Please Read
Ikelite Digital Housing
We suggest that you read this instruction booklet thoroughly
before use. If you are new to underwater photography be sure
to read the General and Photo Tips.
i n s t r u c t i o n m a n u a l
#6184.70 for Nikon S700
We also suggest that you read the camera manual thoroughly
to have a full understanding of where each camera control is
located and what function each control provides.
Please Read If Using an EV-Controller
The EV-Controller used with Ikelite DS Substrobes have two
user settings. One setting is for strobe selection, the other is for
This camera uses pre-flash
, thus the
pre-flash or non pre-flash.
EV-Controller should be set to the pre-flash position when used
with this camera.
Congratulations on your purchase of an Ikelite Digital Camera
Housing. Ikelite has over 45 years of experience in the underwater
photographic and lighting market. Our products are designed and
built in the USA by Ikelite for both the professional and amateur
photographer.
The clear housing permits instant visual inspection of the camera
and all sealing surfaces as well as complete monitoring of controls
and camera LCD screens.
Ikelite Digital Housings are slightly negative in salt water for
stability. This housing has been water pressure tested at the
factory. Housing is pressure tested to 200’ (60m).
2
Opening the Housing
One-Touch Portrait
Power
Push Forward
Lock
1. Lid Snaps have a
.
Anti-Shake
To open, push Lid Snap
Lock forward and lift
as shown. Keep
pressure on the Lid
Snap so it does not fly
open quickly.
Lid Snap Lock
Shutter
Release
Lift
Some lid snaps have a lot of spring tension once they go over
center, have a firm grip on the lid snap. Lid Snaps may be
opened one at a time.
Lid
Lid
Snap
Snap
Lens
Port
Installing the
Camera
O' Ring
1. Remove the back
from the housing.
Nikon
Front View
The mounting tray
Lid
Hook
for the camera is
Thumb
Rest
secured to the
housing back.
Position the camera
on the tray and
Zoom
Mounting
Tray
secure it with the
Mounting Bolt
mounting bolt which
Playback
Mode
CAMERA / MOUNT
threads into the
Multi
Selector/OK
camera’s tripod socket.
CAUTION:
Lanyard
Some camera tripod socket threads are plastic. The mounting
tray bolt is metal. Do not cross thread or over tighten as you
may damage the camera tripod socket threads.
2. Pull out on each housing control until it stops. This will get the
controls out of the way for installing the camera.
Menu
Delete
Rotary
Multi
Selector
Back View
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Diffuser and Deflector cont.
A diffuser and deflector are
included with the housing. The
diffuser is white transparent
plastic. The deflector is also
white but is not transparent.
Lens Port
Diffuser/Deflector material
Treat the glass in the lens port as a camera lens. After use, rinse
and gently dry the lens port to avoid water spotting. To clean
use a mild soap solution or lens cleaner.
Do not use alcohol or window cleaner on the Lens Port.
The Lens Port will accept (2) Wide-Angle Adapters. The Wide-
Angle Adapter #9306.80 which is required to mount the Inon
UWL-150AD Bayonet style wide-angle lens. The Wide-Angle
Adapter #9306.81is required to mount the #6420 Ikelite W-20
Wide-Angle Lens and other manufacturers (67mm) screw
thread style wide-angle lenses.
These lenses can be secured onto the Wide-Angle Adapter
above or below water as they are designed to have water
between the front of the port and the accessory lens. Make sure
no air bubbles are trapped between the port and the accessory
lens. Any vignetting that occurs can be eliminated by zooming
the camera lens slightly. The camera’s built-in flash cannot be
used with wide angle
lenses. The front of the
lenses are so large they
block the camera’s flash.
To properly light subjects
when using a wide angle
lens an external strobe
should be used. Due to
the wide-angle of
coverage of these lenses,
the DS125 Substrobe is
recommended or two
DS51Substrobes.
Port Clamp
Spring
To install the diffuser or
deflector spread the port clamp
at the spring end and slide over
the lens port. The white plastic
should be placed in front of the
camera flash. The port clamp
should be pushed back against
the front of the housing.
Spread to Install
Diffuser
The diffuser should be installed when using the camera’s built
in flash. When shooting with the camera’s built-in flash at
approximately 2 feet (0.6 m) or less, the lens port on the
housing may block a portion of the light from the camera’s
built-in flash, creating a shadow in the lower left of the photo.
If this occurs, zoom the lens slightly to eliminate the shadow.
(You can test this above water)
Wide-Angle Adapter
Wide-Angle Lens
Deflector
The deflector should be installed when using an external strobe
such as the DS51or DS125 Substrobe and EV Controller. The
deflector will redirect the camera’s flash to the EV Controller
which controls the external strobes output.
10
9
Optional Accessories
Optional Accessories Continued
Substrobe
DS125
Back o-ring #0109
O-rings last for several years if properly maintained. (See
maintenance) Always carry a spare in case o-ring becomes
damaged or lost.
Substrobe
DS51
Wide-Angle Adapter #9306.80
Required to mount Inon UWL-150AD Bayonet style wide-angle lens.
Wide-Angle Adapter #9306.81
Required to mount Ikelite W-20 and other Screw Thread
(67mm) style wide-angle lenses.
SA-100Q
Arm
SA-100Q
Arm
UR/Pro Filter (Blue Water) #6441.32
The UR/Pro underwater color correcting filter is designed to
restore some of the warm colors filtered out by the water. For
available light use only, not recommended for use with flash.
Green Water Filter #6441.72
Enhances contrast and alters the color of green water to
give our subject a rich, natural tone. For available light
only, not recommended for use with flash.
EV Controller
EV Controller
Tray with Release Handle #9523.31
Tray and Release Handle is required
to mount external Substrobes.
Substrobe DS51
Substrobe DS125
The Substrobe DS51covers the
equivalent of a 28mm lens. It is
the ideal choice when using
only the camera lens or the
camera lens with a macro
accessory lens.
The Substrobe DS125 covers
the equivalent of a 18mm
lens, 100 degrees. It is the
ideal choice when using
accessory wide angle lenses
greater than 28mm.
Ikelite W-20 Wide-Angle Lens #6420
Wide-Angle lenses allow you to capture more of the scene and
get closer to your subject which results in clearer images and
more vivid color. Can be installed or removed underwater for
maximum versatility. (Note: some housings may require an
adapter, see instructions.)
12
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories Continued
Maintenance
The Ikelite Digital Housing should be given the same care and
attention as your other photographic equipment. In addition to
normal maintenance we recommend that the housing be returned
to Ikelite periodically to be checked and pressure tested.
1. Do Not leave the camera and housing in direct sunlight for
prolonged periods. Heat may damage the camera.
2. Do Not ship the camera in the housing.
AF35 Autoflash kit includes:
- AF35 strobe
- Flex arm
3. Before using the housing, always check the tightness of the set
screw in each control knob.
- AutoFlash sensor
- Handle with rubber grip
- Tray (single or dual)
- Mounting hardware
Check each control gland penetrating the housing to make sure
they are tight. There is a slight chance that either could vibrate
loose during travel.
4. Keep the back o-ring clean and lightly lubricated. To lubricate
remove the o-ring from the back. Put a small amount of lkelite
lubricant on your fingers. Draw the o-ring through your fingers
to apply a light coating of lubricant. Only apply enough
lubricant to make the o-ring feel slick. Do Not stretch the
o-ring. This light coating of lubricant will help to keep the
o-ring from drying out and will help to show a dark sealing
line when the housing back is properly sealed.
5. Keep the area where the o-ring fits and the sealing surface of
the housing clean.
6. Rinse the housing exterior thoroughly in fresh water after each
salt water use. Dry with a soft cloth. Dry lens port to eliminate
water spotting.
The Autoflash AF35 replicates your
camera's flash for automatic exposure in
any situation. Single or dual trays can
attach directly to your housing. The
exposure selector dial on the side of the
sensor provides fine tuning to optimize
results with a variety of digital still
cameras. Once you find an exposure level
that you like, leave the dial on that
number for automatic operation.
After several uses in salt water soak the housing exterior in a
mild soap solution, rinse and dry before storage. When storing
the housing, remove the back o-ring, lightly lubricate and place
in a plastic bag. Place the plastic bag with o-ring inside the
housing for safe keeping.
Complete information regarding optional accessories available at
13
14
Control Maintenance
Ikelite controls are designed to provide years of reliable service
with minimal maintenance.
1. Push button controls require no maintenance other than rinsing
in fresh water after saltwater use. If a push button control
becomes difficult to push or if it sticks when depressed, soak the
housing in luke warm fresh water. After a few minutes operate
the push button. If this does not correct the problem, return the
housing to Ikelite for maintenance.
Control Maintenance Cont.
3. Some of the controls have a short shaft and cannot be pulled
out exposing the shaft for lubrication. In the unlikely event one
of these controls sticks or becomes difficult to operate you can
remove the control from the housing and lubricate it, or return
the housing to Ikelite for maintenance. To remove the control,
loosen the set screw in the knob (allen wrench required);
remove the knob. If there is salt or dirt build-up on the exposed
control shaft, clean the shaft. Open the housing and gently slide
the control shaft out of the control gland. Clean and lightly
lubricate the shaft, including the end of the shaft. Slide the
shaft back into the control gland and gently slide it back and
forth a few times without fully removing the shaft from the
gland. Replace the knob, NOTE the flat area on the shaft, the
set screw in the knob should tighten down against the flat area
on the control so the knob does not turn on the shaft.
lubricate shaft
housing
pull out to
expose shaft
housing
gland
control
shaft
2. Some of the controls have long shafts. These controls can be
pulled out, exposing the shaft (see drawing).
To lubricate the control, gently pull on the knob until the
stainless steel shaft is exposed. Lightly lubricate the shaft, then
move the shaft in and out several times. This will lubricate the
x-ring in the Ikelite control gland. This should be done before
using the housing after a prolonged storage period, or once a
week when the housing is in use.
Loosen set screw
(allen wrench required)
Flat
Tighten set screw down
against this area when
replacing the knob.
Lubricate end of shaft
before reinserting into
gland
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
General Tips
Photo Tips
1. Due to the power required to operate the camera, flash, and
LCD screen it is a good idea to start each dive with a fresh set
of batteries.
1. The number one rule in underwater photography is eliminate
as much water between camera and subject as possible. Get
as close as you can to the subject, then use the zoom. If you
are using flash, subjects beyond 6 feet (1.8m)will not have
much color.
2. Some cameras reset their flash to AUTO when the camera is
turned on. If you prefer another setting be sure to select it.
3. As soon as you enter the water, take a moment and check the
housing to see that it is properly sealed.
4. Next, check to see if there are any bubbles on the face of the
lens port. If there are, take your finger and remove them. If
there are bubbles on the lens port they can produce soft focus
spots in your photographs.
2. The camera’s built-in flash is very close to the camera lens. The
flash can light up any suspended particles in the water and they
can be recorded in your picture. This effect is called backscatter.
To eliminate as much backscatter as possible, photograph close.
Photograph in clear water; do not stir up the sand or silty
bottom. If backscatter becomes a problem in the environment
you are photographing, an external flash will help eliminate
much of the backscatter.
3. Digital cameras have a slight lag time between when you press
the shutter release button and the camera actually takes the
picture. Hold the camera steady a second or two after pressing
the shutter release button.
4. Do not shoot down on subjects as they will quite often blend
into the background and be difficult to see in the photograph.
Shoot subjects straight on or shoot up at a slight angle using
the blue water as a contrasting background.
5. Underwater flash is used to restore the warmer colors filtered
out by the water as well as to illuminate the subject. When
photographing underwater, set the camera to use flash on
every shot. If the camera’s flash is set to AUTO and the sun is
behind your subject, the camera may see enough light that it
does not fire the flash. With the sun behind the subject the
subject is shaded (dark) and needs flash for a good exposure.
NOTE
5. If you are shooting with the camera’s built-in flash and the
cameras lens is set to the widest angle you may need to zoom
the lens slightly or a shadow may appear in the lower left
corner of close-up photographs. The lens port may block some
of the light. Installing the flash diffuser will help to eliminate
the shadow. (You can test this above water)
To shoot photographs closer than 2 feet (0.6m), you need to
use an external strobe such as the DS51or DS125. With an
external strobe you can position it so nothing blocks the light
path between the strobe and the subject.
17
18
Photo Tips Cont.
Ikelite Limited Warranty
6. When using daylight or flash if your camera consistently over
or underexposes the image you may want to adjust your
camera’s exposure compensation settings. Many cameras allow
you to adjust both available light and flash exposure with an
EV control in the camera’s menu.
All Ikelite products are warranted against any manufacturing
defects for a period of one year from the date of purchase.
Defective products should be returned prepaid to Ikelite. Ikelite
will, at its discretion, repair or replace such products, and will
return to customer prepaid. All other claims, of any nature,
including but not limited to bulb failure are not covered. Except
as mentioned above, no other warranty expressed or implied,
applies to this Ikelite product.
7. Many photographers transfer their images to the computer
where they can fine tune the appearance of the image. Many
of the image manipulation programs make you think you can
magically correct any image taken and make a good picture.
One thing to remember when using image manipulation
programs, if the image is overexposed much of the color is
missing. If the color is missing you cannot adjust it. If images
are slightly underexposed the color is there, it is just dark and
you can adjust it to some degree. So if you error in exposure it
is better to have the image slightly underexposed than over
exposed.
Returning Products for Service
Ikelite is most interested in preforming any service to assure that
all products perform as intended. For repair or service, return the
product to the address below with your name, address, phone
number and a brief description of the problem. Evidence of
purchase date must be provided to obtain warranty service.
Normal service turnaround time is approximately 2-3weeks.
Ikelite Underwater Systems
50 W 33rd Street
Indianapolis, IN 46208 USA
attn. Repair Dept.
317-923-4523
“repair and service” email: [email protected]
“general questions” e-mail: [email protected]
Digital 6184.70-01-0208
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|