Bracketron MULTI VEHICLE MOUNT MVM 45 05 User Manual

INSTALLATION MANUAL  
FOR  
VOLKSWAGEN - JETTA -1999.5-2005  
VOLKSWAGEN - GOLF -1999.5-2006  
VOLKSWAGEN - GTI - 1999.5-2005.5  
Mount Location: To the right of the radio  
MVM  
Multi Vehicle Mount  
MVM-45-05  
Includes PHS-203 Ultra Slim Swivel  
Thank you for purchasing your new Bracketron MVM Multi Vehicle Mount.  
The Multi Vehicle Mount is an (end user-installer) modifiable professional mounting  
bracket for most all mobile electronics requiring a steady and secure installation in a mo-  
tor vehicle. The MVM installs behind your vehicles dash panel using existing or non-vis-  
ible holes and is designed to cleanly protrude out from your vehicle’s dash panel.  
Before installing, you must take the time to read and understand this installation manual  
and read all the warnings accompanying this product.  
Instructions Include: tools needed for install, directions for dash panel removal, directions  
for modifying the MVM if required.  
You can download this manual and any updates from  
MVM MODIFICATION INSTRUCTIONS  
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••  
PLEASE NOTE  
The Bracketron MVM-45-05 mount is a modifiable mounting bracket. The illustrations on the left show how this mount should  
look during and after the modification steps in order to fit the listed vehicles on the front page of this manual. Many vehicle  
applications may not require any modifications to the mount. If this is the case it will be noted below and there will be no steps  
to follow on this page.  
Before you begin to form your MVM, please make sure it looks exactly  
the way it does in the top picture to the left.  
Picture 1  
6
To begin, use a marking pen to draw the lines on the MVM as  
7
depicted in red in the middle picture to the left. Note: see red  
lines in the middle picture for guidance.  
Use a tin snips to cut along these lines. Then these cuts have been  
8
made completely, continue by bending along the yellow lines as  
depicted in the middle picture. Make this bend a 90° angle. If the  
the bracket gets bent use a small hammer to pound out the imper-  
fections. If the paint chips use some paint to cover up the paint.  
Bend Mount Here  
Picture 2  
Now go back to Step 3 on the previous page to finish installa-  
tion.  
Cut Mount Here  
Picture 3  
Note: The hole pattern on the face of the MVM maybe  
different then what is shown in the pictures.  
Note: Please see page 3 in this manual for PHS-  
203 Ultra Slim Swivel Instructions.  
© Bracketron Inc, 2007 All rights reserved.  
The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor  
do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.  
Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable  
for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.  
Bracketron Inc 5249 West 73rd Street, Suite G, Edina, MN 55439  
tel: 952-746-7775 fax: 1-800-660-1784 toll free: 1-866-237-4443  
PHS-203 ULTRA SLIM SWIVEL INSTRUCTIONS  
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••  
PLEASE READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON MOBILE SOLUTION.  
This Professional Swivel Mount Solution is designed to be mounted to your MVM or any other 4 hole AMPs compatible mounting  
device. The Ultra Slim Swivel is compact with a low profile and is designed to provide adjustability to devices such as Satellite  
Radio Receivers, GPS monitors or Mobile Phones. The Ultra Slim Swivel angles your device for better viewing, tilting approx 15°  
in all directions and swivels 360° degrees for maximum adjustability. All mounting hardware is included in the kit along with our  
AMPs adapter plate to attach devices that support T- Notch mounting.  
PARTS INCLUDED  
1 - Ultra Slim Swivel  
Note: The swivel can be installed before or after the mount is installed  
in the vehicle. Attach the Ultra Slim Swivel to any MVM or CBM Mount or other AMPs  
mounting device by inserting the M4x10 Pan Head screws through the holes on the  
back half of the swivel. Align the screws up with the holes on the mount. Attach the M4  
Nylon Locking Nuts only finger tight. Rotate the front half of the swivel to gain access to  
the M4x10 Pan Head screws. (See Picture 1&2) Tighten all 4 screws with a #2 Phillips  
screwdriver and 9/32” open end wrench.  
1
1 - AMPs Adapter Plate  
4 - M4 x 10 Hex Head  
Screws  
4 - M4 x 10 Pan Head Screws  
4 - M4 x 12 Pan Head Screws  
4 - M4 Hex Head Nuts  
4 - M4 Nylon Locking Nuts  
4 - M4 Star Washers  
Picture 1  
Picture 2  
Picture 3  
Rotate  
Rotate  
Adjust Hold Tension  
Picture 4  
Tighten the center screw to adjust the desired tension of the swivel. (See  
Picture 3) Note: If Swivel becomes loose over time, you can grasp the  
swivel and pull toward you lightly while rotating it clockwise. This will  
tighten the swivel allowing you to create the desired tension needed.  
2
3
For T- Notch Devices  
Attach the AMPs T- Notch Adapter to the front half of the swivel  
using the M4x12 Pan Head screws. Attach the M4 Star Washers and  
M4 Hex Nuts to the screws and tighten the plate down with the #2  
screwdriver and 9/32” open end wrench. Slide your device onto the  
T- notch Adapter plate to secure it to the swivel. (See Pictures 4)  
Picture 5  
For AMPs Devices with Inserts  
Attach your AMPs device using the M4x10 Hex Head screws and M4  
Star Washers. Align the holes on the device with the holes on the front  
half of the swivel. Slide the Star Washers onto the Hex Head screws.  
Insert the screws through the swivel and into your device only finger  
tight. Tighten down the device with the 9/32” open end wrench.  
Your device is now secure to the swivel. (See Pictures 5)  
© Bracketron Inc, 2007 All rights reserved.  
The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor  
do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.  
Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable  
for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.  
Bracketron Inc. 5249 West 73rd Street, Suite G, Edina, MN 55439  
tel: 952-746-7775 fax: 1-800-660-1784 toll free: 1-866-237-4443  

Carrier 39LD User Manual
Carrier EEZ 40MVC User Manual
Century STE 4261 User Manual
Daewoo DPB 280LH User Manual
Datalogic Scanning GRYPHONTM DX30 User Manual
Fujitsu AOU36RC User Manual
GE AZ38H09DAD User Manual
Goodman Mfg ATUF User Manual
Haier Air Conditioner HW 18L3V User Manual
HoMedics Masseur In A Box RMM 300H User Manual