Instruction booklet
TUMBLE DRYER
Contents
GB
GB
Important information, 2
English
Installation, 3-4
Where to put your dryer
Ventilation
Electrical connection
Levelling your dryer
Before you start using your dryer
Dryer description, 5
The front
The back
Control panel
Start and programmes, 6-8
Choosing a programme
Table of programmes
TVF770
Laundry, 9-10
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 11
General safety
Disposal
Saving energy and respecting the environment
Maintenance and Care, 12
Switching off the electricity
Cleaning the filter after each cycle
Check the drum after each cycle
Cleaning the dryer
Troubleshooting, 13
Service, 14
Hotpoint Guarantee, 15
Hotpoint After Sales Service, 16
! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and
should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the
dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.
! Read these instructions carefully; the following pages contain important information on installation and suggestions
on how the appliance works.
This symbol reminds you to read this booklet.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Permanent venting
Where to put your dryer
GB
In conjunction with the vent tube we recommend
using a Wall/Window Vent Kit, available at a retail
location or the nearest Spare Parts Dealer.
G
Place your dryer at a distance from gas ranges,
stoves, heaters, or cook tops because flames can
damage the appliance.
Inf
p
m
tan
G
If you are going to install the
Minimum gap 10mm
Wall mounting
appliance under a work
1. Leave an opening in
the wall to the left of the
dryers proposed position.
2. Keep the tube as short
and straight as possible
to prevent condensed
moisture from backing up
into the dryer.
counter, be sure to leave a
10mm space between the
top and any other objects on
or above the machine and a
15mm space between the
sides and lateral furnishings
t
Minimum gaps
15mm
or walls. This is to ensure
proper air circulation. Make sure that the back
vents are not obstructed.
3. Similarly, the duct in
the wall should slope
downwards towards the
outside.
G
Make sure you put your dryer in an environment
that is not damp and has proper air circulation
throughout, the dryer will not operate efficiently in
an enclosed space or cupboard.
Window mounting
1. With a stacked dryer
the hole in the window
should ideally be made
below the vent.
! We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed
behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the dryer door.
2. The tube should be
kept as short as possible.
Ventilation
The Dryer dries your laundry by drawing in cool, clean
and relatively dry air, heating it, and then distributing it
through the clothes as they are gently tumbled. For
optimum performance, the moist air is then blown out
through a vent tube at the back of the dryer.
When the dryer is in use, there has to be adequate
ventilation to avoid the back flow of gases into the room
from appliances burning other fuels, including open fires.
Depending on how often you use your dryer, it is
essential that areas A and B are checked periodically
to remove lint or debris.
The vent tube adaptor must be fitted securely thus
preventing any humid air from being emitted back into
the room.
! The Dryer should not be pushed so far back that the
tube adaptor is pulled out of position or the tube is
squashed or bent.
Mobile venting
! The tube should be kept clear of the air intake vent
and kinks or ‘U’ bends must be avoided as these will
obstruct the tube or trap condensation.
A vent tube must always be fitted when the dryer is
used in conjunction with Mobile Venting.
The tube must be fitted securely into the back of the
dryer (see Dryer Description). If possible, it is always
best to connect the tube to a permanent
outlet close to the dryer. If permanent installation is
not possible, the dryer will work just as well with the
tube passing through a partly-opened window.
! Ensure that the end of the tube is not directed
toward the air intake vent at the rear of the dryer.
! The vent tube should not exceed 2.4 metres in
length and should be kept free of any possible
accumulation of fluff, lint and water by shaking it out
frequently. Always ensure that the tube is not
squashed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Open window venting
! Do not use extension cords.
GB
The end of the tube
! The power cord must not be bent or squashed.
should be directed
downwards, to prevent
warm moist air from
condensing in the room or
in the dryer.
! The power supply cord should be checked periodically
and replaced by a cord specially prepared for this dryer
and fitted only by authorised technicians (see
Service). New or longer power cords are supplied at
an extra charge by authorised dealers..
! The manufacturer denies any responsibility should
any of these rules not be followed.
! Ensure that the dryer is adequately ventilated and
that the end of the vent tube is not directed towards
the air intake duct.
! If in doubt about any of the above consult a qualified
electrician.
! The vent tube must always be fitted for optimum
performance.
! Make sure that the vent tube and air intake vents are
not obstructed or blocked.
Levelling your dryer
The dryer must be installed level for correct operation.
! The dryer must not recycle exhaust air.
! Misusing a tumble dryer may create a fire hazard.
! Do not discharge exhaust air into a flue which is
used for exhaust fumes from other appliances that
burn gas or other fuels.
! Do not discharge exhaust air into an extraction
system or any duct with an extractor fan. This will
affect the way the thermal controls operate and can
result in a fire hazard.
When you have installed
your dryer in its final
location check that it is
level first side to side,
then front to back.
Electrical connections
If the dryer is not level,
use a wooden block to
support it while adjusting
the two front legs up or
down, until your dryer is
level.
Make sure of the following before you insert the plug
into the the electrical socket:
G
The socket must be grounded.
G
The socket must be able to sustain the machines
maximum power, which is indicated on the rating
label (see Dryer Description).
G
Power voltage must be within the values indicated
on the rating label (see Dryer Description).
Before you start using your dryer
G
The socket must be compatible with the dryers
plug. Should this not be the case, replace the
plug or the socket.
Once you have installed your dryer and before you
use it, clean the inside of the drum to remove any
dust that could have accumulated during transport.
! The dryer must not be installed outdoors, even if the
space is sheltered. It can be very dangerous if it is
exposed to rain or storms.
! Once installed, the dryers electrical wire and plug
must be within easy reach.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer Description
The front
The back
GB
Air Intake Vent
Rating plate
Drum
Control Panel
Inf
I
m
tan
I
Vent Tube fitted here
Model & Serial
numbers
Caution: Hot!
Filter
Control panel
OPTION
Buttons & Lights
PROGRAMMES
Knob
Indicator
Clean Filter
Light
DISPLAY
CHILD LOCK
Button & Light
Progress
Lights
ON/OFF
Button & Light
START/PAUSE
Button & Light
The light is green when the programme is running,
flashing amber if the programme has been paused or
flashing green if on standby waiting to start a programme
(see Start and Programmes).
The ON/OFF button/light
: If the dryer is running
and this button is pressed, the dryer is turned off.
Press again, the dryer restarts. The light signals that
your dryer is in use or ready to select a programme.
The Child Lock button/light: Press and hold this
button after selecting your programme and any options,
this prevents the programme settings from being
changed. When the light is lit the other buttons and
the programme knob are disabled.
The PROGRAMMES knob sets the programme: rotate
it until the indicator is pointing to the programme you want
to select (see Start and Programmes).
The OPTION buttons/lights select available options for
your selected programme. The lights indicate that the
option has been selected. If an option is not available
the buzzer will beep three times (see Start and
Programmes).
Hold the button to cancel and the light will go out.
The Progress lights show you the status of the
programme. As each stage of the programme starts
the corresponding light turns on.
The Start/Pause button/light
starts a selected
The Clean Filter light gives you a reminder before
every programme that it is essential to clean the filter
every time the dryer is used (see Maintenance and Care).
programme. When you press this button there will be
one beep and the progress lights will flash to confirm
the action. When a programme is running, holding this
button in pauses the programme and stops the dryer.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Choosing a programme
your laundry and take out items that are dry while
others continue drying. When you close the door
GB
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
again, press the START/PAUSE button
to resume drying.
in order
3. Open the door and make sure the filter is clean
and in place (see Maintenance).
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
5. If the On/Off light is not lit: Press the ON/OFF
(When the door is opened the START/PAUSE light
will flash Amber, after the door is closed and the
START/PAUSE button pressed, the START/PAUSE
light will stop flashing and show green.)
9. During the last few minutes of Drying Programmes,
before the programme is completed, the final
COOL TUMBLE phase is entered (fabrics are
cooled), this phase should always be allowed to
complete.
button
.
6. Choose a programme by checking the Programmes
Guide (see Programmes) as well as the indications
for each type of fabric (see Laundry).
- select a programme by rotating the PROGRAMMES
knob.
7. Set a delay time and other options if necessary.
8. The START/PAUSE light is flashing green:
10. The buzzer will warn you when the programme is
complete. Open the door, take the laundry out,
clean the filter and replace it (see Maintenance).
If the Post Creasecare Option has been selected
and you do not remove the laundry immediately,
the dryer will tumble occasionally for 10 hours
or until you open the door.
- press the START/PAUSE
button to begin.
The green light stops flashing and the display will
show the estimated time to end.
During the drying programme, you can check on
11. Unplug the dryer.
Note:
This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is detected. Press the ON/OFF button briefly and wait for the
machine to start up again.
Easy Iron Programme
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time.
The cycle relaxes the fibres and makes them easier to iron and fold.
! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results:
1. Do not load more than the maximum capacity.
These numbers refer to the dry weight:
Fabric
Maximum load
2.5kg
2kg
Cotton and Cotton mixtures
Synthetics
Denim
2kg
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put
them away in the closet. Should this not be possible repeat the programme.
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,
and less well on acrylic fibres and on materials such as Tencel®.
Wool Programme
G
This is a programme for tumble dryer safe garments marked with the symbol
It can be used for load sizes up to 1kg (approximately 3 sweaters).
We recommend that garments are turned inside out before drying.
This programme will take about 60 minutes, but may take longer depending on the size and density of the
load and the spin speed used in your washer.
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be
slightly damp. Allow these to dry naturally as over-drying could damage garments.
.
G
G
G
G
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size
and shape.
! This programme is not suitable for Acrylic garments.
The wool drying cycle of this tumble dryer has been approved by The Woolmark Company for the drying of
Woolmark garments labelled as machine wash and tumble dry, provided that the garments are dried according to
instructions on the garment label and those issued by the manufacturer of this tumble dryer (M0615).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Programmes
GB
Inf
I
! If the On/Off light
is not lit; Press the ON/OFF button
and then select programme.
o
tan
What it does...
How to set it...
Note:
Programme
Options available:
Delay Start
1
Dries your clothes on High
heat setting, ready for
wearing.
1. Position the PROGRAMME knob on 1.
Cottons
2. Select any Options, if required.
Pre Care
t
Extra Dry
3. Press the START/PAUSE button
.
Post Care
Options available:
Delay Start
Dries your clothes on High
heat setting, ready for
putting away.
1. Position the PROGRAMME knob on 2.
2
Cottons
2. Select any Options, if required.
Pre Care
3. Press the START/PAUSE button
.
Cupboard Dry
Post Care
Dries your clothes on High
heat setting, ready for
hanging.
1. Position the PROGRAMME knob on 3. Options available:
3
Delay Start
Pre Care
2. Select any Options, if required.
3. Press the START/PAUSE button
Cottons
.
Hanger Dry
Post Care
Dries your clothes on High
heat setting, ready for
ironing.
Options available:
Delay Start
4
1. Position the PROGRAMME knob on 4.
Cottons
2. Select any Options, if required.
Pre Care
Iron Dry
3. Press the START/PAUSE button
.
Post Care
5
Options available:
Delay Start
Dries your clothes on High
heat setting , ready for
putting away.
1. Position the PROGRAMME knob on 5.
Synthetics
2. Select any Options, if required.
Pre Care
Cupboard Dry
3. Press the START/PAUSE button
.
Post Care
6
Dries your bedding and
towels on High heat setting,
ready for putting away.
Options available:
Delay Start
1. Position the PROGRAMME knob on 6.
Bed & Bath
2. Select any Options, if required.
Pre Care
3. Press the START/PAUSE button
.
Post Care
Options available:
Delay Start
7
Dries your clothes on Low
heat setting, ready to be
worn.
1. Position the PROGRAMME knob on 7.
Delicates
2. Select any Options, if required.
Pre Care
3. Press the START/PAUSE button
.
(e.g. Acrylics)
Post Care
Options available:
None
8
Dries your Woollen clothes,
(see previous page).
1. Position the PROGRAMME knob on 8.
Wool
2. Press the START/PAUSE button
.
Options available:
1. Position the PROGRAMME knob on 9.
9
Airs your clothes with cool
air, use also to cool warm
clothes.
None
AIRING
2. Press the START/PAUSE button
.
10
1. Position the PROGRAMME knob on 10. ! This is not a drying
Brief programme
Easy Iron
programme (see previous
page).
2. Press the START/PAUSE button
.
(approximately 10 minutes)
that softens fibres of clothing
that is ready for ironing.
Options available:
None
Timed Drying
1. Position the PROGRAMME knob on
Options available:
Dries wet clothing that you
wish to dry on low heat or
small loads (less than 1kg).
the desired time: 120, 90, 60, 30 or 20.
High Heat
Delay Start
Pre Care
(120, 90, 60,
30 or 20
minutes)
2. Select any Options, if required.
3. Press the START/PAUSE button
.
Can be used with high heat
option if you prefer to use a
timed programme.
Post Care
Consult suggested drying
times (see Laundry).
The last 10 minutes of these
programmes is the Cool
Tumble.
Options available:
1. Position the PROGRAMME knob on 11
Brief programme
(approximately 10 minutes)
that cools fibres or clothing.
11
None
Cool Tumble
2. Press the START/PAUSE button
.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
The Controls
GB
G
G
PROGRAMMES knob
DISPLAY
The display shows either the amount of time delay
remaining or an indication of the amount of time left for
a drying programme.
The delay time is displayed in hours and counts down
each minute.
The time to end is displayed in hours and minutes and
counts down each minute, this includes the cool
tumble phase. When timed programmes are selected
the time displayed throughout the cycle is the actual
time remaining.
! Warning, if after pressing the Start/Pause button
the programme knob position has changed, the new
position will NOT change the programme selected.
To change a selected programme, press the
Start/Pause button
, the light flashes Amber to
indicate the programme is paused. Select the new
programme and any options required, the light will
then flash green. Press the Start/Pause button
again and the new programme will start.
When a sensing programme is selected the time
displayed is an estimate of the time remaining. When
the programme is selected the display shows the time
required to dry a full load, after around 10 minutes the
controller calculates a better estimate of the cycle time.
The colons between the hours and minutes in the
display flash to show that the time is counting down.
When the programme finishes its cool tumble phase
G
OPTION buttons / lights
These buttons are used to customise the selected
programme to your requirements. A programme must
have been selected on the programmes knob before
an option can be selected. Not all options are available
for all programmes (see Start and Programmes). If an
option is not available and you press the button, the
buzzer will beep three times. If the option is available
there will be one beep and the option light next to the
button lights to confirm the selection.
the display will show
.
E88
The display also shows if there is a problem with your
dryer, if this occurs the display will show F followed by
a fault code number (see Troubleshooting).
After the Start/Pause button has been pressed only
the Pre Care and Post Care options can be changed.
Time Delay (Delay Start)
The start of some programmes (see Start and
Programmes) can be delayed for up to 24 hours.
G
Door Opening
Opening the door (or pressing the Start/Pause button
during a programme will stop the dryer and have the
following effects:
)
Press this button, the display shows
and the
OFF
G
The Start/Pause light flashes Amber.
During a delay phase the delay will continue to
option light comes on. Press again and a 1 hour delay
is selected and the display indicates 1hr, each further
press of the button adds 1hr to the delay. When 24hr
G
count down. The Start/Pause button
must be
pressed to resume the delay programme. The
progress lights will change to show current status.
During the drying part of the programme, the
time to end count continues but the colons do not
is displayed a further press the display shows
OFF
G
and after a couple of seconds cancels the delay. You
can also cancel the delay by pressing the On/Off button.
Pre Creasecare (Pre Care)
flash. The Start/Pause button
must be
pressed to resume the programme. The progress
lights will change to show the current status.
During the post creasecare phase of a drying
programme, the programme will finish. Pressing
the Start/Pause button
programme at the beginning.
This option is only available if a delayed start has
been selected. It tumbles the clothes occasionally
during the delayed period to help prevent creases
developing.
G
G
G
will re-start a new
High Heat
Available for Timed Drying programmes. Press this
button and a High Heat setting is selected and the
light next to the button comes on.
Timed programmes have a default of low heat, if the
light next to the button is on then pressing this button
selects a low heat setting and the light goes out.
Post Creasecare (Post Care)
When available and selected, the clothes are
occasionally tumbled after the end of the drying and
cool tumble cycles, to help prevent creases
developing should you not be available to remove the
load immediately the programme is complete.
The Start/Pause button
must be pressed to
resume the programme. The progress lights will
change to show the current status and the
Start/Pause light will stop flashing and turn green.
Changing the Programmes knob will select a new
programme and the Start/Pause light will flash
green. You can use this to select the Cool Tumble
programme to cool the clothes, if you find them
dry enough. Press the Start/Pause button
begin a new programme.
to
G
Note
If you have a power cut, switch off the power or
remove the plug. When the power is restored, press
the Start/Pause button
resume.
and the programme will
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Laundry
Sorting your laundry
Wash Care Labels
GB
G
Check symbols on clothing labels to make sure
that the articles can be tumble dried.
Sort laundry by fabric type.
Empty pockets and check buttons.
Close zippers and hooks and tie loose belts and
strings.
Wring out each item in order to eliminate as much
excess water as possible.
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
Inf
p
o
G
tan
G
G
May be tumble dried
G
Do not tumble dry
t
! Do not load dripping wet clothes into the dryer.
Tumble dry at high heat setting
Tumble dry at low heat setting
Maximum load size
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 7.5kg max (16.5lb)
Synthetic fibres: 3kg max (6.6lb)
Items not suitable for tumble drying
G
Articles that containing rubber or rubber-like
materials or plastic film (pillows, cushions, or PVC
rainwear), any other flammable articles or objects
that contain flammable substances (towels soiled
with hair spray).
Glass fibres (certain types of draperies)
Items which have been dry cleaned
! DO NOT overload the dryer as this could result in
reduced drying performance.
Typical weights
G
G
Note: 1kg = 1000g
(1lb = 16oz)
150g
G
Items with the ITCL Code
(see Special
Clothes
clothing items). These can be cleaned with special
at-home dry cleaning products. Follow instructions
carefully.
Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads etc). These expand
when drying and would prevent airflow through
the dryer.
Blouse
Cotton
(5oz)
Other
Cotton
Other
100g
500g
350g
700g
(3oz)
Dress
(1lb 2oz)
(12oz)
(1lb 6oz)
G
Jeans
10 nappies
Shirt
1000g (2lb 3oz)
Cotton
Other
300g
200g
125g
(10oz)
(7oz)
(4oz)
T-Shirt
Household Items
Duvet cover
(Double)
Cotton
Other
1500g (3lb 5oz)
1000g (2lb 3oz)
Large Tablecloth
Small Tablecloth
Tea Towel
700g
250g
100g
700g
350g
500g
350g
(1lb 6oz)
(9oz)
(3oz)
Bath Towel
(1lb 6oz)
(12oz)
Hand Towel
Double Sheet
Single Sheet
(1lb 2oz)
(12oz)
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and synthetics together.
If this happens simply give them an additional short
period of drying.
G
Note: The last 10 minutes of any time set is the
Cool Tumble, so allow for this when setting the time,
as this period will not dry your laundry.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Laundry
Special clothing items
Times are approximate and can vary depending
upon:
GB
Blankets and Bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special
care on LOW heat setting. Avoid drying for a long
period of time.
G
Amount of water retained in clothes after spin
cycle: towels and delicates retain a lot of water.
G
Fabrics: items that are the same type of fabric but
Pleated or creased garments: read the manufacturer’s
drying instructions on the garment.
different textures and thicknesses may not have
the same drying time.
G
Starched articles: do not dry these with non-starched
items. Make sure that as much of the starch solution is
removed from the load as possible before placing it in
the dryer. Do not over-dry: the starch will become
powdery and leave your clothing limp, which defeats
the purpose of starch.
Quantity of laundry: single items or small loads
may take longer to dry.
G
Dryness: If you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
G
Heat setting.
Drying times
G
Room temperature: if the room where the dryer is
The table below presents APPROXIMATE drying times
in minutes. Weights refer to dry garments:
located is cold, it will take longer for the dryer to
dry your clothes.
G
Bulk: some bulky items can be tumble dried with
Cottons
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
High (full) Heat
Drying times 800-1000rpm in washing machine
Half Load
Full Load
1kg 2kg 3kg
4kg
5kg
6kg
7-7.5kg
! Do not over-dry your clothes.
20-30 35-45 45-60 60-70 70-80 80-100 90-130
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
Synthetics
High (full) Heat
Drying times on reduced spin in washing machine
Half Load
Full Load
1kg
2kg
3kg
20-40
30-50
40-70
Delicates (e.g.Acrylics)
Low (gentle) Heat
Drying times on reduced spin in washing machine
Half Load
Full Load
1kg
2kg
50-70
90-130
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings and Suggestions
G
Do not tumble dry large, very bulky items.
! The appliance has been designed and built according
to international safety standards.
These warnings are given for safety reasons and must
be followed carefully.
GB
G
G
Do not tumble dry acrylic fibres at high temperatures.
Remove all objects from pockets, especially lighters
(risk of explosion).
Complete each programme with its Cool Tumble Phase.
Do not turn off the dryer when there are still warm
items inside.
Clean the filter after each use (see Maintenance).
Do not allow lint to collect around the dryer.
Never climb on top of the dryer. It could result in
damage.
Always follow electrical standards and requirements
(see Installation).
Inf
I
m
G
G
tan
General safety
G
G
G
G
This tumble dryer is not intended for use by
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
I
G
G
G
Always buy original spare parts and accessories
(see Service).
This tumble dryer has been designed for home,
and not professional use.
Do not touch the appliance while barefoot or with
G
! WARNING: Never stop the dryer before the end of the
drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.
wet hands or feet.
Unplug the machine by pulling on the plug, not
G
the cord.
G
Recycling and disposal information
As part of our continued commitment to helping the
environment, we reserve the right to use quality recycled
components to keep down customer costs and minimise
material wastage.
Children must not be in proximity of the dryer
when in use. After using the dryer, turn it off and
unplug it. Keep the door closed to make sure that
children do not use it as a toy.
Children should be supervised to ensure that they
do not play with the dryer.
G
G
Disposing of the packaging material: follow local
G
regulations, so the packaging can be recycled.
To minimise risk of injury to children, remove the
The appliance must be installed correctly and
G
have proper ventilation. The air intake vents
behind the machine, the outlet vents and the vent
tube should never be obstructed (see Installation).
Never direct the vent tube outlet towards the air
intake at the back of the machine.
Never allow the tumble dryer to recycle exhaust air.
Never use the dryer on carpeting where the pile
height would prevent air from entering the dryer
from the base.
Check to see if the dryer is empty before loading it.
The back of the dryer could become very
hot. Never touch it while in use.
Do not use the dryer unless the filter is securely
in place (see Maintenance).
door and plug - then cut off mains cable, flush
with the appliance. Dispose of these parts separately
to ensure that the appliance can no longer be
plugged into a mains socket.
G
G
G
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials
they contain and reduce the impact on human health
and the environment.
G
G
G
G
Do not use liquid fabric softeners in the dryer, add
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
it to the final rinse of your wash.
Do not overload the dryer (see Laundry) for
maximum loads.
Do not load items that are dripping wet.
G
G
G
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
Tumble dry items only if they have been washed
with detergent and water, rinsed and been through
the spin cycle. It is a fire hazard to dry items that
HAVE NOT been washed with water.
Carefully check all instructions on clothing labels
(see Laundry).
G
Saving energy and respecting the
environment
G
G
Wring out items to eliminate excess water before
Do not dry garments that have been treated with
tumble drying (if you use a washing machine first,
select a high spin cycle). Doing this will save time
and energy during drying.
Always dry full loads - you save energy: single
items or small loads take longer to dry.
Clean the filter after each use to contain energy
consumption costs (see Maintenance).
chemical products.
Never dry articles that are contaminated with
flammable substances (cooking oil, acetone, alcohol,
petrol, kerosene, spot removers, turpentine, waxes,
wax removers and hair sprays), unless washed in
hot water with an extra amount of detergent.
G
G
G
G
Do not tumble dry rubber, rubber backed articles and
clothes, pillows fitted with foam rubber pads, foam
(latex foam), rubber, plastic, shower caps, waterproof
textiles, nappy pants or liners, polythene or paper.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Switching off the electricity
Check the drum after each cycle
GB
Unplug your dryer when not using it, when cleaning it
and during all maintenance operations.
Turn the drum manually in order to remove small items
(handkerchiefs) that could have been left behind.
Cleaning the drum
Clean the filter after each cycle
! Do not use abrasives, steel wool or stainless steel
The filter is an important part of your dryer:
cleaning agents to clean the drum.
it accumulates lint and fluff that is formed while drying.
Small items could also become trapped in the filter.
When finished drying, therefore, clean the filter by
rinsing it under running water or with your vacuum
cleaner. Should the filter become clogged up, the airflow
inside the dryer will be seriously compromised: drying
times lengthen and you will consume more energy. It
may also damage your dryer.
A coloured film may start to appear on the stainless
steel drum, this may be caused by a combination of
water and, or cleaning agents such as fabric conditioner
from the wash. This coloured film will not affect the
dryer performance.
Cleaning
The filter is found in front
of the dryer trim
G
External parts in metal or plastic and rubber parts
(see diagram).
can be cleaned with a damp cloth.
G
Periodically check the vent tube and any
permanent venting fixture to make sure that there
has been no accumulation of fluff or lint, and
remove it.
G
Remove lint that collects around the filter and the
outlet vents.
Removing the filter:
1. Pull the plastic grip of
the filter upwards (see
diagram).
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
2. Clean the filter and
replace it correctly.
Ensure the filter is fully
located flush into the
tumble dryer trim.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
! Do not use the dryer without replacing the filter..
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
GB
Inf
Problem:
Possible causes / Solution:
I
o
G
The tumble dryer won’t start.
The plug is not plugged into the socket, or not making contact.
There has been a power failure.
The fuse has blown. Try to plug another appliance into the socket.
You are using an extension cord? Try to plug the dryer’s power cord
tan
G
G
G
directly into the socket.
I
G
The door is not closed securely?
The PROGRAMMES knob has not been set properly (see Start and
G
Programmes).
G
The START/PAUSE button has not been pressed (see Start and
Programmes).
G
Drying cycle will not begin.
Its taking a long time to dry.
You have set a delayed time (see Start and Programmes).
G
The filter has not been cleaned (see Maintenance).
The correct programme has not been selected for the load (see Start
G
and Programmes).
The flexible vent tube is obstructed (see Installation).
The air intake vent is obstructed (see Installation).
The permanent ventilation flap on the storm cover is obstructed (see
G
G
G
Installation).
The items were too wet (see Laundry).
The dryer was overloaded (see Laundry).
G
G
Programme finishes and
clothes are damper than
expected.
! For safety the dryer has a maximum programme time of 3 hours. If an
automatic programme has not sensed the required final moisture in this time
the dryer will complete the programme and stop. Check the above points
and run the programme again, if the results are still damp, contact the
Service Centre (see Service).
G
The display shows a fault
code F followed by one or two
numbers.
If the display shows F10 or F15:
- Turn off and remove the plug. Clean the filter (see Maintenance).
Then replace the plug, turn on and start another programme. If F10
or F15 is still displayed contact the Service Centre (see Service).
G
If any other number is shown: Note down the code and contact the
Service Centre (see Service).
G
The display briefly shows
every 6 seconds.
The dryer is in ‘Demo’ mode. Press and hold both the On/Off and
Start/Pause buttons for 3 seconds. The display will show
3 seconds and then the dryer will resume normal operation.
for
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Before calling the Service Centre:
Spare Parts
GB
G
Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
If not, turn off the dryer and call the Service Centre
closest to you.
This dryer is a complex machine. Repairing it yourself
or having a non-authorised person try to repair it could
cause harm to one or more persons, could damage
the machine and could invalidate the spare parts
warranty.
G
Call an authorised technician if you experience problems
while using the machine.
The spare parts have been designed exclusively for
this appliance and not for other uses.
What to tell the Service Centre:
G
name, address and post code.
telephone number.
the type of problem.
the date of purchase.
G
G
G
G
the appliance model (Mod.).
G
the serial number (S/N).
This information can be found on the data label inside
the door of the machine.
Comparative Programmes
G
Programmes recommended for comparative test to EN61121
Programme
(EN61121)
Programme to select
Load size
Dry Cotton
Iron Dry Cotton
Easy-care textile
2 Cottons - Cupboard Dry
4 Cottons - Iron Dry
5 Synthetics - Cupboard Dry
7.5 kg
7.5 kg
3 kg
! Note: This is not a full list of programme options (see Start and Programmes).
This appliance conforms to the following EC Directives:
- 2006/95/EC (Low Voltage Equipment)
- 89/336/EEC, 92/31/EEC and 93/68/EEC (Electromagnetic Compatibility)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of
breakdown repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be
defective because of either workmanship or materials, we will, at our discretion, either
repair or replace the appliance at no cost to you.
The guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
- The appliance is only used on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled or otherwise
interfered with by any person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our
property.
- The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper use, neglect or interference or as a
result of improper installation.
- Replacement of any consumable item or accessory. These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
- Replacement of any removable parts made of glass or plastic.
THE GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN
COMMERCIAL OR NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a FREE 5 year parts guarantee. This additional guarantee is
conditional on you registering your appliance with us and the parts being fitted by one
of our authorised engineers. There will be a charge for our engineer’s time.
To activate the extra parts warranty on your appliance, simply call our registered line on
08448 24 24 24 (Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the
expense of repair bills for the life of your policy. To find the ideal plan for you please call our
advice line on 08448 226 226 (Republic of Ireland 01 230 0233)
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if
you experience any technical difficulties within the first 90 days of ownership. Simply call our
Hotpoint Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone
assistance, or, where necessary, to arrange for an engineer to call.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
195083257. 00 W
01/2010 - SIMLEX . Four Ashes, Wolverhampton
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its
working life than us - the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled
telephone advisors and 1100 fully qualified engineers on call to ensure you receive
fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number
Serial number
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that
protect and hygienically clean your appliance to keep it looking good and functioning
efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your FREE 5 year
parts guarantee you must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Recycling and Disposal Information
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint
reserves the right to use quality, recycled components to keep down customer costs and
minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to
children, remove the door, plug, and cut the mains cable off flush with the appliance. Dispose
of these parts separately to ensure that the appliance can no longer be plugged into a mains
socket and the door cannot be locked shut.
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
Indesit Company, Unit 49 Airways Industrial Estate, Dublin 17
Download from Www.Somanuals.com. All Manuals Search And Download.
|