NETWORK PACK
User’s Guide
KA-DV5000
ACK
KA-DV5000
NETWORK
P
POWER
SUPPL
Y
O
N
O
FF
NETWORK
P
ACK
KA-DV5000
LST0103-001B
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Inserting/removing CF memory card/LAN card
● The KA-DV5000 accepts the following cards for which operation has
been confirmed: (As of August 2002)
Operating voltage
3.3 V
Current consumption Max. 500 mA
• Wired LAN-card
Lock release button
Cover
CF memory card or
LAN card
US:
EA2900-117 (Revision C) (Name of manufacturer: Socket
Communications, Inc)*1
Europe: EA2903-162 (Revision C) (Name of manufacturer: Socket
Communications, Inc)*1
Asia:
EA2906-194 (Revision C) (Name of manufacturer: Socket
Communications, Inc)*1
* Revision indicated on the upper right of package production label.
• Wireless LAN-card
TEW-201PC
Section A
TEW-202CF
Card slot
TEW-PC16 (firmware version 0.8.3 or later) (Name of manufacturer:
TRENDware)
WCF11 (Name of manufacturer: LINKSYS)*2
AIR-PCM350
EJECT button
(Name of manufacture: Cisco Systems)
FCCID: LDK102040
KA-DV5000
• CF (Compact Flash) card
SDCFB-16 ~ SDCFB-256 (Name of manufacturer: SanDisk)*1
*1: Use PCMCIA card TYPE 1 or TYPE 2 adapter
*2: Use PCMCIA card TYPE 2 adapter
For the latest operational check card, visit the website below
or contact your JVC dealer.
Caution
● Make sure the power of GY-DV5000 is off when inserting/
removing a CF memory card/LAN card. Inserting/removing
a card with the unit power on may damage the data storage
section of the CF memory card or the card itself.
● Do not use the wireless LAN card continuously for more
than 48 hours.
Inserting card
1.
Turn off the GY-DV5000 power.
2.
3.
Press and hold the lock release button and open the cover.
Insert a card into the KA-DV5000 card slot. Then, close the cover.
● The cover may not close depending on the wired LAN card or the card shape. In this case, remove the cover by pressing section
A and pulling on the cover.
4.
5.
Turn on the GY-DV5000 power.
Turn on the KA-DV5000 power.
LCD screen
● Card status according to the inserted card type is displayed on
the LCD screen/viewfinder screen. (ꢀ page 4)
C F
Card status display
: No card
(The viewfinder will show the status in black and white.)
Memo
When turning the power on, the card status
display shown on left will flash during initial-
ization.
: LAN card
e
: CF memory card
C
F
Removing card
1.
2.
Turn off the GY-DV5000 power, or turn off the KA-DV5000 power.
Open the cover, press the EJECT button of KA-DV5000 and remove the card.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
LCD screen/viewfinder screen
Information from Network Pack KA-DV5000 is displayed on the GY-DV5000 LCD screen/viewfinder screen.
CF FULL!
qCard status displays
wCF Memory card warning display
Displays CF memory card status and system errors.
Display
Description
No card is inserted in Network Pack.
Flashing display during initialization (after
power on).
* For details concerning warning displays, see page 46.
LAN card is inserted in Network Pack.
e
When inputting the 44.1kHz sampling audio signal
(White display)
This unit is not compatible with audio sampling frequency of
44.1kHz. When playing back a tape recorded with audio of
44.1kHz on GY-DV5000 or when inputting audio in the
44.1kHz mode into the DV terminal, the audio will be pro-
cessed as muted sound. However,the video will be processed
as normal.
Video/audio data is being sent from LAN
card.
e
(Red display)
CF memory card is inserted in Network Pack.
CF memory card is being recorded with data.
C
F
(White display)
C
F
(Red display)
Card is inserted in Network Pack but trans-
mission is not available.
X
There is possibility of unit malfunction.
Contact your nearest JVC dealer.
Flashing display
No colors will be shown on the viewfinder.
Receiving Level Indicator of Wireless LAN
If you are using wireless LAN card that can detect receiving
level, receiving level indicator is shown next to the card status
information on LCD of your camcorder. The indicator shows
value from 5 to 0, 5 means maximum level and 0 means mini-
mum level. (The indicator is for reference.The value does not
guarantee communication.)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu screen
Menu screen structure
When attaching Network Pack KA-DV5000 to DV Camcorder GY-DV5000, NETWORK PACK CONFIG menu and MOVIE CLIP menu
are added to the GY-DV5000 TOP MENU screen.
MOVIE CLIP list screen
(ꢀ page 23)
TOP MENU screen
TOP MENU screen
MOV I E C L I P
M ENU
MENU
CAMERA O P ERA T I ON
mc 0 0 0 5 . a s f
R / W
. .
AUD I O / V I D EO .
.
09 : 0 0 : 00
CAMERA P ROC E SS .
AUD I O / V I D EO .
LCD / V F .
TC / UB / C L OCK .
OT HERS .
F I L E M AN AGE .
MENU A L L RE S E T
.
02 / 03 / 02
LCD / V F .
TC / UB / C L OCK .
OT HERS .
F I L E M AN AGE .
MENU A L L RE S E T
.
.
.
.
mc 0 0 0 6 a s f
R / W
.
.
09 : 3 0 : 25
02 / 03 / 02
.
.
.
mc 0 0 0 7 a s f
R / W
CAN C E L
.
10 : 1 0 : 55
R / W
02 / 03 / 02
E TWOR K PACK C ONF I G .
.
N
.
.
mc 0 0 0 8 a s f
MOV I E CL I P .
EX I T
.
CAN C E L
11 : 0 0 : 00
02 / 03 / 02
E TWOR K PACK C ONF I G .
.
N
PAGE
B
CK
A
EX I T
* Example display when there are clip
files in the CF memory card
NETWORK MAIN SETUP menu screen
NETWORK SETUP menu screen
NETWORK MA I N
ETUP
NETWORK
S
ETUP
S
HOST NAME . .
NE TWORK SE TUP .
PORT SE TUP .
.
O F F
.
DHCP
I P ADDRE SS .
.
W I RE L ESS L AN SE T UP .
.
SERVER SE T UP .
PAGE BACK
.
SUBNET MASK .
GA TEWAY . .
.
NPAEGXET BPAGCKE
ENCODE SETUP menu screen
PORT SETUP menu screen
ENCODE
F RAME S I Z E
B I T RA T E
E TUP
POR T SET U P
S
3 2 0 x 2 4 0
HT T P for WEB Browser .
.
3 8 4 k b / s
M I D
HT T P for Media player .
.
MAX F RAME RA T E
S T REAM T YPE
PAGE BACK
RT SP for Streamproducer .
.
for WMP
RT SP for QuickTime .
PAGE BACK
.
NETWORK PACK CONFIG
menu screen
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI
N
S E T U P
ENCODE S E T U P .
MPEG R EC
.
TR I G
MOV I E
L I
C
P
S E T U P .
.
MENU R ES E T
CANCE L
MOVIE CLIP SETUP menu screen
WIRELESS LAN SETUP menu screen
PAGE
B
CK
A
( WMP u n d e r 8 ) ( C F V i e w er )
MOV I E CL I P ETUP
W I RE L ES S LA
AD HOC MODE
ETUP
OF F
S
S
S
DE L E T E A L L
CANCE L
CANCE L
REPEA T
FORMAT
Primary ESS I D .
Secondary ESS I D .
C o u n t r y
.
P L AY MODE
PAGE BACK
.
USA
CH
1 0 CH
WEP KEY .
L EAP
.
OF F
PAGE BACK
SERVER SETUP menu screen
SER VER SE TU P
SE TUP ON WEB
OF F
L EAP USER NAME .
.
.
L EAP PASSWORD .
.
H T T P USER NAME .
H T T P PASSWORD .
F T P USER NAME .
.
.
F T P PASSWORD .
PAGE BACK
.
FILE MANAGE settings
When using a CF card, “EXT1” and “EXT2” are additionally displayed in the GY-DV5000 FILE MANAGE screen of LOAD and
STORE FILE column. Saving and reading-out can be performed to and from the CF card with MENU setting value as EXT1 or
EXT2. When deleting files saved on a CF card, delete “EXT1.dat” or “EXT2.dat” file in the data folder of the CF card using a PC.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu screen
ⅷ indicates default factory setting.
NETWORK PACK CONFIG menu screen items
Item
Setting
Description
NETWORK MAIN SETUP
ENCODE SETUP
FRAME SIZE
Displays menu screen for network related settings. ( page 11)
ꢀ
Displays menu screen for setting video and audio compressions.
ⅷ320 × 240
160 × 120
Sets the video compression size.
320 × 240: Sets the image size to 320 × 240 pixels. (CIF)
160 × 120: Sets the image size to 160 × 120 pixels. (QCIF)
(1/4 image size of CIF.)
VIDEO RATE
Sets streaming speed (bps).
56K: MPEG4 24 kbps G726 16 kbps
128K: MPEG4 104 kbps G726 16 kbps
256K: MPEG4 232 kbps G726 24 kbps
384K: MPEG4 352 kbps G726 32 kbps
512K: MPEG4 472 kbps G726 40 kbps
56K
128K
256K
ⅷ384K
512K
MAX FRAME
RATE
MAX
ⅷMID
MIN
Sets the frame rate per second. Settings are as shown below.
FRAME SIZE
320 × 240 160 × 120
MAX MID MIN MAX MID MIN
FRAME SIZE
BIT RATE
(bps)
BIT RATE
(bps)
320 × 240
MAX MID MIN MAX MID MIN
NTSC 15 10 7.5 30 15 10
PAL 12.5 25 12.5 12.5
NTSC 15 10 7.5 30 15 10
160 × 120
NTSC 7.5
5
5
1
1
3
1
1
1
15 10 7.5
128K
56K
512K
384K
256K
PAL
5
3
1
12.5 12.5
10 7.5
5
5
5
5
5
NTSC
PAL
12.5
5
PAL
NTSC 15 7.5
PAL 12.5
12.5
5
5
5
5
25 12.5
30 15 7.5
25 12.5
5
* The frame rates shown in the table are not
guaranteed values.
5
5
STREAM TYPE
ⅷfor WMP
Sets the player for stream playback.
for QT
for WMP : Media Player, Streamproducer
for QT : Quick Time
Memo
• No sound will be heard when playing back using QuickTime while in the WMP mode.
• No sound will be heard when playing back using Media Player while in the QT mode.
• Set to WMP mode when recording to CF memory card.
PAGE BACK
MPEG REC
Pressing the SHUTTER dial returns to the NETWORK PACK CONFIG menu screen.
ⅷTRIG
SPLIT
OFF
Selects the operation method for recording video data to a CF memory card or sending data
to a remote media from a LAN card.
TRIG: Pressing the VTR trigger button of GY-DV5000 starts operation. Use this setting
when simultaneously recording to a DV tape.
SPLIT: Use this setting when recording or transferring with CF memory card or LAN card
only. Operation starts when pressing the VTR trigger button on the side of GY-
DV5000.
Memo
When SPLIT is selected, the unit will not operate even when pressing the VTR trigger
button on the front or on the lens.
OFF: Recording will not be made to the CF memory card and streaming data from the
LAN card will not be recorded/sent to the PC even when pressing the VTR trigger
button of GY-DV5000.
→
OVER
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu screen
NETWORK PACK CONFIG menu screen items
Item
Setting
Description
MOVIE CLIP SETUP
Displays the menu screen for CF memory card related settings such as formatting or delet-
ing all recorded clip files.
DELETE ALL
ⅷCANCEL
Selecting EXECUTE and pressing the SHUTTER dial deletes all clip files on the CF memory
EXECUTE
card.
Protected clip files are not deleted.
FORMAT
ⅷCANCEL
Selecting EXECUTE and pressing the SHUTTER dial starts formatting the card.
All recorded clips are erased.
EXECUTE
PLAY MODE
OFF
Playback is performed from the specified clip file to the latest clip file and pauses at the
specified clip file.
REPEAT 1
Specified clip file is played backed 3 times.
ⅷREPEAT
Playback is performed 3 times from the specified clip file to the latest clip file.
PAGE BACK
Pressing the SHUTTER dial returns to the NETWORK PACK CONFIG menu screen.
MENU RESET
ⅷCANCEL
Selecting EXECUTE and pressing the SHUTTER dial returns NETWORK PACK CONFIG
menu screen settings to the original factory settings.
EXECUTE
PAGE BACK
Pressing the SHUTTER dial returns to the TOP MENU screen.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu screen
Setting the NETWORK PACK CONFIG menu screen
Menu screen settings can be made regardless of whether a card is inserted. Settings will be stored in the KA-DV5000 memory even
when turning the power off.
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
SHUTTER
dial
STATUS
button
1
2
3200K
5600K
.3 5600K
.4 5600K
1
1
/
8
ND
64 ND
STATUS
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
MODE
VTR
CAM
MODE switch
POWER switch
● The NETWORK PACK CONFIG menu
\ Settings are made by viewing the LCD screen or viewfinder screen.
If OUTPUT CHAR of the OTHERS (1/2) menu screen is set to ON, the menu
screen also appears on the monitor screen connected to the MONITOR OUT or
Y/C OUT connector.
screen will not appear during card initial-
ization (flashing
display).
TOP MENU screen
1.
2.
Set the POWER switch of the GY-DV5000 and KA-DV5000 to ON.
M ENU
Set the MODE switch.
CAMERA O P ERA T I ON
. .
CAMERA P ROC E SS .
AUD I O / V I D EO .
LCD / V F
TC / UB / C L OCK .
OT HERS .
F I L E M AN AGE .
MENU A L L RE S E T
.
● Set to “CAM” when shooting a video. (Light the CAM indicator.)
● Set to "VTR" for VTR playback, clip file playback or DV signal recording. (Light
the VTR indicator.)
.
.
.
.
.
.
CAN C E L
3.
4.
Press the STATUS button for about 1 seconds. The TOP MENU screen appears.
.
N
E TWOR K P ACK C ONF I G .
EX I T
Turn the SHUTTER dial, move the cursor (t) to NETWORK PACK CONFIG and
press the SHUTTER dial.
● The NETWORK PACK CONFIG menu screen appears.
Cursor
5.
Select the item to set.
Turn the SHUTTER dial, move the cursor to the desired item to set and press the
SHUTTER dial.
NETWORK PACK CONFIG
menu screen
● The selected menu screen appears.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI
N
S E T U P
● When selecting MPEG REC or MENU RESET, the setting area flashes and the
setting can be changed. Set the item according to step 7.
● When selecting NETWORK MAIN SETUP, the network related setting screen
ENCODE S E T U P .
MPEG R EC
.
TR I G
MOV I E
L I
C
P
S E T U P .
.
C
MENU R ES E T
PAGE CK
( WMP u n d e r 8 ) ( C F V i e w e r )
ANCE L
B
A
appears. ( page 10)
ꢀ
6.
7.
Select an item within the menu screen.
Turn the SHUTTER dial, move the cursor (t) to the desired item to set and press
the SHUTTER dial.
● The setting area flashes and the setting can be changed.
Setting
NETWORK MAIN SETUP menu screen
(ꢀ page 10)
Change the setting.
Turn the SHUTTER dial to change the setting and press the SHUTTER dial.
● Flashing of the setting area stops and the new setting is confirmed.
\ When changing multiple settings, repeat steps 6 and 7 above.
ENCODE
F RAME S I Z E
B I T RA T E
E TUP
S
3 2 0 x 2 4 0
3 8 4 k b / s
M I D
8.
Return to the TOP MENU screen.
MAX F RAME RA T E
S T REAM T YPE
PAGE BACK
Turn the SHUTTER dial, move the cursor (t) to PAGE BACK and press the SHUT-
for WMP
TER dial.
9.
When quitting menu screen setting and returning to the normal screen, perform
one of the following operations.
● Press the STATUS button.
● Move the cursor (t) to EXIT in the TOP MENU screen and press the SHUTTER
Setting
dial.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu screen
Returning the NETWORK PACK CONFIG menu screen to factory settings
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
1
2
3200K
5600K
STATUS
button
SHUTTER
dial
1
1
/
8
ND
64 ND
STATUS
.3 5600K
.4 5600K
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
NETWORK PACK CONFIG
menu screen
1.
2.
Press the STATUS button for about 1 seconds to display the TOP MENU screen.
Check to see that the card status display has changed from a flashing to constant
display.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI
N
S E T U P
ENCODE S E T U P .
MPEG R EC
.
TR I G
MOV I E
L I
C
P
S E T U P .
.
3.
4.
Turn the SHUTTER dial to select NETWORK PACK CONFIG and press the SHUT-
TER dial.
EXE CUTE
MENU R ES E T
PAGE CK
( WMP u n d e r 8 ) ( C F V i
B
A
e w e r )
● The NETWORK PACK CONFIG menu screen appears.
.
.
MENU R ES E T
Turn the SHUTTER dial to set MENU RESET to “EXECUTE” and press the SHUT-
TER dial.
● When resetting the menu, “MENU RESET..” will appear at the bottom of the
screen for about 5 seconds.
● The NETWORK PACK CONFIG menu screen settings will return to the factory
settings.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Network settings
Setting the NETWORK MAIN SETUP menu screen
When using a LAN card, network related settings for KA-DV5000 are made using NETWORK MAIN SETUP of the NETWORK PACK
CONFIG menu. Settings will be stored in the KA-DV5000 memory even when turning the power off.
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
SHUTTER
dial
STATUS
button
1
2
3200K
5600K
.3 5600K
.4 5600K
1
1
/
8
ND
64 ND
STATUS
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
POWER switch
TOP MENU screen
\ Settings are made by viewing the LCD screen or viewfinder screen.
If OUTPUT CHAR of the OTHERS (1/2) menu screen is set to ON, the menu screen
also appears on the monitor screen connected to the MONITOR OUT or Y/C OUT
connector.
M ENU
CAMERA O P ERA T I ON
. .
CAMERA P ROC E SS .
.
AUD I O / V I D EO .
LCD / V F .
TC / UB / C L OCK .
OT HERS .
F I L E M AN AGE .
MENU A L L RE S E T
.
.
.
.
.
CAN C E L
.
N
E TWOR K PACK C ONF I G .
Display the NETWORK SETUP menu screen
EX I T
1.
2.
Turn on the GY-DV5000 and KA-DV5000 power.
Check to see that the card status display has changed from a flashing to constant
display.
NETWORK PACK CONFIG
menu screen
N ETWORK
A CK
ON I G
P
C
F
3.
4.
Press the STATUS button for about 1 seconds to display the TOP MENU screen.
NET WORK MAI
N
S E T U P .
.
ENCODE S E T U P .
MPEG R EC
.
TR I G
MOV I E
L I
C
P
S E T U P .
.
Turn the SHUTTER dial, move the cursor (t) to NETWORK PACK CONFIG and
press the SHUTTER dial.
MENU R ES E T
PAGE CK
CANCE L
B
A
( WMP u n d e r 8 ) ( C F V i e w e r )
● The NETWORK PACK CONFIG menu screen appears.
5.
Turn the SHUTTER dial, move the cursor (t) to NETWORK MAIN SETUP and
press the SHUTTER dial.
● The NETWORK MAIN SETUP menu screen will appear.
The NETWORK MAIN SETUP menu screen is structured by four screens.
NETWORK SETUP
NETWORK MAIN SETUP menu screen
NETWORK MA I N
ETUP
S
PORT SETUP
NE TWORK SE TUP .
PORT SE TUP .
.
.
WIRELESS LAN SETUP
W I RE L E SS L AN SE T UP .
.
SERVER SE T UP .
PAGE BACK
.
SERVER SETUP
6.
Turn the SHUTTER dial, move the cursor (t) to SETUP and press the SHUTTER
dial.
● The selected SETUP screen appears.
Items with “..” at the end of the name are set in the INPUT screen.
7.
8.
To return to the NETWORK MAIN SETUP menu screen, select PAGE BACK and
press the SHUTTER dial.
NETWORK SETUP menu screen
NETWORK
ETUP
S
To return to the normal screen after completing setting, perform one of the follow-
ing operations.
HOST NAME . .
– – –
DHCP
I P ADDRE SS .
.
SUBNET MASK .
GA TE WAY . .
NPAEGXET BPAGCKE
.
● Press the STATUS button
● Select PAGE BACK to return to the TOP MENU screen. Select EXIT in the TOP
MENU screen and press the SHUTTER dial.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Network settings
NETWORK MAIN SETUP menu screen items
NETWORK SETUP menu screen ⅷ indicates default factory setting.
Item
Setting
Description
HOST NAME
Displays the host name input setting screen. (4 ~ 64 alphanumerical characters)
[Factory setting: none]
DHCP
ⅷOFF Select whether DHCP server is used.
ON
OFF: Use this setting when using LAN connection rather than DHCP.
When this setting is used, IP ADDRESS and SUBNET MASK, GATEWAY must also be set.
ON: Use this setting when using DHCP connection.
When using this setting, IP ADDRESS and SUBNET MASK, GATEWAY are automatically set.
* When DHCP is set to ON, WLAN ADHOC MODE cannot be set to AHDM or IBSS.
IP ADDRESS
Displays the IP address setting screen.
When using LAN connection with DHCP set to OFF, this setting is required. Set a unique IP address.
IP ADDRESS setting is not available when DHCP is set to ON.
[Factory setting] 192.168.100.101]
SUBNET MASK
Displays the subnet mask input screen.
This setting is required when using LAN connection with DHCP set to OFF.
SUBNET MASK setting is not available if DHCP is set to ON.
[Factory setting: 255.255.255.000]
GATE WAY
Displays the gateway address input screen.
GATEWAY setting is not available when DHCP is set to ON.
[Factory setting: 192.168.100.254]
PAGE BACK
Pressing the SHUTTER dial returns to the NETWORK MAIN SETUP menu screen.
PORT SETUP menu screen
Item
Setting
Description
HTTP for WEB
Browser
1
The screen for setting RTSP and HTTP port numbers appears.
:
ⅷ80
:
HTTP for Web Browser can be set with the Web browser HTTP port number and HTTP for Media
Player can be set with the Media Player HTTP port number. RTSP for Streamproducer can be set
with the Streamproducer RTSP port number and RTSP for Quick Time can be set with the Quick
32767 Time RTSP port number.
Normally, the unit can be used without changing the factory settings.
If there are port restrictions for the LAN environment of your PC, consult your network administrator.
HTTP for
Media player
1
:
ⅷ8080
* When changing a port number, refer to “5-1. Connecting with Camcorder” of the “Streamproducer”
User’s Guide of the network distribution software to change settings.
:
32767
* Do not use the same port numbers for RTSP and HTTP.
RTSP for
1
Streamproducer
:
ⅷ8554
:
* When a port number is changed, switch the power of the GY-DV5000 off once, and then switch it
on again.
32767
RTSP for Quick
Time
1
:
ⅷ554
:
32767
PAGE BACK
Pressing the SHUTTER dial returns to the NETWORK SETUP menu screen.
→
OVER
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Network settings
NETWORK MAIN SETUP menu screen items
WIRELESS LAN SETUP menu screen ⅷ indicates default factory setting.
Item
Setting
Description
AD HOC MODE
ⅷOFF Wireless LAN setting
AHDM OFF:
Use this setting when performing communication via access point.
IBSS AHDM/IBSS: Use this setting when performing communication in AD HOC mode with a PC con-
nected with a wireless LAN card. ( page 16)
ꢀ
* When this item is set to AHDM or IBSS, DHCP cannot be set to ON.
Primary ESS ID
NONE Displays the wireless LAN ESS-ID input setting screen (Max. 32 alphanumerical characters)
Secondary ESS ID NONE
Country
ⅷUSA Setting for the country using wireless LAN
EU USA: USA, EU: Europe, FRN: France
FRN SPN: Spain, JPN: Japan
SPN (Set according to operating environment.)
JPN
CH
1CH Wireless LAN channel setting
:
CH setting changes depending on the Country setting.
ⅷ10CH USA: 1 ~ 11CH, EU: 1 ~ 13CH, FRN: 10 ~ 13CH, SPN: 10, 11CH, JPN: 1 ~ 14CH
:
14CH
WEP KEY
LEAP
When encrypting data, set the WEP KEY (10 or 26 characters consisting or letters a ~ f and num-
bers). Must be compatible with access point authentication for the use of this item.
ON
ⅷOFF
Set to ON when connecting a Cisco Systems wireless LAN device and using the LEAP function.
Memo
The LEAP function is exclusive to Cisco Systems wireless LAN devices. For details concerning
the LEAP function, see the instruction manual accompanying the wireless LAN device.
PAGE BACK
Pressing the SHUTTER dial returns to the NETWORK MAIN SETUP menu screen.
SERVER SETUP menu screen
Item
Setting
Description
SETUP ON WEB
ON
ⅷOFF
Set to ON when changing the USER NAME and PASSWORD from the Web.
Memo
If higher security is desired, set this function to OFF so that changes cannot be made from the
Web.
LEAP USER
NAME
Displays the LEAP USER NAME input screen. (4 ~ 32 alphanumerical characters)
Set when using the LEAP function.
[Default setting: leap-user]
LEAP
PASSWORD
Displays the LEAP PASSWORD input screen. (4 ~ 32 alphanumerical characters)
Set when using the LEAP function.
[Default setting: ka-dv-jvc]
HTTP USER
NAME
Displays the HTTP USER NAME input screen. (3 ~ 8 alphanumerical characters)
Set when connecting from the Web browser.
[Default setting: jvc]
HTTP
PASSWORD
Displays the HTTP PASSWORD input screen. (4 ~ 8 alphanumerical characters)
Set when connecting from the Web browser.
[Default setting: ka-dv5k]
FTP USER NAME
FTP PASSWORD
PAGE BACK
Displays the FTP USER NAME input screen. (3 ~ 8 alphanumerical characters)
Used when uploading USER PAGE.
[Default setting: ftp-user]
Displays the FTP PASSWORD input screen. (4 ~ 8 alphanumerical characters)
Used when uploading USER PAGE.
[Default setting: ka-dv]
Pressing the SHUTTER dial returns to the NETWORK MAIN SETUP menu screen.
Memo
For details concerning user name and password settings, see page 13.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Network settings
\ Changing the user name
Setting user names and passwords
When changing the HTTP USER NAME or FTP USER NAME, “NEXT STEP SET PASSWORD” will appear on the screen and the
PASSWORD menu screen is displayed.
When input is canceled in the PASSWORD menu screen, the user name will also be canceled.
It is possible to change only the password.
When changing the LEAP USER NAME setting, the PASSWORD menu screen will not appear automatically.
\ Setting passwords
Set LEAP, HTTP and FTP PASSWORD using the procedure shown below.
1.
2.
3.
First, enter the currently used password when “ENTER OLD PASSWORD” is displayed.
Next, enter the new password when “ENTER NEW PASSWORD” is displayed.
Lastly, enter the new password again when “CONFIRM NEW PASSWORD” is displayed.
Caution
• Do not forget to take a memo of the password. The password cannot be redisplayed.
• Each character input on the PASSWORD menu screen is hidden using asterisks (*).
• When performing MENU RESET, the unit will return the default factory settings.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Network settings
Network related settings are made in the individual input setting screens.
Making network related settings
Here, HTTP USER NAME is set as an example. Other settings are also made in the same manner.
STOP button
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
1
2
3200K
5600K
SHUTTER
dial
STATUS
button
1
1
/
8
ND
64 ND
STATUS
.3 5600K
.4 5600K
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
HTTP USER NAME input setting screen
Currently inputted number of characters/
max.number of characters
Example: Changing HTTP USER NAME from jvc to jvc-1234
HTTP USER NAME
3
8
/
\ Select HTTP USER NAME in the SERVER SETUP menu screen and press the
SHUTTER dial.
j v c
● The USER NAME input setting screen appears.
1.
Characters are selected from the character selection area on the bottom of the
screen.
a b c d e f h i
j
k l m n o p q r s t u v
g
_
wx y z 0 1 3 4 5 6 7 8 9
6
2
¯ .
BSA
Turn the SHUTTER dial to flash “_” in the character selection area and press the
SHUTTER dial.
Setting area
Character
selection area
● The setting changes to “jvc_” and the following digit of the setting area flashes.
BS: Backspace (delete previous character
)
2.
3.
Turn the SHUTTER dial to select “1” in the character selection area and press the
SHUTTER. dial.
: The set text is confirmed and
returns to the previous screen.
● The setting changes to “jvc_1” and the following digit of the setting area flashes.
6: The set text is canceled and
returns to the previous screen.
Repeat the above step to set “jvc_1234” in the setting area.
HTTP USER NAME
4
\ To delete or edit set characters, select “BS” within the character selection area and
8
/
press the SHUTTER dial.
_
j v c
The previous character will be deleted. The character on the left will be deleted each
time this operation is repeated.
\ When turning the SHUTTER dial while holding down the STOP button, the cursor will
a b c d e f h i
j
k l m n o p q r s t u v
g
move 5 characters at a time.
_
6
wx y z 0 1 3 4 5 6 7 8 9
¯
.
BSA
2
\ The currently inputted number of characters and the maximum number of characters
are displayed on the upper right of the screen.
HTTP USER NAME
\ To cancel a setting, select the “6” within the character selection area and press the
SHUTTER dial. The unit will return to the previous screen (SERVER SETUP menu
screen).
5
8
/
_
j v c
1
4.
When completed, select “ ” within the character selection area and press the
SHUTTER dial.
a b c d e f h i
j
k l m n o p q r s t u v
g
_
¯
6
wx y z 0 1 3 4 5 6 7 8 9
.
2
BSA
● When changing the HTTP USER NAME or FTP USER NAME, “NEXT STEP
SET PASSWORD” will appear on the screen and the PASSWORD menu screen
is displayed . Set the password using the procedure shown above.
HTTP USER NAME
8
/
8
_
Memo
j v c 1 2 3 4
When setting is completed for items other than HTTP USER NAME and FTP USER
NAME, the unit will return to the previous screen (NETWORK MAIN SETUP or
SERVER SETUP menu screen).
a b c d e f h i
j
k l m n o p q r s t u v
g
_
¯
6
wx y z 0 1 3 4 5 6 7 8 9
2
.
BSA
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Network settings
Example of IP address and subnet mast settings when using LAN is shown below.
Detailed IP settings (LAN)
●Operation is only guaranteed for Windows 2000, Windows XP Home Edition or Windows XP Professional.
●Internet Explorer 5.0 or later
●Windows Media Player 7.01 or later (WM9 is not supported.)
1. For 1:1 communication between PC and GY-DV5000/KA-DV5000
OPEN
EDITSEEARCH
MONITOR
FILTER
1
2
3200K
5
6
0
0
K
1
/
8
ND
.
3
5
6
0
0
K
.
4
5
6
0
0
K
1
/
6
4
N
D
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
PACK
KA-DV5000
10/100 BASE-T cross cable
POWER
VTR
ON
OFF
* For the PC settings when using a LAN card,
refer to the instruction manual included with
the LAN card.
Set a unique number to avoid doubling
* Up to 3 clients can access at the same time.
DHCP OFF
PROXY SERVER NO USE
DHCP SERVER NO USE
IP ADDRESS 192. 168. 100. 100
IP ADDRESS 192. 168. 100. 101
NETMASK 255. 255. 255. 000
NETMASK
255. 255. 255. 000
Set the same network group
2. For communication between PC and multiple GY-DV5000/KA-DV5000
DHCP OFF
IP ADDRESS 192. 168. 100. 101
OPEN
EDITSEEARCH
MONITOR
FILTER
1
2
3200K
5
6
0
0
K
1
/
8
ND
.3 5600K
.4 5600K 1/64 ND
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
NETMASK
255. 255. 255. 000
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
PROXY SERVER NO USE
DHCP SERVER NO USE
IP ADDRESS 192. 168. 100. 100
DHCP OFF
IP ADDRESS 192. 168. 100. 102
NETMASK
255. 255. 255. 000
OPEN
EDITSEEARCH
MONITOR
FILTER
1
2
3200K
5
6
0
0
K
1
/
8
ND
.3 5600K
.4 5600K 1/64 ND
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
PACK
KA-DV5000
NETMASK
255. 255. 255. 000
POWER
VTR
ON
OFF
Hub
DHCP OFF
OPEN
EDITSEEARCH
MONITOR
FILTER
3200K
1
2
5
6
0
0
K
1
/
8
ND
.3 5600K
.4 5600K 1/64 ND
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
IP ADDRESS 192. 168. 100. 103
NETMASK 255. 255. 255. 000
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
10/100 BASE-T straight cable
Caution
Set a unique number to avoid doubling
DHCP OFF
IP ADDRESS 192. 168. 100. 104
NETMASK 255. 255. 255. 000
OPEN
EDITSEEARCH
MONITOR
FILTER
3200K
5600K 1/
1
2
8
ND
IP ADDRESS 192. 168. 100. XXX
.
3
5
6
0
0
K
.
4
5
6
0
0
K
1
/
6
4
N
D
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
PACK
KA-DV5000
NETMASK
255. 255. 255. 000
POWER
VTR
ON
OFF
Set the same network group
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Network settings
Example of network settings when using wireless LAN is shown below.
Detailed network settings (WLAN)
●Operation is only guaranteed for Windows 2000, Windows XP Home Edition or Windows XP Professional.
●Internet Explorer 5.0 or later
●Windows Media Player 7.01 or later (WM9 is not supported.)
1. For communication with PC without returning access point (Ad hoc mode)
OPEN
EDITSEEARCH
* Do not perform encryption of the
MONITOR
FILTER
3200K
1
2
5
6
0
0
K
1
/
8
ND
.3 5600K
.4 5600K 1/64 ND
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
PACK
KA-DV5000
wireless LAN.
POWER
VTR
ON
OFF
Set a unique number to avoid doubling
DHCP
OFF
WLAN AD HOC MODE ON
WLAN ESS ID
WLAN CH
IP ADDRESS
NETMASK
abcdef
2
192. 168. 100. 101
255. 255. 255. 000
PROXY SERVER
DHCP SERVER
IP ADDRESS
NETMASK
OFF
OFF
192. 168. 100. 100
255. 255. 255. 000
Set the same network group
PC wireless LAN driver settings
NetworkType
ESS ID
802. 11 Ad Hoc Mode
abcdef
Channel
2
Encryption Mode
Open System
* For the PC settings when using a LAN card, refer to
the instruction manual included with the LAN card.
Cautionary items concerning Wireless LAN (WLAN)
● For the WLAN ESS ID, input the values of ESSID set in:
Ad hoc mode: PC of other party
Infrastructure: Access point
● WLAN AD HOC MODE
When IBSS is set, the NETWORK MODE setting of the wireless LAN card on the PC side must be set to 802.11 Adhoc.
When AHDM is set, the NETWORK MODE setting of the wireless LAN card on the PC side must be set to Adhoc. Depending
on the LAN card on the PC side, only 802.11 Adhoc mode may be available.
● WLAN CH is the wireless frequency band used for communication. If there is an access point, adapter, etc., using the
same band in the proximity, there may be a hindrance in the communication and may reduce throughput or the quality of
communication. When setting, check the settings of surrounding access points, etc., to avoid doubling.
2417 2427 2437 2447 2457 2467
Frequency bands (ISM bands) and channels
(IEEE803.11b standard)
2412
2422 2432 2442 2452 2462 2472
2484
Approx.
11MHz
Center
frequency
1ch
2ch
3ch
4ch
5ch
6ch
7ch
8ch
9ch
10ch
11ch
12ch
13ch
N. America : FCC / 2.412~2.462GHz (11 channels)
Europe
Japan
France
Spain
: CE ETSI / 2.412~2.472GHz (13 channels)
: 2.412~2.4835GHz (14 channels)
: 2.457~2.472GHz (4 channels)
: 2.457~2.462GHz (2 channels)
Since adjacent channels causes signal interference, channels
are normally spaced 5 channels apart.
(Set according to operating environment.)
14ch
1ch frequency band
6ch frequency band
11ch frequuencyy band
1c4hchfrferqeuquenecnycybabnadnd
→
OVER
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Network settings
Detailed network settings (WLAN)
2. For communication with PC via access point (Infrastructure mode)
DHCP
OFF
WLAN AD HOC MODE OFF
WLAN ESS ID
WLAN CH
abcdef
2
IP ADDRESS
NETMASK
192. 168. 100. 101
255. 255. 255. 000
DHCP
OFF
WLAN AD HOC MODE OFF
OPEN
EDITSEEARCH
MONITOR
FILTER
1
2
3200K
5
6
0
0
K
1
/
8
ND
.3 5600K
.4 5600K 1/64 ND
WLAN ESS ID
WLAN CH
abcdef
2
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
IP ADDRESS
NETMASK
192. 168. 100. 102
255. 255. 255. 000
OPEN
EDITSEEARCH
MONITOR
FILTER
3200K
1
2
5
6
0
0
K
1
/
8
ND
.
3
5
6
0
0
K
.
4
5
6
0
0
K
1
/
6
4
N
D
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
STATION
ESS ID abcdef
Channel 2
Encryption Mode Open System
PROXY SERVER
DHCP SERVER
IP ADDRESS
NETMASK
NO USE
NO USE
192. 168. 100. 100
255. 255. 255. 000
OPEN
EDITSEEARCH
MONITOR
FILTER
3200K
1
2
5
6
0
0
K
1
/
8
ND
.3 5600K
.4 5600K 1/64 ND
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
ACK
KA-DV5000
P
POWER
VTR
ON
OFF
PC wireless LAN driver settings
NetworkType
ESS ID
Channel
Infrastructure
abcdef
2
DHCP
OFF
WLAN AD HOC MODE OFF
WLAN ESS ID
WLAN CH
abcdef
2
Encryption Mode
Open System
* For the PC settings when using a LAN card,
refer to the instruction manual included with
the LAN card.
IP ADDRESS
NETMASK
192. 168. 100. 103
255. 255. 255. 000
OPEN
EDITSEEARCH
MONITOR
FILTER
1
2
3200K
5
6
0
0
K
1
/
8
ND
.
3
5
6
0
0
K
.
4
5
6
0
0
K
1
/
6
4
N
D
POWER
SUPPL
Y
STATUS
SHUTTER
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
MENU
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
A
U
T
O
I
R
I
S
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1 CH-2
UDIO INPUT
UDIO SELECT
CH-1 CH-2
MODE
A
A
B
A
C
K
L
STRETCH
NORMAL
COMPRESS
VTR
NORMAL
SPOT L
A
UT
O
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
Network Type (Ad Hoc/Infrastructure)
Make sure ESS ID and Channel settings
are the same.
DHCP
OFF
WLAN AD HOC MODE OFF
Set a unique number to avoid doubling
WLAN ESS ID
WLAN CH
abcdef
2
IP ADDRESS
NETMASK
192. 168. 100. XXX
255. 255. 255. 000
IP ADDRESS
NETMASK
192. 168. 100. 104
255. 255. 255. 000
Set the same network group
Memo
For network settings and LAN card driver settings, refer to the respective instruction manuals.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on a CF card
Formatting a CF memory card
If the CF memory card is unformatted when performing any of the operations shown below, “NO CF FORMAT” will appear in the LCD
screen/viewfinder screen.
• Executing DELETE ALL
• Recording to the CF memory card
Caution
STATUS
If the unit enters MOVIE CLIP by oper-
ating the menu or the VCR trigger but-
ton during formatting CF card, a display
of the LCD viewer can go wrong. How-
ever, if you operate the menu after for-
matting has been completed, you will be
able to regain a normal display.
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
3200K
1
2
SHUTTER
dial
STATUS
button
1
5600K
/
8
ND
64 ND
STATUS
.3 5600K
.4 5600K
1
/
POWER
SUPPL
Y
SHUTTER
LCD BRIGHT
DISPLAY
ON OFF
MENU
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
BACK
NORMAL
SPOT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
VTR
CH-1
CH-2
L
AUTO
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
1.
2.
Press the STATUS button for about 1 seconds to display the TOP MENU screen.
C F
Use the SHUTTER dial to select NETWORK PACK CONFIG menu screen ¥
NO CF FORMAT!
MOVIE CLIP SETUP menu screen.
3.
Set FORMAT in the MOVIE CLIP SETUP menu screen to “EXECUTE” and press
the SHUTTER dial.
● The formatting begins. During formatting, “FORMAT” appears on the screen.
NETWORK PACK CONFIG
menu screen
4.
5.
When formatting is completed, to the MOVIE CLIP SETUP menu screen returns.
The FORMAT setting will return to CANCEL.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI N S E T U P
To return to the NETWORK PACK CONFIG menu screen, select PAGE BACK and
press the SHUTTER dial.
ENCODE S E T U P .
MPEG R EC
.
TR I G
MOV I E
L I
C
P
S E T U P .
.
MENU R ES E T
CANCE L
● To return to the normal screen, press the STATUS button.
PAGE
B
CK
A
( WMP u n d e r 8 ) ( C F V i e w e r )
CF memory recording time
Estimated recording time of CF memory cards is shown below:
MOVIE CLIP SETUP
menu screen
BIT RATE
CF memory
card size
MOV I E CL I P ETUP
S
DE L E T E AL L
CANCE L
EXECUTE
REPEA T
384kbps
3min.
256kbps
5min.
128kbps ~ 56kbps
10min. or more
20min. or more
40min. or more
80min. or more
120min. or more
160min. or more
FORMAT
P L AY MODE
PAGE BACK
16MByte
32MByte
64MByte
128MByte
192MByte
256MByte
7min.
11min.
22min.
44min.
66min.
88min.
M
F OR AT
15min.
30min.
46min.
61min.
Set to EXECUTE
Flashing display during
formatting
MOVIE CLIP SETUP
menu screen
Caution
MOV I E CL I P ETUP
S
The actual recording time may differ from the estimate recording time shown above
depending on the recording subject and movement.
DE L E T E A L L
CANCE L
CANCE L
REPEA T
FORMAT
P LAY MODE
PAGE BACK
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on a CF card
Recording video on a DV cassette tape and CF memory card
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
1
2
3200K
5600K
1
1
/
8
ND
64 ND
STATUS
.3 5600K
.4 5600K
STATUS button
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
OFF ZEBRA
SKIN
AREA
AUTO
WHITE
ON
ACCU
FOCUS
POWER
VTR
ON
OFF
VTR
AUDIO
LEVELE CH-1
5
MODE
VTR
CAM
MODE switch
VTR trigger button
POWER switch
VTR trigger button
● “NO CF FORMAT!” will appear if the in-
serted CF memory card is not formatted.
Format the card in the MOVIE CLIP SET
1.
2.
Insert a CF memory card into the Network Pack.
Turn on the GY-DV5000 and KA-DV5000 power.
C F
Check to see that the
display appears on the LCD screen/viewfinder screen.
menu screen. ( page 18)
ꢀ
(When the power is turned on,
display will flash during initialization.)
3.
4.
5.
Insert a recordable DV cassette tape.
LCD screen
Set the MODE switch to “CAM”. (Light the CAM indicator.)
Set the NETWORK PACK CONFIG menu screen.
q Set MPEG REC to “TRIG”.
C F
w Set the video/audio compression in the ENCODE SETUP menu screen.
(
page 6)
ꢀ
e When completed with settings, press the STATUS button to return to the normal
screen.
6.
Press the VTR trigger button on GY-DV5000 to start recording on the DV cassette
tape as well as video/audio streaming data on the CF memory card.
C F
ⅷ
:Red display during
recording
C F
● During CF memory card recording, ⅷ
display will light red.
:
Initializing
7.
8.
9.
To stop recording, press the VTR trigger button.
To resume recording, press the VTR trigger button once more.
To end recording, press the VTR trigger button.
NETWORK PACK CONFIG
menu screen
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI
N
S E T U P
C F
indicator on the LCD
ENCODE S E T U P .
MPEG R EC
.
* Before turning off the power, check to make sure the
screen is white.
TR I G
MOV I E
L I
C
P
S E T U P .
.
MENU R ES E T
PAGE CK
CANCE L
B
A
C F
Turning the power off when the
file.
indicator is red will damage the recorded clip
( WMP u n d e r 8 ) ( C F V i e w e r )
Memo
● When the DV cassette tape has reached the end during recording, CF memory
card recording will also stop.
Set to TRIG
ENCODE SETUP menu screen
● Every time recording is performed, the recorded event is stored in the clip list of
the CF memory card.
Stored contents of clip list: Clip number and date/time when recording was started.
All events can be played back on the MOVIE CLIP screen. ( page 23)
ꢀ
LCD screen
● The CF memory card remaining warning is displayed on the LCD screen/viewfinder
screen. ( page 46)
ꢀ
● If recording into the CF card is carried out within 5 seconds, either a file cannot be
made or it becomes difficult to display a thumbnail (a still picture displayed when
CLIP FILE is selected).
C F
● Do not switch over the CAM/VTR mode during recording into the CF card. If the
mode is switched over during recording, the display of the LCD viewer can go
wrong once in a while. Also, if the mode is switched over immediately after the
start of recording into the CF card, some black images can be mixed into a re-
corded picture.
● When recording to a CF Memory Card while in the TRIG mode, ***.csv file will be
created for viewing using the CFViewer.
The CSV file name will be the value of the user's bit (UB) set in GY-DV5000. For
details concerning UB, please refer to the operator’s manual of GY-DV5000.
Time code on CSV files will differ slightly from the actual time code.
CF memory card
remaining warning
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on a CF card
Recording video on a CF memory card only
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
1
2
3200K
5600K
1
1
/
8
ND
64 ND
STATUS
STATUS button
.3 5600K
.4 5600K
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
MODE
VTR
CAM
MODE switch
VTR trigger button
POWER switch
● “NO CF FORMAT!” will appear if the in-
serted CF memory card is not formatted.
Format the card in the MOVIE CLIP SET
menu screen. (ꢀ page 18)
1.
2.
Insert a CF memory card into the Network Pack.
Turn on the GY-DV5000 and KA-DV5000 power.
C F
Check to see that the
display appears on the LCD screen/viewfinder screen.
(When the power is turned on,
display will flash during initialization.)
LCD screen
3.
4.
Set the MODE switch to “CAM”. (Light the CAM indicator.)
Set the NETWORK PACK CONFIG menu screen.
q Set MPEG REC to “SPLIT”.
C F
w Set the video/audio compression in the ENCODE SETUP menu screen.
(
page 6)
ꢀ
e When completed with settings, press the STATUS button to return to the
normal screen.
C F
ⅷ
: Red display during
recording
5.
Press the VTR trigger button on side panel of GY-DV5000 to start recording stream-
ing data on the CF memory card.
:
Initializing
C F
● During recording, ⅷ
display will light red.
NETWORK PACK CONFIG
menu screen
6.
7.
8.
To stop recording, press the VTR trigger button on side panel.
To resume recording, press the VTR trigger button on side panel once more.
To end recording, press the VTR trigger button on side panel.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI
N
S E T U P
ENCODE S E T U P .
MPEG R EC
.
S P L I T
MOV I E
L I
C
P
S E T U P .
.
MENU R ES E T
PAGE CK
CANCE L
B
A
C F
* Before turning off the power, check to make sure the
screen is white.
indicator on the LCD
( WMP u n d e r 8 ) ( C F V i e w e r )
Memo
Set to SPLIT
● When recording only to the CF memory card, the clip list will not be registered.
ENCODE SETUP menu screen
● The CF memory card remaining warning is displayed on the LCD screen/viewfinder
screen. ( page 46)
ꢀ
● When MPEG REC is set to “SPLIT”, recording is performed only when the VTR
trigger button on the side is pressed.The VTR trigger buttons on the front and on
the lens are disabled.
LCD screen
● Do not switch over the CAM/VTR mode during recording into the CF card. If the
mode is switched over during recording, the display of the LCD viewer can go
wrong once in a while. Also, if the mode is switched over immediately after the
start of recording into the CF card, some black images can be mixed into a re-
corded picture.
C F
CF memory card
remaining warning
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on a CF card
Recording playback signals of a DV cassette tape on a CF memory card
STATUS
SHUTTER
BLANK SEARCH REW
STOP
FF
PLAY
STILL
MENU
OPEN
EDITSEARCH
FILTER
MONITOR
1
2
3200K
5600K
STATUS button
1
1
/
8
ND
64 ND
STATUS
.3 5600K
.4 5600K
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
POWER SUPPLY
switch
ON OFF
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
PLAY button
POWER
VTR
ON
OFF
MODE
VTR
MODE switch
VTR trigger button
CAM
POWER switch
1.
2.
Insert a CF memory card into the Network Pack.
Turn on the GY-DV5000 and KA-DV5000 power.
● “NO CF FORMAT!” will appear if the in-
serted CF memory card is not formatted.
Format the card in the MOVIE CLIP SET
C F
Check to see that the
display appears on the LCD screen/viewfinder screen.
menu screen. ( page 18)
ꢀ
(When the power is turned on,
display will flash during initialization.)
3.
4.
5.
Insert the recorded DV cassette tape.
Set the MODE switch to “VTR”. (Light the VTR indicator.)
LCD screen
Set the NETWORK PACK CONFIG menu screen.
q Set MPEG REC to “SPLIT”.
C F
w Set the video/audio compression in the ENCODE SETUP menu screen.
(
page 6)
ꢀ
e When completed with settings, press the STATUS button to return to the normal
screen.
6.
7.
Press the PLAY button of GY-DV5000 to start DV cassette tape playback.
C F : Red display during
•
recording
Press the VTR trigger button on side panel at the scene to start recording on the
CF memory card.
: Initializing
C F
● During recording, the ⅷ
display appears in red.
NETWORK PACK CONFIG
menu screen
8.
9.
To stop recording, press the VTR trigger button on side panel.
To resume recording, press the VTR trigger button on side panel once more.
To end recording, press the VTR trigger button on side panel.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI
N
S E T U P
ENCODE S E T U P .
MPEG R EC
.
S P L I T
MOV I E
L I
C
P
S E T U P .
.
MENU R ES E T
PAGE CK
CANCE L
10.
B
A
( WMP u n d e r 8 ) ( C F V i e w e r )
C F
* Before turning off the power, check to make sure the
screen is white.
indicator on the LCD
Memo
Set to SPLIT
● When recording only to the CF memory card, the clip list will not be registered.
ENCODE SETUP
menu screen
● The CF memory card remaining time is displayed on the LCD screen/viewfinder
LCD Screen
screen.
● Do not switch over the CAM/VTR mode during recording into the CF card. If the
mode is switched over during recording, the display of the LCD viewer can go
wrong once in a while. Also, if the mode is switched over immediately after the
start of recording into the CF card, some black images can be mixed into a re-
corded picture.
C F
● While recording DV input to a CF Memory Card in the SPLIT mode, do not oper-
ate the VTR section. Recording to the CF Memory Card may stop as a result.
CF memory card remaining warning
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on a CF card
Deleting all clip files on a CF memory card
MOVIE CLIP SETUP of the NETWORK PACK CONFIG menu screen is used to delete all clips on a CF memory card.
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
1
2
3200K
5600K
SHUTTER
dial
STATUS
button
1
1
/
8
ND
64 ND
STATUS
.3 5600K
.4 5600K
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
POWER switch
NETWORK PACK CONFIG
menu screen
1.
2.
Insert an already recorded CF memory card.
Turn on the GY-DV5000 and KA-DV5000 power.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI N S E T U P
C F
Check to see that the
(The
display appears on the LCD screen/viewfinder screen.
ENCODE S E T U P .
MPEG R EC
.
TR I G
mark will flash when first turning on the power or during initialization.)
MOV I E
L I
C
P
S E T U P .
.
MENU R ES E T
CANCE L
PAGE
B
CK
A
3.
4.
Press the STATUS button for about 1 seconds to display the TOP MENU screen.
( WMP u n d e r 8 ) ( C F V i e w e r )
Use the SHUTTER dial to select NETWORK PACK CONFIG menu screen ¥
MOVIE CLIP SETUP menu screen.
5.
Set DELETE ALL in the MOVIE CLIP SETUP menu screen to “EXECUTE” and
press the SHUTTER dial.
MOVIE CLIP SETUP
menu screen
● Deletion is executed and “DELETE..” appears flashing on the screen.
MOV I E CL I P ETUP
S
DE L E T E A L L
EXECUTE
CANCE L
REPEA T
FORMAT
6.
7.
When deletion is completed, to the MOVIE CLIP SETUP menu screen returns.
P L AY MODE
PAGE BACK
DELETE ALL setting will return to “CANCEL”.
\ To return to the NETWORK CONFIG menu screen, select PAGE BACK and
press the SHUTTER dial.
\ To return to the normal screen, press the STATUS button.
Memo
Set to EXECUTE
● Protected clips are not deleted.
Deleting
MOV I E CL I P ETUP
S
DE L E T E A L L
EXECUTE
CANCE L
REPEA T
FORMAT
P L AY MODE
PAGE BACK
DELETE..
MOVIE CLIP SETUP
menu screen
MOV I E CL I P ETUP
S
DE L E T E A L L
CANCE L
CANCE L
REPEA T
FORMAT
P L AY MODE
PAGE BACK
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie clip
Playing back video/audio recorded on a CF memory card
When simultaneously recording the camera video to a DV cassette and CF memory card, recording event will be registered to the clip
list of the CF memory card each time recording is performed.The clip list is stored with the recorded event number (clip number) and the
date/time when the recording was started. All events (clip numbers) can be played back on the MOVIE CLIP screen.
STATUS
BLANK SEARCH REW
STOP
FF
PLAY
STILL
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
3200K
1
2
STATUS
button
SHUTTER
dial
1
5600K
.3 5600K
.4 5600K
/
8
ND
64 ND
STATUS
REW button
1
/
POWER
SUPPL
Y
SHUTTER
LCD BRIGHT
DISPLAY
ON OFF
MENU
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
AUDIO SELECT
FF button
BACK
NORMAL
SPOT
L
STRETCH
NORMAL
COMPRESS
VTR
CH-1
CH-2
L
AUTO
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
MODE
VTR
CAM
MODE switch
POWER switch
1.
2.
Insert an already recorded CF memory card.
Turn on the GY-DV5000 and KA-DV5000 power.
● MOVIE CLIP will not appear during card
initialization (flashing display).
C F
Check to see that the
display appears on the LCD screen/viewfinder screen.
display will flash during initialization.)
(When the power is turned on,
TOP MENU screen
3.
4.
5.
Set the MODE switch to “VTR”. (Light the VTR indicator.)
Make sure GY-DV5000 is not in operation.
MENU
AUD I O / V I D EO .
LCD / V F .
TC / UB / C L OCK .
OT HERS .
F I L E M AN AGE .
MENU A L L RE S E T
.
.
.
Display the MOVIE CLIP screen.
.
.
q Press the STATUS button for about 1 seconds to display the TOP MENU screen.
w Turn the SHUTTER dial, move the cursor (t) to MOVIE CLIP and press the
SHUTTER dial.
CAN C E L
.
N
E TWOR K PACK C ONF I G .
MOV I E CL I P .
EX I T
.
● The movie clip list of the latest clip page recorded on the CF memory card
and the still image (starting point) of the latest clip number appear by overlap-
ping.
MOVIE CLIP screen
The clip page in the
MOV I E C L I P
MOVIE CLIP screen dis-
plays 4 lists per page.
.
mc 0 0 0 5 a s f
R / W
Clip number
Date/time
Memo
09 : 0 0 : 00
02 / 03 / 02
.
mc 0 0 0 6 a s f
R / W
When a MOVIE CLIP menu item is se-
lected and the SHUTTER dial is pressed
with no clips recorded on the CF memory
card, “NO CLIP!” will flash for about 3
seconds.
09 : 3 0 : 25
02 / 03 / 02
.
mc 0 0 0 7 a s f
R / W
10 : 1 0 : 55
R / W
02 / 03 / 02
.
mc 0 0 0 8 a s f
Cursor
Latest clip
11 : 0 0 : 00
02 / 03 / 02
PAGE
B
CK
A
If there is no CF memory card inserted,
“NO CF CARD!” will flash for about 3
seconds.
6.
Select the clip to play back.
q Turn the SHUTTER dial and move the cursor (t) to the clip to play back.
● Turning the SHUTTER dial up scrolls to the page with smaller (older) clip
numbers.
● Turning the SHUTTER dial down scrolls to the page with larger (newer) clip
numbers.
● Press the [FF] button to scroll to the next page. Press the [REW] button to
scroll to the previous page.
CLIP FUNCTION screen
● Press and hold the [FF] button for about 2 seconds to scroll to the page with
the newest clip.
MOV I E C L I P
.
mc 0 0 0 8 a s f
R / W
● Press and hold the [REW] button for about 2 seconds to scroll to the page
with the oldest clip.
w Press the SHUTTER dial.
CLIP FUNCTION screen of the selected clip appears.
● Still image (starting point) of the selected clip appears.
REV I E
DE LE T
W
E
P ROT E CT
Note
PAGE
B
CK
A
● ASF files recorded using another device may not play back properly on this unit.
● If recording into the CF card is carried out within 5 seconds, either a file cannot be
made or it becomes difficult to display a thumbnail (a still picture displayed when
CLIP FILE is selected).
Selected clip number Still image (starting point)
of the selected clip
→
OVER
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie clip
Playing back video/audio recorded on a CF memory card
CLIP FUNCTION screen
STATUS
SHUTTER
MOV I E C L I P
.
mc 0 0 0 8 a s f
R / W
SHUTTER
MENU
dial
BLANK SEARCH REW
STOP
FF
PLAY
STILL
REV I E
DE LE T
W
E
OPEN
EDITSEARCH
P ROT E CT
MONITOR
FILTER
3200K
1
2
1
5600K
/
8
ND
64 ND
STATUS
PAGE
B
CK
A
.3 5600K
.4 5600K
1
/
POWER
SUPPLY
SHUTTER
PLAY button
LCD BRIGHT
DISPLAY
ON OFF
MENU
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
BACK
NORMAL
SPOT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
VTR
CH-1
CH-2
REVIEW
L
AUTO
FF button
REW button
CAM
MANUAL
NETWORK
PACK
KA-DV5000
PAGE BACK
POWER
VTR
ON
OFF
MOV I E C L I P
.
mc 0 0 0 8 a s f
R / W
7.
Play back the clip.
P L AY
PAGE
8 5 k
Turn the SHUTTER dial, move the cursor to REVIEW and press the SHUTTERdial.
● The movie clip is played back after the clip no. flashes.The value of the recorded
pixel size (320 × 240 or 160 × 120) appears during displaying the still image.The
value of the recorded max. bit rate appears during playback.
B
CK
A
The BIT RATE used for
recording is displayed.
Memo
8.
9.
To pause playback, press the PLAY button.
● The video encoded by the KA-DV5000
is so designed that it is displayed in a
correct aspect ratio by personal
To resume playback, press the PLAY button once more.
computer monitor. When the CF
10.The following operations are performed when the playback of the selected clip
ends. (When PLAY MODE in the MOVIE CLIP SETUP screen is set to “OFF”)
● When there are no following clips, the unit pauses at the beginning of the current
clip.
played-back video is viewed by video-
out connector output of the GY-DV5000
or observed on a liquid crystal monitor
screen, the aspect ratio may look
different. This is because a simple
output is made on the video for a
personal computer and is therefore
normal and not a malfunction.
● If following clips exist, the clip no. flashes and then playback is performed.
When all remaining clips are played back, the unit pauses at the beginning of the
played back clip.
\ Selecting PAGE BACK during playback or pausing and press the SHUTTER dial
● When PLAY MODE in the MOVIE CLIP
SETUP screen is set to “REPEAT”, re-
will return to the MOVIE CLIP screen.
peat playback is performed. ( page 7)
ꢀ
To move to another clip during playback
● Playback will remain on the current clip
even when the FF button is pressed if the
latest clip is being played back.
\ To move to the next clip during middle of playback or pausing, press the FF
button of GY-DV5000.
● The playback of the current clip stops and the unit pauses at the starting point of the
next clip.
Pressing the FF button again pauses at the starting point of the following the next
clip.
● Pressing the REW button during play back
of the oldest clip will start playback at the
starting point of the that clip.
\ To move to the previous clip during middle of playback or pausing, press the
REW button of GY-DV5000.
● The playback of the current clip stops and the unit pauses at the starting point of
the previous clip.
Pressing the REW button again pauses at the starting point of the clip before the
previous clip.
\ To move to the latest clip during middle of playback or pausing, press the FF
button of GY-DV5000 for more than 2 seconds.
● The unit pauses at the starting point of the latest clip.
To start playback, press the PLAY button.
\ To move to the oldest clip during middle of playback or pausing, press the REW
button of GY-DV5000 for more than 2 seconds.
● The unit pauses at the starting point of the oldest clip.
To start playback, press the PLAY button.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie clip
Protecting a clip file on a CF memory card
Clips recorded on a CF memory card can be protected using the MOVIE CLIP screen.
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
STATUS
button
1
2
3200K
5600K
.3 5600K
.4 5600K
SHUTTER
dial
1
1
/
8
ND
64 ND
STATUS
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
MODE
VTR
CAM
POWER switch
MODE switch
● When executing FORMAT in the MOVIE
CLIP SETUP menu screen, protected
clips will also be deleted.
1.
2.
Insert an already recorded CF memory card.
Turn on the GY-DV5000 and KA-DV5000 power.
C F
Check to see that the
display appears on the LCD screen/viewfinder screen.
● Protected clips will not be deleted even
when executing DELETE ALL in the
MOVIE CLIP SETUP menu screen.
(When the power is turned on,
display will flash during initialization.)
3.
4.
5.
Set the MODE switch to “VTR”. (Light the VTR indicator.)
Make sure GY-DV5000 is not in operation.
TOP MENU screen
Display the MOVIE CLIP screen.
MENU
q Press the STATUS button for about 1 seconds to display the TOP MENU screen.
w Turn the SHUTTER dial, move the cursor (t) to MOVIE CLIP and press the
SHUTTER dial.
AUD I O / V I D EO .
.
LCD / V F .
TC / UB / C L OCK .
OT HERS .
F I L E M AN AGE .
MENU A L L RE S E T
.
.
.
.
● The latest page of the MOVIE CLIP screen appears.
R/W display appears on the right of the clip number.
CAN C E L
.
N
E TWOR K PACK C ONF I G .
MOV I E CL I P .
EX I T
.
6.
7.
Select the clip to protect.
Turn the SHUTTER dial, move the cursor (t) to the clip to protect and press the
SHUTTER dial.
● The CLIP FUNCTION screen of the selected clip appears.
MOVIE CLIP screen
Turn the SHUTTER dial, move the cursor to PROTECT in the CLIP FUNCTION
screen and press the SHUTTER dial.
MOV I E CL I P
.
mc 0 0 0 5 a s f
R / W
09 : 0 0 : 00
02 / 03 / 02
CLIP FUNCTION screen
● The selected clip is protected.
.
mc 0 0 0 6 a s f
R / W
09 : 3 0 : 25
02 / 03 / 02
MOV I E C L I P
The R/W display on the right of the clip
.
mc 0 0 0 7 a s f
R / W
.
mc 0 0 0 5 a s f
R
10 : 1 0 : 55
R / W
02 / 03 / 02
number will change to an R display.
.
mc 0 0 0 8 a s f
11 : 0 0 : 00
02 / 03 / 02
PAGE
B
CK
A
Protected
REV I E
DE LE T
W
E
Clip number
P ROT E CT
PAGE
B
CK
A
8.
To return to the MOVIE CLIP screen after completing setting, select PAGE BACK
and press the SHUTTER dial.
CLIP FUNCTION screen
MOV I E C L I P
.
mc 0 0 0 5 a s f
R / W
\ To cancel the protection, select PROTECT in the CLIP FUNCTION screen and
press the SHUTTER dial.
● The R display will change to an R/W display and the protection on the clip will be
canceled.
REV I E
DE LE T
W
E
P ROT E CT
PAGE
B
CK
A
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie clip
Deleting a clip file on a CF memory card
Clips recorded on a CF memory card can be deleted using the MOVIE CLIP screen.
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
STATUS
button
SHUTTER
dial
1
2
3200K
5600K
.3 5600K
.4 5600K
1
1
/
8
ND
64 ND
STATUS
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
MODE
VTR
CAM
MODE switch
POWER switch
TOP MENU screen
1.
2.
Insert an already recorded CF memory card.
Turn on the GY-DV5000 and KA-DV5000 power.
MENU
AUD I O / V I D EO .
.
LCD / V F .
TC / UB / CL OCK .
OT HERS .
F I L E M AN AGE .
MENU A L L RE S E T
.
C F
Check to see that the
display appears on the LCD screen/viewfinder screen.
.
.
(When the power is turned on,
display will flash during initialization.)
.
CAN C E L
.
N
E TWOR K PACK C ONF I G .
MOV I E CL I P .
EX I T
.
3.
4.
5.
Set the MODE switch to “VTR”. (Light the VTR indicator.)
Make sure GY-DV5000 is not in operation.
Display the MOVIE CLIP screen.
MOVIE CLIP screen
q Press the STATUS button for about 1 seconds to display the TOP MENU screen.
w Turn the SHUTTER dial, move the cursor (t) to MOVIE CLIP and press
the SHUTTER dial.
MOV I E C L I P
.
mc 0 0 0 5 a s f
R / W
09 : 0 0 : 00
02 / 03 / 02
● The latest page of the MOVIE CLIP screen appears.
.
mc 0 0 0 6 a s f
R / W
09 : 3 0 : 25
02 / 03 / 02
.
mc 0 0 0 7 a s f
R / W
6.
Select the clip to delete.
10 : 1 0 : 55
R / W
02 / 03 / 02
.
mc 0 0 0 8 a s f
Turn the SHUTTER dial, move the cursor (t) to the clip to delete and press the
11 : 0 0 : 00
02 / 03 / 02
PAGE
B
CK
SHUTTER dial.
A
● The CLIP FUNCTION screen of the selected clip appears.
7.
8.
Turn the SHUTTER dial, move the cursor to DELETE in the CLIP FUNCTION
screen and press the SHUTTER dial.
CLIP FUNCTION screen
● A “DELETE OK?” confirmation message appears. (Confirmation screen)
MOV I E C L I P
.
mc 0 0 0 8 a s f
R / W
To delete, select YES using the SHUTTER dial and press the SHUTTER dial.
● “DELETE . .” flashes on the screen for about 5 seconds and then the MOVIE
CLIP screen returns. The clip is deleted from the MOVIE CLIP screen.
REV I E
DE LE T
W
E
Memo
P ROT E CT
PAGE
B
CK
A
● Protected clips cannot be deleted even when selecting DELETE.
In this case, “PROTECT!” will flash for about 2 seconds and then CLIP FUNC-
TION screen returns.
Confirmation screen
● After deleting a clip and there are no remaining clips left on the CF memory card,
“NO CLIP!” flashes on the screen for about 3 seconds and then the TOP MENU
screen returns.
MOV I E C L I P
.
mc 0 0 0 8 a s f
R / W
● To delete all clips, use the MOVIE CLIP SET in the NETWORK PACK CONFIG
menu screen. (ꢀ page 22)
DE LE T
OK
E
?
DE LE T
.
.
E
PAGE
B
CK
A
Deleting Flashing display
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie clip
Playing back CF memory card clips on your PC
OPEN
EDITSEARCH
MONITOR
FILTER
1
2
3200K
1
1
5600K
.3 5600K
.4 5600K
/
8
ND
64 ND
STATUS
/
POWER
SUPPLY
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
CF memory
BACK
NORMAL
SPOT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
VTR
CH-1
CH-2
L
AUTO
CAM
MANUAL
CF Card reader
NETWORK
PACK
KA-DV5000
card
POWER
VTR
ON
OFF
* If the PC is equipped with PCMCIA
Clips recorded on a CF memory card can be played back on your PC.
slot(s), CF card reader is not required.
Caution
● Clips recorded on CF memory cards are stored in ASF file format.
● To play back a clip on your PC, Windows Media Player 7.01 is required. (WM9 is not supported.)
* Windows Media Player is compatible with Windows XP or Windows 2000/98(SE)/Me operating system.
* Media Player can be downloaded from the Microsoft Website.
During this time, download the following codec software as well.
The codec software is automatically downloaded when opening the clip file and running Windows Media Player.
• Video codec (decorder) ISO MPEG4
• Audio codec (decorder) G.726
Operation
1. Load data already recorded on a CF memory card to your PC using a CF card reader, etc.
2. Launch Explorer, etc., and open the recorded clip file in ASF format.
● Windows Media Player launches and the clip is played back.
Memo
Video and audio files (clip files) in CF memory cards can be appended to email as attachment files.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
LAN card Sending video using LAN card while recording on a DV cassette tape
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
1
2
3200K
5600K
1
1
/
8
ND
64 ND
STATUS
STATUS button
.3 5600K
.4 5600K
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
OFF ZEBRA
SKIN
AREA
AUTO
WHITE
ON
ACCU
FOCUS
POWER
VTR
ON
OFF
VTR
AUDIO
LEVELE CH-1
5
MODE
VTR
CAM
VTR trigger button
MODE switch
VTR trigger button
POWER switch
LCD screen
1.
2.
Insert a LAN card into the Network Pack.
Turn on the GY-DV5000 and KA-DV5000 power.
e
Check to see that the LAN card display is showing on the LCD screen/viewfinder
screen.
3.
4.
Set the MODE switch to “CAM”. (Light the CAM indicator.)
Insert a recordable DV cassette tape.
● GY-DV5000 will be in the standby mode.
LAN card display
5.
Set the NETWORK PACK CONFIG menu screen.
No LAN card is inserted when the
display
appears. Turn off the power and insert a LAN
card. Then, turn the power back on.
q Set MPEG REC to “TRIG”.
w Set the video/audio compress in the ENCODE SETUP menu screen. ( page 6)
ꢀ
• When playing back video/audio streaming data using Quick Time, set STREAM
TYPE in the ENCODE SETUP menu to “for QT”.
e When completed, press the STATUS button to return to the normal screen.
NETWORK PACK CONFIG
menu screen
6.
When pressing the VTR trigger button of GY-DV5000 while Streamproducer is in
operation*, transmission of video/audio streaming data from the LAN card is started
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI N S E T U P
simultaneously with recording to DV cassette tape.
● The LAN card display on the LCD screen/viewfinder screen will be as follows:
ENCODE S E T U P .
MPEG R EC
.
T R I G
MOV I E
L I
C
P
S E T U P .
.
CANCE L
MENU R ES E T
PAGE CK
ⅷ
: Red display during data transmission.
e
B
A
( WMP u n d e r 8 ) ( C F V i e w e r )
* Perform setting described in “5-2 Operating video from DV camcorder • Trigger
mode function” of network distribution software “Streamproducer” User’s Guide.
7.
To stop transmission or recording, press the VTR trigger button.
● GY-DV5000 will be in the standby mode.
Set to TRIG
ENCODE SETUP menu screen
8.
9.
To resume transmission or recording, press the VTR trigger button once more.
To end, press the VTR trigger button to stop transmission and recording and turn
off the power.
Lastly, remove the LAN card.
Memo
● Streaming data will be sent from the LAN card even when a DV cassette tape is
not inserted.
● When the DV cassette tape reaches the end during recording, the transmission
of streaming data from the LAN card is also stopped.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
LAN card
Sending video using a LAN card (no DV cassette tape recording)
STATUS
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
1
2
3200K
5600K
1
1
/
8
ND
64 ND
STATUS
STATUS button
.3 5600K
.4 5600K
/
POWER
SUPPL
Y
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
MODE
VTR
CAM
MODE switch
VTR trigger button
POWER switch
LCD screen
1.
2.
Insert a LAN card into the Network Pack.
Turn on the GY-DV5000 and KA-DV5000 power.
e
Check to see that the LAN card display is showing on the LCD screen/viewfinder
screen.
3.
4.
Set the MODE switch to “CAM”. (Light the CAM indicator.)
Set the NETWORK PACK CONFIG menu screen.
q Set MPEG REC to “SPLIT”.
w Set the video/audio compress in the ENCODE SETUP menu screen. ( page 6)
LAN card display
ꢀ
• When playing back video/audio streaming data using Quick Time, set STREAM
TYPE in the ENCODE SETUP menu to “for QT”.
e When completed, press the STATUS button to return to the normal screen.
No LAN card is inserted when the
display
appears. Turn off the power and insert a LAN
card. Then, turn the power back on.
5.
When operating Streamproducer and making network connection with KA-DV5000,
sending of streaming video/audio data will start from the LAN card.
NETWORK PACK CONFIG
menu screen
When pressing the VTR trigger button on the side of GY-DV5000, recording to the
HDD will start.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI N S E T U P
● The LAN card display on the LCD screen/viewfinder screen will be as follows:
ENCODE S E T U P .
MPEG R EC
.
S PL I T
ⅷ
: Red display during data transmission.
e
MOV I E
L I
C
P
S E T U P .
.
MENU R ES E T
PAGE CK
CANCE L
* Perform setting described in “5-2 Operating video from DV camcorder • Trigger
B
A
( WMP u n d e r 8 ) ( C F V i e w e r )
mode function” of network distribution software “Streamproducer” User’s Guide.
6.
7.
8.
To stop recording to the HDD, press the VTR trigger button on the side.
Press the VTR trigger button on the side to resume recording to the HDD.
ENCODE SETUP
menu screen
Set to SPLIT
To end operation, stop the transmission by disconnecting the network connection
with KA-DV5000 using Streamproducer, then turn off the power.
Lastly, remove the LAN card.
Memo
● When MPEG REC is set to “SPLIT”, sending is performed only when the VTR
trigger button on the side is pressed.The VTR trigger buttons on the front and on
the lens are disabled.
● Pressing the VTR trigger button on the side does not record the camera image
onto the inserted DV cassette tape.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
LAN card
Sending playback signals of a DV cassette tape using a LAN card
STATUS
BLANK SEARCH REW
STOP
FF
PLAY
STILL
SHUTTER
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
3200K
1
2
SHUTTER STATUS
dial button
1
5600K
.3 5600K
.4 5600K
/
8
ND
64 ND
STATUS
1
/
POWER
SUPPL
Y
SHUTTER
PLAY button
LCD BRIGHT
DISPLAY
ON OFF
POWER SUPPLY
switch
MENU
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
BACK
NORMAL
SPOT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
VTR
CH-1
CH-2
L
AUTO
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
MODE
VTR
CAM
MODE switch
VTR trigger button
POWER switch
LCD screen
1.
Insert a LAN card into the Network Pack.
2.
Turn on the GY-DV5000 and KA-DV5000 power.
e
Check to see that the LAN card display is showing on the LCD screen/viewfinder
screen.
3.
4.
Set the MODE switch to “VTR”. (Light the VTR indicator.)
Insert the recorded DV cassette tape.
LAN card display
No LAN card is inserted when the display
5.
Set the NETWORK PACK CONFIG menu screen.
q Set MPEG REC to “SPLIT”.
w Set the video/audio compression in the ENCODE SETUP menu screen.
appears on. Turn off the power and insert a LAN
card. Then, turn the power back on.
(
page 6)
ꢀ
• When playing back video/audio streaming data using Quick Time, set STREAM
TYPE in the ENCODE SETUP menu to “for QT”.
e When completed with settings, press the STATUS button to return to the normal
screen.
NETWORK PACK CONFIG
menu screen
6.
When operating Streamproducer and making network connection with KA-DV5000,
sending of streaming video/audio data will start from the LAN card.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI N S E T U P
ENCODE S E T U P .
MPEG R EC
.
TR I G
● The LAN card display on the LCD screen/viewfinder screen will be as follows:
MOV I E
L I
C
P
S E T U P .
.
C
MENU R ES E T
PAGE CK
( WMP u n d e r 8 ) ( C F V i e w e r )
ANCE L
ⅷ
: Red display during data transmission.
e
B
A
* Perform setting described in “5-2 Operating video from DV camcorder • Trigger
mode function” of network distribution software “Streamproducer” User’s Guide.
7.
8.
Press the PLAY button of GY-DV5000 to start DV cassette tape playback.
ENCODE SETUP
menu screen
SPLIT
Press the VTR trigger button on the side at the scene to start HDD recording with
Streamproducer.
9.
To stop recording to the HDD, press the VTR trigger button on the side.
10.Press the VTR trigger button on the side to resume recording to the HDD.
11.To end operation, first disconnect the network connection and then turn off the
power. Lastly, remove the LAN card.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
Controlling GY-DV5000/KA-DV5000 via LAN card
With the Network Pack, GY-DV5000/KA-DV5000 can be controlled via LAN.
It is also possible to playback video and audio from KA-DV5000 on your PC in the STREAMCAPTURE screen in realtime (live display)
as well as save data to files. However, note that video and audio from KA-DV5000 can be played back only on one PC at a time.
Peer-to-peer connection that directly connects the unit with a PC is explained here.
● There are the 3 types of users for Web access:
● Users referred as “jvc” (can be changed) that can
perform all operations, “ENCODE” users that can
Set the LAN card
driver by following
the instructions on
view all data but only change the encoding
settings, and “BROWSE” users that can only view
data.
manual provided
by the card
manufacturer.
10/100 BASE-T
cross cable
PC
GY-DV5000
● The default password for each user type is “ka-
dv5k” for “jvc” users, first 4 characters of the
password set for “jvc” users for “ENCODE” users
(default is “ka-d”) and fixed password of “ka-dv”
for “BROWSER” users.
● The following is an explanation when login is made
a user permitted with all operations. In the case of
other users, the OK button and Cancel button will
be disabled even if operations on the screen are
allowed.
OPEN
EDITSEARCH
MONITOR
FILTER
3200K
1
2
5600K
1
/
8
ND
.3 5600K
.4 5600K
1
/64 ND
POWER
SUPPL
Y
STATUS
SHUTTER
MENU
L
C
D
B
R
I
G
H
T
DISPLAY
O
N
O
F
F
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
F
U
L
L
A
U
T
O
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
KA-DV5000
Socket Com: EA2900-117 (USA)
EA2903-162 (Europe)
EA2906-194 (Asia)
(CF memory card adapter (PCMCIA TYPE I/II
specifications)(sold separately) is required for
inserting this card.)
1.
2.
3.
4.
5.
6.
Turn your PC and GY-DV5000 and KA-DV5000 power off.
Insert the PCMCIA LAN card to specify into KA-DV5000.
8.
Input the user ID and password.
q For the user ID, input “jvc” (factory setting).
For the password, input “ka-dv5k” (factory setting) or the
name set in the SERVER SETUP menu screen.
Connect the unit and PC using a 10/100 BASE-T cross cable.
Turn the PC and GY-DV5000 and KA-DV5000 power on.
Insert a recordable DV cassette tape.
(
page 12)
ꢀ
w Check to make sure the inputted user ID and password
are correct and click the OK icon.
(Check “Save password” so that the password does not
need to be inputted for future accesses.)
PC settings
● Set the LAN card driver according to the manual provided
by the card manufacturer.
9.
If the user ID and password are correct, the NETWORK PACK
SETUP screen appears on the PC monitor.
● GY-DV5000/KA-DV5000 settings and operations can be
controlled using the NETWORK PACK SETUP. ( page
32)
● Network settings ( page 14)
ꢀ
q Set the following items in the TCP IP properties:
* DHCP server is not used.
IP address: 192.168.100.101
Subnet mask: 255.255.255.000
w Setting the proxy server.
ꢀ
Caution
● When setting the NETWORK PACK SETUP screen (CAM &
VTR CONTROL, NETWORK SETUP, PORT SETUP or EN-
CODE PARAMETERS) and the same menu screen is dis-
played on the LCD screen or viewfinder of GY-DV5000, val-
ues set in the NETWORK PACK SETUP screen will not ap-
pear on menu screen of the LCD screen or the viewfinder of
GY-DV5000.
The values set in the NETWORK PACK SETUP screen will
appear after the menu screen of GY-DV5000 is closed once
and reopened.
• Set the proxy server using the “LAN SETTINGS” of
Windows.
• When using peer-to-peer communication that directly
connects the PC and KA-DV5000, deselect the “Use a
proxy server” checkbox.
• When the “Use a proxy server” setting must be en-
abled due to a LAN environment (in-company LAN,
etc.), click “Advanced...” and input the IP address of
GY-DV5000 in “Exceptions” of the “Use a proxy server”
setting.
● During camera/VTR control, noise may be heard from the
speakers. However, this is not a malfunction. If the noise be-
comes irritating, open the “Sound & Multimedia” property from
the Windows Control Panel and set the sound of “Windows
Explorer Start Navigation” of “Sound Events” to off.
* For setting details, see Windows’ Help.
(
“About proxy servers,” Page 49)
ꢀ
7.
Launch the browser on your PC and enter 192.168.100.101
(default factory setting) in the address bar and press ENTER.
● A confirmation window for user ID and password appears.
● Check to make sure that NET REMOTE in the OTHERS [1/2]
menu screen of GY-DV5000 is set to “ON”. Camera control
will not be available when NET REMOTE is set to “OFF”.
● Depending on the cache setting of your browser, the param-
eters updated in the Camera menu may not be effective im-
mediately.
Enter Network Password
?
X
Please enter tour authentication information.
OK
Cancel
secured
Resource
User name:
Password:
Save password?
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
NETWORK SETUP screen
Clicking NETWORK SETUP on the left of the Streamcorder screen displays the NETWORK SETUP screen for performing network
related settings.
Screen selection
Clicking the OK icon
will confirm the inputted
setting.
Contact your network administrator for any unclear points concerning network settings.
Item
Setting
Description
Factory setting
Address Setup
MANUAL
DHCP
The address setting mode can be selected.
MANUAL : Select for MANUAL mode.
MANUAL
DHCP
: Select for DHCP mode.
IP Address
The IP address can be set.
192.168.100.101
255.255.255.000
192.168.100.254
none
Subnet Mask
Default Gateway
Host Name
The subnet mask can be set.
The gateway address can be set.
The host name can be set. (Max: 63 alphanumerical characters)
The domain name can be entered. (Max: 63 alphanumerical characters)
The address of the domain name system server can be set.
When selecting Change, settings can be made in the FTP Server
Domain Name
DNS Server
none
0.0.0.0
FTP Server
Account
Account Setup screen. ( page 33)
ꢀ
AD-HOC MODE
IBSS
AHDM
OFF
The AD-HOC mode can be set.
OFF
WLAN Channel
1 CH
WLAN Channel can be set.
10 CH
:
10 CH
:
14 CH
ESS-ID
WEP
When selecting Change, settings can be made in the ESS-ID Setup
screen. (Max: 32 alphanumerical characters) ( page 33)
ꢀ
64 Bit
128 Bit
OFF
WEP is set.
OFF
OFF
WEP Key
LEAP
When selecting Change, settings can be made in the WEP Key Setup
screen. ( page 33)
ꢀ
ON
When set to ON, LEAP Server Account can be set.
OFF
LEAP Server
Accout
When Change is selected, settings can be made in the LEAP Server
Account Setup screen. ( page 33)
ꢀ
Caution
If the IP address is changed in the Streamcorder screen, the unit will automatically jump to the new IP address. However, the
screen may not be displayed correctly depending on the environment. In this case, access by specifying the new IP address using
a browser. ( operation 7. on pages 31)
ꢀ
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
NETWORK SETUP screen
FTP Server Account Setup screen
Factory
Item
Description
setting
User Name
Input the FTP user name.
ftp-user
ka-dv
Old password
New Password
Confirm New
Input the currently used password.
Input the new password.
For confirmation, input the new password
again.
ESS-ID Setup screen
Primary ESS-ID
Factory
setting
Item
Description
Current ESS-ID
New ESS-ID
Input the currently used ESS-ID.
Input the new ESS-ID.
NONE
Confirm New
For confirmation, input the new ESS-ID again.
Secondary ESS-ID
Factory
setting
Item
Description
Current ESS-ID
New ESS-ID
Confirm New
Input the currently used ESS-ID.
Input the new ESS-ID.
NONE
For confirmation, input the new ESS-ID again.
WEP Key Setup screen
Factory
setting
Item
Description
Current Wep Key Input the currently used Wep Key.
New Wep Key
Confirm New
Input the new Wep Key.
For confirmation, input the new Wep Key again.
LEAP Server Account Setup screen
Factory
setting
Item
Description
User Name
Input the LEAP user name.
leap-user
ka-dv-jvc
Old Password
New Password
Confirm New
Input the currently used password.
Input the new password.
For confirmation, input the new password again.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
PORT SETUP screen
Clicking PORT SETUP on the left of the Streamcorder screen displays the PORT SETUP screen for performing port settings.
Screen selection
Input
Clicking the OK icon will confirm
the inputted setting.
Item
Description
The HTTP port for WEB browser can be set. (1 to 32767)
The HTTP port for Media player can be set. (1 to 32767)
Factory setting
HTTP (for WEB Browser)
HTTP (for Media Player)
80
8080
8554
554
RTSP (for Streamproducer) The Streamproducer RTSP port number can be set. (1 ~ 32767)
RTSP (for Quick Time) Quick Time RTSP port number can be set. (1 ~ 32767)
* Changing ports require special knowledge. Always consult the administrator of the connecting network when making changes.
* Do not use the same port numbers for RTSP and HTTP.
Caution
If the port is changed in the Streamcorder screen, the unit will automatically jump to the new port. However, the screen may not be
displayed correctly depending on the environment. In this case, access by specifying the new port using a browser. ( operation 7.
ꢀ
on pages 31)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
CAM & VTR CONTROL screen
When the correct user ID and password are accepted, the following Streamcorder screen appears.
In the CAM & VTR CONTROL screen, camera adjustments of GY-DV5000 and VTR controls can be made.
Screen selection
Setting
Clicking will display the
selected screen.
Select the setting from the
pull-down menu.
Adjustment mode selection
Check the desired
adjustment mode.
Clicking the OK icon will
confirm the inputted
setting.
\ Camera Control
Setting range
● When setting AUTO to ON, items other than LOLUX will not be available.
● When setting BARS to ON, items other than AUTO and LOLUX will not be available.
● When setting GAIN to ALC, IRIS and SHUTTER will not be available.
Setting/description
Item
AUTO
Adjustment mode
ON: Auto mode on. Items other than LOLUX cannot be set.
OFF: Auto mode off
ON: Color bar signals are outputted. Items other than AUTO and LOLUX cannot be set.
OFF: Color bar signals are not outputted.
BARS
FAW: Full white balance mode
WHITE BAL
PRESET: White balance will be in the preset state. (3200K)
MEMORY A, B: White balance setting stored in the GY-DV5000 memory will be used.
Auto iris mode. Iris will be adjusted within the following range:
IRIS
AUTO
[–3, –2, –1, 0, +1, +2, +3]
Manual iris mode. Iris will be adjusted within the following range:
[CLOSE, F16, F11, F8, F5.6, F4, F2.8, F2, OPEN]
MANUAL
Lolux mode
Lolux
GAIN
ON
OFF
ALC (Auto Level Control) mode. IRIS and SHUTTER cannot be set
ALC
Gain can be set within the following range. 0dB is not available.
STEP
[–3dB ~ 18dB]
0dB (Sensitivity is not increased)
0dB
Shutter speed can be set within the following range:
SHUTTER
STEP
U model: [1/7.5, 1/15, 1/30, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000]
E model: [1/6.25, 1/12.5, 1/25, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000/, 1/10000]
Shutter speed will be 1/60 (1/50).
( ): for E model
OFF
V-SCAN
Although this setting can be canceled, future settings of this item will not be allowed.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
\ VTR Control
CAM & VTR CONTROL screen
VTR control icons
Click each button to perform
operation.
\ To control the VTR in the Streamcorder screen, the following menu items of GY-DV5000 must be set in advance.
OTHERS [1/2] menu screen
● Set NET REMOTE in the OTHERS [1/2] menu screen to ON.
When set to OFF, the VTR cannot be controlled from the
O T HE RS [ 1 / 2 ]
OU T PU T CHAR
O F F
Streamcorder screen.
N E T R EMO T E
ON
D V RE C T R I GE R
L ONG PAU S E T I ME
R EM F F / R EW MOD E
S T E P S L OW MODE
N E X T PAGE
O F F
3 0M I N
F F / REW
F RAME
P AGE BAC
K
\ VTR control icon operations by MODE switch settings of GY-DV5000 are as follows:
—: Mode will not change
GY-DV5000 state
Clicking VTR control icon
MODE switch
Previous mode
STOP
FF
REC
REC
—
REW
STOP
—
FF
PLAY
PAUSE/STILL
VTR
REW
FF
PLAY
PLAY
PLAY
—
—
—
REW
STOP
STOP
STOP
STOP
—
—
REW
—
—
FF
—
PLAY
—
REV SEARCH
FWD SEARCH
STILL
—
STILL
STOP
REC
—
—
REW
—
—
FF
—
—
PLAY
—
CAM
REC
—
—
STOP
STOP
—
STBY
—
STBY
REC
—
—
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
ENCODE PARAMETERS screen
Clicking ENCODE PARAMETERS on the left of the Streamcorder screen displays the ENCODE PARAMETERS
screen for performing video/audio compression settings.
Setting
Select the setting from the
pull-down menu.
Screen selection
Click the OK icon to
confirm setting.
Setting range
ⅷindicates default factory setting.
Item
Setting
Description
Frame Size
ⅷ 320 × 240
160 × 120
Sets the video compression size.
320 × 240: Sets the image size to 320 × 240 pixels. (CIF)
160 × 120: Sets the image size to 160 × 120 pixels. (QCIF)
(1/4 image size of CIF.)
Bit Rate
56K (bps)
128K (bps)
256K (bps)
ⅷ 384K (bps)
512K (bps)
Sets the video streaming speed.
Frame Rate
MAX
ⅷ MID
MIN
Sets the frame rate per second. Settings are as shown below.
FRAME SIZE
BIT RATE
FRAME SIZE
BIT RATE
(bps)
320 × 240
160 × 120
320 × 240
160 × 120
(bps)
MAX MID MIN MAX MID MIN
NTSC 15 10 7.5 30 15 10
PAL 12.5 25 12.5 12.5
NTSC 15 10 7.5 30 15 10
MAX MID MIN MAX MID MIN
NTSC 7.5
5
5
1
1
3
1
1
1
15 10 7.5
512K
384K
256K
128K
56K
5
5
PAL
5
3
1
12.5 12.5
10 7.5
5
5
5
NTSC
PAL
PAL
NTSC 15 7.5
PAL 12.5
12.5
5
5
5
5
25 12.5
30 15 7.5
25 12.5
5
12.5
5
5
5
Stream Type
ⅷ For Media
Player
For Quick
Time
Sets the player for stream playback.
Memo
• No sound will be heard when playing back using QuickTime while in the WMP mode.
• No sound will be heard when playing back using Media Player while in the QT mode.
• Set to WMP mode when recording to CF memory card.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
STREAMCAPTURE screen (Playing back video/audio using a PC and saving to file)
Click the characters “STREAMCAPTURE” on the left of the Streamcorder screen to display the Streamcapture screen shown below.
Video and audio sent from KA-DV5000 via LAN can be played back on your PC in the Streamcapture screen or data can be saved to files.
It can be used on a PC that has Streamproducer installed.
* Since video on the STREAMCAPTURE screen is converted video data, images will take more time to appear than the actual video taken with GY-
DV5000.
Video display
The display size can be changed in the
Property dialog box.
(ꢀ page 41)
Status/Time elapsed display
● The current status is displayed.
VIEWING: Video or audio from KA-DV5000 is being
played back in realtime (live display).
CAPTURING: Video or audio is being saved in your PC.
STOP:
Playback is stopped.
WAITING: TRIG recording standby.
Operation buttons –– – Clicking will start operation. When on, the
button will light.
Clicking the button will display the Property
dialog box.
VIEW
Click to play back or stop video/audio from KA-
DV5000 on your PC. (ON when the Streamcapture
screen is opened.)
Video display size and the save destination
folder can be changed. (ꢀ page 41)
CAPTURE
Click to save video or audio to a PC.
Default destination
My Document\Streamcorder (\IPAddress)
Saved file name:
The file name based on the capture start time
will be used.
0 2 0 3 0 4 – 1 5 3 0 0 0 .asf
Year Month Day
Hour Minute Second
CAPTURE-TRIG. Click when saving the video/audio from
KA-DV5000 to your PC when starting recording
with GY-DV5000. (ꢀ page 39)
CAST-CAM Click when sending the video/audio from
KA-DV5000 to another PC. (ꢀ page 39)
CAST-BARS Click when transmitting color bars rather than video
from KA-DV5000. (Video from KA-DV5000 will be
displayed in the video display of the Streamcapture
screen. Color bars will not be displayed.)
CAST-TRIG. Click when sending the video/audio from KA-
DV5000 to another PC when starting recording
with GY-DV5000. (ꢀ page 39)
MUTE
Click to turn on/off the mute setting.
When on, the playback sound will be muted.
→
OVER
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
STREAMCAPTURE screen (Playing back video/audio using a PC and saving to file)
About the Trigger Mode function (TRIG)
The Trigger Mode function can be used to save and transmit video/audio from KA-DV5000 to your PC by synchronizing to the button
operations of GY-DV5000.
NETWORK PACK CONFIG
menu screen
1.
Set MPEG REC in the NETWORK PACK CONFIG menu to
“TRIG” or “SPLIT” using steps 1 ~ 9 of page 8.
● TRIG: Records/transmits video/audio streaming data to
your PC at the same time as the recording to the DV cas-
sette tape set in GY-DV5000.
● SPLIT: Records/transmits video/audio streaming data to
your PC regardless of whether the DV cassette is set.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MA I N S E T UP .
.
ENCODE S E T UP .
MPEG R EC
.
TR I G
MOV I E
L I
C
P
S E T UP .
.
MENU R ES E T
C AN CE L
PAGE
B
CK
A
( WMP u n d e r 8 ) ( CF V i e w e r )
2.
Click the CAPTURE-TRIG./CAST-TRIG. button in the
Streamcapture screen.
● Button lights and the program enters the trigger standby
mode.
Setting
NETWORK MAIN SETUP menu screen
(ꢀ page 10)
Memo
● When the CAPTURE-TRIG. button is on:
Saves the video/audio from KA-DV5000 to your PC by
synchronizing to the button operations of GY-DV5000.
● When the CAST-TRIG. button is on:
Transmits video/audio from KA-DV5000 to another PC
by synchronizing to the button operations of GY-DV5000.
* When saving and transmitting video/audio at the same
time, light both CAPTURE-TRIG. and CAST-TRIG. but-
tons.
3.
4.
Press the VTR trigger button of GY-DV5000.
● When the MPEG REC item is set to “SPLIT”, only the VTR
trigger button on the side panel is effective.
● A red ⅷ
mark appears on the GY-DV5000 LCD screen
e
and recording/sending to the PC starts.
Press the VTR triggerbutton of GY-DV5000 while the red
ⅷ
e
mark is displayed.
● The
mark on the LCD screen of GY-DV5000 turns
e
white and recording/sending to the PC stops.
CAPTURE-TRIG.
button
CAST-TRIG.
button
OPEN
EDITSEARCH
MONITOR
FILTER
3200K
1
2
1
5600K
/
8
ND
64 ND
STATUS
.3 5600K
.4 5600K
1
/
POWER
SUPPL
Y
SHUTTER
LCD BRIGHT
DISPLAY
ON OFF
MENU
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
AUDIO INPUT
CH-2
MODE
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
OFF ZEBRA
SKIN
AREA
AUTO
WHITE
ON
ACCU
FOCUS
POWER
VTR
ON
OFF
VTR
AUDIO
LEVELE CH-1
5
VTR trigger button
<GY-DV5000 front>
VTR trigger switch
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
STREAMCAPTURE screen (Playing back video/audio using a PC and saving to file)
About the Cast function (CAST)
The Cast function can be used to send video/audio from KA-DV5000 to another PC.
<Sending method>
<Receiving sent video>
Display the video to send in the video display window of the
Streamcapture screen and click the CAST-CAM button.
Video sent using the Cast function can be received using Win-
dows Media Player.
1.
Launch Windows Media Player and select [Open URL] from
the [File] menu.
2.
Input the IP address and port number of the PC sending data
using Streamcapture.
CAST-
CAM
CAST-
TRIG.
button button button
CAST-
BARS
* The settings can be checked in "Internet URL" of the Cast
dialog box.
● Internet connection
<Color bar transmission>
When clicking the BARS button, color bars are transmitted rather
than the video from KA-DV5000.
● Video of the receiving side will be displayed with color bars.
(Video from KA-DV5000 will be displayed in the video display of
the Streamcapture screen. Color bars will not be displayed.)
● Click the CAST button to switch back to the transmission of video
from KA-DV5000.
● To stop the transmission of video from KA-DV5000 / color bars,
turn off the CAST-CAM/CAST-BARS button.
● LAN connection
In this case, the connection with the receiving side will be dis-
connected.
<Trigger transmission>
When transmitting video/audio from KA-DV5000 to another PC by
synchronizing to the button operations of GY-DV5000, click the
CAST-TRIG. Button. (ꢀ page 39)
3.
Click OK to view the received video.
Caution
When Windows Media Player is receiving a video being sent,
sometimes the connection with a server can be cut off. In such
a case, press the PLAY button of Windows Media Player again.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Network pack setup
STREAMCAPTURE screen (Playing back video/audio using a PC and saving to file)
Property dialog box
Select the video display size
Select the display size from the pull-
down menu.
Setting range:
● Real size
● Fit to window
Click the OK button to
confirm settings.
Advanced settings dialog box
Save destination folder
The default save destination is as follows:
Set this field when changing the save destina-
tion folder.
My Document\Streamcorder (\IPAddress)
When changing the destination folder, press the
Browse... button and select the desired folder.
The changed destination folder will be the de-
fault folder for future save operations.
Cast dialog box
Click the OK button to confirm
settings.
Port numbers of the network used on the PC side dur-
ing communication with the network pack are set.
RTSP port: used for handling commands. Use [TCP].
RTP port: used for receiving video data. Use [UDP].
Normally, available ports are automatically searched
and set.
If there are restrictions to the port numbers due to the
LAN environment settings of your PC, consult your
network administrator.
Click the OK button to confirm
settings.
When specifying the port numbers for use, check each
checkbox and input the number in the edit box on the
right.
HTTP port
Port number of the network used when sending
video/audio is set. Normally, no user setting is re-
quired.
Max clients
Sent video/audio can be received up to the number
specified in this dialog box.
Copy Internet URL
Copies Internet URL to clipboard
Copy LAN URL
Copies LAN URL to clipboard
Internet/LAN URL
When receiving video/audio, the URL displayed here
in entered in Windows Media Player.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
TOP PAGE can be customized
TOP PAGE can be customized as desired.
TOP PAGE created on a PC is uploaded by FTP.
1.
2.
Set the unit so that NETWORK SETUP can be displayed. (ꢀ page 31)
Create HTML on the PC using a commercially available HTML editor, etc.
Save the created HTML file under the name of “index.html”.
3.
Use a commercially available FTP program on the PC to upload index.html created in step 2 above to KA-DV5000.
FTP program settings (Execute using the set value.)
IP Adress
: 192.168.100.101
Remort Port : 21
USER ID
: ftp-user
PASSWORD : ka-dv
\ It is also possible to upload link pages from index.html, images, etc.
Caution
● Make sure the uploaded files do not exceed 100KB in total.
● The HTML display will fit properly on the screen when creating at a size of about 500 × 360 pixels.
● Once uploaded, the file is overwritten and cannot be reproduced. Download and backup necessary files in the FTP.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Connecting Windows Media Player
Connect the KA-DV5000 to Windows Media Player using the network.
1.
2.
Set STREAM TYPE in the ENCODE SETUP menu to “for WMP”.
Open Windows Media Player.
3.
Select [File] → [Open URL].
The following dialog box will appear.
4.
5.
Set the IP address of the camera.
* → IP address of camera
# → HTTP Port number set in “for Media player”
When completed with setting, select OK to establish connection.
Memo
● WMP for Mac OS not supported.
Use QuickTime Player. (ꢀ page 44)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Connecting Quick Time Player
Connect the KA-DV5000 to QuickTime Player using the network.
1.
2.
Set STREAM TYPE in the ENCODE SETUP menu to “for QT”.
Open Quick Time Player.
3.
Select [File] → [Open URL with New Player].
The following dialog box will appear.
4.
5.
Set the IP address of the camera.
rtsp://***.***.***.***/live.mp4
* → IP address of camera
When completed with setting, select OK to establish connection.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
The network pack firmware version can be updated.
About updating the network pack
For details concerning version update data, visit the JVC homepage.
STATUS
SHUTTER
BLANK SEARCH REW
STOP
FF
PLAY
STILL
MENU
OPEN
EDITSEARCH
MONITOR
FILTER
SHUTTER
dial
1
2
3200K
5600K
.3 5600K
.4 5600K
STATUS
button
1
1
/
8
ND
64 ND
STATUS
/
POWER
SUPPL
Y
POWER SUPPLY
switch
SHUTTER
MENU
LCD BRIGHT
DISPLAY
ON OFF
AUDIO
LEVEL
PULL
OPEN
FRONT
REAR
AUTO IRIS
BACK
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO INPUT
L
STRETCH
NORMAL
COMPRESS
AUDIO SELECT
CH-2
AUTO
VTR
STOP button
NORMAL
SPOT
CH-1
L
CAM
MANUAL
NETWORK
PACK
KA-DV5000
POWER
VTR
ON
OFF
POWER switch
NETWORK PACK CONFIG menu screen
1.
2.
3.
Insert a CF memory card with update data into the slot.
Set the POWER switch of GY-DV5000 or KA-DV5000 to ON.
N ETWORK
A CK
ON I G
P
C
F
NET WORK MAI N S E T U P .
.
ENCODE S E T U P .
MPEG R EC
.
TR I G
CANCE L
Press and hold the STATUS button for at least 1 second to display the TOP MENU
screen.
MOV I E
L I
C
P
S E T U P .
.
MENU R ES E T
UPDAT E
.
.
PAGE
B
CK
A
( WMP u n d e r 8 ) ( C F V i e w e r )
4.
Set the cursor to NETWORK PACK CONFIG and press the SHUTTER dial while
holding the STOP button of the camera.
• The NETWORK PACK CONFIG menu screen added with the UPDATE item
appears.
UPDATE menu screen
5.
6.
7.
Turn the SHUTTER dial, set the cursor to UPDATE and press the SHUTTER dial.
• The UPDATE menu screen appears.
U PDA T E
SOF TWARE UPD AT E
CANCE L
PAGE BACK
Set the cursor to SOFTWARE UPDATE and press the SHUTTER dial.
VXX-XX
• CANCEL display will flash and changes will be allowed.
2003.XX.XX XX:XX:XX
Using the SHUTTER dial, set the display to EXECUTE and press the SHUTTER
dial.
INSERT AN UPDATE CF CARD
• Update will begin and “UPDATE..” will flash on the screen during the process.
8.
When update is completed, the normal screen appears.
Caution:
During update, do not turn the power off or perform menu or camera operations.
Malfunction may occur as a result.
UPDATE menu screen contents ꢀ indicates default settings.
Setting
Item
Description
ꢀCANCEL
NETWORK UPDATE
Set EXECUTE and press the SHUTTER dial to start update.
EXECUTE
PAGE BACK
Press the SHUTTER dial to return to the NETWORK PAC CONFIG menu screen.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Troubleshooting
When there is a system error, network error, unit malfunction, etc., KA-DV5000 displays the error on the GY-DV5000 LCD screen or
viewfinder screen.
Warning display
<LCD screen or viewfinder screen>
Reference
Screen display
Cause
Remedy
page
<File system related>
CF REMAIN 60SEC!
(Flashing for 3 sec.)
Remaining time became less than 60
Stop recording and replace with a new
26
seconds during recording to CF memory CF memory card, or delete files on the
card.
current CF memory card to secure
recording space.
CF REMAIN 30SEC!
CF REMAIN 20SEC!
CF REMAIN 10SEC!
CF FULL!
Remaining time became less than 30
seconds during recording to CF memory
card.
Remaining time became less than 20
seconds during recording to CF memory
card.
Remaining time became less than 10
seconds during recording to CF memory
card.
Remaining time has run out during
(Displayed until CF recording recording to CF memory card.
stops)
CF FULL!
Recording is being attempted on CF
memory card with remaining time of less
than 10 seconds.
(Flashing for 3 sec.)
FORMAT ERROR!
Failed to format CF memory card.
Check the CF memory card and format
again. If the card still cannot be format-
ted, contact your nearest JVC-authorized
service agent.
18
18
NO CF FORMAT!
(Flashing)
CF memory card is unformatted, or an
unknown format is being used.
Check the CF memory card and format.
→
OVER
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Troubleshooting
Reference
page
Screen display
Cause
Remedy
<Operation related>
NO CF CARD!
There is no CF memory card inserted.
Insert a CF memory card.
3
(Flashing for 3 sec.)
PROTECT!
Deletion of a protected clip file was
attempted.
To delete the clip file, remove the
protection.
25
––
11
(Flashing for 3 sec.)
NO CLIP!
There is no CF memory card inserted, of Check the CF memory card.
there is no clip file available.
(Flashing for 3 sec.)
SET WLAN AD HOC MODE
OFF!
Use of DHCP server was attempted
while in the AD HOC mode.
Set DHCP in the NETWORK SET menu
screen to OFF when using the AD HOC
mode.
(Flashing for 3 sec.)
SET DHCP OFF!
Selection of AD HOC mode was at-
tempted while using DHCP server.
Set WLAN AD MOC MODE in the
NETWORK SET menu screen to OFF
when using DHCP server.
11
(Flashing for 3 sec.)
OVERLAP HTTP!
Port set for HTTP for WEB Browser is
already in use.
Set an unused port.
11, 34
(Flashing for 3 sec.)
OVERLAP ASF_HTTP!
(Flashing for 3 sec.)
Port set for HTTP for Media Player is
already in use.
Set an unused port.
11, 34
11, 34
OVERLAP ASF-RTSP!
(Flashing for 3 sec)
Set port for RTSP for Streamproducer is Set an unused port.
already in use by another port.
OVERLAP QT-RTSP!
(Flashing for 3 sec)
Set port for RTSP for Quick time is
already in use by another port.
Set an unused port.
11, 34
ILLEGAL SETTING!
(Flashing for 3 sec.)
Set value exceeded setting range.
Set a value within the setting range.
Set using 10 or 26 characters.
11, 32,
33, 34
DATA LENGTH 10 or 26
(Flashing for 3 sec)
Setting made with other than 10 or 26
characters.
12, 33
12, 33
12, 32
12, 33
––
CHRACTER IS SHORT!!
(Flashing for 3 sec)
Set number of characters is 2 or less / 3
or less.
Set using 3 or more / 4 or more charac-
ters.
SET LEAP MODE OFF!!
(Flashing for 3 sec)
Attempted to use LEAP while in the
ADHOC mode.
Set LEAP to OFF when in the ADHOC
mode.
SAME OLD PASSWORD!!
(Flashing for 3 sec)
The new password is the same as the old Set a password different from the old
password. password.
GARBAGE! (Flashing display Optimization of internal ROM disk currently Please wait until process is completed.
while optimizing)
being processed.
IP ADDRESS ERROR!
Failed to acquire IP address when DHCP Set DHCP again.
11, 32
(Flashing display until network is ON.
connection is established)
NO UPDATE FILES!
(Flashing for 3 sec.)
There is no update data in the CF memory Insert a CF memory card with UPDATE
card.
data into the slot.
NO UPDATE CARD!
(Flashing for 3 sec.)
CF memory card is not inserted.
Insert a CF memory card with UPDATE
data into the slot.
UPDATE FAILED!
Update was not successful.
Contact your JVC dealer.
COPY GUARD!
Signal of recording origin is protected with Input recording signal with no copy guard
copy guard. protection.
––
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Checking communication/connection
By using the PING command standard to Windows, it is possible to check whether the connection is correct and that communication
can be made from the PC to KA-DV5000.
1.
2.
Launch the command prompt.
● For Windows 2000
From the Start button, select [Programs] → [Accessories] → [Command Prompt].
Input the following and press the Enter key.
PING xxx.xxx.xxx.xxx
(xxx.xxx.xxx.xxx is the IP address of the other party)
Input example: When the IP address of the other party is "192.168.0.10"
PING 192.168.0.010
3.
Check to see that the other party is successfully displayed.
If connection is not successful, “Request timed out” or “Destination host unreachable” message will appear.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
● IP address
Terminology
Identification number assigned to each computer that is connected to a network. The address is used for communication between
network devices.
● LAN (Local Area Network)
A network structured within a relatively small range such as in a single building or an office of a company.
● DHCP (Dynamic Host Control Protocol)
Method of automatically assigning IP address within a network. When a computer is connected to a network, the DHCP server
automatically assigns the IP address.
● WAN (Wide Area Network)
A network structured within a wide area such as between the main office of a company and its branch offices. Internet is also
generally referred to as WAN.
● Netmask
An IP address has the following two roles: 1) address for identifying the network, and 2) address for identifying individual computers.
Netmask is a 32-bit value that defines the number of bits of the IP address to use for identifying the network.
● Gateway
Hardware and software that translates different types of protocols when a computer communicates with another computer outside the
network. The gateway IP address is referred to as the gateway address.
● RTP (Realtime Transport Protocol)
Protocol to transmit in realtime digitalized video/audio data via a network.
● RTSP (Real Time Streaming Protocol)
Protocol to control realtime transmission of video/audio data via a network.
● HTTP (Hypertext Transport Protocol)
Protocol used when transferring HTML (Hypertext Markup Language) files between WWW server and browser.
● Protocol
A set rule for a computer or communication device to perform communication over a network, etc.
● IEEE802,11b
International standard for wireless LAN with maximum communication speed of 11Mbps.
● Channel (wireless LAN)
Frequency range used by wireless LAN. The same frequency must be set by two sides for proper communication.
If there is an access point, adapter, etc., using the same band in the proximity, there may be a hindrance in the communication and
may reduce throughput or the quality of communication. When setting, check the settings of surrounding access points, etc., to avoid
doubling.
● ESS-ID (wireless LAN)
Network identification name used by wireless LAN. The name is used to distinguish other wireless LAN devices.
● Ad hoc mode (wireless LAN)
A mode for direct communication without passing through an access point.
● Infrastrucre (wireless LAN)
Form of communication via an access point.
→
OVER
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
● Encryption mode
Terminology
Setting for encrypting the flow of data during wireless communication.
Following settings are available:
None (Open System): No encryption. Setting will be unavailable and throughput will be improved. However, there is the risk of infor-
mation leakage.
40blt WEP:
128blt:
Encryption is performed using 40-blt encryption key.
Encryption is performed using 104-blt + 24-blt (1V) keys. Although throughput will decline compared to Open
System, security of data will be improved.
● Access point (wireless LAN)
Relay point for infrastructure communication. It can also serve as the relay point for cable LAN or wireless LAN.
● ASF (Advanced Streaming Format)
Data streaming format developed by Microsoft Corporation (U.S.) for transmission of video and audio.
● Host name
Name of a device (not limited to a computer but all connection devices with an IP address) on a network.
● Port number
Number used for detecting applications and service during TCP/IP communication.
● TCP/IP
Abbreviation for Transmission Control Protocol/Internet Protocol and is one of the protocols used during network connection.
● UDP
Different from TCP, UDP is a low-level protocol that does not perform receive checks. In some cases, missing and distorted images
may occur due to packet loss.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
\ About IP address
Terminology
Global IP address and local IP address
There are 2 types of IP addresses: “global IP address” and “local IP address”.
Global IP address: Just as different IP addresses are needed on a network, all PCs using the Internet worldwide must use a unique
IP address. This IP address is referred to as “global IP address”.
Normally, the global address is assigned by the IS provider.
Local IP address: In an environment not connected to the Internet (within a household, within a company, etc.), separate IP
addresses can be used freely within a network.
This IP address is referred to as “local IP address”.
IP address classes
IP addresses are categorized into 3 classes depending on the number of PCs structuring a network.
“Class A IP addresses” are used for large-scale networks, “Class B IP addresses” are used for medium-scale networks and “Class C
IP addresses” are used for small-scale networks.
Within a network, all IP addresses must be of the same class. Each IP address is structured by a series of 4 digit numbers separated
by a period. The first number of the IP address indicates the class.
Class indicated here
IP address
xxx.xxx.xxx.xxx
First number of the IP address
Class
Class A
Class B
Class C
Application (number of PCs structuring the network)
For large-scale networks (max. approx. 16 million units)
For medium-scale networks (max. approx. 65,000 units)
For small-scale networks (max. approx. 120 units)
1~127
128~191
192~223
* “224 ~ 255” are normally not used for IP addresses.
For example, a network structured by a few PCs to dozens of PCs would use Class C IP addresses.
Normally, the following special IP addresses are used when structuring a network.
Class
Set IP address
Class A
Class B
Class C
10.0.0.0 ~ 10.255.255.255
172.16.0.0 ~ 172.31.255.255
192.168.0.0 ~ 192.168.255.255
About proxy server
A proxy is a “relay point” for accessing the Internet. When enabling “Use a proxy server”, the proxy server will make access to the
Internet.
Since various access information is cached at this time, downloading will be faster when reloading the same information from the
Internet since the data is loaded from the proxy server.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
VICTOR COMPANY OF JAPAN, LIMITED
is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD.
is a registered trademark in Japan, the U.S.A., the U.K. and many other countries.
© 2002 VICTOR COMPANY OF JAPAN, LIMITED
LST0103-001B
Download from Www.Somanuals.com. All Manuals Search And Download.
|