AN9 32X
Motherboard
AMD Socket AM2
User’s Manual
ꢀ AMD Socket AM2
ATX Motherboard
ꢀ NB: NVIDIA C51XE
SB: NVIDIA MCP55PXE
ꢀ 2GHz HT
ꢀ Dual DDR2 800 DIMM Slots
ꢀ NVIDIA SLI Technology
ꢀ Dual PCI-E X16 Slots
ꢀ Dual GbE LAN
ꢀ IEEE 1394a
ꢀ 8x SATA 3Gb/s with RAID
ꢀ ABIT Guru™ Technology
ꢀ ABIT Silent OTES™ Technology
ꢀ 7.1 Channel HD Audio
About this Manual:
This user’s manual contains all the information you may
need for setting up this motherboard. To read the user’s
the “Driver & Utility CD” into the CD-ROM drive in your
system. The auto-run screen will appear, click the
“Manual” tab to enter its submenu. If not, browse the
root directory of the CD-ROM via the File Manager, and
double click the “AUTORUN” file.
Contents
AN9 32X
iii
iv
AN9 32X
1. Introduction
1.1 Features & Specifications
CPU
• Supports Socket 940 AM2 Processor with 2GHz system bus using Hyper-Transport™
Technology
• Supports AMD CPU Cool ‘n’ Quiet Technology
Chipset
• Northbridge: NVIDIA®C51XE Chipset
• Southbridge: NVIDIA® MCP55PXE Chipset
Memory
• Four 240-pin DIMM slots
• Supports Dual Channel DDR2 800 Un-buffered ECC/Non-ECC memory
• Supports maximum memory capacity up to 8GB
ABIT Engineered
• ABIT Guru™ Technology
• ABIT Silent OTES™ Technology
NVIDIA SLI Technology
• Two PCI-Express X16 slots support NVIDIA Scalable Link Interface
SATA 3Gb/s RAID
• Supports 6 ports NV SATA 3Gb/s RAID 0/1/0+1/5/JBOD
2nd SATA 3Gb/s RAID
• 1x Internal SATA 3Gb/s port
• 1x External SATA 3Gb/s port
Dual GbE LAN
• Dual NVIDIA® Gigabit Ethernet
IEEE 1394
• Supports 2 Ports IEEE 1394a at 400Mb/s transfer rate
Audio
• ABIT AudioMAX HD 7.1 CH
• Supports auto jack sensing and optical S/PDIF In/Out
Expansion Slots
• 2x PCI Express x16 slots
• 2x PCI Express x1 slots
• 1x PCI slot
AN9 32X
1-1
• 1x AudioMAX slot
Internal I/O Connectors
• 1x Floppy port
• 1x UDMA 133/100/66/33 connector
• 7x SATA connectors
• 3x USB 2.0 headers
• 2x IEEE1394a headers
Rear Panel I/O
• Silent OTES™
• 1x eSATA connector
• 1x PS/2 Keyboard connector
• 1x PS/2 Mouse connector
• 2x RJ-45 Gigabit LAN ports
• 4x USB 2.0 ports
RoHS Compliancy
• 100% Lead-free process and RoHS compliancy
Miscellaneous
• ATX form factor (305mm x 245mm)
※ Specifications and information contained herein are subject to change without
notice.
1-2
AN9 32X
1-4
AN9 32X
2. Hardware Setup
In this chapter we will elaborate all the information you need upon installing this motherboard
to your computer system.
※ Always power off the computer and unplug the AC power cord before adding or
removing any peripheral or component. Failing to so may cause severe damage
to your motherboard and/or peripherals. Plug in the AC power cord only after
you have carefully checked everything.
2.1 Choosing a Computer Chassis
•
This motherboard carries an ATX form factor of 305 x 245 mm. Choose a chassis big
enough to install this motherboard.
•
As some features for this motherboard are implemented by cabling connectors on the
motherboard to indicators and switches or buttons on the chassis, make sure your chassis
supports all the features required.
•
•
If there is possibility of adopting some more hard drives, make sure your chassis has
sufficient power and space for them.
Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O
shield of the chassis matches the I/O port configuration of this motherboard. You can find
an I/O shield specifically designed for this motherboard in its package.
2.2 Installing Motherboard
Most computer chassis have a base with
many mounting holes to allow the
motherboard to be securely attached, and at
the same time, protected the system from
short circuits. There are two ways to attach
the motherboard to the chassis base:
1. with studs,
2. or with spacers
In principle, the best way to attach the board
is with studs. Only if you are unable to do
this should you attach the board with spacers.
Line up the holes on the board with the mounting holes on the chassis. If the holes line up and
there are screw holes, you can attach the board with studs. If the holes line up and there are
only slots, you can only attach with spacers. Take the tip of the spacers and insert them into
the slots. After doing this to all the slots, you can slide the board into position aligned with slots.
After the board has been positioned, check to make sure everything is OK before putting the
chassis back on.
AN9 32X
2-1
To install this motherboard:
1. Locate all the screw holes on
the motherboard and the
chassis base.
2. Place all the studs or spacers
needed on the chassis base
and have them tightened.
3. Face the motherboard’s I/O
ports toward the chassis’s rear
panel.
4. Line up all the motherboard’s
spacers on the chassis.
5. Install the motherboard with
screws
tightened.
and
have
them
※ To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if
they are already fastened on the chassis base and are without mounting-holes
on the motherboard to align with.
2.3 Checking Jumper Settings
For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the
jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position.
SHORT
OPEN
OPEN
For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in.
Pin 1~2 SHORT
Pin 2~3 SHORT
2-2
AN9 32X
2.3.1 CMOS Memory Clearing Header and Backup Battery
The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b)
you forgot the supervisor or user password preset in the BIOS menu, (c) you are unable to
boot-up the system because the CPU ratio/clock was incorrectly set in the BIOS menu.
This header uses a jumper cap to clear the CMOS memory and have it reconfigured to the
default values stored in BIOS.
•
•
Pins 1 and 2 shorted (default): Normal operation.
Pins 2 and 3 shorted: Clear CMOS memory.
To clear the CMOS memory and load in the default values:
1. Power off the system and disconnect with AC power source.
2. Set pin 2 and pin 3 shorted by the jumper cap. Wait for a few seconds. Set the jumper cap
back to its default settings --- pin 1 and pin 2 shorted.
3. Power on the system.
4. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS setup
menu right after powering on system.
5. Set the CPU operating speed back to its default or an appropriate value.
6. Save and exit the BIOS setup menu.
AN9 32X
2-3
CMOS Backup Battery:
An onboard battery saves the CMOS memory to keep the BIOS information stays on even after
disconnected your system with power source. Nevertheless, this backup battery exhausts after
some five years. Once the error message like “CMOS BATTERY HAS FAILED” or “CMOS
checksum error” displays on monitor, this backup battery is no longer functional and has to
be renewed.
To renew the backup battery:
1. Power off the system and disconnect with AC power source.
2. Remove the exhausted battery.
3. Insert a new CR2032 or equivalent battery. Pay attention to its polarity. The “+” side is its
positive polarity.
4. Connect AC power source and power on the system.
5. Enter the BIOS setup menu. Reconfigure the setup parameters if necessary.
CAUTION:
※ Danger of explosion may arise if the battery is incorrectly renewed.
※ Renew only with the same or equivalent type recommended by the battery
manufacturer.
※ Dispose of used batteries according to the battery manufacturer’s instructions.
2-4
AN9 32X
2.3.2 Wake-up Headers
These headers use a jumper cap to enable/disable the wake-up function.
•
•
•
•
•
•
PS2-PWR1:
Pin 1-2 shorted (Default): Disable wake-up function support at Keyboard/Mouse port.
Pin 2-3 shorted: Enable wake-up function support at Keyboard/Mouse port.
USB-PWR1:
Pin 1-2 shorted (Default): Disable wake-up function support at USB1 port.
Pin 2-3 shorted: Enable wake-up function support at USB1 port.
USB-PWR2:
Pin 1-2 shorted (Default): Disable wake-up function support at USB2 port.
Pin 2-3 shorted: Enable wake-up function support at USB2 port
FP-PWR1:
Pin 1-2 shorted (Default): Disable wake-up function support at FP-USB1 port.
Pin 2-3 shorted: Enable wake-up function support at FP-USB1 port.
FP-PWR2:
Pin 1-2 shorted (Default): Disable wake-up function support at FP-USB2 port.
Pin 2-3 shorted: Enable wake-up function support at FP-USB2 port
FP-PWR3:
Pin 1-2 shorted (Default): Disable wake-up function support at FP-USB3 port.
Pin 2-3 shorted: Enable wake-up function support at FP-USB3 port
AN9 32X
2-5
2.4 Connecting Chassis Components
2.4.1 ATX Power Connectors
These connectors provide the connection from an ATX power supply. As the plugs from the
power supply fit in only one orientation, find the correct one and push firmly down into these
connectors.
ATX 24-Pin Power Connector:
The power supply with 20-pin or 24-pin cables can both be connected to this 24-pin connector.
Connect from pin-1 for either type. However, a 20-pin power supply may cause the system
unstable or even unbootable for the sake of insufficient electricity. A minimum power of 300W
or higher is recommended.
ATX 12V 4-Pin Power Connector:
This connector supplies power to CPU. The system will not start without connecting power to
this one.
Auxiliary 12V Power Connector:
This connector provides an auxiliary power source for devices added on PCI
Express slots.
2-6
AN9 32X
2.4.2 Front Panel Switches & Indicators Headers
This header is used for connecting switches and LED indicators on the chassis front panel.
Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure
below stands for positive polarity for the LED connection. Please pay attention when connecting
these headers. A wrong orientation will only cause the LED not lighting, but a wrong connection
of the switches could cause system malfunction.
•
•
•
•
•
•
HLED (Pin 1, 3):
Connects to the HDD LED cable of chassis front panel.
RST (Pin 5, 7):
Connects to the Reset Switch cable of chassis front panel.
SPKR (Pin 13, 15, 17, 19):
Connects to the System Speaker cable of chassis.
SLED (Pin 2, 4):
Connects to the Suspend LED cable (if there is one) of chassis front panel.
PWR (Pin 6, 8):
Connects to the Power Switch cable of chassis front panel.
PLED (Pin 16, 18, 20):
Connects to the Power LED cable of chassis front panel.
AN9 32X
2-7
2.4.3 FAN Power Connectors
These connectors each provide power to the cooling fans installed in your system.
•
•
•
CPUFAN1: CPU Fan Power Connector
SYSFAN1: System Fan Power Connector
AUXFAN1~4: Auxiliary Fan Power Connector
※ These fan connectors are not jumpers. DO NOT place jumper caps on these
connectors.
2-8
AN9 32X
2.5 Installing Hardware
※ DO NOT scratch the motherboard when installing hardware. An accidentally
tiny surface-mount component may seriously damage the
scratch of
motherboard.
a
2.5.1 CPU Socket AM2
※ DO NOT touch or bend the delicate pins on the CPU whenever you are holding it.
The installation procedures vary with different types of CPU fan-and-heatsink assembly. The
one shown here is served for DEMO only. For detailed information on how to install the one
you bought, refer to its installation guidelines.
1. Pull out the socket lever away from the
socket and fully lift it up over 90-degree
angle.
Locate and align the triangle mark with
both the CPU and the socket body.
Vertically place the CPU with its pin-side
down into the socket.
Be careful to insert the CPU into the
socket. The CPU only fits in one
orientation with the socket. DO NOT
force the CPU into the socket.
2. After placing the CPU into position, push
the socket lever down into its locked
position to secure the CPU. The lever
clicks when it’s locked into position.
3. The heatsink for CPU may have thermal
interface material attached to its
bottom. If not, applying a few squeeze
of thermal paste to the CPU die will help
to increase the contact.
AN9 32X
2-9
4. Place the heatsink and fan assembly
onto the retention frame. Match the
heatsink
clip
with
the
socket
mounting-lug. Hook the spring clip to
the mounting-lug.
5. On the other side, push the retention
clip straight down to lock into the plastic
lug on the retention frame.
6. Connect the CPU cooling fan power
cable to the CPUFAN1 connector on this
motherboard.
※ The “CPUFAN1” connector MUST be
connected with cooling fan, no
matter a 3-Pin or 4-Pin CPU Fan.
※ The motherboard in this illustration is served for DEMO only, may not be the
same type or model as the one described in this user’s manual.
※ A higher fan speed will be helpful for better airflow and heat-dissipation.
Nevertheless, stay alert to touch any heatsink since the high temperature
generated by the working system is still possible.
2-10
AN9 32X
2.5.2 DDR2 Memory Slots
This motherboard provides four 240-pin DIMM slots for Dual Channel DDR2 800 memory
modules with memory expansion size up to 8GB.
To reach the performance of Dual Channel DDR2, the following rules must be obeyed:
•
For a 2-DIMM dual-channel installation:
Populate DIMM modules of the same type and size on slots [DIMM1]+[DIMM2], or slots
[DIMM3]+[DIMM4].
•
For a 4-DIMM dual-channel installation:
Populate 2 DIMM modules of the same type and size on slots [DIMM1]+[DIMM2], and
another 2 DIMM modules of the same type and size on slots [DIMM3]+[DIMM4].
※ [DIMM1] and [DIMM2] slots are made of the same color.
[DIMM3] and [DIMM4] are made of another same color.
Usually there is no hardware or BIOS setup required after adding or removing memory modules,
but you will have to clear the CMOS memory first if any memory module related problem
occurs.
AN9 32X
2-11
To install system memory:
1. Power off the computer and unplug the AC power cord before installing or removing
memory modules.
2. Locate the DIMM slot on the board.
3. Hold two edges of the DIMM module
carefully, keep away from touching its
connectors.
4. Align the notch key on the module with
the rib on the slot.
5. Firmly press the module into the slots
until the ejector tabs at both sides of the slot automatically snap into the mounting notch.
Do not force the DIMM module in with extra force as the DIMM module only fits in one
direction.
6. To remove the DIMM modules, push the two ejector tabs on the slot outward
simultaneously, and then pull out the DIMM module.
※ Static electricity can damage the electronic components of the computer or
optional boards. Before starting these procedures, ensure that you are
discharged of static electricity by touching a grounded metal object briefly.
2.5.3 PCI Express X16 Add-on Slots (Install Graphics Card)
These slots support the connections of graphics cards that comply with PCI Express
specifications. This motherboard provides dual PCI-Express X16 slots for one or two graphics
cards installation:
One PCIE graphics card installation (Normal Mode):
Insert your PCIE graphics card into [PCIEXP1]
slot.
2-12
AN9 32X
Two PCIE graphics cards installation (SLI Mode):
To install two SLI-ready graphics cards under SLI Mode, you will need to:
•
•
•
Prepare two identical NVIDIA certified, SLI-ready PCI Express x16 graphics cards (the same
model from the same manufacturer).
Make sure the graphics card driver supports the NVIDIA SLI technology. Download the
Make sure your power supply unit is sufficient to provide the minimum power required.
※ The following illustration is served for DEMO only. All the devices, including the
motherboard, the graphics cards, the SLI Bridge Connector, or the SLI bracket,
may not be exactly the same type, shape, or model as the one you bought.
1. Insert two identical SLI-ready graphics
cards into both PCIEXP1 and PCIEXP2
slots.
※ The NVIDIA SLI technology
currently supports the Windows XP
operating system only.
2. Bridge connecting two graphics cards
with the “SLI Connector Card” (fit in
both direction).
Insert and secure the SLI supporting
bracket.
AN9 32X
2-13
2.5.4 AudioMAX Connection Slot
This slot provides the audio input/output connection over the rear I/O part through an add-on
daughter-card. Find your “AudioMAX” daughter-card and its driver in the motherboard
package.
•
•
S/PDIF Out: This connector provides an S/PDIF-Out connection through optical fiber to
digital multimedia devices.
S/PDIF In: This connector provides an S/PDIF-In connection through optical fiber to
digital multimedia devices.
Line-In: Connects to the line out from external audio sources.
•
•
Mic-In: Connects to the plug from external microphone.
Line-Out: Connects to the front left and front right channel in the 7.1-channel or regular
2-channel audio system.
•
•
Cen/Sub: Connects to the center and subwoofer channel in the 7.1-channel audio system.
R.L./R.R. (Rear Left / Rear Right): Connects to the rear left and rear right channel in
the 7.1-channel audio system.
•
•
S.L./S.R. (Surround Left / Surround Right): Connects to the surround left and
surround right channel in the 7.1-channel audio system.
CD1: This connector connects to the audio output of internal CD-ROM
drive or add-on card.
2-14
AN9 32X
•
FP-AUDIO1: This header provides the connection to audio connector
at front panel.
This header provides the front panel connection for HD (High Definition)
Audio, yet for AC’97 Audio CODEC connection, you must carefully check the
pin assignment before connecting from the front panel module. An incorrect
connection may cause malfunction or even damage the motherboard.
※ Please do not connect the
Pin Assignment
(HD AUDIO)
Pin Assignment
(AC’97 AUDIO)
“Ground” cable or “USB VCC”
cable from the front panel
module to the Pin 4 “AVCC”
of this header.
Pin
Pin
1
2
MIC2 L
1
2
MIC In
GND
AGND
3
MIC2 R
3
MIC Power
NC
4
5
AVCC
4
FRO-R
5
Line Out (R)
NC
Driver Configuration for AC’97
audio connection:
6
MIC2_JD
F_IO_SEN
FRO-L
6
7
7
NC
The audio driver is originally
configured to support HD Audio. For
AC’97 audio connection, you may:
9
9
Line Out (L)
NC
10
LINE2_JD
10
1. Right-click the “Realtek HD Audio Manager”
icon in system tray.
2. Click “Audio I/O” tab, and then click
“Connector Settings”.
AN9 32X
2-15
3. Click “Disabled front panel jack
detection”, and then click “OK” to confirm.
S/PDIF Connection:
In the motherboard package you can find one audio daughter-card and one optical-fiber cable.
•
S/PDIF Input Connection:
1. Remove the rubber protection-cap. Attach one end of the optical cable with the 3.5mm
Optical-to-Stereo adapter, and have it plugged into the [Line-In] jack on this
daughter-card. (This jack is served for either optical or line input.)
2. Connect the other end of the optical cable to the [Digital-Out] (SPDIF-Out) jack on your
digital multimedia device.
•
S/PDIF Output Connection:
1. Remove the rubber protection-cap. Plug one end of the optical cable into the
[SPDIF-Out] jack on this daughter-card.
2. Connect the other end of the optical cable to the [Digital-In] (SPDIF-In) jack on your
digital multimedia device.
2-16
AN9 32X
2.6 Connecting Peripheral Devices
2.6.1 Floppy and IDE Disk Drive Connectors
The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable.
Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two
connectors on the other end to the floppy disk drives connector. Generally you need only one
floppy disk drive in your system.
※ The red line on the ribbon cable must be aligned with pin-1 on both the FDC1
port and the floppy connector.
Each of the IDE port connects up to two IDE drives
at Ultra ATA/100 mode by one 40-pin, 80-conductor,
and 3-connector Ultra ATA/66 ribbon cables.
Connect the single end (blue connector) at the
longer length of ribbon cable to the IDE port of this
board, the other two ends (gray and black connector)
at the shorter length of the ribbon cable to the
connectors of your hard drives.
※ Make sure to configure the “Master” and “Slave” relation before connecting two
drives by one single ribbon cable. The red line on the ribbon cable must be
aligned with pin-1 on both the IDE port and the hard-drive connector.
AN9 32X
2-17
2.6.2 Serial ATA Connectors
Each SATA connector serves as one single channel to connect one SATA device by a thin SATA
cable.
•
SATA1~SATA6: Available for RAID 0, RAID 1, RAID 0+1, RAID 5, or RAID 10
configuration by the utility “Intel Matrix Storage Manager”.
•
SATA7、eSATA1: Available for RAID 0 or RAID 1 configuration by the utility “Sil3132 SATA
RAID Driver”.
To connect SATA device:
1. Attach either end of the signal cable to
the SATA connector on motherboard.
Attach the other end to SATA device.
2. Attach the SATA power cable to the
SATA device and connect the other end
from the power supply.
※ The motherboard in this illustration is served for DEMO only, may not be the
same type or model as the one described in this user’s manual.
2-18
AN9 32X
2.6.3 Additional USB 2.0 Port Headers
Besides the 4x USB 2.0 ports located at rear I/O part, this motherboard also features 3x more
USB 2.0 headers onboard. Each header supports 2x additional USB 2.0 ports by connecting
bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis.
Pin
1
Pin Assignment
VCC
Pin
2
Pin Assignment
VCC
3
Data0 -
4
Data1 -
Data1 +
Ground
NC
5
Data0 +
Ground
6
7
8
10
※ Make sure the connecting cable bears the same pin assignment.
2.6.4 Additional IEEE1394 Port Headers
Each header supports 1x additional IEEE1394 port by connecting bracket or cable to the rear
I/O panel or the front-mounted IEEE1394 port of your chassis.
Pin
1
Pin Assignment
TPA0 +
Pin
2
Pin Assignment
TPA0 -
3
Ground
4
Ground
5
TPB0 +
6
TPB0 -
7
+12V
8
+12V
10
Ground
※ Make sure the connecting cable bears the same pin assignment.
AN9 32X
2-19
2.7 Onboard Status Display
2.7.1 POST Code Displayer
This is an LED device to display the “POST” Code, the acronym for Power On Self Test. The
computer will execute the POST action whenever you power on the computer. The POST
process is controlled by the BIOS. It is used to detect the status of the computer’s main
components and peripherals. Each POST Code corresponds to different checkpoints that are
also defined by the BIOS in advance. For example, “memory presence test” is an important
checkpoint and its POST Code is “C1”. When the BIOS execute any POST item, it will write the
corresponding POST Code into the address 80h. If the POST passes, the BIOS will process the
next POST item and write the next POST Code into the address 80h. If the POST fails, we can
check the POST Code in address 80h to find out where the problem lies.
This LED device also displays the “POST” Code of AC2005, an “uGuru” chipset developed
exclusively by ABIT computer.
※
The decimal point lights up during the AC2005 POST action.
See Appendix for both AWARD and AC2005 POST Code definitions.
2-22
AN9 32X
2.7.2 Power Source Indicators
These indicators work as a reminding device to display the power status of this motherboard
with power source connected.
•
5VSB:
Lights On: Your ATX power supplier is connected with power source, and its power switch
is on.
Lights Off: Your ATX power supplier is not connected with power source, or connected with
power source but its power switch is off.
•
•
VCC:
Lights On: The system power is on.
Lights Off: The system power is off.
SLI_PWR1:
Lights On: The system power is on.
Lights Off: The “ATX4P1” connector is connected with power source from your ATX power
supplier.
AN9 32X
2-23
2.8 Connecting I/O Devices
•
Silent OTES™: The Silent OTES™ (Silent Outside Thermal Exhaust System) is a device
specifically designed to silently cool the motherboard's North Bridge chipset.
(Keep the area for outgoing heat wave open.)
•
•
•
•
•
eSATA1: This connector supports the external SATA connection.
Mouse: Connects to PS/2 mouse.
Keyboard: Connects to PS/2 keyboard.
LAN1/LAN2: Connects to Local Area Network.
USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse,
keyboard, hub, digital camera, joystick etc.
2-24
AN9 32X
3. BIOS Setup
This motherboard provides a programmable EEPROM so that you can update the BIOS utility.
The BIOS (Basic Input/Output System) is a program that deals with the basic level of
communication between processor and peripherals. Use the BIOS Setup program only when
installing motherboard, reconfiguring system, or prompted to “Run Setup”. This chapter
explains the Setup Utility of BIOS utility.
After powering up the system, the BIOS message appears on the screen, the memory count
begins, and then the following message appears on the screen:
PRESS DEL TO ENTER SETUP
If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt>
+ <Del> keys, or by pressing the Reset button on computer chassis. Only when these two
methods fair should you restart the system by powering it off and then back on.
After pressing <Del> key, the main menu screen appears.
Phoenix – Award BIOS CMOS Setup Utility
► uGuru Utility
► PnP/PCI Configurations
Load Fail-Safe Defaults
Load Optimized Defaults
Set Password
► Standard CMOS Features
► Advanced BIOS Features
► Advanced Chipset Features
► Integrated Peripherals
► Power Management Setup
Save & Exit Setup
Exit Without Saving
Esc: Quit
F10: Save & Exit Setup
F6 : Save PROFILE To BIOS
↓↑→←
: Select Item
(C51XE/MCP55-6A61JA1BC-00)
F7 : Load PROFILE From BIOS
OC Guru & ABIT EQ
※ In order to increase system stability and performance, our engineering staff is
constantly improving the BIOS menu. The BIOS setup screens and descriptions
illustrated in this manual are for your reference only, and may not completely
match with what you see on your screen.
AN9 32X
3-1
3.1 µGuru™ Utility
There are two setup menus in this µGuru utility. You may switch between these two by clicking
the left or right arrow key on keyboard:
3.1.1 OC Guru
µGuru Utility V1.00
OC Guru
AMD Athlon(tm) 64 X2 Dual Core Processor 3800+
Frequency : 2000MHz
Item Help ►
CPU Operating Speed
X - Multiplier Factor
X - External Clock
X - PCIE Clock
2000(200)
x10.0
Auto
100 MHz
Voltages Control
Auto Detect
1.3500V
1.85 V
1.20 V
1.20 V
1.50 V
1.20 V
-20 mv
X - CPU Core Voltage
X - DDR2 Voltage
X - NB 1.2V Voltage
X - NB PCIE 1.2V Voltage
X - SB 1.5V Voltage
X - HyperTransport Voltage
X - DDR2 Reference Voltage
Power Cycle Statistics
Press Enter
↓↑→←:Move Enter:Select +/-/PU/PD:Value
F10:Save ESC:Exit
Brand Name
This item displays the CPU model name installed on this motherboard.
Frequency
This item displays the processor speed of the CPU installed on this motherboard.
CPU Operating Speed
This item displays the CPU operating speed according to the type and speed of your CPU. You
can also select the [User Define] option to enter the manual option.
User Define:
※ The wrong settings of the multiplier and external clock in certain circumstances
may cause CPU damage. Setting the working frequency higher than the PCI
chipset or processor specs, may cause abnormal memory module functioning,
system hangs, hard disk drive data lose, abnormal functioning of the VGA card,
or abnormal functioning with other add-on cards. Using non-specification
settings for your CPU is not the intention of this explanation. These should be
used for engineering testing, not for normal applications.
※ There will be no guaranty for the settings beyond specification. Any damage of
any component on this motherboard or peripherals resulting therein is not our
responsibility.
3-2
AN9 32X
-
Multiplier Factor
This item displays the multiplier factor for the CPU you installed.
External Clock
-
This item selects the external clock frequency. Due to the specification limit of the CPU you
installed, the speed you set over its standard bus speed is supported, but not guaranteed.
-
PCIE Clock
This item selects the clock frequency for PCI Express slot.
Voltages Control
This option allows you to switch between the default and user-defined voltages. Leave this
setting at default unless the current voltage setting cannot be detected or is not correct. The
option “User Define” enables you to select the following voltages manually.
-
-
-
-
-
-
-
CPU Core Voltage
DDR2 Voltage
NB 1.2V Voltage
NB PCIE 1.2V Voltage
SB 1.5V Voltage
HyperTransport Voltage
DDR2 Reference Voltage
Power Cycle Statistics
Click <Enter> key to enter its submenu:
µGuru Utility V1.00
OC Guru
Power Cycle Statistics
PC Up Time
0 Hours
Item Help ►►
PC Up Time Total
PC Reset Button Cycles
PC Power Cycles
AC Power On Total Time
AC Power Cycles
119 Hours
123 Cycles
538 Cycles
288 Hours
228 Cycles
↓↑→←:Move Enter:Select +/-/PU/PD:Value
F10:Save ESC:Exit
These items display the power cycle statistics for each element.
AN9 32X
3-3
3.1.2 ABIT EQ
Click right-arrow <→> key to switch from OC Guru setup menu to ABIT EQ setup menu:
µGuru Utility V1.00
ABIT EQ
ABIT EQ Beep Control
► Temperature Monitoring
► Voltage Monitoring
► Fan Speed Monitoring
► FanEQ Control
Enabled
Item Help ►
Press Enter
Press Enter
Press Enter
Press Enter
↓↑→←:Move Enter:Select +/-/PU/PD:Value
F10:Save ESC:Exit
ABIT EQ Beep Control
This item allows you to enable or disable ABIT EQ Beep Control function.
ꢀ
Temperature Monitoring
Click <Enter> key to enter its submenu:
µGuru Utility V1.00
ABIT EQ
Temperature Monitoring
Reading Shutdown Shutdown Beep
Beep
Enable Temp. Enable Temp.
(*)CPU Temperature
(*)System Temperature
(*)PWM Temperature
34°C/93°F (*)
29°C/84°F ( )
36°C/96°F ( )
85°/185°F (*)
65°°C/149°F (*)
90°°C/194°F (*)
75°C/167°F
55°C/131°F
88°C/176°F
↓↑→←:Move Enter:Select +/-/PU/PD:Value
CPU Temperature/System Temperature/PWM Temperature
F10:Save ESC:Exit
These items display the temperature of CPU, System, and Power Module.
3-4
AN9 32X
-
Shutdown Enable
Use <Space> key to enable system shutdown function. If the CPU/System/PWM’s temperature
exceeds the shutdown temperature limit, the system will shutdown automatically.
-
Shutdown Temp.
This item sets the temperature that will shutdown the system automatically in order to prevent
system overheating.
-
Beep Enable
Use <Space> key to enable warning beeps function. Once the system has detected that the
CPU/System/PWM’s temperature exceeded the beep temperature limit, warning beeps will
sound.
-
Beep Temp.
This item selects the warning temperature limit.
※ The shutdown temperature must be set above the warning temperature.
ꢀ
Voltage Monitoring
Click <Enter> key to enter its submenu:
µGuru Utility V1.00
ABIT EQ
Voltage Monitoring
Reading Shutdown Beep
Enable
1.40 V (*)
High
Enable Limit
Low
Limit
(*)CPU Core Voltage
(*)DDR2 Voltage
(*)DDR2 VTT Voltage
(*)HyperTransport Voltage
(*)NB Voltage
(*)CPU VDDA 2.5V Voltage
(*)SB Voltage
(*)ATX +12V (24-Pin Connector)
(*)ATX +12V (4-Pin Connector)
(*)ATX +5V
(*)
(*)
(*)
(*)
(*)
(*)
(*)
(*)
(*)
(*)
(*)
(*)
1.60 V
0 V
1.80 V ( )
0.90 V ( )
1.20 V ( )
1.20 V ( )
2.50 V ( )
1.50 V ( )
12.00 V ( )
12.00 V ( )
5.00 V ( )
3.30 V ( )
5.00 V ( )
2.20 V 1.50 V
1.10 V 0.75 V
1.45 V 0.95 V
1.45 V 0.95 V
3.00 V 2.00 V
1.00 V 1.20 V
14.40 V 9.60 V
14.40 V 9.60 V
6.00 V 4.00 V
3.95 V 2.65 V
6.00 V 4.00 V
(*)ATX +3.3V
(*)ATX 5VSB
↓↑→←:Move Enter:Select +/-/PU/PD:Value
F10:Save ESC:Exit
All Voltages
These items display the voltage of each element.
Shutdown Enable
-
Use <Space> key to enable system shutdown function. If the voltage of corresponding element
is higher/lower than the high/low limit, the system will automatically shutdown.
AN9 32X
3-5
-
Beep Enable
Use <Space> key to enable warning beeps function. If the voltage of corresponding element is
higher/lower than the high/low limit, warning beeps will sound.
-
High/Low Limit
These items set the high and low voltage limit.
※ The value of high limit must be set above the one of low limit.
ꢀ
Fan Speed Monitoring
Click <Enter> key to enter its submenu:
µGuru Utility V1.00
ABIT EQ
Fan Speed Monitoring
Reading
Shutdown Beep
Enable Enable
7440 RPM (*)
Low
Limit
(*)CPU FAN Speed
( )SYS FAN Speed
( )AUX1 FAN Speed
( )AUX2 FAN Speed
( )AUX3 FAN Speed
( )AUX4 FAN Speed
(*)
( )
( )
( )
( )
( )
300 RPM
300 RPM
300 RPM
300 RPM
300 RPM
300 RPM
N/A
N/A
N/A
N/A
N/A
( )
( )
( )
( )
( )
↓↑→←:Move Enter:Select +/-/PU/PD:Value
F10:Save ESC:Exit
CPU/SYS/AUX1~4 FAN Speed
These items display the speed of the fans connected to CPU, SYS, and AUX1~4 FAN headers.
Shutdown Enable
-
Use <Space> key to enable system shutdown function. Once the system has detected that the
fan speed is lower than the low limit value, system will shutdown automatically.
-
Beep Enable
Use <Space> key to enable warning beeps function. If the fan speed is lower than the low limit
value, warning beeps will sound.
-
Low Limit
These items set the low limit of fan speed.
3-6
AN9 32X
ꢀ
FanEQ Control
µGuru Utility V1.00
ABIT EQ
FanEQ Control
► CPU FanEQ Control
► SYS FanEQ Control
► AUX1 FanEQ Control
► AUX2 FanEQ Control
► AUX3 FanEQ Control
► AUX4 FanEQ Control
Press Enter
Press Enter
Press Enter
Press Enter
Press Enter
Press Enter
Item Help ►►
↓↑→←:Move Enter:Select +/-/PU/PD:Value
F10:Save ESC:Exit
Click <Enter> key to enter its submenu (CPU FanEQ Control):
µGuru Utility V1.00
ABIT EQ
CPU FanEQ Control
CPU FanEQ Control
Enabled
Item Help ►►►
-Reference Temperature
-Control Temperature High
-Control Temperature Low
-DC Fan Voltage High
-DC Fan Voltage Low
CPU Temperature
65°C/149°F
35°C/95°F
12.0 V
8.0 V
↓↑→←:Move Enter:Select +/-/PU/PD:Value
F10:Save ESC:Exit
CPU FanEQ Control
When set to [Enabled], these items control the CPU fan speed by the following setting
combinations.
-
Reference Temperature
This item selects the reference point for taking temperature among the available options of CPU,
SYS, and PWM Temperature, but there is only one “CPU Temperature” item to choose for the
“CPU FanEQ Control”.
AN9 32X
3-7
-
Control Temperature High/Low
These items set the high and low temperature limit that you want to do the fan speed control.
DC Fan Voltage High/Low
-
These items set the high and low voltage limit that you want to provide the fan with.
※ The value of high limit must be set above the one of low limit.
Click <ESC> key to exit this menu and move back to the main menu of “ABIT EQ”. Move the
down-arrow key to the next item (SYS FanEQ Control), and then click <Enter> key to enter its
submenu:
µGuru Utility V1.00
ABIT EQ
SYS FanEQ Control
SYS FanEQ Control
Enabled
Item Help ►►►
-Reference Temperature
-Control Temperature High
-Control Temperature Low
-DC Fan Voltage High
-DC Fan Voltage Low
System Temperature
40°C/104°F
30°C/86°F
12.0 V
8.0 V
↓↑→←:Move Enter:Select +/-/PU/PD:Value
F10:Save ESC:Exit
SYS FanEQ Control
When set to [Enabled], these items control the SYS fan speed by the following setting
combinations.
-
Reference Temperature
This item selects the reference point for taking temperature among the available options of CPU,
SYS, and PWM Temperature.
-
Control Temperature High/Low
These items set the high and low temperature limit that you want to do the fan speed control.
DC Fan Voltage High/Low
-
These items set the high and low voltage limit that you want to provide the fan with.
※ The value of high limit must be set above the one of low limit.
3-8
AN9 32X
Click <ESC> key to exit this menu and move back to the main menu of “ABIT EQ”. Move the
down-arrow key to the next item (AUX1 FanEQ Control ~ AUX4 FanEQ Control), and then click
<Enter> key to enter its submenu:
µGuru Utility V1.00
ABIT EQ
AUX1 FanEQ Control
AUX1 FanEQ Control
Enabled
Item Help ►►►
-Reference Temperature
-Control Temperature High
-Control Temperature Low
-DC Fan Voltage High
-DC Fan Voltage Low
System Temperature
40°C/104°F
30°C/86°F
12.0 V
8.0 V
↓↑→←:Move Enter:Select +/-/PU/PD:Value
F10:Save ESC:Exit
AUX1 FanEQ Control ~ AUX4 FanEQ Control
When set to [Enabled], these items control the AUX1~4 fan speed by the following setting
combinations.
-
Reference Temperature
This item selects the reference point for taking temperature among the available options of CPU,
SYS, and PWM Temperature.
-
Control Temperature High/Low
These items set the high and low temperature limit that you want to do the fan speed control.
DC Fan Voltage High/Low
-
These items set the high and low voltage limit that you want to provide the fan with.
※ The value of high limit must be set above the one of low limit.
AN9 32X
3-9
3.2 Standard CMOS Features
Phoenix – Award BIOS CMOS Setup Utility
Standard CMOS Features
Thu. May 25 2006
12 : 34 : 56
Date (mm:dd:yy)
Time (hh:mm:ss)
Item Help
► IDE Channel 1 Master
► IDE Channel 1 Slave
► IDE Channel 3 Master
► IDE Channel 4 Master
► IDE Channel 5 Master
► IDE Channel 6 Master
► IDE Channel 7 Master
► IDE Channel 8 Master
None
None
None
None
None
None
None
None
Drive A
Drive B
Floppy 3 Mode Support
Halt On
1.44M, 3.5 in.
None
Disabled
All, But keyboard
Base Memory
Extended Memory
Total Memory
640K
1046520K
1047552K
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Date (mm:dd:yy)
This item sets the date you specify (usually the current date) in the format of [Month], [Date],
and [Year].
Time (hh:mm:ss)
This item sets the time you specify (usually the current time) in the format of [Hour], [Minute],
and [Second].
3-10
AN9 32X
ꢀ
IDE Channel 1 Master/Slave, IDE Channel 3~8 Master:
Click <Enter> key to enter its submenu:
Phoenix – Award BIOS CMOS Setup Utility
IDE Channel 1 Master
Press Enter
IDE HDD Auto-Detection
Item Help
IDE Channel 1 Master
Access Mode
Auto
Auto
Capacity
0 MB
Cylinder
Head
Precomp
Landing Zone
Sector
0
0
0
0
0
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
IDE HDD Auto-Detection
This item allows you to detect the parameters of IDE drives by pressing <Enter> key. The
parameters will be shown on the screen automatically.
IDE Channel 1 Master/Slave, IDE Channel 3~8 Master
When set to [Auto], the BIOS will automatically check what kind of IDE drive you are using. If
you want to define your own drive by yourself, set it to [Manual] and make sure you fully
understand the meaning of the parameters. Please refer to the instruction manual provided by
the device’s manufacturer to get the setting right.
Access Mode
This item selects the mode to access your IDE devices. Leave this item at its default [Auto]
setting to detect the access mode of your HDD automatically.
Capacity
This item displays the approximate capacity of the disk drive. Usually the size is slightly greater
than the size of a formatted disk given by a disk-checking program.
Cylinder
This item configures the number of cylinders.
AN9 32X
3-11
Head
This item configures the number of read/write heads.
Precomp
This item displays the number of cylinders at which to change the write timing.
Landing Zone
This item displays the number of cylinders specified as the landing zone for the read/write
heads.
Sector
This item configures the number of sectors per track.
ꢀ
Back to Standard CMOS Features Setup Menu:
Drive A & Drive B
This item sets the type of floppy drives (usually only Drive A) installed.
Floppy 3 Mode Support
This item allows you to use “3 Mode Floppy Drive” in Japanese computer system by selecting
drive A, B, or both. Leave this item at its default [Disabled] setting if you are not using this
Japanese standard floppy drive.
Halt On
This item determines whether the system stops if an error is detected during system boot-up.
[All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error.
[No Errors]: The system-boot will not stop for any error detected.
[All, But Keyboard]: The system-boot will stop for all errors except a keyboard error.
[All, But Diskette]: The system-boot will stop for all errors except a diskette error.
[All, But Disk/Key]: The system-boot will stop for all errors except a diskette or keyboard
error.
Base Memory
This item displays the amount of base memory installed in the system. The value of the base
memory is typically 640K for system with 640K or more memory size installed on the
motherboard.
Extended Memory
This item displays the amount of extended memory detected during system boot-up.
Total Memory
This item displays the total memory available in the system.
3-12
AN9 32X
3.3 Advanced BIOS Features
Phoenix – Award BIOS CMOS Setup Utility
Advanced BIOS Features
Enabled
Press Enter
Floppy
Quick Power on Self Test
► Hard Disk Boot Priority
First Boot Device
Item Help
Second Boot Device
Third Boot Device
Boot Other Device
Boot Up Floppy Seek
Boot Up NumLock Status
Security Option
Hard Disk
CDROM
Enabled
Disabled
On
Setup
1.4
Enabled
MPS Version Ctrl For OS
Full Screen Logo Show
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Quick Power On Self Test
When set to [Enabled], this item speeds up the Power On Self Test (POST) after powering on
the system. The BIOS shorten or skip some check during the POST.
Hard Disk Boot Priority
This item selects the hard disks booting priority. By pressing <Enter> key, you can enter its
submenu where the hard disks detected can be selected for the booting sequence to boot up
system.
This item functions only when there is the option of [Hard Disk] in any one of the
First/Second/Third Boot Device items.
First Boot Device / Second Boot Device / Third Boot Device / Boot Other Device
Select the drive to boot first, second and third in the [First Boot Device], [Second Boot Device],
and [Third Boot Device] items respectively. The BIOS will boot the operating system according
to the sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot
from another device other than these three items.
Boot Up Floppy Seek
When the computer boots up, the BIOS detects if the system has a FDD or not. When this item
is set to Enabled, if the BIOS detects no floppy drive, it will display a floppy disk drive error
message. If this item is disabled, the BIOS will skip this test. The default setting is Disabled.
AN9 32X
3-13
Boot Up NumLock Status
This item determines the default state of the numeric keypad at system booting up.
[On]: The numeric keypad functions as number keys.
[Off]: The numeric keypad functions as arrow keys.
Security Option
This item determines when the system will prompt for password - every time the system boots
or only when it enters the BIOS setup.
[Setup]: The password is required only when accessing the BIOS Setup.
[System]: The password is required each time the computer boots up.
To disable security, select Set Password at main menu and then you will be asked to enter the
password. Do not type anything and just press the <Enter> key and it will disable security.
Once security is disabled, the system will boot and you can enter the BIOS setup menu freely.
※ Don’t forget your password. If you forget the password, you will have to open
the computer case and clear all information in the CMOS before you can start up
the system. But by doing this, you will have to reset all previously set options.
MPS Version Ctrl For OS
This item specifies which version of MPS (Multi-Processor Specification) this motherboard will
use. Leave this item at its default setting.
Full Screen LOGO Show
This item determines if the full screen logo is shown when booting.
3-14
AN9 32X
3.4 Advanced Chipset Features
Phoenix – Award BIOS CMOS Setup Utility
Advanced Chipset Features
K8<->NB HT Speed
K8<->NB HT Width
NB-->SB HT Speed
Auto
Auto
Auto
Auto
Item Help
NB<->SB HT Width
PCI Express bus(SB)
NB<->SB Reference clock
PCI Express bus(NB)
► DRAM Configuration
SSE/SSE2 Instructions
System BIOS Cacheable
NVIDIA GPU Ex
Hyperclk GPU
Auto
Hyperclk GPU
Press Enter
Enable
Enable
Disabled
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
K8<->NB HT Speed:
This item selects the LDT Bus Frequency between CPU and NB.
K8<->NB HT Width:
This item selects the LDT Bus Width between CPU and NB.
NB-->SB HT Speed:
This item selects NB to SB LDT Bus Frequency.
NB<->SB HT Width:
This item selects the LDT Bus Width between NB and SB.
PCI Express bus(SB)
This item adjusts the bus clock for “PCIEXP2” slot.
NB<->SB Reference clock
This item adjusts the bus clock between NB and SB.
PCI Express bus(NB)
This item adjusts the bus clock for “PCIEXP1” slot.
AN9 32X
3-15
DRAM Configuration:
Click <Enter> key to enter its submenu.
You may manually set the DRAM timing parameters through the following sub-items, or leave
them at their default settings according to the SPD (Serial Presence Detect) data stored in the
DRAM.
Phoenix – Award BIOS CMOS Setup Utility
DRAM Configuration
DRAM Timing Selectable
X - DRAM Clock
Auto
Item Help
DDR2 533
Skip DQS
Enabled
Channel
Disabled
2 Clocks
105 ns
75 ns
- DQS Timing Training
- CKE Base Power Down Mode
- CKE Base Power Down by
- Memclock Tri-Stating
X - TwTr Command Delay
X - Trfc0 for DIMM1
X - Trfc1 for DIMM2
X - Trfc2 for DIMM3
X - Trfc3 for DIMM4
75 ns
75 ns
X - Write Recovery Time(Twr)
X - Precharge Time(Trtp)
X - Row Cycle Time(Trc)
X - RAS2CAS R/W Delay(Trcd)
X - RAS to RAS Delay(Trrd)
X - Row Precharge Time(Trp)
X - Min. RAS Act-Time(Tras)
Memory Hole Remapping
DRAM ECC Enable
4 Clocks
2 Clocks
17 Clocks
4 Clocks
2 Clocks
4 Clocks
12 Clocks
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
F0
X - DRAM MCE Enable
X - Chip-Kill Mode Enable
X - DRAM ECC Redirection
X - DRAM Scrub Rate
X - L2 Cache Scrub Rate
X - DCache Scrub Rate
Auto Optimize Bottom IO
X - [31:24] IO Space
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
ꢀ
Back to Advanced Chipset Features Setup Menu:
SSE/SSE2 Instructions
This item allows you to Enable or Disable the SSE/SSE2 (Streaming SIMD Extensions)
instruction set.
System BIOS Cacheable
This item enables or disables caching the system BIOS for faster execution.
NVIDIA GPU Ex
Stands for “GPU Extra Performance”. Enable this item to work for certain NVIDIA SLI graphics
cards with certain driver version, but only minor performance will be expected. Leave this item
at its default setting (Disabled).
3-16
AN9 32X
3.5 Integrated Peripherals
Phoenix – Award BIOS CMOS Setup Utility
Integrated Peripherals
► OnChip IDE/RAID Function
Init Display First
OnChip USB
Press Enter
PCIEXP1
V1.1+V2.0
OS
OS
Auto
Auto
Auto
Disabled
Enabled
Enabled
IDE
Item Help
- USB Keyboard Support
- USB Mouse Support
OnChip Audio Controller
OnChip LAN1 Controller
OnChip LAN2 Controller
Onboard LAN Boot ROM
Onboard FDD Controller
Onboard SATA Controller
- Onboard SATA Mode
- SATA Option ROM
Enabled
Enabled
Onboard 1394 Controler
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
ꢀ
OnChip IDE/RAID Function
Click <Enter> key to enter its submenu:
Phoenix – Award BIOS CMOS Setup Utility
OnChip IDE/RAID Function
Press Enter
Press Enter
► IDE Function Setup
► RAID Configuration
Item Help
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
AN9 32X
3-17
ꢀ
IDE Function Setup:
Click <Enter> key to enter its submenu:
Phoenix – Award BIOS CMOS Setup Utility
IDE Function Setup
Enabled
Enabled
IDE 1 Controller
Item Help
IDE DMA transfer access
IDE HDD Block Mode
Serial-ATA Controller
Enabled
All Enabled
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
IDE 1 Controller
This item allows you to enable or disable the IDE1 controller.
IDE DMA transfer access:
This item selects the DMA mode for devices connected through IDE channels.
IDE HDD Block Mode
This item enables or disables the IDE HDD Block Mode.
Serial-ATA Controller
This item enables or disables the on-chip SATA controller.
3-18
AN9 32X
ꢀ
RAID Configuration:
Click <Enter> key to enter its submenu:
Phoenix – Award BIOS CMOS Setup Utility
RAID Configuration
Disabled
Disabled
RAID Function
Item Help
X - Serial-ATA 1 RAID
X - Serial-ATA 2 RAID
X - Serial-ATA 3 RAID
X - Serial-ATA 4 RAID
X - Serial-ATA 5 RAID
X - Serial-ATA 6 RAID
X - OnChip SATA Boot ROM
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
RAID Function
This item allows you to enable or disable the RAID function for Serial-ATA 1~6 ports.
-
Serial-ATA 1 RAID ~ Serial-ATA 6 RAID
This item allows you to enable or disable the RAID function for each of the Serial-ATA 1~6 port
individually.
-
OnChip SATA Boot ROM
This item allows you to use the boot ROM of OnChip SATA to boot up system.
ꢀ
Back to Integrated Peripherals Setup Menu:
Init Display First
This item selects which display slot to initialize first when the system boots.
OnChip USB
Select the type of USB controller. Three options are available: Disabled ꢀ V1.1+V2.0 ꢀ V1.1.
The default setting is V1.1+V2.0. If you choose to disable this item, the “USB Keyboard
Support” and “USB Mouse Support” items will not be available to select in Integrated
Peripherals menu.
AN9 32X
3-19
-
USB Keyboard Support
Select [BIOS] for the legacy operating system (such as DOS) that does not support USB
keyboard.
-
USB Mouse Support
Select [BIOS] for the legacy operating system (such as DOS) that does not support USB
mouse.
OnChip Audio Controller
This option enables or disables the audio controller.
OnChip LAN1 Controller
This option enables or disables the LAN1 controller.
OnChip LAN2 Controller
This option enables or disables the LAN2 controller.
Onboard LAN Boot ROM
This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and
access the local area network directly.
Onboard FDD Controller
Two options are available: Enabled and Disabled. The default setting is Enabled. You can
enable or disable the onboard FDD controller.
Onboard SATA Controller
This item enables or disables the Onboard SATA controller.
-
Onboard SATA Mode
This item determines the mode for Onboard Serial ATA.
[IDE]: The on-chip Serial ATA served as IDE mode.
[RAID]: The on-chip Serial ATA served as RAID mode.
-
SATA Option ROM
This item allows you to use the boot ROM of onboard Serial ATA RAID to boot up system.
Onboard 1394 Controller:
This option enables or disables the IEEE 1394 controller.
3-20
AN9 32X
3.6 Power Management Setup
Phoenix – Award BIOS CMOS Setup Utility
Power Management Setup
S3(Suspend-To-RAM)
Disabled
ACPI Suspend Type
Item Help
- USB Resume from S3
Power Button Function
Wakeup by PME# of PCI
Wakeup by OnChip LAN
Wakeup by Alarm
Instant-Off
Enabled
Enabled
Disabled
X - Day (of Month) Alarm
X - Time (hh:mm:ss) Alarm
Cool’n’Quiet Technology
Power On Function
X - KB Power On Password
X - Hot Key Power On
Restore on AC Power Loss
0
0: 0 : 0
Auto
Button Only
Enter
Ctrl-F1
Power Off
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
ACPI Suspend Type
This item selects the type of Suspend mode.
[S1(PowerOn-Suspend)]: Enables the Power On Suspend function.
[S3(Suspend-To-RAM)]: Enables the Suspend to RAM function.
-
USB Resume from S3
When set to [Enabled], this item allows you to use a USB device to wake up a system that is in
the S3 (STR - Suspend To RAM) state. This item can be configured only if the item “ACPI
Suspend Type” is set to [S3(STR)].
Power Button Function
This item selects the method of powering off your system:
[Delay 4 Sec.]: Pushing the power button for more than 4 seconds will power off the system.
This will prevent the system from powering off in case you accidentally hit or pushed the power
button.
[Instant-Off]: Pressing and then releasing the power button at once will immediately power
off the system.
Wakeup by PME# of PCI
When set to [Enabled], access through the add-on PCI card can remotely wake up the system
that was in Soft-Off condition. The PCI card must support the wake up function.
AN9 32X
3-21
Wakeup by OnChip LAN
When set to [Enabled], you can remotely wake up a PC in Soft-Off condition via a LAN card that
support the wake up function.
Wakeup by Alarm
When set to [Enabled], you can set the date and time you would like the Soft-Off PC to
power-on in the “Date (of Month) Alarm” and “Time (hh:mm:ss) Alarm” items. However,
if the system is being accessed by incoming calls or the network (Resume On Ring/LAN) prior to
the date and time set in these items, the system will give priority to the incoming calls or
network instead.
-
Date (of Month) Alarm
[0]: This option power-on the system everyday according to the time set in the “Time
(hh:mm:ss) Alarm” item.
[1-31]: This option selects a date you would like the system to power-on. The system will
power-on on the date set, and the time set in the “Time (hh:mm:ss) Alarm” item.
-
Time (hh:mm:ss) Alarm
This item sets the time you would like the system to power-on.
Cool ’n’ Quiet Technology:
This option enables or disables the AMD K8 cool and quiet function.
Power On Function
This item selects the way you want your system to power on.
[Password]: Use a password to power on the system, select this option then press <Enter>.
Enter your password. You can enter up to 5 characters. Type in exactly the same password to
confirm, and then press <Enter>.
[Hot KEY]: Use any of the function keys between <F1> to <F12> to power on the system.
[Mouse Left]: Double click the mouse left button to power on the system.
[Mouse Right]: Double click the mouse right button to power on the system.
[Any KEY]: Use any keyboard keys to power on the system.
[Button Only]: Use only the power button to power on the system.
[Keyboard 98]: Use the power-on button on the “Keyboard 98” compatible keyboard to power
on the system.
※ To enable this “Power On” function, the wake-up header of [USB-PWR1] and
[USB-PWR2] must be set to [Enabled] position. Please refer to the configuration
of “Wake-up Header” [USB-PWR1] and [USB-PWR2] in section 2.3.2, chapter 2.
※ The mouse wake up function can only be used with the PS/2 mouse, not with
the COM port or USB type. Some PS/2 mice cannot wake up the system because
of compatible problems. If the specs of your keyboard are too old, it may fail to
power on.
3-22
AN9 32X
-
KB Power ON Password
This item sets the password required in order to power on your computer.
※ Do not forget your password, or you will have to clear the CMOS and reset all
parameters in order to utilize this function again.
-
Hot Key Power ON
This item powers on the system by pressing <Ctrl> key plus one of each function key (<F1> ~
<F12>) simultaneously.
Restore on AC Power Loss
This item selects the system action after an AC power failure.
[Power Off]: When power returns after an AC power failure, the system’s power remains off.
You must press the Power button to power-on the system.
[Power On]: When power returns after an AC power failure, the system’s power will be
powered on automatically.
[Last State]: When power returns after an AC power failure, the system will return to the
state where you left off before power failure occurs. If the system’s power is off when AC
power failure occurs, it will remain off when power returns. If the system’s power is on when
AC power failure occurs, the system will power-on when power returns.
AN9 32X
3-23
3.7 PnP/PCI Configurations
Phoenix – Award BIOS CMOS Setup Utility
PnP/PCI Configurations
Auto(ESCD)
Press Enter
Resources Controlled By
X - IRQ Resources
Item Help
PCI/VGA Pallete Snoop
Disbaled
** PCI Express relative items **
Maximum Payload Size 4096
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Resources Controlled By
This item configures all of the boot and Plug-and-Play compatible devices.
[Auto(ESCD)]: The system will automatically detect the settings.
[Manual]: Choose the specific IRQ resources in the “IRQ Resources” menu.
3-24
AN9 32X
-
IRQ Resources
Click <Enter> key to enter its submenu:
This item sets each system interrupt to either [PCI Device] or [Reserved].
Phoenix – Award BIOS CMOS Setup Utility
- IRQ Resources
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
Reserved
Item Help
PCI Device
PCI Device
PCI Device
PCI Device
↓↑→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:GeneralHelp
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
ꢀ
Back to PnP/PCI Configurations Setup Menu:
PCI/VGA Palette Snoop
This item determines whether the MPEG ISA/VESA VGA cards can work with PCI/VGA or not.
[Disabled]: MPEG ISA/VESA VGA cards do not work with PCI/VGA.
[Enabled]: MPEG ISA/VESA VGA cards work with PCI/VGA.
Maximum Payload Size
This item sets the maximum TLP payload size for the PCI Express devices.
AN9 32X
3-25
3.8 Load Fail-Safe Defaults
This option loads the BIOS default values for the most stable, minimal-performance system
operations.
3.9 Load Optimized Defaults
This option loads the BIOS default values that are factory settings for optimal-performance
system operations.
3.10 Set Password
This option protects the BIOS configuration or restricts access to the computer itself.
3.11 Save & Exit Setup
This option saves your selections and exits the BIOS setup menu.
3.12 Exit Without Saving
This option exits the BIOS setup menu without saving any changes.
3-26
AN9 32X
4. Driver & Utility CD
The “Driver & Utility CD” that came packed with this motherboard contains drivers, utilities and
software applications required for its basic and advanced features.
Place the “Driver & Utility CD” into the CD-ROM drive in your system. The following installation
auto-run screen appears. If not, browse the root directory of the CD-ROM via the File Manager,
and double click the “AUTORUN” file.
•
•
•
•
[Drivers]: Click to enter the driver installation menu.
[Manual]: Click to enter the user’s manual menu.
[Utility]: Click to enter the utilities installation menu.
[ABIT Utility]: Click on this tab to enter the menu for installing utilities exclusively
developed by ABIT.
•
•
[
[
Browse CD]: Click to browse the contents of this “Driver & Utility CD”.
Close]: Click to exit this installation menu.
AN9 32X
4-1
4.1 nVidia nForce Chipset Driver
To install this driver:
1.
2.
Click on the [Drivers] tab in the installation menu screen.
Click the [nVidia nForce Chipset Driver]. The following screen appears:
3.
4.
Follow the prompts on the screen to complete installation.
Restart the system for the driver to take effect.
※ Please install this nVidia nForce Chipset Driver first after having installed the
Windows operating system.
4-2
AN9 32X
4.2 Realtek HD Audio Driver
To install this driver:
1.
2.
Click on the [Drivers] tab in the installation menu screen.
Click the [Realtek HD Audio Driver] item. The following screen appears:
3.
4.
Follow the prompts on the screen to complete installation.
Restart the system for the driver to take effect.
※ Install this Driver after having installed the “AudioMAX” daughter-card.
AN9 32X
4-3
4.3 Silicon Image 3132 RAID Driver
To install this driver:
1.
2.
Click on the [Drivers] tab in the installation menu screen.
Click the [Silicon Image 3132 RAID Driver] item. The following screen appears:
3.
4.
Follow the prompts on the screen to complete installation.
Restart the system for the driver to take effect.
4-4
AN9 32X
4.4 Cool’n’Quiet Driver
To install this driver:
1.
2.
Click on the [Drivers] tab in the installation menu screen.
Click the [Cool’n’Quiet Driver] item. The following screen appears:
3.
4.
Follow the prompts on the screen to complete installation.
Restart the system for the driver to take effect.
AN9 32X
4-5
5.
After the system restarted, open the “Power Options” from the control panel and choose
the power scheme “Minimal Power Management” to enable Cool ‘n’ Quiet.
※ For Windows 2000 or ME system, an AMD Cool ‘n’ Quiet tab will appear under
“Power Options” when the Cool ‘n’ Quiet software for Windows 2000 and ME is
installed. This must be set to “Automatic Mode” for Cool ‘n’ Quiet to be enabled.
4-6
AN9 32X
4.5 USB 2.0 Driver
※ There is no need to install this driver for Windows 2000 with Service Pack 4,
Windows XP with Service Pack 1, or their later version.
4.6 ABIT µGuru Utility
The µGuru Utility combined with the optional Guru Clock allows you to access and select system
performance of your system while playing games, listening music, browsing Internet or office
applications in full screen with no need to stop or close the running application.
To install this utility:
1.
2.
Click on the [ABIT Utility] tab in the installation menu screen.
Click the [ABIT Guru] item. The following screen appears:
3.
4.
Follow the prompts on the screen to complete installation.
Restart the system for the driver to take effect.
AN9 32X
4-7
4.7 NVRaid Floppy Disk
If you lost or damaged the SATA Driver Disk that came with the package, use the NVRaid
Floppy Disk to create another one.
To install this utility:
1.
2.
Click on the [ABIT Utility] tab in the installation menu screen.
Click the [Generate NVRaid Floppy Disk[32bit]]. The following screen appears:
Insert one blank floppy disk to the selected floppy drive and click [Build].
Click [OK] to finish building the SATA Driver Disk.
3.
※ If you are using a windows 2000 operating system, please update your system
to Service Pack 4 before starting to setup the NVIDIA RAID.
4-8
AN9 32X
5. Appendix
5.1 POST Code Definitions
5.1.1 AWARD POST Code Definitions
POST
Description
(hex)
CF
Test CMOS R/W functionality
Early chipset initialization:
-Disable shadow RAM
C0
-Disable L2 cache (socket 7 or below)
-Program basic chipset registers
Detect memory
C1
-Auto-detection of DRAM size, type and ECC
-Auto-detection of L2 cache (socket 7 or below)
Expand compressed BIOS code to DRAM
Call chipset hook to copy BIOS back to E000 & F000 shadow RAM
Expand the Xgroup codes locating in physical address 1000:0
Initial Superio_Early_Init switch
C3
C5
01
03
1. Blank out screen
05
07
08
2. Clear CMOS error flag
1. Clear 8042 interface
2. Initialize 8042 self-test
1. Test special keyboard controller for Winbond 977 series Super I/O chips
2. Enable keyboard interface
1. Disable PS/2 mouse interface (optional)
2. Auto detect ports for keyboard & mouse followed by a port & interface swap (optional)
3. Reset keyboard for Winbond 977 series Super I/O chips
0A
Test F000h segment shadow to see whether it is R/W-able or not. If test fails, keep beeping
the speaker
0E
10
12
14
Auto detect flash type to load appropriate flash R/W codes into the run time area in F000 for
ESCD & DMI support
Use walking 1’s algorithm to check out interface in CMOS circuitry. Also set real-time clock
power status, and then check for override
Program chipset default values into chipset. Chipset default values are MODBINable by
OEM customers
Initial onboard clock generator if Early_Init_Onboard_Generator is defined. See also POST
26.
16
18
1B
Detect CPU information including brand, SMI type (Cyrix or Intel) and CPU level (586 or 686)
Initial interrupts vector table. If no special specified, all H/W interrupts are directed to
SPURIOUS_INT_HDLR & S/W interrupts to SPURIOUS_soft_HDLR.
1D
1F
21
Initial EARLY_PM_INIT switch
Load keyboard matrix (notebook platform)
HPM initialization (notebook platform)
1. Check validity of RTC value: e.g. a value of 5Ah is an invalid value for RTC minute.
2. Load CMOS settings into BIOS stack. If CMOS checksum fails, use default value instead.
23
24
Prepare BIOS resource map for PCI & PnP use. If ESCD is valid, take into consideration of
the ESCD’s legacy information.
AN9 32X
5-1
Early PCI Initialization:
-Enumerate PCI bus number.
25
-Assign memory & I/O resource
-Search for a valid VGA device & VGA BIOS, and put it into C000:0
1. If Early_Init_Onboard_Generator is not defined Onboard clock generator initialization.
Disable respective clock resource to empty PCI & DIMM slots.
2. Init onboard PWM
26
27
29
3. Init onboard H/W monitor devices
Initialize INT 09 buffer
1. Program CPU internal MTRR (P6 & PII) for 0-640K memory address.
2. Initialize the APIC for Pentium class CPU.
3. Program early chipset according to CMOS setup. Example: onboard IDE controller.
4. Measure CPU speed.
2B
2D
Invoke Video BIOS
1. Initialize double-byte language font (Optional)
2. Put information on screen display, including Award title, CPU type, CPU speed, full screen
logo.
Reset keyboard if Early_Reset_KB is defined e.g. Winbond 977 series Super I/O chips. See
also POST 63.
33
35
37
39
3C
3E
40
43
47
Test DMA Channel 0
Test DMA Channel 1.
Test DMA page registers.
Test 8254
Test 8259 interrupt mask bits for channel 1
Test 8259 interrupt mask bits for channel 2
Test 8259 functionality
Initialize EISA slot
1. Calculate total memory by testing the last double word of each 64K page
2. Program writes allocation for AMD K5 CPU
1. Program MTRR of M1 CPU
49
2. Initialize L2 cache for P6 class CPU & program CPU with proper cacheable range
3. Initialize the APIC for P6 class CPU
4E
4. On MP platform, adjust the cacheable range to smaller one in case the cacheable ranges
between each CPU are not identical
50
52
53
55
Initialize USB
Test all memory (clear all extended memory to 0)
Clear password according to H/W jumper (Optional)
Display number of processors (multi-processor platform)
Display PnP logo
57
Early ISA PnP initialization
-Assign CSN to every ISA PnP device
59
5B
Initialize the combined Trend Anti-Virus code
(Optional Feature) Show message for entering AWDFLASH.EXE from FDD (optional)
1. Initialize Init_Onboard_Super_IO
5D
60
2. Initialize Init_Onbaord_AUDIO
Okay to enter Setup utility; i.e. not until this POST stage can users enter the CMOS setup
utility
63
65
67
69
Reset keyboard if Early_Reset_KB is not defined
Initialize PS/2 Mouse
Prepare memory size information for function call: INT 15h ax=E820h
Turn on L2 cache
5-2
AN9 32X
6B
6D
Program chipset registers according to items described in Setup & Auto-configuration table
1. Assign resources to all ISA PnP devices
2. Auto assign ports to onboard COM ports if the corresponding item in Setup is set to
“AUTO”
1. Initialize floppy controller
6F
75
2. Set up floppy related fields in 40:hardware
Detect & install all IDE devices: HDD, LS120, ZIP, CDROM …
(Optional Feature)
Enter AWDFLASH.EXE if:
76
-AWDFLASH is found in floppy drive
-ALT+F2 is pressed
77
7A
7C
Detect serial ports & parallel ports.
Detect & install co-processor
Init HDD write protect
Switch back to text mode if full screen logo is supported
-If errors occur, report errors & wait for keys
-If no errors occur or F1 key is pressed to continue: Clear EPA or customization logo
7F
E8POST.ASM starts
1. Call chipset power management hook
2. Recover the text font used by EPA logo (not for full screen logo)
3. If password is set, ask for password
Save all data in stack back to CMOS
Initialize ISA PnP boot devices
82
83
84
1. USB final Initialization
85
87
89
2. Switch screen back to text mode
NET PC: Build SYSID Structure
1. Assign IRQs to PCI devices
2. Set up ACPI table at top of the memory.
1. Invoke all ISA adapter ROMs
2. Invoke all PCI ROMs (except VGA)
1. Enable/Disable Parity Check according to CMOS setup
2. APM Initialization
8B
8D
8F
93
Clear noise of IRQs
Read HDD boot sector information for Trend Anti-Virus code
1. Enable L2 cache
2. Program Daylight Saving
3. Program boot up speed
4. Chipset final initialization.
94
5. Power management final initialization
6. Clear screen & display summary table
7. Program K6 write allocation
8. Program P6 class write combining
Update keyboard LED & typematic rate
1. Build MP table
95
96
FF
2. Build & update ESCD
3. Set CMOS century to 20h or 19h
4. Load CMOS time into DOS timer tick
5. Build MSIRQ routing table
Boot attempt (INT 19h)
AN9 32X
5-3
5.1.2 AC2005 POST Code Definitions
POST
Description
(hex)
Power On Sequence
Start power on sequence
8.1.
8.2.
8.3.
8.4.
8.5.
8.6.
8.7.
8.8.
8.9.
8.A.
8.B.
8.C.
8.D.
8.D.
8.E.
8.F.
Enable ATX power supply
ATX power supply ready
DDR voltage ready
Setup PWM for CPU core voltage
Assert PWM for CPU core voltage
Check CPU core voltage
CPU core voltage ready
Initial clock generator IC
North Bridge chipset voltage ready
AGP voltage ready
3VDUAL voltage ready
VDDA 2.5V voltage ready
GMCHVTT voltage ready
Check CPU fan speed
Assert all power ready
Complete µGuru initial process
AWARD BIOS take over booting job
9.0.
Power Off Sequence
9.1.
9.2.
9.3.
9.4.
9.5.
9.6.
9.7.
9.8.
9.9.
Start power off sequence
De-Assert all power
De-Assert power on
De-Assert LDT Bus power
De-Assert PWM for CPU core voltage
De-Assert CPU core voltage
Check CPU core voltage
De-Assert ATX power supply
Complete power off sequence
Others
F.0.
F.1.
F.2.
F.3.
Button reset
SoftMenu reset
Power on sequence timeout
Power off sequence timeout
5-4
AN9 32X
5.2 Troubleshooting (How to Get Technical Support?)
5.2.1 Q & A
Q: Do I need to clear the CMOS before I use a new motherboard to assemble my
new computer system?
A: Yes, we highly recommend that you clear the CMOS before installing a new motherboard.
Please move the CMOS jumper from its default 1-2 position to 2-3 for a few seconds, and
then back. When you boot up your system for the first time, follow the instructions in the
user's manual to load the optimized defaults.
Q: If my system hangs when I update the BIOS or set the wrong CPU parameters,
what should I do?
A: Whenever you update the BIOS or if the system hangs due to wrong CPU parameters
setting, always clear CMOS jumper before booting up again.
Q: Why does the system fail to boot up again right after a mechanical power-off?
A: Please keep a 30-second interval between each mechanical power On/Off.
Q: Why does the system fail to boot up and nothing displays on the screen after I
did some over-clocking or non-standard settings inside the BIOS?
A: It should not cause hardware or permanent damage to motherboard when BIOS settings
were changed from default to over-clocking or non-standard status.
We suggest the following three troubleshooting methods to discharge CMOS data, recover
the hardware default status, and then making the motherboard work again. There is no
need to bother returning the motherboard to where you bought it from or go through an
RMA process.
Step 1.Switch off the power supply unit and then switch it on again after one minute. If
there is no power-switch on the power supply unit, disconnect its power cord for
one minute and then reconnect.
Press and hold the <Insert> key on the keyboard, and press the power-on button
to boot up system. If it works, release the <Insert> key and hit <Del> key to enter
the BIOS setup page to apply the correct settings.
If the situation remains the same, repeat the procedures in Step 1 for three times,
or try Step 2.
Step 2.Switch off the power supply unit or disconnect the power cord. Open the chassis
cover. Locate the CCMOS jumper near the button battery. Change the jumper
position from default 1-2 to 2-3 for one minute to discharge the CMOS data, and
then put it back to default 1-2 position.
Close the chassis and switch on the power supply unit or plug in the power cord.
Press the power-on button to boot up system. If it works, hit <Del> key to enter
the BIOS setup page to do the correct settings.
If the situation remains the same, try Step 3.
Step 3.The same procedure as Step 2, but while discharging the CMOS data, pull out the
ATX power connectors from motherboard and remove the button battery during
CMOS discharge.
AN9 32X
5-5
Q: How to get a quick response for my request on technical support?
A: Please carry out a simple troubleshooting before sending “Technical Support Form”:
System boot-up fails after the system had been assembled:
Check the motherboard’s supporting specifications first to see if all the key components
attached in your system can meet.
To do so, you may:
ꢀ
Remove all the unnecessary add-on devices (except the CPU, VGA card, DRAM, and
Power Supply), and then reboot.
ꢀ
If the trouble still exists, try another VGA card of different brand/model to see if the
system will start.
ꢀ
ꢀ
If the trouble still exists, try another memory module of different brand/model.
If the trouble still exists, try another CPU and Power Supply.
If the system runs successfully, shut it down and start re-installing the interface cards and
devices that were previously installed in the system. Re-install and start the system one at a
time until the system won’t start.
Malfunction in the OS:
If the system hangs after resuming from S3 or some testing program, if the CPU cannot be
recognized properly, if the display resolution mixed, or if a certain program cannot be
executed, etc, you may:
ꢀ
ꢀ
ꢀ
Upgrade the motherboard’s latest BIOS version.
Upgrade the add-on device’s latest driver version.
Check if there is any conflict in the “Control Panel/System Properties”.
Q: How to fill in the “Technical Support Form”?
A: To fill in this “Technical Support Form”, please refer to the following instructions:
•
•
•
•
•
Region: Type in your country name.
E-mail: Type in your contact E-mail information.
First name: Type in your first name.
Last name: Type in your last name.
Subject: Type in the model name and the problem of your motherboard.
Example 1: AA8XE and SCSI 29160 malfunction
Example 2: AA8XE boot fails, POST code AF
Example 3: AA8XE (system hang when S3 resume)
•
•
•
Motherboard: Type in the model name and revision number of your motherboard.
Example: AA8XE REV: 1.00
BIOS Version: Type in the BIOS version of your motherboard. (You can find it on the
screen during the POST sequence.)
CPU: Type in the brand name and the speed (MHz) of your CPU. (Illustrate the
over-clocking status if you had done so.)
Example: Intel 650 3.4GHz (OC FSB=220MHz)
•
Memory brand: Type in the brand and model name of your memory module.
Example: Memory brand: Kingston (KVR533D2N4/1G)
5-6
AN9 32X
•
•
Memory size: Type in the size of your memory module.
Example: 512M* 4PCS
Memory configuration: Type in the memory configuration in BIOS setting.
Example: Memory Timing: 2.5-3-3-7 @533MHz
•
•
Graphics information: Note Graphics card’s brand, model and driver version
Graphics card: Type in the brand and model name of your graphics card.
Example: ATI RADEON X850 XT PE
•
Graphics driver version: Type in the driver version of your graphics card
Example: Catalyst 5.12V
•
•
•
Power supply maker: Type in the brand and model name of your power supply unit.
Power supply wattage: Type in the power wattage of your power supply unit.
Storage devices: Type in the brand and specifications of your HDD drive and quantity.
Specify if it was inserted on IDE (Master or Slave) or SATA ports, including the RAID
allocation status.
Example 1: WD Caviar WD600 60GB (on IDE2 master), Maxtor DiamondMax 10 SATA
300GB (on SATA 3)
Example 2: Maxtor DiamondMax 10 SATA 300GB *2 (on SATA 3, SATA 4 RAID 1)
•
•
Optical devices: Type in the brand and specifications of your optical drives and
quantity. Specify if it was inserted on IDE (Master or Slave) or SATA ports.
Other devices: Indicate which add-on cards or USB devices that you absolutely sure
are related to the problem. If you cannot identify the problem’s origin, indicate all the
add-on cards or USB devices inserted on your system.
Example: AHA 29160 (on PCI 2), Sandisk Cruzer mini 256MB USB Flash-disk.
•
•
Operating system: Indicate which OS and language version
Example: Microsoft Windows XP SP2, English version
Example: Microsoft Media Center Edition 2005, Korean version
Problem description: Describe the problem of your system configuration. Indicate
the steps to duplicate problem if possible.
See the next page for a blank Technical Support Form, or visit our website to fill in the
Q. Is the motherboard dead? Do I need to return it to where I bought from or go
through an RMA process?
A: After you had gone through the troubleshooting procedures, yet the problem still exists, or
you find an evident damage on the motherboard. Please contact our RMA center.
AN9 32X
5-7
5.2.2 Technical Support Form
Country:
First name:
Last Name:
Subject:
Motherboard:
BIOS Version:
CPU:
Memory brand:
Memory size:
Memory configuration:
Graphics card:
Graphics driver version:
Power supply maker:
Power supply wattage:
Storage devices:
Optical devices:
Other devices:
Operating system:
Problem description:
5-8
AN9 32X
5.2.3 UNIVERSAL ABIT Contact Information
Taiwan Head Office
UNIVERSAL ABIT Co. Ltd.
No. 323, Yang Guang St., Neihu, Taipei, 114, Taiwan
Tel: 886-2-8751-8888
Fax: 886-2-8751-3382
North America, South America
ABIT Computer (U.S.A.) Corporation
2901 Bayview Drive, Fremont, CA 94538, U.S.A.
Tel: 1-510-623-0500
Fax: 1-510-623-1092
Website: http://www.abit-usa.com
RMA Center: http://rma.abit-usa.com
U.K., Ireland
ABIT Computer (U.K.) Corporation Ltd.
Unit 3, 24-26 Boulton Road, Stevenage, Herts SG1 4QX, U.K.
Tel: 44-1438-228888
Fax: 44-1438-226333
Austria, Czech, Romania, Bulgaria, Slovakia, Croatia, Bosnia, Serbia, Macedonia
Asguard Computer Ges.m.b.H
Schmalbachstrasse 5, A-2201 Gerasdorf / Wien, Austria
Tel: 43-1-7346709
Fax: 43-1-7346713
Germany and Benelux (Belgium, Netherlands, Luxembourg), France, Italy, Spain,
Portugal, Greece, Denmark, Norway, Sweden, Finland, Switzerland
AMOR Computer B.V. (ABIT's European Office)
Jan van Riebeeckweg 15, 5928LG, Venlo, The Netherlands
Tel: 31-77-3204428
Fax: 31-77-3204420
Shanghai
ABIT Computer (Shanghai) Co. Ltd.
Tel: 86-21-6235-1829
Fax: 86-21-6235-1832
Website: http://www.abit.com.cn
Poland
ABIT Computer (Poland) Co. Ltd.
Przedstawicielstwo w Polsce, ul. Wita Stwosza 28, 50-149 Wrocław
Tel: 48 71 780 78 65 (Technical support/RMA)
Tel: 48 71 718 19 70 (PR/Marketing)
Fax: 48 71 780 78 66
AN9 32X
5-9
|
