SPEAKER PLACEMENT
™
Proper placement of the
optimum placement of the
loudspeakers. Use these
placement recommendations
as a guide. Slight variations
will not diminish your listening
pleasure. All of the Studio
L
speakers is an important step
in obtaining the most realistic
soundstage possible. These
recommendations are for the
Series loudspeakers referred
to in this guide are video-
shielded and may safely be
placed near a television.
MODEL: L810
As front speakers
As surround speakers
5–6 ft.
(1.5m–1.8m)
MODEL: L820
The L820 loudspeakers are
designed to be oriented hori-
zontally, as shown in the illus-
trations below. Although these
loudspeakers are designed as
a mirrored pair, the decision
as to which one is left or right
will depend on the amount of
space left between them.
A wider stereo image is
For stereo-only applications:
presented with the tweeter/
midrange array outboard, and
a tighter image is presented
with the array inboard.
Less than 6–8 feet
(1.8m–2.4m)
More than 6–8 feet
(1.8m–2.4m)
For home theater applications:
0–2 ft.
(0–0.6m
This placement provides a
wide spread in sound, supple-
mented by the center channel
speaker.
MODEL: LC2
The LC2 center channel loudspeaker
is designed to complement all of the
Studio L Series loudspeakers. This
speaker is ideal for re-creating the
cinematic experience in your home.
®
STUDIO™ L SERIES
L810, L820, LC2
OWNER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
WALL-MOUNTING
Important Safety Notes
Model
Distance Between
Pilot Holes
tions for the pilot holes. Install
the loudspeaker by slowly
moving the cabinet toward
the screws so that the screw-
heads clear the larger circu-
lar portion of the two key-
holes. Once both screwheads
have entered the keyholes,
the loudspeaker should gently
be lowered onto the screw
shafts. Check that the loud-
speaker is firmly locked onto
the screws by gently pulling the
speaker down and forward.
• Proper selection of mount-
ing hardware and installation
of the wall brackets are the
responsibility of the customer.
L810
L820
LC2
6" (152mm)
8-1/2" (216mm)
14-1/2" (368mm)
• This product is not intended
for ceiling mounting.
See Figure 1. The holes
should be 2-1/4" (57mm)
Two Number 8 roundhead or
panhead screws should be
used for each loudspeaker.
The screwhead should be
between 5/16" (8mm) and 1/4"
(6.3mm) in diameter, and the
screw should be at least 2"
(50mm) in length.
below where you want the
top of the enclosure to be
positioned. Use a carpenter’s
level to ensure that the holes
are even and that the speaker
will mount on the level.
Install the two screws into
either a wooden wall stud or
anchor, and tighten them until
the back of each screwhead
is about 1/8" (3mm) from the
wall. See Figure 2.
Fig. 1
Fig. 2
When installing screws in any
wall, it is always preferable to
screw them into a wall stud. If
none is available, it is impor-
tant to always use properly
selected wall anchors.
See Chart
1/8"
(3mm)
Models L810 and L820 may
also be corner-mounted using
the keyholes located on the
bezeled corners. For corner
mounting, fold the mounting
template in half, place the
fold in the corner at the
desired height, and use the
outer holes. If the template is
missing, for corner mounting
drill each pilot hole 7-3/4"
(197mm) from the corner for
model L810, or 9-11/16"
(246mm) from the corner for
model L820. However, if your
corner is not precisely 90
degrees, these measure-
ments may not work. In that
case, it is recommended that
you contact a professional
custom installer, who can
determine the correct loca-
Attach two of the four self-
adhesive rubber pads that
came with the loudspeaker to
the back of the enclosure in
the two bottom corners so
that the cabinet is spaced
evenly from the wall. Select a
suitable mounting location on
a wall. (The ceiling is not a
suitable mounting location.)
Drill two pilot holes, appropri-
ately sized for the specific
self-tapping screw or wall
anchor that you will be using.
A template is included with
your loudspeaker that indi-
cates the proper locations for
the pilot holes. In the event
that the template is missing,
refer to this chart:
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
L810
L820
LC2
Description
3-Way, 5-1/4" Bookshelf/
Wall-Mount Satellite
4-Way, 6" High-Performance,
Mirror-Image,
Wall-Mount Satellite
4-Way, Dual 6"
Wall-Mount Center
Maximum
Recommended
Amplifier Power*
150W
150W
150W
Power Handling
(Continuous/Peak)
75W/300W
75W/300W
75W/300W
Nominal Impedance
Sensitivity (2.83V/1m)
8 Ohms
8 Ohms
8 Ohms
88dB
90dB
92dB
Frequency
Response ( 3dB)
60Hz – 40kHz
55Hz – 40kHz
50Hz – 40kHz
Crossover
Frequencies
3500Hz, 20kHz
600Hz, 3500Hz, 20kHz
700Hz, 4kHz, 20kHz
®
Ultrahigh-Frequency
High-Frequency
3/4" Mylar Dome With Cast-Aluminum Chassis
1" Pure-Titanium Dome With Cast-Aluminum Chassis in JBL EOS™ Waveguide
Midrange Transducer
N/A
4" PolyPlas™ Cone
With Rubber Surround
and Cast-Aluminum
Chassis; HeatScape™
Motor Structure
4" PolyPlas™ Cone
With Rubber Surround
and Cast-Aluminum
Chassis; HeatScape™
Motor Structure
Low-Frequency
Transducer(s)
5-1/4" PolyPlas™ Cone
With Rubber Surround
and Cast-Aluminum
Chassis; HeatScape™
Motor Structure;
6" PolyPlas™ Cone
With Rubber Surround
and Cast-Aluminum
Chassis; HeatScape™
Motor Structure;
Dual 6" PolyPlas™ Cones
With Rubber Surrounds
and Cast-Aluminum
Chassis; HeatScape™
Motor Structures;
Symmetrical Field
Symmetrical Field
Symmetrical Field
Geometry™ (SFG™);
Geometry™ (SFG™);
Geometry™ (SFG™);
®
®
®
Oversized Kapton
Oversized Kapton
Oversized Kapton
Voice Coil; Magnetic
Shorting Ring
Voice Coil; Magnetic
Shorting Ring
Voice Coils; Magnetic
Shorting Rings
Magnetic Shielding
Baffle
Yes
Yes
Yes
Low Diffraction, IsoPower™
Sealed
Enclosure
Bass-Reflex With
Dual FreeFlow™
Front-Firing Ports
Sealed
Straight-Line Signal Path™ (SSP
)
™
Network
Terminals
Gold-Plated 5-Way Binding Posts, Bi-Wirable
12-1/4" x 15-1/2" x 5"
Dimensions (H x W x D) 14-1/4" x 12-1/4" x 5"
(362mm x 311mm x 127mm)
12-1/4" x 22" x 5"
(311mm x 559mm x 127mm)
(311mm x 391mm x 127mm)
Weight per Speaker
14 lb (6.4kg)
19 lb (8.6kg)
29 lb (13.2kg)
*
The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks.
We do not recommend sustained operation at these maximum power levels.
All features and specifications are subject to change without notice.
All dimensions include grilles and feet, but not spikes.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If there is no sound from
any of the speakers:
• Check that receiver/ampli-
fier is on and that a source is
playing.
• Review proper operation of
your receiver/amplifier.
If there is no sound
coming from one
If there is no sound from
the surround speakers:
• Check all wires and con-
nections between receiver/
amplifier and speakers.
Make sure all wires are con-
nected. Make sure none of
the speaker wires are frayed,
cut, punctured or touching
each other.
• Review proper operation of
your receiver/amplifier and
its surround sound features.
• Make sure the movie or TV
show you are watching is
recorded in a surround
sound mode. If it is not,
check to see whether your
receiver/amplifier has other
surround modes you may
use.
• In Dolby Digital or DTS
modes, make sure your
receiver/processor is config-
ured so that the surround
speakers are enabled.
• Review the operation of your
DVD player and the jacket of
your DVD to make sure that
the DVD features the desired
Dolby Digital or DTS mode,
and that you have properly
selected that mode using both
the DVD player’s menu and the
DVD’s menu.
nel, the source of the prob-
lem is most likely with your
receiver or amplifier, and you
should consult the owner’s
manual for that product for
further information. If the
problem has followed the
speaker, consult your dealer
for further assistance or, if
that is not possible, visit
information.
speaker:
• Check the “Balance”
control on your receiver/
amplifier.
• Check all wires and con-
nections between receiver/
amplifier and speakers.
• Make sure no wires are
touching other wires or
terminals and creating a
short circuit.
If the system plays at
low volumes but shuts
off as volume is
increased:
• Check all wires and con-
nections between receiver/
amplifier and speakers.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
• If more than one pair of
main speakers is being used,
check the minimum imped-
ance requirements of your
receiver/amplifier.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
®
®
• In Dolby Digital or DTS
modes, make sure that the
receiver/processor is config-
ured so that the speaker in
question is enabled.
If there is no (or low)
bass output:
• Turn off all electronics and
switch the speaker in ques-
tion with one of the other
speakers that is working cor-
rectly. Turn everything back
on, and determine whether
the problem has followed the
speakers, or has remained
in the same channel. If the
problem is in the same chan-
• Make sure the polarities
(+ and –) of the left and right
“Speaker Inputs” are
connected properly.
• Consider adding a powered
subwoofer to your system for
use with digital “.1” surround
formats.
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Chateau du Loir
France
declare in own responsibility that the products described in this owner’s manual
are in compliance with technical standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Laurent Rault
Harman Consumer Group International
Chateau du Loir, France 8/05
JBL and Harman International are trademarks of Harman
International Industries, Incorporated, registered in the United
States and/or other countries.
™
PRO SOUND COMES HOME
Studio Series, Pro Sound Comes Home, EOS, PolyPlas, HeatScape,
Symmetrical Field Geometry (SFG), IsoPower, FreeFlow and
Straight-Line Signal Path (SSP) are trademarks of Harman
International Industries, Incorporated.
JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797 USA
8500 Balboa Boulevard, Northridge, CA 91329 USA
2, route de Tours, 72500 Chateau du Loir, France
Dolby is a registered trademark of Dolby Laboratories.
DTS is a registered trademark of DTS, Inc.
© 2005 Harman International Industries, Incorporated. All rights reserved.
Part No. 353334-001
Mylar and Kapton are registered trademarks of E.I. du Pont de
Nemours and Company
.
Download from Www.Somanuals.com. All Manuals Search And Download.
|