SIROCCO VENTILATION HOOD
OWNER’S GUIDE
READ AND SAVE THESE INSTRUCTIONS
Models: B81200 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
FORRESIDENTIALUSEONLY
NOT TO BE INSTALLED OVER GAS GRILLS
Installation
PLEASEREADENTIREINSTRUCTIONSBEFOREPROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER:Pleaseretaintheseinstructionsforfuturereference.
SAFETY WARNING: Turn off power circuit at the service entrance and lock out panel, before wiring this appliance.
REQUIREMENT: 120 V AC, 60 Hz. 15 or 20 Amp
Before Installing Hood
Dimensions
1. This hood is designed to be mounted flush to the rear wall (to
Cabinet Front View
avoid clearance from wall to hood) and to the internal sides of
cabinet (where hood must be fixed); for this reason we
suggest installing this hood only inside a cabinet having an
internalwidthof221/16”forthe24”Model,287/16”forthe30”Model,347/16”forthe
9
15
/
"
16
36”Modelandwithaninternaldepthofminimum71/2”.Seefigure1.
The external depth of the cabinet must be minimum 10 13/16” and
maximum 13 3/16”. See figure 1.
Fixing
Point 1
Fixing
Point 1
Fixing
Point 2
Fixing
Point 2
Attention! Do not consider the door of the cabinet when
measuring.
The appliance is also supplied with 4 spacers that can be
snapped at fixing point 1 and 2 , cabinets /4” wider can be
24” - 30” - 36”
1
used, see figure 2.
2. For the most efficient air flow exhaust, use a straight run or as few
elbows as possible.
Cabinet Top View
Internal Width
1
22
28
34
/
/
/
" (24" Model)**
16
" (30" Model)**
16
" (36" Model)**
16
7
7
CAUTION: Vent unit to outside of building ONLY.
3
1
/
"
4
3. Ifallowedinyourarea,usemetallicflexductingonlytoconnectrigid
duct directly to transitions.
Rearside of the Cabinet/Hood
13
2
/ "
16
3
4. COLDWEATHERinstallationsshouldhaveanadditionalbackdraft
damperinstalledtominimizebackwardcoldairflowandanonmetallic
thermal break to minimize conduction of outside temperatures as
part of the ductwork. The damper should be on the cold air side of
the thermal break. The break should be as close as possible to
where the ducting enters the heated portion of the house.
Anon-returnsmokedamperissuppliedmountedonthetransition.
5. Hood installation height above cooktop is at the users preference.
The lower the hood above the cooktop, the more efficient the
capturingofcookingodors,greaseandsmoke.Werecommendthat
the hood be installed 18” to 36” over an electric cooktop and 25” to
36” over a gas cooktop . Be sure that your hood model fits your
installation.
max 13
min 10
/
" *
16
/
13
" *
16
Cut-Out for
5" Duct
C
Cabinet
Door
7
L
3
/ "
16
Cut-Out for
1/2" Conduit
* Do not consider the door of the cabinet
** Use spacers for 1/4" wider cabinet
Cabinet Right/Left Side View
min Depth of
Recessed
1
Area =
7
/
"
2
Cabinet
Door
min Height
of Recessed
3
Fixing
Basic Installation Steps
Foreasiestinstallation,thehoodshouldbeinstalledinthecabinet
beforemountingthecabinettothewall.Inanycasetheinstallation
stepsdonotchange.
Point 1
Area = 15
/
"
16
6"
Fixing
Point 2
3
1
3
/
"
8
5
/
16
"
1
4
/ "
16
11
/
16
"
Tools required for installation
Screw driver (philips # 1 )
Electric drill
13
13
/
"
10
/ "
16
16
11
17
/
"
16
Figure 1
5
7
with twist bit /64” and /32” or 15/64”
Tape
Pin Housing
This Hood can easily be installed following these basic steps:
• Prepare the cabinet (cut out bottom and top of the cabinet as
required and mark fixing points)
• Run conduit and duct sections to the hood and make connections
• Fix the hood to the cabinet
Motor Housing
Fixing Points 1-2
Spacer Pin
Spacer
for 1/4”
wider
Snap Spacer
Pins Into Their
Housings
cabinet
• Mount the cabinet on the wall
• Connectducttotheoutsideandconduit section totheservicepanel
Figure 2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Prepare the cabinet for installation
1
7
7
22
28
34
/
16
/
16
/
16
" (24" Model)**
" (30" Model)**
" (36" Model)**
• Mark and cut-out the cabinet bottom as shown in figure 3.
• Fit the template, which comes with the hood, on the inner
right side of the cabinet making sure the side with arrows
matcheswiththeloweredgeofthecabinetandtherearedge
of the cabinet or cut-out.
Rearside of the Cabinet***
3
max 13
min 10
/
" *
1
16
/
7
/ "
2
CUT-OUT
13
" *
16
Cabinet
Door
C
L
* Do not consider the Door of the Cabinet
4
** Add
/
"
16
when using Spacers
*** Rearside of the Cut-Out for cabinet deeper
3
than 13
/
" (without considering the door)
16
Figure 3
• Drill 2holes5/64”(seefigure4-fixingpoint1and2)and1blind
Cabinet
Door
13
hole 15/64” in diameter, /64” in depth.
• Move template to the other side and repeat.
• Make cut-out for duct and conduit, see figure 1.
Fixing
point 1-2
Fixing
point 1-2
Template
Template
cutout for
1/2" Conduit
and 5" Duct
Bottom of
the cabinet
Backside
border
Backside of
the cabinet
Blind hole
(Side Springs
Housing)
Figure 4
Prepare the hood for installation
• Remove the hood from packaging, check its condition and
make sure the following pieces are included:
1 hood,
1 registration card
1 instruction manual
1 template
1 transition with damper
1 plastic bag with 4 hood fixing screws + 1 transition fixing
screw and 4 spacers.
• Remove the light shield, unscrew and remove lamps to
prevent damage when installing (see paragraph on “Light
replacement”fordetails).
Figure 5
• Pulloutthesliderandremovethegreasefilters(seeparagraph
“Toremovethegreasefilters”fordetails).
• Fit the transition on the outlet hole of the hood:
This has a bayonet lock and must be fixed to the hood with
one screw (Figure 5), check the opening and closing of the
dampermountedinside.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Install the Hood
• Set the motor housing into the opening.
• Pushthespringinsidethemotorhousingusingascrewdriver
as a lever from the inside of the motor housing.
• Insertitcompletelyinplacetakingcaretosnapsidessprings
intotheblindholesmadefortemporaryfixingandthatconduit
and duct section, if already fitted, run freely across the cut-
outs on top of the cabinet, see figure 6.
Cabinet
• Fixthehoodpermanentlywithtwoscrews(4.5x16)perside
tobeinsertedfrometheinsideofthehoodtothecorresponding
sidefixingpoints1and2drilledonthecabinet, seefigure7.
• Connect a 5” duct to the transition and seal with tape.
• Connect to power supply
Side Spring
Attention! While mounting the hood on the wall cabinet be
sure once the hood has been fastened, that the wiring
compartment is easily and safely accessible, in order to
make safety inspections and/or maintenance operations.
WARNING!
ELECTRICALGROUNDINGINSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL
JUNCTION BOX WITH 3 WIRES, ONE OF WHICH
(GREEN/YELLOW) SERVES TO GROUND THE
APPLIANCE. TOPROTECTYOUAGAINSTELECTRIC
SHOCK, THE GREEN/YELLOW WIRE MUST BE
CONNECTED TO THE GROUNDING WIRE IN YOUR
HOME ELECTRICAL SYSTEM, AND IT MUST UNDER
NOCIRCUMSTANCESBECUTORREMOVED.
ing
Side Spr
Figure 6
Warning:Turnoffpowercircuitattheservicepanelbeforewiring
this unit.
Cabinet
Door
120 VAC, 15 or 20 Amp circuit required.
a. Remove j-box cover as shown in Figure 8.
Fixing
point 1-2
b. Removetheknockoutandinstallthestrainrelief(conduit)
Fixing
point 1-2
connector (1/2") in junction box.
Template
Template
cutout for
1/2" Conduit
and 5" Duct
c. Run 3 wires; black, white and green (#16 AWG) in 1/2"
conduit from service panel to junction box.
Bottom of
the cabinet
Backside
border
d. Connect black wire from service panel to black or red in
junctionbox,whitetowhiteandgreentogreen-yellow.See
Figure8.
Backside of
the cabinet
Blind hole
(Side Springs
Housing)
Figure 7
e. Close junction box cover.
Conduit
Figure 8
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Box adjustment
M
Thehoodcanbeinstalledincabinetswithdifferentdepths(see
alsofigure1fordetails);howeverthefrontofthesliderboxmust
always be flush with the front of the cabinet.
For alignment, adjust the back stops of the box.
For box adjustment, loosen screws M, slide the square plates
P as necessary, and tighten screws M (Figure 8).
Ensure that the drawer, when fully retracted, turns OFF all
P
power by acting positively on the rear microswitch.
Figure 8
Final installation steps
• Insert lamps in place.
• Fit the Lamp Shield.
• Fit the Grease Filters.
• Check all light bulbs to make sure they are secure in their
sockets,thenturnpoweroninservicepanelandchecklights
andbloweroperationperUse&Caresectionofthismanual
and install filters.
• Make sure to leave this manual for the home owner.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
READTHEINSTRUCTIONSCAREFULLYBEFOREUSINGTHERANGEHOOD.
For satisfactory use of your hood, become familiar with the various functions
of the hood as described below
Use and Care
Control Pad Functions
Air outlet
Motor
Housing
Light OFF
Light ON
0
1
2
3
4
0
1
Slider
Box
Very High Speed
Right Grease
Filter
Handles
High Speed
Medium Speed
Low Speed
Blower OFF
Left Grease Filter
Handles
Grease
Filters
Lamp Shield
Figure 7
Operating Instructions
The blower should be turned on for about 5 minutes before cooking in order to establish air currents upward through
the hood.
Use the low speeds for normal use and the higher speeds for strong odors or fumes.
Minimize cross drafts which will reduce the effectiveness of the hood.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HoodCleaning
Be sure lights are cool before cleaning the hood.
To Clean Filters
• The metal grease filters will last forever.
They are made of anodized aluminum
• It is recommended that the filters be washed at least once a month; they
can be washed by hand or in the dishwasher.
• Drain water through edge holes and let each filter dry thoroughly before
replacing it.
To Remove The Metal Grease Filters
• Turn blower and lights off.
• Pushsimultaneouslythetwogreasefilterhandlesfirstupwards,then pulltowards
the center and extract the filters Figure 8.
Figure 8
• Toreinstall,reverseprocedure.
To Clean Hood Surface
• For general care, wipe the outside of the white or black hood with sudsy water
orgeneralkitchenhouseholdcleaners, rinsewellanddrywithcleansoftclothto
avoidwatermarks.
• Do not use abrasive products.
Lights replacement
R
Q
NOTE: Turn blower and lights off. Make sure the lights are cool. If new lights
G
do not operate be sure lights are inserted correctly before calling service.
• Remove the light shield Q by pushing simultaneously the two unlocking buttons
R (Figure 9); for safety reasons make sure to remove the light shield from its
suspension slides G.
Attention: When removing, handle the light shield by the glass.
• Pull out fluorescent tube and replace with Philips Type PL-S 9 Watt maximum.
• Refit the light shield.
Figure 9
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LI1QVB Ed. 05/02
Download from Www.Somanuals.com. All Manuals Search And Download.
|