Electrolux CSIG 316 User Manual

CSIG 316  
Owners handbook  
and  
Installation instructions  
C S I G 3 1 6  
Contents  
Page  
Lighting the cooker  
4
The grill  
7
10  
13  
15  
18  
20  
24  
26  
28  
29  
31  
32  
33  
34  
35  
36  
The hotplate  
The oven  
Oven cooking chart  
Slow cooking  
Care and cleaning  
Installing the cooker  
General information  
What is wrong and why?  
Servicing  
Installation Instructions  
Technical data  
Safety requirements/ventilation  
Location of appliance  
Installation  
Testing  
3
C S I G 3 1 6  
Lighting the cooker  
The ignition system works by means of a battery. Details on how to  
replace the battery are given on page 26.  
Hotplate  
To light  
Push in the control knob and turn to the large flame symbol (highest  
setting), and press the ignition button immediately. When the burner has  
lit release the button.  
Warning: If the ignition button is not pressed immediately a build up of  
gas may cause the flame to spread.  
4
C S I G 3 1 6  
Grill  
To light:  
1 Push in the control knob and turn it to the large flame symbol  
(highest setting), and press the ignition button immediately. When  
the burner has lit release the button.  
Warning: If the ignition button is not pressed immediately a build up of  
gas may cause the flame to spread from the grill cavity.  
For your safety  
Never cover the grill pan or grid with foil as this can lead to  
grill fires  
Oven  
To light:  
1 Open the oven door.  
2 Push in the control knob and turn it to gas mark 9, and press the  
ignition button immediately. When the burner has lit release the  
button. There will only be small flames at first.  
3 Now turn the control knob to the  
gas mark you want.  
4 Wait until the burner is showing  
large flames.  
5 Close the oven door.  
5
C S I G 3 1 6  
To turn off any burner  
1 Push in the control knob and turn it to the off position. This is shown  
by a large dot.  
For your safety  
When you are lighting any burner check that it has lit before  
you leave the cooker.  
When you are turning off a burner, do not leave the cooker  
until the flame has gone out.  
6
C S I G 3 1 6  
The grill  
The grill is a high-speed grill. The instructions below tell you how to vary  
the heat setting and how to change the height of the grid to suit the food  
you are cooking. You should remember to turn the food regularly.  
You should not use the grill to keep food warm as it will continue to  
cook the food.  
For your safety  
You must keep the grill door open when the grill burner is lit.  
Caution  
Accessible parts may be hot when the grill is used. Young  
children should be kept away.  
Never cover the grill pan or grid with foil as this can lead to grill  
fires.  
Heat control  
The grill control has two heat  
settings.  
The control knob turns to the left  
from 'OFF' to 'HIGH' and then to  
'LOW'. Use the high setting for fast  
cooking such as toast. Use the low  
setting to cook thicker food such as  
chicken after you have browned it  
on the high setting.  
Cooking positions  
You can put the grill shelf in either  
of the two positions.  
Most food should be cooked on  
the grid in the grill pan. You can turn  
the grid over to suit different  
thicknesses of food.  
You can place some dishes  
straight on to the grill shelf. This is  
useful when you are browning the  
top of food such as cauliflower  
cheese.  
7
C S I G 3 1 6  
Preheating  
You don't usually need to preheat the grill. You may wish to preheat it for  
a couple of minutes when you are cooking steak or browning food.  
Positioning food on  
the grid  
Place food such as toast, tea-cakes and  
muffins towards the centre of the grid.  
Place food which needs a gentle heat,  
such as tomatoes and mushrooms towards  
the edge of the grid.  
Arrange meat, meat products and fish to  
suit their thickness and how you like them  
cooked.  
8
C S I G 3 1 6  
The grill pan and handle  
The grill pan is supplied with a removable handle.  
To attach the handle, place the wirework under the cut out in the pan so  
that the metal plate hooks over the top of the grill pan.  
Slide the handle to the left and over the central bump on the grill pan.  
Ensure the handle is correctly located. It is not necessary to  
remove the grill pan handle during grilling.  
Place the grill pan on the shelf so that the pan is positioned centrally  
beneath the grill.  
To remove the handle, slide the handle to the right and lift the handle  
away from the cut out on the grill pan.  
Note  
If you require an additional handle for your grill pan, this can be ordered  
from Parkinson Cowan by quoting part number 311479800\6.  
9
C S I G 3 1 6  
Heat control  
The hotplate control knobs turn  
anticlockwise from 'OFF' to 'HIGH'  
and then to 'LOW'. You can adjust  
the heat by turning the control  
between the highest and lowest  
settings. These are shown as a  
large and a small flame symbol.  
Burner sizes  
The hotplate has three burner sizes  
to suit different types of cooking:  
Largest burner (Rapid) - use a large  
pan for food such as chips.  
Medium burners (Normal) - use for  
everyday cooking.  
Small burner (Simmer) - use for  
simmering food such as soups and  
stews.  
The largest pan which you should use on any burner is 230mm (9").  
The base of the smallest pan should not measure less than 100mm (4").  
10  
C S I G 3 1 6  
For your safety  
1
2
3
Take care to avoid burns and scalds when you are  
reaching across the hotplate.  
Use pans with flat bases. They are more stable than  
pans which are warped.  
Do not use pans with very heavy handles which cause  
the pan to tip.  
4
5
Put pans on the centre of the burners.  
Position pan handles so they cannot be accidentally  
knocked.  
6
Take extra care when you are deep fat frying. Do no
cover the pan with a lid.  
Do not leave a pan unattended. If the pan catches fire,  
leave it where it is and turn off all controls.  
Place a damp cloth or a fitting lid over the pan to  
smother the flames.  
Never put water on the fire.  
Leave the pan to cool for 30 minutes.  
7
If you are using a Wok we recommend it has a flat base  
as it will stand stable on the pan supports. If you use a  
round based Wok with a collar support, the collar must  
be of the open wire work type. A closed collar will affect  
the performance of the burner. Before you use the Wok  
make sure that the collar is stable on the pan supports.  
Always follow the instructions that come with the Wok.  
11  
C S I G 3 1 6  
Helpful hints  
1
Keep flames under the base of the pans. If the  
flames lick round the sides of the pans you are  
wasting gas.  
2
3
Only heat the amount of liquid you need. Do  
not overfill pans.  
Cover pans with a lid whenever possible. The  
food will heat up more quickly and there will be  
less steam in the kitchen.  
4
5
6
Try cooking more than one vegetable in the  
same pan, for example potatoes and carrots.  
Cut vegetables into smaller pieces. This wa
they will cook more quickly.  
A pressure cooker will save time and energy.  
12  
C S I G 3 1 6  
The oven  
Before you use the oven you should wipe it out with a damp cloth to  
remove any dust.  
Heat zones  
There are zones of heat within the oven. The  
temperature in the middle is the gas mark  
you have chosen. The top of the oven is  
slightly hotter and the lower shelf slightly  
cooler. The base of the oven is quite a lot  
cooler. You can make use of these heat  
zones when you are cooking foods that need  
different temperatures all at the same time.  
If you are cooking more than one tray of similar items, for example  
cakes or biscuits, swap the trays around during cooking. Or you can  
remove the top tray when the food is cooked and move the lower tray to  
the higher shelf to finish cooking.  
Preheating  
You do not need to preheat the oven when casseroling and so on.  
Preheat the oven for baking or when you are cooking sensitive food  
such as Yorkshire puddings, soufflés and yeast mixtures.  
When you are cooking or reheating frozen or chilled food read the  
instructions on the packing.  
When you need to preheat the oven, we recommend you do so for  
20 minutes.  
Oven shelves  
You can slot the oven shelves into any of five  
positions. Positions are counted from the top  
downwards.  
For safety the shelf will only pull out so  
far. If you want to remove a shelf completely  
pull it forward as far as it will go, raise the  
front edge and lift it out. To put the shelf into  
a different position keep the front edge  
raised, slot the shelf on to the runner, lower  
the front edge and slide the shelf in.  
13  
C S I G 3 1 6  
Baking trays and dishes  
For your safety  
Never place cooking dishes, trays  
and so on over the oven burner.  
This will damage the cooker as  
well as the ovenware and possibly  
the floor covering underneath the  
cooker.  
Leave a gap of 13mm (½")  
between all dishes and the sides of  
the oven so the heat can circulate  
properly.  
Do not push dishes too far back  
as food will burn if it overhangs the  
burner flames.  
For the best results we recommend that you use a baking tray which is  
310mm (12") square. If you use a tray or tin which is larger than this,  
you may need to turn the food around during cooking.  
Place single dishes on the centre of the shelf. You may need to turn  
large items around during cooking.  
Roasting  
For best results we recommend open roasting using minimal fat or oil to  
prevent splashing.  
It is not necessary to cover meat or poultry or wrap food in foil when  
roasting as this restricts the circulation of heat and will lead to extended  
cooktimes.  
If you are using a roasting bag or cover chicken breast with foil, be  
prepared to allow an extra 10 - 15 minutes for each 1/2kg (1lb).  
When cooking large items such as turkeys, the use of foil may be  
required to prevent the breast becoming dry before the rest of the bird is  
fully cooked.  
Condensation  
Condensation may form on the cooker. This is quite normal and nothing  
to worry about. The condensation forms when heat and moisture are  
present, for example during cooking. Whenever possible try to make  
sure that food which contains a lot of moisture, for example casseroles,  
are covered. If you do notice any condensation, wipe it up straight away.  
14  
Oven cooking chart  
These instructions are for cooking in the oven after it has been pre-heated for 20 minutes.  
If you are cooking more than one tray of similar items, for example cakes or biscuits, swap the trays around during cooking. Or you  
can take the top tray out of the oven when the food is cooked and move the lower tray to the higher shelf to finish cooking.  
Always leave at least one shelf position between shelves to allow heat to circulate.  
The recommended shelf positions give the best results.  
Put the dishes in the centre of the shelf.  
You can change the gas marks and cooking times to suit your own tastes.  
It is important to check that food is piping hot before serving.  
Gas  
Shelf  
Approximate  
Food  
mark  
position cooking time  
Roasting meat:  
Beef  
5
4
Rare:  
Medium:  
Well Done:  
20 mins. per ½kg (1lb) and 30 mins.  
25 mins. per ½kg (1lb) and 25 mins.  
30 mins. per ½kg (1lb) and 30 mins.  
Lamb  
5
5
4
4
Medium:  
Well Done:  
25 mins. per ½kg (1lb) and 25 mins.  
30 mins. per ½kg (1lb) and 30 mins.  
Pork and Veal  
Medium:  
Well Done:  
30 mins. per ½kg (1lb) and 30 mins.  
35 mins. per ½kg (1lb) and 35 mins.  
Thaw frozen joints thoroughly before cooking them.  
Oven cooking chart  
Oven cooking chart  
Gas  
Shelf  
Approximate  
Food  
mark  
position cooking time  
Poultry:  
Chicken  
5
4
4
5
4
4
20 mins. per ½kg (1lb) and 20 mins.  
Turkey below 4.5kg (10lbs)  
over 4.5kg (10lbs)  
Duck and duckling  
25 mins. per ½kg (1lb) and 25 mins.  
15 mins. per ½kg (1lb) and 15 mins.  
25 mins. per ½kg (1lb)  
4 or 5  
4
Stuffed poultry  
Cook as above but calculate weight including stuffing.  
Thoroughly thaw frozen joints before cooking them.  
The times given above are for open roasting in a preheated oven. If you cover the food with foil or a lid allow an extra 10 - 15 minutes for  
each ½kg (1lb).  
Yorkshire pudding - large  
- individual  
7
7
1
1
25-30 mins.  
15-25 mins.  
Cakes:  
Christmas cake (8")  
Rich fruit, 180mm (7")  
205mm (8")  
Madeira, 180mm (7")  
Small cakes  
2
2
2
4
5
7
4
3
3
4
4 - 5 hours  
2¼-2½ hours  
2½-2¾ hours  
1 hour  
15-25 mins.  
10-20 mins.  
1 & 3  
1 & 3  
Scones  
Victoria sandwich  
180mm (7")  
205mm (8")  
4
4
2 & 4  
2 & 4  
20-30 mins.  
20-35 mins.  
Gas  
mark  
Shelf  
position  
Approximate  
cooking time  
Food  
Pastries:  
Plate tart (shortcrust)  
Fruit pie (shortcrust)  
Mince pies (flan pastry)  
6
6
5
1
1
25 -35 mins. To help pastry brown on the underside  
25-35 mins. cook on a metal plate, or if plates are flat  
15-25 mins. and have no rim underneath, place on  
baking tray.  
2 & 4  
Puddings:  
Milk pudding  
Baked sponge pudding  
Baked custard  
2
4
3
3
3
3
2 hrs.  
45-60 mins.  
50-60 mins.  
Bread 0.45kg (1lb loaves)  
0.90kg (2lb loaves)  
Rolls and buns  
8*  
8*  
8*  
3
3
2
30-40 mins.  
30-40 mins.  
10-20 mins.  
* Note: When baking bread cook at gas mark 8 for 10 minutes before reducing to Gas mark 6 for remainder of cook time.  
Note: You must soak dried beans then boil them in an open pan for 15 minutes before you add them to any dish.  
Oven cooking chart  
C S I G 3 1 6  
Slow cooking  
The slow cook setting gives a very low heat in the oven. It is  
particularly useful when cooking soups, stews and casseroles because  
the long slow cooking will make cheaper, tougher cuts of meat more  
tender.  
You need to cook food at gas mark 6 for 30 minutes before you turn  
the oven down to a slow cook setting. This makes sure that the  
temperature of the food gets hot enough to start the food cooking.  
Some foods such as pastry and biscuits are not suitable for slow  
cooking because the temperature is too low.  
Cover all food during cooking to prevent it from drying out. You can  
uncover food for the last half hour if it is normally served golden brown.  
Food preparation-slow cooking  
Joints of meat and poultry  
Do not cook meat joints over 2.7kg (6lb).  
Do not cook poultry over 2kg (4lb 8oz).  
Cook on the middle shelf of the oven or above.  
Cook stuffing separately.  
Cook for a minimum of 6 hours.  
Joints of pork must only be cooked if you can make sure, by using a  
meat thermometer, that an internal temperature of at least 88oC has  
been reached .  
For good air circulation always stand joints on a rack in the roasting  
tin or casserole.  
Thaw all frozen meat and poultry before cooking.  
Prime cuts of meat do not benefit from slow cooking.  
Remove excess fat and skin unless browned first.  
Cook for 30 minutes at gas mark 6, then reduce to the slow cook  
setting.  
18  
C S I G 3 1 6  
Soups, casseroles and stews  
Do not cook casseroles over 3kg (6lb).  
Bring to the boil on the hotplate then cook on slow cook.  
Cook in the middle of the oven or above.  
Vegetables  
Cut into small pieces.  
Dried beans must be pre-soaked then boiled in an open pan for 15  
minutes before adding to any dish.  
Place vegetables under meat in casseroles.  
Cook for 30 minutes at gas mark 6, then reduce to the slow cook  
setting.  
Milk puddings  
Cover the cereal with boiling water and allow to stand for 30 minutes.  
Drain and make the pudding in the usual way.  
Cook for 30 minutes at gas mark 6, then reduce to the slow cook  
setting.  
General points for slow cooking  
Frozen foods  
Thaw thoroughly before cooking.  
Thickening  
Toss meat in flour for casseroles. Blend cornflour with water and add it  
at the end of cooking.  
Flavouring  
Flavours are retained because there is little evaporation. Adjust at the  
end of the cooking time.  
Liquid  
Reduce normal liquid quantities slightly as there is little evaporation  
during cooking.  
Milk and milk products, for example cream  
Add towards the end of the cooking to prevent curdling.  
Reheating  
Left over food should be cooled quickly and refrigerated.  
Food should not be reheated using the slow cook setting. Reheat  
conventionally or in a microwave. Food must only be reheated once.  
19  
C S I G 3 1 6  
For your safety  
For hygiene and safety reasons you must keep this gas cooker  
clean. A build up of fat or other foodstuff could cause a fire.  
Try to mop up spills and splashes as soon as they happen. But  
be careful as parts of the cooker will be hot.  
Do not use any polishes, caustic cleaners, abrasives, washing soda or  
soap except those recommended.  
Please note: If we recommend you use hot  
soapy water we mean hot water with  
washing up liquid in it and not any other  
cleaning product.  
If you own a dishwasher please read the  
operating instructions for the machine before  
you wash any part of your cooker in it.  
Clean your cooker regularly using a cloth that has been wrung out in  
hot soapy water. Rinse and polish it dry using a soft cloth.  
When you remove parts of your cooker for cleaning do not plunge  
them into water whilst they are very hot as this may damage the finish  
of the parts.  
Cleaning the handles  
It is strongly recommended that only hot soapy water is used for  
cleaning the door handles.  
The hotplate  
Clean the hotplate top using a mild abrasive such as 'Jif'. Take care not  
to damage the spark electrodes. If the spark electrodes are damaged  
the burners will not light.  
You can remove the pan supports, burner caps and burner crowns  
to clean them. Again take care not to damage the spark electrodes.  
If any food spills during cooking you can place the pan on another  
burner to finish cooking. Then you can remove the dirty parts and clean  
them before the spill 'burns on'.  
20  
C S I G 3 1 6  
You can wash the removable parts in very hot soapy water. You may  
use mild abrasives. Make sure that the electrode and the hole and slots  
in the crown are not blocked with food or cleaning materials.  
Clean the burner crowns by soaking them in very hot soapy water.  
You can remove any stubborn stains by scouring with a soap filled pad  
such as 'Brillo'. If you look after the burner crowns in this way they will  
stay reasonably clean. However the surface will dull with time.  
Aluminium based saucepans can leave shiny metal marks on the pan  
supports. Clean the pan supports regularly to remove the marks using a  
mild abrasive like 'Jif' with a soft scourer. For more stubborn marks you  
can use a soap-filled pad such as 'Brillo'.  
After cleaning the cooker parts, dry them  
thoroughly before you put them back.  
When replacing hotplate burner parts  
1. Crown to body (Do not try to force the  
crown on to the body).  
Make sure that the hole in the crown is  
over the electrode. Check that the two  
longer location pegs sit in the slots in the  
body. When the crown is in this position  
let it fall freely on to the body. Check that  
the crown can be moved slightly from  
side to side.  
2. Cap to crown  
Place cap centrally on the top of the  
crown (enamel side up). Move sideways  
and front to back to check the cap is  
properly fitted.  
3. Check for ignition  
If a burner will not light then you need to  
check the crown and cap positions.  
The grill  
Clean the grill compartment frequently using hot soapy water.  
After use you can soak the grill pan for a few minutes and then clean  
it using mild abrasives or a soap filled pad such as 'Brillo'.  
Clean the shelf using hot soapy water. Mild abrasives can be used if  
necessary.  
21  
C S I G 3 1 6  
The oven  
The inside of the oven is finished in vitreous enamel. You should clean  
the oven regularly using hot soapy water and mild abrasives or a soap  
filled pad such as 'Brillo'. If you use any oven cleaners they must have  
the Vitreous Enamel Development Council (VEDC) seal of approval.  
Follow the instructions on the cleaning agent and protect the oven  
burner with aluminium foil to prevent it becoming blocked.  
General  
Clean the oven shelves and the oven door while they are still slightly  
warm. This way you can easily remove any splashes and spills. Wipe  
with a cloth that has been wrung out in hot soapy water. You may use  
mild abrasives.  
Cleaning between the outer and inner  
door glass.  
You can remove the glass from the oven and grill doors if you need to.  
Note: For top oven door it is important not to open the door when the  
glass is removed because the door is lighter and it will spring shut.  
To remove the outer glass  
1 Open the door so you can get at the two cross head screws on the  
top of the door.  
Note: Open top oven door slightly to access screws.  
2 Loosen these two screws using a pozidrive screwdriver.  
3 You should hold the door glass securely in place with one hand,  
whilst removing the screws completely, with the other hand. If you do  
not do this, the door glass could fall forward.  
4 Using both hands, gently tilt the top of the door glass towards you.  
Lift it slightly to disengage the locators at the bottom of the door.  
22  
C S I G 3 1 6  
5 Clean the outer and inner glass using hot soapy water and mild  
abrasives such as 'Jif'. DO NOT try to clean the aluminium foil which  
is inside the door. The foil is there to keep the door cool, if it is  
damaged it will not work.  
6 Replace the glass by holding it in both hands and gently placing the  
locators into the holes of the brackets at the bottom of the door, and  
make sure the screw location holes line up.  
7 Hold the glass in place with one hand and replace the cross head  
screws into the location holes, with the other hand.  
8 Tighten the screws using a pozidrive screwdriver. Close the door.  
Cleaning The Door Glass  
To prevent damaging or weakening the door glass panels avoid  
the use of the following:  
Household detergents and bleaches  
Impregnated pads unsuitable for non-stick saucepans  
Brillo/Ajax pads or steel wool pads  
Chemical oven pads or aerosols  
Rust removers  
Bath/Sink stain removers  
If the door glass panel becomes chipped or has deep scratches  
the glass will be weakened and must be replaced to prevent the  
possibility of the panel shattering. Please contact your local  
Service Centre who will be pleased to advise further.  
23  
C S I G 3 1 6  
Installing the cooker  
For your safety  
This cooker must be installed and serviced by a competent person as  
stated in the Gas Safety (Installation & Use) regulations current editions  
and the IEE Wiring Regulations.  
It is important that the cooker is suitable for your gas supply.  
Your installer should check the data badge.  
Make sure that a stability bracket is fitted.  
Location  
For your safety  
The use of a gas cooking appliance results in the production of heat  
and moisture in the room in which it is installed. Ensure that the kitchen  
is well ventilated: keep natural ventilation holes open or install a  
mechanical ventilation device (mechanical extractor hood).  
Prolonged intensive use of the appliance may call for additional  
ventilation, for example opening of a window, or more effective  
ventilation, for example increasing the level of mechanical ventilation  
where present.  
For further details see page 33.  
24  
C S I G 3 1 6  
Positioning  
The diagram shows how close to the cooker cupboards, shelves,  
curtains and so on can be fitted. Check the diagram and carefully read  
the instructions to make sure your cooker is fitted safely. If you are in  
doubt your installer will give you advice.  
Do not fit any materials which may catch fire for example wood or  
curtains behind the cooker.  
Base units which are higher than the hotplate must be 100mm away.  
If a cooker hood is fitted read the cooker hood installation  
instructions.  
We recommend that cabinets fitted next to or above the cooker meet  
British Standards. Your installer will give you advice if you are not  
sure.  
Cooker dimensions  
Overall Height :  
902mm-920mm  
(adjusted by four screw feet)  
498mm  
600mm (to front of door panel)  
Width:  
Depth:  
25  
C S I G 3 1 6  
General information  
For your safety  
Do not block any of the cooker vents.  
Never line any part of the cooker with aluminium foil.  
Don't let items which can catch fire or electric mains leads  
such as kettle flexes trail over any part of the cooker.  
Moving your cooker  
You may damage some soft or badly fitted floor coverings when you  
move the cooker. The floor covering under the cooker should be  
securely fixed so it does not ruck up when you move the cooker across  
it. Alternatively you could remove the floor covering.  
To move the cooker open the grill door. Raise the cooker off its front  
feet by lifting it from inside the grill. Pull the cooker forward. When you  
replace the cooker push it back to the stop and make sure there is the  
same gap at each rear corner.  
The battery  
The battery for the ignition will usually  
last for many months. If the ignition  
system doesn't work you probably need  
to replace the battery.  
The battery is at the base of the  
cooker on the left-hand side of the front.  
You can see it through the slots between  
the oven and the plinth.  
When you need to replace the  
battery, open the main oven door, turn  
the battery holder clockwise about its  
pivot point. The battery you need is AA  
size.  
When you fit the new battery, make sure  
the positive end (marked with a + sign) is  
next to the (+) sign on the battery holder.  
Return the battery holder to its original  
position by turning it anti-clockwise.  
You can light the burners with a  
match until you have time to change  
the battery.  
26  
C S I G 3 1 6  
For your safety  
Do not try to disconnect the cooker from the gas supply if the  
supply pipe does not have a bayonet connection, as described in  
the installation instruction. If this is the case contact the person  
who installed the cooker.  
27  
C S I G 3 1 6  
What is wrong and why?  
We strongly recommend that you carry out the following checks on your  
cooker before calling a Service Engineer.  
Problem  
The oven, grill or hotplate will not light.  
Check  
If only the hotplate burners will not light make sure that the burner  
parts have been placed correctly. See instructions on page 21.  
If you cannot hear any sparking or the sparking is slow when you  
press the ignition button the battery probably needs replacing. For  
instructions on how to do this see page 26. You can light the burners  
with a match until you have time to change the battery.  
Check that there is not a problem with your gas supply. You can do  
this by making sure that other gas appliances such as your central  
heating or gas fire are working.  
Problem  
Food is cooking too quickly or too slowly.  
Check  
Check that you are using the recommended gas marks and shelf  
positions. See page 15. Be prepared to adjust the gas mark up or  
down to achieve the results you want.  
Problem  
The oven is not cooking evenly.  
Check  
Check that the cooker is installed properly and is level.  
Check that you are using the recommended temperatures and shelf  
positions.  
Problem  
Having difficulty cleaning any part of the cooker.  
Check  
Check that the instructions for care and cleaning, beginning on page  
20 are being followed.  
28  
C S I G 3 1 6  
Service and spare parts  
In the event of your appliance requiring service or if you wish to  
purchase spare parts please contact your local Parkinson Cowan  
Service Force Centre by telephoning  
0 8 7 0 5 9 2 9 9 2 9  
Your call will be routed to the Service Force Centre covering your  
postcode area.  
Parkinson Cowan customers in Ireland should telephone (01) 4090755  
Before you call an engineer check through the information under the  
heading 'What is wrong and why? '  
In-guarantee customers should ensure that the checks  
under the heading 'What is wrong and why?' have been  
made as the engineer will make a charge if the fault is not a  
mechanical or electrical breakdown.  
Please note that it is necessary to provide proof of purchase  
for any in-guarantee service calls.  
When you report a problem try to describe the nature of the fault.  
Always give your cooker's full name, model and serial number.  
Make a note of this information in this space:  
Name:  
Model Number:  
Serial Number:  
G.C. Number:  
29  
C S I G 3 1 6  
For your safety  
Maintenance must only be carried out by a competent /qualified  
person. Do not try to repair or alter/modify the cooker yourself as  
this could be dangerous.  
We recommend that your cooker has an annual gas safety  
check carried out by our approved service organisation.  
Customer Care Department  
For general enquiries concerning your Parkinson Cowan cooker or  
further information on products, you are invited to contact our Customer  
Care Department by letter or telephone as follows:  
Customer Care Department  
Parkinson Cowan  
55-77 High Street  
Slough  
Berkshire  
SL1 1DZ  
Tel: 08705 950950 *  
* calls to this number may be recorded for training purposes.  
The Gas Consumers' Council  
The Gas Consumers' Council (GCC) is an independent organisation  
which protects the interests of gas users.  
If you need advice, you will find the telephone number in your local  
telephone directory under Gas.  
30  
C S I G 3 1 6  
INSTALLATION INSTRUCTIONS  
Serial number on  
front frame. Data badge on  
top rear of panel.  
Please note that the handle may differ in type and shape from that shown in the diagram.  
For your safety  
Natural Gas and L.P. Gas versions of this appliance are available.  
Check that this model is suitable for the type of supply available.  
In the interest of safety this appliance must be installed and/or  
serviced by a competent person, as stated in the Gas Safety  
(Installation and Use) Regulations Current Editions.  
31  
C S I G 3 1 6  
TECHNICAL DATA  
DIMENSIONS  
Height  
907mm (nominal)  
Width  
498mm  
Depth  
600 mm  
Height to hotplate  
(to front of  
door panel)  
Space for fixing at hotplate level  
Minimum space above hotplate  
2mm minimum clearance  
787mm (If a cooker hood is fitted refer to the cooker hood  
installation instructions).  
Space for fixing above hotplate level  
Weight of appliance  
Minimum distance from rear wall  
See important note "Location of Appliance", page 34.  
48.4kg.  
1mm  
CONNECTIONS  
Gas  
Rear left hand side of appliance at hotplate level.  
Rc½ (½" B.S.P. female).  
None  
Electric  
IGNITION  
Spark generator  
Battery  
APCO 6BG 6893  
1.5 Volt AA size  
GRILL  
Natural Gas  
3.3kW (11263 Btu/h)3.0kW (215g/h)  
138 88  
L.P. Gas  
Heat Input  
Injector Marking  
HOTPLATE  
Natural Gas  
R.H.R.  
R.H.F.  
L.H.R.  
L.H.F  
Heat Input  
1.0kW  
2.0kW  
2.0kW  
2.8kW  
(3412 Btu/h)  
079  
(6824 Btu/h)  
104  
(6824 Btu/h)  
104  
(9554 Btu/h)  
130  
Injector Marking  
L.P.Gas  
2.0kW  
(143.7 g/h)  
072  
Heat Input  
1.0kW  
(71.8 g/h)  
051  
2.0kW  
(143.7 g/h)  
072  
2.7kW  
(194.0 g/h)  
083  
Injector Marking  
32  
C S I G 3 1 6  
MAIN OVEN  
Heat Input  
Natural Gas  
L.P. Gas  
2.4kW (172.4 g/h)  
2.4kW (8189Btu/h)  
Injector Marking  
108  
78  
Flame Supervision Device  
Thermostat  
Thermostat By-pass Marking  
Diamond'H' GSD 100/28  
Diamond'H' 1100157/B2  
69  
Diamond 'H' GSD-100-30  
Diamond'H' 1100-98/B2  
78  
GENERAL  
Ignition  
Spark Gap  
H. T. Spark  
3-4mm  
IMPORTANT - SAFETY REQUIREMENTS  
This appliance must be installed in accordance with the Gas Safety (Installation and Use) Regulations  
Current Editions. Detailed recommendations are contained in the following British Standard Codes of Practice  
- BS. 6172, BS.5440: Part 2 and B.S.6891. All British Standards must be 'Current Editions'.  
PROVISION FOR VENTILATION  
This appliance is not connected to a combustion products evacuation device. It shall be installed and  
connected in accordance with the current installation regulations. Particular attention shall be given to the  
relevant requirements regarding ventilation.  
The room containing the appliance should have an air supply in accordance with BS. 5440: Part 2 Current  
Edition. All rooms require an openable window or equivalent and some rooms will require a permanent vent  
as well. For room volumes up to 5m³ an air vent of 100cm² is required: for room volumes between 5m³ and  
10m³ an air vent of 50cm² is required. If the room has a door that opens directly to the outside, no air vent is  
required. For room volumes that exceed 11m³ no air vent is required. If there are other fuel burning  
appliances in the same room, BS.5440: Part 2 Current Edition should be consulted to determine the requisite  
air vent requirements.  
Prolonged intensive use of the appliance may call for additional ventilation, for example opening a window, or  
more effective ventilation, for example increasing the level of mechanical ventilation where present.  
33  
C S I G 3 1 6  
LOCATION OF APPLIANCE  
This appliance must not be installed in a bed-sitting room of volume less than 20m³ or in a bathroom, shower  
room or garage. It is essential that the appliance is positioned as stated below (see Fig. 1) i.e. shelves, wall  
cabinets and cooker hoods must be fitted a minimum of 787mm directly above the top of hotplate and 400mm  
above the hotplate when fitted in line with the outside of the appliance. If the units are intended to be fitted  
adjacent to the appliance but less than 400mm above the hotplate, then a minimum space of 100mm must be  
maintained between the sides of the unit and the appliance (see Fig.1a). Curtains must not be fitted  
immediately behind the appliance or within 150mm of the sides of the hotplate. If fitted next to or between two  
base units a minimum space of 1mm must be left between each unit and the sides of the appliance. The  
hotplate must be set to minimum of 7mm above the adjacent units. (Note: The levelling feet fitted to the  
appliance will achieve a nominal height of 907mm -5+13mm). Base units not meeting the above conditions  
must be a minimum of 100mm away from the hotplate. L.P.G. cookers MUST NOT be installed below  
ground level, i.e in a basement, or aboard any boat, yacht or other vessel.  
less  
100  
than  
400  
Fig.1  
All dimensions in mm  
Fig.1a  
34  
C S I G 3 1 6  
INSTALLATION  
1. PARTS REQUIRED  
The loose hotplate parts and battery are packed in the polystyrene fitment on top of the hotplate.  
2. LEVELLING THE APPLIANCE  
Adjustable levelling feet at the front and at the rear are provided on the base of the appliance.  
Adjustment to suit floor conditions is obtained by rotating in or out the hexagonal feet from the underside of  
the appliance.  
A spirit level should be placed on one of the oven shelves to confirm that the appliance is correctly levelled.  
3. FITTING THE STABILITY BRACKET  
It is recommended that if the appliance is to be installed with a flexible supply pipe a stability bracket  
(SK.4729.A) is fitted and is available from your supplier (see Important Safety Requirements, Page 33).  
These instructions should be read in conjunction with the leaflet packed with the stability bracket.  
1. Place the appliance in its intended position and level appliance.  
2. Mark off 250mm from the left hand side of the appliance as shown in dimension 'A', Fig 3a. This is the  
centre line of the fixing bracket.  
3. Draw a line 100mm from the front edge of the levelling feet (see Fig 3a) and remove appliance from its  
position. Mark off dimension 'B' (see Fig 3a) back from this line on the centre line of the bracket to locate the  
front edge of the lower bracket. Fix lower bracket (with two fixing holes) to the floor then measure the height  
from floor level to engagement edge on back of appliance, dimension 'C' of Fig. 3b.  
4. Assemble upper bracket to lower bracket so that underside of bracket is dimension 'C' +3mm above floor  
level. (see Fig. 3b).  
Reposition appliance and check that top bracket engages into appliance back as shown in Fig. 3b.  
20mm  
100mm  
(C)  
(A)  
250mm  
Fig.3a  
Fig.3b  
35  
C S I G 3 1 6  
4. CONNECTING TO GAS  
This appliance is designed to be installed with an appliance  
flexible connection only. Supply piping should not be less than  
R³/8. Connection is made to the Rc½ (½" B.S.P.) female  
threaded entry pipe located just below the hotplate level on the  
rear left hand side of the appliance. NOTE: ONLY LIQUID Fig.4  
SEALANTS TO BE USED WHEN INLET GAS PIPE IS  
FITTED I.E.: DO NOT USE P.T.F.E. SEALANT TAPE.  
Check for gas soundness after connecting the gas supply.  
The gas bayonet connector must be fitted in the shaded area  
indicated in Fig. 4. Take into account that it must be possible to  
pull the appliance forward sufficiently. The hose must not get  
caught on the stability bracket.  
IMPORTANT: FLEXIBLE TUBING USED MUST COMPLY  
WITH BS. 669 CURRENT EDITION.  
250  
L.P.G. FLEXIBLE CONNECTIONS MUST BE OF A TYPE  
225  
All dimensions in mm  
SUITABLE FOR L.P.G. AND CAPABLE OF OPERATION  
UP TO 50 mbar AND TO CARRY A RED STRIPE, BAND  
OR LABEL.  
5. FITTING THE BATTERY  
Fig.5  
1. The battery is located on the left hand side of the front  
plinth and can be viewed through a slot in the bottom  
left hand corner of the front frame( Fig .5).  
2. To gain access to the battery, open the main oven  
door, rotate the battery holder clockwise.  
3. Fit the battery AA size ensuring the positive, + terminal  
is on the right hand side as shown in the diagram.  
Return the battery to original position by turning it  
anti-clockwise.  
6. PRESSURE TESTING  
1
The oven injector is used as a pressure test point.  
Remove the oven furniture. Remove oven burner box retaining clips (one spring clip from each side) and  
remove box front cover. Replace one clip back into the right hand side of the burner box.  
Remove oven burner by removing the spring clip from the right hand side of the oven burner and slide  
burner off injector, whilst easing it forward and taking care not to strain the F.S.D. phial.  
2. Connect the pressure gauge to the oven injector.  
3. Check the supply pressure by turning the thermostat on and one hotplate tap full on and light the  
appropriate burner. The pressure should be either:-  
(i) For Natural Gas 20mbar  
(ii) For LP.Gas The pressure must be set to 28 mbar for use on butane or 37 mbar for use on propane.  
4. Turn off the taps, disconnect the pressure gauge and replace oven burner and cover, ensuring that the  
F.S.D. phial is correctly located into the bracket on the burner.  
5. Check operation of oven.  
7. CHECKING THE GRILL  
Place the grill pan containing the grid into the grill compartment. Light the grill burner by turning the grill tap full  
on and pressing the ignition button on the fascia panel. As soon as the burner is lit the button can be  
released.  
36  
C S I G 3 1 6  
8. CHECKING THE HOTPLATE  
Fit the burner crowns and caps ensuring that they are correctly seated. Fit the pan supports. Check each of  
the hotplate burners in turn by turning the hotplate tap to it's full on position and pressing the ignition button.  
As soon as the burners are lit the button can be released.  
9. CHECKING THE MAIN OVEN  
1.  
Turn the oven thermostat knob to Mk 9 and press the ignition button. As soon as the burner is alight the  
button can be released.  
2.  
3.  
There should now be a low gas rate to the burner, which is the F.S.D. by pass rate.  
When the F.S.D. phial has heated up it opens the F.S.D. valve which allows the main gas supply to the  
oven burner.  
4.  
5.  
After 1 minute check that the flame covers the full width of the burner and is stable.  
Set the oven control to Mk 2, close the oven door and check that after about 10 minutes the flame size  
has reduced.  
6.  
Turn off the control and check that the oven flames go out.  
GENERAL NOTE  
Instruct the user on how to use the appliance and its ignition system. Refer the user to the wording in the  
inside cover which gives advice on the safe operation of the appliance.  
37  
C S I G 3 1 6  
CSIG316 311508704  
Contents Check List  
Note:  
If you require replacements of the item listed below please contact your local Service  
Force Centre quoting the relevant part number.  
No. OFF  
DESCRIPTION  
2
1
1
1
1
1
4
4
2
1
Oven Shelves  
Hotplate Operation Card  
Grill pan (small) DIP (311409401)  
Grill Pan Trivet (small wire) (311419801)  
Detachable grill pan handle (311468100)  
Grill Shelf  
Burner Crowns  
Burner Caps  
Pan Supports  
Battery  
Note:  
If you require an additional handle for your grill pan, this can be ordered from your local  
Service Force Centre by quoting part number 311479800\6.  
This handbook was correct on the date it was printed. But this handbook will be  
replaced if the specification or appearance changes during production.  
No.  
Off  
Maker's Part  
Number  
Description  
Burner Cap - Rapid  
1
2
1
1
1
2
1
2
354000610  
354000609  
354000608  
359039100  
337000302  
337000402  
337000502  
359033202  
Burner Cap - Normal  
Burner Cap - Simmer  
Burner Crown - Rapid - N.G.  
Burner Crown - Rapid - L.P.G.  
Burner Crown - Normal  
Burner Crown - Simmer  
Pan Support  
NOTE : Failure to use manufacturers original spares could negate normal BSI approval of the product  
Parkinson Cowan  
Customer Care  
55 - 77 High Street, Slough, Berkshire, SL1 1DZ  
Telephone: 0870 5 950950  
Drawing No. 311508704  
© Electrolux Household Appliances Limited 2000  
From the Electrolux Group. The world's No. 1 choice.  
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use.  
More than 55 million Electrolux group products (such as refrigerators, cookers, washing machines, vacuum cleaners,  
chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries  
around the world.  

HP Hewlett Packard HP 55HP User Manual
Grundig Computer Hardware HMS470 User Manual
GE JP200 User Manual
Epson S5U1C62000A User Manual
Dell M993c User Manual
Cypress CY7C1382DV25 User Manual
AT T EL51250 User Manual
ASRock Computer Hardware Motherboard User Manual
Akai FACTORY PRESET MPK49 User Manual
Acura Embedded Power Brick CV User Manual