O W N E R ’ S &
OMPAERNATUORA’SL
❧
PRO - S E R I E S
C S V ’ S W I T H G A S E N G I N E S
CAUTION: OPERATE YOUR GAS ENGINE
OUTDOORS, IN A WELL-VENTILATED
AREA. KEEP CHILDREN AND PETS
AWAY FROM THIS POWER EQUIP-
MENT. SERIOUS INJURY OR DEATH
CAN RESULT.
KEY FEATURES
Patriot Chipper-Shredder-Vac
HOPPER GUARDS
(Do not reach beyond
the guards.)
!
▲
™
PUSH/PULL HANDLE
SHREDDER
HOPPER
DISCHARGE
CHUTE
WARNING: DO NOT OPERATE THIS
EQUIPMENT UNTIL IT IS COMPLETE-
LY ASSEMBLED AND SERVICED AND
YOU HAVE READ AND UNDERSTAND
THIS MANUAL. FILL OUT, SIGN AND
RETURN YOUR WARRANTY CARD
AND SATISFACTION SURVEY AFTER
YOUR INITIAL USE OF THE
PRODUCT.
!
▲
SPARK PLUG
CHIPPER CONE
INLET
WIRE
THROTTLE
WARNING: NEVER PUT YOUR HANDS,
FACE OR CLOTHING INTO ANY HOPPER,
CONE OR CHUTE WHEN THE ROTOR IS
TURNING. NEVER PUT YOUR FINGERS
OR FACE INTO THE CHUTE OR BEYOND
THE HOPPER GUARDS WHEN THE
ROTOR IS TURNING. ALWAYS HAVE
THE BAG ATTACHED BEFORE START-
ING. SERIOUS PERSONAL INJURY MAY
RESULT.
!
▲
AIR INTAKE
(Keep clean)
COLLECTION BAG
(Must be attached
before each use.)
OUTBOARD
BEARING
[No lubrication
needed.]
MODEL 10F-CSV
SHOWN HERE
DISCHARGE AREA.
Stay clear
during
operation.
ALWAYS ATTACH THE
BAG BEFORE START-
ING.
The area
marked by the
dotted line is the
SAFE
OPERATING AREA.
CUSTOMER SERVICE HOTLINE
WARNING: NEVER PUT YOUR HANDS,
FACE OR CLOTHING INTO THE CHIP-
PER CONE OR OTHER INLETS WHEN
THE ROTOR INSIDE IS STILL TURNING.
KEEP YOUR FINGERS AND FACE OUT
OF THE INLETS, OUTLETS AND
EXHAUSTS WHEN THE ROTOR IS
TURNING OR ENGINE IS RUNNING.
SERIOUS PERSONAL INJURY MAY
RESULT.
!
▲
1-800-798-CHIP
OUTSIDE THE U.S. CALL 1-262-523-4580
8:00 AM - 4:00 PM Central Standard Time
MONDAY - FRIDAY (EXCEPT MAJOR HOLIDAYS)
FAX 1-262-523-1011
What About Engine or Starting Problems?
The engine manufacturer warranties the engine separately. If you
experience difficulties with your engine, see your telephone book for
the engine manufacturer’s nearest service center.
How Do I File a Claim?
If you believe any Patriot product or part is defective within a three (3)
year period from the date of purchase, contact your place of purchase.
They will file your claim or they will direct you to a qualified Patriot
Authorized Service Center. You will be asked to produce a dated receipt
for the product if it was not registered with the factory.
If the product or part is determined to be defective by a Patriot
Authorized Service Center, we will repair or replace it at our discretion,
at no expense to you or the service center.
If the product or part is damaged due to negligence, abuse of the
product’s purpose, or improper maintenance, the warranty is void.
How Long Will It Take?
Warranty repairs may take a few minutes…or a few days. It depends on
the nature of the problem. We believe it is in everyone’s best interest to
provide service as quickly and efficiently as possible. However, during
peak seasons, a service center may need a week or more to schedule and
perform repairs.
What About Professional or Commercial Use?
A Patriot employed in any commercial endeavor (rental stores,
landscaping businesses, farming, etc.) is warranted for 90 days from
the date of purchase under the terms and conditions described above.
PRO-SERIES CSV Owner’s & Operator’s Manual,
80007-172-5P © 2002 Patriot Products, Inc.
All rights reserved. Illustrations by Robert F.
Schwengel. Patriot PRO-Series Chipper-Shredder-
Vac™ is a trademark of Patriot Products, Inc.,
registered in USA.
Common
(and Expensive)
Mistakes
CONTENTS
Sure-fire ways to shorten the life of
your chipper-shredder-vac while
incurring costly repairs along the
way:
❶ SAFETY
page 6
• Neglecting the engine’s need
for fresh, clean oil.
• Not cleaning the engine recoil
of debris or changing the air
filter from time to time.
Over-heating results, burning
out the engine.
• Chipping dead wood or
lumber and not sharpening
the knives more often.
• Forcing branches down the
chipper when the knives are
dull and not self-feeding.
• The occasional, if accidental,
railroad spike, brick, 2 x 4,
barbed wire, and/or gardening
tool “down the hatch” routine.
❷ ASSEMBLY
❸ OPERATION
❹ HOW IT WORKS
❺ MAINTENANCE
page 8
page 11
page 12
page 13
❻ WHAT TO DO WITH THE STUFF
NOW THAT IT’S ALL CHIPPED & SHREDDED
page 16
page 17
❼ ILLUSTRATED PARTS LIST
❽ TROUBLE-SHOOTER
back cover
ATTENTION: WEAR GOGGLES AND
STURDY SHOES WHEN USING THIS
MACHINE. HEARING PROTECTION IS
ALSO ADVISED.
!
▲
page 6
Message to Parents
Poor judgement when using this
equipment may result in damage
and serious personal injuries. Help
prevent accidents by making
thoughtful decisions about if, when,
and how older children will operate
this equipment.
❶ SAFETY
The Shut Down Procedure
Before assembling, using, servicing, or otherwise operating your chipper-
shredder-vac, protect everyone’s safety by knowing how and when to use the
Shut Down Procedure.
Age is not the only factor.
1. Size, strength, and coordina-
tion. Each is required to start, push,
pull, and turn the equipment safely.
2. Maturity and responsibility.
Does the young person think through
problems and use good judgement?
3. Supervision. Make time to
talk through the manual and walk
through the operation of the
machine. Supervise the operation
of the machine the first few times.
Do all re-fueling and maintenance
yourself.
HOW TO SHUT DOWN
1. Turn off the engine. Do not touch hot engine parts or exhaust.
2. Wait until the rotor has stopped turning.
3. Disconnect the spark plug wire from the spark plug.
WHEN TO SHUT DOWN
➪ Before attaching, unzipping, or detaching the collection bag.
➪ Before clearing debris from any inlet or outlet in the event of a clog.
➪ Before removing debris from inside the chipper cone or shredder hopper.
➪ Before refueling the gas tank or adding oil.
➪ Before putting hands, face, fingers, probes, etc., near moving parts.
➪ Before children, pets or bystanders come near.
Put safety first. Take time to
instruct the young person. Even as
they gain confidence and a sense of
accomplishment with the machine,
continue to monitor their work.
Your Responsibilities
Know how to stop the engine quickly.
▲ Show others who will use this product how to use it safely. Allowing
anyone—especially children—to use this equipment without instruction
may cause serious injury. Please remember that this is a tool, not a toy.
▲ Wear long pants, protective footwear, and safety goggles. Hearing
protection is advised. You may suffer injury if you work barefooted or
wear only sandals.
Long-Term Storage
Store the chipper-shredder-vac out of
reach of children and where gasoline
vapors will not find an open flame or
spark. For extended storage periods
(such as over the winter months),
add a fuel stabilizer and let the
engine run briefly to allow the stabi-
lizer to mix with the fuel and get into
the carburetor and fuel lines. Let the
engine to cool before storing.
▲ Keep alert while operating this equipment.
Operator and Property Hazards
Check all fasteners for tightness before each use. Keep the engine’s air intake
on top clear of debris and leaves. Do not move the machine while the engine
is running or the rotor is turning.
▲ Keep all guards, deflectors and warning labels in place. Replace them
Change the oil and add fresh fuel
to return the unit to “active duty.”
should they become cracked, broken or unreadable.
▲ Keep your face, hands, body, and clothing out of the hoppers, bag,
and discharge areas. Stay clear of moving parts and hot mufflers.
▲ Do not wear loose-fitting clothing or hanging jewelry.
Thrown Object Hazards
Clear the chipper and shredder hoppers before trying to start the engine.
▲ The collection bag must be installed by the operator before each use.
Do not start the engine until the bag is attached over the discharge chute.
▲ Do not use near pets, parked cars or bystanders.
▲ Inspect yard waste before processing. Make sure it is free of rocks,
glass, metal, and other non-organic objects.
WARNING: DO NOT OPERATE THIS
EQUIPMENT UNTIL (1) IT IS COM-
PLETELY ASSEMBLED AND SER-
VICED, AND (2) YOU READ AND
UNDERSTAND THIS MANUAL.
!
▲
▲ Work in daylight, so you can see objects, hazards, and bystanders.
page 7
Fire and Burn Hazards
Gasoline is very flammable. The vapor can explode. Use extreme care when
handling gasoline. KEEP FUEL AWAY FROM CHILDREN.
Use a proper fuel container for your gasoline. Do not remove the gas cap
until you have shut down the chipper-shredder-vac. Re-fuel the engine out of
doors and only after the engine has cooled down. Use a gasoline funnel.
Do not operate or store the chipper-shredder-vac, or the gasoline, near
open flames or other heat sources.
▲ Avoid touching a hot engine and exhaust system. Allow the engine to
cool before refueling, transporting, or storing the chipper-shredder-vac.
▲ Refuel in a well-ventilated area with the engine shut off and the rotor
fully stopped. Keep flames, sparks, and smoking materials away!
▲ Avoid spilling or over-filling the tank. Tighten the gas cap after re-
fueling. Allow spilled fuel to dry before re-starting the engine.
▲ Store the chipper-shredder-vac on a level surface in a well-ventilated
area, away from appliances like water heaters and clothes drier.
Safety & Maintenance
This chipper-shredder-vac is built to
meet or beat the very latest safety
standards established by the Outdoor
Power Equipment Institute and the
American National Standards
Institute.
Part of this certification requires
that safety labels meet certain
standards. They must be replaced
when they become worn out. It is
your responsibility to replace the
labels if they become hard to read.
Safety certification also requires
that all guards and deflectors be
kept in place and in good condition.
Again, it is the operator’s job to
repair or replace guards and deflec-
tors when necessary.
Grass and dry leaves are also flammable. Empty the bag when you are
finished, even if it is not full. Stored shreds and clippings are a fire hazard.
▲ Grass and dry leaves are flammable. Empty the bag before storage, even
if it is not full. Stored shreds and clippings are a fire hazard.
Carbon Monoxide Hazards
Exhaust from the engine contains poisonous carbon monoxide. It is colorless,
odorless, and can be lethal. Breathing the exhaust can cause loss of conscious-
ness, possibly leading to death.
Other Maintenance
▲ Do not operate any gas engine in an enclosed area. Use outdoors only!
▲ Carbon monoxide is a poison known to cause cancer and birth defects.
Regular maintenance must also
include the engine. Add oil as it is
needed and change the oil regularly.
Your engine manual has information
about the kind of oil to use, how
much to use, and how to add or
drain the oil.
Mechanical Hazards
If unusual vibration or noise occurs, shut down the chipper-shredder-vac.
Continuing to run the machine when it may be damaged may cause serious
property damage and personal injury. Replace or repair parts as needed and
check fasteners for tightness before resuming work. If there are still problems,
take it to a service shop.
It’s hard to say exactly when you
should sharpen the knives or replace
the shredding hammers.
Chipping branches and prunings
while they are green and fresh keeps
the knives wet and cool. They stay
sharp longer. Dead, dry wood—and
dirty, gravelly garden waste, for that
matter—dulls chipping knives.
Generally speaking, when the
knives do not pull branches down
the chipper with relative ease, it is
time to sharpen them. The hammers
can be checked after you have shut
down. If the edges are smooth,
weathered or bent, reverse or replace
them.
▲ Don’t tamper with the engine speed governors. They prevent rotating
parts from over-speeding and causing damage or injury. Seek an
authorized service mechanic should engine problems arise.
▲ Do not put your hands or any other part of your body or clothing inside
the cone, shredder hopper, or into any inlet or outlet to moving parts!
▲ Do not attempt even a minor clean-out of the cone, hopper, bag, or
engine service while the rotor is turning!
▲ Empty the collection bag when it is almost full to prevent clogging and
poor performance.
page 8
❷ ASSEMBLY
STEP 1
Put the leg into its holder. Insert the
lynch pin and clip the U-shaped
clasp over the front of the leg, onto
the end of the pin.
STEP 2
HEX HEAD CAP SCREW,
5/16-18 x 3.25”
The bag retaining bolt
used in Step 3.
Insert the base of the chipper casting,
bottom first, into the oval hole. Use
your 1/2” wrench to tighten three
serrated flange nuts (5/16-18) on the
exposed studs. Do not over-tighten
these nuts. Do not file or grind any part
of the chipper cone base.
SERRATED
FLANGE NUT
Side and top views.
The serrations on
the bottom bite into
the steel for better
staying power.
STEP 3
Thread one flange nut onto the 3-
1/4” long bolt with the serrated
side facing away from the head of the
bolt. Insert the end of the screw
through the hole under the discharge
chute. Screw on the remaining nut,
serrated side facing in this time.
Tighten with one 1/2” wrenches.
(Use two wrenches if the bolt won’t
go in easily.)
STEP 4
SEE YOUR ENGINE MANUAL FOR
PROPER OIL LEVELS. Oil and gas
are poured into different parts of the
engine. Do not mix the oil and the gas!
Engines are shipped with a reddish
lubricant in them. Please refer to
owners manual for proper oil type.
page 9
STEP 5
Attach the bag over the entire deflec-
tor shield assembly and the retaining
bolt you installed in STEP 3. Pinch
the plastic barrel clamp and pull
down sharply until the bag is tightly
attached. The bag must be put on
before each use of your chipper-
shredder-vac.
FIRE AND EMISSIONS
WARNINGS
(ESPECIALLY FOR CALIFORNIA
OWNERS AND OPERATORS)
!
▲
CAUTION: This engine may not be equipped
with a spark arrester. If it is to be used on
any forest-covered, brush-covered or
grass-covered unimproved land, a spark
arrester would have to be added to the
muffler before using the engine on such
land. The arrester must be maintained in
effective working order by the operator.
This is required by law in certain states.
Federal laws apply on federal lands.
Contact your authorized engine service
center in your telephone book for spark
arrester muffler options.
Now check all the fasteners. They may have loosened during shipping.
Tighten anything that’s loose. It’s a good idea to check the fasteners for tight-
ness before every use.
Don’t Have a Seizure
Bolt it together, add some gas and start chippin’...and the engine will seize and
jerk to a dead-stop in minutes.
Call the engine manufacturer and the first question will be, Was there oil in
the engine before you ran it? Because unless you put it there, there wasn’t.
Failure to fully prep the engine is the single most common mistake you
can make with power equipment. Young, old, weekend warrior, or seasoned
power jockey, it can happen to anyone. Slipping in a quart after the damage
is done doesn’t cover the tell-tale tracks, either.
KEEP A WIDE
STANCE AND
GENTLY PUSH
AND FOLD
So, read the engine manual, follow the instructions and hope you never
join the Seizure Club.
The good news is, people rarely join twice!
Also, it is important to keep the recoil area (where the pull cord is located)
clean of leaves and debris. Change the air filter regularly, too. If either of
these two intakes become too dusty and dirty, the engine overheats and may
seize up.
BUSHY DEBRIS
INTO THE CONE.
Engine Controls
Be careful before touching the muffler or other metal engine parts.
Even if the machine has been running just a few moments, the
engine and exhaust can get hot enough to cause a serious burn.
THE RABBIT
Low or Idle: When you are not shredding or chipping, move the
throttle to a lower speed.
Fast: When chipping, shredding or using the vac hose option,
move the throttle to its highest speed.
THE STOP SIGN
Move the throttle to OFF to cut power to the chipper-shredder-vac.
Notice, we do not say “to stop the chipper-shredder-vac.” Inertia
causes the rotor to coast, even after the power is shut off. Don’t
mess with a moving rotor!
page 10
ACCESSORY KIT
15-ft. Vac Kit Assembly (Optional)
The optional vacuum kit, 15 feet long and 4” in
diameter, is used to vacuum and grind leaves, pine
straw and other loose organic waste. The kit is sold
separately; instructions are provided here and with the
kit for your convenience.
FIRST
Insert two 1.25”-20 carriage bolts from inside the
nozzle and through the holes in the handle. Fasten
with the two 1/4”-20 serrated flange nuts provided
using a 7/16” wrench.
SECOND
Push one end of the hose firmly into the nozzle. The
nozzle has what is called a “regressive” fit. Turn the
nozzle a few times to adjust the angle of the nozzle.
THIRD*
Thread the other end of the hose into the adaptor
about three inches. You may need to tug it through
from the other side.
FOURTH*
When you want to use the vac, snap the adaptor into
the hopper before you turn on the engine. The adaptor
only fits with the DANGER decal on your right as you
stand behind the machine.
FIFTH & LAST*
Snap the cone cover over the chipper cone. This seals
off all air flow for maximum vacuuming power.
*Patented design featured in this step.
page 11
CAUTION: OPERATE YOUR GAS ENGINE
❸ OPERATION
!
OUTDOORS, IN A WELL-VENTILATED
AREA. KEEP CHILDREN AND PETS
AWAY FROM ANY OPERATING POWER
EQUIPMENT.
▲
Safe Operating Conditions
Avoid wet, slippery terrains or areas congested with people and traffic.
Avoid using the machine on driveways, sidewalks, gravel, and other hard
areas. The force of the air might make debris bounce up and hit cars,
you, or bystanders. Wear goggles and other protective clothing.
Chipping
POUR, RATHER
THAN DUMP, LOOSE
WASTE INTO THE
SHREDDER
CHIPPER
HP
CAPACITY
3” dia.
TYPE OF DISCHARGE
Coin-sized chips
Hard or soft branches, 9 & 10
prunings, corn stalks,
drier viney materials,
palm fronds.
HOPPER.
CHIPPING TIPS
• Rotate, insert, and retract thicker branches so that the engine runs at a
steady rate. Allow the rotor to recover and discharge the chips.
• Skinny prunings may be bundled and inserted together.
• Green materials chip easier and the knives keep their edges longer.
• Resharpen or replace the chipper knives when you notice that they do not
self-feed very well. Forcing debris into dull knives causes vibration and
will eventually damage or destroy the rotor.
• Shut down and empty the bag before it fills up and stalls the rotor.
Shredding
SHREDDER
HP
CAPACITY
TYPE OF DISCHARGE
Leaves, pine straw,
small plants, flowers,
bulbs, light prunings.
9 & 10
1” dia. x 36”
Fine mulch (greens) to
longer fingerling shreds.
Same as above.
SHREDDING TIPS
• Aim the waste butt-first down the right side of the shredder hopper (as
you stand behind it).
• Use an open-handed technique, loosely grasping the waste to throw it in.
Do not hold onto it.
• Pour—rather than dump—leafy waste into the shredder hopper.
• Chase waste stuck in the throat with a shreddable pruning. Or, use the
end of 3” thick branch to stir clumps until the rotor pulls them in.
• Vines are best fed down the chipper, followed by a thick branch.
• Green debris exceeding the length limitations may wrap around the rotor
and seriously plug up or damage the machine! Chip them.
• Materials that are too thick may stall the machine and possibly damage the
hammers, rotor, housings or hopper. Use the chipper.
page 12
Vacuuming
VACUUM (15-ft. kit optional)
Dry to wet leaves,
pine straw, sawdust,
grass clippings.
HP
9 & 10
CAPACITY
Loose waste
TYPE OF DISCHARGE
Fine mulch (leaves),
some fingerling shreds.
VACUUMING TIPS
• Keep the hose straight or slightly curved along the ground.
• Allow nozzle to hover over the waste, rather than sticking it into the pile.
• If the vacuum loses power, there may be a clog in the nozzle or in the
throat of the shredder hopper. Lift the hose over your head and shake it.
You may need to shut down, unplug the adaptor and unclog the
shredder’s throat.
• Don’t let the hose come in contact with the muffler. The muffler can get
hot enough to melt it.
❹ HOW IT WORKS
The chipper-shredder-vac must be operated with the bag in place. The bag
holds over two bushels, but emptying it often is a good habit. If it overfills,
debris may back up into the discharge chute and stall the engine—just like a
lawn mower does when it’s bag gets too full.
Direct-Bagging
“QUICK-FEED”
PRUNINGS DOWN
THE LEFT SIDE OF
THE SHREDDER
WITH A LOOSE,
OPEN GRIP.
Great will be the temptation...but do not begin to remove the bag until the
engine is shut off and the rotor has stopped.
Chipping
Waste fed down the chipper cone produces uniform, coin-sized chips. Two
sharp knives, mounted on the rotor, pass by the cone’s solid base at more than
3750 RPM, slicing the end of the branch into little chips.
The angle of the knives draws branches in as they are cut. Eventually, the
knives become dull. They must be removed and re-sharpened. Replace the
knives when their cutting surface nears one-eighth inch from the knives’
mounting holes.
Shredding
The shredder uses six Y-shaped hammers and the built-in vacuum to pull
waste into the grinder housing. The shredding hammers attached to the rotor
grab onto thicker debris. Material is ground and shredded until it is small
enough to be pulled into the fan chamber and discharged into the bag.
The rotor spins clockwise (as you stand behind the machine). The
hammers swing freely on shafts a full 360°. If material is too heavy to shred on
the first strike, they swing out of the way. The Y-forks do the shredding and
pulling. (Technically speaking, green debris is said to be “shredded”; drier,
leafier debris is “ground”.) Hammers eventually wear down and can be
replaced or simply reversed.
CAUTION: DO NOT LET GO OF BULKY
!
WASTE AND LET IT BOUNCE AROUND
IN THE HOPPERS. IT MAY DAMAGE
THE MACHINE OR BE EJECTED
TOWARD THE OPERATOR OR
BYSTANDERS AND CAUSE INJURY.
▲
Vacuuming
The four blade vacuum draws air into the housings through the shredder
hopper and chipper cone. To take full advantage of this air flow system, the
optional vacuum kit snaps into the hopper for a 15-ft. reach around the
machine.
page 13
Fixing Clogs, Stalls & Jams
WARNING: THE POWER MUST BE OFF,
THE ROTOR FULLY STOPPED AND THE
SPARK PLUG WIRE DISCONNECTED
FROM THE SPARK PLUG BEFORE ANY
SERVICE OR MAINTENANCE IS PER-
FORMED. OTHERWISE, PERSONAL
INJURY MAY RESULT!
Stalls, jams, and plug-ups most often occur when the machine is overloaded.
When vacuuming, walk slowly over heavy leaf coverage. When chipping,
insert and retract thick branches so that the rotor maintains a constant speed.
Do not put prunings down the shredder that exceed the diameter or length
capacities of the model you own (see page 11).
!
▲
If the chipper-shredder-vac clogs and stops, try the following:
1. Set throttle to STOP. Pull off the spark plug wire.
2. Check fuel supply. Did it run out of gas?
3. Put on some gloves to avoid sharp edges when digging out the inlets.
4. Remove collection bag, clean out discharge inlet.
4. Clear out chipper cone and shredder hopper.
Batten Down the Hardware
All the serrated fasteners, roll pins
and lockwashers have special locking
qualities when they’re new.
Whenever removing one for any rea-
son, use a new one in its place.
Inspect and tighten loose fasteners
before each use.
5. Gently pull the starter cord. If the rotor inside is turning freely,
re-attach the spark plug wire, bag, and re-start the engine.
6. If the jam is more serious, remove the chipper cone. Then, use a heavy
stick or probe to insert into discharge inlet, and push back against the
fan blades on the rotor. This will force clogged debris out the front
oval opening and the discharge inlet. Repeat until clear.
Ready to Go?
❏
❏
❏
Check oil and gas levels, attach spark plug wire.
Attach bagger-blower chute, T-bolts, hook bag on handle, close zipper.
Remove any objects from chipper cone.
Deflector Shields,
Hopper Guards & You
The deflector shield covering the dis-
charge chute and the flexible hopper
guard inside the shredder hopper are
designed to last a long, long time.
However, should either the guard or
the deflector somehow become dam-
aged, you must shut down the unit
and fix or replace them before contin-
uing any further.
❺ MAINTENANCE
Servicing the Hammers &
Sharpening the Knives
1
Shut off the engine, let the rotor stop,
disconnect the spark plug wire.
Remove the chipping cone assembly
at its base with a 1/2” wrench.
(To service the knives,
go directly to Step 8 on page 15.)
2
Disassemble the discharge deflector
and the bag retaining bolt
underneath the discharge chute
using two 1/2” wrenches.
CAUTION: TURN OFF THE ENGINE,
WAIT FOR THE ROTOR TO
!
▲
STOP TURNING AND DISCONNECT THE
SPARK PLUG WIRE BEFORE ATTEMPT-
ING TO SERVICE THE HAMMERS OR
KNIVES. FAILURE TO SHUT DOWN
PROPERLY CONSTITUTES NEGLIGENT
BEHAVIOR AND MAY RESULT IN PER-
SONAL INJURY.
page 14
3
SET SCREW
Loosen the lock collar by unscrewing
and removing the set screw with an
1/8” Allen wrench. Insert a pin
punch and tap at an angle with a ball
peen hammer, turning the collar
clockwise until you can remove it.
(Before reassembling the collar, use
sand paper to smooth the burr where
the set screw enters the hub. Be sure
the collar mounts flush with the out-
side of the rotor bearing shaft.)
THE VACUUM
(OPTIONAL)
WORKS BEST
WHEN YOU
LOCK COLLAR
LET THE NOZZLE
HOVER OVER
THE WASTE.
4
Remove the flange nuts from around
the perimeter of the fan housing.
Next, loosen but do not remove the
three flange nuts holding the triangu-
lar flangettes over the bearing. Pull
apart the housings, then take off the
flangettes and remove the entire fan
housing. Position it underneath the
unit, as seen in the next drawing...
5
Note how the fan housing has been
placed underneath. Put a rag there,
too, to avoid scratching the housing.
Use a 9/16” wrench to remove the
3/8” bolt from the center of the rotor
shaft. (When reassembling, use a
torque wrench to tighten this bolt to
45 ft.-lbs.)
CAUTION: FOR YOUR SAFETY
AND TO MEET NATIONAL SAFETY
STANDARDS, THE DISCHARGE
DEFLECTOR AND HOPPER GUARD
MUST BE MAINTAINED IN GOOD CON-
DITION. SERIOUS PERSONAL INJURY
MAY OCCUR IF THE SHIELD OR
DEFLECTOR ARE NOT INTACT. IT IS
THE OPERATOR’S RESPONSIBILITY TO
MAINTAIN THESE SAFETY DEVICES.
!
▲
6
Pull the rotor from the crankshaft by
turning the rotor back and forth.
There may be some resistance. Pull it
off steadily, making sure that the
hammers clear the inner wall of the
center plate. (When reassembling,
coat the exposed engine shaft and
key with a liquid graphite or slip
plate type compound.)
CAUTION: THE ROTOR WILL COAST
EVEN AFTER THE ENGINE IS OFF. MAKE
SURE THIS ASSEMBLY IS FULLY
STOPPED AND DISCONNECT THE
SPARK PLUG WIRE BEFORE ANY
MAINTENANCE OR SERVICE IS
PERFORMED. IF THE ROTOR IS STILL
TURNING, IT MAY CAUSE SERIOUS
PERSONAL INJURY.
!
▲
page 15
7
Service one hammer assembly at a
time. Use a ball peen hammer and
pin punch to remove the roll pins
from each spacer and shaft as shown.
(Discard the roll pins. Use new pins
during reassembly.) Pull the shaft
out of the rotor, catching the spacers
and hammers with your free hand.
Inspect the shafts and spacers for
unusual wear. Replace them, if nec-
essary.
Single hammer, fork
facing in.
Reverse each worn hammer, or
replace them as need be. Note how
the Y-hammers are positioned in
relation to one another. Shafts with
two hammers must be reassembled
so that the bent prongs face inward
and towards one another; the single
hammers face their prongs in oppo-
site, outward directions. Secure the
spacers with new roll pins using your
ball peen hammer and punch pin.
Single hammer, fork
facing out.
If not servicing the knives, reassemble
your unit by following 1 through 6 in
reverse order.
CORRECT “STAGGERING”
OF HAMMERS
8
SHOWN HERE:
Removing a
With the chipper cone and base
removed, slowly turn the rotor clock-
wise with a probe until a chipper
knife appears in the hole. First,
scrape out any pulp embedded in the
heads of the screws. Loosen the
screws using the 3/16” Allen wrench
provided with your unit. Unscrew
them by hand and remove the knife.
Rotate the rotor slowly and remove
the second knife in this same way.
Sharpen the knives evenly at 30°
angles. A homeowner’s bench
grinder with a fine grit stone will do,
but because the knives are specially
treated, too much heat will make
them brittle. Grind only a little bit
at a time and allow them to cool.
Slow-speed, water-cooled grinding is
preferred. For best results, see your
local machine shop specialist.
knife without
disassembling
the housings.
Sharpen the
chipping knives
when they
lose their
self-feeding
action.
Knives must be replaced once the
bases of their cutting edges are
ground within 1/8” of the mounting
holes.
Minimum
distance = 1/8”
Reassemble your chipper-shredder-vac by
following these instructions in reverse.
page 16
Bitten by the Bug?
•
“The Rodale Book of
Composting,” by the editors of
Rodale Press.
“The Mulch Book,” by Stu
Campbell (Storey Publishing).
“Worms Eat My Garbage,” by
Mary Apelhof (Flower).
“Yardening,” by Jeff and Liz
Ball (MacMillan).
❻ WHAT TO DO WITH THE STUFF
NOW THAT IT’S ALL
•
•
•
CHIPPED & SHREDDED
The chips, shreds and mulch you make are valuable organic materials for
your lawn and garden. Put them to good and immediate use—even if you
are not an avid green thumb-er.
Landscape & Garden
Use the reduced materials to make a garden path and to edge saplings or
shrubs. An inch or so holds in moisture, moderates temperatures and erosion,
and reduces weed and turf growth. They also protect exposed root systems
and tender bulbs from unpredictable elements.
Composting
Whole books have been written on the subject. A good compost pile will not—
contrary to popular opinion—smell like a landfill and attract critters. One rule
of thumb for a proper pile is, “Equal weights of green and brown help to break
the microbes down.” (Note well the word weights, as opposed to parts!)
Your basic compost pile is a three layer salad that is 4’ x 4’ x 4’. Simply
put it in a pile, or dig a pit or a trench. Some fancy containers speed things
along and look nicer.
Things you can’t use? Animal wastes, bones and meat scraps.
BROWN, 3” - 5”
Some old leaves or twiggy brush on the bottom helps air
enter the pile.
GREEN, 3” - 5”
Leafy, non-woody stuff. Include grass clippings and kitchen
scraps. But no meat, fat or dairy products.
SOIL OR COMPOST STARTER, 1”
This layer of micro-organisms does the dirty work. If you’re so inclined,
a handful of granular fertilizer jump starts it, feeding the organisms.
Wet the pile as needed to keep the center the consistency of a damp
sponge. Continue to add layers until it is up to four feet high and deep. Turn
the pile once a week or so with a shovel or pitch fork. Turning and wetting
the pile is what the pros call “fast” or “hot” composting, with temperatures
inside the pile reaching 160° F.
How Long Until Soup’s On?
Depending on how well it is tended, in two to four weeks the compost
is ready for use in your garden. Better still, you can’t “spoil” the recipe.
If offending odors emerge, it may be due to too much moisture, green
materials, or critter droppings. Mix in more brown, turn the pile often,
or cover it with plastic to keep it dry.
page 17
❼ ILLUSTRATED PARTS LIST
The “Illus. #” refers to the numbered parts in the illustrations. Use the Component #” and the “Item Description”
when ordering. “Qty.” refers to the total number of each part the machine is built with. Items without an
“Illustration #” are available but not shown in the drawings.
Illus. # Component
#
Item Description
Qty.
Illus. # Component
#
Item Description
Qty.
1
1
825150090 HONDA 9 HP GX270 ENGINE
825150010XL 10 XL/C TECUMSEH, 1” SHAFT
1
1
34
35
700020005
717520005
TRUSS HEAD SELF-TAPPING
SCREW, #14 x 5/8
5
HEX HEAD CAP SCREW,
5/16-18 x 3-1/4”
LYNCH PIN
2
2
300010690
300000580
ENGINE MOUNT HONDA-IG
PRO ENGINE MOUNT/AXLE
1
1
2
1
4
1
1
1
*
36
37
38
39A
39B
710220005
703200005
703100005
802022135
702000005
ROLL PIN, 3/16 x 3/4”
KEY, 1/4” SQUARE x 1-7/8”
FLANGETTE, INNER
FLANGETTE, OUTER
3
4
302010215
325002085
GRINDER HOUSING (Call Factory)
ROTOR TRI-PLATE 1" BORE
1
1
5
6
7
8
8B
9
103009035
204009045
211009075
211009055
265001895
211009355
265001905
810009015
Y HAMMERS
HAMMER SHAFT
6
4
2
2
2
2
2
2
40
41
42
43
44
709920005
800070435
800070445
800070450
800070455
PUSH NUT, 5/8”
DANGER DECAL
2
3
1
1
SPACER A (short, plain)
SPACER B (short w/ hole)
ROLL PIN SLEEVE B
SPACER C (long w/ hole)
ROLL PIN SLEEVE C
CHIPPER KNIFE
CAUTION DECAL
OPEI CERTIFICATION DECAL
SERIAL NUMBER TAG (CALL FACTORY) 1
9C
10
45
800070845
810051999
1” SIZE LIMIT DECAL, 9 & 10 HP
ENGINE SPACERS HONDA 9 HP
1
2
46
*
11
12
13
303010235
302010255
612010275
CENTER PLATE
FAN HOUSING
LEG
1
1
1
Convenient kits also available...
14
15
16
17
18
19
400010365
500050515
CHIPPER CONE CASTING
SHREDDER HOPPER, BLACK
1
1
1
1
1
1
PAT-CSVVAC-KIT VACUUM KIT (see page 8)
1
1130103905A DISCHARGE DEFLECTOR
500050375A CHIPPER CONE
993090035
990000015
990010395
990000455
Y-HAMMER KIT w/ shafts, hardware
CHIPPER KNIFE KIT w/ hardware
DEFLECTOR KIT
1
1
1
1
114050345
700060405
HOPPER GUARD
COLLECTION BAG, 24” x 36”
PLASTIC HARDWARE KIT
20
709040010
SEMI-PNEUMATIC TIRE
2
990060010
SEMI-PNEUMATIC WHEEL KIT
1
21
22
22
23
24
24
25
708000005
706520005
768520005
705520005
718520005
751520005
705720005
BEARING, 1” BORE & LOCK COLLAR
HEX HEAD CAP SCREW, 5/16-24 x 3/4”
HEX HEAD CAP SCREW, 5/16-20 x 1” Gr.5
HEX HEAD CAP SCREW, 5/16-18 x 3/4” Gr. 5
HEX HEAD CAP SCREW, 5/16-18 x 1-1/4”
1
4
4
2
4
703050005
719050005
ALLEN WRENCH, 3/16”
ALLEN WRENCH, 5/32”
1
1
920000005B ASSEMBLY HARDWARE BAG,
for assembly out of the box
*
1
1
1
700000005
990070005
800070010
SAFETY GOGGLES
HEX HEAD CAP SCREW, 5/16-18 x 1-3/4” Gr.5
BUTTON HEAD SOCKET CAP
SCREW, 5/16-18 x 1/2”
2
WARNING/CAUTION DECALS KIT
OWNER/OPERATOR MANUAL
PACK 3100/3090H
*
7
1
1
26
768800000
FLAT HEAD SOCKET CAP SCREW,
5/16-24 x 1”
800070595P PATRIOT WARRANTY CARD
(CALL 1-800-798-2447)
4
4
27
27
28
28
29
30
31
715520005
715530005
716620005
704620005
705620005
705320005
HEX HEAD CAP SCREW, 3/8-24 x 4-1/2”
HEX HEAD CAP SCREW, 7/16-20 x 5” Gr. 8
LOCK WASHER, 3/8 SPLIT RING
LOCK WASHER, 7/16
1
*
*
*(For CSV-3090H)
[2/98]
4
1
LOCK WASHER, 5/16 SPLIT RING
SERRATED FLANGE NUT, 5/16-18
4
23
707320005L HEX HEAD REVERSIBLE LOCK
NUT, 1/4”-20
8
32
33
707720005
BUTTON HEAD CAP SCREW,
1/4-20 x 3/4”
1/4” SAE FLATWASHER
8
8
710620005
page 18
CAUTION: THE ROTOR WILL COAST
EVEN AFTER THE ENGINE IS OFF. MAKE
SURE THE ROTOR IS FULLY STOPPED
AND DISCONNECT THE SPARK PLUG
WIRE BEFORE ATTEMPTING ANY
MAINTENANCE OR SERVICE. IF THE
ROTOR IS STILL TURNING, IT
MAY CAUSE SERIOUS PERSONAL
INJURY.
!
▲
REAR VIEW
42
45
The circled numbers here refer to the
numbers in the first column of the parts
list.
19
43
15
6
7
5
8
44
3
1
37
8B
37
6
37
5
9
5
9C
9
5
9C
37
6
5
4
7
5
8
8B
Several patents approved or pending.
page 19
FRONT VIEW
CAUTION: THE ROTOR WILL COAST
EVEN AFTER THE ENGINE IS OFF. MAKE
SURE THE ROTOR IS FULLY STOPPED
AND DISCONNECT THE SPARK PLUG
WIRE BEFORE ATTEMPTING ANY
MAINTENANCE OR SERVICE. IF THE
ROTOR IS STILL TURNING, IT
MAY CAUSE SERIOUS PERSONAL
INJURY.
The circled numbers here refer to
the first column of numbers in the
parts list.
!
▲
34
18
41
15
(washers)
33
31
(screws)
32
31
24
38
1
12
3
11
4
46
41
23
30
(washers)
(screws)
16
33
32
35
(washers)
(screws)
17
32
40
30
2
20
31
(screws)
22 29
33
25
31
21
26
10
39A
30
39B
30
30
30
14
27
28 21
13
36
Several patents approved or pending.
page 20
CAUTION: THE ROTOR WILL COAST
EVEN AFTER THE ENGINE IS OFF. MAKE
SURE THE ROTOR STOPS TURNING,
THEN DISCONNECT THE PLUG
WIRE FROM THE ENGINE BEFORE
ATTEMPTING ANY MAINTENANCE OR
CLEAN-OUT. IF THE ROTOR IS STILL
TURNING, IT MAY CAUSE SERIOUS
PERSONAL INJURY.
!
▲
31
33
32
Detail of the shredder hopper.
Nuts (outside)
Screws (inside)
Washers (inside)
31
32
33
Nut
31
Washer
Screw
33
Both the shredder hopper and the chipper cone are
assembled with the same hardware and wrench.
32
21
bearing
set
screw
lock
collar
29
27
39A
39B
Detail of the outboard bearing assembly.
The bearing is sealed and does not need
lubrication.
30
BLANK PAGE 21
BLANK PAGE 22
BLANK PAGE 23
❽ TROUBLE-SHOOTER
CAUTION: BEFORE ATTEMPTING TO REMEDY PROBLEMS WITH YOUR CHIPPER-SHREDDER-VAC, TURN THE ENGINE OFF, WAIT FOR THE ROTOR TO
STOP TURNING, AND DISCONNECT THE SPARK PLUG WIRE. FAILURE TO DO SO CONSTITUTES NEGLIGENT BEHAVIOR AND MAY RESULT IN PROPERTY
DAMAGE AND SERIOUS PERSONAL INJURY.
!
▲
PROBLEM
CAUSE
REMEDY
Engine won’t start.
❶ Check fuel, oil, choke, and spark plug wire. ❶ That was easy enough!
Grinds, smokes, stalls.
❷ Old gas, dirty oil or air filter, bad plug.
❷ Drain or run out old gas. Change
oil and filter. Replace spark plug.
Unusual vibration,
rubbing noises.
❶ Sticky debris lodged on rotor.
❷ Chipper knife is loose.
❶ Clear debris out of discharge area.
❷ Check fasteners and knives for
damage. Re-secure and/or repair.
❸ Check the rotor for balance by
watching it turn while slowly
❸ Damaged knives, hammers, or rotor.
pulling the cord. If it wobbles, see
a Patriot service center immediately.
Debris does not chip easily.
❶ Throttle speed too low. Engine problem.
❷ Dull or damaged knives.
❸ Wood is dead, old, takes more effort.
❶ Run at maximum throttle.
❷ Sharpen or replace immediately!
❸ Alternate with green waste to
keep knives cool and sharp.
❹ Feeding rate too fast for discharge rate.
❹ Feed thicker waste at a slower rate.
Clogs while shredding,
not vacuuming well.
❶ Debris may be too bulky or wet.
❷ Hammers worn, broken.
❶ Feed more slowly. Add dry stuff.
❷ Replace the hammers.
❸ Debris stuck in grinder housing.
❸ Shut down. Unclog or run water
down the shredder.
Chronic clogging,
vibration, rattling.
❶ Engine not up to par.
❷ Internal damage or failure to rotor.
❶ Contact an engine service center.
❷ Contact a Patriot service center.
NOTES/SERVICE HISTORY
|