nothing on projection screen
• Make sure that the power cord is properly connected to a
fully functional AC electrical outlet. Make sure that the
power cord is also properly connected to the projector.
• If the projector is plugged into a power strip, make sure the
power strip is turned on.
• Make sure you have removed the lens cap on the projection
lens at the front of the projector.
• Make sure the lamp is switched on.
• Check the projector’s lamp to ensure that it is securely
connected in the lamp module. See “Replacing the
Projection Lamp” on page 38.
• Make sure that the cables do not have any bent pins.
Problem: Color or text not being projected
• You might need to adjust the brightness up or down until
the text is visible. Refer to “Brightness” on page 26 for
more information.
Problem: The screen resolution is not right
• Make sure the computer’s video card is set for a resolution
of no greater than 1024 x 768.
Problem: Image isn’t centered on the screen
• Move the projector to reposition the image.
• Reposition the image using the software. Refer to
“Horizontal position” on page 29 and “Vertical position”
on page 30.
• Be sure the projector is at a 90 degree angle to the screen.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Troubleshooting
Problem: Only the start-up screen displays
• Verify that the cables are connected correctly. See page 12
through page 16 for connection procedures.
• Verify that the proper input source is selected. See “Source
(keypad only) or Computer and Video (remote control
only)” on page 24.
• You might need to turn everything off and turn on the
equipment again in the proper order. Refer to your
computer documentation to determine the correct order.
• Make sure your laptop external video port is turned on. See
the “Portable and Laptop Activation Chart” on page 49 in
this guide or your computer’s manual for details.
• Make sure your computer video board is installed and
configured correctly.
• Make sure your computer has a compatible video board.
The projector isn’t CGA, EGA or SXGA compatible.
If you’re using Windows 98:
1. Open "My Computer" icon, the Control Panel folder and then the
Display icon.
2. Click the Settings tab.
3. Verify that the Desktop area is set to 1024 x 768 or less.
Problem: Image is too wide or narrow for screen
• Adjust the zoom or projector placement.
• Adjust the resolution of your video card if it’s greater than
1024 x 768.
Problem: Image is out of focus
• Turn the projection lens to focus the image.
• Make sure the projection screen is at least 5 feet
(1.5 m) from the projector.
• Check the projection lens to see if it needs cleaning.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Problem: Image and menus are reversed left to
right
• Rear projection mode is probably turned on. Turn Rear
Projection off in the Controls menu. The image should
immediately return to forward projection. See “Rear
Projection” on page 31.
Problem: the projector displays vertical lines,
“bleeding” or spots
• Adjust the brightness. See “Brightness” on page 26.
• Check the projection lens to see if it needs cleaning.
Problem: no sound
• Adjust the volume.
• Verify the audio/input connections.
• Adjust the audio source.
Problem: Image is “noisy” or streaked
Try these steps in this order.
1. Deactivate the screen saver on your computer.
2. Turn Auto Image off and then back on again. See “Auto Image” on
page 28.
3. Turn Auto Image off and adjust the synchronization and tracking
manually to find an optimal setting. See “Manual Sync” on
page 29 and “Manual Tracking” on page 29.
• The problem could be with your computer’s video card. If
possible, connect a different computer.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Troubleshooting
Problem: Projected colors don’t match the
computer or video player’s colors
Just as there are differences in the displays of different monitors, there
are often differences between the computer image and the projected
image.
• Adjust the colors using the KODAK Image Manager. See
“Kodak Menu” on page 35.
• Adjust the brightness, tint and/or contrast from the Display
menu. See “Brightness” on page 26, “Tint” on page 27 and
“Contrast” on page 26.
Problem: Lamp seems to be getting dimmer
• The lamp begins to lose brightness when it has been in use
for a long time. Replace the lamp as described in
“Replacing the Projection Lamp” on page 38.
Problem: Lamp shuts off
• A minor power surge may cause the lamp to shut off.
Unplug the projector, wait at least a minute, then plug it
back in.
• Make sure the vents are not blocked.
To contact KODAK support see “If You Need Assistance” on
page 8.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
The projectors must be operated and stored within the temperature
and humidity ranges specified.
Temperature
Operating
50 to 104° F (10 to 40° C)
Non-operating
-4 to 158° F (-20 to 70° C)
Humidity
Operating and non-operating 5% to 95% relative humidity,
non-condensing
Dimensions
8.9 x 10 x 2.8 inches (22.6 x 25.4 x 7.1 cm)
Weight
4.8 lbs (2.2 kg) unpacked
Altitude
Operating
0 to 10,000 feet (3,048 meters)
0 to 40,000 feet (12,192 meters)
Non-operating
9/99
47
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Optics
Focus Range
4.9 - 16 feet (1.5 - 5 m)
120-watt VIP lamp
Lamp
Type
Input Power Requirements
100-120VAC 6A; 50/60Hz
200 - 240VAC 3A; 50Hz
Audio Input
Input Impedance
10K ohm nominal, AC coupled
Maximum Input Voltage
(L + R )
< 4.5 V for
IN
IN PEAK
THD ≤ 0.3%
L
or R < 2.0 Vrms for THD
IN
IN
≤ 0.3%
Sensitivity
100 mV at 1 KHz for 88 dB
SPL at 1 meter
Connector Type
3.5 mm (1/8 inch) stereo phone
mini
48
9/99
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Portable and Laptop Activation Chart
Many laptop computers do not automatically turn on their external
video port when a secondary display device such as a projector is
connected. Activation commands for some laptop computers are
listed in the following table. (If your computer is not listed or the
given command does not work, refer to the computer’s
documentation for the appropriate command.) On many laptops, the
activation function key is labeled with an icon, for example
or the text CRT/LCD.
Note: Usually, pressing the key commands once activates the
external video port, pressing it again activates both the
external and internal ports, and pressing it a third time
activates the internal port. Refer to your computer
documentation for details on your specific model.
Key command
Key command
to
Computer
to
de-activate
port
activate port
Acer
Ctrl-Alt-Esc (for
setup)
Ctrl-Alt-Esc (for
setup)
AST* **
FN-D or Ctrl-D
Ctrl-FN-D
FN-F5
FN-D or Ctrl-D
Ctrl-FN-D
FN-F5
type from A:/IVGA/
CRT
type from A:/IVGA/
CRT
FN-F12
FN-F12
49
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Key command
to
Key command
to
activate port
Computer
de-activate
port
AMS
AMT
AT&T
FN-F2
FN-F2
setup screen
setup screen
FN-F3
FN-F6
FN-F3
FN-F6
Advanced
Logic
Ctrl-Alt-V
Ctrl-Alt-V
Research
Altima
Shift-Ctrl-Alt-C
Shift-Ctrl-Alt-L
setup VGA/
setup VGA/
Conf.Simulscan
Conf.Simulscan
Ambra**
FN-F12
FN-F5
FN-F12
FN-F5
F2/Choose Option/
F5
F2/Choose Option/
F5
Amrel* **
setup menu
Shift-Ctrl-D
setup menu
Shift-Ctrl-D
Apple
Aspen
Award
see Mac Portable and Mac PowerBook
automatic
FN-F6
automatic
FN-F6
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Key command
to
Key command
to
activate port
Computer
de-activate
port
BCC*
automatic
reboot computer
Bondwell
LCD or CRT
options after bootup
reboot for LCD or
CRT options to
appear
Chaplet**
setup screen
FN-F6
setup screen
FN-F6
FN-F4
FN-F4
Chembook
Commax
FN-F6
FN-F6
Ctrl-Alt-#6
Ctrl-Alt-<
FN-F4
Ctrl-Alt-#5
Ctrl-Alt->
FN-F4
Compaq* **
automatic
automatic
mode/? (for setup
option)
mode/? (for setup
option)
Compuadd*
**
automatic
automatic
Alt-F for screen
setup option
Alt-F for screen
setup option
Data General
Ctrl-Alt-Command
Ctrl-Alt-Command
51
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Key command
to
Key command
to
activate port
Computer
de-activate
port
Data General
Walkabout
2 CRT/X at DOS
prompt
reboot
Datavue
DEC**
Ctrl-Shift-M
FN-F5
Ctrl-Shift-M
FN-F5
FN-F4
FN-F4
Dell**
Ctrl-Alt-<
Ctrl-Alt->
Ctrl-Alt-F10
FN-F8
Ctrl-Alt-F10
FN-F8 (CRT/LCD)
FN-D
FN-D
FN-F12
FN-F12
Digital*
automatic
reboot
FN-F2
FN-F2
Dolch
dip switch to CRT
dip switch to CRT
setup screen option
Ctrl-Alt-Shift-C
FN-F10
dip switch to LCD
dip switch to LCD
setup screen option
Ctrl-Shift-Alt-L
Epson
Everex*
For-A
Fujitsu
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Key command
to
Key command
to
activate port
Computer
de-activate
port
Gateway
FN-F3
FN-F3
FN-F1
FN-F1/FN-F1 again
simultaneous
Grid* **
FN-F2, choose auto
or simultaneous
FN-F2
Ctrl-Alt-Tab
FN-F7
Ctrl-Alt-Tab
FN-F7
Hitachi
Honeywell
Hyundai
IBM 970*
FN-F10
FN-F10
setup screen option
automatic
setup screen option
warm reboot
FN-F2
IBM
ThinkPad**
reboot, enter setup
menu
FN-F7, select
choice from setup
menu
FN-F1, select
choice
FN-F5, select
choice
53
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Key command
to
Key command
to
activate port
Computer
de-activate
port
PS/2 SC select
choice (CRT, LCD,
etc.)
Infotel
FN-F12
FN-F12
Kaypro
boot up, monitor
plugged in
unplug monitor
Kris Tech
FN-F8
FN-T
FN-F8
FN-T
Leading Edge
Mac Portable
100
no video port: not compatible
Mac
PowerBook
140, 145, 150,
170
no video port: requires a 3rd-party interface
160, 165,
180, 520, 540,
5300
Control Panel
folder, PowerBook
Display folder;
Activate Video
Mirroring
warm reboot
210, 230,250,
270, 280,
2300
requires Apple Docking Station or Mini
Dock
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Key command
to
Key command
to
activate port
Computer
de-activate
port
Magitronic
Mastersport
FN-F4
FN-F4
FN-F2
FN-F1
Micro
automatic
warm reboot
Express*
Micron
FN-F2
FN-F2
Microslate*
Mitsubishi
automatic
warm reboot
SW2 On-Off-Off-
Off
SW2 Off-On-On-
On
NCR
setup screen option
setup screen option
setup screen option
setup screen option
NEC* **
CRT at the DOS
prompt
LCD at the DOS
prompt
FN-F3
FN-F3
Olivetti*
automatic
FN-O/*
FN-F0
automatic
FN-O/*
FN-F0
Packard Bell*
**
Ctrl-Alt-<
Ctrl-Alt->
55
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Key command
to
Key command
to
activate port
Computer
de-activate
port
Panasonic
Prostar
FN-F2
FN-F2
Ctrl-Alt-S at bootup
setup screen option
setup screen option
dip switch to CRT
Ctrl-Shift-M
Ctrl-Alt-S at bootup
setup screen option
setup screen option
dip switch to LCD
Ctrl-Shift-M
Samsung*
Sanyo
Sharp
Sun SPARC-
Dataview
Tandy**
Ctrl-Alt-Insert
setup screen option
FN-F5
Ctrl-Alt-Insert
setup screen option
FN-F5
Tangent
Texas
setup screen option
setup screen option
Instruments*
Top-Link* **
Toshiba* **
setup screen option
FN-F6
setup screen option
FN-F6
Ctrl-Alt-End
FN-End
Ctrl-Alt-Home
FN-Home
FN-F5
FN-F5
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Key command
Key command
to
activate port
to
Computer
de-activate
port
setup screen option
FN-F7
setup screen option
FN-F7
Twinhead*
FN-F5
FN-F5
Automatic
Ctrl-Alt-F10
software driven
FN-F10
Automatic
Ctrl-Alt-F10
software driven
FN-F10
WinBook
Wyse
Zenith**
FN-F2
FN-F2
FN-F1
FN-F1
Zeos**
Ctrl-Shift-D
FN-F1
Ctrl-Shift-D
FN-F1
*
These manufacturers have models that automatically send video to the external CRT
port when some type of display device is attached.
** These manufacturers offer more than one key command depending on the computer
model
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Using Video Mirroring with a PowerBook
Computer
When you turn video mirroring (called SimulScan in newer
PowerBooks-see below) on, the projector displays the same
information that appears on your PowerBook’s built-in screen. When
video mirroring is off, the projector acts like a separate display.
To turn on video mirroring for the first time:
1. Open the Monitor’s control panel; click on Monitor 2.
2. Set the number of colors you want.
3. Open the Control Strip; click on the monitor icon.
4. Select “Turn Video Mirroring On.”
Now you can turn video mirroring on and off from the Control Strip
without having to open the Monitor’s control panel again.
When using video mirroring and high color graphics such as slide
shows, the projected image occasionally might turn black and white.
If this happens, perform the following steps:
1. Turn off video mirroring.
2. Open the Monitor’s control panel.
3. Move the white menu bar to Monitor 2 to set the projector as the
primary monitor.
4. Restart the PowerBook.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Using SimulScan
Some newer PowerBooks display images on an external monitor or
projector differently than previous ones. When using SimulScan, the
projector displays the same information that appears on your
PowerBook.
To select SimulScan:
1. Open the Control Panel, then double-click Monitors and Sound.
2. In the Resolution list, choose the SimulScan mode, then click
OK.
3. If this changes your display settings, a dialog box appears. Click
OK to confirm the change.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D
Projected Image Size
Use this chart and tables to help you determine projected image sizes
61
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
Table 1:
Image Size, Width and Height for DP2000-maximum image size
Distance to
Screen
Diagonal
Width
Height
4.9 ft
1.5 m
3.2 ft
.9 m
2.6 ft
.8 m
1.9 ft
6 m
8 ft
2.4 m
5.2 ft
1.6 m
4.2 f
1.3 m
3.1 ft
.9 m
12 ft
3.7 m
7.8 ft
2.4 m
6.3 ft
1.9 m
4.7 ft
1.4 m
16 ft
4.9 m
10.4 ft
3.1 m
8.3 ft
2.5 m
6.3 ft
1.9 m
20 ft
6 m
13.0 ft
3.9 m
10.4 ft
3.1 m
7.8 ft
2.4 m
30 ft
9 m
19.5 ft
5.9 m
15.6 ft
4.8 m
11.7 ft
3.6 m
Table 2:
Image Size, Width and Height for DP2000-minimum image size
Distance to
Screen
Diagonal
Width
Height
4.9 ft
1.5 m
2.5 ft
.8 m
2.0 ft
.6 m
1.5 ft
.4 m
8 ft
2.4 m
4.1 ft
1.25 m
3.3 ft
1 m
2.5 ft
.7 m
12 ft
3.7 m
6.2 ft
1.9 m
4.9 ft
1.5 m
3.7 ft
1.1 m
16 ft
4.9 m
8.2 ft
2.5 m
6.6 ft
1.9 m
4.9 ft
1.5 m
20 ft
6 m
10.3 ft
3.1 m
8.2 ft
2.5 m
6.2 ft
1.9 m
30 ft
9 m
15.4 ft
4.7
12.3 ft
3.7 m
9.2 ft
2.8 m
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
not displayed 42
compatibility
activation commands for laptops 49
adjusting
IBM-compatible 5
Macintosh 5
brightness 26
color 27
contrast 26
composite video cable
connecting 15
height 20
tint 27
computers, compatible 5
connecting
volume 24, 27
altitude limits 47
assistance. See Technical Support
Audio menu 27
Volume 27
laptop 14
mouse 14
power cord 17
video player 15–16
connector panel 12
contrast, adjusting 26
Controls menu 30
Auto Source Select 31
Default Source 31
Display Messages 32
Display Startup Screen 32
Plug and Play 32
Rear Projection 31
Standby Time 31
Video Standard 30
customer support numbers 9
Auto Source Select 31
B
Blank Screen 27
brightness, adjusting 26
buttons on keypad
Menu 24
Standby 24
Volume 24
C
cable hub 12
cables
D
A/V 15
Default Source 31
dimensions 47
Display menu options
Blank Screen 27
Brightness 26
Color 27
composite video 15
hub connector 12
mouse 14
cleaning the projection lens 37
color
adjusting 27
colors
Contrast 26
Reset All 27
Tint 27
don’t match monitor colors 45
63
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Guide KODAK DP2000 Digital Projector
displaying
Auto Resize 28
messages 32
on-screen menus 24
startup screen 32
Horiz. Position 29
Manual Sync 29
Manual Tracking 29
Vert. Position 30
F
focus range 48
fuzzy lines 29
K
Kensington lock 41
keypad
H
help
using 23
keypad buttons
menu 24
customer support numbers 9
fax 8
humidity 47
standby 24
volume 24
KODAK Image Manager 35
I
IBM-compatible computers
compatibility 5
image
L
lamp
turns off unexpectedly 45
lamp hour counter 34
Language menu 33
language, selecting for menus 33
laptop activation sequence 49
lens
adjusting 19
centering 29
colors don’t match 45
fuzzy lines 29
has lines or spots 44
not centered 42
not displayed 42
out of focus 43
quality 42–45
cleaning 37
M
Macintosh computers
compatibility 5
resolution 5
reversed 31, 44
size 11, 61
streaked 44
too wide or too narrow 43
zooming 20
Menu button 25
menus. See on-screen menus
monitor, colors don’t match 45
mouse, connecting 14
N
Image Manager 35
Image menu options 28
Auto Image 28
NTSC video 30
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
O
specifications 47
Standby button 24
Standby Time 31
startup screen 32
Status menu 33
on-screen menus
Audio menu 27
changing functions 25
changing language of 33
Controls menu 30
Display menu 26
displaying 25
support numbers 9
S-video, connecting 15
T
Image menu 28
Language menu 33
Status menu 33
temperature limits 47
test pattern 43
text not visible 42
tint, adjusting 27
turning off the projector 18
turning on the projector 17
P
PAL video 27, 30
Plug and Play 32
power cord
U
connecting 17
USB mouse 14
power up sequence 17, 43
project from behind the screen 31
V
vertical lines displayed 29, 44
video 27
mirroring PowerBook 59
video standards 30
volume
R
rear projection 31
relative humidity 47
remote control
operating the disk mouse 22
using 21, 23
adjusting 24
re-positioning image on screen 29
resetting adjustments 27
resolution 5
W
warranty 10, 67
weight 47
S
Z
safety guidelines 1
SECAM video 27, 30
security feature 41
service numbers 9
setting up 11
zooming the image 20
SimulScan with PowerBooks 60
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY TIME PERIOD
Kodak warrants the KODAK DIGITAL SCIENCE DP2000 Digital Projector (excluding lamps) to be free
from malfunctions and defects in both materials and workmanship for two years from the date of purchase.
WARRANTY REPAIR COVERAGE
This warranty will be honored within the geographical location that the product was purchased.
If the equipment does not function properly during the warranty period due to defects in either materials
or workmanship, Kodak will, at its option, either repair or replace the equipment without charge, subject to
the conditions and limitations stated herein. Such repair will include all labor as well as any necessary
adjustments and/ or replacement parts.
If replacement parts are used in making repairs, these parts may be remanufactured, or may contain reman-
ufactured materials. If it is necessary to replace the entire system, it may be replaced with a remanufactured
system.
Kodak will also provide telephone assistance during the warranty period.
LIMITATIONS
WARRANTY SERVICE WILL NOT BE PROVIDED WITHOUT DATED PROOF OF PURCHASE.
THIS WARRANTY BECOMES NULL AND VOID IF YOU FAIL TO PACK YOUR DIGITAL PROJECTOR
IN A MANNER CONSISTENT WITH THE ORIGINAL PRODUCT PACKAGING AND DAMAGE
OCCURS DURING PRODUCT SHIPMENT.
THIS WARRANTY DOES NOT COVER: CIRCUMSTANCES BEYOND KODAK’S CONTROL; SERVICES
OR PARTS TO CORRECT PROBLEMS RESULTING FROM THE USE OF ATTACHMENTS, ACCESSO-
RIES, OR ALTERATIONS NOT MARKETED BY KODAK; SERVICE REQUIRED AS THE RESULT OF
UNAUTHORIZED MODIFICATIONS OR SERVICE; MISUSE, ABUSE; FAILURE TO FOLLOW KODAK’S
OPERATING, MAINTENANCE, OR REPACKAGING INSTRUCTIONS; OR FAILURE TO USE ITEMS
SUPPLIED BY KODAK (SUCH AS ADAPTORS AND CABLES).
KODAK MAKES NO OTHER WARRANTIES, EXPRESS, IMPLIED, OR OF MERCHANTABILITY OR FIT-
NESS FOR A PARTICULAR PURPOSE FOR THIS EQUIPMENT OR SOFTWARE.
REPAIR OR REPLACEMENT WITHOUT CHARGE ARE KODAK’S ONLY OBLIGATION UNDER THIS
WARRANTY. KODAK WILL NOT BE RESPONSIBLE FOR ANY SPECIAL, CONSEQUENTIAL OR INCI-
DENTAL DAMAGES RESULTING FROM THE PURCHASE, USE, OR IMPROPER FUNCTIONING OF
THIS EQUIPMENT REGARDLESS OF THE CAUSE. SUCH DAMAGES FOR WHICH KODAK WILL NOT
BE RESPONSIBLE INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF REVENUE OR PROFIT, DOWN-
TIME COSTS, LOSS OF USE OF THE EQUIPMENT, COST OF ANY SUBSTITUTE EQUIPMENT, FACILI-
TIES OR SERVICES, OR CLAIMS OF YOUR CUSTOMERS FOR SUCH DAMAGES.
Depending on your geographical location, some limitations and exclusions may not apply.
Shipment of a unit from the customer to the kodak service center will be at the customer’s expense.
This warranty is not transferable from the original purchaser of the equipment.
APPLICATION SUPPORT
For application specific support, contact your reseller, systems integrator, software manufacturer, or dealer.
9/99
67
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO OBTAIN SERVICE
Please refer to the Service and Support section of your User’s Guide for the support hotline designated to your location.
When returning a digital projector for repair, the unit shall be packed in its original packing materials. A problem report
should also be enclosed with the equipment. If the original packaging has been discarded or is not available, packing will
be at the owner’s expense.
The repaired or replaced unit will be shipped from Kodak within five business days from the date of the digital projector
receipt at the service center.
Unless a specific Kodak warranty is communicated to the purchaser in writing by a Kodak company, no other warranty or
liability exists beyond the information contained above, even though defect, damage, or loss may be caused by negligence
or other act.
To obtain warranty repair service contact your local Kodak representative. For assistance, refer to the Service and Support
information in the KODAK Digital Projector User ’s Guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Eastman Kodak Company
343 State Street
Rochester, New York 14650
Kodak is a trademark of
Eastman Kodak Company.
PN 3H7969
9/99
©Eastman Kodak Company
Printed in the U.S.A.
PN 010-0219-00
Download from Www.Somanuals.com. All Manuals Search And Download.
|