electronic user's manual
file:///D|/EDFU/crt_17/edoc/english/107P/manual.html [6/25/2003 10:03:50 AM]
About This Electronic User's Manual
About This Electronic User's Manual
About This Guide
This electronic user's guide is intended for anyone who uses the Philips Color Monitor. It describes the
monitor's features, setup, operation and all other information, which is the same exact information described
in our printed version.
The sections are as follows:
related information you may need.
● About This Electronic User's Manual gives overview of what information are included as well as
notation icon descriptions and other documentation you can refer to.
specifications for this monitor.
● Installing Your Monitor describes the initial setup process and gives an overview of how to use the
monitor.
the help desk phone numbers and information on the applicable warranty of your product..
Other Documents You May Need
In addition to this Electronic User's Guide, you may need to refer to the following documentation:
● Philips Color Monitor Quick Start Guide which summarizes the steps for setting up the monitor. This
is included with this product.
Notational Descriptions
The following subsections describe notational conventions used in this document.
file:///D|/EDFU/crt_17/edoc/english/107P/ABOUT/ABOUT.HTM (1 of 2) [6/25/2003 10:03:55 AM]
About This Electronic User's Manual
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic
type. These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: This icon indicates important information and tips that help you make better
use of your computer system.
CAUTION: This icon indicates information that tells you how to avoid either potential
damage to hardware or loss of data.
WARNING: This icon indicates the potential for bodily harm and tells you how to
avoid the problem.
SMART HELP: This icon indicates helpful information when adjusting the On Screen
Display of your monitor.
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the
specific presentation of the warning is mandated by regulatory authority.
©2003 Koninklijke Philips Electronics N.V.
All rights reserved. Reproduction, copying, usage, modifying, hiring, renting, public performance, transmission and/or broadcasting in whole or in
part is prohibited without written consent of Philips Electronics N.V.
file:///D|/EDFU/crt_17/edoc/english/107P/ABOUT/ABOUT.HTM (2 of 2) [6/25/2003 10:03:55 AM]
107P Product Information
Product Information
Product Features
107P40:
● 17-inch (16.0" VIS) Real Flat color monitor featuring ICE technology for excellent front of screen
performance for use with MACs, PCs .
● Autoscan covers horizontal frequencies up to 97 kHz offering a maximum resolution of 1920 x 1440
with flicker free display of 1024 x 768 up to 115 Hz
● Flat aperture grille CRT with high-resolution 0.25 mm stripe pitch.
● LightFrame™ for brightest and sharpest display of movie and photo windows.
● Multimedia Base and USB Hub option
● FCC, CE (in selected countries only) and ISO9241, ISO14001 certified
LightFrame™ for Windows
Introduction
Philips LightFrame™ feature enriches the experience of pictures and video on a Philips CRT (picture tube)
monitor. LightFrame™ will boost the brightness and sharpness of photos and videos on the monitor screen.
To control the LightFrame™ feature in your monitor, you have to install the LightFrame™ application which
you will find on this CD-ROM.
Note
Philips LightFrame™ will only work with monitors that have been built to use this software. Earlier Philips
monitors or other manufacturers monitors will not work with this special software. It is recommended that
you install this software only on a Philips monitor designed to use it. These monitors can be identified by the
LightFrame™ logo on the front of the monitor.
This software is not designed for use with LCD flat screen monitors.
LightFrame™ will work with true Windows-based programs and DOS-based programs that operate in a
Windows environment. It will not work with DOS-based programs operating only in a DOS environment.
Language Selection
While English is the default language of LightFrame™, the User Interface can be set up to operate in Dutch,
file:///D|/EDFU/crt_17/edoc/english/107P/PRODUCT/PRODUCT.HTM (1 of 9) [6/25/2003 10:03:56 AM]
107P Product Information
French, German, Italian, Portuguese, Spanish, Simplified Chinese, Traditional Chinese or Korean.
Installation
1) To install LightFrame™, place the CD in the CD-ROM drive.
2) Next, when the menu of items on the CD appears on your screen, click on 'Install LightFrame™'.
3) Now, follow the on-screen prompts to properly install the program. The software checks to see if you
have a compatible monitor. You must agree to the license agreement terms for the software to install.
4) After installation, LightFrame™ automatically loads and the icon appears in the taskbar.
Notes
If LightFrame™ detects that your monitor is not LightFrame™ compatible, a message appears on the
monitor screen. If you see this message, you can select to abort or continue the installation. However, if you
continue the installation, LightFrame™ will probably not work on the monitor.
How to use LightFrame™
After installation, LightFrame™ starts up automatically whenever the computer is started.
For information about using LightFrame™ please refer to the help information which is available after
installation.
Compatibility
This version of LightFrame™ is compatible with
Windows 95
Windows 98
Windows Me (Millenium Edition)
Windows XP
Windows 2000 Professional Edition.
LightFrame™ 3 -- Frequently Asked Questions (and answers)
LightFrame™
Q: Is LightFrame™ 2 compatible with LightFrame™ 3?
A: No. If you run LightFrame™; 1 or 2 software with a Philips LightFrame™ 3 monitor, nothing will happen.
Q:Can I use LightFrame™ 3 software on my LightFrame™ 1 / 2 monitor.
A:No for a LightFrame™ 1 or 2 monitor you need to use LightFrame™ 1 or 2 software. It is however
file:///D|/EDFU/crt_17/edoc/english/107P/PRODUCT/PRODUCT.HTM (2 of 9) [6/25/2003 10:03:56 AM]
107P Product Information
possible to use the LightFrame™ 2 software on a LightFrame™ 1 monitor.
Q:What is the difference between LightFrame™ 1, LightFrame™ 2 and LightFrame™ 3?
A:LightFrame™ 1 was the very first generation of the LightFrame™ feature introduced by Philips. In that
version the user needs to manually turn on/off the feature and select the window or area to apply it to.
LightFrame™ 2 offers the automatic detection in Internet Explorer on top of the LightFrame™ 1 functions.
With this feature LightFrame™ will automatically scan a web page in Internet Explorer, find the largest
picture and enhance it.
LightFrame™ 3 offers everything that LightFrame™ 2 has but now with the possibility to enhance multiple
pictures at the same time. So in a web page LightFrame™ will find all the pictures and enhance them
simultaneously or in a photo viewing application you can enhance multiple photos at once. Furthermore
LightFrame™ 3 comes with an easy to activate full screen function. This is especially handy for games and
movies. Just one click on the full screen button and LightFrame™ enhances your total monitor.
Q:Can I upgrade my current Philips monitor to LightFrame™ 3?
A:No. For LightFrame™ 3 Philips developed special hardware which is build into the monitor. Therefore
upgrading from LightFrame™ 1 or 2 to 3 is not possible. It is however possible to upgrade your
LightFrame™ 1 monitor to LightFrame™ 2 by installing the LightFrame™ 2 software.
Q:Can I install LightFrame™ 3 over an older version?
A:When you install LightFrame™ 3 the setup wizard will scan your system to check if you have an older
version installed. If so, the setup wizard will remove that version before continuing with the installation of the
new version. Please be aware that for LightFrame™ 3 you also need a monitor which is capable of running
the LightFrame™ 3 feature.
Q:How can I tell which version LightFrame™ my monitor can support?
A:To check which version of LightFrame™ is supported by your monitor check the LightFrame logo which
you will find on the top, right-hand corner of the monitor. If this logo has a small 3 in it, your monitor is ready
for LightFrame™ 3. Otherwise you should use the LightFrame™ 1 or 2 software.
Q: How many windows can I enhance at the same time?
A:In LightFrame™ 3 it is possible to enhance up to 8 windows at the same time. It is however important to
understand that when other windows, toolbars or menus overlap the enhanced windows, the maximum
number of enhanced windows can be less.
Q:How many pictures can LightFrame™ enhance in Internet Explorer?
A:In Internet Explorer LightFrame™ 3 can enhance up to 16 pictures at the same time. LightFrame™ 3
filters the pictures it finds based on the minimum size of the picture therefore it may happen that some
pictures are not enhanced when you open a web page.
Q:Can I enhance two or more area s at the same time?
file:///D|/EDFU/crt_17/edoc/english/107P/PRODUCT/PRODUCT.HTM (3 of 9) [6/25/2003 10:03:56 AM]
107P Product Information
A:Yes. With LightFrame™ 3 you have the possibility to select several windows with pictures and videos and
enhance them at the same time.
Q:Some times my mouse changes to a light bulb with a plus sign and sometimes with a minus sign.
What is the difference?
A:The mouse pointer in the shape of a light bulb indicates that LightFrame™ is ready to accept a selection
from you for which window should be enhanced.
If there is a minus sign it means that you are moving over a window where LightFrame™ is already active
and clicking this window will switch the enhancement off. A plus sign appears when moving over a window
which is not enhanced and clicking that one will enable LightFrame™ on that window.
Q:What is wrong when my mouse changes into a light bulb with a red cross?
A:Nothing. It just means that your mouse moves outside the application where you already have one or
more windows enhanced. You can only select windows with in the same application. The cross indicates
that you move into an area where you cannot make a selection.
Q:Can I use LightFrame™ with Netscape?
A: You can use LightFrame™ with Netscape, but its functions are limited to manually highlighting the entire
Netscape client window. Since LightFrame™ is specifically designed for bright, high contrast photo and
video display, highlighting an entire Web page -- including text -- is not recommended.
For best results, we recommend you use LightFrame™ with Microsoft Internet Explorer version 5.0 or
higher. You can downloaded Internet Explorer free of charge from the Microsoft website
(www.microsoft.com). A copy of Internet Explorer 5.5 is also included on the CD-ROM shipped with your
monitor.
Q:Can I activate LightFrame™ on my entire screen?
A:Yes you can. And with LightFrame™ 3 this becomes even easier. There are three ways to do this: 1) click
the full screen button in the LightFrame control bar with your mouse. 2) Press the "windows" hotkey on your
keyboard and press "L". 3) Via the OSD menu, scroll to Extra controls, press "OK", then LightFrame On.
Q:When I apply LightFrame™ to a text document I get blurry characters, what is wrong?
A:Nothing is wrong. The effect which you see is due to the sharpness enhancement that LightFrame™ is
doing on your monitor. This sharpness improves a photo or video significantly however on black text on a
light background the effect is less favorable. Please keep in mind that LightFrame™ is developed to
enhance your photos and videos and not really for text or synthetic pictures.
You can decrease this effect by lowering the sharpness setting in the LightFrame™ 3 control panel.
Q: How can I tell if my monitor comes with LightFrame™ 3?
A: All Philips LightFrame™ 3 monitors display this logo on their front bezel:
file:///D|/EDFU/crt_17/edoc/english/107P/PRODUCT/PRODUCT.HTM (4 of 9) [6/25/2003 10:03:56 AM]
107P Product Information
Q: How do I use the LightFrame™ 3 control bar that appears at the top my screen?
A: The control bar is another upgrade that helps you run all LightFrame™ 3 s neat, new features. The
illustration below describes the tasks each button performs.
Accustomed to working with the original LightFrame™ tray icon? No problem: It s still there and can be
used to turn LightFrame™ on or off and check LightFrame™ status.
Technical Specifications*
CRT
• Size and deflection
• Grille pitch
17 inch / 41 cm ; 90° deflection angle
0.25 mm
Aperture grille, flat, high contrast, high brightness,anti-glare,
anti-static, anti reflection, light transmission 38%
• Tube type
• Phosphor
B22
file:///D|/EDFU/crt_17/edoc/english/107P/PRODUCT/PRODUCT.HTM (5 of 9) [6/25/2003 10:03:56 AM]
107P Product Information
• Recommended display area
• Maximum display area
12.0" x 9.0" / 306 x 230 mm
12.8" x 9.6" / 325 x 244 mm
SCANNING
• Horizontal scanning
• Vertical scanning
30 - 97 KHz
50-160 Hz
VIDEO
• Video dot rate
• Input impedance
- Video
203 MHz
75 ohm
- Sync
2.2 kOhm
0.7 Vpp
• Input signal levels
• Sync input signal
• Sync polarities
Separate sync
Positive and negative
WHITE COLOR TEMPERATURE
Chromaticity CIE coordinates:
• at 9300 degrees K
x = 0.283 / y = 0.297
x = 0.313 / y = 0.329
x = 0.332 / y = 0.347
• at 6500 degrees K
• at 5500 degrees K
sRGB
sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital
cameras, monitors, printers, scanners, etc.)
Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible
device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you
can rely on the correctness of the colors shown on your screen.
Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a
predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in the
monitor's OSD.
To do so, open the OSD by pressing the OK button on the front of your monitor. Use the down button to
go to Color temperature and press OK again. Then move the down button to go to sRGB and press OK
again.
Exit this OSD.
After this, please don't change the brightness or contrast setting of your monitor. If you change either of
these, the monitor will exit the sRGB mode and go to a color temperature setting of 6500K.
file:///D|/EDFU/crt_17/edoc/english/107P/PRODUCT/PRODUCT.HTM (6 of 9) [6/25/2003 10:03:56 AM]
107P Product Information
For more information on sRGB, please visit: www.srgb.com
* These information are subject to change without notice.
Automatic Power Saving
If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can
automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or
other input device is detected, the monitor will automatically "wake up". The following table shows the power
consumption and signaling of this automatic power saving features:
Power Management Definition
Power
VESA's Mode
Video
H-sync
V-sync Power Used
LED color
Saving (%)
0 %
ON
Active
Yes
No
Yes
No
Typical 77 W
Green
Yellow
OFF
Blanked
< 2W
97%
®
This monitor is ENERGY STAR® compliant. As an ENERGY STAR Partner, PHILIPS has
®
determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Physical Specifications
15.7" x 16.1" x 16.5" / 399 x 410 x 419 mm (including base)
15.7" x 14.7" x 16.5" / 399 x 373 x 419 mm (excluding base)
• Dimensions
• Weight
17.5 kg
• Power supply
90 - 264 VAC, 50/60Hz
0° to 40°C / 32° to 104°F
-25° to +65°C / -13° to +149°F
5% to 95%
• Temperature (operating)
• Temperature (storage)
• Relative humidity(storage)
file:///D|/EDFU/crt_17/edoc/english/107P/PRODUCT/PRODUCT.HTM (7 of 9) [6/25/2003 10:03:56 AM]
107P Product Information
* Resolution 1280 x 1024, standard size, contrast max., brightness 50%, 9300°, full white pattern.
* These information are subject to change without notice.
Pin Assignment
The 15-pin D-sub connector (male) of the signal cable (IBM systems):
Pin
No.
Pin
No.
Assignment
Assignment
1
2
Red video input
9
No pin
Green video input
10 Logic ground
Identical output - connected
to pin 10
3
4
Blue video input
11
Identical output - connected
to pin 10
12 Serial data line (SDA)
5
6
7
8
Ground
13 H. Sync
Red video ground
Green video ground
Blue video ground
14 V. Sync
15 Data clock line (SCL)
Views
Follow the links to see various views of the monitor and its components.
file:///D|/EDFU/crt_17/edoc/english/107P/PRODUCT/PRODUCT.HTM (8 of 9) [6/25/2003 10:03:56 AM]
107P Product Information
file:///D|/EDFU/crt_17/edoc/english/107P/PRODUCT/PRODUCT.HTM (9 of 9) [6/25/2003 10:03:56 AM]
Installing your Monitor
Installing your Monitor
Front View
Power button switches your monitor on.
OK button which when pressed will take you to the OSD controls
Contrast hotkey. When the UP arrow is pressed, the adjustment controls
for the CONTRAST will show up.
file:///D|/EDFU/crt_17/edoc/english/INSTALL_2/INSTALL.HTM (1 of 3) [6/25/2003 10:03:56 AM]
Installing your Monitor
UP and DOWN buttons are used when adjusting the OSD of your monitor
Brightness hotkey. When the RIGHT arrow is pressed, the adjustment
controls for BRIGHTNESS will show up.
LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used
in adjusting the OSD of your monitor.
Rear View
file:///D|/EDFU/crt_17/edoc/english/INSTALL_2/INSTALL.HTM (2 of 3) [6/25/2003 10:03:56 AM]
Installing your Monitor
1. Power in - attach power cable here.
2. Video In - this is a cable which is already attached to your monitor. Connect the other
end of the cable to your PC.
file:///D|/EDFU/crt_17/edoc/english/INSTALL_2/INSTALL.HTM (3 of 3) [6/25/2003 10:03:56 AM]
On-Screen Display
On-Screen Display
Description of the On Screen Display
What is the On-Screen Display?
This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitors
directly through an on-screen instruction window. The user interface provides user-friendliness and
ease-of-use when operating the monitor.
Basic and simple instruction on the control keys.
On the front controls of your monitor, once you press the
Controls window will pop up and you can now start making adjustments to your monitor's various features.
Use the or the keys to make your adjustments within.
button, the On Screen Display (OSD) Main
file:///D|/EDFU/crt_17/edoc/english/OSD/OSDDESC.HTM (1 of 3) [6/25/2003 10:03:56 AM]
On-Screen Display
file:///D|/EDFU/crt_17/edoc/english/OSD/OSDDESC.HTM (3 of 3) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
Frequently Asked Questions
1.
What does the "Designed for Windows" logo signify?
The "Designed for Windows" logo means your Philips monitor fulfills the requirements and
recommendations of the PC9x (97, 98, or 99) System Design Guide and passes stringent
WHQL tests.
2.
What is USB?
Think of USB as a smart plug for PC peripherals. USB automatically determines resources (like driver software
and bus bandwidth) required by peripherals. USB makes necessary resources available without user
intervention. Its three main benefits are:
● USB eliminates "Case angst," the fear of removing the computer case to install circuit board cards - that
often require adjustment of complicated IRQ settings -- for add-on peripherals.
● USB does away with "port gridlock." Without USB, PCs are normally limited to one printer, two Com port
devices (usually a mouse and modem), one Enhanced Parallel Port add-on (scanner or video camera,
for example) and a joystick. More and more peripherals for multimedia computers come on the market
every day. With USB, up to 127 devices can run simultaneously on a computer.
● USB permits "hot plug-in." No need to shut down, plug in, reboot and run set up to install peripherals. No
need to go through the reverse process to unplug a device. Bottom line: USB transforms today's
"Plug-and-Pray" into true Plug-and-Play!
3.
What is a USB hub?
Think of USB hub as a extension of USB ports. Normally, the PC provides only one or two USB
ports. To connect additional USB devices, you need a USB hub.
4.
What is Philips Monitors USB hub solution?
Increasingly, monitors include USB hub functionality. But not all users need or want a USB hub.
To give users freedom of choice, Philips provides an optional USB hub (type number
PCUH411). The USB hub consists of two parts that are normally connected: one is functional,
the other aesthetic. The aesthetic element is a removable cover. With the cover removed, the
USB hub can be attached to the base or pedestal of monitor. The attached USB hub can be
rotated to any position around the monitor's base. With this innovative Philips solution, your
USB hub is always within reach for convenient connection and disconnection of USB
peripherals.
6.
What models are Mac compatible?
All listed Philips monitors are Mac compatible. BUT, you may need an adapter to connect the
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (1 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
monitor to your Mac system. Please contact your dealer/reseller for details.
7.
What is TCO?
TCO is a Swedish abbreviation for the Swedish Confederation of Professional Employees.
8.
What is MPR?
MPR is a Swedish abbreviation for the Swedish National Board of Measurement and Testing.
9.
What are the differences between MPRII, TCO92, TCO95, TCO99 and TCO'03?
In the general hierarchy of standards, TCO'03/TCO99 is the highest level of certification. Next
is TCO95, which is "better" than TCO92, which, in turn, is better than MPRII. Below, we
compare the standards in each category.
-TCO 92 Phase out: June 30, 2000
-TCO 95 Will be end December 31, 2003
Emissions:
MPRII: Set low emission rules for visual displays.
TCO92: Imposed more stringent standards than MPRII.
TCO95: Further toughened TCO92 rules.
TCO99: Delineated even more severe standards and test procedures than TCO95.
TCO'03: Same as TCO99 standard + Testing uncertainty.
Safety:
MPRII: No requirement.
TCO92/95/99/03: All set requirements.
Energy Saving:
MPRII: No requirement.
TCO92: Standby mode < 30W, Off mode < 8W
TCO95: Standby mode < 30W, Off mode < 8W
TCO99: Standby mode < 15W, Off mode < 5W
TCO'03:Standby mode < 15W, Off mode < 5W
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (2 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
Visual Ergonomics:
MPRII: No requirement.
TCO92: No requirement.
TCO95: Set ergonomic rules including minimum contrast level, flicker and jitter.
TCO99: Tightened TCO95 rules.
TCO'03: Tighten TCO99 rule for CRT and new requirement of screen color for TFT LCD
Monitors.
Ecology:
MPRII: No requirement.
TCO92: No requirement.
TCO95: Set general ecological standards including recycling preparation, environmental policy
and environmental certification.
TCO99: Further tightened TCO95 norms.
TCO'03:Require the recycling information to users.
10. How do I enable the energy saving function?
Go to 'My Computer' and select 'Control Panel' followed by 'Monitor Control.' Select "All default
selection' and choose your Philips monitor model from the default driver list. Plug and Play will
automatically enable the EPA tick box for you. In DOS or Windows 3.1, you must first make
sure your PC supports power saving.
11. What is refresh rate?
"Refresh rate" describes the number of times an entire screen is vertically scanned each
second. In other words: If a monitor's refresh rate is 85 Hz, its screen is refreshed - or vertically
scanned - 85 times per second. A higher the refresh rate means better image stability and less
flicker. A high refresh rate helps users who work long hours in front of a monitor avoid eye
fatigue and stress. To change the refresh rate, go into "Start/Settings / Control Pannel / Display
/ Properties / Setting/Advance/Adaptor" Windows settings of the computer, the monitor will
automatically adjust itself to the video card.
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (3 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
12. Why does the picture on the screen appear to flicker?
A low refresh rate or electrical interference typically causes flickering in the picture. Possible
solutions include the following:
● Verify that the proper drivers are installed for your video card
● Make sure that all electrical devices (such as mobile phones) are at least 1m from the
monitor
● Place the monitor in another physical location away from electrical interference
● Adjust the refresh rate to 75hz or higher.
13. How do I adjust my monitor's resolution?
Available resolutions are determined by the capabilities of your video card and graphic driver.
Under Windows '95, you may select the desired available resolution through the 'Display
properties/Settings' menu.
14. How can I adjust the size, position and rotation of my screen?
Depending on the model you own, you can use your CustoMax Software, On Screen Display
(OSD) or control knobs located on the monitor.
15. What if I get lost when making monitor adjustments?
Simply press OK button then select "Reset to factory settings" to restore all settings.
™
16. What is LightFrame ?
™
LightFrame is a Philips technology breakthrough which offers a unique and revolutionary
TM
solution for boosting a monitor 's brightness and sharpness. With LightFrame , the user
experiences TV quality performance for video or photos without deterioration to the monitor 's
performance in windows used for other applications.
™
17. How does LightFrame work?
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (4 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
™
LightFrame consists of a software application and an Integrated Circuit (IC) embedded in the
monitor. Together, they boost brightness and sharpness in a user defined window or screen
TM
area. Unique LightFrame technology dramatically improves photo and video display quality.
™
18. Why is LightFrame important to me?
™
With LightFrame , selected Philips monitors deliver TV quality video and photo display while
maintaining monitor performance for text-based applications. The result is that movies and
other video are brighter and livelier; photos are more vibrant and lifelike.
19. Will anyone else have this?
™
LightFrame was invented, developed and patented by Philips. It is a unique feature that you
will find exclusively in Philips monitors.
™
20. Will LightFrame shorten the life of a monitor?
™
No. Extensive testing has confirmed LightFrame does not adversely affect monitor life.
Today's state-of-the-art Philips monitors employ improved phosphors and are designed for high
™
light output. LightFrame normally highlights photos and videos. Though the peak brightness
of the highlighted area is strongly increased, the average brightness - a determining factor for
cathode deterioration - is not normally increased. In any case, a special Automatic Beam
Limiter (ABL) circuit keeps a monitor 's maximum average brightness within acceptable levels.
™
21. I get a message warning that my monitor 'may not support LightFrame '. I am
certain my monitor does. What is wrong?
™
Only a Philips driver can determine if your monitor is equipped with LightFrame ; a generic
Windows driver cannot. Install the special Philips driver that came with your monitor. If the
warning continues to flash after your Philips driver is installed, ignore the message.
TM
LightFrame will function properly.
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (5 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
22. What will happen when my system is no longer connected to a LightFrame™
enabled monitor - for example, when I take my notebook on the road?
™
Philips exclusive LightFrame feature requires the combined operation of hardware that
resides in your monitor and software installed on your system. It only works when a monitor
with built-in hardware receives commands from system software. Without both the
TM
™
LightFrame hardware equipped monitor and system software, the LightFrame does not
function.
23. What is "XtraSpace Design" (XSD)?
XSD stands for XtraSpace Design, a Philips breakthrough that reduces a CRT display device's
footprint. Philips XSD monitors combine the world's smallest front-to-back footprint with
excellent front of screen performance.
24. How did Philips achieve XtraSpace Design?
Philips achieved this breakthrough in reduced footprint CRT display devices through short
depth tubes and a focused design process that squeezed every excess millimeter out of XSD
monitor desk space requirements.
25. What is Philips monitors' solution for audio?
Not all users need multimedia capabilities. To give users freedom of choice, Philips provides an
optional Multimedia Base (type number: 6G3B10). The Multimedia Base replaces the easily
removable standard pedestal of the monitor.
26. Which models can be incorporated with the Multimedia Base?
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (6 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
The following models can be incorporated with the Multimedia Base: 109B5, 109E5,109F5,
107B5, 107E5,107F5, 107S5, 107T5.
27. What are Philips Multimedia Base's specifications?
See detailed Multimedia Base specifications on the product information page.
28. Why is a Multimedia Base better than separate speakers?
The major advantage of the Multimedia Base is its minimal space requirements. In fact, it
hardly uses any extra space at all: monitor depth and width are unchanged. Only the monitor's
height is increased by only 3 centimeters.
29. Where can I buy a multimedia base to incorporate with my Philips monitor?
Please contact your dealer/reseller for details.
30. What does Auto Calibrate do?
It makes your monitor perform better and last longer. As a monitor becomes older, brightness
gradually deteriorates and its colors change. This well-known process effects all monitors.
Eventually after a number of years, the monitor's brightness deteriorates to below 50% of its
original value. At this stage, the usable life of a monitor is considered ended. Auto Calibrate
regularly readjusts color temperature and luminance to their original values.
31. How does Philips Auto Calibrate feature benefit me?
With Auto Calibrate, it takes a monitor's luminance 33 percent longer to deteriorate to the 50
percent level that marks the end of a display device's useful life. Thanks to Auto Calibrate, a
monitor with a normal life of 10,000 hours, for example, would last for 13,300 hours, a full one
third longer.
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (7 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
32. How does Auto Calibrate work?
During the calibration process, different predefined black and white images are displayed on
thescreen. The beam currents of the red, green and blue cannon are accurately measured and
compared to the original values stored in the monitor. By readjusting gain values of the
individual cannons, deviation is reduced to zero. Default values are stored during production. If
the user sets a new color temperature, this new value is saved as the new default value.
33. When should calibration be performed?
The calibration process takes less than six seconds. During this period, different specific
images are displayed. After the process is finalized, the original image is redisplayed. Constant
re-calibration is not required. Calibration should be performed after the monitor is warmed up.
Auto Calibration takes place when a monitor receives a signal indicating an imminent switch to
its sleep mode/stand-by mode.
34. Which models of Philips monitors are equipped with Auto Calibrate feature?
Auto Calibrate is currently available in the new 201P, 201B and 109P.
35. The Main Menu displays OSD MAIN MENU LOCKED . Pressing the front control
panels hasno effect. How can I unlock this function?
Press and hold the OSD menu key for about 10 seconds until picture displays "OSD MAIN
MENU UNLOCKED"
36. My screen shows NO SYNC INPUT , how can I get rid of this?
Check the following for possible solutions:
● Bent pins on the video cable
● Make sure the computer is turned on
● Ensure the VGA Cable is properly connected
● Ensure the BNC/D-Sub connector on the rear of the monitor is in the correct position,
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (8 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
newer models have this option in the On Screen Display under Input Signal Selection.
● Video card may be not a VESA standard (try the monitor with another computer)
37. Why does my monitor display "Out of Range"?
The video card installed in your computer may be too high for the monitor 's specifications.
Please contact your computer manufacturer for details on how to lower resolution for your
operating system.
38. What is Moire? Why does my monitor have this wavy phenomenon?
Moire is a natural effect or phenomenon of CRT that has the appearance of a wavy pattern,
which is repetitive and superimposed on the screen as ripple images. These are a few
suggestions to help reduce or minimize the effects:
● Some monitors have a Moire cancellation feature, activate it to the on position or adjust
the Moire cancellation function via the OSD on the monitor.
● Change resolution to the recommended standard for the specific monitor size.
● Change Window viewing pattern/scheme to a pattern where the Moire is less visible.
● Change horizontal and vertical size to optimize the reduction of the Moire effect.
39. What is CustoMax?
CustoMax is proprietary Philips software that allows user to control parameter (e.g. Size, Color,
Geometry) in place of the buttons on the front of the monitor. To install and run the CustoMax
software, you must have a USB compatible system and have a USB connection at the rear of
your monitor.
40. My monitor appears to be missing one or more colors. How do I correct this?
● If the OSD menu is also missing a color, please contact service for details
● Set color temperature to 9300 color coordination
● Check the video cable for any bent pins
● Video card could be defective (try the monitor with another computer).
41. When I degauss my monitor, it makes a loud noise. Is this normal?
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (9 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
Yes, when degaussing your monitor via the OSD, it is normal for the monitor to make a
relatively loud noise. Please be aware that many models will not degauss more than once
within any given time period (up to 10 minutes). This is due to the unit having a temperature
sensitive resistor. While the unit is degaussing, the resistor increases in value with heat and
once it reaches a certain temperature, the resistance will rise and prevent voltage from
reaching the degaussing coil. This is what stops the degausser, and this device's resistance
will decrease as it cools back off, enabling the degauss function to operate again. This is an
intentional design and is an industry standard, not just for Philips monitors. Please be aware
that not all models in the Philips range has this manual degauss function. Some models are
built with an auto degauss feature which automatically degausses the monitor when it is
switched on.
42. How do I adjust the picture on the screen?
Please perform the following to correct the picture image:
● Reset your monitor via the OSD menu
● Adjust the Horz (width) and/or Vert size (height) in the OSD
● Change monitor timing to work at the recommended resolution
43. The edge of the picture on the screen appears to be distorted. How can I correct
this?
Please perform the following to correct the picture image:
● A magnetic or electrical interference typically causes poor geometry in the picture. Place
the monitor in a different physical location
● Reset the monitor to the factory preset via the OSD menu
● Access the Geometry Menu in the OSD of the Monitor and perform the necessary
adjustments
● Change the monitor timing to the recommended resolution
44. The picture appears too dim. How can I correct this?
Adjust Brightness and/or Contrast via the monitor 's OSD. Some models have a Video Input
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (10 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
Select
under Advanced Controls in the monitor 's OSD. Most computers require it to be set at 0.7V.
Please review the following for possible solutions:
● If the OSD menu is also dim, please contact service for repair
● Reset the monitor via the OSD menu
● Change the color temperature settings to 9300 color coordination via the OSD menu
● Set the Contrast to maximum level (100) and Brightness to middle level (50)
Video card could be defective (try the monitor with another computer)
45. I have noticed two thin horizontal lines on the screen of my Philips monitor. Is this
normal?
This phenomenon can occur with Philips 107P, 109P and 201P monitors and is normal. Your
monitor is using an Aperture Grille, which consists of fine vertical wires to align the electron
beams with the phosphors on the screen. To prevent these vertical wires from vibrating and to
keep them properly aligned with the picture tube, two horizontal damper wires are required.
These are located on one-third and on two-third from the top of the screen. The result is that
you will see two very thin horizontal lines over your screen since the two wires are casting a
slight shadow on the screen surface. You will find these wires (line) in any monitor from Philips
and other brands using the Aperture Grille technology.
46. How can I increase the color display of my monitor?
The amount of video memory your video card holds determines the amount of colors that can
be displayed on your computer screen. To get the most out of your video card, you will need to
either install the latest drivers onto your computer or upgrade the video cards memory. Please
check with your computer or video card manufacturer for further details.
47. Why is there no picture on my monitor?
● Check the wall socket for power. Verify that there is power by connecting another
product.
● Ensure the power cable is correctly attached to both the wall socket and the monitor.
● Check that the power button is switched on.
● Unplug the monitor for approx. 1 minute and plug it in again. Switch the monitor back on.
48. Why is there no picture on my monitor even though the power LED is yellow/amber
or flashing green?
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (11 of 12) [6/25/2003 10:03:57 AM]
Frequently Asked Questions
● Reboot your computer while holding the Ctrl key on your computer. If you see any picture
during the boot procedure, please verify the settings of your video card (for Windows go
to Control Panel and select Display).
● Check that the video cable is not damaged, bent or that any of the pins in the connector
are damaged (please be aware that some VGA connectors have one missing pin). If
damaged, replace with a new cable.
● Check that the cable is attached correctly to the computer.
● Press any key on the keyboard to wake-up the computer from power saving mode.
49. Why is there no picture on my monitor even though the power LED is green?
● Verify the Contrast and Brightness setting of the monitor. First press and hold the 5 (-)
button to increase Contrast and then press and hold the 4 (+) button to increase
Brightness. These buttons are located on the front of your monitor.
● Press both the 5(-) button and the OK button at the same time to switch input A|B.
● Try and repeat step 48 above.
50. Why does the picture disappear after I press the on/off button quickly?
This is a unique Philips feature designed to preserve the life of your monitor. Please allow 5
seconds between powering off and on your monitor, your picture will then be restored.
file:///D|/EDFU/crt_17/edoc/english/FAQ.HTM (12 of 12) [6/25/2003 10:03:57 AM]
Glossary
Glossary
A
Autoscan
A microprocessor-based feature of Philips Brilliance monitors is able to detect automatically horizontal and
vertical frequencies of input signals with those of the installed video card. An autoscan monitor can thus
operate with a wide range of video cards. MultiSync, a registered trademark of NEC, provides a similar
function.
B
Balanced pincushion
See Geometric distortion
BNC connection
A special construction of connector used in some monitors with higher horizontal scanning frequency. The
BNC connection can provide the optimum shielding and matching characteristic impedance of video signal
path to ensure the best video performance.
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (1 of 18) [6/25/2003 10:03:58 AM]
Glossary
C
CE Mark
CE mark is displayed on products per EMC and LV ( low Voltage Device ) directives in compliance with
European Community safety, EMI and EMS requirements and is compulsory on products for sale in the
European Community.
Color temperature
A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black
body radiating with the same dominant frequency as the source.
Most Philips monitors offer the possibility of setting the color temperature to any desired value.
Contrast
The ratio between the brightness of the brightest and darkest parts of a picture. The darkest part of a picture
is set by the brightness of the unexcited phosphor, which is governed by the degree with which ambient light
is reflected. Contrast is therefore reduced in conditions of high ambient light levels. Black Matrix tubes
reflect less ambient light so exhibit higher contrast than other tubes.
Convergence error
Bean misalignment causing one or more of the three beams passing through the wrong aperture in the
shadow mask and striking a phosphor dot in the wrong triad.
Convergence error is expressed in mm often at three well-defined points on the screen, designated A, B
and C (see figure ). Also known as misconvergence.
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (2 of 18) [6/25/2003 10:03:58 AM]
Glossary
Points where convergence error is specified.
Convergence-error correction
A method of correcting for convergence error to insure that all three beams land simultaneously in the same
triad. This is usually accomplished by means of special convergence-error correction coils in the deflection
yoke.
CRT
Cathode-ray tube - the general term for all tubes in which one or more electron beams emitted by a cathode
are periodically scanned across a phosphor screen by means of deflection circuitry. A special form of the
cathode-ray tube is the TV and monitor picture tube.
CustoMax
Philips proprietary monitor control software that allows users to control parameters (e.g., Size, Color,
Geometry) using software running in Windows. CustoMax is compatible with existing VGA cards. See
CrystalClear FAQ and USB Bay FAQ.
D
DDC (Display Data Channel)
DDC is a communication channel for displays and computers. The DDC feature allows the monitor
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (3 of 18) [6/25/2003 10:03:58 AM]
Glossary
controller to be automatically configured to make optimal use of the display without manual user interaction.
DDC is implemented as part of the new Plug & Play approach introduced into the PC market to increase
user friendliness.
The three levels developed for Plug & play are: (1) DDC1, monitor send data to the PC; (2) DDC2B, PC can
request information from monitor; and (3) DDC2Bi which is a two-way communication - monitor can be
addressed and PC or graphics board can give commands to monitor.
DDC 1/2B
See DDC.
DDC 2Bi
See DDC.
Degaussing
The procedure of demagnetizing the shadow mask and associated metal parts of a picture tube at switch-on
to minimize picture distortion. This is usually accomplished by means of a special degaussing coil through
which a decaying alternating current is passed to generate an alternating magnetic field that gradually
decays to demagnetize the tube. Some monitors offer a manual degaussing facility that can be activated at
any time.
Digital control
Microprocessor-based digital control of picture parameters and video modes for complete control of picture
settings and modes and instant recall of all settings at the push of a button. This is a very advanced feature
that allows the user to switch to any required mode at any instant without having to spend time readjusting
the picture. It is currently available in most Philips monitors.
Dot pitch
The shortest distance between two phosphor dots of the same color on the screen. The smaller the dot
pitch, the better the resolution of the monitor.
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (4 of 18) [6/25/2003 10:03:58 AM]
Glossary
Dot rate
Frequency in MHz of the dot clock. It is a measure of the speed with which data is transferred between the
video card and subsequent processing circuitry.
Also known as video dot rate.
E
Electromagnetic radiation standards
International standards set to limit electromagnetic emissions from monitors. There are currently two
important standards both derived from regulations originally laid down by Swedish authorities.
MPR-II
The standard originally proposed by the Swedish National Board of Measurement and Testing. It set
maximum levels of electromagnetic radiation emitted by monitors, and has now been adopted as a world
standard. MPR-II defines maximum permitted electrostatic, magnetic and electric field levels measured at a
distance of 50 cm from the center of the monitor (see table).
TCO
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (5 of 18) [6/25/2003 10:03:58 AM]
Glossary
In 1991, the Swedish Tjänstemannens Central Organization (TCO, Swedish confederation of Professional
Employees ) set a standard even more severe than MPR-II, especially for alternating electric fields (AEF).
The TCO standard is more severe since not only are the permitted field levels reduced compared with
MPR-II, but the measuring distance is also reduced (see table).
Electromagnetic radiation standards
EMI (Electrical Magnetic Interference)
The electrical and/or magnetic radiation coming from the working electrical or electronic equipment.
EMS (Electrical Magnetic Sustainment)
The ability of electrical or electronic equipment to function properly in the environment with electrical and/or
magnetic interference.
F
Flicker
Very rapid variations in picture intensity caused by the finite time required for the electron beam to scan a
picture onto the screen. Two kinds of flicker occur: line flicker caused by the electron beam scanning-in
each line of the picture; and frame flicker (or field flicker if the picture is interlaced) caused by the frame
repetition rate of 50 frames/second. Frame flicker is noticeable with GUI and DTP software (which have a
light background), and can be very disturbing, especially for those who work regularly with displays -
contributing to eye strain, headaches, visual blurring, stress, etc. The problem can, however, be eliminated
by increasing the refresh rate (number of frames/second) of the monitor to a value above around 70 Hz.
Sensitivity to flicker appears to diminish with increasing age.
H
Hertz
The unit of frequency named after the physicist Heinrich Hertz (1857-1894). 1 hertz (Hz) is equal to 1
cycle/second.
Horizontal dot pitch
See Dot pitch.
Horizontal scanning frequency
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (6 of 18) [6/25/2003 10:03:58 AM]
Glossary
Also called line frequency and expressed in kHz, it is the number of video lines written on the screen every
second (from left to right). The higher the horizontal scanning frequency, the better the resolution (i.e., the
higher the resolution and/or the higher the refresh rate).
I
INF File
INF file (Information File)
Information (INF) files store information in a specific format. The set-up functions retrieve information from
the INF file to use when performing installation operations. Examples of the type of information stored in an
INF file include INI and registry changes, file names, and locations of the source files on source media.
Interlaced/non-interlaced
Interlaced.
The method of writing a picture on the screen by initially writing all even lines and subsequently writing all
odd lines of the picture. Result: The complete picture is composed of two interlaced half pictures (or fields).
With interlacing, a vertical (or field) frequency of 50 Hz means a picture (or frame) frequency of 25 Hz.
Non-interlaced.
The method of writing a picture on the screen by successive video lines of the picture so that a full frame is
written onto the screen in one vertical sweep of the beams. With a non-interlaced display, a vertical
frequency of 50 Hz means a picture (or frame) frequency of 50 Hz. At any given resolution, non-interlaced
modes are preferable to interlaced modes; however, generation of non-interlaced modes is more expensive.
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (7 of 18) [6/25/2003 10:03:58 AM]
Glossary
L
Linearity
The degree to measure the actual location of a pixel on the screen corresponds with its intended location. (
see figure )
Line frequency
See Horizontal scanning frequency.
Low-emission monitor
A monitor that complies with international standards on radiation.
See Electromagnetic radiation standards.
Low-frequency electric and magnetic fields
Alternating fields generated by the deflection yoke. These are subject to increasing attention, notably by
governing authorities, the trade and the press. Although there is no scientific evidence that monitor
emissions are harmful, much effort has gone into reducing emissions on the principle of better safe than
sorry. Currently, there are two areas of interest: very-low frequency (VLF) electric and magnetic fields
extending from 2 kHz to 400 kHz, and extreme low frequency (ELF) fields extending from 5 Hz to 2 kHz.
See also Electromagnetic radiation standards.
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (8 of 18) [6/25/2003 10:03:58 AM]
Glossary
M
Moiré effect
A fringe pattern arising from the interference between two superimposed line patterns.
In a monitor it comes from the interference between the shadow mask pattern and the video information
(video moiré), and between the shadow mask pattern and the horizontal line pattern (scan moiré). It shows
itself as wavy patterns on the screen and becomes more noticeable as monitor resolution increases. Since
the video signal varies continuously, little can be done about video moiré. Scan moiré depends on the
horizontal scanning frequency and can be alleviated by appropriate choice of frequency. Autoscan
(MultiSync) monitors, which operate over a range of scanning frequencies, may sometimes exhibit moiré in
certain video modes.
MPR
See Electromagnetic radiation standards.
MultiSync monitor
See Autoscan monitor.
N
Non-interlaced
See Interlaced/non-interlaced.
O
OSD (On Screen Display)
The feature that allows an end user to adjust screen performance and parameters of monitors directly
through an on-screen instruction window. See CustoMax in CrystalClear section.
Overscan
The practice in which areas without useful video information are scanned outside the visible screen area in
order to make maximum use of the screen for display of active video information. This practice is
occasionally necessary because some video cards generate a video pattern that is smaller than the visible
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (9 of 18) [6/25/2003 10:03:58 AM]
Glossary
screen area, resulting in an image that is smaller (and less legible) than it needs to be.
P
Parallelogram Distortion
See Geometric distortion.
Phosphor
Generic name for the class of substances that exhibit luminescence. To produce a picture on screen,
phosphors are deposited on the inner surface of the picture-tube screen and excited into luminescence by
the electron beam. Typical examples of phosphors are P22 medium short-persistence phosphor and EBU
high-color-saturation phosphor.
Pin-cushion Distortion
See Geometric distortion.
Pixel
Abbreviation for picture element, the smallest element of the picture that can be displayed on the screen.
The smaller the pixel size, the better the resolution of the monitor. Pixel size is determined by the size of the
electron spot on the screen and not necessarily by the phosphor dot pitch (the size of the triad). Thus, a
monitor with a large electron spot covering several triads can exhibit poor resolution even though its dot
pitch is small.
Pixel frequency
The number of pixels that can be written in a video line per second.
Pixel rate
See pixel frequency
Plug-and-Play
See DDC. See USB section.
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (10 of 18) [6/25/2003 10:03:58 AM]
Glossary
R
Raster
The area on screen that electron beam can reach.
Refresh rate
See Vertical scanning frequency.
Resolution
The number of pixels that can be displayed on the screen. The resolution is specified as the number of
pixels in a line multiplied by the number of horizontal lines.
See also video graphic adapter.
Rotation function
The feature that allows users to adjust the whole screen rotating to be horizontal.
Because of the magnetic field of earth, the screen of monitor will be tilt when the screen faces toward the
different direction.
S
Screen coatings
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (11 of 18) [6/25/2003 10:03:58 AM]
Glossary
Anti-Static coatings
Due to bombardment by beam electrons, monitor screens become electrically charged when in use.
Electrically charged screens surfaces can attract dust particles. An Anti-Static coating is a conductive
coating deposited on the screen (or on a glass panel immediately in front of the screen) that conducts away
the charge and prevents screen dust build-up.
AGAS (Anti-Glare, Anti-Static) coating
AGAS is a silica coating applied to the surface of the screen by a spinning and spraying process. It operates
by diffusing reflected light to blur images of light sources on the screen. To provide anti-static properties, the
coating is impregnated with small conductive particles.
ARAS (Anti-Reflection, Anti-Static) coating
ARAS is one of the most effective anti-reflection/anti-static screen treatments currently available. It is
composed of a multi-layer structure of transparent dielectric material that suppresses specular reflections by
broadband interference effects at the screen surface. Anti-static properties are provided by a single
conductive layer within the multi-layer structure.
With ARAS, the intensity of reflected light is reduced from around 4.5% of the incident light (the reflectivity of
uncoated screens) to less than 0.5%. ARAS also has a major advantage over other screen treatments: It
doesn't diffuse or scatter reflected light, so picture contrast and sharpness remain completely unimpaired.
It's also easy to clean and tough enough to withstand commercially available cleaning agents.
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (12 of 18) [6/25/2003 10:03:58 AM]
Glossary
The ARAS coating reflects only about 0.5% of the incident light.
AGRAS (Anti-Glare anti-Reflection Anti-Static) coating.
A combined anti-reflection, anti-glare, anti-static coating.
Self-test function
A monitor equipped with hardware or software to automatically detect cable connection status.
Shape
Deviation of a reproduced picture from its intended shape. The following types of distortion are most
common:
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (13 of 18) [6/25/2003 10:03:58 AM]
Glossary
SOG (Synchronization On Green)
A properly functioning color monitor requires five kinds of signals: horizontal sync pulse, vertical sync pulse,
red color signal, green color signal and blue color signal. Signals from a PC are transmitted to a monitor
using one of three methods:
1. Separate sync: Horizontal and Vertical sync signals transmitted separately
2. Composite sync: Horizontal and vertical sync pulses mixed into a single signal train.
3. SOG: Horizontal and vertical sync pulses mixed, then combined with the green color signal.
T
TCO
See Electromagnetic radiation standards.
Tilt function
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (14 of 18) [6/25/2003 10:03:58 AM]
Glossary
See rotation function.
Trapezoid distortion
See Geometrical distortion.
TTL signal
A TTL (Transistor-transistor-logic) signal is a digital signal level for controlling the screen colors. With TTL
driving, the red, green and blue signals can only be switched on or off or provided with an intensity signal. A
TTL-driven monitor can thus display a maximum of 64 colors. Video standards such as MDA, CGA and
EGA are based on TTL level.
U
USB or Universal Serial Bus
A smart plug for PC peripherals. USB automatically determines resources (like driver software and bus
bandwidth) required by peripherals. USB makes necessary resources available without user intervention.
● USB eliminates "case angst" -- the fear of removing the computer case to install add-on peripherals.
And USB also eliminates adjustment of complicated IRQ settings when installing new peripherals.
● USB does away with "port gridlock." Without USB, PCs are normally limited to one printer, two Com
port devices (usually a mouse and modem), one Enhanced Parallel Port add-on (scanner or video
camera, for example) and a joystick. More and more peripherals for multimedia computers arrive on
the market every day. With USB, up to 127 devices can run simultaneously on a computer.
● USB permits "hot plug-in." There's no need to shut down, plug in, reboot and run set-up to install
peripherals. And no need to go through the reverse process to unplug a device.
In short, USB transforms today's "Plug-and-Pray" into true Plug-and-Play!
Hub
A Universal Serial Bus device that provides additional connections to the Universal Serial Bus.
Hubs are a key element in the plug-and-play architecture of USB. The Figure shows a typical hub. Hubs
serve to simplify USB connectivity from the user's perspective and provide robustness at low cost and
complexity.
Hubs are wiring concentrators and enable the multiple attachment characteristics of USB. Attachment points
are referred to as ports. Each hub converts a single attachment point into multiple attachment points. The
architecture supports concatenation of multiple hubs.
The upstream port of a hub connects the hub towards the host. Each of the other downstream ports of a
hub allows connection to another hub or function. Hubs can detect, attach and detach at each downstream
port and enable the distribution of power to downstream devices. Each downstream port can be individually
enabled and configured at either full or low speed. The hub isolates low speed ports from full speed
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (15 of 18) [6/25/2003 10:03:58 AM]
Glossary
signaling.
A hub consists of two portions: the Hub Controller and Hub Repeater. The repeater is a protocol-controlled
switch between the upstream port and downstream ports. It also has hardware support for reset and
suspend/resume signaling. The controller provides the interface registers to allow communication to/from
the host. Hub specific status and control commands permit the host to configure a hub and to monitor and
control its ports.
Device
A logical or physical entity that performs a function. The actual entity described depends on the context of
the reference. At the lowest level, device may refer to a single hardware component, as in a memory device.
At a higher level, it may refer to a collection of hardware components that perform a particular function, such
as a Universal Serial Bus interface device. At an even higher level, device may refer to the function
performed by an entity attached to the Universal Serial Bus; for example, a data/FAX modem device.
Devices may be physical, electrical, addressable, and logical.
Downstream
The direction of data flow from the host or away from the host. A downstream port is the port on a hub
electrically farthest from the host that generates downstream data traffic from the hub. Downstream ports
receive upstream data traffic.
Upstream
The direction of data flow towards the host. An upstream port is the port on a device electrically closest to
the host that generates upstream data traffic from the hub. Upstream ports receive downstream data traffic.
UPS (Universal Power Supply)
The monitor with UPS feature can work in different countries with various mains voltage.
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (16 of 18) [6/25/2003 10:03:58 AM]
Glossary
V
Vertical dot pitch
See Dot pitch.
Vertical scanning frequency
Expressed in Hz, this is the number of fields written to the screen every second in interlaced mode. In
non-interlaced mode vertical scanning frequency is the number of frames (complete pictures) written to the
screen every second (also known as refresh rate).
Vertical sync pulses
A train of square shaped waveforms that define the start of a new frame.
VESA
Video Electronic Standards Association, a consortium of manufacturers formed to establish and maintain
industry-wide standards for video cards and monitors. VESA was instrumental in the introduction of the
Super VGA and Extended VGA video graphics standards (see Video graphics adapters) with a refresh rate
of 70 Hz, minimizing flicker and helping to reduce operator eyes fatigue and stress.
Video dot rate
See Dot rate.
Video graphics adapters
A card equipped with a character or graphic generator and video memory, which maps to the screen. A
microprocessor scans video memory and translates bit information from the computer into displayable video
signals for the monitor. These cards comply with various standards that determine the nature and quality of
the display.
VGA (Video Graphics Array), introduced in 1987, was the first analog card. It offered still higher resolution
than EGA: 640 X 480 pixels for graphics and 720 x 400 pixels for text, and a color palette of 256 colors.
VGA could also emulate EGA and CGA.
Super VGA, devised by VESA in 1989, offers a resolution of 800 x 600 pixels.
Extended VGA, introduced by VESA in 1991, offers a top resolution of 1024 x 768 pixels (non-interlaced)
and a refresh rate slightly higher than IBM's XGA 8514A.
High-end, graphics adapters, introduced over the last three years for professional workstations, offer top
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (17 of 18) [6/25/2003 10:03:58 AM]
Glossary
resolutions from 1280 x 1024 to 1600 x 1280, horizontal line frequencies up to 90 kHz and bandwidths up to
200 MHz.
VIS (Viewable Image Size)
The real screen dimensions that users can see measured diagonally. The VIS of a monitor is always less
than the so called screen size of a monitor. For example, the VIS of a 17-inch monitor is only about 16
inches. It depends on the useful screen size of CRT and the opening of a monitor's front cabinet.
file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.HTM (18 of 18) [6/25/2003 10:03:58 AM]
Download and Print
Download and Print
This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your hard
disk, then viewed and printed with Acrobat Reader or through your browser.
If you do not have Adobe¨ Acrobat Reader installed, click on the link to install the application. Adobe®
Download instructions:
To download the file:
1. Click-and-hold your mouse over the icon below. (Win95/98 users right-click)
2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to Disk'.
3. Choose where you would like to save the image; click 'Save' (if prompted to save as either 'text' or
'source', choose 'source').
Printing instructions:
To print the manual:
1. With the manual file open, follow your printer's instructions and print the pages you need.
English language manual
file:///D|/EDFU/crt_17/edoc/english/DOWNLOAD/DOWNLOAD.HTM (1 of 2) [6/25/2003 10:03:58 AM]
Download and Print
file:///D|/EDFU/crt_17/edoc/english/DOWNLOAD/DOWNLOAD.HTM (2 of 2) [6/25/2003 10:03:58 AM]
Troubleshooting
Troubleshooting
Common Problems
Having trouble? Something not working? Before calling for help, try these suggestions.
Having this
Check these items
problem?
● Make sure the Power cable is plugged into the power outlet and
back of the monitor.
No Picture
● Power button on the front of your monitor should be in the ON
position.
(Power LED not lit)
● Disconnect the monitor from the power outlet for about one
minute, then re-connect the power outlet again.
● Make sure the computer is turned on.
● Make sure the monitor cable is properly connected to your
The screen says "NO
computer.
SIGNAL INPUT FROM
INPUT A (or B)"
● Press OK and UP knobs on front control panel simultaneous to
switch the Input Signal A/B.
● Check to see if the monitor cable has bent pins.
● Make sure the computer is turned on.
The screen says "NO
SIGNAL INPUT"
● Make sure the monitor cable is properly connected to your
computer.
● Check to see if the monitor cable has bent pins.
The screen says
"FREQUENCY IS OUT
OF RANGE"
● Change the settings of resolution and/or refresh rate of your
computer. Refer to the Quick Start Guide or contact your
computer vender for details.
● The Energy Saving feature may be activated. Drag your mouse
or click any keypad on your keyboard to exit Energy Saving
mode.
No Picture
● Make sure the computer is turned on.
● Make sure the monitor cable is properly connected to your
(Power LED is amber or
yellow)
computer.
● Check to see if the monitor cable has bent pins.
● Press OK and UP knobs on front control panel simultaneous to
switch the Input Signal A/B. (not for all monitors)
● Make sure the Brightness and Contrast controls are set correctly.
No Picture
● Make sure the monitor cable is properly connected to your
computer.
(Power LED is green)
● Check to see if the monitor cable has bent pins.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/saf_troub.htm (1 of 2) [6/25/2003 10:09:44 AM]
Troubleshooting
The screen says
"CONTROL MENU IS
LOCKED" when you
press the OK knob
● Press the OK knob and hold for around 15 seconds to release
the lock.
Picture is too large or too
small
● Adjust the Horizontal Size and/or Vertical Size. Refer to the On
Screen Display chapter for details.
Edges of the picture are
not square
● Refer to the Adjust Shape item in On Screen Display chapter for
details.
● Remove any nearby magnetic objects.
● "Degauss" your monitor. Refer to the Degauss item in On Screen
Color appears blotchy
Display chapter for details.
● Face the monitor toward the East for the best picture quality.
● Make sure the monitor cable is properly connected to your
computer.
● "Degauss" your monitor. Refer to the Degauss item in On Screen
Missing one or more
colors
Display chapter for details.
● Check to see if the monitor cable has bent pins.
● Check the Color Temperature. Refer to the Color Temperature
item in On Screen Display chapter for details.
● Make sure the Brightness and Contrast controls are set correctly.
Dim Picture
● "Degauss" your monitor. Refer to the Degauss item in On Screen
Display chapter for details.
● Eliminate the use of extension cables and/or video switch box.
Picture has double image
● Adjust Moire to zero. Refer to the Adjust Moire item in On Screen
Display chapter for details.
● Low down the Contrast and/or Brightness level.
● Adjust Moire to zero. Refer to the Adjust Moire item in On Screen
Picture is not sharp
Unstable picture
Display chapter for details.
● "Degauss" your monitor. Refer to the Degauss item in On Screen
Display chapter for details.
● Increase the refresh rate of video signal at least to 75Hz. Refer to
the Quick Start Guide or contact your computer vender for
details.
● Adjust Moire to zero. Refer to the Adjust Moire item in On Screen
Display chapter for details.
For further assistance, refer to the Consumer Information Centers list to contact your local Philips
distributor.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/saf_troub.htm (2 of 2) [6/25/2003 10:09:44 AM]
Regulatory Information
Regulatory Information
TCO '95/99 Information (For TCO Model Only)
Congratulations!
You have just purchased a TCO' 95 or TCO' 99approved and labeled product! Your choice has provided
you with a product developed for professional use. Your purchase has also contributed to reducing the
burden on the environment and also to the further development of environmentally adapted electronics
products.
Why do we have environmentally labeled computers?
In many countries, environmental labeling has become an established method for encouraging the
adaptation of goods and services to the environment. The main problem, as far as computers and other
electronics equipment are concerned, is that environmentally harmful substances are used both in the
products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of
electronics equipment, most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important
from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing
emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running
continuously and thereby consumes a lot of energy.
What does labeling involve?
This product meets the requirements for the TCO' 95/TCO' 99 scheme which provides for international and
environmental labeling of personal computers. The labeling scheme was developed as a joint effort by the
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (1 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The
Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy
Administration).
Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of
electric and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands impose restrictions on the presence and use of heavy metals, brominated and
chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must
be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be
adhered to in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.
Labeled products must meet strict environmental demands, for example, in respect of the reduction of
electric and magnetic fields, physical and visual ergonomics and good usability.
Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): [email protected]
Current information regarding TCO' 95/TCO' 99 approved and labeled products may also be obtained
via the Internet, using the address: http://www.tco-info.com/
Environmental Requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is
to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist
of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame
retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants
containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including
reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame
retardants have been found in human blood and researchers fear that disturbances in fetus development
may occur.
The relevant TCO' 95/TCO' 99 demand requires that plastic components weighing more than 25 grams
must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed
in the printed circuit boards since no substitutes are available.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (2 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
Cadmium**
Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO' 95/ TCO'99
requirement states that batteries, the color-generating layers of display screens and the electrical or
electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in
high doses. The relevant TCO' 95/TCO' 99 requirement states that batteries may not contain any mercury. It
also demands that mercury is not present in any of the electrical or electronics components associated with
the labeled unit.
CFCs (freons)
The relevant TCO' 95/TCO' 99 requirement states that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit
boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing
increased reception on earth of ultraviolet light with increased risks e.g. skin cancer (malignant melanoma)
as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TCO' 95/TCO' 99 requirement permits the
inclusion of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.
TCO' 03 Information
Congratulations!
The display you have just purchased carries the TCO'03
Displays label. This means that your display is designed,
manufactured and tested according to some of the strictest
quality and environmental requirements in the world. This
makes for a high performance product, designed with the
user in focus that also minimizes the impact on our natural
environment.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (3 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
Some of the features of the TCO'03 Display requirements.
Ergonomics
● Good visual ergonomics and image quality in order to improve the working environment
for the user and to reduce sight and strain problems. Important parameters are luminance,
contrast, resolution, reflectance, colour rendition and image stability.
Energy
● Energy-saving mode after a certain time-beneficial both for the user and the environment
● Electrical safety
Emissions
● Electromagnetic fields
● Noise emissions
Ecology
● The product must be prepared for recycling and the manufacturer must have a certified
environmental management system such as EMAS or ISO 14 000
● Restrictions on
chlorinated and brominated flame retardants and polymers
heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO Development in co-
operation with scientists, experts, users as well as manufacturers all over the world. Since the
end of the 1980s TCO has been involved in influencing the development of IT equipment in a
more user-friendly direction. Our labelling system started with displays in 1992 and is now
requested by users and IT-manufacturers all over the world.
For more information, please visit
www.tcodevelopment.com
Recycling Information for Customers
Philips establishes technically and economically viable objectives to optimize the environmental
performance of the organization's product, service and activities.
From the planning, design and production stages, Philips emphasizes the important of making products that
can easily be recycled. At Philips, end-of-life management primarily entails participation in national
take-back initiatives and recycling programs whenever possible, preferably in cooperation with competitors.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (4 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
There is currently a system of recycling up and running in the European countries, such as The
Netherlands, Belgium, Norway, Sweden and Denmark.
In U.S.A., Philips Consumer Electronics North America has contributed funds for the Electronic Industries
Alliance (EIA) Electronics Recycling Project and state recycling initiatives for end-of-life electronics products
from household sources. In addition, the Northeast Recycling Council (NERC) - a multi-state non-profit
organization focused on promoting recycling market development - plans to implement a recycling program.
In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA) to
follow the IT product recycling management process, detail can be found in web site www.epa.gov.tw
For help and service, please contact Consumers Information Center or F1rst Choice Contact Information
Center in each country or the following team of Environmental specialist can help.
Mr. Job Chiu - Environment manager
Philips Electronics Industries (Taiwan) Ltd, Monitor Business Unit
E-mail: [email protected]
Tel: +886 (0) 3 454 9839
Mr. Maarten ten Houten - Senior Environmental Consultant
Philips Consumer Electronics
E-mail: [email protected]
Tel: +31 (0) 40 27 33402
Ms. Patricia A. Franco
Philips Electronics North America
E-mail: [email protected]
Tel: +1 202 962 8550
CE Declaration of Conformity
● Philips Consumer Electronics declare under our responsibility that the product is in conformity with
the following standards
- EN60950:1992+A1+A2+A3+A4+A11 (Safety requirement of Information Technology Equipment)
- EN55022:1998 (Radio Disturbance requirement of Information Technology Equipment)
- EN55024:1998 (Immunity requirement of Information Technology Equipment)
- EN61000-3-2:1995 (Limits for Harmonic Current Emission)
- EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable
- 73/23/EEC (Low Voltage Directive)
- 89/336/EEC (EMC Directive)
- 93/68/EEC (Amendment of EMC and Low Voltage Directive)
and is produced by a manufacturing organization on ISO9000 level.
● The product also comply with the following standards
- ISO9241-3, ISO9241-7, ISO9241-8 (Ergonomic requirement for Visual Display)
- ISO13406-2 (Ergonomic requirement for Flat panels)
- GS EK1-2000 (GS specification)
- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)
- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)
- TCO95, TCO99, TCO03 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology
and Emission,
TCO: Swedish Confederation of Professional Employees) for TCO versions
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (5 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
Energy Star Declaration
PHILIPS
107P4*
This monitor is equipped with a function for saving energy which supports the VESA Display Power
Management Signaling (DPMS) standard. This means that the monitor must be connected to a
computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299/94.
Time settings are adjusted from the system unit by software.
NUTEK
VESA State
ON
LED Indicator
Green
Power Consumption
Typical 77W
Normal operation
Power Saving
Alternative2
One Step
OFF
Yellow
< 2 W
®
As an ENERGY STAR Partner, PHILIPS has determined that this product meets
®
the ENERGY STAR guidelines for energy efficiency.
We recommend you switch off the monitor when it is not in use for quite a long time.
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (6 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer
device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or
excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
Commission Federale de la Communication (FCC Declaration)
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de
class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon
à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une
installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences
qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer
des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir
l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la
cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce
qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur
pourrait essayer de corriger la situation en prenant les mesures suivantes:
● Réorienter ou déplacer l'antenne de réception.
● Augmenter la distance entre l'équipement et le récepteur.
● Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.
● Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de
conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement.
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (7 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU
REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.
EN 55022 Compliance (Czech Republic Only)
VCCI Notice (Japan Only)
This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for
Information technology equipment. If this equipment is used near a radio or television receiver in a domestic
environment, it may cause radio Interference. Install and use the equipment according to the instruction
manual.
Class B ITE
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (8 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
MIC Notice (South Korea Only)
Class B Device
Please note that this device has been approved for non-business purposes and may be used in any
environment, including residential areas.
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket).
All equipment that works together (computer, monitor, printer, and so on) should have the same power
supply source.
The phasing conductor of the room's electrical installation should have a reserve short-circuit protection
device in the form of a fuse with a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply
socket, which should be located near the equipment and easily accessible.
A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements
of standards PN-93/T-42107 and PN-89/E-06251.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (9 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
North Europe Information (Nordic Countries)
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR
DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER
NEMT TILGÆNGELIGE.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (10 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI
IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR
STØMTILFØRSEL ER LETTE Å NÅ.
BSMI Notice (Taiwan Only)
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch
Röntgenstrahlen" festgelegten Vorschriften.
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der
Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4
der Röntgenverordnung erfüllt sind.
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß
1. Reparaturen nur durch Fachpersonal durchgeführt werden.
2. nur original-Ersatzteile verwendet werden.
3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (11 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem
Zeichenkontrast wären die Folge).
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
End-of-Life Disposal
Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle
your product to increase the amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old monitor from your local Philips
dealer.
Information for UK only
WARNING - THIS APPLIANCE MUST BE
EARTHED.
Important:
This apparatus is supplied with an approved
moulded 13A plug. To change a fuse in this type
of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362
5A,A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
3-pin plug fitted in its place.
If the mains plug contains a fuse, this should
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (12 of 13) [6/25/2003 10:09:45 AM]
Regulatory Information
have a value of 5A. If a plug without a fuse is
used, the fuse at the distribution board should
not be greater than 5A.
Note: The severed plug must be destroyed to
avoid a possible shock hazard should it be
inserted into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in
accordance with the following code:
BLUE - "NEUTRAL" ("N")
BROWN - "LIVE" ("L")
GREEN & YELLOW - "EARTH" ("E")
1. The GREEN AND YELLOW wire must be
connected to the terminal in the plug which is
marked with the letter "E" or by the Earth symbol
or coloured GREEN or GREEN AND
YELLOW.
2. The BLUE wire must be connected to the
terminal which is marked with the letter "N" or
coloured BLACK.
3. The BROWN wire must be connected to the
terminal which marked with the letter "L" or
coloured RED.
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath of
the lead - not simply over the three wires.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/regs/regulat.htm (13 of 13) [6/25/2003 10:09:45 AM]
Other Related Information
Other Related Information
Information for Users in the U. S.
For units set at 115 V :
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a
maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
For units set at 230 V:
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a
maximum of 15-feet long and a tandem blade, grounding type attachment plug rated 15 A, 250 V.
Information for Users outside the U.S.
For units set at 230 V:
Use a Cord Set rated minimum 5 A, 250 V ( for units set at 230V ) or 10A, 125V (for units set at 115V). The
Cord Set should have the appropriate safety approvals for the country in which the equipment will be
installed.
file:///D|/EDFU/crt_17/edoc/english/107P/SAFETY/saf_other.htm [6/25/2003 10:09:45 AM]
6G3B11 Multimedia Base (option)
6G3B11 Multimedia Base (option)
Technical Specifications*
• Output power
• Bass Boost
2 x 1.5W RMS / 36W PMPO
• Headphone connection
• Microphone in/out
• Includes
3.5 mm jack
3.5 mm jack
Audio cable and AC adapter
9.4" x 2.1" x 8.2" / 239 x 54 x 208 mm
5W
• Dimension
• Power consumption
Description of the Controls
A. Bass button
Turn on or off to enhance the
Bass sound.
B. Power knob / Volume knob
If the picture has wavy patterns
when playing audio, reduce the
volume.Turn clockwise to
switch power on. Turning the
knob more will increase the
volume.
C. Headphone jack
Attach your headphones here.
The loudspeakers will
automatically switch off once
headphones are connected.
file:///D|/EDFU/crt_17/edoc/english/INSTALL_2/mm_pede/mm_inst.htm (1 of 4) [6/25/2003 10:09:58 AM]
6G3B11 Multimedia Base (option)
D. Microphone jack
Attach your microphone here.
E. Audio In
Connect this to the audio
output of your PC.
F. MIC Out
Connect this to the microphone
output of your PC.
G. DC Input
Connect power input here.
Installing your Multimedia Pedestal
1. To INSTALL
● Slide the pedestal, aligning with the holes on the
side.
● Then click the back hook into the corresponding
hole on the bottom plate of your monitor.
file:///D|/EDFU/crt_17/edoc/english/INSTALL_2/mm_pede/mm_inst.htm (2 of 4) [6/25/2003 10:09:58 AM]
6G3B11 Multimedia Base (option)
2. To UN-INSTALL
● Lift the back hook from the hole on the bottom
plate of your monitor.
● Slide out the pedestal the opposite direction (from
when you installed it).
Power adapter Installation
Installing the adapter
There are two (2) ways of installing the adapter
A. T-connector
B. Wall more connector
Monitor
T-connector
PC power cord.
Transformer
Power outlet
Multimedia Base
DC input
PC
Note:
Please keep
transformer away from
monitor as far as possible ( at
least 50 cm ) to avoid cansing unstable monitor picture.
file:///D|/EDFU/crt_17/edoc/english/INSTALL_2/mm_pede/mm_inst.htm (3 of 4) [6/25/2003 10:09:58 AM]
6G3B11 Multimedia Base (option)
file:///D|/EDFU/crt_17/edoc/english/INSTALL_2/mm_pede/mm_inst.htm (4 of 4) [6/25/2003 10:09:58 AM]
USB Hub (Optional Feature)
PCUH411 USB Hub (Option)
Installing your USB Hub
Installing on a
conventional base.
1. Take out the
USB hub from
the box.
2. Take off the USB
hub cover.
3. Slightly tilt and lift
the base of your
monitor.
4. Attach the USB
hub by clipping
into the base.
5. You can
reposition the
USB hub along
the base to suit
your needs.
Installing on the
Multimedia base.
Follow Steps 1 and 2
above.
6. Position the USB
hub to the back
file:///D|/EDFU/crt_17/edoc/english/INSTALL_2/usbhub/usb_inst.htm (1 of 2) [6/25/2003 10:09:58 AM]
USB Hub (Optional Feature)
of the Multimedia
Pedestal.
7. Attach the USB
hub by sliding-in
to the Multimedia
base.
file:///D|/EDFU/crt_17/edoc/english/INSTALL_2/usbhub/usb_inst.htm (2 of 2) [6/25/2003 10:09:58 AM]
The OSD Controls
The OSD Controls
BRIGHTNESS
To adjust your screen's brightness, follow the steps below. Brightness is the overall intensity of the light
coming from the screen. A 50% brightness is recommended.
1) Press the
or
button on the monitor. The BRIGHTNESS window appears.
2) Press the
or
button to adjust the brightness.
3) When the brightness is adjusted to the level desired, stop pressing the
or
button and after three
seconds the BRIGHTNESS window will disappear with the new adjustment saved.
After the BRIGHTNESS window has disappeared, to continue to the CONTRAST
window, follow the steps under CONTRAST.
Smart
Help
CONTRAST
To adjust your screen's contrast, follow the steps bellow. Contrast is the difference between the light and
dark areas on the screen. A 100% contrast is recommended.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (1 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
1) Press the
or
button on the monitor. The CONTRAST window appears.
2) Press the
or
button to adjust the contrast.
3) When the contrast is adjusted to the level desired, stop pressing the
or
button and after three
seconds the CONTRAST window will disappear with the new adjustment saved.
After the CONTRAST window has disappeared, to continue to the MAIN CONTROLS,
follow the steps under LANGUAGE
Smart
Help
LANGUAGE
The ON SCREEN DISPLAY shows its settings in one of eight languages. The default is English, but you
can select French, Spanish, German, Italian, Simplify-Chinese, Korea, or Brazilian Portuguese.
1) Press the
highlighted.
button on the monitor. The MAIN CONTROLS window appears. LANGUAGE should be
2) Press the
button again. The LANGUAGE window appears.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (2 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
3) Press the
or
button until the desired language is highlighted.
4) Press the
CONTROLS will be highlighted...
After returning to MAIN CONTROLS . . .
button to confirm your selection and return to MAIN CONTROLS window. CLOSE MAIN
. . . to continue to INPUT SIGNAL SELECTION, press the
button until INPUT
Smart
SIGNAL SELECTION is highlighted. Next, follow steps 3 - 5 under INPUT SIGNAL
SELECTION.
Help
. . . to exit completely, press the
button
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (3 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
ZOOM
ZOOM increases or decreases the size of the images on your screen. To adjust the ZOOM follow the steps
below.
1) Press the
2) Press the
button on the monitor. The MAIN CONTROLS window appears.
button until ZOOM is highlighted.
3) Press the
button. The ZOOM window appears.
4) Press the
or
button to adjust ZOOM.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (4 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
5) Press the
button to confirm your selection and return to the MAIN CONTROLS window. CLOSE
MAIN CONTROLS will be highlighted.
After returning to MAIN CONTROLS . . .
. . . to continue to ADJUST HORIZONTAL, press the
button until ADJUST
Smart
HORIZONTAL is highlighted. Next, follow steps 3 - 7 under ADJUST HORIZONTAL.
Help
. . . to exit completely, press the
button
ADJUST HORIZONTAL
ADJUST POSITION under ADJUST HORIZONTAL shifts the image on your screen either to the left or right.
Use this feature if your image does not appear centered. ADJUST SIZE under ADJUST HORIZONTAL
expands or controls the image on your screen, pushing it out toward the left and right sides or pulling it in
toward the center.
1) Press the
2) Press the
button on the monitor. The MAIN CONTROLS window appears.
button until ADJUST HORIZONTAL is highlighted.
3) Press the
button. The ADJUST HORIZONTAL window appears. POSITION should be highlighted.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (5 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
4) Press the
or
button to move the image to the left or right.
5) When the position is adjusted, press the
to highlight SIZE.
button to return to MAIN CONTROLS window, or press the
6) To adjust the horizontal size, press the
or
button.
7) When the size is adjusted, press the
CONTROLS will be highlighted.
button to return to MAIN CONTROLS window. CLOSE MAIN
After returning to MAIN CONTROLS . . .
. . . to continue to ADJUST VERTICAL, press the
button until ADJUST
Smart
VERTICAL is highlighted. Next, start with step 3 under ADJUST VERTICAL and follow
the directions.
Help
. . . to exit completely, press the
button
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (6 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
ADJUST VERTICAL
ADJUST POSITION under ADJUST VERTICAL shifts the image on your screen either up or down. Use this
feature if your image does not appear centered. ADJUST SIZE under ADJUST VERTICAL expands or
controls the image on your screen, pushing it out toward the top or bottom or pulling it in toward the center.
1) Press the
2) Press the
button on the monitor. The MAIN CONTROLS window appears.
button until ADJUST VERTICAL is highlighted.
3) Press the
button. The ADJUST VERTICAL window appears. POSITION should be highlighted.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (7 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
4) Press the
or
button to move the image up or down.
5) When the position is adjusted, press the
to highlight SIZE.
button to return to MAIN CONTROLS window, or press the
6) To adjust the vertical size, press the
or
button.
7) When the size is adjusted, press the
CONTROLS will be highlighted.
button to return to MAIN CONTROLS window. CLOSE MAIN
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (8 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
After returning to MAIN CONTROLS . . .
. . . to continue to ADJUST SHAPE, press the
button until ADJUST SHAPE is
Smart
highlighted. Next, start with step 3 under ADJUST SHAPE and follow the directions.
Help
. . . to exit completely, press the button
ADJUST SHAPE
ADJUST SIDE CURVE
ADJUST SIDE CURVE under ADJUST SHAPE allows you to adjust two of the five preset options. These
two options are PINCUSHION and BALANCED pincushion. Note: use these features only when the picture
is not square.
1) Press the
2) Press the
button on the monitor. The MAIN CONTROLS window appears.
button until ADJUST SHAPE is highlighted.
3) Press the
highlighted.
button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (9 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
4) Press the
button. The SIDE CURVE window appears. PINCUSHION should be highlighted.
5) To adjust the pincushion, press the
or
button.
6) When the pincushion is adjusted, press the
to return to the ADJUST SHAPE window.
button to highlight BALANCED or press the
button
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (10 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
7) To adjust the balanced pincushion, press the
or
button.
8) When the balanced pincushion is adjusted, press the
window. BACK TO MAIN WINDOWS will be highlighted.
button to return to the ADJUST SHAPE
9) Press the
button to return to the MAIN CONTROLS window, or press the
button until ADJUST
SIDE ANGLES is highlighted.
After returning to MAIN CONTROLS . . .
...to continue to ADJUST SIDE ANGLES, start with step 5 under ADJUST SIDE
ANGLES and follow the directions.
Smart
...to exit completely, press the
button twice.
Help
...to adjust only the BALANCED pincushion, follow steps 1 - 4 above, then press the
button, and follow steps 7 - 9.
ADJUST SIDE ANGLES
ADJUST SIDE ANGLES under ADJUST SHAPE allows you to adjust two of the five preset options. These
two options are TRAPEZOID and PARALLELOGRAM. Note: use these features only when the picture is not
square.
1) Press the
2) Press the
button on the monitor. The MAIN CONTROLS window appears.
button until ADJUST SHAPE is highlighted.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (11 of 25) [6/25/2003 10:10:05 AM]
The OSD Controls
3) Press the
highlighted.
button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be
4) Press the
5) Press the
button to highlight ADJUST SIDE ANGLES.
button. The SIDE ANGLES window appears. TRAPEZOID should be highlighted.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (12 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
6) To adjust the trapezoid, press the
or
button.
7) When the trapezoid is adjusted, press the
button to return to the ADJUST SHAPE window.
button to highlight PARALLELOGRAM or press the
8) To adjust the parallelogram, press the
or
button.
9) When the parallelogram is adjusted, press the
BACK TO MAIN WINDOWS will be highlighted.
button to return to the ADJUST SHAPE window.
10) Press the
button to return to the MAIN CONTROLS window, or press the
button until ROTATE
IMAGE is highlighted.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (13 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
After returning to MAIN CONTROLS . . .
...to continue to ROTATE IMAGE, start with step 5 under ROTATE IMAGE and follow
the directions.
Smart
...to exit completely, press the
button twice.
Help
...to adjust only the PARALLELOGRAM, follow steps 1 - 4 above, then press the
button, and follow steps 7 - 9.
ROTATE IMAGE (Not available in all models)
ROTATE IMAGE under ADJUST SHAPE allows you to adjust one of the five preset options. These two
options are PINCUSHION and BALANCED pincushion. Note: use this feature only when the picture is not
square.
1) Press the
2) Press the
button on the monitor. The MAIN CONTROLS window appears.
button until ADJUST SHAPE is highlighted.
3) Press the
highlighted.
button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be
arrow until ROTATE IMAGE is highlighted.
4) Press the
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (14 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
5) Press the
button. The ROTATE IMAGE window appears. ROTATE should be highlighted.
6) To adjust the rotation, press the
or
button.
7) When the rotation is adjusted, press the
MAIN CONTROLS should be highlighted.
button to return to the ADJUST SHAPE window. BACK TO
8) Press the
button to return to MAIN CONTROLS.
After returning to MAIN CONTROLS . . .
. . . to continue to ADJUST COLOR, press the
button until ADJUST COLOR is
Smart
highlighted. Next, start with step 3 under ADJUST COLOR and follow the directions.
Help
...to exit completely, press the
button twice.
ADJUST COLOR
Your monitor has three preset options you can choose from. The first option is for GENERAL USE, which is
fine for most applications. The second option is for IMAGE MANAGEMENT, which includes projects such as
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (15 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
desktop publishing, viewing a DVD from your DVD player or pictures on the World Wide Web, and playing
video games. The third option is for PHOTO RETOUCH, which is for working with pictures you have
imported into your computer and want to alter. When you select one of these options, the monitor
automatically adjusts itself to that option. There is also a fourth option, USER PRESET, which allows you to
adjust the colors on your screen to a setting you desire.
1) Press the
2) Press the
button on the monitor. The MAIN CONTROLS window appears.
button until ADJUST COLOR is highlighted.
3) Press the
button. The ADJUST COLOR window appears.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (16 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
4) Press the
or
button to highlight 9300K for GENERAL USE, 6500K for IMAGE MANAGEMENT,
5500K for PHOTO RETOUCH, or USER PRESET.
5) Once you have highlighted GENERAL USE, IMAGE MANAGEMENT, or PHOTO RETOUCH, press the
button to confirm you selection and return to the MAIN CONTROLS window. CLOSE MAIN
CONTROLS will be highlighted.
6a) If USER PRESET is highlighted, press the
button to highlight RED. Next, press the
button to highlight GREEN. Next, press the
or
button to adjust the color red.
6b) When finished with RED, press the
to adjust the color green.
or
button
6c) When finished GREEN, press the
adjust the color blue.
button to highlight BLUE. Next, press the
or
button to
6d) When all adjustments are complete, press the
button to confirm your adjustments and return to the
MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted.
After returning to MAIN CONTROLS. . .
. . . to continue to RESET TO FACTORY SETTINGS, press the
button until
Smart
RESET TO FACTORY SETTINGS is highlighted. Next, start with step 3 under RESET
TO FACTORY SETTINGS.
Help
. . . to exit completely, press the
button.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (17 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
RESET TO FACTORY SETTINGS
RESET TO FACTORY SETTINGS returns everything in all the windows to factory presets.
1) Press the
2) Press the
button on the monitor. The MAIN CONTROLS window appears.
button until RESET TO FACTORY SETTINGS is highlighted.
3) Press the
4) Press the
button. The RESET TO FACTORY SETTINGS window appears.
or
button to select YES or NO. NO is the default. YES returns all settings to their
original factory adjustments.
5) Press the
button to confirm your selection and return to the MAIN CONTROLS window. CLOSE
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (18 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
MAIN CONTROLS will be highlighted.
After returning to MAIN CONTROLS . . .
. . . to continue to EXTRA CONTROLS, press the
button until EXTRA
Smart
CONTROLS is highlighted. Next, start with step 3 under EXTRA CONTROLS.
Help
. . . to exit completely, press the
button.
EXTRA CONTROLS
DEGAUSS
EXTRA CONTROLS is a set of three features, including DEGAUSS. Degaussing removes electromagnetic
build up that may distort the color on your screen.
1) Press the
2) Press the
button on the monitor. The MAIN CONTROLS window appears.
button until EXTRA CONTROLS is highlighted.
3) Press the
button. The EXTRA CONTROLS window appears. MOIRE will be highlighted.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (19 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
4) Press the
button to highlight DEGAUSS.
5) To degauss your screen, press the
button. Your screen will be degaussed, then the MAIN
CONTROLS window will reappear. CLOSE MAIN CONTROLS will be highlighted.
After returning to MAIN CONTROLS . . .
. . . to continue to ADJUST MOIRE, press the
button until EXTRA CONTROLS is
Smart
highlighted. Next, start with step 3 under EXTRA CONTROLS, ADJUST MOIRE.
Help
. . . to exit completely, press the
button.
ADJUST MOIRE (Not available in all models)
EXTRA CONTROLS is a set of three features, including ADJUST MOIRE. Moire is a fringe pattern arising
from the interference between two superimposed line patterns. To adjust your moire, follow the steps below.
Note: Use only if necessary. By activating ADJUST MOIRE, sharpness can be affected.
1) Press the
button on the monitor. The MAIN CONTROLS window appears.
2) Press the DOWN CURSOR button until EXTRA CONTROLS is highlighted.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (20 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
3) Press the
button. The EXTRA CONTROLS window appears. ADJUST MOIRE will be highlighted.
4) Press the
button. The ADJUST MOIRE window appears. HORIZONTAL will be highlighted.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (21 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
5) To adjust the horizontal moire, press the
or
button.
6) When the horizontal moire is adjusted, press the
button to highlight VERTICAL.
7) To adjust the vertical moire, press the
or
button.
button to return to the EXTRA CONTROLS window.
8) When the vertical moire is adjusted, press the
BACK TO MAIN CONTROLS will be highlighted.
After returning to MAIN CONTROLS . . .
Smart
. . . to exit completely, press the
button.
Help
Turn on LightFrame (Not available in all models)
EXTRA CONTROLS is a set of three features, including LIGHTFRAME. This feature allows the user to turn
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (22 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
on the LIGHTFRAME function to activate in full screen mode.
1) Press
button on the monitor. The MAIN CONTROLS window appears.
button until EXTRA CONTROLS is highlight.
2) Press the
3) Press the
4) Press the
button. The EXTRA CONTROLS window appears. ADJUST MOIRE will be highlighted.
button until LIGHTFRAME is highlighted.
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (23 of 25) [6/25/2003 10:10:06 AM]
The OSD Controls
file:///D|/EDFU/crt_17/edoc/english/OSD/osd_cont.htm (25 of 25) [6/25/2003 10:10:06 AM]
F1rst Choice Warranty
Your Philips F1rst Choice Warranty
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and deliver
high-quality performance, ease of use and ease of installation. Should you encounter any
difficulties while installing or using this product, please contact the Philips helpdesk
directly to benefit from your Philips F1rst Choice Warranty. This three-year service
warranty entitles you to a swap model on-site if your monitor turns out to be faulty or
defective.Philips aims at a swap within 48 hours of your call being received.
What is covered?
The Philips F1rst Choice Warranty applies within Andorra, Austria, Belgium, Cyprus, Denmark, France,
Germany, Greece, Finland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, the Netherlands, Norway,
Portugal, Sweden, Switzerland, Spain and the United Kingdom and only for monitors originally designed,
manufactured, approved and/or authorized for usage within these countries.
Warranty coverage begins as from the day you buy your monitor. For three years thereafter, your monitor
will be swapped by at least an equivalent monitor in case of defects provided for under the warranty
coverage.
The swap monitor remains yours and Philips keeps the defective/original monitor. For the swap monitor the
warranty period remains equal to that of your original monitor, being 36 months as from the purchase date
of your original monitor.
What is excluded?
The Philips F1rst Choice Warranty applies provided the product is handled properly for its intended use, in
accordance with its operating instructions and upon presentation of the original invoice or cash receipt,
indicating the date of purchase, dealer's name and model and production number of the product.
The Philips F1rst Choice Warranty may not apply if:
● The documents have been altered in any way or made illegible;
● The model or production number on the product has been altered, deleted, removed or made
illegible;
● Repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
● Damage is caused by accidents including but not limited to lightning, water or fire, misuse or neglect;
● Reception problems caused by signal conditions or cable or antenna systems outside the unit;
● Defects caused by abuse or misuse of the monitor;
● Product requires modification or adaptation to enable it to comply with local or national technical
standards, which apply in countries for which the product was not originally designed, manufactured,
approved and/or authorized. Therefore always check whether a product can be used in a specific
country.
● Note that products that are not originally designed, manufactured, approved and/or authorized for
usage within the Philips F1rst Choice countries, do not apply to the Philips F1rst Choice Warranty. In
these cases the Philips global warranty terms are valid.
Just a phone call away
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/war_1st.htm (1 of 2) [6/25/2003 10:10:11 AM]
F1rst Choice Warranty
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions carefully
before contacting the Philips helpdesk.
To solve your problem quickly, please prepare the following details before contacting the Philips helpdes
● Philips type number
● Philips serial number
● Purchase date (copy of purchase may be required)
● PC environment Processor:
o 286/386/486/Pentium Pro/Internal memory
o Operating system (Windows, DOS, OS/2, MAC)
o Fax/Modem/Internet program?
● Other cards installed
Having the following information available will also help speed up the process:
● Your proof of purchase indicating: date of purchase, dealer name, model and product serial number.
● The full address to which the faulty monitor has to be collected and the swap model should be
delivered.
Philips' customer help desks are located worldwide. You can contact Philips Monday - Friday from 08.00 -
20.00 hrs Central European Time (CET) and on Saturdays and Sundays from 10.00 to 18.00 hrs CET by
using one of the helpdesk telephone numbers. Click here to access the F1rst Choice Contact Information.
Or you can reach us via:
Website:http://www.philips.com
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/war_1st.htm (2 of 2) [6/25/2003 10:10:11 AM]
International Guarantee
Your International Guarantee
Dear Customer,
Thank you for purchasing this Philips product which has been designed and manufactured to the highest
quality standards.
If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and
replacement parts irrespective of the country where it is repaired during a period of 12 months from date of
purchase. This international Philips guarantee complements the existing national guarantee obligations to
you of dealers and Philips in the country of purchase and does not affect your statutory rights as a
customer.
The Philips guarantee applies provided the product is handled properly for its intended use, in accordance
with its operating instructions and upon presentation of the original invoice or cash receipt, indicating the
date of purchase, dealer's name and model and production number of the product.
The Philips guarantee may not apply if:
● the documents have been altered in any way or made illegible;
● the model or production number on the product has been altered, deleted, removed or made illegible;
● repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
● damage is caused by accidents including but not limited to lightning, water or fire, misuse or neglect.
Please note that the product is not defective under this guarantee in the case where modifications become
necessary in order for the product to comply with local or national technical standards which apply in
countries for which the product was not originally designed and/or manufactured. Therefore always check
whether a product can be used in a specific country.
In case your Philips product is not working correctly or is defective, please contact your Philips dealer. In the
event you require service whilst in another country a dealer address can be given to you by the Philips
Consumer Help Desk in that country, the telephone and fax number of which can be found in the relevant
part of this booklet.
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions carefully
before contacting your dealer. If you have questions which your dealer cannot answer or any related
Website: http://www.philips.com
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/war_intl.htm [6/25/2003 10:10:11 AM]
United States Guarantee
LIMITED WARRANTY(Computer Monitor)
Click here to access the Warranty Registration Card
One Year Exchange*
*Product will be exchanged with a new or renewed to original specifications unit within two business
days for the first year.
WHO IS COVERED?
You must have proof of purchase to receive warranty service. A sales receipt or other document showing
that you purchased the product as new is considered proof of purchase.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product. For one year thereafter, all parts will be repaired
or replaced, and labor is free. All parts, including repaired and replaced parts, are covered only for the
original warranty period. When the warranty on the original product expires, the warranty on all replaced
and repaired products and parts also expires.
WHAT IS EXCLUDED?
Your warranty does not cover:
● labor charges for installation or setup of the product, adjustment of customer controls on the
product, and installation or repair of systems outside of the product.
● product repair and/or part replacement because of misuse, accident, unauthorized repair or
other cause not within the control of Philips Consumer Electronics.
● a product that requires modification or adaptation to enable it to operate in any country other
than the country for which it was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications.
● incidental or consequential damages resulting from the product. (Some states do not allow the
exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
This includes, but is not limited to, prerecorded material, whether copyrighted or not
copyrighted.)
● a product used for commercial or institutional purposes.
● A product that has been modified from the original design.
Where IS SERVICE AVAILABLE?
Warranty service is available in all countries where the product is officially distributed by Philips
Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the
product, the local Philips service organization will attempt to provide service (although there may be
a delay if the appropriate spare parts and technical manual(s) are not readily available).
Where CAN I GET MORE INFORMATION and HOW CAN I OBTAIN SERVICE?
For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A.
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/7sxWAR_USA.HTM (1 of 3) [6/25/2003 10:10:11 AM]
United States Guarantee
customers only) or (402) 536-4171.
Before Requesting Service...
Please check your owner's manual before requesting service. Adjustments of the controls discussed
there may save you a service call.
TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...
Contact the Philips Customer Care Center phone number listed below for product assistance and
procedures for servicing:
Philips Customer Care Center
(877) 835-1838 or (402) 536-4171
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties
of merchantability and fitness for a particular purpose, are limited in duration to the duration of this
express warranty. But, because some states do not allow limitations on how long an implied warranty
may last, this limitation may not apply to you.)
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
(800) 479-6696
One year free parts and one year free labor will be provided at Philips Canada depot or any one of its
authorized service centers.
REMEMBER... Please record the model and serial numbers found on the product below.
MODEL # ________________________________________________
SERIAL # ________________________________________________
This warranty gives you specific legal rights. You may have other rights which vary from
state/province to state/province.
Philips Customer Care Center, P. O. Box 2976, Longview, TX 75601
Your International Philips F1rst Choice Warranty
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and deliver high-quality
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/7sxWAR_USA.HTM (2 of 3) [6/25/2003 10:10:11 AM]
United States Guarantee
performance, ease of use and ease of installation. Should you encounter any difficulties while
installing or using this product, please contact Philips directly to benefit from your Philips F1rst
Choice Warranty. This one-year service warranty entitles you to a swap model on-site within 48
hours of your call being received within the first year of purchase. If you have any problems with
your monitor within the second or third year of purchase, we will repair it after it has been sent to the
service provider at your expense and returned to you within five working days, free of charge.
An extended warranty called Philips F1rst Choice Premium is available in addition to your Philips
F1rst Choice warranty. For more details contact your Philips dealer.
Before contacting Philips, please prepare the following details so we can solve your problem quickly.
● Philips type number
● Philips serial number
● Purchase date (copy of purchase may be required)
● PC environment Processor:
❍ 286/386/486/Pentium Pro/Internal memory
❍ Operating system (Windows, DOS, OS/2, MAC)
❍ Fax/Modem/Internet program?
● Other cards installed
Having the following information available will also help speed up the process:
● Your proof of purchase indicating: date of purchase, dealer name, model and product serial
number.
● The full address to which the swap model should be delivered.
Philips warranty applies provided the product is handled properly for its intended use.
Philips warranty will not apply if it appears during the repair process that:
- the reported failure is caused by improper handling or accidents
- the monitor is not defective and is within the specification
- the monitor has been altered or repaired by non authorised persons
If warranty claims are determined to be invalid, Philips may invoice the customer for all related
repair, verification and transportation costs.
Just a phone call away
Philips customer help desks are located worldwide. You can contact Philips Monday - Friday from
08.00 - 20.00 hrs Central European Time (CET) and on Saturdays and Sundays from 10.00 to 18.00
hrs CET by using one of the toll-free numbers. Click here to access the F1rst Choice Contact
Information. Or you can reach us via:
Website: http://www.philips.com
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/7sxWAR_USA.HTM (3 of 3) [6/25/2003 10:10:11 AM]
United States Guarantee
LIMITED WARRANTY (Computer Monitor)
Click here to access the Warranty Registration Card
Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange*
*Product will be exchanged with a new or renewed to original specifications unit within two business days
for the first year. This product must be shipped in at your expense for service during years two and three.
WHO IS COVERED?
You must have proof of purchase to receive warranty service. A sales receipt or other document showing
that you purchased the product is considered proof of purchase. Attach it to this owner's manual and keep
both nearby.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product. For three years thereafter, all parts will be
repaired or replaced, and labor is free. After three years from the day of purchase, you pay for the
replacement or repair of all parts, and for all labor charges.
All parts, including repaired and replaced parts, are covered only for the original warranty period. When the
warranty on the original product expires, the warranty on all replaced and repaired products and parts also
expires.
WHAT IS EXCLUDED?
Your warranty does not cover:
● labor charges for installation or setup of the product, adjustment of customer controls on the product,
and installation or repair of antenna systems outside of the product.
● product repair and/or part replacement because of misuse, accident, unauthorized repair or other
cause not within the control of Philips Consumer Electronics.
● reception problems caused by signal conditions or cable or antenna systems outside the unit.
● a product that requires modification or adaptation to enable it to operate in any country other than the
country for which it was designed, manufactured, approved and/or authorized, or repair of products
damaged by these modifications.
● incidental or consequential damages resulting from the product. (Some states do not allow the
exclusion of incidental or consequential damages, so the above exclusion may not apply to you. This
includes, but is not limited to, prerecorded material, whether copyrighted or not copyrighted.)
● a product used for commercial or institutional purposes.
Where IS SERVICE AVAILABLE?
Warranty service is available in all countries where the product is officially distributed by Philips Consumer
Electronics. In countries where Philips Consumer Electronics does not distribute the product, the local
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/WAR_USA.HTM (1 of 3) [6/25/2003 10:10:11 AM]
United States Guarantee
Philips service organization will attempt to provide service (although there may be a delay if the appropriate
spare parts and technical manual(s) are not readily available).
Where CAN I GET MORE INFORMATION?
For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A.
customers only) or (402) 536-4171.
Before Requesting Service...
Please check your owner's manual before requesting service. Adjustments of the controls discussed there
may save you a service call.
TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...
Contact the Philips Customer Care Center phone number listed below for product assistance and
procedures for servicing:
Philips Customer Care Center
(877) 835-1838 or (402) 536-4171
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties of
merchantability and fitness for a particular purpose, are limited in duration to the duration of this express
warranty. But, because some states do not allow limitations on how long an implied warranty may last, this
limitation may not apply to you.)
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
(800) 479-6696
Three years free parts and three years free labor will be provided at Philips Canada depot or any one of its
authorized service centers.
(In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed or
implied, including any implied warranties of merchantability or fitness for a particular purpose. Philips is not
liable under any circumstances for any direct, indirect, special, incidental or consequential damages,
howsoever incurred, even if notified of the possibility of such damages.)
REMEMBER... Please record the model and serial numbers found on the product below.
MODEL # ________________________________________________
SERIAL # ________________________________________________
This warranty gives you specific legal rights. You may have other rights which vary from state/province to
state/province.
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/WAR_USA.HTM (2 of 3) [6/25/2003 10:10:11 AM]
United States Guarantee
Philips Customer Care Center, P. O. Box 2976, Longview, TX 75601
Your International Philips F1rst Choice Warranty
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and deliver
high-quality performance, ease of use and ease of installation. Should you encounter
any difficulties while installing or using this product, please contact Philips directly to
benefit from your Philips F1rst Choice Warranty. This three-year service warranty
entitles you to a swap model on-site within 48 hours of your call being received
within the first year of purchase. If you have any problems with your monitor within
the second or third year of purchase, we will repair it after it has been sent to the
service provider at your expense and returned to you within five working days, free of
charge.
An extended warranty called Philips F1rst Choice Premium is available in addition to your Philips F1rst
Choice warranty. For more details contact your Philips dealer.
Before contacting Philips, please prepare the following details so we can solve your problem quickly.
● Philips type number
● Philips serial number
● Purchase date (copy of purchase may be required)
● PC environment Processor:
❍ 286/386/486/Pentium Pro/Internal memory
❍ Operating system (Windows, DOS, OS/2, MAC)
❍ Fax/Modem/Internet program?
● Other cards installed
Having the following information available will also help speed up the process:
● Your proof of purchase indicating: date of purchase, dealer name, model and product serial number.
● The full address to which the swap model should be delivered.
Just a phone call away
Philips’ customer help desks are located worldwide. You can contact Philips Monday - Friday from 08.00 -
20.00 hrs Central European Time (CET) and on Saturdays and Sundays from 10.00 to 18.00 hrs CET by
using one of the toll-free numbers. Click here to access the F1rst Choice Contact Information. Or you can
reach us via:
Website: http://www.philips.com
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/WAR_USA.HTM (3 of 3) [6/25/2003 10:10:11 AM]
F1rst Choice Contact Information
F1rst Choice Contact Information
Telephone numbers:
Austria
Belgium
Cyprus
Denmark
France
Germany
Greece
Finland
Ireland
01 546 575 603
02 275 0701
800 92256
35 25 87 61
03 8717 0033
0696 698 4712
00800 3122 1223
09 2290 1908
01 601 1161
Italy
02 48 27 11 53
408 443 5501
053 482 9800
22 70 82 50
Luxembourg
The Netherlands
Norway
Portugal
0800 831 363
08 632 0016
Sweden
Switzerland
Spain
02 23 10 21 16
09 17 45 62 46
0207 949 0069
877 835 1838
United Kingdom
U.S.A.
* Calls charged at local
rates
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/WARFIRST.HTM [6/25/2003 10:10:19 AM]
Consumer Information Centers
Consumer Information Centers
Eastern Europe
CZECH REPUBLIC
Philips Service
V Mezihorí 2180 00 Prague
Phone: (02)-6831581
Fax : (02)-66310852
HUNGARY
Philips Markaszerviz.
Kinizsi U 30-36Budapest 1092
Phone: (01)-2164428
Fax : (01)-2187885
POLAND
Philips Polska CE
UL.Marszalkowska 45/49
00-648 Warszawa
Phone: (02)-6286070
Fax : (02)-6288228
RUSSIA
Philips Representation Office
Ul. Usacheva 35a
119048 Moscow
Phone: 095-937 9300
TURKEY
Türk Philips Ticaret A.S.
Talatpasa Caddesi No 5.
80640-Gültepe/Istanbul
Phone: (0800)-211 40 36
Fax : (0212)-281 1809
Latin America
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.htm (1 of 9) [6/25/2003 10:10:26 AM]
Consumer Information Centers
ANTILLES
Philips Antillana N.V.Kaminda A.J.E. Kusters 4
Zeelandia, P.O. box 3523-3051
Willemstad, Curacao
Phone: (09)-4612799
Fax : (09)-4612772
ARGENTINA
Vedia 3892 Capital Federal
CP:1430 Buenos Aires
Phone: (011)-4544 2047
Fax: (011)-4544 2928
BRASIL
Philips da Amazonia Ind. Elet.Ltda.
Av.Luis Carlos Berrini,
1400-Sao Paulo-SP
Phone: 0800-7010-203
CHILE
Philips Chilena S.A.
Avenida Santa Maria 0760
P.O. box 2687Santiago de Chile
Phone: (02)-730 2000
Fax : (02)-777 6730
COLOMBIA
Industrias Philips de Colombia
S.A.-Division de Servicio
CARRERA 15 Nr. 104-33
Bogota, Colombia
Phone: (01)-8000-111001 (toll free)
Fax : (01)-619-4300/619-4104
MEXICO
Consumer Information Centre
Norte 45 No.669
Col. Industrial Vallejo
C.P.02300, -Mexico, D.F.
Phone: (05)-3687788 / 9180050462
Fax : (05)-7284272
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.htm (2 of 9) [6/25/2003 10:10:26 AM]
Consumer Information Centers
PARAGUAY
Philips del Paraguay S.A.
Avenida Artigas 1513
Casilla de Correos 605
Asuncion
Phone: (021)-211666
Fax : (021)-213007
PERU
Philips Peruana S.A.
Customer Desk
Comandante Espinar 719
Casilla 1841
Limab18
Phone: (01)-2136200
Fax : (01)-2136276
URUGUAY
Ind.Philips del Uruguay S.A.
Lius Alberto de Herrera 1248-P:10
Customer Help Desk 11300 Montevideo
Phone: (02)-6281111
Fax : (02)-6287777
VENEZUELA
Industrias Venezolanas Philips S.A.
Apartado Postal 1167
Caracas 1010-A
Phone: (02) 2377575
Fax : (02) 2376420
Canada
CANADA
Philips Electronics Ltd.
281 Hillmount Road Markham Ontario,
L6C 2S3
Phone: 800- 479-6696
Fax:905-887-3974
Pacific
AUSTRALIA
Philips Consumer Service.
Customer Information Centre.
3 Figtree Drive
Homebush Bay NSW 2140
Phone: CIC:1300 363 391, PCE Service:1 300-361 392
Fax:+61 2 9947 0063
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.htm (3 of 9) [6/25/2003 10:10:26 AM]
Consumer Information Centers
NEW ZEALAND
Philips New Zealand Ltd.
Consumer Help Desk
2 Wagener Place, Mt.Albert
P.O. box 1041
Auckland
Phone: 0800 477 999 (Toll Free)
Fax:0800 288 588
Asia
BANGLADESH
Philips Service Centre
100 Kazi Nazrul Islam
Avenue Kawran Bazar C/A
Dhaka-1215
Phone: (02)-812909
Fax : (02)-813062
CHINA
SHANHAI
No. 1102 wuding road, jing an district,
200040 Shanghai,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
NANJING
No. 12-2 dong da ying bei, zhu jiang road,
210018 Nanjing,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
HANGZHOU
No. 20 jiao gong road,
310012 Hangzhou,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
BEIJING
No. 171-3 hai dian road, hai dian district,
100086 Beijing,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
SHENYANG
No. 84-1 san hao street,
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.htm (4 of 9) [6/25/2003 10:10:26 AM]
Consumer Information Centers
110003 Shenyang
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
XIAN
No. 6-9 yan ta road south part,
710061 Xian,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
GUANGZHOU
No. 15-17 long kou dong road, tian he district,
510070 Guangzhou,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
SHENZHEN
Room 603, electronic BLD, No. 30 Shen nan zhong road,
518031 Shenzhen,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
CHANGSHA
Room 18, He yi computer city, chao yang road,
Changsha,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
WUHAN
No. 60-66 gui yuan road, hong shan district,
430070 Wuhan,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
CHENGDU
Chengdu Sience-technolege university service BLD, No. 24 nan yi duan of
Yi huan road,
410061 Chengdu,
P.R. China
Phone: 800 820 5128 (Toll Free)
Fax:21-65610647
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.htm (5 of 9) [6/25/2003 10:10:26 AM]
Consumer Information Centers
HONG KONG
Philips Hong Kong Limited
Consumer Information Centre
16/F Hopewell Centre
17 Kennedy Road, WANCHAI
Phone: 2619-9663
Fax: 2481 5847
INDIA
BOMBAY
Philips India
Customer Relation Centre
Bandbox House
254-D Dr. A Besant Road, Worli
Bombay 400 025
Phone: (020)-712 2048 ext 2765
Fax:(020)-712 1558
CALCUTTA
Customer Relation Centre
7 justice Chandra Madhab Road
Calcutta 700 020
Phone: (020)-712 2048 ext 2765
Fax:(020)-712 1558
MADRAS
Customer Relation Centre
3, Haddows Road
Madras 600 006
Phone: (020)-712 2048 ext 2765
Fax:(020)-712 1558
NEW DELHI
Customer Relation Centre
68, Shivaji Marg
New Dehli 110 015
Phone: (020)-712 2048 ext 2765
Fax:(020)-712 1558
INDONESIA
Philips Group of Companies in Indonesia
Consumer Information Centre
Jl.Buncit Raya Kav. 99-100
12510 Jakarta
Phone: (021)-7940040/7984255 Ext 1612
Fax : (021)-7947511 / 7947539
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.htm (6 of 9) [6/25/2003 10:10:26 AM]
Consumer Information Centers
JAPAN
Philips Consumer Electronics
1-11-9,Ebisuminami
Shibuya-Ku
Tokyo 150
Phone: (03)-3719-2235
Fax : (03)-3715-9992
KOREA
Philips Korea Ltd.
Philips House
C.P.O. box 3680
260-199, Itaewon-Dong.
Yongsan-Ku, Seoul 140-202
Phone: 080 600 6600 (Toll Free)
Fax:(02)709 1245
MALAYSIA
Philips Malaysia Sdn. Berhad
Service Dept.
No.51,sect.13 Jalan University.
46200 Petaling Jaya, Selagor.
P.O.box 12163
50768 Kuala Lumpur.
Phone: (03)-7950 5501/02
Fax:(03)-7954 8504
PAKISTAN
KARACHI
Philips Electrical Ind. of Pakistan
Consumer Information Centre
F-54, S.I.T.E, P.O.Box 7101
75730 KARACHI
Phone: (021)-773 1927
Fax:(021)-772 1167
Philips Consumer Service Centre
168-F, Adamjee Road
Rawalpindi Cantt
Phone: (021)-773 1927
Fax:(021)-772 1167
PHILIPPINES
Philips Electronics and Lighting Inc.
106 Valero St., Salcedo Village
Makati, Metro Manilla.
Phone: (02)-888 0572 , Domestic Toll Free:1-800-10-PHILIPS or 1-800-10-744 5477
Fax:(02)-888 0571
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.htm (7 of 9) [6/25/2003 10:10:26 AM]
Consumer Information Centers
SINGAPORE
Philips Singapore Private Ltd.
Consumer Service Dept.
Lorong 1,Toa Payoh., P.O. box 340
Singapore 1231
Phone:6882 3999
Fax:6250 8037
TAIWAN
Philips Taiwan Ltd.
Consumer Information Centre
26F, 66, Chung-Hsiao W. Road, Sec. 1
Taipei, Taiwan
Phone: (02)-2382-4567 ,0800-231-099
Fax:(02)2382-3027
THAILAND
Philips Electronics (Thailand) Ltd.
Philips Service Centre
209/2 Sanpavut Road,
Bangna, Bangkok 10260
Phone : (02)-652 8652
Fax:(02)-614 3531
Africa
MOROCCO
Philips Electronique Maroc
304,BD Mohamed V
Casablanca
Phone: (02)-302992
Fax : (02)-303446
SOUTH AFRICA
South African Philips.
S.V. Div. 195 Main R.D.
Martindale., Johannesburg
P.O.box 58088
Newville 2114
Phone: (011)-4715000
Fax : (011)-4715020
Middle East
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.htm (8 of 9) [6/25/2003 10:10:26 AM]
Consumer Information Centers
DUBAI
Philips Middle East B.V.
Consumer Information Centre
P.O.Box 7785
DUBAI
Phone: (04)-3353666
Fax : (04)-3353999
EGYPT
Philips Egypt
Consumer Information Centre
10, Abdel Rahman El Rafei
Mohandessin - Cairo, P.O.Box 242
DOKKI
Phone: (02)-3313993
Fax : (02)-3492142
file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.htm (9 of 9) [6/25/2003 10:10:26 AM]
PHILIPS Warranty Card
8/16/02 12:38 PM Page 1
It Takes Only A Moment To
PROTECT YOUR INVESTMENT.
Congratulations on investing in a Philips product. It’s an important and intelligent decision that’s sure to reward you
for many years to come. To ensure you’ll get all of the privileges and protection that come with your purchase,
please complete your Warranty Registration Card within the next ten days.
SIMPLY MAIL THE CARD BELOW TO RECEIVE ALL
OF THESE BENEFITS TO WHICH YOU’RE ENTITLED.
WARRANTY VERIFICATION
Your prompt registration verifies your right to protection
under the terms and conditions of your warranty.
OWNER CONFIRMATION
Your completed Warranty Registration Card serves as confirmation
of ownership in the event of product loss or theft.
MODEL REGISTRATION
Returning the attached card right away guarantees you’ll receive
all information and special offers for which your purchase makes you eligible. So please act today!
www.philipsusa.com
DETACH AND MAIL PORTION BELOW.
WARRANTY
REGISTRATION CARD
Registering your product is an essential step to ensure that you receive all of the benefits you are entitled to as a
Philips customer. So complete the information below in ink, and drop this card in the nearest mailbox.
IMPORTANT - RETURN WITHIN TEN DAYS
Month
Day
Year
Mail This Card Today To Get The Most From Your Purchase!
No, I do not want to receive personalized offers about Philips products or other information from Philips in the future.
❏
3135 015 07803
rev. 7/02
PHILIPS Warranty Card
8/16/02 12:38 PM Page 2
! 1 3 7 5 4 1 5 3 3 8 !
D E P O S I T N Y 1 3 7 5 4 - 1 5 3 3
P O B O X 1 5 3 3
P r o m p t l y
P l e a s e O
M A T E
T I M E -
S T A M P
C L A S S
A P P L Y F I R S T
P L E A S E
a
IMPORTANT
Warranty
Registration Card
RETURN THE ATTACHED CARD WITHIN
TEN DAYS TO ENSURE YOUR:
✓ Warranty Verification
✓ Owner Confirmation
See Inside For
✓ Model Registration
Valuable
Benefits!
|