JVC AV 32D302 User Manual

For models:  
AV-36D502  
AV-36D302  
AV-36D202  
AV-32D502  
AV-32D302  
AV-32D202  
AV-27D502  
COLOR TELEVISION  
USER'S GUIDE  
Illustration of AV-32D502 and RM-C301G  
IMPORTANT NOTE TO THE CUSTOMER  
In the spaces below, enter the model and serial number of your television (located at  
the rear of the television cabinet). Staple your sales receipt or invoice to the inside  
cover of this guide. Keep this user's guide in a convenient place for  
future reference. Keep the carton and original packaging for future use.  
Serial Number  
Model Number  
LCT0903-001B-A  
0201-TN-JII-JIM  
IMPORTANT SAFEGUARDS  
CAUTION:  
Please read and retain for your safety.  
Electrical energy can perform many useful functions. This TV set has been engineered  
and manufactured to assure your personal safety. But improper use can result in poten-  
tial electrical shock or fire hazards. In order not to defeat the safeguards incorporated in  
this TV set, observe the following basic rules for its installation, use and servicing.  
And also follow all warnings and instructions marked on your TV set.  
INSTALLATION  
1 Your TV set is equipped with a polarized AC line plug (one blade of the plug is wider  
than the other).  
(POLARIZED-TYPE)  
This safety feature allows the plug to fit into the power outlet only one way. Should  
you be unable to insert the plug fully into the outlet, try reversing the plug.  
Should it still fail to fit, contact your electrician.  
2 Operate the TV set only from a power source as indicated on the TV set or refer to the  
operating instructions for this information. If you are not sure of the type of power  
supply to your home, consult your TV set dealer or local power company. For battery  
operation, refer to the operating instructions.  
3 Overloaded AC outlets and extension cords are dangerous, and so are frayed power  
cords and broken plugs. They may result in a shock or fire hazard. Call your service  
technician for replacement.  
4 Do not allow anything to rest on or roll over the power cord, and do not place the TV  
set where power cord is subject to traffic or abuse. This may result in a shock or fire  
hazard.  
5 Do not use this TV set near water — for example, near a bathtub, washbowl, kitchen  
sink, or laundry tub, in a wet basement, or near swimming pool, etc.  
6 If an outside antenna is connected to the TV set, be sure the antenna system is  
grounded so as to provide some protection against voltage surges and built-up static  
charges. Section 810 of the National Electrical Code provides information with  
respect to proper grounding of the mast and supporting structure, grounding of the  
lead-in wire to an antenna discharge unit, size of grounding conductors, location of  
antenna discharge unit, connection requirements for the grounding electrode.  
7 An outside antenna system should not be located in the vicinity of overhead power  
lines or other electric light or power circuits, or where it can fall into such power lines  
or circuits. When installing an outside antenna system, extreme care should be taken  
to keep from touching such power lines or circuits as contact with them might be  
fatal.  
EXAMPLE OF ANTENNA GROUNDING  
AS PER NATIONAL ELECTRICAL CODE  
8 TV sets are provided with ventilation openings in the cabinet to allow heat generated  
during operation to be released.  
Therefore:  
— Never block the bottom ventilation slots of a portable TV set by placing it on a  
bed, sofa, rug, etc.  
— Never place a TV set in a “built-in” enclosure unless proper ventilation is provided.  
— Never cover the openings with a cloth or other material.  
— Never place the TV set near or over a radiator or heat register.  
9 To avoid personal injury:  
— Do not place a TV set on a sloping shelf unless properly secured.  
— Use only a cart or stand recommended by the TV set manufacturer.  
— Do not try to roll a cart with small casters across thresholds or deep pile carpets.  
— Wall or shelf mounting should follow the manufacturer’s instructions, and should  
use a mounting kit approved by the manufacturer.  
USE  
10 Caution children about dropping or pushing objects into the TV set through cabinet openings.  
Some internal parts carry hazardous voltages and contact can result in a fire or electrical shock.  
11 Unplug the TV set from the wall outlet before cleaning. Do not use liquid or an  
aerosol cleaner.  
12 Never add accessories to a TV set that has not been designed for this purpose.  
Such additions may result in a hazard.  
13 For added protection of the TV set during a lightning storm or when the TV set is to be left  
unattended for an extended period of time, unplug it from the wall outlet and disconnect  
the antenna. This will prevent damage to product due to lightning storms or power line  
surges.  
14 A TV set and cart combination should be moved with  
care. Quick stops, excessive force, and uneven sur-  
faces may cause the TV set and cart combination to  
overturn.  
SERVICE  
15 Unplug this TV set from the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
A. When the power cord or plug is damaged or frayed.  
B. If liquid has been spilled into the TV set.  
C. If the TV set has been exposed to rain or water.  
D. If the TV set does not operate normally by following the operating instructions.  
Adjust only those controls that are covered in the operating instructions as  
improper adjustment of other controls may result in damage and will often require  
extensive work by a qualified technician to restore the TV set to normal operation.  
E. If the TV set has been dropped or damaged in any way.  
F. When the TV set exhibits a distinct change in performance — this indicates a  
need for service.  
16 Do not attempt to service this TV set yourself as opening or removing covers may  
expose you to dangerous voltage or other hazards. Refer all servicing to qualified  
service personnel.  
17 When replacement parts are required, have the service technician verify in writing  
that the replacement parts he uses have the same safety characteristics as the orig-  
inal parts. Use of manufacturers specified replacement parts can prevent fire,  
shock, or other hazards.  
18 Upon completion of any service or repairs to this TV set, please ask the service techni-  
cian to perform the safety check described in the manufacturers service literature.  
19 When a TV set reaches the end of its useful life, improper disposal could result in a pic-  
ture tube implosion. Ask a qualified service technician to dispose of the TV set.  
20 Note to CATV system installer.  
This reminder is provided to call the CATV system installer’s attention to Article 820-  
40 of the NEC that provides guidelines for proper grounding and, in particular, spec-  
ifies that the cable ground shall be connected to the grounding system of the build-  
ing, as close to the point of cable entry as practical.  
Unpacking Your Television  
Thank you for your purchase of a JVC Color Television. Before you begin setting up your new television,  
please check to make sure you have all of the following items. In addition to this guide, your television  
box should include:  
1 Remote  
Control  
Two AA  
Batteries  
1 Television  
A matching TV stand  
is also available  
(optional).  
Note: Your remote  
control may differ from  
the example illustrated  
here.  
A/V Input Plug  
RF Connectors  
Used to connect  
Used to connect a  
coaxial cable from an  
external antenna or  
Cable TV system.  
audio/video devices like  
VCRs, DVD players,  
stereo amplifiers, game  
consoles, etc.  
S-Video Plug  
Used to make video  
connections with  
VCRs, DVDs,  
Camcorders, etc  
(optional).  
AV Compu Link Cable  
Used to connect JVC  
AV Compu Link  
capable components  
for an automated home  
theater  
We recommend that before you start using your new television, you read your entire User’s Guide  
so you can learn about your new television’s many great features. But if you’re anxious to start  
using your television right away, a quick setup guide follows on the next three pages.  
6
Quick Setup 1  
Getting Started  
These quick setup pages will provide you, in three easy steps, with the basic information you need  
to begin using your new television right away. This information includes basic instructions on  
operating your remote control, making a simple cable/antenna and optional VCR connection and,  
finally, information on programming your television's Auto Tuner.  
If you have questions, or for more detailed information on any of these steps, please consult other  
sections of this manual.  
Step One - The Remote Control  
The remote control is the key to operating your television's many great features. Before you can  
operate your remote control, you first need to install the batteries (included).  
Slide the cover on the back of the remote down towards the bottom of the remote control. Insert two  
batteries (included) carefully noting the “+” and “–” markings, placing the “–” end in the unit first.  
Slide the cover back into place.  
Basic Operation  
Turn the television on and off by pressing the POWER button at the top right corner of the remote.  
Power Button  
Key Feature Buttons  
The four key feature buttons at the center of the remote can be used for basic operation of the  
television. The top and bottom buttons will scan forward and back through the available channels.  
The right and left buttons will turn the volume up or down. These buttons are also marked with four  
arrows and are also used with JVC's onscreen menu system. You will need to use these buttons  
later in the Quick Setup.  
The next step is to connect your television to an antenna or cable.  
Proceed to Step Two  
7
Quick Setup 2  
Step Two - Making Basic Connections  
Next you will need to connect your television to an antenna or cable system. The most basic  
antenna/cable connection is shown below. For more detailed connections, such as ones where a  
cable box is required, see pages 11 to 13.  
Cable/RF connector  
Illustration of AV-32D502  
1) Connect an RF cable out from the wall outlet in to the RFInput on the back of the TV.  
You may also wish to connect a VCR at this point. Abasic VCRconnection is shown below. For  
detailed instructions on connecting a other components or a home theater system, see pages 14 to 16.  
Note: A VCR is not required to operate your television.  
AV Cables/Plugs  
Illustration of AV-32D502  
1) Connect the yellow video cable out from the VCR’s Video Output, in to the TV’s Video Input  
jack, OR connect an S-Video cable from the VCR’s S-Video output, to the TV’s S-Video input.  
2) Connect the white audio cable out from the VCR’s Left Audio Output, in to the TV’s Left Audio  
Input Jack.  
3) Connect the red audio cable out from the VCR’s RightAudio Output, in to the TV’s Right  
Audio Input jack.  
Finally, once you have finished your connections, plug the power cord into the nearest power outlet  
and turn on the television.  
Proceed to Step Three  
8
Quick Setup 3  
Step Three - The Plug In Menu  
When you turn your television on for the first time the Plug In Menu will appear. This menu sets  
some of the basic settings for your television. A complete description of the Plug In Menu can be  
found starting on page 22. We recommend you complete the Plug In Menu items before you start  
using your television. But to begin watching your television right away you only need to run the Auto  
Tuner Setup. This lets your television learn the channels it is able to receive. To run the Auto Tuner  
Setup follow the steps below.  
Press the  
Press the  
buttons to move to AUTO TUNER SETUP  
buttons to begin AUTO TUNER SETUP  
To choose CABLE (if you are connected to a cable system) or AIR (if you use  
an antenna)  
To move to START  
To start Auto Tuner Setup  
The Auto Tuner will now memorize all of the clear, active channels your television can  
receive. This will take one or two minutes.  
The Auto Tuner is finished when the message PROGRAMMINGOVER! appears onscreen.  
Your Quick Setup is now complete. You can now begin watching your television, or you can continue on  
in this guide for more information on connecting audio/video devices, programming your remote control,  
or using the JVC onscreen menu system to customize your television viewing experience.  
The Quick Setup  
is complete  
9
Table of Contents  
Quick Setup Guide . . . . 7  
BUTTON FUNCTIONS  
CONNECTIONS  
Cable and VCR Connections . . . . . . . 11  
Connecting to a DVD Player . . . . . . . 14  
Connecting to an External Amplifier . . . 15  
Menu. . . . . . . . . . . . . . . . . . . 40  
Exit and PIP Off. . . . . . . . . . . . . . 40  
Display . . . . . . . . . . . . . . . . . . 40  
Video Status . . . . . . . . . . . . . . . 41  
Sleep Timer . . . . . . . . . . . . . . . . 41  
Hyper Surround . . . . . . . . . . . . . 41  
Muting . . . . . . . . . . . . . . . . . . 41  
BBE. . . . . . . . . . . . . . . . . . . . 42  
100+ . . . . . . . . . . . . . . . . . . . 42  
Return+. . . . . . . . . . . . . . . . . . 42  
Input. . . . . . . . . . . . . . . . . . . 42  
VCR Buttons . . . . . . . . . . . . . . . 43  
DVD Buttons . . . . . . . . . . . . . . . 43  
TV/CATV Switch . . . . . . . . . . . . . 43  
VCR/DVD Switch . . . . . . . . . . . . . 43  
Light. . . . . . . . . . . . . . . . . . . 43  
PIP (Picture-In-Picture)  
Connecting to a Camcorder . . . . . . . 15  
Connecting to JVC AV Compu Link . . . 16  
GETTING STARTED  
Remote Control  
Remote Control Basics. . . . . 17  
Changing the Batteries. . . . . 17  
Remote Programming . . . . . . . . . . 18  
CATV and Satellite Codes. . . . . . . . . 18  
VCR Codes . . . . . . . . . . . . . . . . 19  
DVD Codes . . . . . . . . . . . . . . . . 20  
Introduction. . . . . . . . . . 44  
MENU FUNCTIONS  
Using the Guide . . . . . . . . . . . . . 21  
Plug In Menu  
On/Move. . . . . . . . . . . . 44  
Freeze. . . . . . . . . . . . . 45  
Swap. . . . . . . . . . . . . . 45  
Channel +/-. . . . . . . . . . 45  
Introduction. . . . . . . . . . 22  
Language. . . . . . . . . . . 22  
Auto Tuner Setup . . . . . . . 22  
Auto Clock Set . . . . . . . . . 23  
Manual Clock Set . . . . . . . 24  
Finish. . . . . . . . . . . . . . 24  
Channel Summary. . . . . . . . . . . . 25  
V-Chip. . . . . . . . . . . . . . . . . . . 26  
Set Lock Code. . . . . . . . . 33  
Picture Settings  
Source. . . . . . . . . . . . . 45  
APPENDICES  
Troubleshooting . . . . . . . . . . . . . 46  
Warranty . . . . . . . . . . . . . . . . . 47  
Authorized Service Centers . . . . . . . 49  
Search Codes. . . . . . . . . . . . . . . 50  
Specifications. . . . . . . . . . . . . . . 51  
Tint . . . . . . . . . . . . . . . 34  
Color . . . . . . . . . . . . . . 34  
Picture  
. . . . . . . . . 34  
Bright . . . . . . . . . . . . . 34  
Detail . . . . . . . . . . . . . 34  
Noise Muting . . . . . . . . . 35  
Set Video Status . . . . . . . . 35  
Sound Settings  
Bass . . . . . . . . . . . . . . 36  
Treble . . . . . . . . . . . . . 36  
Balance . . . . . . . . . . . . 36  
MTS (Multi-channel Sound) 36  
General Items  
On/Off Timer . . . . . . . . . . 37  
TV Speaker . . . . . . . . . . 38  
V2 Component-In . . . . . . . 39  
Closed Caption . . . . . . . . 39  
Connections  
Cable and VCR Connections  
Diagram #1  
Illustration of AV-32D502  
1) Connect the antenna or cable TV wire from the wall outlet, in to the RFInput of the two-way splitter.  
2) Connect an RF cable from the one of the RFOutputs on the splitter, in to the RF Input on the  
back of the VCR.  
3) Connect an RF cable from the other the RF Output on the splitter, in to the RF Input on the  
back of the TV.  
4) Connect the yellow video cable out from the VCR’s Video Output, in to the TV’s Video Input  
jack, OR connect an S-Video cable from the VCR’s S-Video output, to the TV’s S-Video input.  
5) Connect the white audio cable out from the VCR’s Left Audio Output, in to the TV’s Left Audio  
Input Jack.  
6) Connect the red audio cable out from the VCR’s Right Audio Output, in to the TV’s Right  
Audio Input jack.  
If your VCR is a mono sound unit, it will have only one Audio Out jack. Connect it to the TV’s  
Left Audio Input.  
Please consult your VCR’s owners manual for more information on its operation.  
11  
Connections  
Cable and VCR Connections - Continued  
Diagram #2  
Illustration of AV-32D502  
1) Connect the antenna or cable TV wire from the wall outlet, in to the RFInput of the cable box.  
2) Connect an RF cable from the RF Output of the cable box, in to the RF Input on the back of  
the VCR.  
3) Connect an RF cable from the RF Output of the VCR, in to the RF Input on the back of the TV.  
4) Connect the yellow video cable out from the VCR’s Video Output, in to the TV’s Video Input  
jack, OR connect an S-Video cable from the VCR’s S-Video output, to the TV’s S-Video input.  
5) Connect the white audio cable out from the VCR’s Left Audio Output, in to the TV’s Left Audio  
Input Jack.  
6) Connect the red audio cable out from the VCR’s Right Audio Output, in to the TV’s Right  
Audio Input jack.  
Please see page 44 for information on using the PIP feature with a Cable Box.  
If your VCR is a mono sound unit, it will have only one Audio Out jack. Connect it to the TV’s  
Left Audio Input.  
Please consult your VCR’s owner’s manual for more information on its operation.  
12  
Connections  
Cable and VCR Connections - Continued  
Diagram #3  
Illustration of AV-32D502  
1) Connect the antenna or cable TV wire from the wall outlet, in to the RFInput of the two-way splitter.  
2) Connect an RFcable from the one of the RFOutputs on the splitter, in to the cable box RF Input.  
3) Connect an RFcable from the Cable Box Output, in to the VCR RFInput.  
4) Connect an RFcable from the other the RFOutput on the splitter, in to the RFInput on the back of  
the TV.  
5) Connect the yellow video cable out from the VCR’s Video Output, in to the TV’s Video Input jack, OR  
connect an S-Video cable from the VCR’s S-Video output, to the TV’s S-Video input.  
6) Connect the white audio cable out from the VCR’s Left Audio Output, in to the TV’s Left Audio Input  
jack.  
7) Connect the red audio cable out from the VCR’s RightAudio Output, in to the TV’s Right Audio Input  
jack.  
Please see page 44 for information on using the PIP feature with a Cable Box.  
If your VCR is a mono sound unit, it will have only one Audio Out jack. Connect it to the TV’s  
Left Audio Input.  
Please consult your VCR’s owners manual for more information on its operation.  
13  
Connections  
Connecting to a DVD player  
Illustration of AV-32D502  
1) Connect Green cable out from DVDplayer “Y”Component Output, in to TV“Y” Component Input.  
2) Connect Blue cable out from DVDplayer “PB”Component Output, in to TV“PB”Component Input.  
3) Connect Red cable out from DVDPlayer “PR”Component Output, in to TV“PR” Component Input.  
4) Connect White Audio cable out from DVDLeft Audio Output, in to TV Left Audio Input 2.  
5) Connect Red Audio cable out from DVDRight Audio Output, in to TV Right Audio Input 2.  
Green, blue and red are the most common colors for DVD cables. Some models may vary colors,  
please consult the user’s manual for your DVDPlayer for more information.  
Be careful not to confuse the red DVDcable with the red audio cable. It is best to complete one set  
of connections (DVDor Audio Output) before starting the other to avoid accidentally switching the  
cables.  
See page 20 for instructions on programming your remote control to operate the basic functions of  
your DVD player.  
If you use Input 2 (Component-In) for the DVD connection, you must set the  
V2 COMPONENT-IN on the initial Setup Menu to “YES” for proper display of the DVD signal.  
NOTE:Progressive DVDPlayers (players with an output scan of 31.5 KHz) will not work properly  
with this television.  
14  
Connections  
Connecting to an External Amplifier  
Illustration of AV-32D502  
1) Connect the white audio cable from the TV’s Left Audio Output jack to the Amplifier’s Left Audio  
Input jack.  
2) Connect the red audio cable from the TV’s Right Audio Output jack to the Amplifiers Right Audio  
Input jack.  
See also “TVSpeaker” on page 38 for more information on using external speakers.  
Connecting to a Camcorder  
Illustration of AV-32D502  
1) Connect the yellow video cable out from the Camcorder’s Video Output, in to the TV’s Video  
Input jack.  
2) Connect the white audio cable out from the Camcorder’s Left Audio Output, in to the TV’s Left  
Audio Input Jack.  
3) Connect the red audio cable out from the Camcorder’s Right Audio Output, in to the TVs  
Right Audio Input Jack.  
If your Camcorder is a mono sound model it will have only one audio jack. Connect it to the  
TV’s Left Audio Jack.  
15  
Connections  
Connecting to JVC AV Compu Link  
Illustration of AV-32D502  
To Connect: Plug one end of the AVCompu Link cable into the AVCompu Link input on your VCR,  
DVD, or other Compu Link device. Plug the other end of the AV Compu Link cable into the AV Compu  
Link input at the rear of the television.  
NOTES:  
* In order for the VCRplayback to begin automatically, the recording tabs must be removed from the  
VHStape. If the tab is in place, automatic switching will occur when you push the VCRs PLAY button.  
• The AV Compu Link cable has a male 3.5 mm (mono) plug on each end.  
• If your JVC-brand VCRhas “A Code/B Code Remote Control Switching” (see your VCRs instruction  
book), using VCRA Code will switch the TV to input 1.  
To connect a JVC HiFi receiver or amplifier for a completely automated home theater, see the HiFis  
connection instructions for detailed connection information.  
AV COMPULINK EX is compatible with the following receivers:RX-664V, RX-665V, RX-668VBK,  
RX-774V, RX-778VBK, RX-884V, RX-888VBK, RX-1024V, RX-1028VBK, and later receiver models.  
16  
Remote Control  
Remote Control Basics  
Before you can operate the remote control, you must first install  
the batteries (included). See “Changing the Batteries” at the  
bottom of this page for instructions. (For an illustration, please see  
page 7.)  
Press the POWER button to turn the television on or off.  
Make sure the TV/CATV switch is set to TV. Move the switch to  
CATV only if you need to operate a cable box.  
Slide the VCR/DVD selector switch to VCR to control a VCR,  
slide to DVDto control a DVD player. Please see pages 18 to  
20 for instructions on programming your remote control to  
operate a Cable box, VCR or DVDplayer.  
Press the CH+ and CH- buttons to scan through the channels.  
Tap the CH+ or CH- button to move through the channels one  
channel at a time.  
To move rapidly through the channels using JVC’s Hyperscan  
feature, press and hold CH+ or CH-. The channels will zip by at  
a rate of five channels per second.  
Press VOL+ or VOL - to raise or lower the volume. An indicator  
bar will appear onscreen to show you the television volume  
level.  
The CH+/- and VOL+/- buttons are also used to navigate JVC’s  
onscreen menu system.  
You can directly access specific channels using the 10-key pad.  
For more information on remote control button features, see  
pages 40 to 45. For information on using the onscreen menus,  
see page 21.  
Notes: Remote control model RM-C301G is shown at the left.  
A different model remote control may have come with your  
television.  
Changing the Batteries  
Push down on the remote’s back cover and slide towards the bottom to remove it.  
Insert two AAbatteries (supplied), carefully noting the "+" and "-" markings on the batteries and on  
the remote control. To avoid a potential short circuit, insert the "-" end first. Be sure to use only size  
AA batteries.  
When batteries are installed, slide the cover back into place (until it clicks into position).  
• If the remote control acts erratically, replace the batteries. Typical battery life is six months to one  
year. We recommend using alkaline batteries for longer battery life.  
When you change the batteries, try to complete the task within three minutes. If you take longer than three  
minutes, the remote control codes for yourVCR, DVD, and/or Cable Box may have to be reset (see page 18-20).  
17  
Remote Programming  
Setting the CATV, VCR and DVD Codes  
Cable Box or Satellite codes  
The remote control is programmed with CATV and/or Satellite codes for power on, power off,  
channel up, channel down, and 10 key operation.  
1) Find the CATV/Satellite brand from the list of codes shown below.  
2) Slide the 2-way selector switch to “CATV”.  
3) Press and hold down the DISPLAY button.  
4) With the DISPLAY button held down, enter the first code number listed using the 10 key pad.  
5) Release the DISPLAY button.  
6) Confirm the operation of the Cable Box/Satellite receiver.  
• If your CATV or Satellite box does not respond to the first code, try the others listed. If it does not  
respond to any code, try the Search Codes Function, on page 50.  
18  
Remote Programming  
VCR codes  
The remote control is programmed with VCR codes for power on, power off, play, stop, fast-forward,  
rewind, pause, record, channel up, and channel down operation.  
1) Find the VCR brand from the list of codes shown below.  
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.  
3) Press and hold down the DISPLAY button.  
4) With the DISPLAY button held down, enter the first code number listed with the 10 key pad.  
5) Release the DISPLAY button.  
6) Confirm the operation of the VCR.  
• If your VCR does not respond to the first code, try the others listed. If it does not respond to any  
code, try the Search Codes Function, on page 50.  
• Some manufacturer’s VCR’s may not respond to the TV/VCRbutton, even if other buttons work properly.  
To record, hold down the REC button on the remote and press PLAY.  
19  
Remote Programming  
DVD codes  
The remote control is programmed with DVD codes for power on, power off, play, stop,  
fast-forward, rewind, previous chapter, next chapter, tray open/close, and still/pause operation.  
1) Find the DVD player brand from the list of codes shown below.  
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.  
3) Press and hold down the DISPLAY button.  
4) With the DISPLAY button held down, enter the first code number listed with the 10 key pad.  
5) Release the DISPLAY button.  
6) Confirm the operation of the DVD player.  
• If your DVD player does not respond to the first code, try the others listed. If it does not respond  
to any code, try the Search Codes Function, on page 50.  
• After you program your remote, some DVD buttons may not work properly. If some buttons do not  
work properly, use the remote control which came with your DVDplayer.  
20  
Onscreen Menus  
Using the Guide  
Certain symbols are used throughout this guide to help you learn about the features of your new  
television. The ones you will see most frequently are:  
Up and Down arrows mean press the CH+ or CH- buttons. Pressing the CH+ or CH- buttons  
let you:  
• Move vertically in a main menu screen  
• Move through a submenu screen  
• Move to the next letter, number, or other choice in a submenu  
• Back up to correct an error  
• Scan through TVchannels (when not in a menu screen)  
Left and right arrows mean press the VOLUME+ or VOLUME- buttons to move left or right to:  
• Select a highlighted menu item  
• Select an item in a submenu  
• Select numbers in certain menu options  
• Turn the volume up or down (when not in a menu screen)  
The “Press Button”icon means you should press the button named on your remote control.  
(Button names appear in SMALL CAPITAL LETTERS.)  
The “Helping Hand” icon points to the highlighted or selected item in a menu.  
The Onscreen Menus  
To bring up the onscreen menu, press the MENU button on the remote control. The item that  
appears in yellow is the one currently selected. If you press the MENU button again, the onscreen  
display will skip to the next menu screen. If you use the Menu button on the TVs front panel instead of  
the remote, an additional menu screen showing channel number and input will appear. The “Plug In  
Menu” will appear the first time the TV is plugged in.  
Notes: Menus shown in this book are illustrations, not exact replications of the television’s  
onscreen displays.  
21  
Plug In Menu  
Introduction  
The Plug In Menu comes up automatically when you first turn on the TV after plugging it in. The  
Plug In Menu helps you to get your TV ready to use by letting you set your preferences for:  
• The Language in which you want the onscreen menus to appear,  
• The Auto Tuner Setup of which channels you wish to receive,  
• Setting the TV’s clock to the correct time so your timer functions will work properly.  
Descriptions of each of the Plug In Menu features appear on this page and the next. We recommend  
you complete the Plug In Menu setup first so your TV is set up just the way you want, right away.  
Language  
You can choose to view your onscreen menus in three languages: English, French, or Spanish.  
Press the MENU button  
To LANGUAGE  
To choose a language  
You will not need to press the MENU button to enter this screen from the Plug In Menu.  
Auto Tuner Setup  
In Auto Tuner Setup, the TV automatically scans through all available channels, memorizing the active  
ones and skipping over blank ones or channels with weak signals. This means when you scan (using  
the CHANNEL+/-buttons)you will receive only clear, active channels.  
Press the MENU button  
ToAUTO TUNER SETUP  
To operate  
To choose CABLEor AIR  
To move to START  
To start Auto Tuner Setup  
48  
Programming will take approximately 1 to 2  
minutes.  
• Noise Muting will not work during Auto Tuner Setup.  
You will not need to press the MENU button to enter this screen from the Plug In Menu.  
22  
Plug In Menu  
Auto Clock Set  
Before you use any of your TV’s timer functions, you must first set the clock. You may precisely set  
your clock using the XDS time signal broadcast by most Public Broadcasting stations. To set the  
clock using the XDS signal:  
Enter the channel number of your local PBS station  
Press MENU  
To SET CLOCK  
To operate  
ToAUTO  
To TIME ZONE  
To select your time zone  
To move to Daylight Savings Time (D.S.T.)  
To turn D.S.T. ON or OFF  
To FINISH  
To save settings and exit  
• If you do not have a PBS station in your local area, you will have to set the clock manually. See  
‘Manual Clock Set’on the next page for instructions.  
• The Daylight Savings Time feature automatically adjusts your TV’s clock for Daylight Savings. The  
clock will move forward one hour at 2:00 am on the first Sunday in April. The clock will move back  
one hour at 2:00 am on the last Sunday in October.  
You will not need to press the MENU button to enter this screen from the Plug In Menu.  
23  
Plug In Menu  
Manual Clock Set  
To set your clock manually (without using the XDS signal), choose MANUALfrom the Set Clock  
menu and follow the steps below.  
To SET CLOCK  
To operate  
To MANUAL  
To move to the hour  
To set the hour  
To move to minutes  
To set the minutes  
To move to START CLOCK  
To start clock and exit  
•You will not need to press the MENU button to enter this screen from the Plug In Menu.  
Finish  
Once you have the items in the Plug In Menu set to your personal preferences, move to the  
Finish option to save your settings.  
To FINISH  
To save settings and exit  
You can change the preferences you set in the Plug In Menu at any time using the regular JVC  
onscreen menu system.  
NOTES:  
You will have to reset the clock after a power interruption. You must set the clock before operating  
any timer functions.  
24  
Channel Summary  
Channel Summary  
Channel Summary allows you to customize the line-up of channels received by your TV. You can  
add or delete channels from the line-up or prevent any unauthorized viewers from watching any or  
all 181 channels.  
Press the MENU button  
To CHANNELSUMMARY  
To operate  
CHNO. SCAN  
01  
CHNO. SCAN  
06  
07  
08  
09  
10  
ü
02  
03  
04  
05  
ü
ü
ü
ü
ü
ü
The Channel Summary screen (above) will now be displayed with the channels set to scan marked  
with an "ü". You can delete channels from the scan by removing the "ü". If any channels were  
missed during Auto Tuner Setup and you wish to add them, you may by placing an "ü" next to the  
channel number.  
To the SCAN column  
To include or delete from scan  
EXIT when finished  
You can block access to a channel by activating the Channel Lock.  
To CHANNEL SUMMARY  
To operate  
To the Lock Column  
ZERO to lock or unlock that channel  
EXIT when finished  
Channel Guard Message  
When a viewer attempts to watch a guarded channel, the following message appears:  
To watch a channel that you have locked,  
enter the Lock Code using the 10 key pad.  
If the wrong code is entered, the message  
“INVALID LOCK CODE!” will flash on the  
screen:  
The channel cannot be accessed until the  
correct code is entered.  
• Once a channel has been unlocked, it will remain unlocked until the television is turned off.  
• See also “Set Lock Code”, page 33.  
25  
V-Chip  
Your TV is equipped with V-Chip technology which enables TV Parental Guidelines (for United  
States and Canada) and Movie (MPAA) Guideline controls. V-Chip technology allows you to pro-  
gram your TVto receive, or not to receive, programs based on content according to the guidelines.  
Programs which exceed the ratings limits you set will be blocked. When a viewer attempts to watch  
a blocked channel, this message appears:  
The channel will remain blocked until the correct lock code is entered (see page 33 for information  
on setting your lock code).  
You can customize the V-Chip settings of your television to match your personal tastes. The V-Chip  
menu below is the starting point for your V-Chip settings  
You can use US V-Chip settings (for programming broadcast from the United States), Canadian  
V-Chip settings (for programming broadcast from Canada), and movie ratings. You may use any or all of  
the settings (US V-Chip, Canada V-Chip, Movie ratings). Descriptions for setting each of the three  
V-Chip formats appear in the next seven pages along with descriptions of the rating categories.  
To access the rating categories:  
Press the MENU button  
To V-CHIP  
To operate (Lock icon  
will appear)  
Press ZERO to access the V-Chip menu  
To turn V-Chip ON or OFF (V-Chip must be turned ON for rating settings to operate)  
To move to SET US TVRATINGS, SETMOVIE RATINGS, or SET CANADIANRATINGS  
(see following pages for descriptions of each item)  
26  
V-Chip  
US V-Chip Ratings  
U.S. PARENTAL RATING SYSTEMS  
Programs with the following ratings are appropriate for children.  
TVY is Appropriate for All Children.  
Programs are created for very young viewers and should be suitable for all ages, including  
children ages 2 - 6.  
TV Y7 is for Older Children.  
Most parents would find such programs suitable for children 7 and above. These programs may  
contain some mild fantasy violence or comedic violence, which children should be able to discern  
from reality.  
Programs with the following ratings are designed for the entire audience.  
TV G stands for General Audience.  
Most parents would find these programs suitable for all age groups. They contain little or no  
violence, no strong language, and little or no sexual dialog or situations.  
TV PG Parental Guidance Suggested.  
May contain some, but not much, strong language, limited violence, and some suggestive sexual  
dialog or situations. It is recommended that parents watch these programs first, or with their  
children.  
TV 14 Parents Strongly Cautioned.  
Programs contain some material that may be unsuitable for children under the age of 14  
including possible intense violence, sexual situations, strong coarse language, or intensely  
suggestive dialog. Parents are cautioned against unattended viewing by children under 14.  
TV MA Mature Audiences Only.  
These programs are specifically for adults and may be unsuitable for anyone under 17 years of  
age. TV MAprograms may have extensive V, S, L, or D.  
Viewing Guidelines  
In addition to the ratings categories explained above, information on specific kinds of content are also  
supplied with the V-Chip rating. These types of content may also be blocked. The content types are:  
V/FV is for VIOLENCE/FANTASYVIOLENCE  
L stands for strong LANGUAGE  
S stands for SEXUAL CONTENT  
D stands for suggestive DIALOG  
27  
V-Chip  
Setting US V-Chip Ratings  
Press the MENU button  
To V-CHIP  
To operate (Lock icon  
will appear)  
Press ZERO to access the V-Chip menu  
To turn V-Chip ON or OFF  
To move to SET US TVRATINGS  
To operate  
Directions to set US V-Chip Ratings:  
Line up the cursor in the column (TVPG, TV G, etc.) with the content row (V/FV, S, etc.) and press the  
or to move the cursor to the correct location. Press or to turn the locking feature on or off. An  
item is locked if the  
icon appears instead of a “—”.  
For example. To block viewing of all TV 14 shows, move the cursor to the top row of that column  
and add a lock icon. Once you've put a lock on the top row, everything in that column is  
automatically locked.  
To the TV 14 Column  
To turn on the lock  
To FINISH  
To save settings and exit  
• If you want to change the setup, move the cursor to the top column and change the lock icon to  
“—” by pressing  
or again. You may then select individual categories to block.  
28  
V-Chip  
Setting ratings with the V-Chip button  
To access Rating information about a certain program, press the V-CHIP button while viewing that  
program. A display like this will appear:  
If you decide you want to block this category of viewing, press "0" while the above screen is  
visible, and all programs from that category will be blocked.  
Example 1:  
If you want to set your V-Chip settings to block all programming above TV-PG:  
Press ZERO when TV-PG is displayed  
All Programming above TV-PG will be blocked.  
Example 2:  
If you want to set your V-Chip settings to block all programming above a current setting such as  
TVPG-V (with violence):  
Press ZERO when TV-PG - V is displayed  
All Programming above TV-PG- V (with Violence) will be blocked.  
• For Children's programming you can block TV-Y and Y7 programs by Pressing “0” when Y is  
displayed during a program. Programming for audiences other than children’s audiences will not be  
affected.  
29  
V-Chip  
Movie Ratings  
NR - Not Rated.  
This is a film which has no rating. In many cases these films were imported from countries which do  
not use the MPAA ratings system. Other NRfilms may be from amateur producers who didn’t intend to  
have their film widely released.  
NR(Not Rated) Programming may contain all types of programming including children's  
programming, foreign programs, or adult material.  
G – General Audience.  
In the opinion of the review board, these films contain nothing in the way of sexual content,  
violence, or language that would be unsuitable for audiences of any age.  
PG – Parental Guidance.  
Parental Guidance means the movie may contain some contents such as mild violence, some brief  
nudity, and strong language. The contents are not deemed intense.  
PG-13 – Parents Strongly Cautioned.  
Parents with children under 13 are cautioned that the content of movies with this rating may  
include more explicit sexual, language, and violence content than movies rated PG.  
R - Restricted.  
These films contain material that is explicit in nature and is not recommended for unsupervised  
children under the age of 17.  
NC-17 - No One Under 17.  
These movies contain content which most parents would feel is too adult for their children to view.  
Content can consist of strong language, nudity, violence, and suggestive or explicit subject matter.  
X - No One under 18.  
Inappropriate material for anyone under 18.  
Directions to set Movie (MPAA) Ratings:  
Press the MENU button  
To V-CHIP  
To operate (Lock icon  
appears)  
Press ZERO to access V-Chip setup options  
To SET MOVIE RATINGS  
To enter movies menu  
For example, to block viewing of X and NC-17 rated from shows:  
To the X Column  
To turn on the lock  
To the NC-17 Column  
To turn on the lock  
To FINISH  
To save settings and exit  
30  
V-Chip  
Canadian V-Chip Ratings  
E - Exempt.  
Exempt programming includes: news, sports, documentaries and other information programming, talk  
shows, music videos, and variety programming.  
C – Programming Intended for Children.  
Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive  
behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or  
unrealistic in nature.  
C8+ – Programming Intended for Children 8 and Over.  
Violence Guidelines: Any realistic depictions of violence will be infrequent, discreet, of low intensity and  
will show the consequences of the acts. There will be no offensive language, nudity or sexual content.  
G – General Audience.  
Programming will contain little violence and will be sensitive to themes which could affect  
younger children.  
PG - Parental Guidance.  
Programming intended for a general audience, but which may not be suitable for younger  
children. Parents may consider some content not appropriate for children aged 8-13.  
14+ - 14 Years and Older.  
Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and early  
teens. Programming may contain mature themes and scenes of intense violence.  
18+ - Adult.  
Material intended for mature audiences only.  
Directions to set Canadian V-Chip Ratings:  
Press the MENU button  
To V-CHIP  
To operate (Lock icon  
appears)  
Press ZERO to access V-Chip setup options  
To SET CANADIAN RATINGS ENG (for English)  
To enter ratings menu  
For example, to block viewing of programming rated 14+ and 18+ :  
To the 18+ Column  
To turn on the lock  
To the 14+ Column  
To turn on the lock  
To FINISH  
To save settings and exit  
• For instructions on “Set Canadian Ratings FRE (in French)”, please see page 31 in the French side of  
this user’s guide.  
31  
V-Chip  
Unrated Programs  
Notes About Unrated Programs:  
Unrated programming refers to any programming which does not contain a rating signal.  
Programming on television stations which do not broadcast rating signals will be placed in the  
“Unrated Programming" category.  
Examples of Unrated programs:  
Emergency Bulletins  
Locally Originated Programming  
News  
Political Programs  
Public Service Announcements  
Religious Programs  
Sports  
Weather  
Some Commercials  
• TV programs or movies that do not have rating signals will be blocked if the Unrated Category is  
set to BLOCK.  
Directions to Block Unrated Programs:  
You can block programs that are not rated.  
Press the MENU button  
To V-CHIP  
To operate (The lock icon  
appears)  
Press ZERO to access V-Chip setup options  
To UNRATED  
To VIEW or BLOCK  
Press EXIT when done  
32  
V-Chip  
Set Lock Code  
Channel Guard and V-Chip settings are protected by a four-digit Lock Code. Your TV comes pre-set  
with a Lock Code of "0000". You may change the code to any four-digit number you wish. To  
change the Lock Code, follow the steps below.  
Press the MENU button  
To SET LOCK CODE  
To operate  
The lock icon  
appears  
Press ZERO to access the Lock Code  
0
The first digit will be highlighted  
To select the number  
To move to the next digit  
Continue to follow these directions for all four numbers  
To FINISH  
To save settings and exit  
Your Lock Code is now set.  
NOTES:  
• After a power interruption you must reset the Lock Code.  
• Write your Lock Code number down and keep it hidden from potential viewers.  
• If you forget the Lock Code, a new code may be set using the steps listed above.  
33  
Picture Settings  
Tint  
Tint allows you to adjust the levels of red and green in your TV picture.  
Press the MENU button  
To TINT  
To increase the levels of green  
To increase the levels of red  
To move to the next setting  
Color  
The color function lets you make all the colors in the TV picture appear either more vivid or subtle.  
Press the MENU button  
To COLOR  
To make the colors more vivid  
To make the colors more subdued  
To move to the next setting  
Picture  
Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker or  
brighter picture overall.  
Press the MENU button  
To PICTURE  
To increase the level of contrast  
To decrease the level of contrast  
To move to the next setting  
Bright  
You can adjust the overall brightness of the TV picture with the Bright control.  
Press the MENU button  
To BRIGHT  
To lighten the picture  
To darken the picture  
To move to the next setting  
Detail  
The Detail feature adjusts the level of fine detail displayed in the picture.  
Press the MENU button  
To DETAIL  
To make the picture sharper (more detail)  
To make the picture smoother (less detail)  
To move to the next setting  
34  
Picture Settings  
Noise Muting  
This feature inserts a blank blue screen over channels which are not broadcasting or are too weak  
to be received clearly.  
Press the MENU button  
To NOISE MUTING  
To turn Noise Muting ON or OFF  
• Noise Muting will not work during Auto Tuner Setup or when you operate Channel Summary.  
Set Video Status  
With Set Video Status, you can save your own set of picture quality adjustments as “Choice” and  
have access to them at the touch of a button.  
Press the MENU button  
To SET VIDEO STATUS  
To operate  
To set the TINT levels  
To move to the next option  
Repeat these steps until all levels are set.  
To SAVEAS CHOICE  
To save settings and exit  
• You must use SAVEAS CHOICE to exit the Set Video Status menu, otherwise your preferences  
will not be saved.  
• You can access your “Choice” settings at any time by pressing the VIDEO STATUS button on the  
remote control.  
NOTES:  
The setting screen will disappear if you do not make any adjustments or move to the next setting in  
approximately three seconds. Any changes you have made to picture settings up to that point will  
be stored. You can exit the Picture Settings menu at any time by pressing the EXIT button on the  
remote control.  
35  
Sound Settings  
Bass  
You can increase or decrease the level of low-frequency sound in the TVs audio with the Bass adjustment.  
Press the MENU button  
To BASS  
To increase the bass  
To decrease the bass  
To move to the next setting  
Treble  
Use Treble to adjust the level of high-frequency sound in your TV’s audio.  
Press the MENU button  
ToTREBLE  
To increase the treble  
To decrease the treble  
To move to the next setting  
Balance  
Adjust the level of sound between the TV’s two speakers with the Balance setting.  
Press the MENU button  
To BALANCE  
To shift the balance towards the right speaker  
To shift the balance towards the left speaker  
To move to the next setting  
MTS (Multi-Channel Television Sound)  
MTS technology allows several audio signals to be broadcast at once, giving you a choice in what  
you wish to hear with a TV program. In addition to mono or stereo sound, an MTSbroadcast may  
also include a Second Audio Program (SAP).  
Press the MENU button  
To MTS  
Select the mode  
(The ON AIR arrow tells you if a broadcast is in Stereo and/or contains an SAP).  
• Keep the TV in STEREO mode to get the best sound quality. The sound will work in STEREO  
mode even if a certain broadcast is in MONO sound only.  
• Choose the MONO setting to reduce excessive noise on a certain channel or broadcast.  
• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.  
NOTE:  
You can leave the Sound Settings menu at any time by pressing the EXIT button on the remote control.  
36  
General Items  
On/Off Timer  
The On/Off timer lets you program your television to turn itself on or off. You can use it as an alarm  
to wake up, to help you remember important programs, or as a decoy when you're not home.  
Press the MENU button  
To ON/OFF TIMER  
To operate (begins with ON TIME)  
To set the hour (AM/PM) you want the TV to turn on  
To move to minutes  
To set the minutes  
To accept ON TIME and move to OFF TIME (the time the TV will turn off). Set the  
OFF TIME the same way as ONTIME  
To accept OFFTIME and move to CHANNEL  
To select channel  
To move to MODE  
Choose ONCE or EVERYDAY  
To ON/OFFTIMER  
Choose YES to accept the timer setting, choose NOif you don't wish to accept  
To FINISH  
To save settings  
On/Off Timer Note for PIP (D502 models) only.  
If the television is on when a timed event is about to start a Timer Preview window will appear. The  
Timer Preview window will appear in the lower right corner of the screen seven seconds before the  
timer is programmed to begin. When the timer activates, the Preview picture will become the main  
picture.  
NOTES:  
• The On/Off time cannot be set to locked or guarded channels.  
• In order for the On/Off timer to work, the clock must be set.  
• After a power interruption, the Timer settings must be reset.  
37  
General Items  
TV Speaker  
If your TV is connected to a stereo system, you can turn off the TV speakers and listen to the audio  
through your stereo.  
Press the MENU button  
To TV SPEAKER  
To turn the TV's speakers ONor OFF  
EXIT when finished  
• Before you turn the TV Speaker setting from OFF to ON, make sure that theTV volume level is low!  
If theTV volume is set too high, the sound level will be extremely loud.  
• After a power interruption, the TV Speaker settings will return to “ON”.  
NOTE:  
External Speakers: When using external speakers or amplifiers, shut off the TV Speakers  
(see ‘TV Speaker’) above.  
38  
General Items  
V2 Component-In  
Get the best quality video from your DVD player by using this setting and the DVD inputs at the rear  
of the television. Set either to YES for component input (for DVD) or to NO for composite video  
input (for a regular VCR).  
Press the MENU button  
To V2 COMPONENT-IN  
To turn the input ON (YES) or OFF (NO)  
EXIT when finished  
• This option should be used with DVD players only. For information on connecting VCR’s see  
page 11. For more information on connecting a DVD player, see page 14.  
Closed Caption  
Many broadcasts now include an onscreen display of dialog called Closed Captions. Some broad-  
casts may also include displays of additional information in text form. Your television can access and  
display this information using the Closed Caption feature. To activate the Closed Caption feature,  
follow the steps below.  
Press the MENU button  
To CLOSED CAPTION  
To operate  
To select CAPTION (for Closed Captions), TEXT (for text display), or OFF (for no display)  
To move to CAPTION or TEXT  
To select a caption (CC1 to CC4) or text channel (T1 to T4)  
To accept that selection and move to FINISH  
To save settings and exit  
NOTES:  
• Closed Caption subtitles are usually found on closed caption channel CC1. Some programs may include addi-  
tional text information which is usually found on text channel T1. The other channels are available for future use.  
• Closed captioning may not work correctly if the signal being received is weak or if you are playing a video tape.  
• Most broadcasts containing Closed Captioning will display a notice at the start of the program.  
39  
Button Functions  
Menu  
The MENU button allows you to access JVC’s onscreen menu system. Press MENU to activate the  
onscreen menu system.  
• See individual topics (like “Sound Settings) for specific information on using menus.  
Exit and PIP Off  
Press the EXIT button to leave a menu screen. On the RM-C301G this button is also labeled “PIP  
OFF”. Press EXIT/PIP OFF to turn off the Picture-in-Picture function (please see page 44 for more  
information on the PIP feature).  
PIPis available on series D502 models only.  
Display  
The Display screen shows the current status of timers and inputs.  
Press the DISPLAY button  
The screen above shows the following information:  
• The current channel or AV input (Channel 07)  
• The current time (12:20 pm)  
• Sleep Timer status/minutes remaining (The Sleep Timer is off)  
• On/Off Timer status (Set to turn on everyday at 7:00 PM, off at 10:00 PM)  
• Each Press of the DISPLAY button changes the display mode:  
Display - Full screen shown above  
Time - Shows the current time only  
Channel - Shows the current channel  
Off - Turns Display off  
You may also turn off the Display at any step by pressing EXIT.  
NOTE:  
• Please note that if the Clock, Sleep Timer or On/Off Timer are not set, the Display screen will  
show: "Clock Not Set", "Sleep Timer Off", and "On/Off Timer Off" respectively.  
40  
Button Functions  
Video Status  
The VIDEO STATUS button gives you a choice of three TV picture display settings, including a  
display of your own preferences.  
Standard - Resets the picture display to the factory settings.  
Choice - Displays the setting levels you specified on the "Set Video Status" Menu (see page 35).  
Theater - Gives a rich, film-like look to video.  
Press the VIDEO STATUS button  
Sleep Timer  
The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals of  
15 minutes, for a total time of up to 180 minutes.  
Press the SLEEP TIMER button  
SleepTimer Message  
20 seconds before the automatic shutoff, this message will appear:  
You then have 20 seconds to press the Sleep Timer button to delay the shutoff for another 15 minutes.  
Hyper Surround  
Creates a deep, three-dimensional sound effect by channeling the audio through the TV's front-firing  
speakers. Press the HYPER SURROUND button to turn the effect on or off.  
Muting  
The MUTING button instantly turns the volume down completely when you press it.Press MUTING and the  
volume level will instantly go to zero. To restore the volume to its previous level, press MUTING again.  
41  
Button Functions  
BBE  
BBE high definition audio adds natural, clear and extraordinary sound quality to any program. Turn  
BBE On or Off using the BBE button.  
100+ Button  
Use the 100+ button to directly access channels above Channel 99. For example to move to channel 124,  
press100+, 2 (two), 4 (four).  
Return+  
The RETURN+ button has two functions:  
Return - Returns to the channel viewed just before the channel currently onscreen.  
Return+ - Lets you program a specific channel to return to while scanning through the channels  
using the CH+ and CH- buttons.  
RETURN+ and hold for three seconds  
The channel currently active has been programmed as your Return+ channel. Now scan through  
the channels using the CHANNEL+/- buttons  
RETURN+  
You will return to your programmed channel.  
• To cancel your Return+ channel, press and hold the RETURN+button for three seconds. The message  
“RETURN CHANNELCANCELLED!” will appear.  
• Return+ works only with the CHANNEL+/- buttons. Pressing any number key will cancel Return+.  
• Return+ does not affect the PIP channel (D502 models only).  
Input  
Selects the signal input source for the television: TV (for Antenna or Cable) or Video-1, 2 or 3 for  
video devices like VCR’s, DVD players, or camcorders.  
INPUT  
NOTE:  
• BBE is a registered trademark of BBESound, Inc. For U.S., licensed from BBE Sound, Inc. under  
USP 4638258, 4482866 and 5510572. For Canada, licensed from BBESound, Inc. BBE is a regis-  
tered trademark of BBE Sound, Inc.  
42  
Button Functions  
VCR Buttons  
You can use this remote control to operate the basic functions of your VCR. These functions  
include: play, record, rewind, fast-forward, stop, pause, channel scan, TV/VCR, power on, and  
power off.  
Move the selector switch to VCR to operate.  
• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other manufacturer’s  
brand VCR, please see the code chart and instructions on page 19.  
DVD Buttons  
You can also use this remote control to operate the basic functions of your DVD player. These  
functions include: play, rewind, fast-forward, stop, still/pause, previous/next, tray open/close, power  
on, and power off.  
Move the selector switch to DVD to operate.  
• The remote is preset with the code 000 to control JVC-brand DVD players. For any other  
manufacturer’s brand DVD player, please see the code chart and instructions on page 20.  
TV/CATV Switch  
Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to operate  
the television’s built-in tuner. Move the switch to CATV to operate a cable box.  
• See page 18 for information on programming your remote for cable box operation.  
VCR/DVD Switch  
You can control a VCRor DVDplayer with the buttons on the lower part of the remote control. Use the  
VCR/DVD selector switch to choose either VCRor DVD operation.  
• See pages 19 and 20 for information on programming your remote with VCR and DVD operating  
codes.  
Light  
Your remote control includes illuminated buttons for key features like CHANNEL+/- and VOLUME+/-. Press the  
LIGHTbutton to turn the illumination on.  
43  
Button Functions - PIP  
PIP displays two separate pictures on screen. Your television has 2-Tuner PIP, meaning you can  
view pictures from two different channels simultaneously. Aspecial set of PIPcontrol buttons are  
located on the upper part of the remote control. Descriptions of each button appear on this page.  
The PIP feature is available on series D502 models only.  
Cable Box Note  
The 2-Tuner PIPfunction may not operate when used with certain cable boxes. This is because while  
some models of cable box may receive up to 181 channels, they may only send the signal from one  
channel to your television (please also see diagram on page 11). For the PIPtuner to operate correctly, it  
must have access to all available channels. Since the television is receiving the signal of only one channel  
from the cable box, it is impossible for the 2-Tuner PIPto display a second, different channel.  
Because there are many different models of cable boxes in use today, if you are having problems  
operating your PIP feature with your cable box, we recommend you contact your local cable  
company for connection advice.  
On/Move  
Turn PIP on by pressing the ON/MOVE button.  
(PIP) ON/MOVE  
07  
02  
EXIT/PIP OFF to turn PIP off  
Once PIP is turned on, you can move the PIP window to any of the TV’s main picture’s four corners  
with the ON/MOVE button.  
ON/MOVE  
• Each press of ON/MOVE will shift the PIP window to a different corner.  
44  
Button Functions - PIP  
Freeze  
Use the FREEZE button to lock a single, still image onto the PIP window.  
• If PIP is off when FREEZE is pressed, a snapshot of the main screen is taken and placed in the  
PIPwindow.  
• If PIPis on when FREEZE is pressed, the image in the window when the button was pressed is held.  
Swap  
You can exchange the channel displayed on the main screen for the one shown in the PIP window  
by pressing SWAP.  
Channel +/- for PIP  
Like the main CHANNEL +/- buttons, CHANNEL +/- for PIP lets you scan through the channels in the  
PIP window.  
• Direct channel selection with the 10 key pad for PIPis not possible.  
Source  
You can select the signal source for the PIP window image.  
• If the PIP does not have a signal, the window will be blue.  
• If you connect a DVDto Video-2 the PIP window will be blue.  
NOTES:  
1
• The PIP window is / the size of the full screen.  
9
• PIPwill not display blocked channels or programs. A blue screen will display instead.  
45  
Troubleshooting  
46  
Warranty  
Parts  
Labor  
1 YEAR  
1 YEAR  
47  
Warranty  
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY. THIS WARRANTY DOES  
NOT APPLY FOR DETAILS OF REFURBISHED PRODUCT WARRANTY. PLEASE REFER  
TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH  
REFURBISHED PRODUCT.  
For customer use:  
Enter below the Model No. and Serial No.which is located either on the rear, bottom or side  
of the cabinet.  
Retain this information for future reference.  
Model No.:  
Serial No.:  
Purchase Date:  
Name Of Dealer:  
48  
Authorized Service Centers  
QUALITY  
SERVICE  
HOW TO LOCATEYOUR JVC SERVICE CENTER  
TOLL FREE: 1 (800) 537-5722  
Dear Customer,  
In order to receive the most satisfaction from your purchase, please read the  
instruction booklet before operating the unit. In the event that repairs are necessary,  
please call 1 (800) 537-5722 for your nearest authorized servicer or visit our website  
Remember to retain your Bill of Sale for Warranty Service.  
Do not service the television yourself  
Caution  
To prevent electrical shock, do not open the cabinet. There are no user serviceable parts  
inside. Please refer to qualified service personnel for repairs.  
Accessories  
To purchase accessories for your JVC product, please call toll free: 1 (800) 882-2345 or  
on the web at www.JVC.com  
For service in Canada  
To locate your local JVC service center or dealer in Canada please call:  
In Eastern Canada:  
1 (416) 293-1311  
In Western Canada:  
1 (604) 270-1311  
En Français (Montréal):  
1 (514) 871-1311  
Or visit us on the web at www.JVC.ca  
49  
Search Codes  
Cable/Satellite Search Codes Function:  
1) Slide the first 2-Way Mode Selector switch to CATV.  
2) Press the TV POWER and RETURN+ buttons. Hold for at least three seconds and release.  
3) Press TV POWER, see if the CATV or Satellite box responds.  
4) If there was a response, press RETURN+. The operating codes are now set. If there was no  
response, repeat Step 3. If you repeat Step 3 a total of 52 times without a response, use the  
remote control which came with the equipment.  
5) Press RETURN+ to exit.  
VCR Search Codes Function:  
1) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.  
2) Press the VCR POWER and RETURN+ buttons. Hold for at least three seconds and release.  
3) Press VCR POWER, see if the VCR responds.  
4) If there was a response, press RETURN+. The operating codes are now set. If there was no  
response, repeat Step 3. If you repeat Step 3 a total of 80 times without a response, use the  
manufacturers remote control which came with the VCR.  
5) Press RETURN+ to exit.  
DVD Player Search Codes Function:  
1) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.  
2) Press the DVD POWER and RETURN+ buttons. Hold for at least three seconds and release.  
3) Press DVD POWER, see if the DVDplayer responds.  
4) If there was a response, press RETURN+. The operating codes are now set. If there was no  
response, repeat Step 3. If you repeat Step 3 a total of 30 times without a response, use the  
manufacturers remote control which came with the DVD player.  
5) Press RETURN+ to exit.  
50  
Specifications  
Specifications subject to change without notice.  
51  
JVC COMPANYOF AMERICA  
Division of JVC Americas Corp.  
1700 Valley Road  
JVC CANADA, INC.  
21 Finchdene Square  
Scarborough, Ontario  
Canada, M1X 1A7  
Wayne, New Jersey, 07470  

IBM THINKCENTER 8187 User Manual
JVC INTERIART T V LINK AV 29FH1SUG User Manual
Lincoln IMPINGER 1000 User Manual
Memorex MPH7895 User Manual
Miele KM5956 User Manual
Palsonic 5160G User Manual
Panasonic CT 36G32 User Manual
Philips 1 09E+52 User Manual
Philips 107P2x User Manual
Philips DVP3258 User Manual