GAS POWERED
POLESAW/PRUNER
1 HP
Model 95283
ASSEMBLY AND OPERATING INSTRUCTIONS
Do to continuing improvements, actual product may differ slightly from the product described herein.
CAUTION!
Your Warranty Is Voided If:
You do not operate the Polesaw/Pruner with the proper 50:1 fuel mix in its fuel tank.
Never run the Engine with an improper fuel mix, low or no fuel mix.
Running the Engine with an improper fuel mix, low or no fuel mix, will permanently damage the unit.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
Copyright 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor FreightTools.
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
sparks which may ignite the dust or fumes.
3.
1.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Provide barriers or shields as
needed.
PERSONAL SAFETY
Stay alert. Watch what you are doing, and use common sense when
operating a power tool. Do not use a power tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
2.
3.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure the Power Switch is in its “OFF”
position before moving the Polesaw/Pruner and before performing any
service, maintenance, or cleaning procedures on the unit.
4.
5.
Remove adjusting keys or wrenches before turning the Polesaw/Pruner on.
A wrench or a key that is left attached to a rotating part of the machine may
result in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected
situations.
TOOL USE AND CARE
1.
2.
Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the Polesaw/Pruner if the Power Switch does not turn it on or
off. Any tool that cannot be controlled with its power switch is dangerous and
must be replaced.
3.
4.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Maintain tools with care. Properly maintained tools are less likely to malfunction
and are easier to control. Do not use a damaged tool. Tag damaged tools
“Do not use” until repaired.
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
6.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have
the tool serviced before using. Many accidents are caused by poorly
maintained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SERVICE
1.
2.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning”section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES AND PRECAUTIONS
1.
IMPORTANT! Your Warranty is voided if:
You do not operate the Polesaw/Pruner with the proper 50:1 fuel mix in its
fuel tank. Never run the Engine with an improper fuel mix, low or no fuel mix.
Running the Engine with an improper fuel mix, low or no fuel mix, will
permanently damage the unit.
2.
3.
Maintain labels and nameplates on the Polesaw/Pruner. These carry
important information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
WARNING! Always wear safety equipment. When operating
the Polesaw/Pruner, always wear ANSI approved safety impact
eye goggles, hearing protection, heavy duty work gloves, sturdy
work boots, and head protection.
4.
5.
Never leave the Polesaw/Pruner unattended when it is running. Turn off the
Engine before leaving.
Never allow children in the work area with the danger of falling debris and a
power tool in operation.
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
7.
8.
Always plan carefully where a tree limb will fall to avoid damage to property
and/or personal injury.
Never stand directly beneath the limb you are cutting. Always stand well off
to the side.
Do not use the Polesaw/Pruner to cut anything except tree limbs and
brush.
9.
Always maintain a firm grip on the Polesaw/Pruner with both hands.
10.
Branch trimming is a dangerous activity. The use of this Polesaw/Pruner
requires that you be in good physical condition, and with good balance and
coordination. If you are in doubt about the safety issues involved, have a
qualified, certified, arborist/tree surgeon do the work for you.
11.
Always keep hand, fingers, and body a safe distance away from the moving
Chain.
12.
13.
Do not use the Polesaw/Pruner if the Chain is dull.
Make sure the wood being cut does not contain foreign materials such as
nails, spikes, etc.
14.
15.
WARNING! Ladders are inherently dangerous. NEVER use a ladder
when using the Polesaw/Pruner.
WARNING! Stay clear of engine components which will be hot during
and after operation.
KICKBACK PRECAUTIONS
1.
Kickback is a dangerous reaction that can lead to serious injury. Kickback
may occur when the moving Chain contacts an object at the upper portion of the
tip of the Guide Bar or when the wood closes in and pinches the Saw Chain in
the cut.
Contact at the upper portion of the tip of the Guide Bar can cause the Chain to
dig into the wood and stop the Chain for an instant. The result is a quick, reverse
reaction which kicks the Guide Bar up and back toward the operator. If the
Chain is pinched along the top of the Guide Bar, the Guide Bar can be driven
rapidly back toward the operator. Either of these reactions can cause loss of
Polesaw/Pruner control which can result in serious injury.
Do not rely only upon the safety devices built into the Polesaw/Pruner. As an
operator, you should take several steps to keep the cutting job free from accident
or injury:
A. Make sure the area in which you are cutting is free from obstructions. Do
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
not allow the nose of the Guide Bar to contact a log, branch, fence, or any
other obstruction while you are operating the tool.
B. Always cut with the Engine running at full speed. Fully squeeze the Throttle
and maintain a steady cutting speed.
C. Always keep the Chain clean and sharp.
D. Keep all guards and safety devices in proper working order and properly
adjusted.
E. Never use the Polesaw/Pruner on a ladder or unstable support.
F. Before starting the Engine, make sure the Chain is not contacting any object.
G. Shut off the Engine, and make sure the Chain has stopped before setting the
tool down.
ELECTRICAL PRECAUTIONS
1.
2.
To protect yourself from electrocution, do not operate the Polesaw/
Pruner within 50 feet of any overhead electrical lines.
NEVER use the Polesaw/Pruner in damp or wet conditions.
CARBON MONIXIDE PRECAUTIONS
1.
WARNING! This Polesaw/Pruner is designed for outdoor use only. Do
not operate the Polesaw/Pruner in a closed area or in a poorly ventilated area.
When running, the Engine of this product produces carbon monoxide, a
colorless, odorless, toxic gas that, when inhaled, can cause serious
personal injury or death.
FIRE AND EXPLOSION PRECAUTIONS
1.
Gasoline fuel and fumes are flammable, and potentially explosive.
Use proper fuel storage and handling procedures. Always have multiple
ABC class fire extinguishers nearby.
2.
3.
Keep the Polesaw/Pruner and surrounding areas clean at all times.
When spills of fuel or oil occur, they must be cleaned up immediately.
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Dispose of fluids and cleaning materials as per any local, state, or federal codes
and regulations. Store oil rags in a covered metal container.
4.
5.
Never store fuel or other flammable materials near the Polesaw/Pruner.
Do not smoke, or allow sparks, flames, or other sources of ignition around
the Polesaw/Pruner.
6.
Keep grounded conductive objects, such as tools, away from exposed, live
electrical parts and connections to avoid sparking or arcing. These events
could ignite fumes or vapors.
7.
8.
Do not refill the FuelTank while the Engine is running or while the Engine is
still hot. Do not operate the Polesaw/Pruner with known leaks in the fuel system.
Use only Engine manufacturer recommended fuel and oil.
MECHANICAL PRECAUTIONS
1.
Prior to performing service, maintenance, or cleaning procedures, always
make sure the Power Switch is in its “OFF” position. Allow the Engine
to completely cool. Then, remove the spark plug from the Engine.
2.
3.
Do not alter or adjust any part of the Polesaw/Pruner or Engine that is
assembled and supplied by the manufacturer.
Always follow and complete scheduled Polesaw/Pruner and Engine
maintenance.
CHEMICAL PRECAUTIONS
1.
2.
Avoid contact with hot fuel, oil, exhaust fumes, and solid surfaces.
Avoid body contact with fuels, oils, and lubricants used in the Polesaw/
Pruner and Engine. If swallowed, seek medical treatment immediately. Do not
induce vomiting if fuel is swallowed. For skin contact, immediately wash with
soap and water. For eye contact, immediately flush eyes with clean water.
NOISE PRECAUTIONS
1.
Prolonged exposure to high noise levels is hazardous to hearing.
Always wear ANSI approved hearing protection when operating or working
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
around the Polesaw/Pruner when it is running.
MISC. PRECAUTIONS
1.
2.
DANGER! We recommend that people with pacemakers not use this tool.
This tool produces strong electromagnetic fields that can cause interference to or
failure of the pacemaker. People with pacemakers should consult their
physician(s) for advice.
WARNING! The warnings and precautions discussed in this manual cannot
cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built
into this product, but must be supplied by the operator.
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts Lists on pages 18
and 20 are included. If any parts are missing or broken, please call Harbor Freight Tools
at the number shown on the cover of this manual as soon as possible.
ASSEMBLY INSTRUCTIONS
1.
2.
Insert the Gear Box (61) onto the upper section of the Top Pipe Support (33).
Then secure the Gear Box to the Top Pipe Support using one short Screw (59),
one Washer (60), one long Screw (58), one Spring Washer (57), and one Washer
(56). (See Figure A.)
Insert the lower section of the Top Pipe Support (33) into the Connector (22).
Then secure the Top Pipe Support to the Connector by firmly tightening the Wing
Nut (31). (See Figure A.)
GEAR BOX (61)
SCREW (59), WASHER (60)
SCREW (58), SPRING WASHER (57), WASHER (56)
TOP PIPE SUPPORT (33)
WING NUT (31)
FIGURE A
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT FEATURES
1.
2.
3.
Top Pipe Support (33): Prior to using the Polesaw/Pruner, always check to
make sure all other connecting parts are firmly secured to the Top Pipe Support.
(See Figure B.)
Guard Bar Cover (78): Make sure to remove the Guard Bar Cover prior to
operating the Polesaw/Pruner. When not in use, keep the Guard Bar and Chain
protected with the Guard Bar Cover. (See Figure B.)
Chain Saw Cover (77): The Chain Saw Cover allows access when replacing
the Guard Bar (73) and/or Chain (74). The Chain Saw Cover is held in place with
one Nut (75). Prior to starting the Polesaw/Pruner, always check to make sure
the Nut is tightened securely. (See Figure B.)
4.
Wing Nut (31): Prior to each use of the Polesaw/Pruner, make sure the Wing
Nut is firmly tightened in order to properly secure the Top Pipe Support (33) to
the unit. (See Figure B.)
33
2
31
77
10
1
8
78
14
74
39
73
87A
50
48A
55A
69
42A
4A
FIGURE B
78A
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Bottom Pipe Support (2): Always hold the Polesaw/Pruner firmly with both
hands. Keep your left hand on the front portion of the Bottom Pipe Support and
your right hand on the rear portion of the Bottom Pipe Support, so that your
body is to the left of the chain line. Never use a left-handed (cross-handed) grip
or any stance which would place your body or arm across the chain line.
(See Figure B.)
6.
7.
Power Switch (10)/Throttle Lever (8): The Power Switch is a simple “ON”/
OFF” rocker type switch. Squeezing the Throttle Lever controls the speed at
which the tool runs. (See Figure B.)
Engine Assembly: The Polesaw/Pruner features a 1 Horsepower, 26cc,
single cylinder, 2-stroke Engine. Do not attempt to start or run the Engine with
out adding the proper 50:1 ratio of fuel and 2-cycle oil in the Engine’s Fuel Tank
(78A). When in use, use caution to avoid touching the hot parts of the Engine.
(See Figure B, and refer to the “Pre-Start Instructions” section of this
manual.)
8.
9.
Shoulder Harness (14): Always wear the Shoulder Harness for increased
safety and to support the Polesaw/Pruner. (See Figure B.)
Primer (87A): The Engine (1), when cold, must be primed with fuel prior to
to starting the unit. To do so, simply press inward on the Primer three to four
times with your index finger. Then, proceed with starting the unit.
(See Figure B.)
10.
ChainTension Adjusting Screw (39): The Chain (74) is properly tensioned
when there is no slack on the underside of the Guard Bar (73). The Chain
should be snug, but should turn by hand without binding. To adjust the tension of
the Chain, turn off the Engine (1). Slightly loosen the Nut (75) on the Chain Saw
Cover (77). Remove all slack from the Chain by turning the Chain Tension
Adjusting Screw clockwise, making sure the Chain seats into the Bar Guard
groove during tensioning. Lift the tip of the Bar Guard up to check for sag.
Release the tip of the Bar Guard, and turn the Chain Tensioning Screw 1/2 turn
clockwise. Repeat this process until sag does not exist. Then, retighten the
Nut. NOTE: If the Chain is too tight, it will not rotate. Loosen the Nut slightly and
turn the Chain Tension Adjusting Screw 1/4 turn counterclockwise. Lift the tip of
the Bar Guard up to check for proper tension. Then retighten the Nut.
(See Figure B.)
11.
Saw Chain (74): To avoid possible injury, never touch or adjust the Chain while
the Engine (1) is running. The Chain is very sharp. Always wear heavy duty
work gloves when performing maintenance to the Chain. Adjust the Chain
tension only when the Chain is cold. Chain tensioning while warm may be too
tight upon cooling. IMPORTANT: The cutters on the top of the Guard Bar
should face toward the Guard Bar tip, in the direction of the chain rotation.
(See Figure B.)
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
12.
Guard Bar (73): Always place the Guard Bar Cover (78) on the Guard Bar
when transporting or storing the Polesaw/Pruner. The Guard Bar Cover fits
snugly onto the Guard Bar and must be attached carefully due to the sharp teeth
of the Saw Chain (74). Always wear heavy duty work gloves when installing the
Guard Bar Cover. (See Figure B.)
13.
14.
Oil Tank (69): Refer to the “Pre-Start Instructions” section in this manual for
full details. (See Figure B.)
Gear Box Grease Fitting (50): The Drive Gear (44) assembly should be filled
(through the Gear Box Grease Fitting) with clean, new, automotive axle grease
every three months or 50 hours of tool use. (See Figure B.)
15.
16.
17.
18.
Spark Plug (55A): The condition of the Spark Plug should be checked every six
months or 100 hours of tool use. If necessary, clean or replace the Spark Plug.
ALWAYS remove the Spark Plug prior to performing any inspection,
maintenance, or cleaning of the Polesaw/Pruner. (See Figure B.)
Choke Lever (48A): The Choke Lever must be set to its “START” position when
starting a cold Engine (1). Once started, move the Choke Lever to its “RUN”
position. When starting a warm Engine, make sure the Choke Lever is in its
“RUN” position. (See Figure B.)
Air Filter (42A): The Air Filter should be checked prior to each use of the
Polesaw/Pruner for excessive dirt and debris build-up. Thereafter, the Air Filter
should be cleaned or replaced every three months or 50 hours of tool use.
(See Figure B.)
Fuel Tank (78A): The Fuel Tank will hold up to 0.2 gallon of fuel. Always make
sure the Fuel Cap (74A) is securely replaced after filling the Fuel Tank. NEVER
attempt to fill the Fuel Tank when the Engine (1) is running or hot to the touch.
Refer to the “Pre-Start Instructions” section in this manual for full details on
filling the Fuel Tank with the proper unleaded fuel/2-cycle oil mixture.
(See Figure B.)
19.
Starter Handle (4A): Refer to the “To Start The Polesaw/Pruner” section in
this manual for full details. (See Figure B.)
PRE-START INSTRUCTIONS
To Fill The Chain Oil Tank:
1.
Prior to each use of the Polesaw/Pruner, the Chain Oil Tank (69) must be filled
with S.A.E. 30 weight oil (below 34o Fahrenheit) or S.A.E. 40 weight oil
(above 75o Fahrenheit). (See Figure B.)
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
Remove the Chain Oil Tank Cap (67) and carefully fill the Chain Oil Tank (69).
Then, replace the Chain Oil Tank Cap and tighten securely. (See Figure B.)
NOTE: Do not use dirty, used, or otherwise contaminated oil. Damage may
occur to the Oil Pump (47), Guard Bar (73), or Saw Chain (74). (See Figure B.)
To Fill The Fuel Tank:
1.
2.
IMPORTANT! Your warranty is voided if:
You do not operate the Polesaw/Pruner with the proper 50:1 fuel mix in its
Fuel Tank (78A). Never run the Engine (1) with an improper fuel mix, low or no
fuel mix. Running the Engine with an improper fuel mix, low or no fuel mix will
permanently damage the unit. (See Figure B.)
To obtain the proper 50:1 fuel mix, combine 50 parts unleaded gasoline with 1
part 2-cycle oil in a clean, approved container. Cover and shake to thoroughly
mix before each fueling. NOTE: Mix only enough fuel for a few days work. The
maximum storage time of mixed fuel is three months.
3.
4.
Once the proper fuel mix is obtained, remove the Fuel Cap (74A). Fill the Fuel
Tank (78A) approximately 3/4 full with the fuel mix (the Fuel Tank capacity is 0.2
gallon). Then, replace the Fuel Cap. (See Figure B.)
WARNING! NEVER attempt to fill the Fuel Tank (78A) when the Engine (1)
is running or hot to the touch.
OPERATING INSTRUCTIONS
To Start The Polesaw/Pruner:
1.
WARNING! Always wear safety equipment. When operating the Polesaw/
Pruner, always wear ANSI approved safety impact eye goggles, hearing
protection, heavy duty work gloves, sturdy work boots, and head protection.
2.
3.
Check to make sure the Power Switch (10) is in its “OFF” position.
(See Figure B.)
Remove the Guard Bar Cover (78) from the unit. Place the Polesaw/Pruner on a
flat, level, ground surface, making sure the Saw Chain (74) does not come in
contact with any objects on the ground. (See Figure B.)
4.
Set the Choke Lever (48A) to the appropriate position:
A. “START” if the Engine (1) is cold. (See Figure B.)
B. “RUN” if the Engine (1) is warm. (See Figure B.)
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
With your index finger, pressed firmly on the Primer (87A) three or four times.
(See Figure B.)
6.
7.
8.
Turn the Power Switch (10) to its “ON” position. (See Figure B.)
Squeeze the Throttle Lever (8). (See Figure B.)
Hold the Bottom Pipe Support (2) with your left hand, and place your right foot
on the rear section of the Engine (1). Firmly press the Polesaw/Pruner to the
ground, making sure the Saw Chain (74) does not come in contact with any
objects on the ground. (See Figure B.)
9.
Hold the Starter Handle (4A) securely, and slowly pull out the Starter Rope (7A)
for a short distance. Then, pull out the Starter Rope quickly. (See Figure B.)
10.
11.
If the Engine (1) does not start, press the Primer (87A) again and attempt to
start the Engine. (See Figure B.)
If the Engine (1) runs for a short while, but does not continue running, press the
Primer (87A) again. Move the Choke Lever (48A) to its “RUN” position and
restart the Engine. (See Figure B.)
12.
As soon as the Engine (1) is running, check to make sure the Choke Lever (48A)
is in its “RUN” position. Squeeze the Throttle Lever (8) briefly and let up. The
Throttle Lever will revert to its original position, causing the Engine to idle.
(See Figure B.)
13.
14.
NOTE: If the Engine (1) is new, or has been stored for a long period of time, pull
the Starter Handle (4A) several times to ensure sufficient fuel is delivered into
the fuel line and combustion chamber of the Engine. (See Figure B.)
WARNING! The Saw Chain (74) should never turn at idle. If necessary,
turn the Idle Screw of the Carburetor counterclockwise to reduce the idle RPM
and stop the Chain, or immediately discontinue using the Polesaw/Pruner and
contact a qualified service technician to make the adjustment.
To Stop The Polesaw/Pruner:
1.
Let up on the Throttle Lever (8). Then turn the Power Switch (10) to its “OFF”
position. (See Figure B.)
To Operate The Polesaw/Pruner:
1. Maintain a proper grip on the Polesaw/Pruner whenever the Engine (1) is
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
running. Hold the tool with both hands. Always keep your left hand on the
forward portion of the Bottom Pipe Support (2) and your right hand on the rear
portion of the Bottom Pipe Support, so that your body is to the left of the chain
line. Never use a left-handed (cross-handed) grip or any stance which would
place your body or arm across the chain line. (See Figure D.)
FIGURE D
2.
Accelerate the Engine (1) to full throttle just before entering the cut by squeezing
the Throttle Lever (8). To avoid the possiblity of kickback, keep the Engine (1) at
full throttle the entire time you are cutting. (See Figure B.)
3.
4.
DO NOT use a back and forth sawing type motion for cutting.
Allow the Saw Chain (74) to cut for you. Exert only light downward pressure. If
you attempt to force the cut, damage to the Guard Bar (73), Saw Chain (74), or
Engine (1) can result. (See Figure B.)
5.
6.
Release the Throttle Lever (8) as soon as the cut is completed, allowing the
Engine (1) to idle. NOTE: Running the Polesaw/Pruner at full throttle without a
cutting load can cause unnecessary wear or damage to the Guard Bar (73), Saw
Chain (74), or Engine (1). (See Figure B.)
IMPORTANT: After running the Polesaw/Pruner for an extended period of time,
allow the Engine (1) to idle for several minutes to dissipate the heat. This will
prevent some Engine parts (ignition system, piston rings, carburetor, etc.) from
being damaged by overheating. Then turn the Power Switch (10) to its “OFF”
position. (See Figure B.)
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Before storing the Polesaw/Pruner, make sure to install the Guard Bar Cover
(78) onto the Guard Bar (73). Drain all fuel out of the tool’s Fuel Tank (78A). If
this is not followed, old fuel in the Fuel Tank may clog the Carburetor and prevent
the tool from starting until cleaned out. Then store the tool in a clean, dry, safe
location out of reach of children and other unauthorized people. (See Figure B.)
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
WARNING! Always make sure the Engine’s Power Switch (10) is in its
“OFF” position and the Spark Plug (55A) is removed prior to performing any
service, maintenance, or cleaning of the Polesaw/Pruner. (See Figure B.)
Before each use: Inspect the general condition of the Polesaw/Pruner. Check
misalignment or binding of moving parts, cracked or broken parts, dull or
damaged Saw Chain (74) or Guard Bar (73), and any other condition that may
affect the safe operation of the tool. If abnormal noise or vibration occurs, have
the problem corrected before further use. Do not use damaged equipment.
3.
Saw Chain (74) maintenance: A dull, improperly sharpened, or damaged Saw
Chain can cause kickback, leading to possible personal injury. It is recommended
that only a qualified service technician attempt to sharpen or replace the Saw
Chain.
4.
5.
Spark Plug (55A) maintenance: The condition of the Spark Plug should be
checked every six months or 100 hours of tool use. If necessary, clean or replace
the Spark Plug.
Air Filter (42A) maintenance: The Air Filter should be checked prior to each
use of the Polesaw/Pruner for excessive dirt and debris build-up. Thereafter, the
Air Filter should be cleaned or replaced every three months or 50 hours of tool
use.
6.
7.
Drive Gear (44) maintenance: The Drive Gear assembly should be filled,
through the Gear Box Grease Fitting (50), with clean, new, automotive axle
grease every three months or 50 hours of tool use.
To install a replacement Chain: Turn the Chain Tension Adjusting Screw (39)
counterclockwise to release tension. Using the accessory Hex Wrench (83),
unscrew and remove the Nut (75) that secures the Chain Saw Cover (77) to the
unit. The Guard Bar (73) contains a Guard Bar stud slot that fits over the Guard
Bar stud. The Guard Bar also has two chain tensioning pin holes which fit over
the chain tensioning pins. Place the Guard Bar onto the bar stud so that the
chain tensioning pins fit into the chain tensioning pin holes. Fit the Chain over
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
the Drive Gear (44) and into the Guard Bar groove. The cutters on the top of
the Guard Bar should face toward the Guard Bar tip, in the direction of the
chain rotation. Replace the Chain Saw Cover and secure with the Nut. Tighten
the Nut finger tight only to allow for tension adjustment.
Then, follow directions on page 10 of this manual to properly adjust the Chain
tension. (See Figure B, and Figure C.)
8.
9.
When storing the Polesaw/Pruner: Before storing, make sure to install the
Guard Bar Cover (78) onto the Guard Bar (73). Drain all fuel out of the tool’s
Fuel Tank (78A). If this is not followed, old fuel in the Fuel Tank may clog the
Carburetor and prevent the tool from starting until cleaned out. Then store the
tool in a clean, dry, safe location out of reach of children and other unauthorized
people.
CAUTION! All maintenance, service, or repairs not mentioned in this
manual must only be performed by a qualified service technician.
SAW
CHAIN
(74)
CHAIN SAW
COVER
(77)
NUT
(75)
GUARD BAR
(73)
CHAIN SAW
COVER
(77)
CHAIN
TENSION ASSY.
(38)
NUT
(75)
1
2
DRIVE GEAR
(44)
CHAIN
(74)
CHAIN ROTATION
DRIVE
GEAR
(44)
GUARD BAR
STUD
SLOT
GUARD BAR
(73)
GUARD BAR
STUD
NUT
(75)
CHAIN TENSIONING
PIN HOLES
3
4
FIGURE C
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Guard Bar and Chain running hot and
smoking.
Possible Cause
1. Chain tension too tight.
Possible Solution
1. Re-adjust Chain Tension Adjusting Screw to
lesson tension on Chain.
2. Chain Oil Tank empty.
1. Chain tension too tight.
2. Refill Chain Oil Tank.
1. Re-adjust Chain Tension Adjusting Screw to
lesson tension on Chain.
Engine runs, but Chain is not rotating.
Chain rotates while Engine is at idle.
2. Damaged Guard Bar and/or 2. Have a qualified service technician repair or
Chain.
1. Engine idle speed set too
high.
replace Guard Bar and/or Chain.
1. Have a qualified service technician reset
Carburetor idle adjustment Screw to lower
idle (RPM) speed.
Power Switch does not turn off
Engine.
1. Defective Power Switch.
1. Immediately remove Spark Plug Cap from Spark
Plug to stop Engine. Discontinue using Polesaw/
Pruner until the tool is repaired by a qualified
service technician.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT HE
OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS, AND NOT BYTHE BUYER. THE BUYER
ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTSTHERETO.
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - POLESAW/PRUNER UNIT
Part #
1
2
3
4
5
6
7
8
Description
Engine Assembly
Pipe Support (Bottom)
Control Lever (Left)
Screw
Safety Lever Spring
1/3 Throttle Lever
Connector (B)
Throttle Lever
Safety Lever
Power Switch
Control Lever (Right)
Large Lever Spring
Hanger Assy.
Shoulder Harness
Screw
Part #
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
Description
Washer
Drive Gear
Screw
Spring Washer
Oil Pump
Oil Pipe
Bearing
Gear Box Grease Fitting
Washer
Washer
Bearing
Washer (#9)
Drive Gear
Washer
Spring Washer
Screw
Screw
Washer
Gear Box
Screw
Spring Washer
Washer
Sprocket
Washer
Chain Oil Tank Cap
Ventilator
Chain Oil Tank
Spring Washer
Washer
Screw
Guard Bar
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Nut
Transmission Cover
Bearing
Socket Head Bolt
Pipe Cover
Orientation Block
Connector
Spring
Washer
Spring Washer
Screw
Washer
Screw
Safety Guard
Special Washer
Wing Nut
Bearing
Pipe Support (Top)
Plastic Pipe
Long Axis Transmission
Screw
Gear Box Cover
Tension Assy.
Chain Tension Adjusting Screw 81
Screw
Saw Chain
Nut
Special Washer
Chain Saw Cover
Guard Bar Cover
Transmission Short Axis
Screwdriver
Spark Plug Wrench
Tool Pouch
Hex Wrench (Qty. 2)
82
83
Bearing
Drive Gear Axis
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 18
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM - POLESAW/PRUNER UNIT
83: Hex Wrenches not shown.
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - ENGINE
Part #
1A
2A
3A
4A
5A
6A
7A
8A
Description
Screw Set
Part #
45A
46A
47A
48A
49A
50A
51A
52A
53A
54A
55A
56A
57A
58A
59A
60A
61A
62A
63A
Description
Air Filter Support
Carburetor
Screw
Choke Lever
Screw Set
Insulator Gasket
Insulator Seat
Carburetor Gasket
Inner Hex Bolt
Spark Plug Cap
Spark Plug
Lead Rope Set
Starter Cover
Starter Handle
Starter Pulley
Starter Spring
Starter Rope
Screw
9A
Starter Spring
Back Stop
10A
11A
12A
13A
14A
15A
16A
17A
18A
19A
20A
21A
22A
23A
24A
25A
26A
27A
28A
29A
30A
31A
32A
33A
34A
35A
36A
37A
38A
39A
40A
41A
42A
43A
44A
Starter Bowl
Inner Hex Bolt
Rear Crankcase
Position Pin
Rear Oil Seal
Ball Bearing
Crankcase
Front Crankcase
Flywheel
Centrifugal Clutch 64A
Clutch Spring
Ripple Washer
Clutch Screw
Clutch Drum
Bearing
Cylinder
Cylinder Gasket
Piston Ring
Piston
Piston Pin Ring Snap
Crankshaft Assy.
Needle Bearing
Piston Pin
Piston Pin Ring Snap
Woodruff Key
Screw Set
Muffler Gasket
Baffle
Muffler
Inner Hex Bolt
Screw Set
Protection Cover
Engine Cover
Fuel Cap
Air Vent
Plate
Rubber Gasket
Fuel Tank
Retainer
Hose Grommet
Fuel Hose
Fuel Filter
65A
66A
67A
68A
69A
70A
71A
72A
73A
74A
75A
76A
77A
78A
79A
80A
81A
82A
83A
84A
85A
86A
86A
87A
Block
Switch Wires
Screw Set
Cable Retainer
Ignition Coil
Flywheel Cover
Screw Set
Screw Set
Card Spring
Clutch Cover
Screw Set
Screw Set
Nut
Pin
Screw Set
Knob Screw
Air Filter Cover
Air Filter
Screw Set
Choke Valve
Cable Retainer
Flat Washer
Protection Cover
Protection Cover
Primer
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 20
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM -ENGINE
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Emission Control System Warranty
United States Emission Control Defects Warranty Statement
®
The United States Environmental Protection Agency (herein EPA), and Harbor Freight Tools (herein HFT) are pleased to
explain the emission control system warranty on your 1995 and later Small Off-Road Engine (herein engine). Within the
United States, new off-road, spark-ignition engines certified for model year 1997 and later, must meet similar standards
set forth by the EPA. HFT must warrant the emission control system on your engine for the periods of time described
below, provided there has been no abuse, neglect or improper maintenance of your engine.
Your emission control system may include parts such as the carburetor or fuel-injection system, and the ignition system.
Also included may be hoses, belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, HFT will repair your engine at no cost to you including diagnosis, parts and labor.
Manufacturer’s Warranty Coverage
The 1995 and later engines are warranted for two (2) years. If any emission-related part on your engine is defective, the
part will be repaired or replaced by HFT.
Harbor Freight Tools Emission Control Defects Warranty Coverage
Engines are warranted for a period of two (2) years relative to emission control parts defects, subject to the provisions set
forth below. If any emission related part on your engine is defective, the part will be repaired or replaced by HFT.
Owner’s Warranty Responsibilities
-
As the engine owner, you are responsible for the performance of the required maintenance listed in your Owner’s
Manual. HFT recommends that you retain all receipts covering maintenance on your engine, but HFT cannot deny
warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
-
-
As the engine owner, you should, however, be aware that HFT may deny you warranty coverage if your engine or a part
has failed due to abuse, neglect, improper maintenance, or unapproved modifications.
You are responsible for shipping your engine to a HFT warranty station as soon as a problem exists. Contact the HFT
Customer Service department at the number below to make shipping arrangements. The warranty repairs should be
completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact the Harbor Freight Tools
Customer Service Department at 1-800-444-3353.
Harbor Freight Tools Emission Control Defects Warranty Provisions
1. Length of Coverage
HFT warrants to a first retail purchaser and each subsequent purchaser that the engine is free from defects in mate-
rials and workmanship that cause the failure of warranted parts for a period of two (2) years after the date of delivery
to the first retail purchaser.
2. No Charge Repair or Replacement
Repair or replacement of any warranted part will be performed at no charge to the owner if the work is performed
through a warranty station authorized by HFT. For emissions warranty service, contact the HFT Customer Service
Department at 1-800-444-3353.
3. Consequential Damages Coverage
Coverage under this warranty shall also extend to the failure of any engine components caused by the failure of any
warranted part while it is still covered under this warranty.
4. Coverage Exclusions
Warranty claims shall be filed in accordance with the provisions of the HFT warranty policy explained in the box at the
top of the previous page. HFT shall not be liable for any loss of use of the engine, for any alternative usage, for any
damage to goods, loss of time, or inconvenience. Warranty coverage shall also be excluded for any part which fails,
malfunctions, or is damaged due to failure to follow the maintenance
and operating instructions set forth in the Owner’s Manual including, but not limited to:
(a) use of parts which are not authorized by HFT
(b) improper installation, adjustment or repair of the engine or of any warranted part unless performed by an autho-
rized warranty center
(c) failure to follow recommendations on fuel use contained in the Owner’s Manual
(d) improper or inadequate maintenance of any warranted parts
(e) repairs performed outside of the authorized warranty service dealers
(f) alterations by changing, adding to or removing parts from the engine.
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Emission Control System Warranty - continued
Harbor Freight Tools Emission Control Defects Warranty Provisions
5. Service and Maintenance
Component parts which are not scheduled for replacement as required maintenance or are scheduled only for regular
inspection to the effect of “repair or replace as necessary” are warranted for the warranty period. Any warranted part
which is scheduled for replacement as required maintenance is warranted for the period of time up to the first sched-
uled replacement point for that part. Any replacement part, provided it is equivalent in durability and performance,
may be used in performance of maintenance or repairs. The owner is responsible for commissioning a qualified
technician/mechanic to perform all required maintenance, as outlined in the Inspection, Cleaning, and Mainte-
nance section on pages 15 and 16 of this manual.
6. Warranted Parts
1) Fuel Metering System
i)
Carburetor and its internal parts.
ii) Fuel pump (if so equipped).
iii) Cold start enrichment system.
2) Air Induction System
i)
Intake pipe/manifold.
ii) Air cleaner.
3) Ignition System
i)
Spark plug.
ii) Magneto ignition system.
4) Catalyst System (if so equipped)
i)
Exhaust pipe stud.
ii) Muffler.
iii) Catalytic converter (if so equipped).
5) Miscellaneous items Used in Above Systems
i)
Vacuum, temperature and time sensitive valves and switches.
ii) Hoses, belts, connectors, and assemblies.
WARRANTY
LIMITED
90 DAY/1YEAR
WARRANTY
Harbor FreightTools Co.makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser for a period of ninety days from date of purchase that the motor, the belts
(if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.Harbor Freight
Tools also warrants to the original purchaser, for a period of one year from date of purchase, that all other parts
and components of the product are free from defects in materials and workmanship.This warranty does not apply
to damage due directly or indirectly to misuse, abuse, negligence or accidents; repairs or alterations outside our
facilities; or to lack of maintenance.We shall in no event be liable for death, injuries to persons or property, or for
incidental, contingent, special or consequential damages arising from the use of our product. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.
Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection
verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of
our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 95283
For technical questions, please call 1-800-444-3353
PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
|