®
Single Drawer Dishwasher
PRODUCT MODEL SERIES
OVERALL DIMENSIONS
KUDD01SS
22⁷⁄₁₆"
*
23⁷⁄₁₆"
(59.5 cm)
(57 cm)
Electrical: 120-volt, 60 Hz, AC-only, 15 or
20 amp fused electrical supply is required. A
time-delay fuse or circuit breaker and separate
circuit is recommended.
16³⁄₃₂"
Water: A hot water line with 4.3-145 psi
(30-1000 kPa) water pressure. Water temperature
must be minimum 120°F (49°C) at dishwasher. An
easily accessible valve with ³⁄₈” compression
fitting must be installed in the hot water supply
line.
side
attaching
tabs
20¹⁵⁄₃₂"
(52 cm)
drawer open
* If custom wood panels are to be used, the product depth is specified
with an ¹¹⁄₁₆" (18 mm) door panel thickness.
NOTE: Product shown with front panels for dimension purposes.
CABINET DIMENSIONS
moisture protection
tape
4"
(10 cm)
19⁷⁄₈"
(50.5 cm)
Utility hole:
1¹⁄₂" (3.8 cm) dia.
hole, either side –
immediately adjacent
to corner.
16 ⁷⁄₃₂"
(41.2 cm)
3¹³⁄₁₆"
(9.7 cm)
2
⁵⁄₈"
(6.7 cm)
22⁷⁄₈" (58.0 cm)
23⁵⁄₈"* (60.0 cm)
support surface must
be solid and level
These marks indicate the mounting tab screw locations.
Minimum thickness of cabinet/cavity sides – ⁵⁄₈" (1.6 cm)
Install the dishwasher in a cabinet cutout that is level, will hold weight
up to 104lbs. (47kg), and is in an area suitable for its size and use.
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 8573714
02-03-06
Download from Www.Somanuals.com. All Manuals Search And Download.
®
KitchenAid Single Drawer Dishwasher Custom Door Panel Requirements
MODEL: KUDD01SSPA
9”
(22.9 cm)
3) On the front side of the custom door panel, measure,
mark and cut a hole for the medallion to size as shown
2 5⁄16”
(5.9 cm)
(See figures 1 & 2).
NOTE: The medallion must be placed within the specified
medallion area. Do not locate outside of this specified area
(See figure 1).
CUSTOM
PANEL
(Front Side)
5”
(12.7 cm)
4) Lay the custom door panel face down on a protective surface
to prevent damage or abrasions.
Medallion
Location Area
Center of
Custom Panel
5) On the backside of the custom door panel, rout a
1
⁄4” (6.4 mm) radius around the medallion cutout previously
cut in step #3. The medallion end does not need to
be routed.
23 7⁄16”
(59.5 cm)
6) If custom door panel material is not suitable to withstand
damp conditions, seal with a moisture resistant material.
For painted panel, paint all rear edges to improve sealing.
FIGURE 1
Horizontal
Position Line
MEDALLION CUTOUT DIMENSIONS
1 9⁄32” (32.6mm) MAX.
1 7⁄16”
(36.5 mm)
CUSTOM
PANEL
(Back Side)
17⁄32”
(30.8 mm)
1
⁄4”
(6.4 mm)
Medallion
Location Area
Vertical
Center Line
1 13⁄64”
(30.6 mm)
Medallion
End
2 13⁄32”
(60.8 mm)
FIGURE 3
FIGURE 2
7) On the backside of the custom door panel, measure and
mark the vertical center line and horizontal position line
(See figure 3).
IMPORTANT: It is recommended that the custom door panel
be made from suitable material to withstand damp conditions
or adequately sealed with a moisture-resistant material to
withstand moisture and humidity.
NOTE: The 1 7⁄16” (36.5 mm) horizontal position line is
marked for later use in the installation process. Refer to the
Installation Instructions Single Drawer Dishwasher included
with the Drawer Dishwasher to align and attach the custom
door panel to the factory supplied metal plate.
1) Cut the custom door panel to size as shown
(See figure 1). The custom panel may be wider than
the dishwasher in order to match the surrounding cabinets.
NOTE: The minimum custom panel thickness is
5
⁄
8” (16mm). Panel thickness more than 11⁄16” (18mm)
8) Mount the customer supplied handle to the location
previously marked on the custom panel.
can be accommodated but overall product depth will
increase accordingly.
IMPORTANT: When mounting the customer supplied
handle, screws must fit flush to the panel and not extend
beyond the back surface.
2) On the front side of the custom door panel, measure and mark
the location of the customer supplied handle. The location is
customer preference. Do not install handle at this time.
9) Refer to the Installation Instructions Single Drawer
Dishwasher included with the Drawer Dishwasher
to complete installation.
Download from Www.Somanuals.com. All Manuals Search And Download.
|