Exmark Lawn Mower Lazer ZHP User Manual

For Serial Nos.  
540,000 & Higher  
Part No. 103-9182  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXMARK PARTS PLUS® PROGRAM  
EFFECTIVE DATE: September 1, 1995  
Program  
If your Exmark dealer does not have the Exmark part in stock,  
Exmark will get the parts to the dealer the next business day or  
the part will be FREE* Guaranteed!!  
How the Program Works  
1.  
If dealer does not have part in stock for a "down" unit at  
the time of request by customer, the dealer contacts his  
distributor by 1:00 p.m., local time, and requests Exmark  
Parts Plus® shipment of six (6) line items or less.  
2.  
Distributor ships part(s) to dealer or customer, as  
requested by dealer, same day, overnight UPS  
Distributor bills dealer for part and freight charges where  
applicable.  
3.  
4.  
5.  
6.  
If distributor does not have the part(s) in stock to satisfy Exmark Parts Plus® order, he contacts Exmark by 3:00 p.m.,  
central time, with an Exmark Parts Plus® order of six (6) line items or less.  
If order is received by 3:00 p.m. central time, Exmark ships part(s) direct to dealer or customer, as requested by  
distributor, same day, overnight UPS, Exmark bills the distributor for parts and shipping charges, where applicable.  
The customer pays for the part and freight if it is shipped under the Exmark Parts Plus® and if it arrives in  
accordance to the program.  
Who pays for the part and freight if it fails to arrive overnight in accordance to the program?  
A. Under any circumstance the customer does not pay.  
B. If the part does not arrive overnight due to:  
1. The dealer not submitting the Exmark Parts Plus® order to his Exmark distributor by 1:00 p.m., the dealer  
pays for the part and freight.  
2. The Distributor being unable to ship the part the same day or not submitting the Exmark Parts Plus® order  
to Exmark by 3:00 p.m., central time, the Distributor pays for the part and freight.  
3. Exmark being unable to ship the part and the Exmark parts order is received by 3:00 p.m., central time,  
Exmark pays for the part and freight.  
4. If the part does not arrive overnight due to the shipper (UPS), the shipper pays for the freight and Exmark  
pays for the part.  
The following restrictions apply -- The Exmark Parts Plus® Program is available only through participating Exmark  
Dealers and applies only to orders submitted on this program Monday through Thursday. Parts Plus service is available  
only in the 48 contiguous United States. UPS has initiated a Saturday delivery program to many areas of the continental  
United States and can be requested for an overnight shipment on Friday to be delivered Saturday. The next day air  
charge, plus the Saturday delivery fee will be the responsibility of the purchaser. Exmark Mfg. will assume no  
responsibility for Saturday delivery shipments. To qualify, all Exmark Parts Plus® orders must be received by Exmark by  
3:00 p.m., central time. Orders must be six (6) line items or less. Exclusions from the Exmark Parts Plus® Program are:  
Any wholegood or accessory in its entirety, engines and engine replacement parts, 5-speed Peerless transmissions and  
5-speed transaxles, hydraulic or hydrostatic wheel motors, cutter decks and engine decks or any item exceeding United  
Parcel Service size and weight restrictions.  
Due to UPS restrictions, aerosol spray paint is considered a hazardous material and cannot be shipped via UPS next day  
or Second Day Air.  
Exmark Manufacturing stocks a limited supply of parts for transaxles, pumps and wheel motors. These parts can be  
ordered for Next Day Air shipment but will not be guaranteed per the Parts Plus Program.  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONGRATULATIONS on the purchase of your Exmark Mower. This product has been  
carefully designed and manufactured to give you a maximum amount of dependability and  
years of trouble-free operation.  
OPERATOR'S MANUAL  
This manual contains assembly, operating, maintenance, adjustment, and safety  
instructions for your Exmark mower.  
BEFORE OPERATING YOUR MOWER, CAREFULLY READ THIS MANUAL IN ITS  
ENTIRETY.  
By following the operating, maintenance, and safety instructions, you will prolong the life  
of your mower, maintain its maximum efficiency, and promote safe operation.  
If additional information is needed, or should you require trained mechanic service,  
contact your authorized Exmark equipment dealer or distributor.  
All Exmark equipment dealers and distributors are kept informed of the latest methods  
of servicing and are equipped to provide prompt and efficient service in the field or at their  
service stations. They carry ample stock of service parts or can secure them promptly for you  
from the factory.  
All Exmark parts are thoroughly tested and inspected before leaving the factory,  
however, attention is required on your part if you are to obtain the fullest measure of  
satisfaction and performance.  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
1. SAFETY  
PAGE  
1.1 Safety Alert Symbol............................................................................1  
1.2 Training ..............................................................................................1  
1.3 Preparation......................................................................................1-3  
1.4 Operation ........................................................................................4-7  
1.5 Maintenance & Storage...................................................................7-8  
1.6 Safety Signs..................................................................................8-10  
2. SPECIFICATIONS  
2.1 Model Numbers................................................................................10  
2.2 Engine..............................................................................................10  
2.3 Fuel System .....................................................................................11  
2.4 Electrical System..............................................................................11  
2.5 Operator Controls.............................................................................11  
2.6 Seat.............................................................................................11-12  
2.7 Hydrostatic Ground Drive System.....................................................12  
2.8 Tires & Wheels.................................................................................12  
2.9 Cutting Deck.....................................................................................12  
2.10 Dimensions.......................................................................................13  
2.11 Torque Requirements.......................................................................13  
3. ASSEMBLY INSTRUCTIONS  
3.1 Uncrate Mower.................................................................................13  
3.2 Install Rollover Protection System (Roll Bar) ...............................13-15  
3.3 Service Battery............................................................................15-16  
3.4 Install Drive Wheels..........................................................................16  
3.5 Check Tire Pressure.........................................................................16  
3.6 Install Seat ..................................................................................16-17  
3.7 Install Motion Control Levers ............................................................17  
3.8 Position Discharge Chute.................................................................17  
3.9 Service Engine .................................................................................17  
3.10 Service Hydraulic Oil ........................................................................18  
4. OPERATION INSTRUCTIONS  
4.1 Controls.......................................................................................18-20  
4.2 Pre-Start...........................................................................................20  
4.3 Mowing........................................................................................20-22  
4.4 Transporting................................................................................22-23  
5. MAINTENANCE & ADJUSTMENTS  
5.1 Periodic Maintenance..................................................................23-32  
5.2 Adjustments ................................................................................32-38  
6. WASTE DISPOSAL  
6.1 Motor Oil Disposal ............................................................................38  
6.2 Battery Disposal ...............................................................................38  
7. TROUBLE SHOOTING ................................................................. 39-40  
8. ELECTRICAL DIAGRAMS..................................................................41-42  
9. HYDRAULIC DIAGRAM ...........................................................................43  
10. WARRANTY.............................................................................................44  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. SAFETY  
1.1 SAFETY ALERT SYMBOL  
This SAFETY ALERT SYMBOL  
is used both in this manual and on the machine to  
identify important safety messages which must be followed to avoid accidents. This  
symbol means:  
ATTENTION! BECOME ALERT!  
YOUR SAFETY IS INVOLVED!  
The safety alert symbol appears above information which alerts you to unsafe actions or  
situations and will be followed by the word DANGER, WARNING, or CAUTION.  
DANGER: White lettering / Red background. Indicates an imminently hazardous situation  
which, if not avoided, WILL result in death or serious injury.  
WARNING: Black lettering / Orange background. Indicates a potentially hazardous  
situation which, if not avoided, COULD result in death or serious injury.  
CAUTION: Black lettering / Yellow background. Indicates a potentially hazardous  
situation which, if not avoided, MAY result in minor or moderate injury.  
1.2 TRAINING  
1.2.1  
Regard the Exmark mower as a piece of power equipment and teach this regard  
to all who operate this unit.  
1.2.2  
Read the instructions carefully. Familiarize yourself with the controls and the  
proper use of the equipment. If the operator(s) or mechanic(s) can not read  
English it is the owner’s responsibility to explain this material to them.  
1.2.3  
1.2.4  
Do not allow operation of this machine by untrained personnel. Never allow  
children, teenagers, or people unfamiliar with these instructions to use the  
mower. Local regulations may restrict the age of the operator.  
Avoid mowing while people, especially children, or pets, are nearby. Keep in  
mind that the operator or user is responsible for accidents or hazards occurring  
to other people or their property.  
1.3 PREPARATION  
1.3.1  
Evaluate the terrain to determine what accessories and attachments are needed  
to properly and safely perform the job. Only use accessories and attachments  
approved by Exmark.  
1.3.2  
The use of personal protective equipment, such as (but not limited to) protection  
for the eyes, ears, feet, and head is recommended.  
CAUTION  
POTENTIAL HAZARD  
This machine produces sound levels in excess of 85  
dBA at the operator’s ear when in operation.  
WHAT CAN HAPPEN  
Exposure to sound levels of 85 dBA or above for  
extended periods of time can cause hearing loss.  
HOW TO AVOID THE HAZARD  
Wear hearing protection when operating this machine.  
1.3.3  
While mowing, always wear substantial footwear and long trousers. Do not  
operate equipment when barefoot or when wearing open sandals.  
- 1 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1.3.4  
Thoroughly inspect the area where the equipment is to be used and remove all  
stones, sticks, wires, bones, and other foreign objects which may damage the  
equipment or cause personal injury to the operator or bystanders.  
WARNING  
POTENTIAL HAZARD  
Engine exhaust contains carbon monoxide, which is  
an odorless deadly poison.  
WHAT CAN HAPPEN  
Carbon monoxide can kill you.  
HOW TO AVOID THE HAZARD  
Do not run engine indoors or in a small confined area  
where dangerous carbon monoxide fumes can collect.  
DANGER  
POTENTIAL HAZARD  
In certain conditions gasoline is extremely flammable  
and highly explosive.  
WHAT CAN HAPPEN  
A fire or explosion from gasoline can burn you, others,  
and cause property damage.  
HOW TO AVOID THE HAZARD  
DO NOT smoke while refueling, and stay away from  
an open flame or where gasoline fumes may be ignited  
by spark.  
Refuel only outdoors.  
Store gasoline in an approved container and keep it  
out of the reach of children.  
Add fuel before starting the engine. Never remove the  
cap of the fuel tank or add fuel when engine is running  
or when the engine is hot.  
Never fill the fuel tank so that the gasoline level rises  
above a level that is 1/2” below the bottom of the filler  
neck to allow for gasoline expansion and prevent fuel  
spillage.  
If fuel is spilled, DO NOT attempt to start the engine.  
Move away from the area of the spill and avoid  
creating any source of ignition until fuel vapors have  
dissipated.  
Don not operate without entire exhaust system in place  
and in proper working condition.  
- 2 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DANGER  
POTENTIAL HAZARD  
In certain conditions gasoline is extremely flammable  
and highly explosive.  
WHAT CAN HAPPEN  
A static charge can ignite gasoline vapors. A fire or  
explosion from gasoline can burn you, others, and  
cause property damage.  
HOW TO AVOID THE HAZARD  
Purchase and store gasoline only in an approved  
container.  
Always place gasoline containers on the ground away  
from your vehicle before filling.  
Do not fill gasoline containers inside a vehicle or on a  
truck or trailer bed because interior carpets or plastic  
truck bed liners may insulate the container and slow  
the loss of any static charge.  
When practical, remove gas-powered equipment from  
the truck or trailer and refuel the equipment with its  
wheels on the ground.  
If this is not possible, then refuel such equipment on a  
truck or trailer from a portable container, rather than  
from a gasoline dispenser nozzle.  
If a gasoline dispenser nozzle must be used, keep the  
nozzle in contact with the rim of the fuel tank or  
container opening at all times until fueling is complete.  
WARNING  
POTENTIAL HAZARD  
Gasoline vapor can collect inside enclosed trailers and  
may be ignited by electrical sparks or hot  
engine/exhaust components.  
WHAT CAN HAPPEN  
Explosion and fire may occur, resulting in property  
damage, personal injury, and/or death.  
HOW TO AVOID THE HAZARD  
Provide adequate ventilation of any enclosed trailer to  
prevent build up of gasoline vapors, especially at floor  
level.  
Refuel only outdoors, never inside an enclosed trailer.  
Be sure all fuel tanks and gasoline storage containers  
have proper caps installed to prevent spillage and  
minimize vapor escaping into the trailer.  
Do not place any equipment that is leaking gasoline in  
an enclosed trailer.  
- 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1.4 OPERATION  
Although hazard control and accident prevention partially are dependent upon the  
design and configuration of the equipment, these factors are also dependent upon  
the awareness, concern, prudence, and proper training of the personnel involved  
in the operation, transport, maintenance, and storage of the equipment. It is  
essential that all Operator Safety Mechanisms be connected and in operating  
condition prior to use for mowing.  
WARNING  
POTENTIAL HAZARD  
Operating engine parts, especially the muffler, become  
extremely hot.  
WHAT CAN HAPPEN  
Severe burns can occur on contact.  
Debris, such as leaves, grass, brush, etc. can catch fire.  
HOW TO AVOID THE HAZARD  
Allow engine parts, especially the muffler, to cool before  
touching.  
Remove accumulated debris from muffler and engine area.  
Install and maintain in working order a spark arrester before  
using equipment on forest-covered, grass-covered, or  
brush-covered unimproved land.  
WARNING  
POTENTIAL HAZARD  
Hands, feet, hair, clothing, or accessories can become  
entangled in rotating parts.  
WHAT CAN HAPPEN  
Contact with rotating parts can cause traumatic amputation  
or severe lacerations.  
HOW TO AVOID THE HAZARD  
Do not operate the machine without guards, shields, and  
safety devices in place and working properly.  
Keep hands, feet, hair, jewelry, or clothing away from  
rotating parts.  
1.4.1  
1.4.2  
Give complete, undivided attention to the job at hand.  
Mow only in daylight or good artificial light, keeping away from holes and hidden  
hazards. NEVER carry passengers.  
DO NOT operate the mower when children or others are in the area!  
1.4.3  
1.4.4  
When feasible, avoid operating the equipment in wet grass.  
Use EXTREME caution when mowing and/or turning on slopes as loss of traction  
and/or tip-over could occur. The operator is responsible for safe operation on  
slopes.  
- 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DANGER  
POTENTIAL HAZARD  
Mowing on wet grass or steep slopes can cause sliding and  
loss of control.  
WHAT CAN HAPPEN  
Wheels dropping over edges, ditches, steep banks, or  
water can cause rollovers, which may result in serious  
injury, death or drowning.  
HOW TO AVOID THE HAZARD  
Do not mow slopes when grass is wet.  
Do not mow near drop-offs or near water.  
Do not mow slopes greater than 15 degrees.  
Reduce speed and use extreme caution on slopes.  
Avoid sudden turns or rapid speed changes.  
See inside the back cover to determine the approximate slope angle of the  
area to be mowed.  
Use a walk behind mower and\or a hand trimmer near drop-offs, ditches, steep  
banks or water. This area can be dangerous, see Figure 1.  
Figure 1  
SAFE ZONE FOR MOWING  
Progressively greater care is needed as the slope increases.  
Always avoid sudden starting or stopping on a slope. If tires lose traction,  
disengage the blades and proceed slowly off the slope.  
Avoid sudden starts when mowing uphill. Mower may tip backwards.  
Be aware that loss of traction may occur going downhill. Weight transfer to  
the front wheels may cause drive wheels to slip and cause loss of braking  
and steering.  
Watch for ditches, holes, rocks, dips, and rises that change the operating  
angle, as rough terrain could overturn the machine.  
Remove or mark obstacles such as rocks, tree limbs, etc. from the mowing  
area. Tall grass can hide obstacles.  
Use extreme care with grass catchers or attachments. These can change the  
stability of the machine and cause loss of control.  
Follow the manufacturer’s recommendations for wheel weights or  
counterweights to improve stability.  
1.4.5  
A Rollover Protection System (roll bar) is installed on the unit.  
- 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
POTENTIAL HAZARD  
There is no rollover protection when the roll bar is down.  
WHAT CAN HAPPEN  
Wheels dropping over edges, ditches, steep banks, or  
water can cause rollovers, which may result in serious  
injury, death or drowning.  
HOW TO AVOID THE HAZARD  
Keep the roll bar in the raised and locked position and use  
seat belt.  
Lower the roll bar only when absolutely necessary.  
Do not wear seat belt when the roll bar is down.  
Drive slowly and carefully.  
Raise the roll bar as soon as clearance permits.  
Be certain that the seat belt can be released quickly if the machine is driven or  
rolls into ponds of water.  
Check carefully for overhead clearances (i.e. branches, doorways, and  
electrical wires) before driving under any objects and do not contact them.  
1.4.6  
1.4.7  
Use EXTREME caution when backing up. LOOK BEHIND YOU!!  
Stop the blades when crossing surfaces other than grass and when transporting  
the mower to and from the area to be mowed.  
1.4.8  
1.4.9  
Never operate the mower with defective guards, shields, or covers. Always have  
safety shields, guards, switches, and other devices in place and in proper  
working condition.  
DO NOT change the engine governor settings or overspeed the engine. Operating  
an engine at excessive speed may increase the hazard of personal injury.  
1.4.10 Disengage PTO before starting engine.  
1.4.11 Start the engine carefully with feet well away from the blades.  
1.4.12 Keep hands, feet, and clothing away from rotating parts while the mower is being  
operated.  
1.4.13 Stop engine, wait for all moving parts to stop, and remove key:  
Before checking, cleaning or working on the mower.  
After striking a foreign object (inspect the mower for damage and make  
repairs before restarting and operating the mower).  
Before clearing blockages.  
Whenever you leave the mower.  
Stop the engine and wait for all moving parts to stop:  
Before refueling.  
Before dumping the grass catcher.  
1.4.14 Before stopping the engine, place the throttle control midway between the “slow”  
and “fast” positions. Allow the engine to run a minimum of 15 seconds; then stop  
the engine.  
1.4.15 The fuel system is provided with a shut-off valve. The fuel shut-off valve is used  
to shut off the fuel:  
When the machine will not be used for a few days.  
During transport to and from the job.  
When parked inside a building.  
- 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1.4.16 This mower was designed for one operator only. Keep all others away from  
mower during operation.  
1.4.17 Do Not mow with the discharge deflector raised, removed, or altered unless  
there is a grass collection system or mulch kit in place and working properly.  
1.4.18 Be aware of the mower discharge and direct discharge away from others.  
1.4.19 Do Not operate the mower under the influence of alcohol or drugs.  
1.4.20 Use extra care when approaching blind corners, shrubs, trees, or other objects  
that may obscure vision.  
1.4.21 If jump starting is required:  
a) connect the positive (+) power cable from the positive post on the booster  
battery to the positive terminal post on the starter solenoid switch (this post  
has the positive battery cable attached to it).  
b) connect the negative or ground cable (-) from the negative post on the  
booster battery to any engine deck ground, preferably the engine block as  
far away from the battery as possible.  
c) disconnect battery cables in the reverse order after starting.  
1.5 MAINTENANCE AND STORAGE  
1.5.1  
1.5.2  
1.5.3  
For engine maintenance, follow the engine manufacturer’s recommendations  
precisely as stated in the engine manual.  
Disconnect the battery cable from the negative battery post when the unit will be  
allowed to sit for more than 30 days without use.  
Allowing batteries to stand for an extended period of time without recharging  
them will result in reduced performance and service life. To preserve optimum  
battery performance and life, recharge batteries in storage when the open circuit  
voltage drops to 12.4 volts.  
Note: To prevent damage due to freezing, battery should be fully charged before  
putting away for winter storage.  
1.5.4  
Keep engine, engine area, and hydraulic pump area free from accumulation of  
grass, leaves, excessive grease, or oil and other debris, which can accumulate in  
these areas. These materials can become combustible and may result in a fire.  
1.5.5  
1.5.6  
Store fuel in a container specifically designed for this purpose in a cool, dry place.  
Keep the mower and fuel container in locked storage to prevent children from  
playing or tampering with them.  
1.5.7  
1.5.8  
1.5.9  
Gasoline powered equipment or fuel containers should not be stored in a basement  
or any enclosed area where open pilot lights or heat appliances are present.  
Maximum mowing results and safety can only be achieved if the mower is  
properly maintained and operated correctly.  
Check all bolts frequently to maintain proper tightness.  
1.5.10 Keep all guards, shields and all safety devices in place and in safe working condition.  
1.5.11 Frequently check for worn or deteriorating components that could create a hazard.  
1.5.12 All replacement parts must be the same as or equivalent to the parts supplied as  
original equipment.  
- 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
POTENTIAL HAZARD  
Hydraulic fluid escaping under pressure can penetrate  
skin and cause injury.  
WHAT CAN HAPPEN  
Fluid accidentally injected into the skin must be  
surgically removed within a few hours by a doctor  
familiar with this form of injury or gangrene may result.  
HOW TO AVOID THE HAZARD  
Make sure all hydraulic fluid hoses and lines are in  
good condition an all hydraulic connections and fittings  
are tight before applying pressure to hydraulic system.  
Keep body and hands away from pinhole leaks or  
nozzles that eject high pressure hydraulic fluid.  
Use cardboard or paper, not your hands, to find  
hydraulic leaks.  
Safely relieve all pressure in the hydraulic system by  
placing the motion control levers in neutral and  
shutting off the engine before performing any work on  
the hydraulic system.  
1.6 SAFETY SIGNS  
1.6.1  
Keep all safety signs legible. Remove all grease, dirt, and debris from safety  
signs and instructional labels.  
1.6.2  
1.6.3  
Safety signs must be replaced if they are missing or illegible.  
When new components are installed, be sure that current safety signs are  
affixed to the replaced components.  
1.6.4  
1.6.5  
1.6.6  
New safety signs may be obtained from your authorized Exmark equipment  
dealer or distributor or from Exmark Mfg. Co. Inc.  
Safety signs may be affixed by peeling off the backing to expose the adhesive  
surface. Apply only to a clean, dry surface. Smooth to remove any air bubbles.  
Familiarize yourself with the following safety signs and instruction labels. They  
are critical to the safe operation of your Exmark commercial mower.  
PART NO. 103-4891  
LOCATION: Center of Console  
PART NO. 98-5954  
LOCATION: Under Mower Deck  
Belt Shield(s)  
PART NO. 1-513742  
LOCATION: On Top of Mower  
Deck Belt Shields, Left  
and Right Sides  
PART NO. 1-513748  
LOCATIONS: Bottom of  
Floorpan  
- 8 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PART NO. 1-523552  
LOCATION: Top of Hydraulic  
Reservoir  
Type A Anti-Scalp Rollers Only –  
See Figure 10  
PART NO. 1-403005  
LOCATION: Left and Right Corners  
of Mower Deck  
PART NO. 1-323540  
LOCATION: Left Front Corner  
PART NO. 103-2644  
LOCATION: Top of Hydraulic  
Reservoir  
PART NO. 107-2112  
LOCATION: Top Center of Floorpan  
PART NO. 1-303508  
LOCATION: Front Right Corner  
PART NO. 1-513746  
LOCATION: Rear of Engine  
Deck, Left and  
Top of Mower Deck  
Right Sides  
PART NO. 108-5995  
LOCATION: Top of Console Under Seat  
PART NO. 103-0262  
LOCATION: Below Center of  
Console  
PART NO. 1-653477  
LOCATION: Left of Center on Mower  
Deck, Under Floor Pan  
PART NO. 1-633922  
LOCATION: Front Left Corner Top  
of Mower Deck  
- 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PART NO. 103-4903  
LOCATION: Top Front of RH  
Fuel Tank  
PART NO. 103-6340  
LOCATION: Bottom Side of Floor Pan  
PART NO. 107-2102  
LOCATION: Inside Surface of  
Upper Roll bar  
PART NO. 1-653147  
LOCATION: Lefthand Side of Cutting  
Height Adjustment Plate  
PART NO. 103-4930  
LOCATION: Right of Choke  
Control on RH  
PART NO. 103-4892  
Fuel Tank  
LOCATION: Right of Throttle  
Control on RH  
PART NO. 103-7491  
LOCATION: On Top LH Side of Mower Deck  
Fuel Tank  
2. SPECIFICATIONS  
2.1 MODEL NUMBER:  
Serial Nos. 510,000 & Higher: LHP4419KA; LHP4819KA; LHP4820KC; LHP4823KA  
LHP5220KC; LHP5223KC; LHP5223KA;  
2.2 ENGINE:  
2.2.1  
2.2.2  
Engine Specifications: See Your Engine Owner’s Manual  
RPM: Full Speed: 3600 RPM (No Load) Idle: 1500 RPM  
- 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.3 FUEL SYSTEM  
2.3.1  
2.3.2  
2.3.3  
Capacity: 11.2 gal. (42 L.)  
Type of Fuel: Regular unleaded gasoline, 87 octane or higher.  
Fuel Filter: For Kohler: Replaceable in-line 15 Micron Kohler P/N 2405002  
For Kawasaki: Replaceable in-line Kawasaki P/N 49019-2075  
Fuel Shut-Off Valve: 1/4 turn increments (left tank, “OFF”, right tank)  
Fuel gauge in left hand fuel tank.  
2.3.4  
2.3.5  
2.4 ELECTRICAL SYSTEM  
2.4.1  
2.4.2  
2.4.3  
2.4.4  
2.4.5  
2.4.6  
2.4.7  
Charging System: Flywheel Alternator  
Charging Capacity: 15 amps  
Battery Type: BCI Group U1  
Battery Voltage: 12 Volt  
Polarity: Negative Ground  
Fuses: Two 20 amp blade type  
Safety Interlock System:  
PTO must be disengaged, brake engaged, and motion control levers out  
(neutral lock) to start engine. (It is not necessary for the operator to be in the seat  
to start the engine.)  
Operator must be in seat when PTO is engaged, brake is disengaged, or motion  
control levers are moved in or engine will stop.  
Engine will stop if either the left, the right, or both levers are moved from neutral  
lock position while brake is engaged.  
2.5 OPERATOR CONTROLS  
2.5.1  
Steering and Motion Control:  
Separate levers, on each side of the console, control speed and direction of travel  
of the respective drive wheels.  
Steering is controlled by varying the position of the levers relative to each other.  
Moving motion control levers outward (in slots) locks the drive system in neutral.  
Motion control levers are adjustable to two heights.  
2.5.2  
2.5.3  
2.5.4  
2.5.5  
PTO Switch: Engages electric clutch (to drive belt) which engages mower blades.  
Parking Brake Lever: Engages parking brakes.  
Deck Height Adjustment Lever: Sets cutting height to desired position.  
Deck Lift Assist Lever (standard on 48” & 52” units, optional accessory for 44”  
units): Foot pedal that assists in raising the deck.  
2.6 SEAT  
2.6.1  
Type:  
Standard seat: high back, foam padded (internal spring  
suspension) with arm rests.  
Optional seat accessories:  
Custom ride suspension system to enhance Standard Seat.  
Deluxe suspension seat with high back, low profile foam-in-place cushion  
(dampened, adjustable spring suspension) and armrests.  
2.6.2  
Mounting: Hinged to tilt up for access to hydraulic pumps, battery and other  
components. Held in tilted position with prop rod. Adjustable fore and aft seat track.  
- 11 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.6.3  
2.6.4  
Armrests: Standard seat: foam padded flip-up armrests with height adjustment.  
Optional suspension seat: molded adjustable flip-up armrests.  
Seat Safety Switch: Incorporated into the Safety Interlock System.  
Time delay seat switch eliminates rough ground cut-outs.  
2.7 HYDROSTATIC GROUND DRIVE SYSTEM  
2.7.1  
2.7.2  
2.7.3  
2.7.4  
Hydrostatic Pumps: Two Hydro Gear BDP-10A variable displacement piston pumps.  
Wheel Motors: Two Parker/Ross with 1 1/4” tapered shafts.  
Hydraulic Oil: Use Mobil 1 15W-50 Synthetic Motor Oil.  
Hydraulic Oil Capacity: 2.1 qt. (2.0 L.)  
2.7.5  
Hydraulic Filter: Replaceable cartridge type.  
P/N 1-513211: 10 microns, 18 psi bypass (Summer use above 32° F (0°C))  
P/N 1-523541: 40 microns, 18 psi bypass (Winter use below 32° F(0°C))  
2.7.6  
Speeds: 44” & 48” units: 0 - 8.1 mph (13.1 km/hr) forward.  
0 – 4.7 mph (7.6 km/hr) reverse.  
52” units: 0 – 9.5 mph (15.3 km/hr) forward.  
0 – 5.5 mph (8.9 km/hr) reverse.  
2.7.7  
Drive wheel release valves allow machine to be moved when the engine is not  
running.  
2.8 TIRES AND WHEELS  
2.8.1  
Tires:  
Size  
Qty  
Tread  
Ply  
Inflation  
Drive Tires  
23 x 9.5-12  
2
“Multi Trac C/S”  
4
13 psi (90 kPa)  
Front Caster Tires  
(Semi-Pneumatic)  
13 x 5.00-6  
2
Smooth  
2.9 CUTTING DECK  
2.9.1  
Cutting Width:  
44” deck  
48” deck  
52” deck  
44 in. (111.8 cm) 47.2 in. (120.0 cm) 52 in. (132.1 cm)  
Discharge: Side (Optional Mulch or Bag)  
2.9.2  
2.9.3  
Blade Size:  
(3 ea.)  
44” deck  
48” deck  
52” deck  
15.25 in. (38.7 cm) 16.25 in. (41.3 cm) 18.00 in. (45.7 cm)  
2.9.4  
2.9.5  
Blade Spindles: solid steel spindles with 1” (2.54 cm) I.D. bearings.  
Deck Drive: Electric clutch mounted on vertical engine shaft. Blades are driven  
by one “B” Section belt (w/self-tensioning idler) direct from the engine.  
2.9.6  
Deck: Full floating deck is attached to out-front support frame.  
Maximum turf protection is provided by three anti-scalp rollers on 44” &  
48” decks and five anti-scalp rollers on 52” decks.  
Deck design allows for bagging, mulching or side discharge.  
2.9.7  
Cutting Height Adjustment: an extra-long cushioned lever is used to adjust the  
cutting height from 1 1/2” (3.8 cm) to 4.5” (11.4 cm.) in 1/4” (.64 cm.) increments.  
The cutting height adjustment handle has a transport position and all  
adjustments can be made while the operator remains seated. 48” & 52” units  
also have a foot operated deck lift assist lever to aid in raising the deck. (The  
deck lift assist lever is an optional accessory for the 44” deck.)  
2.9.8  
Mulching Kit: Optional.  
- 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.10 DIMENSIONS  
2.10.1 Overall Width:  
Without deck  
Discharge chute up Discharge chute down  
w/44” Deck 43.9 in. (111.5 cm)  
w/48” Deck 45.9 in. (116.6 cm)  
47.4 in. (120.3 cm)  
50.3 in. (122.4 cm)  
54.7 in. (138.9 cm)  
58.1 in. (147.6 cm)  
w/52” Deck 47.9 in. (121.7 cm)  
54.7 in. (138.9 cm)  
63.2 in. (160.5 cm)  
2.10.2 Overall Length:  
w/44” Deck  
w/48” Deck  
w/52” Deck  
Roll Bar - Up  
74.1 in. (188.2 cm) 74.1 in. (188.2 cm) 77.3 in. (196.3 cm)  
Roll Bar - Down 80.2 in. (203.7 cm) 80.2 in. (203.7 cm) 83.4 in (211.8 cm)  
2.10.3 Overall Height:  
Roll Bar - Up  
Roll Bar - Down  
69.4 in. (176.3 cm) 51.3 in. (130.3 cm)  
2.10.4 Tread Width: (center to center of tires, widthwise)  
w/44” Deck  
w/48” Deck  
w/52” Deck  
34.4 in. (87.4 cm)  
32.2 in. (81.8 cm)  
36.4 in. (92.5 cm)  
32.2 in. (81.8 cm)  
38.4 in. (97.5 cm)  
34.6 in. (87.9 cm)  
Drive Wheels  
Front Casters  
2.10.5 Wheel Base: (center of caster tire to center of drive tire)  
w/44” & 48” Decks  
w/52” Deck  
45.9 in. (116.6 cm) 47.2 in. (119.9 cm)  
2.10.6 Curb Weight:  
w/44” Deck  
w/48” Deck  
w/52” Deck  
963 lbs. (437 kg)  
983 lbs. (446 kg)  
1103 lbs. (500 kg)  
* Note: Weight will vary slightly, depending on engine option.  
2.11 TORQUE REQUIREMENTS  
Bolt Location  
Torque  
Cutter Housing Spindle Nut (secured with threadlocker) 140-145 ft-lbs. (190-197 N-m)  
Blade Mounting Bolt............................................................55-60 ft-lbs. (75-81 N-m)  
Engine Deck/Front Frame Mount Bolts ...............................30-35 ft-lbs. (41-47 N-m)  
Anti-Scalp Roller (See Figure 10)  
Type A – Whizlock Nut ...............................................40-45 ft-lbs. (54-61 N-m)  
Type B – Nyloc Nut.....................................................30-35 ft-lbs. (41-47 N-m)  
Type B – Hex Capscrew.............................................50-55 ft-lbs. (68-75 N-m)  
Engine Mounting Bolts .......................................................15-20 ft-lbs. (20-27 N-m)  
Wheel Motor Mounting Bolts.............................................72-77 ft-lbs. (98-104 N-m)  
Wheel Hub Slotted Nut ...............................................minimum125 ft-lbs. (169 N-m)  
Wheel Lug Nuts ..............................................................90-95 ft-lbs. (122-129 N-m)  
Rollover Protection System (Roll Bar) Mounting Bolts.........30-35 ft-lbs. (41-47 N-m)  
Clutch Retaining Bolt (secured with threadlocker)...............55-60 ft-lbs. (75-81 N-m)  
3. ASSEMBLY INSTRUCTIONS  
3.1 UNCRATE MOWER  
3.2 INSTALL ROLLOVER PROTECTION SYSTEM (ROLL BAR)  
3.2.1  
Disassemble roll bar from the crate.  
a) Remove roll bar tubes from sides of crate and remove screws that attach the  
wheel hub retaining plate to the bottom of the crate.  
b) Remove the two brackets used to mount the bottom of the upper roll bar tube  
to the crate. Remove the 1/2-13 x 3 1/4 capscrews and 1/2-13 hex flange  
lock nuts from the two brackets at each end of the upper roll bar tube and  
retain for later use.  
- 13 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.2.2  
Raise the rear of the unit and support it with jack stands or equivalent support.  
CAUTION  
POTENTIAL HAZARD  
Raising the rear of the unit for assembly relying solely  
on mechanical or hydraulic jacks could be dangerous.  
WHAT CAN HAPPEN  
The mechanical or hydraulic jacks may not be enough  
support or may malfunction allowing the unit to fall,  
which could cause injury.  
HOW TO AVOID THE HAZARD  
DO NOT rely solely on mechanical or hydraulic jacks  
for support. Use adequate jack stands or equivalent  
support.  
3.2.3  
3.2.4  
Remove the wheel nuts from both sides of the unit and retain for later use.  
Install the two lower roll bar tubes.  
a) Locate the left and right lower roll bar tubes.  
b) Align lower roll bar tubes along wheel motor channels as shown in Figure 2.  
c) LOOSELY install lower roll bar hardware (four 3/8-16 x 1 capscrews, four  
spring disk washers and four 3/8-16 whizlock nuts) from the bolt bag to the  
tubes on each side as shown in Figure 2.  
NOTE: Be sure the spring disk washer cone is installed towards the head of  
the capscrew.  
FIGURE 2  
LOWER ROLL BAR INSTALLATION  
3.2.5  
Install the upper u-shaped section of the roll bar. (Reference Figure 3 for  
alignment and installation instructions below):  
a) Locate the latch pin assemblies (pin and hairpin connected with a lanyard).  
b) Install a 1/2-13 x 3 1/4 capscrew in the washer on the lanyard of each pin  
assembly.  
Note: Make sure the bent tab in the washer is towards the head of the bolt.  
b) Lightly oil the inside surfaces of the ear-shaped plates at the upper end of  
the lower roll bar tubes.  
- 14 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
c) Locate the upper u-shaped section of the roll bar. Install the upper roll bar  
section using the two 1/2-13 x 3 1/4 capscrews from step b and two 1/2-13  
hex flange lock nuts. Do not over tighten. Make sure upper roll bar can  
pivot freely.  
Notes:  
Make sure the capscrew and nuts are installed with the nut to the inside of  
the roll bar.  
Make sure the tab on the lanyard washer is installed as shown and points  
toward the front of the unit.  
d) Torque all lower roll bar hardware attached to the machine frame to 30 ft-lbs.  
(41-47 N-m).  
e) Tighten the front knobs against the upper roll bar ends.  
FIGURE 3  
UPPER ROLL BAR INSTALLATION  
3.3 SERVICE BATTERY  
WARNING: Battery posts, terminals, and related accessories contain lead compounds, chemicals known  
to the State of California to cause cancer and reproductive harm. Wash hands after handling.  
The machine is shipped with a filled lead acid battery.  
3.3.1  
Unhook seat latch and tilt seat up to gain access to the battery.  
DANGER  
POTENTIAL HAZARD  
Charging the battery may produce explosive gasses  
WHAT CAN HAPPEN  
Battery gasses can explode causing serious injury.  
HOW TO AVOID THE HAZARD  
Keep sparks, flames, or cigarettes away from battery.  
Ventilate when charging or using battery in an  
enclosed space.  
Make sure venting path of battery is always open once  
battery is filled with acid.  
- 15 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.3.2  
Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of  
the battery in the table below and charge the battery for the recommended time  
interval to bring the charge up to a full charge of 12.6 volts or greater.  
IMPORTANT: Make sure the negative battery cables are disconnected and the  
battery charger used for charging the battery has an output of 16 volts and 7  
amps or less to avoid damaging the battery (see chart below for recommended  
charger settings).  
Voltage  
Reading  
Percent  
Charge  
Maximum  
Charger Settings  
Charging Interval  
12.6 or greater 100%  
16 volts/7 amps  
No Charging Required  
30 Minutes  
1 Hour  
2 Hours  
3 Hours  
12.4 – 12.6  
12.2 – 12.4  
12.0 – 12.2  
11.7 – 12.0  
11.7 or less  
75 – 100% 16 volts/7 amps  
50 – 75%  
25 – 50%  
0 – 25%  
0%  
16 volts/7 amps  
14.4 volts/4 amps  
14.4 volts/4 amps  
14.4 volts/2 amps  
6 Hours or More  
CAUTION  
POTENTIAL HAZARD  
If the ignition is in the “ON” position there is potential  
for sparks and engagement of components.  
WHAT CAN HAPPEN  
Sparks could cause an explosion or moving parts  
could accidentally engage causing personal injury.  
HOW TO AVOID THE HAZARD  
Be sure ignition switch is in the “OFF” position before  
charging the battery.  
3.3.3  
Connect the negative battery cables.  
NOTE: If the positive cable is also disconnected, connect the positive (red)  
cable to the positive battery terminal first, then the negative (black) cable and  
green/white wire to the negative battery terminal. Slip insulator boot over the  
positive terminal.  
NOTE: If time does not permit charging the battery, or if charging equipment is  
not available, connect the negative battery cables and run the vehicle  
continuously for 20 to 30 minutes to sufficiently charge the battery.  
3.4 INSTALL DRIVE WHEELS  
3.4.1 Mount drive wheels with the valve stem to the outside of the unit. Secure using  
four (4) 1/2-20 wheel nuts (installed on studs in hubs) for each wheel. Torque to  
95 ft-lbs (128 NxM).  
3.5 CHECK TIRE PRESSURE  
3.5.1 Check tire pressure in drive tires. Proper inflation pressure for tires is 13 psi (90  
kPa). Adjust if necessary.  
Semi-Pneumatic caster tires do not need to be inflated.  
3.6 INSTALL SEAT  
3.6.1 a) Remove seat assembly from the crate.  
- 16 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b) Remove the four 5/16-18 whizlock nuts from the seat track studs at the  
bottom of the seat. Retain for use later.  
c) Align the seat track studs on the bottom of the seat with the holes in the  
seat frame. Place seat on top of the frame and secure with the four 5/16-18  
whizlock nuts remove in step b).  
3.7 INSTALL MOTION CONTROL LEVERS  
3.7.1  
Loosen and remove the two (2) 3/8” x 1” bolts and spring disc washers which  
attach the motion control levers to the control arm shafts for shipping and the  
two (2) 3/8” x 1” bolts and spring disc washers which are screwed into the control  
arm shafts.  
a) Install the left motion control lever onto the control arm shaft (See Figure 4)  
on the left side of the console. Place the lever (with the mounting plate  
towards the rear) on the outside of the control arm shaft and secure with  
the bolts and washers. Position the lever so the bolts are in the center of  
the slots on the lever mounting plate and tighten until snug. Repeat on  
opposite side of unit.  
NOTE: There are two lever height options available. Place the levers in the  
top two holes to increase height of the levers, or in the bottom two holes to  
decrease the height of the levers.  
If the levers do not align with each other, when in the neutral position, (See  
Figure 5) loosen the hardware and make the appropriate adjustment by  
sliding/tilting the lever(s) forward or backward until properly aligned and  
tighten hardware.  
LEVERS IN  
ALIGNMENT  
MOTION  
CONTROL  
LEVER  
MOUNT PLATE TO  
THE REAR & OUTSIDE  
OF ARM SHAFT  
FIGURE 4  
CONTROL ARM SHAFT  
FIGURE 5  
LEVER ALIGNMENT  
b) If the ends of the levers hit against each other, while in the drive  
position (levers rotated in as far as possible), make adjustments by moving  
the levers outwards to the neutral lock position and carefully bending them  
outward. Move them back to the drive position and check for clearance,  
repeat if necessary.  
3.8 POSITION DISCHARGE CHUTE  
3.8.1 Loosen two (2) 5/16” nyloc nuts attaching discharge chute. Lower the discharge  
chute into position. Retighten nyloc nuts until chute is snug but can pivot freely.  
3.9 SERVICE ENGINE  
Engine is shipped with oil, check oil level and if necessary fill to the appropriate  
level with SAE 10W-30 or 10W-40, AP1 service class SF or SG for operating in  
temperatures above 0° F (-18° C). See Engine Operator's Manual.  
- 17 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.10 SERVICE HYDRAULIC OIL  
The machine is shipped with hydraulic oil in the reservoir. Run the machine for  
approximately 15 minutes to allow any extra air to purge out of the hydraulic  
system. Check hydraulic reservoir and if necessary fill the reservoir to the  
appropriate level with Mobil 1 15W-50 synthetic motor oil. Replace hydraulic  
reservoir cap and tighten until snug. Do not overtighten.  
NOTE: The baffle is labeled “HOT” and “COLD”. The oil level varies with the  
temperature of the oil. The “HOT” level shows the level of oil when it is at 225°F  
(107°C). The “COLD” level shows the level of the oil when it is at 75°F (24°C).  
Fill to the appropriate level depending upon the temperature of the oil. For  
example: If the oil is about 150° F (65°C). Fill to halfway between the “HOT” and  
“COLD” levels. If the oil is at room temperature (about 75° F (24°C)), fill only to  
the “COLD” level.  
4. OPERATION INSTRUCTIONS  
4.1 CONTROLS  
4.1.1  
4.1.2  
Familiarize yourself with all controls before operating the mower.  
Motion Control Levers: Located on each side of the console.  
The left lever controls the flow of hydraulic oil from the left hydrostatic pump to  
the left drive wheel motor. The right lever controls the flow of hydraulic oil from  
the right hydrostatic pump to the right drive wheel motor.  
IMPORTANT: To begin movement (forward or backward) the operator must  
be in the seat, the brake lever must be disengaged (pushed down) before  
the motion control levers can be moved in or the engine will kill.  
When levers are centered in the T-slot the drive system is in the neutral position.  
With levers moved out in the T-slot the drive system is in the neutral lock  
position (See Figure 6).  
FIGURE 6  
MOTION CONTROL POSITIONS  
By moving both levers an equal amount forward or back from the neutral position  
the machine can be caused to move forward or backward in a straight line.  
Movement of the left lever forward will cause the left drive wheel to rotate in a  
forward direction. Movement of the right lever forward will cause the right  
drive wheel to rotate in a forward direction. To stop forward travel, pull the  
levers back to the neutral position.  
To turn left while moving forward, move the left lever back toward neutral to  
slow the left drive wheel. To turn right while moving forward, move the right  
lever back toward neutral to slow the right drive wheel.  
To make a zero turn to the left, pull the left lever back beyond neutral while  
holding the right lever slightly ahead of neutral.  
To make a zero turn to the right, pull the right lever back beyond neutral while  
holding the left lever slightly ahead of neutral.  
- 18 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pulling the levers back from the neutral position will cause the respective drive  
wheels to rotate in a reverse direction (spring tension can be felt when moving  
into reverse from neutral).  
To turn to the left while backing, move the left lever forward toward neutral. To  
turn to the right while backing, move the right lever forward toward neutral.  
CAUTION  
POTENTIAL HAZARD  
Machine can spin very rapidly by positioning one lever  
too much ahead of the other.  
WHAT CAN HAPPEN  
Operator may lose control of the machine, which may  
cause damage to the machine or injury.  
HOW TO AVOID THE HAZARD  
Use caution when making turns.  
Slow the machine down before making sharp turns.  
4.1.3  
Tracking Adjustment Knob: Located under the seat on the LH pump control link.  
Rotating this knob allows fine tuning adjustments so that the machine tracks straight  
with the drive levers in the full forward position.  
Stop machine and wait for all moving parts to stop. Engage park brake. Unhook  
seat latch and tilt seat forward to gain access to the tracking knob. Rotate the knob  
counter-clockwise (as viewed from the rear of the machine) to cause the machine to  
track more to the right and clockwise to cause the machine to track more to the left.  
Adjust in quarter-turn increments until the machine tracks straight. Check that the  
machine does not creep when in neutral with the park brakes disengaged.  
IMPORTANT: Do not rotate the knob too far, as this may cause the machine  
to creep in neutral. Refer to section 5.2.11 for control linkage adjustment.  
4.1.4  
4.1.5  
PTO Engagement Switch: Located on the right fuel tank.  
Switch must be pulled out to the “ROTATE” position to engage the blades.  
Switch is pushed in to the “STOP” position to stop the blades.  
Choke Control: Located on the right fuel tank.  
Choke is used to aid in starting a cold engine. Moving the choke lever forward  
will put the choke in the “ON” position and moving the choke lever to the rear  
will put the choke in the “OFF” position. DO NOT run a warm engine with choke  
in the “ON” position.  
4.1.6  
4.1.7  
Throttle Control: Located on the right fuel tank.  
Throttle is used to control engine speed. Moving throttle lever forward will increase  
engine speed and moving throttle lever to the rear will decrease engine speed.  
Brake Lever: Located on left side of the console. The brake lever engages a  
parking brake on the drive wheels.  
Pull the lever up and rearward to engage the brake.  
Push the lever forward and down to disengage the brake.  
The unit must be tied down and brake engaged when transporting.  
Ignition Switch: Located on the right fuel tank.  
4.1.8  
The ignition switch is used to start and stop the engine. The switch has three  
positions “OFF”, “ON” and “START”. Insert the key into switch and rotate  
clockwise to the “ON” position.  
Rotate clockwise to the next position to engage the starter (key must be held  
against spring pressure in this position).  
- 19 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Brake must be engaged, motion control levers out (neutral lock position)  
and PTO switch “OFF” to start engine. (It is not necessary for the operator to  
be in the seat to start the engine.)  
4.1.9  
Hour Meter: Located on the right fuel tank.  
The hour meter is connected to a pressure switch installed in the engine block  
and it records the number of hours that the engine has run. If ignition switch is  
left on without engine running, hour meter will not run.  
NOTE: This switch is not a low oil sensor and will not alert the operator if the  
engine oil is low.  
4.1.10 Fuel Shut-Off Valve: Located directly below center of console.  
The fuel shut-off valve is used to shut off the fuel when the machine will not be  
used for a few days, during transport to and from the jobsite, and when parked  
inside a building. The valve has three positions, each position made in 1/4  
turn increments.  
Valve handle down is the “OFF” position. Rotate valve handle 1/4 turn right  
(from “Off” position) for fuel flow from the right tank. Rotate valve handle 1/4  
turn left (from “Off” position) for fuel flow from the left tank.  
4.1.11 Fuel Gauge: Located on the left fuel tank.  
The fuel gauge monitors the amount of fuel in the left tank only. Use the fuel  
from the right fuel tank first. When the right fuel tank is empty switch to the left  
fuel tank. Fuel gauge will monitor the remaining fuel.  
4.1.12 Drive Wheel Release Valves: Located on the right front corner of the hydrostatic  
pumps. Drive wheel release valves are used to release the hydrostatic drive  
system to allow the machine to be pushed without the engine running. Unhook  
seat latch and tilt seat up to gain access to pumps.  
With a 5/8 wrench, turn both valves one turn counter-clockwise to release drive  
system.  
Turn clockwise to reset system. DO NOT overtighten. DO NOT tow machine.  
4.2 PRE-START  
4.2.1  
Fill fuel tanks. For best results use only clean, fresh regular grade unleaded  
gasoline with an octane rating of 87 or higher. Regular grade leaded gasoline may  
also be used; however, combustion chamber and cylinder head will require more  
frequent service. See Engine Owner's Manual. DO NOT add oil to gasoline.  
Do Not overfill fuel tank. Never fill the fuel tank so that the fuel level rises above a  
level that is 1/2” below the bottom of the filler neck to allow for fuel expansion and  
prevent fuel spillage.  
4.2.2  
4.2.3  
Make sure you understand the controls, their locations, their functions, and their  
safety requirements.  
Refer to Maintenance, Section 5, and perform all the necessary inspection and  
maintenance steps.  
4.3 MOWING  
4.3.1  
Operate units with the roll bar in the raised and locked position and use seat belt.  
There is no rollover protection when the roll bar is down. If it is necessary to  
lower roll bar do not wear the seat belt. Raise the roll bar as soon as clearance  
permits.  
4.3.2  
Open fuel shut-off valve (left or right tank).  
- 20 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.3.3  
Starting Engine:  
Brake must be engaged, the PTO switch disengaged, and the motion  
control levers out (neutral lock position). (The operator does not need to be  
in the seat to start the engine.)  
On a cold engine, place the throttle midway between the “SLOW” and “FAST”  
positions and push choke lever forward to the “ON” position. Turn ignition  
switch to the “start” position. Release the switch as soon as the engine starts.  
IMPORTANT: DO NOT crank the engine continuously for more than ten (10)  
seconds at a time. If the engine does not start, allow a 60 second cool-  
down period between starting attempts. Failure to follow these guidelines  
can burn out the starter motor.  
After starting a cold engine, gradually return choke to the “OFF” position as the  
engine warms up.  
On a warm engine, place the throttle midway between the “SLOW” and “FAST”  
positions and leave the choke in the “OFF” position.  
4.3.4  
Engaging PTO  
DANGER  
POTENTIAL HAZARD  
The rotating blades under the mower deck are  
dangerous.  
WHAT CAN HAPPEN  
Blade contact can cause serious injury or kill you.  
HOW TO AVOID THE HAZARD  
DO NOT put hands or feet under the mower or mower  
deck when the blades are engaged.  
DANGER  
POTENTIAL HAZARD  
An uncovered discharge opening will allow objects to  
be thrown in an operator’s or bystander’s direction.  
Also, contact with the blade could occur.  
WHAT CAN HAPPEN  
Thrown objects or blade contact can cause serious  
injury or death.  
HOW TO AVOID THE HAZARD  
Never operate the mower with the discharge deflector  
raised, removed, or altered unless there is a grass  
collection system or mulch kit in place and working  
properly.  
The PTO clutch push-pull switch engages the cutting blades. Be sure that all  
persons are clear of mower deck and discharge area before engaging PTO.  
IMPORTANT: Operator must be in seat before the PTO can be engaged.  
Set throttle to "midway" position. Pull outward on the switch to the “ROTATE”  
position. Accelerate to full throttle to begin mowing.  
4.3.5  
4.3.6  
Stopping PTO: Set the throttle to the “midway” position. Push in on the switch to  
the “STOP” position stopping the PTO.  
Stopping Engine: Bring unit to a full stop. Disengage the PTO, move motion  
control levers out to the neutral lock position and engage parking brake.  
- 21 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before stopping the engine, place the throttle control midway between the “slow”  
and “fast” positions. Allow the engine to run a minimum of 15 seconds; then  
stop the engine.  
Rotate ignition switch to “OFF” position. Remove the key to prevent children or  
other unauthorized persons from starting engine.  
Close fuel shut-off valve when machine will not be used for a few days, when  
transporting, and when the unit is parked inside a building.  
4.4 TRANSPORTING  
4.4.1  
Transporting a Unit: Use a heavy-duty trailer or truck to transport the machine.  
Lock brake and block wheels. Securely fasten the machine to the trailer or truck  
with straps, chains, cable, or ropes. Be sure that the trailer or truck has all  
necessary lighting and marking as required by law.  
Secure a trailer with a safety chain.  
CAUTION  
POTENTIAL HAZARD  
This unit does not have proper turn signals, lights,  
reflective markings, or a slow moving vehicle emblem.  
These items are required to drive on a public street or  
roadway.  
WHAT CAN HAPPEN  
Driving on a street or roadway without such equipment  
is dangerous and can lead to accidents causing  
personal injury.  
Driving on a street or roadway without such equipment  
may also be a violation of State laws and the operator  
may be subject to traffic tickets and/or fines.  
HOW TO AVOID THE HAZARD  
Do not drive a unit on a public street or roadway.  
WARNING  
POTENTIAL HAZARD  
Loading a unit on a trailer or truck increases the  
possibility of backward tip-over.  
WHAT CAN HAPPEN  
Backward tip-over of the unit could cause serious  
injury or death.  
HOW TO AVOID THE HAZARD  
Use extreme caution when operating a unit on a ramp.  
Use only a single, full width ramp; DO NOT use  
individual ramps for each side of the unit.  
If individual ramps must be used, use enough ramps to  
create an unbroken ramp surface wider than the unit.  
DO NOT exceed a 15° angle between ramp and  
ground or between ramp and trailer or truck.  
Avoid sudden acceleration while driving unit up a ramp  
to avoid tipping backward.  
Avoid sudden deceleration while backing unit down a  
ramp to avoid tipping backward.  
- 22 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.4.2  
Loading a Unit: Use extreme caution when loading units on trailers or trucks.  
One full width ramp that is wide enough to extend beyond the rear tires is  
recommended instead of individual ramps for each side of the unit. The lower  
rear section of the tractor frame extends back between the rear wheels and  
serves as a stop for tipping backward. Having a full width ramp provides a  
surface for the frame members to contact if the unit starts to tip backward. If it is  
not possible to use one full width ramp, use enough individual ramps to simulate  
a full width continuous ramp.  
Ramp should be long enough so that the angles between the ramp and the  
ground and the ramp and the trailer or truck do not exceed 15°. A steeper angle  
may cause mower deck components to get caught as the unit moves from ramp  
to trailer or truck. Steeper angles may also cause the unit to tip backward. If  
loading on or near a slope, position the trailer or truck so it is on the down side of  
the slope and the ramp extends up the slope. This will minimize the ramp angle.  
The trailer or truck should be as level as possible.  
DO NOT attempt to turn the unit while on the ramp, you may lose control and  
drive off the side.  
Avoid sudden acceleration when driving up a ramp and sudden deceleration when  
backing down a ramp. Both maneuvers can cause the unit to tip backward.  
5. MAINTENANCE & ADJUSTMENTS  
WARNING  
POTENTIAL HAZARD  
While maintenance or adjustments are being made,  
someone could start the engine.  
WHAT CAN HAPPEN  
Accidental starting of the engine could seriously injure  
you or other bystanders.  
HOW TO AVOID THE HAZARD  
Remove the key from the ignition switch and pull the  
wire(s) off the spark plug(s) before you do any  
maintenance. Also push the wire(s) aside so it does  
not accidentally contact the spark plug(s).  
WARNING  
POTENTIAL HAZARD  
The engine can become very hot.  
WHAT CAN HAPPEN  
Touching a hot engine can cause severe burns.  
HOW TO AVOID THE HAZARD  
Allow the engine to cool completely before service or  
making repairs around the engine area.  
5.1 PERIODIC MAINTENANCE  
5.1.1 Check engine oil level:  
Service Interval: Daily  
a) Stop engine, wait for all moving parts to stop and make sure unit is on a  
level surface.  
b) Check with engine cold.  
c) Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the  
dipstick. Do not screw into place. Remove the dipstick and read the oil level.  
- 23 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
d) If the oil level is low, add oil to bring the oil level up to the “FULL” mark on  
the dipstick. Use oil as specified in the Engine Owner’s Manual.  
DO NOT overfill.  
IMPORTANT: DO NOT operate the engine with the oil level below the  
“LOW” (or “ADD”) mark on the dipstick, or over the “FULL” mark.  
5.1.2  
Clean engine air cooling system:  
Service Interval: Daily or more often in dry conditions  
CAUTION  
POTENTIAL HAZARD  
Excessive debris can cause the engine and hydraulic  
system to overheat.  
WHAT CAN HAPPEN  
Excessive debris around the engine cooling air intake  
and inside of the pump compartment can create a fire  
hazard.  
HOW TO AVOID THE HAZARD  
Clean all debris from around the engine and hydraulic  
pumps daily.  
a) Stop engine, wait for all moving parts to stop, and remove key.  
b) Clean all debris from rotating engine air intake screen and from around  
engine shrouding.  
5.1.3  
Check battery charge:  
Service Interval: Monthly  
Allowing batteries to stand for an extended period without recharging them will  
result in reduced performance and service life. To preserve optimum battery  
performance and life, recharge batteries in storage when the open circuit voltage  
drops to 12.4 volts.  
Note: To prevent damage due to freezing, battery should be fully charged before  
putting away for winter storage.  
a)  
Check the voltage of the battery with a digital voltmeter. Locate the voltage  
reading of the battery in the table below and charge the battery for the  
recommended time interval to bring the charge up to a full charge of 12.6  
volts or greater.  
IMPORTANT: Make sure the negative battery cables are disconnected  
and the battery charger used for charging the battery has an output of 16  
volts and 7 amps or less to avoid damaging the battery (see chart below for  
recommended charger settings).  
Voltage  
Reading  
Percent  
Charge  
Maximum  
Charger Settings  
Charging Interval  
12.6 or greater 100%  
16 volts/7 amps  
No Charging Required  
30 Minutes  
1 Hour  
2 Hours  
3 Hours  
12.4 – 12.6  
12.2 – 12.4  
12.0 – 12.2  
11.7 – 12.0  
11.7 or less  
75 – 100% 16 volts/7 amps  
50 – 75%  
25 – 50%  
0 – 25%  
0%  
16 volts/7 amps  
14.4 volts/4 amps  
14.4 volts/4 amps  
14.4 volts/2 amps  
6 Hours or More  
5.1.4  
Clean grass build-up under deck.  
Service Interval: Daily  
a) Stop engine, wait for all moving parts to stop, and remove key.  
- 24 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b) Raise deck to the transport (4.5” (11.4cm) cutting height) position. Lift the  
front of unit and support unit using jack stands or equivalent support.  
CAUTION  
POTENTIAL HAZARD  
Raising the mower deck for service or maintenance  
relying solely on mechanical or hydraulic jacks could  
be dangerous.  
WHAT CAN HAPPEN  
The mechanical or hydraulic jacks may not be enough  
support or may malfunction allowing the unit to fall,  
which could cause injury.  
HOW TO AVOID THE HAZARD  
DO NOT rely solely on mechanical or hydraulic jacks  
for support. Use adequate jack stands or equivalent  
support.  
c) Clean out any grass build-up from underside of deck and in discharge chute.  
Check mower blades.  
5.1.5  
Service Interval: Daily  
a) Stop engine, wait for all moving parts to stop, and remove key.  
b) Lift deck and secure in raised position as stated in Section 5.1.4.  
c) Inspect blades and sharpen or replace as required.  
d)  
Re-install the blades (if they were removed) in the following order (See  
Figure 7):  
1) Install bushing through blade with bushing flange on bottom (grass)  
side of blade.  
2) Install bushing/blade combo into spindle.  
3) Install blade bolt and spring disc washer. Be sure the spring disc  
washer cone is installed towards the bolt head. Place a block of wood  
between front or rear baffles and the blade then torque the blade bolts  
to 55-60 ft-lbs. (75-81 N-m).  
FIGURE 7  
BLADE BOLT INSTALLATION  
IMPORTANT: DO NOT use components other than the original blade, blade  
bushing, spring disc washer, and blade bolt supplied with the unit. Failure to use  
all original components and assembled as shown will increase the risk of a blade  
bolt becoming loose or weak after striking a foreign object.  
- 25 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION  
POTENTIAL HAZARD  
Operating a mower deck with loose or weakened blade  
bolts can be dangerous.  
WHAT CAN HAPPEN  
A loose or weakened blade bolt could allow a blade  
rotating at a high speed to come out from under the deck,  
causing serious injury or property damage.  
HOW TO AVOID THE HAZARD  
Always re-install original Exmark blades, blade bushings,  
spring disc washers, and blade bolts in the correct  
positions as shown.  
5.1.6  
Check safety interlock system.  
Service Interval: Daily  
a) Check starting circuit. Starter should crank with parking brake engaged,  
PTO disengaged and motion control levers moved out in the neutral lock  
position. The operator does not need to be in the seat to start the engine.  
Try to start with operator in seat, parking brake disengaged, PTO  
disengaged and motion control levers in the neutral lock position - starter  
must not crank.  
Try to start with operator in seat, parking brake engaged, PTO engaged and  
motion control levers in the neutral lock position - starter must not crank.  
Try to start with operator in seat, parking brake engaged, PTO  
disengaged, and the left motion control lever in, starter must not  
crank, repeat again with the right lever in, then with both levers in -  
starter must not crank.  
b) Check kill circuits. Run engine at one-third throttle, disengage parking  
brake and raise off of seat (but do not get off of machine) engine must  
stop after approx. 1/2 second has elapsed (seat has time delay kill switch  
to prevent cut-outs on rough terrain).  
Run engine at one-third throttle, engage PTO and raise off of seat (but do  
not get off of machine) engine must stop after 1/2 second has elapsed.  
Run engine at one-third throttle, with brake disengaged, move levers in and  
raise off seat (but do not get off of machine) engine must stop after 1/2  
second has elapsed.  
Again, run engine at one-third throttle, brake engaged, and move left  
motion control lever in - engine must stop.  
Repeat again moving the right lever in, then moving both levers in -  
engine must stop whether operator is on seat or not.  
NOTE: If machine does not pass any of these tests, do not operate.  
Contact your authorized EXMARK SERVICE DEALER.  
IMPORTANT: It is essential that operator safety mechanisms be connected  
and in proper operating condition prior to use for mowing.  
5.1.7  
Check rollover protections systems (roll bar) pins  
Service Interval: Daily  
a)  
Make sure latch pin and hair pin are fully installed and lanyard is in good  
condition.  
- 26 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.1.8  
5.1.9  
Check for loose hardware.  
Service Interval: Daily  
Stop engine, wait for all moving parts to stop, and remove key.  
a)  
b)  
Visually inspect machine for any loose hardware or any other possible  
problem. Tighten hardware or correct the problem before operating.  
Service air cleaner.  
Service Interval: 50 hrs.  
More often under severe conditions.  
See Engine manual for additional information.  
a) Stop engine, wait for all moving parts to stop, and remove key.  
b) Loosen retaining clips and remove air cleaner compartment cover.  
c) Remove paper element. Check the condition of the paper element.  
Replace if dirty, bent or damaged.  
d) All units except 17HP Kawasaki: Check the condition of the inner element.  
Replace whenever it appears dirty, typically every other time the paper  
element is replaced. Clean the base around the inner element before  
removing, so dirt does not get into the engine.  
e)  
f)  
DO NOT wash or use pressurized air to clean paper element or inner element.  
Reinstall elements. Position the cover so that the rubber dust ejector is  
pointing downward and secure with retaining clips.  
5.1.10 Change engine oil:  
Service Interval: 100 hrs.  
NOTE: Change oil and filter after first five (5) hrs. of operation  
a)  
b)  
c)  
Stop engine, wait for all moving parts to stop, and remove key.  
Drain oil while engine is warm from operation.  
Oil drain valve is located on left hand side of Kohler engine and right hand  
side of Kawasaki engine. Place pan under machine to catch oil and open  
valve with 10 mm wrench. Allow oil to drain then close valve.  
d)  
Replace the oil filter every other oil change. Clean around oil filter and  
unscrew filter to remove. Before reinstalling new filter, apply a thin coating of  
oil on the surface of the rubber seal. Turn filter clockwise until rubber seal  
contacts the filter adapter then tighten filter an additional 2/3 to 3/4 turn.  
e)  
f)  
Clean around oil fill cap and remove cap. Fill to specified capacity and replace  
cap. Use oil recommended in engine owner’s manual. DO NOT overfill.  
Start the engine and check for leaks. Stop engine and recheck oil level.  
5.1.11 Check hydraulic oil level:  
Service Interval: 40 hr.  
a) Stop engine and wait for all moving parts to stop.  
b) Clean area around hydraulic reservoir cap and remove cap.  
c) Oil level should be to the top of the baffle inside the tank. If not add oil. Use  
only Mobil 1 15W-50 synthetic motor oil. Replace hydraulic reservoir cap  
and tighten until snug. Do not overtighten.  
NOTE: The baffle is labeled “HOT” and “COLD”. The oil level varies with the  
temperature of the oil. The “HOT” level shows the level of oil when it is at  
225°F (107°C). The “COLD” level shows the level of the oil when it is at 75°F  
(24°C). Fill to the appropriate level depending upon the temperature of the oil.  
For example: If the oil is about 150° F (65°C), fill to halfway between the “HOT”  
and “COLD” levels. If the oil is at room temperature (about 75° F (24°C)), fill  
only to the “COLD” level.  
- 27 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.1.12 Check tire pressures:  
Service Interval: 40 hrs.  
a) Stop engine, wait for all moving parts to stop, and remove key.  
b) Check tire pressure in drive tires.  
c) Inflate drive tires to 13 psi (90 kPa).  
d) Semi-pneumatic caster tires do not need to be inflated.  
NOTE: Do not add any type of tire liner or foam fill material to the tires.  
Excessive loads created by foam filled tires may cause failures to the hydro drive  
system, frame and other components. Foam filling tires will void the warranty.  
5.1.13 Check condition of belts:  
Service Interval: 40 hrs.  
a)  
b)  
c)  
Stop engine, wait for all moving parts to stop, and remove key.  
Check under engine deck to check pump drive belt.  
Remove left and right belt shields on deck and lift out floor pan to inspect  
deck drive belt.  
d)  
See Sections 5.2.3 and 5.2.4, for belt adjustment.  
5.1.14 Lubricate grease fittings:  
Service Interval: Refer to chart.  
a)  
b)  
Stop engine, wait for all moving parts to stop, and remove key.  
Lubricate fittings with one to two pumps of NGLI grade #2 multi-purpose  
gun grease.  
Refer to the following chart for fitting locations and lubrication schedule.  
LUBRICATION CHART  
FITTING  
LOCATIONS  
INITIAL  
PUMPS PLACES  
NO. of  
SERVICE  
INTERVAL  
1. Front Caster wheel hubs  
2. Front Caster Pivots  
2
2
5
1
2
1
2
0  
0  
1
yearly  
yearly  
40 hours  
Yearly  
3. Height Adjustment Shaft Bearings  
4. Deck Drive Belt Idler Arm  
5. Brake Brackets  
1
1
200 hours  
Yearly  
6. Pump Drive Belt Idler Arm  
7. Deck Rear Struts  
1
1
40 hours  
See 5.1.14 Section c) for special lubrication instructions on the front caster pivots and  
Section 5.1.15 for special lubrication instructions on the front caster wheel hubs.  
No. 6 (Pump Drive Belt Idler Arm)  
Located Under Engine Frame - Grease  
through hole in top of engine frame, between  
pumps.  
c)  
Lubricate front caster pivots once a year. Remove hex plug and cap. Thread  
grease zerk in hole and pump with grease until it oozes out around top  
bearing. Remove grease zerk and thread plug back in. Place cap back on.  
- 28 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.1.15 Lubricate caster wheel hubs:  
Service Interval: Once Yearly  
a)  
b)  
c)  
d)  
Stop engine, wait for all moving parts to stop, and remove key.  
Remove caster wheel from caster forks.  
Remove seal guards from the wheel hub.  
Remove one of the spacer nuts from  
the axle assembly in the caster wheel.  
Note that thread locking adhesive has  
been applied to lock the spacer nuts to  
the axle. Remove the axle (with the  
other spacer nut still assembled to it)  
from the wheel assembly.  
e)  
Pry out seals, and inspect bearings for  
wear or damage and replace if  
necessary.  
FIGURE 8  
CASTER WHEEL ASSEMBLY  
f)  
Pack the bearings with NGLI grade #1 multi-purpose grease.  
Insert (1) bearing, (1) new seal into the wheel.  
g)  
NOTE: Seals (Exmark PN 103-0063) must be replaced.  
h)  
If the axle assembly has had both spacer nuts removed (or broken loose),  
apply a thread locking adhesive to (1) spacer nut and thread onto the axle  
with the wrench flats facing outward. Do not thread spacer nut all of the way  
onto the end of the axle. Leave approximately 1/8” (3 mm) from the outer  
surface of the spacer nut to the end of the axle inside the nut.  
i)  
j)  
Insert the assembled nut and axle into the wheel on the side of the wheel  
with the new seal and bearing.  
With the open end of the wheel facing up, fill the area inside the wheel  
around the axle full of NGLI grade #1 multi-purpose grease.  
k)  
l)  
Insert the second bearing and new seal into the wheel.  
Apply a thread locking adhesive to the 2nd spacer nut and thread onto the axle  
with the wrench flats facing outward.  
m) Torque the nut to 75-80 in-lbs. (8-9 N-m), loosen, then re-torque to 20-25  
in-lbs. (2-3 N-m). Make sure axle does not extend beyond either nut.  
n)  
Re-install the seal guards over the wheel hub and insert wheel into caster  
fork. Re-install caster bolt and tighten nut fully.  
IMPORTANT: To prevent seal and bearing damage, check the bearing  
adjustment often. Spin the caster tire. The tire should not spin freely  
(more than 1 or 2 revolutions) or have any side play. If the wheel spins  
freely, adjust torque on spacer nut until there is a slight amount of drag.  
Re-apply threadlocking adhesive.  
5.1.16 Lubricate seat switch actuator:  
Service Interval: 160 hrs.  
a)  
b)  
c)  
Stop engine, wait for all moving parts to stop, and remove key.  
Unhook seat latch and tilt seat up.  
Lubricate switch actuator rod with spray type lubricant or light oil.  
5.1.17 Lubricate brake handle pivot:  
Service Interval: 160 hrs.  
a)  
Stop engine, wait for all moving parts to stop, and remove key.  
- 29 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b)  
Lubricate bronze bushings on brake handle pivot with a spray type lubricant  
or light oil.  
5.1.18 Lubricate brake rod bushings:  
Service Interval: 160 hrs.  
a)  
b)  
c)  
Stop engine, wait for all moving parts to stop, and remove key.  
Unhook seat latch and tilt seat up.  
Lubricate bronze bushings on each end of brake rod shafts with a spray  
type lubricant or a light oil. One shaft is located under the console. The  
other is below and behind the seat.  
5.1.19 Lubricate motion control bronze bushings:  
Service Interval: 160 hrs.  
a)  
b)  
c)  
Stop engine, wait for all moving parts to stop, and remove key.  
Unhook seat latch and tilt seat up.  
Lubricate bronze bushings on flange bearings securing the motion control  
arm shafts with a light oil or a spray type lubricant.  
5.1.20 Remove engine shrouds and clean cooling fins:  
Service Interval: 80 hrs.  
a)  
b)  
Stop engine, wait for all moving parts to stop, and remove key.  
Remove cooling shroud clean-out covers (Kohler) or cooling shrouds  
(Kawasaki Air-cooled) from engine and clean cooling fins. Also clean dust,  
dirt and oil from external surfaces of engine which can cause improper  
cooling.  
c)  
Make sure cooling shroud clean-out covers or cooling shrouds are  
reinstalled. Operating the engine without cooling shroud clean-out covers  
or cooling shrouds will cause engine damage due to overheating.  
5.1.21 Check spark plugs:  
Service Interval: 160 hrs.  
a)  
Remove spark plugs, check condition and reset gaps, or replace with new  
plugs. See Engine Owners Manual.  
5.1.22 Change fuel filter:  
Service Interval: As Required  
a)  
A fuel filter is installed between the fuel tanks and the engine. Replace  
when necessary.  
For Kohler engines use Kohler P/N 2405002.  
For Kawasaki engines use Kawasaki P/N 49019-7001  
5.1.23 Change hydraulic system filter:  
Service Interval: After First 250 hrs.  
Then yearly thereafter  
NOTE: Use only Exmark Part No. 1-513211 for Summer use above 32° F  
(0°C) or Part No. 1-523541 for Winter use below 32° F (0°C).  
a)  
b)  
c)  
Stop engine, wait for all moving parts to stop, and remove key.  
Locate filter under right rear corner of engine deck.  
Carefully clean area around filter. It is important that no dirt or  
contamination enter hydraulic system.  
d)  
Unscrew filter to remove and allow oil to drain from reservoir.  
- 30 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT: Before reinstalling new filter, fill it with Mobil 1 15W-50 and  
apply a thin coat of oil on the surface of the rubber seal.  
Turn the filter clockwise until rubber seal contacts the filter adapter then  
tighten the filter an additional 2/3 to 3/4 turn.  
e)  
f)  
Fill reservoir as stated in Section 5.1.11.  
Raise the rear of machine up and support with jack stands (or equivalent  
support) just high enough to allow drive wheels to turn freely.  
g)  
Start engine and move throttle control ahead to full throttle position. Move  
the speed control levers to the full speed and run for several minutes. Shut  
down machine and recheck oil level.  
Do not change hydraulic system oil (except for what can be drained when  
changing filter), unless it is felt the oil has been contaminated or been  
extremely hot.  
Changing oil unnecessarily could damage hydraulic system by  
introducing contaminates into the system.  
5.1.24 Wheel hub - slotted nut torque specification.  
When tightening the slotted nut on the wheel motor tapered shaft:  
a)  
b)  
Torque the slotted nut to 125 ft. lbs (169 N-M).  
Check distance from bottom of slot in nut to inside edge of hole. Two  
threads (0.1”) or less should be showing.  
c)  
If more than two threads (0.1”) are showing remove nut and install washer  
(PN 1-523157) between hub and nut.  
d)  
e)  
Torque the slotted nut to 125 ft. lbs (169 N-M)  
Then tighten the nut until the next set of slots line up with the cross hole in  
the shaft.  
f)  
Replace cotter pin.  
Note: Do not use antiseize on the wheel hub.  
5.1.25 Fuel Tank – mounting hardware specification.  
When installing the nuts onto the fuel tank studs, fully tighten the nyloc nut and  
back off 1/2 turn. This allows for normal fuel tank expansion and contraction with  
changes in temperature and fuel levels.  
5.1.26 Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut Type”  
are used on the following fasteners:  
a)  
b)  
c)  
d)  
e)  
f)  
Pump drive sheave setscrews.  
Square head setscrews on Hydro pump control arms.  
Sheave retaining bolt in the end of engine crankshaft.  
Caster wheel spacer nuts (See Section 5.1.16)  
Fuel tank bulkhead fitting threads.  
Cutter housing spindle nut  
Adhesives such as “Loctite RC/609 or RC/680” or “Fel-Pro Pro-Lock Retaining I  
or Retaining II” are used on the following:  
b)  
Fuel tank studs where studs are inserted into tank.  
5.1.27 Mobil HTS grease (or food-grade antisieze) is used in the following locations:  
a)  
b)  
c)  
Between the cutter housing spindle and bearings.  
Between the cutter housing spindle and sheave.  
Under top cutter housing bearing guard.  
- 31 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.1.28 Dielectric grease is used on all blade type electrical connections to prevent  
corrosion and loss of contact.  
5.2 ADJUSTMENTS  
IMPORTANT: Disengage PTO, shut off engine, wait for all moving parts to stop,  
and remove key before servicing, cleaning or making adjustments to the unit.  
5.2.1  
Cutting Height Adjustment.  
a)  
b)  
c)  
Stop machine and move drive levers out to neutral lock position.  
Disengage PTO.  
Raise the deck lever to the transport position (also the 4.5” (11.4 cm)  
cutting height position). See Figure 9.  
NOTE: When changing cutting height positions, always come to a  
complete stop and disengage the PTO.  
FIGURE 9  
CUTTING HEIGHT POSITION  
d)  
e)  
f)  
Insert height adjustment pin into hole corresponding to desired cutting  
height and install hairpin cotter. See decal on deck lift plate.  
Move lever out of transport (or 4.5” (11.4 cm) cutting height) position and  
down onto height adjustment pin to mow at selected height.  
To transport, move lever back up to transport (or 4.5” (11.4 cm) cutting height)  
position.  
g)  
Adjust anti-scalp rollers for Normal Operating Conditions. Place rollers in one  
of the positions shown in Figure 10. Rollers will maintain 3/4 in. (19 mm)  
clearance to the ground to minimize gouging and roller wear or damage.  
For Maximum Deck Flotation, place rollers one hole position lower.  
Rollers should maintain 1/4 in. (6.4 mm) clearance to ground. Do Not  
adjust rollers to support the deck. Be sure roller bolts and nuts are  
installed with the spring disc washer between head of the bolt and  
mounting bracket.  
Two types of anti-scalp roller assemblies are available. See Figure 10 to  
determine which assembly has been installed on the unit. Torque  
hardware as specified, or loss of roller may result.  
Type A – Torque the 3/8 whizlock nut to 40-45 ft-lbs. (54-61 N-m)  
Type B – Torque the 3/8 nyloc nut to 30-35 ft-lbs. (41-47 N-m)  
Torque the 3/8-24x2 Gr 8 hex capscrew to 50-55 ft-lbs (68-75 N-m)  
- 32 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE 10  
ANTI-SCALP ROLLER ADJUSTMENT  
5.2.2  
Deck Leveling:  
a)  
b)  
Position mower on a flat surface.  
Stop engine, wait for all moving parts to stop, and remove key.  
c) Check tire pressure in drive tires. Proper inflation pressure for tires is 13 psi  
(90 kPa). Adjust if necessary.  
Semi-Pneumatic caster tires do not need to be inflated.  
d)  
e)  
Set anti-scalp rollers to top holes or remove them completely for this  
adjustment.  
Raise the deck to the 4.5” (11.4 cm) height position and take as much force  
as possible off of the two large deck lift springs by loosening the nuts at the  
front of each spring. See Figure 11.  
f)  
Lower the deck to the 1-1/2” (3.8 cm) height position. Place two 1-5/16”  
(3.3 cm) thick blocks under the rear edge of the cutting deck skirt; one on  
each side of the cutting deck. Place a 1-1/8” (2.9 cm) block under the  
center front edge, but not under the anti-scalp roller brackets.  
g)  
For units with a socket head adjusting screw and slotted hole in rear deck  
lift arm: Loosen the two (2) top chain bolts in slots in the rear deck lift  
arms. Loosen jam nuts and back off the socket head adjusting screws on  
the bottom of the arms until the chains are just loose when pressure is  
applied to force rear deck support arms down. See figure 11. Continue to  
press down on rear deck support arms and turn the socket head adjusting  
screws in until slack is taken out of each chain. Tighten the jam nuts.  
Tighten the chain bolts in the deck lift arms making sure they do not move  
while tightening.  
h)  
i)  
For units without a socket head adjusting screw and slotted hole in rear  
deck lift arm: Loosen the two (2) bottom chain bolts in slots at the rear of the  
cutting deck. Press down on the rear deck support arm (as shown in Figure  
11). While holding the rear deck support arm down, take the slack out of the  
rear chains and tighten hardware at the bottom of the rear chains.  
Loosen four (4) nuts which secure front swivels (two per side), until front  
chains are loose and front of deck is supported by the 1-1/8” (2.9 cm)  
block. Do not loosen front chain hardware.  
- 33 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
j)  
On left side, adjust front swivel using the locking nut behind the swivel until  
the front chain is tight and all slack is removed from linkage. Do not lift  
front of deck off 1-1/8” (2.9 cm) block. Secure front swivel using locking  
nut in front of swivel. Repeat for right side.  
FIGURE 11  
SWIVEL ADJUSTMENT  
SPRING COMPRESSION ADJUSTMENT  
k) Recheck that blocks fit just snugly under the deck skirt and that the tension  
on all the chains are approximately equal. Make sure all chain attachment  
bolts are tight.  
l) Raise deck lift lever to the 4.5” (11.4 cm) cutting height position (also  
transport position, See Figure 9. Adjust spring compression until proper  
distance is obtained between the two washers (See Figure 11) by turning  
the nut at the front of each spring. Lock nuts in position with jam nuts.  
m) Reposition anti-scalp rollers and tighten securely.  
NOTE: When above adjustments have been made, the front of  
the deck will be slightly lower than the rear of the deck.  
5.2.3  
Pump Drive Belt Tension.  
Self-tensioning - No adjustment necessary.  
Deck Belt Tension.  
5.2.4  
5.2.5  
Self-tensioning - No adjustment necessary.  
Adjust Seat Switch.  
a) If necessary, adjust the seat actuator rod length to where the machine will  
shut off when the operator raises off the seat (with brake disengaged or  
PTO engaged) but will continue to run with operator in seat (a slight shift in  
weight should not shut machine off). Normal adjustment is when length of  
spring is 2.09” (5.3 cm ) (with seat up).  
NOTE: To prevent rough ground cut-outs the unit is equipped with a  
time delayed seat switch. When the operator raises off the seat with  
either the brake disengaged or the PTO engaged, the engine should  
stop after 1/2 second has elapsed.  
b) To adjust seat switch, loosen lock nut on bottom of the actuator rod (5/16 x 7”  
bolt) and adjust the nuts to move the actuator plate up or down on the rod.  
5.2.6  
Brake Link Adjustment.  
Check to make sure brake is adjusted properly.  
a) Disengage brake lever (lever down).  
- 34 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b) Measure the length of the spring. Measurement should be 2.75” (7.0 cm)  
between washers (see Figure 12).  
c) If adjustment is necessary, tighten the lock nut directly below the yoke and  
loosen the two nuts jammed together below the spring. Turn the nut directly  
below the washer until the correct measurement is obtained. Tighten the  
two jam nuts below the spring together and repeat on opposite side of unit.  
FIGURE 12  
BRAKE ADJUSTMENT  
5.2.7  
Brake Adjustment.  
a) Check for brake link 2.75” (7.0 cm) measurement as described in section 5.2.6.  
b) Engage brake lever (lever up).  
c) Measure the distance between the trunion roller and the rod collar as shown  
in Figure 9A. Measurement should be 3/16” (4.8 mm) to 1/4” (6.4 mm) (See  
Figure 12). A 3/16” or 1/4” square key works well as a shim gauge.  
d) If adjustment is necessary, loosen the nut directly below the yoke. Turn the  
bottom nut(below washer) until the correct measurement is obtained (See  
Figure 12) turn nut clockwise to lengthen the gap (screws rod into yoke) and  
turn counter-clockwise to shorten the gap (screws rod out of yoke). Tighten nut  
against yoke and check opposite side of unit, repeat if necessary.  
5.2.8  
Adjust Throttle Lever Tension.  
a) Stop engine, wait for all moving parts to stop, and remove key.  
b) Tension in throttle lever can be adjusted by adjusting the tightness of the  
lever pivot bolt, which is located under the console. See Figure 13.  
FIGURE 13  
THROTTLE TENSION  
5.2.9  
Electric Clutch Adjustment:  
No adjustment necessary.  
5.2.10  
Reverse Indicator Adjustment:  
a) Stop engine, wait for all moving parts to stop, and remove key.  
b) Unhook seat latch and tilt seat forward.  
- 35 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
c) Begin with either the left or right motion control lever. Move lever to the  
neutral position and pull lever back until the clevis pin (on arm below pivot  
shaft) contacts the end of the slot (just beginning to put pressure on  
spring), See Figure 14.  
d) Check where lever is relative to notch in console (should be centered  
allowing lever to pivot outward to the neutral lock position).  
e) If adjustment is needed, loosen the nut against the yoke and while applying  
slight rearward pressure on the motion control lever, turn the head of the  
adjustment bolt in the appropriate direction until lever is centered (keeping  
rearward pressure on the lever will keep the pin at the end of the slot and  
allow the adjustment bolt to move the lever to the appropriate position).  
Tighten lock nut.  
f) Repeat on opposite side of unit.  
Motion control linkage adjustment.  
5.2.11  
WARNING  
POTENTIAL HAZARD  
Engine must be running and drive wheels must be  
turning so motion control adjustment can be performed.  
WHAT CAN HAPPEN  
Contact with moving parts or hot surfaces may cause  
personal injury.  
HOW TO AVOID THE HAZARD  
Keep fingers, hands, and clothing clear of rotating  
components and hot surfaces.  
CAUTION  
POTENTIAL HAZARD  
Raising the mower deck for service or maintenance  
relying solely on mechanical or hydraulic jacks could be  
dangerous.  
WHAT CAN HAPPEN  
The mechanical or hydraulic jacks may not be enough  
support or may malfunction allowing the unit to fall,  
which could cause injury.  
HOW TO AVOID THE HAZARD  
DO NOT rely solely on mechanical or hydraulic jacks for  
support. Use adequate jack stands or equivalent  
support.  
a) This adjustment must be made with the drive wheels turning. First raise the  
frame and block up so that drive wheels can rotate freely.  
b) Remove the electrical connection from the seat safety switch, located directly  
to the left of the seat switch assembly beside the hydraulic oil reservoir.  
Temporarily install a jumper wire across the terminals in the connector of  
the wiring harness.  
c) Run the unit at least 5 minutes with the drive levers at full forward speed to  
bring hydraulic system oil up to operating temperature.  
d) Unhook seat latch and tilt seat forward.  
e) Loosen lock nuts from the ball joints at each end of the RH pump control  
linkage (See Figure 14).  
- 36 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: The nuts to the rear of the unit on each rod have left-hand threads.  
REVERSE  
INDICATOR  
TURN BOLT  
HERE  
END OF  
SLOT  
LOOSEN  
HERE  
YOKE  
TURN HERE  
TO ADJUST  
LOOSEN HERE  
(RIGHTHAND THREAD)  
LOOSEN HERE  
(LEFTHAND THREAD)  
FIGURE 14  
RH MOTION CONTROL ADJUSTMENT  
f) Start engine. Brake must be engaged and motion control levers out to  
start engine. Operator does not have to be in the seat because of the  
jumper wire being used. Run engine at full throttle and release brake.  
g) The reverse indicator spring must be correct before the following  
adjustments can be made. See Section 5.2.10.  
NOTE:The motion control lever needs to be in neutral while making  
any necessary adjustments.  
The left rod assembly controls the left wheel and the right rod assembly  
controls the right wheel.  
h) Bring the RH motion control lever into the neutral position. Adjust RH pump  
control rod length by rotating the double nuts on the rod in the appropriate  
direction until the wheels slightly creep in reverse. (See Figure 14). Move  
the motion control lever to the reverse position and while applying slight  
pressure to the lever, allow the reverse indicator spring to bring the levers  
back to neutral. The wheel must stop turning or slightly creep in reverse.  
When adjustment is complete, tighten lock nuts onto ball joints.  
i)  
Bring the LH motion control lever into the neutral position. Adjust the LH  
pump control rod length by rotating the tracking adjustment knob in the  
appropriate direction until the wheels slightly creep in reverse. Move the  
motion control lever to the reverse position and while applying slight  
pressure to the lever allow the reverse indicator spring to bring the levers  
back to neutral. The wheel must stop turning or slightly creep in reverse.  
See Figure 15.  
FIGURE 15  
LH MOTION CONTROL ADJUSTMENT  
- 37 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
j) Shut off unit. Remove jumper wire from wire harness connector and plug  
connector into seat switch.  
5.2.12  
Caster pivot bearings pre-load adjustment.  
a) Remove dust cap from caster and tighten  
nyloc nut until washers are flat and back  
off 1/4 of a turn to properly set the pre-  
load on the bearings. If disassembled  
make sure the spring washers are  
reinstalled as shown in Figure 16.  
FIGURE 16  
CASTER ADJUSTMENT  
5.2.13  
Seat armrest adjustment.  
a) Lift armrest on seat. Locate square tab  
marked with the numbers 1 through 4.  
Rotate square tab 1/4 turn to raise or  
lower the armrest in approximately 1/4”  
(6.4 mm) increments. See Figure 17.  
Armrest Adjustment  
Tab Rotate ¼ Turn  
FIGURE 17  
ARMREST ADJUSTMENT  
6. WASTE DISPOSAL  
6.1 MOTOR OIL DISPOSAL  
Engine oil and hydraulic oil are both pollutants to the environment. Dispose of used oil at  
a certified recycling center or according to your state and local regulations.  
6.2 BATTERY DISPOSAL  
DANGER  
POTENTIAL HAZARD  
Battery electrolyte contains sulfuric acid, which is  
poisonous and can cause severe burns  
WHAT CAN HAPPEN  
Swallowing electrolyte can be fatal or if it touches skin  
can cause severe burns.  
HOW TO AVOID THE HAZARD  
Wear safety glasses to shield eyes, and rubber gloves  
to protect skin and clothing when handling electrolyte.  
Do not swallow electrolyte.  
Federal law states that batteries should not be placed in the garbage. Management and  
disposal practices must be within relevant federal, state or local laws.  
If a battery is being replaced or if the unit containing the battery is no longer operating  
and is being scrapped, take the battery to a local certified recycling center. If no local  
recycling is available, return the battery to any certified battery reseller.  
- 38 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. TROUBLE SHOOTING  
7.1 MOWER PULLS LEFT OR RIGHT (W/LEVERS FULLY FORWARD).  
a) Refer to Tracking Adjustment Section 4.1.3.  
b) Check air pressure in drive tires; 13 psi.  
Semi-pneumatic casters do not require inflation.  
c) Check reverse indicator and motion control linkage adjustment. See  
Section 5.2.10 and 5.2.11.  
7.2 MOWER CUTS UNEVENLY.  
a) Check air pressure in drive tires; 13 psi.  
Semi-pneumatic casters do not require inflation.  
A more uniform cutting height may be obtained with higher tire pressure on  
rough terrain. A lower tire pressure provides more flotation.  
b) Check deck support chains.  
c) Check deck leveling (See Adjustments Section 5.2.2.)  
Note: The front of the mower deck will be approximately 1/4” (6.4 mm)  
lower than the back of the mower deck. This is the “rake” of the deck.  
d) Check blades tip to tip for straightness (they should be within 3/16" (4.8  
mm) or one blade width from being in line.)  
7.3 ENGINE WILL NOT START.  
a) Make sure battery is at a full charge.  
b) Be sure the throttle control is midway between the “SLOW” and “FAST”  
positions, and the choke is in the “ON” position for a cold engine or the  
“OFF” position for a warm engine.  
c) Make sure there is fuel in the fuel tank and that the fuel valve is open.  
d) Be sure the seat switch is properly adjusted. See Section 5.2.5.  
e) Make sure the parking brake is set and motion control levers are moved  
out (neutral lock position).  
f) Check that the PTO is disengaged.  
h) Check that the spark plug wires are properly connected.  
i) Check for loose or faulty wiring connections.  
j) Check for corrosion at all wiring connections. Even minor corrosion may  
cause a faulty connection. Clean connector terminals thoroughly with  
electrical contact cleaner, apply dielectric grease and reconnect.  
NOTE: When disconnecting electrical connectors DO NOT pull on the wires  
to separate the connectors.  
NOTE: After carefully checking the above steps, attempt to start the engine. If  
it does not start, contact your authorized Exmark service dealer.  
IMPORTANT: It is essential that all operator safety mechanisms be  
connected and in proper operating condition prior to mower use.  
When a problem occurs, do not overlook the simple causes. For example,  
starting problems could be caused by an empty fuel tank.  
The following table lists some of the common causes of trouble. Do not attempt  
to service or replace major items or any items that call for special timing of  
adjustments procedures (such as valves, governor, etc.). Have this work done  
by your Engine Service Dealer.  
- 39 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ENGINE TROUBLESHOOTING TABLE  
FAULTY  
SPARK  
PLUG  
BLOCKED  
FUEL  
FILTER  
INCORRECT  
OIL  
LEVEL  
DIRTY  
AIR  
SCREEN  
NO  
FUEL  
IMPROPER  
FUEL  
DIRT IN  
FUEL LINE  
DIRTY AIR  
FILTER  
ENGINE  
OVERLOADED  
PROBLEM  
Will not start  
Hard starting  
Stops suddenly  
Lacks power  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Operates  
erratically  
X
X
X
X
X
X
Knocks or pings  
Skips or misfires  
Backfires  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Overheats  
X
High fuel  
consumption  
X
X
X
X
- 40 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. ELECTRICAL DIAGRAM – KAWASAKI UNITS  
- 41 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELECTRICAL DIAGRAM – KOHLER UNITS  
- 42 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. HYDRAULIC DIAGRAM  
- 43 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10.  
2-Year Limited Warranty  
Exmark Turf Equipment  
(For units purchased on or after October 1, 2004)  
Conditions and Products Covered  
Owner’s Responsibilities  
Exmark Mfg. Co. Inc. and its affiliate, Exmark Warranty  
Company, pursuant to an agreement between them, jointly  
warrant on the terms and conditions herein, that we will repair,  
replace or adjust any part manufactured by Exmark and found  
by us (in the exercise of our reasonable discretion) to be  
defective in factory materials or workmanship for a period of  
two years.  
The Exmark turf equipment, including any defective part,  
must be returned to an authorized Exmark service dealer  
within the warranty period. This warranty extends only to  
turf equipment operated under normal conditions. You  
must properly service and maintain your Exmark product  
as described in the operator’s manual. Such routine  
maintenance, whether performed by a dealer or by you, is  
at your expense.  
This warranty applies to Exmark turf equipment purchased on  
or after October 1, 2004 sold in the US or Canada. This  
warranty may only be assigned or transferred to a second (or  
third) owner by an authorized Exmark dealer. The warranty  
period commences upon the date of the original retail  
purchase.  
As a condition to this warranty, customer shall have read  
the operator's manual and shall have completed and  
submitted to Exmark Warranty Company, within the  
prescribed time, the Exmark warranty registration.  
General Conditions  
Products  
Warranty Period  
2 years  
The sole liability of Exmark and Exmark Warranty Company  
with respect to this warranty shall be repair and replacement  
as set forth herein. Neither Exmark nor Exmark Warranty  
Company shall have any liability for any other cost, loss  
or damage, including but not limited to, any incidental  
or consequential loss or damage.  
All Products (except as noted below)  
All Attachments and Accessories  
Metro 21 Series  
1 year  
1 year  
Belts and Tires  
90 days  
Battery  
Engine*  
1 Year Prorated  
In particular, we shall have no liability or responsibility for:  
Warranty is covered by engine manufacturer  
Expenses related to gasoline, oil or lubricants.  
Travel time, overtime, after hours time or other  
extraordinary repair charges or charge relating to  
repairs or replacements outside of normal business  
hours at the place of business of the authorized  
Exmark service dealer.  
*Please refer to the engine manufacturer’s warranty statement  
that is included in the literature packet. We are not authorized  
to handle warranty adjustments on engines.  
This warranty only includes the cost of parts and labor.  
Rental of like or similar replacement equipment  
during the period of any warranty, repair or  
replacement work.  
Any telephone or telegram charges or travel charges.  
Loss or damage to person or property other than that  
covered by the terms of this warranty.  
Any claims for lost revenue, lost profit or additional  
cost as a result of a claim of breach of warranty.  
Attorney's fees.  
Items and Conditions Not Covered  
This warranty does not cover the following:  
Pickup and delivery charges to and from any authorized  
Exmark Service Dealer.  
Any damage or deterioration due to normal use, wear  
and tear, or exposure.  
Cost of regular maintenance service or parts, such as  
filters, fuel, lubricants, tune-up parts, and adjustments.  
Any product or part which has been altered or misused  
or required replacement or repair due to normal wear,  
accidents, or lack of proper maintenance.  
Any repairs necessary due to use of parts, accessories  
or supplies, including gasoline, oil or lubricants,  
incompatible with the turf equipment or other than as  
recommended in the operator's manual or other  
operational instructions provided by Exmark.  
No Claim of breach of warranty shall be cause for  
cancellation or rescission of the contract of sale of any  
Exmark mower.  
There are no understandings, agreements, representations,  
or warranties, express or implied, including but not limited to  
any regarding the merchantability (that product is fit for  
ordinary use) or fitness for use (that product is fit for a  
particular purpose), not specified herein, respecting the  
equipment which is the subject of this warranty.  
All warranty work must be performed by an authorized Exmark  
Service Dealer using Exmark approved replacement parts.  
Instructions for Obtaining Warranty Service  
1. Contact any Exmark Service Dealer to arrange service at  
their dealership. To locate a dealer convenient to you,  
may also call 402-223-6375.  
Some states do not allow exclusions of incidental or  
consequential damages, or limitations on how long an  
implied warranty lasts, so the above exclusions and  
limitations may not apply to you.  
2. Bring the product and your proof of purchase (sales  
receipt) to the Exmark Service Dealer.  
This warranty gives you specific legal rights, and you may  
also have other rights which vary from state to state.  
If for any reason you are dissatisfied with the Service Dealer’s  
analysis or with the assistance provided, contact us at:  
Exmark Customer Service Department  
The Exmark Warranty Company  
2101 Ashland Avenue  
Beatrice, NE 68310  
402-223-6375 or  
- 44 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE RECORD  
Date  
Description of Work Done  
Service  
Done By  
- 45 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
- 46 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEE EXMARK’S COMPLETE  
LINE OF ACCESSORIES  
RIDING ACCESSORIES  
CUSTOM RIDE SEAT SUSPENSION SYSTEM  
DECK LIFT ASSIST KIT  
HITCH KIT  
LIGHT KIT  
MICRO-MULCH SYSTEM  
ROLL OVER PROTECTION SYSTEM (ROPS)  
SNOW BLADE  
SUN SHADE  
TRASH CONTAINER  
TURF STRIPER  
ULTRA VAC COLLECTION SYSTEM  
ULTRA VAC QUICK DISPOSAL SYSTEM  
WALK BEHIND ACCESSORIES  
GRASS CATCHER  
MICRO-MULCH SYSTEM  
STEERABLE SULKY  
SULKY HITCH KIT  
TURF STRIPER  
Check us out on the Web:  
WARNING  
The engine exhaust from this product  
contains chemicals known to the State of  
California to cause cancer, birth defects, or  
other reproductive harm.  
© 1997-2005 EXMARK MFG. CO. INC.  
INDUSTRIAL PARK BOX 808  
BEATRICE, NE 68310  
PART NO. 103-9182  
(402) 223-6300  
FAX (402) 223-5489  
®
ALL RIGHTS RESERVED  
PRINTED IN U.S.A.  
MFG. CO. INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Drill EDR 260 User Manual
Extron electronic Network Cables 3192M User Manual
Field Controls Humidifier z100 User Manual
Fusion Car Amplifier En 1502 User Manual
Gefen Cable Box GEF HDMI13 2 3GSDI User Manual
Gemini Turntable CDM 3600 User Manual
GE Oven ZSC2000 User Manual
GE Washer G132 User Manual
Global Upholstery Co Computer Hardware 3307568 User Manual
Goldstar Microwave Oven MA 2005ST User Manual