Euro Pro Carpet Cleaner EP95B User Manual

OWNER’S MANUAL  
Steam Blaster  
Model EP95B  
Congratulations! You are the owner of the ultimate in modern Vapor Steam  
Cleaning equipment. To fully enjoy the advantages of your appliance, please  
take a few minutes to read all the “Owner’s Manual” and keep the instructions  
handy for ready reference. Please review the product warranty and mail the  
owner registration form.  
For information or assistance:  
EURO-PRO Operating LLC  
94 Main Mill Street, Door 16  
Plattsburgh, NY 12901  
Tel.: 800-798-7398  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USAGE SUGGESTIONS FOR SHARK STEAM BLASTER  
IMPORTANT SAFETY INSTRUCTIONS  
When using your Shark Steam Blaster, basic safety precautions should always  
be observed, including the following:  
Important User Information  
To reduce the risk of fire, electric shock, or  
injury:  
1. Read all instructions before using your  
Shark Steam Blaster.  
2. Use the system only for its intended use.  
3. To protect against a risk of electric shock,  
do not immerse any part of the system in  
water or other liquids.  
4. Never yank cord to disconnect from  
outlet; instead, grasp plug and pull to  
disconnect.  
5. Do not allow cord to touch hot surfaces.  
Let the system cool completely before  
putting away. Use “Cord Storage Hooks” for  
power cord.  
Please note that this steam cleaner has a “flow through injection” type boiler  
and is not a pressurized system. It will take approximately 45-90 seconds for  
the steam injector to heat up and the “steam ready light” to go off. Once the  
steam ready light has gone off, push the steam switch on the handgrip to the  
“On” position (I) in order to start the steam flow. Steam power will steadily  
increase during the first four (4) minutes of use, after which time steam output  
will stabilize. Some steam will condense around the floor brush when in use  
and will cause hard surfaces to become wet during the cleaning process, this  
is normal.  
Do not leave the Shark Steam Blaster  
plugged in when unattended. Unplug the  
electrical cord when not in use and before  
servicing or refilling water tank.  
Do not allow to be used as a toy. Close  
attention is necessary when used by or near  
children, pets or plants.  
Use only as described in this manual. Use  
only manufacturer’s recommended  
accessories.  
Do not pull cord, use cord as a handle, close  
a door on cord, or pull cord around sharp  
edges or corners. Keep cord away from  
heated surfaces.  
6. Always disconnect system from electrical  
outlet when filling or emptying water tank  
and when not in use.  
Tips On How To Use Your  
System  
Water  
• Using scented fabric softener while  
washing the towels will cause the  
scent to be released into the air when  
using the towels with your steam  
Do not use extension cords or outlets with  
inadequate current carrying capacity.  
Turn off all controls as applicable before  
unplugging from electrical outlet.  
Do not unplug by pulling on cord. To unplug,  
grasp the plug, not the cord.  
Do not handle plug or steam cleaner with wet  
hands or operate without shoes.  
Do not put any objects into openings. Do not  
use with any opening blocked.  
Store your appliance indoors in a cool, dry  
area.  
Keep your work area well lit.  
When in use, never turn the appliance over  
or on its side. Never direct steam towards  
people, animals or plants.  
Do not immerse the steam cleaner into water  
or other liquids. Always unplug the power  
cord from the electrical socket when filling the  
steam cleaner.  
7. Do not operate the system with a damaged  
cord or plug, or if the appliance or any other  
part of the system has been dropped or  
damaged. To avoid the risk of electric  
shock, do not disassemble or attempt to  
repair the Shark Steam Blaster. Return  
the system to EURO-PRO Operating LLC  
(see warranty) for examination and repair.  
Incorrect re-assembly or repair can cause a  
risk of electrical shock or injury to persons  
when the Shark Steam Blaster is used.  
8. Close supervision is necessary for any  
appliance being used by or near children.  
Do not leave the system unattended while  
connected.  
9. Burns can occur from touching hot metal  
parts, hot water or steam. Do not turn  
upside down as there may be hot water in  
the unit. Never direct steam at any person.  
The steam is very hot and can cause burns.  
10. Do not operate in the presence of  
explosive and/or flammable fumes.  
11. This appliance is intended only for  
household use. Follow all user instructions  
in this manual.  
Use tap water for all your cleaning  
needs, however, if you live in an area  
with hard water, use  
system.  
Wood, Vinyl and Marble Floors  
Use the floor brush with a 100% cotton  
terry cloth attached, ( see page 7 for  
details). Move the brush slowly in back  
and forth motions. When the towel is  
soiled, you can turn the towel over or  
replace it with a clean towel. If you are  
working on a very dirty area, we  
recommend that you move the brush  
over the area slowly, several times. If it  
is a wood floor, do NOT leave the unit  
stationary for any length of time to avoid  
heat or moisture build-up in the wood.  
By cleaning with the towel over the  
brush, you will not affect the shine on the  
floor.  
To Clean Waxed Floors: Install a clean  
towel(s) on the floor brush, work quickly.  
The towel will absorb the dirt but not  
remove the wax.  
Vinyl Floors: Do not allow heat to buildup  
in any kind of vinyl, since it can soften it  
enough to affect its texture. Work quickly  
on vinyl. Use two (2) towels on floor brush.  
demineralized/distilled water.  
Important: Do NOT add cleaning  
solutions, scented perfumes, oils or any  
other chemicals to the water used in  
this appliance. Use tap water or  
distilled/purified water if the tap  
water in your area is very hard.  
Temperature  
• The vapor temperature at the tip of  
the nozzle is between 220°F and 240°F.  
• The temperature of the vapor falls to  
100 °F at a distance of 10 inches from  
the nozzle.  
CAUTION: A towel wrapped around the  
brush can become hot enough to burn.  
Make sure that you let the towel cool off  
before touching it or changing it.  
Do NOT add cleaning solutions, scented  
perfumes, oils or any other chemicals to  
the water used in this appliance as this  
may damage the unit or make it unsafe for  
use. Use tap water or distilled/purified  
water if the tap water in your area is very hard.  
Using Towels  
12. Never use any chemicals or substance  
other than tap water in the machine. Use of  
chemicals may damage the machine. Use  
of chemicals will automatically void your  
warranty.  
Note: We strongly recommend the  
use of two (2) 100 % cotton towels  
layered one on top of the other.  
• For best results use 100% cotton white  
terry cloth towels.  
• Use correct size (8” x 17”) of towel to  
allow you to wrap the towel over the  
ends of the brush and clip it under the  
spring loaded towel clips.  
• The purpose of using towels is to  
absorb the moisture and dirt being  
removed. Always use dry towels. A  
wet towel will smear the dirt.  
• Wash towels with strong detergent  
and bleach.  
Tile Floors: For tile and marble floors only,  
if there is an area of the floor which is  
excessively dirty, you may remove the  
towels and agitate the area with the brush  
bristles directly. Do not let the area dry.  
Wipe immediately with a clean cloth. Re-  
clean with brush and towels in place.  
SAVE THESE INSTRUCTIONS  
Note: Do not use steam cleaner on  
hardwood or vinyl floor without towels  
installed on the floor brush.  
For Household Use Only  
8
1
Rev. 04/02C  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADDITIONAL IMPORTANT SAFEGUARDS cont.  
OPERATING INSTRUCTIONS cont.  
Attaching a Towel to the  
Floor Brush  
100% white terry cloth towel can be fitted  
on this brush, so as to absorb the dirt and  
protect delicate surfaces.  
1. To avoid circuit overload, do not operate  
Warning: Always keep unit in upright  
another appliance on the same socket  
position when in use. Do not lie flat on  
(circuit) when using this unit.  
the floor or turn upside down when in  
2. If an extension cord is absolutely  
use. Inverting the unit or placing flat on  
necessary, a 15 ampere 14 gage cord  
the floor may cause hot water to exit  
from the hose and cause injury.  
should be used. Cords rated for less  
Important: Please note that bristles may  
break through thin towels. We recommend  
that two (2) towels, laid one on top of the  
other be used. This will ensure that the  
brush bristles do not break through and  
that the towels will be sufficiently absorbent  
and retain as much dirt as possible.  
amperage may overheat. Care should be  
taken to arrange cord so that it cannot be  
pulled or tripped over.  
Fig. C  
Note: We recommend that you drain  
the water tank after every use.  
3. Do not leave unattended when the system  
is connected to a power supply/electrical  
outlet.  
4. Fold the other side of the towel as  
shown in Fig. C.  
Very Important: When installing the  
towels to the floor brush, ensure that the  
towels do not cover the front and the back  
of the brush. (See fig. E)  
Caution: Upon initial use, the steam will be mixed with water,  
hot enough to scald. Ensure that the floor brush is  
resting on the floor or the hose handgrip is directed  
away from user when steam switch is turned on. Never  
direct the nozzle or brush end of the unit toward  
yourself or anyone near you.  
Important User Information  
Fig. D  
Please note that this steam cleaner has a “flow through injection” type  
boiler and is not a pressurized system. It will take approximately 45-90  
seconds for the steam injector to heat up and the “steam ready light” to go  
off. Once the steam ready light has gone off, push the steam switch on the  
handgrip to the “On” position (I) in order to start the steam flow. Steam  
power will steadily increase during the first four (4) minutes of use, after  
which time steam output will stabilize. Some steam will condense around  
the floor brush when in use and will cause hard surfaces to become wet  
during the cleaning process, this is normal.  
5. Place the corner under the cloth  
holder as shown in Fig. D.  
Fig. A  
1. Prepare white terry cloth towel:  
size 8” x 17” as shown in Fig. A.  
Open  
2. Place the brush on top of the towel.  
Warning: This appliance is equipped with a grounded-type  
3-wire cord (3-prong plug). This plug will only fit into  
an electrical outlet made for a 3-prong plug. This is a  
safety feature. If the plug should fail to fit the outlet,  
contact an electrician to replace the outlet. Do not  
attempt to defeat the safety purpose of the  
Open  
Fig. E  
grounding pin, part of the 3-prong plug.  
6. Place the towel around the brush,  
and repeat folding the towel as shown  
in Fig. E. When folding the towel,  
leave some slack. Do not pull tightly  
around the brush, leave some  
looseness.  
Fig. B  
3. Fold the towel as shown in Fig. B  
SAVE THESE INSTRUCTIONS  
FOR HOUSEHOLD USE ONLY  
2
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING INSTRUCTIONS cont.  
GETTING TO KNOW YOUR SHARK STEAM BLASTER  
ON/OFF STEAM SWITCH  
1.  
Before turning the steam switch to the  
Steam On/Off  
Switch  
“On” position, wait until the “Steam  
Ready” light located on the unit has  
turned off.  
1
2.  
Setting this switch to the “On” position will  
start the flow of steam.  
CAUTION:  
Upon initial use, the steam will be mixed with  
water, hot enough to scald. Ensure that the  
floor brush is resting on the floor or the hose  
handgrip is directed away from user when  
steam switch is turned on. Never direct the  
nozzle or brush end of the unit toward yourself  
or anyone near you.  
2
3
CAUTION:  
The “On/Off Steam Switch” located on the  
handle must be in the “Off” position before  
attaching or disassembling accessories.  
Never leave the “Steam Switch” in the “On”  
position when unit is not in use.  
4
Glass & Tile Squeegee  
This attachment is very useful for cleaning  
large windows, plastic material, ceramic,  
tiled surfaces, marble planes, etc.  
Apply steam abundantly, rub with the  
spongy side of squeegee and remove with  
the glass wiping rubber located at the front  
edge of squeegee.  
1. Reservoir cover  
2. On/Off Switch  
3. Steam Ready Light (Green)  
4. Pivoting Wheels  
Technical Specifications  
Features  
• On/Off Switch  
• Thermostat & Safety  
Thermofuse  
• Steam Trigger on Handgrip  
• Steam Ready Light  
• 3 Pivoting Wheels  
Detail Cleaning Attachment  
Voltage:  
Power:  
120V~ 60Hz.  
1400 Watts  
This attachment is very useful for cleaning  
surfaces that are difficult to reach. It is ideal for  
radiators, door and window jambs, shutters and  
sanitary fixtures. The following parts can be  
applied to this attachment:  
Water Capacity:  
3 1/4 Cups (.8 L.)  
Max. Steam Temp.: 240°F  
6
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
GETTING TO KNOW YOUR SHARK STEAM BLASTER  
cont.  
OPERATING INSTRUCTIONS  
PREPARATION FOR USE  
This appliance cleans many types of hard surfaces with the force of steam without any  
need for chemical cleaning products Obviously, it is also the ideal solution in particular  
situations such as removing wall-paper, washing windows and degreasing many hard  
surfaces in and around the home.  
WARNING: ALWAYS unplug the appliance prior to any type  
of maintenance on the unit. As all the appliances are  
thoroughly tested before sale, there may be some residual  
water in the boiler.  
ASSEMBLY & OPERATION  
To connect the tube and the accessories (fig. 1), insert part  
(A) in part (B) turning this slightly to facilitate insertion. Make  
sure that key (C) is securely fastened in the hole provided (D).  
Open the reservoir cover (1) and pour in 3 1/4 cups  
(.8 liters) of tap water or distilled water if your tap water is  
particularly hard. Never add cleaning fluids. Close the  
reservoir cover (1). Before plugging in the appliance, make  
sure that you have assembled the tubes and accessories  
correctly and the steam switch on handgrip is “Off”. Press the  
on/off switch (2) to “On”; the steam ready light (3) will come  
on; when the light (3) switches off (after about 1 minute), you  
can start to use the appliance. To spray steam, simply press  
the steam switch button on the handle (6) (fig. 2).  
IMPORTANT INFORMATION  
Before using the appliance make sure that the materials or the surfaces to be  
cleaned can withstand a temperature of 212° F (100ºC). The steamer is  
equipped with a safety device that, in the case of a fault, vents the steam  
from the bottom of the appliance.  
5
6
2
When there is no more steam, fill the tank again. To avoid  
damage, never use the steam gun without water. If the tank is  
full and no steam is sprayed, have the appliance checked by  
the manufacturer. Always switch off the appliance after use,  
pull out the plug and drain any residual water from water tank.  
1
3
4
Important User Information  
Please note that this steam cleaner has a “flow through  
injection” type boiler and is not a pressurized system. It  
will take approximately 45-90 seconds for the steam  
injector to heat up and the “steam ready light” to go off.  
Once the steam ready light has gone off, push the steam  
switch on the handgrip to the “On” position (I) in order to  
start the steam flow. Steam power will steadily increase  
during the first four (4) minutes of use, after which time  
steam output will stabilize. Some steam will condense  
around the floor brush when in use and will cause hard  
surfaces to become wet during the cleaning process, this  
is normal.  
STANDARD ACCESSORIES  
1. THE HOSE includes the steam switch (6) (see page 6) on the handle.  
All the accessories clip onto this and can be removed by pressing the lock key.  
2. THE EXTENSIONS (2) are connected to each other and to the handle of the  
hose. They extend the range of action and reach of the appliance and assure a  
more comfortable working position.  
3. THE BRUSH provided is the ideal accessory for cleaning hardwood, vinyl, tile  
and marble floors. Two clamps are provided to fasten the cloth towels to the  
brush.  
4. THE CONCENTRATOR makes it possible to clean in even the tightest corners  
(toilet, taps, joints between tiles); the concentrated jet of steam is able to  
remove stubborn, ingrained dirt.  
NOZZLE CLEANING INSTRUCTIONS  
Your steamer should not normally require cleaning, however,  
should you notice a marked decrease in steam output it may  
be necessary to remove mineral deposit build-up from the  
nozzle orifice. First ensure that there is water in the tank.  
If tank is empty, fill with water, (we recommend using purified  
or mineral water), then re-start unit noting whether steam  
output is normal. If steam output is still low, follow these cleaning instructions:  
1. Unplug steam cleaner from wall outlet.  
2. Use a small diameter stiff metal wire such as a straightened metal paperclip  
and carefully insert the end of the wire into the nozzle orifice.  
3. Move wire back and forth several times to remove any deposits.  
4. Reconnect appliance to power outlet, switch on and note steam output.  
5. If steam performance does not improve, repeat steps #1 through #4.  
5. THE DETAIL BRUSH is combined with the concentrator by inserting  
over the tip of the concentrator.  
6. THE WINDOW SQUEEGEE has two rubber edges, a scrubber edge and  
wiping edge, for cleaning windows and mirrors. When cleaning outside  
windows, always avoid any sudden changes in temperature to prevent  
breakage or cracks.  
FOR CONSTANT EFFICIENCY OF THE APPLIANCE, REMEMBER TO  
CLEAN ALL ACCESSORIES AND THE STEAM SUPPLY NOZZLES  
REGULARLY  
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.  

Earthquake Sound Speaker SUB100 User Manual
Fender Musical Instrument 112 User Manual
Friedrich Air Conditioner AIR CONDITIONER CEILING SUSPENSION TYPE P N9362292054 User Manual
Frigidaire Microwave Oven FGMV173K User Manual
GBC Binding Machine TL300 User Manual
GE Air Conditioner AGH06 User Manual
GE Dishwasher PDWT500 580R User Manual
Gefen Switch EXT DVIKVM 841DL User Manual
Generac Power Systems Automobile Parts 0D9727 User Manual
Genesis Advanced Technologies Saw GTS10S User Manual