AT T 847868304 User Manual

User's Manual

for Cordless Answering

System Telephone 7610

CHARGING

HANDSET IN USE

MEMO/REWIND

CLOCK

AST FWD

PLA

Y/ST

Fold open this manual for information about this

telephone's installation and operation. Please

read Part 1 – Important Product Information,

included in this package

OLUME

Part 2

Printed in Mexico. Issue L4

847868304

I N S T A L L A T I O N

Base Antenna (extended)

Cover

Turn system

on or off.

CHARGING

HANDSET IN USE

MEMO/REWIND

CLOCK

AST FWD

Lift panel door

to access features

(see figure at right).

PLA

Y/ST

Record or play

outgoing anouncement

Audible clock; also use with

CHANGE to set time/day.

OLUME

Use with other

buttons to

Adjust message playback volume.

change settings

Fast forward

during message

playback.

Play messages or

stop message playback

Save

messages.

should be on steady. If the light is

flashing rapidly, the microcassette is

not installed properly. Remove the

cassette, and check to see if it's

damaged. It it's okay, install it

again. After you have installed the

PLAY/ STOP

base goes on to show the handset is

in the right position to charge the

batteries. The batteries will be fully

charged in 14 hours.

P (wait for dial tone), p,

#, #, #. 3. To return to touch tone

dialing with touch tone service,

when the phone is off, press P

(wait for dial tone), p, #, #,

#, 8.

Check for dial tone.

cassette, press

the system.

to reset

Make sure the base antenna is

upright. After the batteries are

charged, pick up the handset and

check for dial tone by pressing

P; the PHONE light should

go on and you should hear a dial

tone. Press P to hang up.

IMPORTANT: After you have installed

the 7610, you will need to record an

announcement that callers will hear when

the system answers. Please see the

Answering System Operation section of

this manual.

CAUTION: Use only the power

supply provided with this prod-

uct. To obtain a replacement, call Lucent

Technologies at 1 800 222-3111.

LucentTechnologies Power Supply DAS-2.

Input: 120V, 60Hz, 15W.

10 Set the dial mode.

Output: 9V AC, 780 mA.

If you have touch tone service, the

phone will be ready to use as soon

as the battery is charged.

Charge the handset batteries be-

fore use.

Place the handset face down in the

base. The CHARGING light on the

If you have dial pulse service, you’ll

need to set the dial mode. Press

B A T T E R I E S

CAUTION: To reduce the risk of

Replacing the Handset

Charging the

fire or injury to persons or

damage to the telephone, read and follow

these instructions carefully.

Battery Pack

Handset Battery Pack

Remove the battery case cover on

the handset by pressing on the

indentation and sliding the cover

downward.

The batteries need charging when:

•

The phone beeps four times when you

press P.

The LOW BATTERY light on the

handset flashes on and off.

The phone does not respond when you

press P, and no lights go on.

•

Use Lucent Technologies Replace

ment Battery 4051 in the handset.

Do not dispose of the battery in a fire.

The cell might explode.

Do not open, puncture or mutilate the

battery. Released electrolyte is

corrosive and might cause damage to

the eyes or skin. It might be toxic if

swallowed.

Lift out the old battery pack and

unplug it from the handset.

Hold the new battery pack and plug

the connector into the handset.

Place the battery pack into the case, so

the wires rest above the battery pack.

Replace the cover by sliding it on its

track up over the battery case until it

snaps firmly into place.

The new batteries must be charged

before using the phone. Place the

handset face down in the base and

allow it to charge for 14 hours. The

telephone might operate before that,

but for best performance, let the

handset batteries charge fully.

Place the handset in the base so the

CHARGING light goes on. The batteries will

be fully charged in 14 hours.

NOTE: The handset must lie flat in the base,

with the keypad facing down, when charg-

ing. The charging light in the base goes on if

the handset is positioned correctly.

A fully charged battery maintains standby

power for up to 14 days when the Handset

Ringer ON/OFF switch is set to ON, and up

to 21 days when the Handset Ringer ON/OFF

switch is set to OFF.

If it’s more convenient for you, you can leave

the handset in the base all the time.

It is impossible to overcharge the batteries.

If you get a low battery indicator even after

the batteries have been charged 14 hours, the

battery should be replaced.

Battery Case

Battery Pack

Wires

Battery Pack

Wires

Battery Case Cover

I N C A S E O F D I F F I C U L T Y

If you have difficulty operating this phone,

try the suggestions below. If you still have

trouble, call Lucent Technologies at

1 800 222-3111.

•

Place the handset in the base,

and check to make sure the

CHARGING light is on.

•

Make sure the base antenna is upright.

Disconnect the base from the tele-

phone jack and plug in a corded

telephone. If you still hear noise or

interference, the problem is probably

in your wiring or local service. Call

your local telephone service company.

Unplug the AC adapter from the

outlet, wait 15 seconds, then plug

it in again. The CHARGING light

should go on. Wait another 15

seconds, then pick up the handset

and press P. The phone

should operate properly. If it does

not, try the next step.

If the phone does not work at all, check

these items first

•

Make sure the power cord is plugged

into the base and an electrical outlet

not controlled by a wall switch.

Make sure the telephone line cord is

plugged firmly into the base unit

and the telephone jack.

If the phone does not beep, or beeps

four times when you press P, the

batteries might need recharging.

If the handset LOW BATTERY light

is flashing, the batteries need

recharging.

If the phone does not ring when you receive

a call

•

Make sure the Handset Ringer ON/

OFF switch is set to ON.

Make sure the telephone line cord is

connected firmly to the base and the

telephone jack.

Make sure the power cord is plugged

into an outlet not controlled by a wall

switch.

You might be too far from the base.

Move closer to the base.

You might have too many extension

phones on your telephone line to allow

all of them to ring. Try unplugging

some of the other phones.

Press C to change to

another channel.

•

Pick up the handset, open the

battery compartment, and unplug

the battery pack. Wait 15

•

seconds, then reinstall the battery

pack, close the battery compart

ment, place the handset in the

base, and check to make sure the

CHARGING light is on. Wait

another 15 seconds, then pick up

the handset and press P.

The phone should operate

•

Make sure the battery pack is

installed correctly.

If the battery pack will not charge,

try cleaning the charge contacts with

an eraser. If the battery pack will

still not charge, replace it with

Lucent Technologies Replacement

Battery 4051.

properly.

If you have no dial tone, check all the previ-

ous suggestions. If you still do not hear a dial

tone, disconnect the phone and try another

phone in the same jack. If there is no dial

tone on that phone either, the problem is prob-

ably in your wiring or local service. Call your

local telephone service company.

•

If the above suggestions do not solve

the problem, try resetting the

security code (see next section).

If your telephone misdials or you don’t hear

the other person right away

•

It might take a few seconds for your

handset to find a good connection to

the phone system. While it is search

ing, the PHONE light blinks rapidly.

Do not start dialing until the PHONE

light is on steadily.

If you have dial pulse (rotary) service,

you’ll need to set the dial mode to dial

pulse. Press P, p, #, #,

#, 3.

If you have TONE service and you

hear strange clicks while you are

dialing, you’ll need to set the dial

mode to touch tone. Press P,

p, #,#, #, 8.

If you hear a two-beep signal when you

try to use the handset

If you hear noise or interference when

using the phone

•

The handset and base are not

communicating properly. You might

be out of range while attempting to

dial. Move closer to the base and try

the call again.

•

You may be out of range. Move closer

to the base.

•

Press and release Cto change to

another of the 25 channels available. If

the noise is exceptionally loud, move

closer to the base before changing

channels.

Household appliances plugged into

the same circuit as the base can

sometimes cause interference. Try

moving the appliance or the base to

another outlet.

•

If moving closer to the base does

not help, the handset and base

might be set to different security

codes.To reset the security code, try

the following:

•

Place the handset in the base,

and check to make sure the

CHARGING light is on. Wait

15 seconds, then pick up the

handset and press P. The

phone should operate properly.

If it does not, try the next step.

If the Message Light flashes rapidly

•

The layout of your home or office

might be limiting the operating range.

Try moving the base to another

location, preferably on an upper floor.

If the system does not play messages

PLAY/ STOP

when you press

, check

the cassette to see if it is broken or

jammed. If so, replace the cassette,

PLAY/ STOP

then press

system.

to reset the

I N C A S E O F D I F F I C U L T Y

•

Try sliding the Volume control on the

side of the base upward to increase

volume.

If the system does not respond to remote

commands

If you have difficulty hearing messages

•

If messages are garbled, the recording

heads may be soiled and should be

cleaned.

•

Make sure you are calling from a

touch tone telephone. If you hear

clicks when you dial, the phone is not

a touch tone phone.

If the recording tape sticks or malfunctions

•

Unplug the system from the

electrical outlet.

Use only high-quality MC-30 or

MC-60 microcassette tapes.

If the tape has been used for an

extended period, it may be worn and

should be replaced.

•

There might be noise or interference

on the phone line you are using. Press

dial buttons firmly.

•

Remove the cassette tape.

Use any good tape deck

cleaning kit, and follow the

manufacturer's instructions

— OR —

•

Make sure you are entering your

Remote Access Code correctly.

A power failure might have caused the

Remote Access Code to revert to its

original setting.

If the system does not answer after the

correct number of rings

•

Rub the front face of the record-

ing heads lightly with a soft,

clean cotton swab moistened

slightly with isopropyl

alcohol.

If the Ring Select switch is set to TS,

the system answers after 4 rings when

you have no new messages, and after

2 rings when you have new messages.

The system might be off, or the tape

might be full. In either of these cases,

the system answers after 10 rings.

The tape might be missing, broken, or

incorrectly installed.

•

Use any cleaning fluid

sparingly. If you spill fluid into

the interior, unplug power and

line cords and let the system dry

thoroughly before using.

•

O P E R A T I O N

to the base for recharging. You can still use

the handset to make a call or to answer a call

if you hear an extension phone ringing.

Making A Call

Press P, and wait for the

PHONE light to go on steadily.

When you hear a dial tone, dial the

number.

When the ringer ON/OFF switch is set to

ON, the handset stays ready to use for up to

14 days in standby mode.

NOTE: You might experience a slight de-

lay before you hear a dial tone, as the

AutoSelect^®feature searches for a clear

channel.

Handset Volume

The handset volume can be set to three dif-

ferent levels. Each time you press V the

level changes.

Answering a Call

If this phone is ringing and the handset

is in the base, lift the handset. The PHONE

light goes on, and the call is connected.

Temporary Tone

NOTE: If you have touch tone service, you do

not need to use the Temporary Tone feature.

NOTE: If the ringer switch is set to OFF,

press P to answer the call.

If you have dial pulse (rotary) service, this

feature allows you to enter codes or tones

needed to operate answering machines, or to

use electronic banking services, calling cards,

and other special services. This feature will

operate most special services; however, some

services may actually require a touch tone

line. To be sure, ask the company that

provides the special service.

Light is on while

you're on a call.

• If the handset is out of the base,

press P. The PHONE light

goes on, and the call is connected.

• Although ringing stops when you

answer, you might not be able to

hear the other party until the

Make and answer calls.

PHONE light goes on steadily.

Store/access numbers

in memory locations.

Dial the call, then press * (tone). Any

dial buttons pressed after this send

tone signals.

Ending a Call

To end a call, place the handset into the base

or press P.

Temporary Tone

After you hang up, the phone auto

matically returns to dial pulse (rotary)

dialing

Redial

The last number dialed (up to 16 digits) on

this phone is stored in redial memory until

you dial another number.

Change channels.

Mute

Mute allows you to hear your caller, but pre-

vents the caller from hearing you.

While on a call:

Press P, and wait for the

PHONE light to go on.

When you hear a dial tone, press

•

Press M. The MUTE light goes on.

To deactivate the Mute feature :

•

Press M again. The MUTE light

goes off.

Battery Saver Control

Feature/Ringer ON-OFF

Flash

Set the switch on the side of the handset to

Press F to activate custom-calling

services such as Call Waiting or 3-Way

Calling. You may have to press other

buttons before or after F as explained

in custom-calling instructions provided by

your local telephone service company.

OFF to prevent the handset from ringing.

When the ringer switch is set to OFF, the

handset stays ready to use for up to 21 days

in standby mode before you have to return it

M E M O R Y

This cordless phone can store 10 telephone

numbers that you can dial just by pressing

p and one of the number buttons.

Additionally, the 7610 offers a memory lo-

cation accessed by pressing m.

NOTE: Each pause you store is counted as

a digit. You can store up to 16 digits in each

memory location.

For example, to store 9, PAUSE,

555-1234 in memory location 3:

Press p, 9, (hold the 9

for 2 seconds, until a second beep is

heard.) Then press 5 5 5 1 2 3 4

p 3.

Storing Speed-Dial Numbers

Light goes on when

battery needs recharging

Make sure the PHONE light is off.

Press p.

Enter the phone number (up to 16

digits).

Dialing Speed-Dial Numbers

Press p.

Press P.

Press p.

Press any number button from 0 to 9

for the memory location where the

number is to be stored.

Mute handset microphone.

Press the number button (0-9) you

assigned to the number you’re calling.

For example, to dial the number

stored in location 9, press

P, p, 9.

A three-part tone confirms that the

number was stored properly. If you

hear a long buzzing tone, or nothing

at all, press P, then follow the

steps above to store the number

again.

Redial last number called.

Access telephone

subscriber services.

Dialing M1

Press P.

Press m.

Dial number stored in

M1 memory location.

For example, to store 555-1234 in

memory location 9:

Press p, 5, 5, 5,

1, 2, 3, 4, p, 9.

Adjust handset volume.

Storing Numbers Just Dialed

Whenever you make a telephone call, you can

store in memory the number you dialed. Press

R instead of entering the telephone

number when storing speed-dial numbers.

Storing a Number in M1

Make sure the PHONE light is OFF.

Press p.

Enter the phone number (up to 16

digits).

Press p.

Replacing a Stored Number

You can replace a stored number by

storing a new number in its place.

Memory Guard

NOTE: You may choose to store emergency

numbers in the memory locations. The

manufacturer assumes no responsibility for

customer reliance upon this memory feature.

The phone numbers you store in memory

are protected from loss when you change

the handset battery, or in the event of a

power failure.

Storing a Pause

In a Memory Dial Number

Directory Label

There is a directory label that you can use to

keep a record of names or telephone num-

bers of the numbers stored in memory loca-

tions.You can place this label on the handset

or the base.

When storing a number in memory, press

and hold down the number button that comes

before the pause, until you hear the second

beep. This inserts a 1.5 second pause after

that digit. If you hold the number button

down longer, you will hear more beeps as

additional pauses are stored.

O P E R A T I N G R A N G E

If you move out of range during a phone

conversation, you will hear noise or inter-

ference. To improve reception, move closer

to the base.

This cordless telephone operates at the

maximum power allowed by the Federal

Communications Commission (FCC).

Even so, the handset and base can com-

municate over only a certain distance —

which can vary with the locations of the

base and handset, the weather, and the

construction of your home or office.

Changing Channels

This cordless telephone has an advanced

25-channel AutoSelect^®feature that mini-

mizes the chance of interference. Every

time you answer or make a call, the

AutoSelect feature searches for and selects

a clear channel.

If you move out of range while on a call,

the phone will be left “off the hook.” To

hang up properly, walk back into range,

periodically pressing P until the

PHONE light goes off.

In the unlikely event that you notice noise

or interference while using the handset:

When you make a call, if the handset is at

to a point where the base and handset can

not communicate, the handset will sound

two short beeps, indicating that you are out

of range. Move closer to the base to re-

store normal operation.

Press C.

If the interference does not clear,

continue to press C until

you find a clear channel (your call

will not be interrupted

— OR—

If you receive a call while you are out of

range, the handset might not ring — or if

it does ring, the call might not connect

when you press P. Move closer to the

base, then press P to answer the call.

Move closer to the base and press

NOTE: You must be in range to change

channels.

ANSWERING SYSTEM OPERATION

Light goes on when

handset is in use or

battery is charging.

Fast forward

during message

playback.

CHARGING

HANDSET IN USE

Audible clock; also use with

MEMO/REWIND

CLOCK

CHANGE (under the cover)

AST FWD

to set time/day.

Blinking light indicates

messages are waiting.

PLA

Y/ST

Play messages or stop

Record a memo, or

rewind tape during

message playback

OLUME

message playback

Save

messages.

Adjust message playback volume.

Press and release g, located

under the microcassette cover.

Press and release A and

wait for the beep.

Volume Control

Setting the Clock

Use the volume control on the side of the

base to adjust the answering system

volume. Slide the control up toward the

back of the base to increase volume while

listening to your announcement or

messages, or down toward the bottom of

the base to decrease volume.

You’ll need to set the clock so that it can

record the day and time that each message

is received.

After the beep, speak toward the front

of the unit, from about 9 inches away.

PLAY/ STOP

Press and release g.

Press and release C. You

will hear a day of the week.

To change the day, hold down

Press and release

when you

are finished. The tape resets

automatically and plays the

announcement.

MEMO/ REWIND

FAST FWD

until you hear

the correct day, then release the button.

Press and release C. You

will hear an hour setting.

Recording Your

Announcement

To review your announcement — Press

and release A, located under the

microcassette cover.

Before using this answering system, you

need to record the announcement (up to 30

seconds long) that callers will hear when

the system answers a call. Your

announcement should tell callers that they

will hear a series of beeps, or one long beep,

before the system begins recording the

message.

To change the hour, hold down

MEMO/ REWIND

FAST FWD

until you hear

the correct hour, then release the button.

Press and release C. You

will hear a minutes setting.

Turning the System

On and Off

Press and release ON/ OFF located under the

microcassette cover. The PLAY/STOP

light is lit steadily or blinking slowly when

the system is on, and is unlit when the

system is off.

To change the minutes setting, hold

MEMO/ REWIND

FAST FWD

down

until you

hear the correct minutes setting, then

release the button.

Prepare an announcement.

For example: Hello. I can’t come to

the phone right now. Please leave

your name, telephone number, and

short message after you hear a series

of beeps or one long beep. I will

return your call as soon as I can.

Press and release C. You

will hear the day and time setting. If

it is incorrect, start over at Step 1.

NOTE: If the PLAY/STOP light flashes

rapidly, the tape might be missing

or broken. Check the tape, then press

To review the day and time — Press and

release C.

PLAY/ STOP

to reset the system.

ANSWERING SYSTEM OPERATION

played back with other messages.

Ring Select

Listening to Your Messages

MEMO/ REWIND

Hold down

. After

Use the Ring Select switch on the back side

of the base unit to select how many times

the line will ring before the system answers

a call. Set to 4 for four rings, or set to TS

for Toll Saver. When you set the system to

TS, the system answers after 4 rings when

you have no new messages, and after 2 rings

when you have new messages.

Before listening to your messages, set the

message volume control so you can hear

PLAY/ STOP

the beep, speak toward the front

of the base.

the messages. When you press

the

To stop recording, release

system announces the number of messages

received. After each message, the system

announces the day and time the message

was received. After playing the last

message, the system announces “End of

messages.”

MEMO/ REWIND

Call Screening/Intercept

Setthesystemtoanswercalls, andsetthevolume

control so you can hear the caller’s message.

Play messages — Press and release

Answering Calls

PLAY/ STOP

If you decide to take the call, you can do so

from the cordless handset or from any

telephone on the same line. The system

stops recording and resets to answer calls.

If the answering system doesn't disconnect

immediately, press the Fbutton on the

cordless handset or flash the switchhook

on another telephone.

When the system answers a call, the caller

hears the announcement you recorded,

followed by a single beep or a series of

beeps. After the final beep, the system

begins recording your caller’s message.

The system hangs up when the caller hangs

up or is silent for 7 seconds or after the

maximum message time of 4 minutes.

Clear messages — After you’ve

played your messages, the system

automatically resets to record new

messages over the old ones. The old

messages are not cleared until new

ones are recorded.

Save message — Press and release

SAVE

to save messages. The light

blinks to show that messages have

been saved.

Rewind — Hold down

When the Tape is Full

NOTE: If there are any messages recorded

on the tape, the caller hears a series of

beeps while the system goes to the end of

the last recorded message. To reduce the

number of beeps and the time it takes before

a caller can leave a message, listen to your

messages frequently, and do not save a

large number of messages.

When the tape is completely full, the system

cannot record a caller’s message. The system

answers calls after 10 rings and beeps twice,

but it does not play an outgoing

announcement or record the caller’s message.

MEMO/ REWIND

while the system is

playing messages. The tape rewinds

as long as you hold down the button.

Fast forward — Hold down

while the system is playing

FAST FWD

When the tape is full, you can play all of the

messages either locally or remotely and then

clear nessages — OR — you can turn the

tape over to record on the other side

— OR — you can change the microcassette.

messages. The tape fast forwards as

long as you hold down the button.

Interrupt message playback —

PLAY/ STOP

Bypassing the

Announcement

You might wish to let certain callers know

that they can leave a message without

listening to your announcement. Callers

can press # during the announcement and

then leave a message after the series of beeps.

Press and release

. To

continue playback, press and release

PLAY/ STOP

. (If you do not return

NOTE: If you turn the tape over or change

the tape, be sure to follow all the directions

in the next section.

to playing messages within 60

seconds, the system automatically

saves all messages and resets to

answer calls.)

Replay messages — Wait for the

tape to reset, then press and release

Changing the Microcassette

ON/ OFF

Message Light

Press and release

to turn

the system off.

PLAY/ STOP

The light above

indicates how

PLAY/ STOP

Remove the old cassette.

Turn the cassette over, or install

a new cassette.

many messages you’ve received. The light

blinks once for each message, pauses, and

blinks again. For example, if you have 5

messages, the light blinks 5 times, pauses,

then repeats.

Recording a Memo

You can record a memo to be stored as an

incoming message. The memo will be

ON/ OFF

Press and release

the system on.

to turn

After the tape resets, record a

new announcement if necessary.

ANSWERING SYSTEM OPERATION

After the two beeps, wait 4

seconds, and the system plays

back messages

FROM A REMOTE

TOUCH TONE PHONE

Recording a New

Announcement

Press 7, * after the two beeps.

— OR —

You will hear a series of short

beeps, then one long beep.

After the long beep, record your

new announcement..

When you finish, press and

release 5. The system plays

your new announcement.

To review your new

Press and release 1 to play

all of your messages (if there

are no messages, the system

announces “End of messages”)

— OR —

Press and release 2 to play

only new messages (if there are

no new messages, the system

announces “No new messages.”)

To replay — Press and release

1 after all messages have been

played.

Remote Access Code

The Remote Access Code is a 3-digit code

which lets you access your 7610 answering

system away from your home or office. The

factory setting is 123 (printed under the

microcassette lid on the base).You can

change this code to any 3-digit number

between 100 and 999, except 323 and 523.

You can only change the Remote Access

Code remotely; you cannot change it at the

base.

announcement, press 7, 1

after the two-beep signal.

Turning System On

When the system is off, it answers after

10 rings and beeps twice.

To rewind — Hold down 4 to

rewind. When you release 4,

the tape resumes playing from

its new position.

Changing Your Remote Access Code

Press 9, 9 after the two

beeps. The system beeps once.

Enter your new 3-digit Remote

Access Code. The system beeps

twice.

Press and release 0 to turn the

system on.

The system beeps twice to

indicate the system is on. To

leave a message, press and

release #. If you're not leaving

a message, hang up.

To skip messages — Hold

down 6 to fast forward. When

you release 6 the tape resumes

playing from its new position.

NOTE: A power failure may cause the

Remote Access Code to return to its original

setting.

To clear messages — Press 3,

3 after you hear the two-beep

signal. The tape rewinds and

resets to record new messages

over the old ones.

Turning System Off

Listening to Your Messages

Press 8, 8 after the two beeps.

Dial your telephone number

from a touch tone phone.

When the Tape is Full

When the tape is full, the system answers

after 10 rings and beeps twice.

When the system answers, enter

your Remote Access Code. The

system announces the number

of messages received, then

beeps twice. (If there are no

messages, the system announces

"No messages.")

To stop playback — Press and

release 5. To resume

playback, press and release 1.

Enter your Remote Access Code

within 15 seconds after the

beeps to listen to messages.

Press 3, 3 after you listen to

messages to clear them and

make room for new messages.

Answering System 7610

Operation From a Remote Touch Tone Phone

To access your answering system:

1 Dial your telephone number.

2 When the system answers, enter your 3-digit Remote Access

Code. The system announces the number of messages

received, then beeps twice and is ready to accept a command.

See the other side of this card for a complete list of remote

commands.

Answering System 7610

Operation From a Remote Touch Tone Phone

To access your answering system:

1 Dial your telephone number.

2 When the system answers, enter your 3-digit Remote Access

Code. The system announces the number of messages

received, then beeps twice and is ready to accept a command.

See the other side of this card for a complete list of remote

commands.

COMMAND

Play all messages

PRESS

Play only new messages

Replay messages

Rewind

after playing messages

Hold down

; release to play.

Fast Forward

Clear messages

Stop

; press

to play..

Record announcement

, speak after long beep,

to stop.

press

Change Remote Access Code

Turn system on

, enter new code.

Turn system off

COMMAND

Play all messages

PRESS

Play only new messages

Replay messages

Rewind

after playing messages

Hold down

; release to play.

Fast Forward

Clear messages

Stop

; press

to play..

Record announcement

, speak after long beep,

to stop.

press

Change Remote Access Code

Turn system on

, enter new code.

Turn system off

HP Hewlett Packard Hewlett Packard Computer Monitor LV2011 User Manual
Hotpoint 6500 User Manual
Grundig AMIRA32HDBLK User Manual
Fujitsu F2MC 8L F202RA User Manual
Envision Peripherals Envision H716A4 User Manual
Elo TouchSystems 1727L User Manual
Eizo FLEXSCAN S2433W User Manual
DFI U340 495 User Manual
Cannon Stratford 10931G User Manual
Acnodes PMW6190 User Manual1