DVD / HDD & Mini DV VIDEO RECORDER
SR-DVM70US
CABLE/DBS
TV
DVD
STANDBY/ON
DVD
TV/
VIDEO TV/CBL/DBS
HDD
DV
DVD
TV VOL
CH
CANCEL
LIVE
AUX
MEMO/MARK
EDIT
DUBBING
PROG
TV MUTING
TOP MENU
MENU
NAVIGATION
RETURN
ENTER
PREVIOUS
SLOW
NEXT
SLOW
PLAY/SELECT
CLEAR
STOP/
REC
PAUSE
NTSC
JUMP
OPERATE
DISPLAY
REC MODE
REMAIN
DISPLAY
ON SCREEN
SET UP
EJECT
EJECT
DV/HDD/DVD
STOP
REC MODE
INSTANT REPLAY
AUDIO DUB.
REC
INSERT
DV
REC
HDD
REC
DVD
REC
S-VIDEO
VIDEO (MONO)L
-
AUDIO
-
R
REW
PLAY
FF
PAUSE
CH
DV IN/ OUT
IN F-1
For Customer Use:
Enter below the Model No. and Serial
No. which are located on the rear of
cabinet. Retain this information for
future reference.
Model No.
Serial No.
INSTRUCTIONS
EN
LPT1006-001B
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
EN
3
ANTENNA INSTALLATION INSTRUCTIONS
1. Outdoor Antenna Grounding
IMPORTANT PRODUCT SAFETY
INSTRUCTIONS
If an outside antenna or cable system is connected to the product,
be sure the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding connectors, location of
antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
Electrical energy can perform many useful functions. But improper
use can result in potential electrical shock or fire hazards. This
product has been engineered and manufactured to assure your
personal safety. In order not to defeat the built-in safeguards,
observe the following basic rules for its installation, use and
servicing.
ATTENTION:
2. Lightning
Follow and obey all warnings and instructions marked on your
product and its operating instructions. For your safety, please read
all the safety and operating instructions before you operate this
product and keep this booklet for future reference.
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning
and power-line surges.
INSTALLATION
1. Grounding or Polarization
3. Power Lines
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them
might be fatal.
(A)Your product may be equipped with a polarized alternating-
current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a
safety feature.
If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
(B)Your product may be equipped with a 3-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.
2. Power Sources
Operate your product only from the type of power source indicated
on the marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or local power
company. If your product is intended to operate from battery
power, or other sources, refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
5. Ventilation
Slots and openings in the cabinet are provided for ventilation. To
ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered.
● Do not block the openings by placing the product on a bed, sofa,
rug or other similar surface.
● Do not place the product in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
4
EN
USE
SERVICING
1. Servicing
1. Accessories
To avoid personal injury:
If your product is not operating correctly or exhibits a marked
change in performance and you are unable to restore normal
operation by following the detailed procedure in its operating
instructions, do not attempt to service it yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
● Do not place this product on an unstable cart, stand, tripod,
bracket, or table. It may fall, causing serious injury to a child or
adult, and serious damage to the product.
● Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the product.
● Use a mounting accessory recommended by the manufacturer
and follow the manufacturer’s instructions for any mounting of
the product.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore
the product to its normal operation.
● Do not try to roll a cart with small casters across thresholds or
deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
3. Water and Moisture
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
Do not use this product near water—for
example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet
basement, or near a swimming pool and the like.
3. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or which have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
4. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short-
out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
4. Safety Check
5. Attachments
Upon completion of any service or repairs to this product, ask
the service technician to perform safety checks to determine
that the product is in safe operating condition.
Do not use attachments not recommended by the manufacturer
of this product as they may cause hazards.
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
HOW TO USE THIS INSTRUCTION MANUAL
● All major sections and subsections are listed in the Table Of
Contents on page 6. Use this when searching for information on
a specific procedure or feature.
● The Index on pages 12 - 15 illustrates the controls and
connections on the front and rear panel, the front display panel
and the remote control.
7. Heat
The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
● The list of terms on page 89 lists frequently-used terms, and the
number of the page on which they are used or explained in the
manual.
● The A mark signals a reference to another page for instructions
or related information.
● Operation buttons necessary for the various procedures are
clearly indicated through the use of illustrations at the beginning
of each major section.
BEFORE YOU INSTALL YOUR NEW UNIT . . .
. . . please read the sections/literature listed below.
● ACautionsB on page 2
● AIMPORTANT PRODUCT SAFETY INSTRUCTIONSB on
pages 3 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
EN
5
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
Declaration of Conformity
Model Number:
Trade Name:
SR-DVM70US
JVC
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the unit, remote control or disc/cassette.
1. DO NOT place the unit ^
^ in an environment prone to extreme temperatures or
humidity.
^ in direct sunlight.
^ in a dusty environment.
^ in an environment where strong magnetic fields are
generated.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
^ on a surface that is unstable or subject to vibration.
2. DO NOT block the unit’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the unit or remote control.
4. DO NOT place anything which might spill on top of the unit
or remote control.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with
water. Also DO NOT place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases, potted
plants, cups, etc.) on top of this unit.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the unit when you move it from
a cold place to a warm place, or under extremely humid
conditions^just as water droplets form on the surface of a glass
filled with cold liquid. In conditions where condensation may occur,
disconnect the unit’s power plug from the wall and keep it
disconnected for a few hours to let the moisture dry, then turn on
the unit.
NTSC
● Manufactured under license from Dolby Laboratories. ADolbyB
and double-D symbol are trademarks of Dolby Laboratories.
● ADTSB and ADTS DIGITAL OUTB are trademarks of Digital
Theater Systems, Inc.
● Cassettes marked P can be used with the DV deck of this
unit. The DV deck can play back and record only NTSC signals.
● VCR Plus+ and PlusCode are registered trademarks of Gemstar
Development Corporation.
DISCLAIMER OF LIABILITY
JVC shall not be liable for any loss relating to the unit’s failure to
properly record, store or playback any content (video, audio or
otherwise) for any reason whatsoever. Any applicable warranties
shall only cover replacement or repair of the effected unit, and
shall not apply to recovery or replacement of lost content.
The VCR Plus+ system is manufactured under license from
Gemstar Development Corporation.
TM
● DSS is an official trademark of DIRECTV, Inc., a unit of GM
TM
Hughes Electronics. DISH Network is a trademark of Echostar
Communications Corporation.
ATTENTION:
● This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing users only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
8
8
8
Using a mobile phone in the vicinity of the unit may cause
picture vibration on the TV screen or change the screen to a
blue back display.
Some TVs or other appliances generate strong magnetic
fields. Do not place such appliances on top of the unit as it
may cause picture disturbance.
When moving the product, press A to turn off the power,
and wait at least 30 seconds before unplugging the power
cord. Then, wait at least 2 minutes before moving the
product.
If there is a power outage when using the unit, the recorded
data may be erased.
It is recommended to back up discs which contain important
recordings periodically (every few years). As digital signals
do not deteriorate, failure to play back or record might arise
due to the effects of the disc aging through the years
depending on the storage environment.
8
8
8
Recorded programs and data cannot be restored once the
disc is damaged.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
EN
SAFETY FIRST
2
7
DISC INFORMATION
About Discs....................................................................................7
INDEX
12
DV Dubbing (HDD & DVD Deck Only) ........................................ 60
Insert Editing (DV Deck Only)...................................................... 66
INITIAL SETTINGS
REMOTE CONTROL
67
BASIC OPERATIONS ON DVD DECK
Basic Playback.............................................................................24
Format A Disc (DVD Deck Only) ................................................. 74
Scan Mode Set (HDD & DVD Deck Only) ................................... 76
BASIC OPERATIONS ON HDD DECK
Basic Playback.............................................................................39
BASIC OPERATIONS ON DV DECK
APPENDIX
84
Live Memory Playback.................................................................43
RS-232C INTERFACE
TIMER RECORDING ON HDD/DVD DECK
46
RS-232C Interface – Specifications –.......................................... 84
RS-232C Interface – Command – ............................................... 85
VCR Plus+ Timer Programming...................................................46
Manual Timer Programming.........................................................48
SPECIFICATIONS
LIST OF TERMS
88
89
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
7
DVD-R/RW Discs
It is only possible to use DVD-R discs which conform with DVD-R
standard Version 2.0.
About Discs
When a DVD-R/RW disc (Video mode) is finalized (A pg. 75), it
can be played back on a standard DVD player as a DVD VIDEO
disc.
When a DVD-RW disc (VR mode) is finalized (A pg. 75), it can be
played back on a standard DVD player compatible with the VR
mode of DVD-RW discs.
Recordable/Playable Discs
You can use discs with the following logos for recording and
playback.
Before finalizing ^
^ it is possible to record on unrecorded areas of the disc, edit the
disc title and program titles, and delete programs.
● It is impossible to record or edit DVD-R/RW discs recorded on
other devices even if they have not been finalized.
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
program is deleted from a DVD-R disc.
DVD-RAM
DVD-RW
12 cm: 4.7 GB/9.4 GB
8 cm: 1.4 GB/2.8 GB
Ver. 2.0/2x speed
Ver. 2.1/1x – 3x speed
Ver. 2.2/5x speed
12 cm: 4.7 GB/9.4 GB
Ver. 1.1/1x – 2x speed
(Video mode/VR mode)
Ver. 1.2/4x speed
(Video mode/VR mode)
After finalizing ^
After a DVD-R/RW disc (Video mode) has been finalized, it is
possible to play back the recorded programs (video and/or audio)
on a standard DVD video player as a DVD VIDEO disc.
● Edited titles are displayed as the
ADVD menuB in video mode.
● It is impossible to record, edit or
delete the data either in video
mode or in VR mode.
DVD-R
12 cm: 4.7 GB
8 cm: 1.4 GB
HOME MOVIES
DOCUMENTARIES
TRAVELLING CLIPS
● Either in video mode or in VR
mode, although the disc can be
played back on DVD players from
other manufacturers, sometimes it
may not be possible to play back depending on the disc and
recording conditions.
● It is impossible to record on CD-R/RW or DVD-R discs used for
authoring.
● It is impossible to record onto DVD-R/RW (Video mode) discs
broadcasts that allow you to copy once. The copy once programs
can only be recorded onto DVD-RW discs formatted in VR mode.
Ver. 2.0/1x – 4x/8x speed
(Video mode)
MTV
CARTOON
● The above table is based on the information as of October 2004.
● Recording and playback may not be performed depending on the
characteristics and condition of the disc used, leading to
unsatisfactory results. Using discs manufactured by JVC is
recommended since they have been tested to be compatible with
this unit.
DVD-RAM Discs
It is only possible to use discs which conform with DVD-RAM
standard Version 2.0 or 2.1.
NOTE:
The following may result if you play back a DVD-R disc recorded
on another unit.
● It is impossible to record on DVD-RAM discs which do not
conform to this standard. If you use a disc formatted under a
different standard version, format it on this unit before use.
● It may not be possible to record, play back, edit or dub a
DVD-RAM disc even if it conforms to the standard if it was
recorded or edited on the devices from other manufacturers or on
a PC, or if it has far too many titles, or if there is very little
available capacity remaining on the disc.
● The disc does not play.
● A mosaic pattern (block noise) appears on the screen.
● Video or audio may be dropped out.
● The unit stops during playback.
● DVD-RAM discs recorded on this unit cannot be played back on
an incompatible DVD player.
● It is possible to record copy-once programs of digital broadcasts
only onto 4.7/9.4 GB DVD-RAM discs (2.8 GB DVD-RAM discs
are not compatible).
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
8
EN
Discs For Playback Only
Unplayable Discs
You can use discs with the following logos for playback only.
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
DVD VIDEO
Video CD/Super Video CD
(example of region code
indications)
● CD-ROM discs (including PHOTO-CD and CD-G)
● Discs recorded in Packet Write (UDF) format
● 1.3-GB double density CDs (DDCD)
● High density CDs (HDCD)
The following discs also cannot be played back.
● Discs of a region number other than A1B
● DVD-RAM (2.6 GB/5.2 GB)
● DVD-RAM (TYPE1)
Audio CD
CD-DA files
CD-R
CD-DA/JPEG/
MP3 files
Caution for DualDisc playback
The Non-DVD side of a ADualDiscB does not comply with the
ACompact Disc Digital AudioB standard. Therefore, the use of Non-
DVD side of a DualDisc on this product may not be recommended.
CD-ROM
JPEG/MP3 files
CD-RW
Region Number
CD-DA/JPEG/
MP3 files
The world is divided into 6 regions for DVD VIDEO discs.
DVD VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played back
on this unit unless the region number of the disc matches that of
the unit. The region number for this unit is A2B. Only discs whose
region number includes A2B or AALLB can be played back such as
shown below.
● Playback may not be performed depending on the characteristics
and condition of the disc used.
● DTS Audio CDs can also be played back (An optional DTS
decoder is required).
● MP3 and JPEG discs can be played back on this unit only when
they have been recorded in the ISO9660 or Joliet format and
finalized.
Examples of DVD VIDEO labels which can be played back
using this unit.
● JPEG files that can be played back on this unit must conform to
JFIF/Baseline process, and the maximum resolution of a JPEG
file is 2,812 pixels in width and 2,112 pixels in height.
● CD-R/RW discs recorded in music CD format need to be finalized
to play back on this unit.
● Operation and audio quality of this unit are not guaranteed for
discs that do not conform to the Compact Disc specification
(CD-DA).
Before you play back a CD, check for the CD logo and read the
notes on the package to confirm that it conforms to the Compact
Disc specification.
● Depending on the intentions of the author of the software,
recording conditions of DVD discs and Video CD/SVCD discs
may be restricted. Since this unit plays back discs according to
the intentions of the author of the software as indicated on the
disc, some functions may not operate as commanded.
● When switching from the first layer to the second layer of double-
layered DVD VIDEO discs, the image and sound may be
momentarily distorted. This is not a malfunction.
● DVD-AUDIO discs compatible with DVD video players can be
played.
Marks of discs in this instruction manual
Allows operation with a
DVD-RAM disc.
Allows operation with a
Video CD/Super Video
CD (SVCD) disc.
Allows operation with a
DVD-R disc.
Allows operation with
an Audio CD disc.
Allows operation with a
DVD-RW disc.
Allows operation with a
disc including MP3
files.
Allows operation with a
DVD VIDEO disc.
Allows operation with a
disc including JPEG
files.
● Super Audio CDs (SACD) compatible with conventional CD
players can be played.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
9
Audio CD/Video CD/SVCD
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video CD/
SVCD discs.
However, some discs are not divided into tracks.
Recording Medium And Format
DVD-RAM
● Recording and erasing can be performed as many times as
possible on a disc.
● Editing can be performed after recording, such as deleting
unwanted parts.
● While recording, it is possible not only to start playback of a
program currently being recorded, but also to watch another
program previously recorded.
Audio CD or Video CD/SVCD
Track 1
Track 2
Track 3
Track 4
DVD-RW (VR mode)
● Recording and erasing can be performed as many times as
possible on a disc.
● Editing can be performed after recording, such as deleting
unwanted parts.
JPEG/MP3 Disc (CD-R/RW/ROM)
MP3/JPEG files put in directories nested in several levels on a disc
will be organized as if they were put in single level directories
(groups) by the MP3/JPEG Navigation of this unit. (A pg. 56)
File structure of a disc before starting the MP3/JPEG
Navigation
DVD-RW (Video mode)
● Can be played back on other DVD players.
● New recording can be performed by erasing all the data on a disc
once played back.
DVD-R
● Can be played back on other DVD players.
● Suitable when keeping a recorded disc for a long time.
File Structure Of Discs
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
AtitlesB. Each title has a number (title number) that can be used to
select desired titles. Titles are further divided into units called
AchaptersB. Each chapter has a number (chapter number) that can
also be used to select desired chapters. Note that some discs are
not divided into titles and chapters.
Directory
MP3 file
JPEG file
File structure of the disc after starting the MP3/JPEG
Navigation
Files are automatically grouped as follows and displayed on the
MP3/JPEG Navigation screen. Data is displayed in the
alphabetical order of file name. Files are grouped based on roots.
When you record a program on a DVD-RAM/RW (VR mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes from monaural to stereo
due to commercial breaks, etc. It is also possible to insert chapter
marks at desired locations during playback. (A pg. 27)
When you record a program on a DVD-R/RW (Video mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes due to commercial breaks,
etc. It is also possible to insert chapter marks at desired locations
during either recording or playback. Once the disc has been
finalized, these chapter marks are deleted and new chapter marks
are assigned automatically approximately every 5 minutes.
DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc
● This unit can recognize up to 9 hierarchies including directories
Title 1
Title 2
and files.
Also, it can recognize up to 250 files in each group, and up to 99
groups on a disc.
Chapter 1 Chapter 2 Chapter 3
Chapter 1 Chapter 2 Chapter 3
NOTES:
● In Video mode, even before finalizing, it is impossible to perform
editing operations other than changing the disc name and/or title
names and deleting programs and/or titles.
● Video CD/SVCD discs that support Playback Control (PBC)
The contents of a disc are recorded into several hierarchies, and
played back according to the instructions on the screen while
navigating through the hierarchies. It is also possible to playback
recorded tracks consecutively without activating the PBC function
even when playing a PBC-compatible disc. (A pg. 28)
● Regarding the contents recorded on discs
Some files may not be played back depending on the file types
and other factors.
● After finalizing, it is impossible to perform editing operations.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
10
DVD VIDEO Marks
Placing A Disc
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of the disc. Check the marks indicating the contents and
functions of the disc. Note, however, that in some cases a disc
may not include a mark even for a function it supports.
Opening the disc tray
Press M to open the disc tray.
Marks related to video
Number of subtitles
Number of angles
EJECT
DV/HDD/DVD
STOP
REC MODE
INSTANT REPLAY
AUDIO DUB.
REC
INSERT
DVD
REC
REW
PLAY
FF
PAUSE
DV IN/ OUT
Recorded under the
standard 4:3 aspect
ratio
Screen includes black
bands at the top and
the bottom of image
which has a standard
4:3 aspect ratio (letter
box)
● Pressing the button again closes the disc tray.
● Use the button to open and close the disc tray.
● Do not block the disc tray with your hand while it is opening or
closing as this may result in hardware failure.
● Do not place unplayable discs or any object other than a disc on
the disc tray.
Video playback is in Wide video mode (16:9) on
wide televisions, but in letter box on televisions
with standard 4:3 aspect ratio.
● Do not press down strongly on the disc tray or place any heavy
objects on it.
Video playback is in Wide video mode (16:9) on
wide televisions, but pan and scan is used on
televisions with standard 4:3 aspect ratio (either
the left or right side of the image is cut-out).
Discs without cartridges
Marks related to audio
Number of audio tracks
I
I
E
OP
ST
SE
LO
N/C
PE
I
E
Dolby Digital mark
It has been developed by Dolby Laboratories as
a digital surround system.
Disc tray
Place the disc on the disc tray with the label side facing up. Since
disc size changes depending on the disc to be played back, be
sure to correctly align the disc with the grooves for its size. If the
disc is not in its groove, it may be scratched or otherwise
damaged. To insert an 8 cm disc, place it according to the inner
groove.
DTS (Digital Theater Systems)
You can enjoy DTS audio if you connect an
amplifier with a built-in DTS decoder to the
DIGITAL OUT connector of the unit.
DVD-RAM discs contained in cartridges
Double-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the side
you wish to play back or record facing down. If you insert the disc
with ASide AB facing down, programs are recorded on the side A.
Single-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the label
side facing up.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
11
Care And Handling Of Discs
How to handle discs
When handling a disc, do not
touch the surface of the disc.
Since discs are made of
plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped, the
images and sound will not be
picked up correctly, and such a
disc may cause the unit to malfunction.
Label side
Do not damage the label side, stick paper to or use any adhesives
on its surface.
Recording side
Make sure that discs are not scratched or dirty on the recording
side before use. Scratches and dirt on the recording side of a disc
may hinder proper playback and recording. Also be careful that a
DVD-RAM disc may get scratched or dirty when removed from
cartridge then put back in after use.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt adhering
to a disc, wipe with a soft dry cloth, moving
from the centre outwards.
If a disc is difficult to clean, wipe with a cloth
moistened with water. Never use record
cleaners, petrol, alcohol or any anti-static
agents.
CAUTION:
Sometimes during playback, noise may appear or images may
be garbled. This is sometimes due to the disc. (It may not be up
to industry standards.)
These symptoms are caused by the discs, not by the
malfunction of the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
12
Front View
J
E
C
K
A
B
D
F
G
H
I
L
M
OPERATE
DISPLAY
EJECT
EJECT
DV/HDD/DVD
STOP
REC MODE
INSTANT REPLAY
AUDIO DUB.
REC
INSERT
DV
REC
HDD
REC
DVD
REC
S-VIDEO
VIDEO (MONO)L
-
AUDIO
-
R
REW
PLAY
FF
PAUSE
−
CH
+
DV IN/ OUT
IN F-1
V
S
T U
Z
N
P
Q
R
W X Y
O
A OPERATE Button (A)
N Display Button (DISPLAY) A pg. 27, 35
O S-video Input Connector [S-VIDEO] A pg. 62
P Video/Audio Input Connectors
[VIDEO/AUDIO ((MONO) L/R)] A pg. 62
Q Channel Buttons (CH +/- JK) A pg. 34, 37
R Front Display Panel A pg. 14
S Infrared Beam Receiving Window
T Stop Button (STOP o) A pg. 24, 39
U Reverse Search Button (O) (HDD & DVD deck) A pg. 25,
44
B Eject Button (EJECT M) (DV) A pg. 41
C Mini DV Cassette Loading Slot
D DV Lamp (DV) A pg. 41
DV Recording Lamp (REC)
E HDD Lamp (HDD) A pg. 20, 37
HDD Recording Lamp (REC) A pg. 37
F DVD Lamp (DVD) A pg. 20, 24
DVD Recording Lamp (REC) A pg. 34
G Open/Close Button (EJECT M) (DVD) A pg. 10
H DV/HDD/DVD Select Button (DV/HDD/DVD) A pg. 24, 37, 41
● This button will not function during navigation mode or set up
mode.
I Recording Mode Button (REC MODE) A pg. 34, 37
J Instant Replay Button (INSTANT REPLAY) A pg. 28, 40, 42
K Disc Tray
Rewind Button (REW O) (DV deck) A pg. 41, 42
V Play Button (PLAY I) A pg. 24, 39
W Forward Search Button (N) (HDD & DVD deck) A pg. 25,
44
Fast Forward Button (FF N) (DV deck) A pg. 41, 42
X Pause Button (PAUSE W) A pg. 24, 39
Y Record Button (REC R) A pg. 34, 37
Z DV Input/Output Connector [DV IN/OUT(A*)] A pg. 60
* A (i.Link) refers to the IEEE1394-1995 industry specification and
extensions thereof. The A logo is used for products compliant with the
i.Link standard.
L Audio Dubbing Button (AUDIO DUB.) A pg. 65
M Insert Button (INSERT) A pg. 66
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
13
Rear View
I
A
B
C
D
E
F
G
H
S
VIDEO
S
VIDEO
VHF/UHF
S
VIDEO
VIDEO
Y
SERIAL COM.
IN
VIDEO
VIDEO
DV/HDD/DVD
OUTPUT
HDD/DVD
P
B
R
DIGITAL
L
L
L
PCM/
AUDIO OUT
STREAM
AUDIO
R
AUDIO
R
AUDIO
R
REMOTE IN
P
OUT
VIDEO
OUTPUT
HDD/DVD
INPUT L-1 OUTPUT
DV/HDD/DVD
COMPONENT
VIDEO OUT
COAXIAL OPTICAL
J
K
L
M
A Region Number A pg. 8
B AC Power Cord A pg. 18
C Cooling Fan
● This prevents the temperature from rising inside the unit.
Do not remove it.
F S-video/Video/Audio Output Connectors [S-VIDEO/VIDEO/
AUDIO OUTPUT] (HDD & DVD deck only) A pg. 18
G S-video/Video/Audio Input Connectors [S-VIDEO/VIDEO/
AUDIO INPUT (L-1)] A pg. 62
H S-video/Video/Audio Output Connectors [S-VIDEO/VIDEO/
AUDIO OUTPUT] A pg. 18
● Install the unit so as not to block the area around the fan.
● The unit may become hot when it is turned off, as the cooling
fan on the rear of the unit is not activated. However, the cooling
fan may be activated in the following cases;
^ When AAUTO CLOCKB is set to AONB (A pg. 21).
(Set AAUTO CLOCKB to AOFFB if you mind the noise of the
fan.)
D Component Video Output Connectors [COMPONENT
VIDEO OUT (Y/PB/PR)] (HDD & DVD deck only) A pg. 18
E Serial Command Connector (D-SUB 9-PIN) [SERIAL COM.]
A pg. 84
I Antenna Input Connector [VHF/UHF IN] A pg. 18
J Digital Audio Output Connectors
[DIGITAL AUDIO OUT (OPTICAL/COAXIAL)] (HDD & DVD
deck only) A pg. 64, 69
K BNC Video Output Connector [VIDEO OUTPUT] A pg. 18
L Remote Input Connector* [REMOTE IN]
* There is currently no compatible remote control unit available.
M Antenna Output Connector [VHF/UHF OUT] A pg. 18
● Use this connector when controlling this unit via a computer.
The cable to be used should be a RS-232C interface cable
(straight type). For details on the RS-232C interface command,
refer to page 86.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
14
Front Display Panel
A
B
C
D
E
F
G
H
I
J
LPCM
FR
XP SP LP EP
RW VCD
RAM
VR
-
-
K
L
M
N
O
P
Q
A Disc Type Indicator
G Track/Chapter Indicator (TRK/CHAP)
When a disc is loaded, the type of the disc is indicated.
Disc Status Indicator
When a disc is running, the disc marks rotate.
During High-Speed Search:
Rotate faster than normal playback.
During Slow Motion:
Rotate slower than normal playback.
While recording:
Inner red ring lights in the same way as normal playback.
During Instant Timer Recording (ITR), inner red ring slowly
blinks.
While paused:
Disc marks blink when either recording or playing back.
ATRKB or ACHAPB lights depending on a disc loaded while the
3rd and 4th digits from the left of the Multi Display (N) indicate
the numbers explained below.
ATRKB: Total number of tracks or track number being played
back are displayed on the Multi Display.
ACHAPB: Chapter number being played back are displayed on
the Multi Display.
H Simulated Surround Effect Indicator (3D) A pg. 31
Lights when a simulated surround effect is set to A3D-ONB on
the on-screen bar.
I Random/Program Playback Mode Indicator (RND/PRGM)
A pg. 32
ARNDB: Lights when Random Playback mode is set.
APRGMB: Lights when Program Playback mode is set.
J Repeat Mode Indicator (x/1/A-B) A pg. 29
Select Repeat Playback mode on the on-screen bar.
While stopped:
While resume stopped:
While the disc tray opened: Disc marks all light out.
No disc on the disc tray: Disc marks all light out.
VR Mode Indicator (VR) A pg. 74
Disc marks all light.
Disc marks all blink.
AxB:
Ax1B:
Whole disc is played back repeatedly.
A single title/chapter/track is played back
repeatedly.
Lights when a DVD-RW disc is formatted in VR mode.
B Linear PCM Indicator (LPCM)
Lights when AXP MODE REC AUDIOB is set to ALINEAR PCMB
(A pg. 71) for recording with HDD, DVD-RAM, DVD-R and
DVD-RW discs, and when Linear PCM audio is played.
C Cassette Loaded Mark (u)
AxA-BB: The selected part (A-B) is played back repeatedly.
No display: Repeat Playback mode is off.
K Video Output Indicator (q) A pg. 76
No display: Indicates that interlace mode is engaged.
q:
Indicates that progressive mode is engaged.
Indicates the present of a cassette in the DV deck.
Lights when a cassette is loaded into the DV deck. It will remain
lit as long as the cassette is loaded, even if the HDD or DVD
deck is being selected.
(Example) q lights when video output mode is in progressive
mode.
L Group/Title Number Display
M Audio Dubbing/Insert Editing Indicator
AADUBB or AINSB lights up during Audio Dubbing or Insert
Editing respectively.
D Recording Mode Indicator (XP/SP/LP/EP/FR) A pg. 34
Blinks when recording mode is being set.
While AFRB is blinking, the left 3 digits of the Multi Display (L
N) indicate setting values ranging from A60B to A480B. After the
value has been set, only AFRB lights.
N Track/Chapter Number Display
O Remaining Time/Elapsed Time Indicator A pg. 27, 35
Lights when remaining time of HDD, DVD-RAM, DVD-R and
DVD-RW discs is displayed, and lights out when elapsed time
is displayed.
E Group/Title Indicator (GRP/TITLE)
AGRPB or ATITLEB lights depending on a disc loaded while the
left 2 digits of the Multi Display (L) indicate the numbers
explained below.
The right 6 digits of the Multi Display (P) indicate elapsed or
remaining time of each track.
AGRPB: Total number of groups or group number being played
back are displayed on the Multi Display.
ATITLEB: Total number of titles or title number being played
back are displayed on the Multi Display.
No display: Indicates elapsed time of the disc.
Displayed: Indicates remaining time of the disc.
P Remaining Time/Elapsed Time Display A pg. 27, 35
Time Code Display A pg. 42
F Channel Indicator
Q Multi Display
Indicates the channel received.
Displays clock, received channel, elapsed time, and remaining
time.
Also displays status of the unit (NO DISC/OPEN/CLOSE/
READING).
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
15
Q Display Button (DISPLAY) A pg. 27, 35, 42
R Audio Button (AUDIO) A pg. 28
Remote Control
S Subtitle Button (SUBTITLE) A pg. 28
T TV/CABLE/DBS/DVD switch A pg. 20
U DVD STANDBY/ON Button (DVD A)
CABLE/DBS
TV DVD
T
U
V TV/CBL/DBS STANDBY/ON Button (TV/CBL/DBS A)
A
STANDBY/ON
DVD
TV/
A pg. 67
W DVD Button* A pg. 24
* This button will not function during navigation mode or set up mode.
X TV Volume Buttons (TV VOL +/–) A pg. 67
Y Channel Buttons (CH +/-) A pg. 34, 67
Z Memo Button (MEMO) A pg. 51, 54
Mark Button (MARK) A pg. 27
a Programming Button (PROG) A pg. 46, 48, 49
b Edit Button (EDIT) A pg. 51
c Navigation Button (NAVIGATION) A pg. 50
d Enter Button (ENTER) A pg. 20
e Return Button (RETURN) A pg. 28, 30, 46
f Forward Skip Button (T) A pg. 25, 44
Next Button (NEXT) A pg. 28
g Forward Search Button (N) (HDD & DVD deck) A pg. 25,
44
TV/CBL/DBS
VIDEO
V
W
B
C
DV
HDD
DVD
TV VOL
X
D
CH
Y
Z
CANCEL
LIVE
AUX
MEMO/MARK
EDIT
E
F
G
H
I
J
DUBBING
PROG
a
b
TV MUTING
Fast Forward Button (N) (DV deck) A pg. 41
Forward Slow Button (SLOW +) A pg. 26
h Play Button (I) A pg. 24, 39
TOP MENU
MENU
NAVIGATION
RETURN
c
Select Button (SELECT) A pg. 56
ENTER
i Pause Button (W) A pg. 24, 39
d
e
f
j Stop Button (o) A pg. 24, 39
K
Clear Button (CLEAR) A pg. 32
k Skip Search Button (v) A pg. 26, 44
l Set Up Button (SET UP) A pg. 20
PREVIOUS
SLOW
NEXT
SLOW
L
M
N
O
m Instant Replay Button (w) A pg. 44
n On-Screen Button (ON SCREEN) A pg. 16, 29
o Progressive Scan Button (PROGRESSIVE SCAN) A pg. 76
p Angle Button (ANGLE) (DVD deck only) A pg. 27
Live Check Button (LIVE CHECK) A pg. 44
PLAY/SELECT
g
h
i
j
k
l
m
CLEAR
STOP/
REC
PAUSE
JUMP
How To Use
REC MODE
REMAIN
DISPLAY
ON SCREEN
SET UP
Before use, insert two AA size batteries into the remote control
with the polarity (F and G) matched correctly as indicated on
the battery compartment or on the lid.
P
Q
n
The remote control can operate most of your unit’s functions, as
well as basic functions of TV sets of JVC and other brands.
(A pg. 67)
● Point the remote control toward the receiving window.
● The maximum operating distance of the remote control is
about 8 m.
PROGRESSIVE
SCAN
AUDIO
SUBTITLE
ANGLE
o
p
R
S
LIVE CHECK
NOTE:
If the remote control doesn’t work properly, remove its batteries,
wait a short time, replace the batteries and then try again.
A TV/VIDEO Button*
* Not function with this unit.
B DV Button* A pg. 41
* This button will not function during navigation mode or set up mode.
C HDD Button* A pg. 37
* This button will not function during navigation mode or set up mode.
D Number Keys A pg. 34, 37
E Cancel Button (CANCEL(L)) A pg. 32
F Auxiliary Button (AUX): Not use on this unit.
G Live Button (LIVE) A pg. 44
H Dubbing Button (DUBBING) A pg. 57
TV Muting Button (TV MUTING) A pg. 67
I Top Menu Button (TOP MENU) A pg. 25
J FGD E Buttons A pg. 20
K Menu Button (MENU) A pg. 25
L Reverse Skip Button (S) A pg. 25, 44, 40
Previous Button (PREVIOUS) A pg. 28
M Reverse Search Button (O) (HDD & DVD deck) A pg. 25,
44
Rewind Button (O) (DV deck) A pg. 41
Reverse Slow Button (SLOW –) A pg. 26
N Record Button (R) A pg. 34, 37
O Jump Button (JUMP +/–) A pg. 40
P Recording Mode Button (REC MODE) A pg. 34, 37
Remain Button (REMAIN) A pg. 27, 35
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
16
When pressing REC MODE
On-Screen Display (HDD & DVD deck)
When ASUPERIMPOSEB is set to AONB or AAUTOB and
ON SCREEN on the remote control is pressed, various operational
indicators appear on the TV screen. To clear the operational
indicators, press ON SCREEN twice.
(Appears for eight seconds.)
7: 00
10: 00
20: 00
28: 00
36: 00
XP
SP
LP
EP
FR480
When playing back a recorded title
HDD
A Remaining disc time for each recording speed
B Recording speed
0:00
1:00
2:00 01:16:48
FR360
Digital
When pressing R during recording
FISHING WORLD
ITR
2 : 30
A Title start
B Current playback point
C Title end
D Elapsed playing time
E Play mode
F Name of title currently being played back
G Time scale (This title is an hour and a half long.)
H Audio mode
A Recording time for Instant Timer Recording (ITR) mode
When using Live Memory playback
HDD
11:00
12:00
13:00
11:35AM
11:33AM
PR.12
FR360
DVD
TITLE99 CHAPTER999 T. REMAIN6:59:59
Digital
DVD
XP
FISHING WORLD
TITLE99 CHAPTER999 T. REMAIN6:59:59
11:35AM
11:33AM
RAM
PR.12
A Playback title number
B Playback chapter number
C Disc remaining time
D Current status (playback)
E Audio mode
FR360
A Time scale for recording (HDD deck)
Bar meter for recording (DVD deck)
B Current recording point
C Recording mode
F Bar meter
G Name of title (or play list) currently being played back
H Current playback point
I Recorded mode
D Current time
E Current playback channel position number
F Time scale for Live Memory Playback (HDD deck)
Bar meter for Live Memory Playback (DVD deck)
G Current playback point
When recording
HDD
H Live Memory playback mode
I Current playback time
11:00
12:00
13:00
11:35AM
PR.12
FR360
LIVE
DVD
TITLE99 CHAPTER999 T. REMAIN6:59:59
11:35AM
RAM
PR.12
FR360
LIVE
A Recording point
B Current status (recording)
C Current time
D Recording channel number
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
17
On-Screen Display (DV Dubbing)
On-Screen Display (DV deck)
When capturing images from the external DV
When ASUPERIMPOSEB is set to AONB or AAUTOB and
equipment
ON SCREEN on the remote control is pressed, various operational
indicators appear on the TV screen. To clear the operational
indicators, press ON SCREEN again.
0:00
FR360 00:00:00. 00
12bit
1:00
2:00
DV
HDD
GR-DV3500
H
00:00:00. 00
DV
JVC
GR-DV3500
SOUND1
W
S P
R
A
B
-
L
1
u
G
F
1 6 B
I
T
A Recording speed
U S E C L E A N I N G C A S S E T T E
B HDD capacity graph
C HDD time counter
D Recording time scale
E HDD mode
C
F Remote control mode
G Connected DV equipment mode
W X
L
R
0
:
0 0
:
0 0
:
0 0
D
E
H Connected DV equipment model information
I Input channel
J Sound mode
K Sound input bit-rate*
* Indicates the sound bit-rate of the connected DV equipment
L Connected DV equipment information*
* Maker name and model name, etc. may not appear depending on the
connected equipment.
M Time counter for the connected DV equipment
N Sound monitor mode
A Operation Mode Indicators
B Tape Speed (SP/LP)
C Sound Mode Display A pg. 71
D Current Month/Day/Year/Clock Display/Time Code Display
A pg. 42
E Audio Mode Display A pg. 42
F Warning Message
G Auxiliary Input Indicator (L-1, F-1 or DV)
H ACassette LoadedB Mark
1
2
DV
DV
O Remote control switch
P Auto capture button
Q Sound monitor switch
179 :59 :59
R Elapsed recording time
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING YOUR NEW UNIT
EN
18
8 S-Video Connection
To connect to TV’s S-VIDEO input and AUDIO input
connectors ^
A Perform A – C of AAV ConnectionB in the left column.
B Connect the unit’s [S-VIDEO OUTPUT] connector to the TV’s
S-VIDEO input connector.
Basic Connections
Antenna or Cable
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
Coaxial cable
● If your TV is not stereo-capable, use the unit’s [AUDIO
OUTPUT] connectors to connect to an audio amplifier for Hi-Fi
stereo sound reproduction.
AC outlet
Flat feeder
To [VHF/
UHF IN]
8 Component Video Connection
Matching transformer
(not supplied)
To connect to TV’s component video input connectors ^
A Perform A – C of AAV ConnectionB in the left column.
B Connect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)]
connectors to the TV’s component video input connectors.
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
AC power cord
● You can obtain high-quality component video pictures.
● The [COMPONENT VIDEO OUT (Y/PB/PR)] connectors do not
output DV signals.
● If your TV is not stereo-capable, use the unit’s [AUDIO
OUTPUT] connectors to connect to an audio amplifier for Hi-Fi
stereo sound reproduction.
Back of unit
To
[COMPONENT
To
To
To
To
[VIDEO
OUTPUT]
[AUDIO/
[S-VIDEO
[VHF/
UHF
OUT]
VIDEO
OUTPUT]
VIDEO OUT (Y/
OUT]
PB/PR)]
● By using the component video connection, you can view the
images in the progressive mode. For switching to the
progressive mode, refer to AScan Mode Set (HDD & DVD Deck
Only)B (A pg. 76).
Component
video cable
(not supplied)
Audio/Video
S-video cable
BNC video
cable (not
supplied)
RF cable
(supplied)
cable
(not supplied)
(supplied)
4 Plug the end of the AC power cord into an AC outlet.
This unit performs Plug & Play Set automatically. (A pg. 19)
● The clock and tuner channels will automatically be set when the
antenna is connected and when the AC power cord is first
connected to an AC outlet. (If AAUTOB and the channel indicator
are displayed on the front display panel before the unit is
powered on, the clock and tuner channels are being set
automatically. Wait for the time to be displayed on the front
display panel before turning on the unit.)
TV
● ALOADINGB blinks on the front display panel when the AC plug
of the AC power cord is connected into a AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is
not a malfunction.
It’s essential that your unit be properly connected.
ATTENTION:
Connect the AC plug only after all connections to the TV has
been completed.
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
1 Make sure the package contains all of the accessories listed in
ASPECIFICATIONSB (A pg. 88).
2 Place the unit on a stable, horizontal surface.
3 Connect the unit to a TV depending on the TV and cables you
use.
8 AV Connection
To connect to a TV with AV input connectors ^
A Disconnect the TV aerial cable from the TV.
B Connect the TV antenna cable to the [VHF/UHF IN] connector
on the rear panel of the unit.
C Connect the [VHF/UHF OUT] connector on the rear panel of the
unit and the TV’s antenna connector with the supplied RF
cable.
D Connect the supplied audio/video cable between the [AUDIO/
VIDEO OUTPUT] connectors on the rear panel of the unit and
the TV’s audio/video input connectors.
● if your TV is equipped with a BNC video connector, connect an
optional BNC video cable between the unit’s BNC [VIDEO
OUTPUT] connector and the TV’s BNC VIDEO input connector.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
19
1 Connect the antenna cable to the unit. (A pg. 18) Then connect
the AC power cord to an AC outlet. Do not turn on the unit.
The clock and tuner channels will be set automatically.
● ALOADINGB blinks on the front display panel when the AC plug
of the AC power cord is connected into an AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is
not a malfunction.
Plug & Play Set
Auto Clock Set/Auto Tuner Set
This unit sets the clock and tuner channels automatically when AC
power cord is first connected to an AC outlet. The antenna cable
must be connected for the Plug & Play setting.
The time and date can be set automatically by the clock setting
data transmitted from one of the regular TV broadcast channels.
We call this TV channel the “host channel” and it is a PBS channel
in your area.
NOTES:
● Auto Clock Set is performed first.
AAUTOB blinks on the front display panel during Auto Clock Set.
● Auto Channel Set is performed next. Auto Channel Set scans all
the channels that are receivable by your unit. During Auto
Channel Set, the channel numbers are displayed as they are
scanned and set.
● When Plug & Play setting has been completed successfully, the
correct clock time is displayed. If you perform Plug & Play setting
successfully, there is no need to perform AClock SetB (A pg. 21)
and ATuner SetB (A pg. 22). If, however, you want to add or
delete channels, refer to AManual Channel SetB (A pg. 22).
ATTENTION:
● If you use a cable box, Plug & Play will not function; set the
clock and tuner channels separately. (੬ pg. 21 – 22)
● Depending on areas or reception conditions, the unit may not
receive the Auto clock setting data from the PBS channel. If
this function is taking a considerable amount of time, it may be
necessary to perform the Semiauto or Manual Clock Set
procedure.
During Auto Clock Set
AAUTOB blinks.
During Auto Channel Set
The channel numbers are displayed and AAUTOB blinks as they
are scanned and set.
INFORMATION
● If AAUTO CLOCKB is set to AONB (A pg. 21), the clock will be
adjusted automatically by the host channel every hour (except
11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming
PBS channel clock setting data. (This automatic clock
adjustment can only be performed when the unit is turned off.
The clock will be adjusted just on these hours — on the time
displayed on the front display panel, not on the actual real
time.) The default setting of AAUTO CLOCKB is AONB.
(A pg. 21)
Plug & Play Completed
The current time is displayed.
● If an incorrect clock time or AcB appears on the front display
panel, see AWhat to do if Plug & Play setting failedB (A pg. 19).
● If the memory backup fails, because a power outage occurs or
because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the unit.
What to do if Plug & Play setting failed
● If an incorrect time is displayed on the front display panel, you
may be receiving the clock setting data of a PBS channel from
an adjacent time zone, or an incorrect PBS channel from a
cable TV system. In this case, perform ASemiauto Clock SetB
(A pg. 21) or AManual Clock SetB (A pg. 21).
● If AcB appears on the front display panel, your antenna
cable may not be connected to the unit or there may not be a
Host PBS signal available in your area. Ensure that the
antenna cable is connected correctly. Then turn on and off the
unit; the Plug & Play setting will be automatically reactivated. If
Plug & Play setting is not performed though the antenna cable
is connected correctly, perform AManual Clock SetB (A pg. 21)
and AAuto Channel SetB (A pg. 22) or AManual Channel SetB
(A pg. 22).
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
20
On-screen Language Set
This unit offers you the choice to view on-screen messages in 3
different languages.
Language
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press D E to select AFUNCTION SET UPB, then press G.
4 Press D E to select ADISPLAY
CABLE/DBS
TV
DVD
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
INITIAL SET UP
SETB, then press G.
REC/PLAY SET UP
DISPLAY SET
VIDEO IN/OUT
HDD
DVD
SUPERIMPOSE
BLUE BACK
DIMMER
AUTO
5 Press F G to select AON
SCREEN LANGUAGEB, then
press ENTER.
ON
BRIGHT
OFF
POWER SAVE
ENGLISH
ON SCREEN LANGUAGE
6 Press F G to select your desired
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
ENTER
SET UP
EXIT
language, then press ENTER.
SELECT
7 Press SET UP to complete the
setting.
ENTER
FGDE
Menu/Audio/Subtitle Language Set (DVD deck only)
Some DVD discs contain the DVD menu display, audio and
subtitles in multiple languages. With these discs, you can set the
default language as you like.
● The procedure shows how to set AMENU LANGUAGEB as an
example.
SET UP
1 Press DVD so that the DVD lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
3 Press D E to select ADVD VIDEO SET UPB, then press G.
4 Press D E to select
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
INITIAL SET UP
ALANGUAGE SETB, then press
G.
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LOCK DISC PLAY SET UP
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ENGLISH
ENGLISH
ENGLISH
5 Press F G to select AMENU
LANGUAGEB, then press
ENTER.
ENTER
SET UP
EXIT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
6 Press F G to select your desired
SELECT
language, then press ENTER.
● See ALanguage Code ListB (A pg. 81).
7 Press SET UP to complete the setting.
NOTE:
When the selected language is not available on the disc, the disc’s
default menu language is played back.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
21
8 Press F G to select ATIME ZONEB, then press ENTER. Press
F G to select AAUTOB or the desired time zone, then press
ENTER.
● Each time you press F G, the time zone changes as follows:
YAUTOYATLANTICYEASTERNYCENTRALYMOUNTAINY
PACIFICYALASKAYHAWAIIY(back to the beginning)
Clock Set
Perform clock setting only if the clock has not been set correctly by
the Plug & Play setting.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
NOTE:
If an incorrect time is displayed by the Plug & Play function, you
may be receiving the clock setting data of a PBS channel from an
adjacent time zone or from an incorrect PBS channel from a cable
TV system. If you selected AAUTOB for the host channel in step 6,
be sure to select the correct time zone manually.
CABLE/DBS
TV
DVD
9 Press SET UP to complete the setting.
HDD
DVD
IMPORTANT
Turn off the unit after performing Semiauto Clock. AAUTOB will
appear on the front display panel while the clock is being set.
The current clock time will appear automatically when the clock
setting is complete.
ENTER
Auto Daylight Saving Time
FGDE
This function enables automatic adjustment of the unit’s clock at
the start and end of Daylight Saving Time.
With Auto DST activated, ^
^ on the first Sunday of April at 2:00 AM, the clock is adjusted
to 3:00 AM.
^ on the last Sunday of October at 2:00 AM, the clock is
adjusted to 1:00 AM.
SET UP
NOTE:
Timer recording may not function correctly at the time Daylight
Saving Time is adjusted.
Manual Clock Set
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
Semiauto Clock Set
the unit.
You can change the host channel/D.S.T. (Daylight Saving Time)/
time zone setting manually.
2 Press SET UP to access the Main Menu screen.
3 Press D E to select AINITIAL SET UPB, then press G.
4 Press D E to select ACLOCK
NOTE:
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
INITIAL SET UP
The time set previously will be erased when AAUTO CLOCKB,
AHOST CHB, AD. S. T.B or ATIME ZONEB setting is changed.
SETB, then press G.
TUNER SET
CLOCK SET
AUTO CLOCK
HOST CH [CATV]
D. S. T.
ON
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
AUTO
AUTO
AUTO
the unit.
TIME ZONE
2 Press SET UP to access the Main Menu screen.
3 Press D E to select AINITIAL SET UPB, then press G.
4 Press D E to select ACLOCK
SET UP
EXIT
ENTER
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
SELECT
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
INITIAL SET UP
5 Press F G to select AAUTO
CLOCKB, then press ENTER.
Press F G to select AOFFB,
then press ENTER.
SETB, then press G.
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
INITIAL SET UP
TUNER SET
CLOCK SET
TUNER SET
CLOCK SET
AUTO CLOCK
HOST CH [CATV]
D. S. T.
ON
5 Press F G to select AAUTO
CLOCKB, then press ENTER.
Press F G to select AONB, then
press ENTER.
OFF
AUTO CLOCK
TIME
AUTO
AUTO
AUTO
– –:– –
1/1(SAT)
DATE
TIME ZONE
6 Press F G to select ATIMEB,
then press ENTER. Press F G
until the desired time appears,
then press ENTER to start
clock.
YEAR
2005
ON
D. S. T.
SET UP
EXIT
ENTER
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
6 Press F G to select AHOST CH
[CATV]B, then press ENTER.
Press F G to select AAUTOB or
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
SET UP
EXIT
ENTER
SELECT
SELECT
the desired PBS channel number, then press ENTER.
● Set the date and year in the same way.
NOTE:
● Holding F G changes the time in 30-minutes interval, or
changes the date in 15-days interval.
Some PBS channels do not transmit clock setting data.
7 Press F G to select AD. S. T.B, then press ENTER. Press F G
7 Press F G to select AD. S. T.B, then press ENTER. Press F G
to select the desired setting, then press ENTER.
to select the desired setting, then press ENTER.
AUTO:
ON:
Select if you want to adjust your unit’s clock automatically by
the incoming signal from the host channel. Be sure to select the
correct time zone manually in step 8.
Adjustment will be made by the built-in clock itself.
OFF:
Select when Daylight Saving Time does not apply to you.
ON:
8 Press SET UP to complete the setting.
Adjustment will be made by the built-in clock itself.
OFF:
Select when Daylight Saving Time does not apply to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
22
Manual Channel Set
You can add the channels you want or delete the channels you do
not want manually.
Tuner Set
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press D E to select AINITIAL SET UPB, then press ENTER.
4 Press D E to select ATUNER SETB, then press G.
CABLE/DBS
TV
DVD
5 Press FGD E to select AMANUAL CH SETB, then press
HDD
0-9
DVD
ENTER.
6 Add or skip the desired
INITIAL SET UP > MANUAL CH SET
channels.
BAND
CH
CATV
1
To add channels
A Press F G to select ACHB, then
press ENTER.
B Press the number keys to enter
a channel number you want to
add, then press ENTER.
ADD/SKIP
ADD
RETURN
ENTER
SET UP
EXIT
ENTER
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
FGDE
SELECT
0-9
C Press F G to select AADD/SKIPB, then press ENTER.
D Press F G to select AADDB, then press ENTER.
E Repeat B – D to add other channels.
To skip channels
A Press F G to select ACHB, then press ENTER.
B Press F G to select a channel number you want to skip, then
press ENTER.
SET UP
C Press F G to select AADD/SKIPB, then press ENTER.
D Press F G to select ASKIPB, then press ENTER.
E Repeat B – D to skip other channels.
7 Press SET UP to complete the setting.
INFORMATION
The unit selects the correct band (TV or CATV) automatically
during Auto Channel Set. The selected band will be displayed on
the right side of ABANDB on the Tuner Set screen.
Auto Channel Set
Perform Auto Channel Set only if channels have not been set
correctly by the Plug & Play setting.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press D E to select AINITIAL SET UPB, then press G.
4 Press D E to select ATUNER
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
TUNER SET
INITIAL SET UP
SETB, then press G.
CLOCK SET
AUTO CH SET
MANUAL CH SET
GUIDE CH SET
11
2
13
SET UP
EXIT
ENTER
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
SELECT
5 Press FGD E to select AAUTO
CH SETB, then press ENTER.
You can automatically set the
receivable channels in your
area in the order of their
frequencies.
INITIAL SET UP > AUTO CH SET
AUTO CHANNEL SET
SCANNING...
CANCEL
● When Auto Channel Set is
complete, ASCAN
SET UP
EXIT
ENTER
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
SELECT
COMPLETEDB appears on the
TV screen.
● If the scan was unsuccessful, ASCAN COMPLETED –NO
SIGNAL–B appears on screen. Check the connections and start
again.
6 Press SET UP to complete the setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
23
1 Press DVD so that the DVD lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
Monitor Set
● You cannot set the monitor type during recording or playback.
3 Press D E to select AFUNCTION SET UPB, then press G.
4 Press D E to select AVIDEO IN/
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
DVD VIDEO SET UP HDD/DVD SET UP
FUNCTION SET UP
VIDEO IN/OUT
INITIAL SET UP
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
OUTB, then press G.
REC/PLAY SET UP
DISPLAY SET
MONITOR TYPE
FRONT AUX F-1
REAR AUX L-1
4:3LB
5 Press F G to select AMONITOR
VIDEO
VIDEO
TYPEB, then press ENTER.
6 Press F G to select the desired
option, then press ENTER.
CABLE/DBS
TV
DVD
ENTER
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
SET UP
EXIT
7 Press SET UP to complete the
setting.
DVD
* The boldface settings below indicate the settings at your purchase.
8 MONITOR TYPE - 4:3LB / 4:3PS / 16:9AUTO / 16:9FIX
4:3LB (Letter Box conversion):
Select this when the aspect ratio of your TV is 4:3 (conventional
TV). While viewing a wide screen picture, the black bars appear
on the top and the bottom of the screen.
ENTER
FGDE
4:3PS (Pan&Scan):
Select this when the aspect ratio of your TV is 4:3 (conventional
TV). While viewing a wide screen picture, the black bars do not
appear; however, the left and right edges of the pictures will not
be shown on the screen.
16:9AUTO (Wide television conversion):
SET UP
Select this when the aspect ratio of your TV is 16:9 (wide TV).
16:9FIX (Wide television conversion):
Select this when the aspect ratio of your TV is fixed to 16:9
(wide TV). The unit automatically adjusts the screen width of
the output signal correctly when playing back a picture whose
aspect ratio is 4:3.
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen TV
with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect ratio.
There are two styles to display the image, APan&ScanB (PS) and
ALetter BoxB (LB).
Pan&Scan
The right and left side of the image are cut off.
The image fills the screen.
● The picture will be shown in the A4:3LBB mode
depending on the disc even if the A4:3PSB
mode is selected.
Letter Box
Black bands appear at the top and bottom of
the image. The image itself appears in 16:9
aspect ratio.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
24
To play back an MP3/JPEG disc, see APlayback With MP3/WMA/
JPEG NavigationB (A pg. 56).
Basic Playback
1 Load a disc.
● For details, refer to APlacing A DiscB (A pg. 10).
● Pressing I also closes the disc tray.
● Playback begins automatically if an auto-playback DVD disc is
loaded.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
2 Press DV/HDD/DVD on the unit repeatedly or DVD on the
remote so that the DVD lamp lights up on the unit.
3 Press I to start playback.
● If you load a DVD disc whose region code does not match the
unit, AREGION CODE ERRORB appears on the TV screen. For
details, refer to ARegion NumberB (A pg. 8).
DV/HDD/DVD
● If ACAN NOT PLAY BACK DISC UNDER CURRENT SETTINGB
appears on the TV screen, refer to AParental LockB (A pg. 33).
● With Video CD/SVCD discs with PBC control or some DVD
discs, the menu display may appear on the TV screen after
starting playback. In this case, select an item which you want to
play back from the menu. Otherwise, the playback cannot go
forward. Refer to APlayback Control (PBC) FunctionB (A pg. 28)
or ALocating A Desired Scene Using The DVD MenuB
(A pg. 25).
o
I
W
M
CABLE/DBS
TV DVD
● The Library Database Navigation also enables you to search
and select the desired titles. (A pg. 51)
DVD
4 Press W to pause playback.
● To resume normal playback, press I.
5 Press o to stop playback.
● When a recordable disc is played, playback stops and a
program received with the unit’s tuner resumes on the TV
screen.
ENTER
● When a playback-only disc is played, playback stops and the
TV screen becomes all blue when you press o. Pressing o
again resumes a program received with the unit’s tuner.
● If M is pressed during playback, playback stops, then the disc
tray opens.
I
o
W
NOTES:
● When the Library Database Navigation screen appears, choose
a thumbnail image of the desired title on the TV screen, then
press ENTER. (A pg. 51)
● It is not possible to playback the DVD disc recorded in 96 kHz on
DVD during recording or Live Memory Playback on HDD.
ATTENTION:
● It takes approximately 30 seconds to read a disc depending on
the type and condition of the disc since this unit is multi-disc
compatible (DVD-RAM, DVD-RW, DVD-R). It may even take
several minutes when a disc is dirty, scratched or warped.
● It may take a few seconds to start playback. This is not a
malfunction.
● Forward/reverse high-speed search and other operations
cannot be performed while playback is stopped.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
25
Locating The Start Point Of The Item Or Skip The Item
Playback Features
● Turn on the unit.
Press S or T during playback.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD so that the DVD lamp lights up on the unit.
● Pressing T locates the start point or marked points of the item
or skips the item in the forward direction, then resumes playback.
● Pressing S locates the start point or marked points of the item
or skips the item in the reverse direction, then resumes playback.
CABLE/DBS
TV
DVD
Current playback point
DVD
0-9
Previous
program
or
Scene 2
(Chapter 2)
or
Drama
or
Scene 3
(Chapter 3)
or
Movie
or
Scene 5
(Chapter 5)
or
Next program
or
Scene 4
(Chapter 4)
or
TOP MENU
ENTER
FGDE
T
MENU
S
I
Track 3
Track 5
Track 4
Track 2
N/SLOW +
W
O/SLOW
-
Forward
Reverse
o
● : marked points (A pg. 27)
JUMP
-
JUMP +
Variable Speed Search
During playback, press N for forward variable speed search, or
O for reverse variable speed search.
● Each press of the button increases the search speed for each
direction.
Locating A Desired Scene Using The DVD Menu
● To resume normal playback, press I.
For Audio CD
DVD VIDEO discs may have top menu and disc menu.
You can perform 4 levels of speed search with N and O. (Audio
is active also during variable speed search.) You cannot perform
slow motion for each direction.
Top menu
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Reverse
O
N
Forward
Reverse
Slow Motion
3 steps
Reverse Search Reverse
Normal
Play
Slow Motion
3 steps
Forward Search
4 steps
Disc menu
4 steps
Play
Disc menus include playback data (angle menu, subtitle menu,
etc.) specific to each title.
1
-
116
-
½
-
¼
60
-60 -15 -5 -3
-1
1
3
5
15
½
¼
16
Press MENU to access the disc menu.
1 Press TOP MENU or MENU to
Still Picture/Frame-By-Frame Playback
access the DVD menu.
2 Press FGD E to select a
desired title, then press
ENTER. Playback starts.
● It may be possible to select the
desired item using the number
keys depending on the menu
1 Press W to pause during playback.
2 Press SLOW – (O) or SLOW + (N) to activate frame-by-
frame playback.
● Each press of SLOW – (O) or SLOW + (N) advances/
reverses the still picture frame by frame.
● Frame-by-frame playback for reverse direction cannot be
performed with Video CD/SVCD discs.
display.
Example:
NOTE:
When A7B appears on the TV screen in step 1, the disc does not
have a top menu or disc menu.
● To resume normal playback, press I.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
26
Slow Motion
Resume Function
It is possible to memorize the position where you stop playback
and resume playback from that position.
● Be sure to set ARESUMEB to AONB or ADISC RESUMEB.
(A pg. 71)
● Resume function always works for DVD-R/DVD-RW discs that
have not been finalized and DVD-RAM regardless of the setting
of ARESUMEB.
1 Press W to pause during playback.
2 Press SLOW – (O) or SLOW + (N) for 2 or more seconds.
● Each press of SLOW – (O) or SLOW + (N) increases the
slow motion speed for each direction.
● Slow motion for reverse direction cannot be performed with
Video CD/SVCD discs.
1 Press o during playback to memorize a resume point.
● The unit enters Resume Stop mode and memorizes the
position where you have stopped playback as a resume point.
(The inside of the disc status indicator on the front display panel
blinks while memorizing.)
● The unit retains a memory of the resume points of the last 30
discs played back, even though they have been ejected if
ARESUMEB is set to ADISC RESUMEB. (A pg. 71)
● To clear the resume points:
Skip Search
During playback, press v.
● Each press initiates an approximately 30-second period of fast-
motion playback. Normal playback resumes automatically.
● Skip search cannot be performed when a VCD/SVCD disc is
being played back with the PBC function.
(The inside of the disc status indicator stops blinking and
lights.)
Jump Search
When ARESUMEB is set to AONB:
• Press A to turn off the unit.
• Press M to take out the disc.
• Press o in stop mode.
• Press TOP MENU to display the top menu, then start playback
by selecting an item, etc.
• Press MENU to display the disc menu, then start playback by
selecting an item, etc.
When ARESUMEB is set to ADISC RESUMEB:
• Set ARESUMEB to AOFFB. (A pg. 71)
• Press o in stop mode.
• Press TOP MENU to display the top menu, then start playback
by selecting an item, etc.
• Press MENU to display the disc menu, then start playback by
selecting an item, etc.
You can locate a scene ahead or behind the current one by
jumping scenes according to selected time intervals (A pg. 72)
during playback (or Live Memory Playback).
Press JUMP – or JUMP +.
● To advance forward or back, press JUMP – or JUMP +
repeatedly within 5 seconds of each press to continue jump.
● Depending on the time from where you want to start jump search,
the first press of JUMP – or JUMP + will not necessarily lead to a
jump of the selected time interval. The first press will lead to a
jump to the nearest quarter points of an hour (15 min/ 30 min/ 45
min/ 00 min). The subsequent jumps will then be in accordance
to the selected time interval.
2 Press I in stop mode to resume playback. The unit starts
● When you cannot advance any further (beginning or end of
program reached), the message AUNABLE TO GO BACK ANY
MOREB appears on the screen and the on-air screen resumes. In
such a case, press S, O or o.
playback from the resume point.
NOTES:
● ADISC RESUMEB setting works on DVD VIDEO, VCD, SVCD and
already finalized DVD-R/DVD-RW (video mode) discs. For other
types of discs, the function under AONB setting will be applied
even if ARESUMEB is set to ADISC RESUMEB. (A pg. 71)
● If you stop the playback of a disc for which a resume point has
already been memorized, the memory will be updated with the
new resume point.
Example:
Playback search when jump interval is set to 15 MIN jumps.
Taking for instance, you want to start jump search 40 minutes after
the beginning of the program. Pressing JUMP – or JUMP + will
result in a jump to the scene at the 30 minutes point or 45 minutes
point respectively as illustrated below. At the subsequent press, the
scene will jump to the 15 minutes point or 1 hour point respectively,
● After the unit has memorized the resume points for 30 discs,
remembering a new resume point will cause the unit to delete the
oldest memorized point. Stopping playback of a disc for which a
resume point is already stored may change the order in which the
points are stored. This may potentially change the order in which
points are deleted.
● When the unit memorizes a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
● This function may not work for some Video CD/SVCDs.
● When ARESUMEB is changed to AONB or AOFFB (A pg. 71),
resume points of the discs memorized with ARESUMEB set to
ADISC RESUMEB will be cleared.
according to the selected time interval, which in this case is
A15 MINB.
Time counter
40 min
0 min
1 h 15 min
15 min
30 min
45 min
1 h
Beginning of program
Current scene
End of program
NOTE:
Jump search cannot be performed with finalized DVD-R/DVD-RW
(video mode) discs.
● Resume points are memorized for each side of a double-sided
disc.
● When you switch to HDD while playing back JPEG/MP3 files,
playback stops. The Resume Function doesn’t work when you
switch to DVD thereafter to playback the disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
27
Checking The Time Information
CABLE/DBS
TV DVD
DVD
You can check time information of a disc on the front display panel
and the TV screen.
0-9
8 DVD-RAM/DVD-R/DVD-RW
Each press of DISPLAY on the remote control or the unit changes
the display as follows:
During recording
MARK
Clock time (front display panel only) N Current title elapsed time
N Disc remaining time* N (back to the beginning)
* only discs before finalizing
ENTER
FGDE
MENU
RETURN
During playback
S/PREVIOUS
T/NEXT
Each title elapsed time N Current title elapsed time N
Disc remaining time* N (back to the beginning)
* only discs before finalizing
I
o
REC MODE/REMAIN
DISPLAY
During recording/playback or in stop mode
Press REC MODE.
SET UP
● The disc remaining time according to recording modes appears
on the TV screen.
● It is possible to check disc remaining time according to recording
modes also by pressing REMAIN.
AUDIO
SUBTITLE
ANGLE
● In FR mode, it is possible to set recording time in detail. While the
recording mode and the disc remaining time are displayed by
pressing REMAIN, press F G to select AFRB, then press D E to
select the desired recording time. (A pg. 36)
● It is not possible to switch the recording mode during playback or
while recording.
Marking Positions To Play Back Again Later
8 Video CD/SVCD/Audio CD
It is possible to mark positions (up to 999 points) where you want
to play back once again later, and start playback from a marked
position. Marking onto DVD-RAM/RW (VR mode only) discs when
recording is helpful to locate a start point when you play back the
discs later.
During playback or in stop mode
Current track elapsed time N Current track remaining time N Total
elapsed time N Total remaining time N (back to the beginning)
NOTE:
When a PBC-compatible Video CD/SVCD disc is loaded,
deactivate the PBC function. (A pg. 28)
To mark positions:
During playback, press MARK at
positions you want to mark.
● AMARKB appears on the TV screen.
You can easily locate the marked
positions using S or T when
you play back the disc.
Angle Selection
You can enjoy a variety of scene angles if a DVD VIDEO disc
contains Amulti-angleB parts, where the same scene was shot from
different angles.
If the disc contains Amulti-angleB parts, AyB appears on the TV
screen at the beginning of the Amulti-angleB part.
To delete the marked positions:
While paused, press S or T to
locate a marked position you want to
delete, then press MARK.
● Crossed AMARKB appears on the
TV screen, and the marked position
is deleted.
1 Press ANGLE during
playback. The angle selection
display appears on the TV
screen.
When 3 scene angles are
contained.
NOTES:
● When a monaural program changes to a stereo program while
recording, a mark signal is automatically recorded.
● For DVD-R/RW (Video mode) discs, marks are assigned
automatically every 5 minutes.
2 Press ANGLE or D E to select
your desired angle.
● Each time you press ANGLE or D E, the angle changes.
● When A7B appears on the TV screen, the current scene is not
recorded from multiple angles. In addition, some discs prohibit
angle selection.
● If MARK is pressed when playing back a disc that does not allow
marks to be inserted, A7B appears on the TV screen.
● To clear the angle selection display, press ENTER. In addition,
the angle selection display disappears automatically if no
operation is done for 10 seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
28
Subtitle Selection
Audio Language/Sound Selection
Some DVD VIDEO discs contain more than one subtitle language,
from among which you can choose the desired subtitle language.
AhB appears on the TV screen at the beginning of the part where
more than one subtitle language are recorded.
Some DVD VIDEO discs contain the multiple audio language or
sound. You can select the desired audio language or sound. For
some Video CD/SVCD discs, you can switch the audio channel to
choose Karaoke either with or without the vocal.
1 Press SUBTITLE during
1 Press AUDIO during playback.
For example: DVD VIDEO
ENGLISH
playback. The subtitle
The Audio Language/Sound
selection display appears.
selection display appears on
the TV screen.
● Each time you press
SUBTITLE, the subtitle display
is switched on and off.
When 3 subtitle languages are
contained.
2 Press AUDIO or D E to select
When 3 audio languages are
contained.
your desired audio language/
sound.
● Each time you press AUDIO or D E, the audio language/sound
changes.
● To clear the Audio Language/Sound selection display, press
ENTER.
2 Press D E to select your desired language.
● To clear the subtitle selection display, press ENTER.
NOTES:
● When A7B appears on the TV screen, no subtitle language is
NOTES:
recorded.
● When A7B appears on the TV screen, no audio language is
recorded.
● When the subtitle language won’t be changed with the procedure
above, change the subtitle on a disc menu displayed by pressing
MENU.
● When the audio language won’t be changed with the procedure
above, change the audio on a disc menu displayed by pressing
MENU.
● Pressing AUDIO to select the audio language/sound is only
possible during playback. It is not possible to select by pressing
AUDIO in stop mode. However, you can select the desired audio
language/sound from the setup menu while in stop mode.
Audio Channel Selection
When watching bilingual programs or playing discs on which you
recorded bilingual or stereo programs, you can choose the desired
audio channel.
Playback Control (PBC) Function
● When ASUPERIMPOSEB is set to AONB or AAUTOB, you can
confirm on the TV screen the audio channel you have chosen.
(A pg. 72)
● Each time you press AUDIO, the audio
channel changes.
Some Video CD/SVCD discs support the PBC function. PBC is an
abbreviation of APlay Back ControlB. A Video CD/SVCD disc
recorded with PBC has its own menus, such as a list of the songs
on the disc. You can locate a specific scene by using the menu.
1 Press I in stop mode. The PBC menu appears.
TRACK
USE
2 Press the number keys to enter the number of the desired
scene, then press ENTER. The unit starts playback of the
selected item.
On-Screen Display
For stereo discs
● APBCB appears on the front display panel.
For audio of left channel
For audio of right channel
● When ANEXTB or APREVIOUSB appears on the TV screen:
Pressing NEXT(T) advances to the next page.
Pressing PREVIOUS(S) returns to the previous page.
● You can return to the menu by pressing RETURN.
● The method of the operation is different depending on the disc.
When you can’t switch the audio channel of a bilingual
program
When the unit is connected with a digital audio device using an
optional optical cable and ADIGITAL AUDIO OUTB is set to
ADOLBY DIGITAL/PCMB, it is not possible to switch the audio
channel of a bilingual program recorded on a DVD-RAM or
DVD-RW (VR mode) disc. (A pg. 69) In this case, perform the
following steps using the remote control to switch ADIGITAL
AUDIO OUTB from ADOLBY DIGITAL/PCMB to APCM ONLYB.
A Press SET UP to access the Main Menu screen.
B Press D E to select ADVD VIDEO SET UPB, then press G.
C Press D E to select AAUDIO OUTPUTB, then press G.
D Press F G to select ADIGITAL AUDIO OUTB, then press
ENTER.
NOTE:
If you want to playback a PBC-compatible Video CD/SVCD disc
without activating the PBC function, start playback with the PBC
function, then press o to stop playback. The TV screen becomes
all blue. Then start playback in stop mode by using the number
keys to choose the track, then press ENTER.
Instant Replay
You can move back the playback position slightly.
Press w on the remote control or INSTANT REPLAY on the unit.
● Each press skips back for approximately 7 seconds and resumes
playback.
E Press F G to select APCM ONLYB, then press ENTER.
(A pg. 70)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
● Pressing while paused skips back for approximately 7 seconds
and resumes pause.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
29
A Disc type.
B Select this for Repeat Playback. (A pg. 29)
C Select this for A-B Repeat Playback. (A pg. 30)
D Select this for search function. (A pg. 30)
E Select this for time search function. (A pg. 31)
Using The On-screen Bar
F Select this to switch Simulated Surround Effect function.
(A pg. 31)
G Select this for Picture Control function. (A pg. 31)
H Select this to switch picture source type. (A pg. 32)
I Current status area for the selected item.
J Select this for Program Playback. (A pg. 32)
K Select this for Random Playback. (A pg. 32)
The on-screen bar allows you to control various playback
functions. Some of the functions operated on Navigation Menu can
be controlled on the On-screen bar.
ATTENTION:
The on-screen bar can also be used for the HDD deck.
L Select this to control the switching interval of the slide show.
(A pg. 32)
Be sure to clear Library Database Navigation screen by pressing
NAVIGATION.
NOTE:
Although examples of the on-screen bar are provided here only for
3 types of discs, the on-screen bar will be displayed for whichever
disc indicated in the left column.
CABLE/DBS
TV
DVD
Basic Operation On The On-screen Bar
Example: When selecting Picture Control function of DVD
During playback or while stopped
1 Press ON SCREEN twice to access the on-screen bar. The
item currently selected is highlighted and pointed by :.
NAVIGATION
FGDE
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
ENTER
DVD-
RETURN
VIDEO
2 Press D E to select A
B, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
ON SCREEN
DVD-
VIDEO
3 Press F G to select the desired option, then press ENTER.
TITLE 99
CHAPTER 99
EACH 0:00
How To Access The On-screen Bar
3D-ON CINEMA AUTO
DVD-
VIDEO
1 Press ON SCREEN twice whenever a disc is loaded.
NORMAL
CINEMA
SHARP
SOFT
Contents of the on-screen bar during playback
DVD VIDEO
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
To clear the on-screen bar
Press ON SCREEN.
DVD-
VIDEO
NOTE:
See the corresponding pages for details on each menu item.
Repeat Playback
Video CD/SVCD
TRACK 99
EACH 0:00
CINEMA
You can repeat playback as you like according to the type of disc.
VCD
1 Press ON SCREEN twice to access the on-screen bar.
2 Press D E to select AxB, then press ENTER. The pop-up
window appears under the selected item.
JPEG disc
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
GROUP 99 TRACK 99
DVD-
VIDEO
5 sec
JPEG
3 Press F G repeatedly to select the desired Repeat mode, then
press ENTER.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
30
DVD-RAM/RW/R
To cancel A-B Repeat Playback
Press D E to select AA-B xB, then press ENTER.
OFF:
Repeat playback is not performed.
NOTES:
● A-B Repeat Playback may not work properly depending on the
type of disc being used.
ALL REPEAT:
The whole disc is played back repeatedly.
● The subtitles recorded around the A-B point may not appear.
● When the end of the item is reached before the end point is set,
the on-screen bar disappears from the TV screen. In such a
case, repeat the procedure from step 1.
TITLE REPEAT:
The current title is played back repeatedly.
DVD VIDEO
● The point B must be set at least 3 seconds after the point A.
● When playing back a DVD, A-B Repeat Playback is possible only
within the same title.
● AA-B xB cannot be selected during Program and Random
Playback.
OFF:
Repeat playback is not performed.
TITLE REPEAT:
The current title is played back repeatedly.
CHAPTER REPEAT:
● AA-B xB cannot be selected while stopped.
The current chapter is played back repeatedly.
Locating The Beginning Of A Desired Selection
Audio CD/Video CD/SVCD/JPEG/MP3
OFF:
Repeat playback is not performed.
ALL REPEAT:
You can locate the beginning of a title, chapter, group or track.
During playback or while stopped
The whole disc is played back repeatedly.
TRACK REPEAT*:
1 Press ON SCREEN twice to access the on-screen bar.
2 Press D E to select A9B, then press ENTER.
The current track is played back repeatedly.
* ATRACK REPEATB cannot be selected for JPEG discs.
To clear the on-screen bar
Press ON SCREEN.
3 Press F G to select the desired item, then press ENTER.
● Skip this step for Video CD/SVCD and Audio CD.
To cancel Repeat Playback
Repeat the above procedure from step 1, select AOFFB in step 3,
then press ENTER.
For DVD-RAM/RW/R, DVD VIDEO
ATITLE SEARCHB or ACHAPTER SEARCHB is selectable.
(However, only ATITLE SEARCHB is selectable while stopped.)
NOTES:
For JPEG, MP3
● Repeat Playback is not possible for a Video CD/SVCD with PBC
function.
AGROUP SEARCHB or ATRACK SEARCHB is selectable. (However,
only AGROUP SEARCHB is selectable while stopped.)
● Repeat Playback may not work properly depending on the type of
the disc being used.
● It is possible to use Mode Lock function. (A pg. 76)
For Video CD/SVCD, Audio CD
ATRACKB is selectable.
NOTE:
A-B Repeat Playback
Settings that are selectable during playback and stop mode differ
depending on the type of disc and search used.
GROUP 99
CHAPTER 99
EACH 179:59
5
CINEMA
You can repeat the desired part.
DVD-
VIDEO
During playback
TITLE SEARCH
CHAPTER SEARCH
1 Press ON SCREEN twice to access the on-screen bar.
2 Press D E to select AA-B xB.
4 Press the number keys to enter the desired item number, then
press ENTER.
● Playback starts from the selected section.
Examples:
3 Press ENTER at the beginning of the desired part you want to
repeat (point A). The elapsed playing time of the point A
appears.
A To select track 5, press the number key A5B.
B To select track 15, press the number key A1B and A5B.
C To select track 25, press the number key A2B, then A5B.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
DVD-
VIDEO
If you have specified a wrong selection
Press RETURN on the remote control and repeat the above
procedures from step 2.
A
1 : 25 : 58
B
:
:
4 Press ENTER at the end of the desired part you want to repeat
(point B). The elapsed playing time of the point B appears.
● The selected part of the disc (between point A and B) is played
repeatedly.
To clear the on-screen bar
Press ON SCREEN.
NOTES:
● When A7B is displayed on the TV screen in step 4, the chapter
you have selected is not contained in the disc, or chapter search
does not work on the disc.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
DVD-
● Before you press ENTER, playback may start automatically when
you enter the section’s number depending on the disc.
● This function is not possible for a Video CD/SVCD with PBC
function.
VIDEO
A
1 : 25 : 58
B
1 : 40 : 00
To clear the on-screen bar
Press ON SCREEN.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
31
Simulated Surround Effect
CABLE/DBS
TV DVD
It is possible to get a simulated surround effect from your stereo
system. You can enjoy the virtual surround sound with your 2-
channel stereo system.
0-9
1 Press ON SCREEN twice to access the on-screen bar.
CANCEL
2 Press D E to select A
B, then press ENTER.
● A3D-ONB appears above the selected item and Simulated
Surround Effect is activated.
● Each time you press ENTER, A3D-ONB appears and disappears
alternately.
ENTER
FGDE
RETURN
T
S
TITLE 99
DVD-
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
I
CLEAR
VIDEO
ON SCREEN
To clear the on-screen bar
Press ON SCREEN.
To cancel the simulated surround effect
Press ENTER to clear A3D-ONB from the screen.
NOTES:
● Simulated Surround Effect works correctly only when playing
back a title recorded in multichannels.
● Simulated Surround Effect does not affect the DVD VIDEO
bitstream signal from the [DIGITAL AUDIO OUT] connectors.
● When Simulated Surround Effect is activated, the settings of
AANALOG AUDIO OUTB and AD. RANGE CONTROLB are
disabled. (A pg. 70)
● Simulated Surround Effect cannot be activated under the
following conditions:
● When the HDD deck is in the recording mode.
● When the HDD or DVD deck is in the timer standby mode.
● When a disc containing both the Dolby Digital 5.1CH and 2CH
sound formats is playing back a scene that is not in the 5.1CH
sound format.
Time Search
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a program (DVD-RAM,
DVD-R, DVD-RW, DVD VIDEO and HDD) or a disc (Video CD/
SVCD and Audio CD).
1 Press ON SCREEN twice to access the on-screen bar.
2 Press D E to select Aj9B, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
CHAPTER 99
EACH 0:00
CINEMA AUTO
Adjusting The Picture Quality
DVD-
VIDEO
3 Press the number keys to enter the time, then press ENTER.
Playback starts from the specified time.
Example:
You can obtain optimal picture quality by selecting an appropriate
picture mode.
To play back from a point 12 (minutes): 50 (seconds) elapsed.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press D E to select A
B, then press ENTER. The pop-up
TIME
TIME
TIME
TIME
TIME
window appears under the selected item.
TITLE 99 CHAPTER 99 EACH 0:00
CINEMA AUTO
Press 1
Press 5
Press 2
Press 0
DVD-
VIDEO
If you have specified a wrong selection,
Press RETURN on the remote control and repeat the above
procedures from step 2.
3 Press F G to select the desired option, then press ENTER.
NORMAL:
Normally select this option.
To clear the on-screen bar
Press ON SCREEN.
CINEMA:
Suitable for a movie disc, etc.
NOTES:
SHARP:
● When A7B is displayed on the TV screen in step 3, you have
selected a point that exceeds the recording time of the disc.
● Some DVD VIDEO discs do not contain time information, and it is
not possible to use the Time Search function. In such cases, A7B
is displayed on the TV screen as well.
Clearer, sharper-edged picture when viewing images with lots
of flat, same-colored surfaces such as cartoons.
SOFT:
Select this option when too much noise appears.
● This function is not possible for a Video CD/SVCD with PBC
function.
To clear the on-screen bar
Press ON SCREEN.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
32
4 Press I. Playback starts in the programmed order.
● When all of the programmed tracks have been played back,
Program Playback stops, but the programmed information
remains.
Setting The Progressive Mode
● To add tracks to the end of the program, perform steps 1
You can obtain optimal picture quality by selecting whether the content on
the disc is processed by field (video source) or by frame (film source).
through 3.
To clear the on-screen bar and the contents of the program
Press ON SCREEN.
1 Set the unit to the progressive scan mode. (A pg. 76)
2 Press ON SCREEN twice to access the on-screen bar.
To cancel Program Playback
Press D E to select APRGMB, then press ENTER.
3 Press D E to select A
B, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99 CHAPTER 99 EACH 0:00
3D-ON CINEMA
NOTE:
Program Playback is not possible depending on the type of disc.
AUTO
Random Playback
DVD-
VIDEO
4 Press F G to select the desired option, then press ENTER.
AUTO:
You can play back all the tracks on the disc in random order.
While stopped
This mode automatically detects film and video content for
progressive playback. When film content is found, flag
detection is used to invoke playback of film data in full screen.
When video content is found, pictures from multiple fields are
used to detect sections with movement, and then this
movement undergoes advanced image processing for output of
sharp, detailed progressive images without any reduction in
image quality where movement occurs. Normally, operation in
this mode is recommended.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press D E to select ARNDB, then press ENTER. Playback starts
in random order.
TRACK 99
EACH 0:00
CINEMA
VCD
FILM:
To clear the on-screen bar
Press ON SCREEN.
Suitable for playing back a progressive scanned film source
disc.
To cancel Random Playback
VIDEO:
Perform steps 1 and 2.
Suitable for playing back a video source disc. The outlines on
the played back pictures will be soft.
NOTE:
The same track will not be played back more than once during
Random Playback.
To clear the on-screen bar
Press ON SCREEN.
Select The Switching Interval Of The Slide Show
Program Playback
You can control the switching interval of the slide show.
You can program up to 30 tracks (Video CD/SVCD or Audio CD) to
play back in the desired order.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press D E to select A
B, then press ENTER. The pop-up
While stopped
window appears under the selected item.
1 Press ON SCREEN twice to access the on-screen bar.
GROUP 99 TRACK 99
2 Press D E to select APRGMB, then press ENTER. The program
table appears under on-screen bar.
5 sec
JPEG
TRACK 99
EACH 0:00
CINEMA
VCD
3 Press F G to select the desired option, then press ENTER.
● Each time you press F G, the interval changes as follows:
5 sec Y 10 sec Y 15 sec Y 20 sec Y 25 sec Y 30 sec Y
(Back to the beginning)
3 Press the number keys to
enter the track numbers in the
desired order.
USE [0-9] KEYS TO SELECT TRACK
To clear the on-screen bar
Press ON SCREEN.
Examples:
A To select track 5, press the
number key A5B and ENTER.
B To select track 15, press the
number key A1B and A5B.
NOTE:
JPEG files are played back as a slide show. It may take more time
to display an image with larger file size.
Program Total Time
C To select track 25, press the number key A2B and A5B.
If you have specified a wrong selection
Press CANCEL(L). The last selection is erased.
Or press CLEAR (o). The whole selection is erased.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
33
8 Press F G to select your country code, then press ENTER.
● If you do not need to change your country code, jump to 10.
● See ACountry/Area Code List for Parental LockB (A pg. 82)
Parental Lock
9 Press the number keys to enter the same password as in
step 6 above, then press ENTER.
10Press SET UP to complete the setting.
This function restricts playback of DVD VIDEO discs which contain
violent (and other) scenes according to the level set by the user.
For example, if a movie which includes violent scenes supports the
parental lock feature, such scenes which you do not want to let
children view can be cut or replaced by other scenes.
NOTE:
Remember your password, or make a note of it.
To Change The Settings
You can change the Parental Lock settings later.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD so that the DVD lamp lights up on the unit.
1 Perform steps 1 to 3 of ATo Set Parental Lock For The First
TimeB to access the APARENTAL LOCKB screen before
continuing.
To change the level
CABLE/DBS
2 Press F G to select APARENTAL LEVELB, then press ENTER.
3 Press F G to select the desired level, then press ENTER.
To change the country code
TV
DVD
DVD
4 Press F G to select ACOUNTRY CODEB, then press ENTER.
0-9
5 Press F G to select your country code, then press ENTER.
● See ACountry/Area Code List for Parental LockB (A pg. 82).
6 Press the number keys to enter the same password as in
step 6 of ATo Set Parental Lock For The First TimeB, then press
ENTER.
ENTER
FGDE
7 Press SET UP to complete the setting.
NOTE:
If you forget your password, enter A8888B in step 6.
To Temporarily Release Parental Lock
When you set the Parental Lock level strictly, some discs may not
be played back at all. When you insert such a disc and try to play it
back, the confirmation screen appears on the TV screen, asking
you whether you want Parental Lock to be temporarily released or
not.
SET UP
1 Load a disc.
● If the disc is rated higher than the selected level, the
confirmation screen appears.
To Set Parental Lock For The First Time
While stopped
2 Press D E to select AYESB, then press ENTER.
● If you select ANOB, you cannot play back that disc.
3 Press the number keys to enter the same password as in
step 6 of ATo Set Parental Lock For The First TimeB, then press
ENTER.
● When you enter the correct password, the Parental Lock is
released and the unit starts playback.
● If you enter a wrong password, AENTRY ERRORB appears on
the TV screen. Enter the correct password.
1 Press SET UP to access the Main Menu screen.
2 Press D E to select ADVD VIDEO SET UPB, then press G.
3 Press D E to select
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
INITIAL SET UP
APARENTAL LOCKB, then
press G.
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LOCK DISC PLAY SET UP
PARENTAL LEVEL
COUNTRY CODE
NONE
US
● If you have successively entered wrong password three times,
AENTRY ERROR CAN NOT CHANGE PASSWORDB appears
on the TV screen. In such a case, press ENTER. The disc will
stop. Then play back the disc again, and try the procedure
again from step 1.
SET UP
EXIT
ENTER
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
SELECT
4 Press F G to select
APARENTAL LEVELB, then
press ENTER.
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
INITIAL SET UP
NOTE:
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LOCK DISC PLAY SET UP
If you forget your password, enter A8888B in step 3.
PARENTAL LEVEL
COUNTRY CODE
NONE
US
5 Press F G to select the
desired level, then press
ENTER.
● The smaller the value of level
is, the more restrictive the
Parental Lock level becomes.
SET UP
EXIT
ENTER
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
SELECT
● Select ANONEB to cancel the restriction.
6 Press the number keys to enter your desired four-digit number,
then press ENTER.
● If you made a mistake, enter a correct number again.
7 Press F G to select ACOUNTRY CODEB, then press ENTER.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
34
7 Press o twice to stop recording.
● It takes about 10 seconds to end the writing session when you
stop recording.
Basic Recording
NOTES:
● It is recommended to format a DVD-RAM disc before use if you
use the disc on this unit for the first time.
● When using a brand-new DVD-RW disc, format the disc either in
VR mode or in Video mode. (A pg. 74)
● Recordings made on DVD-R/RW disc must be finalized to play
back on other DVD players. Perform AFinalize A Disc (DVD Deck
Only)B (A pg. 75).
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● You can record up to 99 programs and 99 play lists on each disc.
● Some programs can only be recorded one time.
● When recording is started, an index of the first part of recording is
automatically recorded (A pg. 50). To delete the index, refer to
page 52.
ATTENTION:
It is not possible to record programs on a DVD-R disc which has
already been finalized.
● Recording sometimes may stop or cannot be performed even if
there is enough available capacity remaining on the disc.
● It is not possible to record on both DVD and HDD simultaneously.
DV/HDD/DVD REC MODE
Recording Mode
MPEG2 format is used as recording format. As a guide for picture
quality, the AbpsB unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
o
I
WR
CH +/-
CABLE/DBS
TV DVD
The recording modes for a 4.7 GB disc are set as follows:
DVD
Recording amount
(approx.)
Maximum recording
time (approx.)
Recording mode
0-9
XP
SP
LP
EP
10 Mbps
5 Mbps
1 hour
2 hours
4 hours
6 hours
CH +/-
2.5 Mbps
1.6 Mbps
ENTER
60-360
(A pg. 36)
1 – 6 hours
The amount varies
depending on the
selected time.
I
FR
420
480
7 hours
8 hours
R
o
W
REC MODE
● For details on FR mode, refer to AFree Rate FunctionB (A pg. 36)
1 Load a recordable disc.
● For details, refer to APlacing A DiscB (A pg. 10).
2 Press DV/HDD/DVD on the unit repeatedly or DVD on the
remote so that the DVD lamp lights up on the unit.
3 Press CH +/- or the number keys to select the channel you
wish to record.
4 Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes
as follows:
XP N SP N LP NEP N FR (60-360*, 420, 480)
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5-minutes interval by
pressing D E repeatedly after selecting AFR60–FR360B. To change the
value in 30-minutes interval, press and hold D E.
● For details on the recording mode, see the right column.
5 Press R on the unit to start recording. Or while holding R, press
I on the remote control.
● The DVD recording lamp lights up on the unit.
6 Press R and W on the remote control simultaneously to pause
recording.
● To resume recording, press R and I simultaneously.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
35
Instant Timer Recording (ITR)
Recording Features
This easy method lets you record for 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
1 Press R on the unit to start recording.
2 Press R again to engage the ITR mode.
● Turn on the unit.
● On the front display panel, A0:30B appears.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DV/HDD/DVD on the unit repeatedly or DVD on the
remote so that the DVD lamp lights up on the unit.
3 If you want to record for more than 30 minutes, press R to
extend the time. Each press extends recording time by 30
minutes.
NOTES:
● You can only perform ITR using the R button on the unit.
DV/HDD/DVD
● When the recording capacity becomes full during timer recording
or Instant Timer Recording, the unit automatically performs
ARelief RecordingB (A pg. 48).
Watch Another Program While Recording On The Unit
While recording is going on, you can watch another program on
the TV. It does not interfere with recording.
R
DISPLAY
1 Turn on the TV.
CABLE/DBS
2 Select the desired channel to watch on the TV using your TV’s
TV
DVD
TV / VIDEO
remote control.
DVD
Elapsed Recording Time And Disc Remaining Time
Indication
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
CH +/-
Elapsed recording time N Disc remaining time N Clock N (Back
to the beginning)
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of
disc remaining times for all recording modes appears on the TV
screen.
REMAIN
DISPLAY
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
36
Free Rate Function
Second Audio Recording
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set A2ND
AUDIO RECORDB to AONB. (A pg. 72)
To record the entire program, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the program to be recorded and either the remaining
disc space or the specified recording time (from 60 minutes to 480
minutes).
NOTES:
When the channel is changed on the unit;
● The AMONOB indicator appears on the screen for about 5
seconds if the program is a monaural broadcast.
● The ASTEREOB indicator appears on the screen for about 5
seconds if the program is a stereo broadcast.
● Both ASTEREOB and ASAPB indicators appear when a stereo
program is accompanied by SAP sound.
8 To record the entire program within the actual remaining
disc space (DVD deck only)
Select AFR (JUST)B in a recording mode selection procedure.
● Note that this function is available only for timer programming
recording (A pg. 46, 48) and dubbing from HDD to DVD
(A pg. 57).
● Both AMONOB and ASAPB indicators appear when the main audio
on the monaural broadcast is accompanied by SAP sound.
8 To record the entire program by specifying the desired
recording time
Select AFR60–FR360B, AFR420B or AFR480B in a recording mode
selection procedure. (A pg. 34, 37, 46, 48)
8 To record a 25-min. long daily program five times just on
the same DVD disc for example
Perform AVCR Plus+ Timer ProgrammingB (A pg. 46) procedure.
Be sure to set the recording mode to AFR125B and set Weekly/
Daily Rec Function to AMON-FRIB in step 8 to fit the total recording
time to the whole disc space.
A: 1st
B: 2nd
Blank
C: 3rd
D: 4th
E: 5th
When the same program is recorded in SP mode instead of in
AFR125B, the 5th program cannot be recorded.
A: 1st
B: 2nd
C: 3rd
Blank
D: 4th
E: Blank (20 min.)
NOTES:
● You can program this unit to timer-record, regardless of the disc
remaining time. When the disc remaining time is not enough, the
unit performs ARelief RecordingB (A pg. 48). To avoid this, make
sure of the disc remaining time before setting timer programming.
(Example) If you programmed to timer-record for 60 minutes in
SP mode on a 120-minute disc, the disc remaining time would be
30 minutes in XP mode, 60 minutes in SP mode, 120 minutes in
LP mode, 180 minutes in EP mode, and 240 minutes in FR480
mode. Timer-recording will not complete beyond these remaining
times.
● The maximum recording time of FR (JUST) mode is the same as
the recording time of FR480 mode. When timer programming a
long program in FR (JUST) mode on a disc whose remaining
time is short, it is recommended to check the disc remaining time
in FR480 mode to see if the remaining time is enough for the
program.
● Even if more than one program are timer programmed in FR
(JUST) mode, only the first one is recorded.
● In order to ensure that the recording fits on the disc, this feature
may leave a slight non-recorded section at the end of the disc.
● There may be some noise and sound disturbance at the point on
the disc where the unit switches the mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
37
Pause recording on HDD deck
Basic Recording
It is not possible to pause recording. Pressing W initiates Live
Memory Playback.
However, it is still possible to pause recording only when recording
the channels of external sources (AL-1B, AF-1B and ADVB). While
holding R, press W on the remote. To resume recording, while
holding R, press I on the remote.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
No operation can be made with the buttons on the unit.
ATTENTION:
Recording Mode
The HDD on the unit requires approximately 20 seconds to start
up after the unit has been turned on, during which no operation
can be made.
MPEG2 format is used as recording format. As a guide for picture
quality, the AbpsB unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
HDD lamp
DV/HDD/DVD
Recording mode
Maximum recording time (approx.)
XP
SP
34 hours
69 hours
138 hours
209 hours
300 hours
CH +/-
R
o
LP
CABLE/DBS
EP
TV
DVD
FR480
HDD
● For details on FR mode, refer to AFree Rate FunctionB (A pg. 36)
NOTE:
0-9
The maximum recording time stated in the above table are the
approximate time under unused condition.
CH +/-
I
o
R
W
REC MODE
1 Press DV/HDD/DVD on the unit repeatedly or HDD on the
remote so that the HDD lamp lights up on the unit.
2 Press CH +/- or the number keys to select the channel you
wish to record.
3 Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes
as follows:
XP N SP N LP NEP N FR (60-360*, 420, 480)
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5 minutes interval by
pressing D E repeatedly after selecting AFR60–FR360B. To change the
value in 30 minutes interval, press and hold D E.
● For details on the recording mode, see the right column.
4 Press R on the unit to start recording. Or while holding R, press
I on the remote control.
● The HDD recording lamp lights up on the unit.
5 Press o twice to stop recording.
● Pressing o once displays the confirmation message to stop
recording. Press o again to terminate recording.
NOTES:
● Continuous recording for over 48 hours is not possible.
● It is not possible to record on both DVD and HDD simultaneously.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
38
Watch Another Program While Recording On The Unit
While recording is going on, you can watch another program on the
TV. It does not interfere with recording.
Recording Features
● Turn on the unit.
1 Turn on the TV.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DV/HDD/DVD on the unit repeatedly or HDD on the
remote so that the HDD lamp lights up on the unit.
2 Select the desired channel to watch on the TV using your TV’s
remote control.
Elapsed Recording Time And Disc Remaining Time
Indication
HDD lamp
DV/HDD/DVD
During recording, press DISPLAY on the remote control or the unit
repeatedly until the desired indication appears on the front display
panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time N Disc remaining time N Clock N (Back
to the beginning)
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of
disc remaining times for all recording modes appears on the TV
screen.
CH +/-
R
DISPLAY
CABLE/DBS
TV
DVD
TV / VIDEO
HDD
Second Audio Recording
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set A2ND
AUDIO RECORDB to AONB. (A pg. 72)
CH +/-
NOTES:
When the channel is changed on the unit;
● The AMONOB indicator appears on the screen for about 5
seconds if the program is a monaural broadcast.
● The ASTEREOB indicator appears on the screen for about 5
seconds if the program is a stereo broadcast.
● Both ASTEREOB and ASAPB indicators appear when a stereo
program is accompanied by SAP sound.
REMAIN
DISPLAY
● Both AMONOB and ASAPB indicators appear when the main audio
on the monaural broadcast is accompanied by SAP sound.
Instant Timer Recording (ITR)
This easy method lets you record for 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
1 Press R on the unit to start recording.
2 Press R again to engage the ITR mode.
● On the front display panel, A0:30B appears.
3 If you want to record for more than 30 minutes, press R to
extend the time. Each press extends recording time by 30
minutes.
NOTES:
● You can only perform ITR using the R button on the unit.
● When the recording capacity becomes full during timer recording
or Instant Timer Recording, the unit is automatically shut off.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
39
Basic Playback
Playback Features
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD so that the HDD lamp lights up on the unit.
DV/HDD/DVD
CABLE/DBS
TV
DVD
HDD
o
I
W
MARK
CABLE/DBS
TV
DVD
HDD
I
S
T
O/SLOW
-
N/SLOW +
W
o
-
v
w
JUMP
JUMP +
ON SCREEN
ENTER
I
o
W
Variable Speed Search
During playback, press N for forward variable speed search, or
O for reverse variable speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press I.
Reverse
O
N
Forward
Reverse
Slow Motion
3 steps
ATTENTION:
Reverse Search Reverse
Normal
Play
Slow Motion
3 steps
ForwardSearch
5 steps
● It may take a few seconds to start playback. This is not a
malfunction.
4 steps
Play
1
116
● Forward/reverse high-speed search and other operations
cannot be performed while playback is stopped.
-
½
-
¼
-
60
15
-60 -15 -5 -3
-1
1
1.5
3
5
½
¼
16
NOTE:
1 Press DV/HDD/DVD on the unit repeatedly or HDD on the
You can hear the (normal) audio track only during 1.5x speed
search.
remote so that the HDD lamp lights up on the unit.
2 Press I to start playback.
Still Picture/Frame-By-Frame Playback
● The Library Database Navigation also enables you to search
and select the desired programs. (A pg. 51)
1 Press W to pause during playback.
3 Press W to pause playback.
2 Press SLOW – (O) or SLOW + (N) to activate frame-by-
● To resume normal playback, press I.
frame playback.
4 Press o to stop playback.
● Each press of SLOW – (O) or SLOW + (N) advances/
reverses the still picture frame by frame.
● To resume normal playback, press I.
NOTE:
When the Library Database Navigation screen appears, choose a
thumbnail image of the desired title on the TV screen, then press
ENTER. (A pg. 51)
Slow Motion
1 Press W to pause during playback.
2 Press SLOW – (O) or SLOW + (N) for 2 or more seconds.
● Each press of SLOW – (O) or SLOW + (N) increases the
slow motion speed for each direction.
Skip Search
During playback, press v.
● Each press initiates an approximately 30-second period of fast-
motion playback. Normal playback resumes automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
40
Instant Replay
You can move back the playback position slightly.
Press w on the remote control or INSTANT REPLAY on the unit.
● Each press skips back for approximately 7 seconds and resumes
playback.
Marking Positions To Play Back Again Later
It is possible to mark positions (up to 999 points) where you want to
play back once again later, and start playback from a marked
position. Marking onto the disc when recording is helpful to locate
a start point when you play back the disc later.
● Pressing while paused skips back for approximately 7 seconds
and resumes pause.
To mark positions:
During playback, press MARK at
positions you want to mark.
● AMARKB appears on the TV screen.
You can easily locate the marked
positions using S or T when
you play back the disc.
1.5x Speed Playback
You can play back a title quickly. The sound will also be played
back faster than normal speed during 1.5x speed playback.
1.5x speed playback cannot be performed during recording on
HDD or DVD.
To delete the marked positions:
While paused, press S or T to
locate a marked position you want to
delete, then press MARK.
● Crossed AMARKB appears on the
TV screen, and the marked position
is deleted.
1 Press O to locate the point to start 1.5x speed playback from.
2 Press I to resume playback.
3 Press N once.
● Pressing ON SCREEN displays AX1.5B on the top right corner of
the screen.
NOTE:
NOTE:
When the unit is connected with a digital audio device using an
optional optical cable, set ADIGITAL AUDIO OUTB to APCM ONLYB.
(A pg. 28)
When a monaural program changes to a stereo program while
recording, a mark signal is automatically recorded.
Jump Search
You can locate a scene ahead or behind the current one by
jumping scenes according to selected time intervals (A pg. 72)
during playback (or Live Memory Playback).
Press JUMP – or JUMP +.
● To advance forward or back, press JUMP – or JUMP +
repeatedly within 5 seconds of each press to continue jump.
● Depending on the time from where you want to start jump search,
the first press of JUMP – or JUMP + will not necessarily lead to a
jump of the selected time interval. The first press will lead to a
jump to the nearest quarter points of an hour (15 min/ 30 min/ 45
min/ 00 min). The subsequent jumps will then be in accordance
to the selected time interval.
● When you cannot advance any further (beginning or end of
program reached), the message AUNABLE TO GO BACK ANY
MOREB appears on the screen and the on-air screen resumes. In
such a case, press S, O or o.
Example:
Playback search when jump interval is set to 15 MIN jumps.
Taking for instance, you want to start jump search 40 minutes after
the beginning of the program. Pressing JUMP – or JUMP + will
result in a jump to the scene at the 30 minutes point or 45 minutes
point respectively as illustrated below. At the subsequent press, the
scene will jump to the 15 minutes point or 1 hour point respectively,
according to the selected time interval, which in this case is A15
MINB.
Time counter
40 min
0 min
1 h 15 min
30 min
15 min
45 min
1 h
Beginning of program
Current scene
End of program
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DV DECK
EN
41
1 Load a cassette. Make sure the window side is up, the rear
label side is facing you and the arrow on the front of the
cassette is pointed toward the unit.
Basic Playback
● Do not apply too much pressure when inserting.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● If the erase protection switch is set to ASAVEB, playback begins
automatically. It takes about 15 seconds until the playback
picture appears. However, when APOWER SAVEB is set to
AONB (A pg. 72), playback will not begin automatically even
though a cassette with its erase protection switch set to ASAVEB
is inserted.
DV/HDD/DVD
I
● The unit’s power comes on automatically.
2 Press DV/HDD/DVD on the unit repeatedly or DV on the remote
so that the DV lamp lights up on the unit.
3 Find the program start point. If the tape is advanced past the
start point, press O. To go forward, press N.
4 Press I to start playback.
N
O
o
M
5 Press o to stop playback.
CABLE/DBS
TV DVD
● To eject the cassette, press M (DV).
Clean the video heads using a dry cleaning cassette
- M-DV12CL - when:
● No picture during playback.
DV
● Block noise appears during playback.
● AUSE CLEANING CASSETTEB appears on the screen.
NOTE:
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or humidity
● in a dusty environment
● flaw, dirt or mould on video tapes
● continuous usage for a long time
o
Usable cassettes
● Cassettes marked P can be used with the DV deck.
● Tapes recorded in the DVCAM format can be played.
O
o
N
NOTE:
When you record a tape on the DV deck with the recording speed
set to ALPB, it is recommended to play back that tape back on this
DV deck. Digital video recorder from other manufacturers may not
be able to play back the tape properly.
Accidental erasure prevention
To prevent accidental recording on a recorded cassette, set its
erase protection switch to ASAVEB. To record on it later, set the
switch to ARECB.
Erase protection switch
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DV DECK
EN
42
Skip Search
Playback Features
During playback, press v.
● Each press initiates an approximately 30-second period of fast-
motion playback. Normal playback resumes automatically.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DV/HDD/DVD on the unit repeatedly or DV on the
remote so that the DV lamp lights up on the unit.
Instant Replay
During playback, press
w
on the remote control or
INSTANT REPLAY on the unit. The unit rewinds the picture a little
(about 7 seconds) and resumes playback.
CABLE/DBS
Next Function Memory
TV
DVD
The Next Function Memory AtellsB the unit what to do after rewinding.
Before continuing, make sure the unit is in the Stop mode.
DV
1
For Automatic Start Of Playback
Press O, then press I within 2 seconds.
Soundtrack Selection
Your unit is capable of recording two soundtracks (L and R) and
will play back the one you select.
During Playback
Pressing AUDIO changes the soundtrack as follows:
TRACK
I
N
USE
O
On-Screen Display
W
L+R
Both sounds on the left channel and
the right channel are mixed and
played back
DISPLAY
AUDIO
L
Sound on the left channel is played
back
R
Sound on the right channel is played
back
Time Code
ATTENTION:
In the search, still, slow-motion or frame-by-frame playback
mode, a slight mosaic effect appears on screen.
During recording, a time code is recorded on the tape. This time
code is used to confirm the position on the tape when playing back
or editing a tape.
Variable Speed Search
During playback, press N for forward variable speed search, or
O for reverse variable speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press I.
1 Press DISPLAY on the remote control or the unit until the time
code on the tape appears on the front display panel and the TV
screen.
● Each time you press DISPLAY, the indication changes as
follows:
Tape remaining time N Time code N Clock time N (Back to
the beginning)
Reverse
O
N
Forward
Reverse
Slow Motion
1 step
Reverse Search
3 steps
Slow Motion
1 step
ForwardSearch
3 steps
Normal Play
1
-
1
5
-
12
-
-
1
2
4
12
4
2
5
Still Picture/Frame-By-Frame Playback
1 Press W to pause during playback.
2 Press W to activate frame-by-frame playback.
● To resume normal playback, press I.
Slow Motion
1 Press W to pause during playback.
2 Press and hold W for 2 seconds, then release. Press W and
release again to return to still picture.
● Press N for forward slow motion or O for reverse slow
motion.
● To resume normal playback, press I.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIVE MEMORY PLAYBACK ON HDD/DVD DECK
Recording/playback Status Display
CABLE/DBS
EN
43
Live Memory Playback
TV
DVD
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DV/HDD/DVD on the unit repeatedly to select the HDD
or DVD deck.
LIVE
NAVIGATION
Press NAVIGATION to display Library Database
Navigation menu, then choose a program to
play back. (A pg. 50)
This unit records pictures onto the hard disc and DVD-RAM disc,
instead of video tapes, then plays back the pictures recorded on
the disc. This makes it possible to achieve high-speed writing and
read-out that has not been possible with conventional VCRs,
enabling recording and playback simultaneously.
o
ON SCREEN
High-speed spin
Live Memory Playback status can be checked by
pressing ON SCREEN to display the bar meter on
the superimpose display. The current status is
superimposed on the TV screen. (A pg. 16, AWhen
using Live Memory playbackB)
Recording
(High-speed writing)
Playback
(High-speed read-out)
It is called ALive Memory PlaybackB to start playback of the
program being recorded, with a time-lag between a recording point
and a playback point, as shown in the figure below.
NOTES:
● Live Memory Playback could be performed approximately 30
seconds after recording has started on the DVD-RAM disc.
However, for HDD, Live Memory Playback is possible right after
recording has started.
Current playback point
(Live Memory Playback)
● Although high-speed search up to approximately 30 seconds
before the current recording point is possible during Live Memory
Playback, once the current recording point is reached, the unit
resumes normal playback and maintains a delay of
approximately 30 seconds so that recording and playback can
continue.
● When using Live Memory Playback during timer recording,
playback continues even after the end of the recording.
● When using Live Memory Playback during timer recording,
playback is automatically stopped just before recording starts,
and then recording starts when the time arrives for the next timer-
program.
Current recording position
Recording start point
(Recording point)
Recording
continues
Playback
continues
0
1 hour
30 min.
Currently elapsed recording time
Not only can this unit play back a program previously recorded
while recording or timer recording another program, but the unit
also allows you to play back from the beginning of a program while
continuing to record the same program.
● It is impossible to perform ITR even if you press R during Live
Memory Playback. (A pg. 38)
Press o to display the program being recorded, then perform ITR
settings.
● Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
● Live Memory Playback cannot be performed while recording the
source from DV input. (A pg. 60, ADV Dubbing (HDD & DVD
Deck Only)B)
● When LIVE CHECK is pressed to display the picture currently
being recorded, the picture size may not be correct.
● Press R or LIVE to stop Live Memory Playback.
● Live Memory Playback cannot be performed even if the ALIVE
MEMORYB in AHDD SET UPB is set to other than AOFFB, as
temporary recording on HDD stops during recording on DVD.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIVE MEMORY PLAYBACK ON HDD/DVD DECK
EN
44
F N
Buttons To Be Used During Live Memory Playback
● Each press of the button during playback advances the
playback speed in 4 steps in the forward direction.
Available only when paused
● Each press of the button advances the still picture frame by
frame.
● Pressing down for 2 or more seconds advances playback at 1/
16 times the normal speed. Then, each press of the button
advances slow-motion at 1/16 times, 1/4 times and 1/2 times
the normal playback.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to select the desired deck for Live Memory
Playback.
CABLE/DBS
G o
TV
DVD
● Pressing once during Live Memory Playback or RetroActive
Recording returns to the screen on air.
● Pressing twice during recording stops recording and returns to
the screen on air.
HDD
DVD
H W
● Pressing once pauses playback (still picture playback).
● Pressing repeatedly advances the still picture frame by frame.
I JUMP –
A
Each press of the button during Live Memory Playback jumps
back for the selected time interval and resumes playback.
(A pg. 40, AJump SearchB)
B
J JUMP +
C
D
Each press of the button during Live Memory Playback jumps
forward for the selected time interval and resumes playback.
(A pg. 40, AJump SearchB)
E
G
F
H
K v
I
J
K
L
It is useful when skipping over unwanted sections.
● Pressing once skips forward for approximately 30 seconds and
resumes playback.
● Pressing repeatedly skips forward continuously as many times
as pressed.
M
L w
It is useful when watching sports programs, etc.
● Each press skips back for approximately 7 seconds and
resumes playback.
● Pressing repeatedly skips back for approximately 7 seconds
continuously as many times as pressed.
A LIVE
Returns to on air program screen. When a confirmation
message appears by pressing this button during timer
programming or title editing, etc., follow the instruction to return
to the previous screen.
M LIVE CHECK
B NAVIGATION
You can check, for example, if the program you are recording
has already finished.
● Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
● Pressing successively clears the Live Check window and
displays only the picture currently being played back.
Displays Library Database Navigation menu. You can choose a
title to play back.
C S
● Pressing once skips back to the beginning of the chapter being
played back.
● Pressing down for 2 or more seconds during playback reverses
playback at 5 times the normal speed while pressed. Releasing
the button resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed.
D T
● Pressing once skips forward to the beginning of the next
chapter being played back.
● Pressing down for 2 or more seconds during playback
advances playback at 5 times the normal speed while pressed.
Releasing the button resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds advances playback at 1/
16 times the normal speed.
E O
● Each press of the button during playback advances the
playback speed in 5 steps in the reverse direction.
Available only when paused
● Each press of the button reverses the still picture frame by
frame.
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed. Then, each press of the button
reverses slow-motion at 1/16 times, 1/4 times and 1/2 times the
normal playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIVE MEMORY PLAYBACK ON HDD/DVD DECK
EN
45
Temporary recording for Live Memory (HDD deck only) Simultaneous Recording and Playback
This unit automatically records the channel being received, within
the specified range of time, to the reserved space on the hard disc.
The time range can be set for 30 minutes, 1 hour, and 3 hours.
(A pg. 71)
You can play back the previous part of the channel you are
recording or other programs available in the Library Database.
1 Press NAVIGATION. The Library Database Navigation screen
appears.
NOTE:
2 Press D E to select AORIGINALB, then press ENTER.
Previous temporary recordings will be overwritten since the unit is
always recording the channel being received. Thus, it is not
possible to play back TV programs recorded beyond the specified
range of time since they are already overwritten. To avoid this in
order to save titles, perform normal recording (A pg. 37), timer
recording (A pg. 46, 48), or RetroActive Recording (A pg. 45).
3 Press FGD E to select the desired title, then press ENTER.
● For DVD-RAM, playback starts from the beginning of the title if
ACONTINUOUS PLAYB in ADVD SET UPB is set to AONB
(A pg. 71).
4 Press D E to select the desired playback method
(ABEGINNINGB, ARESUMEB or AREPEATB), then press ENTER.
● Playback of the selected title begins automatically.
About limitation on temporary recording
The temporary recording for Live Memory is canceled in the
following cases, and will start all over again when it is to resume.
● When the power is turned off
● When the system is powered again after a power failure was
occurred
● When normal recording, timer recording or RetroActive
Recording is performed
● When the ALIVE MEMORYB setting is changed (A pg. 71)
● When tuner channel setting is performed (A pg. 22)
● When dubbing is performed by pressing DUBBING (A pg. 57)
● When ADVB is selected by pressing CH +/- (A pg. 60)
5 Press o to stop playback.
● The on-air screen resumes.
NOTES:
● You can use various playback features during Live Memory
Playback.
● To stop simultaneous playback, press o. The on-air screen
resumes. To stop actual recording, press o again.
Instant Replay
You can move back the playback position slightly during recording
or Live Memory Playback.
Press w on the remote control or INSTANT REPLAY on the unit.
RetroActive Recording (HDD deck only)
You can start recording from the previous part of the channel you
are currently watching (temporarily recorded on the background).
(A pg. 45, ATemporary recording for Live Memory (HDD deck
only)B)
8 DVD-RAM
● Pressing once during recording skips back for approximately 30
seconds and starts Live Memory Playback. While pressing once
during Live Memory Playback skips back for approximately 7
seconds and resumes playback.
1 Press S or O to locate the point to start recording from.
● Each subsequent press skips back for approximately 7 seconds
and resumes playback.
● Each press of O increases the reverse search speed.
2 Press R on the unit to start RetroActive Recording. Or while
holding R, press I on the remote control.
● Pressing while paused skips back for approximately 7 seconds
and resumes pause.
3 Press o to stop RetroActive Recording.
8 HDD
● The on-air screen resumes.
● Pressing during recording skips back for approximately 7
seconds and starts Live Memory Playback. While pressing during
Live Memory Playback skips back for approximately 7 seconds
and resumes playback.
NOTES:
● You cannot use RetroActive Recording for channels other than
the channel you are currently watching.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds
and resumes pause.
● Recording speed is automatically set to FR65 mode when
RetroActive Recording is started.
● Temporarily recorded data prior to the beginning of RetroActive
Recording is erased when RetroActive Recording started.
Resuming Playback (HDD deck only)
You can resume playback of a TV broadcast you were recording or
watching from the point you have paused.
1 Press W to pause a TV broadcast.
● Recording continues when recording.
2 Press I to start Live Memory Playback.
● Playback resumes from the paused position.
3 Press o to resume the on-air screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON HDD/DVD DECK
EN
46
7 The PlusCode number you entered and the matching timer-
recording information are displayed on the TV screen. Check
the program data.
VCR Plus+ Timer Programming
You can program this unit to timer record as many as 16 programs.
With the VCR Plus+ system, timer programming is greatly
simplified because each TV program has a corresponding code
number which your unit is able to recognize.
● To cancel this setting, press RETURN.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see AChanging VCR Plus+ SettingB (A pg. 73)
and set the Guide Channel number correctly.
You can use the remote control to enter the PlusCode number.
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
8 Press F G to select the desired recording option as required.
Press F G to select the desired setting, then press ENTER.
● AINPUT NAMEB (A pg. 51, AModify Title NameB)
● ACATEGORYB (A pg. 52, AModify CategoryB)
● AWEEKLY/DAILYB (A pg. 47, AWeekly/Daily RecordingB)
● AREC MODEB (A pg. 34, ARecording ModeB)
CABLE/DBS
TV
DVD
9 Press F G to select AOKB, then press ENTER to access the
Program Confirmation screen.
10Press D E to select AEXITB, then press ENTER to complete
0 – 9
timer programming.
● To program another timer, press D E to select ACONTINUEB,
then press ENTER.
PROG
● If APROGRAM OVERLAPPEDB appears on the TV screen,
delete or modify the programs.
ENTER
FGDE
NOTES:
● There may be cases that the VCR Plus+ Timer Programming
function prolongs the stop time of the programming.
● When two successive programs are recorded on a DVD-RW disc
with the VCR Plus+ Timer Programming function, the beginning
of the second one may be left off the recording.
● If the copy limited program is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
RETURN
DISPLAY
IMPORTANT:
If you have moved to a different area or if a broadcasting
station’s channel number has been changed, the wrong channel
number will be displayed on the VCR Plus+ program screen in
step 7. When this happens, set the correct Guide Channel
number for that station. (A pg. 73, AChanging VCR Plus+
SettingB)
1 Load a recordable disc if recording to DVD.
2 Press PROG to access the program top screen.
3 Press FGD E to select AVCR Plus+ PR.B, then press ENTER.
● When APROGRAM FULL DELETE UNWANTED TIMER
PROGRAMSB appears on the TV screen, you need to cancel
some of the reserved programs. (A pg. 49)
Cable Box and DBS Receiver Users
To timer record a satellite broadcast using the VCR Plus+
system:
A Perform AVCR Plus+ Timer ProgrammingB (A pg. 46).
B Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
4 Press the number keys to
1
23
PROGRAM > VCR Plus+ PR. (1/2)
enter the PlusCode number of
a program you wish to record.
OR
PLUS CODE NO.
1 2 3 4
SELECT WITH @
THEN PRESS [ENTER]
1
4
7
2
5
8
0
3
6
Press FGD E to select the
desired number key on the
screen, then press ENTER.
Repeat to enter all required
numbers.
PRESS [PROG] TO EXIT
9
DELETE
DELETE ALL
C Leave the cable box or DBS receiver’s power on.
RECORD TO
DVD
PROG
EXIT
ENTER
CONFIRM
SELECT
● If you have made a mistake, press FGD E to select ADELETEB
or ADELETE ALLB, then press ENTER and input the correct
number before you press ENTER again.
5 Press F G to select ARECORD TOB, then press ENTER. Press
F G to select the desired recording deck, then press ENTER.
6 Press FGD E to select ACONFIRMB, then press ENTER.
● If the number you entered is invalid, APLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRYB appears on the TV
screen. Input a valid PlusCode number.
● If AGUIDE PROGRAM IS NOT SET SET GUIDE PROGRAM
THEN RETRYB appears on the TV screen, set Guide Channel
Numbers manually. (A pg. 73)
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON HDD/DVD DECK
EN
47
Weekly/Daily Recording
You can record programs with one of the following weekly/daily
timer settings.
For the HDD deck
When you select a mode other than ONCE, the space on the hard
disk drive is saved for new recordings by overwriting previous
recordings. To prevent loss of a needed recording, backup
programs you wish to save by dubbing them to DVD discs before
overwriting previous recordings. Or save the title of weekly/daily
programs to avoid overwriting of a previous week/day. (A pg. 49)
ONCE (One Time Recording)
In this mode a program will not be automatically overwritten.
WEEKLY (OVERWRITE) (Weekly Recording/Weekly Overwrite)
When the set weekly program is broadcast, the program
recorded last week is automatically deleted and overwritten by
the new program. Save the title of each program you wish to
save, then the recorded program is saved and will not be
overwritten by the new program.
This week’s drama
Overwritten
Last week’s drama
MON-SUN (FOR A WEEK)/ MON-SAT (FOR A WEEK)/
MON-FRI (FOR A WEEK) (Daily Recording/Weekly Overwrite)
When the set weekly program is broadcast, the program
recorded on the same day last week is automatically deleted
and overwritten by the new program. Save the title of each
program you wish to save, then the recorded program is saved
and will not be overwritten by the new program.
This
week
MON TUE WED THU FRI
Overwritten
Last
MON TUE WED THU FRI
week
MON-SUN (OVERWRITE)/ MON-SAT (OVERWRITE)/
MON-FRI (OVERWRITE) (Daily Recording/Daily Overwrite)
When the set daily program is broadcast, yesterday’s program
is automatically deleted and overwritten by the new program.
Save the title of each program you wish to save, then the
recorded program is saved and will not be overwritten by the
new program.
Tuesday’s program
Overwritten
Monday’s program
For the DVD deck
ONCE (One Time Recording)
WEEKLY (Weekly Recording)
MON-SUN/ MON-SAT/ MON-FRI (Daily Recording)
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON HDD/DVD DECK
EN
48
8 Press F G to select ASOURCEB, then press ENTER. Press F G
to select the desired source.
Manual Timer Programming
9 Press F G to select ACHB, then press ENTER. Press F G to
You can program this unit to timer record as many as 16 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to
timer record the program.
select the desired channel.
10Press F G to select ACONFIRMB, then press ENTER.
11Set the other recording options as required.
● Refer to step 8 in AVCR Plus+ Timer ProgrammingB
(A pg. 46).
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
12Press F G to select AOKB,
2
PROGRAM > CALENDAR PR. (3/3)
then press ENTER to access
the Program Confirmation
screen.
01/08/03 WED 10:30PM
GARDENING
-
11:00PM
[EDUCATION]
DBS 100
FR360
28:00
1:00
SELECT WITH @
THEN PRESS [ENTER]
INPUT NAME
CATEGORY
GARDENING
EDUCATION
PRESS [PROG] TO EXIT
CABLE/DBS
13Press D E to select AEXITB,
then press ENTER to
complete timer
WEEKLY/DAILY
REC MODE
MON-FRI (FOR
A
WEEK)
TV
DVD
FR360
PROG
EXIT
ENTER
OK
SELECT
programming.
● To program another timer,
press D E to select ACONTINUEB, then press ENTER.
● If APROGRAM OVERLAPPEDB appears on the TV screen,
delete or modify the programs.
PROG
FGDE
NOTES:
● When two successive programs are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
ENTER
● If the copy limited program is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Cable box and DBS Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A Perform AManual Timer ProgrammingB (A pg. 48).
B Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
C Leave the cable box or DBS receiver’s power on.
1 Load a recordable disc if recording to DVD.
2 Press PROG to access the program top screen.
Relief Recording
3 Press FGD E to select ACALENDAR PR.B, then press ENTER.
● When APROGRAM FULL DELETE UNWANTED TIMER
PROGRAMSB appears on the TV screen, you need to cancel
some of the reserved programs. (A pg. 49)
When a program that is set for the DVD deck cannot be
recorded properly, the program is recorded to the HDD deck
instead in XP mode.
● If the remaining capacity of the hard disc is not sufficient, the
program is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
● If AJUSTB is selected for the recording mode, the current
recording mode for the DVD deck is applied.
4 Press FGD E to select the desired date, then press ENTER.
5 Press F G to select ARECORD
2
PROGRAM > CALENDAR PR. (2/3)
TOB, then press ENTER. Press
01/08/03 WED 10:30PM - 11:00PM
DBS 100
[MISC.
]
XP
F G to select the desired
recording deck, then press
ENTER.
SELECT WITH @
THEN PRESS [ENTER]
RECORD TO
HDD
START
STOP
SOURCE
CH
10:30PM
11:00PM
CATV
PRESS [PROG] TO EXIT
6 Press F G to select ASTARTB,
then press ENTER. Press F G
to set the desired start time,
then press ENTER.
100
PROG
EXIT
ENTER
CONFIRM
SELECT
● Each press of F G increases/decreases the start time in 1-
minute interval.
● To increase/decrease the start time in 30-minutes interval,
press and hold F G.
7 Press F G to select ASTOPB, then press ENTER. Press F G to
set the desired stop time, then press ENTER.
● Each press of F G increases/decreases the stop time in 1-
minute interval.
● To increase/decrease the stop time in 30-minutes interval,
press and hold F G.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON HDD/DVD DECK
EN
49
Check Programs
To check the whole list of programs
CABLE/DBS
TV DVD
1 Press PROG to access the program top screen.
2 Press FGD E to select APROGRAM LISTB, then press ENTER.
● The details of a selected program appear on the top of the
screen.
● The daily program of a title is listed as one program.
To check the list of programs by date
PROG
FGDE
1 Press PROG to access the program top screen.
2 Press FGD E to select ACALENDAR LISTB, then press ENTER.
3 Press F G to select the desired date, then press ENTER.
ENTER
Cancel And Change Programs
● Repeat steps in ACheck ProgramsB to select a program before
proceeding.
To cancel the program
1 Press FGD E to select ACANCELB, then press ENTER.
To modify the program settings
1 Press FGD E to select AMODIFYB, then press ENTER.
2 Change the settings of the desired recording options as
required.
● Refer to steps 4 – 13 in AManual Timer ProgrammingB
(A pg. 48).
To skip the weekly/daily programs to the next week/day
It is easy to temporarily cancel weekly/daily programs of a week/
day.
1 Press FGD E to select APROGRAM SKIPB, then press ENTER.
2 Press D E to select ASKIPB, then press ENTER.
To save the titles of weekly/daily programs (HDD Deck Only)
Use this function to avoid overwriting titles of weekly/daily
programs of a previous week/day.
1 Press FGD E to select ATITLE SAVEB, then press ENTER.
2 Press D E to select ASAVEB, then press ENTER.
NOTE:
This function is available only when the remaining capacity of the
hard disc is sufficient.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
50
Using Library Database Navigation system, you can easily modify
registered information, edit the title or play list, as well as search
for the beginning of each title.
Library Database Navigation
About registration of information
The following information is automatically registered for each title
when ordinary recording or timer recording is performed, then
stored in an area specified on the unit.
● index* (reduced pictures to show program titles)
● program title*
● category*
● date and time
● channel
● recording mode
The Library Database Navigation enables you to search and select
the desired titles recorded on the HDD deck and the DVD deck
very easily.
You can record up to 99 titles on a disc.
Each time a title is recorded, the information of the title is
registered for the Library Database Navigation automatically.
So, you can confirm the information of the titles recorded with the
Library Database Navigation screen. And, you can also select one
of the titles recorded using the Library Database Navigation.
The following screen appears as the Library Database Navigation
screen when you press NAVIGATION. You can move the arrow to
select the desired position on the screen by pressing FGD E on
the remote control.
● length of recording time
The items marked with an asterisk (*) can be easily modified and
registered again after recording by using Library Database
Navigation system.
The limitations of registration
You can register information up to 99 titles for the DVD deck and
200 titles for the HDD deck.
When the amount of information is at the limits of registration, you
cannot record new titles any more. In this case, you need to delete
old titles to register new one. (A pg. 52)
NAVIGATION > ORIGINAL
0026 [FISH WORLD
25/12/03 THU 10:00AM - 10:15AM
FROG WORLD
]
143 MIN
A
PR.
3
D
E
[HOBBY]
EP
SELECT WITH @
THEN PRESS [ENTER]
PRESS [NAVIGATION]
TO EXIT
NOTES:
B
C
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
ENTER
NAVIGATION
EXIT
SELECT
F
G
● When you move the title recorded on HDD to DVD, the icon will
be changed to
.
A Playback screen
● Sound of received channel may be interrupted while the Library
Database Navigation screen is displayed.
● The order of index which are displayed by pressing DUBBING
differs from the images displayed by pressing NAVIGATION or
EDIT.
● You cannot perform timer recording during editing of thumbnail
images or play lists by pressing EDIT. Press EDIT to clear the
Editing screen before performing timer recording.
(Indicates currently received TV program.)
B Guidance for operations
C Scroll bar
(Appears when there are over nine registered titles (or play
lists). The scroll bar only indicates that there are more titles (or
play lists) hidden off the current screen display. To show hidden
titles (or play lists), press FGD E repeatedly.)
D Recording information for the title indicated by the arrow
E Index list
(Thumbnail still of each title)
Thumbnail still is not to be played back.
F Index
:Indicates no index is registered.
:Indicates title in standby for timer recording.
:Indicates no title is registered.
G Icons
(Indicate the record condition of each title.)
The Icons and their meanings
This title is write-protected.
This title was recorded with timer recording.
This title is Weekly Recording/Weekly Overwrite.
This title is Daily Recording/Daily Overwrite.
This title is Daily Recording/Weekly Overwrite.
This title has not been played back.
W
D
D
NEW
This title is copy-protected.
This title can only be recorded once (copy-once title).
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
51
Scan For Beginning Of Title
Edit Original Information
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● Load a DVD disc to scan.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● Load a DVD disc to modify.
CABLE/DBS
TV
DVD
HDD
DVD
ATTENTION:
● It is not possible to modify discs recorded on DVD units from
other manufacturers.
● You cannot perform timer recording during editing the index by
pressing EDIT. Press EDIT to clear the editing screen before
performing timer recording.
CANCEL
ENTER
MEMO
NAVIGATION
Modify Index
FGDE
1 Press EDIT. The Editing screen appears.
I
2 (DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
o
W
3 Press FGD E to select AMODIFYB under AORIGINALB, then
press ENTER.
4 Press FGD E to select one title you want to modify, then press
ENTER.
5 Press D E to select AINDEXB, then press ENTER.
6 Press I to start playback. Press O or N to search for the
picture from the title, then press W.
● The pictures of the title appear
on the left window.
EDITING > MODIFY INDEX
You can scan the beginning of the title easily with the Library
Database Navigation.
25/12/03 THU 10:00AM - 10:15AM
FROG WORLD
TV
3
[OTHERS]
SP
INDEX
7 Confirm the arrow is on
1 Press NAVIGATION. The Library Database Navigation screen
AREPLACEB, then press
appears.
ENTER to register new index.
New index appears on the
right window.
● When you press ENTER with
the arrow on ARETURNB you
can return to the previous screen.
PROG.
1
0 : 01 : 03
2 Press FGD E to select AORIGINALB, then press ENTER.
SELECT IMAGE TO REPLACE WITH
ON REMOTE
RETURN
3 Press FGD E to select the
REPLACE
NAVIGATION > ORIGINAL
index (small pictures) of the
0026 [FISH WORLD
25/12/03 THU 10:00AM - 10:15AM
]
143 MIN
TV
3
desired title, then press
ENTER.
[HOBBY]
FROG WORLD
EP
SELECT WITH @
THEN PRESS [ENTER]
● When you want the plural titles
to be played back
PRESS [NAVIGATION]
TO EXIT
8 Press EDIT to return to the normal screen.
continuously, press MEMO
after selecting the desired title.
The numbers of the playback
order appear on the index. You can select up to 8 titles.
● When you want to correct the order, move the arrow to the
desired index and press MEMO. The number disappears and
the unit re-numbers the other programs automatically.
● When you want to cancel the order, press CANCEL(L).
NAVIGATION
EXIT
ENTER
Modify Title Name
SELECT
1 Perform steps 1 – 4 of AModify IndexB (A pg. 51) before
continuing.
2 Press FGD E to select ANAMEB, then press ENTER.
3 Press FGD E to select the
A
BC EDITING > MODIFY NAME
desired letter or command,
then press ENTER. Repeat
this process to complete the
name.
0026 [FISH WORLD
]
64 MIN
25/12/03 THU 10:00AM - 10:15AM
FROG WORLD
TV
3
[HOBBY]XP
4 Press D E to select
F ROG
W
OR L D
SELECT WITH @
THEN PRESS [ENTER]
NAVIGATION > ORIGINAL
ABEGINNINGB, then press
A
G
M
S
B
H
N
T
C
I
D
J
E
K
F
L
R
X
a
g
b
h
n
t
c
i
d
j
e
k
f
l
1
4
7
0
*
2
5
8
+
/
3
6
9
-
25/12/03 THU
SP
PRESS [EDIT]
TO EXIT
10:00AM
-
10:15AM TV
3
O
U
P
V
Q
W
m
s
o
u
p
v
q
w
r
x
ENTER.
FROG WORLD
● To correct a letter, press
FGD E to select ADELETEB,
then press ENTER.
● You can enter the letters up to
64.
[HOBBY]
Y
Z
y
z
=
SELECT WITH @
THEN PRESS [ENTER]
● To resume playback from the
point where playback was
previously stopped, press D E
to select ARESUMEB, then
press ENTER.
!
'
"
#
)
$
,
%
.
&
:
;
\
<
]
>
^
?
_
@
`
[
{
|
}
~
(
SELECT HOW TO PLAY BACK
EDIT
EXIT
ENTER
PRESS [NAVIGATION]
TO EXIT
CANCEL
DELETE
SAVE
SELECT
BEGINNING
RESUME
REPEAT
NAVIGATION
EXIT
ENTER
SELECT
4 Press FGD E to select ASAVEB, then press ENTER.
5 Press EDIT to return to the normal screen.
● To repeat playback of a
selected title, press D E to select AREPEATB, then press
ENTER.
5 Press W to pause playback.
● To resume normal playback, press I.
6 Press o to stop playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
52
Modify Category
Delete Unwanted Part Of The Title
(DVD-RAM & DVD-RW (VR mode) only)
You can delete unwanted part of the title.
1 Perform steps 1 – 4 of AModify IndexB (A pg. 51) before
continuing.
2 Press FGD E to select ACATEGORYB, then press ENTER.
1 Perform steps 1 – 2 of AModify IndexB (A pg. 51) before
continuing.
3 Press FGD E to select the
EDITING > MODIFY CATEGORY
desired category, then press
ENTER.
0026 [FISH WORLD
]
64 MIN
TV
[HOBBY]
2 Press FGD E to select ADEL SCENB, then press ENTER.
3
25/12/03 THU 10:00AM - 10:15AM
FROG WORLD
XP
3 Press FGD E to select one title whose unwanted part you want
MOVIES
MUSIC
DRAMA
SELECT WITH @
THEN PRESS [ENTER]
4 Press EDIT to return to the
to delete, then press ENTER.
ANIMATION
NEWS
SPORTS
DOCUMENTARY
EDUCATION
PRESS [EDIT]
TO EXIT
normal screen.
4 Press I to start playback. Press O or N to find the point
where you want the deletion to begin, then press W.
WEATHER
EDIT
EXIT
ENTER
HOBBY
ENTERTAINMENT ART
SELECT
5 Confirm the arrow is on AINB,
EDITING > ORIGINAL/DEL SCENE
21/12/03 SUN 5:30AM - 8:00AM
RALLY CAR
TV 12
[OTHERS]
then press ENTER.
SP
IN
Protect Title (DVD-RAM & DVD-RW (VR mode) only)
You can protect titles to prevent accidental erasure of the
important titles.
6 Press I to start playback.
Press O or N to find the
point where you want the
0 : 05 :15
OUT
0 : 06 :15
PROG.
1
0 : 01 : 03
deletion to end, then press W.
SELECT SCENE TO DELETE WITH
ON REMOTE
1 Perform steps 1 – 2 of AModify IndexB (A pg. 51) before
IN OUT
PREVIEW
OK
7 Press D E to select AOUTB,
continuing.
then press ENTER.
2 Press FGD E to select APROTECTB, then press ENTER.
● Select APREVIEWB, then press
ENTER to preview the edited title.
3 Press FGD E to select a title you want to protect, then press
ENTER.
8 Press D E to select AOKB, then press ENTER.
● If you do not want to delete the scene, press RETURN.
4 Press D E to select APROTECTB, then press ENTER. A
appears.
B
To modify the points
A Press RETURN.
B Repeat steps 4 – 8 as necessary.
● To cancel the protection, repeat 3 – 4 again. In step 4, select
ACANCEL PROTECTB, then press ENTER.
5 Press EDIT to return to the normal screen.
9 Press D E to select ADELETEB, then press ENTER. The
selected scene is deleted.
NOTE:
● To cancel the deletion, press D E to select ACANCELB, then
press ENTER.
All the titles on a disc will be deleted once the disc is formatted
even if they are protected titles. (A pg. 52)
10Press EDIT to return to the normal screen.
Delete Title
NOTES:
● There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
● Available recording capacity may not match the deleted part after
deletion.
You cannot record any more with Library Database Navigation
once the registered titles on the disc reach 99 titles for the DVD
deck and 200 titles for the HDD deck. Deleting unnecessary titles
after dubbing or other operations can increase remaining time and
available recording capacity. (For DVD-R discs, although it is
possible to delete recorded titles, available recording capacity
does not increase.) The deleted title is never resumed. Play lists
and title information in the unit’s library are also deleted.
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
3 Press FGD E to select ADELETEB under AORIGINALB, then
press ENTER.
4 Press FGD E to select one title you want to delete, then press
ENTER.
5 Press D E to select ADELETEB, then press ENTER.
● When you cancel the deletion, select ACANCELB, then press
ENTER.
6 Press EDIT to return to the normal screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
53
Divide Title (HDD deck only)
Edit Play List Information
1 Press EDIT. The Editing screen appears.
2 Press FGD E to select ADIVIDEB, then press ENTER.
3 Press FGD E to select a title to divide, then press ENTER.
4 Press I to start playback. Press O or N to locate a point to
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● Load a DVD disc to modify.
divide, then press W.
5 Confirm the arrow is on ADIVIDEB, then press ENTER.
● The first picture (start) of the newly created title appears in the
bottom right window.
● Select APREVIEWB, then press ENTER. The first several
seconds of the newly created title is played back, then the
playback pauses at the dividing point.
● To undo the division, press D E to select ARETRYB, then press
ENTER. Repeat the above procedure to locate another point to
divide.
ATTENTION:
● It is not possible to modify discs recorded on DVD units from
other manufacturers.
● You cannot perform timer recording during editing the index by
pressing EDIT. Press EDIT to clear the editing screen before
performing timer recording.
6 Press D E to select AOKB, then press ENTER.
7 Press D E to select ADIVIDEB, then press ENTER.
● Select ACANCELB, then press ENTER to return to the previous
screen.
CABLE/DBS
TV
DVD
8 Press EDIT to return to the normal screen.
HDD
DVD
NOTE:
There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
Modify Chapter
(HDD, DVD-RAM & DVD-RW (VR mode) only)
You can create and delete chapter marks in titles.
CANCEL
ENTER
MEMO
EDIT
NAVIGATION
DFGE
1 Perform steps 1 – 4 of AModify IndexB (A pg. 51) before
continuing.
T
I
N
S
O
2 Press FGD E to select ACHAPTERB, then press ENTER.
3 Press I to start playback.
EDITING > MODIFY CHAPTER
W
o
Press O or N, then press
CHAPTER 03/10
W at the positions you want to
mark.
0 : 07 : 01
4 Press D E to select AMARKB,
then press ENTER.
01 00 : 00 : 00
02 00 : 05 : 30
03 00 : 07 : 00
04 00 : 30 : 00
● To undo the marking, press
D E to select ARETRYB, then
press ENTER.
MARK
ERASE
RETRY
RETURN
● Repeat the above steps 3 and 4 to locate another point to mark.
Play List
5 Press S or T to select one chapter you want to delete,
press D E to select AERASEB, then press ENTER.
● To undo the deletion, press D E to select ARETRYB, then press
ENTER.
It is a collection of the scenes. A play list can be freely edited and
played back without ever changing any original recording data.
Using the random access of a disc (which allows video data to be
instantly read no matter where it is on the disc), a play list includes
information such as the timer counter for the playback start point
and end point, indexes for checking the contents of recorded data,
category information, and more. Playback according to a play list
you have created allows you to enjoy various combinations of
video images from a single title.
6 Press EDIT to return to the normal screen.
NOTE:
There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
54
Create Play List
Add scenes
1 Press EDIT. The Editing screen appears.
1 Perform steps 1 – 5 in AEdit ScenesB (A pg. 54) before
continuing.
2 (DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
2 Press FGD E to select ASEL. TITLEB, then press ENTER.
3 Perform steps 4 – 11 in ACreate Play ListB (A pg. 54).
3 Press FGD E to select ACREATEB, then press ENTER.
4 Press FGD E to select a title that includes scenes to be
Move Scenes
included in a play list, then press ENTER.
5 Press I to start playback. Press O or N to find the point
where you want the created play list to begin, then press W.
1 Perform steps 1 – 5 of AEdit ScenesB (A pg. 54) before
continuing.
6 Confirm the arrow is on AIN/
2 Press FGD E to select AMOVEB, then press ENTER.
3 Press F G to select a scene to move, then press ENTER.
EDITING > PLAY LIST/CREATE
TOTAL TIME
00 : 00 : 00
PAGE
OUTB, then press ENTER.
● The edit-in time is displayed on
the screen.
SCENE
PRO.
1 / 1
1
2
3
4
5
6
7
8
1
4 Press F G to select another scene to which the scene is to be
moved, then press ENTER.
● To cancel the move, press FGD E to select ARETRYB, then
press ENTER.
● To undo, press D E to select
ARETRYB, then press ENTER.
PRO.
1
0 : 00 :15
IN
OUT
7 Press I to start playback.
Press O or N to find the
point where you want the
IN/OUT
SEL. TITLE
MODIFY
DELETE
MOVE
PREVIEW
OK
RETRY
5 Perform steps 9 – 11 in ACreate Play ListB (A pg. 54).
created play list to end, then press W.
Delete Scenes
8 Confirm the arrow is on AIN/OUTB, then press ENTER.
1 Perform steps 1 – 5 of AEdit ScenesB (A pg. 54) before
● The edit-out time is displayed on the screen.
continuing.
● The edit-out point must come after the edit-in point.
2 Press FGD E to select ADELETEB, then press ENTER.
3 Press F G to select a scene to delete, then press ENTER.
4 Perform steps 9 – 11 in ACreate Play ListB (A pg. 54).
● Select APREVIEWB, then press ENTER to preview the play list.
9 Press FGD E to select AOKB, then press ENTER.
10Press D E to select AEXITB, then press ENTER
11Press EDIT to return to the normal screen.
Play Back Play List
NOTES:
● There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
● The title, index and category of the play list can be modified in the
same way as AORIGINALB. (A pg. 51)
● You can modify the play list that has just been created here by
adding, moving, or deleting unwanted parts to create a digest
edition, etc.
1 Press NAVIGATION. The Library Database Navigation screen
appears.
2 Press FGD E to select APLAY LISTB, then press ENTER.
3 Press FGD E to select the
NAVIGATION > PLAY LIST
index (small pictures) of the
0026 [FISH WORLD
026 CREATED 26/12/03 FRI
TEDDY BEAR 25/12
]
143 MIN
desired play list, then press
ENTER.
● When you want the plural play
lists to be played back
continuously, press MEMO
after selecting the desired play
lists. The numbers of the
[MOVIES]
001
004
007
002
005
008
003
SELECT WITH @
THEN PRESS [ENTER]
Edit Scenes
PRESS [NAVIGATION]
TO EXIT
006
009
1 Press EDIT. The Editing screen appears.
NAVIGATION
EXIT
ENTER
SELECT
2 (DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
playback order appear on the index. You can select up to 8 play
lists.
● When you want to correct the order, move the arrow to the
desired index and press MEMO. The number disappears and
the unit re-numbers the other play lists automatically.
● When you want to cancel the order, press CANCEL(L).
3 Press FGD E to select AMODIFYB under APLAY LISTB, then
press ENTER.
4 Press FGD E to select a play list to modify, then press ENTER.
5 Press FGD E to select ASCENEB, then press ENTER.
6 Press FGD E to select AMODIFYB, then press ENTER.
4 Press D E to select ABEGINNINGB, then press ENTER. The
7 Press FGD E to select the start or end point of a scene to
playback starts.
modify, then press ENTER.
● Upon completing play list playback, the normal screen will
resume.
● The normal screen will also resume when o is pressed to stop
play list playback.
8 Perform steps 5 – 11 in ACreate Play ListB (A pg. 54).
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
55
Delete Play List
Edit Library Information
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
3 Press FGD E to select ADELETEB under APLAY LISTB, then
press ENTER.
Title information can be registered in the unit’s memory for up to
600 DVD discs, 2,000 titles. It is helpful when finding a desired title
(or play list) by sorting according to the sort options registered
during (or after) recording.
4 Press FGD E to select one play list you want to delete, then
press ENTER.
5 Press D E to select ADELETEB, then press ENTER.
● When you cancel the deletion, select ACANCELB, then press
ENTER.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
6 Press EDIT to return to the normal screen.
CABLE/DBS
NOTE:
TV
DVD
Even if a play list is deleted, the titles recorded and the library
information are not affected at all.
HDD
DVD
Modify Index
A Perform steps 1 – 4 of AEdit ScenesB (A pg. 54) before
continuing.
B Perform steps 5 – 8 of AModify IndexB (A pg. 51).
Modify Play List Name
A Perform steps 1 – 4 of AEdit ScenesB (A pg. 54) before
continuing.
NAVIGATION
ENTER
FGDE
B Perform steps 2 – 5 of AModify Title NameB (A pg. 51).
Modify Category
A Perform steps 1 – 4 of AEdit ScenesB (A pg. 54) before
continuing.
B Perform steps 2 – 4 of AModify CategoryB (A pg. 52).
Scan For Title From Library
1 Press NAVIGATION. The Library Database Navigation screen
appears.
2 Press FGD E to select the
NAVIGATION
appropriate sort button to sort
DVD NAVIGATION
the information, then press
ENTER.
ADATEB:
ORIGINAL
PLAY LIST
SELECT WITH @
THEN PRESS [ENTER]
PRESS [NAVIGATION]
TO EXIT
DVD LIBRARY
Sort by date
ADISC No.B:
Sort by disc number
ACATEGORYB:
Sort by category
ANAMEB:
DATE
DISC No.
NAME
ENTER
NAVIGATI
EXIT
CATEGORY
A
SELECT
Sort by name
● ADATEB and ADISC No.B are available for the DVD deck only.
3 Press FGD E to select the desired title, then press ENTER.
● Playback begins automatically after the selected title is located.
NOTE:
If a disc registered in the library is recorded or modified on DVD
units from other manufacturers, it may become impossible to
operate properly.
Register Disc
When a disc that is not registered in the library is loaded, a
message appears confirming if the disc should be registered. If
registering, perform the following procedure.
1 Press D E to select AREGISTERB, then press ENTER to confirm
the registration.
2 Press NAVIGATION to return to the normal screen.
NOTES:
● It is not possible to register discs formatted on devices other than
JVC’s DVD recorders.
● It is not possible to register discs recorded on devices other than
JVC’s DVD recorders.
● It is not possible to register discs when ASAVE AS LIBRARYB is
set to AOFFB. (A pg. 71)
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
56
Locating The Desired Group And Tracks
Playback With MP3/WMA/JPEG
Navigation
1 Load a disc.
2 Press NAVIGATION.
3 Press FGD E to select AORIGINALB, then press ENTER.
4 Press F G to select the
NAVIGATION > ORIGINAL
desired group, then press
GROUP
:
001/100
TRACK
:
001/100
0 : 07 : 01
This unit can play back discs that MP3/WMA sound files and JPEG
image files taken with digital still cameras or other devices are
recorded.
The MP3/WMA/JPEG Navigation enables you to search and select
the desired files recorded on CD-R/RW or CD-ROM discs very
easily.
ENTER.
● A list of files in the selected
group appears.
IT’S SHOWTIME ! ! /B’z
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
003. SEXY GUY/GOMAKI
CLUB
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
006. REASON/ASAMI
FOREIGN GROUP
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
5 Press F G to select the
desired item, then press
ENTER. The unit starts
playback from the selected
item.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD to select the DVD deck.
NAVIGATION > ORIGINAL
GROUP
:
001/100
TRACK
:
001/100
0 : 07 : 01
IT’S SHOWTIME ! ! /B’z
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
003. SEXY GUY/GOMAKI
CLUB
DANCE
004. HEY?/AYAYA
● The unit stops when all items
in the selected group are
played back.
EUROPE
005. DOOR TO TOMORROW/I WISH
006. REASON/ASAMI
FOREIGN GROUP
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
NAVIGATION > ORIGINAL
GROUP
:
001/100
TRACK
:
001/100
0 : 07 : 01
NOTES:
IT’S SHOWTIME ! ! /B’z
● If you press SELECT(I) instead of ENTER in step 4, the unit
starts playback from the first file of the group.
● JPEG files are played back as a slide show at the set intervals.
(A pg. 32)
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
003. SEXY GUY/GOMAKI
CLUB
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
006. REASON/ASAMI
FOREIGN GROUP
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
● If a file name includes any 2-byte character, the unit may not
show the file name correctly.
● The order of the groups and items shown in steps 4 and 5 may
differ from the order shown on your PC.
A Selected group number/total number of groups on the disc
B Selected file number/total number of files in the group that
contains the selected file
C Elapsed time (MP3 only)
D Name of the selected file
E Group name
F Selected file
NOTES:
● If there are more than 100 files, the rest of the files are not
displayed. In this case, press ON SCREEN to display them on
the TV screen.
● If both MP3 files and WMA files are recorded on the same disc,
WMA files cannot be played back as they are not displayed on
the navigation screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
57
● It is not possible to dub the following programs to DVD-R/RW
disc (Video mode):
● which contains more than one audio language.
● which is on the play list.
Dubbing
● which is edited (also RetroActive Recording).
● which is recorded in LP mode or FP155-FP240 mode.
● Recording may not be performed in the highest speed depending
on the characteristics of the disc used.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Load a recordable disc.
CABLE/DBS
TV
DVD
2 Press DUBBING to access the Dubbing Menu screen.
3 Press FGD E to select AHDDNDVDB, then press ENTER.
4 Press FGD E to select AHIGH SPEEDB, then press ENTER.
HDD
DV
DVD
5 Press FGD E to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
MARK
● You can select up to 8 original recordings and/or play lists.
● The recordable time of the disc is displayed on the bar meter.
For details, refer to AAbout Disc Remaining DisplayB (A pg. 59).
DUBBING
ENTER
FGDE
6 Press D E to select AEXECUTEB or AAUTO FINALIZEB, then
press ENTER to start dubbing.
NOTES:
● Play lists are dubbed as programs.
R
o
W
● In Video mode, if the selected play list includes the scenes
recorded in the different transfer rate, the dubbing is performed in
the highest transfer rate of the scenes in the selected play list.
● During dubbing, it is not possible to play back on HDD or DVD, or
to set timer programming.
ON SCREEN
● It is not possible to discontinue dubbing once it has been started.
Just Dubbing (From HDD To DVD)
By using Just Dubbing function, when dubbing all selected original
recordings and/or play lists, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the selected recordings and/or play lists to be dubbed
and the available disc space.
Auto Finalizing
When dubbing from a Mini DV or HDD to a DVD (Video mode)
disc, you can select whether to finalize the disc automatically
after dubbing has been completed.
1 Load a recordable disc.
It is also possible to create a disc in the desired playback format
when finalizing the disc. Each time the finalized disc is played
back, it will be played back in accordance to the setting you have
selected during finalization. For details, refer to ADISC TYPEB
(A pg. 71).
2 Press DUBBING to access the Dubbing Menu screen.
3 Press FGD E to select AHDDNDVDB, then press ENTER.
4 Press FGD E to select AJUSTB, then press ENTER.
5
Perform steps
5
–
6
of AHigh Speed Dubbing (From HDD To DVD)B.
NOTE:
NOTES:
With Auto Finalizing, the background after finalization will be the
same as that used during the previous finalization.
● Play lists are dubbed as programs.
● In Video mode, if the selected play list includes the scenes
recorded in the different transfer rate, the dubbing is performed in
the highest transfer rate of the scenes in the selected play list.
However, the lower transfer rate cannot be dubbed in the higher
transfer rate.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to AAbout Disc Remaining DisplayB (A pg. 59).
● During dubbing, it is not possible to play back on HDD or DVD, or
to set timer programming.
NOTES:
● It is not possible to dub copy-protected contents. An error
message will appear on the TV screen.
● It is not possible to dub simultaneously when timer
programming is set. Select either dubbing or timer
programming.
● The order of the index which are displayed by pressing
DUBBING differs from the images displayed by pressing
NAVIGATION or EDIT.
● It is not possible to discontinue dubbing once it has been started.
Manual Dubbing (From HDD To DVD)
It is possible to perform dubbing in the desired transfer rate.
High Speed Dubbing (From HDD To DVD)
It is possible to dub the original recordings and/or play lists on the
HDD deck to DVD discs. The dubbing is performed in high speed,
keeping the original transfer rate.
1 Load a recordable disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press FGD E to select AHDDNDVDB, then press ENTER.
4 Press FGD E to select AMANUALB, then press ENTER.
NOTES:
● After accessing the Dubbing Menu screen, it is not possible to
take out a disc.
5 Perform step 5 of AHigh Speed Dubbing (From HDD To DVD)B.
● It is not possible to dub copy-once titles in Video mode.
● When dubbing a copy-once title, the data will be moved from
HDD to DVD upon completing dubbing.
● When you cancel dubbing a copy-once title during dubbing, the
original recording on the HDD deck remains and the title copied
to a DVD disc is deleted.
The Manual Dubbing screen appears.
6 Press F G to select AREC MODEB, then press ENTER. Press
F G to select the desired option, then press ENTER.
7 Press G to select ACONFIRMB, then press ENTER.
8 Press D E to select AEXECUTEB or AAUTO FINALIZEB, then
● It is not possible to dub play lists which contain copy-once titles.
press ENTER to start dubbing.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
58
NOTES:
Dubbing From DVD To DV
It is possible to perform dubbing from the DVD deck to the DV
deck.
● In Video mode, if the selected play list includes the scenes
recorded in the different transfer rate, the dubbing is performed in
the highest transfer rate of the scenes in the selected play list.
However, the lower transfer rate cannot be dubbed in the higher
transfer rate.
1 Load the disc you want to dub onto the DVD deck, and a Mini
DV cassette with the erase protection switch set to ARECB to the
DV deck.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to AAbout Disc Remaining DisplayB (A pg. 59).
● During dubbing, it is not possible to play back on HDD or DVD, or
to set timer programming.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press FGD E to select ADVDNDVB, then press ENTER.
● It is not possible to discontinue dubbing once it has been started.
4 Press FGD E to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
Dubbing From HDD To DV
It is possible to perform dubbing from the HDD deck to the DV
deck.
● You can select up to 8 original recordings and/or play lists.
5 Press F G to select ASELECT RECORDING MODEB, then
press ENTER. Press F G to select the desired option, then
press ENTER. The confirmation screen appears.
1 Load a Mini DV cassette with the erase protection switch set to
ARECB.
6 Press F G to select ASELECT SOUND MODEB, then press
ENTER. Press F G to select the desired option, then press
ENTER.
● Sound mode selection is not available when dubbing a
DVD-RW (Video mode) or DVD-R disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press FGD E to select AHDDNDVB, then press ENTER.
4 Press FGD E to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
7 Press G to select ACONFIRMB, then press ENTER. The
● You can select up to 8 original recordings and/or play lists.
confirmation screen appears.
5 Press F G to select ASELECT RECORDING MODEB, then
press ENTER. Press F G to select the desired option, then
press ENTER.
8 Press DV so that the DV lamp lights up on the unit.
9 Press I to locate the point from where you want to start
dubbing, then press R and W simultaneously so that the DV
deck enters the record pause mode.
6 Press F G to select ASELECT SOUND MODEB, then press
ENTER. Press F G to select the desired option, then press
ENTER.
10Press DVD so that the DVD lamp lights up on the unit.
● The dubbing screen will appear.
7 Press G to select ACONFIRMB, then press ENTER. The
11Press D E to select AEXECUTEB, then press ENTER to
confirm.
confirmation screen appears.
8 Press DV so that the DV lamp lights up on the unit.
● To cancel the dubbing, press o then D E to select ACANCELB
and press ENTER to confirm.
9 Press I to locate the point from where you want to start
dubbing, then press R and W simultaneously so that the DV
deck enters the record pause mode.
12Upon completing dubbing, the tape stops and ADUBBING
COMPLETEDB appears on the TV screen. Press ENTER to
end.
10Press HDD so that the HDD lamp lights up on the unit.
● The dubbing screen will appear.
NOTES:
11Press D E to select AEXECUTEB, then press ENTER for
confirmation.
● It is not possible to dub play lists on DVD discs.
● It is not possible to dub Video CDs/SVCDs or Audio CDs.
● When dubbing is in progress, only o is functional.
● To cancel the dubbing, press o then D E to select ACANCELB
and press ENTER to confirm.
12Upon completing dubbing, the tape stops and ADUBBING
COMPLETEDB appears on the TV screen. Press ENTER to
end.
Original Dubbing (From DVD To HDD)
It is possible to dub the original recordings on DVD discs to the
HDD deck.
1 Load a disc you want to dub.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press FGD E to select ADVDNHDDB, then press ENTER.
4 Press FGD E to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
5 Press D E to select AEXECUTEB, then press ENTER to start
dubbing.
NOTES:
● It is not possible to dub play lists on DVD discs.
● It is not possible to dub pre-recorded DVD VIDEO discs.
● It is not possible to dub Video CDs/SVCDs or Audio CDs.
● It is not possible to discontinue dubbing once it has been started.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
59
9 Upon completing dubbing, the tape stops and ADUBBING
COMPLETEDB appears on the TV screen. Press ENTER to
end.
Dubbing From DV To HDD
(Dubbing An Entire Cassette)
● The tape will automatically be rewound.
It is possible to perform automatic dubbing of all the recorded
programs of a cassette from the DV deck to the HDD deck using
the AENTIREB dubbing.
NOTES:
● ASUPERIMPOSEB is automatically set to AOFFB. It will return to
AAUTOB after dubbing is completed.
1 Load the Mini DV cassette you want to dub. Make sure its erase
● The program information at the DV deck will not be dubbed.
● When there are blanks on the tape of more than 2 seconds, the
DVD deck will enter into pause mode. Dubbing will resume once
recorded portion is detected.
● Dubbing copyright guarded tape is not possible.
● When dubbing is in progress, only o is functional.
protection switch is set to ASAVEB.
● Set ADV AUDIO RECB to the appropriate mode. (A pg. 71)
2 Press DUBBING to access the Dubbing Menu screen.
3 Press FGD E to select ADVNHDDB, then press ENTER.
4 Select AENTIREB, then press ENTER.
5 Press F G to select ASELECT RECORDING MODEB, then
press ENTER. Press F G to select the desired option, then
press ENTER.
About Disc Remaining Display
When dubbing from HDD to DVD, the unit displays the time
information for dubbing by bar meter. By comparing the disc
remaining time and the necessary time for dubbing of the selected
items, it is possible to check if the dubbing can be performed
completely or not.
6 Press F G to select ASELECT SOUND MODEB, then press
ENTER. Press F G to select the desired option, then press
ENTER.
7 Press G to select ACONFIRMB, then press ENTER. The
When performing the High Speed Dubbing
confirmation screen appears.
Capacity of a disc
Remaining capacity
8 Press D E to select AEXECUTEB, then press ENTER for
confirmation.
● Once dubbing starts, it will continue dubbing until the end of the
tape is reached.
21%
● To cancel the dubbing, press o then D E to select ACANCELB
and press ENTER to confirm.
● If the tape is not rewind, the unit will start dubbing after
automatically rewinding the tape to the beginning.
Dark green: Length of already recorded item
Light green: Length of selected item
Yellow: Length of the item now being selected by arrow
Red: Excess over the capacity
9 Upon completing dubbing, the tape stops and ADUBBING
COMPLETEDB appears on the TV screen. Press ENTER to
end.
When performing the Just Dubbing
● The tape will automatically be rewound.
TOTAL 105MIN
NOTES:
● ASUPERIMPOSEB is automatically set to AOFFB. It will return to
AAUTOB after dubbing is completed.
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The total time of a loaded disc is displayed on the right of the bar
meter.
● When there are blanks on the tape of more than 2 seconds, the
HDD deck will enter into pause mode. Dubbing will resume once
recorded portion is detected.
● Dubbing copyright guarded tape is not possible.
● When dubbing is in progress, only o is functional.
When performing the Manual Dubbing
Dubbing From DV To DVD
MAX FR240
(Dubbing An Entire Cassette)
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The available highest transfer rate is displayed on the right of the
bar meter.
It is possible to perform automatic dubbing of all the recorded
programs of a cassette from the DV deck to the DVD deck using
the AENTIREB dubbing.
1 Load the Mini DV cassette you want to dub. Make sure its erase
protection switch is set to ASAVEB.
● Set ADV AUDIO RECB to the appropriate mode. (A pg. 71)
2 Press DUBBING to access the Dubbing Menu screen.
3 Press FGD E to select ADVNDVDB, then press ENTER.
4 Select AENTIREB, then press ENTER.
5 Press F G to select ASELECT RECORDING MODEB, then
press ENTER. Press F G to select the desired option, then
press ENTER.
6 Press F G to select ASELECT SOUND MODEB, then press
ENTER. Press F G to select the desired option, then press
ENTER.
7 Press G to select ACONFIRMB, then press ENTER. The
confirmation screen appears.
8 Press D E to select AEXECUTEB or AAUTO FINALIZEB, then
press ENTER for confirmation.
● Once dubbing starts, it will continue dubbing until the end of the
tape is reached.
● To cancel the dubbing, press o then D E to select ACANCELB
and press ENTER to confirm.
● If the tape is not rewind, the unit will start dubbing after
automatically rewinding the tape to the beginning.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
60
The following on-screen display for DV dubbing appears when
ON SCREEN is pressed while the channel has been set to ADVB.
DV Dubbing (HDD & DVD Deck Only)
0:00
FR360 00:00:00. 00
12bit
DV JVC
1:00
2:00
GR-DV3500
00:00:00. 00
DV
HDD
You can dub programs from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
L
–
R
GR-DV3500
SOUND1
NOTES:
1
2
DV
DV
● Use the DV cable VC-VDV 204U for connection.
● When you connect a PC to the [DV IN] connector, we do not
assure the normal operation of this unit.
A
B
C
A Remote control switch
To switch between the devices operable by the remote control
unit. The unit is operable when the remote icon (
Your unit
)
displayed faces to the left, while the DV device is operable
when the remote icon is facing to the right.
B Auto capture button
Select to start or pause the dubbing. If ENTER is pressed when
the DV device is in the pause condition, preroll editing* where it
is possible to dub with a start time that is highly accurate will be
activated. When the DV device cannot be operated from the
unit (such as in camera mode), proceed with normal recording
(A pg. 34, 37).
To [DV IN]
* Preroll editing refers to the playback after the DV tape is slightly
rewind. (For DV devices that do not support the –1x speed, the
rewinding time may be longer.)
C Sound monitor switch
Camcorder
DV cable
For selecting the desired sound format for dubbing.
(VC-VDV 204U)
(not supplied)
1 Connect a camcorder or DV equipment to the [DV IN]
connector on the unit’s front panel.
2 Press DV/HDD/DVD on the unit repeatedly or HDD on the
remote so that the HDD lamp lights up on the unit.
3 Press CH +/- to set the channel to ADVB.
4 Press ON SCREEN.
DV connector
● The on-screen display for DV dubbing appears.
DV equipment
5 Press D E to select
, then press ENTER to display
the remote icon (facing to the right) for the DV equipment.
6 Press REC MODE repeatedly to set the recording mode.
7 Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: I, N, O, o, W.
● To play back in slow speed (1/10 of the normal speed), press W
to pause playback, then press O or N.
● To play back frame-by-frame, press W to pause playback, then
press W repeatedly. Each press of W advances a frame.
● To change the playback direction, press O or N.
8 Press D E to select
, then press ENTER repeatedly
until the desired sound track appears on the TV screen.
SOUND1:
Select this to record the original stereo sound played back on
the connected DV equipment.
SOUND2:
Select this to record the dubbed stereo sound played back on
the connected DV equipment.
MIX:
Select this to record the sound of both ASOUND1B and
ASOUND2B.
● Note that this selection is not available when the source
program is recorded in 16BIT (48 kHz) mode.
9 Press D E to select
, then press ENTER. The
dubbing starts.
● Playback on the external DV equipment and recording on the
unit should start simultaneously.
● To pause dubbing, press D E to select
, then press
ENTER. Both the unit and the external DV equipment pause
dubbing. Pressing W on the unit also works the same way.
10Press D E to select
press o. The DV equipment stops.
11Press D E to select , then press ENTER.
, then press ENTER. Then
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
61
12Press o twice on the remote control to stop dubbing.
● Both the unit and the external DV equipment stop dubbing.
NOTES:
● Dubbing copyright guarded programs is not possible.
● Original DV information such as the recording date and time are
not recorded.
● The superimposed indication during the operation or dubbing is
not recorded.
● If the dubbing is paused while the channel is set to ADVB, you
cannot switch channels.
When you dub from DV equipment other than a
camcorder
A Perform step 1 to 4.
B Locate the point from where you want to start dubbing,
then stop on the DV equipment.
● If you pause the DV equipment in this step, a few
second’s still picture will be recorded at the beginning of
the recorded program.
C
Set the input mode to ADV INPUTB on the DV equipment.
● If you select an input mode other than ADV INPUTB,
unwanted pictures may be recorded at the beginning of
the recorded program.
D Perform step 9 to 12.
To skip unwanted part of the source picture
Press ENTER to stop both equipment, then press D E to select
.
Locate the point where you want to restart dubbing by pressing I,
N, or O, then press o.
Press D E to select
dubbing.
, then press ENTER to restart
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
62
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Edit From A Camcorder
1 Make connections.
You can use a camcorder as the source player and your unit as the
recording deck. If your camcorder has a DV IN/OUT connector,
you can use the camcorder as the recording deck and your unit as
the source player.
A If the camcorder has no S-VIDEO output connector:
^ connect the camcorder’s AUDIO/VIDEO OUT connectors to
the unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors
on the front panel.
● When using a monaural camcorder, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
B If the camcorder has an S-VIDEO output connector:
^ connect the camcorder’s AUDIO OUT and S-VIDEO OUT
connectors to the unit’s [AUDIO] and [S-VIDEO] input
connectors on the front panel.
A If the camcorder has no S-VIDEO output connector:
C If the camcorder has a DV IN/OUT connector:
^ connect the camcorder’s DV IN/OUT connector to the unit’s
[DV IN/OUT] connector.
Recorder
To [VIDEO/AUDIO
((MONO) L/R)] input
● When using your unit as the source player, refer to the
camcorder’s instruction manual for the recording procedure.
Audio/video cable
(not supplied)
2 Press DV/HDD/DVD on the unit repeatedly to select the
recording deck.
3 Press CH +/- to select AF-1B or ADVB.
● Set AFRONT AUX F-1B to AVIDEOB for the [VIDEO] input
connector, or AS-VIDEOB for the [S-VIDEO] input connector,
depending on the connector being used. (A pg. 72)
AUDIO/VIDEO OUT
Player
4 Press REC MODE repeatedly to set the recording mode.
5 Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
6 Press R on the unit to start recording. Or while holding R, press
B If the camcorder has an S-VIDEO output connector:
I on the remote control. The dubbing starts.
7 Press o on the unit, then stop playback on the camcorder.
NOTES:
● All necessary cables can be obtained from your dealer.
● Refer to the camcorder’s instruction manual for operating
procedure.
● The quality of dubbed picture becomes poorer than that of the
original.
To [S-VIDEO]
input
Recorder
To [AUDIO] input
● When you are editing through the [DV IN/OUT] connector, the
unit will stop if the player begins playing a blank portion of tape or
the signal is interrupted.
● When connecting the unit to a device equipped with a DV input
connector, be sure to use the optional DV cable (VC-VDV204U)
● To edit through the [DV IN/OUT] connector using the HDD or
DVD deck, refer to ADV Dubbing (HDD & DVD Deck Only)B
(A pg. 60).
S-video cable
(not supplied)
S-VIDEO
OUTPUT
Audio cable
(not
supplied)
AUDIO OUTPUT
Player
C If the camcorder has a DV IN/OUT connector:
Recorder/Player
To [DV IN]
DV cable
(VC-VDV 204VU)
(not supplied)
DV connector
Player/Recorder
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
63
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Edit To Or From Another Recorder
1 Make connections.
You can use your unit as the source player or as the recording
deck.
A When using your unit as the source player:
^ connect its [S-VIDEO/VIDEO/AUDIO OUTPUT] connectors
to the input connectors on another recorder.
B When using your unit as the recording deck:
^ connect its [S-VIDEO/VIDEO/AUDIO OUTPUT] connectors
on the front or rear panel to the output connectors on
another recorder.
NOTES:
● When using another recorder as the recording deck, refer to its
instruction manual.
● It is not possible to dub copy-protected contents. An error
message will appear on the TV screen.
● When connecting to another recorder with S-video connector,
set AREAR AUX L-1B or AFRONT AUX F-1B to AS-VIDEOB.
A When using your unit as the source player
2 Press CH +/- to select the external input.
TV receiver
● Select AF-1B when the source player is connected to the unit’s
[VIDEO/AUDIO] or [S-VIDEO/AUDIO] input connectors on the
front panel, and select AL-1B when it is connected to the unit’s
[VIDEO/AUDIO] or [S-VIDEO/AUDIO] input connectors on the
rear panel.
Player
Your unit
3 Press REC MODE repeatedly to set the recording mode.
4 Engage the Play mode on the source player.
5 Engage the Record mode on the recording deck.
6 Stop recording on the recording deck, then stop playback on
the source player.
NOTES:
● All necessary cables can be obtained from your dealer.
● When you use this unit as the source player for editing, be sure to
set ASUPERIMPOSEB to AOFFB before starting. (A pg. 72)
Another recorder
Recorder
B When using your unit as the recording deck
TV receiver
Player
Your unit
Another recorder
Recorder
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
64
1 Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
Digital Audio Dubbing
2 Place a disc on the unit and load an MD on the connected
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
digital audio device.
3 Select the audio to be dubbed.
However, it is not possible to dub copy-protected discs.
4 Start playback slightly before the actual point from where you
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
wish to start dubbing.
5 Press W to pause playback.
Example: Dubbing to an MD
Recorder
6 Select the input mode on the connected digital audio device.
7 Press I to start playback on the unit.
8 Start recording on the digital audio device.
9 Stop recording on the digital audio device. Then press o to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
Digital audio device
(MD deck, etc.)
Optical cable
(not supplied)
Coaxial cable
(not supplied)
To [DIGITAL
AUDIO OUT
(COAXIAL)]
To [DIGITAL AUDIO
OUT (OPTICAL)]
Player
Rear of unit
Note for connection:
Remove the protection cap from the optical
cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
65
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Audio Dubbing (DV Deck Only)
1 Connect an audio device to the unit’s [AUDIO] input connectors
on the front panel.
● When using a monaural audio device, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
This function allows you to record new audio, without erasing the
original audio, on a DV tape that was recorded with ADV AUDIO
RECB set to A12BITB (A pg. 71).
2 Load a Mini DV cassette with the erase protection switch set to
ATTENTION:
ARECB.
You cannot perform Audio Dubbing on a tape that was recorded
with ADV AUDIO RECB set to A16BITB (A pg. 71), on a tape that
was recorded at the ALPB speed, or on a blank tape.
3 Press DV/HDD/DVD on the unit repeatedly or DV on the remote
so that the DV lamp lights up on the unit.
4 Press CH +/- to select AF-1B.
5 Start playback slightly before the actual point from where you
Your unit
Recorder
wish to start dubbing.
6 Press W to pause playback.
7 Press AUDIO DUB. to engage the audio dubbing mode.
● Your unit enters the Audio Dubbing Pause mode.
● To perform Audio Dubbing with audio mixing, press AUDIO to
select AL+RB at this point. When using the DV deck as the
recording deck, also make sure that AAUDIO MODEB is set to
ASOUND1B (A pg. 71).
CH +/-
To [AUDIO]
input
AUDIO DUB.
* Audio Dubbing with audio mixing is not possible if you are using a
monaural audio component, or if you don’t have an audio mixer.
Audio cable
(not supplied)
8 Engage the audio device’s playback, then press I to start the
tape in the unit. Audio dubbing starts at this point.
● To stop dubbing temporarily, press W. Press I to resume
dubbing.
AUDIO OUT
9 Press o on the unit, then stop playback on the audio device to
CD player, etc.
end the audio dubbing.
NOTES:
● Once the Audio Dubbing starts, you cannot use the other deck.
● When monitoring the audio dubbed sound on the DV deck, set
AAUDIO MODEB to ASOUND2B (A pg. 71).
● When playing back an audio dubbed Mini DV tape on the DV
deck, set AAUDIO MODEB to ASOUND2B (A pg. 71).
● Audio dubbing is not possible using the [DV IN/OUT] connector.
● Audio dubbing is not possible on a blank portion of the tape.
CD player, etc.
Mixer output
Audio mixer
Recorder
Original sound
[AUDIO OUTPUT]
Your unit
CH +/-
To
[AUDIO]
input
AUDIO DUB.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
66
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Insert Editing (DV Deck Only)
1 Make connections.
Insert Editing replaces the pictures with new ones, while the audio
soundtrack remains unchanged. For Insert Editing, use your unit
as the recording deck.
A If the player has no S-VIDEO output connector:
^ connect the player’s AUDIO/VIDEO OUT connectors to your
unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on
the front panel.
ATTENTION:
B If the player has an S-VIDEO output connector:
^ connect the player’s AUDIO OUT and S-VIDEO OUT
connectors to your unit’s [AUDIO] and [S-VIDEO] input
connectors on the front panel.
Insert Editing is not possible with a Mini DV cassette recorded in
LP mode.
A If the player has no S-VIDEO output connector:
2 Load a Mini DV cassette with the erase protection switch set to
ARECB.
CH +/-
Recorder
Your unit
3 Press DV/HDD/DVD on the unit repeatedly or DV on the remote
so that the DV lamp lights up on the unit.
4 Press CH +/- to select AF-1B.
5 Press S, T and W to determine the edit-in point (the
beginning of the segment to be replaced).
● Be sure to engage the Still mode at the edit-in point.
To [VIDEO/AUDIO
((MONO) L/R)] input
INSERT
6 Press INSERT to engage the insert editing mode.
● Your unit enters the Insert Pause mode.
● The TV screen changes from the still picture to the input source
you are going to record.
Audio/video
cable
(not supplied)
7 Load the source cassette and play back the segment that is to
be inserted. When you reach the start of the section of the
source tape that you wish to insert, press I to start the tape in
your unit. Insert editing begins at this point.
8 Press o to stop recording on the DV deck to end insert editing.
AUDIO/VIDEO OUT
NOTES:
● Once the Insert Editing starts, you cannot use the other deck.
● All necessary cables can be obtained from your dealer.
● Insert Editing cannot be performed on a Mini DV cassette that
has had its erase protection switch set to ASAVEB.
● When Insert Editing is performed on a tape that has been
recorded on another video recorder, the inserted portion may
appear distorted.
● A small portion of the recording which precedes an insert edit
may become erased.
● Insert Editing is not possible using the [DV IN/OUT] connector.
● Insert Editing is not possible on a blank portion of the tape.
Another recorder
Player
B If the player has an S-VIDEO output connector:
Your unit
CH +/-
Recorder
INSERT
To [S-VIDEO]
To [AUDIO] input
input
S-video cable
(not supplied)
Audio cable
(not supplied)
S-VIDEO
OUT
AUDIO OUT
Another recorder
Player
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
EN
67
CABLE/DBS
Remote Control Functions
Remote Control 1/2/3/4 Code Switching
The remote control is capable of controlling four JVC video units
independently. Each of the units can respond to one of the four
codes (1, 2, 3 or 4). The remote control is preset to send code 3
signals because your unit is initially set to respond to code 3
signals. You can easily modify your unit to respond to code 1, 2 or
4 signals.
TV
DVD
TV / VIDEO
0 – 9
A
TV VOL +/-
CH +/-
TV MUTING
ENTER
● Slide the TV/CABLE/DBS/DVD switch to DVD.
SET UP
A
I
CABLE/DBS
TV
DVD
1 – 4
TV Multi-Brand Remote Control
Your remote control can operate the basic functions of your TV set.
In addition to JVC TVs, other manufacturer’s TVs can also be
controlled.
ENTER
● Turn off the TV using its remote control.
● Slide the TV/CABLE/DBS/DVD switch to TV.
IMPORTANT:
Although the provided remote control unit is compatible with JVC
televisions, as well as many other models, it may not work with
your TV, or in some instances, may have limited function
capability.
o
SET UP
● Keep pressing SET UP down during step 1.
1 Enter your TV’s brand code using the number keys, then press
ENTER.
2 Press A on the unit’s remote control to turn on the TV and try
operations (A step 3).
● Once you have set the remote control to operate the TV, you do
not have to repeat this step until you replace your remote
control’s batteries.
● Some brands of TVs have more than one code. If the TV does
not function with one code, try entering another.
● Keep pressing SET UP down during step 1.
1 Press the number key A1B for 1, A2B for 2, A3B for 3 or A4B for 4 to
change the remote control code, then press ENTER.
2 Press A on the unit to turn off the unit.
3 Press the corresponding buttons to operate the TV: A,
TV/VIDEO, CH +/-, TV VOL +/–, TV, number keys.
● For some brands of TVs, you must press ENTER after having
pressed the number keys.
3 Press I on the unit for over 5 seconds while the unit is turned
off. The code currently set appears on the front display panel.
4 Press o on the remote control to change the unit’s code. The
code currently set on the remote control blinks on the front
display panel for approximately 5 seconds, and is applied to the
unit.
NOTE:
When APOWER SAVEB is set to AONB (A pg. 72), it is not possible
to change the remote code.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
EN
68
BRAND NAME
CODE
CABLE BOX BRAND
CODE
JVC
01, 03
10
02
03
04, 11
05
ARCHER
01, 05, 17
01, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
02
01, 17
15, 16, 17, 21, 25
15
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
06
07
SAMSUNG
SANYO
SEARS
12
13
13
GENERAL INSTRUMENTS
HAMLIN
JASCO
01, 04, 06, 11, 12, 15, 28
10, 18, 23
15
TOSHIBA
ZENITH
08
09
JERROLD
NOVAVISION
OAK
01, 04, 06, 11, 12, 15, 28
02
07
PANASONIC
PULSER
RCA
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 23
01, 16, 17
05, 16, 24
02
Cable Box Or DBS Receiver Multi-Brand Remote
Control
Your remote control can operate the basic functions of your cable
box or DBS (Direct Broadcast Satellite) receiver set. In addition to
JVC cable boxes or DBS receivers, other manufacturer’s cable
boxes or DBS receivers can also be controlled.
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
07
SL MARX
05, 16, 17, 24, 25
13, 14
05, 15, 16, 17, 21, 24, 25
05, 16, 24
01, 04, 16
01, 17
● Slide the TV/CABLE/DBS/DVD switch to CABLE/DBS.
● Keep pressing SET UP down during step 1.
SPRUCER
STARGATE
TELEVIEW
TOCOM
1 Enter your cable box or DBS receiver’s brand code using the
number keys, then press ENTER.
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
16, 17, 25
03, 09, 22
03, 09, 22
2 Press A on the unit’s remote control to turn on the cable box
or DBS receiver and try operations (੬ step 3).
● Once you have set the remote control to operate the cable box
or DBS receiver, you do not have to repeat this step until you
replace your remote control’s batteries.
● Some brands of cable box or DBS receiver have more than one
code. If the cable box or DBS receiver does not function with
one code, try entering another.
DBS RECEIVER BRAND
CODE
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
51
51
41
40
3 Press the corresponding buttons to operate the cable box or
DBS receiver: A, CH +/-, number keys.
RCA (DSS)
● For some brands of cable box, you must press ENTER after
having pressed the number keys.
● The number keys may not function with some cable boxes.
IMPORTANT:
It may not work with your cable box, or in some instances, may
have limited function capability.
NOTES:
● It’s not possible to operate a cable box or DBS receiver that is not
equipped with a receiving window.
● It’s not possible to set the remote control for both your cable box
and a DBS receiver at the same time. You can only set the
remote control to operate one of these units at a time.
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM CONNECTIONS
EN
69
1 Connect the unit and a Dolby Digital Decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
NOTES:
● For Dolby Digital sound, set ADIGITAL AUDIO OUTB to ADOLBY
DIGITAL/PCMB. (A pg. 70)
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
● For DTS sound, set ADIGITAL AUDIO OUTB to ASTREAM/PCMB.
(A pg. 70)
CAUTIONS:
● This unit has a dynamic range of more than 110 dB with regards
to its Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to
the speakers may damage them.
● Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do
not place the speakers adjacent to the TV set as this can
adversely affect the playback picture.
Dolby Digital Decoder or
amplifier with built-in DTS
To DIGITAL AUDIO
input
Coaxial cable
(not supplied)
Optical cable
(not supplied)
To [DIGITAL
AUDIO OUT
(COAXIAL)]
To [DIGITAL AUDIO
OUT (OPTICAL)]
Rear of unit
Note for connection:
Remove the protection cap from the
optical cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
70
* The boldface settings below indicate the settings at your purchase.
Mode Set
AUDIO OUTPUT
8 DIGITAL AUDIO OUT ^ DOLBY DIGITAL/PCM / STREAM/
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
PCM / PCM ONLY
Set to the appropriate mode according to the type of the device
connected to [DIGITAL AUDIO OUT] connector.
DOLBY DIGITAL/PCM:
CABLE/DBS
Select this when you connect the digital input connector of a
Dolby Digital Decoder or an amplifier with a built-in Dolby Digital
Decoder.
TV
DVD
HDD
DVD
STREAM/PCM:
Select this when you connect the digital input connector of an
amplifier with a built-in DTS, Dolby Digital, or MPEG
multichannel decoder.
PCM ONLY:
Select this when you connect the linear PCM digital input of
other audio equipment (amplifier, MD or DAT deck, etc.).
ENTER
NOTES:
FGDE
● This setting also functions when HDD is active.
● If you watch or play back a title which contains multiple audio
languages, select APCM ONLYB in advance and choose main or
sub audio with AUDIO.
8 ANALOG AUDIO OUT ^ STEREO / DOLBY SURROUND
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
SET UP
STEREO:
AUDIO
Select this when listening to conventional two-channel stereo
audio with the unit’s [AUDIO OUTPUT] connectors connected
to a stereo amplifier/receiver or TV set, or in case you want to
record the audio from a DVD VIDEO disc to a Mini Disc, etc.
Various modes of this unit are categorized into menus nested in 2
levels shown in the following table. To change the settings of these
modes, find the desired mode in the menu (for details on each
menu, see pages 70 through 72), then follow the procedure below.
DOLBY SURROUND:
Select this when listening to multichannel surround audio with
the unit’s [AUDIO OUTPUT] connectors connected to an
amplifier/receiver with a built-in surround decoder or a surround
decoder.
DVD VIDEO SET UP
LANGUAGE SET (A pg. 20)
AUDIO OUTPUT (A pg. 70)
PARENTAL LOCK (A pg. 33)
DISC PLAY SET UP (A pg. 71)
8 D. RANGE CONTROL ^ NORMAL / WIDE RANGE / TV MODE
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a program
encoded in Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
HDD/DVD/DV SET UP
HDD SET UP (A pg. 71)
DVD SET UP (A pg. 71)
DISC SET UP (A pg. 74, 75)
DV SET UP (A pg. 71)
NORMAL:
FUNCTION SET UP
INITIAL SET UP
REC/PLAY SET UP (A pg. 71)
DISPLAY SET (A pg. 72)
VIDEO IN/OUT (A pg. 23, 72)
Normally select this setting to activate this function.
WIDE RANGE:
Select this to deactivate this function when you enjoy wide
dynamic range program.
TUNER SET (A pg. 22)
CLOCK SET (A pg. 21)
TV MODE:
Select this when you hear the sound through the TV’s
speaker(s).
● The procedure below shows how to set the desired option of the
A2ND AUDIO RECORDB mode as an example.
NOTES:
● This function has no effect on programs other than those
recorded in Dolby Digital format.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
● This function does not work when Simulated Surround Effect is
activated. (A pg. 31)
● The effect of ANORMALB and AWIDE RANGEB may not be
different depending on discs.
2 Press SET UP to access the Main Menu screen.
3 Press D E to select AFUNCTION SET UPB, then press G.
4 Press D E to select AREC/
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
INITIAL SET UP
PLAY SET UPB, then press G.
REC/PLAY SET UP
DISPLAY SET
VIDEO IN/OUT
8 OUTPUT LEVEL ^ STANDARD / LOW
XP MODE REC AUDIO
DOLBY DIGITAL
5 Press F G to select A2ND
AUDIO RECORDB, then press
ENTER.
You can lower the output level of analog audio to accommodate
the unit to the connected A/V equipment.
2ND AUDIO RECORD
JUMP TIME
OFF
15 MIN
STANDARD:
6 Press F G to select the
desired option, then press
ENTER.
Normally select this setting.
ENTER
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
SET UP
EXIT
LOW:
SELECT
The output level of analog audio is lowered.
7 Press SET UP to complete the
setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
71
DISC PLAY SET UP
ATTENTION:
When changing the settings in the ADV SET UPB menu while in
the DV deck mode, the unit will switch to HDD or DVD deck
mode. To proceed to DV deck after making the changes, press
DV/HDD/DVD on the unit repeatedly or DV on the remote control
to select the DV deck.
8 RESUME ^ OFF / ON / DISC RESUME
When this function is set to AONB or ADISC RESUMEB, you can use
the resume function. (A pg. 26)
OFF:
You cannot use the resume function.
ON:
DV SET UP
You can start playback from the resume point of the placed disc.
8 DV AUDIO REC ^12BIT / 16BIT
DISC RESUME:
This is the setting for sound mode before recording on a Mini DV
tape.
The unit retains a memory of the resume points of the last 30
discs played back, even though they have been ejected.
12BIT:
NOTE:
Enables Audio Dubbing later.
ADISC RESUMEB setting works on DVD VIDEO, VCD, SVCD and
already finalized DVD-R/DVD-RW (video mode) discs. For other
types of discs, the function under AONB setting will be applied even
if ARESUMEB is set to ADISC RESUMEB.
16BIT:
Audio Dubbing is not possible but the recorded sound quality is
higher than A12BITB.
8 AUDIO MODE ^ SOUND1 / SOUND2 / MIX
You can select the desired sound mode when playing back an
audio dubbed Mini DV tape.
HDD SET UP
8 LIVE MEMORY ^ OFF / 30 MIN / 1 HR / 3 HR
When this function is set to A30 MINB, A1 HRB or A3 HRB, you can
apply the selected time length to ATemporary recording for Live
Memory (HDD deck only)B (A pg. 45).
SOUND1:
Original recorded sound.
SOUND2:
Audio dubbed sound.
DVD SET UP
MIX:
8 SAVE AS LIBRARY ^ OFF / ON
Original recorded sound and audio-dubbed sound.
When this function is set to AONB, the recording information is
automatically stored in the library. For details, refer to AEdit Library
InformationB (A pg. 55).
NOTES:
● When AAUDIO MODEB is set to AMIXB, both the main and sub
audio will be audible for bilingual tapes.
● To select only the main audio or only the sub audio of bilingual
tapes, set AAUDIO MODEB to ASOUND1B.
8 CONTINUOUS PLAY ^ OFF / ON
When this function is set to AONB, multiple titles on a disc are
played back continuously one after another.
REC/PLAY SET UP
8 XP MODE REC AUDIO ^ DOLBY DIGITAL / LINEAR PCM
You can select the audio format when you record a title in XP
mode. When this function is set to ALINEAR PCMB, you can obtain
a high-quality audio sound.
8 VIDEO MODE RECORDING ASPECT ^ PRIORITIZE 4:3 /
PRIORITIZE 16:9
This is the setting for the aspect ratio used when you dub titles to
DVD discs in video mode. If the titles you want to dub are recorded
in both 16:9 and 4:3, you must select one aspect ratio.
DOLBY DIGITAL:
PRIORITIZE 4:3:
To record in Dolby Digital format.
If you select APRIORITIZE 4:3B, even a title recorded in 16:9 is
LINEAR PCM:
dubbed in 4:3.
To record in Linear PCM format.
PRIORITIZE 16:9:
If you select APRIORITIZE 16:9B, even a title recorded in 4:3 is
dubbed in 16:9.
8 MP3 & WMA / JPEG ^ MP3 & WMA / JPEG
You can select files to play back, when both MP3&WMA files and
JPEG files are recorded on a disc.
MP3 & WMA:
Select this to play back MP3/WMA files.
JPEG:
Select this to play back JPEG files.
8 DISC TYPE ^ MANUAL START / MENU STOP / AUTO
REPEAT
MANUAL START:
To be chosen when you want to playback the disc manually by
pressing I each time after the disc is read.
MENU STOP:
To be chosen when you want playback to stop each time a
menu screen is displayed. The unit automatically starts
playback after the disc is read.
AUTO REPEAT:
To be chosen when you want the disc to be played back
repeatedly each time it is played back. The unit automatically
starts playback after the disc is read.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
72
8 2ND AUDIO RECORD ^ OFF / ON
When this function is set to AONB;
If a SAP program is received, the SAP audio is recorded on L/R
tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on L/
R tracks.
8 ON SCREEN LANGUAGE
This unit offers you the choice to view on-screen messages in 3
different languages.
For details, refer to AOn-screen Language SetB (A pg. 20)
VIDEO IN/OUT
When this function is set to AOFFB, the SAP audio cannot be recorded.
8 MONITOR TYPE ^ 4:3LB / 4:3PS / 16:9AUTO / 16:9FIX
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
For details, refer to AMonitor SetB (A pg. 23).
NOTE:
When the channel is changed on the unit;
● The AMONOB indicator appears on the screen for about 5
seconds if the program is a monaural broadcast.
● The ASTEREOB indicator appears on the screen for about 5
seconds if the program is a stereo broadcast.
● Both ASTEREOB and ASAPB indicators appear when a stereo
program is accompanied by SAP sound.
8 FRONT AUX F-1 ^ VIDEO / S-VIDEO
Select the appropriate mode depending on the connector (F-1)
being used on the front panel.
● Both AMONOB and ASAPB indicators appear when the main audio
on the monaural broadcast is accompanied by SAP sound.
VIDEO:
To use the [VIDEO] input connector on the front panel.
S-VIDEO:
8 JUMP TIME ^ 15 MIN / 30 MIN / 1 HR
To use the [S-VIDEO] input connector on the front panel.
You can locate a scene ahead of or behind the currently viewed one
by jumping a selected time interval during playback (or Live Memory
8 REAR AUX L-1 ^ VIDEO / S-VIDEO
Select the appropriate mode depending on the connector (L-1)
being used on the rear panel.
Playback). For details, refer to
A
Jump Search
B
(
A
pg. 26, 40).
DISPLAY SET
VIDEO:
To use the [VIDEO INPUT] connector on the rear panel.
8 SUPERIMPOSE ^ AUTO / ON / OFF
When this function is set to AAUTOB, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (A pg. 20)
S-VIDEO:
To use the [S-VIDEO INPUT] connector on the rear panel.
AUTO:
To superimpose operational indications for approximately five
seconds just after the corresponding operation.
ON:
To turn on superimposed indications.
OFF:
To turn off superimposed indications.
NOTES:
● When you use this unit as the source player for editing, be sure to
set ASUPERIMPOSEB to AOFFB before starting. (A pg. 63)
● When you select AAUTOB, during playback, the operation mode
indicators may be disturbed depending on the type of disc being
used.
8 BLUE BACK ^ OFF / ON
When this function is set to AONB, the TV screen becomes all blue
when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals,
set this function to AOFFB.
8 DIMMER ^ BRIGHT / DIMMED
You can change the brightness of the front display panel.
BRIGHT:
Normally select this.
DIMMED:
To dim the front display panel. (Blue lamp on the front display
panel is turned off.)
8 POWER SAVE ^ OFF / ON
When this function is set to AONB, you can reduce the power
consumption while the unit is turned off.
NOTES:
● During Power Save mode ^
^ the front display panel will be turned off.
● Power Save does not work when ^
^ the unit is in the Timer mode.
● It takes some time for the unit to complete initialization after you
turn on the unit power, with AWAKE UPB blinking on the front
display panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
73
Guide Channel Number Set
Changing VCR Plus+ Setting
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
The VCR Plus+ programming system assigns a VCR Plus+ guide
channel to the TV channels and the cable channels. These guide
channel numbers are also called the VCR Plus+ channel codes.
Most TV listings have a section, usually a chart, indicating the
guide channel numbers assigned to each station.
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press D E to select AINITIAL SET UPB, then press G.
4 Press D E to select ATUNER
DVD VIDEO SET UP HDD/DVD/DV SET FUNCTION SET UP
INITIAL SET UP
To ensure that VCR Plus+ timer recording operates correctly, it is
necessary to set the “VCR Plus+ Guide Channel” for each station.
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, perform the following steps to
set the correct guide channel number.
SETB, then press G.
TUNER SET
CLOCK SET
AUTO CH SET
MANUAL CH SET
5 Press FGD E to select AGUIDE
CH SETB, then press ENTER.
GUIDE CH SET
11
12
3
NOTES:
ENTER
SET UP
EXIT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
● In many instances, the VCR Plus+ guide channel numbers for
cable and broadcast TV stations DO NOT match the channel
number on which it is received by your unit or cable box. Check
your TV listing, or contact your cable supplier for details.
● Many TV stations can be viewed on cable. Check your TV listing,
or contact your cable supplier for details.
SELECT
6 Press F G to select AGUIDE CH
SETB, then press ENTER.
11
12
13
INITIAL SET UP > GUIDE CH SET
GUIDE CH
CABLE CH
1
7 Press F G to select the Guide
Channel number for the desired
station as shown in the TV
-
-
listings. Then press ENTER.
● If you receive your channels
with a cable box and if you have
properly set your Controller,
RETURN
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
ENTER
SELECT WITH @
THEN PRESS [ENTER]
SET UP
EXIT
SELECT
PRESS [SET UP] TO EXIT
ACABLE CHB appears in place of ADVD CHB.
CABLE/DBS
8 Press F G to select ADVD CHB, then press ENTER. Press F G
to select the number of the unit’s channel position on which the
Guide Channel Number’s broadcast is received by the unit or
the DBS receiver. Then press ENTER.
TV
DVD
● Repeat steps 6 – 8 as necessary.
9 Press SET UP to complete the setting.
Guide Channel Number
“Guide Channel (GUIDE CH) Number” refers to the assigned TV
station numbers, according to broadcast area, for the VCR Plus+
timer recording. The Guide Channel Numbers can be found in
most TV listings.
ENTER
FGDE
SET UP
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
74
Format A DVD-RAM Disc
Format A Disc (DVD Deck Only)
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press D E to select AHDD/DVD/DV SET UPB, then press G.
4 Press D E to select ADISC SET
Some DVD-RAM/RW discs are unformatted.
Format the disc when you use an unformatted disc or you want to
delete all recordings and data on the disc.
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
INITIAL SET UP
DV SET UP
UPB, then press G.
HDD SET UP
DVD SET UP
DISC SET UP
FINALIZE
Video
CANC. FINALIZ.
5 Press FGD E to select
ATTENTION:
AFORMATB, then press
● When a disc is formatted, all recordings and data are erased. It
is impossible to restore them.
FORMAT
ENTER. Press D E to select
AOKB, then press ENTER.
● Never turn off the unit or disconnect the AC power cord while
ANOW FORMATTING...B is displayed on the TV screen.
ENTER
SET UP
EXIT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
6 Press D E to select
AEXECUTEB, then press
ENTER.
SELECT
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Load a DVD-RAM/RW disc to format.
Format A DVD-RW Disc
1 Perform steps 1 to 4 of AFormat A DVD-RAM DiscB as above
before continuing.
CABLE/DBS
2 Press FGD E to select AFORMATB, then press ENTER. Press
D E to choose AVR MODEB or AVIDEO MODEB, then press
ENTER when ADISC WILL BE FORMATTEDB appears on the
TV screen.
TV
DVD
AVR MODEB:
To be chosen when you want to record, erase, or edit data on
the disc repeatedly.
AVIDEO MODEB:
To be chosen when you want to erase all the data on the disc
once played back to record new data, or play back the disc on
other DVD players.
ENTER
FGDE
3 Press D E to select AEXECUTEB, then press ENTER.
NOTES:
● It is impossible to format Version 1.0 DVD-RW discs in Video
mode.
● It is impossible to format DVD-R discs.
● All the titles on a disc will be deleted once the disc is formatted
even if they are protected titles. (A pg. 52)
SET UP
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
75
Finalize A DVD-R/RW Disc
Finalize A Disc (DVD Deck Only)
1 Perform steps 1 to 4 of AFormat A DVD-RAM DiscB (A pg. 74)
before continuing.
2 Press FGD E to select AFINALIZEB, then press ENTER.
● For DVD-R/RW (Video mode) discs, the background selection
screen will appear. Press FGD E to select the desired
background from a selection of 18 backgrounds, then press
ENTER.
Finalizing DVD-R/RW discs recorded on this unit makes it possible
for the discs to be played back on other DVD players. DVD-RW
discs are finalized in the mode that the discs were formatted,
enabling playback on compatible DVD players.
Title names input in the Library Database Navigation are
registered as title names in the DVD menu. (A pg. 51)
3 Press D E to select AOKB, then press ENTER.
4 Upon completing finalization, ACOMPLETEDB appears on the
TV screen. Press ENTER to end.
● Turn on the unit.
5 Press SET UP to return to the normal screen.
● Menu screen is cleared.
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Load a DVD-R/RW disc to finalize.
● Once a DVD-RW (VR mode) disc has been finalized, it can be
played on DVD players compatible with VR mode.
CABLE/DBS
TV
DVD
Cancel The Finalization Of A DVD-RW Disc
1 Load a DVD-RW disc to cancel the disc finalization, and
perform steps 1 to 4 of AFormat A DVD-RAM DiscB (A pg. 74)
before continuing.
2 Press FGD E to select ACANC. FINALIZ.B, then press ENTER.
3 Press D E to select AEXECUTEB, then press ENTER.
ENTER
4 Upon completing cancellation of finalization, ACANCELLATION
COMPLETEDB appears on the TV screen. Press ENTER to
end.
FGDE
5 Press SET UP to return to the normal screen.
● When the disc finalization is canceled, the mode in which the
disc was formatted is restored, making the disc recordable.
(A pg. 9, 74)
SET UP
Before finalizing
● It is possible to record on a blank space.
● It is possible to enter title names. (A pg. 51)
● It is possible to delete titles. (A pg. 52)
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
title is deleted from a DVD-R disc.
● It is impossible to record or edit DVD-R/RW discs recorded on
other devices even if they have not been finalized.
After finalizing (For DVD-R/RW (Video mode) discs)
● Video and audio that have been recorded by then are recorded in
conformity to the DVD Video standard, enabling you to play back
the discs as DVD VIDEO discs.
● Although DVD-R/RW discs finalized on this unit become playable
on DVD players compatible with DVD-R/RW discs, some discs
still may not play, for which JVC cannot take responsibility.
● Marked points marked before finalizing will be deleted, and titles
will be divided automatically into AchaptersB approximately every
5 minutes. (A pg. 27)
● Depending on the DVD players and DVD-R/RW discs used, and
on the conditions of recording, it may not be possible to play back
the discs. In this case, play back the discs on this unit.
● Additional recordings become impossible.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
76
Scan Mode Set (HDD & DVD Deck Only)
Tray Lock (DVD Deck Only)
If you connect the unit and TV with Component Video Connection
(A pg. 18), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV
system, and Progressive scan mode which enables reproduction
of higher-quality images.
You can lock the disc tray to prohibit the unwanted disc ejection by
children.
● Turn off the unit.
8 Interlaced scan
M
o
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of
the second half of the picture in-between lines of the first half of the
picture.
8 Progressive scan
Progressive scan displays all the horizontal lines of a picture at
one time, as a single frame. This system can convert the interlaced
video from DVD into progressive format for connection to a
progressive display. It dramatically increases the vertical
resolution.
To lock tray
While the unit is turned off, press and hold o, then press M on the
unit. ALOCKB appears on the front display panel and the disc tray is
locked.
To unlock tray
ATTENTION:
Your TV needs to be compatible with Progressive.
While the unit is turned off, press and hold o, then press M on the
unit. AUNLOCKB appears on the front display panel.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Mode Lock
CABLE/DBS
TV
DVD
When the unit is turned on, press and hold ENTER on the remote
control for more than 5 seconds. ALOCKB appears on the front
display panel.
HDD
DV
DVD
● No buttons will function and playback and recording will not be
interrupted.
● When the unit is in the stop mode, all buttons will not function
except R and I.
To cancel Mode Lock, press and hold ENTER again for more than
5 seconds.
NOTE:
It is also possible to use Mode Lock during Repeat Playback
(A pg. 29).
Last Function Memory
When the power plug is disconnected from unit or when power
failure occurs, your settings for the following functions are kept in
the memory. These settings will resume when the unit is turned on
again.
● Input selection (channel or auxiliary input; L-1, F-1 or DV)
● Recorder selection (The last selected deck is memorized.)
● Country setting (A pg. 12)
PROGRESSIVE SCAN
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press PROGRESSIVE SCAN for 3 or more seconds.
● Video output indicator (q) lights on the front display panel if
Progressive scan mode has been established. (A pg. 14)
● Each press of PROGRESSIVE SCAN for 3 or more seconds
switches the scan mode.
● Recording speed (A pg. 34, 37)
● Mode settings (A pg. 70 – 72)
NOTES:
● Interlaced scan mode is the setting at your purchase.
● Interlaced scan mode might be suitable depending on video
material.
● Scan mode cannot be set while menu screen is displayed.
● When the Progressive scan mode is engaged, no video signal is
output from [S-VIDEO OUTPUT] connector and [VIDEO/AUDIO
OUTPUT] connectors.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
77
Before requesting service for a problem, use this chart and see if
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off
for repair.
Playback (DVD Deck)
The DVD deck cannot be operated.
●
The DVD deck is not selected.
] Press DV/HDD/DVD on the unit repeatedly or DVD on the
Initializing (DVD Deck Only)
remote so that the DVD lamp lights up on the unit.
Malfunction occurs on the unit.
Images do not appear on the TV screen.
] Press A to turn off the unit, press and hold A, then press o
●
The TV receiver’s channel selector is not set to the AV mode.
] Set the TV to its AV mode.
When interlace scanned program is played back, progressive
scan mode is selected.
for two seconds or more.
●
General
No power is supplied to the unit.
] Press and hold PROGRESSIVE SCAN until q disappears
from the front display panel. (A pg. 76)
●
The AC power plug is disconnected from the AC outlet.
] Connect the AC power plug to the AC outlet securely.
Playback does not start or stop immediately after playback is
started by pressing I.
(A pg. 18)
On the front display panel, ANO DISCB appears.
The remote control does not work properly.
●
The disc is loaded upside down.
] Remove the batteries, wait for 5 minutes or more, then load the
] Place the disc on the disc tray with the playback surface facing
butteries again.
down. (A pg. 10)
●
The setting of the remote control code is inappropriate.
●
A disc not being compatible with the unit is loaded.
] Load a playable disc on the unit. (A pg. 7)
A dirty disc is loaded.
] Clean the disc. (A pg. 11)
Defective disc is loaded.
] Set the same remote control code (1, 2, 3, or 4) on both the unit
and the remote control. (A pg. 67)
●
●
The batteries are discharged.
] Replace the dead batteries with new ones.
●
] Replace the warped or scratched disc with a normal one.
Dubbing from the external equipment is not possible.
Images are blurred or distorted when you start High-Speed
Search.
●
The source (another video recorder, camcorder) has not been
properly connected.
] Confirm that the source is properly connected.
All necessary power switches have not been turned on.
] Confirm that all units’ power switches are turned on.
The setting of the input channel position is inappropriate.
] Images are blurred or distorted at the point where the playback
●
speed changes and this is not a malfunction of the unit.
Playback does not start.
●
] Select the input channel position (AF-1B or AL-1B) that
corresponds to the input terminal connected to the external
equipment. (A pg. 63)
] Playback does not start for approximately 30 seconds after
recording is stopped and this is not a malfunction of the unit.
Playback does not start when you select a title or a chapter.
The on-screen display superimposed on the program played
back/received on this unit is recorded when you dub the
program to an external recording equipment.
●
The Parental Lock is engaged and the disc is rated higher than
the set level.
] Release the Parental Lock temporarily or change the set level.
] Set ASUPERIMPOSEB to AOFFB. (A pg. 72)
(A pg. 33)
The unit does not operate.
Playback (HDD Deck)
The HDD deck cannot be operated.
●
●
There are cases when the operation is prohibited on the disc.
Lightning or static electricity may cause malfunction of the unit.
] Press A to turn the power off, then press the button again to
●
The HDD deck is not selected.
turn the power on.
] Press DV/HDD/DVD on the unit repeatedly or HDD on the
remote so that the HDD lamp lights up on the unit.
The remote control of a JVC TV will not operate the unit.
●
The setting of the remote control code is inappropriate.
] To operate the unit using a JVC TV remote control, set the
remote control code of the unit to A1B (Default: A3B). (A pg. 67)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
78
Playback (DV Deck)
Recording (HDD Deck)
The DV deck cannot be operated.
TV broadcasts cannot be recorded.
●
The DV deck is not selected.
●
AL-1B or AF-1B has been selected as the input mode.
] Press DV/HDD/DVD on the unit repeatedly or DV on the remote
] Set to the desired channel.
so that the DV lamp lights up on the unit.
Camcorder recording is not possible.
The tape will not rewind or fast-forward.
●
The camcorder has not been properly connected.
] Confirm that the camcorder is properly connected.
The input mode is not correct.
●
The tape is already fully rewound or fast-forwarded.
] Check the cassette.
●
] Set the input mode to AF-1B. (A pg. 62)
The playback picture does not appear while the tape is
running.
Recording (DV Deck)
●
The TV is not set to the AV mode.
During recording, the tape does not run. The DV recording
lamp lights up on the unit.
] Set the TV to the AV mode.
Noise appears during visual search.
●
The unit is in the Record Pause mode.
●
This is normal.
] Press I to resume recording.
Recording cannot be done.
The playback picture is blurred or interrupted while TV
broadcasts are clear or AUSE CLEANING CASSETTEB
message appears on the screen.
●
There is no cassette loaded, or the cassette loaded has had its
erase protection switch set to ASAVEB.
] Insert a Mini DV cassette, or set the erase protection switch set
●
The video heads may be dirty.
to ARECB.
] Use a dry cleaning cassette M-DV12CL, or consult your JVC
dealer.
Camcorder recording is not possible.
Recording (DVD Deck)
●
The camcorder has not been properly connected.
] Confirm that the camcorder is properly connected.
The input mode is not correct.
The desired program cannot be recorded.
●
] Set the input mode to AF-1B or ADVB.
●
The channel position does not correspond to that in the
receiving area.
The tape is automatically rewound, then the unit is shut off.
] Set the correct channel position for the receiving broadcast.
●
The end of the tape was reached during recording.
(A pg. 22)
] The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
Recording cannot be made.
●
No disc or a disc not being compatible with the unit is loaded.
] Load a recordable disc on the unit. (A pg. 7)
The disc loaded is not formatted.
] Format the disc. (A pg. 74)
A finalized DVD-R disc is loaded.
Audio dubbing is not possible.
●
●
ADV AUDIO RECB had been set to A16BITB at the original
recording.
●
] Set ADV AUDIO RECB to A12BITB at the original recording.
●
] Recording cannot be made on finalized discs. Load a
The tape speed had been set to LP at the original recording.
recordable disc on the unit.
] Set the tape speed to SP at the original recording.
●
The disc is full or does not have enough space for the title to be
recorded.
Monitoring the audio dubbed sound is not possible during
audio dubbing.
] Clear unnecessary titles on the disc or load a blank disc.
(A pg. 52)
] This is normal. Monitor the sound using the connected devices.
●
The DVD-RAM disc loaded has had its protect tab slid to the
protect position.
] Release the protect tab. (A pg. 10)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
79
Timer Recording (HDD & DVD Deck)
Other Problems
Timer programming cannot be made.
The image of the TV broadcast appears distorted on the TV
screen.
●
Date and time is not correct.
] Set date and time correctly. (A pg. 21)
Timer recording is in progress.
For RF/AV/S-video connection
] Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (q) lights off on the front display panel.
●
] Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
For component video connection
] Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (q) lights up on the front display panel.
Timer programming recording does not start.
●
Date and time is not correct.
] Set date and time correctly. (A pg. 21)
Whistling or howling is heard from the TV during camcorder
recording.
VCR Plus+ Timer Programming cannot be made.
●
The camcorder’s microphone is too close to the TV.
] Position the camcorder so its microphone is away from the TV.
The TV’s volume is too high.
●
Date and time set on the unit is not correct.
] Set date and time correctly. (A pg. 21)
●
●
The channel position does not correspond to that in the
receiving area.
] Turn the TV’s volume down.
] Set the correct channel position for the receiving broadcast.
When scanning channels, some of them are skipped over.
(A pg. 22)
●
Those channels have been designated to be skipped.
The VCR Plus+ system does not timer-record properly.
] If you need the skipped channels, restore them. (A pg. 22)
●
The unit’s channel positions have been set incorrectly.
The channel cannot be changed.
] Refer to AChanging VCR Plus+ SettingB (A pg. 73) and
reperform the procedure.
●
Recording or RetroActive Recording* is in progress.
] Press W to pause recording, change the channel, then press I
On the front display panel, A– –:– –B appears.
to resume recording.
* HDD deck only
●
Power failure occurred.
] Set date and time correctly. (A pg. 21)
Channel settings that were made manually seem to have
changed or disappeared.
APROGRAM FULLB appears on the TV screen during timer
programming.
●
After the manual settings were made, Auto Channel Set was
performed.
●
16 programs have already been timer programmed.
] Perform AManual Clock SetB (A pg. 21).
] Clear unnecessary programs on the unit, then try timer
programming again. (A pg. 49)
Even though Auto or Semiauto Clock Set has been
performed, the clock is incorrect.
The disc space does not increase when recorded titles are
cleared.
●
The clock setting data received from the host channel is
incorrect.
●
The PC’s data recorded on a DVD-RAM drive cannot be
cleared on this unit.
] Format the disc. (When the disc is soiled, wipe the disc with a
] Select a different host channel during ASemiauto Clock SetB
(A pg. 21), or perform AManual Clock SetB (A pg. 21).
soft dry cloth before formatting.) (A pg. 11, 74)
Malfunction occurs and the unit cannot be power off.
] Reset the unit by disconnecting the AC power plug from the AC
outlet and connect again.
Buttons and controls do not function at all.
●
Mode Lock is activated.
] Press and hold ENTER for more than 5 seconds to cancel
Mode Lock. Or disconnect the power cord and connect again.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
80
On-screen Message (HDD & DVD Deck Only)
UNREADABLE DISC
CHECK DISC
DISC NOT REGISTERED IN THE LIBRARY
REGISTER DISC?
● When an incompatible disc is loaded, I has been pressed.
(A pg. 8)
● A disc that is not registered in the library has been inserted.
Register the disc as necessary. (A pg. 55)
COULD NOT FORMAT THE DISC
CHECK THE DISC
INSERT DISC XXXX
● Formatting is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (A pg. 11, 74)
● Appears when a title that has been selected in the library is not
contained in the loaded disc.
CAN NOT FINALIZE THIS DISC
CAN NOT RECORD OR MAKE PLAY LIST
DELETE UNWANTED TITLES
● Finalizing is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (A pg. 11, 75)
● Recording and/or editing cannot be performed.
● The number of titles exceeds 99.
CAN NOT CANCEL FINALIZATION OF THIS DISC
● The number of play lists exceeds 99.
● Canceling disc finalization is not complete since the disc may be
dirty or damaged. Take out the disc, clean it and retry. (A pg. 11,
75)
SET CLOCK BEFORE TIMER PROGRAMMING
● To set the timer program, the clock must be set in advance.
(A pg. 21)
PRESS [STOP] AGAIN TO STOP RECORDING
● During Live Memory playback, o has been pressed. (A pg. 44)
PROGRAM FULL
DELETE UNWANTED TIMER PROGRAMS
TIMER RECORDING COMPLETED
● You can program this unit to timer-record as many as 32
programs. To program more, you need to cancel a timer program
already set. (A pg. 49)
● Timer recording has finished during Live Memory playback.
PLAYBACK WILL STOP
THEN TIMER RECORDING WILL START
DISC NOT LOADED
● Timer recording finished during Live Memory playback, then the
● Operation has been attempted when a disc is not loaded, or
loaded upside down. (A pg. 10)
next timer recording is about to begin while playback continues.
COPY PROHIBITED
CAN NOT RECORD
DISC NOT RECORDABLE
INSERT RECORDABLE DISC
● An attempt has been made to record copy-protected contents.
● An attempt has been made to record copy-once contents on a
disc that is not CPRM compatible, such as DVD-R.
● When a playback-only disc or a finalized disc is loaded, R has
been pressed. (A pg. 7)
PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY
COPY PROHIBITED
CAN NOT PLAY
● An invalid PlusCode number has been input. (A pg. 46)
● The unit has detected invalid contents at the start or in the middle
of playback.
GUIDE PROGRAM IS NOT SET
SET GUIDE PROGRAM THEN RETRY
THE i.LINK DEVICE THAT YOU HAVE CONNECTED IS NOT
RECOGNIZED
MAKE SURE THAT THE DEVICE IS CONNECTED PROPERLY
AND POWERED ON
● To set the timer program using the VCR Plus+ system, the Guide
Channel Number must be set in advance. (A pg. 73)
CAN NOT SET VCR PLUS+ TIMER PROGRAMMING DURING
TIMER RECORDING OR INSTANT TIMER RECORDING
● An attempt has been made to start DV dubbing when a digital
video camera is not properly connected to the unit.
● Check the connection. (A pg. 60)
● Appears when you tried to input a PlusCode number during timer
recording or instant timer recording.
REGION CODE ERROR
CHECK DISC
● A disc loaded cannot be played back on this unit since the region
number of the disc does not match that of the unit. (A pg. 8)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
EN
81
Language Code List
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
Afar
IK
Inupiak
RN
RO
RU
RW
SA
SD
SG
SH
SI
Kirundi
Abkhazian
Afrikaans
Ameharic
Arabic
IN
Indonesian
Icelandic
Hebrew
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
IS
IW
JI
Yiddish
Assamese
Aymara
Azerbaijani
Bashkir
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
Javanese
Georgian
Kazakh
Sangho
Serbo-Croatian
Singhalese
Slovak
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Byelorussian
Bulgarian
Bihari
SK
SL
Slovenian
Samoan
Shona
SM
SN
SO
SQ
SR
SS
ST
SU
SW
TA
Bislama
Bengali, Bangla
Tibetan
BN
BO
BR
CA
CO
CS
CY
DZ
EL
EO
ET
EU
FA
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
Kirghiz
Breton
Latin
Catalan
Corsican
Czech
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Welsh
LV
Bhutani
Greek
MG
MI
TE
TG
TH
TI
Telugu
Esperanto
Estonian
Basque
Persian
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
OC
OM
OR
PA
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
TK
TL
FJ
Fiji
FO
FY
GA
GD
GL
GN
GU
HA
HI
Faroese
Frisian
Malay (MAY)
Maltese
TN
TO
TR
TS
TT
Irish
Burmese
Nauru
Turkish
Tsonga
Tatar
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Nepali
Occitan
TW
UK
UR
UZ
VI
Twi
(Afan) Oromo
Oriya
Ukrainian
Urdu
Hindi
Panjabi
Uzbek
HR
HU
HY
IA
Croatian
Hungarian
Armenian
Interlingua
Interlingue
PL
PS
PT
QU
RM
Polish
Vietnamese
Volapuk
Wolof
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
VO
WO
XH
YO
ZU
Xhosa
IE
Yoruba
Zulu
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
EN
82
Country/Area Code List for Parental Lock
AD
AE
AF
AG
AI
Andorra
CK
Cook Islands
Chile
GN
GP
GQ
GR
GS
Guinea
United Arab Emirates
Afghanistan
CL
Guadeloupe
Equatorial Guinea
Greece
CM
CN
CO
Cameroon
China
Antigua and Barbuda
Anguilla
Colombia
South Georgia and the South
Sandwich Islands
AL
Albania
CR
CU
CV
CX
CY
CZ
Costa Rica
Cuba
GT
GU
GW
GY
HK
HM
Guatemala
Guam
AM
AN
AO
AQ
AR
Armenia
Netherlands Antilles
Angola
Cape Verde
Christmas Island
Cyprus
Guinea-Bissau
Guyana
Antarctica
Argentina
Hong Kong
Czech Republic
Heard Island and McDonald
Islands
AS
AT
American Samoa
Austria
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
ER
ES
ET
FI
Germany
Djibouti
HN
HR
HT
HU
ID
Honduras
Croatia
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
Australia
Denmark
Dominica
Dominican Republic
Algeria
Haiti
Aruba
Hungary
Azerbaijan
Bosnia and Herzegovina
Barbados
Indonesia
IE
Ireland
Ecuador
IL
Israel
Bangladesh
Belgium
Estonia
IN
India
Egypt
IO
IQ
IR
British Indian Ocean Territory
Burkina Faso
Bulgaria
Western Sahara
Eritrea
Iraq
Iran (Islamic Republic of)
Bahrain
Spain
IS
Iceland
Italy
Burundi
Ethiopia
IT
BJ
Benin
Finland
JM
JO
JP
KE
Jamaica
Jordan
Japan
Kenya
BM
BN
BO
Bermuda
FJ
Fiji
Brunei Darussalam
Bolivia
FK
FM
Falkland Islands (Malvinas)
Micronesia
(Federated States of)
BR
BS
BT
BV
BW
BY
Brazil
FO
FR
FX
GA
GB
GD
Faroe Islands
France
KG
KH
KI
Kyrgyzstan
Cambodia
Bahamas
Bhutan
France, Metropolitan
Gabon
Kiribati
Bouvet Island
Botswana
Belarus
KM
KN
KP
Comoros
United Kingdom
Grenada
Saint Kitts and Nevis
Korea, Democratic People’s
Republic of
BZ
CA
CC
CF
CG
Belize
GE
GF
GH
GI
Georgia
KR
KW
KY
KZ
LA
Korea, Republic of
Kuwait
Canada
French Guiana
Ghana
Cocos (Keeling) Islands
Central African Republic
Congo
Cayman Islands
Kazakhstan
Gibraltar
GL
Greenland
Lao People’s Democratic
Republic
CH
CI
Switzerland
Côte d’Ivoire
GM
Gambia
LB
Lebanon
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
EN
83
LC
LI
Saint Lucia
Liechtenstein
Sri Lanka
NU
NZ
OM
PA
Niue
SZ
TC
TD
TF
TG
TH
TJ
Swaziland
New Zealand
Oman
Turks and Caicos Islands
Chad
LK
LR
LS
Liberia
Panama
French Southern Territories
Togo
Lesotho
PE
PF
PG
PH
PK
PL
Peru
LT
Lithuania
French Polynesia
Papua New Guinea
Philippines
Pakistan
Thailand
LU
LV
Luxembourg
Latvia
Tajikistan
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UM
Tokelau
LY
Libyan Arab Jamahiriya
Morocco
Turkmenistan
Tunisia
MA
MC
MD
MG
MH
ML
MM
MN
MO
MP
MQ
Poland
Monaco
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
Saint Pierre and Miquelon
Pitcairn
Tonga
Moldova, Republic of
Madagascar
Marshall Islands
Mali
East Timor
Turkey
Puerto Rico
Portugal
Trinidad and Tobago
Tuvalu
Palau
Myanmar
Paraguay
Taiwan
Mongolia
Qatar
Tanzania, United Republic of
Ukraine
Macau
Réunion
Northern Mariana Islands
Martinique
Romania
Uganda
Russian Federation
United States Minor Outlying
Islands
MR
MS
MT
MU
MV
Mauritania
Montserrat
Malta
RW
SA
SB
SC
SD
Rwanda
US
UY
UZ
VA
VC
United States
Saudi Arabia
Solomon Islands
Seychelles
Sudan
Uruguay
Uzbekistan
Mauritius
Maldives
Vatican City State (Holy See)
Saint Vincent and the
Grenadines
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
Malawi
SE
SG
SH
SI
Sweden
VE
VG
VI
Venezuela
Mexico
Singapore
Virgin Islands (British)
Virgin Islands (U.S.)
Viet Nam
Malaysia
Mozambique
Namibia
Saint Helena
Slovenia
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
SJ
Svalbard and Jan Mayen
Slovakia
Vanuatu
New Caledonia
Niger
SK
SL
SM
SN
SO
SR
ST
SV
SY
Wallis and Futuna Islands
Samoa
Sierra Leone
San Marino
Norfolk Island
Nigeria
Yemen
Senegal
Mayotte
Nicaragua
Netherlands
Norway
Somalia
Yugoslavia
South Africa
Zambia
NL
Suriname
NO
NP
NR
Sao Tome and Principe
El Salvador
Nepal
Zaire
Nauru
Syrian Arab Republic
Zimbabwe
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C INTERFACE
84
EN
RS-232C Interface – Command Table –
Lower OrderN
Higher OrderQ
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Cassette
Out
ACK
NAK
0
1
2
3
4
5
6
7
8
9
A
PLAY
STOP
STILL
Standby
ON
Standby
OFF
Eject
FF
REW
Fwd Shtl
Rev Shtl
DateData
Sense
ClockData
Sense
B
C
D
Rec
Rec
Pause
Status
Sense
Tc Data
Sense
CTL
Data
JVCStatus
Sense
Sense
E
F
Command
Target
Rec/Dub
Request
Vtr Ind
RS-232C Interface – Specifications –
● 9PIN D-Sub
Mode
: Non-synchronous
1
6
5
9
Character length
Parity check
Start bit
: 8 bits
: None
: 1
Stop bit
Data rate
: 1
: 9600bps
Bit configuration
PIN No.
Signal
Operation
Direction of
signal
2
3
5
RxD
TxD
Receive data
Transmit data
HDD/DVDOPC
HDD/DVDNPC
D0 D1 D2 D3 D4 D5 D6 D7
Stopping bit
Starting bit
GND
Signal grounding
NOTES:
● When using the Serial Command Connector, the cable to be used should be a RS-232C interface cable (straight type).
● It takes about 10 seconds for the communication to be established after turning on the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C INTERFACE
EN
85
● System Commands
Commands relating to RS-232C control system.
RS-232C Interface – Command –
● Operation Commands
Command
Description
Commands for operating functions such as PLAY and REC on the
HDD/DVD/Mini DV deck.
0A
ACK: A return command issued when a defined
command is received.
Command
Description
Plays the selected deck.
0B
FB
NAK: A return command issued when an
undefined or possibly nonexistent command is
received.
3A
3F
Stops the selected deck. Resume will be cleared
when this is pressed while in the Stop mode.
(HDD/DVD Deck)
VTR Ind: A command for checking whether the
connected device is a VTR.
Rec Request will be cleared.
● Response Commands
4F
AO
A1
A3
Switches the selected deck to the Still mode.
Commands for acquiring information such as deck status.
Power On
Power Off
Command
Description
03
Cassette Out: Issued by the Mini DV deck when
the cassette is ejected after ejecting is performed.
Eject: HDD/DVD Deck: Opens/Closes tray.
Mini DV Deck: Removes cassette.
BE
BF
D7
D8
Date Sense: For acquiring the currently
configured year, month and day.*
AB
AC
B5
B6
FF: HDD/DVD Deck: Functions only during
playback. Activates forward search. Forward
search speed increases in step of 2x, 4x, 8x and
16x via each operation.
Mini DV Deck: Fast forward. Search Fwd during
playback.
Time Sense: For acquiring the currently
configured hour, minute and second.*
Status Sense: For acquiring the deck
information.*
REW: HDD/DVD Deck: Functions only during
playback. Activates reverse search. Reverse
search speed increases in step of 2x, 4x, 8x and
16x via each operation.
Mini DV Deck: Rewind. Search Rev during
playback.
TC Data Sense: For acquiring the total remaining
time in the current recording mode when there is
a media in the selected deck.*
D9
CTL Data Sense: For acquiring the lapse counter
when there is a media in the selected deck.*
Fwd Shtl: HDD/DVD Deck: Functions only during
playback. Activates forward search. Forward
search speed increases in step of 2x, 4x, 8x and
16x via each operation.
Mini DV Deck: Fast forward. Search Fwd during
playback.
DD
JVC Data Sense: Returns data from the unit.*
* See pages 86 and 87 for data format.
Rev Shtl: HDD/DVD Deck: Functions only during
playback. Activates reverse search. Reverse
search speed increases in step of 2x, 4x, 8x and
16x via each operation.
Mini DV Deck: Rewind. Search Rev during
playback.
CA
CB
Rec: Starts recording at the selected deck when
a Rec Request is received.
Rec Pause: Switches the selected deck to the
Rec Pause mode when a Rec Request is
received.
F0
FA
Command Target: VTR1: For selecting Mini DV
deck.
HDD1: For selecting HDD deck.
DVD1: For selecting DVD deck.
Rec Request: For issuing approval for recording.
This can be cleared using STOP.
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C INTERFACE
EN
86
Date Data Sense
For acquiring the currently configured year, month and day in ASCII codes.
1st Byte
Yr (Tens)
3*
2nd Byte
Yr (Ones)
3*
3rd Byte
Mth (Tens)
3*
4th Byte
Mth (Ones)
3*
5th Byte
Day (Tens)
3*
6th Byte
Day (Ones)
3*
Date Sense
BE
E.g. (2004.11.17)
30
34
31
31
31
37
When the current time is not set, the value is fixed as “—” (0x2D).
Time Data Sense
For acquiring the currently configured hour, minute and second in ASCII codes.
1st Byte
Hr (Tens)
3*
2nd Byte
Hr (Ones)
3*
3rd Byte
Min (Tens)
3*
4th Byte
Min (Ones)
3*
5th Byte
Sec (Tens)
3*
6th Byte
Sec (Ones)
3*
Time Sense
BF
E.g. (12:34:56)
31
32
33
34
35
36
When the current time is not set, the value is fixed as “—” (0x2D).
Status Data Sense
D7 STATUS SENSE
1byte
2byte
3byte
HDD/DVD
DV
1 (Fixed)
HDD/DVD
1 (Fixed)
DV
HDD/DVD
DV
bit7
bit6
Video EE
Audio EE
Video EE
Audio EE
0 (Fixed) 0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed) Timer REC
(Including
PAUSE)
bit5
bit4
0 (Fixed)
0 (Fixed)
Video Mute
Audio Mute
Video Mute
Audio Mute
0 (Fixed) 0 (Fixed)
0 (Fixed) 0 (Fixed)
Record
Forbidden
Record
Forbidden
bit3
bit2
Cassette Not
Inserted
Cassette Not
Inserted
Occurrence of
abnormality in VTR
Occurrence of
abnormality in VTR
0 (Fixed) 0 (Fixed)
0 (Fixed)
0 (Fixed)
Occurrence of moisture Occurrence of moisture
condensation in VTR condensation in VTR
0 (Fixed) During Repeat
Playback (Including
PAUSE)
bit1
bit0
0 (Fixed)
0 (Fixed)
0 (Fixed) 0 (Fixed)
0 (Fixed) 0 (Fixed)
Occurrence of
DV EMG
Occurrence of
EMG
D7 STATUS SENSE
4byte
5byte
DV
HDD/DVD
DV
HDD/DVD
bit7
During PLAY
During PLAY
During PAUSE (Set to 1 simultaneously During PAUSE (Set to 1 simultaneously
with During PLAY in STILL mode, set with During PLAY in STILL mode, set
A
B
A
B
to 1 simultaneously with
in REC PAUSE mode.)
A
During REC
B
to 1 simultaneously with
in REC PAUSE mode.)
ADuring RECB
bit6
bit5
During FF
During FF
0 (Fixed)
0 (Fixed)
0 (Fixed)
During REW
During REW
During Reverse Shuttle Search
(Excluding STILL)
bit4
bit3
bit2
During STOP
During STOP
During Forward Shuttle Search
(Excluding STILL)
0 (Fixed)
0 (Fixed)
0 (Fixed)
During STANDBY
(Unit Power Off)
During STANDBY SPEED CODE 3
(Unit Power Off)
During CASSETTE 0 (Fixed)
EJECT
SPEED CODE 2
bit1
bit0
During REC
During REC
SPEED CODE 1
0 (Fixed)
0 (Fixed)
During Audio Dub
During Audio Dub SPEED CODE 0
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C INTERFACE
EN
87
TC Data Sense
TC Data Sense
For acquiring the remaining time in the current recording mode in hours, minutes and seconds for HDD/DVD,
and hours and minutes for Mini DV.
1st Byte
2nd Byte
3rd Byte
4th Byte
5th Byte
6th Byte
7th Byte
8th Byte
Hr (Tens)
Hr (Ones)
Min (Tens)
Min (Ones)
Sec (Tens)
Sec (Ones)
Frame
(Tens)
Frame
(Ones)
D8
3*
3*
3
3*
3*
3*
3*
3*
3*
E.g. (01:23:45)
30
32
33
34
35
30
30
E.g.: When remaining time is 1 hr 23 min 45 sec.
Mini DV (hr and min only)
HDD/DVD (hr, min and sec only)
Frame is fixed as 0.
CTL Data Sense
CTL Data Sense
For acquiring lapse counter of selected deck in hours, minutes and seconds.
1st Byte
2nd Byte
3rd Byte
4th Byte
5th Byte
6th Byte
7th Byte
8th Byte
Hr (Tens)
Hr (Ones)
Min (Tens)
Min (Ones)
Sec (Tens)
Sec (Ones)
Frame
(Tens)
Frame
(Ones)
D9
3*
3*
3*
3*
3*
3*
3*
3*
Eg. (01:23:45)
30
31
32
33
34
35
30
30
E.g.: When time lapse counter is 1 hr 23 min 45 sec.
JVC Data Sense
DD JVC
1byte
2byte
3byte
4byte
SENSE
DV
1 (Fixed)
0 (Fixed)
0 (Fixed)
During
HDD/DVD
1 (Fixed)
0 (Fixed)
0 (Fixed)
DV
HDD/DVD
DV
HDD/DVD
DV
HDD/DVD
1 (Fixed)
1 (Fixed)
0 (Fixed)
bit7
bit6
bit5
0 (Fixed)
0 (Fixed)
1 (Fixed)
0 (Fixed)
0 (Fixed)
1 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
1 (Fixed)
1 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
bit4
bit3
bit2
Playback of LP 0 (Fixed)
Recorded Tape
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
During Audio
Dub (Including
PAUSE)
0 (Fixed)
0 (Fixed)
During Insert
(Including
PAUSE)
bit1
bit0
1 (Fixed)
1 (Fixed)
1 (Fixed)
1 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
During REC
(Including Timer
REC, Normal REC,
OTR, RECLINK
REC, DV AUTO
REC and also REC
PAUSE.)
During REC
(Including
PAUSE)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
88
EN
GENERAL
VIDEO/AUDIO (HDD Deck)
Power requirement
AC 120 VH, 60 Hz
Video recording compression system
MPEG2 (VBR)
Power consumption
Power on: 49 W
Power off: 15 W
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Temperature
Operating: 5°C to 35°C (41°F to 95°F)
Storage: –20°C to 60°C (–4°F to 140°F)
Recording time
Maximum 300 hours (with 160 GB HDD)
(XP): Approx. 34 hours
(SP): Approx. 69 hours
(LP): Approx. 138 hours
(EP): Approx. 209 hours
(FR): Approx. 300 hours
Operating position
Horizontal only
Dimensions (WxHxD)
435 mm x 96 mm x 372 mm (17-1/10" x 3-4/5" x 14-3/5")
Weight
6.2 kg (13.7 lbs)
VIDEO/AUDIO (DV Deck)
Signal system
Input/Output
NTSC color signal and EIA monochrome signal, 525 lines/60 fields
Video input: 0.5 – 2.0 Vp-p, 75 K (pin jack)
Video output: 1 Vp-p, 75 K (BNC)
Audio input:
Recording system
Digital Component Recording
–8 dB, 50 kK (pin jack)
Format
DV format (SD mode)
Corresponding to mono (left)
Audio output: –8 dB, 1 kK (pin jack)
S-video input:
Cassette
Mini DV Cassette
Y: 0.8 – 1.2 Vp-p, 75 K
C: 0.2 – 0.4 Vp-p, 75 K
S-video output:
Y: 1.0 Vp-p, 75 K
C: 0.3 Vp-p, 75 K
DV: 4-pin for DV IN/OUT
Component video output:
Y: 1.0 Vp-p, 75 K
Maximum recording time
(SP): 80 min. with M-DV80ME cassette
(LP): 120 min. with M-DV80ME cassette
Audio recording system
PCM 48 kHz, 16 bit (2 ch)/
32 kHz, 12 bit (4 ch)
CB/CR, PB/PR: 0.7 Vp-p, 75 K
Corresponding to copy protection
Remote Input: R3.5 mm Jack
Serial Command: D-SUB 9-PIN
Digital audio output:
Specifications shown are for SP mode unless otherwise specified.
TUNER/TIMER
Optical, Coaxial
Corresponding to Dolby Digital and DTS Digital Surround
Bit stream
Tuning system
Frequency synthesized tuner
Channel coverage
Selectable in digital audio output setting menu
VHF: Channels 2 - 13
UHF: Channels 14 - 69
CATV: 113 channels
VIDEO/AUDIO (DVD Deck)
Recording time
Maximum 8 hours (with 4.7 GB disc)
(XP): Approx. 1 hour
Memory backup time
Approx. 60 minutes
(SP): Approx. 2 hours
(LP): Approx. 4 hours
ACCESSORIES
Provided accessories
RF cable,
(EP): Approx. 6 hours
(FR): Approx. 1 hour – 8 hours
Audio/Video cable,
Infrared remote control unit,
AAAB battery x 2
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Video recording compression system
MPEG2 (CBR/VBR)
E.& O.E. Design and specifications subject to change without
notice.
ATTENTION:
This unit contains microcomputers. External electronic noise or
interference could cause malfunctioning. In such cases, switch
the unit off and unplug the AC power cord. Then plug it in again
and turn the unit on. Take out the disc. After checking the disc,
operate the unit as usual.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIST OF TERMS
EN
89
A
O
A-B Repeat Playback ................................................ 30
Accidental erasure prevention .................................... 41
Adjusting The Picture Quality ..................................... 31
Angle Selection ........................................................ 27
Audio Channel Selection ........................................... 28
Audio Language/Sound Selection ............................... 28
Auto Channel Set ..................................................... 22
Auto Daylight Saving Time ........................................ 21
P
Pan&Scan ................................................................ 23
Play List ................................................................... 53
Progressive scan ...................................................... 76
C
R
Cancel And Change Programs ................................... 49
Check Programs ....................................................... 49
Country/Area Code List for Parental Lock .................... 82
Region Number .......................................................... 8
Register Disc ............................................................ 55
Relief Recording ....................................................... 48
Repeat Playback ...................................................... 29
RetroActive Recording .............................................. 45
D
Disc menu ............................................................... 25
Disc Remaining Time ...........................................35, 38
Disc Resume ........................................................... 71
Discs For Playback Only ............................................. 8
DVD menu ............................................................... 25
E
Elapsed Recording Time Indication .......................35, 38
S
F
Skip Search ..................................................26, 39, 42
Soundtrack Selection ................................................ 42
Still Picture/Frame-By-Frame Playback ............25, 39, 42
File Structure Of Discs ................................................ 9
G
Guide Channel Number ............................................. 73
I
Instant Replay ......................................... 28, 40, 42, 45
Instant Timer Recording (ITR) ...............................35, 38
Interlaced scan ......................................................... 76
J
T
Jump Search .......................................................26, 40
Time Code ............................................................... 42
Time Search ............................................................ 31
L
Language Code List .................................................. 81
Last Function Memory ............................................... 76
Letter Box ................................................................ 23
Live Memory ............................................................ 45
M
Manual Channel Set ................................................. 22
Manual Clock Set ..................................................... 21
Marking Positions To Play Back Again Later ...........27, 40
Menu/Audio/Subtitle Language Set ............................. 20
Mode Lock ............................................................... 76
V
W
Weekly/Daily Recording ............................................ 47
N
Next Function Memory .............................................. 42
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
EN
90
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
EN
91
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Printed in China
0405CSH-SW-BJ
US
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2005 Victor Company of Japan, Limited
|