Cateye Bicycle MODEL EC 1600 User Manual

Cateye Ergociser

MODEL EC-1600

OPERATING INSTRUCTIONS

EC-1600

Download from Www.Somanuals.com. All Manuals Search And Download.

Name of parts

CONTROL

Printer Cover

UNIT

RESET

Reset Button

Thermal Paper

Paper Cutter

Paper Guide

Resets the program back to initial state.

Pitch Sound Button

Turns on or off the pitch sound. When the pitch

sound is on,

symbol appears on the LCD.

Printer Button

Turns on or off the printer function. When the

printer is on, symbol appears on the LCD.

Value Adjust Button

Before exercise

----increases or decreases the blinking

EC-1600

RESET

numerical value by 10. [For pedal torque

(kg·m), by 1.0]

HEART

RATE

CADENCE

----increases or decreases the blinking

numerical value by 1. [For pedal torque

(kg·m) by 0.1]

PROGRAM

NAME

TIME

PEDAL

WORK

RATE

* When selecting the gender, +

specifies

TORQUE

MALE, and -

During exercise

FEMALE)

----increases or decreases pedal torque by 1.0

kg·m.

TIME

----increases or decreases pedal torque by

0.1kg·m.

Interval Training Preference

TLD 1. 15 sec. work 45 sec. relief

Dash (Sprint Power) Training

TLD 2. 30 sec. work 60 sec. relief

Speed (Anaerobic Power) Training

TLD 3. 60 sec. work 30 sec. relief

Stamina (Aerobic Power) Training

TLD.4. Make a training pattern as desired.

INSTRUCTIONS

MODE

ADV

1. Attach the pulse sensor.

MODE

2. Press

until desired program

name flashes.

Mode Button

MODE

ADV

3. Press

4. Press

digits.

to enter the program.

to adjust blinking

Before exercise

Used to select the program and to change the

item of data to input.

MODE

5. Press

to let other digits blink.

Hill Profile Preference

Repeat 4 & 5.

Intensity of program is adjusted

according to PRF Number.

PRF 1 is least intense.

PRF 8 is most intense.

PRF 9. Design a profile as desired.

ADV

6. Press

to start the program.

During exercise

D isplays the elapsed time or the calorie

consumption alternatively.

ADV

ADV Button

Makes the program proceed to the subsequent

stage.

LCD Panel

Card Inlet

LCD PANEL

Cadence Unit

Physical Fitness Level

Age

Error Symbol

ml/kg·min

Maximum Oxygen Uptake

Upper Pulse Limit

Pulse Symbol

rpm

PFL

AGE

MOU

PLL

Program Symbol

TEST ------- Aerobic power measurement

AUTO ------ Automatic training

CONST ----- Isopower training

INTVL ----- Interval training

HILL -------- Hill profile training

MANUAL - Manual training

Target Torque

Elapsed Time

TEST

AUTO

CONST

min:sec

kglb

kcal

Weight

INTVL

HILL

Calorie Consumption

MANUAL

Target Pulse

TPL

TLD

PWC

watt

bpm

TTQ

PRF

Target Load

Exercise Preference

Sex Distinction Symbol

Physical Work Capacity

kg·m

(Male)

(Female)

Load Scale Value

Warm Up Symbol

Cool Down Symbol

WARM

COOL

Load Scale

(Pedal Resistance)

Pitch Sound Symbol

Card Symbol

Printer Symbol

Battery Symbol

Time Scale

TIME

Download from Www.Somanuals.com. All Manuals Search And Download.

Paper Case

Select Switch

Paper Case Guide

Reading Stand (OPTION)

Fixing Screw Holes

Mounting screw holes

Cable Inlet

Battery Case

Pulse Sensor Jack

MAIN UNIT

Control Unit

Handlebar

Paper Case

Handlebar Lever

Saddle

Handlebar post

Outer Cover

Handlebar post

Inner Cover

Seat Post

Spring Lock Pin

Adjusting Knob

Power Switch

Crank

Pedal

AC Adapter Inlet

EC-1600

Front Leg/Leg

pipe covers

Rear Leg/

Leg pipe covers

Caster

Levelling Knob

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Thank you very much for your purchase of the Model EC-1600 Cateye Ergociser™. The

model EC-1600 is a new high-tech exerciser with a built-in computerized training system

designed specifically to promote cardiovascular fitness and overall endurance, the keystone

of good health. With its endurance test program and four training programs, the EC-1600

will help you to maintain or improve your physical strength in a fun and pleasant way. We

hope you will make good use of your Cateye Ergociser™ for years to come.

Before using your new exerciser, please read this manual carefully. Then store it in a safe

place along with the warranty card.

FOR SAFE OPERATION

For safe use, always observe the following rules.

1. Before using the EC-1600, it is important to consult a medical specialist if you are suffer-

ing from any of the following : heart disease (angina pectoris, myocardial infarction),

hypertension, diabetes, respiratory disease (asthma, chronic bronchitis, pulmonary em-

physema, etc.), articular metamorphosis, rheumatism, gout, or other diseases and physi-

cal complaints. Pregnant women should also consult their doctor before commencing a

training program.

2. If you are not used to regular physical activity, it may be dangerous to suddenly engage in

strenuous activity. Increase your exercise level gradually.

3. If you feel sick or sense that something is wrong with your body during exercise, stop

immediately.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this exerciser.

DANGER

To reduce the risk of electric shock:

1. Always unplug this AC adapter from the electrical outlet immediately after using and before cleaning.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

1. An AC adapter appliance should never be left unattended when plugged in. Unplug from outlet when not in use,

and before putting on or taking of parts.

2. Close supervision is necessary when this exerciser is used by, on, or near children, invalids, or disabled persons.

3. Use this exerciser only for its intended use as described in this manual. Do not use attachments not recommended

by the manufacturer.

4. Never operate this exerciser if it has a damaged cord or plug, if it is not working properly, if it has been dropped

or damaged, or dropped into water. Return the exerciser to a service center for examination and repair.

5. Do not carry this exerciser by supply cord or use cord as a handle.

6. Keep the cord away from heated surface.

7. Never operate the exerciser with the air openings blocked. Keep the air openings free of lint, hair, and the like.

8. Never drop or insert any object into an opening.

9. Do not use outdoors.

10. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

11. To disconnect, turn all controls to the off position, then remove plug from outlet

This exerciser is intended for both household and commercial use.

This equipment has been certified to comply with the limits for a Class B computing device, pursuant to Subpart J of

Part 15 of FCC Rules. Only peripherals (computer input/output devices, terminals, printers, etc.) certified to comply

with the Class B limits may be attached to this computer. Operation with non-certified peripherals is likely to result

in interference to radio and TV reception.

SAVE THESE INSTRUCTIONS.

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Assembling

2 Installing the control unit

3 Adapting the pulse sensor

4 How to adjust each part

5 Your first ride

6 The six programs of operation

7 Using your Ergociser without a data card

Make sure all components are included in a package.

Control Unit

Saddle

EC-1600

Main Body

Handlebar post Assembly

Legs (2 pcs.)

Leg Covers (4 pcs.)

Pedals (L,R)

AC Adapter

atey

e E

cise

EC-16OO

Data Card (10)

Start Card (1)

Batteries

(AAA x 2)

Operating Instructions

Warranty Card

Pulse Sensor

Sensor Clip

Tools

Download from Www.Somanuals.com. All Manuals Search And Download.

Assembly

1.Attaching the legs

2. Mounting the handlebar

post

3. Connecting the control

cable

4.Mounting the saddle

5.Attaching the pedals

• Remove the two screws from the

respective leg pipes. The one with

casters should be used as front leg.

• Pull the spring lock pin and lift up • Use the No.15 end of the spanner

• Remove the handlebar post knob. • Connect the connector from the

the seat post to a proper height for

saddle mounting.

to attach the pedals firmly to the

cranks.

handlebar post cover with that

• Insert the handlebar post into the

from the body in correct direction,

main body, with the post holes fac-

keeping the lower connector cable

ing forward.

• Place the front leg under the front

end of the main body with casters

facing forward, and adjust the po-

sition so that the screw holes meet

the fastening points.

• Mount the saddle onto the top of • The right and left pedals are dif-

at the center of the post front.

seat post in position and tighten

the nuts with wrench No.15.

ferent, so be sure to check for R

and L marks.

• Adjust the post position so that

• Slide down the inner post cover

the lowest post hole of the three

and squeeze it into the body until

meets the post knob screw hole,

it clicks in position.

• Tighten the right pedal by turning

clockwise, and the left pedal by

turning counterclockwise.

and fasten the post knob securely.

• Fasten the leg with the two screws

securely.

It will be easier to screw in if you

slightly lift the handlebar post.

wrench No.15

Saddle

handlebar post

screw

seat post

connectors

wrench No.15

crank

tighten

leg pipe

Front

left (L)

Front

right (R)

outer post cover

caster

loosen

inner post cover

handlebar post knob

screw

crank

squeeze in

Caution: If the pedals are not at-

tached firmly enough to the

crank, they can cause an irri-

tating noise. Be sure to attach

them firmly.

Note: Watch the cable connec-

tors when sliding down the in-

ner post cover.

Rear

leg pipe

F-R

F-L

EC-1600

• Hook the leg cover at the end of

each leg and fix it in position with

adhesive tape as illustrated.

leg cover

R-R

Note: When placing leg covers,

follow the location markings

on the back thereof.

hook

Adhesive tape

R-L

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the control unit

1.Loading backup batteries

2. Printer use

3. Units for body weight

4. Strength evaluation table

5. Installing the control unit

• The battery case cover is on the • U se select switch No.4 on the

• Use select switch No.3 on the back

of the control unit to choose kilo-

grams or pounds as your unit of

body weight.

• By using select switches No.1 and • Insert the cable connector from

• Using the four screws provided,

mount the control unit on the

handlebar post.

back of the control unit. You can

open the cover by sliding off.

back of the control unit to activate

or deactivate the printer.

2 in the aerobic power measure-

ment (physical fitness test) pro-

gram, you can change the internal

tables by which your strength is

judged.

the handlebar post into the cable

inlet on the back of the control

unit.

• Load batteries (size AAA x 2) in

the battery case as shown in the

diagram. Make sure the polarity is

right, and close the case.

NO.4-OFF --printer activated

NO.4-ON ---printer deactivated

NO.3-OFF ---------- kg

NO.3-ON ----------- lb

• This switch is initially set at

"OFF" at our Factory, to activate

the printer. In order that you will

get familiar with the printer func-

tion, please leave this switch as it

is at this stage.

• When the Model EC-1600 Cateye

Ergociser™ leaves the factory, it is

set for American use.

Caution: When oxygen uptake

(VO₂max) is estimated in the

aerobic power measurement

(physical fitness test) pro-

gram, body weight in kg is

used. If you mistakenly as-

sume the unit for body, the fig-

ure given for oxygen uptake

will be wrong by a wide mar-

gin.

batteries (size AAA)

1-ON 2-OFF

American use

Evaluation table by AHA Com-

mittee: " E xercise testing and

training of apparently healthy in-

dividuals, A handbook for physi-

cians (1972)"

screw

Note: Though you set NO.4 at

"OFF", you can temporarily

deactivate the printer by de-

pressing printer button on the

control panel. (Printing mark

on LCD panel will disap-

pear.)

cable inlet

cable connector

battery case cover

1-OFF 2-ON

European use

Evaluation table by Dr. Åstrand:

"The values from P. -O. Åstrand,

Work tests with the bicycle er-

gometer"

Caution: Insert the cable con-

nector until it is firmly locked.

The control unit will not func-

tion properly with a partial or

faulty connection.

handlebar post

Note: The Model E C-1600

Cateye Ergociser™ uses bat-

teries for memory mainte-

nance so that the date in the

machine's memory is always

correct even when the main

power supply is turned off.

These batteries will last two

years under conditions of nor-

mal use. When the battery

When NO .4- is set at O N,

printer button

on the main

control panel does not func-

tion.

1-OFF 2-OFF

Japanese use

Evaluation table by Dr. Ikegami:

"Exercise prescriptions in theory

and practice"

select switch

symbol

lights up on the

liquid crystal screen, replace

batteries as soon as possible. If

you keep the main power sup-

ply of the exerciser turned on

when you replace batteries,

there will be no interruption

in the machine's memory.

select switch

cable inlet

1 2 3 4

OFF

battery case cover

pulse sensor jack

Download from Www.Somanuals.com. All Manuals Search And Download.

Adapting the pulse sensor

1. Connecting the pulse 2. Handling of sensor cable

sensor

3. Using pulse sensor

during exercise

4.Checking the Pulse

Sensor

This model detects and

displays your pulse rate

during exercise by the

pulse sensor from your

earlobe. Being a sensitive

electronic part, the pulse

sensor must be handled

with sufficient care.

• A ttach the sensor clip on the

• Clip the pulse sensor at the center

of your right or left ear lobe.

handlebar with the sensor cable in

• Insert the pulse sensor plug into

• You can check the function of the

pulse sensor on the LCD screen

during the exercise.

between, and adjust the length of

the sensor jack on the back of con-

• Ear rings or other ornaments must

be removed before attaching the

sensor and during exercise.

the sensor cable.

trol unit.

• When not in use, keep the earlobe

sensor attached on the clip.

• R emove the pulse sensor from

your earlobe during exercise, then

close it.

• When it is cold, massage your ear-

lobe before use to improve blood

circulation.

sensor clip

• The pulse sensor is normal if the

pulse rate drops to zero and the

symbol goes out.

pulse (earlobe) sensor

• Try not to change the position of

the pulse sensor during the exer-

cise.

• If the pulse rate does not drop to

pulse sensor jack

zero or if the

symbol remains

• If the

symbol frequently lights

O N, the cable may be discon-

nected. If the cable proves to be

disconnected, replace the pulse

sensor with a new one (sold sepa-

rately).

up during use, remove once and

re-attach the pulse sensor.

• A ttach the cable clip to your

clothes to prevent excessive

swinging of the sensor cable.

pulse sensor plug

• Always clip the pulse sensor to the

sensor clip when it is not being

used. This sensor clip can also be

used to adjust the slack of the

cable.

cable clip

• When removing the pulse sensor

after exercise, be sure to remove

also the cable holder.

• The pitch sound is cancelled if the

sensor plug gets out of the jack of

control panel. Pay attention to the

complete connection of the plug.

pulse (earlobe)

sensor

pulse (earlobe) sensor

cable clip

Download from Www.Somanuals.com. All Manuals Search And Download.

How to adjust each part

1.Adjusting the saddle

height

2. Adjusting the handlebar

height

3. Adjusting the handlebar

angle

4. Adjusting the pedal belt

5. The levelling knobs

6.Adjusting all parts to fit

• The pedal belt length of the EC- • Ideally, you should only use your • Make various height and angle ad-

Handlebar height can be roughly se- • When you turn the handlebar le-

1600 can be adjusted according to

your shoes size.

exerciser on a hard, level floor.

justments so that your posture

when seated on the exerciser is

like that shown in the diagram be-

low.

lected in 3 steps, and further adjust-

ment can be done by rotating the

handlebar. The handlebar is at the

highest position, i.e. at the MAX.

guide line right now. If you want to

change the handlebar height, follow

the procedure hereunder.

ver clockwise (when mounted),

the handlebar is loosened. The le-

ver turns idle when pulled down-

ward.

• Pulling on the spring lock pin will en-

able you to move the seat post up or

down. When the saddle is at the cor-

rect level for you, release the knob

and move the seat post slightly.

• If the exerciser tilts or wobbles

during use, turn one or more level-

ling knobs until a stable position is

maintained.

• For proper saddle height, your

knees should be slightly bent

when the pedal is at its lowermost

position.

• Rotate the handlebar and hold it

at the desired angle.

• A spring inside the spring lock pin

will drive a pin into the nearest

hole in the seat post, locking it in

that position.

• Turn the handlebar lever counter-

clockwise to fix the handlebar

angle.

outer post cover

• For proper handlebar height and

angle, you should be leaning

slightly forward when holding the

handlebar.

• The pitch of the seat post holes is

1" (approx. 25mm).

highest

levelling knob

MAX. line

seat post

higher

lower

• When you move the exerciser, lift

the saddle and roll the exerciser

on its casters.

handlebar lever

pitch 1"

(approx. 25mm)

handlebar

medium

3 steps

lowest

loosen

tighten

Pull

idle

• Holding the outer post cover, re-

move handlebar post knob. (See

Note 1 below)

spring lock pin

• Place lower edge of outer post

cover either at the lower guide

line marked on the inner cover, or

at the bottom of the inner cover.

Caution: Do not attempt to ad-

just the saddle height while

you are mounted.

Slide

• Supporting the outer post cover in

position, insert post knob and

tighten it securely.

guide line

• Pitch of the guide lines is 3 inches

(approx. 76mm).

EC-1600

Note 1: Be sure to grasp the

outer post cover and keep it in

position when removing the

post knob, in order to avoid

sudden drop that may cause

damages to the unit.

Standard exercise posture

Note 2: Do not lift outer post

cover above the MAX. guide

line, otherwise the cable can

break.

handlebar post knob

Download from Www.Somanuals.com. All Manuals Search And Download.

Your first ride

ADV

1.Turn on power and attach 2. Insert the start card (red

3. Checking the screen

display

4. Press the

to start

button

5.Calorie display

6. When you finish

pulse sensor

card provided)

• Pushing the MODE button gives • When 16 minutes have elapsed, a

• Insert the DC connector of the • Find the red card (start card) in • The display that appears on the

• Depress ADV

button. This will

you the option of viewing a calorie

consumption display (calorie con-

sumed from the beginning of the

present training session until now)

instead of elapsed time.

buzzer will sound and the training

session will automatically stop.

AC adaptor into the AC adapter

inlet at the rear of the exerciser.

the packaging of the exerciser. In-

sert this card into the appropriate

slot (card inlet) as shown in the

diagram below.

screen should be as described be-

low. If this display does not ap-

pear, pull the card out and slowly

insert it again. The numbers in the

display represent training condi-

tions.

activate the printer.

• Start pedaling at a low speed.

• The printer prints out the E.C.

(Energy Consumption) and then

stops.

• Insert the A C plug of the A C

adaptor into any household AC

outlet (120V).

AC adapter inlet

• When the printer stops, a display

like that in the diagram below will

appear on the screen. The num-

bers on this screen represent your

own present condition, and they

will change frequently.

card inlet

start card

• Now you are on the exerciser for

your first ride. As you train, pedal

resistance will change, energy ex-

penditure will change, and your

pulse rate will also change. The

Model E C-1600 lets you keep

track of all this information while

you train.

• You may stop exercise program at

any time during workout by press-

ADV

connector

PLL

ing

button twice.

AGE

min:sec

• The liquid crystal display on the

screen will return to initial display,

"AUTO" alone flashing.

HILL

rpm

PRF

min:sec

• The Model EC-1600 Cateye Ergo-

ciser™ function that we have ex-

plained up to this point is only the

beginning. Let us move on to an

explanation of other functions.

HILL

kg•m

rpm

watt

Caution: Use only the red card

at this stage. It is a sample card

with the exercise data already

registered in it. The unit will

not work with the black cards

since they do not contain any

data yet.

kg•m

TIME

kg•m

HILL

kcal

watt

1 Age is shown by the figure "50"

power switch

kg•m

TIME

2 "150" is the upper-limit pulse

rate set by the machine (200 -

age). If this pulse rate is ex-

ceeded during training, an alarm

will sound and the pedal resis-

tance will become to minimum

(0.5kg·m).

kg•m

• Turn on power switch. The control

unit should make a beep sound

and "AUTO" should appear on

the screen.

1 Heartbeats per minute.

2 Pedal revolutions per minute.

TIME

3 Elapsed time since start of train-

ing session.

3 E xe r cise time is sh o wn b y

"16:00", which means 16 min-

utes.

4 Energy expenditure, expressed

in watts. The higher the number,

the more energy you are expend-

ing.

AUTO

Insert this

direction

4 "HILL" which is short for "hill

profile training" shows the type

of training to be engaged in.

5 Pedal resistance. The higher the

number, the harder it is to pedal.

5 "1" indicates the shape of the hill

to be climbed. "1" is the gentlest

slope.

6 A s time goes on, the blinking

row in the graphic part will shift

one by one toward the right

hand. According to the position

of the blinking row you can find

how far you have progressed in

the current session.

TIME

start card

• Attach the pulse sensor to your

earlobe. When it is cold, rub your

earlobe to facilitate blood circula-

tion before attaching the pulse

sensor.

6 Changes of pedal resistance are

shown on the graph.

Remark : You may change data at any time. The

and

buttons will raise or lower any of the num-

Caution: D o not use any A C

adaptor other than the one

supplied with the Model EC-

1600.

bers discussed above. Press the MODE button to

move to the next number, which will flash on and off

when it is eligible for changing. Now, however, the

goal is to get you acquainted with Model EC-1600, so

if you change any of the numeral values, please return

them to their original setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

The six programs of operation

1.Aerobic power

measurement

2. Automatic training

3. Isopower training

(training at a constant

energy expenditure)

4. Interval training

5.Hill profile training

( training by cycling up

mountains )

6.Manual training

(training at any desired

pedal resistance)

(training at a constant pulse rate)

(exercise + relief periods)

(physical fitness test)

• You set the pulse rate at which

you want to exercise and the

Model EC-1600 automatically ad-

justs pedal resistance to maintain

that pulse rate. This is an ideal ba-

sic form of aerobic training.

• Over a period of 10 minutes, you

will encounter three different lev-

els of pedal resistance. Your pulse

will change in response to the dif-

ferent levels of resistance, and this

change in pulse will be used to cal-

culate your overall fitness level,

also expressed is MO U (VO ₂

max). MOU stands for maximum

oxygen uptake. The higher your

overall fitness level, the greater

your endurance.

• The work rate or the figure for en-

ergy expenditure (watts) shown

on the screen of the Model EC-

1600 is calculated from pedal re-

sistance (kg·m) and cadence

(rpm).

• By switching back and forth be- • Pedal resistance changes over • You choose the pedal resistance

tween exercise and relief periods

of varying length, interval training

gives you the kind of program that

professionals use to build their

stamina and energy.

time to simulate the effect of cy-

clin g in t h e m o u n t a in s. A ll

changes in pedal resistance are

shown on the screen.

(torque: kg·m), and it stays con-

stant regardless of your pulse rate

or pedal cadence. This is the most

traditional way in which station-

ary bicycles have been used.

• The following eight types of

mountain profiles plus one cus-

tomized pattern are programmed.

• On the model EC-1600, 3 patterns of

interval training programs are preset

for developing dashing power, speed,

or your stamina respectively, PLUS

one customized pattern for you to in-

put your personal program.

• As you repeat the exercise at a

certain pulse rate and make

progress in your fitness level, you

will be able to create a greater

work intensity under the same

pulse rate. Further, you will be

able to try exercising at a higher

target pulse rate.

• In isopower training, you set the

desired work intensity in watts.

The Model E C-1600 automati-

cally adjusts the pedal resistance

(kg·m) depending on your pedal

cadence (rpm), so as to keep a

constant work rate in watts.

Torque setting range:

0.5~4.0 kg·m

Minimum graduation:

0.1 kg·m

PRF-1: the Apennines (Italy)

PRF-2: the Apparachian

(U.S.A.)

PRF-3: the Cascades (U.S.A.)

PRF-4: the Pyrenees

TLD-1: dash strength training

(sprint power)

15 seconds exercise fol-

lowed by a 45 second relief.

TLD-2: speed training

(anaerobic power)

• Your MO U value is compared

with the MO U values of other

people who are the same age and

sex as you. You are given a physi-

cal strength number from 1 to 5

depending on how you rank.

(France, Spain)

TORQUE

• This type of training is also called

constant load, and is often used in

cardio-vascular rehabilitation.

PRF-5: Mount Fuji (Japan)

PRF-6: the Rockies (U.S.A.)

PRF-7: the Alps (Switzerland)

PRF-8: the Himalayas (Nepal)

PRF-9: customized pattern

Control range:

30 seconds of exercise fol-

lowed by a 60 second relief.

PULSE RATE

cadence: ----- 40~100 rpm

wattage: ------ 25~200 watts

• These results should give you a

good idea of your own fitness level

and help you to determine what

sort of training program will be

the most effective for you. For in-

formation on how to choose a

training program, refer to "Your

strength level and training index"

on page 22~25 in the Operation

section on this booklet.

TLD-3: stamina training

(aerobic power)

60 seconds of exercise fol-

lowed by a 30 second relief.

TLD-4: customized pattern

• The mountain profiles from 1 to 8

are arranged in order of ascending

difficulty. Do not strain yourself,

but rather enjoy the form of each

mountain.

Note: If you set your target watt-

age as under 50 watts, control

limit of cadence (rpm) be-

comes under 100 rpm.

• Choose one of the above patterns, and

adjust the level of intensity by specify-

ing pedal resistance (torque: kg·m).

• Selecting PRF-9 customized pat-

tern, you can create and input

your original hill profile. (Also re-

fer to pages 40 and 41.)

• During the exercise period (increased

load portion of interval), you should

pedal with your greatest effort, then

you should pedal slower and lighter

during relief period (lower load por-

tion of interval).

• Minimum training time is 16 min-

utes. If you set a longer training

time, the mountain profiles will be

stretched out horizontally.

WORK RATE

TORQUE

• In the TLD-3 stamina training pro-

gram, it is advisable to pedal fast

enough in the exercise period to

keep your pulse rate at 60~80% of

the maximum pulse rate for your

age. (Refer to page 22~23)

PRF-5:

Mount Fuji

PRF-1:

the Apennines

Upper Pulse Limit Alarm

• By choosing TLD-4 customized pat-

tern, you can write in your original pat-

tern as desired. (See pages 40 and 41.)

PRF-6:

the Rockies

PRF-2:

the Apparachian

• For your safety, the upper pulse limit alarm is provided in all the pro-

grams of the EC-1600. If your pulse rate exceeds this limit, the buzzer

beeps and the pedal resistance automatically drops to the minimum of

0.5 kg·m.

TLD-1:

dash strength training

PRF-7:

the Alps

PRF-3:

the Cascades

• If this alarm is activated, the program is suspended at that point and en-

ters the cool down phase, except in "Manual training" program in which

TLD-2:

speed training

you can continue the exercise using

torque again.

button to set the desired

PRF-8:

the Himalayas

PRF-4:

the Pyrenees

TLD-3:

stamina training

Download from Www.Somanuals.com. All Manuals Search And Download.

Using your Cateye Ergociser™ without a data card

The red card you used on your first ride contains the data

to select the type and condition of training. Without using

this card, it is also possible to run through the same

operations using the buttons on the control unit.

1.Switch on power supply

2. Select a training program

3. Input training conditions

4.Start training

5.At the end of training

• Plug in the AC adaptor and turn • With each press of the MODE

• The screen display will change to

the one shown in the diagram

here, with the number "40" flash-

ing.

• When you have set all the training • A buzzer will sound when the

R emark: Conditions vary ac-

cording to the training pro-

gram.

Upper limit pulse rate is auto-

matically determined from

your age, so there is no need

to revise this number yourself,

unless you have a particular

purpose.

conditions, press the

ADV

but-

training time you have set is fin-

ished. If you wish, you can con-

tinue training even after this

buzzer sounds.

on the switch at the rear of the

main body.

button, the flashing indicator

moves from one mode to another

in the following order.

ton. The printer will give a print-

out of training conditions. When

this printout is complete, the

screen display will change to the

one similar to what is shown be-

low. Then you can start pedaling.

• In the screen "AUTO" appears

blinking.

AUTO

:Automatic training

• Whenever you want to stop train-

ing, before or after the buzzer

sounds, push the ^ADVbutton

once.

PLL

AGE

min:sec

CONST :Isopower training

AUTO

rpm

TPL

PLL

bpm

INTVL

HILL

:Interval training

• The ^COOLsymbol appears on

the screen and the pedal resis-

tance drops to the minimum of 0.5

kg·m. This is the cooling down

function, which lasts for a maxi-

mum of 5 minutes.

• Let's try changing the displayed

target pulse rate from 120 to 115.

min:sec

AUTO

:Hill profile training

• Press the ^MODEbutton until

"120" is flashing. You want to re-

duce the number by five, so press

the – ¹button five times. Has

the number changed to "115"?

watt

TIME

kg·m

MANUAL :Manual training

TIME

kg·m

WARM

• You can raise or lower the flashing

number by pressing either the

rpm

:Aerobic power

measurement

TEST

TIME

button. The

min:sec

PLL

AUTO

and

buttons change the tens

AGE

• On your first ride, you tried the

hill profile training. This time

choose "AUTO" as example.

• The automatic training, isopower

training, interval training and

manual training programs all have

a warm-up function. Pedal resis-

tance increases slowly until you

reach your target pulse rate (Au-

tomatic training) or for the first

three minutes (all others). While

the warm-up function is operating,

^WARMsymbol will remain on the

screen.

column and the ones column of

each number separately. For ex-

ample, suppose you want to

change the displayed age number

from 40 to 52. Press + ¹⁰once

and + ¹two times. Has the num-

ber changed to "52"?

min:sec

watt

AUTO

kg·m

TPL

kg·m

bpm

• Press the ^MODEbutton until

"AUTO" flashes again, then press

COOL

ADV

to lock in your choice.

TIME

• At this stage review your workout

data such as time and calorie con-

sumption.

• With each press of the ^MODEbut-

ton, the flashing indicator moves

from one item to another in the

following order.

TIME

• The card is a tool for program

choice and setting training condi-

tions. It saves you the trouble of

setting the same training condi-

tions each time you use the exer-

ciser. For instructions on how to

make a card, please refer to page

42, "How to make a data card" in

the Operation section.

• Press the ADV button once

more and the printer will give a

printout of calories expended,

then the display turns to the initial

state. (If you stay in the cool down

phase for a full five minutes, you

do not have to push the ^ADV

button.)

• By pressing the ^MODEbutton

during the exercise, you can

switch the display from elapsed

time (TM min:sec) to calorie con-

sumption (EC Kcal), and vice-

versa.

AGE

PLL (upper limit pulse rate )

TM (training time)

TPL (target pulse rate)

• You should now understand how

to use the Model EC-1600 Cateye

Ergociser™. Once you get used to

the exerciser, you will probably

want to refer to the Operation sec-

tion for more detailed information

on functions, etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Your strength level and training index

2 Aerobic power measurement (Physical fitness

test)

3 Auto training

4 Isopower (constant load) training

5 Interval training

6 Hill profile training

7 Manual training

8 Setting your own training pattern

9 How to make a data card

Download from Www.Somanuals.com. All Manuals Search And Download.

Your strength level and training index (1)

Purpose of Exercise

Glossary ofTerms

• Have you ever been out of breath after climbing a flight of stairs or

after a brisk walk? When we are walking, running and even sleeping,

our body is taking in oxygen and generating energy. Oxygen taken in

by the lungs is sent to the entire body via the circulatory system. If the

function of the circulatory system , i.e. aerobic power, is insufficient,

we may experience being "out of breath" or experience yet other

physical problems.

• Maximum Heart Rate

The heart rate increases according to the intensity of exercise, there is

however a limit. The maximum heart rate that a person can sustain is

called the "maximum heart rate". Generally the heart rate declines as we

get older, this differs however between individuals, and is largely due to

how much one exercises.

• Difference Between the Heart Rate and Pulse Rate

The heart rate is the rate of the heart beat per minute measured by an

electrocardiograph. On the other hand, the pulse rate is measured as fol-

lows.

• We therefore perform "sports for the heart" (aerobic exercise), which

causes the heart to work a little more a few times a week, thus increas-

ing the oxygen supply to the body via the circulatory system. The pur-

pose of exercise with the Ergociser is to improve both your physical

strength and the functioning of the circulatory system: to improve our

aerobic power.

1)By palpating an artery near the skin surface, such as the carotid artery,

measure the pulse count of a blood vessel.

2)Transmit a sensor light to an earlobe or finger tip, and measure the

pulse count via the subtle changes of the sensor light transmission

caused by the heart beat.

Exercise Plan

• To effectively perform "sports for the heart" and to improve your

aerobic power, it is necessary to exercise according to your age and

physical fitness. If exercise exceeds your physical fitness level you only

injure your body. On the other hand, if the exercise is insufficient, a

positive effect cannot be expected.

Although the measurement principle and method are different, both the

heart and pulse rates have the same value per minute, and are therefore

regarded as synonymous.

• The Ergociser EC-1600 has 6 types of computer-controlled programs.

One program is the "Aerobic Power Measurement Program". This test

program evaluates your physical fitness level, while the other 5 pro-

grams are for actual exercise.

Since earlobes move very little during exercise and are not influenced

very much by physical movement, it is appropriate to use an earlobe to

measure the pulse rate during exercise. The Ergociser EC-1600 therefore

measures the pulse rate by detecting changes in the circulation of the ear-

lobe.

• The "Aerobic Power Measurement Program" evaluates your physical

fitness level so that you can determine the training index and begin

exercise based on the measured result. After exercising for a while

(about 3 months), you become aware of the effect on your body. Test

your physical fitness level again and gradually set a higher training in-

dex, thus maintaining and improving your physical fitness level. A spe-

cial feature of the Ergociser™ EC-1600 is that it combines testing with

exercise.

• Pulse Limit

As a standard maximum heart rate, "220–Age", "204–0.69 x Age", etc.

are used. With the Ergociser EC-1600, a somewhat lower value is used:

"200–Age". This pulse limit allows a person to safely exercise.

• Target Pulse Rate

The pulse rate to maintain during exercise as a target is called the "target

pulse rate". In the "Auto training" program, this pulse rate is automati-

cally maintained. However, even with other programs, always be con-

scious of your target pulse rate during exercise. Refer to the illustration

on the left.

Aerobic Power Measurement

Exercise Planning

Exercise

• Exercise Level Based on the Pulse Rate

The pulse rate increases according to the intensity of the exercise. In

other words, the pulse rate during exercise is a barometer for the exercise

level. The exercise level can be determined in percentages by the follow-

ing formula.

Note : You could also make up your

target pulse rate more simply by

deducting your age from a certain

figure. For a beginner, for in-

stance, it is recommendable to

start with [160–age (approx.

30~50% depending on your age)],

and gradually proceed to higher

level such as [180–age (approx.

50~70% )]. It would be ideal to

aim at [190–age] eventually.

Exercise Frequency andTime

• At least 15 minutes are required for one exercise period, however if

possible a 20 ~ 30 minute period is even better.

Pulse rate during exercise – Pulse rate at rest

Exercise Level (% ) =

x 100

Maximum heart rate – Pulse rate at rest

Therefore, if you want to discern the target of the exercise level from the

pulse rate (target pulse rate), you can calculate as follows.

• To maintain your present condition, exercise at lease twice a week, 3

times a week would improve your condition even more. The ideal how-

ever is to exercise every day or 5 ~ 6 times a week.

Target pulse rate = (maximum heart rate – pulse rate at rest)

Exercise Level (% )

+ pulse rate at rest

100

Download from Www.Somanuals.com. All Manuals Search And Download.

Your strength level and training index (2)

The "Aerobic power measurement" program evaluates your physical fitness

• Exercise for at least a 15 minute period. If possible a 20 ~ 30 minute period

is even better. Since warm up takes 3 minutes, set your exercise time to

"actual exercise time + 3 minutes".

Physical Fitness Level

andTraining Index

level according to 5 levels, it also evaluates your maximum oxygen uptake

with an estimated value. Based on the result, you can choose your own train-

ing index (program type and exercise intensity) from the following.

• Depending on the physical fitness level and purpose, some people may

exercise at a higher pulse limit than the value calculated by age. In such

instances, set the pulse limit slightly higher, being conscious of your own

physical condition.

1Automatic Training

• In this program, the exercise intensity is set by the target pulse rate (beats

per minute: bpm). Select your target pulse rate from the following table,

based on your age and physical fitness level (PFL) from 1 to 5.

• If you select the stamina aerobic power development pattern (TLD 3),

maintain your pulse rate in the 60 ~ 80% range of the illustration on page 22.

• If the target you select is difficult, reduce the target pulse rate by 10 bpm.

You need not work hard from the beginning, continuing is most important.

TLD 1

TLD 2

TLD 3

Pedal

Torque

Pedal

Torque

Pedal

Torque

PWC max

• This table is arranged so that even people who have not exercised so much

can benefit. The targets in this table may be too easy for people who exer-

cise often. If you have confidence, increase your target in 10 bpm units,

referring to the target zone in the illustration on page 22.

150 watt

200 watt

250 watt

300 watt

350 watt

400 watt

1.5 kg·m

2.0 kg·m

2.5 kg·m

3.0 kg·m

3.5 kg·m

4.0 kg·m

150 watt

200 watt

250 watt

300 watt

350 watt

400 watt

1.4 kg·m

1.8 kg·m

2.3 kg·m

2.8 kg·m

3.2 kg·m

3.7 kg·m

150 watt

200 watt

250 watt

300 watt

350 watt

400 watt

1.3 kg·m

1.7 kg·m

2.1 kg·m

2.6 kg·m

3.0 kg·m

3.5 kg·m

• Exercise for at least a 15 minute period. If possible a 20 ~ 30 minute period

is even better.

• If overweight control (calorie combustion) is the purpose of the exercise,

set the target pulse rate lower so that you can easily exercise even while

watching TV, but extend your exercise time longer, exceeding 30 minutes.

4Hill Profile Training

• Merely select one of the 9 patterns of this program. Try different hill pro-

files (shape of the mountain) in a range where you don't feel too much

difficulty. The exercise intensity can also be adjusted by pedaling slower

or faster depending on the changes of pedal resistance.

PFL

20~30s

110 bpm

120 bpm

130 bpm

40~50s

100 bpm

110 bpm

120 bpm

over 60s

95 bpm

2 ~ 3

4 ~ 5

105 bpm

115 bpm

• First, choose the most suitable preference (PRF) according to your

PWCmax value, from the table shown below.

2Isopower Training

• In this program the exercise intensity is set by the work rate: wattage. Se-

lect the target wattage from the table shown below, according to your

PWCmax. value provided by the Aerobic Power Measurement.

• The exercise time is initially set as 16 minutes, but you can revise it down

to minimum 3 minutes or up to 99 minutes.

PWC max

140 watt 175 watt 195 watt 240 watt 290 watt 310 watt 330 watt

Exercise Pattern(PRF)

Calorie Consumption

• If the selected wattage proves too hard for you, try again at the level 10

watts lower. When it becomes easy enough, raise the target by 10 watts.

75 kcal 95 kcal 110 kcal 120 kcal 130 kcal 140 kcal 155 kcal 200 kcal

• The calorie consumption provided above is based on the cadence of 60

rpm and the exercise time of 16 minutes. The calorie expenditure will vary

in proportion with the pedal cadence and the exercise time.

• Exercise for at least a 15 minute period. If possible a 20 ~ 30 minute period

is even better. Since warm up takes 3 minutes, set your actual exercise

time to "actual exercise time + 3 minutes".

PWC max

100 watt

120 watt

140 watt

160 watt

180 watt

200 watt

Target Wattage

40 watt

PWC max

220 watt

240 watt

260 watt

300 watt

350 watt

400 watt

Target Wattage

90 watt

5Manual Training

50 watt

95 watt

• In this program, the exercise intensity is set by the pedal resistance

(torque: kg·m.).

55 watt

105 watt

120 watt

140 watt

160 watt

65 watt

70 watt

• Exercise for at least a 15 minute period. If possible a 20 ~ 30 minute period

is even better. Since the warm up takes 3 minutes, set your exercise time to

"actual exercise time + 3 minutes".

80 watt

3Interval Training

Pedal Torque(kg·m)

PWC max

50 rpm 70 rpm 90 rpm

• In this program, select one of the 4 patterns (TLD 1 ~ 4) depending on

the power you want to improve, then set the exercise intensity by the

pedal resistance (torque: kg·m.).

120 watt

140 watt

160 watt

180 watt

200 watt

220 watt

0.9

1.1

1.2

1.4

1.6

1.7

0.7

0.8

0.9

1.0

1.1

1.2

0.5

0.6

0.7

0.8

0.9

1.0

240 watt

260 watt

280 watt

300 watt

350 watt

400 watt

1.9

2.0

2.1

2.3

2.7

3.1

1.3

1.5

1.6

1.7

1.9

2.2

1.1

1.2

1.3

1.5

1.7

• This program is for people with a long history of exercise.

• The following is a reference. Settings should match your physical fitness

level and purpose.

Download from Www.Somanuals.com. All Manuals Search And Download.

Aerobic power measurement (1)

• The buzzer sounds ten minutes later and the test result is dis-

played on the LCD, and also printed out. The program then

enters the 5 minute cool down phase and the ^COOLsymbol

lights up, however the LCD still displays the test result. Only

the calorie consumption data on LCD panel will be updated if

you keep pedaling.

Select the Aerobic Power

Measurement Program

Test Result Display,

Cool Down

• For program selection see the Starting up section page 18.

ml/kg·min

MOU

PFL

• Input your age, pulse limit, weight and sex. The initial display

prior to input is as in the drawing. The numeric for age is blink-

ing.

TEST

Note: When the upper pulse limit alarm is activated

Input Conditions

If the upper pulse limit alarm is activated while the elapsed

time is within 4 minutes, making the buzzer beep and drop-

ping the resistance to the minimum of 0.5 kg·m, the test

result is not displayed. If the upper pulse limit alarm is acti-

kcal

watt

PWC

Initial

Age

Value

Setting Range

10~ 99

kg·m

vated after the elapsed time exceeds 4 minutes, the result is

Pulse Limit

Weight

Sex

160 bpm

130 lb

Male

80~ 200 bpm

COOL

•

PLL

displayed based on the progress up to that point. In this

•

AGE

case the result is distinguished from normal results by add-

TEST

TIME

ing "=" to the printing data of the printer.

• The pitch sound to adjust your cadence at 60 rpm (rings every

half second) is set "ON".

• There is no graphic display yet in the LCD.

• Press the ^MODEbutton to change the blinking numeric.

• If the 5 minute cool down phase elapses or if you press

the ^ADVbutton, the buzzer sounds and the program ends.

• You can increase or decrease the blinking numeric by pressing

End Program

TIME

the

button.

• The LCD returns to the initial screen.

• If you are completely finishing the exercise, be sure to turn the

power off by the switch at the rear of the main body.

Sample print out

• After setting your conditions, adapt the earlobe pulse sensor

and press ^ADVbutton to start program.

Start Program

• Shows that the Aerobic Power Measurement program has

been performed.

• Date of execution

• After printing out the conditions the LCD changes as in the

drawing.

rpm

• Name: Put down your name in the blank.

• Sex : M = Male, F = Female

• Age

• The word "READY" will be displayed on LCD panel. Wait still

for one minute.

TEST

min:sec

• Weight (lb or kg)

• Upper limit pulse rate

• Elapsed time (minute): printed every 30 seconds

• Cadence

• After one minute has elapsed, the buzzer sounds and the pitch

sound begins. Then start pedaling according to the pitch sound.

watt

kg·m

• Work rate (watt)

• Pulse rate

• Pulse rate chart

Note: You can cancel the pitch sound by pressing

the

button. If the

symbol is on the LCD, the pitch

sound is ON, and if not pitch sound is OFF. Pressing the

pitch sound button toggles ON/OFF.

• One minute before exercise: shows the pulse rate at the rest.

TIME

• 1st stage

rpm

• The initial workload (pedal torque) is indicated in blinking dot

in the graphic section of the LCD. One dot along the horizontal

axis indicates 30 seconds, and one along the vertical axis 0.5

kg·m. At every 30 seconds, the row of dots will increase by one

towards the right of the graphic display, with the last row blink-

ing.

• 2nd stage

TEST

min:sec

• 3rd stage

watt

kg·m

• Calorie consumption

kg·m

• Maximum physical capacity (PWCmax): the greater, the

better.

• Maximum Oxygen uptake (MOU): the greater, the better.

• 5 rank physical fitness level

• At the 4th and 7th minutes the pedal torque will increase de-

pending on your pulse rate at that time. The increased torque of

2nd and 3rd stages will be indicated in dots time after time in the

graphic part.

TIME

Download from Www.Somanuals.com. All Manuals Search And Download.

Aerobic power measurement (2)

Physical Fitness Level (PFL)

Test Protocol

• There are five physical fitness levels: 1 ~ 5. These levels are relative

evaluations that compare your maximum oxygen uptake (MOU), esti-

mated by the aerobic power measurement program, with the values of

other people of the same age and sex (Physical Fitness Level Test Table).

• In the "Aerobic power measurement" program of the EC-1600, the

workload (pedal resistance: torque) for the subsequent stage is deter-

mined depending on your pulse rate at the previous stage. The workload

(pedal resistance: torque) will be increased along one of the routes illus-

trated below, depending on your pulse rate ™during the program.

• Ergociser™ EC-1600 stores the following physical fitness level test table,

which can be selected by the selector switch on the back panel of the con-

trol unit. (See page 9)

• The pulse rates specified below represent the protocol for a person of 20

years. For the people over 20, the borderline of pulse rate will be adjusted

by the age adjustment coefficient (K), which is obtained by the following

formula:

(ml/kg min)

[American Males]

[American Females]

Physical Fitness Level Test

Table by Maximum Oxygen

Uptake (MOU)

204–0.69 x Age

204–0.69 x 20

K =

ꢀ 5: Excellent

ꢀ 4: Good

ꢀ 3: Average

ꢀ 2: Fair

• For people over 60 years, the coefficient (K) is calculated as 60.

1.5 kg

Male

Pulse≥135

ꢀ 1: Poor

1.2 kg

1.8 kg

2.5 kg

1.8 kg

2.2 kg

2.6 kg

3.0 kg

3.3 kg

3.5 kg

Pulse≥110

90≤Pulse<110

Pulse<90

120≤Pulse<135

Pulse<120

(Age) 20s

30s

40s

50s

60s

(Age) 20s

30s

40s

50s

60s

Pulse≥135

Maximum Oxygen Uptake (MOU)

1.0 kg

120≤Pulse<135

Pulse<120

• MOU is widely used as an index for total physical endurance. MOU indicates the

amount of oxygen one can intake at the limit of their physical work capacity. In

the Ergociser™ EC-1600, MOU is calculated based on the maximum physical

work capacity (PWC max.) explained below, assuming that

Pulse≥135

1 litre of oxygen corresponds to 5.0 Kcal, and

the human body efficiency rate for a bicycle exercise is 23%

120≤Pulse<135

Pulse<120

Maximum Physical Work Capacity (PWC max.)

• In the Ergociser™ EC-1600 "Aerobic power measurement" program the

weight of the pedals are changed at 3 levels, and the pulse rate at the end

point of each level is measured. Based on the result, the relationship be-

tween the work rate (wattage) and the pulse rate is analyzed by linear

regression. Extend the regression line until reaching the maximum heart

rate (=204–0.69 x age) which is estimated by age. The work rate (wattage)

of this point becomes the maximum physical work capacity.

Female

1.1 kg

1.4 kg

1.5 kg

1.8 kg

2.5 kg

Pulse≥123

Pulse<123

Pulse≥123

Pulse<123

Pulse≥123

Pulse<123

0.8 kg

1.0 kg

1.5 kg

Pulse≥115

95≤Pulse<115

Pulse<95

0.5 kg

• PWC max. safely estimates how much exercise is possible at the limit of

physical work capacity, that is, at maximum heart rate without perform-

ing actual exercise.

(bpm)

180

Maximum Heart Rate

140

Measurement

Estimate

120

Remark: The load change for males over 50 years of age is the same as

for females.

When the age is less than 20, the load changes as if the age were 20.

Heart Rate

100

125

150 (watt)

Work Rate

Maximum Physical Work Capacity

Download from Www.Somanuals.com. All Manuals Search And Download.

Automatic training

Select the Automatic

Training Program

Exercise Maintaining the

Target Pulse Rate

• After the ^WARMsymbol has gone out, during exercise every time

the pulse rate digresses ± 3 bpm from the target, the load changes

0.1 kg·m, keeping your pulse rate close to the target pulse rate.

• For program selection see the Starting up section page 18.

rpm

Note: When the pulse rate is "0" (when the earlobe sensor is

removed) or when the pedal cadence is "0" (when not exer-

cising) the pedal resistance does not change.

min:sec

AUTO

• Input age, pulse limit, exercise time and the target pulse rate.

The initial display before input is as in the drawing, with the nu-

meric for age blinking.

Input Conditions

Remark 1: You can increase or decrease the pedal resistance

watt

by pressing the

buttons.

kg•m

Remark 2: The graphic section will display the torque pattern for

maximum 16 minutes. At the end of 16 minutes period, torque

pattern once disappear and the actual torque at that moment

will be displayed flashing at the left end of the section.

Initial Value Setting Range

kg•m

Age

Pulse Limit

Exercise Time

10~ 99

PLL

160 bpm

20 min

Target Pulse Rate 120 bpm

80~ 200 bpm

0~ 99 min

60~ 180 bpm

AGE

min:sec

TIME

AUTO

TPL

• The pitch sound to adjust your cadence at 60 rpm (rings every

bpm

half second) is set "OFF".

• There is no graphic display yet in the LCD.

Finish Exercise

Cool Down

• The buzzer sounds at the specified time. If you press the ^ADV

button, the program enters a 5 minute cool down phase and

the ^COOLsymbol lights up, then the pedal resistance becomes

the minimum of 0.5 kg·m.

• You can increase or decrease the blinking numeric by pressing

the

buttons.

TIME

rpm

• Press the ^MODEbutton to change the blinking numeric.

min:sec

Note: Even if the buzzer sounds the program does not enter

the cool down phase unless you press the ^ADVbutton.

AUTO

watt

• The LCD still displays the same exercise data.

kg•m

• After setting your conditions, adapt the earlobe pulse sensor

and depress ^ADVbutton to start program.

Start Program

kg•m

COOL

TIME

Start / Warm Up

• After printing out the conditions, the LCD changes as in the

drawing.

• If the 5 minute cool down phase has elapsed or if you press the

End Program

ADV

button, the buzzer sounds and the program ends. The

• The initial workload (pedal torque) is indicated in blinking dot

in the graphic section of the LCD. One dot along the horizontal

axis indicates 30 seconds, and one along the vertical axis 0.5

kg·m. At every 30 seconds, the row of dots will increase by one

towards the right of the graphic section, with the last row blink-

ing.

calorie consumption is printed out, and the LCD returns to the

initial screen.

rpm

• If you are completely finishing the exercise, be sure to switch off

the main body.

min:sec

AUTO

watt

Sample print out

• The pedal resistance increases gradually, so that the pulse rate

kg•m

goes up toward the target pulse rate.

• Shows that the Auto training program has been preformed.

• Target pulse rate

kg•m

• The ^WARMsymbol remains until your pulse rate gets close to

the target pulse rate.

WARM

• Upper limit pulse rate

TIME

• Calorie consumption

Download from Www.Somanuals.com. All Manuals Search And Download.

Isopower (constant load) training

• After the ^WARMsymbol goes out, the pedal resistance (torque

kg·m) increases or decreases according to the pedal cadence.

During exercise the pedal resistance (torque: kg·m) changes in

0.1 kg·m units to maintain the set value for wattage.

Select the Isopower

Training Program

Exercise at Constant

Wattage

• For program selection see the Starting Up section page 18.

rpm

• Target wattage can be changed during exercise by pressing

either

button. The new target wattage will be dis-

min:sec

played for 2 seconds in place of the current wattage.

• Input age, pulse limit, exercise time and set wattage. The initial

display prior to input is as in the drawing. The numeric for age is

blinking.

Input Conditions

CONST

Note: For calculation purposes, pedal cadence under 40 rpm is

regarded as 40 rpm, and pedal cadence over 100 rpm is re-

garded as 100 rpm.

watt

Initial Value Setting Range

kg•m

Age

10~ 99

kg•m

PLL

Remarks: The graphic section will display the torque pattern for

maximum 16 minutes. At the end of the 16 minutes period, the

torque pattern once disappear and the actual torque at that mo-

ment will be displayed flashing at the left end of the section.

AGE

Pulse Limit

Exercise Time

Set Wattage

160 bpm

20 min

60 watts

80~ 200 bpm

0~ 99 min

25~ 200 watts

min:sec

CONST

TIME

watt

• The pitch sound to adjust your cadence at 60 rpm (rings every

TLD

half second) is set "OFF".

• There is no graphic display yet in the LCD.

• You can increase or decrease the blinking numeric by pressing

Finish Exercise

Cool Down

• The buzzer sounds at the specified time.

the

buttons.

TIME

ADV

• If you press the

button, the program enters a 5 minute

• Press the ^MODEbutton to change the blinking numeric.

cool down phase and the ^COOLsymbol lights up. Then the

pedal resistance becomes the minimum of 0.5 kg·m.

rpm

min:sec

Note: Even if the buzzer sounds, the program does not enter

the cool down phase unless you press the

CONST

ADV

button.

• After setting your conditions, adapt the earlobe pulse sensor

and depress ^ADVbutton to start program.

watt

Start Program

kg•m

• The LCD still displays the same exercise data.

kg•m

COOL

TIME

• After printing out the conditions, the LCD changes as in the

drawing.

Start / Warm Up

• The initial workload (pedal torque) is indicated in blinking dot in

the graphic section of the LCD. One dot along the horizontal axis

indicates 30 seconds, and one along the vertical axis 0.5 kg·m. At

every 30 seconds, the row of dots will increase by one towards the

right of the graphic section, with the last row blinking.

• If the 5 minute cool down phase has elapsed or if you press the

button, the buzzer sounds and the program ends. The

End Program

ADV

rpm

calorie consumption is printed out, and the LCD returns to the

initial screen.

min:sec

• If you are completely finishing the exercise, be sure to switch off

the unit.

CONST

• For the 3 minutes warming up time after starting exercise,

pedal resistance will gradually increase and ^WARMmark ap-

pears on the panel.

watt

kg•m

Sample print out

kg•m

WARM

Note: During the warm up, the pedal resistance is increased so as to

reach the set wattage in 3 minutes provided you pedal at 50 rpm. If

you pedal faster than 50 rpm and reach the set wattage earlier than

3 minutes, the warm up is finished at that moment.

• Shows that the Isopower (constant load)

training program has been performed.

• Set wattage

TIME

• Upper limit pulse rate

Remark: If you first press the ^MODEbutton, and holding it down

press the ^ADVbutton to start the program, instead of just press-

ing the ^ADVbutton, you can skip the warm up phase and start

the exercise at the preset wattage from the scratch.

• Calorie consumption

Download from Www.Somanuals.com. All Manuals Search And Download.

Interval training

Select Interval Training

• For program selection see the Starting up section page 18.

Exercise

• After the ^WARMsymbol goes out, the pedal resistance (torque

kg·m.) change periodically according to the exercise pattern.

1 _Program

• During the exercise period (higher load portion of interval), you

should pedal with your greatest effort, then you should pedal

slower and lighter during relief period (lower load portion).

rpm

min:sec

INTVL

• Input age, pulse limit, exercise time, set torque and the exercise

pattern.

• In the TLD-3 stamina training program, it is advisable to pedal

fast enough in the exercise period to keep your pulse rate at

60~80% of the maximum pulse rate for your age. (Refer to page

20~21)

Input Conditions

watt

• The initial display prior to input is as in the drawing. The nu-

meric for age is blinking.

kg•m

Initial Value

Setting Range

10 ~ 99

Age

PLL

TIME

Pulse Limit

Exercise Time

160 bpm

15 min

80 ~ 200 bpm

0 ~ 99 min

AGE

INTVL

min:sec

Target Torque Value 2.0 kg·m 0.5 ~ 4.0 kg·m

Exercise pattern 1 ~

TTQ

End Exercise

Cool Down

TLD

• The pitch sound to adjust your cadence at 60 rpm (rings every

half second) is set "OFF".

kg•m

• The buzzer sounds at the specified time.

kg•m

• If you press the ^ADVbutton, the program enters a 5 minute

cool down phase and the ^COOLsymbol lights, then the pedal

resistance becomes the minimum of 0.5 kg·m.

• The load pattern is displayed in the graphic section according to

the selected exercise pattern and set torque value.

rpm

TIME

• You can increase or decrease the blinking numeric by pressing

min:sec

INTVL

Note: Even if the buzzer sounds, the program does not enter

the cool down phase unless you press the ^ADVbutton.

the

buttons.

watt

• Press the ^MODEbutton to change the blinking numeric.

kg•m

• The LCD still displays the same exercise data.

kg•m

COOL

• After setting your conditions, adapt the earlobe pulse sensor

and depress ^ADVbutton to start program.

TIME

Start Program

• If 5 minutes of cool down elapses or if you press the ^ADV

button, the buzzer sounds and the program ends.

End Program

• Calorie consumption is printed out, and the LCD returns to the

initial screen.

Start / Warm Up

• After printing out the conditions, the LCD changes as in the

drawing.

• If you are completely finishing the exercise, be sure to switch

off the main body.

• Load pattern is displayed in the graphic section, and the dot at

the far left is blinking. 1 dot in the horizontal axis indicates 15

seconds; 1 dot in the vertical axis indicates 0.5 kg·m.

rpm

Sample print out

Exercise Pattern

min:sec

• When 15 seconds is over, the dot to the immediate right will

start blinking. With the lapse of time, the blinking row will move

to the right. The position of the blinking dots determines where

you are in the interval pattern.

TLD-1 dash strength training

INTVL

15 seconds exercise

45 seconds relief

• Shows that the Interval training

program has been performed.

• Set torque value

watt

TLD-2 speed training

30 seconds exercise

60 seconds relief

kg•m

• Exercise pattern

kg•m

• During the first 3 minutes of warm up, the pedal resistance

gradually increases and the ^WARMsymbol lights.

WARM

• Upper limit pulse rate

TLD-3 stamina training

60 seconds exercise

30 seconds relief

Note: After three minutes, the pedal resistance (torque value:

TIME

kg·m) reaches about a half of the set torque value.

TLD-4 customized pattern

(See page 40.)

• Calorie consumption

Download from Www.Somanuals.com. All Manuals Search And Download.

Hill profile training

Select the Hill Profile

Training Program

• The buzzer sounds at the specified time. The program ends and

the calorie consumption is printed out.

• For program selection see the Starting up section page 18.

End Program

• The LCD returns to the initial screen.

rpm

Note 1:

There is no cool down phase if you finish Hill pro-

• Input pulse limit, exercise time, and the exercise pattern. The

initial display prior to input is as in the drawing. The numeric

for age is blinking.

file program at the end of the specified exercise time.

min:sec

Input Conditions

HILL

Note 2:

If you press the ^ADVbutton during exercise, the

program enters a 5 minute cool down phase and the pedal

resistance becomes the minimum of 0.5 kg·m. The LCD still

displays the same exercise data. The program ends if the 5

watt

Initial Value Setting Range

kg•m

Age

10 ~ 99

kg•m

Pulse Limit

Exercise Time

Exercise pattern

160 bpm

16 min

80 ~ 200 bpm

16 ~ 99 min

minute cool down phase elapses or if the ^ADV

pressed.

button is

PLL

AGE

1 ~

min:sec

TIME

HILL

• The pitch sound to adjust your cadence at 60 rpm (rings every

half second) is set "OFF".

PRF

• The whole hill pattern of the selected number is displayed in the

kg•m

graphic section.

Sample print out

Exercise Pattern

• You can increase or decrease the blinking numeric by pressing

PRF-1 the Apennines

the

buttons.

maximum torque 1.7 kg·m

TIME

• Shows that the Hill

profile training program

has been performed.

• Press the ^MODEbutton to change the blinking numeric.

PRF-2 the Apparachian

maximum torque 2.2 kg·m

• Exercise pattern

• Upper limit pulse rate

PRF-3 the Cascades

maximum torque 2.5 kg·m

• After setting your conditions, adapt the earlobe pulse sensor

and depress ^ADVbutton to start program.

Start Program

• After printing out the conditions, the LCD changes as in the

drawing.

PRF-4 the Pyrenees

maximum torque 3.0 kg·m

• The hill pattern is shown in the graphic section, and the dot at the

far left is blinking. One dot along the vertical axis indicates 0.5

kg·m, while one along the horizontal axis differs in proportion

with the preset exercise time. If it is 16 minutes for example, one

dot stands for 30 seconds, and if 32 minutes one is 1 minute.

rpm

PRF-5 Mount Fuji

maximum torque 3.7 kg·m

min:sec

• Calorie consumption

HILL

watt

PRF-6 the Rockies

maximum torque 3.5 kg·m

• When the time represented by one dot is over, the dot to the

immediate right will start blinking. With the lapse of time, the

blinking row will move to the right. The position of the blinking

dots determines where you are in the hill pattern.

kg•m

PRF-7 the Alps

maximum torque 3.7 kg·m

Note: There is no warm up phase in the "Hill profile training"

program.

TIME

PRF-8 the Himalayas

maximum torque 4.0 kg·m

PRF-9 customized pattern

• The pedal resistance (torque, kg·m) changes periodically ac-

cording to the exercise pattern.

(See page 40.)

Exercise

Remarks: In this program, you can change the pedal resis-

tance temporarily by depressing either

ton, whenever desired.

but-

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual training

Select the Manual Training

Program

• Exercise at the set pedal resistance (torque, kg·m).

• For program selection see the Starting up section page 18.

Exercise

Note: In this program, you can increase or decrease the pedal resis-

tance by pressing the

buttons whenever desired.

rpm

Remark 1: In this program only, even if the upper pulse limit

alarm is activated and the pedal torque drops down to 0.5

kg·m, the program does not enter the cooling down phase,

and you can carry on the preset workout by increasing pedal

min:sec

• Input age, pulse limit, exercise time, and the setting torque

value. The initial display prior to input is as in the drawing. The

numeric for age is blinking.

Input Conditions

MANUAL

watt

torque with

button.

kg•m

Initial Value Setting Range

Remark 2: The graphic section will display the torque pattern for

maximum 16 minutes. At the end of the 16 minutes period, the

torque pattern once disappear and the actual torque at that mo-

ment will be displayed flashing at the left end of the section.

kg•m

Age

10 ~ 99

PLL

AGE

Pulse Limit

Exercise Time

160 bpm

20 min

80 ~ 200 bpm

0 ~ 99 min

min:sec

TIME

Set Torque Value 1.0 kg·m 0.5 ~ 4.0 kg·m

MANUAL

TTQ

• The pitch sound to adjust your cadence at 60 rpm (rings every

half second) is set "OFF".

kg•m

• There is no graphic display yet in the LCD.

Finish Exercise

Cool Down

• The buzzer sounds at the specified time.

• You can increase or decrease the blinking numeric by pressing

ADV

• If you press the

button, the program enters a 5 minute

the

buttons.

TIME

cool down phase and the ^COOLsymbol lights up, then the

pedal resistance becomes the minimum of 0.5 kg·m.

• Press the ^MODEbutton to change the blinking numeric.

rpm

Note: Even if the buzzer sounds, the program does not enter

min:sec

ADV

the cool down phase unless you press the

button.

MANUAL

watt

ADV

• Press the

button to start the program after you set the

• The LCD still displays the same exercise data.

Start Program

conditions.

kg•m

COOL

TIME

• After printing out the conditions, the LCD changes as in the

drawing.

Start / Warm Up

• The initial workload (pedal torque) is indicated in blinking dot in

the graphic section of the LCD. One dot along the horizontal axis

indicates 30 seconds, and one along the vertical axis 0.5 kg·m. At

every 30 seconds, the row of dots will increase by one towards the

right of the graphic section, with the last row blinking.

• If the 5 minute cool down phase elapses or if you press the

button, the buzzer sounds, the program ends and the

End Program

ADV

calorie consumption is printed out.

rpm

• The LCD returns to the initial screen.

• After starting exercise, during the 3 minute warm up, the pedal

resistance gradually increases and the ^WARMsymbol is shown.

min:sec

Note: During the warm up the pedal resistance increases so

that it reached the set torque value in 3 minutes. If you have

increased the torque value to more than the set torque

MANUAL

Sample print out

watt

• Shows that the Manual training

program has been performed.

• Torque value you set initially

kg•m

value by pressing the

ends at that point.

buttons, the warm up phase

kg•m

WARM

• Upper limit pulse rate

Remark: If you first press the ^MODEbutton, and holding it

down press the ^ADVbutton to start the program, instead

of just pressing the ^ADVbutton, you can skip the warm

up phase and start the exercise at the preset pedal torque

from the scratch.

TIME

• Calorie consumption

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting your own training pattern

You can create your own training pattern as desired, for

both interval training and hill profile training, and can

keep them in memory for future use. Enjoy your exercise

under your original training program on this model.

It is 1 pattern each in the Interval training (TLD-4) and

Hill profile training (PRF-9), that you can write in your

own customized pattern.

Input new training pattern

• Using

button, you can change the pedal resis-

tance (workload level) of the blinking row.

• Pedal resistance will be displayed in both numerical value and

dot pattern. Set your preferred torque value in the range from

0.5 kg·m to the maximum of 4.0 kg·m.

PLL

AGE

• Having set the torque value for the first row, press ^MODEbut-

ton and the next right row starts blinking. Repeat the same pro-

cedure until you finalize the total pattern ending up with the

32nd row.

min:sec

HILL

target torque

TTQ

Row No.

kg•m

Procedure for writing a new pattern is the same for both interval training

and hill profile training. The following is an example of writing in a new

pattern on the hill profile training.

kg•m

Remarks: Pressing ^MODEbutton when the 32nd column is

blinking, the blinking system restarts from the first column

towards the right for your modification of load pattern wher-

TIME

ever necessary by using

button.

Select the Hill Profile

• Press ^MODEbutton until "HILL" (or INTVL) flashes, and

press ^ADVbutton to enter the program.

Training Program

pattern

• After writing in the whole load pattern, press ^ADVbutton.

Your new training program is registered in memory, and the

LCD will turn to the condition input screen.

Select the customized

• Press ^MODEbutton until the PRF number blinks.

2 _pattern

• Your own training pattern will be displayed on the screen sim-

ply by selecting exercise pattern PRF-9 (TLD-4 in case of inter-

val training) hereafter.

• Using

button, let the number 9 (TLD-4 in case of

min:sec

interval training) appear on the screen.

HILL

PRF

kg•m

TIME

Change display panel

into write-in phase

• Hold down the ^MODEbutton about 2 seconds. A buzzer beeps

and the LCD screen will enter the pattern write-in mode. The

far left dot in the graphic section is blinking.

Customized pattern (TLD-4) of interval training

PLL

AGE

• The customized pattern created in 8 minutes time frame will be

repeated during the target exercise time without warm up

phase, unlike other training patterns (TLD-1~TLD-3).

min:sec

INTVL

HILL

TTQ

Row No.

target torque

TLD

• Since different torque values may be set in each time frame, the

"Target Torque" cannot be determined in a single value. There-

fore, neither TTQ display appears on the condition input screen,

nor will the printer print out the indication of set torque.

kg•m

customized pattern

TIME

Download from Www.Somanuals.com. All Manuals Search And Download.

How to make a data card

EXAMPLES OF DATA CARD PROGRAMMING

MANU

HILL

MANU

HILL

MANU

HILL

If you record your training conditions to this "Data

Card", you can set the conditions merely by inserting the

card into the card inlet of the control unit. You can start a

INTVL

program just by inserting the card and pressing

CONST

ADV

the

button, saving all the button operation process.

AUTO

TEST

AUTO

TEST

AUTO

TEST

To record your conditions to the

data card, scratch off the appropri-

ate silver part on the back of the

card with a coin etc. This removal

allows the photo scanner in the con-

trol unit to detect the position of the

exposed part. Now let's make your

"Data Card."

MANU

HILL

For Automatic Training

For Interval Training

Age: 32 years Time: 16 minutes

Pattern: TLD 1 Maximum Torque: 3.5 kg·m Set Torque: 1.5 kg/m

For Manual Training

Age: 28 years Time: 35 minutes

Target Pulse Rate: 130 bpm

Age: 57 years Time: 40 minutes

MANU

HILL

MANU

HILL

MANU

HILL

INTVL

CONST

Note: One Data Card is neces-

sary for each of the desired

co n d it io n s. Y o u ca n n o t

specify two or more condi-

tions on one card.

AUTO

TEST

INTVL

CONST

AUTO

TEST

AUTO

TEST

AUTO

TEST

Memo Space

Exercise Target

Exercise Pattern

Age

Exercise Time (minute)

For Isopower Training

For Hill Profile Training

For Aerobic Power Measurement

Age: 35 years Weight: 56 kgs.

Sex: Female

Age: 57 years Time: 20 minutes

Target Wattage: 65 watts

Age: 45 years Time: 32 minutes

Pattern: 3 (The Cascades)

4 Specify Exercise Pattern

1 Specify Program

2 Specify Age

3 Specify Exercise Time

5 Specify Training Target

• Specify the exercise pattern in

"F" when the "Interval training"

or "Hill profile training" is se-

lected.

• Specify the program in "A".

• Specify your age in "B" and "C".

• "B" indicates the first digit of

your age, "C" indicates the sec- • "D" indicates the first digit of

ond.

Example: Age 35 years

Enter "3" in "B" column

Enter "5" in "C" column

• Specify your exercise time in

"D" and "E".

• Specify the training target in "G",

"H" and "I".

4) Hill Profile Training

Whatever you specify in "G", "H",

"I" is invalid.

1) Automatic Training

the exercise time, "E" indicates

the second.

Specify the target pulse rate. "G" in-

dicates the first digit of the value,

"H" indicates the second and "I" in-

dicates the third digit.

5) Manual Training

• What you specify in "F" is invalid

for other exercise programs.

Specify the set torque value. "H" in-

dicates the first digit of the value,

"I" indicates the first decimal place.

Whatever you may set in "G" is in-

valid.

• For Interval Training, choose one

of 1 ~ 4.

CAUTIONS ON HANDLING THE DATA CARD

2) Isopower Training

Scratch by a coin etc.

• For Hill Profile Training, choose

one of 1 ~ 9.

• Treat the card with care. Do not bend or damp the card.

• Scratch only the necessary part of the silver ink. Otherwise the sensor

will not read out the data.

• Wipe the residue of the scratched silver ink off the card before inserting

the card into the control unit.

• The blank space on the card can be utilized as memo space to enter the

programmed data, user's name etc.

• If you have scratched incorrect data, use "white out" to cover the hole.

If the light doesn't go through the hole that you have covered up, the

card can be used normally.

Specify the set wattage. "G" indi-

cates the first digit of the wattage,

"H" indicates the second, and "I"

indicates the third digit.

COIN

Note 1: When you execute the

" A erobic Power Measure-

ment" with the card, specify

your weight in "D","E" and

"F".

"D" is the third digit, "E" the

second and "F" the first digit.

Your sex is specified in "G".

" 0" indicates female, " 1"

male.

3) Interval Training

Specify the set torque Value. "H"

indicates the first digit of the value,

"I" indicates the first decimal place.

If you select TLD-4, you don't have

to specify any figure here. Whatever

you may set in "G" is invalid.

White-out

Note: If "ERROR" appears on the LCD when you insert the card,

check whether any incorrect or unnecessary point has been

scratched out.

Download from Www.Somanuals.com. All Manuals Search And Download.

1 External computer control via an RS232C

terminal

2 Using chestbelt heart rate sensor

3 Setting the date

4 Printing mechanism

5 Troubleshooting and handling care

6 Warranty service and optional parts

7 Specifications

Download from Www.Somanuals.com. All Manuals Search And Download.

External computer control via an RS232C terminal

3 digit numeric Pulse rate

3 digit numeric Pedal cadence

1 digit numeric Aerobic power measurement result: PFL

External computer control via an RS232C

terminal

2 digit numeric

Aerobic power measurement result: MOU

If you connect the optional "RS232C Communication Kit," the Ergo-

ciser™ can communicate with an external computer.

3 digit numeric Aerobic power measurement result: PWC max.

3 digit numeric Set wattage (Isopower training)

Specifically, you can write a program with an external computer in

Basic or in another computer language, and operate the Ergociser™

EC-1600 according to the written procedure. Any instructions input

by the buttons on the EC-1600 control unit can be input from the ex-

ternal computer, and the EC-1600 sends data to an external computer

every second. Since command signals are in ASCII character code,

any computer that generates these codes can be used, receiving and

transmitting via the RS232C terminal.

2 digit numeric

CR code

Lowest 2 digits of addition value of data address 2 ~ 29

Hexadecimal 0DH

Note: "0" is displayed in each digit for the 3 types of aerobic power

measurement results, until the program is completed.

Externally Controlling the EC-1600

1) During Setting Exercise Conditions

Transmission Format

When exercise conditions are being set, you can send data in a "char-

acter code + numeric code + CR code" format (shown in example

below) from an external computer, setting your exercise conditions.

Communication speed (baud rate)

Data bit length

Stop bit

Parity check

XON / XOFF control

SI/SO control

2400

8 bit

1 bit

none

Example) "K6CR" : Selects Auto Training

Character Code

Function

Age (up to 2 digits)

Pulse limit value (up to 3 digits)

Target time (up to 2 digits)

Weight (up to 3 digits)

Set torque x 10 (2 digits)

Exercise pattern (Hill Profile Training)

Sex (male: "1", female: "0")

Target pulse rate (up to 3 digits)

Set wattage (up to 3 digits)

Exercise pattern (Interval Training)

Exercise program

Contents of DataTransmission from the EC-1600

The EC-1600 outputs display data in character code, continuously

when you set exercise conditions and once per second when you are

exercising. Since the contents of the LCD differs according to setting

exercise conditions and during exercise, the content of data output

also differs.

1) Setting Exercise Conditions

Address Data

Function

1: Aerobic Power Measurement

2: Manual Training

3: Hill Profile Training

4: Interval Training

5: Isopower Training

A code

Hexadecimal 41H

3 digit numeric Set wattage (Isopower Training)

1 digit numeric Exercise pattern (Interval Training)

3 digit numeric Target pulse rate (Auto Training)

1 digit numeric Sex (male:"1", female:"0")

1 digit numeric Exercise pattern (Hill Profile Training)

2 digit numeric Set torque x 10

3 digit numeric Weight (Aerobic Power Measurement)

2 digit numeric Target time (minutes)

3 digit numeric Pulse limit value

6: Auto Training

Reset torque during exercise x 10 (2 digits)

2) During Exercise

By using the following character codes for button operation, you can

externally control the program during exercise.

2 digit numeric Age

CR code

Example) Sending "i CR" during Manual Training

Hexadecimal 0DH

→ increases pedal resistance (torque) 0.1 kg·m

2) During Exercise

Character Code

Function

Address Data

Function

RESET button

ADV button

+ 1 button

B code

Hexadecimal 42H

4 digit numeric Elapsed time

2 digits = "minute"

2 digits = "second"

– 1 button

4 digit numeric Calorie consumption

3 digit numeric Wattage

2 digit numeric Pedal torque x 10

See the instruction manual for the optional "RS232C Communication

Kit" for details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using chestbelt heart rate sensor

Setting the date

Wireless chestbelt sensor picks up your heart rate

Displaying the Date

• W h i l e h o l d i n g d o w n

the ^MODEbutton, hit the RE-

SET button once, and the date

In place of the earlobe pulse sensor, the EC-1600 can also receive

your pulse signal transmitted from a particular type of wireless

chestbelt sensor. The "Wireless Pulse Sensor Kit" (an optional item)

is recommended for the customers who may feel inconvenience in

picking up the pulse rate from the earlobe.

and time are displayed. (as displayed in the lower column)

Setting the Date

• By each press of the ^MODEbutton, different numerics will blink in

EC- 1

RESET

CADENCE

PROGRAM

NAME

PEDAL

TORQUE

Function of wireless chestbelt sensor

TIME

The wireless chestbelt sensor is a simplified and compact electrocar-

diograph as widely used in hospitals on the same principle. At hospi-

tals, electrodes are attached to several parts of the body, and a cardio-

gram is determined on the basis of potential differences among those

electrodes. The chestbelt sensor picks up the heart rate more simply

through potential difference between two electrodes built-in there

and in contact with the body.

Interval Training Preference

TLD 1. 15 sec. work 45 sec. relief

Dash (Sprint Power) Training

TLD 2. 30 sec. work 60 sec. relief

Speed (Anaerobic Power) Training

TLD 3. 60 sec. work 30 sec. relief

Stamina (Aerobic Power) Training

MODE

ADV

TLD.4. Make

training pattern as desired.

Hill Profile Preference

Intensity of program is adjusted

according to PRF Number.

PRF

is least intense.

is most intense.

PRF 9. Design

profile as desired.

The pulse data are transmitted to the control unit by radio wave, thus

eliminating inconveniences of handling the sensor cable and offering

concentrated intense training.

the sequence of minute-

hour-date-month-year.

• Set the date and time by pressing the

or decrease the blinking numeric.

buttons to increase

The "Wireless Heart Rate Sensor Kit" consists of a chestbelt sensor

unit (transmitter) and a receiving circuitry to be mounted inside of the

control unit.

• Once the minute is set, the clock starts working. So set at the actual

minutes without considering the time for setting other data.

Finishing the Setting

Attaching the chestbelt sensor

The chestbelt sensor should be put around your chest with two elec-

trodes in contact with your body at the center.

year

For further information, please refer to the Manual enclosed in the

"Wireless Heart Rate Sensor Kit" (an optional item).

month

hour

date

minute

TIME

Chestbelt heart rate sensor adapted in

position

• When the setting is over, press

Direct contact to lower chest skin is ideal in use.

the ^ADVbutton. The LCD returns to the initial display (screen to

select a program).

• The date is printed out at the beginning of a printer printout.

Download from Www.Somanuals.com. All Manuals Search And Download.

Printing mechanism

6. Holding the edge of the thermal paper coming out of the paper

guide, pull it out and pass it under the printer cover.

Close the printer cover, and draw the paper until the paper edge

entirely comes out of the printer cover.

Pull

Inserting printer paper

1. Pull out the paper case at the bottom of the control unit and detach

it.

paper guide

paper case

7. Insert the paper case completely into the bottom of the control unit.

Then pull the thermal paper again to remove the paper sag in the

paper case.

printer cover

This completes setting the thermal paper.

You can cut the thermal paper with the printer cover closed.

2. Cut the edge of the thermal paper to a point with a scissors (as illus-

trated).

What to do when printer paper gets jammed

cut

1. Lift up the paper guide on the front panel of the control unit.

printer cover

thermal paper

paper guide

3. Insert the paper roller into the paper roll, and place the roll in the

case in the correct position and direction as illustrated.

Note: The printer will not print out data on the reverse side of the

paper. Check the proper direction before inserting.

thermal paper

face

paper

roller

2. Use tweezers to remove the jammed paper.

4. Insert the paper case halfway into the bottom of the control unit (as

illustrated below).

Insert

paper inlet

5. Then raise the printer cover and insert the pointed edge of thermal

paper into the paper inlet of the control unit.

Caution on printer operation

• Do not drive the printer without the thermal paper on it. If the ther-

mal paper is unavailable, press the printer

button and confirm

that the printer symbol on the LCD is not lit up before use.

• Please use the specified Cateye thermal paper (part #7226502) only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting and handling care

Problem

Item to check

Countermeasure

Troubleshooting

The evaluation of fitness level Is the weight unit correct?

seems incorrect.

Set the weight unit correctly. (see

page 8)

Problems noted in the following chart are not disorders. Prior to seeking

repair, read the contents of the entire chart first.

Did you select the correct fitness

level evaluation table?

Check the selector switch on the

back panel of the control unit. (see

page 8~9)

Problem

Item to check

Countermeasure

Display does not appear.

Is the power supply connected?

Connect the AC adaptor correctly.

(see page 14)

The program is suspended half- Isn't the upper pulse limit alarm Input your age correctly to prevent

Is the power switch on?

Turn the power on.

way.

ringing due to the excess of your the alarm from ringing unduly.

pulse rate during the exercise?

Isn't the cable of the AC Adapter Replace the AC Adapter if its inte-

damaged?

rior circuit or the cable is dam-

aged.

Buzzer keeps sounding.

The pitch sound doesn't ring.

Isn't the pulse limit setting too low

due to an incorrect age input?

Printer does not work.

Didn't you select "not to use" the Set the select switch No.4 to OFF.

printer with the selector switch on (see page 8)

the back panel of the control unit?

Is the

LCD?

symbol shown on the Press the

button on the control

symbol show up.

unit to let the

Check if sensor plug is completely Unit does not give pitch sound if

connected.

plug is out of jack.

Is the

LCD?

symbol shown on the Press the

button on the Con-

symbol

trol U nit to let the

Clattering noise is heard with the Are the pedals firmly attached to Attach the pedals firmly.

pedal rotation.

show up. But if the select switch

No.4 on the back of the control

the crank? If not, noise may be pro-

duced.

unit is ON, the

symbol doesn't

appear even if you press the but-

ton.

Isn't the paper jammed?

Did you set the date?

Remove the jammed paper. (see

page 51)

Date memory is incorrect.

Set the date correctly (page 49)

Are the backup batteries installed? Load the backup batteries. (see

If not, the date memory is lost each page 8)

time you turn off the power.

Handling

For longer use of the Ergociser™ EC-1600, observe the following

precautions.

Isn't the

LCD?

symbol shown on the Replace the backup batteries, be-

cause they have worn out. (see

page 8)

• Do not disassemble the main and control units. In case of prob-

lems contact your dealer where the unit was purchased.

• Avoid using the Ergociser™ EC-1600 in a high temperatures or in

high humidity. Also, do not splash the unit with water.

ERROR or irregular display ap- Isn't the data card reversed?

pears when you insert the data

card.

Hold the card yellow arrow side

up, and insert to the direction of

arrow.

• Handle the pulse sensor carefully. If strongly pulled out the cable

may become disconnected.

D idn' t you insert the card too Insert the card slowly.

quickly?

Didn't you specify two or more pro- Refer to P.42~43 and specify the

grams, or open unnecessary holes?

program and conditions correctly.

• When the EC-1600 is not in use, shut the power switch OFF and

disconnect the power cord from the outlet.

• Do not wipe the main unit with organic solvents such as thinner,

kerosine, gasoline and alcohol. When dirty, wipe the unit with a

cloth soaked in a neutral detergent, then wipe well with a dry

cloth.

The pulse rate is not displayed, re- Is the pulse sensor attached cor- Insert the sensor plug securely into

maining "0".

rectly to your earlobe?

the sensor jack, and check the

pulse sensor function according to

page 11. If the sensor cable proves

to be broken, replace the pulse

sensor (part #1655210).

Is the sensor plug completely in-

serted into the sensor jack?

• Do not place the EC-1600 in direct sun light.

The pulse rate increases abnor- Is the pulse sensor correctly at- Attach the sensor correctly to your

mally.

tached to your earlobe?

earlobe and take care not to swing

the sensor or sensor cable during

the exercise. If the sensor cable

proves to be damaged, replace the

whole pulse sensor with a new one.

Isn't the sensor cable damaged?

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty service and parts

Specifications

Item

Specifications

Home AC Power (Use specified AC adapter only.)

Warranty service

Power source

• Cat Eye Co., Ltd. guarantees that the Cateye Ergociser™ Model

EC-1600 is free from material defects and malfunctions under cor-

rect and normal use for three (3) years from the date of purchase.

In case there should be defects or malfunctions, Cat Eye will repair

or replace the unit or parts, according to the terms and conditions

mentioned in the separate Warranty Card.

Power consumption Max. approx. 15 W

Loading system

Eddy current system

Speed increasing

mechanism

2-step speed increase by chain and timing belt

Control system

Display system

Display functions

8-bit microcomputer control system

Liquid crystal display

• If repair service is required, contact your dealer where the unit was

purchased.

Function

Display range

Pulse rate

50 ~ 199 bpm

• The warranty covers only the main unit and the control unit. Acces-

sories such as the pulse sensor or the AC adaptor are not covered.

Pedal cadence

Exercise time

20 ~ 199 rpm

00min. 00sec. ~ 99min. 59sec.

Calorie consumption 0 ~ 999 kcal (Estimated value)

Load torque 0.5 ~ 4.0 kg·m

Work rate (wattage) 0 ~ 400 watts

Printing system

Data input system

Pulse sensor

Thermal printer, Thermal paper (57mm x 25m roll)

Data card (Use specified cards only) and buttons

Earlobe pulse sensor (with special noise reducing system)

Parts for Replacement

Exercise programs

Program

Specifications

Aerobic power measurement Fitness level evaluation by MOU value

Applicable range: age of 20 ~ 69 years

Auto training

Exercise under a constant pulse rate

Setting range: 60 ~ 180 bpm

Isopower training

Interval training

Hill profile training

Manual training

Exercise under a constant load(wattage)

Setting range: 25 ~ 200 watts

Exercise under one of the 4 patterns of

work and relief interval

Exercise under one of the 9 patterns of

hill profiles

Data Card (10 pcs)

(Part #7224950)

Thermal Paper (5 rolls/box)

Pulse Sensor

(Part #1655210)

Exercise under a constant pedal resistance (torque)

Setting range: 0.5 ~ 4.0 kg·m

(Part #7226502)

Alarm function

Buzzer sound

Upper pulse limit alarm, buzzer beeps continuously and

pedal torque is reduced to the minimum

Optional Parts

Pitch sound (120 times/min. cancellable), Upper pulse limit,

Confirmation of button function

KIS-00RC000-P

Backup Batteries

User's weight limit

Measurement

AAA(R03) x 2 for date memory (life: approx. 2 years)

Approx. 286 lbs. (130 kgs)

DC IN

EC-1500RS

Handlebar height

Saddle height

Length

30-23/32 ~ 53-5/32 inches (780 ~ 1350 mm)

30-5/16 ~ 46-1/16 inches (770 ~ 1170 mm)

39-3/8 inches (1000 mm)

Width

21-15/32 inches (545 mm)

-1

Weight

Approx. 68 lbs (31 kgs)

Connection with an

external computer

Two-way communication with an external computer is possible

with the optional accessory "RS232C Communication Kit"

Wireless heart rate

sensor

Optional item (Wireless heart rate sensor kit) applicable

U.S. Pat. 4775145, Pat. & Design Pat. Pending

The specifications and design are subject to alteration without notice for improvement

purpose.

**"CATEYE™" and "ERGOCISER™" are registered trademarks of CAT EYE CO., LTD.

Reading Stand

RS232C Communication Kit

Wireless Heart Rate Sensor Kit

(Part #7015501)

(Part #7015701)

(Part#7016700)

Download from Www.Somanuals.com. All Manuals Search And Download.

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, OSAKA, 546-0041 JAPAN

PHONE: 81-6-6719-7781 FAX: 81-6-6719-2362

0689131 (E)

Download from Www.Somanuals.com. All Manuals Search And Download.

Belkin Computer Accessories P35767ec User Manual
Berkel Mixer PM60 User Manual
Black Box Computer Hardware ACX048 User Manual
Blue Rhino Electric Heater 62900 User Manual
Bradford White Corp Water Heater ES 3000 User Manual
Broan Ventilation Hood QS330BC User Manual
Casio Cash Register PCR T265 User Manual
Char Broil Gas Grill 463742112 User Manual
Chicago Electric Cordless Sander 67707 User Manual
Chicago Electric Saw 94362 User Manual