INSTALL INSTRUCTIONS C-3311-2 & C-3311-18-2
SLIDE-OUT TRUNK TRAY
2006-2008 CHEVROLET IMPALA
TOOLS REQUIRED:
7/16” wrench
Powered drill w/ 3/16” drill bit
Ratcheting wrench
Standard socket set
Screwdriver set
HARDWARE:
QTY DESCRIPTION
PART #
12
16
12
4
4
4
2
1
1
4
¼-20 x ¾” Hex head bolts
¼” Flat washers
¼-20 Serrated nuts
8-32 x 3/8” Machine Screws
8-32 Keps Nuts
¼” x ¾” Hex head lag bolts (only on C-3311-18-2)
Front Mounting Leg
Rear Driver-side bracket
Rear Passenger-side bracket
Mounting plate w/ pem ¼” pem studs (Use 2 on C-3311-18-2)
P.S. Front Mounting Bracket (only on C-3311-18-2)
P.S. Rear Mounting Adapter Bracket (only on C-3311-18-2)
GSM33001
GSM31005
GSM30023
GSM33540
GSM30027
GSM33060-1
CM001390
CM001391
CM001392
CM001393
CM001394
CM93712
1
1
Always!
ꢀ Read all instructions before installing any Havis-Shields Equipment Corp products.
ꢀ Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
ꢀ Use hardware provided with install kit
ꢀ For product support, visit the Install Instructions Section of our website at
SUB ASSEMBLY: (Use Iso views on page #1 & 2 for sub assemblies)
- 1 -
1. Attach forward mounting legs to the slide out tray.
• Attach forward mounting legs with provided 8-32 screws and hex nuts to slide track.
• The front legs will be square to the slide tray.
•
On the front passenger side of the half tray, passenger side front mounting brackets
(CM001394) will attach to the front mounting legs.
2. Attach rear-mounting brackets to the slide out tray.
•
Loosely attached the rear mounting brackets to the “Cradle Bracket” using ¼” x ¾”
hex head bolts, washers and serrated nuts.
•
On the rear passenger side of the half tray, passenger side rear mounting adapter
bracket (CM93712) will attach to the rear mounting brackets.
INSTALLATION:
1. Mount slide tray in vehicle trunk.
• Slide trunk tray into vehicle with the tall front mounting legs in first. Prop up tray in
position using block of wood.
• Once you have the tray square, and pushed to the forward most position in trunk,
attach mounting brackets to vehicle using the supplied mounting plates.
• On the half tray, passenger side, you will bolt the passenger side front mounting
brackets (CM001394) to the vehicle using ¼” x ¾” Hex head lag bolts. (Pre-drill w/
3/16” drill bit)
• Position mounting plates into locations shown in photos #1 and 2.
• Loosely attach front and rear mounting brackets to mounting plates using ¼” serrated
nuts.
• On the passenger side, attach passenger side rear mounting adapter brackets
(CM93712) to vehicle using ¼” x ¾” hex head lag bolts. (Pre-drill w/ 3/16” drill bit)
Forward Mounting Brackets
Rear mounting brackets
Mounting
Plate
Mounting
Plate
- 3 -
C-3311-2^3311-18-2_INST_9-07
• Tighten all loose hardware.
• Be sure tray slides smoothly and locks in the closed position. If the tray does not slide
smooth then most likely the tray is not square or level.
#8 screws &
hex nuts
¼” bolts, washers,
& nuts
Photo #3
- 4 -
C-3311-2^3311-18-2_INST_9-07
|