JVC Projection Television HD 52G887 User Manual

Projection Television Users Guide

For Models:

HD-52G787

HD-56G787

HD-61G787

HD-52G887

HD-56G887

HD-61G887

HD-70G887

Illustration of HD-52G887 and RM-C18G

Important Note:

In the spaces below, enter the model and serial number of your television (located

at the rear of the television cabinet). Staple your sales receipt or invoice to the

inside cover of this guide. Keep this user’s guide in a convenient place for future

reference. Keep the carton and original packaging for future use.

Model Number:

LCT2063-001C-A

0806TNH-II-IM

Serial Number:

Download from Www.Somanuals.com. All Manuals Search And Download.

• As an “ENERGY STAR ” partner,

JVC has determined that this

product or product model meets the

“ENERGY STAR ” guidelines for energy

efficiency.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to

avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such

as vases, shall be placed on the apparatus.

Download from Www.Somanuals.com. All Manuals Search And Download.

16) Avoid improper installation and never position the unit where good ventilation is impossible. When

installing this TV, distance recommendations must be maintained between the set and the wall,

as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance

guidelines shown for safe operation.

200 mm

150 mm

50 mm

INPUT

OPERATE

CHANNEL

–

INPUT-4

VIDEO

L/MONO

VOLUME

LAMP

POWER

AUDIO

17) Cautions for installation

— Do not tilt the TV towards the left or right, or towards the back.

— Install the TV in a corner on the floor so as to keep cords out of the way.

— The TV will generate a slight amount of heat during operation. Ensure that sufficient space is

available around the TV to allow satisfactory cooling.

18) Make enough room for inserting and removing the power plug. Place the TV as close to the

outlet as possible. The main power supply for this TV is controlled by inserting or removing the

power plug.

FCC Notice:

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

CAUTION - These television models, HD-56G647, HD-56G657, HD-56G787, HD-56G887,

HD-61G567, HD-61G587, HD-61G647, HD-61G657, HD-61G787 and HD-61G887 are for

use only with JVC Model RK-CPRM7 stand. Use with other stands is capable of resulting in

instability causing possible injury.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings

We have an important note for customers who subscribe to basic cable services (do not have

a separate cable box) and plan to use their JVC TV remote control to select channels.

Once you run the Auto Tuner Setup (which detects and programs all the channels your TV is

receiving through the RF input), every channel number available from your cable company

will appear in your television’s Channel Summary and they will all be marked as available for

scanning. Even though every channel is detected and appears as available, you will only be

able to view those that you speciﬁcally subscribe to from your cable company. This will likely

mean there are blank channels between those channels you wish to scan or “surf”.

We apologize for any inconvenience this may cause but it is important to note that this is

not a malfunction of your television. If you want to sequentially scan those channels you

subscribe to without blank ones in between, you can contact your cable company for their

cable box and remote.

Caring for the Cabinet

Normally, light dusting with a soft, non-scratching duster will keep your TV clean.

If you wish to wipe down the television, first unplug it. Then wipe gently with a soft cloth, slightly

moistened with water. You can add a few drops of mild liquid detergent to the water to help

remove spots of oily dirt.

• DO NOT allow liquid to enter the TV through the ventilation slots.

• DO NOT use strong or abrasive cleaners on the TV.

• DO NOT spray liquids or cleaners directly on the TV’s surface.

• DO NOT rub or scrub the TV harshly. Wipe the set gently with a soft cloth.

Caring for the Screen

The screen is treated with an electrostatic-proof coating. When it gets dirty, wipe it gently with a

soft cloth. If the screen is very dirty, wipe it down with a cloth dipped in a diluted kitchen cleaner

and thoroughly wrung-out. Then wipe immediately after with a clean, dry cloth.

Do not apply alcohol, organic solvents (like acetone), acidic or alkaline cleansers to the screen.

These will remove the coating layer and cause discolorations.

Do not push or hit the screen. This could cause scratches on the screen surface and image

distortions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings

Thank you for purchasing a JVC HDTV-ready projection television which uses the high-quality

HD-ILA projection system. This is one of the highest quality and most technologically advanced

televisions available today. It is recommended that you read this instruction manual before using

your television in order to learn about it’s many features. Cautions related to the safe use of the

device and important information which will help you to be able to use this device for a long time

is in the Appendix. Once again, thank you for purchasing this television and please enjoy using

it.

In order to use the television for a long time

This television uses a lamp to project the picture onto the screen. Before using this television,

please read the safety cautions and information about this television which are summarized

below.

1. When the power is turned on, the warming up commences

This television uses a lamp to project the picture onto the screen. Once the lamp has warmed

up, you can enjoy the pictures at their full brightness. What happens when the power is turned

on is explained below. Immediately after the power is turned on, since the lamp has not had

time to warm up, the picture is displayed only dimly on the screen. As the lamp warms up, the

picture becomes brighter. It takes approximately one minute for the lamp to warm up to it’s

normal operating temperature. There are 2 LED indicators on the front panel of the television

that can be used as a guide. When the POWER button is pressed, the LAMP LED indicator

blinks in orange for approximately 1 minute at approximately every 2 seconds, and then goes

out.

Note: It is impossible to turn the power off during this period. After 1 or more minutes have

passed, you can turn off the power.

2. Cooling the inside of the television and the lamp

Cooling is also performed while the television is being shut down.

When the POWER button is pressed to turn off the power, the following operations are

performed. When the television is turned off, the picture on the screen disappears. Once the

screen is dark, cooling is performed for approximately 90 seconds. When the cooling is being

performed, the LAMP LED indicator on the front panel blinks in orange at approximately every

3 seconds. The television can not be operated while the cooling is being performed.

After the cooling has been performed for 90 seconds, the power is turned off. Do not remove

the electrical plug until after the cooling process has completed. If the electrical plug is

removed before the cooling process has completed, the internal circuits and lamp may overheat

leading to the life of the lamp being shortened and the possibility of malfunctions.

Do not block the ventilation holes.

Do not block the ventilation holes while the power is turned on. Do not block the air intake holes

behind the speaker grills.

3. The lamp is a consumable item

Replace the lamp when it has blown or when the picture becomes dark. The lamp is a user

replaceable item. The lamp must be recycled. For a detailed explanation on how to recycle the

lamp, refer to the Appendix and the instructions that are included with the replacement lamp kit.

The life of the lamp changes depending on the atmospheric temperature and altitude in which

the TV is being used.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings

4. The television requires a lot of electrical power

It is recommended that the television is connected directly to the wall socket, and not to another

device. When connecting the television to a wall socket that is being used by another device, or

when using an extension cord, be careful not to exceed the electrical capacity of the socket.

Do not turn the power on and off repeatedly in a short amount of time.

It subjects the television and the lamp to stress and may lead to malfunctions and the life of the

lamp being shortened.

5. The screen is made of plastic

Handle the screen very carefully as it can scratch easily. Do not rub, hit or press on it with any

hard objects. When the screen is dirty, gently wipe it with a soft cloth. Refer to the Appendix for

details on how to clean the screen.

6. Caution! Warm air from the air ducts

This unit has an air duct for cooling. The duct will blow warm air while the television is operating.

When placing the television, make sure not to locate it too close to wallpaper. The warm air

could cause the color of the wallpaper to change. Also, take care to keep children and pets

away from the warm air ducts. Long exposure to the warm air from the ducts could cause a

minor burn.

7. Caution! Moving this television

When lifting this television, Do not hold by the screen frame. Holding the screen frame could

cause it to detach, causing the television to fall.

8. Do not replace the lamp immediately after use

The lamp becomes extremely hot during use. If the lamp is touched immediately after use

before it has a chance to cool down, there is a danger of burns. Be careful when handling the

lamp.

9. Do not touch the lamp glass

If the lamp is used when there is dirt from ﬁngers on the lamp glass, there is a possibility of the

lamp breaking. Be careful not to touch the lamp glass.

10. ILA element characteristics

Do not project still pictures or pictures that have still segments for a long period of time. The still

parts of the picture may remain on the screen. This is a characteristic of ILA elements and not a

malfunction. The picture will disappear over time.

11. Condensation

When a heater is turned on or the television is moved from a cold place to a hot place, droplets

of water may form on the lamp and screen. This is called condensation. If the television is used

while this condensation is still present, the picture may seem distorted, and the inside of the

screen may become dirty. In this case, wait until the condensation has gone before using the

television.

12. Do not open the rear cabinet of this television

This television has a DIGITAL-IN terminal. Opening up the rear cabinet will violate the copyright

of the program or software shown on the television. Please do not open the rear cabinet.

13. Usable Time

Do not keep the TV on for more than 24 hours consecutively. There is a possibility of the life of

the lamp being shortened.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Button Functions . . . . . . . . . . 62

Multi Screen Function . . . . . . . . . . 62

Split . . . . . . . . . . . . . . . . . . 62

Index . . . . . . . . . . . . . . . . . 63

Freeze . . . . . . . . . . . . . . . . . . 63

Swap . . . . . . . . . . . . . . . . . 63

Select . . . . . . . . . . . . . . . . . . 63

Menu . . . . . . . . . . . . . . . . . . 63

OK . . . . . . . . . . . . . . . . . . . 63

Back . . . . . . . . . . . . . . . . . . . 63

Power . . . . . . . . . . . . . . . . . . 64

Number Buttons . . . . . . . . . . . . . 64

Important Safety Precautions . . 2

Warnings . . . . . . . . . . . . . . . 5

Quick Setup . . . . . . . . . . . . . . 9

Unpacking your TV . . . . . . . . . . . . 9

TV Models . . . . . . . . . . . . . . . . 10

TV Remote Control . . . . . . . . . . . 12

Getting Started . . . . . . . . . . . . . 13

The Remote Control . . . . . . . . . . 13

Connecting Your Devices . . . . . . . 14

Interactive Plug In Menu . . . . . . . . 24

Programming your remote . . . . . . . 27

Tune

Onscreen Menus . . . . . . . . . 31

Using the Guide . . . . . . . . . . . . . 31

Onscreen Menu System . . . . . . . . . 32

Initial Setup . . . . . . . . . . . . . 34

Auto Tuner Setup . . . . . . . . . . . . 34

Channel Summary . . . . . . . . . . . . 35

Channel Label . . . . . . . . . . . . . 36

V-Chip . . . . . . . . . . . . . . . . . . 37

Set Lock Code . . . . . . . . . . . . . 43

Language . . . . . . . . . . . . . . . . 44

Closed Caption . . . . . . . . . . . . . 45

Auto Shut Off . . . . . . . . . . . . . . 47

XDS ID . . . . . . . . . . . . . . . . . 47

Noise Muting . . . . . . . . . . . . . . 48

Front Panel Lock . . . . . . . . . . . . 48

V1 Smart Input . . . . . . . . . . . . 49

Video Input Label . . . . . . . . . . 50

Position Adjustment . . . . . . . . . . . 51

Power Indicator . . . . . . . . . . . . . 51

Digital-In . . . . . . . . . . . . . . . 52

Digital-In1 Audio . . . . . . . . . . . 52

Digital Setup . . . . . . . . . . . . . 53

Picture Adjust . . . . . . . . . . . . . 55

Picture Settings . . . . . . . . . . . . . 55

Color Temperature . . . . . . . . . . . . 55

Color Management . . . . . . . . . . . . 56

Dynamic Gamma . . . . . . . . . . . . . 56

Smart Picture . . . . . . . . . . . . . . . 56

Digital VNR . . . . . . . . . . . . . . . . 57

MPEG NR . . . . . . . . . . . . . . . 57

Reset . . . . . . . . . . . . . . . . . . 57

Sound Adjust . . . . . . . . . . . . . 58

Sound Settings . . . . . . . . . . . . . 58

Turn On Volume . . . . . . . . . . . . . 58

Volume Limit . . . . . . . . . . . . . . 58

Reset . . . . . . . . . . . . . . . . . . 58

Clock/Timers . . . . . . . . . . . . . . . . 59

Set Clock . . . . . . . . . . . . . . . . 59

On/Off Timer . . . . . . . . . . . . . . . 60

Lamp Timer Reset . . . . . . . . . . . . 61

Input . . . . . . . . . . . . . . . . . . . 64

TheaterPro . . . . . . . . . . . . . . . 64

Return+/TV . . . . . . . . . . . . . . . 65

Sound . . . . . . . . . . . . . . . . . . 65

Video Status . . . . . . . . . . . . . . . 66

Natural Cinema . . . . . . . . . . . . . 66

Sleep Timer . . . . . . . . . . . . . . . 67

ML/MTS . . . . . . . . . . . . . . . . . 67

Muting . . . . . . . . . . . . . . . . . . 67

Display . . . . . . . . . . . . . . . . . 68

C.C. . . . . . . . . . . . . . . . . . . . 68

Channel +/- . . . . . . . . . . . . . 68

Volume +/- . . . . . . . . . . . . . 68

Favorite . . . . . . . . . . . . . . . . 69

Aspect . . . . . . . . . . . . . . . . . 70

Aspect Ratios . . . . . . . . . . . . . 70

TV/CATV Slide Switch . . . . . . . . . . 72

VCR/DVD Slide Switch . . . . . . . . . 72

VCR Buttons . . . . . . . . . . . . . . . 72

DVD Buttons . . . . . . . . . . . . . . . 72

Light . . . . . . . . . . . . . . . . . . 72

D/A (Digital/Analog) . . . . . . . . . 73

Sub Channel . . . . . . . . . . . . . 73

Guide . . . . . . . . . . . . . . . 73

OSD Information . . . . . . . . . . 74

Weak Signal . . . . . . . . . . . . . 74

No Program . . . . . . . . . . . . . 74

Invalid Signal . . . . . . . . . . . . . 74

Lamp Replacement . . . . . . . . 75

Troubleshooting . . . . . . . . . . 80

Specifications . . . . . . . . . . 82

Warranty . . . . . . . . . . . . . 84

Authorized Service Center . . . 85

Notes . . . . . . . . . . . . . 86

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Unpacking your TV

Thank you for your purchase of a JVC Color Television. Before you begin setting up your new

television, please check to make sure you have all of the following items. In addition to this

guide, your television box should include:

Remote Control x 1

Television x 1

Batteries x 2

POWER

TV CATV VCR DVD

ASPECT

MULTI SCREEN

SPLIT

INDEX SELECT

SWAP DISPLAY

FREEZE

INPUT

D/A

ML/MTS

SLEEP

TUNE

RETURN+/TV

THEATER

PRO

VIDEO

SUB

FAVORITE

C.C.

STATUS

CHANNEL

NATURAL

CINEMA

SOUND

LIGHT

MUTING

GUIDE

Note: Your television

and/or remote

VOL

BACK

VCR CHANNEL

VCR DVD

POWER TV VCR

PREV NEXT

REW

PLAY

control may differ

from the examples

illustrated here.

LAMP

POWER

REC

STOP

PAUSE

OPEN CLOSE

STILL PAUSE

RM-C18G

We recommend that before you start using your new television, you read your entire User’s

Guide so you can learn about your new television’s many great features. If you’re anxious to

start using your television right away, a quick setup guide follows on the next few pages.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

TV Models

Before you connect your television to another device, please refer to the proper diagrams for

your specific TV and remote. These will help assist you in understanding how to connect your

television to another device, as well as use the remote to set up your television.

Rear Panel Diagram

S-VIDEO

VIDEO

R - AUDIO - L

INPUT-1

INPUT-2

INPUT-3

HDMI 1

OVER

OPTICAL OUT

Digital Audio

S-VIDEO

OVER

SERVICE

ONLY

DIGITAL-IN

INPUT-1

INPUT-2

AUDIO

OUTPUT

INPUT-3

PC IN

(D-SUB)

75Ω

(VHF/UHF)

LICENSED UNDER THE

FOLLOWING U.S. PATENTS

6,183,091

6,419,362

Note:

The terminal labeled "SERVICE ONLY", is exclusively used to update the software version.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Front Panel Diagram

LAMP

POWER

LAMP

LAMP LED

POWER

POWER BUTTON

POWER LED

• For information on the LED, see page 79.

Side Panel Diagram

INPUT

OPERATE

INPUT

–

CHANNEL

VOLUME

VIDEO

L/MONO

AUDIO

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Remote Control

POWER

TV CATV VCR DVD

ASPECT

MULTI SCREEN

SPLIT

INDEX SELECT

SWAP DISPLAY

FREEZE

INPUT

D/A

ML/MTS

SLEEP

RETURN+/TV

TUNE

THEATER

PRO

VIDEO

SUB

FAVORITE

C.C.

STATUS

CHANNEL

NATURAL

CINEMA

SOUND

LIGHT

MUTING

GUIDE

VOL

BACK

VCR CHANNEL

VCR DVD

POWER TV VCR

PREV NEXT

REW

PLAY

REC

STOP

PAUSE

OPEN CLOSE

STILL PAUSE

RM-C18G

• For information on remote control buttons, see pages 62 - 73.

• SUB CHANNEL and GUIDE buttons are for digital channels. If your TV is connected to an

ATSC antenna or Digital Cable, you can use these buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Getting Started

These quick setup pages will provide you, in three easy steps, with the basic information you

need to begin using your new television right away. If you have questions, or for more detailed

information on any of these steps, please consult other sections of this manual.

Step 1 – The Remote Control

Before you can operate your remote

control, you first need to install the

batteries (included).

Slide the cover on the back of the

remote down towards the bottom of

the remote control. Insert two batteries

(included) carefully noting the “+” and

“–” markings, placing the “–” end in the

unit first. Slide the cover back into place.

When you change the batteries, try to complete the task within three minutes. If you take

longer than three minutes, the remote control codes for your VCR, DVD, and/or cable

box/satellite receiver may have to be reset. See pages 27 - 30.

Key Feature Buttons

The four key feature buttons at the center of the remote can be

MUTING

GUIDE

BACK

used for basic operation of the television. The top and bottom

buttons will scan forward and back through the available

channels. To move rapidly through the channels using

JVC’s Hyperscan feature, press and hold CH+ or CH–. The

channels will zip by at a rate of five channels per second. The

right and left buttons will turn the volume up or down. These

buttons are also marked with four arrows and are used with

JVC’s onscreen menu system. To use the onscreen menus,

press the MENU button.

VOL

POWER

Basic Operation

Turn the television on and off by pressing the POWER button at the top right corner

of the remote. The POWER LED will light blue. If this is the first time you are

turning on the TV, the interactive plug-in menu appears.

TV CATV

• Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if

you need to operate a cable box.

MUL

• Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to DVD to

control a DVD player. Please see pages 27 - 30 for instructions on programming

your remote control to operate a cable box, VCR or DVD player.

VCR DVD

Note:

• If the lamp replacement message appears when you turn the television ON, see page 76.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Step 2 – Connecting Your Devices

To make these connections, you will use plugs like the ones illustrated below.

Component Cables

Coaxial Cables

Composite Cables

Audio Cables

Used to connect an external

antenna or cable TV system to your

TV.

Used to connect audio/video

devices like VCRs, DVD players,

stereo amplifiers, game consoles,

etc.

S-Video Cable

Used to make video connections

with S-Video VCRs, Camcorders

and DVD players.

Notes:

• These connections are examples.

• After you are finished connecting your devices, plug the power cord into the nearest power

outlet and turn on the TV.

• If you follow these diagrams and the television does not work properly, contact your local

cable operator.

• To connect a DVD player, see VCR Connection. A DVD player is optional

• If you have a satellite television system, refer to the satellite TV manual.

No VCR Connection

Cable or Antenna

Coaxial Cable

Output

75Ω

(VHF/UHF)

TV Rear Panel

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

VCR Connection

Notes:

• Green, blue and red are the most common colors for DVD cables. Some models may vary

colors. Please consult the user’s manual for your DVD player for more information.

• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete

one set of connections (DVD or audio output) before starting the other to avoid accidentally

switching the cables.

• You may also connect the DVD player to Input 1.

Diagram #1

VCR

Cable or Antenna

Output

Cable Cable

Out

OUT

Coaxial Cable

75Ω

(VHF/UHF)

S-VIDEO

VIDEO

R - AUDIO - L

INPUT-1

INPUT-2

INPUT-3

HDMI 1

OVER

VIDEO

TV Rear Panel

S-VIDEO

OVER

INPUT-1

INPUT-2

DVD Player (Optional)

AUDIO OUT

VIDEO OUT

Green Blue Red

Note:

• If this connection setup does not work for you, try the connection setup on page 16.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Diagram #2

VCR

Cable or Antenna

Output

Cable Cable

In Out

OUT

Two-Way Splitter

Coaxial Cable

OUT OUT

S-VIDEO

VIDEO

R - AUDIO - L

INPUT-1

INPUT-2

INPUT-3

HDMI 1

OVER

VIDEO

S-VIDEO

75Ω

(VHF/UHF)

OVER

INPUT-1

TV Rear Panel

INPUT-2

DVD Player (Optional)

AUDIO OUT

VIDEO OUT

Green Blue Red

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connecting to a Camcorder

You may connect a camcorder, game console or other equipment to your television by using

the side input jacks (Input 4) located on the side of the television. You can also connect

these using the television’s rear input jacks, using the same instructions.

INPUT

OPERATE

INPUT

–

Camcorder

CHANNEL

VOLUME

VIDEO

L/MONO

AUDIO

1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on

the side of the TV.

2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on

the side of the TV.

3) Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on

the side of the TV.

Note:

• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the

L/MONO on the side of the TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connecting to an External Amplifier

TV Rear Panel

Speaker

Amplifier

AUDIO

OUTPUT

1) Connect a white cable from the LEFT AUDIO OUTPUT on the back of the TV to the

LEFT AUDIO INPUT on the amplifier.

2) Connect a red cable from the RIGHT AUDIO OUTPUT on the back of the TV to the

RIGHT AUDIO INPUT on the amplifier.

Notes:

• Refer to your amplifier’s manual for more information.

• You can use AUDIO OUTPUT for your home theater system.

• You can not output audio using the AUDIO OUTPUT under the following conditions:

1) When you have digital sound from an HDMI device connected to the HDMI 1 or HDMI 2

connection on the back of your TV. (See page 20).

2) When you have analog sound from a DVI device connected to the AUDIO IN "HDMI 1"

connection. (See page 19).

Connecting to an amplifier using your optical output

You can connect an amplifier that has an optical digital input terminal by using an optical digital

cable from the optical output. The signal that is output can be PCM or Dolby Digital.

OPTICAL OUT

Digital Audio

TV Rear Panel

Amplifier

1) Connect the optical cable from the back of the TV to the back of the amplifier.

Notes:

• This terminal can only output digital audio.

• In order to use the optical output connection, select PCM or Dolby Digital on Digital Sound

Menu. See page 54.

• Refer to your owners manual on using your amplifier.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connecting to a Digital TV Receiver

By connecting a Digital TV Receiver, high definition pictures can be displayed on your TV in

their digital form.

DTV device

Digital Out Audio Out

AUDIO

HDMI 1

DIGITAL-IN

HDMI to DVI Cable

After the connections have been made,

tighten the screw to secure the cables.

1) Connect the HDMI to DVI Cable from the DIGITAL OUT on the back of your DTV decoder, to

the HDMI1 DIGITAL-IN on the back of your television.

2) Connect a red cable from the "R AUDIO OUT" on the back of your DTV Device, to the

HDMI 1 "R AUDIO" input terminal.

3) Connect a white cable from the "L AUDIO OUT" on the back of your DTV Device, to the

HDMI 1 "L AUDIO" input terminal.

• The digital-in terminal is not compatible with the picture signal of a personal computer.

• Use a HDMI to DVI cable (commercially available) in order to digitally connect the television

with a DTV decoder.

Notes:

• If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance

may be slightly shifted. Access the “DIGITAL-IN” in the initial setup menu to adjust it. (Refer

to page 52.)

• When you do the above connection, set DIGITAL-IN1 AUDIO in the Initial Setup menu to

ANALOG. See "DIGITAL-IN1 AUDIO", page 52.

• The Analog Audio input can only be used with the HDMI 1 input.

• When setting the “DIGITAL AUDIO – ANALOG / DIGITAL” menu setting on the TV, please note

that this setting only effects the HDMI 1 jack and that if you use a DVI to HDMI adapter this

connection must be made to the HDMI 1 along with analog audio cables.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connecting to an HDMI Compatible Device

By connecting an HDMI compatible device, high definition pictures can be displayed on your

TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI

compatible devices.

HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all

digital audio/video interface. HDMI provides and interface between any audio/video source,

such as a set-top box, DVD player, A/V receiver or an audio and/or video monitor, such as a

digital television (DTV).

HDMI Compatible Device

TV Rear Panel

Digital Out

R - AUDIO - L

HDMI 1

DIGITAL-IN

HDMI Cable

1) Connect the HDMI Cable from the DIGITAL OUT on the back of your DTV or HDMI device, to

the HDMI1 DIGITAL-IN on the back of your television.

Notes:

• When you do the above connection, set DIGITAL-IN1 AUDIO in the Initial Setup menu to

DIGITAL. See "DIGITAL-IN1 AUDIO", page 52.

• Some decoders may not respond depending on the equipment that you have connected

when it is connected to the HDMI.

• If the HDMI output device signal is changed (for example, 480i/60Hz is changed to

480p/60Hz), the screen may turn green and there may be some distortion for a short time

until the signal becomes stable.

• When you have an HDMI device connected to the HDMI 1 connection on the back of your

TV, your TV detects it, and blocks the analog audio signal coming into the "HDMI 1" jacks.

Therefore, you can not hear any analog sound from the other device connected to the

"HDMI 1" jacks, while you are viewing the images from the HDMI device.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connecting to an AV Receiver using your television's

V1 Smart Input

By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture

sources from many different devices, without having to change or use the other input

connections on your TV. This allows you to free up the other input connections so you can

connect more devices to your television.

TV Rear Panel

S-VIDEO

VIDEO

R - AUDIO - L

AV Receiver

INPUT-1

INPUT-2

INPUT-3

HDMI 1

OVER

MONITOR

OUT

S-VIDEO

OVER

MONITOR OUT

INPUT-1

INPUT-2

1) Connect an S-Video Cable from the AV Receiver's MONITOR OUT, to the S-Video INPUT-1

on the back of your television.

2) Connect a Yellow Composite Cable from the AV Receiver's MONITOR OUT, into the VIDEO

INPUT-1 on the back of your television.

3) Connect a Green Component Cable from the AV Receiver's Y MONITOR OUT, into the Y

VIDEO INPUT-1 on the back of your television.

4) Connect a Blue Component Cable from the AV Receiver's PB MONITOR OUT, into the Pb

VIDEO INPUT-1 on the back of your television.

5) Connect a Red Component Cable from the AV Receiver's PR MONITOR OUT, into the Pr

VIDEO INPUT-1 on the back of your television.

Note:

• Please refer to your AV Receiver instruction manual for more information on connecting your

speakers and other devices like a DVD player.

• Use your AV Receiver's remote to switch to the different devices you have connected.

• Some AV Receivers may not respond when the V1 Smart Input function is turned on, see

page 49.

• If you have video connections for each input device connected to your AV Receiver, you

should not connect them using both S-Video and Composite connection at the same time

when you are using V1 Input as the V1 Smart Input. In this case we recommend using the

S-Video connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Connecting to the computer

This TV can be used as a computer screen. Use a commercially available D-SUB cable to

connect the TV's PC INPUT terminal to the computer's analog RGB output terminal. If you

want to listen to the sound from the computer, use a commercially available RCA cable to

connect the INPUT-3 audio input terminal to the computer's audio output terminal.

TV Rear Panel

S-VIDEO

VIDEO

R - AUDIO - L

INPUT-1

INPUT-2

INPUT-3

HDMI 1

OVER

S-VIDEO

OVER

INPUT-1

INPUT-2

AUDIO

OUTPUT

INPUT-3

PC IN

(D-SUB)

Notes:

• Refer to your computer manual for a detailed explanation of the connections concerning your

computer.

• Make sure that the connectors are facing the correct way when connecting.

• After connecting, tighten the two screws to fix the connectors in place.

Looking at the images from a computer

After starting the computer, press the INPUT button to choose INPUT-3. You can listen to the

sound when the sound from the computer is connected to the INPUT-3 AUDIO input terminal.

Notes:

• When the sound from the computer is connected to INPUT-3 by choosing external input

INPUT-3, the sound from the computer can be listened to, but the images from the computer

cannot be seen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Table of signals for each type of computer

Resolution

Vertical

Frequency

(Hz)

Horizontal

Frequency

(kHz)

640 x 480

(VGA)

60.0

31.5

1024 x 768

(XGA)

60.0

48.4

• Only the above formats are supported.

• Even with the above formats at 60 Hz, some problems may be experienced depending on

the quality of the synchronous signal. (Depending on the quality, some pictures may not be

displayed correctly).

• Apple Macintosh* computers are not supported.

When a picture is not displayed

With some computers, some problems can be solved by changing the settings. Check the

computer's refresh rate and set it to 60Hz. Computers that cannot set the refresh rate to 60

Hz, can not be used with this TV. Refer to the computer's instruction manual.

*Apple Macintosh is a registered trademark of Apple Computer, Inc.

Note:

• If you are inputting a PC signal that is invalid, "Invalid Signal" will appear on the TV screen.

It appears when the input is PC and it is a single screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Step 3 – The Interactive Plug In Menu

When you turn your television on for the first time the interactive plug-in menu will appear. The

plug-in menu helps you to get your TV ready to use by letting you set your preferences for:

• The language in which you want the onscreen menus to appear.

• Setting the TV’s clock to the correct time so your timer functions will work properly. You can

choose “AUTO” or “MANUAL” for setting the clock.

• The auto tuner setup of which channels you wish to receive.

We recommend you complete the interactive plug-in items before you start using your

television.

Notes:

• The interactive plug-in menu setting does not appear if your TV has been turned on before.

In this case use the onscreen menus to perform these settings. See pages 45, 59 and 34.

• If you press the Menu button while setting up the interactive plug-in menu, it will skip over it.

Language

After the “JVC INTERACTIVE PLUG IN MENU” has been displayed, the TV automatically

switches to the LANGUAGE settings. You can choose to view your onscreen menus in three

languages: English, French (Français) or Spanish (Español).

LANGUAGE/LANGUE/IDIOMA

√®

To choose a language:

(English, Français or Español)

†

To NEXT (To set clock)

ENGLISH

SELECT OPERATE

EXIT

(To be continued...)

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Auto Clock Set

Before you use any of your TV’s timer functions, you must first set the clock. You may

precisely set your clock using the XDS time signal broadcast by most public analog

broadcasting stations. If you do not have this in your area, you will have to set the clock

manually. See manual clock set below. To set the clock using the XDS signal:

√®

†

To choose AUTO

To TIME ZONE

SET CLOCK

√®

To select your time zone: (Atlantic, Eastern,

Central, Mountain, Pacific, Alaska or

Hawaii)

MODE

TIME

TIME ZONE

D.S.T.

AUTO

-- ----

ATLANTIC

†

√®

†

To move to D.S.T. (Daylight Savings Time)

To turn D.S.T. ON or OFF

To NEXT (To Auto Tuner Setup)

SELECT OPERATE

EXIT

Notes:

• D.S.T. can be used when it is set to ON in the SET CLOCK menu.

• Only when the MODE is set to AUTO, the Daylight Savings Time feature automatically

adjusts your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00

am on the first Sunday in April. The clock will move back one hour at 2:00 am on the last

Sunday in October.

• You will have to reset the clock after a power interruption. You must set the clock before

operating any timer functions.

Manual Clock Set

To set your clock manually (without using the XDS signal), choose MANUAL. If you choose

AUTO, see auto clock set above.

√®

†

To choose MANUAL

To TIME

SET CLOCK

√®

†

√®

†

To set the hour

To minute

To set the minute

To TIME ZONE

MODE

TIME

TIME ZONE

D.S.T.

MANUAL

-- ----

ATLANTIC

√®

To select your time zone: (Atlantic, Eastern,

Central, Mountain, Pacific, Alaska or

Hawaii)

START CLOCK

SELECT OPERATE

EXIT

†

To move to D.S.T. (Daylight Savings Time)

√®

†

To turn D.S.T. ON or OFF

To START CLOCK

Note:

• You will have to reset the clock after a power interruption. You must set the clock before

operating any timer functions.

(To be continued...)

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Auto Tuner Setup

In auto tuner setup, the TV automatically scans through all available channels, memorizing the

active ones and skipping over blank ones or channels with weak signals. This means when you

scan (using the CHANNEL +/– buttons) you will receive only clear, active channels.

AUTO TUNER SETUP

√®

To choose CABLE or AIR (or SKIP when

you skip Analog Auto Tuner Setup)

TUNER MODE

AIR

†

To START

After Analog Auto Tuner Setup is finished, Digital Auto

Tuner Setup starts.

START

SELECT OPERATE

EXIT

NOW

PROGRAMMING !

Now Programming...

When the setup is finished, "THANK YOU ! SETUP IS NOW COMPLETE" is displayed. Your

quick setup is now complete. You can now begin watching your television, or you can continue

on in this guide for more information on programming your remote control, or using the

JVC onscreen menu system to customize your television viewing experience.

Notes:

• If you want to cancel the Auto Tuner Setup, press the MENU button.

• Noise muting will not work during Auto Tuner Setup.

• If you choose SKIP, it finished without doing the Auto Tuner Setup.

Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending

on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is

normal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Programming your remote control

You can program your remote to operate your cable box, satellite receiver, VCR or DVD

player by using the instructions and codes listed below. If the equipment does not respond to

any of the codes listed below or to the code search function, use the remote control supplied

by the manufacturer.

Cable Box or Satellite Codes

The remote control is programmed with cable box and satellite codes for power on/off,

channel up/down, and 10 key operation.

1) Find the cable box or satellite brand from the list of codes shown below.

2) Slide the 2-way selector switch to “CATV”.

3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10

key pad.

4) Release the DISPLAY button, and confirm the operation of the cable box/satellite receiver.

• If your cable or satellite box does not respond to the first code, try the others listed. If it does

not respond to any code, try the search codes function, on page 30.

Cable Box

Codes

024

Digital

Codes

Cable Box

Codes

Satellite

Systems

ABC

Archer

Puser

RCA

Realistic

Regal

032

032, 025

051, 032

022, 051

058, 059

024, 032, 025

029

061, 070

032

058, 064, 040,

041, 042, 045,

068

Echostar

(Dish Network) 115

100, 113, 114,

Cableview

Citizen

Curtis

Diamond

Eagle

Eastern

GC Brand

Gemini

General

Instrument/Jerrold 026, 027, 020,

021, 022, 057,

Express VU

G.E.

100, 113

106

Regency

Rembrandt

034

G.I.

108, 120, 121,

122

037, 032, 051,

038

034

032, 051

022, 043

065, 024, 025,

Gradiente

Hitachi

112

Samsung

051

104, 111

Scientific Atlanta 057, 058, 059

SLMark

051, 047

051, 056

032, 051

HNS (Hughes)

104

Sprucer

Stargate

Magnavox

102, 103

023, 072, 074

Panasonic

Philips

105

102, 103, 116

Hamlin

040, 041, 042,

045, 058, 064

049, 024

Telecaption

Teleview

Texscan

Tocom

067

Hitachi

Macom

047, 051

044

Primestar

108

049, 050, 051,

054

Proscan

RCA

106, 109, 110

035, 036, 066,

074

Magnavox

033

030

032, 051

039, 037, 048

Sony

107

Memorex

Movietime

Oak

Toshiba

Unika

050, 048

032, 025

Star Choice

Toshiba

104, 108

101, 104, 117,

118, 119

Universal

Videoway

Viewstar

Zenith

022, 032

052

Panasonic

055, 056, 060,

071, 073

063

Uniden

102, 103

Paragon

Philips

029, 030

063, 046

046

028, 029, 030,

052, 053, 031,

069

Zenith/Drake

Satellite

Pioneer

Pulsar

047, 062

051, 032

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

VCR Codes

The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward,

rewind, pause, record, channel up/down operation.

1) Find the VCR brand from the list of codes shown below.

2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.

3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10

key pad.

4) Release the DISPLAY button, and confirm the operation of the VCR.

• If your VCR does not respond to the first code, try the others listed. If it does not respond to

any of the codes, try the search codes function on page 30.

• After you program your remote, some VCR buttons may not work properly. If so, use the

VCR’s remote.

• To record, hold down the REC button on the remote and press PLAY.

Codes

035

027, 032, 095

029, 072, 073, Memorex

074

Codes

VCR

Admiral

Aiwa

Akai

VCR

Marantz

Marta

003, 004, 005

064

024, 067

038, 040, 047,

048, 041, 042

058, 045, 093

038, 040, 047,

048, 041, 042,

078, 090

Samsung

037, 060, 062,

033, 089

089

003, 026, 020,

052

Samtron

Sansui

MGA

Audio Dynamic 003, 005

Sanyo

Scott

063, 067, 091,

071

Bell & Howell

Broksonic

Canon

CCE

Citizen

063, 071

020, 026, 094

023, 025

043

064

063, 029, 064

045, 024, 027,

093

043, 059, 024,

092

003, 004, 005

045, 093

043, 026, 077,

061, 025, 042,

020, 076

063, 066, 067,

065, 071, 091

Minolta

Mitsubishi

059, 060, 062,

067, 038, 040,

047, 048, 026,

020

063, 064, 065,

066, 058

Multitech

NEC

047, 027, 062

003, 004, 005,

000

024, 023

028, 021, 035,

064

026, 020

023, 024, 021,

022

024, 058, 045,

063, 003, 004,

005, 093

058, 005, 045,

093

Sears

Craig

Curtis Mathes

Olympic

Sharp

035, 036, 080,

088

075

Optimus

Daewoo

Shintom

Orion

Panasonic

DBX

Dimensia

Emerson

Signature 2000 027, 035

Singer

Sony

075

028, 029, 030,

053, 054, 055

027

031, 023, 024,

027

Penney

SV 2000

Sylvania

Fisher

Funai

Pentax

Philco

027, 026, 020,

000

033, 045, 024

037, 051, 049,

050, 089

064

031, 024, 027,

023, 026, 020,

043

031, 023, 024,

086

Symphonic

Tashiro

Tatung

027, 081

064

003, 004, 005

003, 004, 027,

005

021, 022, 023,

024

G.E.

Go Video

Philips

Teac

Pioneer

Proscan

023

Goldstar

Technics

Teknika

045, 058, 023,

024, 031, 046,

059, 060, 093,

033, 087

021, 022, 023,

024

033, 024, 063,

036, 067, 040,

027

033, 045, 058,

023, 024, 031,

046, 059, 060,

083, 084, 085,

087, 093, 096

Gradiente

083, 084, 081,

000, 001

024, 027, 070

Hitachi

023, 045, 058,

093, 027, 081

Thomson

Toshiba

033, 096

Quasar

Instant Replay 024, 023

059, 046, 079

Radio Shack

Jensen

JVC

003

Vector Research 005

003, 004, 005,

000, 001, 002,

006, 007

Wards

Yamaha

Zenith

035, 036, 067,

044, 064

063, 003, 004,

005

044, 082, 064,

094

RCA

Kenwood

003, 004, 064,

005

064

Realistic

024, 063, 036,

067, 040, 027

LXI

027, 064, 058,

065, 066, 063,

067

Magnavox

031, 023, 024,

086

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

DVD Codes

The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward,

rewind, previous/next chapter, tray open/close, and still/pause operation.

1) Find the DVD player brand from the list of codes shown below.

2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.

3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10

key pad.

4) Release the DISPLAY button, and confirm the operation of the DVD player.

• If your DVD player does not respond to the first code, try the others listed. If it does not

respond to any of the codes, try the search codes function on page 30.

• After you program your remote, some DVD buttons may not work properly. If so, use the

DVD player’s remote.

DVD Player

Aiwa

Codes

DVD Player

Mintek

Codes

057

DVD Player

Sharp

Codes

028

043

Apex

040, 054,

055

Mitsubishi

025

Silvania

038

Bose

058

Next Base

Onkyo

056

SMC

Sony

048

024, 045,

046, 047

Denon

020, 037

041, 052

Funai

038

032

053

Oritron

044

Technics

Thomson

Toshiba

020

021

023

Go–Video

Panasonic

Philips

020

Harman

Kardon

023, 036

Hitachi

JVC

031

Pioneer

Polk Audio

Raite

022

036

033

Venturer

Vialta

051

050

000

Kenwood

035, 020

Wave

042

Yamaha

Zenith

020, 049

027, 032

KLH

Konka

Koss

051

039

050

RCA

Sampo

Samsung

021, 026

034

030

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Setup

Search Codes

Cable/Satellite Search Codes Function

1) Slide the first 2-Way Mode Selector switch to CATV.

2) Press the POWER and RETURN+/TV buttons. Hold for at least three seconds and release.

3) Press the POWER button on the remote, and see if the cable or satellite box responds.

4) If there was a response, press RETURN+/TV. The codes are now set. If there was no

response, repeat Step 3. If you repeat Step 3 a total of 80 times without a response, use

the remote control that came with your equipment.

5) Press RETURN+/TV to exit.

VCR/DVD Search Codes Function

1) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR” or

“DVD”.

2) Press the VCR or DVD POWER and RETURN+/TV buttons. Hold for at least three seconds

and release.

3) Press the VCR or DVD POWER button, and see if the VCR or DVD responds.

4) If there was a response, press RETURN+/TV. The codes are now set. If there was no

response, repeat Step 3. If you repeat Step 3 a total of 80 times for the VCR (40 times for

the DVD player), and there is no response, use the remote control that came with your

equipment.

5) Press RETURN+/TV to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Using the Guide

Certain symbols are used throughout this guide to help you learn about the features of your

new television. The ones you will see most frequently are:

π† Up and Down arrows mean press the CH+ or CH– buttons. Pressing the CH+ or CH–

buttons let you:

• Move vertically in a main menu screen

• Move through a submenu screen

• Move to the next letter, number, or other choice in a submenu

• Back up to correct an error

• Scan through TV channels (when not in a menu screen)

√® Left and right arrows mean press the VOLUME+ or VOLUME- buttons to move left or right

to:

• Select a highlighted menu item

• Select an item in a submenu

• Select numbers in certain menu options

• Turn the volume up or down (when not in a menu screen)

The “press button” icon means you should press the button named on your remote

control. (Button names appear in SMALL CAPITAL LETTERS.)

The “helping arrow” icon points to the highlighted or selected item in a menu.

To bring up the onscreen menu, press the MENU button on the remote control. The item that

appears in green is the one currently selected. If you use the Menu button on the TV’s side

panel instead of the remote, an additional menu screen showing VIDEO STATUS and ASPECT

will appear between INITIAL SETUP and PICTURE ADJUST. The “interactive plug-in menu” will

appear the first time the TV is plugged in.

INITIAL SETUP

AUTO TUNER SETUP

CHANNEL SUMMARY

V-CHIP

SET LOCK CODE

(4/5)

EXIT

SELECT OPERATE

Note:

• Menus shown in this book are illustrations, not exact replications of the television’s onscreen

displays.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

The Onscreen Menu System

Your television comes with JVC’s onscreen menu system. The onscreen menus let you make

adjustments to your television’s operation simply and quickly. Examples of the onscreen

menus are shown on the next page. Detailed explanations on using each menu follow later in

this guide. For information about the interactive plug-in Menu, see pages 24 - 26.

The Onscreen Menu System

To open the onscreen menu system, press the MENU button on the remote control. You

navigate within the onscreen menus by using the four directional arrow buttons on the remote

control. (These buttons are also the CH +/– and VOL +/– buttons. Channel and volume functions

will not operate when the onscreen menu is active).

The selected feature and option on a menu screen are highlighted in a different color.

Selected Option

(Green)

ENG. FRAN. ESP.

LANGUAGE

CLOSED CAPTION

Selected Option

(Blue)

To move to a different feature use the π† arrows to move up or down the list. When you

press the up arrow at the top of the list or the down arrow at the bottom, the next menu screen

will appear. Use the arrows √ ® to select an option from the highlighted feature. Pressing

MENU on the remote control will close the onscreen menu system and return you to normal

television viewing.

Each menu and its features will be discussed in the following pages of this guide.

Notes:

• If you do not press any buttons for about a minute, the onscreen menu will automatically

shut off.

• Button names in this guide are shown in SMALL CAPITAL LETTERS.

• Menus may appear in different sizes onscreen depending on the aspect ratio selected.

• Some menu items may not appear in menu screens when certain aspect ratios or inputs

are selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Press the MENU button

INITIAL SETUP

DIGITAL SETUP

AUTO TUNER SETUP

CHANNEL SUMMARY

V-CHIP

SET LOCK CODE

(5/5)

(4/5)

EXIT

SELECT OPERATE

EXIT

SELECT OPERATE

INITIAL SETUP 05

INITIAL SETUP 04

INITIAL SETUP

PICTURE ADJUST

TINT

COLOR

PICTURE

BRIGHT

DETAIL

STANDARD

LANGUAGE

ENG. FRAN. ESP.

CLOSED CAPTION

AUTO SHUT OFF

XDS ID

OFF

(3/5)

SELECT OPERATE

(1/3)

EXIT

SELECT OPERATE

EXIT

INITIAL SETUP 03

PICTURE ADJUST 01

INITIAL SETUP

PICTURE ADJUST

OFF

NOISE MUTING

STANDARD

FRONT PANEL LOCK

V1 SMART INPUT

VIDEO INPUT LABEL

POSITION ADJUSTMENT

POWER INDICATOR

COLOR TEMPERATURE

COLOR MANAGEMENT

DYNAMIC GAMMA

SMART PICTURE

LOW

(2/5)

(2/3)

SELECT OPERATE

EXIT

SELECT OPERATE

EXIT

INITIAL SETUP 02

PICTURE ADJUST 02

INITIAL SETUP

DIGITAL-IN

PICTURE ADJUST

DIGITAL VNR

MPEG NR

STANDARD

SIZE1

DIGITAL

AUTO

DIGITAL-IN1 AUDIO

RESET

(1/5)

EXIT

(3/3)

SELECT OPERATE

EXIT

INITIAL SETUP 01

PICTURE ADJUST 03

CLOCK TIMERS

SET CLOCK

SOUND ADJUST

TURN ON VOLUME

VOLUME LIMIT

BASS

ON OFF TIMER

TREBLE

BALANCE

LAMP TIMER RESET

RESET

(2/2)

EXIT

(1/2)

EXIT

SELECT OPERATE

EXIT

SELECT OPERATE

SOUND ADJUST 02

SOUND ADJUST 01

CLOCK/TIMERS

• The DIGITAL-IN menu can only be displayed when a 480p picture signal is input to the

digital-in terminal and the picture is being displayed on the screen.

• When the Menu button on the TV side panel is pressed, the FRONT PANEL CONTROL menu

between INITIAL SETUP 05 and PICTURE ADJUST 01 will appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Auto Tuner Setup

The auto tuner setup function is described on page 26 as the interactive plug-in menu. If you

need to run the auto tuner setup again, follow the steps below.

Press the MENU button

AUTO TUNER SETUP

π†

√®

To AUTO TUNER SETUP

To operate

TUNER MODE

AIR

To choose CABLE or AIR

Press the OK button to start

PRESS OK TO START

OPERATE

EXIT

The auto tuner is finished when the message PROGRAMMING OVER! appears onscreen.

Note:

• Auto Tuner Setup in Digital Cable will take approximately 14 minutes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Channel Summary

Channel summary allows you to customize the line-up of channels received by your TV.

Regarding analog channels, you can add or delete channels from the line-up or prevent any

unauthorized viewers from watching any or all 181 channels. Regarding digital channels, the

only channels that will appear are the ones that are broadcasting.

Press the MENU button

To CHANNEL SUMMARY

To operate

Analog Channels

CHANNEL SUMMARY

π†

CHNO. SCAN

√®

HBO

The Channel summary screen will now be displayed with

the channels set to scan marked with an “√”. Regarding

analog channels, you can delete channels from the scan

by removing the “√”. If any channels were missed during

auto tuner setup and you wish to add them, you may by

placing an “√” next to the channel number.

MTV

A&E

SELECT

OPERATE

EXIT

Digital Channels

• Digital channels can not be added to the channel

summary if the auto tuner setup did not find them.

Channel Summary Digital

CH No.

D3-1

Scan

Station Name

CH-1

π†√® To the SCAN column

Press the OK button to include or delete from

scan

D3-2

CH-2

D3-3

CH-3

D22-1

CH-1

Press the MENU button when finished

^OKOperate

^BACKBack

^MENUExit

Select

Note:

• The number of a digital channel may change, depending on the time of some broadcastings.

If this channel existed and now had disappeared, the lock channel or scanned channel by the

channel summary for that channel will be cancelled.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

How to set the channel label. (This is only for analog broadcasting.)

Press the MENU button

π†

√®

π†

To CHANNEL SUMMARY

To operate

To the ID column

CHANNEL 09

RESET

Press the OK button to enter

PRESS TO FINISH

√®

π†

To select the character you want

To move to the next space

SELECT OPERATE

EXIT

...continue to follow these directions for all four

spaces

Press the OK button to finish

Your characters are now set

Press the MENU button when finished

If you want to reset the characters you set:

Press the MENU button

π†

√®

π†

To CHANNEL SUMMARY

To operate

To the ID column

Press the OK button to enter

To select RESET

π†

Press the OK button to finish

Your characters are now reset

Notes:

• You can use characters for: Alphabet, numbers, marks and spaces.

• It is possible to set the maximum of 40 channel labels.

• If you try to set more than the 40 maximum, the message "MEMORY OVERFLOW" will

appear.

You can block access to a channel by activating the channel lock.

Press the MENU button

π†

To CHANNEL SUMMARY

To operate

√®

π†√® To the Lock Column (

)

Press the ZERO button to lock or unlock that channel

Press the MENU button when finished

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Channel Guard Message

When a viewer attempts to watch a guarded channel, the following message appears:

To watch a channel that you have locked, enter the

THIS CHANNEL IS LOCKED BY

Lock Code using the 10 key pad.

If the wrong code is entered, the message

“INVALID LOCK CODE!” will flash on the screen.

CHANNEL GUARD.

PLEASE ENTER LOCK CODE BY

10 KEY PAD TO UNLOCK IT.

The channel cannot be accessed until the correct code

is entered.

NO. - - - -

Notes:

• Once a channel has been unlocked, it will remain unlocked until the television is turned off.

• See also “Set Lock Code”, page 43.

V-Chip

Your TV is equipped with V-Chip technology which enables you to block channels or content

that you feel to be inappropriate for children, based on US and Canada rating guidelines.

V-Chip has no effect on video signals from DVD discs or Camcorder connection.

Note: Some programs, and movies are broadcast without a ratings signal. Even if you set

up V-CHIP ratings limits, these programs will not be blocked. See page 38 for information on

how to block unrated programs.

Note (for Canadian viewers): The V-Chip function is based on specifications designed for

the United States and therefore may not work properly in Canada.

You can customize the V-Chip settings of your television to match your personal tastes. The

V-Chip menu below is the starting point for your V-Chip settings

You can use US V-Chip settings (for programming broadcast from the United States), Canadian

V-Chip settings (for programming broadcast from Canada), and movie ratings. You may use

any or all of the settings (US V-Chip, Canada V-Chip, Movie ratings). Descriptions for setting

each of the three V-Chip formats appear in the next six pages along with descriptions of the

rating categories.

To access the rating categories:

Press the MENU button

V-CHIP

OFF

π†

√®

To V-CHIP

To operate (Lock icon

SET US TV RATINGS

SET MOVIE RATINGS

SET CANADIAN RATINGS ENG

SET CANADIAN RATINGS FRE

UNRATED

will appear)

Press ZERO to access the V-Chip menu

VIEW

√®

To turn V-Chip ON or OFF (V-Chip must be

turned ON for rating settings to operate)

π†

To move to SET US TV RATINGS,

SET MOVIE RATINGS, or

SELECT OPERATE

EXIT

SET CANADIAN RATINGS (see following

pages for descriptions of each item)

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Unrated Programs

Unrated programming refers to any programming which does not contain a rating signal.

Programming on television stations which do not broadcast rating signals will be placed in the

“Unrated Programming” category.

Examples of Unrated programs:

• Emergency Bulletins

• News

• Public Service Announcements

• Sports

• Locally Originated Programming

• Political Programs

• Religious Programs

• Weather

• Some Commercials

Note:

• TV programs or movies that do not have rating signals will be blocked if the unrated category

is set to BLOCK.

Directions to Block Unrated Programs

You can block programs that are not rated.

Press the MENU button

V-CHIP

OFF

π†

To V-CHIP

SET US TV RATINGS

SET MOVIE RATINGS

SET CANADIAN RATINGS ENG

SET CANADIAN RATINGS FRE

UNRATED

√®

To operate (The lock icon

appears)

Press ZERO to access V-Chip setup options

VIEW

π†

To UNRATED

√®

To VIEW or BLOCK

SELECT OPERATE

EXIT

Press MENU when done

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

US V-Chip Ratings

U.S. PARENTAL RATING SYSTEMS

Programs with the following ratings are appropriate for children.

❒ TV Y is Appropriate for All Children

Programs are created for very young viewers and should be suitable for all ages, including

children ages 2 - 6.

❒ TV Y7 is for Older Children

Most parents would find such programs suitable for children 7 and above. These programs

may contain some mild fantasy violence or comedic violence, which children should be able

to discern from reality.

Programs with the following ratings are designed for the entire audience.

❒ TV G stands for General Audience

Most parents would find these programs suitable for all age groups. They contain little or no

violence, no strong language, and little or no sexual dialog or situations.

❒ TV PG Parental Guidance Suggested

May contain some, but not much, strong language, limited violence, and some suggestive

sexual dialog or situations. It is recommended that parents watch these programs first, or

with their children.

❒ TV 14 Parents Strongly Cautioned

Programs contain some material that may be unsuitable for children under the age of 14

including possible intense violence, sexual situations, strong coarse language, or intensely

suggestive dialog. Parents are cautioned against unattended viewing by children under 14.

❒ TV MA Mature Audiences Only

These programs are specifically for adults and may be unsuitable for anyone under 17

years of age. TV MA programs may have extensive V, S, L, or D.

Viewing Guidelines

In addition to the ratings categories explained above, information on specific kinds of content

are also supplied with the V-Chip rating. These types of content may also be blocked. The

content types are:

• V/FV is for VIOLENCE/FANTASY VIOLENCE

• S stands for SEXUAL CONTENT

• L stands for strong LANGUAGE

• D stands for suggestive DIALOG

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Setting US V-Chip Ratings

Press the MENU button

V-CHIP

OFF

π†

√®

To V-CHIP

SET US TV RATINGS

SET MOVIE RATINGS

SET CANADIAN RATINGS ENG

SET CANADIAN RATINGS FRE

UNRATED

To operate (lock icon

appears)

Press ZERO to access the V-Chip menu

VIEW

√®

π†

√®

To turn V-Chip ON or OFF

To move to SET US TV RATINGS

To operate

SELECT OPERATE

EXIT

Directions to set US V-Chip Ratings

Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and

press the π† or √® to move the cursor to the correct location. Press OK to turn the locking

feature on or off. An item is locked if the

icon appears instead of a “—”.

For example. To block viewing of all TV 14 shows, move the cursor to the top row of that

column and add a lock icon. Once you’ve put a lock on the top row, everything in that column

is automatically locked.

SET US TV RATINGS

π†√® To the TV 14 Column

Press the OK button to lock

MA 14

Press the MENU button when finished

V/FV

Note:

• If you want to change the setup, move the cursor to

the top column and change the lock icon to “—” by

pressing OK again. You may then select individual

categories to block.

EXIT

SELECT

OPERATE

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Movies Ratings

❒ NR – Not Rated

This is a film which has no rating. In many cases these films were imported from countries

which do not use the MPAA ratings system. Other NR films may be from amateur producers

who didn’t intend to have their film widely released.

NR (Not Rated) Programming may contain all types of programming including children’s

programming, foreign programs, or adult material.

❒ G – General Audience

In the opinion of the review board, these films contain nothing in the way of sexual content,

violence, or language that would be unsuitable for audiences of any age.

❒ PG – Parental Guidance

Parental Guidance means the movie may contain some contents such as mild violence,

some brief nudity, and strong language. The contents are not deemed intense.

❒ PG-13 – Parents Strongly Cautioned

Parents with children under 13 are cautioned that the content of movies with this rating may

include more explicit sexual, language, and violence content than movies rated PG.

❒ R – Restricted

These films contain material that is explicit in nature and is not recommended for

unsupervised children under the age of 17.

❒ NC-17 – No One Under 17

These movies contain content which most parents would feel is too adult for their children

to view. Content can consist of strong language, nudity, violence, and suggestive or explicit

subject matter.

❒ X – No One under 18

Inappropriate material for anyone under 18.

Directions to set Movie (MPAA) Ratings

Press the MENU button

π†

√®

To V-CHIP

To operate (Lock icon

appears)

Press ZERO to access V-Chip setup options

π†

√®

To SET MOVIE RATINGS

To enter movies menu

SET MOVIE RATINGS

For example: To block viewing of programming rated

NC-17 shows, move the cursor to the NC-17 column and

add a lock icon. Once you've put a lock on the NC-17

column, X column is automatically locked.

_C17

_G13

π†√® To the NC-17 Column

Press the OK button to lock

Press the MENU button to finish

EXIT

SELECT

OPERATE

• If you want to change the setup, move the cursor to the

column and change the lock icon to “—” by pressing OK again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Canadian V-Chip Ratings

❒ E – Exempt

Exempt programming includes: news, sports, documentaries and other information

programming, talk shows, music videos, and variety programming.

❒ C – Programming Intended for Children

Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive

behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or

unrealistic in nature.

❒ C8+ – Programming Intended for Children 8 and Over

Violence

Guidelines: Any realistic depictions of violence will be infrequent, discreet, of low intensity

and will show the consequences of the acts. There will be no offensive language, nudity or

sexual content.

❒ G – General Audience

Programming will contain little violence and will be sensitive to themes which could affect

younger children.

❒ PG – Parental Guidance

Programming intended for a general audience, but which may not be suitable for younger

children. Parents may consider some content not appropriate for children aged 8-13.

❒ 14+ – 14 Years and Older

Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and

early teens. Programming may contain mature themes and scenes of intense violence.

❒ 18+ – Adult

Material intended for mature audiences only.

Directions to set Canadian V-Chip Ratings

Press the MENU button

π†

√®

To V-CHIP

To operate (lock icon

appears)

Press ZERO to access V-Chip setup options

π†

√®

To SET CANADIAN RATINGS ENG (for English)

To enter ratings menu

For example: To block viewing of programming rated

14+ shows, move the cursor to the 14+ column and

add a lock icon. Once you've put a lock on the 14+

column, 18+ column is automatically locked.

SET CANADIAN RATINGS ENG

18+

14+

√®

To the 14+ Column

Press the OK button to lock

Press the MENU button to finish

EXIT

SELECT

OPERATE

Notes:

• If you want to change the setup, move the cursor to the column and change the lock icon to

“—” by pressing OK again.

• For instructions on “SET CANADIAN RATINGS FRE (in French)”, please see page 42 in the

French side of this user’s guide.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Set Lock Code

Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes

preset with a lock code of “0000”. You may change the code to any four-digit number you wish.

To change the lock code, follow the steps below.

Press the MENU button

SET LOCK CODE

LOCK CODE

π†

To SET LOCK CODE

To operate (lock icon

0000

√®

appears)

Press ZERO to access the lock code

The first digit will be highlighted

PRESS

TO FINISH

SELECT OPERATE

EXIT

√®

π†

To select the number

To move to the next digit

Continue to follow these directions for all four numbers

Press the OK button to finish (your lock code is now set)

Press the Menu button when finished

When a viewer attempts to watch a blocked channel, this message appears:

THIS PROGRAMMING EXCEEDS

YOUR RATING LIMITS.

PLEASE ENTER LOCK CODE BY

10 KEY PAD TO UNLOCK IT.

NO. - - - -

The channel will remain blocked until the correct lock code is entered (see above for

information on setting your lock code).

Notes:

• After a power interruption you must reset the lock code.

• Write your lock code number down and keep it hidden from potential viewers.

• If you forget the lock code, a new code may be set using the steps listed above.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Language

The language function is described on page 24 as the interactive plug-in menu. If you need to

choose the language again, follow the steps below.

Press the Menu button

INITIAL SETUP

LANGUAGE

CLOSED CAPTION

AUTO SHUT OFF

XDS ID

π†

To LANGUAGE

ENG. FRAN. ESP.

√®

To choose a language: ENG. (English),

FRAN. (French) or ESP. (Spanish)

OFF

Press the MENU button when finished

(3/5)

SELECT OPERATE

EXIT

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Closed Caption

Many broadcasts now include an onscreen display of dialog called closed captions. Some

broadcasts may also include displays of additional information in text form. Your television can

access and display this information using the closed caption feature. To activate the closed

caption feature, follow the steps below. There are three methods. When you are watching

analog channels, you can perform Analog Setting of closed caption. When you are watching

digital channels, you can perform Digital Auto Setting or Digital Manual Setting.

Analog Setting

Press the MENU button

CLOSED CAPTION

MODE

π†

√®

π†

√®

π†

√®

To CLOSED CAPTION

To enter

TEXT

CC1

CAPTION

TEXT

To MODE

To select CAPTION or TEXT in MODE

To CAPTION or TEXT

To select a caption (CC1 to CC4) or text

channel (T1 to T4)

PRESS TO FINISH

SELECT OPERATE

EXIT

Press the OK button to save

Press the MENU button when finished

Digital Auto Setting

Press the MENU button

Digital Closed Caption

Preview

π†

√®

π†

√®

To CLOSED CAPTION

To enter

To Type

Closed Caption Sample

Type

AUTO

Service

Appearance

To select Auto, Advanced or Basic

Auto: Shows closed caption a priority for

digital channels over analog channels. It is

set automatically.

Cancel

Set

Operate ^BACKBack

^MENUExit

Select

Advanced: Shows only the digital closed

caption.

Basic: Shows only the analog closed

caption.

Digital Closed Caption

Preview

Appearance

Closed Caption Sample

Appearance Mode

Auto

π†

√®

π†

√®

π†

To Service

Font

To select 1, 2, 3, 4, 5 or 6

To Appearance

To enter

To select Auto

To Set

Colors

Opacities

Cancel

Set

^BACKBack

^MENUExit

Select

Operate

Press the OK button to save

The font/type and color are set automatically.

Press the MENU button when finished

Note:

• If you want to cancel the settings, select cancel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Digital Manual Setting

Press the MENU button

Digital Closed Caption

Preview

Appearance

π†

To CLOSED CAPTION

Closed Caption Sample

√®

π†

√®

π†

√®

π†

√®

π†

√®

π†

√®

To enter

To Type

Appearance Mode

Manual

Font

Colors

Opacities

To select Auto, Advanced or Basic

To Service

To select 1, 2, 3, 4, 5 or 6

To Appearance

To enter

To select Manual

To Font

To enter

To select Font Size or Font Style

To select the setting you like

Cancel

Set

^BACKBack

^MENUExit

Select

Operate

Digital Closed Caption

Preview

Appearance

Closed Caption Sample

Font Size

Appearance Mode

Standard

Auto

Manual

Font Style

Font

Colors

Font Size: Auto, Standard, Large or Small

Cancel

Set

Opacities

Cancel

Font Style: Auto, Serif Mono, Serif, Sanserif mono,

Sanserif, Casual, Cursive or Small Capital

π†

Set

^BACKBack

^MENUExit

Select

Operate

To Set

Press the OK button to save

π†

√®

π†

√®

To Colors

To enter

To select Text, Edge or Background

To select the setting you like

Digital Closed Caption

Preview

Appearance

Closed Caption Sample

Text

Appearance Mode

White

Black

Set

Manual

Edge

Auto, White, Black, Red, Green, Blue,

Yellow, Magenta or Cyan

Font

Background

Cancel

Colors

Opacities

π†

To Set

Cancel

Set

^BACKBack

^MENUExit

Press the OK button to save

Select

Operate

π†

√®

π†

√®

To Opacities

To enter

To select Text/Edge or Background

To select Auto, Transparent, Translucent, Solid

or Flashing

To Set

All fonts used for digital closed

caption and digital menus are

licensed from Monotype Imaging

Inc.

π†

Press the OK button to save

Press the MENU button when finished

Notes:

• Closed caption subtitles are usually found on closed caption channel CC1. Some programs

may include additional text information which is usually found on text channel T1. The other

channels are available for future use.

• Closed captioning may not work correctly if the signal being received is weak or if you are

playing a video tape.

• Most broadcasts containing closed captioning will display a notice at the start of the program.

• To select the mode, press the C.C. button. See page 68.

• When ZOOM aspects like PANORAMA or CINEMA are selected, Digital Closed Captions

may be cut off or distorted.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Auto Shut Off

This function automatically shuts off your TV when there is no signal from the channel the

TV is on.

INITIAL SETUP

Press the MENU button

LANGUAGE

ENG. FRAN. ESP.

π†

√®

To AUTO SHUT OFF

To turn ON or OFF

CLOSED CAPTION

AUTO SHUT OFF

XDS ID

OFF

Press the MENU button when finished

• If the channel that you have on does not receive a

signal for more than one minute, the blinking text

“NOT RECEIVING A SIGNAL AUTO SHUT OFF

IN 9 MIN.” appears on the screen, and starts the

countdown. If no signal is being received within 10

minutes, the TV shuts itself off.

(3/5)

SELECT OPERATE

EXIT

XDS ID

XDS ID Display provides a channel’s call letters, the network’s name, and even a program

name. The XDS ID information is provided by the broadcaster.

INITIAL SETUP

Press the MENU button

LANGUAGE

ENG. FRAN. ESP.

π†

√®

To XDS ID

To turn ON or OFF

CLOSED CAPTION

AUTO SHUT OFF

XDS ID

OFF

Press the MENU button when finished

(3/5)

SELECT OPERATE

EXIT

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menu

Noise Muting

This feature inserts a blank gray screen over channels which are not broadcasting or are too

weak to be received clearly.

Press the MENU button

INITIAL SETUP

π†

√®

To NOISE MUTING

To turn noise muting ON or OFF

OFF

NOISE MUTING

FRONT PANEL LOCK

V1 SMART INPUT

VIDEO INPUT LABEL

POSITION ADJUSTMENT

POWER INDICATOR

Press the MENU button when finished

LOW

(2/5)

Notes:

SELECT OPERATE

EXIT

• Noise muting will not work during auto tuner setup or

when you operate channel summary.

• Noise muting will not work when the digital TV is displayed.

Front Panel Lock

This allows you to lock the keys on the side of the TV, so that a child may not accidentally

change your viewing preferences.

Press the MENU button

INITIAL SETUP

NOISE MUTING

π†

√®

To FRONT PANEL LOCK

To turn ON or OFF

OFF

FRONT PANEL LOCK

V1 SMART INPUT

VIDEO INPUT LABEL

POSITION ADJUSTMENT

POWER INDICATOR

Press the MENU button when finished

You can turn off this feature in the following ways:

LOW

(2/5)

• Unplug the power cord, and plug it back in. Do this if

your batteries die, or you lose your remote control.

SELECT OPERATE

EXIT

• Use the remote control.

• Press the MENU button on the side of the TV for more than 3 seconds. In this case, the OSD

for FRONT PANEL LOCK will appear.

Note:

• To turn ON/OFF the TV, press the power button for more than 3 seconds. This feature will

remain ON.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

V1 Smart Input

This feature is used if you have connected an AV Receiver to your television. By turning this

feature on, your television can automatically detect the signal source from your components

that are connected to your AV Receiver.

Press the MENU button

INITIAL SETUP

NOISE MUTING

π†

√®

To V1 SMART INPUT

To turn ON or OFF

OFF

FRONT PANEL LOCK

V1 SMART INPUT

VIDEO INPUT LABEL

POSITION ADJUSTMENT

POWER INDICATOR

Press the MENU button when finished

LOW

Notes:

(2/5)

• If you do not have an AV Receiver connected to your

television, turn this feature OFF.

SELECT OPERATE

EXIT

• Some AV Receivers may not work with this function.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Video Input Label

This function is used to label video input connections for the onscreen displays.

Press the MENU button

To VIDEO INPUT LABEL

To enter

INITIAL SETUP

π†

√®

π†

√®

OFF

NOISE MUTING

FRONT PANEL LOCK

V1 SMART INPUT

VIDEO INPUT LABEL

POSITION ADJUSTMENT

POWER INDICATOR

To select the desired video input

LOW

To select the desired preset input label (see

chart below)

(2/5)

SELECT OPERATE

EXIT

Press the OK button to save

VIDEO INPUT LABEL

Press the MENU button when finished

VCR

DVD

SAT

GAME

STB

VIDEO-1

VIDEO-2

VIDEO-3

VIDEO-4

DIGITAL-IN1

STB

DIGITAL-IN2

PRESS TO FINISH

SELECT OPERATE

EXIT

Preset

Labels

Select when...

VCR

DVD

PVR

You have a VCR connected to the video input

You have a DVD connected to the video input

You have a Personal Video Recorder connected to the video input

D-VHS You have a Digital VCR connected to the video input

STB

SAT

AMP

You have a Set-top Box connected to the video input

You have a Satellite Receiver connected to the video input

You have an Amplifier connected to the video input

GAME You have a Video Game connected to the video input

CAM

DISC

You have a Video Camera connected to the video input

You have a Video Disc player connected to the video input

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Position Adjustment

Position adjustment allows you to adjust the position of the picture on the screen vertically

when the aspect is set to panorama or cinema.

Press the MENU button

π†

√®

π†

To POSITION ADJUSTMENT

To enter

To adjust the position

Press the MENU button to finish

Notes:

RESET

EXIT

OPERATE

• To reset the adjustment to the center, press the

OK button.

• When the arrow disappears, while you are adjusting the position, the position is at its

maximum limit.

• If you select regular size, slim size and full size with aspect or Multi Screen, position

adjustment option is not seen.

• When you change the screen size, perform the position adjustment again.

• Position adjustment allows you to adjust the screen position vertically and horizontally when

the aspect is set Panorama Zoom or Cinema Zoom for 1080i and 720p signals, or when PC

mode is set.

Power Indicator

Power indicator allows you to adjust the brightness of the power indicator

Press the MENU button

INITIAL SETUP

OFF

NOISE MUTING

FRONT PANEL LOCK

V1 SMART INPUT

VIDEO INPUT LABEL

POSITION ADJUSTMENT

POWER INDICATOR

π† To POWER INDICATOR

√®

To adjust POWER INDICATOR LOW, HIGH

or OFF

Notes :

• When OFF is selected :

The LED disappears if you have a TV signal.

The LED is lit as “LOW” when there is no TV signal.

LOW

(2/5)

SELECT OPERATE

EXIT

• When the On Timer turns ON, the LED is lit as

"LOW" when you turn the power off.

• If you set a timer on the TV, the power indicator will light even if the TV is on stand by.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Digital-In

The DIGITAL-IN option can only be displayed in the INITIAL SETUP menu when an HDMI480p

picture signal is being input to the DIGITAL-IN terminal. This option adjusts the position when

an HDMI or DVI 480p picture signal is being displayed on the screen. There are two types of

HDMI480p picture signals: 640x480 and 720x480. If the displayed picture is slightly shifted, the

position can be adjusted by selecting either SIZE1 or SIZE2.

INITIAL SETUP

Press the MENU button

DIGITAL-IN

π†

√®

π†

To DIGITAL-IN

SIZE1

DIGITAL

DIGITAL-IN1 AUDIO

To enter

To select AUTO, SIZE1 or SIZE2

Press the MENU button to finish

(1/5)

SELECT OPERATE

EXIT

Notes:

• The DIGITAL-IN menu can only be displayed when a HDMI or DVI 480p picture signal is

input to the Digital-In terminal and the picture is being displayed on the screen.

• You can select AUTO only when the signal is 480p for HDMI. When you select AUTO, the

televison will select "SIZE1" or "SIZE2" automatically.

Digital-in1 Audio

This feature is used if you have a DTV or HDMI compatible component connected to your TV.

Press the MENU button

INITIAL SETUP

DIGITAL-IN

DIGITAL-IN1 AUDIO

π†

√®

To DIGITAL-IN1 AUDIO

To select ANALOG, DIGITAL or AUTO

SIZE1

DIGITAL

Press the Menu button when ﬁnished

Notes:

(1/5)

• If your DTV or HDMI component is capable of digital

audio and video, choose DIGITAL. If your DTV or HDMI

SELECT OPERATE

EXIT

component is capable of analog audio and digital video, choose ANALOG.

• Refer to your DTV or HDMI component’s instruction manual for more information.

• When you select AUTO, the television will select "ANALOG" or "DIGITAL" automatically,

depending on the audio input from the HDMI.

• When you select DIGITAL, select PCM on Digital Sound menu. See page 54.

• When your input is DIGITAL-IN2, DIGITAL-IN AUDIO cannot be selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Digital Setup

Use this function when you are receiving a digital broadcast.

Press the MENU button

Digital Setup

Antenna Level

π†

To DIGITAL SETUP

To enter

Digital Sound

PCM

√®

Software Version

The onscreen will appear

Notes:

Software Update

• Software Update will only appear when the USB

memory is inserted into the USB connector.

Operate ^BACKBack

^MENUExit

Select

• If you are watching an analog channel, you can still

access the digital setup menu at anytime, while you are doing this, the background screen

will turn blank. In this case, the tuner will switch to digital, since you are accessing the digital

setup menu.

Antenna Level

Confirms the present antenna level.

Antenna Level

Press the MENU button

π†

To DIGITAL SETUP

To enter

^BACKBack

^MENUExit

√®

π†

To Antenna Level

To enter

√®

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Digital Sound

You can select the optical digital sound output, either PCM or Dolby Digital when your TV is

connected to an amplifier that has Dolby Digital decoder. If you select Dolby Digital, you can

enjoy listening in 5.1ch sound when watching digital broadcasts.

Press the MENU button

π†

√®

To DIGITAL SETUP

To enter

π†

To Digital Sound

√®

To select PCM or DOLBY DIGITAL

Press the MENU button when finished

Notes:

• If your amplifier does not have Dolby Digital decoder, select PCM. If you don't select PCM, it

cannot output the sound from the speakers.

• For connecting an amplifier using the optical output, see page 18.

Manufactured under license from Dolby Laboratories. "Dolby", and

the double-D symbol are trademarks of Dolby Laboratories.

Software Version

You can confirm the Software Version.

Press the MENU button

π†

√®

To DIGITAL SETUP

To enter

π†

√®

To Software Version

To enter

Select close when you are finished confirming your software version

Press the MENU button when finished

Software Update

At first, connect the USB memory into the USB connector. This function will appear only when

the USB memory is inserted into the USB connector.

Press the MENU button

π†

√®

π†

√®

π†

To DIGITAL SETUP

To enter

To Software Update

To enter

Checks the card if it needs an update or not

Press the MENU button when finished

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Picture Settings

These settings allow you to change and adjust the way the picture appears on your television.

TINT

Tint allows you to adjust the levels of red and green in your TV picture.

COLOR

The color function lets you make all the colors in the TV picture appear either more vivid or

subtle.

PICTURE

Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker

or brighter picture overall.

BRIGHT

You can adjust the overall brightness of the TV picture with the Bright control.

DETAIL

The Detail feature adjusts the level of fine detail displayed in the picture.

Adjust the Picture Settings

Press the MENU button

PICTURE ADJUST

π†

To TINT, COLOR, PICTURE, BRIGHT or

DETAIL

To enter

TINT

COLOR

PICTURE

BRIGHT

DETAIL

STANDARD

√ ®

+02

TINT

SELECT OPERATE

(1/3)

EXIT

√ ®

π†

To adjust the setting

To move to the next setting

Press the MENU button when finished

Color Temperature

You can decide how strong or dull the colors appear on the TV screen.

Press the MENU button

COLOR TEMPERATURE

LOW

HIGH

π†

√®

π†

To COLOR TEMPERATURE

To enter

To set LOW or HIGH

Press the MENU button when finished

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Color Management

This TV supports the COLOR MANAGEMENT function to ensure dull colors are compensated

to produce natural hues.

Press the MENU button

COLOR MANAGEMENT

OFF

π†

√®

π†

To COLOR MANAGEMENT

To enter

To select the mode “ON" or "OFF"

Press the MENU button when finished

Dynamic Gamma

JVC's Dynamic Gamma Circuitry (DGC) makes it easier to see dark areas when a picture

has many dark areas, and makes it easier to see the bright areas when a picture has many

bright areas. DGC is turned on, DGC analyzes and adjusts the total level of picture brightness

balance, especially in dark areas where the level of grayscale is often lost, turning completely

to black DGC automatically enhances the detail in these dark areas providing a more dynamic

image with ﬁner detail, so the optimum picture settings are automatically set for each picture.

Normally use with DGC on.

Press the MENU button

DYNAMIC GAMMA

OFF

π†

√®

π†

To DYNAMIC GAMMA

To enter

To turn ON or OFF

Press the MENU button when finished

Smart Picture

Smart Picture detects the APL (Average Picture Level) and adjusts the contrast suitable for

what you are watching.

Press the MENU button

SMART PICTURE

OFF

π†

√®

π†

To SMART PICTURE

To enter

To select the mode "ON" or "OFF"

Press the MENU button when finished

Note:

• When you have "DYNAMIC" selected in the "VIDEO STATUS", Smart Picture is not selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Digital VNR

This function can be selected to change the effect of Digital VNR (Video Noise Reduction).

Press the MENU button

DIGITAL VNR

AUTO

MIN

π†

√®

π†

To DIGITAL VNR

To enter

To select the effect you like

MAX

OFF

AUTO: adjusts the effect of VNR automatically

MIN: adjusts the effect of VNR to minimum

MAX: adjusts the effect of VNR to Maximum

OFF: turns the effect of VNR off

Press the MENU button when finished

Note:

• If it is in PC, Digital VNR will not be displayed.

MPEG NR

This function effects the block noise removal and mosquito NR (Noise Reduction)

simultaneously.

Press the MENU button

MPEG NR

π†

√®

π†

To MPEG NR

To enter

To select ON or OFF

OFF

Press the MENU button when finished

Note:

• When you are receiving digital channels, block noise removal will have no effect.

Reset

Reset resets all picture adjustments (tint, color, picture, bright, detail, color temperature, dig.

noise clear, Color Management, Dynamic Gamma and Smart Picture) at once to the default

settings.

Press the MENU button

PICTURE ADJUST

π†

√®

To RESET

To enter

DIGITAL VNR

MPEG NR

STANDARD

AUTO

The onscreen menu disappears for a moment,

and then the settings are reset to the default

setting for all the picture adjustments.

RESET

(3/3)

Press the MENU button when finished

SELECT OPERATE

EXIT

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Sound Settings

These settings allow you to change and adjust the sound on your television.

BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with

the bass adjustment.

TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio.

BALANCE – Adjust the level of sound between the TV’s left and right speakers with the

balance setting.

Adjust the Sound Settings

Press the MENU button

SOUND ADJUST

π†

√ ®

π†

To BASS, TREBLE or BALANCE

To adjust the setting

To move to the next setting

BASS

TREBLE

BALANCE

Press the MENU button when finished

(1/2)

EXIT

Note:

SELECT OPERATE

• You can reset the sound adjustments (BASS, TREBLE

and BALANCE) you set at once as the default setting when you select reset. See page 57.

• You can adjust BALANCE only when A.H.S.+ is off. See page 65.

Turn On Volume

Turn On Volume allows you to set the volume level when you turn the TV on.

Press the MENU button

π†

√®

To TURN ON VOLUME

To set

Current

Press the MENU button to finish

Volume Limit

Volume Limit allows you to set the maximum volume level.

Press the MENU button

π†

√®

To VOLUME LIMIT

To set the maximum volume level

Press the MENU button to finish

Reset

Reset resets all Sound Adjustments (Bass, Treble and Balance) at once to the default settings.

See page 57 on how to use reset.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

Set Clock

The set clock function is described on page 25 as the interactive plug-in menu. You can choose

to set the clock automatically or manually. If you need to set the clock again, follow the steps

below.

Press the MENU button

π†

√®

To SET CLOCK

To enter

When you set the clock automatically, choose AUTO by pressing the

√

arrows.

π†

√®

To TIME ZONE

To select your time zone

SET CLOCK

ATLANTIC

CENTRAL

EASTERN

HAWAII

MOUNTAIN

MODE

TIME

AUTO

--: ----

ALASKA

PACIFIC

TIME ZONE

D.S.T.

ATLANTIC

π†

√®

To D.S.T. (daylight savings time)

To turn D.S.T. ON or OFF

PRESS TO FINISH

Press OK to finish

SELECT OPERATE

EXIT

Press the MENU button when finished

When you set the clock manually, choose MANUAL by pressing the

√

arrows.

π†

√®

π†

√®

π†

√®

To move to the hours

To set the hours

To move to minutes

To set the minutes

To TIME ZONE

SET CLOCK

MODE

TIME

TIME ZONE

D.S.T.

MANUAL

-- ----

ATLANTIC

To select your time zone:

(Atlantic, Eastern, Central, Mountain, Pacific,

Alaska or Hawaii)

PRESS TO START CLOCK

SELECT OPERATE

EXIT

π†

To D.S.T. (daylight savings time)

√®

To turn D.S.T. ON or OFF

Press OK to start clock

THANK YOU !!

Press the MENU button when finished

Notes:

• D.S.T. can be used when it is set to ON in the SET CLOCK menu.

• Only when the MODE set to AUTO, the Daylight Savings Time feature automatically adjusts

your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00 am on

the first Sunday in April. The clock will move back one hour at 2:00 am on the last Sunday in

October.

• You will have to reset the clock after a power interruption. You must set the clock before

operating any timer functions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen Menus

On/Off Timer

The on/off timer lets you program your television to turn itself on or off. You can use it as an

alarm to wake up, to help you remember important programs, or as a decoy when you’re not

home.

Press the MENU button

ON/OFF TIMER

ON TIME

OFF TIME

CHANNEL

ON VOLUME

MODE

7:00 PM

10:00 PM

CURRENT

EVERYDAY

π†

√®

To ON/OFF TIMER

To enter (begins with ON TIME)

To set the hour (AM/PM) you want the TV to

turn on

ON/OFF TIMER

†

√®

†

To move to minutes

To set the minutes

PRESS TO FINISH

SELECT OPERATE

EXIT

To accept ON TIME and move to OFF TIME (the time the TV will turn off). Set the

OFF TIME the same way as ON TIME

†

√®

†

To accept OFF TIME and move to CHANNEL

To select channel

To ON VOLUME

√®

†

To set the volume level

To move to MODE

√®

Choose ONCE or EVERYDAY

†

To ON/OFF TIMER

√®

Choose YES to accept the timer setting, choose NO if you don’t wish to accept

Press the OK button to finish

Press the MENU button to exit the menu

Notes:

• The on/off time cannot be set to locked or guarded channels.

• In order for the on/off timer to work, the clock must be set.

• After a power interruption, the timer settings must be reset.

• The digital channel is set only set to the marked channel in channel summary.

• The blocked channel cannot be set.

Download from Www.Somanuals.com. All Manuals Search And Download.

Onscreen menus

Lamp Timer Reset

The lamp replacement message will appear when you need to change the lamp. After you

replace the lamp, you need to reset the timer which is built into your television.

Press the MENU button

CLOCK TIMERS

SET CLOCK

π†

To LAMP TIMER RESET

To Enter

ON OFF TIMER

√®

LAMP TIMER RESET

The following message will appear.

SELECT OPERATE

EXIT

PRESS OK TO RESET THE LAMP

TIMER.

Press the OK button while the above message appears on the television screen.

THE LAMP TIMER IS RESET

SUCCESSFULLY.

The lamp timer has now been reset.

Notes:

• You can use the Lamp Timer Reset only after replacing the lamp.

• See Page 75 for instructions on lamp replacement.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Multi Screen Function

Your television has two kinds of screen: SPLIT (2 channels) and INDEX (12 channels).

Note: After you press any multiscreen buttons, if you press the menu button, only the picture

adjust screen will appear.

Split

Activate the split-screen option by pressing SPLIT on

the remote control. The channel (or input) you were

watching before pressing SPLIT will appear on the

left, the new channel will appear on the right. The

sound will continue to come from the main screen

channel (or input). To turn split-screen off and return

to normal television viewing, press SPLIT again or

press the BACK button.

V-1

MAIN SCREEN

PICTURE

SPLIT SCREEN

PICTURE

Notes:

• If the signal that you are watching is coming from the HDMI input, you cannot enter the

SWAP or INDEX mode.

• Main Screen and Split Screen will not display the same channel or input at the same time.

• Split screen will not display digital channel.

• You can enter the SPLIT mode when the screen is in NORMAL or INDEX mode.

• Split-screen functions will not work with locked channels or channels blocked by V-Chip

ratings limits. A gray screen will display instead.

• With split screen, the picture from the component terminal and DIGITAL-IN terminal will

not be displayed.

• The aspect of MAIN CHANNEL PICTURE becomes 16:9 when you input the picture of

480p, 720p and 1080i from the component terminal and DIGITAL-IN terminal.

• After you press the SELECT button, and select SPLIT SCREEN when you press the

OK button, select normal screen. If you don’t operate, the MAIN CHANNEL SCREEN will

be automatically selected about 8 seconds later.

• Aspect does not work in Split mode.

• When it is PC output, Main and Split screen will not be displayed.

• When you are in PC mode, SPLIT, INDEX or FREEZE can not be used.

• When you press the Menu button in Split mode, it appears only as Picture Adjust menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Index

This allows you to quickly look at up to 12 channels at a time so that you can decide which one

to watch.

Notes:

• Only analog channel input signal will be displayed.

• You can watch the channel added in channel summary. See page 35.

Freeze

Pressing the FREEZE button causes the screen to change to the split-screen display with the still

picture displayed on the right. In order to return to the normal display, press the FREEZE button

once again.

Swap

You can exchange the channel (or input) displayed in the split screen window for the main

screen image by pressing the SWAP button.

Note:

• It will only work in SPLIT mode.

Select

With SELECT, you can select the picture (channel) while viewing SPLIT screen. When you

press SELECT button, the channel number on the top will be highlighted. Each press of SELECT

will shift the channel.

The MENU button allows you to access JVC’s onscreen menu system. Press MENU to activate

the onscreen menu system.

• See individual topics like “Sound Adjust” for specific information on using menus.

This button confirms your selection when you are in one of the onscreen menus.

Back

This button allows you to go back in the menu to change a selection or correct a mistake.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Power

Turns the TV on or off.

Press the POWER button

Note:

• After turning the power on, you can not turn the power off for about one minute.

Number Buttons - 10Key Pad

Use the number buttons on the remote control to move directly to a specific channel. For

example, to move to channel 12:

0 (Zero)

1 (One)

2 (Two)

Tune

Lets you decide the input channel and select it. After you press the number buttons on the

remote, press the TUNE button. For example, to move to channel 12:

1 (One)

2 (Two)

Press the TUNE button

Input

Selects the signal input source for the television: VIDEO-1, 2, 3, 4, DIGITAL-IN1 or

DIGITAL-IN2 for video devices like VCRs, DVD players or camcorders.

Press the INPUT button

By every press of the INPUT button, you can change the input mode.

Notes:

• When you return to TV mode, press the RETURN +/TV button or direct 10 key pad or CHANNEL

+/– button.

• You can also access by pressing the INPUT button on the side of the TV instead of the remote

control.

• If you have a PC connected to the TV, select VIDEO-3.

TheaterPro D6500K

The TheaterPro D6500K color temperature technology function makes sure that the video you

watch is set to the standard color temperature, so that what you see is as true to what the film

to video editors intended it to be.

Press the THEATERPRO button

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Return +/TV

The RETURN+/TV button has three functions:

Return - Returns to the channel viewed just before the channel currently onscreen.

Return+ - Lets you program a specific channel to return to while scanning through the

channels using the CH+ and CH– buttons.

TV - Returns to the TV mode.

Press the RETURN+/TV and hold for three seconds

RETURN CHANNEL

PROGRAMMED!

The channel currently active has been programmed as your return+ channel. Now scan

through the channels using the CHANNEL+/– buttons.

Press the RETURN+/TV

You will return to your programmed channel.

• To cancel your return+ channel, press and hold the RETURN+ button for three seconds. The

message “RETURN CHANNEL CANCELLED!” will appear.

• Return+ works only with the Channel+/– buttons. Pressing any number key will cancel

return+.

Sound

By pressing the SOUND button, you can change the A.H.S.+ (Advanced Hyper Surround plus)

mode, A.T.C. (Advanced Tone Correction), SMART SOUND and MaxxBass on or off.

A.H.S.+ - Adds a more spacious surround sound. Music gives basic effect and movie for more

effect.

A.T.C. - Reproduces distinctive sounds with tone correction.

SMART SOUND - Decreases high sound levels, giving a regulated sound level.

MaxxBass - Emphasizes the bass sound.

SOUND EFFECT

Press the SOUND button

A.H.S.+

MOVIE MUSIC OFF

ON OFF

HIGH LOW OFF

π†

To select A.H.S.+, A.T.C., SMART SOUND or

MaxxBass

A.T.C.

SMART SOUND

MaxxBass

√®

To choose the setting

OPERATE

EXIT

SELECT

Press the MENU when finished

MaxxBass is a registered trademark of Waves Audio Ltd. in the USA, Japan and other

countries.

Notes:

• Smart Sound may become an unnatural effect, depending on the signal source.

• You can adjust BALANCE only when A.H.S.+ is off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Video Status

The VIDEO STATUS button gives you a choice of four TV picture display settings, including a

display of your own preferences.

Standard - Resets the picture display to the factory settings.

VIDEO STATUS

Dynamic - Gives a vivid picture with better contrast when

STANDARD

DYNAMIC

THEATER

GAME

viewing in a brightly lit room.

Theater - Gives a rich, film-like look to video when viewing in

a dimly lit room.

Game - Used for when you are playing video games

connected to your TV.

Press the VIDEO STATUS button

By every press of the VIDEO STATUS button, you change the mode.

Note:

• You can also change the mode by pressing the π† buttons.

• Each mode is memorized for each input connected to the TV.

• You can also access the FRONT CONTROL PANEL screen by using the MENU button on

the side of the TV instead of the remote control. It appears between INITIAL SETUP and

PICTURE ADJUST screen, and it has VIDEO STATUS and ASPECT menus. Choose VIDEO

STATUS by pressing MENU

+/- buttons ( OPERATE

†

on the side panel and choose a mode by using the CHANNEL

√

• There are four video status settings: Dynamic, Standard, Theater and Game. Each video

status setting has a separate memory for HD (1080i/720p) and SD (480p/480i) video signal.

Each video status can be chosen along with your favorite picture settings (Tint, Color,

Picture, Bright, Detail, etc.)

– When an HD signal is displayed: Your HD settings are recalled for the video status you

are using.

– When an SD signal is displayed: Your SD settings are recalled for the video status you

are using.

– This function considers PC input as an HD signal and PIP and SPLIT screens as an SD

signal.

Natural Cinema

Natural cinema corrects the problem of blurred edges which may occur when viewing a program

originally shot on film (such as motion pictures) or animation. If you notice blurring at the edges

of these programs, press NATURAL CINEMA and set it to AUTO. Natural Cinema helps correct

conversion errors that occur when film, which is shot at 24 frames-per-second, is broadcast at the

television rate of 30 frames-per-second.

Press the NATURAL CINEMA button

NATURAL CINEMA

AUTO

OFF

Notes:

• The natural cinema mode is automatically set to “AUTO” in

the following cases:

- Turning on or off

- Changing the channel or input mode

- Using multi-screen functions

• If you are in PC mode, Natural Cinema can not be used.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Sleep Timer

The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals

of 15 minutes, for a total time of up to 180 minutes.

Press the SLEEP button

0 15 30 45 60 75 90 105 120 135 150 165 180

Sleep Timer Message

60 seconds before the automatic shutoff, this message will appear:

GOOD NIGHT!!

PUSH SLEEP TIMER BUTTON

TO EXTEND

You then have 60 seconds to press the SLEEP button to

delay the shut off for another 15 minutes.

ML/MTS

MTS technology allows several audio signals to be broadcast in analog at once, giving you a

choice in what you wish to hear with a TV program. In addition to mono or stereo sound, an

MTS broadcast may also include a second audio program (SAP).

Press the ML/MTS button

MTS

ON AIR

By every press of the ML/MTS button, you change the

STEREO

mode

ON AIR

SAP

MONO

Notes:

• When you are receiving a digital broadcast, if there are other languages, you can change the

language by pressing the ML/MTS button.

• Keep the TV in stereo mode to get the best sound quality. The sound will work in stereo

mode even if a certain broadcast is in mono sound only.

• Choose the mono setting to reduce excessive noise on a certain channel or broadcast.

• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.

• MTS unavailable if your television’s Input source is in VIDEO-1, 2, 3, 4, DIGITAL-IN1 or

DIGITAL-IN2 mode, as described on page 64.

• ML/MTS will not work when you are using the Digital-In.

• You can also change the mode by pressing the π† buttons.

Muting

The MUTING button instantly turns the volume down completely when you press it. Press

MUTING and the volume level will instantly go to zero. To restore the volume to its previous

level, press MUTING again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Display

The display screen shows the current status of timers, inputs and XDS ID.

Press the DISPLAY button

The screen to the right shows the following

information:

05 KLVX PBS

JAZZ FESTIVAL

NOW

SLEEP TIMER

ON/OFF TIMER

ON TIME

• The current channel or AV input (Channel 05)

• The current time (12:20 pm)

• Sleep timer status/minutes remaining (The Sleep

Timer is off)

• On/off timer status (Set to turn on everyday at

7:00 PM, off at 10:00 PM)

12:20 PM

OFF

EVERYDAY

7:00 PM

OFF TIME

10:00 PM

• Each Press of the DISPLAY button changes the

display mode:

Display

Time

Channel

Off

Display - Full screen shown above

Time - Shows the current time only

Channel - Shows the current channel

Off - Turns display off

Notes:

• You may also turn off the display at any step by pressing MENU.

• If the clock, sleep timer or on/off timer are not set, the display screen will show:

“CLOCK NOT SET”, “SLEEP TIMER OFF”, and “ON/OFF TIMER OFF” respectively.

C.C. (Closed Caption)

Use the C.C. (Closed Caption) button to select the mode of closed caption.

Press the C.C. button

Notes:

• SMART CAPTION will appear when you press the MUTING

button, only on channels where the broadcast contains

closed captioning.

• When you select ON, it will be the mode selected in the

Closed Caption Menu.

CLOSED CAPTION

OFF

SMART CAPTION

• See page 45 when you set the caption/text mode.

• You can also change the mode by pressing the π† buttons.

• If you are in PC mode, C.C. can not be used.

Channel +/–

Use these buttons to move up or down all the available channels your TV is able to receive.

Volume +/–

Use these buttons to raise or lower the TV’s volume level. The maximum is the level you set in

Volume Limit. See page 58.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Favorite

The Favorite button allows you to select your favorite channels easily. First, you must register

the channels that you like. See how to register below.

Press the FAVORITE button

FAVORITE

The favorite channel list will appear.

π†

To select the channel you want to watch

101

102

D103

CBS

FOX

PBS2

Press the OK button

It will change to the channel you have selected.

D107

HBO

ABC

Press the channel number you want to register

The channel program will change.

Press the FAVORITE button for three seconds

The channel will be registered in the favorite channel list.

Notes:

• Both analog and digital channels can be registered. The digital channels have a "D" in front

of the channel number.

• The maximum number of channels you can register is 24.

• If you have registered the maximum number of channels, and try to register more channels,

the oldest channel you registered will be deleted.

• Sub channels can not be registered.

• The newest channel you registered will appear at the top of the list.

Delete the favorite channel

Press the FAVORITE button

The favorite channel list will appear.

π†

√®

To select the channel you want to delete

To enter

Press the OK button

The channel was deleted.

Press the FAVORITE button when finished

Note:

• Before pressing the FAVORITE button when you are finished, press the √® button again, and

you can return to the deleted channel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Aspect

This feature will help you adjust the picture you are watching to give you the best possible

picture quality.

Aspect Ratios

PANORAMA - With this ratio a normal

4:3 aspect picture is stretched to fit the

dimensions of the 16:9 aspect screen.

REGULAR - The regular ratio is used

when you want to watch a 4:3 broadcast

or recorded program without modifying the

original picture to fit the dimensions of your

16:9 screen. The 4:3 picture will fill the

screen from top to bottom, while black bars

will appear to fill up the remaining space

along the picture’s sides. The 4:3 picture

will be centered within the boundaries of the

16:9 screen.

CINEMA - This ratio “zooms in” on the

center part of a 4:3 aspect picture, blowing

it up to fill the 16:9 screen.

SLIM - This aspect mode shrinks the

screen of 16:9 to 4:3. There are some

programming that is already stretched by

mistake at broadcasting companies, so

this mode corrects it. Black side bars will

appear.

FULL - This is the ratio to use when

watching 16:9 High-Definition broadcasts.

PANORAMA ZOOM - This ratio stretches

the High-Definition 16:9 aspect image to

eliminate the black side bars.

Aspect Ratios in PC Mode

REGULAR - This is the original aspect

mode.

CINEMA ZOOM - This ratio stretches

the High-Definition 16:9 aspect image to

eliminate the black surrounding bars.

FULL - This aspect mode stretches the

image to fit the dimensions of the 16:9

aspect screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

Aspect Ratios (Continued)

Press the ASPECT button

• By pressing the ASPECT button, you can change the size.

When you change the aspect ratios, it is different from their broadcast or recorded program.

ATSC (480i, 480p)

SD (480i, 480p)

HD (1080i, 720p)

NTSC, 480i, 480p

ATSC (1080i, 720p)

ASPECT

PANORAMA ZOOM

CINEMA ZOOM

FULL

ASPECT

PANORAMA

CINEMA

ASPECT

PANORAMA ZOOM

CINEMA ZOOM

FULL

ASPECT

FULL

REGULAR

FULL

REGULAR

SLIM

Notes:

• You can also choose the size by pressing the π† buttons.

• When you change the aspect ratio or signal, reset the picture position to center.

• You can also access the FRONT PANEL CONTROL screen by using the MENU button

on the side of the TV instead of the remote control. It appears between INITIAL SETUP

and PICTURE ADJUST screen, and it has VIDEO STATUS and ASPECT menus. Choose

ASPECT by pressing Menu

+/- buttons ( OPERATE

†

on the side panel and choose a mode by using the CHANNEL

√

• "SLIM" can only be dispalyed when the signal is ATSC (480i or 480p).

• If the televison receives a 16:9 signal from your HDMI device, the aspect mode will turn to

FULL automatically. If the television receives a 4:3 signal from your HDMI device when you

are in FULL aspect mode, it will return to REGULAR aspect mode. If you change the aspect

mode after the televison changed it to FULL automatically, the televison will change to the

aspect mode you choosed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

TV/CATV Slide Switch

Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to

operate the television’s built-in tuner. Move the switch to CATV to operate a cable box.

Note:

• See page 27 for information on programming your remote for cable box operation.

VCR/DVD Slide Switch

You can control a VCR or DVD player with the buttons on the lower part of the remote control.

Move the slide switch to VCR or DVD to operate.

Notes:

• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other

manufacturer’s brand VCR, please see the code chart and instructions on page 28.

• The remote is preset with the code 000 to control JVC-brand DVD players. For any other

manufacturer’s brand DVD player, please see the code chart and instructions on page 29.

VCR Buttons

You can use this remote control to operate the basic functions of your VCR. These functions

include: play, record, rewind, fast-forward, stop, pause, channel scan, TV/VCR, power on and

power off.

Move the selector switch to VCR to operate.

• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other

manufacturer’s brand VCR, please see the code chart and instructions on page 28.

DVD Buttons

You can also use this remote control to operate the basic functions of your DVD player. These

functions include: play, rewind, fast-forward, stop, still/pause, previous/next, tray open/close,

power on and power off.

Move the selector switch to DVD to operate.

• The remote is preset with the code 000 to control JVC-brand DVD players. For any other

manufacturer’s brand DVD player, please see the code chart and instructions on page 29.

Light

Your remote control includes illuminated buttons for key features like CHANNEL +/- and

VOLUME +/-. Press the LIGHT button to turn the illumination on for 5 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

Button Functions

D/A (Digital/Analog)

The D/A button changes the analog and digital channel. Each time you press the D/A button,

you can switch back and forth the analog and digital channels. Digital channels have a "D" in

front of the channel number.

Press the D/A button

To watch digital channels

For example, to move to channel D23:

Press 2 (Two)

Press 3 (Three)

Press the TUNE button

Sub Channel

The main channel sometimes has minor channels (Sub Channels). By using the SUB CHANNEL

button, you can select a sub channel easily.

For example, to move to sub channel 123-45:

Press 1, 2 and 3 in order

Press the SUB CHANNEL button

Press 4 and 5 in order

Press the TUNE button

Note:

• If there are more than 2 major channels, select the digital channel by using the π† buttons

and then press the OK button.

Guide

You can view the program from the GUIDE.

Notes:

• The GUIDE function will only work when you are receiving digital programming only.

• The GUIDE will not show the correct time and date if you have not performed the set clock

function on your television. See page 59.

Download from Www.Somanuals.com. All Manuals Search And Download.

OSD Information

Weak Signal

This OSD warning appears when the digital channel that you have selected is too weak to

receive or no signal is being detected for that channel.

Weak Signal

No Program

If the TV channel you selected, or were watching is not receiving a signal, "NO PROGRAM"

appears on the television screen. It appears when that channel is not receiving a signal and you

have the Noise Muting function OFF and you have a single screen. It moves automatically every

two seconds to prevent the screen from burn-in.

Note:

• Even if "NO PROGRAM" appears on the screen, your timer functions and auto shut off

functions that you set, are still active.

Invalid Signal

If you are inputting a PC signal that is invalid, "Invalid Signal" will appear on the TV screen. It

appears when the input is PC and it is a single screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp Replacement

Changing the Lamp

WARNING!

It is very important that you NEVER TOUCH THE GLASS SURFACE OF THE NEW

LAMP. Touching the glass surface will deposit oils from your hand onto the lamp

surface. When the lamp heats up to its operating temperature, the oil will cause a

difference in temperature on the lamp surface that will likely cause the lamp to break.

Replace the lamp with part number TS-CL110U only! The television is designed

to work specifically with this lamp. Using a different lamp, or a third-party

manufacturer’s lamp could cause a malfunction and or damage to the television.

This television uses a 110-Watt high-pressure mercury lamp to project images onto the

television screen. When the lamp nears the end of its operating life, you may notice the picture

becoming dark. When the picture begins to darken, or the lamp burns out, it is time to replace

the lamp. The following instructions will tell you how to safely replace the lamp.

WARNING!

Under operating conditions, THE LAMP WILL GET EXTREMELY HOT AND WILL

CAUSE SEVERE BURNS IF TOUCHED.

Before attempting to replace the lamp, make sure the television has completely run

through its cooling cycle. Turn the power off and wait until the LAMP LED blinks very

slowly and turns off completely. Unplug the TV. If you feel any warmth as you place

your hand near the lamp, DO NOT TOUCH IT. Wait until the lamp has completely

cooled before attempting to replace it. After turning the power off, wait at least 1 hour

or more.

NEVER attempt to replace the lamp with the television plugged into a wall outlet.

Attempting to replace the lamp with the TV plugged in could lead to a severe electrical

shock.

Do not keep the TV on for more than 24 hours consecutively. There is the possibility

of the life of the lamp being shortened.

The life of the lamp changes depending on the atmospheric temperature and altitude

in which the TV is being used.

Please read these instructions fully before attempting to replace the lamp. If you feel

unsure about replacing the lamp yourself, call a service technician.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp Replacement

Replacement Lamp Kit

Before replacing the lamp, you will need to purchase a replacement kit, part number

TS-CL110U. To purchase this kit, consult your dealer or call 1-800-252-5722, or go to www.jvc.

com.

The replacement kit will include the following:

1 High-Pressure Mercury Lamp

1 Instruction Manual

Because the lamp contains a small amount of mercury, it cannot be disposed of with

normal trash.

Lamp Message

If this message appears when you turn the TV

on, you need to replace the lamp. See page 77

on how to replace the lamp.

LAMP NEEDS TO BE REPLACED.

REFER TO OWNER'S MANUAL FOR

REPLACEMENT INSTRUCTIONS.

Note:

AFTER REPLACING THE LAMP,

PLEASE RESET TIMER IN THE TV

MENU.

• This message will appear every time you

turn on the TV when the lamp needs to be

replaced. Press the OK button to make the

message disappear, or replace the lamp.

PRESS OK, IF YOU DO NOT WANT

TO SEE THIS MESSAGE AGAIN.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp Replacement

How to Replace the Lamp

Please read these instructions fully before attempting to replace the lamp. If you feel

unsure about replacing the lamp yourself, call a service technician. Please observe all

safety warnings.

1) Turn off the television.

Press the POWER button on the remote control or TV front panel. Wait until the picture has

closed and the LAMP LED on the front panel has stopped blinking indicating the lamp cool

down is complete.

Warning: The cool-down process cools the lamp from its operating temperature. This

does not mean that the lamp will now be cool enough to handle safely. We strongly

recommend you wait at least one hour before proceeding.

2) Unplug the television.

Disconnect the power cord from the AC outlet. Make sure that the LAMP LED light has stopped

blinking before you unplug the set. Never attempt to replace the lamp with the television

plugged in.

3) Remove the lamp cover.

The lamp is located behind the lamp cover below the left side of the

television. To access the lamp you will need to remove the lamp cover.

First, remove the screw located on the lamp cover using a Philips head

type screwdriver (cross-head type). Once the screw has been removed,

gently pull the knob towards you and the panel will come away from the

television. Set it aside.

WARNING: DO NOT attempt to remove the assembly until the lamp has fully cooled. If you

feel any heat near the lamp, STOP and wait until the lamp has FULLY COOLED.

NEVER attempt to remove the lamp with the television plugged into an outlet.

DO NOT DROP the used lamp. The inside of the lamp is under pressure. Dropping or other

hard shock could cause the lamp to shatter.

ALWAYS recycle the used lamp. Because the lamp contains a small amount of mercury, it

cannot be thrown away with regular trash. Follow the recycling instructions included with the

Lamp Replacement Kit.

4) Remove the lamp unit.

Using a Philips head type screwdriver (cross-head type), loosen the two screws fastening the

lamp unit. When the screws have been loosened, remove the lamp by raising the handle and

gently sliding the unit straight towards you. Place it carefully in the recycling packaging.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp Replacement

5) Install the new lamp unit.

Holding the handle attached to the new lamp unit, slide and push the new lamp straight into the

television and back into the lamp housing area. Do not forget to re-tighten the two screws.

Note: If the lamp does not sit securely in the TV (flat in the lamp housing area), it won’t turn on.

Make sure the lamp sits securely and flat in the housing area.

WARNING!

Remember it is very important that YOU DO NOT TOUCH THE LAMP SURFACE. Please

read the warnings on page 75 again.

Also, replace the lamp with part number TS-CL110U only! The television is designed

to work specifically with this lamp. Lamps other than TS-CL110U may cause

malfunctions and/or other damage to the television.

NOTICE (for USA)

This product has a High Intensity Discharge (HID) lamp that

contains a small amount of mercury. It also contains lead in some

components. Disposal of these materials may be regulated in your

community due to environmental considerations. For disposal or

recycling information, please contact your local authorities, or the

Electronics Industries Alliance: http://www.eiae.org

To purchase a replacement lamp kit, please call 1-800-252-5722.

6) Re-install the lamp cover.

Insert the lamp cover in the right concave and close the lamp cover. Because the lamp cover

has a role to help prevent the danger of an electrical shock, tighten the screw using your

fingers.

Note:

• After installing the new lamp unit, do not forget to reset the lamp timer. See page 61.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp Replacement

Warning LED Messages

While the power is on, and there is a problem with the TV, the TV changes to warning

mode and informs you of the problem using the LED as follows. Then, the power turns off

automatically and performs the cooling for approximately 90 seconds.

The LAMP LED blinks

Condition: It may be a malfunction of the internal electrical circuits.

To correct: Keep the TV off for a while and then turn the power on again. If the TV goes into

warning mode, unplug the TV after the cooling has completed and consult your

dealer.

The POWER LED and LAMP LED blink alternately

Condition: The inside temperature rises abnormally or the fan may be blocked.

To correct: Keep the TV off for a while and then turn the power on again. If the TV goes into

warning mode, unplug the TV after the cool down as completed and consult your

dealer.

The POWER LED and LAMP LED blink rapidly simultaneously

Condition: The lamp unit has been installed on a slant and is not flat, or it is not fully inserted

into the lamp housing. Or it may be a lamp malfunction.

To correct: • If this condition occurs soon after replacing the lamp: Reinstall the new lamp unit.

Repeat the lamp installation steps, taking care to observe all warnings. Make

sure the lamp sits FLAT inside the unit when you reinstall it.

• If this condition occurs except for replacing the lamp: Keep the TV off for a while

and then turn the power on again. If the TV goes into warning mode, unplug the

TV after the cool down as completed and consult your dealer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

PROBLEMS

CHECK

There is no power

• See if the power cord became unplugged.

• Check for a blown fuse or circuit breaker or a power outage.

•

It is possible the fan is stuck or the inside temperature is rising abnormally.

Consult your dealer.

There is no picture

or sound

• The antenna could be disconnected.

• The input mode could be set improperly. See page 64.

• The tuner (Auto Tuner Setup) could be set improperly. See page 34.

• The TV station may be having difficulties. Check to see if other stations are working.

• Use the HDMI cable with HDMI logo

. See page 20.

• You can not output audio using the AUDIO OUTPUT under the following conditions:

1) When you have digital sound from an HDMI device connected to the HDMI 1 or

HDMI 2 connection on the back of your TV. (See page 20).

2) When you have analog sound from a DVI device connected to the

AUDIO IN "HDMI 1" connection. (See page 19).

• When you have an HDMI device connected to the HDMI 1 connection on the back of your

TV, your TV detects it, and blocks the analog audio signal coming into the "HDMI 1”

jacks. Therefore, you can not hear any analog sound from the other device conected to the

"HDMI 1" jacks, while you are viewing the images from the HDMI device.

(See page 20).

Remote control is not • Check to see that the batteries are still working and properly installed.

operating properly or • Make sure the remote has a clear sight path to the TV.

at all

• Check that the TV/CATV switch is in the proper position.

• You may be too far from the TV. You must be within 23 feet (7 meters).

You cannot select a

certain channel

• Make sure the channels have been programmed. See "Channel Summary", page 35.

• Check to see if the channel is locked. See "Channel Summary - Lock" page 36.

The power turns off

by itself

• Make sure the set did not become unplugged.

• Perhaps the On/Off Timer is set. See page 60.

• Check to see if the Sleep Timer was set. See page 67.

It does not operate

correctly

• This television is operated by a microprocessor. It is possible that external noise or

interference is causing the problem. If the television does not function correctly, remove the

electrical plug from the wall outlet and wait a while before inserting it into the wall outlet

again and operating the television.

The clock is wrong

• The power was interrupted and the clock was not reset. See page 59.

The color quality

is poor

• Tint and Color may be improperly adjusted. See page 55.

• The Video Status mode may be turned to the wrong setting. See page 66.

There are lines

across the picture

• There could be interference from another electrical appliance, such as a computer,

another TV or VCR. Move any such appliances further away from the TV.

• There could be interference from a high-wattage appliance, like a hairdryer or vacuum,

operating nearby. Move the antenna away from the appliance or change to a coaxial

cable connection which is less prone to interference.

The picture is spotted

There are double

pictures (ghosts)

• A building or passing airplane can reflect the original signal and produce a second,

slightly delayed one. Adjust your antenna position.

Picture is snowy

(image noise)

• Your antenna may be damaged, disconnected or turned. Check the antenna

connection. If the antenna is damaged, replace it.

Screen is 80% black

• The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 45.

• Make sure the MTS settings are correct. See page 67.

Stereo or bilingual

programs can't be

heard

The POWER LED

and LAMP LED are

blinking

•

It may be a malfunction that the fan is locked or the temperature has increased.

alternately.

The POWER LED

and LAMP LED are

blinking rapidly

• The lamp may not have been installed correctly, or it may be due to a malfunction.

• The lamp door may not be closed correctly.

simultaneously.

The LAMP LED

continues blinking

• It may be a malfunction of the internal electrical circuits.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

PROBLEMS

CHECK

Static electricity

• It is normal to feel static electricity if you brush or touch the screen.

You hear occasional

crackling sounds

• It is normal for the TV to make crackling sounds when first turned on or off. Unless

the sound or picture become abnormal, this is fine.

The following are not malfunctions.

• The television may make a creaking sound if the temperature of the room or the temperature

inside the television changes. If there is no problem with the screen or sound, then there is no

need to worry.

• The lamp may make a noise when it blows, but this is not dangerous.

• The lamp may make a noise when the power is turned on and a picture is displayed on

the screen. This noise is caused when the mercury inside the lamp is heated, and is not a

malfunction.

• The still parts of a picture may remain on the screen. This is a characteristic of HD-ILA

elements and not a malfunction. The picture will disappear over time.

• The operation of this television is not guaranteed below 0ºC. If the power is turned on while

the temperature is below 0ºC, the picture may be disturbed. Use the television when the

temperature is 0ºC or higher.

• Although the HD-ILA element is manufactured with high-precision technology, please

understand that some pixels may be lost or permanently displayed.

• There is a cooling fan built-in to the television. Please understand that this fan will make some

noise when the television is on and while cooling.

• Although the picture may be temporarily disturbed and noise may be seen on the screen if the

power is turned on immediately after it has been turned off. This is not a malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

HD-52G887

Model

HD-56G887

HD-56G787

HD-52G787

Type

HD-ILA Device Projection

NTSC, BTSC System (Multi-Channel Sound)

ATSC Terrestrial, Digital Cable

Reception Format

VHF 2 to 13, UHF 14 to 69 at ATSC,

CATV 135 Sub, Mid, Super, Hyper and Ultra bands at Digital Cable

Reception Range

VHF 2 to 13, UHF 14 to 69 CATV 125 Sub, Mid, Super, Hyper

and Ultra bands (181 channel frequency synthesizer system) at Analog

•

Reception of channel A-5 ("95" of the TV set's on-screen cable channel

numbers) is not recommended for your TV set.

Power Source

Power Consumption

Projection Source

AC 120V, 60 Hz

205W

110W High-Pressure Mercury Lamp

52 inch / 132 cm

measured diagonally,

16:9 ratio

56 inch / 142.2 cm

measured diagonally,

16:9 ratio

Screen Size

Speakers

10 cm round X 2

Audio Output

Full Range - 10W + 10W

Antenna Terminal

(VHF/UHF,

ATSC/DIGITAL

CABLE IN)

75 ohms (VHF/UHF)(F-type connector)

S (Input 1, 3)

Input 1, 2, 3, 4

Terminal

Y: 1 Vp-p positive, 75 ohms (negative sync provided)

C: 0.286 Vp-p (burst signal), 75 ohms

Video: 1 Vp-p, 75 ohms

Audio: 500 mVrms (-4dBs) high impedance

Input 1, 2 Terminal

(component terminal)

1080i / 720p / 480p / 480i

Y: 1 Vp-p positive, 75 ohms (negative sync provided)

Pb/Pr: 0.7 Vp-p 75 ohms

HDMI Jack x 2

DIGITAL-IN

(HDMI input terminal)

•

Personal computer compatibility cannot be guaranteed.

Video: 1080i / 720p / 480p / 480i / VGA

Audio: 2ch PCM, 32 / 44.1 / 48 KHz 16 / 20 / 24 bit

Audio Output Jacks

(FIX)

FIX : 500mVrms (-4dBs) Low impedance (1000 Hz when modulated 100%)

Digital Out (optical) x 1

Optical Output

Digital Audio

Analog RGB D-SUB (15 pin) x 1

• PC signal is available. Refer to page 23 for details on the signals which

can be input.

PC Input Jack

Dimensions (inch)

W X H X D (cm)

48 1/2 x 35 7/8 x 16 3/8

122.9 x 91.1 x 41.5

52 x 38 1/8 x 17 3/8

131.8 x 96.8 x 43.9

Weight (lbs / kg)

84 / 38

90 / 41

Accessories

Remote control unit x 1 / AA batteries X 2

Specifications subject to change without notice.

• The open source software is embedded in this product. For more information, please go to:

http://software.jvc.com/opensource/lnx/DP/05_AtscQam/download.html

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

HD-61G887

HD-61G787

Model

HD-70G887

Type

HD-ILA Device Projection

NTSC, BTSC System (Multi-Channel Sound)

ATSC Terrestrial, Digital Cable

Reception Format

Reception Range

VHF 2 to 13, UHF 14 to 69 at ATSC,

CATV 135 Sub, Mid, Super, Hyper and Ultra bands at Digital Cable

VHF 2 to 13, UHF 14 to 69 CATV 125 Sub, Mid, Super, Hyper

and Ultra bands (181 channel frequency synthesizer system) at Analog

•

Reception of channel A-5 ("95" of the TV set's on-screen cable channel

numbers) is not recommended for your TV set.

Power Source

Power Consumption

Projection Source

AC 120V, 60 Hz

205W

110W High-Pressure Mercury Lamp

61 inch / 154.9 cm

measured diagonally,

16:9 ratio

70 inch / 177.8 cm

measured diagonally,

16:9 ratio

Screen Size

Speakers

10 cm round X 2

Audio Output

Full Range - 10W + 10W

Antenna Terminal

(VHF/UHF,

ATSC/DIGITAL

CABLE IN)

75 ohms (VHF/UHF)(F-type connector)

S (Input 1, 3)

Input 1, 2, 3, 4

Terminal

Y: 1 Vp-p positive, 75 ohms (negative sync provided)

C: 0.286 Vp-p (burst signal), 75 ohms

Video: 1 Vp-p, 75 ohms

Audio: 500 mVrms (-4dBs) high impedance

Input 1, 2 Terminal

(component terminal)

1080i / 720p / 480p / 480i

Y: 1 Vp-p positive, 75 ohms (negative sync provided)

Pb/Pr: 0.7 Vp-p 75 ohms

HDMI Jack x 2

DIGITAL-IN

(HDMI input terminal)

•

Personal computer compatibility cannot be guaranteed.

Video: 1080i / 720p / 480p / 480i / VGA

Audio: 2ch PCM, 32 / 44.1 / 48 KHz 16 / 20 / 24 bit

Audio Output Jacks

(FIX)

FIX : 500mVrms (-4dBs) Low impedance (1000 Hz when modulated 100%)

Digital Out (optical) x 1

Optical Output

Digital Audio

Analog RGB D-SUB (15 pin) x 1

• PC signal is available. Refer to page 23 for details on the signals which

can be input.

PC Input Jack

Dimensions (inch)

W X H X D (cm)

57 3/8 x 41 1/8 x 18 5/8

145.6 x 104.2 x 47

64 1/8 x 46 x 20 1/2

162.6 x 116.7 x 51.9

Weight (lbs / kg)

95 / 43

154 / 70

Accessories

Remote control unit x 1 / AA batteries X 2

Specifications subject to change without notice.

• The open source software is embedded in this product. For more information, please go to:

http://software.jvc.com/opensource/lnx/DP/05_AtscQam/download.html

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

Download from Www.Somanuals.com. All Manuals Search And Download.

JVC COMPANY OF AMERICA

Division of JVC Americas Corp.

1700 Valley Road

JVC CANADA, INC.

21 Finchdene Square

Scarborough, Ontario

Canada, M1X 1A7

Wayne, New Jersey, 07470

Download from Www.Somanuals.com. All Manuals Search And Download.

Ironman Fitness Home Gym Adventure User Manual
JAMO Portable Speaker 892A2 User Manual
JAMO Speaker D 4 User Manual
Jenn Air Dishwasher W10418360A User Manual
Karcher Washer Dryer K5800G User Manual
Kawai Musical Instrument ES3 User Manual
Kenmore Microwave Oven 7217915 User Manual
Kenmore Vacuum Cleaner 11632734 User Manual
Kenwood Cassette Player KRC 160 User Manual
Kenwood CD Player 76 User Manual