Mustek LM 3000 User Manual

LM-3000 LCD MONITOR  
USER’S MANUAL  
I. OVERVIEW  
LM-3000 is a highly luminant with low shadow effect 12.1” LCD  
monitor. It is economical of pace and provides broad display area  
almost compatible to that of a 14” CRT monitor for PC application.  
II. PACKAGE CONTENTS  
· LCD PANEL WITH CABLE INSTALLED  
· VGA ADAPTOR CARD – PST032  
· DRIVER UTILITY  
· THIS MANUAL  
III. LCD PANEL INSTALLATION  
The LM-3000 LCD panel is delivered with a separate base. The user  
has to find a surface which is horizontal and flat enough to place the  
LCD panel with its supporting base on. Please always manage to  
keep the installation site away from possibility of falling, shock,  
vibration, direct sun light, heavy dust, high temperature or high  
humidity etc.. The user should first take the pivot on the base out and  
insert the bottom part of the LCD panel into the opening of the base  
till it clicks. The user shall then fasten the pivot back to its position  
and the LCD panel is ready for cable connection.  
LM-3000 USER’S MANUAL - page 1  
IV. DISPLAY ADAPTOR CARD INSTALLATION  
U6  
U7  
U4  
U5  
J2  
U1  
U3  
U8  
J1  
U2  
The attached PST032 is a PCI bus SVGA adaptor card which offers a  
50 pin SCSI type connector for LM-3000 (Do not connect any  
device other than the LM-3000 LCD monitor to this port even if  
it was using a SCSI connector!) and a 3 x 5 D sub connector for  
external SVGA monitor. The user shall always first turn off the  
power to the PC and all its connected peripherals and disconnect all  
cables connected to the PC and then open the case of PC according to  
relevant instructions. The original VGA adaptor of the PC should be  
dismounted if there is one. Insert the PST032 into a proper PCI slot  
and restore everything else but the original VGA adaptor according to  
the instructions applicable to the PC. The PC will be ready for  
turning power on after the cable connections described below  
completed.  
LM-3000 USER’S MANUAL - page 2  
V. CABLE CONNECTION  
Attention : Never connect the cable while power on!  
The cable length is 1.5 M, that allows the user to arrange the LM-  
3000 at any place within this range from the PC. At one end of the  
cable attached is a SCSI 50 pin connector, at the other end, the  
connections are already installed to the rear of the LCD panel. Route  
the cables via the rear part of the base and clip them to the grooves to  
ensure that no excess strain passes to the cable connection to the  
panel. The user shall first press the two springs of the 50 pin SCSI  
type connector then connect the connector to the SVGA adaptor card  
and latch the connector.  
LM-3000 USER’S MANUAL - page 3  
VI. UTILITY INSTALLATION  
A.For Windows 3.1  
The drivers for Windows 3.1 are delivered in a separate 3.5”  
floppy diskette with the LCD monitor. To install the drivers for  
Windows 3.1 with the LCD monitor, the user should make sure that  
the Windows 3.1 is running properly using standard VGA driver.  
1. Select the MAIN group in Program Manager.  
2. Click on FILE or press ALT + F.  
3. Click on RUN or press R to select command line.  
4. Type in “A:\SETUP” with the diskette containing drivers for  
Windows 3.1 inserted in FDD A: (if it is in B: drive, type in  
“B:SETUP” instead), and then press ENTER.  
5. Choose for the language applicable.  
6. Press any key when being asked of confirmation to start  
installation.  
7. Press “ENTER” twice and then press the “END” key to input  
the directory to store drivers.  
8. Replace the command line “C:\WINDOWS” with the actual  
directory of the Windows files if they are not in the directory  
C:\WINDOWS. Then press ENTER.  
9. Press ESC key followed by Y key to finish the first stage of  
installation.  
10. To make the installed drivers effective, following procedures  
have to be taken out.  
11. Select MAIN group in Program Manager again.  
12. Select Windows Setup.  
13. Click on Options or press ALT + O.  
14. Click on Change System Settings or press C.  
15. Click on Display or press ALT + D.  
16. Select the intended video driver of proper resolution and  
colors then press ENTER. The names of the video drivers  
LM-3000 USER’S MANUAL - page 4  
start with CHIPS followed by either the number 65550 or  
6555X then followed by the matrix of resolution and colors.  
17. Select Restart Windows to make the selected driver effective.  
B.For Windows 95  
The following describes normal display driver installation  
procedures for Windows 95. Use these procedures when installing  
the display drivers provided in the directory for Windows 95. The  
drivers are stored in the subdirectory named WIN95 in the diskette.  
Click “Start”, then “Settings”, then “Control Panel”.  
Start the object "Display".  
Select the page of "Settings", and click the "Change Display Type"  
button.  
Choose the "Change" button in the "Adapter Type" area.  
Select the "Have Disk" button and press "OK".  
Specify the path to the new driver and press the <ENTER> key:  
Example 1: Insert the drivers disk in the A: floppy drive, and enter  
A:\WIN95.  
Example 2: Type in the name of the directory where you copied the  
drivers, either on your local hard drive or on a network  
share.  
Example 3: If you're not sure exactly where the drivers are, choose  
the "Browse..." button to find them.  
The "Select Device" dialog box will appear. Select the adapter that  
corresponds to the one you installed in your machine and click OK.  
Windows 95 will copy the display drivers to the proper directories  
on your system.  
Continue choosing Close until asked to restart your machine from the  
"Systems Settings Change" dialog box.  
After the system has restarted, you can go back into the Display  
applet and select alternate screen resolutions and color depths.  
LM-3000 USER’S MANUAL - page 5  
C.For Windows NT 3.5x  
The drivers for Windows NT of versions 3.5x are stored in a  
subdirectory named NT35 in the diskette.  
1. Run Windows NT Setup from Main Group  
2. Choose Option from the menu (Alt-O)  
3. Select Change system setting (Alt-C)  
4. Choose "Other" under display section  
5. Insert display driver disk in appropriate floppy drive  
D.For Windows NT 4.0  
The drivers for Windows NT of versions 4.0 are stored in a  
subdirectory named NT40 in the diskette.  
Step 1: Install Windows NT as you normally would for a VGA  
display.  
First click the Start button, go to Settings and click on Control Panel.  
Choose the Display icon and click on the icon. In the Display  
Properties window, click on the Settings tab. Then click on Change  
Display Type. In the Change Display Type window, click on the  
Change button under Adapter Type. This will bring up the Select  
Device window.  
Step 2: In the Select Device window, click on the Other button.  
Enter source directory where the Windows NT driver files are  
located.  
Press <ENTER> and the name of the Chips and  
Technologies Video Accelerator driver will appear at the end of  
Models list box. Scroll to the end of the list box and double click on  
the driver. Once the installation is complete, the system must be shut  
down and restarted.  
LM-3000 USER’S MANUAL - page 6  
Step 3: Upon restart, select the desired display settings from the  
Display property dialog box. Click on Test to test the newly selected  
graphics mode. A color test screen should appear, followed by the  
Testing Mode window. Click on Yes to continue. The Display  
Settings Change window will appear. Click on Restart Now for the  
new settings to take effect.  
VII. CONTROL AND ADJUSTMENT  
· Horizontal slide : The panel can be pushed left or right to slide  
without moving the base through a distance of  
36 mm each side.  
· Swivel :  
The panel can be horizontally rotated, using the  
pivot on the base, 45° each way.  
· Tilt :  
The panel can be folded backward from the  
upstraight porition to nearly horizontal  
position, total range is 85°.  
· Brightness :  
On the rear side of the LCD display panel,  
there are two control knobs to control the  
picture displayed. The left one (as viewed from  
the rear side) marked as  
controls the  
brightness of the picture. Turning it clockwise  
as viewed from the rear side will increase the  
brightness of the picture, and turning it counter  
clockwise will decrease the brightness.  
· Contrast :  
The other one marked “ ” located to the right  
as viewed from the rear side controls the  
contrast of the picture. Turning it clockwise as  
viewed from the rear side will increase the  
contrast of the picture, and turning it counter  
clockwise will decrease the contrast.  
LM-3000 USER’S MANUAL - page 7  
Tilt  
Brightness control knob  
Contrast  
control knob  
Swivel  
LM-3000 USER’S MANUAL - page 8  
VIII.SPECIFICATION  
MODEL:  
LM-3000  
Panel:  
12.1 ” DSTN COLOR  
SVGA 800 x 600  
247.02 (W) x 185.76 (H) mm  
250 ms  
SIDE-EDGE TYPE CFL x 2 TUBES  
NON-GLARE TREATMENT  
0.0821 (W) x 0.2863 (H) mm  
0.2021 (W) x 0.3063 (H) mm  
150 cd/m2  
Max. Resolution:  
Effective Display Area:  
Response Time:  
Backlight:  
Polarizer:  
Dot Size:  
Dot Pitch:  
Brightness:  
Operating Temperature: 0°C ~ 40°C  
Storage Temperature:  
Operating Humidity:  
Storage Humidity:  
-20°C ~ 60°C  
10% ~ 85%RH, non-condensation  
for Temp £ 40°C, 10% ~ 85%RH, non-  
condensation  
for Temp > 40°C, Absolute humidity  
shall be less than 85%RH at 40°C  
25,000 hrs  
Back Light Reliability:  
Control Card (W/Power): PST032  
Control Card Bus Type:  
Video Memory Size:  
PCI  
1 MB  
Display Mode Supported: UP TO HIGH COLOR @ 800 x 600  
Cable Length:  
External Control:  
Swivel Range:  
Tilt Range:  
Slide Range:  
Total Width:  
Total Depth:  
Total Height:  
1.5m  
CONTRAST; BRIGHTNESS  
Left 45° and right 45°  
Stand straight (as 0°) to backward 85°  
Left 36 mm and right 36 mm  
300 mm  
188 mm  
251 mm  
LM-3000 USER’S MANUAL - page 9  
DISCLAIMER  
The manufacturer of the LCD display system makes no representations or warranties, either  
expressed or implied, by or with respect to anything in this manual, and shall not be liable for any  
implied warranties of fitness for a particular purpose or for any indirect, special or consequential  
damages. Information in this document is subject to change without notice and does not represent a  
commitment on behalf of the manufacturer.  
LM-3000 USER’S MANUAL - page 10  

HP Hewlett Packard t5135 User Manual
IBM All in One Super7 Single Board Computer PCM 5896 User Manual
Intel IM Q35 Series User Manual
JVC AV 21BX16 User Manual
Korg D1200MKII User Manual
Lenovo Computer Hardware Z565 User Manual
Line 6 POD Farm GX User Manual
Memorex E IDE User Manual
Philips CD270 User Manual
Philips SmartCard PA0132C User Manual