JVC AV 21FT User Manual

Specifications  
Model  
AV-21FT  
B, G, I, D, K, K1  
PAL, SECAM, NTSC 3.58 / 4.43 MHz (in VIDEO mode only)  
= 46.25 to 168.25 MHz  
VHF high channel (VH) = 175.25 to 463.25 MHz  
UHF channel (U) = 471.25 to 863.25 MHz  
AV-21AT  
COLOUR TELEVISION  
TV RF systems  
Colour systems  
Contents  
AV-21FT  
AV-21AT  
Channel and frequencies VHF low channel (VL)  
Locations ................................  
Preparation .............................  
Viewing a Television  
2
4
I Receives cable channels in mid band (X to Z, S1 to S10),  
super band (S11 to S20) and hyper band (S21 to S41) .  
Power input  
AC110 to 240 V, 50 / 60 Hz  
Programme ...........................12  
Power consumption  
Maximum 105 W, Average 68 W  
Screen size  
(measured diagonally)  
Picture tube 55 cm  
Visible area 51 cm  
Viewing Images from an  
External Device ....................14  
INSTRUCTIONS  
Thank you for purchasing this JVC  
colour television.  
To ensure your complete  
understanding, please read this  
manual thoroughly before operation.  
Audio output  
(Rated power output)  
5W (monaural)  
5W (monaural)  
Sound and Picture ...............15  
Other Features......................17  
Speakers  
(6 cm × 12 cm) oval × 2  
(5 cm × 9 cm) oval × 2  
External input / output  
VIDEO input (RCA)  
AUDIO input (RCA)  
Troubleshooting ...................23  
Specifications.........Back cover  
VIDEO output (RCA)  
AUDIO output (RCA)  
Headphone jack: mini jack (dia. 3.5 mm)  
Dimensions (W × H × D) 619 mm × 458 mm × 486.5 mm 502 mm × 451 mm × 480.5 mm  
WARNING:  
TO PREVENT FIRE OR SHOCK  
HAZARD, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR  
MOISTURE.  
Weight  
22 kg  
19.5 kg  
Accessories  
• Remote control unit: RM-C364 × 1  
• AA / R6 / UM-3 dry cell battery × 2  
Design and specifications subject to change without notice.  
CAUTION:  
TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES  
REGARDING THE USE OF THIS TV.  
Operate only from the power source specified on the TV.  
Avoid damaging the power plug and power cord.  
Avoid improper installation and never position this TV where good ventilation is  
unattainable. When installing this TV  
distance recommendations must be  
maintained between the floor and  
15 cm  
wall, as well as installment in a tightly  
enclosed area or piece of furniture.  
Adhere to the minimum distance  
10 cm  
10 cm  
15 cm  
guidelines shown for safe operation.  
Do not allow objects or liquid into the cabinet openings.  
In the event of a fault, unplug this TV and call a service technician. Do not  
attempt to repair it by yourself or remove the rear cover.  
When you dont use this TV for a long period of time, be sure to disconnect the  
power plug from the AC outlet.  
LCT0748-001A-H  
0400-Ki-AB-NV-JMT  
2000 VICTOR COMPANY OF JAPAN, LIMITED  
Preparation  
Preparation  
I Connecting other external devices  
1. Connecting the aerial and external devices  
Notes: .........................................................................................................................  
For further details, refer to the manuals provided with the devices you are connecting.  
Connecting cables are not supplied.  
The front and rear AUDIO/VIDEO input jacks are directly connected so that input to either  
jack is output through both.You cannot provide input to both the front and rear jacks at the  
same time. Disconnect one input, or use one of the jacks as an output jack only (for  
monitoring or recording).  
....................................................................................................................................  
To audio  
output  
To video  
output  
I Connecting the aerial and VCR  
If not connecting a VCR (video cassette recorder), do 1.  
If connecting aVCR, proceed 1 © 2 © 3.  
You can view images from the VCR without doing 3. For details, see To view  
images from a VCR connected to the TV with only an aerial cableon page 14.  
VIDEO AUDIO  
IN  
VCR (for playing)  
OUT  
VCR (for recording)  
VHF/UHF outdoor aerial  
To audio  
input  
To video  
input  
To video  
output  
Camcorder  
1
VIDEO AUDIO  
IN  
or  
TV game  
To audio  
output  
OUT  
2
3
To RF  
output  
To audio  
output  
To video  
output  
MENU  
VIDEO AUDIO  
IN  
Headphones  
To aerial input  
VCR  
1
Illustration of AV-21FT.  
Note: ..................................................................................................................  
Use headphones with a mini jack (dia. 3.5 mm). When using headphones, the speaker  
sound output is disabled.  
...........................................................................................................................  
Illustration of AV-21FT.  
5
4
Preparation  
Preparation  
5. Selecting the on-screen language  
2. Connecting the power cord  
You can select one of three languages for the on-screen display. The displayed  
menus on the screen are described in the selected language.  
Insert the Power plug into an AC outlet.  
In this manual, on-screen descriptions are given in English. Select ENGLISH.  
3. Inserting batteries into the remote control  
Correctly insert two batteries, observing the  
end first.  
and  
polarities and inserting the  
CHANNEL  
SCAN  
RETURN+  
- --  
/
0
DISPLAY  
MUTING  
CAUTION: ...........................................  
DISPLAY button  
Follow the cautions printed on the  
batteries.  
............................................................  
MENU  
MENU  
/
buttons  
MENU /+ buttons  
Notes: .................................................  
CHANNEL  
VOLUME  
Use AA/R6/UM-3 dry cell batteries.  
Battery life is approximately six months to  
one year depending on frequency of use.  
If the remote control operates erratically,  
replace the batteries.  
For details on menu operations using the front control buttons on the TV, see  
page 22.  
We recommend that you use the supplied  
batteries initially and replace them as  
soon as operation becomes erratic.  
The supplied batteries are for testing, not  
regular use.  
1. Press MENU  
to display the following menu.  
The following menu is displayed in one of three languages.  
/
............................................................  
ꢀꢁꢂꢃ  
3
MENU  
3
AUTO CH PRESET  
MANUAL CH PRESET  
Aꢄꢅꢆ ꢂꢇꢈꢅꢉꢆꢊꢋꢇ  
ꢉꢌꢍꢂꢇꢎ ꢂꢇꢈꢅꢉꢆꢊꢋꢇ  
LANGUAGE  
ENGLISH  
ꢎꢏꢐꢋ  
ꢉꢌꢈꢈꢋꢑꢊ  
4.Turning your TV on  
ꢄꢐꢒꢉꢇꢅꢓ  
ꢌꢖꢉꢇꢄꢗ -+  
ꢄꢐꢔꢆꢕ  
DISPLAY  
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
1. Press the Main power button on the TV to turn the TV’s main power  
on.  
English  
Chinese  
Russian  
Notes: ...................................................................................................................  
If a different menu is displayed, repeatedly press the MENU  
is displayed.  
If the menu appears in English, the TVs on-screen language is already set to English, so  
you can skip steps 2 and 3.  
..............................................................................................................................  
The POWER lamp lights.  
button until this menu  
/
If image does not appear:  
Your TV is in the standby mode. Press the POWER button on the remote control  
to turn your TV on.  
You can also turn on your TV by pressing the CHANNEL  
/
button on your  
TV.  
2. Press MENU  
menu.  
to select the third item on the  
/
MENU  
AUTO CH PRESET  
MANUAL CH PRESET  
3
To turn your TV off:  
Press the POWER button on the remote control.Your TV enters the standby  
mode.  
LANGUAGE  
ENGLISH  
3. Press MENU /+ to select ENGLISH.  
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
To turn the TV’s main power off:  
Press the Main power button on the TV. The POWER lamp goes off.  
The menu is displayed in English.  
4. Proceed to 6. Presetting TV stationson the following page.  
If you want to complete operations at this stage, press the DISPLAY button to  
turn the menu display off.  
7
6
Preparation  
Preparation  
I Manual Channel Preset  
You can manually preset the desired TV stations to the desired channels.  
6. Presetting TV stations  
To view a TV programme, you must first preset TV stations to channels on the TV.  
This TV has 100 channels (channel 1 to 99 and channel AV).  
You can choose between two functions, the Auto Channel Preset and Manual  
Channel Preset and preset TV stations to channels on TV.  
1. Press MENU  
PRESET.  
to select MANUAL CH  
/
MENU  
AUTO CH PRESET  
MANUAL CH PRESET  
3
LANGUAGE  
ENGLISH  
If a different menu is displayed, repeatedly press the  
MENU button until this menu is displayed.  
Note: ...........................................................................................................................  
/
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
After you have finished presetting, you can set undesired channels to be skipped over, see  
page 11.  
....................................................................................................................................  
2. Press MENU /+.  
MANUAL  
FINE  
SKIP  
The sub-menu is displayed.  
NO  
B/G  
SOUND SYSTEM  
EXIT  
The channel No. is displayed as a PR No. For  
example, channel 1 will be displayed as PR 1.  
However, channel AV will be displayed as AV.  
DISPLAY  
MUTING  
Channel  
No.  
SELECT BY  
PROGRAM BY -+  
SEARCH BY VOL-+ DISPLAY  
PR 1 VL  
EXIT BY  
DISPLAY button  
MENU  
MENU  
/
buttons  
MENU /+ buttons  
3. Press MENU /+ to select the channel No. to be preset.  
CHANNEL  
VOLUME  
VOLUME /+ buttons  
REMOTE CONTROL UNIT  
RM-C364  
4. Press VOLUME /+ to start selection of the TV station.  
or  
is displayed on the screen.  
When a TV station is received, the  
or  
display goes out, and the TV  
station is preset to the currently selected channel No.  
I Auto Channel Preset  
You can automatically preset all TV stations that can be received on your TV to  
channels in one simple operation.  
If you have selected the wrong TV station for preset, repeatedly press the  
VOLUME /+ button until the desired TV station is selected.  
To stop the Manual Channel Preset, press any button other than the VOLUME  
/+ button.  
Notes: .........................................................................................................................  
When you use this function, no station is preset to the channel AV.  
Channel AV is offered for viewing images from a VCR connected to your TV with only an  
aerial cable. For more details, see page 14.  
If the Auto Channel Preset does not work well, preset TV stations manually, see page 9.  
....................................................................................................................................  
If the picture is not clear:  
Use the Fine function to fine-tune the TV station.  
1. Press MENU  
to select FINE.  
/
MANUAL  
FINE  
SKIP  
SOUND SYSTEM  
EXIT  
NO  
B/G  
2. Hold VOLUME /+ down to fine-tune the TV  
station so that the best image is displayed on  
screen.  
1. Press MENU  
to select AUTO CH PRESET.  
If a different menu is displayed, repeatedly press the  
MENU button until this menu is displayed.  
MENU  
AUTO CH PRESET  
MANUAL CH PRESET  
3
/
LANGUAGE  
ENGLISH  
SELECT BY  
PROGRAM BY -+  
FINE  
PR 3 VL  
EXIT BY  
BY VOL-+ DISPLAY  
/
or indicates that the TV station is being  
fine-tuned.  
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
2. Press MENU /+ to start the Auto Channel  
Preset function.  
ON SEARCH is displayed on the screen.  
When you have finished presetting all TV channels that can be received on your  
TV, the display will go out and the Auto Channel Preset function will end.  
To stop the Auto Channel Preset, press the MENU /+ button.  
Continued on next page.  
9
8
Preparation  
Preparation  
I Skip  
MANUAL  
FINE  
SKIP  
SOUND SYSTEM  
EXIT  
5. Press MENU  
to select SOUND SYSTEM.  
/
When selecting channels, you can set undesired channels to be skipped.  
NO  
B/G  
Channels set to be skipped cannot be selected by the CHANNEL  
the CHANNEL SCAN button.  
Channels to which a station has not been preset are automatically set to be  
/
buttons nor  
6. Press VOLUME /+ to select the appropriate  
sound system.  
SELECT BY  
PROGRAM BY -+  
CHANGE BY VOL-+ DISPLAY  
PR 3 VL  
EXIT BY  
For the sound systems in each country or region, refer  
to the table The Broadcasting systems of Each  
country or Region.  
skipped.  
1. Press MENU  
PRESET.  
to select MANUAL CH  
/
MENU  
AUTO CH PRESET  
MANUAL CH PRESET  
3
LANGUAGE  
ENGLISH  
7. Press MENU  
to select MANUAL.  
/
If a different menu is displayed, repeatedly press the  
MENU button until this menu is displayed.  
/
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
8. Repeat steps 3 to 7 if you want to preset another TV station to a  
channel.  
2. Press MENU /+.  
MANUAL  
FINE  
SKIP  
SOUND SYSTEM  
EXIT  
The sub-menu is displayed.  
NO  
B/G  
9. Press DISPLAY to turn the display off.  
SELECT BY  
PROGRAM BY -+  
PR 1 VL  
EXIT BY  
SEARCH BY VOL-+ DISPLAY  
3. Press MENU  
to select SKIP.  
/
MANUAL  
FINE  
SKIP  
SOUND SYSTEM  
EXIT  
NO  
B/G  
The channel No. is displayed as a PR No. For  
example, channel 1 will be displayed as PR 1.  
However, channel AV will be displayed as AV.  
Channel  
No.  
SELECT BY  
PROGRAM BY -+  
YES/NO BY VOL-+ DISPLAY  
PR 1 VL  
EXIT BY  
The Broadcasting Systems of Each Country or Region  
System  
Area  
Country or Region  
4. Press MENU /+ to select the channel you want to skip.  
Sound  
Colour  
Bahrain, Kuwait, Oman, Qatar,  
United Arab Emirates, Yemen, etc.  
Indonesia, Malaysia, Singapore,  
Thailand, India, etc.  
MANUAL  
FINE  
SKIP  
SOUND SYSTEM  
EXIT  
5. Press VOLUME /+ to select YES.  
PAL  
B/G  
The channel you selected is set to be skipped.  
YES  
B/G  
Asia,  
Middle  
East  
To cancel the Skip:  
select NO.  
SELECT BY  
PROGRAM BY -+  
YES/NO BY VOL-+ DISPLAY  
PR 5 VL  
EXIT BY  
China, Vietnam, etc.  
PAL  
PAL  
D/K  
I
Hong Kong, etc.  
6. Repeat steps 4 and 5 if you want to set another  
channel to skip.  
Islamic Republic of Iran, Lebanon,  
Saudi Arabia, etc.  
SECAM  
B/G  
Russia, etc.  
SECAM  
PAL  
D/K  
D/K  
B/G  
I
Czech Republic, Poland, etc.  
Germany, Holland, Belgium, etc.  
UK, etc.  
7. Press DISPLAY to turn the display off.  
Europe  
PAL  
PAL  
Oceania  
Africa  
Australia, New Zealand, etc.  
Republic of South Africa, etc.  
Nigeria, etc.  
PAL  
B/G  
I
PAL  
PAL  
B/G  
B/G  
Egypt, Morocco, etc.  
SECAM  
11  
10  
Viewing a Television Programme  
Viewing a Television Programme  
3. Press VOLUME /+ to adjust  
4. To turn your TV off, press  
2. Select a channel.  
the sound.  
VOLUME  
POWER.  
I Up/ down selection  
POWER  
1. Press CHANNEL  
/
.
ECO  
POWER  
CHANNEL  
SENSOR  
SYSTEM  
COLOUR SOUND  
If the sound is abnormal:  
Repeatedly press the SOUND  
SYSTEM button to select the  
appropriate sound system. For  
details, see Sound Systemon  
page 15.  
PICTURE  
MODE  
Note: .............................................  
Note: .............................................  
We recommend that you press the  
Main power button on the TV to turn  
the main power off if you do not plan  
to use your TV for a long time or if you  
wish to save energy.  
1
2
3
6
9
TV/VIDEO  
Up/down selection cannot be selected  
for channels to which the Skip has  
been set to YES. (See page 11.)  
4
5
8
0
......................................................  
OFF  
7
TIMER  
......................................................  
SYSTEM  
COLOUR SOUND  
CHANNEL  
SCAN  
RETURN+  
- --  
/
I Direct selection  
1. Repeatedly press the -/--  
button to select the desired  
mode then press the  
Number buttons.  
DISPLAY  
MUTING  
MENU  
1
4
7
2
5
8
0
3
6
9
CHANNEL  
VOLUME  
REMOTE CONTROL UNIT  
RM-C364  
Using the buttons on the TV  
- --  
/
Condition:...........................................................................................................  
Check to make sure the Child Lock function is set to OFF. When the Child Lock  
function is set to ON, the TV cannot be operated using the front control buttons. For  
details, see Child Lockon page 20.  
- : 1-digit mode  
(example)  
Channel 6 © Press 6.  
Channel AV © Press 0.  
.............................................................................................................................  
1. Press CHANNEL  
turn your TV on.  
to  
3. Press VOLUME /+ to  
/
adjust the sound.  
- - : 2-digit mode  
(example)  
1. Press POWER to turn your  
CHANNEL  
VOLUME  
EXIT  
Channel 6 © Press 0, 6.  
Channel 16 © Press 1, 6.  
Channel AV © Press 0, 0.  
TV on.  
POWER  
Note: ...........................................  
If your TV does not turn on, press  
the Main power button and then  
press the CHANNEL  
again.  
....................................................  
To turn your TV off:  
Press the Main power button to turn  
the main power off. The POWER  
lamp goes off.  
Notes: ...........................................  
If the colour is abnormal:  
Repeatedly press the COLOUR  
SYSTEM button to select the  
appropriate colour system. For  
details, see Colour Systemon  
page 15.  
/
button  
If your TV does not turn on, press the  
Main power button on the TV then  
press the POWER button again.  
You can also turn on your TV by  
pressing any of the following buttons;  
POWER  
2. Press CHANNEL  
select a channel.  
to  
/
/
the CHANNEL  
the Number buttons  
button  
SYSTEM  
COLOUR SOUND  
If you press the Main power button  
again, your TV turns on immediately.  
Step 1 is no longer required.  
the TV/VIDEO button  
......................................................  
CHANNEL  
Illustration of AV-21FT.  
13  
12  
Sound and Picture  
Viewing Images from an External Device  
You can view images from VCRs or other external devices connected to your TV.  
Sound System  
If the sound is abnormal, select the  
appropriate sound system. Each press  
of the SOUND SYSTEM button  
To select the VIDEO mode  
via MENU operation:  
1. Press TV/VIDEO to select the  
ECO  
POWER  
SENSOR  
VIDEO mode.  
SYSTEM  
COLOUR SOUND  
PICTURE  
MODE  
TV/VIDEO  
1. Press MENU  
to  
/
changes the sound system as follows.  
1
2
5
3
6
TV/VIDEO  
display the MENU 1 and  
select INPUT.  
TV mode  
VIDEO mode  
VIDEO  
B/G  
I
D/K  
4
Channel  
number  
Notes: .................................................  
MENU  
or AV  
For the sound systems in each country or  
region, see the table The Broadcasting  
Systems of Each Country or Regionon  
page 10.  
You cannot select any sound system  
when in VIDEO mode.  
............................................................  
Colour System  
TV mode:  
This mode is for viewing TV  
programmes. Press the TV/VIDEO  
MENU  
1
If the colour is abnormal, select the  
appropriate colour system. Each press  
of the COLOUR SYSTEM button  
INPUT  
TV  
ON TIMER  
PR 1 0:00  
OFF  
/
VNR  
button, or press the CHANNEL  
buttons, or press the number  
buttons to return to this mode.  
changes the colour system as follows.  
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
Picture Mode  
I
n TV mode (channel 1 to 99 and AV):  
2. Press MENU /+ to select  
To view images from a VCR  
connected to the TV with only  
an aerial cable:  
Your VCR must be preset to the  
channel AV of this TV.  
SECAM  
You can select one of three picture  
adjustment modes.  
Repeatedly press the PICTURE  
MODE button to select the desired  
mode.  
AUTO  
PAL  
the VIDEO mode.  
In VIDEO mode:  
MENU  
SECAM  
AUTO  
PAL  
Thoroughly read the manual of  
your VCR, and preset your VCR to  
the channel AV using the Manual  
Channel Preset function on page 9.  
As a result, you can view images  
from your VCR when you select the  
channel AV in the TV mode.  
NTSC4.43  
NTSC3.58  
BRIGHT:  
Heightens contrast and sharpness.  
TV mode changes to VIDEO  
mode.  
AUTO:  
Automatic colour system selection.  
STANDARD:  
Standardizes picture adjustments.  
Notes: .................................................  
SOFT:  
For the colour systems in each country or  
region, see the table The Broadcasting  
Systems of Each Country or Regionon  
page 10.  
Softens contrast and sharpness.  
If the colour is abnormal:  
Repeatedly press the COLOUR  
SYSTEM button to select the  
appropriate colour system. For  
details, see Colour Systemon  
page 15.  
Note: ...................................................  
If the colour is abnormal even though you  
selected AUTO, change the appropriate  
colour system manually.  
Pressing the PICTURE MODE button  
returns all the picture settings in the  
MENU 4 menu to their default settings.  
............................................................  
............................................................  
15  
14  
Other Features  
Sound and Picture  
Display  
Eco Sensor  
Muting  
You can continuously display the  
current channel number or VIDEO  
mode on the screen.  
Press the DISPLAY button.  
To turn the display off, press the  
DISPLAY button again.  
You can adjust this TV so that the  
screen automatically adjusts to the  
optimum contrast according to the  
brightness of your room. This function  
reduces eye strain and the power  
consumption of this TV.  
You can turn the volume off instantly.  
This is convenient when answering the  
phone or when you have visitors.  
Press the MUTING button.  
To return the sound, press the  
MUTING button again.  
ECO  
POWER  
SENSOR  
SYSTEM  
COLOUR SOUND  
PICTURE  
MODE  
1
2
5
8
0
3
6
9
TV/VIDEO  
4
Repeatedly press the ECO SENSOR  
button to select the desired mode.  
OFF  
7
TIMER  
Note: ...................................................  
When selecting a channel or VIDEO mode  
with no input signal, indication of selected  
channel or VIDEO mode becomes fixed  
on the screen.  
CHANNEL  
SCAN  
RETURN+  
- --  
/
Picture Adjustment  
ECO SENSOR DISPLAY:  
The Eco Sensor function will work.  
In this mode, the heart mark  
indicating the brightness of your room  
is displayed for several seconds each  
time the brightness changes. The  
number of heart marks displayed on  
screen increases as your room  
becomes darker.  
DISPLAY  
MUTING  
You can adjust the picture as you like.  
............................................................  
1. Press MENU  
repeatedly  
to display the MENU 4.  
/
MENU  
CHANNEL  
VOLUME  
MENU  
4
Off Timer  
TINT  
COLOUR  
BRIGHT  
CONT.  
SHARP  
You can set this TV to turn off  
automatically within a specified period  
of time.  
Repeatedly press the OFF TIMER  
button to select the period of time.  
REMOTE CONTROL UNIT  
RM-C364  
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
ECO SENSOR:  
The Eco Sensor function will work.  
However, in this mode, the heart mark  
will not be displayed even if the  
brightness of your room changes.  
2. Press MENU  
to select an  
item and press MENU /+ to  
/
adjust it.  
You can set the period of time a  
maximum of 120 minutes in 10  
minute increments.  
1 minute before the Off Timer turns  
off the TV, GOOD NIGHT! displays.  
Item  
+
Reddish  
TINT (tint)  
Greenish  
ECO SENSOR OFF:  
The Eco Sensor function will not work.  
Lighter COLOUR (colour depth) Deeper  
Darker  
Lower  
Softer  
BRIGHT (brightness) Brighter  
CONT. (contrast) Higher  
SHARP (sharpness) Sharper  
To display the remaining time:  
Press the OFF TIMER button once.  
To cancel the Off Timer:  
Press the OFF TIMER button to return  
the period of time to 0.  
Note: .............................................  
TINT (tint) is displayed only when  
viewing images from NTSC3.58 or  
NTSC4.43 colour systems.  
......................................................  
Note: ...................................................  
The Off Timer will not turn off the TVs  
main power.  
............................................................  
3. Press DISPLAY to turn the  
display off.  
17  
16  
Other Features  
Other Features  
5. Press DISPLAY to turn the  
display off.  
Return +  
On Timer  
By setting a channel to Return  
channel, you can return to that  
channel with one touch.  
Your TV will automatically turn on and  
tune into the channel you want after a  
certain period of time you have  
specified.  
ECO  
POWER  
SENSOR  
6. Press POWER to turn the TV  
off.  
SYSTEM  
COLOUR SOUND  
PICTURE  
MODE  
The ON TIMER lamp will stay lit.  
1
2
3
6
9
TV/VIDEO  
/
1. Press CHANNEL  
or the  
Notes: ...........................................  
Number buttons to select a  
channel to set to Return  
channel.  
4
5
8
0
1. Press MENU  
repeatedly  
/
If you turn off the TVs main power by  
pressing the Main power button, the  
On Timer setting is canceled.  
If you do not turn off the TV after  
starting the On Timer, once the time  
set for the On Timer is reached, the  
channel will automatically switch to  
the channel set for the On Timer.  
......................................................  
to display the MENU 1.  
OFF  
7
TIMER  
2. Press MENU  
ON TIMER.  
to select  
/
CHANNEL  
SCAN  
RETURN+  
- --  
/
2. Press RETURN + for more  
than 3 seconds continuously.  
RETURN PLUS PROGRAMMED!  
appears.  
DISPLAY  
MUTING  
MENU  
INPUT  
ON TIMER  
1
TV  
Channel  
No.  
PR 1 0:00  
OFF  
MENU  
VNR  
3. When viewing another  
channel, press RETURN +.  
The channel changes to the  
channel set for Return channel.  
PROGRAM BY -+  
SELECT BY  
OPERATE BY VOL-+ DISPLAY  
EXIT BY  
CHANNEL  
VOLUME  
While the On Timer is operating:  
The ON TIMER lamp lights.  
3. Press MENU /+ to select a  
channel you want to view  
when the TV turns on.  
REMOTE CONTROL UNIT  
RM-C364  
When the time set for the On  
Timer is reached:  
The TV automatically turns on and the  
channel set for the On Timer is  
displayed.  
To cancel the channel set for  
Return channel:  
Press the RETURN + button for more  
than 3 seconds continuously.  
RETURN PLUS CANCELLED!  
appears.  
Note: .............................................  
You cannot select the channel AV, the  
VIDEO modes, and the channels for  
which the Skip is set (See page 11).  
......................................................  
Channel Scan  
Notes: .................................................  
For safety reasons the TV will  
You can search for the channel you  
want to view while scanning all of the  
channels that can be viewed on this  
TV.  
automatically turn off if no operations are  
made within approximately two hours after  
the TV is turned on with the On Timer.  
The Off Timer and Auto Shutoff have  
priority over the On Timer.  
Notes: .................................................  
When you turn the TV off, the Return  
channelsetting will be canceled.  
When you press the RETURN + button  
while viewing the channel set for Return  
channel, the channel changes to the  
previously viewed channel.  
4. Press VOLUME /+ to select  
the period of time after which  
you want to turn on the TV.  
The ON TIMER lamp lights and the  
On Timer starts.  
............................................................  
1. Press CHANNEL SCAN.  
Channels will be scanned in  
channel No. order.  
Each time you press the button,  
the period of time changes in 15  
minute intervals (up to 12 hours).  
When you press the RETURN + button  
while in a VIDEO mode, the mode  
switches to TV mode. To return to the  
channel set for Return channel, press  
the RETURN + button again.  
2. When the channel that you  
want to view appears, press  
CHANNEL SCAN again  
before scanning for the next  
channel begins.  
MENU  
1
INPUT  
TV  
ON TIMER  
VNR  
............................................................  
PR 3 11:00  
OFF  
PROGRAM BY -+  
SELECT BY  
When there is no setting for  
Return channel:  
When you press the RETURN +  
button, the channel changes to the  
previously viewed channel.  
EXIT BY  
OPERATE BY VOL-+ DISPLAY  
Note: ...................................................  
To cancel the On Timer:  
Press the VOLUME /+ button to  
return the period of time to 0:00.  
Channel Scan selection cannot be  
selected for channels to which the Skip  
has been set to YES. (See page 11.)  
............................................................  
18  
19  
Other Features  
Other Features  
Child Lock  
Auto Shutoff  
Blue Back  
4
5
8
0
6
9
OFF  
7
TIMER  
You can disable the front control  
buttons of the TV.  
When this function is set to ON, the TV  
can be operated using only the remote  
control.  
Use this function to prevent children  
from operating the TV at their own  
discretion (without parental consent).  
You can set your TV to turn off if no  
signals are received for about 15  
minutes or longer after the end of a  
broadcast.  
You can mute the sound and change  
the picture into a blue screen while no  
signals come into the TV, or when the  
input signals are unstable.  
CHANNEL  
SCAN  
RETURN+  
- --  
/
DISPLAY  
MUTING  
1. Press MENU  
repeatedly  
1. Press MENU  
repeatedly  
/
/
MENU  
to display the MENU 2.  
to display the MENU 2.  
2. Press MENU to select  
AUTO SHUTOFF.  
2. Press MENU  
BLUE BACK.  
to select  
/
/
CHANNEL  
VOLUME  
1. Press MENU  
repeatedly  
/
MENU  
AUTO SHUTOFF  
CHILD LOCK  
BLUE BACK  
2
MENU  
AUTO SHUTOFF  
CHILD LOCK  
BLUE BACK  
2
REMOTE CONTROL UNIT  
RM-C364  
to display the MENU 2.  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
2. Press MENU  
CHILD LOCK.  
to select  
/
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
MENU  
AUTO SHUTOFF  
CHILD LOCK  
BLUE BACK  
2
OFF  
OFF  
ON  
VNR  
3. Press MENU /+ to select ON.  
3. Press MENU /+ to select ON.  
(Video Noise Reduction)  
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
AUTO SHUTOFF  
ON  
BLUE BACK  
ON  
You can reduce the picture noise.  
ON:  
ON:  
3. Press MENU /+ to select ON.  
1. Press MENU  
repeatedly  
/
Activates the Auto Shutoff.  
OFF:  
Activates the Blue Back.  
OFF:  
to display the MENU 1.  
CHILD LOCK  
ON  
2. Press MENU  
VNR.  
to select  
/
Cancels the Auto Shutoff.  
Cancels the Blue Back.  
ON:  
Notes: ...........................................  
Activates the Child Lock, disabling  
operation of the TV using the front  
control buttons.  
4. Press DISPLAY to turn the  
display off.  
MENU  
INPUT  
ON TIMER  
1
TV  
To view a broadcast even when the  
reception signal is poor, set the Blue  
Back to OFF.  
PR 1 0:00  
OFF  
VNR  
Notes: .................................................  
The Auto Shutoff function does not turn off  
the TVs main power.  
The Auto Shutoff will not work for a  
VIDEO mode.  
............................................................  
OFF:  
Even when the Blue Back is set to  
OFF, the sound may not be audible.  
The Blue Back function does not  
operate in VIDEO mode.  
SELECT BY  
OPERATE BY -+  
EXIT BY  
DISPLAY  
Cancels the Child Lock.  
4. Press DISPLAY to turn the  
display off.  
3. Press MENU /+ to select ON.  
......................................................  
VNR  
ON  
Note: ...................................................  
4. Press DISPLAY to turn the  
display off.  
The Child Lock is canceled when you turn  
the TVs main power off.  
............................................................  
ON:  
Activates the VNR. Select ON  
when viewing a noisy picture.  
OFF:  
Cancels the VNR.  
4. Press DISPLAY to turn the  
display off.  
20  
21  
Troubleshooting  
Other Features  
Important: Review all the instructions in this manual.  
2. Repeatedly press MENU to  
select the desired function or  
item.  
Problem  
Check/Action  
Cannot turn TV on  
Press the Main power button (see p.6).  
Insert the power plug in an AC outlet.  
To select a function or item  
above the currently selected  
function or menu:  
Repeatedly press the MENU button  
to proceed to another menu, and  
then repeatedly press the MENU  
button again to return to the  
original menu. Then select the  
function or item.  
No picture nor sound  
Press the TV/VIDEO button to select the correct mode (see  
p.14).  
Check the aerial connections.  
Remote control inoperable Replace the batteries (see p.6).  
Insert the batteries correctly.  
Buttons on front of TV do  
not work  
Is the Child Lock function ON ? (see p.20).  
The TV turns on suddenly The TV will automatically turn on when the On Timer is  
operated (see p.19).  
MENU /+ buttons  
The TV turns off suddenly The TV will automatically turn off in the following cases.  
When the Off Timer or Auto Shutoff is operated (see p.17  
and p.21).  
3. Press MENU /+ or VOLUME  
/+ to carry out the desired  
operation.  
MENU  
CHANNEL  
VOLUME  
EXIT  
When no operations are made within approximately two hours  
after the TV was turned on with the On Timer (see p.19).  
Abnormal sound  
Abnormal colour  
Select the appropriate sound system (see p.15).  
For details, see the description  
for the respective function.  
Adjust the colour and brightness (see p.16).  
Select the appropriate colour system (see p.15).  
Set the Picture mode to STANDARD (see p.15).  
MENU button  
VOLUME /+  
(EXIT) buttons  
4. Press VOLUME /+ to turn the  
Lines or streaks in picture  
(interference)  
Move the components apart until the interference disappears.  
Reposition the aerial.  
menu display off.  
Illustration of AV-21FT.  
Spotted picture (crosstalk) Move the aerial away from the source of interference.  
Replace the aerial cable with a coaxial cable, which is less  
prone to interference.  
If the sub-menu is displayed:  
The sub-menu cannot be turned off  
by the VOLUME /+ button when it  
is displayed. Follow the procedure  
below to turn the sub-menu display  
off.  
Menu operations using  
the buttons on the TV  
Double picture (ghost)  
Reposition the aerial.  
Replace with an aerial with good directionality.  
Snowy picture  
(image noise)  
Check the aerial connection and aim it correctly.  
Replace or repair the aerial.  
You can operate functions in menus  
using the front control buttons on the  
TV without having to use the remote  
control.  
The TV channel changes  
suddenly  
The channel will automatically be changed when the On Timer  
operates (see p.19).  
1. Press MENU to select EXIT.  
MANUAL  
FINE  
The screen turns blue  
Is the Blue Back set to ON ? (see p.21).  
SKIP  
NO  
Condition: ..........................................  
SOUND SYSTEM  
EXIT  
B/G  
The following are normal occurrences and are not the result of TV  
malfunctions:  
When a still bright image (of a white dress, for example) appears on the screen, the image  
may be coloured. This problem occurs in all CRTs, and when the bright image disappears,  
the colouration also disappears.  
This TV is equipped with a microcomputer that may operate abnormally due to interference  
from external devices. If this happens, press the Main power button to turn the main power  
off and disconnect the power plug from the AC outlet. Then, reconnect the power plug to the  
AC outlet and press the Main power button again.  
Check to make sure the Child Lock  
function is set to OFF. When the Child  
Lock function is set to ON, the TV cannot  
be operated using the front control  
buttons. For details, see Child Lockon  
page 20.  
SELECT BY  
PROGRAM BY -+  
EXIT  
PR 1 VL  
EXIT BY  
BY VOL-+ DISPLAY  
2. Press VOLUME /+ to turn the  
............................................................  
sub-menu display off.  
1. Press MENU to display the  
menu.  
If the desired menu is not  
displayed:  
Repeatedly press the MENU button  
until the desired menu is displayed.  
23  
22  

IBM G94 User Manual
JVC AV 28KH1SUF User Manual
Konica Minolta Computer Hardware PCI 1712L User Manual
Lenovo J SERIES 3000 User Manual
LG Electronics 90M User Manual
LG Electronics CINEMA 3D MONITOR D2342P User Manual
Maxtor Personal Storage 5000LE User Manual
Palsonic 6830GY User Manual
Philips 17GR2740 User Manual
Philips PET741W User Manual