Haier AU092ABNCA User Manual

AS072AZNBA  
AU072ABNCA  
(HSU-07CG03/R1)  
AS092AMNBA  
AU092ABNCA  
(HSU-09CG03/R1)  
AS122AYNBA  
AU122ABNCA  
(HSU-12CG03/R1)  
AS162ATNBA  
AU162AFNBA  
(HSU-16CG03/R1)  
AS182ASNBA  
AU182AFNDA  
(HSU-18CG03/R1)  
AS222AJNBA  
AU222AHNBA  
(HSU-22CG03/R1)  
Please read this operation manual before using the air conditioner.  
No.0010544375  
Contents  
Cautions  
1-2  
Parts and functions  
Operation  
Maintenance  
Trouble shooting  
3-5  
6-13  
14-16  
17  
Cautions  
The cardboard box may be broken or cut into  
1
20  
07,09,12  
16,18  
22  
Series  
Type  
3G1.5mm2+2x0.75mm2  
3G2.5mm2+3x0.75mm2  
4G1.5mm2  
2
Parts and Functions  
Indoor Unit  
Test running switch(manual)  
Used only for test running in cooling  
when room temp. is below 16oC .  
Don't use it in normal operation.  
Inlet grille  
Emergency switch(manual)  
Used when remote controller is lost or  
defective. Unit will run temporarily.  
Remote signal receiver  
Air filter  
A beeping sound is generated when  
a signal from remote controller is  
received.  
Vertical flap  
Use remote controller to  
adjust up and down air flow.  
(Don't adjust it manually.)  
Timer mode indicator  
Power indicator  
Operation mode indicator  
Lights up when Timer operation  
is selected.  
Lights up when unit starts.  
Lights up during compressor  
running.  
For models:  
AS092AMNBA  
AS122AYNBA  
AS072AZNBA  
(HSU-07CG03/R1)  
(HSU-09CG03/R1) (HSU-12CG03/R1)  
Inlet grille  
Air filter  
Timer mode indicator  
Operation mode indicator  
Power indicator  
Vertical flap  
Use remote controller to  
adjust up and down air flow.  
(Don't adjust it manually.)  
Lights up when unit  
starts.  
Lights up when Timer  
operation is selected.  
Lights up during  
compressor running.  
For models: AS162ATNBA  
AS182ASNBA  
(HSU-16CG03/R1) (HSU-18CG03/R1)  
Inlet grille  
Air filter  
Vertical flap  
Use remote controller to  
adjust up and down air flow.  
(Don't adjust it manually.)  
Signal Receiving Window  
Running Indicator  
Timer Mode Indicator  
Power Indicator  
For models: AS222AJNBA  
(HSU-22CG03/R1)  
3
Operation  
Remote controller's operation  
When in use, put the signal transmission head directly to the  
receiver hole on the indoor unit.  
The distance between the signal transmission head and the  
receiver hole should be within 7m without any obstacle as well.  
Don't throw the controller, prevent it from being damaged.  
When electronic-started type fluorescent lamp or change-over  
type fluorescent lamp or wireless telephone is installed in the  
room, the receiver is apt to be disturbed in receiving the signals  
so the distance to the indoor unit should be shorter.  
SWING  
MODE  
CLOCK  
F
AN  
TIMER  
SLEEP  
RESET  
SET  
CODE  
LOCK  
A
Loading of the battery  
TEMP  
ON  
Load the batteries as illustrated.  
2 R-03 batteries, resetting key (cylinder)  
OFF  
SWING  
FAN  
MODE  
SLEEP  
Remove the battery cover :  
CLOCK  
TIMER  
SET  
Slightly press " " and push down the cover.  
Load the battery :  
LOCK  
RESET CODE  
Be sure that the loading is in line with the " + " / " - " pole request as  
illustrated.  
Put on the cover again  
Confirmation indicator :  
In disorderation, reload the batteries or load the new batteries  
after 6 mins.  
I
T
N
U
L
O
T
R
N
O
C
T
E
O
E
M
WITH  
R
MIXOLD  
USEBA  
AND  
T
1.DONO  
TTERIES  
TYPES  
TTERIES  
T
NEWBA  
2
DONO  
MODEL:YR-H05  
OFDIFFERENT  
OGETHER  
R
E
M
O
T
E
CONTROL  
UNIT  
Y
B
A
T
T
E
R
I
E
S
I
T
Y
T
R
TCORRECTL  
L
A
THE  
THE  
2.INSER  
-
P
O
O)R-03  
T
+
(TW  
E
H
I
N
VE  
1.DO  
N
O
T
MIX  
OLD  
WITH  
3.PLEASEREMO  
BATTERIESWHEN  
TECONTRLLER  
REMO  
NEW  
DO  
BATTERIESAND  
USE  
S
I
X
N
O
T
BATTERIES  
TYPES  
AD  
T
E
R
A
F
OF  
DIFFERENT  
DISORDER,ANDRELO  
Õ
S
E
W
T
E
S
TOGETHER  
N
U
I
N
2.INSER  
(TWO)  
T
CORRECTL  
BATTERIES  
Y
2
M
R-03  
I
N
THE  
+
-
POLARITY  
3.PLEASE  
R
E
M
O
V
E
THE  
THE  
B
A
T
T
E
R
I
E
S
W
H
E
N
REMOTE  
CONTRLLER  
Note :  
DISORDER,AND  
NEWÕS  
RELOAD  
AFTER  
SIX  
MINUTES  
-
Use two new same-typed batteries when loading.  
If the remote controller can't run normally or doesn't work at all,  
use a sharp pointed item to press the reset key.  
+
-
MODEL:YR-H05  
+
Hint :  
Remove the batteries in case unit won't be in usage for a long period.  
If there are any display after taking-out just need to press reset key.  
6
A
TEMP  
ON  
1
OF
3
SWING  
4
MODE  
SLEEP  
2
CLOCK  
TIMER  
SET  
LOCK  
RESET CODE  
9
7
Operation  
COOL and DRY operation  
Recommendations:  
Use COOL in summer.  
Use DRY in spring, autumn and in damp climate.  
(1) Unit start  
Press ON/OFF button, unit starts.  
Previous operation status appears on display. (Not Timer setting)  
Power indicator on indoor unit lights up.  
A
(2) Select operation mode  
Press MODE button. For each press, operation  
mode changes as follows:  
COOL  
AUTO  
DRY  
FAN  
TEMP  
ON  
3
1
OF
Unit will run in operation mode displayed on LCD.  
Stop display at your desired mode.  
G  
4
6
5
MODE  
SLEEP  
2
(3) Select temp. setting  
Press TEMP. button.  
CLOCK  
TIMER  
SET  
Every time the button is pressed, temp. setting increases 1oC  
Every time the button is pressed, temp. setting decreases 1oC  
Unit will start running to reach the temp. setting on LCD.  
LOCK  
RESET CODE  
(4) Fan speed selection  
Press FAN button. For each press, fan speed changes  
as follows:  
HI  
AUTO  
AUTO  
LO  
MED  
COOL operation starts when room  
temp. is higher than temp. setting.  
Ultra-low air flow  
Unit runs at the speed displayed on LCD.  
In DRY mode, when room temp. becomes 2oC higher than Temp. setting+2oC  
Temp. setting  
temp. setting, unit will run intermittently at LO speed  
regardless of FAN setting.  
On reaching temp. setting,unit  
will run in mild DRY mode.  
Hints  
Remote controller can memorize each operation status. When starting it next time,  
just press ON/OFF button and unit will run in previous status.  
8
Operation  
(5) Air flow direction adjustment  
After operation mode is selected, vertical flap will open automatically according to the mode.  
Referring to the Fig.  
COOL  
Level  
About 10o  
Left and right air flow adjustment  
(manual)  
Move the horizontal blade by a knob on air  
conditioner to adjust left and right direction  
referring to Fig.  
Up and down (Use remote controller)  
Press SWING button, vertical flap will move within  
the range shown in the Fig. Press SWING button  
stop it at a fixed position.  
About 10o  
COOL About 45o  
Cautions:  
Cautions:  
It is advisable not to keep vertical flap at  
downward position for a long time in COOL  
or DRY mode, otherwise, condensate  
water might occur.  
When humidity is high, condensate water  
might occur at air outlet if all horizontal  
louvers are adjusted to left or right.  
(6) Unit stop  
Cautions:  
Unit won't restart until 3 minutes have  
elapsed, due to system protection.  
Press ON/OFF button.  
Only time remains on LCD.  
All indicators on indoor unit go out.  
Vertical flap closes automatically.  
Hints  
As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more  
helpful for a better air circulation.  
Be careful not to catch a cold when cold air blows downward.  
It is harmful to your health in summer to go frequently in and out of places where temp.  
difference is above 7oC. Temp. difference of 3-5oC will remove your fatigue.  
More than this, unit's load can be reduced and power consumption cut down as well. So, you'd  
better set a temp. diff of 3-5oC between indoor and outdoor temp. in COOL mode.  
9
Operation  
TIMER operation  
Set Clock correctly before starting Timer operation(referring to page 5)  
You can let unit start or stop automatically at following times: Before you wake up in the  
morning, or get back from outside or after you fall asleep at night.  
TIMER ON/OFF  
(1)After unit start, select your desired operation mode.  
Operation mode will be displayed on LCD.  
A
Power indicator on indoor unit lights up.  
(2)TIMER mode selection  
Press TIMER button to change TIMER mode.  
Every time the button is pressed, display changes as follows:  
blank  
ON  
ON  
OFF  
OFF  
TEMP  
ON  
TIMER ON-OFF  
TIMER ON  
TIMER OFF  
OFF  
1
SWING  
FAN  
Select your desired TIMER mode (TIMER ON or TIMER  
OFF) ON or OFF will flash.  
MODE  
SLEEP  
(3)Timer setting  
Press HOUR  
CLOCK  
TIMER  
SET  
button.  
4
Every time the button is pressed, time increases 10 min.  
If button is kept depressed, time will change quickly.  
Every time the button is pressed, time decreases 10 min.  
If button is kept depressed, time will change quickly. Time  
will be shown on LCD. It can be adjusted within 24 hours.  
3
2
LOCK  
RESET CODE  
(4)Confirming your setting  
After setting correct time, press SET button to confirm, "ON"  
or "OFF" stops flashing  
Time displayed: Unit starts or stops at x hour x min. (TIMER  
ON or TIMER OFF).  
Timer mode indicator on indoor unit lights up.  
To cancel TIMER mode  
Just press TIMER button several times until TIMER mode disappears.  
Hints  
After replacing batteries or a power failure happens, Time setting should be reset.  
Remote controller possesses memory function, when use TIMER mode next time, just  
press SET button after mode selecting if timer setting is the same as previous one.  
10  
Operation  
TIMER ON-OFF  
(1)After unit start, select your desired operation mode  
Operation mode will be displayed on LCD.  
Power indicator on indoor unit lights up.  
(2) Press TIMER button to change TIMER mode.  
Every time the button is pressed, display changes as follows:  
A
blank  
ON  
ON  
OFF  
OFF  
TIMER ON  
TIMER OFF  
TIMER ON-OFF  
Select TIMER ON-OFF. "ON" will flash.  
(3)Time setting for TIMER ON  
TEMP  
ON  
Press HOUR button.  
OFF  
SWING  
FAN  
1
Every time the button is pressed, time increases 10min.  
If button is kept depressed, time will change quickly.  
Every time the button is pressed, time decreases 10min.  
If button is kept depressed, time will change quickly.  
MODE  
SLEEP  
3
4
CLOCK  
TIMER  
SET  
Time will be shown on LCD.  
It can be adjusted within 24 hours.  
AM refer's to morning and PM to afternoon.  
6
5
2
LOCK  
RESET CODE  
(4) Time confirming for TIMER ON  
After time setting, press TIMER button to confirm.  
"ON" stops blinking, While "OFF" starts blinking.  
Time displayed: Unit starts at x hour x min.  
(5)Time setting for TIMER OFF  
After time setting, press SET button to confirm, "OFF" stops flashing.  
Time displayed: Unit stops at X hour X min.  
(6) Time confirming for TIMER OFF  
Follow the same procedures in "Time setting for TIMER ON".  
To cancel TIMER mode  
Just press TIMER button several times until TIMER mode disappears.  
11  
Operation  
A
Comfortable SLEEP  
Before going to bed at night, you can simply press  
the SLEEP button and unit will bring you a sound  
sleep in selected mode.  
TEMP  
ON  
OFF  
SWING  
FAN  
MODE  
SLEEP  
CLOCK  
TIMER  
SET  
LOCK  
RESET CODE  
In COOL ,DRY mode  
One hour after SLEEP mode starts, temp. will  
become 1oC higher than temp. setting. After  
running for another 1 hour, temp. rises by 1oC  
further. Unit will run for 6 hours then stops  
automatically. Temp. is higher than temp.  
setting so that room temp. won't be too low  
for your sleep.(As shown in Fig.1)  
SLEEP operation starts  
SLEEP operation stops  
Approx. 6 hrs  
Rises 1oC  
1 hr  
Rises 1oC  
1 hr  
Note:  
Temp. setting  
Unit stop  
In AUTO mode, unit will run in SLEEP  
function according to operation mode.  
In FAN mode, comfortable sleep is not  
available.  
Fig.1  
12  
Operation  
Emergency operation and test operation  
Emergency Operation:  
Carry out this operation only when the remote controller is defective or lost.  
When the emergency operation switch is pressed, a " Pi " sound starts once, which  
means the start of this operation.  
In this operation, it is not possible to change the  
settings of temperature and air flow speed, it is  
also impossible to do an operation by the timer.  
Follow the requirements below.  
"Pi"!  
Room  
temperature  
Designated  
temperature  
Timer  
mode  
Air flow Operation  
speed  
mode  
More than 23oC  
CONTINUOUS  
26oC  
COOL  
AUTO  
If an air conditioner is a model cooling .  
Cooling when the room temperature at the start of operation is above 23oC.  
Test operation:  
Use this switch in the test operation when the room  
"Pi"! Pi"!  
temperature is less 16 C, do not use it in the normal  
operation.  
Continue to press the test operation switch for more  
than 5 seconds. After you hear the "Pi" sound twice,  
release your finger from the switch, the cooling  
operation starts with the air flow speed setting "Hi".  
Removal of the restriction of emergency or test operation:  
Press once more the emergency operation switch, or manipulate through the remote  
controller, a "Pi" sound causes the restriction of emergency or test operation to be  
removed.  
When the remote controller is manipulated for the removal, then the selected operation  
by the remote controller.  
13  
Maintenance  
Different models have different appearance.  
Cleaning of unit casing  
Cut off power supply  
before cleaning wipe unit casing with soft cloth.  
In case of heavy stain, clean it with neutral detergent.  
squeeze water in the cloth, wipe off the detergent on unit  
casing completely.  
Cleaning of remote controller  
Don't use water to wash unit casing, please use dry cloth.  
Don't use glass cleanner or cloth soaked with chemicals.  
Cleaning of air filter  
Air Filter  
2.Remove air filters  
1.Open inlet grille by pulling it upward.  
Push up the filter's center tab  
slightly until it is caesura of  
the stopper. Remove it by  
pulling down.  
3.Clean the filter  
Use a vacuum  
cleaner to remove  
dust, or wash the  
filter with water.  
After washing,  
4.Attach the filters  
Air Filter  
Attach filter behind the stopper so that  
the " Front " indication is facing to the front. Make sure  
that it is completely behind the stopper, otherwise  
problems might occur.  
dry the filter  
completely in the shade.  
5.Close the inlet grille.  
14  
Maintenance  
Replacement of Electrostatic Filter  
Detach the Air filters.  
1
2
3
Detach the Electrostatic Filters.  
Be careful  
with fins.  
Replace the old filter with  
new one into the frame.  
Pull up the hook to the  
designated direction  
White side should  
be up side.  
Open the frame of the filter.  
4
5
6
Attach the Electrostatic Filters.  
Attach the Air Filters.  
Close the inlet grille.  
Some of the models may not have the frame of the filter.  
If Electrostatic Filter can no longer be used, please buy a new one instead.  
15  
Maintenance  
Better use of air conditioner  
Cleaning of the air filter.  
Proper room temperature.  
Once every  
two weeks  
Proper  
temperature  
Effective use of the timer.  
Closing of doors and windows  
during operation.  
Curtains or blinds  
for windows  
Avoid time-wasteful  
operation  
Never fail to observe the followings  
Do not block the inlet or outlet.  
Do not sprinkle water over the  
unit..  
Do not pull power plug.  
Do not use for other purposes.  
Such as food preservation.  
plant cultivation.or animl  
breeding.  
16  
Trouble shooting  
Before asking for service, check the following first.  
Phenomenon  
Cause or check points  
The system does not restart  
immediately.  
When unit is stopped, it won't restart  
immediately until 3 minutes have elapsed  
to protect the system.  
When the electric plug is pulled out and  
reinserted, the protection circuit will work  
for 3 minutes to protect the air conditioner.  
During unit operation or at stop, a swishing  
or gurgling noise may be heard. At first 2-3  
minutes after unit start, this noise is more  
noticeable. (This noise is generated by  
refrigerant flowing in the system.)  
During unit operation, a cracking noise may  
be heard. This noise is generated by the  
casing expanding or shrinking because of  
temperature changes.  
Noise is heard :  
Normal  
performance  
inspection  
Should there be a big noise from air flow in  
unit operation, air filter may be too dirty.  
This is because the system circulates smells  
from the interior air such as the smell of  
furniture, cigarettes.  
Smells are generated.  
Mist or steam are blown out.  
During COOL or DRY operation, indoor unit  
may blow out mist. This is due to the sudden  
cooling of indoor air.  
Does not work at all.  
Poor cooling  
Is power plug inserted?  
Is there a power failure?  
Is fuse blown out?  
Multiple  
check  
Is the air filter dirty? Normally it should be  
cleaned every 15 days.  
Are there any obstacles before inlet and outlet?  
Is temperature set correctly?  
Are there some doors or windows left open?  
Is there any direct sunlight through the  
window during the cooling operation?(Use  
curtain)  
Are there too much heat sources or too many  
people in the room during cooling operation?  
17  

ALFA OKIPAGE 20 User Manual
Brother FAX 775Si User Manual
Cornelius Nordic CCM2148 User Manual
Danby SPAC5088 User Manual
Graco HARMONY ISPH009AA User Manual
Heat Controller Inc Air Conditioner REG 253J User Manual
HoMedics Percussion Massager PA 5H User Manual
HP Hewlett Packard F2400 User Manual
HP Hewlett Packard Officejet J5780 User Manual
HP Hewlett Packard psc 1310 User Manual