E Series
DHD675-E/DWU675-E/DHD775-E/DWU775-E
U S E R M A N U A L
020-000515-01
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICES
COPYRIGHT AND TRADEMARKS
© 2013 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of
their respective holders.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of the product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at the user’s own expense.
WARNING! Changes or modifications not expressly approved by Christie could void the user’s
authority to operate the product.
FOR COMMERCIAL USE ONLY - POUR USAGE COMMERCIAL UNIQUEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING 2 CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
CET APPAREIL NUMÉRIQUE DE CLASSE A EST CONFORME AUX NORMES DÉFINIES
DANS LES RÉGLEMENTATIONS CANADIENNES SUR LES APPAREILS CAUSANT
DES INTERFÉRENCES RADIO (CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS, ICES-003, CLASS A).
,
.
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products
or availability could occur which may not be reflected in this document. Christie reserves the right
to make changes to specifications at any time without notice. Performance specifications are
typical, but may vary depending on conditions beyond Christie's control such as maintenance of
the product in proper working conditions. Performance specifications are based on information
available at the time of printing. Christie makes no warranty of any kind with regard to this material,
including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not
be liable for errors contained herein or for incidental or consequential damages in connection with
the performance or use of this material.
The product is designed and manufactured with high-quality materials and components that can
be recycled and reused. This symbol
means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from regular waste. Please dispose of the product
appropriately and according to local regulations. In the European Union, there are separate
collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!
Canadian manufacturing facility is ISO 9001 and 14001 certified.
GENERAL WARRANTY STATEMENTS
For complete information about Christie’s limited warranty, please contact your Christie dealer. In
addition to the other limitations that may be specified in Christie’s limited warranty, the warranty
does not cover:
a. Damage occurring during shipment, in either direction.
b. Projector lamps (See Christie’s separate lamp program policy).
c. Damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp
supplied by a supplier other than Christie.
d. Problems caused by combination of the product with non-Christie equipment, such as distribution
systems, cameras, video tape recorders, etc., or use of the product with any non-Christie interface
device.
e. Damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or
other natural disaster.
f. Damage caused by improper installation/alignment, or by product modification, if by other than a
Christie authorized repair service provider.
g. For LCD projectors, the warranty period specified applies only where the LCD projector is in “normal
use.” “Normal use” means the LCD projector is not used more than 8 hours a day, 5 days a week.
For any LCD projector where “normal use” is exceeded, warranty coverage under this warranty
terminates after 6000 hours of operation.
h. Failure due to normal wear and tear.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your
product. Please see the Maintenance section for specific maintenance items as they relate to your
product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specified by Christie, will void the warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1. SAFETY
2. INTRODUCTION
2.1 Projector Components..................................................................................................2-1
2.2 Built-in Keypad .............................................................................................................2-3
2.3 Input/Output (I/O) Panel ...............................................................................................2-4
2.4 Remote Control ............................................................................................................2-5
2.5 LED Status Indicators...................................................................................................2-7
3. INSTALLATION
3.1 Connect to Computer ...................................................................................................3-1
3.2 Connect to Video Equipment........................................................................................3-2
3.3 Turn the Projector On...................................................................................................3-3
3.4 Turn the Projector Off...................................................................................................3-3
3.5 Adjust the Projector Position ........................................................................................3-4
3.6 Calculate Lens Offset ...................................................................................................3-5
3.7 Removing and Installing the Lens ................................................................................3-9
3.8 Ceiling Mount Installation .............................................................................................3-10
3.9 Stacking Installation......................................................................................................3-11
3.9.1 Adapter Plate Installation.....................................................................................3-11
3.9.2 Stacking...............................................................................................................3-11
3.9.3 Stacking Multiple Projectors ................................................................................3-12
3.9.4 Stacking Alignment..............................................................................................3-13
4. OPERATION
4.1 Size and Position Menu................................................................................................4-2
4.2 Image Settings Menu....................................................................................................4-7
4.3 Configuration Menu ......................................................................................................4-10
4.4 Lamp Menu...................................................................................................................4-16
4.5 Status Menu .................................................................................................................4-18
4.6 Input Switching & PIP Menu.........................................................................................4-19
4.7 Language Menu............................................................................................................4-21
4.8 Test Pattern Menu........................................................................................................4-21
4.9 Web User Interface.......................................................................................................4-22
4.9.1 Logging On..........................................................................................................4-22
4.9.2 Main Tabbed Page – General .............................................................................4-22
4.9.3 Main Tabbed Page – Status................................................................................4-23
4.9.4 Main Tabbed Page – Lens ..................................................................................4-23
4.9.5 Network ...............................................................................................................4-24
4.9.6 Tools....................................................................................................................4-26
4.9.7 Administrator Page..............................................................................................4-27
4.9.8 About Page..........................................................................................................4-27
4.10 Christie Presenter.........................................................................................................4-28
4.10.1 Connect to the Projector and Download Christie Presenter Software...............4-28
4.10.2 Install Christie Presenter software.....................................................................4-30
4.10.3 Use Christie Presenter ......................................................................................4-31
4.11 Card Reader Operation ................................................................................................4-36
4.12 Install the Lamp ............................................................................................................4-40
E Series User Manual
i
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
5. TROUBLESHOOTING
6. SPECIFICATIONS
6.1 Inputs............................................................................................................................6-1
6.2 PIP/PBP Compatibility..................................................................................................6-2
6.3 Key Features ................................................................................................................6-3
6.4 List of Components.......................................................................................................6-4
6.5 Optional Accessories....................................................................................................6-4
6.6 REGULATORY.............................................................................................................6-5
6.7 Declaration of Conformity for EU Countries .................................................................6-7
6.8 Federal Communications Commission (FCC) Warning................................................6-7
6.9 MENU TREE.................................................................................................................6-8
ii
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Safety
1.
SAFETY
Read through this document in its entirety and understand all warnings and
precautions before attempting to operate the projector.
WARNING
Do not look into the projector lens when the lamp is on. The bright light
may result in permanent eye damage.
y
y
To reduce the risk of fire or electric shock, do not expose this projector to
rain or moisture.
Do not open or disassemble the projector as this may cause electric shock.
y
y
When replacing the lamp, allow the projector to cool, and follow all
replacement instructions.
When you turn the projector off, wait 90 seconds for the projector to cool
down before you disconnect the projector from power.
y
y
Cooling the lamp during the ignition phase may lead to ignition failures.
After a successful lamp ignition, keep the lamp burning for at least 15
minutes to maintain lamp life.
When the lamp is approaching the end of its life, the message “Lamp is
approaching the end of its useful life in full power operation” appears on
the screen. Change the lamp when the warning message appears.
y
All installation and maintenance procedures must be performed by a
Christie accredited service technician.
y
y
y
Keep all combustible material away from the concentrated light beam of
the projector.
Position all cables where they cannot contact hot surfaces or be pulled or
tripped over.
E Series User Manual
1-1
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Safety
Always power down the projector and disconnect all power sources before
servicing or cleaning.
y
y
y
y
Use a soft cloth moistened with a mild detergent to clean the display
housing.
Disconnect the power plug from the AC outlet if the product is not being
used for an extended period of time.
Operate the projector under the following conditions:
-
-
-
-
Operating temperature range: 5°C to 35°C
Storage temperature range: -10°C to 60°C
Humidity range: 5% to 80 % RH (Max.), non condensing
Operating altitude: 10,000 ft. maximum
Use only the AC power cord supplied. Do not attempt operation if the AC
supply and cord are not within the specified voltage and power range for
your region.
y
y
Remove the lens plug from the lens opening in the projector before
installing the lens. Retain the lens plug to protect the optical components
from dust and debris during transport.
Do not block the ventilation slots and openings on the projector.
Do not use abrasive cleaners, waxes or solvents to clean the projector.
Do not allow anything to rest on the power cord.
y
y
y
1-2
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Introduction
2.
INTRODUCTION
The product specified in this document is a high brightness, high-resolution
video/graphics 1-chip mercury lamp based projector. The projector is available
in HD and WUXGA resolutions. The projector utilizes Digital Light Processing
(DLP®) technology from Texas Instruments. It is primarily designed for fixed
installation markets.
2.1
Projector Components
Vista frontal
1
2
3
4
5
Vista posterior
6
7
8
9
10
E Series User Manual
2-1
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Introduction
Ind.
1
Part Name
Description
Lens door
Use the lens door to access the lens module.
Receives signals from the IR remote. Keep the signal
path to the sensor unobstructed for uninterrupted
communication with the projector.
2
Front IR Sensor
Allows automated lens control and adjustment: vertical
and horizontal offsets, zoom and focus.
3
4
Projection Lens
Keep these vents unobstructed to prevent the projector
from overheating.
Cooling Air Vents
5
6
7
8
Adjustable Feet
Raise or lower the feet to level the projector.
Displays the status of the projector. They are (from left
to right): LAMP 1, LAMP 2, STATUS and PIC MUTE.
LED Status Indicators
Rear IR Sensor
Receives signals from the IR remote. Keep the signal
path to the sensor unobstructed for uninterrupted
communication with the projector.
Lamp Door (Screws) Use the lamp to access to the lamp module.
9
Built-in Keypad
Controls the projector.
Input/Output (I/O)
Panel
10
Connects the projector to external devices.
2-2
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Introduction
2.2
Built-in Keypad
1
2
3
4
6
7
8
9
5
10
Ind.
1
Key Name
Power
Description
Turn the projector on or off.
2
Menu
Auto
Lens
Focus
Exit
Display menus
3
Automatically optimize image
Adjust the lens vertical or horizontal offset setting
Adjust focus
4
5
6
Return to previous level or exit menus if at top level
Adjust a setting UP or DOWN
Navigate within a menu
y
y
7
Arrow Keys
8
Input
Select an input for the main or PIP/PBP image
Display or blank the video image
Adjust zoom
9
Picture Mute
10 Zoom
E Series User Manual
2-3
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Introduction
2.3
Input/Output (I/O) Panel
1
2
3
4
5
6
7
8
9
10
11
12
13
14 15 16 17 18 19 20
Ind.
1
Connector Name
S-Video
Ind.
2
Connector Name
CVBS
Ind.
3
Connector Name
Red/Pr
4
Blue/Pb
5
Green/Y
USB
6
RS232 IN
Ethernet
7
Mini USB
8
9
10 Remote
13 VGA-IN
11 Display Port
14 HDMI-1
12 VGA-OUT
15 HDMI-2
16
R
17
20
G
V
18
B
19 H/C
2-4
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Introduction
2.4
Remote Control
1
2
3
4
5
16
17
18
19
20
6
7
21
22
8
9
23
24
10
25
11
26
27
12
13
14
28
15
29
E Series User Manual
2-5
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Introduction
Ind.
1
Key Name
Description
Display or blank the video image
Turn projector ON
Picture Mute
Power on
Gamma
Bright
2
3
Adjust mid-range levels
4
Adjust amount of light in the image
Turn PIP/PBP ON/OFF
5
PIP/PBP
Size
6
Adjust the PIP/PBP size
7
Number Keys
Help
Enter a number, such as a channel, value, etc
Display context-sensitive help
Display menus
8
9
Menu
Adjust a setting UP or DOWN
Navigate within a menu
y
y
10 Arrow Keys
11 Test
Display a test pattern
12 Auto
Automatically optimize image
Use to hide or show menus
13 OSD
14 Keystone H
15 Keystone V
16 Standby
17 Contrast
18 Hot-key
19 Swap
Adjust the horizontal keystone
Adjust the vertical keystone
Turn projector OFF
Adjust difference between dark and light
Select your preset keys quickly
Swap the main and PIP/PBP images
Adjust the PIP/PBP layout
20 Layout
21 Focus
22 Zoom
Adjust focus to improve image clarity as desired
Adjust zoom to achieve a desired image size
Change the remote ID. Press Proj Key then a number
between 1 and 9 to assign an ID. Press PROJ then
number 0 to return to the universal remote ID.
23 Proj Key
24 Exit
Return to previous level or exit menus if at top level
Select a highlighted menu item
Change or accept a value
y
y
25 Enter
26 Input
27 Info
Select an input for the main or PIP/PBP image
Display source image information
Horizontal Lens Shift - Adjust the position of the image
horizontally
28 Lens H
Vertical Lens Shift - Adjust the position of the image
vertically
29 Lens V
2-6
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Introduction
2.5
LED Status Indicators
The LED status indicators are located on the rear of the projector.
LAMP 1 LED
y
LED Status
Projector State
Failed to strike lamp after 5 attempts (strike attempts will
stop).
Red (short blink)
Yellow (no blink)
Lamp has unexpectedly shut down (system goes into
cool down state).
Lamp time has expired and lamp should be replaced.
(projector also begins to display the replace lamp On
Screen Display message at startup).
Green (no blink)
Green (short blink)
Off
Lamp 1 turn ON ok
Projector is switching to Lamp 1 (Lamp 2 is off)
(selected by OSD menu “Current Lamp”: 1/ 2/ Both )
Lamp is off
LAMP 2 LED
LED Status
y
Projector State
Failed to strike lamp after 5 attempts (strike attempts will
stop).
Red (short blink)
Yellow (no blink)
Lamp has unexpectedly shut down (system goes into
cool down state).
Lamp time has expired and lamp should be replaced.
(projector also begins to display the replace lamp OSD
message at startup).
Green (no blink)
Green (short blink)
Off
Lamp 2 turn ON ok
Projector is switching to Lamp 2 (Lamp 1 is off)
(selected by OSD menu “Current Lamp”: 1/ 2/ Both )
Lamp is off
E Series User Manual
2-7
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Introduction
STATUS LED
y
LED Status
Off
Projector State
Projector is in OFF state (without AC plug in)
Projector is in standby mode (AC plug in)
Projector is in startup state
Yellow (no blink)
Yellow long blink
Yellow long blink
Projector is in cool down state
Flashing Green/
Yellow
Projector is in flash update state
Flashing Red
Red (no blink)
Fan failure
Over-temperature
Green (blink very
quickly)
Projector communications (Read/Write EEPROM)
Projector is powered up and operating normally
Green (no blink)
PICTURE MUTE LED
y
LED Status
Green
Projector State
Picture mute is off – image is displayed
Picture mute is on – image is black
Yellow (no blink)
2-8
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
3.
INSTALLATION
3.1
Connect to Computer
Desktop
Laptop
MOLEX
9
1
2
3
4
6
7
8
5
x e l
o
m
Ind.
Connector Name
Ind.
2
Connector Name
Ind.
3
Connector Name
1
4
VGA out Cable
VGA in Cable
RS232 Cable
Mini USB to USB A Type
Cable
WiFi USB Dongle or thumb
drive
5
6
9
Network Cable
Displayport Cable
7
HDMI to DVI Cable
8
Power Cord
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
™
™
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
™
E Series User Manual
3-1
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
3.2
Connect to Video Equipment
DVD player
Component video output equipment
Video cassette recorder
6
4
1
2
3
8
9
4
7
5
Ind.
1
Connector Name
S-Video Cable
Ind.
Connector Name
Ind.
3
Connector Name
2
Composite Video Cable
HDMI Cable
3 RCA Component
Cable
15-Pin to 3 RCA Component/
HDTV Adaptor
4
7
5
6
9
VGA to RGB SCART
Power Cord
8
VGA in Cable
RCA-BNC Cable
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
™
™
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
™
3-2
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
3.3
Turn the Projector On
1. Ensure that the power cord and signal cable are securely connected. The
1
Power button on the built in keypad is illuminated.
“
”
“
”
2. Turn on the lamp by pressing
on the remote control or press
on
2
the built-in keypad. The STATUS LED is yellow and LAMP LED is green
with a long blink.
The startup screen displays in approximately 10 seconds.
3. Turn on the source. Select Input Key on the remote control to select
an input source (VGA, BNC, HDMI1, HDMI2, Component, S-Video or
3
Composite Video).
4. The projector detects the source you selected and displays the image.
NOTE:
The first time the projector is used, the preferred language may be selected from the main menu after the startup screen is
™
displayed.
2
Power on
1
Status LED
2
3
Power on
Input Key
3.4
Turn the Projector Off
“
”
1. Press
on the built-in keypad or on the remote control to turn off the
projector. A warning message will appear on the displayed image.
“
”
“
”
2. Press
again to confirm your selection. If you do not press
again,
the warning message will disappear after 10 seconds.
E Series User Manual
3-3
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
3.5
Adjust the Projector Position
When you select a position for the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Follow these general guidelines:
Position the projector on a flat surface at a right angle to the screen. The
projector (with the standard lens) must be at least 3 feet (0.9m) from the
projection screen.
y
Position the projector to the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting, and
the video format determine the size of the projected image.
y
For the fixed short lens, the image exits at a default angle. However, the
lens shift feature makes the image offset variable.
y
y
Lens throw ratio:
-
-
-
-
-
Lens 0.8:1 Fixed Short (Zero offset)
Lens 1.2-1.5:1 Fixed Short
Lens 1.5-2.0:1 Zoom
Lens 2.0-4.0:1 Zoom
Lens 4.0-7.0:1 Long Zoom
Do not roll the projector more than 20 degrees from side to side.
Do not put the projector on either side to project an image.
y
y
20°
20°
360 degree operation (alone the widest axis)
y
360°
3-4
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
3.6
Calculate Lens Offset
The vertical image offset (shift) ranges for the projector are +120%/-40%
(WUXGA) and +134%/-40% (HD). Offset is +720 pixels for both WUXGA
and HD. The horizontal image offset is +/-20% (+/- 192 pixels).
y
NOTE:
™
The 0.8:1 lens is the only exception and must be used on axis.
The method for calculating lens offset complies with Industry standards.
Example for Vertical lens offset:
y
-
At 0% offset (or on axis), the center of the image is on the lens center,
so that half of the image appears above and half appears below the
lens center.
-
-
At +100% offset, all (or 100%) of the image will appear above the lens
center.
The % offset is calculated as the ratio of the number of pixels shifted
up/down to half the image size. Examples for WUXGA:
Shifting up 600 pixels gives offset of 600/600 * 100% = 100%
Shifting down 600 pixels gives offset of -600/600 * 100% = -100%
Shifting up 720 pixels gives offset of 720/600 * 100% = 120%
Shifting up 240 pixels gives offset of 240/600 * 100% = 40%
`
`
`
`
WUXGA Projectors:
Vertical Image Offset: 0% Offset (WUXGA)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
600 pixels
above lens
center.
Lens center
600 pixels
below lens
center.
E Series User Manual
3-5
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
Vertical Image Offset: 120% Offset (WUXGA)
Image has been offset 720 pixels above lens
center, so the center of the image is now 720
pixels above where the center of the image
was at 0% offset (or lens center).
The offset is
+720/600 * 100% = +120%.
720 pixels
of shift
above lens
center.
Lens center
Vertical Image Offset: -40% Offset (WUXGA)
Image has been offset 240 pixels below lens
center, so the image has an offset of
-240/600 * 100% = -40%
240 pixels
of shift
Lens center
below lens
center.
Total of
840 pixels
(600+240)
of display
are below
lens center.
3-6
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
HD Projectors:
Vertical Image Offset: 0% Offset (HD)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
540 pixels
above lens
center.
Lens center
540 pixels
below lens
center.
Vertical Image Offset: 134% Offset (HD)
Image has been offset 720 pixels above lens
center, so the center of the image is now 720
pixels above where the center of the image
was at 0% offset (or lens center).
The offset is
+720/540 * 100% = +134%.
720 pixels
of shift
above lens
center.
Lens center
E Series User Manual
3-7
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
Vertical Image Offset: -40% Offset (HD)
Image has been offset 216 pixels below lens
center, so the image has an offset of
-216/540 * 100% = -40%
216 pixels
of shift
Lens center
below lens
center.
Total of
756 pixels
(540+216)
of display
are below
lens center.
Horizontal Image Offset: +/-20% Offset
-192 pixels
1920 pixels
+192 pixels
Image has been offset 192 pixels
left or right of lens center.
The image has an offset of
+192/960 * 100% = +20%, or
-192/960 * 100% = -20%
3-8
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
3.7
Removing and Installing the Lens
When handling the projector after lens installation, make sure the front lens cap is
placed on the lens to protect the lens surface from potential damage. When carrying
or moving the projector, do not handle by the lens. This may damage the lens, the
chassis or other mechanical parts within the projector.
1. Center the lens: Ensure that the lens is at or near its center position. Attempting to
remove the lens when at a large offset may cause damage to the lens assembly. Center
the lens while the projector is switched on by pressing the lens horizontal or vertical
button and then pressing Enter.
2. Turn Off the projector: Turn the projector OFF and disconnect the power cord.
3. Allow the projector to cool down to Standby mode before replacing the lens.
4. Remove the lens: Push and open the lens door located on the top-front of the projector.
5. Push the release lever up to release the lock. Remove the lens through the front of the
projector.
6. Remove the rear lens cap from the lens. Keep the front lens cap on the lens to protect it
during installation.
7. Install the new lens: Align the lens interface plate with the lens mount. Fully insert the
assembly straight into the lens mount without turning.
Push the release lever down to lock the lens in place.
8. Lower the Lens Door and slide back into the secured position.
E Series User Manual
3-9
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
3.8
Ceiling Mount Installation
The projector can be inverted and suspended from the ceiling using a specially
designed ceiling mount fixture. For more information, contact your dealer.
Use only the Christie approved ceiling mount kit (133-106108-02) designed
for your projector.
y
y
When not mounted properly, the projector may fall, causing hazards or
injury. The warranty on this projector does not cover any damage caused
by the use of any non-recommended ceiling mount kit or installation of the
ceiling mount kit in an improper location.
Refer to the installation instructions and safety guidelines provided in the
kit.
y
3-10
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
3.9
Stacking Installation
3.9.1 Adapter Plate Installation
When stacking E Series projectors, an adapter plate is required to install the E
Series unit into the stacking frame.
1. Turn the projector OFF and disconnect the AC power cord after the cooling
fans have stopped.
2. Place the projector top-side down on a clean and flat surface.
3. Line up the mounting holes of the adapter plate (133-107109-02) with the
mounting holes on the baseplate of the projector.
4. Secure the adapter plate with 4 M6x25 flathead screws. Torque to 41 in-lb.
Adapter Plate Attachments
Bottom View
Mounting
All attachment
points to be
secured
3.9.2 Stacking
The E Series projectors can be stacked up to a maximum of 3 projectors high
using the Christie stacking frame (118-100107-01).
Description
1) Base Plate
2) Locking pin
3) Cable Tie-off Frame
4) Stacjing Leg
5) Locking Nut
+/- Roll
6) Knob
+/- Pitch
= 50 Ibs (22.68 kg)
+/- Yaw
Frame Weight
Adapter Plate Weight = 3.26 Ibs (1.48 kg)
Projector Weight = 43 Ibs (19.50 kg)
Lens Weight (up to) = 5.43 Ibs (2.46 kg)
Up to = 101.69 Ibs (46.12 kg)
(per projector and frame)
E Series User Manual
3-11
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
Install the adapter plate on the E Series projector (described in 3.9.1) before
mounting to the stacking frame.
1. Make sure the pitch is to its maximum, prior to placing the projector from
the front.
2. Place the projector into the stacking frame.
NOTE: There are two ways of placing the projector into the stacking frame: from the top or from the
front.
3. Make sure the bottom base plate of the frame is aligned with the projector.
4. Use a 6 mm Allen key to tighten the (6) M8 bolts securing the base plate to
the bottom of the stacker adapter plate.
Stacking Frame Attachments
3.9.3 Stacking Multiple Projectors
NOTE: The projectors can be stacked and hoisted in either an upright or inverted positions.
1. With one person positioned on each side of
the stacking frame, lift the top stacking frame
onto the bottom stacking frame, aligning all
four stacking legs between the frames.
NOTE: Remove the locking pin from each stacking leg prior to alignment
and ensure the four stacking legs are fully seated on the lower stacking
frame.
™
1450.50 mm
Step 2 is a critical safety procedure
that MUST be observed. Failure to
engage the locking pin may cause
the projectors to separate, resulting in
possible injury or death.
DANGER
980.00 mm
3-12
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Installation
2. Insert the locking pin through the holes in the stacking legs. Make sure
each pin is fully inserted.
NOTE: The steel ball on the end of the pin keeps the pin from releasing inadvertently.
™
Hole
Stacking
Leg
Pin
Inserted
Press botton to
remove or install
the pin
Pin
Steel Ball
3. When required, repeat steps 1 and 2 for the third projector in the stack.
3.9.4 Stacking Alignment
Stacked projectors must be correctly aligned to one another so the resulting
display is optimized. If hoisting the stack, do so first and then align. To align
the image, use pitch, yaw, or roll. Prior to aligning the image, turn the locking
nut to unlock then use the knob to adjust the image.
NOTE: Ensure to lock the locking nut to maintain the image adjustment.
™
Pitch
Adjustment moves the
image up and down
LOCKING
KNOB
NUT
Roll
Rotates the image clockwise
and counter-clockwise
+/- Roll
Pitch
Adjustment moves the
image left and right
+/- Pitch
+/- Yaw
Note: If the projector is parallel to the screen, some keystone will
be introduced with pitch and yaw adjustment.
E Series User Manual
3-13
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.
OPERATION
The projector has multilingual On-Screen Display (OSD) menus that allow you
to make image adjustments and change a variety of settings.
•
Most of the projector controls are accessed from within the projector menu
system. There are several groups of related functions, with each group
selectable from the Main menu as shown below. Press the MENU button on
the remote control or on the built-in keypad on the rear of the projector to
display the main menu.
•
•
•
•
Use the arrow keys to navigate within the menu and adjust a setting up or
down.
Press ENTER to select a highlighted menu item or use it to change or
accept a value.
Select the next item that you want to adjust in the menu and adjust it as
described above.
Press EXIT to return to the previous menu or exit menus if at top level.
E Series User Manual
4-1
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.1
Size and Position Menu
Size Presets
Display an image with the detected size, or resize the image by maximizing
either the height, width or both, or resize to the maximum size possible while
keeping the original aspect ratio.
Auto: Display with the detected size.
y
y
y
y
y
y
y
Native: Display in its native resolution.
4:3: Retain 4:3 aspect ratio.
Letterbox: Display with the black borders on the top and bottom.
Full Size: Fill the screen (regardless of the source).
Full Width: Fill display width and keep aspect ratio.
Full Height: Fill display height and keep aspect ratio.
Overscan
Remove noise around the image. The ZOOM range can be from 50% to 400%
Pixel Track
Analog RGB signals only. Steady flickering or several soft vertical stripes
or bands across the entire image indicates poor pixel tracking. Proper pixel
tracking ensures that the image quality is consistent across the screen, the
aspect ratio is maintained, and that the pixel phase can be optimized.
4-2
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Pixel Phase
Analog RGB signals only. Adjust pixel phase when the image still shows
shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the
phase of the pixel-sampling clock relative to the incoming signal.
Horz Position
Move the image right or left within the area of available pixels.
Vert Position
Move the image up or down within the area of available pixels.
Digital Horz Zoom
Change the size of projector's display area horizontally. If the display area
has been resized by this setting, it can be moved by changing the Digital Horz
Shift and Digital Vert Shift settings.
Digital Vert Zoom
Change the size of projector's display area vertically. If the display area has
been resized by this setting, it can be moved by changing the Digital Horz
Shift and Digital Vert Shift settings.
Digital Horz Shift
Move the display area horizontally if its size has been changed by the Digital
Zoom setting.
Digital Vert Shift
Move the display area vertically if its size has been changed by the Digital
Zoom setting.
Geometry Correction
The "Geometry Correction" can be controlled with the options in the drop-
down list: "Off/Basic" when optional Dual Processor Warp Module is not
installed, and "Off/Basic/Curve/Rotate" when optional Dual Processor Warp
Module is installed.
Geometry Correction Feature Compatibility
Curved
Surface(2x2)
Pincushion
and Barrel
Warp Function
4-Corner
4-Corner
--
Keystone
Rotation
P
--
P
X
P
X
P
X
Curved
Surface(2x2)
P
P
P
P
Keystone
Pincushion
and Barrel
Rotation
X
--
X
P
--
X
X
P
X
X
X
--
E Series User Manual
4-3
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Off: No Geometric correction is applied to the image.
y
y
Horz Keystone: Adjust the keystone horizontally and make a more square
image. Horizontal keystone is used to correct a keystoned image shape
in which the left and right borders of the image are unequal in length, and
the top and bottom are slanted to one of the sides. This is intended for use
with horizontally on-axis applications. For horizontally offset applications,
you must use 4 Corner correction using the optional Dual Processor Warp
Module.
9%
9%
17%
17%
Vert Keystone: Adjust the keystone vertically and make a more square
image. Vertical keystone is used to correct a keystoned image shape in
which the left and right borders of the image are unequal in length, and
the top and bottom are slanted to one of the sides. This is intended for use
with horizontally on-axis applications. For horizontally offset applications,
you must use 4 Corner correction using the optional Dual Processor Warp
Module.
y
3%
5%
5%
3%
Horz Pincushion: Adjust the pincushion horizontally and make a more
square image.
y
y
11%
6%
Vert Pincushion: Adjust the pincushion vertically and make a more square
image.
8%
8%
4-4
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Pincushion/Barrel: Allow for correction for slight curved distortion from the
lens or projection surface.
y
y
8%
9%
4%
9%
4-Corner: Allow the image to be squeezed to fit an area defined by moving
each of the four corners’ x and y position.
1
2
Ind.
1
Description
8%
8%
Top Left Horz adjust.
8
3
4
2
Top Right Horz adjust.
Top Right Vert adjust.
Bottom Right Vert adjust.
Bottom Right Horz adjust.
Bottom Left Horz adjust.
Bottom Left Vert adjust.
Top Left Vert adjust.
3
7%
7%
7%
7%
4
5
7
6
8%
8%
7
6
5
8
Curve: Allow for symmetrical correction of a constant radius horizontal
or vertical curve by modifying the top and bottom of the image only.
Compound curves are not supported. Projector must be mounted
perpendicular to the chord of the curve within the offset limitation of the
lens used (ideally on axis). No tilt correction.
y
11%
11%
8%
8%
E Series User Manual
4-5
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Rotation: Allow an image to be rotated – most commonly to level the
y
image. While the image is rotated, the software can crop any content that
begins to fall off the panel. The function will not automatically scale the
image down to prevent cropping. If scaling is required, the digital zoom
function can be used, independently of the rotation function.
±8°
Auto Image
Force the projector to reacquire and lock to the input signal. This is useful
when signal quality is marginal. “Normal mode” can support all of the 4:3 input
sources.
“Wide mode” can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example
1400 x 1050), perform Auto Image using “normal mode”.
4-6
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.2
Image Settings Menu
Brightness
Adjust the intensity of the image.
Contrast
Adjust the degree of difference between the lightest and darkest parts of the
picture and change the amount of black and white in the image.
Color Space
Select a color space that has been specifically tuned for the input signal.
Useful only for analog signals and certain digital sources.
Detail
Select the edge clarity of the image.
Video Options
This function is used with video sources only.
Color: Adjust a video image from black and white to fully saturated color.
The color setting applies to video sources only.
y
Tint: Adjust the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
y
Noise Reduction: Reduce temporal or spatial noise in the image.
y
y
Flesh Tone Correction: Control the amount of flesh tone correction applied
to the image.
E Series User Manual
4-7
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Video Black Level: Analyze the current input image and calculate an offset
y
value which is then added to the analog to digital converter black level
value. This ensures optimum black level for each analog source.
Detect Film: Control film mode detection and determine whether the
original source of the input video was film or video.
y
y
Closed Captions: Control closed caption display while audio is not muted.
If this setting is not off, audio is not muted, the source is NTSC and
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
Input Levels
VGA / Component signals only.
Adjust the gain of the red, green, or blue channel of the image. It will affect
the white.
y
y
y
Adjust the offset of the red, green, or blue channel of the image. It will
affect the black and white.
Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Picture Settings
Optimize the projector for displaying images under certain conditions, such
as presentation, video, bright, whiteboard, blackboard, beige wall and user-
definable preset. It will affect Gamma, Sharpness,White Peaking, Overscan,
Brightness, Contrast, Color, Tint, Red Gain, Green Gain, Blue Gain, Red
Offset, Green Offset, Blue Offset.
Save to User
Adjust the image settings and select Save to User as a picture setting. You
can recall these settings in the future by selecting the User in the Picture
Settings menu. The setting of Brightness, Contrast, Color, Tint, Red Gain,
Green Gain, Blue Gain, Red Offset, Green Offset, Blue Offset, Color Temp,
Gamma, Detail, BrilliantColor , White Peaking and Overscan will be saved.
DynamicBlack™
Select the check box to constantly adjust the aperture based on the amount of
black in the current scene.
Image Freeze
Pause the screen image.
Advanced Image Settings
Gamma: Select the appropriate gamma from Video, Film, Bright, and CRT.
y
y
BrilliantColor™: Produce an expanded on-screen color spectrum that
delivers enhanced color saturation for bright, true-to-life images.
4-8
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
White Peaking: (video source only) Increase the brightness of whites that
are near 100%.
y
y
y
Color Temperature: Change the intensity of the colors. Select a listed
relative warmth value.
Edge Enhancement: Apply the edge enhancement process.
E Series User Manual
4-9
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.3
Configuration Menu
Language
Allows you to select an available language for the OSD display, from English,
French, German, Italian, Spanish, Chinese(simplified), Japanese, Korean, and
Russian.
Lens Settings
Focus and Zoom: Adjust the focus and zoom the image in or out.
Lens Shift: Shift the lens up and down or left and right.
y
y
y
Lock Lens Motors: Select this function to prevent all lens motors from
moving. It will disable the Zoom, Focus, Horizontal and Vertical Position
settings, effectively locking out any changes and overriding all other lens
features. This is particularly useful to prevent accidental lens position
changes in multi-projector installations.
Lens Calibration: Calibrate the lens center
y
Ceiling Mount
Turn the image upside down for ceiling-mounted projection.
Rear Projection
Reverse the image so you can project from behind a translucent screen.
4-10
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Menu Preferences
Menu Horz Position: Change the horizontal position of the OSD.
Menu Vert Position: Change the vertical position of the OSD.
Show Messages: Display status messages on the screen.
y
y
y
y
Menu Transparency: Change OSD menu background to be transparent.
NOTE:
™
As the value increases, more of the image behind the menu is visible.
Splash Screen: Choose which splash screen is to be used.
y
y
PIN Protect: The PIN (personal identification number) feature allows you
to password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image.
Change PIN: Allows you to change the PIN.
y
Power Management
Standby Mode: The projector is in standby mode when connected to AC
power. (<0.5W)
y
y
y
AC Power On: The projector automatically turns on when electrical power
is connected.
Auto Shutdown: Automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
Sleep Timer: Allows the projector to automatically power off after it has
y
been on for a specified amount of time.
High Altitude
Set high altitude mode ON/OFF. When ON, the fan will operate at high speed
to ensure sufficient air flow for high altitudes.
Communications
Network: Allow you to setup network settings.
y
-
-
-
-
-
-
-
-
-
DHCP: Turn the DHCP ON/OFF.
IP Address: Assign Network IP Address.
Subnet Mask: Assign Network Subnet Mask.
Default Gateway: Assign Network Default Gateway.
Host Name: Display the host name.
MAC Address: Displays network MAC Address value.
Show Network Messages: Turn network messages ON/OFF.
Restart Network: Restart the network.
Network Factory Reset: Perform factory reset on the network settings.
The Projector Name, LAN IP, WLAN IP, and SNMP settings will be
reset.
E Series User Manual
4-11
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Baud Rate: Select the serial port and baud rate.
y
y
y
Serial Port Echo: Control whether the serial port echoes characters.
Projector Address: Set the projector address (0-9). The projector will
respond to IR remotes set either at the same address as the projector or to
IR remotes set to address 0.
Image Blending
Adjust blend widths and settings to left, right, top and/or bottom sides to create
a seamless multi-projector stitched image. (Available only when optional Dual
Processor Warp Module is installed.)
What is a Blend?
In simple terms, a blend appears as a gradient strip along an edge of a
projected image. It is darkest along the extreme edge of the image, and
lightens nearer to the rest of the image(see below).
How are Blends used?
In multiple-projector wall, complementary blends between neighboring images
can compensate for the extra “brightness” or intensity where these edges
overlap. By controlling blend width and other properties, you can achieve
uniformity across the group of images. Visible overlaps will disappear, as
shown below
With edge blending:
Overlap
Blend
Proj. 1,1
Proj. 1,2
Proj. 1,1
Proj. 1,2
Blend
Overlap
Image
Image
Proj. 2,1
Proj. 2,2
Proj. 2,1
Proj. 2,2
Blending regions can be defined on all sides – left, right, top and bottom. The
same gamma curve is used for all blending regions.
4-12
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Color Matching
You may require a unique color gamut (range) for a single projector or
application, or you may need to precisely match colors across multiple
adjacent displays. Use Color Matching by Meter Adjustment or by Manual
Adjustment to define the precise hue of each primary color component (red,
green, blue and white).
The x/y coordinates for each color define its location on the standard CIE
chromaticity graph. Changing either or both of these numbers will change
the hue of the color, and modify the range of possible colors. For example,
changing the x/y coordinates for red may move the color closer to orange
or closer to violet, which will in turn affect all displayed colors having a red
component. Adjust the slide bars or enter new specific coordinates as desired
to define or change the color gamuts needed for your environment and
applications.
Enable the selected method (Meter or Manual Adjustment)– this will
automatically disable the other method. For both methods, if Auto Test Pattern
is enabled, the solid colored test pattern will be displayed according to the
menu item on which you are positioned.
Meter Adjustment
y
1. Using a color meter, enter the current x and y co-ordinates of Red,
Green, Blue and White for the projector image into the Measured Data
menu. This is the reference point for the projector. The default values
in the menu are based on the average for all projectors.
2. After measuring the values for all the projectors to be matched,
calculate the target values.
3. Enter the target values for x, y and gain for each color into the Target
Data menu.
E Series User Manual
4-13
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Green
Measured Data
Target Data
Red
Blue
Manual Adjustment
y
1. Adjust color slide bars and judge image color by eye or meter. A user-
defined color “adjustment” can be applied.
2. Use this submenu if you do not have specific color coordinates in
mind and will judge color performance by eye or meter. As for Meter
Adjustment, each color control actually defines new x/y coordinates for
that color and changes its hue. The main colors (red part of red, green
part of green and blue part of blue) adjust the intensity of that color
component, while the modifying colors (e.g. green part of red and blue
part of red) modify the x and y value and change the hue of that color.
At the same time the main colors also are used to control the color of
the white point.
Hot-Key Settings
Assign a different function to the hot-key on the remote control by highlighting
the function in the list and pressing ENTER. Choose a function that does
not already have a dedicated button, and assign the hot-key to that function,
allowing you to quickly and easily use the chosen function.
Service
Projector Info: Display current projector settings (read-only).
y
y
Factory Reset: Restore all settings to their default value. It will not reset
network but it will reset RS232.
Test Pattern: Choose the desired internal test pattern to display, or select
OFF to turn off a test pattern.
y
y
Color wheel Index (2x): Set Color wheel index to Speed 2X. This setting
only needs to be used when the Main Board is changed, and should be
4-14
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
adjusted to optimize picture quality.
Color wheel Index (3x): Set Color wheel index to Speed 3X. This setting
only needs to be used when the Main Board is changed, and should be
adjusted to optimize picture quality.
y
Error log: Show the projector error log for debug.
y
y
Mode Adjustment: Fine tune the H and V start position for a signal in the
EDID timing table and record the values in the system to override the
timing table. The settings must be “Saved to Record” before exiting the
menu, or they will be lost. To revert to original timing table settings, each
setting must be manually cleared. Factory Defaults will not clear these
override settings.
E Series User Manual
4-15
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.4
Lamp Menu
Lamp Mode
Select Constant Power or Constant Intensity mode.
Constant Power
Set the value of the lamp power (in Watts).
Constant Intensity
Set the value for the Constant Intensity to maintain constant brightness. A light
sensor is used to monitor the light level and will apply more power as the lamp
brightness decays naturally over time until it reaches maximum power. The
light sensor needs to be calibrated when you replace a lamp or "Reset Lamp
Hours".
Current Lamp
Select which lamp(s) is in use.
NOTE:
™
A 120 second timed lockout is applied after changing modes before you can change it again.
Eco Mode
Set Eco mode ON, OFF, Auto or assign a lamp to Eco mode. When Eco Mode
is enabled, the projector will switch to single lamp mode, adjust to the lowest
fan speed and switch the lamp power to the minimum setting.
Lamp Auto Switch
Control when the projector switches lamps. Options include: on failure only, at
4-16
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
power-up, or after a set number of hours.
Lamp Auto Switch Time
Set the number of hours for Lamp Auto Switch.
For example:
1. Lamp conditions: lamp 1 = 50 hours, lamp 2 = 60 hours.
2. Set the current lamp to lamp 1 - the lamp with the lower lamp hour
usage.
3. Set the Lamp Auto Switch to After (N) hours and the Lamp Auto
Switch Time to 100 hours.
4. When lamp 1 reaches 150 hours, projector will auto switch to lamp 2.
5. When lamp 2 reaches 160 hours, projector will auto switch to lamp 1.
Lamp Info
Display current lamp(s) settings (read-only).
Lamp Life Settings
Set the number of hours for the lamp life warning. At every startup, the lamp
hours are checked. If they exceed this value, a lamp replace message will
appear.
Reset Lamp Hours
Reset the lamp used hours counter to zero. Do this after changing the lamp.
Light Sensor
Calibrate the Light Sensor for use with the Constant Intensity lamp mode,
which allows the projector to be set for constant brightness. If the Light Sensor
has not been calibrated, Constant Intensity mode will be disabled. Light
Sensor calibration should be repeated when new lamps are installed.
E Series User Manual
4-17
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.5
Status Menu
The read-only Status menu lists a variety of details about the standard and
optional components currently detected in the projector.
4-18
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.6
Input Switching & PIP Menu
NOTE:
™
Reference the compatibility table found in Section 6.2.
Main Input
From the list of active inputs, select one to be used as the main image.
PIP/PBP Input
From the list of active inputs, select one to be used as the PIP/PBP.
PIP/PBP Enable
Toggle between displaying two sources at once (Main and PIP/PBP images)
or one source only. The check box turns the PIP/PBP source ON and OFF.
Swap
Change the main image to PIP/PBP, and the PIP/PBP to main image.
Swapping is available only when PIP/PBP is enabled.
Size
Select the PIP/PBP size to small, medium or large.
Layout
Set the location of the PIP/PBP image on the screen.
E Series User Manual
4-19
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
NOTE:
PIP/PBP layout and size table as described below.
™
™
™
P : indicates primary source region (lighter color).
* : Both source regions are the same size.
PIP/PBP Size
Medium
PIP/PBP Layout
Small
Large
P
P
P
PBP, Main left
PBP, Main Top
PBP, Main Right
PBP, Main Bottom
PIP-Bottom Right
PIP-Bottom Left
PIP-Top Left
*
*
*
*
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
PIP-Top Right
P
P
P
Timing Detection
Select timing detection mode to wide or normal. It is used to support additional
PC timings. When the projected picture is not completed, this function is used
to adjust the picture. “Normal mode” can support all of the 4:3 input sources.
“Wide mode” can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example
1400 x 1050), perform Auto Image using “normal mode”.
Source Info
Display current source settings (read-only).
Enable Source Hot-Key
Toggle the check box to enable or disable the main source hot-key.
Source Hot-Key
Allows you to assign a different source to the hot-key. Highlight an input and
press ENTER to choose a different one.
4-20
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Input Key
Use it to list all of the sources or change the sources.
4.7
Language Menu
Allows you to select an available language for the OSD display.
4.8
Test Pattern Menu
Choose the desired internal test pattern to display, or select OFF to turn off a
test pattern.
OFF
y
y
y
y
y
y
Black
White
Checkerboard
Grid
Color Bars
E Series User Manual
4-21
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.9
Web User Interface
4.9.1 Logging On
Open your web browser and type the IP address (in the address bar) assigned
to your projector.
1 Select the log in level from the Access type drop-down list
2 Enter the Password in the Password field
3 Select the appropriate language from the Language drop-down list.
4 Click the Press login button. The Main window appears.
4.9.2 Main Tabbed Page – General
Control Panel
y
Select main source / PIP source, enable/disable PIP/POP, change the
layout / PIP size, swap, and change the test pattern.
4-22
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Projector Information Panel
y
Check the projector information for power status, Pic mute status, OSD
status, IP address and Mac address.
Switch Panel
Switch the on/off status of power, Pic mute, and OSD.
4.9.3 Main Tabbed Page – Status
Display the current status of lamp info, cooling (fans), version numbers and
signal (source) information
4.9.4 Main Tabbed Page – Lens
Control the focus, lens shift and zoom adjustments for the lens.
E Series User Manual
4-23
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.9.5 Network
SettingsPage
Restart Network
y
-
Execute a network restart. This will not change any of the network
settings.
Network Factory Reset
y
Execute a network factory reset. Network settings will be reset to the
following default values:
-
-
-
Projector Name = Christie@ + Serial Number
Show Network Messages = ON
LAN Settings:
-
-
-
-
Manual
IP Address = 192.168.0.100
Subnet Mask = 255.255.255.0
Default Gateway = 192.168.0.100
-
WLAN Settings:
Enabled
-
4-24
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
-
-
-
-
Start IP = 192.168.1.100
End IP = 192.168.1.120
Subnet Mask = 255.255.255.0
Default Gateway = 192.168.1.100
-
-
SNMP Settings:
-
-
-
-
SNMP Read Communication = private
Trap IP Address = 0.0.0.0
SMTP IP Address = 0.0.0.0
All other settings are cleared/blanked
Trap Configuration:
All items = SNMP Trap + Email
LAN Panel
Enter the IP address, subnet mask, default gateway for the LAN setting
-
y
-
Select if the projector must obtain an automatically assigned IP address
through DHCP or if the user will set the address manually.
-
Enter the IP address, netmask, default gateway and DNS server
address for the TCP/IP setting
WLAN Panel
y
y
-
-
Select if Enable or Disable the WLAN function.
Enter Start IP, End IP, Subnet Mask, Default Gateway for the WLAN
setting.
SNMP Panel
- The E Series SNMP (Simple Network Management Protocol) interface
provides network administrators with a common way to manage their
network devices from a single remote location. SNMP allows an
administrator to query a number of devices to see their current status/
configuration. It also allows operators to change configuration values
and configure trap or Email notifications to be sent when certain events
occur.(eg. Loss of signal, power state change, etc)
Emails are sent to the mail server configured in the projector
settings. Up to 2 user email accounts can be selected. Any
important information regarding the event will be located in the body
content of the email.
`
SNMP Traps are notifications that are sent from the projector. They
are only received by a trap receiver (MIB Browser) in the computer.
`
-
SNMP Read Community (default setting: private) – this is a plain-
text password. This must also be entered in the MIB browser. This
password allows the various settings in the projector to be queried.
E Series User Manual
4-25
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
-
-
SNMP Location (default setting: blank) – This field can be used
as a description to where a projector is located in a building.
SNMP emails sent will specify this location.
Trap IP Address (default setting: 0.0.0.0) – This field must be
filled in to receive Traps from the projector. The Trap IP Address
should be filled in with the IP Address of the computer on which
you would like to view received traps.
-
Trap Email 1/2 (default setting: Blank) – The Trap Email 1 and 2
must be set to an email address that is configured under the mail
server that you will enter in the “SMTP Server IP Address” field.
-
-
Email from Address (default setting: blank) – the “Email from
Address” that will appear as the source of the SNMP emails.
SMTP Server IP Address (default setting: 0.0.0.0) – Enter your
mail server’s IP address.
Trap Configuration Panel
y
Set the SNMP actions for the system events. The dropdown options
are: SNMP Trap + Email, Email, SNMP Trap, and Disabled.
4.9.6 Tools
Use the Tools tabbed pages to control “Size & Position”, “Image
Settings”, “Configuration”, “Lamp”, “Input Switching & PIP” and “Test
Pattern”.
4-26
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.9.7 Administrator Page
Add or delete a user or change password
4.9.8 About Page
Version Tab
y
y
View the main firmware version, network firmware version, projector model
name, and projector serial number.
License Tab
The license information of the computer program is displayed.
E Series User Manual
4-27
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.10 Christie Presenter
The Christie Presenter application allows a remote desktop from a host PC
to be displayed on the network display through Ethernet, USB, or wireless
transports. It can adapt to different network settings (DHCP, fixed IP, and
direct link by USB/Ethernet cable).
Christie Presenter can be downloaded from the Christie website or from the
web page of the projector.
4.10.1 Connect to the Projector and Download Christie Presenter
Software
1. Connect to the projector using WiFi or Ethernet
-
Ethernet connection:
Determine the projector’s IP address from the menu Main Menu >
Configuration > Communications > LAN
`
Configure your PC IP address to be on the same network as the
projector.
`
`
The projector and computer must be connected directly or over the
network via Ethernet.
-
WiFi Wireless connection:
Insert the WiFi USB dongle (1DWUSB-BGN) into the USB port on
the projector input panel.
`
Insert the WiFi USB dongle
4-28
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Power on the Projector.
`
`
Obtain the WiFi Password from the OSD menu Main Menu >
Configuration > Communications > WLAN
Connect your PC device to the wireless SSID for the selected
projector . Example: “Christie@0112000123”.
`
Enter the password obtained from the OSD WLAN menu.
`
E Series User Manual
4-29
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.10.2 Install Christie Presenter software
1. Use a web browser to connect to the projector’s network address (Default
address 192.168.1.100)
2. Download and install the Christie Presenter Software
3. Configure the Christie Presenter Software. The name entered is used to
identify all computers connected to the projector via the Christie Presenter
software via either wired or wireless connections. The Network Display
Management -> Device Management tab will show all current connections.
4-30
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.10.3 Use Christie Presenter
1. Press the autorun icon in the system tray to pause or play the USB display.
2. After starting the Christie Presenter application, the main window can been
seen (shown below).
Icon
Description
Connect and search network display
Stop/start displaying desktop contents to
connected network display
Select display region
Configure Christie Presenter
Manage all connected network displays
Disconnect all connections
E Series User Manual
4-31
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Connect and search network display
1. Click the button to enter into the connection menu section.
2. If the IP address of the projector is known, enter the IP address and
click the "Connect" button. If the IP address is not known, click the
"Search" button to search for the projector on the network and select
the projector to which you want to connect. Select the option "Directly"
in order to proceed to the log in interface.
3. Input “User type” and “Password” in the log-in interface. Select the
display port (the default is full screen).
4-32
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Select display region
Once the connection is set up, click the button
to select the size of
the projection region: FullScreen, FixedSize, or Alterable.
FullScreen: The default capture mode turns to Full screen when the
program is launched. At that time, if screen capture starts, the image of the
whole screen is transferred to a remote network display.
y
y
y
FixedSize: FixedSize mode allows the users to place a frame on the
desktop. Only the image enclosed inside the frame is transferred to remote
network display.
Alterable: In Alterable mode the only region captured is the one enclosed
by the frame. The region can be enlarged or downsized by dragging the
eight small black squares scattered on eight edges of the frame.
E Series User Manual
4-33
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Configure Christie Presenter
Click the button
to configure Christie Presenter for Basic Setting
and Advanced Setting.
Basic Setting: Select language, change the region size of fixed size
capture mode, and select if notification message popup is allowed.
y
y
Advanced Setting: Select the quality of JPEG image, YUV sample format
and network port setting. (The "Fixed" port is Port 5900)
4-34
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Manage all connected network displays
Click the button
to control all the users and all the projectors
connector to the same projector.
Icon
Description
Administrator log in.
Normal user log in.
Device is connected.
Device is not connected.
The icon shows the current status and
display position of the local screen on the
network display. Click on the icon to change
the display position. A dialog box will appear.
Click this unlock icon to change the
password. (Password change to target
network display. Only an Administrator user
can change the password.)
No response is expected when this icon is
clicked. If the user is logged in as "Admin",
the key icon can be seen and the Presenter
password can be changed. If the user is
logged in as "Normal", the lock icon can be
seen and the Presenter password can't be
changed.
Disconnect from target network display.
Link for connecting to a target network
display via a webpage.
E Series User Manual
4-35
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.11 Card Reader Operation
There are four operation modes in the Card Reader application:
-
-
-
-
USB Flash Devices Detection Screen
Thumbnail Display Mode
Images Display Mode
Images Slide Show Mode
4.11.1 USB Flash Device Detection Screen:
In this mode, the Card Reader application detects any USB flash devices
hot-plug events and displays the flash device icon. When the flash device
is removed from USB, the icon disappears. It is suggested that USB flash
devices should be removed only when the Card Reader is changed to the
USB Flash Devices Detection Screen state.
4.11.2 Thumbnail Display Mode:
Press the Enter key to enter the Thumbnail Display Mode. Different photos
in different folders can be chosen. Press the Menu key to bring up the
Card Reader operation UI.
4-36
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
The user interface is designed to operate the card reader application with
a few keys (Enter/Left/Right/Up/Down).
The following buttons are supported in the user interface:
Previous: Move the selected item left. (Go to previous page when this is
the leftmost item)
y
y
Next: Move the selected item right. (Go to next page when this is the
rightmost item.)
Display: Display the selected image or display the selected folder.
Thumbnail: Enter the Thumbnail Display Mode.
SlideShow: Enter the Slide Show Mode.
y
y
y
y
y
y
y
y
NameOrder: Sort files/folders in name order.
ExtendOrder: Sort files/folders in extended order.
SizeOrder: Sort files/folders in size order.
TimeOrder: Sort files/folders in time order.
EXIF ON/OFF: Enable/Disable auto image rotate accordingly to EXIF
information.
FileName ON/OFF: Enable/Disable filename display in Thumbnail Display
y
Mode.
4.11.3 Image Display Mode:
Press the ENTER key in the Thumbnail Display Mode to enter the Image
Display Mode. Press the SlideShow key to enter the Slide Show Mode.
The Left/Right key is used to display the last/next image in the Image
Display Mode. In the Image Display Mode, press the ENTER key to quit
from the Image Display Mode and enter the Thumbnail Display Mode.
In the Slide Show Mode, press the ENTER key to enter the Image Display
Mode.
The alternative way to display image in the Image Display Mode or Slide
Show Mode is using the operation UI.
The following operations are supported in the operation UI.
Display: Enter the Image Display Mode.
y
E Series User Manual
4-37
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
Thumbnail: Enter the Thumbnail Display Mode.
y
y
y
y
y
y
y
SlideShow: Enter the Slide Show Mode.
Actual Size: Display in actual size of the image.
Best Fit: Display the image in best fit to the screen.
EXIFDisp OFF/On: Enable/Disable EXIF information display.
+90deg: Rotate 90 degree.
-90deg: Rotate -90 degree.
4.11.4 Image Slide Show Mode:
The following operations are supported in the Slide Show Mode operation
UI.
Stop: Stop Slide Show Mode.
y
y
y
y
y
Next: Display next image.
Previous: Display previous image.
Delay 3/4/5: Slide Show delay in seconds.
Slide Effect: Following modes are supported.
-
-
-
-
-
-
-
o Slide Right
o Blocks
o RightDown
o XLines
o Slide Up
o Ylines
o Repeat ON/OFF: Enable/Disable Slide Show Repeat Mode.
4-38
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
When the image cannot be displayed due to memory limitation or cannot
support image format, the specific image is displayed on the center of the
screen.
E Series User Manual
4-39
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4.12 Install the Lamp
The projector automatically detects the lamp life. When the lamp life is
nearing the end of use, you will receive a warning message. When you see
this message, please change the lamp as soon as possible. Make sure the
projector has been cooled down for at least 30 minutes before changing the
lamp.
1. Note the number of the lamp that needs to be replaced on the “Current Lamp” menu.
2. Turn off the lamps: Turn the projector OFF and disconnect the power cord.
3. Allow the projector to cool down for at least 30 minutes.
4. Open the lamp door: Unscrew the two screws on the lamp door.
5. Open the lamp door located on the top-rear of the projector.
6. Remove the lamp: Loosen the two captive screws securing the lamp.
7. Lift up the lamp by grasping handle and remove the lamp module slowly and carefully.
8. Install the new lamp: Replace the lamp with a new one and tighten two screws. Make
sure the lamp is set properly and secure.
9. Close the lamp door: Put the Lamp Door back on and tighten two screws.
10. Reset the projector: Turn the projector ON and use “Reset Lamp Hours” after the lamp
module is replaced.
11. Recommend calibrating light sensor if using Constant Intensity for lamp mode.
4-40
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Troubleshooting
5.
TROUBLESHOOTING
If you are unable to resolve an issue using the information provided in this
section, contact your reseller or service center.
Problem
Solution
No image appears
on-screen
-
Make sure all the cables and power connections are
correctly and securely connected See “Installation”.
y
y
-
-
Check if the lamp is securely installed.
Make sure you have removed the lens cap and the
projector is switched ON.
Partial, scrolling
or incorrectly
displayed image
-
-
Press “AUTO” on control panel or on remote control.
If you are using a PC (for Windows 95, 98, 2000, XP,
Windows 7):
“
” > “
”
Click the My Computer
Control Panel and then
1.
“
”
double - click Display .
“
”
Select the Settings tab.
2.
3.
Verify that your display resolution setting is lower
than or equal to WUXGA (1920 × 1200).
“
”
Click on the Advanced Properties button. If the
projector is still not projecting the whole image,
change the monitor display:
4.
4.1 Verify the resolution setting is lower than or equal
to WUXGA (1920 × 1200).
“
”
“
”
4.2 Select the Change button under the Monitor
tab.
“
”
“
4.3 Click on Show all devices . Next, select Standard
”
monitor types under the SP box; choose the
“
”
resolution mode you need under the Models
box.
4.4 Verify that the resolution setting of the monitor
display is lower than or equal to WUXGA (1920 ×
1200).
E Series User Manual
5-1
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Troubleshooting
Problem
Solution
Partial, scrolling
or incorrectly
displayed image
-
If you are using a Notebook:
y
Adjust resolution of the computer.
1.
2.
Press the keys listed below for your notebook
manufacturer to send signal out from notebook to
projector. Example: [Fn]+[F4]
Notebook Brand
Function Keys
Acer
[Fn]+[F5]
[Fn]+[F8]
[Fn]+[F8]
[Fn]+[F4]
[Fn]+[F7]
[Fn]+[F4]
[Fn]+[F3]
[Fn]+[F5]
Asus
Dell
Gateway
IBM/Lenovo
HP/Compaq
NEC
Toshiba
System Preference Display
Arrangement Mirror display
Mac Apple
-
-
If you experience difficulty changing resolutions or your
monitor freezes, restart all equipment including the
projector.
The screen of
the Notebook
or PowerBook
computer is not
displaying your
presentation
If you are using a Notebook PC
y
Some Notebook PCs may deactivate their own screens
when a second display device is in use. Each of them has
a different method of reactivation. Please refer to your
computer manual for detailed information.
Image is unstable
or flickering
-
-
Use “Pixel Track” and “Pixel Phase” to correct it.
y
y
Change the monitor color setting on your computer.
Image has vertical
flickering bar
-
-
Use “Auto Image” to make an adjustment.
Check and reconfigure the display mode of your graphic
card to make it compatible with the projector.
5-2
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Troubleshooting
Solution
Problem
Image is out of
focus
-
-
-
Make sure both lens caps (front and back) are removed.
y
y
Adjust lens focus to fit.
Make sure the projection screen is between the required
distance.
The image is
stretched when
displaying 16:9
DVD title
-
When you play anamorphic DVD or 16:9 DVD, the
projector will show the best image when the projector
display mode is set to 16:9 in the OSD.
-
-
If you play 4:3 format DVD titles, please change the format
to 4:3 in the projector OSD.
If the image is still stretched, you will also need to adjust
the aspect ratio by setting the display format as 16:9 (wide)
aspect ratio type on your DVD player.
Image is too small
or too large
-
-
Adjust lens zoom to fit.
y
y
If it does not fill the screen properly, verify that the correct
lens is in use or change the position of the projector.
Lamp burns out or
makes a popping
sound
-
If the lamp burns out, try power cycling the projector. If
the lamp doesn't fire or if you hear it make a loud pop, the
projector will not turn on until the lamp module has been
replaced.
E Series User Manual
5-3
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Specifications
6.
SPECIFICATIONS
6.1
Inputs
Signal
Type
Frame Rate
(Hz)
Display-
Compo-
nent
Resolution
640x480
HDMI 1
HDMI 2
VGA
●
BNC
●
S- video
CVBS
Port
60
75
85
60
75
85
60
75
85
60
50
60
60
75
85
60
60
60
60
50
60
50
50
60
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
640x480
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
640x480
●
●
800x600
●
●
800x600
●
●
800x600
●
●
1024x768
1024x768
1024x768
1280x768
1280x800
1280x800
1280x1024
1280x1024
1280x1024
1400x1050
1600x1200
1680x1050
1920x1200RB*
1920x1200RB*
●
●
●
●
●
●
●
●
PC
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
NTSC
NTSC
PAL
●
●
●
●
●
●
●
●
(M, 4.43)
PAL (B,G,H,I)
PAL (N)
PAL (M)
NOTE:
"RB" means "reduced blanking".
™
E Series User Manual
6-1
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Signal
Type
Frame Rate
(Hz)
Display-
Port
Compo-
nent
Resolution
SECAM (M)
480p
HDMI 1
HDMI 2
VGA
BNC
S- video
CVBS
SECAM
50
60
50
60
50
60
24
25
30
50
60
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
EDTV
576p
1080i
720p
720p
1080p
1080p
1080p
1080p
1080p
HDTV
6.2
PIP/PBP Compatibility
Main
Display-
Port
Compo-
nent
Com-
posite
USB type
B (mini)
USB
type A
HDMI 1 HDMI 2
VGA
BNC
S-video
RJ45
PIP/PBP
HDMI 1
●
-
-
●
-
●
●
●
●
●
HDMI 2
DisplayPort
VGA
●
●
-
●
-
●
-
-
●
●
-
●
●
-
●
●
-
●
●
-
●
●
-
●
●
-
●
●
-
-
-
-
-
BNC
●
-
●
-
●
-
●
-
Component
S-video
Composite
RJ45
●
-
●
-
●
-
●
-
●
-
●
-
●
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
-
-
-
-
-
-
-
-
-
-
-
-
-
USB type B
(mini)
-
-
-
-
-
-
-
USB type A
-
-
-
-
-
-
-
● : PIP/PBP combinations are enabled
- : PIP/PBP combinations are disabled
6-2
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Specifications
6.3
Key Features
”
”
HD 0.65 1920 × 1080 resolution or WUXGA 0.67 1920 × 1200 resolution
y
Projection lens compatibility:
y
-
-
-
Horizontal offset ranges: +/-20%
Vertical offset ranges: +120%/-40% (WUXGA) and +134%/-40% (HD)
Exception: 0.8:1 lens must be used on axis.
NOTE:
Measurements are based on industry standards where offset is calculated as a ratio of the number of pixels shifted
up/down to half the image size.
™
Dynamic aperture enabled (full white to full dark contrast ratio): 5000:1
(Nominal)
y
y
Dual Processor Warp Module for edge blending and geometric correction.
(Optional)
Wireless desktop display using wireless dongle (optional)
y
y
y
SNMP traps and e-mail notifications
Dual mercury lamp illumination with 330W (DWU/DHD675-E) & 350W
(DWU/DHD775-E)
10-bit image processor electronics with modular design
y
y
All video formats can be resized to full screen either horizontally or
vertically while maintaining aspect ratio
The projector can be operated using any of the following:
y
-
The built-in keypad, an infrared (IR) remote control, a wired remote
control, a PC/device using serial communications (Ethernet or RS232)
-
A Web page via Ethernet or from a PC/device via a wireless USB
dongle. (Optional)
Weight:
y
y
-
-
Maximum product weight (with lens removed): 19.5kg (43lb.)
Maximum shipping weight (includes packaging): 28kg (62lb.)
Built-In keypad
E Series User Manual
6-3
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4
List of Components
This projector comes with all the items shown below. Check to make sure your
package is complete. Contact your dealer if anything is missing.
IR remote control (133-114117-01)
Power cord x 4
y
y
-
-
-
-
UK/Korea/Russia
North America
Europe
Japan
DVI to HDMI dongle
y
y
User manual (CD)
NOTE:
Due to the difference in applications for each country, some regions may have different accessories.
™
6.5
Optional Accessories
Ceiling mount (optional accessory) (133-106108-XX)
Ceiling mount extension rod (104-101001-XX)
Fixed Lens (optional accessory):
y
y
y
-
Lens 0.8:1 Fixed Short (Zero offset) (133-100102-XX)
Zoom Lenses x 4 (optional accessory):
y
-
-
-
-
Lens 1.2-1.5:1 Fixed Short (133-101103-XX)
Lens 1.5-2.0:1 Zoom (133-102104-XX)
Lens 2.0-4.0:1 Zoom (133-103105-XX)
Lens 4.0-7.0:1 Long Zoom (133-104106-XX)
1DWUSB-BGN / Wireless dongle (optional accessory) (133-113106-XX)
Dual Processor Warp Module (optional accessory) (133-111104-XX)
Adapter Plate Stacker (optional accessory)(133-107109-02)
Stacking Frame (optional accessory)(118-100107-01)
y
y
y
y
y
E Series Color Wheel (Color) (optional accessory)(003-003411-01)
6-4
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Specifications
6.6
REGULATORY
Safety
y
-
-
-
-
CAN/CSA C22.2 No. 60950-1
UL 60950-1
IEC 60950-1
EN60950
Electro-Magnetic Compatibility
Emissions
y
-
FCC CFR47, Part 15, Subpart B/ICES-003/ANSI C63.4, Class A –
Unintentional Radiators
-
AS/NZS CISPR 22/EN55022 Class A - Information Technology
Equipment
-
-
EN 61000-3-2
EN 61000-3-3
Immunity
-
-
-
-
-
-
-
-
EN55024 EMC Requirements - Information Technology Equipment
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4,
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
Environmental
y
-
-
The product conforms to:
EU Directive (2002/95/EC) on the restriction of the use of certain
hazardous substances (RoHS) in electrical and electronic equipment
and the applicable official amendment(s).
-
EU Regulation (EC) No. 1907/2006 on the registration, evaluation,
authorization and restriction of chemicals (REACH) and the applicable
official amendment(s).
-
-
EU Directive (2002/96/EC) on waste and electrical and electronic
equipment (WEEE) and the applicable official amendment(s).
China Ministry of Information Industry Order No.39 (02/2006) on the
control of pollution caused by electronic information products, the
hazardous substances concentration limits (SJ/T11363-2006), and the
applicable product marking requirement (SJ/T11364-2006).
E Series User Manual
6-5
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Marking
y
-
This product shall conform to all relevant Canadian, US, and European
directives, standards, safety, health and environmental concerns and
bear the following markings at product launch:
UL
`
`
`
`
CE
RoHS
WEEE
-
-
Future product markings to include International Certifications: CCC,
KC, PSE, c-tick, Gost-R, South Africa
International packaging recycling mark requirements:
EU Directive (2002/96/EC) on waste and electrical and electronic
equipment (WEEE);
`
EU Directive (94/62/EC) on packaging and packaging waste;
`
`
China packaging recycling mark standard (GB18455-2001).
6-6
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Specifications
6.7
Declaration of Conformity for EU Countries
EMC Directive 2004/108/EC (including amendments)
y
y
y
Low Voltage Directive 2006/95/EC
Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
6.8
Federal Communications Commission (FCC) Warning
WARNING
A shielded-type power cord is required in order to meet FCC emission
limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used.
y
y
Use only shielded signal cables to connect I/O devices to this equipment.
E Series User Manual
6-7
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
6.9
MENU TREE
Level 1 Level 2
Level 3(Or List)
Level 4(Or List)
Level 5(Or List)
Level 6(Or List)
Default
Auto
Native
4:3
Size Presets
Letterbox
Full Size
Full Width
Full Height
Off
Auto
Overscan
Zoom
By source set
Crop
Pixel Track
0 - 100
50
Pixel Phase
Horz Position
Vert Position
0 - 100
0 - 100
0 - 100
50
50
50
Digital Horz Zoom
Digital Vert Zoom
Digital Horz Shift
Digital Vert Shift
50%~400%
50%~400%
0 - 100
100
100
50
50
0 - 100
Off (see Note 1)
Off
Horz Keystone
Vert Keystone
Horz Pincushion
Vert Pincushion
Pincushion/Barrel
0 - 100 (0-20 for GEO model)
0 - 100 (0-20 for GEO model)
0 - 100
0 - 100
0-20
Top Left Horz adjust.
Top Left Vert adjust.
Top Right Horz adjust.
Top Right Vert adjust.
Bottom Left Horz adjust.
Bottom Left Vert adjust.
Bottom Right Horz adjust. 0-160
Bottom Right Vert adjust. 0-80
Top Arc
50 (10 for GEO model)
50 (10 for GEO model)
50
50
10
0
0
0
0
0
0
0
0-160
0-80
0-160
0-80
0-160
0-80
Basic
Size & Position
4-Corner
Curve
0
0-400
0-400
0-400
0-400
0-160
0-80
0-160
0-80
0-160
0-80
200
200
200
200
0
0
0
0
0
0
0
0
8
0
0
0
0
Bottom Arc
Left Arc
Right Arc
Geometry Correction
Top Left Horz adjust.
Top Left Vert adjust.
Top Right Horz adjust.
Top Right Vert adjust.
Bottom Left Horz adjust.
Bottom Left Vert adjust.
Bottom Right Horz adjust. 0-160
Bottom Right Vert adjust. 0-80
0-16
Top Left Horz adjust.
Top Left Vert adjust.
Top Right Horz adjust.
Top Right Vert adjust.
Bottom Left Horz adjust.
Bottom Left Vert adjust.
Curve
4-Corner
Rotation
4-Corner
0-160
0-80
0-160
0-80
0-160
0-80
Rotate
0
0
Bottom Right Horz adjust. 0-160
Bottom Right Vert adjust. 0-80
0
0
Auto Image
Brightness
Contrast
command
0 - 100
0 - 100
50
By source set
RGB
REC709
Color Space
REC601
Auto
RGB Video
Auto
Maximum
High
Detail
Normal
By source set
Low
Minimum
Color
Tint
Noise Reduction
Flesh Tone Correction
Video Black Level
Detect Film
0 - 100
0 - 100
0 - 100
0 - 100
50
50
0
0
Video Options
Off/On
Off
cc1
Off
Off
Image settings
Closed captions
cc2
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Sync Threshold
Reset RGB Gain/Offset
Presentation
Video
0 - 100
0 - 100
0 - 100
0 - 100
0 - 100
0 - 100
0 - 100
command
50
50
50
50
50
50
50
Input Levels
Bright
Picture Settings
Whiteboard
Blackboard
Beige Wall
User
By source set
Save to User
DynamicBlack
command
Off / On
Off
6-8
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Specifications
Level 1
Level 2
Level 3(Or List)
Off / On
Level 4(Or List)
Level 5(Or List)
Level 6(Or List)
Default
Off
Image Freeze
Video
Film
Bright
CRT
Gamma
By source set
Normal Look
Bright Look
0 - 100
Warmest
Warm
Cool
BrilliantColorTM
White Peaking
Bright
By source set
Image settings
Color Temperature
By source set
Advanced Image Settings
Bright
Off
Edge Enhancement
Color Wheel Speed
Color Enhancement
Normal
Maximum
2X
3X
Off
Off
2X
CE 1
CE1
CE 2
Language
SPEC define
Focus
Zoom
English
command
command
command
Allow
Lens Shift
Lens settings
Lock all Lens Motors
Allow
Locked
Lens center calibration
Off/On/Auto
Off/On
Menu Horz Offset
Menu Vert Offset
Show Messages
Menu Transparency
command
Ceiling Mount
Rear Projection
Auto
Off
0
0
on
0
0 - 100
0 - 100
off/on
0 - 90
Factory Logo
Blue
Black
Menu Preferences
Splash Screen Setup
Factory Logo
White
PIN Protect
Change PIN
command
command
0.5 W mode
Communication mode
off/on
Standby Mode
AC Power On
Communication mode
off
Never
5 Mins
10 Mins
15 Mins
20 Mins
25 Mins
30 Mins
Off
Auto shutdown
Never
Power Management
2 Hrs
4 Hrs
6 Hrs
Sleep Timer
Off/On
Off
Off
High Altitude
DHCP
IP Address
Subnet Mask
Configuration
LAN
by set
Default Gateway
MAC Address
Enable
Start IP
End IP
Subnet Mask
Default Gateway
MAC Address
SSID
Password
Projector Name
Show Network Messages
Restart Network…
WLAN
by set
by set
Communications
Network
Network Factory Reset…
2400
4800
9600
14400
Serial Port Baud Rate
19200
115200
38400
57600
115200
1200
Serial Port Echo
Projector Address
Blending
Marker
Grid
Off/On
0 - 9
On/Off
On/Off
Off/White/Red/Green/Blue
Off/White/Red/Green/Blue
Top
Bottom
Off
0
Off
Off
Off
Off
0
0
0
0
Solid Color
0… ½ Output Height(Pixel)
0… ½ Output Height
0… ½ Output Width
0… ½ Output Width
0-2000
Image Blending
Overlap
Left
Right
Blending Area offset
non-Blending Area Offset
1000
1000
Bright Adj.
0-2000
E Series User Manual
6-9
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Level 1
Level 2
Image Blending
Level 3(Or List)
Drop Off Curve
Image Gamma
Level 4(Or List)
70-300
1.8/2.0/2.2/2.4/2.6
Enable
Level 5(Or List)
Level 6(Or List)
Default
100
2.2
On/Off
Off
Auto Test Pattern
On/Off
On
Intensity of Red
x of Red
y of Red
Intensity of Green
x of Green
y of Green
Intensity of Blue
x of Blue
100 - 10000
453
0.300 - 0.700
0.300 - 0.500
100 - 10000
0.300 - 0.400
0.400 - 0.700
100-10000
0.100 - 0.300
0.030 - 0.400
100-10000
0.633
0.356
2137
0.352
0.572
239
0.140
0.093
9219
0.331
0.380
Measured Data
y of Blue
Intensity of White
x of White
y of White
Reset to Default
Gain of Red
x of Red
0.200 - 0.400
0.200 - 0.400
Yes/No
Meter Adjustment
0.200 - 1.000
0.300 - 0.700
0.300 - 0.500
0.200 - 1.000
0.300 - 0.400
0.400 - 0.700
0.200 - 1.000
0.100 - 0.300
0.030 - 0.400
0.200 - 1.000
0.200 - 0.400
0.200 - 0.400
Yes/No
1.000
0.643
0.344
1.000
0.329
0.544
1.000
0.141
0.094
1.000
0.334
0.371
y of Red
Gain of Green
x of Green
y of Green
Gain of Blue
x of Blue
Color Matching
Target Data
y of Blue
Gain of White
x of White
y of White
Reset to Default
On/Off
On/Off
0 - 1000
0 - 1000
Enable
Off
On
1000
0
Auto Test Pattern
Red Part of Red
Green Part of Red
Blue Part of Red
Green Part of Green
Red Part of Green
Blue Part of Green
Blue Part of Blue
Red Part of Blue
Green Part of Blue
Red Part of White
Green Part of White
Blue Part of White
Reset to Default
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0
1000
0
0
1000
0
0
1000
1000
1000
Manual Adjustment
Configuration
0 - 1000
0 - 1000
Yes/No
Blank Screen
Aspect Ratio
Freeze Screen
Projector Info
Overscan
Hot-Key settings
Closed Captions
Model Name
Serial Number
Native Resolution
Firmware
Configuration
Boot Code
Standby Mode
Lens Lock Settings
Color wheel Index
command
Off
Projector Info
FactoryReset…
Grid
White
Black
Service
Checkerboard
Color Bars
Red
Test pattern
Green
Blue
Yellow
Magenta
Cyan
Color wheel Index (2x)
Color wheel Index (3x)
TBD
TBD
Show log
Clear log
Error log
Mode Adjustment
Constant Power/Constant
Intensity
Lamp mode
Constant Power
280 - 330
(280 - 350 for SONICIII)
330
Constant Power
(350 for SONICIII)
Constant Intensity
(see Note 5)
0 - 10
7
Lamp 1
Lamp 2
Both
Lamp
Current Lamp
Both
Off
Lamp 1
Lamp 2
Auto
Eco Mode
Off
Lamp Auto Switch
On Failure Only
On Failure Only
6-10
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Specifications
Level 1
Lamp
Level 2
Lamp Auto Switch
Level 3(Or List)
At Power-Up
After (N) Hours
5 - 3000
Lamp 1 Hours
Lamp 2 Hours
Total Hours All Lamps
Lamp 1 Reset
Lamp 2 Reset
xxxxx
Level 4(Or List)
Level 5(Or List)
Level 6(Or List)
Default
On Failure Only
Lamp Auto Switch Time (Hours)
100
Lamp Info
Lamp Life Setting
Reset Lamp Hours…
Light Sensor
1500 hrs
command
Light Sensor Calibration
Calibrated?
command
(display Yes/No)
(see Note 6).
Model Name
Serial Number
Native Resolution
Firmware
˩̋̋ʿʳ˔̌̌ʿʳ˕̍̍
Main Input
Main Signal Format
Main Pixel Clock
Main Sync Type
Main Horz Refresh
Main Vert Refresh
PIP/PBP Input
PIP/PBP Signal Format
PIP/PBP Pixel Clock
PIP/PBP Sync Type
PIP/PBP Horz Refresh
PIP/PBP Vert Refresh
Lamp Power Settings
Current Lamp
Status
Lamp 1 Hours
Lamp 2 Hours
Standby Mode
Lens Lock Settings
IP Address
DHCP
System Temperature
Main Input
PIP/POP Input
SPEC define
SPEC define
OFF
PIP/POP Enable
OFF
ON
Swap
Size
(Small/Medium/Large)
(PBP, Main Left /PBP, Main
Top / PBP, Main Right / PBP,
Main Bottom / PIP-Bottom
Right / PIP-Bottom Left /
PIP-Top Left / PIP-Top Right)
Normal
Main Layout
Timing Detection Mode
Wide
Wide
Active Source
Signal Format
Aspect Ratio
Resolution
Vert Refresh
Horz Refresh
Pixel Clock
Sync Type
Color Space
Source Info
Input
Switching &
PIP
PIP/POP
<PIP/POP source lines>
ON
(When PIP/POP active)
(When PIP/POP active)
Enable source Hot-Key
Source Hot-Key
ON
OFF
VGA
BNC
HDMI 1
HDMI 2
Display Port
Component
S-Video
Key number 1
Key number 2
Key number 3
Key number 4
Key number 5
Key number 6
Key number 7
Key number 8
Key number 9
Key number 0
Off
Composite
Christie Presenter
Card Reader
Mini USB
Change Sources
List all Sources
Auto Source
Input key
Auto Source
English
Language
SPEC define
Off
Grid
White
Test pattern
Black
Checkerboard
Color Bars
E Series User Manual
6-11
020-000515-01 Rev. 2 (03-2013)
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
United Kingdom
ph: +44 118 977 8000
Eastern Europe
ph: +36 (0) 1 47 48 100
Singapore
ph: +65 6877-8737
Japan
ph: 81-3-3599-7481
France
ph: +33 (0) 1 41 21 00 36
Middle East
ph: +971 (0) 4 299 7575
Beijing
ph: +86 10 6561 0240
South Korea
ph: +82 2 702 1601
Germany
ph: +49 2161 664540
Spain
ph: + 34 91 633 9990
Shanghai
ph: +86 21 6278 7708
P/N 36.8HP05G001-B
Download from Www.Somanuals.com. All Manuals Search And Download.
|