K5800G Manual 11/30/01 5:02 PM Page 1
Model K 5800 G
Part No. 1.194-103.0
High Pressure Washer Operator Manual
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . .3
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . .4
Using the Accessories . . . . . . . . . . . . . . . . . . . . . . . .5
Working with Detergents . . . . . . . . . . . . . . . . . . . . . . .6
Shut Down and Clean-Up . . . . . . . . . . . . . . . . . . . . . .7
Taking a Break . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Winterizing and Long-Term Storage . . . . . . . . . . . . . .7
Cleaning Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
Optional Cleaning Accessories . . . . . . . . . . . . . . . . . .9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Specifications
Operating pressure 2300 PSI
Water volume
Engine
2.5 GPM
5.0 HP Honda
Download from Www.Somanuals.com. All Manuals Search And Download.
K5800G Manual 11/30/01 5:02 PM Page 4
ASSEMBLY INSTRUCTIONS
OPERATING INSTRUCTIONS
Required tools: adjustable pliers.
Step1 Tilt machine backwards slightly
(caution: oil may leak if tilted too far).
Attach the front guard to the frame. Align
holes, insert bolt and tighten with lock nut.
Step2 Attach the handle to the frame of
the pressure washer. Align holes, insert bolt,
and tighten with knob.
Step1 Connect the high pressure hose
Step2 Connect garden hose to unit’s
to the unit’s high pressure outlet.
water inlet.
3
4
Step3 Connect garden hose to the cold
Step4 Trigger the gun to eliminate
trapped air, wait for a steady flow of water
to emerge from the spray nozzle.
water source and turn water on completely.
Step3 Attach the triple jet nozzle to the
Step4 Attach the spray wand to the
spray wand.
trigger gun.
Step5 Check oil level. Oil level should be
to the oil filler neck. Be sure the machine is
level when checking the oil level. (Refer to the
engine’s operating manual for seasonal grades.)
Step6 Fill gas tank with unleaded
gasoline. Do not use leaded gasoline.
Important! Do not run the engine
with a high or low oil level as this can
cause engine damage. If you have fur-
ther questions regarding the engine,
please refer to the engine’s operating
manual included with the unit.
Step5 Slide the throttle control to the
fast position. Move the choke lever to the
“CHOKE” position (only if the engine is cool).
After starting, move the choke to “RUN”.
Step6 Pull the starter handle. If the
engine fails to start after 3 pulls squeeze the
trigger gun to release pressure, and repeat
step 6.
Download from Www.Somanuals.com. All Manuals Search And Download.
K5800G Manual 11/30/01 5:02 PM Page 6
USING THE ACCESSORIES
WORKING WITH DETERGENT
The triple jet nozzle must be positioned to one of the two settings for high pressure cleaning
by turning the the nozzle tip. The pencil jet spray (0º) should be used for stubborn dirt. The
High pressure flat spray (25º) should be used for cleaning over a large surface area. The third
setting on the triple jet nozzle is used for the application of detergents.
Detergents can only be applied in the “CHEM” setting.
High pressure
pencil jet cleaning.
For best results see Cleaning
Tips on pages 8 & 9 for specific
information on how to clean
different surfaces.
Always Use Karcher
Detergents for Best Results.
Karcher biodegradable detergents are
specially formulated to protect the environ-
ment and your pressure washer. Special
formula won’t clog the suction tube filter
and will protect the internal parts of the
pressure washer for a longer life. For
Karcher Detergents, check your retailer
or call:
Step1 To apply detergents the triple jet
nozzle must be set to the “CHEM” position.
High pressure
fan spray cleaning.
5
6
1-800-537-4129
The following Karcher detergents are
available:
• Vehicle Wash
• Degreaser
• All Purpose Cleaner
• House Wash
• Deck Wash
Step2 Fill a container with Karcher
detergent. Place the filter end of detergent
suction tube into the container.
Low Pressure
Detergent application
“CHEM” position.
Caution
Never use:
• Bleach, Chlorine products and other
corrosive chemicals
• Liquids containing solvents
(i.e., paint thinners, gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
Step3 With the engine running, pull
trigger to operate unit: Liquid detergent is
drawn into the unit and mixed with water.
Apply detergent to work area. Do not allow
detergent to dry on surface.
WARNING TO AVOID
SERIOUS INJURY, NEVER
POINT SPRAY NOZZLE AT
YOURSELF, OTHER PERSONS
OR ANIMALS
Download from Www.Somanuals.com. All Manuals Search And Download.
K5800G Manual 11/30/01 5:02 PM Page 8
SHUTTING DOWN & CLEAN-UP
CLEANING TIPS
Cement Patios,
Deck Cleaning
Brick and Stone
(with or without detergent)
(with or without detergent)
Pre-rinse deck and surrounding area with
fresh water. If using Kärcher Deck Wash,
place detergent suction tube directly into
cleaning solution and apply to surface at
low pressure. For best results, limit your
work area to smaller sections of approxi-
mately 25 square feet. Allow Kärcher Deck
Wash to remain on surface 1-3 minutes. Do
not allow detergent to dry on surface. Rinse
at high pressure in a long sweeping motion
keeping the spray nozzle approximately 6
inches from the cleaning surface. Always
clean from top to bottom and from left to
right. When moving on to a new section of
the cleaning surface, be sure to overlap the
previous section to eliminate stop marks
and ensure a more even cleaning result.
Pre-rinse cleaning surface with fresh water.
If using Karcher All Purpose Cleaner, place
detergent suction tube directly into cleaning
solution and apply to surface at low pres-
sure. For best results, limit your work area
to smaller sections of approximately 25
square feet. Allow Kärcher All Purpose
Cleaner to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface.
Rinse at high pressure in a sweeping
motion keeping the spray nozzle approxi-
mately 3-6 inches from the cleaning sur-
face. Always clean from top to bottom and
from left to right.
Step1 Remove
Step2
Step3
Step4
detergent suction tube
from container and insert
into one gallon of fresh
water. Siphon water at low
pressure for one minute.
Turn off the engine.
Turn off the
water source.
Press trigger to
release water
pressure.
Cars, Boats & Motorcycles
(with or without detergent)
Pre-rinse vehicle with fresh water. If using
Karcher Vehicle Wash, place detergent suc-
tion tube directly into cleaning solution and
apply to surface at low pressure. For best
results, clean one side of vehicle at a time
and always apply detergent from bottom to
top, do not allow detergent to dry on sur-
face. Rinse at high pressure in a sweeping
motion keeping the spray nozzle approxi-
mately 8 inches from the cleaning surface
(distance should increase when rinsing pin-
striping or other sensitive surfaces). Always
clean from top to bottom and from left to
right. For best results, wipe surface dry with
a chamois or soft dry cloth.
House Siding
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Kärcher House Wash, place deter-
gent suction tube directly into cleaning
solution and apply to surface at low pres-
sure (for best results, limit your work area
to sections of approximately 6 feet and
always apply detergent from bottom to top).
Allow Karcher House Wash to remain on
surface 1-3 minutes. Do not allow detergent
to dry on surface, if surface appears to be
drying, simply wet down surface with fresh
water. Rinse at high pressure from top to
bottom in an even sweeping motion keep-
ing the spray nozzle approximately 6 inches
from the cleaning surface.
7
8
Step5 Disconnect
the garden hose from the
water inlet on the unit.
Step6 Disconnect the high pressure hose from the
high pressure outlet and engage the gun safety lock.
TAKING A BREAK... five minutes or more
Step1 Turn off the
Step2 Press trigger
Step3 Engage gun
engine.
to release water pressure.
safety lock.
WINTERIZING AND LONG-TERM STORAGE
1. Disconnect all water connections.
2. Start the machine for a few seconds,
until the water which had remained in the
pump exits. Turn off immediately.
3. Drain the gas and oil from the engine.
4. Do not allow high pressure hose to
become kinked.
5. Store the machine and accessories in
a room which does not reach freezing
temperatures. The machine should not be
placed near an open flame i.e. furnace,
hot water heater etc.
Caution: Failure to follow the above direc-
tions will result in damage to the pump
assembly and accessories.
Download from Www.Somanuals.com. All Manuals Search And Download.
K5800G Manual 11/30/01 5:02 PM Page 10
CLEANING TIPS - continued
TROUBLESHOOTING
Barbecue Grills, Outdoor
Power Equipment &
Recommendations
Symptom
Cause
Solution
Fill gas tank.
Add oil.
• Before cleaning any surface an inconspic-
uous area should be cleaned to test spray
pattern and distance for maximum clean-
ing results.
Engine will not
start
No gasoline.
Low oil level.
Gardening Tools
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Kärcher All Purpose Cleaner or
Degreaser, place detergent suction tube
directly into cleaning solution and apply
detergent at low pressure. Allow Kärcher
detergent to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface.
Rinse at high pressure keeping the spray
nozzle approximately 6 inches from the
cleaning surface. For removing extremely
stubborn dirt, it may be necessary to move
the spray nozzle even closer to the surface
for greater dirt cutting action.
• If painted surfaces are pealing or chipping,
use extreme caution as pressure washer
may remove the loose paint from the
surface.
Slide choke lever to “CHOKE”
position.
Choke is not in correct
position.
Engine throttle is not in
correct position.
Position the throttle to “FAST”.
For additional
Use extreme caution when cleaning decks,
siding, and other sensitive surfaces as the
pencil jet may cause damage if not used
correctly.
engine problems
refer to the engine
owners manual.
Pressure built up in the
high pressure washer.
Squeeze the trigger to release the
pressure.
Unit does not reach Diameter of garden hose is
Replace with a 3/4 inch garden
hose.
high pressure.
too small.
Water supply is restricted.
Check garden hose for kinks, leaks
and blockage.
Patio & Lawn Furniture
(with or without detergent)
Not enough inlet water supply. Open water source full force.
Pre-rinse furniture and surrounding area with
fresh water. If using Kärcher All Purpose
Cleaner, place detergent suction tube direct-
Water inlet filter is clogged.
Remove filter and rinse out in warm
water.
9
10
ly into cleaning solution and apply to surface
at low pressure. Allow Kärcher All Purpose
Cleaner to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface.
Rinse at high pressure in a sweeping motion
keeping the spray nozzle approximately 6
inches from the cleaning surface. For best
results, clean from top to bottom and from
left to right.
Nozzle is in “CHEM”
position.
Turn nozzle to high pressure position.
Output pressure
varies high and low.
Not enough inlet water supply. Turn water on full force. Check garden
hose for kinks, leaks or blockage.
Pump is sucking air.
Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing trigger gun until
a steady flow of water emerges
through the nozzle.
OPTIONAL CLEANING ACCESSORIES
Water inlet filter is clogged.
Remove filter and rinse out in warm
water.
Optional cleaning accessories are available to further enhance your cleaning capabilities.
Call Kärcher customer service hotline (1-800-537-4129) for details.
Discharge nozzle is
obstructed.
Blow out or remove debris with a
fine needle.
Calcified gun, hose or spray Run distilled vinegar through
wand. detergent suction tube.
Download from Www.Somanuals.com. All Manuals Search And Download.
K5800G Manual 11/30/01 5:02 PM Page 12
TROUBLESHOOTING - continued
Symptom
Cause
Solution
No detergent.
Detergent suction tube not
properly connected to the
machine.
Check connection.
Detergent is too thick.
Dilute detergent, for best results use
Kärcher detergent.
Filter on detergent suction
tube is clogged.
Run warm water through filter to
remove debris.
Damaged or clogged
detergent suction tube.
Remove obstruction or replace
detergent suction tube.
Spray nozzle is in high
pressure position.
Turn spray nozzle tip to ”CHEM”
position.
Discharge nozzle is
obstructed.
Blow out or remove debris with a
fine needle.
Garden hose
connection leaks.
Loose fitting.
Tighten fittings.
Missing/worn rubber washer. Insert new washer.
Tighten connections
Nozzle or spray wand not
properly attached.
Triple jet nozzle or
Spray wand leaks.
11
Call Kärcher customer service
hotline and order o”-ring.
Broken “o”-ring.
Pump is noisy.
Pump is sucking air.
Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing trigger gun until
a steady flow of water emerges
through the nozzle.
Water leaks from
pump (up to 10
drops per minute
is permissible).
Loose fittings.
Check that all fittings are tight.
Thermal protection device
has been activated.
Thermal protection device will
automatically reset.
Water seals are damaged
or worn.
Call service center.
Oil Drip.
Oil seals are damaged or
worn.
Call service center.
If you encounter any additional
difficulties not listed, please call
our service center for help.
Karcher Customer Support USA
1-800-537-4129
Download from Www.Somanuals.com. All Manuals Search And Download.
|