Elo TouchSystems AMM19TK User Manual

AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 1  
back of the monitor  
WARN IN G  
The title "WARNING" is used to inform the users of  
possible causes that could inflict the injury, death, or  
property damage to the patients.  
CAUTION  
The title "CAUTION" is used to inform the users of  
possible causes that could inflict the patients although  
it might not severe enough to cause deaths.  
NOTE  
The title "NOTE" is used to inform the users of items  
that are of importance in terms of installation,  
operation, or maintenance of the Equipment although  
the failure does not inflict the bodily harm to the  
patients.  
ADAVN INT’LCORP.2003  
“ELO” is a Registered trademark of Elo TouchSystems, Inc.,  
All other trademarks are the property of their reference owners.  
This document is subject to change without notice.  
Advan provides this information as reference only. Reference to other vendor’s products  
does not imply any recommendation or endorsement.  
Revision Control  
Date  
Description  
Document number  
Rev. 4 112003  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 3  
Quick Setup (IBM/IBM Compatible under Windows 95/98/ME/2000)  
Please Read Carefully When Setting Up Your New Monitor  
Monitor Screen Adjustment and Resolution Setting Procedure for IBM/IBM Compatible  
Computers with Windows based OS system.  
Before adjusting the monitor, all the necessary drivers should be installed to your System  
and resolution has to be set to manufacturer’s recommended preset of 1280 x 1024 @ 60Hz,  
70Hz, 72Hz or 75 Hz.  
To check the resolution, press the “SELECT UP” button on the monitor and the “Information”  
will display under the OSD. Information will have Resolution, Horizontal and Vertical (Refresh  
rate) frequency information.  
To change the resolution to its factory recommended preset.  
1. On a Windows 95, 98, ME or 2000, press right button on a Mouse to execute the Pop-up  
menu.  
2. Press Properties” to execute the “Display Properties”  
3. Press Setting” and change the resolution to 1280 x 1024.  
4. Press Apply or OK” to select and press “OK” to keep the selected resolution.  
5. Go back to “Display Properties” - “Setting” - “Advanced properties” - “Adapter”  
6. On Adapter property, change the refresh rate to 60Hz, 70Hz, 72Hz or 75Hz. If you don’t  
have these options, choose “Adapter Default”. (60Hz recommended)  
Screen Adjustment Procedure  
1. Press the “AUTO” button.  
2. If you still don’t have a clear display monitor, please refer to step 3.  
3. Start Shut Down” in Windows 95/98/ME/2000 - It will display moire on screen  
4. Press Up” or “Down” button then the OSD menu will pop-up.  
5. Adjust the “Frequency” under the OSD to reduce or get rid of the vertical display noise  
(Jail bars). (Page 16)  
6. Once the vertical display noise disappears, press adjust the “Phase” to reduce or get rid of  
the horizontal display noise (Snowy effect). (Page 16)  
4
User’s Guide  
Quick Setup (IBM/IBM Compatible under Windows NT 4.0)  
Please Read Carefully When Setting Up Your New Monitor  
Monitor Screen Adjustment and Resolution Setting Procedure for IBM/IBM Compatible  
Computers with Windows based OS system.  
Before adjusting the monitor, all the necessary drivers should be installed to your System  
and resolution has to be set to manufacture’s recommended preset of 1280 x 1024 @ 60Hz,  
70Hz, 72Hz or 75Hz.  
To check the resolution, press the “SELECT UP” button on the monitor and the “Information”  
will display under the OSD. Information will have Resolution, Horizontal and Vertical (Refresh  
rate) frequency information.  
To change the resolution to its factory recommended preset.  
1. On a Windows NT 4.0, press right button on a Mouse to execute the Pop-up menu.  
2. Press Properties” to execute the “Display Properties”  
3. Press Setting” and change the resolution to 1280 x 1024.  
4. Change Refresh Frequency” to 60Hz, 70Hz, 72Hz or 75Hz. (60Hz recommended)  
Screen Adjustment Procedure  
1. Press the “AUTO” button.  
2. If you still don’t have a clear display monitor, please refer to step 3.  
3. Start Shut Down” in Windows 95/98/ME/2000 - It will display moire on screen  
4. Press Up” or “Down” button then the OSD menu will pop-up.  
5. Adjust the “Frequency” under the OSD to reduce or get rid of the vertical display noise  
(Jail bars). (Page 16)  
6. Once the vertical display noise disappears, press adjust the “Phase” to reduce or get rid of  
the horizontal display noise (Snowy effect). (Page 16)  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 5  
Quick Setup (Macintosh)  
Please Read Carefully When Setting Up Your New Monitor  
1. Set your Macintosh Adapter on pages 23 and 24.  
2. Push the “APPLE” icon on the upper left corn and execute Control Panel->  
Monitors&Sound. Select Thousands” for the Color Depth, Select “1280X1024, 60Hz,  
70Hz, 72Hz or 75Hz” for the Resolution. (60Hz recommended)  
*
On some Apple G3 or newer systems, you may not need to use the Macintosh Adapter.  
Screen Adjustment Procedure  
1. Press the “AUTO” button on the monitor.  
6
User’s Guide  
INTRODUCTION  
Congratulations on your purchasing of the AMM17TK/AMM18TK/AMM19TK high  
performance TFT LCD monitor.  
FEATURES  
The FPD is a TFT-LCD monitor that is intelligent, microprocessor-based and ergonomically  
designed display, compatible with most analog RGB (Red, Green, Blue) display standards,  
including PS/V, PS/2, Apple Macintosh Centris, Quadra, and Macintosh II family signals. The  
LCD monitor is capable of displaying crisp and vibrant color graphics with VGA, SVGA, XGA,  
SXGA (non-interlaced), and most Macintosh compatible color video cards.  
Advanced Viewing Solution (AVS): Our sophisticated filter extends the viewing angle of  
the screen image, without sacrificing contrast ratio and brightness.  
AdvancedTiming Setup (ATS): Aunique technology from the One TouchAutoAdjustment.  
Pressing the Auto Adjust button on the front panel, automatically optimizes position,  
phase, clock, contrast and color balance. This allows the user to maximize the perfect  
screen setting in the shortest amount of time.  
Advanced Mounting Solution (AMS): Improve flat panel environment, utilizing numerous  
ergonomic mounting solutions to allow creative use in conjunction to product application.  
The monitor is able to properly function even in case of upgrade video cards or software  
because of the wide auto-scanning compatibility range without requiring to buy a new  
monitor.  
The internal microprocessor digitally controls auto-scanning. For horizontal scan  
frequencies between 24.8 KHz and 60.2 KHz, and vertical scan frequencies between  
56.3 Hz and 85.1 Hz. In each frequency mode, the microprocessor-based circuitry allows  
the monitor to function at the precision-of a fixed frequency.  
The resident memory allows for storing factory default settings and also additional user  
adjustment parameters.  
The maximum resolution achievable is SXGA (1280 x 1024), best suited for Windows  
applications  
The compact and sleek cabinet design saves lot of your desk space and makes your desk  
look neat and tidy.  
The monitor is compliant with VESA-DPMS power management standard. In order to  
save energy, the monitor must be connected to a system compliant with the standard.  
The monitor is also compliant with the most stringent environmental scheme of TCO  
95. In this scheme, no environmental harmful substances are used during the entire  
manufacturing process.  
The monitor is certified by UL International to medical standard UL2601-1. It is also CE  
marked for sale into the European Community for integration or use with medical products. It  
is certified by NEMKO according to EN60601-1 & EN60601-1-2 for sale to the medical market.  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 7  
UNPACKING  
Please check the following items are present when you unpack the box, and save the packing  
materials in case you will need to ship or transport the monitor in future.  
AMM17TK,AMM18TK,AMM19TK orAMM19TK/HB LCD Monitor and two video  
cable (1) VGA HDDB15 cable (1) DVI-D cable  
AUTO  
SELECT  
AC Power cord  
CAUTION  
Manufacturer :Ault Korea  
AC-Adapter  
Model No : MW160 or MW116  
Floppy Disk (for test pattern and set up)  
User Manual  
Composite Video (C-Video) Cable and Super Video (S-Video) Cable *Some Touchscreen  
Model Not Available  
8
User’s Guide  
Symbol Explanations  
This monitor is intended for use in Health Care Facilities.  
Regulatory Compliance  
This monitor has been tested to comply with IEC/EN 60601-1 and IEC/EN60601-1-2  
By NEMKO and is certified by UL to medical standard UL2601-1(UL/cUL Mark).  
Because many medical offices are located in residential areas, this monitor, in addition to the  
medical requirements, has also been tested and found to comply with the limits for FCC Class  
B computing devices in a typically configured system. It is the system integrator or  
configurer’s responsibility to test and ensure that the entire system complies with applicable  
EMC laws.  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 9  
EU Declaration of Conformity for Medical Applications  
ADeclaration of Conformity has been filed for this product.Asample of this  
document may be found in the addendum which accompanied this manual. For a  
copy of the Declaration of Conformity document, please contactADVAN Int’l  
Corp. and request forAMM17TK,AGMM18TK,AMM19TK and  
AMM19TK/HB DOC.  
Installation  
Before you unpack your monitor, prepare a suitable workspace. You need a stable  
and level surface near a grounded wall outlet in an area which is relatively free of  
glare from sunlight or other sources of bright light. The monitor is cooled by natural  
convection (it has no fan).  
For optimum performance, do not block the cooling vents.  
While unpacking the monitor, inspect it and other package contents for shipping  
damage that could cause a fire or shock hazard. Immediately report any shipping  
damage to the carrier or transportation company and contact customer service for  
monitor in the future or in case of return.  
After you unpack the monitor, make sure the following items are included  
• Monitor with 1.5 meter(5ft)monitor-to computer video cable  
• AC adapter with cable  
CAUTION: AC Adapter must be plugged into Grounded a power outlet)  
CAUTION : AC adapter  
Manufacturer: Ault korea  
Model No: MW160 or MW116  
Touchscreen cable if monitor has touchscreen option  
This operations manual  
Note: Your system provider may offer alternative cords or cables  
depending on the installation requirement and local geography issues.  
10 User’s Guide  
Equipment is not suitable for use in the presence of a flammable anesthetic mixture with air or  
with oxygen or nitrous oxide.  
No user serviceable parts inside, ask qualified personnel when accessing inside  
For disposal of waste product, you must follow the requirement of local code.  
Electrical input rating : 12V d.c. 6.67A  
Classification  
-
-
-
Type of protection against electric shock: Class I Equipment  
Degree of protection against the ingress of water: Ordinary  
Mode of operation: Continuous  
Environmental conditions for transport and storage:  
-
-
-
Temperature range within 20 oC to 60 oC  
Relative humidity range within 10% to 90%  
Atmospheric pressure range within 500 to 1060 hPa.  
SCREEN POSITION ADJUSTMENT  
In order to optimize the best viewing position, you can adjust the tilt of the monitor by using  
both of your hands to hold the edges of the monitor as shown in the figure below. The moni-  
tor can be adjusted to 28 degrees up as indicated by arrow below.  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 11  
SAFETY PRECAUTION  
Avoid placing the monitor, or any other heavy object, on the power cord to prevent fire or  
electrical shock from damage to the power cord.  
Do not expose the monitor to rain, excessive moisture, or dust to avoid fire or shock hazard.  
Do not cover the slots or openings of the monitor for proper heat dissipation. Always put  
the monitor in a place where there is adequate ventilation.  
Avoid placing the monitor against a bright background or where sunlight or other light  
sources may reflect on the area of the monitor. Place the monitor just below eye level.  
Handle with care when transporting the monitor.  
Refrain from giving the shock or scratch to the screen, as screen is fragile.  
CLEANING YOUR MONITOR  
No specific liquid or chemical necessary when cleaning this LCD monitor  
However, we suggest to clean the monitor with non-abrasive cloths and cleaning solutions  
used in hospitals to clean similar equipment. We recommend using 70% Isopropyl alcohol  
for the screen surface and warm water and a mild detergent for all other surfaces. Other  
acceptable cleaning agents are listed below:  
• 70% isopropyl alcohol  
• 6% aqueous ammonia  
• Cidex (2.4% glutaraldehyde solution)  
• Sodium Hypochlorite (bleach) 10%  
• “Green soap” USP  
• 0.5% Chlorhexidine in 70% isopropyl alcohol  
• Ovation  
• Formula 409  
• Fantastic  
Wex Cide  
To clean the screen, do not spray liquid cleaners directly on to the unit. Stand away Form the  
monitor and spray cleaning solution onto a cloth. Without applying excessive pressure,  
clean the screen with the slightly dampened rag.  
12 User’s Guide  
PRESET MODES  
To reduce the need for adjustment for different modes, the monitor has default setting modes  
that are most commonly used as given in the table below. If any of these display modes are  
detected, the monitor automatically adjusts the picture size and centering. When none of the  
mode is matched, the user can store their preferred modes in the user modes. The monitor is  
capable of storing up to 7 user modes. The only condition to store as a user mode is the new  
display information must have 1 KHz difference for horizontal frequency or 1 Hz for vertical  
frequency or the sync signal polarities are different from the default modes.  
M ode  
1
Resolution (H x V)  
640 x 350  
640 x 350  
640 x 400  
640 x 400  
720 x 350  
720 x 400  
720 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 960  
1280x1024  
1280x1024  
H. Freq. (KHz)  
31.5  
37.9  
31.5  
37.9  
31.5  
31.5  
37.9  
31.5  
37.9  
37.5  
43.3  
35.1  
37.9  
48.1  
46.9  
53.7  
35.5  
48.4  
56.5  
60  
V. Freq. (Hz)  
70  
85  
70  
85  
70  
70  
85  
60  
72  
75  
85  
56  
60  
72  
75  
85  
43  
60  
70  
75  
85  
75  
60  
60  
75  
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
68.7  
67.5  
60  
63.9  
79  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 13  
POWER MANAGEMENT FUNCTION  
The monitor is equipped with the power management function which automatically reduce the  
power consumption when not in use in three power level modes.  
Stand-by Mode  
The monitor goes into stand-by mode when the horizontal sync signal is off for about 10  
seconds. In this mode, the screen goes off and the power LED blinks for 3 seconds On  
and 1 second Off. The screen is displayed after the horizontal sync signal is restored.  
Suspend Mode  
The monitor goes into suspend mode when the vertical sync signal is off for about 10  
seconds. The power consumption during this is less than 8 W. In this mode, the screen  
goes off and the power LED blinks for 3 seconds On and 1 second Off. The screen is  
displayed after the vertical sync signal is restored.  
Off Mode  
The monitor goes into power-off mode when the vertical and horizontal sync signals are  
off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for  
3 seconds On and 1 second Off. The screen is displayed after the vertical and horizontal  
sync signals are restored.  
Power Management System  
TheAMM17TK,AMM18TK,AMM19TK andAMM19TK/HB Medical Monitor complies  
with the VESA DPMS power management proposal. The VESA DPMS proposal provides  
four phases of power-saving modes by detecting the horizontal sync signal as shown in the  
table blow.  
M ode  
D C Input Powe r  
(monitor only)  
A C Input powe r  
(Incl. A C adapte r)  
LED Status  
O n  
35 W max.  
4.5 W max.  
4.5 W max.  
4.5 W max.  
60 W max.  
6 W max.  
6 W max.  
6 W max.  
S teady G reen  
Blinking G reen  
Blinking G reen  
Blinking G reen  
S tandby  
S upend  
O n  
When the monitor is power saving mode or detects an incorrect timing, the screen will be  
blank and power LED indicator will blink.  
14 User’s Guide  
DDC  
To make your installation easier, the monitor is able to Plug and Play with your system if your  
system also supports DDC protocol. The DDC (Display Data Channel) is a communication  
protocol through which the monitor automatically informs the host system about its  
capabilities, for example, supported resolutions and corresponding timing. The monitor  
supports DDC1 and DDC2B standard.  
INSTALLATION  
To install the monitor to your host system, please follow the steps as given below:  
Steps  
1. Use the VGA cable that provides D-SUB 15-pin connector and connect to the  
15-pin connector on the VGA controller card.  
2. Connect the DC power to the DC power connector on the monitor.  
3. If use with USB hub, connect the loop cable between the monitor and the USB hub then  
connect the DC power to the bottom of USB hub.  
4. Connect one end of AC power cord into the AC Adapter and the other end to AC  
power outlet. (See page 13)  
5. Then turn the computer on and then the monitor.  
6. If the monitor still does not function properly, please refer to the troubleshooting section  
to diagnose the problem.  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 15  
Display for Video and Image Playback  
Explains how to use ourAMM17TK,AMM18TK,AMM19TK andAMM19TK/HB to playVCR,  
view television, video game, or digital camera images. It also show you how to connect video  
and other types of video equipment to the display.  
Connecting with Video Equipment  
You can connect many types of video equipment to the display. The equipment must have  
either Super video (S-video) ports or Composite video ports. To install the monitor to your  
video equipment, please follow the steps as given below:  
Steps  
1. Make sure the video equipment has a Super video (S-video) or a Composite video connector.  
2. Turn off the computer, display, and video equipment before any types of connection.  
3. For composite video, plug one end of an RCA cable into the video out port on the video  
equipment then connect the other end to the monitor video input port.  
4. For S-video, plug one end of the S-video cable into the video out port on the video equipment  
then connect the other end to the monitor S-video input port.  
5. Connect the DC power to the DC power connector on the monitor.  
6. Connect one end of AC power cord into the AC Adapter and the other end to AC  
power outlet.  
7. Then turn the video equipment on and then the monitor.  
Connecting to a Television Signal  
The display doesn’t have a tuner. To view television on the display, you need to use either the  
VCR or TV tuner card in your computer to change channels.  
Video and Sound  
This monitor does have speakers for sound. If you’re using the display to play a video or view  
television images, you need to connect the speakers to your television or video equipment  
for sound.  
16 User’s Guide  
USER CONTROLS  
Front Panel Controls  
1. Power LED:  
2. Power Switch:  
3. +:  
Lights up to indicate the power is turned ON.  
To turn ON or OFF the power.  
To increase the value of the parameter in the OSD you have selected for adjustment.  
To increase the brightness directly when OSD menu is not activated.  
To decrease the value of the parameter in the OSD you have selected for adjustment.  
To increase the brightness directly when OSD menu is not activated.  
To enter OSD menu then can use as moving upward in the OSD menu.  
To move downward in the OSD menu.  
4. -:  
5. Select Up:  
6. Select Down:  
Switch PC display to Video display and vice versa by one touch when OSD menu is not activated.  
One touch Auto adjust or Exit OSD menu.  
7. Auto Button:  
Standard OSD Operation  
1. Press menu button to activate the OSD.  
2. Use Select Up or Down keys to move up or down through the menu. The parameter will be highlighted wehn  
selected.  
3. Then use + or - to increase or decrease the value of the parameter, or make selection between different options.  
4. To quit the OSD screen at any time during the operation, pressAuto button. If no keys are pressed for a time period,  
the OSD automatically disappears.  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 17  
OSD Scren Basic Section (VGA)  
For OSD display, push “Menu”. For selecting Icon, push “Up”  
or “Down”  
Push “Up” or “Down” button to select between Push “Up” or “Down” button to select between  
“Brightness” or “Contrast” then push “Select”  
Use “Left” or “Right” button to adjust  
“Frequency” or “Phase” then push “Select”  
Use “Left” or “Right” button to adjust  
Push “Up” or “Down” button to select between “OSD  
Hor. Pos.”, “OSD Ver. Pos.”, “OSD Background”, or  
“User Timeout” then push “Select”  
Push “Up” or “Down” button to select between  
“Horizontal” or “Vertical” then push “Select”  
Use “Left” or “Right” button to adjust  
Use “Left” or “Right” button to adjust  
Push “Left” or “Right” to select Color Temp betweenPush “Up” or “Down” button to select between  
“5000”, “6500”, 7300”, “9500”, or “User” then push  
“Select”  
“DPMS”, “Auto Source Select”, or “Freeze Frame”  
then push “Select” Use “Left” or “Right” button to  
If “User” were slected, push “Up” or “Down” button to adjust  
select between “Red”, “Green”, or “Blue” then push  
“Select”  
Use “Left” or “Right” button to adjust  
18 User’s Guide  
OSD Scren Basic Section (VGA)  
For OSD display, push “Menu”. For selecting Icon, push “Up”  
or “Down”  
Push the select button  
Use “Left” or “Right” button to adjust  
Push the select button to execute the Zoom  
function  
Push “Up” or “Down” button to select between  
“Analog RGB”, “Digital RGB”, “Composite Video” or  
“Super Video”  
Use “Left” or “Right” to choose the correct mode then  
push “Select” button  
Push the select button  
Use “Left” or “Right” button to adjust  
Push the select button to execute the Auto  
Setup function or Push the select button to  
execute Recall Factory Default  
Push the select button to execute Information  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 19  
OSD Scren Basic Section (DVI)  
For OSD display, push “Menu”. For selecting Icon, push “Up”  
or “Down”  
Push “Up” or “Down” button to select between “OSD  
Hor. Pos.”, “OSD Ver. Pos.”, “OSD Background”, or  
“User Timeout” then push “Select”  
Push “Up” or “Down” button to select between  
“Brightness” or “Contrast” then push “Select”  
Use “Left” or “Right” button to adjust  
Use “Left” or “Right” button to adjust  
Push “Left” or “Right” to select Color Temp betweenPush “Up” or “Down” button to select between  
“5000”, “6500”, 7300”, “9500”, or “User” then push  
“Select”  
“DPMS”, “Auto Source Select”, or “Freeze Frame”  
then push “Select” Use “Left” or “Right” button to  
If “User” were slected, push “Up” or “Down” button to adjust  
select between “Red”, “Green”, or “Blue” then push  
“Select”  
Use “Left” or “Right” button to adjust  
Push the select button  
Use “Left” or “Right” button to adjust  
Push the select button to execute the Zoom  
function  
20 User’s Guide  
OSD Scren Basic Section (DVI)  
For OSD display, push “Menu”. For selecting Icon, push “Up”  
or “Down”  
Push “Up” or “Down” button to select between  
“Analog RGB”, “Digital RGB”, “Composite Video” or  
“Super Video”  
Use “Left” or “Right” to choose the correct mode then  
Push the select button  
Use “Left” or “Right” button to adjust  
push “Select” button  
Push the select button to execute Recall  
Factory Default  
Push the select button to execute Information  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 21  
OSD Scren Basic Section (C-Video or S-Video)  
For OSD display, push “Menu”. For selecting Icon, push “Up”  
or “Down”  
Push “Up” or “Down” button to select between  
“Brightness” or “Contrast” then push “Select”  
Use “Left” or “Right” button to adjust  
Push “Select” button then “Up” or “Down”  
Push “Left” or “Right” button to adjust  
Push “Up” or “Down” button to select between “OSD  
Hor. Pos.”, “OSD Ver. Pos.”, “OSD Background”, or  
“User Timeout” then push “Select”  
Push “Up” or “Down” button to select between  
“Horizontal” or “Vertical” then push “Select”  
Use “Left” or “Right” button to adjust  
Use “Left” or “Right” button to adjust  
Push “Left” or “Right” to select Color Temp  
Push “Up” or “Down” button to select between  
between “5000”, “6500”, 7300”, “9500”, or “User” “DPMS”, “Auto Source Select”, “Freeze Frame”, or  
then push “Select” “ADC Calibration” then push “Select”  
If “User” were slected, push “Up” or “Down” button Use “Left” or “Right” button to adjust  
to select between “Red”, “Green”, or “Blue” then  
push “Select”  
Use “Left” or “Right” button to adjust  
22 User’s Guide  
OSD Scren Basic Section (C-Video or S-Video)  
For OSD display, push “Menu”. For selecting Icon, push “Up”  
or “Down”  
Push the select button  
Push the select button  
Use “Left” or “Right” button to adjust  
Use “Left” or “Right” button to adjust  
Push the select button  
Use “Left” or “Right” button to adjust  
Push the select button to execute Recall  
Factory Default  
Push the select button to execute Information  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 23  
OSD Function Description (Under Analog Display)  
Item  
Function Description  
Brightness  
Contrast  
To increase or decrease the brightness.  
To increase or decrease the contrast.  
To adjust frequency (dot clock).  
To adjust phase (clock-phase).  
Frequency  
Phase  
Horizontal  
Vertical  
To move the screen left or right.  
To move the screen upward or downward.  
To move OSD menu left or right.  
To move OSD menu upward or downward.  
OSD Hor Pos  
OSD Ver Pos  
OSD Background Choose between Opaque or Translucent.  
User Timeout  
Color Temp  
Set OSD screen appearing time.  
Choose between 5000, 6500, 7300, 9500, or User for color  
temp.  
Red  
Balance Red.  
Green  
Blue  
Balance Green.  
Balance Blue.  
DPMS  
Enable or Disable DPMS.  
Adjust auto source select between off, low, or hight.  
Auto Source  
Select  
Freeze Frame  
Zoom  
Enable or Disable freeze frame  
Enable zoom-in function  
Image Sharpness  
Scale Mode  
Set image sharpness from 1 to 5.  
Choose scale mode between fill screen, aspect ratio, or one  
to one  
Input Source  
Select  
Choose input source between analog RGB, digital RGB,  
composite video, or super video  
Auto Adjust  
The Auto-Adjust will automatically adjust V-Position, H-  
Position, Clock,  
Clock-Phase, and Contrast, the whole process takes about 5  
seconds. (Please use the test pattern file in the attached LCD  
monitor utility disk for Auto Adjust).  
Recall Factory  
Default  
Set to factory default.  
Infomation  
Display information on resolution, refresh rate, and input  
mode.  
24 User’s Guide  
OSD Function Description (Under Digital Display)  
Ite m  
Function D e scription  
Brightness  
To increase or decrease the brightness.  
To increase or decrease the contrast.  
To move the screen left or right.  
Contrast  
Horizontal  
Vertical  
To move the screen upward or downward.  
To move O SD menu left or right.  
To move O SD menu upward or downward.  
Choose between Opaque or Translucent.  
Set OSD screen appearing time.  
OSD Hor Pos  
OSD Ver Pos  
OSD Background  
User Timeout  
Color Temp  
Choose between 5000, 6500, 7300, 9500, or User for color  
temp.  
Red  
Balance Red.  
Green  
Blue  
Balance Green.  
Balance Blue.  
DPMS  
Enable or Disable DPMS.  
Adjust auto source select between off, low, or hight.  
Auto Source  
Select  
Freeze Frame  
Zoom  
Enable or Disable freeze frame  
Enable zoom-in function  
Image Sharpness  
Scale Mode  
Set image sharpness from 1 to 5.  
C hoose scale mode between fill screen, aspect ratio, or one  
to one  
Input Source  
Select  
Choose input source between analog RGB, digital RGB,  
composite video, or super video  
Recall Factory  
Default  
Set to factory default.  
Infomation  
Display information on resolution, refresh rate, and input  
mode.  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 25  
OSD Function Description (Under C-Video or S-Video Display)  
Ite m  
Function D e s cription  
Hue  
To increase or decrease the hue level.  
To increase or decrease the saturation level.  
To increase or decrease the brightness.  
To increase or decrease the contrast.  
To move the screen left or right.  
Saturation  
Brightness  
C ontrast  
Horizontal  
Vertical  
To move the screen upward or downward.  
To move O SD menu left or right.  
O SD Hor Pos  
O SD Ver Pos  
O SD Background  
User Timeout  
C olor Temp  
To move O SD menu upward or downward.  
C hoose between O paque or Translucent.  
Set O SD screen appearing time.  
C hoose between 5000, 6500, 7300, 9500, or User for color  
temp.  
Red  
Balance Red.  
Green  
Blue  
Balance Green.  
Balance Blue.  
DPM S  
Enable or Disable DPM S.  
Adjust auto source select between off, low, or hight.  
Auto Source  
Select  
Freeze Frame  
Zoom  
Enable or Disable freeze frame.  
Enable zoom- in function.  
Image Sharpness  
Set image sharpness from 1 to 5.  
Video Scale Mode C hoose video scale mode between normal, 4:3 scale mode,  
or 16:9 scale mode.  
Video Sharpness  
To increase or decrease the video sharpness.  
Input Source  
Select  
C hoose input source between analog RGB, digital RGB,  
composite video, or super video  
Recall Factory  
Default  
Set to factory default.  
Infomation  
Display information on resolution, refresh rate, and input  
mode.  
26 User’s Guide  
TROUBLESHOOTING  
Before sending your LCD monitor for servicing, please check the troubleshooting list below  
to see if you can self-diagnose the problem.  
Problems Current Status  
LED ON  
Remedy  
Using OSD, adjust brightness and contrast to  
maximum or reset to their default settings.  
LED OFF  
Check the power switch.  
No  
Picture  
Check if AC power cord is properly  
connected to the AC adapter.  
LED Blinking  
Check if video signal cable is properly  
connected at the back of monitor.  
Check if the power to computer system is ON.  
Unstable Picture  
Check if the specification of graphics adapter  
and monitor is in compliance which may be  
causing the input signal frequency mismatch.  
Display is  
Using Auto Setup button, if still display  
abnormal picture then adjust CLOCK,  
CLOCK-PHASE, H-POSITION and V-  
POSITION with non-standard signals.  
missing, center  
shift, or too small  
or too large in  
Abnormal  
Picture  
display size  
Using OSD, in case of missing full-screen  
image, please select other resolution in your  
Operating System (Windows 95/98, NT) or  
other vertical refresh timing.  
Must wait for a few seconds after adjusting  
the size of the image before changing or  
disconnecting the signal or powering OFF the  
monitor.  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 27  
SPECIFICATION  
AMM170TK  
LCD Panel  
Type  
43.2cm/17-inch Color TFT Panel  
Active Matrix  
Resolution  
1280 dots x 1024 lines (Recommended)  
0.264mm  
Pixel Pitch  
Display Color  
Response Time  
Color Tone  
Color Filter  
Face Finishing  
Viewing Angle  
Video  
16 million colors  
25ms  
Up to 256 tone  
RGB vertical stripe type  
Anti-Glare Hard Coated  
170°H 170°V (CR>=10)  
0.7Vp-p analog RGB & TMDS (PanelLink) Digital  
165 MHz x 1  
Input Signal  
Sync  
2.5~5.0Vp-p separated sync  
Input Impedance (Analog)  
Video - 75 Ohm  
Sync - 1k Ohm  
Composite Sync  
Digital  
C-Video, S-Video  
3 channel TMDS receiver, single pixel 24 bit MSB-  
aligned RGB TFT  
Scanning Frequency  
Horizontal  
30~68kHz  
Vertical  
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to  
75Hz at 1280 x 1024)  
Display Size  
H x V  
13.3" x 10.6" (337.92mm x 270.33mm)  
Brightness, Contrast Radtio, Gray Scales  
Brightness  
250 cd/m2, Standard  
500:1 Typ.  
Contrast Ratio  
Gray Scales  
Up to 256 steps  
Signal Input Connector  
Video  
HD15-15pin, Digital DVI, NTSC, S-Video  
RS-232 DB-9 (Optional)  
Touchscreen  
Temperature Environment  
Operating Temperature  
Storage Temperature  
Humidity  
32° ~ 122°F (0° - 50°C)  
-4° ~ 149°F (-20° - 65°C)  
10 ~ 90%RH (without condensation)  
Power Source  
Display Monitor  
AC-Adapter  
DC 12V  
AC100~240V 60W (Without option, Normal  
Operation)  
Regulations  
Safety and EMC  
UL/cUL, FCC, CE, TCO99, Energy Star, CB, MPR  
II, ERG/GS.VCCI, UL2601-1, EN60601-1  
Cabinet  
Desktop Stand  
17.5inch (W) x 17.8inch (H) x 9.5inch (D)  
450mm (W) x 455mm (H) x 245mm (D)  
Free Mount  
17.5inch (W) x 14.25inch (H) x 3inch (D)  
450mm (W) x 362mm (H) x 76mm (D)  
Weight  
Desktop Stand  
Free Mount  
Tilt Base  
20.6 lb. (9.3Kg)  
16 lb. (7.3Kg)  
0° Down 28° Up  
Touch Panel  
Optional Module  
* All contents are subject to change without notice.  
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.  
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE  
28 User’s Guide  
SPECIFICATION  
AMM17TK  
LCD Panel  
Type  
44.2cm/17.4-inch Color TFT Panel  
Active Matrix  
Resolution  
Pixel Pitch  
Display Color  
Response Time  
Color Tone  
Color Filter  
Face Finishing  
Viewing Angle  
Video  
1280 dots x 1024 lines (Recommended)  
0.27mm  
16 million colors  
25ms  
Up to 256 tone  
RGB vertical stripe type  
Anti-Glare Hard Coated  
160°H 160°V (CR>=10)  
0.7Vp-p analog RGB & TMDS (PanelLink) Digital  
165 MHz x 1  
Input Signal  
Sync  
2.5~5.0Vp-p separated sync  
Input Impedance (Analog)  
Video - 75 Ohm  
Sync - 1k Ohm  
Composite Sync  
Digital  
C-Video, S-Video  
3 channel TMDS receiver, single pixel 24 bit MSB-  
aligned RGB TFT  
Scanning Frequency  
Horizontal  
30~68kHz  
Vertical  
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to  
75Hz at 1280 x 1024)  
Display Size  
H x V  
13.6" x 10.9" (345.0mm x 276.48mm)  
Brightness, Contrast Radtio, Gray Scales  
Brightness  
220 cd/m2, Standard  
400:1 Typ.  
Contrast Ratio  
Gray Scales  
Up to 256 steps  
Signal Input Connector  
Video  
HD15-15pin, Digital DVI, NTSC, S-Video  
RS-232 DB-9 (Optional)  
Touchscreen  
Temperature Environment  
Operating Temperature  
Storage Temperature  
Humidity  
32° ~ 104°F (0° - 35°C)  
-4° ~ 140°F (-20° - 60°C)  
10 ~ 90%RH (without condensation)  
Power Source  
Display Monitor  
AC-Adapter  
DC 12V  
AC100~240V 60W (Without option, Normal  
Operation)  
Regulations  
Safety and EMC  
UL/cUL, FCC, CE, TCO99, Energy Star, CB, MPR  
II, ERG/GS.VCCI, UL2601-1, EN60601-1  
Cabinet  
Desktop Stand  
17.5inch (W) x 17.8inch (H) x 9.5inch (D)  
450mm (W) x 455mm (H) x 245mm (D)  
Free Mount  
17.5inch (W) x 14.25inch (H) x 3inch (D)  
450mm (W) x 362mm (H) x 76mm (D)  
Weight  
Desktop Stand  
Free Mount  
Tilt Base  
20.6 lb. (9.3Kg)  
16 lb. (7.3Kg)  
0° Down 28° Up  
Touch Panel  
Optional Module  
* All contents are subject to change without notice.  
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.  
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 29  
SPECIFICATION  
AMM18TK  
LCD Panel  
Type  
46cm/18.1-inch Color TFT Pane  
Active Matrix  
Resolution  
Pixel Pitch  
Display Color  
Response Time  
Color Tone  
Color Filter  
Face Finishing  
Viewing Angle  
Video  
1280 dots x 1024 lines (Recommended)  
0.28mm  
16 million colors  
40ms  
Up to 256 tone  
RGB vertical stripe type  
Anti-Glare Hard Coated  
160°H 160°V (CR>=10)  
0.7Vp-p analog RGB & TMDS (PanelLink) Digital  
165 MHz x 1  
Input Signal  
Sync  
2.5~5.0Vp-p separated sync  
Input Impedance (Analog)  
Video - 75 Ohm  
Sync - 1k Ohm  
Composite Sync  
Digital  
C-Video, S-Video  
3 channel TMDS receiver, single pixel 24 bit MSB-  
aligned RGB TFT  
Scanning Frequency  
Horizontal  
30~68kHz  
Vertical  
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to  
75Hz at 1280 x 1024)  
Display Size  
H x V  
14.13" x 11.3" (359mm x 287mm)  
Brightness, Contrast Radtio, Gray Scales  
Brightness  
200 cd/m2, Standard  
250:1 Typ.  
Contrast Ratio  
Gray Scales  
Up to 256 steps  
Signal Input Connector  
Video  
DB9-15pin, Digital DVI, NTSC, S-Video  
RS-232 DB-9 (Optional)  
Touchscreen  
Temperature Environment  
Operating Temperature  
Storage Temperature  
Humidity  
41° ~ 95°F (5° - 35°C)  
-4° ~ 140°F (-20° - 60°C)  
10 ~ 90%RH (without condensation)  
Power Source  
Display Monitor  
AC-Adapter  
DC 12V  
AC100~240V 60W (Max.)  
Regulations  
Safety and EMC  
UL/cUL, FCC, CE, TCO99, Energy Star, CB, MPR  
II, ERG/GS.VCCI, UL2601-1, EN60601-1  
Cabinet  
Desktop Stand  
Free Mount  
Weight  
17.5inch (W) x 17.8inch (H) x 9.5inch (D)  
17.5inch (W) x 14.25inch (H) x 3inch (D)  
Desktop Stand  
Free Mount  
Tilt Base  
22.8 lb. (10.4Kg)  
18.1 lb. (8.2Kg)  
0° Down 28° Up  
Touch Panel  
Optional Module  
* All contents are subject to change without notice.  
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.  
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE  
30 User’s Guide  
SPECIFICATION  
AMM19TK  
LCD Panel  
Type  
48cm/19-inch Color TFT Pane  
Active Matrix  
Resolution  
Pixel Pitch  
Display Color  
Response Time  
Color Tone  
Color Filter  
Face Finishing  
Viewing Angle  
Video  
1280 dots x 1024 lines (Recommended)  
0.294mm  
16 million colors  
25ms  
Up to 256 tone  
RGB vertical stripe type  
Anti-Glare Hard Coated  
170°H 170°V (CR>=10)  
0.7Vp-p analog RGB & TMDS (PanelLink) Digital  
165 MHz x 1  
Input Signal  
Sync  
2.5~5.0Vp-p separated sync  
Input Impedance (Analog)  
Video - 75 Ohm  
Sync - 1k Ohm  
Composite Sync  
Digital  
C-Video, S-Video  
3 channel TMDS receiver, single pixel 24 bit MSB-  
aligned RGB TFT  
Scanning Frequency  
Horizontal  
30~68kHz  
Vertical  
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to  
75Hz at 1280 x 1024)  
Display Size  
H x V  
14.8" x 11.9" (376mm x 301mm)  
Brightness, Contrast Radtio, Gray Scales  
Brightness  
250 cd/m2, Standard  
500:1 Typ.  
Contrast Ratio  
Gray Scales  
Up to 256 steps  
Signal Input Connector  
Video  
HD15-15pin, Digital DVI, NTSC, S-Video  
RS-232 DB-9 (Optional)  
Touchscreen  
Temperature Environment  
Operating Temperature  
Storage Temperature  
Humidity  
32° ~ 122°F (0° - 50°C)  
-4° ~ 140°F (-20° - 60°C)  
10 ~ 90%RH (without condensation)  
Power Source  
Display Monitor  
AC-Adapter  
DC 12V  
AC100~240V 80W (Max.)  
Regulations  
Safety and EMC  
UL/cUL, FCC, CE, Energy Star, CB, MPR II,  
ERG/GS.VCCI, UL2601-1, EN60601-1  
Cabinet  
Desktop Stand  
Free Mount  
Weight  
17.5inch (W) x 17.8inch (H) x 9.5inch (D)  
17.5inch (W) x 14.25inch (H) x 3inch (D)  
Desktop Stand  
Free Mount  
Tilt Base  
19 lb. (8.6Kg)  
16 lb. (7.3Kg)  
0° Down 28° Up  
Touch Panel  
Optional Module  
* All contents are subject to change without notice.  
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.  
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 31  
SPECIFICATION  
AMM19TK/HB  
LCD Panel  
Type  
48cm/19-inch Color TFT Pane  
Active Matrix  
Resolution  
1280 dots x 1024 lines (Recommended)  
0.294mm  
Pixel Pitch  
Display Color  
Response Time  
Color Tone  
Color Filter  
Face Finishing  
Viewing Angle  
Video  
16 million colors  
25ms  
Up to 256 tone  
RGB vertical stripe type  
Anti-Glare Hard Coated  
170°H 170°V (CR>=10)  
0.7Vp-p analog RGB & TMDS (PanelLink) Digital  
165 MHz x 1  
Input Signal  
Sync  
2.5~5.0Vp-p separated sync  
Input Impedance (Analog)  
Video - 75 Ohm  
Sync - 1k Ohm  
Composite Sync  
Digital  
C-Video, S-Video  
3 channel TMDS receiver, single pixel 24 bit MSB-  
aligned RGB TFT  
Scanning Frequency  
Horizontal  
30~68kHz  
Vertical  
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to  
75Hz at 1280 x 1024)  
Display Size  
H x V  
14.8" x 11.9" (376mm x 301mm)  
Brightness, Contrast Radtio, Gray Scales  
Brightness  
450 cd/m2, Standard  
600:1 Typ.  
Contrast Ratio  
Gray Scales  
Up to 256 steps  
Signal Input Connector  
Video  
HD15-15pin, Digital DVI, NTSC, S-Video  
RS-232 DB-9 (Optional)  
Touchscreen  
Temperature Environment  
Operating Temperature  
Storage Temperature  
Humidity  
32° ~ 122°F (0° - 50°C)  
-4° ~ 140°F (-20° - 60°C)  
10 ~ 90%RH (without condensation)  
Power Source  
Display Monitor  
AC-Adapter  
DC 12V  
AC100~240V 80W (Max.)  
Regulations  
Safety and EMC  
UL/cUL, FCC, CE, Energy Star, CB, MPR II,  
ERG/GS.VCCI, UL2601-1, EN60601-1  
Cabinet  
Desktop Stand  
Free Mount  
Weight  
17.5inch (W) x 17.8inch (H) x 9.5inch (D)  
17.5inch (W) x 14.25inch (H) x 3inch (D)  
Desktop Stand  
Free Mount  
Tilt Base  
19 lb. (8.6Kg)  
16 lb. (7.3Kg)  
0° Down 28° Up  
Touch Panel  
Optional Module  
* All contents are subject to change without notice.  
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.  
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE  
32 User’s Guide  
Connectors  
DC Input  
Connector Jack Power Input  
The SCD-014-1-A (SHIUA CHYUAN) or equivalent.  
Pin Description  
1 +12V DC  
2 GND  
VideoInput  
15 pin D-subminiature connector.  
The vedor P/N is DHSB-15 FRF7(LEOCO) or equivalent.  
D
e s c r i p t io n  
P in  
D
e s c r i p t io n  
P in  
9
R e d V id e o  
G r e e n V id e o  
B lu e V id e o  
1
N
C
2
3
4
5
6
7
8
V G A  
C
o n  
1 0  
1 1  
1 2  
1 3  
1 4  
1 5  
N
C
N
C
S D A ( D D C 1 /2 )  
H - s y n c  
L o g ic G r o u n d  
R e d V id e o G r o u n d  
G r e e n V id e o G r o u n d  
B lu e V id e o G r o u n d  
V - s y n c  
S C  
L
( D D C 2 B )  
24 pin DVI-D connector.  
DDWG or equivalent connector.  
P in  
S ig na l A s s ig nm e nt  
T.M .D .S . D a ta 2 -  
T.M .D .S . D a ta 2 +  
P in  
9
S ig na l A s s ig nm e nt  
T.M .D .S . D ata 1 -  
T.M .D .S . D ata 1 +  
P in  
1 7  
S ig na l A s s ig nm e nt  
T.M .D .S . D ata0 -  
T.M .D .S . D ata0 +  
1
2
3
1 0  
11  
1 8  
T.M .D .S . D a ta 2 /4  
S hield  
T.M .D .S . D ata 1 /3  
S hield  
1 9  
T.M .D .S . D ata0 /5  
S hie ld  
4
5
6
T.M .D .S . D a ta 4 -  
T.M .D .S . D a ta 4 +  
D D C C lo c k  
1 2  
1 3  
1 4  
T.M .D .S . D ata 3 -  
T.M .D .S . D ata 3 +  
+ 5 V P o w e r  
2 0  
2 2  
2 2  
T.M .D .S . D ata5 -  
T.M .D .S . D ata5 +  
T.M .D .S . C lo ck  
S hie ld  
7
8
D D C D a ta  
1 5  
1 6  
G ro und (fo r + 5 V )  
H o t P lug D etec t  
2 3  
2 4  
T.M .D .S . C lo ck +  
T.M .D .S . C lo ck -  
N o C o nnec t  
Touch Port  
9Pin D-subminiature connector.  
D
D
R
T
e
C
X
X
T
s
c
r i p t i o  
n
P
1
i n  
D
D
R
C
R
e
s
c
r i p t i o  
n
P
i n  
D
S
R
6
D
D
R
2
T
S
7
3
T
S
8
D
4
I N  
C
9
L
o
g
i c  
5
G
r o  
u
n
d
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 33  
Description of Warranty  
Advan warrants that the goods the goods sold hereunder will be free of defects in materials  
and workmanship, and such goods will substantially conform to the specifications furnished  
by Advan, and to any drawings or specifications furnished to Advan by the Buyer if  
approved by Advan. This warranty shall be effective only if Advan receives notice of such  
defect or nonconformance during the period of the warranty. Advan sole and exclusive the  
Advan product(s) with refurbished units provide a credit to buyer in the amount of the  
purchase  
price.  
Commencement and Duration of Warranty  
The warranty period begins on the date of shipment from Advan. The goods sold hereunder  
are warranted for a period of three years (36 months) from date of shipment unless otherwise  
agreed to by Buyer and Advan. No extension of the warranty will be given during the time  
the goods are in Advan possession.  
Place of Repair or Replacement  
In order to obtain service under this warranty, Buyer must notify Advan of the defect before  
expiration on the warranty period, and request a “Return MaterialAuthorization Number.” If  
the configuration has been modified in any manner, the product must be returned to its  
original configuration before any warranty service will be perfomed by Advan. No goods are  
to be returned to Advan without prior authorization. Buyer will be responsible for packaging  
and shipping the defective goods to the Advan Service Facility with shipping charges  
prepaid.  
Limitation of Warranty  
Monitor:  
For one years (12 months) after the date of purchase,ADVAN or itsAuthorized Service Centers,  
will repair or replace if defective in material or workmanship. This Limited Warranty does not  
include cleaning, or damage caused by accident, neglect, misuse or improper installation or  
operation, any damage caused from service, maintenance, modifications or tampering by anyone  
other than anADVANAuthorized Service Representative, or by the use of supplies, consumable  
items and conditions beyond the control ofADVAN, such as common carrier provided equipment  
and/or facilities, operation ofADVAN product in excess of the specifications or with the Serial  
Number or Rating label removed.  
*Touch Screen:  
For one year after the date of purchase, ADVAN or itsAuthorized Service Centers, will repair  
or replace if defective in material or workmanship. This Limited Warranty does not include  
cleaning, or damage caused by accident, neglect, misuse or improper installation or opera-  
tion, any damage caused from service, maintenance, modifications or tampering by anyone  
other than an ADVAN Authorized Service Representative, or by the use of supplies, consum-  
able items and conditions beyond the control of ADVAN, such as common carrier provided  
equipment and/or facilities, operation of ADVAN product in excess of the specifications or  
with the Serial Number or Rating label removed.  
34 User’s Guide  
ADVAN DISCLAIMSALLOTHERWARRANTIES EXPRESS OR IMPLIED INCLUDING,  
WITHOUT LIMITATION,ANYIMPLIED WARRANTIES OF MERCHANTABILITYOR  
FITNESS FOR PARTICULAR PURPOSE, EXCEPTTO THE EXTENTTHATANYWARRAN-  
TIES IMPLIED BYLAWCANNOTBEVALIDLYWAIVED.  
No oral or written information or advice given byADVAN, its authorized service center,  
distributors, dealers, agents or employees, shall create another warranty or modify this  
warranty. This warranty states ADVAN’s entire liability and your exclusive remedy against  
ADVAN for any failure of theADVAN’s product to operate properly.  
Neither ADVAN nor anyone else involved in the development, production, or delivery of this  
product shall be liable for any indirect, incidental, special consequential, exemplary, or  
punitive damages, including lost profits, arising from the use of or inability to consequential  
or incidental damages, the above limitation may not apply to you.  
This Limited Warranty gives you special legal rights and you may also have other right,  
which vary from State to State.  
Installation  
Advan makes no warranty with respect to any installation of Advan’s product(s)  
by Advan, any authorized dealer, or any other person.  
Technical Assistance  
For technical assistance please call (510)490-1005 between 8:00 a.m. and 5:00 p.m. PST,  
Monday through Friday or email to [email protected] with a description of your  
technical issues.  
Service  
If your Medical Monitor needs service, call Advan Customer Service at  
(510)490-1005 between 7:00 a.m and 4:00 p.m PST, Monday through  
Friday or fax to (510)490-1151. You will need the unit’s serial number and a  
brief description of the problem and where unit were purchased to receive a RMA number.  
If a service is required please return the product for service using the original shipping  
container with the RMA number included in package on the outside of the box.  
In order to protectADVAN employees form potential health hazards,ADVAN requires that  
the RMAproduct be disinfected before returning toADVAN forservice.Any product not  
cleaned prior to shipment will be returned to the customer.  
Note: Returns will not be accepted without an assigned RMA number.  
In-transit damage is not covered by warranty. We suggest you always insure your shipment.  
Advan will only pay for the return shipment by surface transportation. It is the responsibility  
of the sender to prepay transportation charges.  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 35  
Tounchscreen User's Manual (AMM17TK-TE/AMM18TK-TE/  
AMM19TE orAMM17TK-TEW/AMM18TK-TEW/AMM19TK-TEW)  
Quick Start  
1.Connect Power Code and VGACable of LCD Monitor.  
2.Connect Touchscreen DB9 male RS-232 cable.  
3.Turn the LCD display Power ON.  
4.Adjust the tilt of LCD Monitor.  
5.Adjust the Picture of LCD Monitor.  
6.Install driver software of Touchscreen (See "Driver software" for details).  
7.Adjust the calibration of Touchscreen (See "Driver software" for details).  
Introduction  
The ELO IntelliTouch Touchscreen system consists of a touchscreen and an  
electronic touchscreen controller. The touchscreen may be a flat, spherical, or  
cylindrical and is installed over the face of the LCD. The touchscreen controller  
installed inside of theLCD.  
The IntelliTouch Touchscreen  
The IntelliTouch surface wave touchscreen consists of a glass panel molded to the  
precise shape of a display's face.Ascratch-resistant, hard-coated plastic cover  
sheet may be clear for best image clarity or have an antiglare finish.  
The IntelliTouch Controller  
The IntelliTouch controllers provide the drive signal for touchscreen, convert the  
received analogue signals into digital touch coordinates, and send these  
coordinates to the computer.  
36 User’s Guide  
Touchmonitorinstallation  
Cable Connection  
1. Connect and test LCD as a video display only.  
2. Plug the DB9 male into the DB9 female connector labled "TOUCHSCREEN"  
on the back of the LCD Monitor.  
Driver software  
ELO provide driver programs for the DOS, Windows 3.1, Windows 95/98,  
Windows NT, Windows 2000, Windows XP, OS/2, and Macintosh systems.  
Additional drivers may be available for other system. Contact ELO for details.  
Installing Driver software forWindows /Windows NT  
1. Shutdown Windows or Windows NT and turn off your computer.  
2. Install touchscreen hardware as described in the "Quick start" or "Touchmonitor  
installation".  
3. Start your computer.  
4. Insert the Windows or Windows NT driver disk into diverAor B.  
5. Browse for "setup.exe" in the directory to which you extracted the driver files.  
6. Type "setup.exe" in the space provided and press Enter.  
7. The touchscreen setup wizard will appear. You will need to select serial port,  
type of touchscreen controller, and language.  
8. Complete the setup program.  
9. Shutdown and restart windows NT.  
10. Click the start button, then click control panel.  
11. Double-click touchscreen control panel.  
12. Click the calibrate button and touch each of the three targets as they appear  
on the screen.  
Contacting ELO  
ELO Touchsystems INC.  
6500 Kaiser Drive Fremont,  
CA 94554 USA  
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 37  

Hotpoint E6004 User Manual
Hobart CG831 User Manual
GE 27958 User Manual
Epson S1C6200A User Manual
Dell Computer Monitor ST2420L User Manual
DCS SW 6000 User Manual
Asus P4SGX MX User Manual
Asus DELUXE P8Z77 V User Manual
AMX Modero NXD 500i User Manual
AMC i T15 User Manual