User Guide
MOTOROLA BRUTETM i680
www.nextel.com
©2009 Sprint. SPRINT and the NEXTEL name and logo are trademarks
of Sprint. Other marks are the property of their respective owners.
2/2/10
FCC Notice to Users
DECLARATION OF CONFORMITY
The following statement applies to all products that have
received FCC approval. Applicable products bear the FCC
logo, and/or an FCC ID in the format FCC-ID: IHDT56KD1 on
the product label.
Per FCC CFR 47 Part 2 Section 2.1077(a)
Motorola has not approved any changes or modifications to
this device by the user. Any changes or modifications could
void the user’s authority to operate the equipment. See 47 CFR
Sec. 15.21.
Class B Digital Device
Responsible Party Name: Motorola, Inc.
As a personal computer peripheral, this device complies with
part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation. See 47 CFR Sec. 15.19(3).
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: i680
Model Number: H85XAH6JR5AN
FCC-ID: IHDT56KD1
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section
15.109(a)
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Ⅲ Reorient or relocate the receiving antenna.
Ⅲ Increase the separation between the equipment and
receiver.
Ⅲ Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Ⅲ Consult the dealer or an experienced radio/TV
technician for help.
Table of Contents
Maintaining Safe Use of and Access to Your
Motorola Limited Warranty
Introduction
Note: Because of updates in phone software, this printed
guide may not be the most current version for your
phone. Visit www.nextel.com and sign in to access the
most recent version of the user guide.
This User Guide introduces you to your wireless service
and all the features of your new phone.
WARNING: Please refer to the Important Safety Information
that will help you safely use your phone. Failure to
read and follow the Important Safety Information
in this phone guide may result in serious bodily
injury, death, or property damage.
Throughout this guide, you’ll find tips that highlight
special shortcuts and timely reminders to help you
make the most of your new phone and service. The
Table of Contents and Index will also help you quickly
locate specific information.
You’ll get the most out of your phone if you read each
section. However, if you’d like to get right to a specific
feature, simply locate that section in the Table of
Contents and go directly to that page. Follow the
instructions in that section, and you’ll be ready to use
your phone in no time.
i
Use and Care
To care for your Motorola phone, keep it away from:
liquids of any kind
cleaning solutions
The MOTOROLA BRUTETM i680 is
designed to withstand being exposed to
blowing rain when the battery door is
attached properly, and the headset jack
and microUSB connector are properly
covered and sealed. Exposure to other
liquids should be avoided, especially
corrosive liquids.
To clean your phone, use only a dry soft
cloth. Don’t use alcohol or other
cleaning solutions.
extreme heat or cold
Don't expose your phone to extreme
high or low temperatures outside of
-10°C/14°F or above 45°C/113°F.
microwaves
Don’t try to dry your phone in a
microwave oven.
ii
Setting Up Your Phone
1. Setting Up Service
1. Make sure your SIM card is in place.
2. Install the battery.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ 3. Press and hold the End/Power Key (@) for two
seconds to turn the phone on.
Ⅲ If your phone is activated, it will turn on, search for
service, and enter standby mode.
● If your phone's SIM PIN is set, you may be
prompted to enter your SIM PIN code when
you turn on your phone. Enter the four-digit
number and press the left softkey (the top left
key below the display screen) to select Ok.
Press Yes (left softkey) to allow phone
Your Phone’s Navigation Pad
Softkeys (-)
(;) Navigation Key
transmissions as prompted. (See “SIM Card
Menu Key (/)
(?) Camera Key
Talk Key (`)
(@) End/Power Key
(r) OK Key
Note: You may see a prompt to update your browser
information. Press Ok (left softkey) to complete the task.
1
4. Make your first call.
prompts showing what to do next. If you still
encounter security messages, call Nextel Customer
Service at 1-800-639-6111 from any other phone.
Ⅲ Use your keypad to enter a phone number.
Ⅲ Press the Talk key (`).
Note: Your phone’s battery should have enough charge for
your phone to turn on and find a signal, set up your
voicemail, and make a call. You should fully charge
your battery as soon as possible. See “Charging the
Setting Up Voicemail
All unanswered calls to your phone are automatically
transferred to your voicemail, even if your phone is in
use or turned off. Therefore, it is recommended that you
set up your voicemail and personal greeting as soon
as your phone is activated.
Activating Your Phone
1. Using your MOTOROLA BRUTE, call your wireless
phone number.
ⅷ If you purchased your phone at a Nextel Store, it is
probably activated and ready to use.
2. Follow the system prompts to:
Ⅲ Create your passcode.
ⅷ If your phone is not activated, please call Nextel
Customer Service at 1-800-639-6111 from any other
phone.
Ⅲ Record your name announcement.
Ⅲ Record your greeting.
Tip: You must be in an area covered by the Nextel National
Network when you first power up your phone.
Note: Voicemail Passcode: It is strongly recommended that
you create a passcode when setting up your voicemail
to protect against unauthorized access. Without a
passcode, anyone who has access to your phone is
able to access your voicemail messages.
ⅷ When you power up your phone the first time, it
performs a series of security checks. For example, it
verifies the phone is Nextel-approved and the correct
SIM card is installed. If you don’t pass the security
checks, your phone displays messages and screen
2
For more information about using your voicemail, (see
Account Passwords
With Nextel service, you enjoy unlimited access to your
personal account information and voicemail account.
To ensure that no one else has access to your
information, you need to create passwords to protect
your privacy.
Enabling Security
You must enable security the first time you power on
your phone or within ten days of first activating your
phone.
Account Username and Password
1. Press and hold @for two seconds to power on
your phone.
If you are the account owner, you will create an account
username and password when you sign on to
www.nextel.com. (Click Need to register for access? to get
started.) If you are not the account owner (if someone
else receives the bill for your service), you can get a
sub-account password at www.nextel.com.
2. Press Ok (right softkey).
3. You are prompted to enable security. Press Yes
(right softkey). A series of screens followed by the
default homepage displays.
Note: When you go to www.nextel.com, you will be redirected
to www.sprint.com by default. Follow the sign in
4. Press @to return to standby mode.
instructions above to access your Nextel account.
Voicemail Password
You will create your voicemail password (or passcode)
when you set up your voicemail. See “Setting Up
Voicemail” on page 2 for more information on your
voicemail password.
3
Operator Services
Getting Help
Operator Services provides assistance when you place
collect calls or when you place calls billed to a local
telephone calling card or third party.
Managing Your Account
Online: www.nextel.com
ᮣ
Press
0`.
ⅷ Access your account information.
For more information or to see the latest in products
and services, visit us online at www.nextel.com.
ⅷ Check your minutes used (depending on your
service plan).
ⅷ View and pay your bill.
ⅷ Enroll for online billing and automatic payment.
ⅷ Purchase accessories.
ⅷ Shop for the latest phones.
ⅷ View available service plans and options.
From Your MOTOROLA BRUTE
ⅷ Press *4
`
to check minute usage and account
balance.
ⅷ Press *3
`
to make a payment.
From Any Other Phone
ⅷ Nextel Customer Service: 1-800-639-6111.
ⅷ Business Customer Service: 1-877-639-8351.
4
3. Talk Key (`) allows you to place or receive calls,
Closed View
answer Call Waiting, or use Three-Way Calling.
11. Audio Jack
4. Navigation Key scrolls through the phone’s menu
options and acts as a shortcut key from standby
mode.
12. Speaker
Button
17. Smart Button
5. Back Key (*) deletes characters in text entry
mode. When using the Web, it allows you to return
to the previous page.
16. Noise
13. Volume
Cancellation
Button
Microphone
14. Direct
Connect
Button
6. Space Key (#) enters a space in text entry mode.
7. End/Power Key (@) allows you to end calls, return
to standby mode, or turn the phone on or off.
15. Micro USB
Connector
8. Camera Key (?) allows you to activate the phone’s
camera.
9. OK Key (r) selects the highlighted choice when
navigating through a menu.
Key Functions
10. Right Softkey (-) lets you select softkey actions
corresponding to the bottom right line on the
display screen.
1. Left Softkey (-) lets you select softkey actions or
menu items corresponding to the bottom left line
on the display screen.
11. Audio Jack allows you to connect your
headphones to your phone.
2. Menu Key (/) lets you access the phone’s menu
from standby mode and allows you to access
context-sensitive menus from other screens.
6
12. Speaker Button ()) lets you place or receive calls
in speaker mode. In standby mode, pressing the
speaker button turns Direct Connect speaker
mode on and off.
17. Smart Button (() anticipates the next action you
are likely to perform. For example, when you
highlight a menu item, you can press the Smart
Button to select it. You can also use the Smart
Button to end calls when your phone is closed.
13. Volume Button allows you to adjust the ringer
volume in standby mode, the voice or speaker
volume during a call, and the speaker volume
while using the music player or other applications.
Note: The use of wireless phones while driving may cause
distraction. Discontinue a call if you can’t concentrate
on driving. Additionally, the use of wireless devices and
their accessories may be prohibited or restricted in
certain areas. Always obey the laws and regulations on
the use of these products.
14. Direct Connect (DC) Button allows you to use Nextel
15. Micro USB Connector allows you to connect your
charger or other accessories to your phone.
Getting Started With Your Phone
16. Noise Cancellation Microphone eliminates ambient
To start using your MOTOROLA BRUTE:
ⅷ Make sure your SIM card is in place.
ⅷ Charge the battery.
noise to provide improved, clearer call quality.
WARNING: Do not cover the Noise Cancelation Microphone
while making a phone call. If covered the sound
quality of your phone call will be affected.
ⅷ Turn on your phone.
Note: The Noise Cancellation Microphone does not function
when you are on the speaker phone or making a Direct
Connect call.
After you’ve completed these items, you are ready to
begin using your new phone.
7
Removing and Inserting the SIM Card
Your SIM Card
Important: To avoid losing information stored in your SIM
card, do not remove it from your phone unless
absolutely necessary.
Locating the SIM Card
Your SIM (Subscriber Identity Module) card is a small
card inserted into the SIM card holder within your
phone below the battery.
To remove your SIM card:
1. With your phone powered off, turn the release tab
counter-clockwise to release the battery cover, and
then remove the battery cover from the back of the
phone.
If no SIM card came with your phone, contact Nextel
Customer Service at 1-800-639-6111.
Most users will never need to remove or insert the SIM
card. However, if it becomes necessary, follow the
instructions in “Removing and Inserting the SIM Card”
2. Remove the battery, and then use your thumbs to
carefully slide the SIM card out from under the
edge.
Important: The SIM card is designed for optimal Contacts
storage and feature use. For Nextel SIM card
compatibility information, visit
In some cases, Contacts and Groups may not be
accessible if you move your SIM card to another
phone. Contacts and Groups created with your
MOTOROLA BRUTE may not be readable by an
older iDEN SIM-based phone.
8
Battery and Charger
Note: Protect your SIM card as you would any delicate object.
Store it carefully.
WARNING: Use only Nextel-approved or Motorola-approved
batteries and chargers with your phone. The
failure to use a Nextel-approved or Motorola-
approved battery and charger may increase the
risk that your phone will overheat, catch fire, or
explode, resulting in serious bodily injury, death,
or property damage.
To insert your SIM card:
1. With your phone powered off, turn the release tab
counter-clockwise to release the battery cover, and
then remove the battery cover from the back of the
phone.
2. Remove the battery, and then use your thumbs to
carefully slide the SIM card into your phone until it
lies flat in the SIM card holder.
Nextel-approved and Motorola-approved batteries and
accessories can be found at Sprint Stores or through
Motorola. You may order online at www.nextel.com or by
calling 1-866-866-7509.
Important: Do not touch the gold-colored areas of your SIM
card.
Your phone’s Lithium Ion (Li-Ion) battery allows you to
recharge it before it is fully drained.
When the battery reaches 5% of its capacity, your
phone makes a sound and displays a message. When
there are approximately two minutes of talk time left, the
phone sounds an audible alert and then turns off.
9
WARNING: Do not use a sharp object to unlock the battery
Note: Long backlight settings, searching for service, vibrate
mode, browser use, and other variables may reduce
the battery’s talk and standby times.
door as it may damage the lock.
2. Place the tip of your finger in the battery door
recess, and lift the battery door to remove it from
the phone.
Tip: Watch your phone’s battery level indicator and charge the
battery before it runs out of power.
Installing the Battery
1. Press down on the battery door latch, and with a
coin, turn it counter-clockwise to the unlocked
position.
Battery Door
Recess
3. Insert the battery into the opening, making sure the
connectors align. Gently press down to secure the
battery.
Battery Door
Recess
10
4. Replace the battery cover and firmly press it down
into place to ensure a proper watertight seal. With
a coin, turn the battery door latch clockwise to the
locked position.
Charging the Battery
Charge your battery as soon as possible so you can
begin using your phone.
Always use a Nextel-approved or Motorola-approved
desktop charger, travel charger, or vehicle power
adapter to charge your battery.
Using the Phone Charger
ᮣ
Plug the flat end of the charger into the phone’s
micro USB connector and the other end into an
electrical outlet.
WARNING: If the battery door is not properly installed, your
phone will not have a watertight seal. If the phone
comes into contact with blowing rain, damage
will occur.
Removing the Battery
1. Make sure the power is off so that you don’t lose
any stored numbers or messages.
2. Remove the battery cover and position your
fingernail on the top end of the battery to remove it.
WARNING: Do not handle a damaged or leaking Li-Ion
battery as you can be burned.
With the approved Li-Ion battery, you can recharge the
battery before it becomes completely run down.
11
and the audio jack and microUSB port must be
properly sealed.
Water Resistance
Audio Jack
WARNING: Exposing your phone to water outside of these
limits, or not using the precautions stated, can
result in water damage.
Turning Your Phone On and Off
Turning Your Phone On
ᮣ
Press and hold @for approximately two seconds.
As your phone connects to the network, you see a
connecting message. Your phone may require you to
enter identifying information to use it or to access
specific features.
MicroUSB
Connector
Note: If your phone's SIM PIN is set, you will be prompted to
enter your SIM PIN code when you turn on your phone.
Enter the four-digit number and press Ok (left softkey).
Press Yes (left softkey) to allow phone transmissions as
prompted.
Battery Door
Latch
Turning Your Phone Off
Your phone is designed to withstand being exposed to
blowing rain. In order for your phone to be watertight,
the battery door must be properly attached and locked,
ᮣ
Press and hold @for two seconds until you see
the powering down animation on the display
screen.
12
Your screen remains blank while your phone is off
(unless the battery is charging).
Group In Use — Your phone is active on a
Group Connect call.
t
4
r
c
Direct Talk — Your phone is off network and set
to Direct Talk mode.
Viewing Status Information
Your phone’s display screen provides information
about your phone’s status and options. This list
identifies the symbols you’ll see on your phone’s
display screen:
Talkgroup In Use — Your phone is active on a
Talkgroup call.
Bluetooth In Use — Your phone is using
Bluetooth. If this icon is blinking, your phone is
in discoverable mode. If this icon is static, a
Bluetooth connection is active.
Battery Strength — A fuller battery indicates a
greater charge. The “plug” icon (bottom rows)
indicates the phone is charging.
d e
f g
y x
w h
Active Phone Line — 1 indicates phone line 1
is ready to make calls; 2 indicates phone line 2
is ready to make calls.
%'
Signal Strength — More bars next to the
antenna indicate a stronger signal.
z {
|}
Call Forward — Your phone is set to forward
&)
;(
No Service — Your phone is without service.
You cannot make or receive any type of call.
~
*<
/5
,
Phone In Use — Your phone is active on a
phone call.
$
Direct Connect In Use — Your phone is active
on a Direct Connect call.
0
13
Speaker Off — Direct Connect sound is set to
come through the earpiece rather than through
the speaker.
Hearing Aid — Your phone is set for use with a
hearing aid and is active on a phone call. See
"
W
Messages — You have one or more messages.
2 6
1 3
5
Voice Record — You have one or more voice
records stored. See “Voice Records” on
:
Text Input — You are using one of the phone’s
text entry methods. See “Selecting a Text Input
QRS
WX
Navigating Through Menus and
Options
Internet — You are ready to browse the Internet
or are browsing the Internet using a secure
connection. See “5. Data Services” on page 66.
ᮣ
Press /to access the main menu, and then use
the navigation key to scroll through menu items.
7 >
?
To navigate through a list-type menu, simply press your
navigation key up or down. The scroll bar at the right of
the menu keeps track of your position in the menu at
all times.
Transmitters — Your phone is set not to receive
calls and other transmissions. See “Airplane
L
TTY — You are ready to use your phone to
make calls using a TTY (text telephone) device.
AB
Many features provide context-sensitive menus that let
you access related features and actions. This icon f
appears onscreen any time a context-sensitive menu is
available. Press /to access the menu.
14
Selecting Menu Items
Shortcuts and Personalized Keys
As you navigate through the menu, menu options are
highlighted. Select an item by highlighting it and
pressing r.
In standby mode, your phone gives you ways to quickly
access features you use frequently:
access most menu options by pressing a number on
your keypad or saying the voice name of the
shortcut.
For example, to view your text messages:
1. Press /to access the main menu.
2. Select Messages by highlighting Messages and
menu items to the navigation keys, softkeys and r,
reorder the main menu, and set a main menu item to
appear when you turn on your phone.
pressing r.
3. Select Inbox by highlighting it and pressing r.
(If you have any MMS messages, they are
displayed.)
Help
Note: For the purposes of this guide, the above steps
Your phone contains an in-device help program to
help you understand complicated or seldom used
features. When you access a feature, Help sometimes
appears as a menu item or softkey. Select Help and
read the text for a quick overview of the feature. For
more information, refer to this guide.
condense into “Press /> Messages > Inbox.”
Backing Up Within a Menu
To go to the previous menu:
ᮣ
Press Back (right softkey).
To return to standby mode:
Press @.
ᮣ
15
Ⅲ Symbols to enter punctuation and other symbols.
Displaying Your Numbers
Ⅲ Numeric to enter numbers by pressing the
My Info lets you view your phone number, Direct
Connect number, and other phone information.
Ⅲ Text Input Settings allows you to change the
ᮣ
Press /> Tools > My Info.
Ⅲ Insert to insert Quick Notes preset messages
(Insert QNotes) or additional multimedia elements
such as pictures or audio files into a message.
by pressing QNotes [left softkey] when beginning
a message.)
Entering Text
Selecting a Text Input Mode
Your phone provides convenient ways to enter letters,
numbers, and symbols whenever you are prompted to
enter text (for example, when adding a Contacts entry
or when composing text and multimedia messages).
Tip: When entering text, press and hold the #to change
letter capitalization (ABC > Abc > abc).
To choose a text input mode:
Entering Text Using Word Text Input
1. At a screen requiring you to enter text, press /to
change the text input mode.
Word Text Input (T9) reduces the number of keystrokes
needed to enter a word by predicting complete words
as you type. While you enter letters, Word mode
matches your keystrokes to words in its database and
displays the most commonly used matching word. You
can add your own words to this database.
2. Select one of the following options:
Ⅲ Alpha to enter text directly using the keypad.
Ⅲ Word to enter text using a predictive text system
that reduces the number of key presses required
16
1. Select the Word text input mode.
The word will appear as an option the next time you
scroll through options during Word Text Input.
2. Press the corresponding keys once per letter to
enter a word. (For example, to enter the word “Bill,”
press 2455.) (If you make a mistake, press
Delete [left softkey] to erase a single character.
Press and hold Delete [left softkey] to erase an
entire entry.)
Tip: You cannot store alphanumeric combinations such
as Y2K.
To change the text input settings:
1. On a text entry screen, press /.
2. Select Text Input Settings.
3. To accept a word and insert a space, press #.
4. If the word that appears is not the desired word,
press the navigation key up or down to change the
word on the display to the next most likely word in
the database. Repeat until the desired word
appears.
3. Select your Primary Input and Secondary Input
language, and whether you want Complete Word
and Word Predict features to be on or off.
Entering Text Using Alpha Mode
Adding a Word to the Database
If a specific word is not displayed as an option when
you are using Word, add it to the database.
2. Press the corresponding keys once per letter to
enter a word. (For example, to enter the word “Bill,”
press 2twice, 4three times, 5three times,
and 5three times again. (If you make a mistake,
press Delete (left softkey) to erase a single
character. Press and hold Delete (left softkey) to
erase an entire entry.)
3. Select the Word text input mode.
17
By default, the first letter of an entry is capitalized and
the following letters are lower cased. After a character
is entered, the cursor automatically advances to the
next space after two seconds or when you enter a
character on a different key.
Entering Symbols, Numbers, and Quick
Notes
To enter symbols:
ᮣ
Input Mode” on page 16.) To enter a symbol,
highlight it and press r.
Characters scroll in the following order:
English Sequence
Space . ? ! , @ & : ; “ - ( ) ‘ ¿ ¡ % £ $ ¥
A B C 2 Á Ã Â À Ç
D E F 3 É Ê È
G H I 4 Í Ì
J K L 5
Key
To enter numbers:
ABC
DEF
ᮣ
Select the Numeric mode and press the
appropriate key. (See “Selecting a Text Input
GHI
JKL
To enter Quick Notes:
MNO
PQRS
TUV
WXYZ
M N ñ O 6 Ó Õ Ô Ò
P Q R S 7 ß
T U V 8 Ú Ü Û Ù
1. From a text entry screen, press QNotes (left
softkey).
2. Select a message and press r.
WXY Z 9
+ - 0 * / \ [ ] = > < # §
Space Shift Caps Lock
Back
Tip: To add a quick note after you have already started
entering a message, press /> Insert > Insert QNotes,
and select a message.
18
When none of these icons appear, letters typed are
lowercase. Scrolling up or down after typing a letter in
Alpha mode changes the case of the letter (uppercase
or lowercase).
Note: Quick Notes preset messages make composing text
messages easier by allowing you to enter quick
messages, such as “Meet me at,” “Let’s get lunch,” or a
customized message of your own.
Note: When creating a text message, you may not be able to
make a letter uppercase by scrolling up, depending on
the type of text message and the text entry mode.
Special Function Keys
Some of the phone’s keys assume different functions
while in Alpha or Word mode.
Your phone automatically makes the first letter of a
sentence uppercase.
Spaces
Punctuation
Press #to enter a space.
Capitalization
Press 1or 0to insert punctuation. Continue to press
the key to view the list of symbols available through that
key. Pause to select a symbol.
When you press and hold the #key, it acts as a
three-way toggle. Press and hold #to make the next
letter typed uppercase (shift), to make all subsequent
letters typed uppercase (caps lock), or to go back to
lowercase letters.
Note: Additional punctuation symbols are available in
Symbols mode.
These icons appear:
Shift is on.
Ror U
Sor V
Caps lock is on.
19
Using a Remote Direct Connect Button
Accessories
If you are using a headset or other optional accessory
with a remote Direct Connect button, you can use the
remote Direct Connect button for phone calls, Direct
Connect calls, and Group Connect calls.
Your phone comes with the following accessories:
ⅷ A Li-Ion battery and charger.
ⅷ A128K SIM card.
For phone calls, use the remote Direct Connect button
to answer calls, switch between calls, and end calls.
Hold the remote Direct Connect button for less than
two seconds to answer calls and switch between calls.
Hold the remote Direct Connect button for more than
two seconds to end calls.
Various accessories are available for use with your
MOTOROLA BRUTE, including cases, vehicle power
chargers, data cables, hands-free accessories, and
more.
To order additional accessories, go to www.nextel.com
or call1-866-866-7509. You can also contact your
Nextel Authorized Representative or stop by any Sprint
Store. For information on Sprint Store locations, go to
For Direct Connect calls and Group Connect calls, use
the remote Direct Connect button as you would the
Direct Connect button on your phone.
When using a headset, the Direct Connect button on
your phone works the same way as when you are not
using a headset. Direct Connect and Group Connect
sounds will be heard through the headset.
20
ⅷ Digital Wireless Phone Calls offer clear calls and other
services, such as missed call notification, Three-Way
3. Making and Answering
Calls
ⅷ Direct Connect Calls allow two-way radio
communication with another Direct Connect user
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ⅷ Group Connect Calls allow coast-to-coast two-way
radio calling to up to 20 Nextel Direct Connect
ⅷ Nextel Direct Send allows you to send contact
information in Direct Connect and Group Connect
calls and send pictures in Direct Connect calls
ⅷ Talkgroup Calls allow two-way radio calling to up to
100 Nextel Talkgroup customers simultaneously
Types of Calls
Note: To learn more about the differences between Nextel
Group Connect calls and Talkgroup calls, please see
With the Nextel National Network, Nextel Direct
Connect, and your MOTOROLA BRUTE, you have the
following traditional wireless phone and Nextel Direct
Connect services available to you:
ⅷ Nextel Direct Talk allows for two-way radio
communication “off the network” between two or
21
more phones equipped with this capability
Answering Calls
1. Make sure your phone is on.
Phone Calls
Note: When your phone is off, calls go directly to voicemail.
2. Press `to answer an incoming call.
Making Calls
Depending on your settings, you may also answer
incoming calls by opening the phone or pressing any
information.
Placing a traditional wireless phone call from your
MOTOROLA BRUTE is as easy as making a call from
any landline phone.
Tip: When the phone is closed, you can answer a call by
pressing the speaker button ()) on the top of the phone.
To set the phone to answer and end calls by opening
and closing the phone, press /> Settings > Phone
Calls > Flip Activation and set Flip To Ans and Flip To
End to On.
1. Make sure your phone is on.
2. Enter a phone number from standby mode and
press `. (If you make a mistake while dialing,
press Delete [right softkey] to erase the numbers.)
3. Press @when you are finished.
Your phone notifies you of incoming calls by any
combination of ringing or vibrating, the indicator light
flashing, the backlight illuminating, or the screen
displaying an incoming call message.
Tip: To redial your last outgoing call, press and hold ,.
You can also place calls from your phone by using
If the incoming call is from a number stored in your
Contacts, the entry’s name is displayed. The caller’s
phone number may also be displayed, if available.
22
Ending a Call
Emergency Calls
ᮣ
To end a call, press @or close the phone.
Your phone supports emergency calling. Emergency
phone calls can be made even when your SIM card is
blocked or not in your phone.
Missed Phone Calls
Missed phone calls are forwarded to voicemail. When
you do not answer an incoming call, you will see a
Missed Call notification.
ᮣ
Dial 911and press `to be connected to an
emergency response center. If you are on an active
call, you must end it before calling 911.
To display a Missed Call entry from the notification screen:
When you make an emergency call, your phone’s GPS
Enabled feature can help emergency service
personnel find you, if you are in a location where your
phone's GPS antenna has established a clear view of
the open sky and your local emergency response
center has the equipment to process location
particularly “IMPORTANT: Things to Keep in Mind” on
feature. Because of the limitations of this feature, always
provide your best knowledge of your location to the
emergency response center when you make an
emergency call.
ᮣ
Press View (left softkey). (To dial the phone
number, press `after displaying the entry.)
To display a Missed Call entry from standby mode:
1. Press `or /> Recent Calls.
2. Highlight an entry and press r.
23
In-Call Options
Important: Always report your location to the 911 operator
when placing an emergency call. Some
designated emergency call takers, known as
Public Safety Answering Points (PSAPs) may not
be equipped to receive GPS location information
from your phone.
Press /during a call to display a list of available
in-call features. To select an option, highlight it and
press r. The following options may be available:
ⅷ Hold to place the call on hold.
Emergency calls cannot be placed while the
keypad is locked.
ⅷ 3 Way to initiate a three-way call.
ⅷ Use Bluetooth to switch from the phone’s microphone
to a Bluetooth device.
If you have not registered on the network,
emergency calls cannot be placed while your
SIM card is in your phone.
ⅷ 2nd Call to place a second call.
ⅷ Contacts to display your Contacts list.
ⅷ Recent Calls to display Recent Calls list.
ⅷ My Info to display your phone’s Information.
ⅷ Memo to display the phone’s electronic notepad.
ⅷ Datebook to enter a datebook event.
ⅷ Messages to create a message.
If you are bringing your phone number to Nextel
from your previous carrier, you may receive a
temporary telephone number while your Nextel
phone is being programmed with your
permanent phone number. If you make a call to
911 and the call fails, the 911 emergency
response center will not be able to call you back
on your Nextel phone if in the meantime, your
Nextel phone has been programmed with your
permanent telephone number. If the call is
disconnected before location and details have
been provided, call 911 again and advise that you
were disconnected.
ⅷ Store to store a new contact.
ⅷ Record to record the phone call.
ⅷ GPS to enter the GPS application.
ⅷ In Call Setup to modify the in-call features.
24
To view Call Details and Call Info:
1. Select a recent call.
Speakerphone
ᮣ
Press )or Speaker (right softkey) during a call to
route the phone’s audio through the speaker or the
earpiece.
2. Press rto view the Call Details.
3. Press ragain to view the Call Info.
WARNING: Because of higher volume levels, do not place the
phone near your ear during speakerphone use.
Saving a Phone Number
Mute
1. Enter a phone number and press /.
ᮣ
Press Mute (left softkey) during a call to mute the
microphone. Press Unmute (left softkey) to unmute
the microphone.
2. Highlight Store Number and press r.
3. To store a new entry, highlight [New Contact] and
press rto add a new entry.
– or –
End-of-Call Options
Search for an existing contact name and press r
to save the new number.
After you receive or make a call, the call duration is
briefly displayed. You are then automatically taken to
the Recent Calls list.
4. Enter or edit information as necessary and press
Save (left softkey) to save the Contact.
To save a number that is not in your contacts:
For more information about Contacts, see “8. Contacts”
ᮣ
Highlight an entry and press Save (left softkey).
25
Finding a Number
Note: You can have multiple pauses in a phone number and
combine waits and pauses.
To find Contacts entries, you can either scroll through
the list using your navigation key or you can search
Contacts entries by name.
To dial or save phone numbers with pauses:
1. Enter the phone number.
1. Press /> Contacts.
2. Press and hold *until the letter P appears. The P
represents a three-second pause. For a longer
pause, press the letter P more than once. Each P
represents a three-second pause.
2. Press Search (left softkey).
3. Enter the first few letters of a Contact's name and
press r. (The first contact entry that matches the
entered text will be highlighted.)
– or –
Press and hold *until the letter W appears. The
W means your phone waits before dialing further. A
message appears asking about sending the rest of
the digits.
4. To display the Contacts entry, press r. To dial the
entry's default phone number, press `.
Phone Numbers With Pauses
3. Enter additional numbers.
4. Press `to dial the number.
– or –
You can dial or save phone numbers with pauses for
use with automated systems, such as voicemail,
conference call, or credit card billing numbers.
There are two types of pauses available on your phone:
Press /> Store Number to save the number in
your Contacts.
ⅷ Wait sends the next set of numbers when prompted.
ⅷ Pause automatically sends the next set of numbers
after three seconds.
Note: When dialing a number with a wait, press Yes (left
softkey) to send the next set of numbers.
26
2. Say a voice name. Your phone plays the name
Making a Call From Contacts
back to you.
1. Press /> Contacts.
3. The call is placed automatically.
2. Highlight an entry and press `to dial the default
phone number.
Tip: To stop a phone call from being completed,
press @.
– or –
To dial another number from the entry, highlight
the name, press the navigation key right or left until
the correct number type appears, and then
press `.
Making a Phone Call While in a Direct
Connect Call
Pressing `while in an active Direct Connect lets you
initiate a phone call to the other person if their mobile
phone number is stored in Contacts.
Making a Call From Recent Calls
1. Press `or /> Recent Calls.
1. While in a Direct Connect conversation press `.
(You will see a Start Call To: prompt.)
2. Highlight an entry and press `.
2. Press Yes (left softkey) or press rto switch from
the Direct Connect call to a phone call.
Making a Phone Call Using a Voice Name
If you have created a voice name in Contacts (see
page 99), say the voice name into your phone to enter
the number.
Speed Dialing
Each phone number stored in Contacts is assigned a
Speed Dial number, which you can use to call that
number. You can store up to 600 numbers in your
phone’s speed dial memory.
1. Press and hold
s
until a prompt appears telling
you to say the voice name.
27
1. Enter a speed dial number and then press #.
2. Press `to dial the number.
To use Turbo Dial® for speed dial locations 1–9:
ⅷ Group Connect® allows nationwide Direct Connect
calling to up to 20 other Direct Connect users at
ⅷ TalkgroupSM allows Direct Connect calling to up to
100 Nextel subscribers in the same Direct Connect
network. See “Talkgroups” on page 39.
ⅷ Nextel Direct TalkSM lets you establish off-network,
two-way radio communication between two or more
Nextel Direct Talk-capable phones. See “Direct Talk”
ᮣ
Press and hold the appropriate key for
approximately two seconds. The display confirms
that the number has been dialed when it shows
“Calling...”.
Redialing the Last Number
Connect services. Pricing for each of these services is
based on your service contract.
ᮣ
Press and hold `.
Nextel Direct Connect
Making Direct Connect Calls
Nextel offers the following Nextel Direct Connect®
services:
ⅷ Direct Connect® allows instant two-way radio
communication with another Direct Connect user
anywhere on the Nextel National Network (U.S.).
2. Press and hold the Direct Connect (DC) button on
the left side of your phone. Begin talking after your
phone emits a chirping sound.
ⅷ International Direct Connect allows Direct Connect
calling to and from select countries.
3. Release the DC button to listen.
28
A Direct Connect call ends automatically after there is
no activity on the call for several seconds.
Using Just the Member ID
If you are contacting someone sharing your network
and area IDs, you only need to enter the member ID
(the last part of the number).
Dialing Direct Connect Numbers
Every Direct Connect number has three parts:
ⅷ An area ID.
1. Enter a member ID.
2. Press and hold the DC button.
ⅷ A network ID.
ⅷ A member ID.
Making Direct Connect Calls From Contacts or
Recent Calls
An asterisk separates each part (for example:
999*999*9999). When you enter a number containing
all three parts, you must separate them with asterisks.
make calls.
Note: The number of digits in each part of a Direct Connect
number may vary. For example, your Direct Connect
number may be formatted as 999*999*9999, while
another valid number may appear as 555*555555*55.
1. Press /> Contacts or Recent Calls.
2. Highlight an entry and then press and hold the DC
button to call the entry’s Direct Connect number.
If you are calling or saving a Direct Connect number for
a Sprint phone with Direct Connect capabilities, the
Direct Connect number may be the same as the
wireless phone number. When dialing or saving the
Direct Connect number, insert asterisks in place of
hyphens (913*555*1234).
Tip: You can make Direct Connect calls while viewing entry
details on either list. Display the entry details or My Info
from another phone (in Recent Calls) and press and hold
the DC button.
Tip: When you store a Direct Connect number in Contacts, be
sure to include the entire number, including the asterisks.
29
Making Direct Connect Calls Using a Voice Name
Group Connect
If you have created a voice name in Contacts, say the
voice name into your phone to enter the number.
A Group Connect call is similar to a Direct Connect call
to one user, but is made to multiple Direct Connect
subscribers at once. You can create Groups from your
phone and call up to 20 other Group Connect-
compatible phones* anywhere on the Nextel National
Network. You can create a Group for one-time use or
store it to Contacts so you can call it at any time.
1. Press and hold the speaker button (s) until a
prompt appears telling you to say the name.
2. Say the name. Your phone plays the name back to
you.
3. Press and hold the DC button.
Answering Direct Connect Calls
Note: In order to store Groups to your MOTOROLA BRUTE,
you must use the 128K SIM card that came with your
phone. The 128K SIM card is labeled “Nextel 600
Contcs & 25 Grps”. With this SIM card, a maximum of
25 groups can be added to your MOTOROLA BRUTE.
Group entries created with your MOTOROLA BRUTE
may not be readable by older iDEN SIM-based phones.
When you receive a Direct Connect call, your phone
emits a tone or vibrates. You then hear the voice of
your caller.
1. Wait for the caller to finish speaking.
2. Press and hold the DC button. Continue as you
would on any Direct Connect call.
Making Group Connect Calls
3. Press @to end the call.
1. From Contacts or the Recent Calls list, highlight or
select a Group.
A Direct Connect call ends automatically after there is
no activity on the call for several seconds.
2. Press the DC button
30
.
record a Group name. When you have finished,
press Back (right softkey).
Tip: You can also start a Group Connect call by entering or
selecting a Direct Connect number. See “Starting a
6. Press Save (left softkey).
Adding Group Members
Answering Group Connect Calls
You can add Group members that have a Direct
Connect number and Group Connect-compatible
phone to your Group by selecting them from Contacts,
the Recent Calls list, Memo, or by manually entering
the Direct Connect number from your keypad. You can
also add all members in an existing Group to another
Group by selecting the Group name from Contacts.
ᮣ
Proceed as if answering a Direct Connect call from
one user. Only one person at a time may speak on
a Group Connect call.
Creating Groups in Contacts
1. Press /> Contacts.
To add Group members from Contacts, the Recent Calls
list, or Memo:
2. Select [New Group].
3. To assign a name to the Group, enter the name.
1. While creating a Group, select [Add Member].
Note: If you do not assign a name, the Group is named
“Group” followed by the number of members in the
Group. For example, “Group (8)” is a group with eight
members.
Note: To move between Contacts, the Recent Calls list, and
Memo, scroll left or right.
2. Highlight desired entries and press r. A
checkmark appears next to each selected
member.
Note: To deselect a member, highlight it and press r.
5. To create a voice name for the Group (optional),
select [Options] > Voice Name. Follow the prompt to
31
3. Press Done (left softkey) and then press Save (left
softkey) to save the group.
To add Group members manually from the keypad:
1. While creating a Group, select [Add Number].
2. Enter the Direct Connect number.
4. To save the Group, press /> Store Group.
– or –
To call without saving, press Done (left softkey).
5. To make the call, press the DC button.
3. Press rand then press Save (left softkey).
Removing Members or Groups
Starting a Group Connect Call With a
Direct Connect Number
To remove a member from a Group:
1. From Contacts, highlight a Group and press Edit
1. Press /> Push To Talk > Direct Connect, select
entries for a Group Connect call, and go to step
four. (To add members or numbers from Recent
Calls or Memo, scroll left or right.)
(left softkey).
2. Highlight a member and press />
Remove Member.
– or –
3. Press Save (left softkey)
.
From standby mode, enter a Direct Connect
number.
Note: You can also select Remove All Members however,
you will have to add at least two new members to save
the edited Group.
– or –
From Contacts or Recent Calls, highlight an entry
containing a Direct Connect number.
To delete a Group from Contacts:
1. From Contacts, highlight a Group.
2. Press /> Delete Group.
2. Press /> New Group or Call New Group.
32
3. Press Yes (left softkey).
2. Select a number or member to store.
3. Add more information to the entry (optional).
4. Press Save (left softkey).
Storing Groups
To store a group to Contacts from the Recent Calls list:
To store a member from an active call:
1. From the Recent Calls list, select a Group and
press Save (left softkey).
1. During an active Group Connect call, press />
Store Number.
2. Add more information to the entry (optional).
3. Press Save (left softkey).
2. Select a number or member to store.
3. Add more information to the entry (optional).
Note: You cannot record a voice name during an active call.
To store a group to Contacts from an active call:
1. During an active Group Connect call, press />
Store Group.
4. Press Save (left softkey).
2. Add more information to the entry (optional).
Group Connect Call Information
Note: You cannot record a voice name during an active call.
While you are in a Group Connect call, the following
appears on the screen:
3. Press Save (left softkey).
ⅷ The name of the Group.
Storing Members of Groups
ⅷ The name or the Direct Connect number of the
person speaking.
To store a member from the Recent Calls list or within
Contacts:
ⅷ The number of members who are participating in the
Group Connect call.
1. Display a Group and press /> Store Number.
33
Group Connect Call Details
Nextel Direct Send
During a Group Connect call, you can view details
about the other group members, such as their name or
Direct Connect number, and their status on the call.
Nextel Direct Send lets you use Direct Connect calls to
exchange pictures, My Info, contact information, and
Groups with other phones that have this capability.
To view Group Connect call details:
Nextel Direct Send cannot be used during Talkgroup
calls. Pictures cannot be sent in Group Connect calls.
ᮣ
Press Details (left softkey).
In the Details view, these icons appear next to member
names or Direct Connect numbers:
Sending a Picture
When you send a picture using Nextel Direct Send, the
picture appears on the display of the receiving phone,
and is saved by that phone.
The member of the Group who is speaking.
F
A member of the Group who is active on the
Group Connect call, but not speaking.
E
Sending a Picture During a Call
A member of the Group who has exited the
call.
D
You can send a picture at any time during a Direct
Connect call, whether you made or received the call.
(Additional charges may apply.)
A member of the Group who could not be
reached on the Group Connect call.
H
You cannot talk or listen on a Direct Connect call while
a picture is being transmitted. Other activities, such as
searching for a picture, do not prevent you from talking
or listening.
A member of the Group whose status is
unknown.
G
34
To send a picture during a call:
Tip: When a person sends you My Info from his or her phone,
including his or her Direct Connect number and IP
address, you can then easily store this information to
Contacts from the Recent Calls list.
1. While in a Direct Connect call, press Picture (right
softkey). A list of pictures that can be included in a
Direct Connect call appears.
To start a call by sending a picture:
2. Select a picture and press the DC button to send it.
1. Press /> Multimedia > Media Center and then
3. Wait while the picture is transmitted. The Direct
Connect call is temporarily interrupted while a
picture is transmitted.
highlight or select a picture.
2. Press /> Send Via... > Direct Send.
4. When prompted, press the DC button to resume
3. Select A Contact or A Recent Call. These names
have Direct Connect numbers and IP addresses
stored.
the Direct Connect call.
Note: The first time you send a stored picture after turning the
phone on, the message Picture Fees May Apply
appears and you are prompted to respond. Press Yes
(left softkey) to send the picture. Press No (right softkey)
to cancel.
4. Select a name and press the DC button to send
the picture.
5. When prompted, press the DC button to resume
the Direct Connect call.
Starting a Call by Sending a Picture
Receiving a Picture
You can start a call by choosing a stored picture from
the Media Center.
When someone sends you a picture using Nextel
Direct Send, your phone emits a tone or vibrates and a
message appears on the display asking you to accept
the picture.
To do this, you must have the recipient’s Direct Connect
number and IP address stored in your Contacts.
35
Pictures you receive are saved to your phone’s memory
and are accessible through the Media Center.
Tip: To stop the transmission before it is finished, press
Cancel (right softkey).
When you receive a picture, it appears every time you
are in a Direct Connect call with the person who sent it
unless you delete the picture from the Media Center.
This occurs for the last 20 people who sent you
pictures.
Setting Picture Capability
To turn your phone’s ability to send and receive pictures in
Direct Connect calls on or off:
1. Press /> Push To Talk > PTT Options > On/Off
Settings.
To accept a picture:
1. When you see the message asking you to accept
the picture, press Yes (left softkey). (To decline the
picture press No [right softkey].)
2. Select Pictures and press rto check or uncheck
the box.
3. Press Done (left softkey) to save the setting.
2. Wait while the picture is transmitted. The Direct
Connect call is temporarily interrupted while a
picture is transmitted.
This setting does not affect your phone’s ability to send
and receive My Info or contact information.
3. When prompted, press the DC button to resume
the Direct Connect call.
Sending My Info and Contact Information
When you send My Info or contact information using
Nextel Direct Send, the information you send appears
on the display of the receiving phone. After the call, the
information appears on that phone’s Recent Calls list.
Note: The first time you accept a stored picture after turning
the phone on, the message Picture Fees May Apply
appears and you are prompted to respond. Press Yes
(left softkey) to accept the picture. Press No (right
softkey) to cancel.
36
4. When you are finished, press Done (left softkey).
To control whether your information is sent automatically:
1. Press /> Tools > My Info.
Sending My Info
You can control what portion of the information in My
Info is sent and whether it is sent automatically in every
Direct Connect call or only when you choose to send it.
2. Press /> Direct Send Setup > Auto Send.
Tip: When you send My Info, certain information, such as your
email address or fax number, cannot be included. To
send complete contact information, create an entry for
yourself in Contacts and send it.
3. Select On to send your information automatically,
or Off to send your information only when you
choose to send it.
Note: When you receive your phone, it is set to send your
The information your phone sends always includes My
Name and Direct Connect.
information automatically.
To send My Info during a call:
It may include Line 1, Line 2, Carrier IP, Direct Connect,
and Group ID depending on the options provided by
your service provider and how you set your sending
options.
1. While in a Direct Connect call, press />
Direct Send My Info.
2. When Ready To Send appears, press the DC button
to send the information.
The default setting is Line 1 only.
To change which fields are sent:
To start a call by sending My Info:
1. Press /> Tools > My Info.
2. Press /> Direct Send My Info.
1. Press /> Tools > My Info.
2. Press /> Direct Send Setup > Info To Send.
3. A checkmark appears next to the fields that will be
sent. To add or remove the checkmark, select the
field.
3. Enter a Direct Connect number or press Browse
(left softkey) and select a number from Contacts,
Recent Calls, or Memo.
37
4. When Ready to Send appears, press the DC button
2. Press /> Send Via... > Direct Send.
to send the information.
Note: If the Contacts entry you scrolled to is a Group, you may
be prompted to allow yourself to be a part of the group
being sent. Press Yes (left softkey) to become part of
the group.
Sending Contact Information
You can send contact information by selecting a
Contacts entry.
3. Enter a Direct Connect number or press Browse
(left softkey) and select a number from Contacts,
Recent Calls or Memo.
Contacts entries that contain only addresses cannot be
sent. When Contacts entries are received, they do not
include ring tones or pictures.
4. When Ready To Send appears, press the DC button
to send the contact information.
To send contact information during a call:
1. While in a Direct Connect call, press />
Receiving My Info or Contact Information
Contacts.
When you receive My Info or contact information from
another phone, an icon appears on the display.
2. Highlight a Contacts entry and press />
Send Via... > Direct Send.
My Info
3
2
Note: If the Contacts entry you scrolled to is a Group, you may
be prompted to allow yourself to be a part of the group
being sent. Press Yes (left softkey) to become part of
the group.
Contact Information
To view the information while still in the Direct Connect call:
Press /> View Contact.
3. When Ready to Send appears, press the DC button
to send the contact information.
ᮣ
You can also view My Info from other phones on the
To start a call by sending contact information:
1. From Contacts, highlight or select an entry.
38
2. To include yourself in the Group, press Yes (left
softkey). To exclude yourself, press No (right
softkey).
Sending Groups Using Direct Send
You can send a Group using Nextel Direct Send so that
the person who receives the Group can use the list.
3. Select Direct Send.
To send a Group from the Recent Calls list:
4. Enter a Direct Connect number or press Browse
(left softkey) and select a number from Contacts,
Recent Calls or Memo.
1. From Recent Calls, highlight a Group and press
/> Send Group.
2. To include yourself in the Group, press Yes (left
softkey). To exclude yourself, press No (right
softkey).
5. When Ready To Send appears, press the DC button
to send the Group.
The Group will appear in the Recent Calls list on the
phone to which you sent the Group.
Note: If you choose to include yourself and the Group already
contains 20 members, you will be prompted that the list
is full. You will be excluded from the list.
Talkgroups
3. Enter a Direct Connect number or press Browse
(left softkey) and select a number from Contacts,
Recent Calls, or Memo.
A Talkgroup is a predetermined group of Direct
Connect users, created by an account administrator.
Talkgroups can contain up to 100 members.
4. When Ready To Send appears, press the DC button
to send the contact information.
Difference Between Group Connect and
Talkgroup Calls
To send a Group from Contacts:
1. From Contacts, highlight a Group and press />
Send Via....
In a Group Connect call, you or another caller
determines who can participate in the call. By contrast,
39
participation in a Talkgroup is determined by an
administrator. Here are the ways Group Connect and
Talkgroup calls differ.
1. Press Contacts (right softkey) and highlight a
Talkgroup.
2. Press Join (left softkey).
You can now receive communications from other
members of this Talkgroup.
Group
t
Talkgroup
Group Icons
Geography
r
You will hear all active Talkgroup conversations on your
phone. To silence them, press /> Push To Talk >
PTT Options > Tkgrp Silent and then select On.
Nationwide
Limited to local
market and network
(fleet)
21 (including
originator)
100
Maximum
Group Size
Adding More Talkgroups
You can be included in additional Talkgroups by doing
one of the following:
Dynamically,
via your phone administrator using
Talkgroup
Predefined, via Nextel
Setup
must be an account administrator to use Talkgroup
Management.
Management
Voice
Activated
Dialing
Yes
No
ⅷ Contacting your Nextel Sales Representative at the
time of activation.
Making Talkgroup Calls
Joining a Talkgroup
1. Press
and then enter the Talkgroup number.
#
To participate in a Talkgroup, the account administrator
must first add you to the membership and then you
must “join” the Talkgroup.
– or –
40
Select the Talkgroup from Contacts or the Recent
Calls list.
2. When “Ready to Alert” appears, press the DC
button to send the Call Alert.
2. Press the DC button and continue as if making a
Direct Connect call.
Note: You can send a Call Alert from Recent Calls or
Contacts. Select a Direct Connect number and
continue as explained above.
Receiving Talkgroup Calls
Responding to a Call Alert
ᮣ
Answer it as you would a regular Direct Connect
call. Only one person at a time may speak on a
Talkgroup call.
During and immediately after a Talkgroup call ends,
press Options (right softkey) to display any available
options.
To answer a Call Alert:
ᮣ
Press the DC button to make a Direct Connect call
to the sender.
To clear a Call Alert:
Press Clear (right softkey).
To store a Call Alert in the Call Alert queue:
Press Queue (left softkey).
Call Alerts
ᮣ
Call Alerts let you notify others that you want to
communicate with them using Direct Connect. When a
user receives a Call Alert, the phone sounds a tone
and displays your name or Direct Connect number.
ᮣ
Note: The Recent Calls list also stores Call Alerts you have
received. They appear as Direct Connect calls. Call
Alerts remain in your Recent Calls list until you delete
them or until they reach the end of the list.
Sending Call Alerts
1. Enter a Direct Connect number and press Alert
(left softkey).
41
This removes the Call Alert from the queue.
To send a Call Alert to the sender:
Using the Call Alert Queue
When you queue a Call Alert, it remains in the Call Alert
queue until you make a Direct Connect call to the
sender or delete it.
1. Press /> Push To Talk > Call Alert.
2. Highlight a Call Alert and press Alert (left softkey).
Ready to Alert appears on the display.
Viewing Call Alerts
3. Press the DC button until Alert Successful appears
1. Press /> Push To Talk > Call Alert.
2. Scroll through the list.
on the display.
Deleting Call Alerts
Viewing Call Alert Date and Time
1. Press /> Push To Talk > Call Alert.
2. Select a Call Alert and press r.
To delete a Call Alert from the queue:
1. From the Call Alert queue, highlight a Call Alert
and press /> Delete.
Responding to Call Alerts in the Queue
2. Press ror press Yes (left softkey) to confirm.
To delete all Call Alerts from the queue:
After you queue a Call Alert, you can respond to it by
making a Direct Connect call to the sender or sending
a Call Alert to the sender.
1. From the Call Alert queue, press /> Delete All.
2. Press ror press Yes (left softkey) to confirm.
To make a Direct Connect call to the sender:
1. Press /> Push To Talk > Call Alert.
2. Highlight a Call Alert and press the DC button to
begin the call.
42
3. To edit a message before sending it, press
/> Edit
Call Status and Completion
After a failed incoming or outgoing Direct Connect call
or Call Alert, you can send a message to the caller or
intended recipient.
Direct Talk
To set up a message for incoming or outgoing calls:
Nextel Direct Talk allows for two-way radio
communication “off the network” between two or more
phones equipped with this capability. This feature is
useful in areas without network coverage.
1. Press /> Settings > Advanced > Call Completion
> Incoming Call or Outgoing Call.
2. In the Send Msg field, select Off, Ask First, or
Automatic.
You can make:
ⅷ Code calls – two-way radio calls conducted off the
network and using open channels and codes. In
these calls, anyone using your same channel and
code can hear your conversation.
3. Select Message and create a message to be sent,
or press QNotes (left softkey) and select a
predefined message.
4. Press rand then press Back (right softkey).
ⅷ Private calls – two-way radio calls conducted off the
network and using the wireless phone numbers of
the participants. In these calls, others using the same
channel cannot listen in.
To send a message after receiving or making a call:
1. After a failed incoming or outgoing Direct Connect
call, within five seconds, Send Text Message To will
appear.
When using Direct Talk mode, the two phones should
be a minimum of six feet apart to maximize
performance and improve transmission range. You can
only make Direct Talk calls to users located within your
2. Press Yes (left softkey) to send your predefined
message or press No (right softkey) to cancel.
43
range. This varies according to terrain, man-made
structures, and atmospheric conditions.
Code Direct Talk Calls
To make Direct Talk Code calls, both parties must be
on the same channel and code and have their phones
set to Direct Talk. Anyone within range who is set to the
same code and channel can hear all conversations.
Most traditional phone features are not available in
Direct Talk mode, including on-network phone calls;
Direct Connect, Group Connect, Talkgroup calls, and
Call Alerts; data services; messaging; call timers; and
call forwarding.
To set a channel and code:
1. In Direct Talk mode, press Edit (left softkey) >
Channel, and then select a channel.
Setting Your Phone to Direct Talk
Before you and another caller can use Direct Talk, both
of your phones must be set to Direct Talk mode.
2. Select Code and select a code.
3. Press Back (right softkey) to return to the Direct Talk
standby screen.
1. Press /> Push To Talk > Direct Talk.
2. Select Go To Direct Talk.
Making and Receiving Code Calls in Direct Talk
Mode
After a few seconds, your channel and code appear on
the display screen. Your phone displays the last
channel and code used for Direct Talk.
ᮣ
In Direct Talk mode, press and hold the DC button.
Your phone displays Transmitting, along with the
channel and code selected.
To return to network mode from Direct Talk:
1. Press /> Push To Talk > DT Options.
2. Select Exit Direct Talk.
The tone emitted from your phone when making a
Direct Talk call sounds different from the tone heard on
Direct Connect calls conducted on the network.
After a few seconds, your phone returns to network
service.
44
If you receive an error message, this means:
ⅷ There may be no parties on your channel or code.
ⅷ You are out of range.
Note: You do not need to set your phone to Private Only to
receive Private calls. If you are on the same channel as
your caller, you can receive Private Direct Talk calls.
When you receive a Code call using Direct Talk, your
phone displays Receiving, along with the channel and
code selected. Reply as on a Direct Connect call.
Making a Private Direct Talk Call
You can make Private Direct Talk calls to any person on
your same channel. You do not need to set your phone
to Private Only.
Private Direct Talk Calls
To make a private Direct Talk Call:
Private Direct Talk allows you to silence all the calls on
a channel that are not directed specifically at you. To
do this, you must first set your phone to Private Only.
1. In Direct Talk mode, enter a ten-digit wireless
phone number. (You can also select a number
from Contacts or Recent Calls.)
To set your phone to Private Only:
2. Make the call in the same way you make a regular
Direct Connect call.
1. In Direct Talk mode, press Edit (left softkey) >
Code > Pvt Only.
If you receive an error message, it means:
2. Press Back (right softkey) to return to the Direct Talk
standby screen.
ⅷ You may not be using a valid wireless phone
number.
To reach you, other Direct Talk callers must be on your
same channel and dial your ten-digit wireless phone
number to reach you.
ⅷ The person that you are trying to reach may not be in
Direct Talk mode.
ⅷ The person that you are trying to reach is set to a
different channel, or is out of range.
45
Receiving All Calls on a Channel
Making Emergency Calls While in Direct
Talk Mode
You can set your phone to receive all Direct Talk
transmissions that are within range and set to the same
channel. Do this by selecting Receive All, instead of a
code.
If you attempt to make an emergency 911 call while in
Direct Talk mode, your phone automatically exits Direct
Talk mode and attempts to find a network signal.
You cannot initiate a call when the code is set to
Receive All. If you press the DC button to initiate a
Direct Connect call and your code is set to Receive All,
you receive an error message.
If you are out of network coverage, your phone cannot
make an emergency 911 call until you return to a
network coverage area. You must wait until the phone
reconnects to a network before attempting to make an
emergency 911 call.
To set the code to Receive All:
1. In Direct Talk mode, press Edit (left softkey) >
Code > Receive All.
2. Press Back (right softkey) to return to the Direct Talk
standby screen.
46
Message Center
4. Service Features:
The Basics
The message center manages your messages. You
can listen to or view voicemail messages, Multimedia
Messaging Service (MMS) messages (which include
most phone-to-phone text messages), Net alerts, and
SMS text messages in the message center.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ The message center also lets you create and send
MMS messages, including phone-to-phone text
messages. It stores messages you have sent and lets
you save drafts of messages you are creating.
Accessing the Message Center
ᮣ
Press /> Messages.
Message Center Options
After accessing the message center, select an option:
ⅷ [Create Message] — begin creating an MMS
message.
ⅷ Voice Mail — access received voicemail messages.
ⅷ Inbox — access received MMS and SMS messages.
47
ⅷ Drafts — access MMS messages you have created
and saved but not sent.
ᮣ
To dismiss the message notification, press Later
(right softkey).
ⅷ Outbox — store MMS messages that were not sent.
ⅷ Sent Items —access MMS messages you have sent.
ⅷ Net Alert — access alerts that you receive from Nextel.
If you dismiss the notification, the message is not
deleted. You can access it through the message center.
If you are not on a phone call when you receive a
message, your phone sounds a notification tone every
30 seconds until you access the message, you dismiss
the notification, or the alert time-out expires.
Receiving Messages
When you are on a phone call, you can receive
message notifications for all types of messages except
MMS messages. For other types of messages, your
phone may sound a notification tone during the call or
after you end the call, depending on how you set your
notification options.
When you receive a voicemail message, Multimedia
Messaging Service (MMS) message, text message
(SMS), or Net alert, you have two ways to access the
message:
ⅷ Respond to the message notification that appears
when the message is received.
For information on notification options, see “Setting
ⅷ Dismiss the message notification and access the
message later through the message center.
Retrieving Your Messages
Message Notifications
1. Press /> Messages.
When you receive a message, your phone notifies you
with text on the display and a notification tone or
vibration. You can access the message or dismiss the
notification.
2. Highlight a message type and press r.
48
access your voicemail box. The system will prompt you
to enter your password. Enter the last seven digits of
your Nextel PTN. For example: 5557777. This is your
temporary password. Follow the system instructions to
complete your mailbox setup.
Voicemail
Tip: To receive voicemail messages, you must first set up your
voicemail box.
If you are bringing your phone number from another
carrier, we suggest you set up your voicemail box after
the number you brought to Nextel is active on your Nextel
phone and your temporary phone number is deactivated.
If you set up your voicemail box prior to this, all messages
and all settings (including your greeting and password)
will be lost when the number you have brought to Nextel
becomes active.
You are in the main voicemail menu when you hear the
voicemail system options.
For details on using your voicemail, follow the audio
prompts provided by the voicemail system.
Playing Messages
ᮣ
ᮣ
When you receive a new voicemail message, you
can either listen to it immediately by pressing Call
(left softkey), or later by pressing Back (right
softkey).
Setting Up Your Voicemail Box
Using your MOTOROLA BRUTE, dial your ten-digit
Nextel Personal Telephone Number (PTN). For
example: 7035557777. Follow the system instructions
to create a new four- to seven-digit password, record
your name, and record a greeting. When the system
says, “Thank you for using Nextel Voicemail,” your
mailbox is set up.
To listen to your voicemail messages after
dismissing the onscreen prompt, press />
Messages > Voice Mail. You will be connected to
your voicemail box.
If you are setting up your voicemail from a phone other
than your MOTOROLA BRUTE, dial your ten-digit
Nextel PTN. When you hear the greeting, press *to
49
Creating and Sending Messages
Multimedia Messages (MMS)
Each message you create may contain the following
fields:
Multimedia Messaging Service (MMS) lets you send
and receive messages that may include text, pictures,
and audio recordings.
ⅷ To — the phone numbers or email addresses of one
or more recipients.
Your PTN is your ten-digit Nextel Personal Telephone
Number.
ⅷ Message — the body of the message. This may
include text, pictures, ring tones, or voice records.
ⅷ Subject — the subject line.
Note: Most common phone-to-phone text messages are sent
and received as MMS messages on your MOTOROLA
BRUTE. Text messages sent from other phones or
mobile devices to your phone number arrive as MMS
messages.
ⅷ Attach — one or more attachments. These may be
pictures, ring tones, or audio files, including voice
records that you create while creating the message.
ⅷ Cc — the phone numbers or email addresses of
additional recipients.
Accessing MMS Messages
ⅷ Auto Replies — lets you insert replies the recipient can
choose from when replying to your message, if the
recipient’s phone also has this feature.
1. Press /> Messages.
2. Select Inbox (also includes SMS messages),
Drafts, or Sent Items.
ⅷ Priority — sets the message priority to normal or high.
ⅷ Valid Until — sets a date after which no more
attempts are made to deliver the message.
Ⅲ If you have more than 9 messages, scroll right or
left to display the next or previous page.
To send a message, you must address it to at least one
recipient. All other message fields are optional and you
can fill them in any order.
To open a message on the current page:
ᮣ
Highlight a message and press r.
50
Entering Text
Creating a Message
In message fields that require you to enter text, you can
begin entering the text from the keypad when the field
is highlighted.
1. Press /> Messages > [Create Message].
Tip: You can also select [Create Message] from Inbox, Drafts,
or Outbox or begin messages from Contacts, Recent
Calls, Media Center, or standby mode, or by replying to a
message in your inbox.
While entering text, press /to choose a text input
mode from the context-sensitive menu. (See “Entering
2. Address the message:
Ⅲ Select To. Enter the phone number or email
address from the keypad and press r. Repeat
this action to enter more phone numbers or email
addresses.
Message Size
You can create and send messages of up to 100 KB,
including attachments for MMS. The size of the
message appears at the top of the display as you are
creating the message.
– or –
Press Search (left softkey) to select recipients from
Contacts or Recent Calls. Highlight recipient(s),
press rto select them (entries will be checked),
and then press Done (left softkey).
Sending or Canceling
To send the message at any time after it has been
addressed:
Ⅲ If necessary, press Back (right softkey) to return
from the Send To screen to the main Message
screen.
ᮣ
Press Send (left softkey) or press /> Send.
To cancel the message at any time:
ᮣ
At the message screen, press Cancel (right softkey)
or press @to cancel the message and save it in
Drafts.
Tip: To remove a phone number or email address from the list
of message recipients, highlight the phone number or
email address and press Remove (left softkey).
51
3. To enter or edit the body of the message:
3. To attach a picture, audio, voice recording, or
video, select Attach > [New Attach] and then select
an option to attach a file.
Ⅲ Select Message and then use any of the following
options to enter your message.
4. To add CC’s, select Cc and add recipient(s).
Note: If you have created a signature, the signature
automatically appears in this field. Text you enter
5. To insert replies the recipient can choose from
when replying to your message, select Auto
Replies.
● Enter text from the keypad.
Ⅲ Enter text from the keypad or select a Quick Note
softkey) when you are finished.
6. To set the priority of the message, select Priority
and then select a setting.
● Insert a picture, a ring tone, or an audio file.
When you are finished, press r.
7. To set a date after which attempts to deliver the
message end:
4. To send the message without additional options,
press Send (left softkey) or press /> Send.
Ⅲ Select Valid Until, enter a date, and press r.
Ⅲ To set no date, press No Date (left softkey).
Adding More Message Options
8. To send the message, press Send (left softkey) or
press /> Send.
1. To view more fields in a message, scroll to MORE
and press r.
2. To create or edit the subject line, select Subject,
enter a subject, and press r.
52
Replying to a Message
Note: If the message you are replying to was sent with auto
replies, it contains a numbered list of possible replies.
Press the number of a reply. The reply is sent
immediately without any further action.
You can reply to a read message while you are viewing
it or while it is highlighted in the Message Center. You
cannot reply to unread messages.
More Ways to Begin a Message
When you reply to a message, some of the fields in
your reply are filled in automatically. These may include
To, Message (the first 40 characters of the received
message), Subject, and Cc.
In addition to beginning a message from the Message
Center, you can begin a message from Contacts, the
Recent Calls list, standby mode, or the Media Center.
To reply to a message:
To begin a message from Contacts:
1. Display or highlight a read message and press
Reply (left softkey). (To reply to the sender and all
recipients, press /> Reply All.)
1. From the Contacts list, highlight an entry.
2. Scroll left or right to view the Contacts types until
you see the icon for the phone number or email
address to which to send the message.
2. Select [Create Reply] and enter a reply message or
select a short reply from the list.
3. Press Create (left softkey) or press />
Create Message.
3. Edit any applicable message fields and press r.
4. Press Send (left softkey).
4. Create and send the message.
Tip: To create new reply phrases to use in later reply
messages, see “Quick Notes and Reply Phrases” on
To begin a message from the Recent Calls list:
1. From the Recent Calls list, highlight an entry.
53
2. If the entry has more than one phone number
stored, display the phone number to which to send
the message.
To insert a quick note:
1. While you are creating a message, highlight or
select Message or Subject and then press QNotes
(left softkey).
3. Press Create (left softkey) or press /> Create.
4. Create and send the message.
2. Select a Quick Note to insert into the message.
To begin a message from standby mode:
Tip: To add a quick note after you have already started
entering a message, press /> Insert >
Insert QNotes, and select a note.
ᮣ
Enter a phone number and press />
Create Message.
To create new Quick Notes to use in later messages, see
To begin a message from the Media Center:
1. From the Media Center, highlight or select a picture
or audio file.
Inserting Pictures or Videos
You can insert pictures or videos from Media Center. If
the forward locked icon (u) appears next to a file, it
cannot be included in a message.
2. Press Send (left softkey).
3. Create and send the message. The selected file is
automatically included as an attachment.
1. Highlight the Message field and press /> Insert >
Insert Picture or Insert Video (You will see a list of
available pictures or videos.) Scroll right or left to
display files in the phone’s memory or on the
memory card.
Quick Notes
When you are filling in the Message and Subject
message fields, you can add preset words or phrases
called Quick Notes. After you add Quick Notes, you
can edit them as you would any other text.
2. Highlight a picture or video and press r.
54
Removing an Inserted Item
Note: You can also select Capture Picture or Capture Video
to take a new picture or video to send.
To remove an item inserted into a message:
1. Select the Message field and highlight the item by
Inserting Audio Files or Voice Records
scrolling to the right.
You can insert audio files from the Media Center or
voice records from your voice records list. Preloaded
audio files or files with the forward locked icon (u)
cannot be included in a message.
2. Press Delete (left softkey).
Note: You can also attach items to messages by selecting
MORE and then selecting Attach.
1. Highlight the Message field and press /> Insert >
Insert Audio. (You will see a list of available audio
files.)
Drafts
While you are creating a message, you can save it in
Drafts before you send it. You can view, edit, send, or
delete saved drafts.
Tip: To hear an audio file before inserting it, highlight the file
name and press Preview (left softkey).
2. Highlight an audio file or voice record and
press r. (Scroll right or left to display available
files in the phone’s memory or on the memory
card.)
Saving a Message in Drafts
ᮣ
While you are creating a message, press />
Save in Drafts and the message will be saved in
drafts.
Ⅲ To record a voice record, select Record Voice and
After saving, you can continue to create the message.
The version you saved in Drafts will not change.
record a new voice record.
Accessing Saved Drafts
ᮣ
Press /> Messages > Drafts.
55
Sent Items
Receiving a Message
The Sent Items folder holds all messages that have
been sent.
When you receive an MMS message, a message
notification appears on the display.
To view the message:
Forwarding Sent Items
ᮣ
Press ror press Read (left softkey). The message
is downloaded from the message server.
1. Press /> Messages > Sent Items.
2. Highlight a message and press /> Forward.
3. Address, edit, and send your message.
To dismiss the message notification:
Press Later (right softkey).
ᮣ
Outbox
This icon 2 appears on the display, reminding you that
you have a new message.
Messages you tried to send are stored in the Outbox.
Threaded Inbox
Resending Messages
If a message was not sent from your phone, you can
resend it.
The threaded inbox allows you to organize your
messages by subject or sender.
1. Press /> Messages > Outbox.
1. From your inbox highlight a message.
2. Highlight a message and press Resend (left
softkey).
2. Press /> Threading and select None, Subject or
Sender.
Note: If your message was sent successfully, Resend will not
appear as an option.
56
Navigating a Message
Actions for Received Messages
As you scroll through a message, numbers, email
addresses, and Web addresses are highlighted.
Deleting
To delete unread messages:
Pictures and audio recordings are also highlighted.
1. Highlight a message and press Delete (left softkey).
2. Press ror press Yes (left softkey) to confirm.
To delete read messages:
Embedded Objects and Attachments
Messages may contain pictures or audio files as part of
the body of the message or as attachments.
1. Highlight or view a message and press />
If a message contains pictures or audio files in the
body of the message, highlight each picture or audio
file to view or play it.
Delete Message.
2. Press ror press Yes (left softkey) to confirm.
If a message contains a picture or audio file as an
attachment, highlight the attachment and press rto
view the picture or play the audio file.
Forwarding
1. Highlight or view a message and press />
Forward.
Note: Audio files in messages do not play if VibeAll is
2. Address, edit, and send your message.
set to On.
Embedded objects and attachments are included
when you forward a message.
57
To make a Talkgroup call to a Talkgroup ID in a message:
Locking and Unlocking
1. View the message.
When you lock a message, it cannot be deleted until
you unlock it.
2. Highlight a Talkgroup ID and then press />
Talkgroup.
ᮣ
Highlight or view a message and press />
Lock Message or Unlock Message.
3. Press the DC button.
Calling a Number in a Message
Storing Message Information to Contacts
If any field in a message contains a phone number,
Direct Connect number, or Talkgroup ID, you can call
or send a Call Alert to that number.
If a message you receive contains a phone number,
Direct Connect number, Talkgroup ID, or an email
address in any of the fields, you can store this
information to Contacts.
To make a call to a number in a message:
1. View the message.
1. View the message.
2. Highlight a number or email address and then
2. Highlight a number and press `to make a
phone call or press the DC button to make a Direct
Connect call.
press /> Save Number or Save Email.
3. Select [New Contact] to store the number in a new
entry, or select an entry to store the information to
an existing entry.
To send a Call Alert to a Direct Connect number in a
message:
4. With the Contacts type field highlighted, scroll left
or right to display a Contacts type for the number
or email address.
1. View the message.
2. Highlight a Direct Connect number and then press
press /> Alert.
5. Press Save (left softkey).
3. Press the DC button.
58
Going to a Website
Note: Most traditional phone-to-phone text messages arrive
as MMS messages on your MOTOROLA BRUTE. Your
phone can send and receive MMS messages.
If a message contains one or more Web addresses,
you can go to the website.
Your phone can receive SMS text messages, but it
cannot send them.
1. View the message.
2. Highlight a Web address and then press />
Go To Website.
Accessing Text Messages
Note: The entire Web address must appear in the message.
ᮣ
When you receive a text message, you will see an
alert. Press Read (left softkey) to display the
message.
Otherwise, you cannot go to the website.
Saving Attachments or Embedded Files
1. View a message.
Caller ID Blocking
2. Highlight an attachment or an embedded picture
or audio file and then press /> Save Picture,
Save Audio or Save Attachment.
Caller ID allows people to identify a caller before
answering the phone by displaying the number of the
incoming call. If you do not want your number
displayed when you make a call, follow these steps.
Text Messaging (SMS)
Per-Call Blocking
With text messaging (SMS), you can receive instant text
messages from another messaging-ready phone or
from an email account.
To block delivery of your number for a single phone call:
ᮣ
Press *67before dialing the call.
Your PTN is your ten-digit Personal Telephone Number.
59
Your Nextel phone number cannot be blocked from
calls made to 911, 800, 855, 866, 877, 888, or other
toll-free phone numbers.
To accept the second call and end the active call:
1. Press @. Your phone rings with the second call.
2. Answer the second call.
Per-Line Blocking
To decline the second call:
You can request that Nextel Customer Service
permanently block delivery of your phone number on
every call you make. In this case, you may need to
display your number for certain calls.
ᮣ
Press No (right softkey). If you subscribe to
voicemail, the call is forwarded to your voicemail
box, unless you set Call Forward or If Busy to a
different number.
To show your number on a per-call basis:
Turn Off Call Waiting
ᮣ
Press *82before dialing the call.
To turn off Call Waiting before a call:
ᮣ
Press *70before dialing the call. Call Waiting
is reactivated once the call ends.
Call Waiting
To turn off Call Waiting during a call:
Press /> In Call Setup > Call Waiting > Off.
Call Waiting lets you receive a second call while on an
active call. Call Waiting is always available, unless you
turn it off for a specific call.
ᮣ
Tip: To turn Call Waiting back on while still on the call, set this
If you are on a call and receive a second call, your
phone emits a tone and displays a message.
option to On.
To accept the second call and put the active call on hold:
ᮣ
Press Yes (left softkey).
60
1. During an active phone call, press /> 3 Way.
(The first call is placed on hold.)
Making a Second Call
2. Enter a second phone number and press `.
1. Place or receive a phone call.
3. Press Join (right softkey).
2. While the call is active, press /> 2nd Call. (The
first call is placed on hold.)
If one of the people you called hangs up during the
call, you and the remaining caller stay connected. If you
initiated the call and are the first to hang up, all callers
are disconnected.
3. Enter a second phone number and press `to
place the call.
Note: For quick ways to enter the number, press /.
To merge two calls into a three-way call:
To end the second call and make the on-hold call active:
1. During an active phone call, press /> 2nd Call.
(The first call is placed on hold.)
ᮣ
Press @.
To make the on-hold call active and put the active call on
hold:
2. Enter a second phone number and press `.
3. Press /> Join.
ᮣ
Press Switch (right softkey).
Call Forwarding
Making a Three-Way Call
Call Forwarding lets you forward all your incoming calls
to another phone number – even when your phone is
turned off. You can continue to make calls from your
phone when Call Forwarding is activated.
With Three-Way Calling, you can talk to two people at
the same time. When using this feature, the normal
airtime rates will be charged for each of the two calls.
61
Call Forwarding sends calls to the phone numbers you
specify. You can forward all calls to one number or
forward missed calls to different numbers depending
on the reason you missed the call.
To forward all calls:
1. Press /> Settings > Phone Calls > Call Forward >
Forward > All Calls.
2. Select To.
Forwarding All Calls
Ⅲ If you specified a forwarding number for all calls
When you set your phone to forward all calls, an icon
appears in the top row of the display:
before, this number appears.
Ⅲ To forward calls to this number, highlight it and
press r.
Phone line 1 is active; calls to phone line 1 are
being forwarded.
&
Ⅲ To delete this number, press rand then press
and hold Delete (left softkey).
Phone line 1 is active; calls to phone line 2 are
being forwarded.
)
3. To enter a forwarding number:
Ⅲ Enter the number or press Search (left softkey),
select Contacts, Recent Calls or Memo and then
select a number.
Phone line 1 is active; calls to phone lines 1 and 2
are being forwarded.
;
Phone line 2 is active; calls to phone line 1 are
being forwarded.
(
4. Press r. All your calls are now forwarded to the
number you specified.
Phone line 2 is active; calls to phone line 2 are
being forwarded.
*
Turning Off Call Forwarding
Phone line 2 is active; calls to phone lines 1 and 2
are being forwarded.
<
1. Press /> Settings > Phone Calls > Call Forward >
To.
2. Set this option to Off.
62
All your calls are now sent to your phone.
2. Select If Busy to specify a forwarding number for
calls received when your phone is busy.
Forwarding Missed Calls
3. If you specified a forwarding number for this type
of call before, this number displays.
Calls you miss are forwarded according to the options
set for missed calls. By default, missed calls are
forwarded to voicemail.
Ⅲ To forward calls to this number, highlight it, press
You can specify a forwarding number for each type of
missed call:
Ⅲ To delete this number, press r, and then press
and hold Delete (left softkey).
ⅷ If Busy — Your phone is on a call or transferring data.
4. To enter a forwarding number:
ⅷ If No Answer — You do not answer on the first four
rings.
Ⅲ Enter the number or press Search (left softkey),
select Contacts, Recent Calls or Memo and then
select a number.
ⅷ If Unreachable — Your phone is out of coverage or
powered off.
5. Press r.
Note: You are charged a higher rate for calls you have
6. Repeat step 2 through step 5 for If No Answer and
If Unreachable.
forwarded.
To forward missed calls:
7. When you are finished, press Back (right softkey).
1. Press /> Settings > Phone Calls > Call Forward >
Forward > Detailed.
Note: If your phone is set to forward all calls, you must first
turn off call forwarding to access this option. (See
63
number. Relay service works through a
Making International Calls
Communications Assistant who reads messages typed
into a TDD/TTY device by a speech or hearing
impaired individual to you. The Communications
Assistant then types your spoken messages to the
hearing or speech impaired individual.
Your service default is “International Calls Restricted.”
Contact Nextel Customer Service to obtain
international dialing access.
Calls placed between the United States and Canada
do not require an international access code.
Telecommunications Relay Service is available 24
hours a day, seven days a week, and every call is
strictly confidential.
Special Dialing Codes
Note: Using 711 to reach Telecommunications Relay Service
may not be available in all areas.
Non-Emergency Numbers
The TTY device must be connected to the phone
through the micro USB port. A 2.5 mm to micro USB
adapter is required to support TTY.
Nextel supports many “non-emergency” numbers
(such as #77, 311, and 511) provided by local and state
governments. These numbers are used to report
non-emergency incidents. If the situation includes
imminent danger or loss of life, you should dial 911.
To enable TTY mode:
1. Press /> Settings > Phone Calls > TTY > Use TTY.
2. Select On to enable TTY mode.
Telecommunications Relay Service
3. For TTY options, highlight Type, press rand then
select an option:
Nextel supports services for communicating with
speech and/or hearing impaired individuals. You can
dial 711 to reach a local Telecommunications Relay
Center. You will then be connected to your destination
Ⅲ TTY – Type and read text on your TTY device.
Ⅲ VCO (Voice Carry-Over) – Speak into the phone
and read text replies on your TTY.
64
Ⅲ HCO (Hearing Carry-Over) – Type text on your
TTY and listen to voice replies on your phone.
ⅷ Choose a Second Line Service plan that fits your
needs.
In order to activate Second Line Service, contact your
Nextel Sales Representative or call Nextel Customer
Service.
Nextel Phone Services
Contact Nextel Customer Service to obtain these
services or for additional information.
To set the active line (primary or alternate):
1. Press /> Settings > Phone Calls > Set Line.
2. Select a phone line to be active.
Note: Some services are not available outside of the
continental United States.
When incoming calls are made to a non-active line,
they will be sent to voicemail without ringing. (See “Call
Second Line Service
You can have two different phone numbers on the
same phone. With Second Line Service, you can:
Sprint 411
ⅷ Get separate bills for each phone line.
Dial 411 from your wireless phone to receive
ⅷ Bring in an existing wireless or home phone number
to Nextel to activate on the second line.
nationwide listings, movie listings and showtimes,
restaurant reservations, and driving directions, as well
as sports scores, stock quotes, and weather conditions.
Spanish speaking operators available. Receive up to
three phone numbers or pieces of information per call,
and be automatically connected at no additional
charge. Airtime and other charges apply.
ⅷ Have two different area codes (must be in same
market) to convey a local image to callers.
ⅷ Use different ringer styles so that you can tell which
line is receiving a call.
ⅷ Forward incoming calls to either your primary or
alternate line phone number.
65
Options available under the home page include:
ⅷ Business Tools – Provides access to business tools.
ⅷ Text Messaging – Provides access to text messaging.
5. Data Services
ⅷ Games, Ringers, & More – Provides access to
downloadable items.
ࡗ ࡗ ⅷ News, Sports & More – Lets you access news
services.
ⅷ NASCAR –Gives you access to NASCAR news and
stats and provide a link to download NASCAR Sprint
Cup Mobile.
Wireless Data Services
ⅷ Email & IM – Allows you to send email and IMs.
With Web access on your phone, you can browse your
favorite websites, making it easier than ever to stay
informed while on the go. Follow sports scores,
breaking news, and weather, and shop on your phone
anywhere on the Nextel National Network.
ⅷ Your Bookmarks – Allows you to access and manage
your bookmarks.
ⅷ Search – Launches a Web search.
ⅷ Go to URL – Lets you enter website addresses.
Using the Web Browser
ⅷ My Account – Lets you configure and manage your
browser settings.
Navigating the Web from your phone is easy once you
get the hang of it.
ⅷ Help – Displays online help.
Tip: To go back one page, press the *key .
Opening the Browser
To access the browser menu options, press and hold /
from any Web page.
ᮣ
Press /> Web > Net.
66
Going to a Specific Website
Note: Bookmarking a page does not store the page contents,
just its address.
To go to a particular website by entering a Web address
(URL):
Some pages cannot be bookmarked. Whether a
particular Web page may be marked is controlled by its
creator.
1. From the home page, select Go to URL.
2. Press Edit (left softkey).
Accessing a Bookmark
From the home page:
3. Use your keypad to enter the Web address and
press Done (left softkey).
4. Press Options (right softkey) > accept to go to the
1. Select Your Bookmarks.
website.
2. Highlight a bookmark and press r(or press the
number corresponding to the bookmark).
Note: Not all websites are viewable on your phone.
From any other Web page:
Creating a Bookmark
1. Press and hold /to open the browser menu.
2. Select View Bookmarks.
Bookmarks allow you to store the address of your
favorite websites for easy access at a later time.
1. Go to a Web page and press and hold /to open
the browser menu.
3. Select a bookmark and press r(or press the
number corresponding to the bookmark).
2. Highlight Mark this page and press r.
Tip: To return to the home page from any other Web page,
press @.
3. Confirm or edit the bookmark name, scroll to the
bottom of the screen, and then press Done (left
softkeys) to save the bookmark.
67
Reloading a Web Page
Downloading Content
1. Press and hold /to open the browser menu.
Your phone arrives with Java applications and games
loaded and ready to install. You can download and
install more Java applications. For more information on
Java Security, see “Setting Privacy for Each Java
2. Select Refresh this page. (The browser will reload
the current Web page.)
Restarting the Web Browser
If the Web browser seems to be malfunctioning or
stops responding, you can usually fix the problem by
simply restarting the browser.
Check the Games, Ringers & More menu option for a
catalog of items available for purchase and download.
account for a wide selection of available Java
applications and downloading instructions.
1. Press and hold /to open the browser menu.
2. Select More... > Restart Browser.
Note: Using Java applications may cause your phone’s
battery power to deplete more quickly.
68
Sound Settings
6. Settings
Ring Tones
Your phone provides a variety of ringer options that
allow you to customize your ring and volume settings.
These options allow you to identify incoming calls and
messages by the ring.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ Selecting Ringer Types
1. Press /> Multimedia > Ring Tones.
2. Scroll through the list of ring tones. A sample
ringer will sound as you highlight each option.
3. Press ror press Assign (left softkey).
4. Select the function(s) to which to assign the current
ringer by highlighting the option and pressing r.
(A check mark appears next to selected options.)
5. When you are finished, press Done (left softkey) to
assign the ringer to the selected function(s).
69
Assigning a Ring Tone to a Contact
Downloading More Ring Tones
You can also assign a ringer to a specific contact entry
so you know who's calling without looking at the
phone.
To use other ring tones, you can download them into
your phone for a fee.
ᮣ
Press /> Multimedia > Ring Tones > Buy Ring
1. Press /> Multimedia > Ring Tones.
Tones.
2. Scroll through the list of ring tones and select one.
A sample ringer will sound as you highlight each
option
Note: Ring tones may be downloaded only once. If you
delete a ring tone from your phone and wish to
reassign it, you must purchase it again.
3. Press ror press Assign (left softkey).
Managing Memory
4. Select A Contact....
To view the amount of memory available for custom ring
tones:
5. Highlight a Contacts entry and press rto assign
the ringer.
1. Press /> Multimedia > Ring Tones.
Viewing Ring Tone Assignments
1. Press /> Multimedia > Ring Tones.
2. Make sure Vibrate All is set to Off.
2. Make sure Vibrate All is set to Off.
3. Highlight any ring tone and press />
Memory Usage.
Deleting custom ring tones frees memory.
3. Highlight any ring tone and then press />
Overview.
Deleting Ring Tones
4. Scroll to view ring tones assigned to features and
Contact entries.
Deleting a ring tone from the list deletes it from your
phone.
70
In most cases, when you delete a ring tone that you
purchased from your phone, you will have to purchase
it again.
Press /> Multimedia > Ring Tones > Vibrate All.
Set this option to On or Locked.
Tip: Setting this option to Locked requires you to press and
hold the volume control up to turn Vibrate All off. The
Locked option helps prevent you from accidentally
turning Vibrate All off.
To delete a ring tone:
1. Press /> Multimedia > Ring Tones.
2. Make sure Vibrate All is set to Off.
3. Highlight a ringtone and press /> Delete.
4. Press Yes (left softkey) to confirm.
To deactivate Vibrate All:
1. Press and hold the volume key up to unlock
vibrate all.
2. Press the volume key up repeatedly to select a
volume level or press /> Multimedia >
Ring Tones > Vibrate All > Off.
Vibrate Settings
Vibrate All
These icons indicate how the ringer is set:
The Vibrate All option allows you to be notified of calls
and messages with a vibration instead of an audible
alert.
The phone always vibrates instead of
making a sound.
/
To activate Vibrate All:
The phone vibrates instead of making a
sound for phone calls.
.
ᮣ
Press and hold the volume button down in standby
mode. (Pressing and holding displays “VibeAll:
On.” Continuing to hold the button down displays
“VibeAll: Locked.”)
Direct Connect calls, Group Connect calls,
and Talkgroup calls are heard through the
earpiece, not the speaker.
"
– or –
71
Silence All
The phone vibrates then rings for all calls.
The ring volume is set to zero for all calls.
/
The Silence All option allows you to mute all sounds
without turning your phone off.
,
Ring and Vibrate
To activate Silence All:
To set your phone to ring and vibrate when you receive
phone calls or Call Alerts:
ᮣ
With the phone in standby mode press and hold
the volume key down until the ringer level is set
at 0. (The screen will display ,.)
1. Press /> Multimedia > Ring Tones.
2. Make sure Vibrate All is set to Off.
3. Scroll through the list and select a ring tone.
4. Press /> Assign w/Vibe.
To deactivate Silence All:
ᮣ
Press the volume key up repeatedly to select a
volume level.
To set your phone to vibrate instead of making a sound for
some features but not others:
5. Select Phone Line 1 and/or Phone Line 2 and press
Done (left softkey).
1. Press /> Multimedia > Ring Tones.
2. Make sure Vibrate All is set to Off.
3. Select Vibrate from the list of ring tones.
This icon/appears on the display.
Note: You can also set 3D sound effects settings in the Ring
Tones menu (/> Multimedia > Ring Tones > 3D
Effect) or when assigning a ring tone.
4. Select the feature(s) to which to assign Vibrate and
press Done (left softkey).
Note: To set ring options for Direct Connect calls, Group
Connect calls, and Talkgroup calls, see “Vibrate
72
Adjusting the Phone’s Volume Settings
Display Settings
Adjust your phone’s volume settings to suit your needs
and your environment.
Changing the Backlight Time Length
1. Press /> Settings > Volume.
Select how long the display screen and keypad remain
backlit after any keypress is made.
2. Select Ringer/Alerts, Speaker, Earpiece, Multimedia
or Keypad.
1. Press /> Settings > Display/Info > Backlight.
3. Choose a volume level and press r.
2. Highlight an option, press r, and then choose a
setting.
Tip: You can adjust the ringer volume in standby mode (or
the earpiece volume during a call) by using the volume
key on the left side of your phone.
Ⅲ For Timer or Java Timer, select a time.
Note: Long backlight settings reduce the battery’s talk and
standby times.
Beep
Set your phone to alert you with an audible tone once
a minute during a voice call.
Changing the Display Screen
Choose what you see on the internal or external
display screen while powering on or off and when in
standby mode.
1. Press /> Settings > Phone Calls > Minute Beep.
2. Highlight On or Off and press r.
1. Press /> Settings > Display/Info > Wallpaper >
Internal or External.
73
2. Select an image and press View (left softkey) to view
it. Press Back (right softkey) to return to the
available images.
Ⅲ List View to display the menu as a list.
Ⅲ Tab View to display the menu as a row of icons on
the bottom of the screen.
3. Press rto assign an image.
Changing the Theme
Setting Wallpaper to Change Automatically
Customize your phone’s display appearance by
selecting a theme to reflect your personality.
When you set your wallpaper to change automatically,
your phone uses each of the pictures in Media Center
as wallpaper, cycling through them at a pace you
choose.
1. Press /> Settings > Display/Info > Theme.
2. Highlight an option and press r.
1. Press /> Settings > Display/Info > Wallpaper >
Internal or External > Auto Cycle.
Changing the Clock Display
Select a format for the time and date display and
choose whether the time and date appear in standby
mode.
2. Select how frequently the wallpaper will change
then press r.
Changing the Phone’s Menu Style
1. Press /> Settings > Display/Info > Clock.
Choose how your phone’s menu is displayed on the
screen.
2. Select Display On/Off, Time Format or Date Format
and then press r.
1. Press /> Settings > Display/Info > Menu View.
3. Select an option and press rto apply the setting.
2. Highlight an option and press r.
Note: The year is set by the network, and even though it is an
option, it cannot be changed.
Ⅲ Icon View to view the main menu as a grid of
icons. Icons animate when they are highlighted.
74
also choose to be notified with a sound while making a
phone call.
Changing the Text Size
Adjust the font when entering text (for example, when
using the notepad or when adding a Contacts entry).
1. Press /> Settings > Phone Calls > Notifications.
2. Highlight Receive All, Message Mail Only or Delay All
1. Press /> Settings > Display/Info > Text Size.
and press r.
2. Highlight an option and press r.
Note: Delay All is the default setting.
Messaging Settings
Tip: To set notification options during a call press />
In Call Setup > Notifications.
Staying connected to your friends and family has never
been easier. With your phone’s advanced messaging
capabilities, you can send and receive many different
kinds of text messages without placing a voice call.
(For more information see “Multimedia Messages
Customizing MMS
The Setup menu lets you customize MMS for your
phone:
ⅷ Signature — Enter text here to create a signature that
is automatically inserted at the end of each message.
Messaging settings make messaging easier by letting
you decide how you would like to be notified of new
messages, create a signature with each sent message,
and create your own preset messages.
ⅷ Quick Notes — lets you create new Quick Notes and
edit or delete Quick Notes you have created.
ⅷ Cleanup — controls how long messages remain in
the Inbox and Sent Items before they are deleted.
Setting Message Notification
ⅷ Report Default— allows you to set the default for the
Delivery Report Option to on or off.
When you receive a message, your phone notifies you
by displaying an icon on your display screen. You can
ⅷ Memory Size — displays a report on phone memory.
75
ⅷ MMS Setup — allows you to set up the following:
2. Select [New Quicknote] or [New Reply], or press
New (left softkey).
Ⅲ Friendly Name — lets you enter the name
displayed in the From field on messages you
send.
3. Enter text and press r.
To edit a Quick Note or reply phrase:
Ⅲ Download Options — lets you control message
downloads. Automatic downloads messages
automatically. Manual requires you to reply to a
prompt before messages download to your
phone.
1. From the Setup menu, select Quick Notes or
MMS Setup > Replies.
2. Select a Quick Note or reply phrase you have
created.
Ⅲ Replies — lets you create new reply phrases and
edit or delete reply phrases you have created.
3. Edit the text and press r.
To delete a Quick Note or reply phrase:
To access the Setup menu:
1. From the Setup menu, select Quick Notes or
MMS Setup > Replies.
1. Press /> Messages.
2. Highlight [Create Message] and press /> Setup.
2. Highlight a Quick Note or reply phrase you have
created.
Tip: This option is available from many context-sensitive
menus when you are using MMS.
3. Press Delete (left softkey) and then press ror
press Yes (left softkey) to confirm.
Quick Notes and Reply Phrases
Note: You can edit or delete all Quick Notes. You can only
To add a Quick Note or Reply phrase:
edit or delete Reply phrases that you created.
1. From the Setup menu, select Quick Notes or
MMS Setup > Replies.
76
Setting the Cleanup Option
The cleanup option controls how long messages
remain in the Inbox and Sent Items before they are
deleted. You set the cleanup option for the Inbox and
Sent Items separately.
Airplane Mode
Sometimes you may want to have your phone on, but
turn off its ability to make and receive calls and other
transmissions.
The cleanup option deletes only read, unlocked
messages.
To set the cleanup options:
To set your phone so that it cannot make or receive phone
calls, Direct Connect calls, Group Connect calls, Talkgroup
calls, or transfer data:
1. From the Message Center, press /> Setup >
Cleanup > Inbox or Sent Items.
2. Choose a cleanup option.
1. Press /> Settings > Advanced > Transmitters.
2. Select Off and press r.
3. To automatically delete messages now, press r
or press Yes (left softkey). To delete messages later,
press No (right softkey).
3. Press Yes (left softkey).
When in Transmitters Off mode, your phone’s standby
screen displays “Transmitters Off.”
Adding a Customized Signature
Add a customized signature to each message you
send.
Note: While powering on your phone, you can turn
transmitters off by pressing .for more than five
seconds.
1. Press /> Messages > /> Setup > Signature. If
you do not wish to attach a signature to your
outgoing messages, press Delete (left softkey).
77
To restore your phone’s ability to do all these things:
Headset Options
ᮣ
Set this option to On and then press Yes (left
softkey).
To set your phone to send incoming sound to a headset
only, or to a headset and a speaker at the same time:
Note: When Transmitters is set to Off, your phone’s Bluetooth
capability is disabled, and all active Bluetooth
connections are dropped.
1. Press /> Settings > Advanced > Headset/Spkr.
2. Select HdsetOnly to send incoming sound to the
headset only.
Setting One Touch Direct Connect
– or –
Select Hdset&Spkr to send incoming sound to the
headset and ring tones to the speaker.
One Touch Direct Connect sets your phone to call the
most recent Direct Connect number or Group on the
Recent Calls list, or a Direct Connect number you
choose, every time you press the DC button.
Profiles
1. Press /> Push To Talk > PTT Options >
One Touch DC.
A profile is a group of settings saved together so that
you can apply them to your phone easily.
2. Select from Off, Quick PTT, Last Call, Assigned
Number, Send Picture, Send My Info or Send Contact
and press r.
Your phone arrives with preset profiles. You can also
create your own profiles.
Tip: If you are entering a Talkgroup number, enter # before
Viewing Profiles
the number.
To view the profiles stored in your phone:
1. Press /> Tools > Profiles.
78
2. Highlight a profile and press View (left softkey).
ⅷ Creates a temporary profile that contains these
changes.
Tip: The profile that is currently in effect on your phone has a
checkmark next to it.
To set your phone to create a temporary profile that
contains changes you make to settings:
3. Scroll to view settings.
1. Press /> Tools > Profiles.
Switching Profiles
2. Press /and then select Setup > Temp Profile.
3. Set this option to On.
1. Press /> Tools > Profiles.
2. Highlight a profile and press r.
The profile you selected is now in effect.
To set your phone to update the profile in effect to reflect
any changes you make to settings:
ᮣ
Set Temp Profile to Off in step 3 above.
How Changing Settings Affects Profiles
Temporary Profiles
Many of the settings contained in profiles can be set
without switching or editing profiles — for example, by
selecting Settings or Ring Tones to set options, or by
setting the volume of the phone’s ring using the
volume controls.
If your phone is set to create temporary profiles, a
temporary profile is created when you make changes
to settings without switching or editing profiles. These
stay in effect until you switch profiles or power off your
phone.
When you do this, your phone either:
ⅷ Updates the profile in effect to reflect these changes,
without notifying you.
Temporary profiles and any settings you have changed
are marked with asterisks (*).
– or –
79
If you do not choose a profile to copy from, the new
profile is based on a default profile.
Storing a Temporary Profile
To store a temporary profile as a new profile:
1. Press /> Tools > Profiles.
4. Press Create (left softkey).
5. Scroll through the list of options and set their
values.
2. Highlight the temporary profile and press />
Store As New.
6. When you are finished, press Done (right softkey).
3. Enter a name and press r.
Editing Profiles
To overwrite the profile the temporary profile is based on:
1. Press /> Tools > Profiles.
1. Press /> Tools > Profiles.
2. Highlight the temporary profile, press
/> Store Changes, and then press Yes
(left softkey).
2. Highlight a profile, press /and then select Edit.
3. Scroll through the list of options and set their
values.
Note: The temporary profile is stored with the name of the
profile it is based on. The profile it is based on, as it
existed before you made changes to settings, is gone.
4. When you are finished, press Done (right softkey).
Deleting Profiles
Creating Profiles
To delete a profile:
1. Press /> Tools > Profiles.
1. Press /> Tools > Profiles > [New Profile].
2. Highlight a profile, press /, and then select
2. Enter a name and press r.
Delete.
3. To base this profile on an existing profile, select
Copy From and then select a profile and press r.
3. Press ror press Yes (left softkey).
80
To delete all profiles:
Ⅲ DC/GC – sets filtering options for Direct Connect
calls and Talkgroup calls.
1. Press /> Tools > Profiles.
●
Off – notifies you of all DC and Talkgroup calls.
2. Press /and then select Delete All.
3. Press ror press Yes (left softkey) to confirm.
●
On – ignores all DC and Talkgroup calls.
Ⅲ Group – sets filtering options for Group Connect
calls.
Setting Call Filtering
●
Off – notifies you of all Group Connect calls.
The call filtering setting in each profile lets you control
which calls, Call Alerts, and message notifications your
phone notifies you of, and which it ignores.
●
On – ignores all Group Connect calls.
Ⅲ Alerts – sets filtering options for Call Alerts.
●
Off – notifies you of all Call Alerts.
1. While setting options for a profile, select Call Filter.
●
On – ignores all Call Alerts.
2. Select a filtering option
Ⅲ Notifications – sets filtering options for message
notifications.
Ⅲ Phone – sets filtering options for phone calls.
●
●
●
Off – notifies you of all calls.
●
●
●
●
Off – notifies you of all messages.
Voice Messages – ignores all voice messages.
Text Messages – ignores text messages.
All – ignores all messages.
All – ignores all calls.
All Contacts – notifies you only of calls from
Contacts.
●
Some Contacts – notifies you only of calls from
selected Contacts. Select up to five Contacts
entries. When you are finished, press Done
(right softkey).
Note: The message notification screen still appears when you
receive a message you have set not to sound a tone or
vibrate.
3. Press Done (right softkey).
81
5. To record a voice name for the shortcut, select
Voice (optional). Follow the prompts to say and
repeat the name. Speak clearly into the
microphone.
Phone Setup Options
Shortcuts
6. Press Done (left softkey).
Your phone offers you the option of assigning shortcuts
to favorite or often-used functions. Pressing the /key
in standby mode followed by the assigned shortcut key
will launch your personally designated shortcuts.
7. If the number key you select is already assigned to
a shortcut, a prompt appears asking to replace the
existing shortcut.
Ⅲ Press Yes (left softkey) to replace the existing
shortcut.
Creating a Shortcut
Note: When you receive your phone, all number keys may
already be assigned to shortcuts. If this is the case, you
can create new shortcuts by deleting or replacing
existing shortcuts.
Ⅲ Press No (right softkey) to keep the existing
shortcut and assign another number key.
Using a Shortcut
1. Go to a menu item.
To access a shortcut using the shortcut number:
1. From standby mode, press /.
For example, to create a shortcut to the screen for
creating a new Contacts entry: Press />
Contacts and then highlight [New Contact].
2. On your keypad, press the number assigned to the
shortcut.
2. Press and hold /until a confirmation screen
appears.
To access a shortcut using the voice name:
3. Press ror press Yes (left softkey).
1. Press and hold s (the speaker button on top of
the phone).
4. Press a number key for the shortcut and press r.
82
2. Say the voice name you assigned to the shortcut.
The shortcut with that voice name is then
highlighted.
To change the number or voice name assigned to a
shortcut:
1. Press /> Settings > Personalize > Shortcuts.
To view a list of your shortcuts:
2. Highlight any shortcut and press Edit (left softkey).
ᮣ
Press /> Settings > Personalize > Shortcuts.
3. With Key or Voice highlighted, press rto change
assignments.
Editing a Shortcut
4. Press Done (left softkey).
To change the order of shortcuts:
Deleting Shortcuts
1. Press /> Settings > Personalize > Shortcuts.
2. With any shortcut highlighted, press /> Reorder.
To delete a shortcut:
3. Highlight the shortcut you are moving and press
1. Press /> Settings > Personalize > Shortcuts.
2. Highlight a shortcut and press /> Delete.
3. Press ror press Yes (left softkey) to confirm.
To delete all shortcuts:
Grab (left softkey).
4. Scroll to a new location and press Insert (left
softkey).
5. Repeat step 2 through step 4 for all the items you
are moving.
1. Press /> Settings > Personalize > Shortcuts.
6. Press Done (right softkey).
2. With any shortcut highlighted, press /> Delete
All.
3. Press ror press Yes (left softkey) to confirm.
83
Carousel
Personalize
Carousel is an iconic list of application shortcuts
displayed horizontally at the bottom of the display in
standby mode that allows you to access a total of nine
applications.
In addition to Shortcuts, the Personalize menu gives
you other options to access menu items easily.
ᮣ
Press /> Settings > Personalize, select an option,
and set your preferences.
To scroll through the list of icons, press the navigation
key right or left to highlight an icon, and press rto
select the icon.
Ⅲ Reorder Menu to change the main menu order.
Ⅲ Up Key, Down Key, Left Softkey, Right Softkey, to
set one-touch menu access from the standby
screen.
Configuring Auto Hide Settings
ᮣ
Press /> Settings > Personalize > Carousel >
Auto Hide.
Ⅲ Power Up to set the menu item displayed when
you power on your phone. (Default Ready starts in
standby mode.)
Ⅲ Select from Always On, 2 sec, 4 sec, or 8 sec.
Note: Carousel will not time out if Always On is selected.
Call Answer Mode
Assigning Carousel Applications
Select how to answer incoming calls on your phone.
1. Press /> Settings > Phone Calls.
1. Press /> Settings > Personalize > Carousel.
2. Assign applications to Left 1, Left 2, Left 3, Left 4,
2. Select an option and press r.
Center, Right 1, Right 2, Right 3, and Right 4.
Ⅲ Any Key Ans: Select On to allow you to answer an
incoming call by pressing any key.
3. Press rto assign the applications.
– or –
84
Select Off to require you to press `to answer all
incoming calls.
Setting Prepend Dialing
The Prepend feature lets you set a prefix to be added to
the beginning of all dialed numbers, such as a country
code for international calls.
Ⅲ Auto Ans to set your phone to automatically
answer an incoming call after a specified number
of rings when connected to a headset or
hands-free car kit.
1. Press /> Settings > Phone Calls > Prepend.
●
Off to disable Auto-Answer.
2. Select Prepend > On.
●
1 Ring, 2 Rings, 3 Rings or 4 Rings to answer
calls automatically when the phone is
connected to a hands-free car kit or a headset
(sold separately). In Auto-Answer mode, your
phone will answer calls even if you are not
present.
3. Enter a prefix in the Number field (such as +1 for
international calls) and then press r.
Ⅲ To deactivate this feature, select Off during step 2
above.
Note: This setting does not apply to 911 or Sprint 411.
Ⅲ Flip Activation to set your phone to answer calls by
opening the phone (Flip To Ans) and end calls by
closing the phone (Flip To End).
Resetting Your Phone
Resetting Phone Settings
Display Language
Resetting phone settings restores all the factory
defaults, including the ringer types and display settings.
The Recent Calls, Scheduler, and all text messages will
be erased. Contacts are not affected.
You can choose to display your phone’s onscreen
menus in several languages.
1. Press /> Settings > Display/Info > Language.
2. Highlight English, Español, Français or Automatic
and press r.
85
1. Press /> Settings > Advanced > Reset Defaults >
Reset Settings.
GPS Privacy Options
Your phone’s GPS privacy options control whether Java
applications or other software applications on your
phone may view the location of your phone. You may
set your phone to one of these GPS privacy options.
2. Enter your phone’s six-digit security code and
press Ok (left softkey). (A disclaimer is displayed.)
Note: Your security code is a six-digit number used for
resetting your phone. Please contact Nextel Customer
Service if you do not know your security code.
Note: Privacy options do not apply to the transmission of
location information during emergency 911 calls.
3. Read the prompt and press Yes (left softkey) to
complete the reset. (Press No [right softkey] to
cancel.)
To set your GPS privacy options:
1. Press /> Tools > GPS > Privacy.
2. If your GPS PIN security feature is enabled, enter
your GPS PIN. (See “Setting the GPS PIN Security
Feature” on page 87. for more information.)
Resetting All
Selecting Reset All resets phone settings and clears all
phone data, including Contacts, History, Scheduler, and
Messaging.
3. Select a privacy option:
Ⅲ Restricted — No Java or similar software
applications may view the location of your phone.
However, location information may still be
available to the phone’s owner, fleet manager, or
account administrator.
1. Press /> Settings > Advanced > Reset Defaults >
Reset All.
2. Enter your security code and press Ok (left
softkey).
3. Read the prompt and press Yes (left softkey) to
complete the reset. (Press No [right softkey] to
cancel.)
Ⅲ Unrestricted — All applications may view the
location of your phone, without notifying you.
86
Ⅲ By Permission — When an application attempts to
view the location of your phone, you will be
prompted to give permission. However, location
information may still be available to the phone’s
owner, fleet manager, or account administrator.
To change your GPS PIN:
1. Press /> Settings > Security >
Change Passwords > GPS PIN.
2. Enter the current GPS PIN and press Ok (left
softkey).
Setting the GPS PIN Security Feature
3. Enter the new GPS PIN and press Ok (left softkey).
To prevent your GPS privacy settings from being
altered without your knowledge, your GPS privacy
option can be protected by a PIN.
4. Reenter the new GPS PIN to confirm and then
press Ok (left softkey).
When you receive your phone, the GPS security feature
is turned off, so you do not have to enter a GPS PIN to
access your GPS privacy options. If you turn this
feature on, you will be required to enter a GPS PIN to
access your GPS privacy options.
Java Applications & GPS Security
Some Java applications can make use of your phone’s
GPS feature to determine the approximate
geographical location of your phone. (See “GPS
feature.) However, for privacy reasons, you may not
always want Java applications to access the location of
your phone. Your phone protects your privacy by giving
you the option to block all or some Java applications
from accessing the location of your phone.
To turn the GPS Enabled security feature on or off:
1. Press /> Settings > Security > GPS PIN.
2. Select On or Off.
3. Enter the current GPS PIN.
Tip: The default GPS PIN is 0000.
Setting Privacy for All Java Applications
4. Press Ok (left softkey).
See “GPS Privacy Options” on page 86 for instructions
on setting the privacy options for your java applications.
87
These options control the privacy of all Java
applications on your phone.
3. Press /> Permissions.
4. Select privacy options for this application (you may
set them for each of the menus available under
Permissions):
Granting or Denying Permission
When a java application requests access to the
location of your phone, a screen appears informing
you.
Ⅲ Always — The application always has permission
to access the phone’s location without notification.
Ⅲ Ask — When the application requests access to
the phone’s location, you are prompted to grant
or deny permission (see “Granting or Denying
Permission” on page 88).
To grant or deny a request:
1. Press Grant (left softkey) or Deny (right softkey) to
grant or deny a request.
Ⅲ Never — Requests for location are denied without
notification.
2. Select Always to always take this action for the
application, For this session to keep this action
without notification until the phone is powered off,
or Only Once to take this action for this instance
only (you will be prompted again for subsequent
requests).
DC/GC Options Menu
The PTT Options menu controls how your phone
handles Direct Connect calls, Group Connect calls, and
Talkgroup calls.
Setting Privacy for Each Java Application
1. Press /> Games and Apps.
To access the DC/GC Options menu:
2. Highlight an application or suite of applications.
ᮣ
Press /> Push To Talk > PTT Options.
Tip: If the application has requested access to the location of
your phone, this icon fappears when you highlight the
application.
Ⅲ Tkgrp Silent — controls whether you hear your
Talkgroup calls.
88
Ⅲ Tkgrp Area — lets you define your Talkgroup area.
Security Settings
Ⅲ One Touch DC — sets One Touch Direct Connect.
Ⅲ Alert Type — controls how your phone notifies you
when you receive Direct Connect calls, Group
Connect calls and Talkgroup calls.
SIM Card Security
Important: Except for making emergency calls, your phone
does not function without the SIM card.
Ⅲ On/Off Settings — sets your phone’s ability to send
and receive pictures in Direct Connect calls. See
SIM Card’s PIN
You can protect access to your phone by using the SIM
card’s PIN (Personal Identification Number). When you
enable SIM PIN, you must enter the PIN each time you
power up the phone. You can change or disable the
SIM PIN.
Ⅲ Store Received Info — lets you specify a prefix,
such as a country code for international calls, to
be automatically added to phone numbers you
receive in My Info from other phones, when you
store the My Info to Contacts. Select Prefix to enter
the prefix to be added. Set Add Prefix to Ask Me to
set your phone to display a prompt asking you
whether to add the prefix as you save My Info
from other phones to Contacts.
Turning SIM PIN On and Off
1. Press /> Settings > Security > SIM PIN.
2. Select On or Off.
3. Enter the current SIM PIN.
Important: The default SIM PIN is 0000. Change your PIN to
prevent fraudulent use of the SIM Card.
4. Press Ok (left softkey).
89
Entering the PIN
Code (PUK). Follow their instructions for unblocking
your SIM PIN.
1. Press and hold @to turn on your phone.
Important: If you unsuccessfully enter the PUK code ten
times, your SIM card is permanently blocked and
must be replaced. If this happens, you get a
message to contact Nextel Customer Service.
Except for making emergency calls, your phone
does not function with a blocked SIM card.
2. When the SIM PIN screen appears, enter your
SIM PIN and press Ok (left softkey).
Important: If you enter your PIN incorrectly three times, your
SIM card is blocked. See “Unblocking the PIN”
on page 90.
Changing the PIN
Your Phone’s Lock Feature
Note: SIM PIN must be turned on in order to access this
feature.
Locking Your Phone
1. Press /> Settings > Security >
When your phone is locked, you can only make calls to
911. To lock and unlock your phone, you must enter
your phone’s four-digit lock code. If you do not know
your phone’s lock code, try 0000; if this does not work
contact Nextel Customer Service for assistance.
Change Passwords > SIM PIN.
2. Enter the current SIM PIN and press Ok (left
softkey).
3. Enter the new SIM PIN and press Ok (left softkey).
1. Press /> Settings > Security.
4. Reenter the new SIM PIN to confirm and then
press Ok (left softkey).
2. Select Phone Lock > Lock Now, enter the unlock
code, and press Ok (left softkey). (To set your
phone to lock the next time it is turned on, select
Auto Lock.)
Unblocking the PIN
If you enter your PIN incorrectly three times, your SIM
card is blocked. To unblock your SIM card, you must
contact Nextel Customer Service to get a PIN Unblock
90
Unlocking Your Phone
Locking Your Keypad
ᮣ
At the “Enter Unlock Code” prompt, enter your
unlock code and press Ok (left softkey).
When your phone is closed and in standby mode, your
keypad locks to prevent accidental key presses.
ᮣ
To lock your keypad now, press /> Settings >
Security > Keypad Lock > Lock Now, or press
/*.
Changing the Lock Code
1. Press /> Settings > Security > Change
Passwords.
ᮣ
To change how long your phone waits before it
automatically locks your keypad, press />
Settings > Security > Keypad Lock > Auto Lock and
select a time interval of 30 seconds, 1minute, 5
minutes, 10 minutes, 15 minutes, 20 minutes, or Off.
2. Select Unlock Code then enter your current unlock
code and press Ok (left softkey).
3. Enter and reenter your new lock code, pressing
Ok (left softkey) after each.
Note: If the keypad setting is set to off, your keypad will
Calling in Lock Mode
remain unlocked.
You can place calls to 911 when in lock mode.
Unlocking Your Keypad
ᮣ
To call an emergency number, dial 911and
ᮣ
To unlock your keypad, press /*.
press `.
91
Duplicate calls (same number and type of call) may
only appear once on the list.
7. Recent Calls
When you select a call to view its details, you see
information such as the name associated with the call,
the number, date, time, and duration of the call.
Note: The Recent Calls list records only calls that occur while
the phone is turned on. If a call is received while your
phone is turned off, it will not be included in the phone’s
Recent Calls list.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ If you return a call from the voicemail menu, it will not be
included in your phone’s Recent Calls list.
Calls and Call Alerts
About Recent Calls
If the number of a recent call is stored in Contacts, the
following information appears:
The Recent Calls list displays the last 20 numbers (or
Contacts entries) for calls you placed, accepted, or
missed, and for Call Alerts you have received. It also
displays My Info and contact information sent to you
from other phones. It is continually updated as new
numbers are added to the beginning of the list and the
oldest entries are removed from the bottom of the list.
ⅷ The name assigned to the number.
ⅷ The Contacts type icon associated with the number.
If the item contains more than one number or
address stored,<>surrounds the Contacts type icon.
The Direct Connect number Contacts type icon
appears when you receive a Direct Connect call or Call
Alert, even if the number is not stored in Contacts.
92
Call Alerts you have received appear as Direct Connect
calls. Like all items in the Recent Calls list, they remain
listed until you delete them or until they reach the end
of the list.
When you select My Info from other phones to view its
details, you see all the information sent.
If you receive My Info from the same phone more than
once, only the most recently sent version appears in
the Recent Calls list.
For phone calls, an additional icon appears giving
information about the call.
Contact Information From Other Phones
A call you made.
-
The Recent Calls list displays contact information sent
from other phones. This information comes from the
other phone’s Contacts list or Recent Calls list. See
A call you received.
1
A missed call. Missed calls appear on the Recent
Calls list only if you have Caller ID.
#
This icon 2appears with contact information on the
Recent Calls list.
When you select a call to view its details, you see
information such as the name associated with the call,
the number, date, time, and duration of the call.
Contact information in the Recent Calls list displays:
ⅷ The name contained in the contact information.
My Info From Other Phones
ⅷ The Contacts type icon associated with the number
or address contained in the contact information. If the
item contains more than one number or address
stored, <> surrounds the Contacts type icon.
The Recent Calls list displays My Info sent from other
phones. See “Sending My Info and Contact
This icon 3 appears with My Info sent from other
phones, along with the Direct Connect number of the
person who sent the information.
The name or Direct Connect number of the person
who sent the contact information appears as a
93
separate item on the Recent Calls list, above the
information sent. If one person sends you more than
one item of contact information, all the items appear
below the person’s name or Direct Connect number.
Recent Calls Options
Select a Recent Calls entry and press rto display the
date and time of the call, the phone number (if
available), and the caller’s name (if the number is
already in your Contacts). Press /to display the
following options:
When you select contact information to view its details,
you see the name or Direct Connect number of the
person who sent the information and all the information
in the item.
ⅷ Use Push To... to select Send My Info or Send Contact
(Direct Connect or Calls Alerts only).
If you receive contact information with the same name
from the same phone more than once, only the most
recently sent version appears in the Recent Calls list.
ⅷ Send Contact to send the contact information to
another Direct Connect user.
ⅷ Delete to delete the entry.
Viewing Recent Calls
ⅷ Delete All to delete all recent calls entries.
ⅷ Add Prepend to prepend a number to the contact
To view the Recent Calls list:
1. Press `or /> Recent Calls.
2. Scroll through the list.
ⅷ Recent Calls View to select between List View or
Picture View.
To view the details of an item on the list:
ⅷ Call Alert Queue to view the call alert list.
ᮣ
From the Recent Calls list, highlight an entry and
ⅷ Call Setup to configure the call.
press r.
ⅷ Call New Group to create a Group and place a Group
Connect call (Direct Connect or Call Alerts only).
94
4. If the item is a call, you must assign a Contacts
type to the number:
Tip: Press Create (left softkey) to begin a message to the
highlighted entry.
With the Contacts type field highlighted, scroll left
or right to display a Contacts type.
You can also view the next Recent Calls entry by pressing
the navigation key right or view the previous entry by
pressing the navigation key left.
5. To add more information to the entry (optional),
follow the applicable instructions in “Creating
Saving Items From Recent Calls
6. Press Save (left softkey).
1. From Recent Calls, highlight or select an item.
2. Press Save (left softkey).
– or –
Deleting Items From Recent Calls
To delete an item from the Recent Calls list:
1. From Recent Calls, highlight or select an item.
2. Press /> Delete.
If Save is not one of your options, press /and
then select Save or Update Contacts.
Tip: If the item you are storing is a call, Save does not appear
if the number is already stored in Contacts.
3. Press ror press Yes (left softkey) to confirm.
To delete all items on the Recent calls list:
1. Press /> Recent Calls.
3. Select [New Contact] to store the number in a new
Contacts entry, or select an entry to store the
number to an existing entry.
2. Press /> Delete All.
Note: Storing My Info or contact information from another
phone to a Contacts entry that has a name assigned to
it does not change the name of the Contacts entry.
3. Press Yes (left softkey) to confirm. Press No (right
softkey) to cancel.
95
Prepending a Number From Recent
Calls
If you need to make a call from the Recent Calls List
and you are outside your local area code, you can add
the appropriate prefix by prepending the number.
1. Highlight or select a Recent Calls entry and press
/> Add Prepend.
2. Enter the prefix and press `to call the number.
96
About Contacts
8. Contacts
Contacts stores up to 600 numbers or addresses. Each
Contacts entry can store several numbers or
addresses.
Information stored in Contacts is saved on your
SIM card.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ A Contacts entry contains:
ⅷ A name — A name is required if you are storing more
than one number or address to the entry; otherwise,
it is optional. Typically, this is the name of the person
whose contact information is stored in the entry.
ⅷ A ring tone — You can assign a ring tone to each
entry. This is the sound your phone makes when you
receive phone calls or call alerts from any of the
numbers stored in the entry.
ⅷ A Contacts type — Each number or address stored
97
Types of Contacts
Creating Contacts Entries
Each number or address stored must be assigned a
Contacts type:
Each Contacts entry can store up to 10 numbers or
addresses, and an entry’s name can contain 20
characters.
phone number
Direct Connect number
phone number
phone number
phone number
email address
phone number
phone number
Talkgroup number
Group
Mobile
DC
A
Tip: ICE – In Case of Emergency
0
To make it easier for emergency personnel to identify
important contacts, you can list your local emergency
contacts under “ICE” in your phone’s Contacts list. For
example, if your mother is your primary emergency
contact, list her as “ICE–Mom” in your Contacts list. To list
more than one emergency contact, use “ICE1–___,”
“ICE2–___,” etc.
Work1
Work2
Home
Email
Fax
i
j
k
l
n
o
r
A number or address and a Contacts type are required
for all Contacts entries. Other information is optional.
You may enter the information in any order by scrolling
through the entry details.
Pager
Talkgroup
Group
IP
After you have entered the number or address,
Contacts type, and any other optional information,
press Save (left softkey) to save the entry to Contacts.
t
IP address
q
Other
phone number
p
To cancel a Contacts entry at any time press Cancel
(right softkey) and then press Yes (left softkey) to return
to the Contacts list or press @to return to standby
mode.
98
To create a Contacts entry:
1. Press /> Contacts > [New Contact].
Ⅲ When you are finished, press r.
2. To assign a name to the entry:
6. To assign more options to the number, including
Speed # and Voice Name, select [Options] and
proceed to steps 7-9. Otherwise, skip to step 10.
Ⅲ Select Name. Enter the name and press r.
3. To assign a ring tone or picture to the name
(optional):
7. The default Speed Dial number assigned to a
phone number is displayed in the Speed # field.
This is always the next available Speed Dial
location. To assign the phone number to a different
Speed Dial location:
Ⅲ Select Ring Tone/Picture, select a ring tone or
picture, and then press Back (right softkey).
4. To assign a Contacts type to the number or
address being stored:
Ⅲ With the Speed # field highlighted, press r.
Ⅲ Highlight the Contacts type field.
Ⅲ Press Delete (right softkey) to delete the current
Speed Dial number.
Ⅲ Scroll left or right to select a Contacts type
(Mobile, DC, Work1, Work2, Home, Email, Fax,
Pager, Talkgroup, Group, IP or Other).
Ⅲ Enter the new Speed Dial number and press r.
5. To store a number or address:
8. To create a voice name for a number, select Voice
Name. Follow the prompts to record a name.
Speak clearly into the microphone.
Ⅲ Select the # field (or ID for an email address, or IP
for an IP address).
9. When you are finished, press Back (right softkey).
Ⅲ Enter the number or address. For phone
numbers, use the ten-digit format. For Direct
Connect numbers, be sure to include the
asterisks (*).
10. To add more numbers or addresses to the entry:
Ⅲ Scroll past the information you already entered.
99
Ⅲ Enter the additional information for the entry using
steps 2–9. You must assign a name to the entry, if
you have not already.
3. Select [New Contact] to store the number to a new
entry, or select an entry to store it to an existing
entry.
11. Press Save (left softkey).
4. With the Contacts type field highlighted, scroll left
or right to select a Contacts type.
Creating Pauses and Waits
5. To add more information to the entry, follow the
applicable instructions in “Creating Contacts
When storing a number, you can program your phone
to pause or wait between digits while dialing. A pause
makes your phone pause for three seconds before
dialing further. A wait makes your phone wait for your
response before dialing further.
6. Press Save (left softkey).
Viewing Contacts
This feature is useful when using voicemail or other
automated phone systems that require you to dial a
phone number and then enter an access number.
1. Press /> Contacts and then either highlight an
entry, enter the first letter of a name, or press
Search (left softkey), and enter a name. (Your
phone finds the name you entered or the nearest
match.)
For details on using pauses and waits, see “Phone
Storing Numbers Faster
2. If an entry has more than one number or address
stored, <> surrounds the Contacts type icon. Scroll
left or right to view the icon for each number stored
in the entry.
To store numbers to Contacts from standby mode:
1. Enter a phone number or Direct Connect number.
2. Press /> Store Number.
3. Press rto display the entry, and then scroll up or
down to view all information stored for the entry.
100
4. Scroll down to the open field, enter the new
number or address and press r.
Tip: To display the next or previous entry, scroll right or left.
5. Press Save (left softkey) to save the new number.
Filtering Contacts Entries
– or –
You can set Contacts to display only entries containing
Direct Connect numbers, Groups, and Talkgroups.
To assign a speed dial number or Voice Name,
select [Options] > Speed # or Voice Name.
Complete the process, press Back (right softkey)
and then press Save (left softkey) to save the entry.
ᮣ
Press /> Contacts > /> Filter > Show DC.
Select Show All to display all Contacts entries.
Finding Speed Dial Numbers
Editing Entries
ᮣ
Press /> Contacts, select an entry and select a
phone number. The speed dial number is listed
directly under the contact phone number.
1. Press /> Contacts and highlight an entry.
2. Press Edit (left softkey) or /> Edit.
Contacts Entries” on page 98 to edit the entry.
Adding a Number to an Entry
Tip: When editing or adding to entries, make sure to press
Save (left softkey) to save the changes (you may have to
press Back to display the Save option). If you press @
before pressing Save, your changes will be discarded.
2. Press Edit (left softkey) or /> Edit.
3. Highlight the number type field above an open
number and press the navigation key right or left to
select a number type.
101
You can assign speed dial numbers when you add a
new Contacts entry, when you add a new phone
number to an existing entry, or when you edit an
existing number.
Deleting Entries
1. Press /> Contacts and highlight an entry.
2. Press /> Delete Contact.
To assign a speed dial number to a new phone number:
3. Press ror press Yes (left softkey) to confirm.
1. Add a phone number to a new or to an existing
Contacts entry. (See “Creating Contacts Entries” on
page 101.)
Deleting a Number or Address
1. Press /> Contacts and highlight an entry.
2. Highlight [Options], press r, and then select
Speed #.
2. Scroll left or right to display the Contacts type to
delete.
3. Enter an available speed dial number and
3. Press /> Delete Number.
press r.
4. Press rand Yes (left softkey) to confirm.
4. Press Back (right softkey) and then press Save (left
softkey) to save the entry.
Note: If an entry contains only one number or address,
deleting the number or address deletes the entry.
To assign a speed dial number to an existing phone
number:
Assigning Speed Dial Numbers
1. Press /> Contacts and then highlight an entry.
Your phone can store up to 600 phone numbers in
speed dial locations. (For details on how to make calls
using speed dial numbers, see “Speed Dialing” on
page 27.)
2. Press Edit (left softkey) or /> Edit.
3. Select [Options] below the number, and then select
Speed #.
102
4. Enter an available speed dial number and
press r.
6. Press Back (right softkey) and then press Save
(left softkey)to save the assigned ringer.
5. Press Back (right softkey) and then press Save (left
softkey) to save the changes.
Assigning a Picture to an Entry
Note: If you attempt to assign an already in-use speed dial
location to a new phone number, a message will
appear asking if you wish to overwrite the existing
speed dial assignment. Press Yes (left softkey) to assign
the location to the new phone number and delete the
previous speed dial assignment.
Assign a picture to display when you receive a call
from an entry.
1. Press /> Contacts and then highlight an entry.
2. Press Edit (left softkey) or /> Edit.
3. Select [Ringtone/Picture ] > Picture.
Selecting a Ringer Type for an Entry
4. Scroll through available pictures and press rto
select one. (Scroll left or right to browse pictures in
the phone’s memory or on the memory card.)
Assign a ringer type to a Contacts entry so you can
identify the caller by the ringer type. (See “Ring Tones”
5. Press Back (right softkey) and then press Save
(left softkey).
1. Press /> Contacts and then highlight an entry.
2. Press Edit (left softkey) or /> Edit.
3. Select [Ringtone/Picture ] > Ringer.
4. Scroll through available ringers. (When you
highlight a ringer type, a sample ringer will sound.)
5. Press rto select a ringer.
103
ⅷ A subject — A name or number you assign to the
event.
9. Tools
ⅷ A location — The location of the event. This can also
be a phone number, Direct Connect number, or
Talkgroup.
ⅷ A start time — The start time for the event. Default is
the beginning of the day.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ⅷ A duration — The length of time the event lasts.
ⅷ A date — The date for the event. Default is the day
highlighted when the event is created.
ⅷ A repeat — For recurring events.
ⅷ A reminder — A scheduled alert for events that
include a start time.
ⅷ A ring tone for the reminder.
ⅷ A profile that your phone uses during the event.
ⅷ A Java application that starts when the event starts.
Datebook
Only subject and date are required to save an event.
Datebook stores up to 250 events. You can store events
over a thirteen month period — twelve months after and
one month before the current date.
Viewing Datebook
ᮣ
Press /> Tools > Datebook.
A Datebook event contains:
104
You can view Datebook by the day, by the week, or by
the month. You can also view the details of any event.
To see more in day view:
Scroll up and down using the navigation key.
To highlight a day in month view:
Enter the date using the keypad.
To go to today’s date:
While in Datebook, press /> Go To Today.
ᮣ
ⅷ In day view, brief information about each event for
that day appears.
ᮣ
ⅷ In week view, events appear as markers
corresponding to their times.
ⅷ In month view, days with events are marked.
To view an event:
ᮣ
To go to any date in Datebook:
1. While in Datebook, press /> Go To Date.
2. Select a date.
1. Select the day the event occurs.
2. Select the event.
To change the current view:
Creating Events
ᮣ
While in Datebook, press /and select a view.
Every Datebook event must have a subject and be
stored to a date. Other information is optional.
Note: Day view is the default setting.
Navigating Datebook
After you have entered the information, press Done (left
softkey) to store the event to Datebook.
To scroll through Datebook:
To create a Datebook event:
ᮣ
Scroll left and right using the navigation key.
– or –
1. While in datebook, press New (left softkey).
– or –
In week view and month view, press *or #.
In day view, select [New Event].
105
2. To assign a subject to the event, select Subject
and:
7. To make the event a recurring event:
Ⅲ Select Repeat and then select a repeat cycle.
Ⅲ Enter the name or enter a phone number, Direct
Connect number, or Talkgroup number.
● If the event occurs more than once a week,
select Multiple Day, and select the days.
– or –
● Press Done (left softkey).
Press Browse (left softkey) to choose from
common event names.
Ⅲ In the End field, select a date for the event to stop
recurring.
3. To assign a location to the event (optional), select
Location and enter the location or enter a phone
number, Direct Connect number, or Talkgroup
number.
8. To create a reminder for this event, select Reminder
and then select a reminder time or select Custom
to enter a reminder time.
Note: If an event has no start time, you cannot create a
4. The start time automatically assigned to an event is
the beginning of the day. To change the start time
or assign no start time, select Start and then enter
a start time or press No Time (left softkey).
reminder for it.
9. To set the ring tone for a reminder, select Ring Tone
and then select a ring tone.
10. To assign a profile for your phone to use during
the event, select Profile and then select a profile.
(Your phone switches to this profile when the event
starts and switches back to the previous profile
when the event ends.)
5. To assign a duration, select Duration and select a
duration from the list or select Custom and enter a
duration.
6. The date automatically assigned to an event is the
date that was highlighted or selected when you
began creating the event. To change the date of
the event, select Date and then enter a date.
11. To assign a Java application to start when the
event starts, select App and then select an
application. (If you created a reminder for this
106
event, your phone prompts you to start the Java
application when you get the reminder.)
5. To change more information, follow the applicable
edit the event.
12. Once you have entered all relevant information and
settings, press Done (left softkey).
6. Press Done (left softkey) to store the event.
To cancel without saving:
Deleting Events
ᮣ
Press Cancel (right softkey).
1. Select the day the event occurs.
Editing Events
2. Select the event and press /> Delete.
3. If the event is not a recurring event, press ror
To change the details of an event:
press Yes (left softkey) to confirm.
1. Select the day the event occurs.
2. Select the event and press Edit (left softkey).
– or –
If the event is a recurring event, select This Event
Only to delete only the event selected in step 2, or
select Repeat Event to delete all occurrences of the
event.
Events” on page 105 to edit the event.
To copy an event to another date:
1. Select the day the event occurs.
2. Select the event and press /> Copy.
3. Press Yes (left softkey) to confirm.
4. Enter a date and press r.
Receiving Reminders
If you created a reminder for a Datebook event, when
the reminder time occurs, your phone notifies you with
text on the display and a reminder tone.
107
To view more details about the event:
Press View (left softkey).
To dismiss the reminder:
Press Dismiss (right softkey).
Making Calls From Datebook
ᮣ
To make a phone call:
1. Highlight or select an event containing a phone
number.
ᮣ
2. Press `or press /> Call # in Event.
For Events With Java Applications
To make a Direct Connect call or Talkgroup call:
If you assigned a Java application to start when the
event starts, you can start the application when you get
the reminder.
1. Highlight or select an event containing a Direct
Connect or Talk Group number.
2. Press the DC button. (If you did not include a #
before a Talkgroup, press /> Talkgroup, and
then press the DC button.)
ᮣ
Press /> Launch.
Making Calls From Datebook and
Datebook Reminders
To send a Call Alert:
1. Highlight or select an event containing a Direct
If you stored a phone number, Direct Connect number,
or Talkgroup number in the Subject or Location field of
a Datebook event, you can call or send a Call Alert to
that number from Datebook or from the reminder.
Connect number.
2. Press /> Alert # in Event, and then press the DC
button.
If you store the same type of number (phone number
or DC/Talkgroup number) in both fields, the number in
Subject takes precedence.
108
ᮣ
Press /> Tools > My Info.
Making Calls From Datebook Reminders
Ⅲ Information displayed includes My Name (optional,
you may enter it yourself), Line 1, Line 2, Direct
Connect, Group ID (Talkgroup number), Carrier IP,
IP1 Address and IP2 Address.
To call a number:
ᮣ
Press `or press /and then select Call # in
Event.
To make Direct Connect calls or Talkgroup calls:
Press the DC button.
To send a Call Alert:
Note: If you request equipment-related transactions on your
account, Nextel Customer Service may require you to
provide specific information about your phone. Press
/while in My Info to display a submenu that includes
your phone's service status, unit information, and
phone identification numbers including IMEI, SIM ID,
and Serial Number (SN).
ᮣ
ᮣ
Press /> Alert # in Event, and then press the DC
button.
Customizing Datebook Setup
Adding a Name to My Info
1. Select /> Tools > Datebook > /> Setup.
1. Press /> Tools > My Info.
2. Press Edit (left softkey) > Name.
3. Enter a name and press r.
2. Select an option and adjust the values.
Ⅲ Options include Start View, Daily Begin, Delete
After, Time Shift, Alert Timeout and Clock.
You can also edit the information in Line 1 and Line 2,
but your changes are only temporary. The next time
your phone registers on the network, your actual phone
numbers appear again in My Info.
My Info
My Info lets you view your phone number, Direct
Connect number, and other phone information.
109
To suspend an application:
Press @.
To view your suspended applications:
Press /> Games and Apps > Suspended Apps.
Java Applications
ᮣ
Installing Applications
ᮣ
1. Press /> Games and Apps.
You can have up to three applications running at one
time — one running in the foreground and two in the
background.
2. Select an application or suite of applications.
Messages appear as the application installs.
3. Press Done (left softkey).
Resuming Applications
Running Applications
You can resume a suspended application at any time.
This brings it to the foreground.
1. Press /> Games and Apps.
2. Select an application or suite of applications. If you
have selected a suite of applications, select an
application.
To resume a suspended application:
1. Press /> Games and Apps > Suspended Apps.
2. Select an application to resume.
Tip: If you do not hear the sounds associated with the Java
application, select Settings > Volume and check the
volumes of Speaker and Earpiece.
Ending Applications
To end an application:
Suspending Applications
ᮣ
Press the appropriate softkey to end or exit the
When you suspend an application, it does not stop
running. It goes to the background so that you can run
another application in the foreground.
application or press /> End.
110
To end an application from the Suspended Apps Screen:
Deleting Applications
1. Press Games and Apps > Suspended Apps.
To delete an application:
2. Highlight an application and press End (left
softkey).
1. Press /> Games and Apps.
2. Highlight an application and press /> Deinstall.
3. Press ror Yes (left softkey) to confirm.
To end all applications:
1. Press /> Games and Apps > Suspended Apps >
/> End All.
4. When your phone has finished deleting the
application, press Done (left softkey).
2. Press ror press Yes (left softkey) to confirm.
To delete all Java applications:
3. To end all applications without letting them exit,
press EndNow (left softkey) and then press Finish
(right softkey).
1. Press /> Games and Apps.
2. Highlight Java System and press /> Delete All.
(You may need to press More [left softkey] to
display Java System.)
Downloading Applications
To run more Java applications, you can download
them into your phone.
3. Press ror press Yes (left softkey) to confirm.
To access a catalog of items available for purchase and
download:
Digital Rights Management (DRM)
When you download multimedia content available
online, such as Java applications, these items may be
subject to DRM restrictions. DRM, or digital rights
ᮣ
Press /> Games and Apps > Buy Games&Apps.
account to find a wide selection of available Java
applications and downloading instructions.
111
management, is a system that defines how copyrighted
multimedia content can be distributed and used.
To view the license of a DRM item:
1. Go to the location that contains the item.
2. Highlight the item and press /> License Info.
DRM limits items to time-based or count-based usage
settings. Time-based settings let you use the given item
for a specified interval. Count-based settings let you
use an item for a specified number of times after you
download it or for unlimited use.
Renewing DRM Licenses
Note: Java application data is stored in your phone using the
same memory space used to store messages, voice
records, pictures, ring tones, and wallpaper images.
Deleting some of these other items frees memory for
Java applications.
Managing Items
Depending on how the third-party vendor has set rights
for the given DRM item, you may be unable to perform
some of the following tasks.
1. Go to the location on your phone that contains the
item.
Viewing License Information
2. Highlight a DRM item and press Renew (left
softkey) or press /> Renew.
You can check a DRM item’s license to view the
following information:
3. Select the link to the page where you purchased
the item and then follow the vendor’s instructions
for purchasing an additional license.
ⅷ For time-based items, either the date and time the
item expires, or the number of days left.
ⅷ For count-based items, the number of credits (uses)
left or an unlimited use notice.
Deleting Items
ⅷ The name of the item’s vendor.
If you delete a DRM item that you purchased from
Nextel from your phone, you will have to purchase it
again to download it.
112
takes to calculate it) will vary depending on the
environment in which you are using the GPS feature.
Note: You cannot delete items that are DRM locked.
Under certain conditions, third-party vendors will let you
download an item multiple times within a given time
frame, even if you deleted the item. Please contact the
third-party vendor of an item to learn more about the
vendor’s download regulations.
When you make a 911 emergency call, the GPS feature
of your phone can help emergency personnel locate
you if your phone has adequate access to GPS satellite
signals and your emergency response center is
equipped to process such information.
1. Highlight a DRM item and press /> Delete.
You can also use the GPS feature to view your
approximate location. Location information appears on
the phone’s display.
2. If prompted, press Yes (left softkey).
About Expired Items
Java applications loaded on your phone can also
request your location. If your phone is connected to a
laptop computer or similar device, software running on
that device can request your location. To protect your
privacy, you can control whether these requests are
Most items will continue to display on your phone until
you delete them. You can also choose to renew the
license for an expired item.
GPS Enabled
IMPORTANT: Things to Keep in Mind
Your phone’s GPS Enabled feature uses information
from Global Positioning System (GPS) satellites orbiting
the Earth to determine the approximate geographical
location of your phone. The availability and accuracy of
this location information (and the amount of time that it
If you are using the GPS feature of your phone while
driving, please give full attention to driving and to the
road.
Where adequate signals from multiple satellites are not
available (usually because your GPS antenna cannot
113
establish a view of a wide area of open sky, such as in
underground locations, inside or between buildings, or
in dense tree cover), the GPS feature of your phone
WILL NOT WORK.
information. For this reason, and because the GPS
location information reported is only approximate or
may not be available in your location, always report
your location to the 911 operator you speak to when
making an emergency call, if able, just as you would
when using a phone without GPS capabilities.
Walking or driving very slowly may also substantially
reduce GPS performance.
Note: If you are concerned about whether your local 911
emergency response center is equipped to receive
GPS location information, contact your local authorities.
Making an Emergency Call
ᮣ
Dial 911 and press `to be connected to an
emergency response center. If you are on an active
call, you must end it before calling 911.
Viewing Your Approximate Location
ᮣ
Press /> Tools > GPS > Position.
When you make an emergency 911 call, the GPS
feature of your phone begins to calculate your
approximate location. Even where your phone has
good access to sufficient GPS satellite signals and
network assist data, it may take 30 seconds or more to
determine the approximate location. This time will
increase where there is reduced access to satellite
signals. When your approximate location is
determined, it is made available to the appropriate
emergency response center.
This displays the following information about the last
time your location was calculated:
ⅷ The time (as Greenwich Mean Time) and date that
the location was last calculated.
ⅷ The approximate location, expressed as latitude and
longitude.
ⅷ The estimated accuracy of the calculated location.
ⅷ The number of satellites used to calculate the
location. In general, more satellites make for better
accuracy.
In some cases, your local 911 emergency response
center may not be equipped to receive GPS location
114
To calculate your location again:
Press Refresh (left softkey).
ⅷ Stay in the open. The GPS feature works best where
there is nothing between your phone and a large
amount of open sky. If possible, go outside, away
from tall buildings and foliage.
ᮣ
It may take your phone several minutes to complete the
process of determining your location, during which the
phone displays “Scanning For Satellites.”
ⅷ Hold your phone to enhance reception. Signals from
GPS satellites are transmitted to your GPS antenna,
which is in your phone antenna. Hold your phone
away from your body, giving the antenna clear
access to satellite signals. Do not cover the antenna
area with your fingers or anything else.
The Position screen displays the updated information.
To cancel a location calculation before it is completed:
ᮣ
Press Cancel (right softkey) to return to the Position
screen or press @to return to standby mode.
ⅷ Stand still. If possible, stand still until your phone is
finished determining your location. Moving your
phone at a walking pace while your phone is
calculating your approximate location may
substantially decrease GPS performance.
Each time approximate location of your phone is
calculated, the latest location information is stored in
your phone. You will see this information the next time
you view the Position screen.
ⅷ In a car. When using the GPS Enabled feature in a
car, position your phone so that the GPS antenna
has good access to GPS signals through the car’s
windows. Typically, the GPS antenna has best access
to GPS signals in a car when placed near a window.
Enhancing GPS Performance
Sometimes the GPS feature of your phone may be
unable to complete a location calculation successfully.
To improve accuracy and increase your chances of a
successful calculation, do the following while your
phone is determining your approximate location:
Note: Although moving your phone at a walking pace
decreases GPS performance, moving it at the speed of
a moving car does not.
115
ⅷ Stay in network coverage. The network will provide
your phone with information that helps determine
your location more quickly and accurately.
Note: Because your phone is continuously determining your
location, using the GPS feature of your phone with map
software uses the phone’s battery power quickly.
To connect your phone to your laptop or other device:
Using GPS With Map Software
1. Pull open the connector cover.
You can use the GPS feature of your phone to provide
approximate location data to a laptop computer or
similar device that is running interactive map software
such as that made by DeLorme or Microsoft. This way,
if your phone has good access to GPS signals, your
approximate position on a map can be made available
as you travel in a vehicle.
2. With the phone’s display facing up, insert a
micro-USB data cable into the charger connector.
To do this, connect your phone to your laptop (or other
device) with a data cable and set your phone to
transmit data (see “To connect your phone to your
laptop or other device:” on page 116). Your phone then
provides your approximate location to the device
running the map software, which displays your location
on a map. Your phone provides an updated location
every second and the map software displays your
changing location on its map.
3. Insert the data plug into the COM port of your
laptop or other device.
Make sure no other application is using the COM port
selected.
more details on obtaining good location information.
116
Make sure the COM port settings of your laptop or
other device are set to the following:
Memo Feature
ⅷ Bits per second: 4800
ⅷ Data bits: 8
Memo lets you store a number, make a call to that
number, and save it to Contacts.
ⅷ Parity: None
To create a memo:
ⅷ Stop bits: 1
1. Press /> Tools > Memo.
2. Enter a number and press r.
To view the memo later:
ⅷ Flow control: Hardware
To set your phone to send location information to your
laptop or other device:
ᮣ
Press /> Tools > Memo.
1. Press /> Tools > GPS > Interface.
To delete the memo:
2. Set NMEA OUT to USB or Bluetooth.
1. Press /> Tools > Memo.
Your phone is now sending location data to your
laptop or other device.
2. Press and hold Delete (left softkey) and then
press r.
To stop sending location data to your laptop or other
device:
To edit the memo:
1. Press /> Tools > Memo.
ᮣ
Set NMEA OUT to Off.
2. Press and hold Delete (left softkey) to delete the
number.
Each time you power your phone on, NMEA OUT is
automatically set to Off.
3. Enter the new number and press r.
117
To make a call to the memo number:
Voice Records
1. Press /> Tools > Memo.
A voice record is a recording you make with your
phone and can play back. You can record notes to
yourself or phone calls.
2. To make a phone call, press `. To make a Direct
Connect call, press the DC button.
To store the memo number to Contacts:
1. Press /> Tools > Memo.
Your phone can store up to 20 voice records.
Creating Voice Records
2. Press /> Store to Contacts.
1. Press /> Multimedia > VoiceRecord >
[New VoiceRec].
3. To store the number as a new entry, select
[New Contact].
2. Recite a message into the microphone.
3. When you are finished recording, press r.
To record a phone call:
– or –
To store the number to an existing entry, select the
entry.
4. With the Contacts type field highlighted, scroll left
or right to display a Contacts type for the number.
1. While on an active call, press /> Record.
2. When you are finished recording, press r.
5. To add more information to the entry, follow the
applicable instructions in “Creating Contacts
Note: Recording of phone calls is subject to applicable laws
regarding privacy and recording of phone
conversations.
6. Press Save (left softkey).
118
Playing Voice Records
Deleting Voice Records
1. Press /> Multimedia > VoiceRecord.
To delete an unlocked voice record:
2. Highlight a voice record and press r.
1. Press /> Multimedia > VoiceRecord.
2. Highlight a record and press /> Delete.
3. Press ror Yes (left softkey) to confirm.
To delete all unlocked voice records:
3. To stop the voice record while it is playing,
press r.
Tip: To fast forward, scroll right. To rewind, scroll left. To pause
or resume, press any number key.
1. Press /> Multimedia > VoiceRecord.
2. Highlight a record and press /> Delete All.
3. Press ror Yes (left softkey) to confirm.
Labeling Voice Records
When you create a voice record, it is labeled with the
time and date it was recorded. You can rename it with
a custom label.
Locking Voice Records
1. Press /> VoiceRecord.
When you lock a voice record, it cannot be deleted
until you unlock it.
2. Highlight a record and press Label (left softkey).
3. Enter a label and press r.
1. Press /> Multimedia > VoiceRecord.
2. Highlight a record and press /> Lock to lock it.
Press /> UnLock to unlock a message.
When a voice record is locked, this icon X appears
next to it.
119
ⅷ Kbytes Reset — keeps a running total of the number
of kilobytes sent and received by your phone, until
you reset it.
Managing Memory
To view the amount of memory available for voice records:
1. Press /> Multimedia > VoiceRecord.
To view or reset a timer:
2. With [New VoiceRec] highlighted, press Memory
(left softkey).
1. Press /> Tools > Call Timers.
2. Select a timer and press r.
Ⅲ To reset a timer, select Phone Reset, DC/GC Reset,
or Kbytes Reset and press r. Press Reset (left
softkey). Press ror press Yes (left softkey) to
confirm.
Call Timers
Call timers measure the duration of your phone calls,
Direct Connect, or Group Connect calls, and the
number of kilobytes sent and received by your phone:
Note: The values displayed by Call Timers should not be
used for billing. Call times are estimates only.
ⅷ Last Call — displays the duration of your most recent
phone call.
ⅷ Phone Reset — keeps a running total of your phone
call minutes, until you reset it.
ⅷ Phone Lifetime — displays the total minutes of all your
phone calls.
ⅷ DC/GC Reset — keeps a running total of all of your
Direct Connect and Group Connect call minutes,
until you reset it
ⅷ DC/GC Lifetime — displays the total minutes of all
your Direct Connect and Group Connect calls.
120
Inserting the microSD Card
10. microSD Card
2. Open the memory card slot cover, and slide in the
memory card until it clicks into place.
ࡗ ࡗ ࡗ ࡗ Using a microSD Card With Your
Phone
Using the microSD Card Slot
Your phone is equipped with a microSD (Secure
Digital) memory card slot to expand the phone’s
available memory space. It allows you to store images,
videos, music, and voice data in your phone.
121
4. Grasp the raised edge of the microSD card and
pull the card out.
Note: Be sure to use only recommended microSD cards.
Using non-recommended microSD cards could cause
data loss and damage your phone. Your handset can
be used with Transflash or microSD memory cards.
3. Close the memory card slot cover and replace the
battery cover.
4. Your phone may prompt you to use the memory
card to store new media items, go to Music Player,
go to the Camera, go to the Media Center, or do
nothing. If you select [Do Nothing], you will return to
standby mode. Respond to the prompt now.
Removing the microSD Card
Do not remove the memory card until you select the
Remove Card option under Settings. Removing the
memory card before selecting the Remove Card option
could result in loss of data.
1. Press /> Settings > Memory Card > Remove
Note: The microSD card and its adapter can be easily
damaged by improper operation. Please be careful
when inserting, removing, or handling them.
Card.
2. Once the handset confirms that it is safe to remove
the microSD card, press OK (left softkey).
5. Close the memory card slot cover and replace the
battery cover.
3. Remove the battery cover and open the memory
card slot cover.
122
Using the microSD Adapter
Tip: If your computer has an SD card slot or if you have an SD
card adapter, you can use the microSD card and adapter
to transfer files such as audio files, pictures, and videos
directly between your computer and your microSD card.
The supplied microSD adapter allows microSD cards
to be used in SD-compatible devices such as digital
cameras, printers, and computers. Before using, you
will need to insert the microSD card into the microSD
adapter.
When you insert the card into your computer, select
Open folder to view files using Windows Explorer (or a
similar option) and drag and drop files using the available
folders.
To insert the microSD card into the microSD adapter:
ᮣ
With the label side of the microSD card facing up,
insert the card into the supplied microSD adapter,
and gently slide the card until it is fully inserted.
microSD Settings
Viewing Memory in the microSD Card
1. With the microSD card inserted, press />
Multimedia > Media Center > /> Memory Usage.
2. The following information will be displayed:
Ⅲ Used displays the amount of used memory
space.
To remove the microSD card from the microSD adapter:
Ⅲ Free displays the amount of free memory space.
ᮣ
Hold the front edge of the microSD card, and
gently pull outward to remove it from the adapter.
Ⅲ Capacity displays the capacity of the memory
card.
Ⅲ Card Files displays the number of files in the card.
123
Setting Storage Options
WARNING: The formatting procedure erases all the data on
the microSD card, after which the files CANNOT
be retrieved. To prevent the loss of important data,
please check the contents before you format the
card.
You can set your phone to store pictures, videos,
music, and audio recordings on an inserted microSD
card instead of in the phone’s memory (when
available).
1. With the microSD card inserted, press />
Settings > Memory Card > Store Media.
microSD Folders
2. To store pictures, videos, music, and audio
recordings on the memory card, select
Prefer On Card.
Displaying Your microSD Folders
All the files stored in the appropriate folders on the
microSD card are accessible through the Media
Center.
Formatting the microSD Card
1. With the microSD card inserted, press />
Multimedia > Media Center.
Formatting a microSD card permanently removes all
files stored on the card.
2. Press the navigation key left or right to display a
Card folder (All, Pictures, Audio, or Video) and
press r.
1. With the microSD card inserted, press />
Settings > Memory Card.
2. Select Format Card and press r. (A warning will
be displayed.)
3. To view or play a file, select it and press ror the
appropriate softkey.
3. If you are sure you wish to remove all the files from
your microSD card, press Yes (left softkey).
Note: The Media Center only recognizes compatible files
stored in the card’s AUDIO, VIDEO, and IMAGE folders.
124
follow the onscreen instructions to safely unplug
the USB cable.
Connecting Your Phone to Your
Computer
Important Connection Information
Before using your phone’s mass storage capabilities,
you need to prepare your phone’s data services to
synchronize with your desktop or laptop computer.
Once the phone is connected to the computer, you can
transfer your data to or from the microSD card.
ⅷ No driver installation is required for Windows 2000/
ME/XP/Vista users. If you use Windows 98/98SE, you
have to download and install the USB Mass Storage
Driver from the Nextel website at www.nextel.com.
ⅷ To avoid loss of data, DO NOT remove the USB
cable, the microSD card, or the battery while files are
being accessed or transferred.
1. With the microSD card inserted, press />
Settings > Connections > USB.
2. Highlight Memory Card Access and press r.
ⅷ DO NOT use your computer to change or edit folder
or file names on the microSD, and do not attempt to
transfer large amounts of data from the computer to
the microSD card. Doing so may cause the microSD
card to fail.
Note: To allow applications to access you phone,
press /> Settings > Connections > USB >
Application Access.
3. Connect your phone to your computer using a
compatible USB cable. (Wait for the connection to
be completed. When connected, the host
ⅷ DO NOT turn off or restart your computer, or put it
into standby mode, while using a mass storage
device. Doing so will result in loss or damage of data.
computer will automatically detect your phone.)
ⅷ If you connect a mass storage device to a peripheral
device, your device may not work properly.
To remove the connection:
ᮣ
When you have finished transferring data, click the
USB device icon on your computer’s taskbar, and
125
Tip: To take a self-portrait, activate the camera and then close
the phone. Use the external screen to aim the lens, and
then press the speaker button ()) to take the picture.
11. Camera
Ⅲ Press Send (left softkey) to send the picture in an
MMS message, Discard (right softkey) to discard
the picture and return to the camera, rto save
the picture and return to camera, or press /for
the following options:
ࡗ ࡗ ࡗ ࡗ ●
Send Via... to send the picture via Direct Send
(PTT), Bluetooth, or Messaging (MMS).
●
●
Save [OK] to save the picture.
Taking Pictures
Set As Caller ID to assign the picture to a
contact. Select a contact and press r.
Taking pictures with your phone’s built-in camera is as
simple as choosing a subject, pointing the lens, and
pressing a button.
●
●
●
●
Set As Wallpaper to use the picture as your
phone’s wallpaper.
Media Center to save the picture to the Media
Center and open the Media Center.
1. With the phone open, press ?to activate camera
mode.
Remove Card to enable the memory card
removal.
2. Using the display screen as a viewfinder, aim the
camera lens at your subject.
Memory Usage to see the amount of used and
available memory on your phone.
3. Press Capture (left softkey), ?or runtil the
shutter sounds.
126
●
●
Memory Card to access the memory card
menu.
ⅷ Picture Quality to select the picture quality between
Normal or Fine.
Camera Setup to set the camera default
settings for Ask for Name, Shutter Sound,
Default Size, Default Quality and GPS Tag.
ⅷ Picture Size to select the picture size.
ⅷ White Balance to select a white balance setting.
ⅷ Exposure Control to adjust the exposure.
ⅷ Style to set the picture effect.
Camera Options
ⅷ Memory Usage to verify memory usage.
ⅷ Memory Card to access the memory card menu.
ⅷ Camera Setup to set the camera default settings.
With the phone in camera mode, press /to display
additional camera options:
ⅷ [Help] to open a help file.
Setting the Self Timer
ⅷ Record Video to switch to video mode. (See
1. From camera mode, press /> Self Timer.
“Recording Videos” on page 128 for details.)
ⅷ Media Center to go to the Media Center to review
your saved pictures.
2. Highlight a delay length (10 seconds, 15 seconds or
20 seconds) and press r.
Zoom” on page 128 for details.)
3. Press Capture (left softkey) or rwhen you are
ready to start the timer. (The lower portion of the
display screen displays the countdown time.)
ⅷ Remove Card to safely remove the memory card.
ⅷ Spotlight to turn the flash on or off.
4. Get ready. The camera will automatically capture
the picture when the timer runs down.
ⅷ Self Timer to activate the camera’s timer. (See
“Setting the Self Timer” on page 127 for details.)
To cancel the self timer after it has started:
ⅷ GPS Tag the option to turn GPS Tag on or off.
ᮣ
Press Cancel (right softkey).
127
Ⅲ GPS Tag: If this option is On, pictures will be
tagged with the geographic location of where they
were taken.
Using the Zoom
Depending on your resolution settings, you can adjust
the zoom from 1x to 4x.
To adjust the zoom:
Recording Videos
1. While in camera mode, press /> Zoom.
2. Select from 1X, 2X or 4X.
In addition to taking pictures, you can also record, view,
and send videos with the phone’s video camera.
Camera Setup
To record a video:
Set your camera’s resolution and default size in the
Camera Setup menu.
1. Press /> Multimedia > Camcorder to activate
video mode. (Additional video options are
available through the video mode Options menu.
information.)
1. Press ?> /> Camera Setup.
2. Select an option and press r.
Ⅲ Ask for Name: Select On for the camera to prompt
you to enter a new file name when saving a
picture.
2. Using the display screen as a viewfinder, aim the
lens at your subject.
3. Press Record (left softkey) or rto begin
recording.
Ⅲ Shutter Sound: Select an option and press r.
Ⅲ Default Size: Select a size and press r.
4. Press ror Stop (left softkey) to stop recording.
Ⅲ Default Quality: Highlight Normal or Fine and
press r.
Ⅲ To return to camcorder mode to take another
video, press rto save or Discard (right softkey)
to delete the video.
Ⅲ Spotlight Setting: Allows you to set the spotlight to
Always On.
128
5. Press /for more options:
ⅷ Video Size to select the video size.
Ⅲ Review to play back the video.
ⅷ Video Length to select the video length.
Ⅲ Send Via... to send the video via Bluetooth or
Messaging (MMS).
Ⅲ Short (for messages) restricts the length of the
video to a size that can be sent via messaging.
Ⅲ Save [OK] to save the video.
Ⅲ Maximum lets you take as long a video as
available memory space allows.
Ⅲ Media Center to go to the Media Center to review
your saved videos.
ⅷ Memory Usage to verify memory usage.
Ⅲ Remove Card to enable the memory card removal.
ⅷ Memory Card to access the memory card menu.
ⅷ Camera Setup to set the camcorder default settings.
Ⅲ Memory Usage to verify memory usage.
Ⅲ Camera Setup to set the camcorder default
settings.
Selecting Video Settings
1. From video mode, press /> Camera Setup.
Video Mode Options
2. Select an option and press r:
With the phone in video mode, press /to display
additional options:
Ⅲ Ask for Name: Select On for the camcorder to
prompt you to enter a new file name when saving
a video file.
ⅷ Media Center to go to the Media Center to review
your saved videos.
Ⅲ Shutter Sound: Select an option and press r.
ⅷ Capture Picture to switch to picture mode.
ⅷ Zoom to zoom in on a subject.
Ⅲ Default Video Size: to set a video’s default size.
Ⅲ Spotlight Setting: Allows you to set the spotlight to
Always On.
ⅷ Remove Card to enable the memory card removal.
ⅷ Spotlight to turn the spotlight on or off.
129
Card Folder
Storing Pictures and Videos
You can save pictures and videos directly to the
microSD card. Several pictures can be stored and
managed in each folder on the microSD card,
depending on its capacity.
Your phone’s pictures, video, and audio recordings
storage area is called the Media Center. There are two
types of folders in the Media Center: Phone and Card.
To review your pictures and videos on the microSD card:
Setting Storage Options
1. Press /> Multimedia > Media Center.
1. Press /> Settings > Memory Card > Store Media.
2. Use the navigation keys to select Card: All and view
saved pictures and videos.
2. Select On Phone or Prefer on Card.
Phone Folder
Phone Folder and Card Folder Options
Your phone’s internal storage area is called the Phone
folder. From the Phone folder, you can view all the
pictures and videos you have stored there, send items
(via Direct Send, Bluetooth, or messaging), delete files,
and access additional options.
When you are highlighting a picture or video file in the
phone or microSD card folders, press /to display the
following options:
ⅷ Delete to delete the selected file.
ⅷ Lock to lock the selected file.
To review your stored pictures and videos in the phone:
ⅷ Rename to rename the selected file.
1. Press /> Multimedia > Media Center.
ⅷ Send Via... to send the file via Direct Send, Bluetooth,
or Messaging.
2. Use the navigation keys to select Phone: All and
view saved pictures and videos.
ⅷ Camera to activate Camera mode.
ⅷ Remove Card to enable the memory card removal.
130
ⅷ Set As Caller ID to display the currently highlighted
picture for incoming calls from a specific Contacts
entry. Select an entry and press r.
Ⅲ Color Adjustments to select a color setting for the
picture.
Ⅲ Resize to resize the picture.
ⅷ Set As Wallpaper to display the currently highlighted
picture as a wallpaper. Select Internal Display,
External Display, or Both and press r.
Ⅲ Borders to add a border to the picture.
Ⅲ Stamps to add a stamp to the picture.
Ⅲ Text to add text to the picture.
ⅷ Copy To Card/Phone to copy the file from the current
folder to the other.
Ⅲ Text Bubble to add a text bubble to the picture.
ⅷ Setup to Sort files (By Time or By Name), and to turn
Remember Filter on or off.
ⅷ Move To Card/Phone to move the file from the current
folder to the other.
ⅷ Delete All to delete all files in the folder.
ⅷ Filter to select the media type to view from Phone: All,
Phone: Pictures, Phone: Audio, Phone: Video, Card: All,
Card: Pictures, Card: Audio, and Card: Video.
ⅷ Set View to switch the display from Plain List View to
Thumbnail List View.
ⅷ Memory Usage to verify memory usage.
ⅷ Memory Card to go to the memory card menu.
ⅷ Edit to display the following options (pictures only):
Ⅲ Crop to crop the selected picture.
Ⅲ Rotate/Flip to rotate or flip the selected picture.
131
To turn Bluetooth on:
1. Press />Tools > Bluetooth > Setup > Power.
2. Select On and press rto enable Bluetooth.
To turn Bluetooth off:
12. Bluetooth
1. Press /> Tools > Bluetooth > Setup > Power.
2. Select Off and press rto disable Bluetooth.
To turn discoverable mode on:
ࡗ ࡗ ࡗ ࡗ ᮣ
Press /> Tools > Bluetooth > Setup >
Find Me Duration.
Turning Bluetooth On and Off
For the duration selected under Find Me Duration,
the phone will be discoverable by other devices
that are within range.
Bluetooth is a short-range communications technology
that allows you to connect wirelessly to a number of
Bluetooth devices, such as headsets and hands-free
car kits, and Bluetooth-enabled handhelds, computers,
printers, and wireless phones. The Bluetooth
communication range is usually up to approximately
30 feet. By default, your device’s Bluetooth feature is
turned off. Turning Bluetooth on makes your phone
“discoverable” by other in-range Bluetooth devices.
Bluetooth Status Indicators
The Bluetooth status indicators on your phone’s display
screen shows your Bluetooth connection status at a
glance:
No Status Indicator – Bluetooth is disabled (default
status)
B – Status indicator will blink when the phone is in
discovery mode.
132
B – Status indicator will be solid when connected to a
Bluetooth device.
Ⅲ File Transfer Help opens a help file about
transferring files via Bluetooth from your
computer.
Bluetooth Menu
Connecting Bluetooth Devices
The Bluetooth menu allows you to set up many of the
characteristics of your phone’s Bluetooth service.
Pairing and Connecting
1. Press /> Tools > Bluetooth.
1. Press /> Tools > Bluetooth > Audio Devices >
[Look for Devices] to connect to a hands-free
device.
2. Set your Bluetooth options.
Ⅲ Select Audio Devices to discover and connect to
hands-free devices.
– or –
Ⅲ Select Pair to Devices to scan for and pair your
phone to an available Bluetooth device.
Press /> Tools > Bluetooth > Pair to Devices to
pair with a device. (Your phone will display a list of
discovered in-range Bluetooth devices.)
Ⅲ Select Device History to link to devices that have
been connected to your phone.
2. Highlight a device and press r.
Ⅲ Select Setup to turn Bluetooth on and off, rename
your phone for Bluetooth, and set the time for the
Find Me command listed below.
3. Follow the prompts, including entering a PIN if
requested, and press rto complete the
connection.
Ⅲ Select Find Me to make your phone discoverable
to Bluetooth devices for a period of time.
Pairing uses a PIN to establish a trusted connection
between your phone and another Bluetooth device.
This PIN is stored for future connections.
133
To use Bluetooth during a call:
1. While in a call, press /> Use Bluetooth.
2. Select a device.
Note: Due to different specifications and features of other
Bluetooth-compatible devices, display and operations
may be different, and functions such as transfer or
exchange may not be possible with all Bluetooth-
compatible devices.
Disconnecting From a Device
Connecting to a Stored Device
1. Press /> Tools > Bluetooth > Audio Devices.
If you have previously connected to a device, the
device will be stored on your phone so you can
connect with it easily.
2. Press Drop (left softkey) and then press Yes (left
softkey).
Note: Pressing No (right softkey) when prompted exits the
1. Press /> Tools > Bluetooth > Audio Devices and
then select a device.
menu without disconnecting the device.
Understanding Bluetooth Access Settings
2. If prompted to bond with the device, press Yes (left
softkey).
A Bluetooth device can have either Automatic or Ask
security access. The first time a Bluetooth device
connects to your MOTOROLA BRUTE, you must grant
the device permission to connect. You can then
change the access setting of the device to either
Automatic or Ask.
3. If prompted, enter the Bluetooth PIN and press Ok
(left softkey). Your phone will connect to the device.
Using Bluetooth During a Call
During a call, you can connect with available Bluetooth
devices.
If you set a device to Automatic, that device can
connect automatically to your phone when it is in
range. If you set a device to Ask, that device must
Note: If the Hands Free menu contains only one device, then
your phone will automatically try to connect to that
device.
134
request permission before it can connect to your
phone.
Sending Items via Bluetooth
Devices are automatically granted permission during
the ten seconds after connecting.
Sending Contacts, Datebook Events and
Media Center Items
The default for hands-free devices, such as Bluetooth
headsets, is Automatic.
Bluetooth lets you send Contacts entries, Datebook
events, and compatible Media Center items to
connected devices.
Setting Device Details
The device history stores a list of up to 20 devices that
have connected with your phone.
Files sent or received may be up to10 MB.
You can only connect your phone to one device at a
time.
ᮣ
Press /> Tools > Bluetooth > Device History.
From the device history, highlight a device and press
Edit (left softkey) to edit the device name and change
the access settings. To delete a device, highlight it,
press /> Delete, and then press Yes (left softkey).
list of MOTOROLA BRUTE Bluetooth-compatible
devices.
Sending Contacts
Note: If you delete a device from device history, you will have
to find the device to connect with it. (See “Pairing and
1. Press /> Contacts.
2. Highlight a contact and press /> Send Via... >
Bluetooth.
3. Select a device or search for a device by selecting
[Look for Devices].
135
4. If prompted, bond with the device. Your phone
connects to the device and transfers the contact.
3. Select a device or search for a device by selecting
[Look for Devices].
4. If prompted, bond with the device. Your phone
connects to the device and transfers the file.
Sending Datebook Events
1. Press /> Tools > Datebook.
Receiving Items
2. Highlight an event and press /> Send Via....
Ⅲ For a repeating event, select This Event Only to
send only this occurrence or Repeat Event to send
all instances.
You receive a prompt when your phone has an
incoming transfer.
ᮣ
Press Accept (left softkey) to accept the transfer or
3. Select Bluetooth.
press Reject (right softkey) to reject the transfer.
4. Select a device or search for a device by selecting
Note: Media files transferred from a PC may be copied to
your microSD card’s root directory and may not be
accessible by your phone. To check the location,
connect your phone to your computer as a USB mass
storage device and move the files to the appropriate
folders.
[Look for Devices].
5. If prompted, bond with the device. Your phone
connects to the device and transfers the event.
Sending Media Center Items
You can only send audio files and pictures if they are
not forward locked and if their DRM settings do not
prevent you from sending them.
Canceling Transfers
You can cancel a transfer while in progress.
1. Press Cancel (right softkey).
1. Press /> Multimedia > Media Center.
2. Press Yes (left softkey) to cancel, or press No (right
softkey) to continue with the transfer.
2. Highlight a file and press /> Send Via... >
Bluetooth.
136
Viewing and Storing Received Items
After an incoming transfer is complete, your phone
translates the item and it appears on the display.
You can choose to either store or discard the item.
Items are stored as follows:
ⅷ Contact entries are stored to Contacts.
ⅷ Pictures and audio files are stored to their folders and
are accessible through the Media Center.
ⅷ Datebook events are stored to Datebook.
ᮣ
To store an item, press Store (left softkey).
ᮣ
To discard an item without saving it, press
Discard (right softkey).
137
ⅷ Voice records created when your phone was not in
a call.
13. Multimedia
ⅷ Musical ringtones in the list of ringtones.
ⅷ Audio files saved from MMS messages.
ⅷ Audio files (songs, recordings, podcasts) you
downloaded to your phone.
ࡗ ࡗ ࡗ ࡗ Pictures and audio files accessible through the Media
Center can be sent in MMS messages, subject to
message size limitations. See “Creating and Sending
Messages” on page 50 for information on MMS.
Viewing the Media Center
Media Center
1. Press /> Multimedia > Media Center.
The Media Center provides convenient access to all
supported multimedia files on your device or your
memory card.
2. Scroll to view the items in the Media Center.
Choosing Thumbnail View or List View
Note: The Media Center cannot read the Music and Podcast
1. Press /> Multimedia > Media Center > />
Set View.
folder from the microSD card.
All pictures stored in your phone’s memory can be
accessed through the Media Center.
2. Select Thumbnail List View or Plain List View.
The following audio recordings can be accessed
through the Media Center:
138
Filtering by Media Type
Sorting by Time or Name
ᮣ
Press /> Multimedia > Media Center > /> Filter
and select a filtering option: Phone: All, Phone:
Pictures, Phone: Audio, Phone: Video, Card: All, Card:
Pictures, Card: Audio, or Card: Video
1. Press /> Multimedia > Media Center > />
Setup > Sort.
2. Select By Time to sort by the time items were
created or By Name to sort alphabetically.
Keeping the Last Filter Setting
When you receive your phone, the Media Center is set
to sort items by time.
You can set the Media Center to show all items every
time you access it or to keep the filtering setting you
had when you last viewed it.
Forward Locked Items
Some items saved to the Media Center may be forward
locked. Forward locked items are usually copyright
protected, and they cannot be sent or shared.
ᮣ
Press /> Multimedia > Media Center > />
Setup > Remember Filter > On.
When you receive your phone, the Media Center is set
to show all items every time you access it.
You cannot remove forward locking from an item.
When you view items in the Media Center, one of these
icons appears next to each forward locked item:
Accessing Items
1. Press /> Multimedia > Media Center.
2. Highlight an item and press rto select it.
3. Scroll right or left to access additional items.
Forward locked.
u
Forward lock and locked.
v
139
When an item is locked, it cannot be deleted from the
Locking an item has no effect on its forward locking.
3. Delete the current name, enter a new name, and
press r.
Locking Items
DRM Items
When you lock an item in the Media Center, it cannot
be deleted until you unlock it.
Except for Java applications, which download to Java
Apps, the default location for any DRM items that you
download is the Media Center.
1. Press /> Multimedia > Media Center.
2. Highlight or select an item and then press />
Lock or Unlock to lock or unlock the item.
Depending on how a vendor has set rights for an item,
the item may include the following status icons.
Deleting Items
The item is a DRM item.
k
Deleting items from the Media Center means they can
no longer be accessed anywhere in your phone,
including the list of ringtones, the list of voice records,
and Contacts.
The DRM item has expired.
l
All DRM items are forward locked. As with other items
in the Media Center, you can lock DRM items. See
Deleting an Item
1. Press /> Multimedia > Media Center.
Renaming Items
2. Highlight or select an item and then press />
Delete.
1. Press /> Multimedia > Media Center.
2. Highlight or select an item and then press />
Rename.
3. Press Yes (left softkey) to confirm.
140
Deleting All Items
Pictures
You can delete all unlocked items currently in view,
depending on how Media Center filtering is set. See
“Filtering by Media Type” on page 139. If filtering is set
to show all types of Media Center items, all unlocked
items are deleted.
The Media Center lets you view pictures and send
them in MMS messages, with Nextel Direct Send, or
with Bluetooth. You can also assign them to Contacts
entries or set them as your phone’s wallpaper.
Viewing Pictures
1. Press /> Multimedia > Media Center.
2. Press /and then select Delete All.
3. Press Yes (left softkey) to confirm.
ᮣ
To view a picture, highlight it from the list of items
in the Media Center and press r.
If your phone is set to show thumbnails, a thumbnail of
each picture appears next to the picture in the list of
items. If your phone is not set to show thumbnails, this
icon a appears next to the picture.
Tip: If you delete items you have purchased and downloaded,
including DRM items, you will usually have to repurchase
the item if you decide you want it back. Certain DRM
vendors may not charge you to download an item
multiple times within a given time frame. Please contact
the vendor for details.
To see a larger or smaller view of the picture you are
viewing:
ᮣ
Press /> Zoom and select a setting.
Viewing Memory Usage
If the picture does not fit in the display, use the
navigation key to view different parts of the picture.
1. Press /> Multimedia > Media Center.
2. Highlight or select any item in the Media Center.
3. Press /> Memory Usage.
Sending Pictures in a Message
1. Highlight or select a picture and then press Send
(left softkey) or press /> Send Via... > Messaging.
To free memory, delete items.
141
Sending Messages” on page 50.) The picture you
selected is automatically attached.
Setting Pictures as Wallpaper
ᮣ
Highlight or select a picture and press />
Set As Wallpaper.
Sending Pictures With Direct Send
My Music
1. Highlight or select a picture and press />
Send Via... > Direct Send.
My Music groups your audio files into folders and lists.
When you select an audio file to play, My Music plays
the file and then plays the other audio files grouped
with it.
2. Select A Contact or A Recent Call and select an
available recipient.
3. Press the DC button to send the picture.
In addition to music, My Music plays podcasts that you
have downloaded to your computer and then saved on
your memory card.
Sending Pictures With Bluetooth
You must set up your phone to send items
using Bluetooth before you can send a picture.
If you receive calls or notifications while playing an
audio file with My Music, the audio file pauses and a
prompt asks you to accept or ignore the incoming call
or alert.
1. Highlight or select a picture and press />
Send Via... > Bluetooth.
2. Select a device or search for a device by selecting
[Look for Devices].
Accessing My Music
3. If prompted, bond with the device. Your phone
connects to the device and transfers the picture.
1. Press /> Multimedia > My Music to launch the My
Music player.
142
2. Press the navigation key up or down to select your
music.
ⅷ Podcasts — Podcast episodes grouped alphabetically
by program. Episodes are sorted by date.
ⅷ Other — Other songs group alphabetically.
3. Press rto play music.
If there is not enough album, artist, or genre data
associated with a file, it is grouped as “Unknown”.
Exiting My Music
ᮣ
To exit My Music, press Exit (right softkey). (If Exit is
not an option, press Back [right softkey] until it is.)
Naming Audio Files
File names can include up to 255 characters, including
the file format extension (for example, mp3). Only the
first 32 characters will be displayed. If a file name is
longer than 255 characters, it will not be visible on the
player and cannot be played. In this case, you will need
to rename the file and resave it to the memory card.
How Audio Files Are Organized
My Music groups audio files on the memory card into
folders and lists. Unless the phone determines a file is
a podcast, it treats all audio files as songs.
When you access My Music, you see that the audio
files are grouped into these folders:
Playing Audio Files
ⅷ Songs — All audio files on the memory card (except
Note: Audio File Formats: My Music does not support all
audio file formats or bit rates/sampling rates. Supported
extensions include .3ga, .3gp, .aac, .amr, .au, .awb, .imy,
.m4a, .mid, .midi, .mmf, .mp3, .mp4, .mpga, .mxmf, .ra,
.ram, .rm, .smf, .wav, .wma, .xmf, .xmf0, and .xmf1.
podcasts), listed alphabetically by title.
ⅷ Playlists — Folders and lists you have created. The
default playlist is Favorites.
ⅷ Albums — Songs grouped by album title.
ⅷ Artists — Songs grouped by alphabetically by artist
and title.
1. Press /> Multimedia > My Music.
2. Highlight a folder.
ⅷ Genres — Songs grouped by genre.
143
Pause and Resume
Tip: The Songs folder contains all the audio files, except
podcasts, on the memory card in a single list.
ᮣ
To pause a playing audio file, press Pause (left
softkey).
To quickly navigate through lists, enter the first letter of a
file or folder to skip to the entries beginning with that letter.
ᮣ
To resume playing a paused audio file, press Play
(left softkey).
3. To play the first audio file in the folder, press Play
(left softkey). (If the folder you scrolled to contains
subfolders, this plays the first audio file in the first of
these subfolders.)
Skip to Next and Skip to Previous
ᮣ
To skip to the next audio file, press the navigation
key to the right.
– or –
ᮣ
To skip to the previous audio file, press the
navigation key to the left.
Press rto view the contents of the folder. Then
highlight a file and press Play (left softkey) or press
rto play it.
Fast-Forward and Rewind
Any time you are viewing a list of folders with My Music,
you can highlight a folder and press Play (left softkey)
to start playing the contents of that folder or press rto
view the contents of the folder.
ᮣ
To fast-forward a playing audio file, press and hold
the navigation key to the right.
ᮣ
To rewind a playing audio file, press and hold the
navigation key to the left.
Any time you are viewing a list of audio files, you can
highlight a file and press Play (left softkey) to play it.
Adjusting the Volume
Press Back (right softkey) to return to the previous view.
ᮣ
To adjust the volume, use the volume button.
144
Ⅲ One to repeat the current song.
Playing Music in the Background
Ⅲ Off to turn repeat off.
Your phone can continue to play music in the
background while you are accessing other features.
3. Press Back (right softkey) to return to the previous
screen.
To play music in the background:
To set shuffle:
ᮣ
With music playing, press /> Hide Player.
1. While viewing a list, viewing audio file details, or
The music player continues playing and the display
returns to standby mode. To return to the music player,
press Music (right softkey).
viewing visuals, press /> Setup.
2. Highlight Shuffle and then press the navigation key
right or left to select On or Off.
Playing a List and Using Repeat and Shuffle
3. Press Back (right softkey) to return to the previous
screen.
You can play audio files in a selected list in order
(default), you can select the Repeat option to have a list
or song repeat automatically, or you can select the
Shuffle option to have the files play continuously in
random order.
DRM Items
Some of the audio files on the memory card may be
DRM (digital rights management) items. When a DRM
items has expired, you can no longer play it.
To set repeat:
1. While viewing a list, viewing audio file details, or
If you highlight an audio file that is expired and try to
play it, a message saying you cannot play it appears. If
you play a list containing an expired audio file, My
Music skips over the expired item and no message is
displayed.
viewing visuals, press /> Setup.
2. Highlight Repeat and then press the navigation key
right or left to select an option:
Ⅲ All to repeat the list from the beginning.
145
Editing a Playlist
Working With Playlists
After you have created a playlist, you can change its
name, add audio files, remove audio files, and change
the order of the audio files.
Playlists let you group audio files that you’d like to hear
together. Adding or removing songs from playlists, or
deleting entire playlists, does not copy, move, or delete
files from your memory card.
1. Press /> Multimedia > My Music > Playlists.
2. Highlight a playlist and press /> Edit Playlist.
3. Make your changes and press Save (left softkey).
Creating a Playlist
1. Press /> Multimedia > My Music > Playlists >
[Create New] > Name.
Reordering a Playlist
2. Enter a name and press r.
You can change the order of the audio files on a
playlist.
Note: If you do not assign a name, the playlist is named
“Playlist” followed by the number of unnamed playlists
you have. For example, the first unnamed playlist you
create will be named “Playlist-1”.
1. Before you have saved a new playlist or while
editing a playlist, press /> Reorder Songs.
2. Highlight a title and press Grab (left softkey).
3. Select [Add Songs]. (You will see a list of available
audio files.)
3. Highlight a new location and press Insert (left
softkey).
4. Select each audio file for the playlist. A checkmark
appears next to each selected file.
4. Repeat steps 2 and 3 for all the items you are
moving.
5. When you are finished selecting files, press Done
(left softkey).
5. Press Done (right softkey) and then press Save (left
softkey).
6. Press Save (left softkey).
146
2. Highlight a playlist and press /> Delete Playlist.
3. Press Yes (left softkey) to confirm.
To delete all playlists:
Removing Files From Playlists
You can remove some or all audio files from a playlist.
To remove a file from a playlist:
1. Press /> Multimedia > My Music > Playlists.
2. Press /> Delete All Playlists.
1. Before you have saved a new playlist or while
editing a playlist, press /.
2. Highlight an audio file and press />
3. Press Yes (left softkey) to confirm.
This deletes all playlists except Favorites.
Remove Song.
3. Press Save (left softkey).
Using the Favorites Playlist
To remove all files from a playlist:
The Favorites playlist is a permanent playlist. You can
add, remove, and change the order of the files, but you
cannot rename it or delete it.
1. Before you have saved a new playlist or while
editing a playlist, press /> Remove All Songs.
2. Press ror Yes (left softkey) to confirm.
You can add audio files to the Favorites playlist as you
would any other playlist.
3. Add new songs to the playlist and then press Save
(left softkey).
You can also add audio files to the Favorites playlist
using the Add to Favorites shortcut.
Note: Empty playlists cannot be saved.
To add the current audio file to Favorites:
Deleting Playlists
ᮣ
While viewing a list, viewing the details of the audio
file currently playing, or viewing visuals, press />
Add to Favorites.
To delete a playlist:
1. Press /> Multimedia > My Music > Playlists.
147
To add any audio file to Favorites:
Deleting Audio Files
1. Press /> Multimedia > My Music > Songs.
2. Highlight a file and press /> Add to Favorites.
You can delete audio files from the memory card one
at a time, by album, by artist, or by genre, or by deleting
everything in the Songs, Albums, Artists, or Genres
folders.
Podcasts
Deleting an Audio File
To access and play podcasts:
1. Press /> Multimedia > My Music > Podcasts.
1. Press /> Multimedia > My Music.
2. Select the folder containing the audio file.
2. Scroll to view individual podcast episodes or
folders containing multiple episodes of the same
program.
3. Highlight the audio file and press /> Delete Song
or Delete Podcast.
3. Press rto view the podcast episodes within a
folder or the details screen of an individual
podcast episode.
4. Press Yes (left softkey) to confirm.
Deleting an Album, Artist, or Genre
1. Press /> Multimedia > My Music.
4. To play a selected podcast, press Play (left softkey).
2. Select the folder containing the audio files: Albums,
Artists, or Genres.
3. Highlight an album, artist, or genre, and press />
Delete Album, Delete Artist, or Delete Genre.
4. Press Yes (left softkey) to confirm.
148
Deleting All Audio Files
Setting the Equalizer
Deleting everything in the Songs, Albums, Artists, or
Genres folder deletes all audio files from the memory
card.
1. From anywhere in My Music, press /> Setup >
Equalizer.
2. Select a mode and press Back (right softkey).
Viewing Visuals
1. Press /> Multimedia > My Music > Songs,
Albums, Artists, or Genres.
To view visuals instead of song details:
2. Press /> Delete Songs > /> All.
1. While viewing the details of the audio file currently
playing, press /> Setup > Visuals, and use the
navigation key to select an option.
3. Press ror Yes (left softkey) to confirm.
Deleting All Podcasts
1. Press /> Multimedia > My Music > Podcasts > /
2. Press Back (right softkey).
> Delete Podcasts.
To view song details instead of visuals:
2. Press ror Yes (left softkey) to confirm.
1. While viewing visuals press /> Setup >
Visuals > Off.
Setting Audio and Visual Options
2. Press Back (right softkey).
You can customize the sound of My Music by setting
the equalizer. You can customize the look of My Music
screen by choosing a theme or by viewing visuals
while listening to an audio file.
149
ⅷ Delete Multiple lets you choose multiple images to
delete at one time.
My Images
ⅷ Switch to Phone/Card toggles between images stored
on the phone or memory card.
The My Images application lets you easily browse, edit
and view a slideshow of images on your phone or
memory card on your internal display, or browse, view
a slideshow on the external display.
ⅷ Set as wallpaper sets the highlighted image as the
phone’s wallpaper.
ⅷ Set As Caller ID sets the highlighted image as the
caller ID for a contact.
My Images Menu
The My Images menu has many image management
features. The following options are available for existing
ⅷ Send Via Bluetooth lets you send image via Bluetooth.
images by pressing /> Multimedia > My Images > /. Viewing Images
ⅷ Edit displays several options for editing your photos
including: Crop, Rotate/Flip, Color Adjustment,
Resize, Borders, Stamps, Text, and Text Bubble.
1. Press /> Multimedia > My Images or press />
Games and Apps > My Images.
2. Press /> SlideShow to view a show of all images
in the current folder.
ⅷ SlideShow starts a slideshow containing images from
the currently highlighted image.
3. Press the navigation key left or right to scroll
through the images.
ⅷ Save as New lets you save an image with a new
name.
ⅷ Preview displays the highlighted image.
ⅷ Rename lets you rename the image.
ⅷ Delete Current deletes the highlighted image.
150
Editing Images
Viewing Videos
My Images has several options for editing your photos
including: Crop, Rotate/Flip, Color Adjustments, Resize,
Borders, Stamps, Text, and Text Bubble.
ᮣ
From the My Videos display, highlight a video and
press rto begin playback.
Ⅲ My Videos will display the video in portrait mode
by default.
ᮣ
Press /> Multimedia > My Images > /> Edit
and follow the prompts to edit the picture.
Ⅲ To change the default to landscape mode press
/> Full Screen.
My Videos
Ⅲ When viewing a video, use the rbutton to
pause or play the video playback.
The My Videos application lets you easily browse and
view video files on your phone or memory card.
Ⅲ Press and hold the navigation key to the right to
fast forward the video.
ᮣ
Press /> Multimedia > My Videos or press />
Games and Apps > My Videos.
Ⅲ Press and hold the navigation key to the left to
rewind the video.
Note: Video File Formats: My Videos does not support all
video file formats or resolutions and bit/frame rates.
Supported extensions include .3gp, .asf, .mp4, .rm,
.rmvb, .mpg, and .wmv.
My Videos Setup Menu
ᮣ
Press /> Multimedia > My Videos > /> Setup.
The My Videos Setup Menu allows you to change
settings for View, 3D Audio and Reverbs.
151
Safety and Warranty
Information
Failure to read and follow the information provided in this
phone guide may result in serious bodily injury, death, or
property damage.
S1. Important Safety
Information
General Precautions
There are several simple guidelines to operating your phone
properly and maintaining safe, satisfactory service.
ࡗ ࡗ ⅷ To maximize performance, do not touch the bottom portion
of your phone where the internal antenna is located while
using the phone.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ⅷ Speak directly into the mouthpiece.
ⅷ Avoid exposing your phone and accessories to rain or liquid
spills. If your phone does get wet, immediately turn the
power off and remove the battery.
ⅷ Do not expose your phone to direct sunlight for extended
periods of time (such as on the dashboard of a car).
ⅷ Although your phone is quite sturdy, it is a complex piece of
equipment and can be broken. Avoid dropping, hitting,
bending, or sitting on it.
ⅷ Any changes or modifications to your phone not expressly
approved in this document could void your warranty for this
equipment and void your authority to operate this
equipment.
154
Note: For the best care of your phone, only authorized personnel
should service your phone and accessories. Failure to do
so may be dangerous and void your warranty.
Tip: Purchase an optional hands-free accessory at your local
Sprint Store, or call Nextel at 1-866-866-7509.
Following Safety Guidelines
Maintaining Safe Use of and Access
to Your Phone
To operate your phone safely and efficiently, always follow any
special regulations in a given area. Turn your phone off in areas
where use is forbidden or when it may cause interference or
danger.
Do Not Rely on Your Phone for Emergency Calls
Using Your Phone Near Other Electronic Devices
Mobile phones operate using radio signals, which cannot
guarantee connection in all conditions. Therefore you should
never rely solely upon any mobile phone for essential
communication (e.g., medical emergencies). Emergency calls
may not be possible on all cellular networks or when certain
network services or mobile phone features are in use. Check
with your local service provider for details.
Most modern electronic equipment is shielded from radio
frequency (RF) signals. However, RF signals from wireless
phones may affect inadequately shielded electronic
equipment.
RF signals may affect improperly installed or inadequately
shielded electronic operating systems or entertainment
systems in motor vehicles. Check with the manufacturer or their
representative to determine if these systems are adequately
shielded from external RF signals. Also check with the
manufacturer regarding any equipment that has been added to
your vehicle.
Using Your Phone While Driving
Talking on your phone while driving (or operating the phone
without a hands-free device) is prohibited in some jurisdictions.
Laws vary as to specific restrictions. Remember that safety
always comes first.
Consult the manufacturer of any personal medical devices,
such as pacemakers and hearing aids, to determine if they are
adequately shielded from external RF signals.
Responsible driving practices can be found in “Smart Practices
www.motorola.com/callsmart.
155
When using your radio product as a traditional
two-way radio, hold the radio product in a
vertical position with the microphone one to
two inches (2.5 to 5 cm) away from the lips.
Operational Precautions
Note: Always turn off the phone in healthcare facilities, and
request permission before using the phone near medical
equipment.
If you wear a radio product on your body when
transmitting, always place the radio product in
To assure optimal radio product performance and to be sure
that human exposure to RF does not exceed the guidelines set
forth in the relevant standards, always follow these instructions
and precautions:
a Motorola approved clip, holder, holster, case or body harness.
If you do not use a body-worn accessory supplied or approved
by Motorola and are not using the radio product in the intended
use positions along side the head in the phone mode or in
front of the face in the two-way radio mode, or if you hang your
device from a lanyard around your neck, keep the device at
least 2.5 centimeters (1 inch) from your body when transmitting.
Phone Operation
When placing or receiving a phone call, hold your radio
product as you would a wireline telephone. Speak directly into
the microphone.
Approved Accessories
Two-way Radio Operation
For a list of approved Motorola accessories call 1-800-453-0920,
or visit our website at www.motorola.com/phoneaccessories.
Your radio product has been designed and tested to comply
with national and international standards and guidelines
regarding human exposure to RF electromagnetic energy,
when operated in the two-way mode (at the face, or at the
abdomen when using an audio accessory) at usage factors of
up to 50% talk/50% listen.
Turning Off Your Phone Before Flying
Turn off your phone before boarding any aircraft. To prevent
possible interference with aircraft systems, the U.S. Federal
Aviation Administration (FAA) regulations require you to have
permission from a crew member to use your phone while
the plane is on the ground. To prevent any risk of interference,
FCC regulations prohibit using your phone while the plane is in
the air.
Transmit no more than the rated duty factor of 50% of the time.
To transmit (talk), push the PTT button. To receive calls, release
the PTT button. Transmitting 50% of the time or less, is
important because this radio generates measurable RF energy
only when transmitting (in terms of measuring for standards
compliance).
156
ⅷ A choking hazard may exist for small, detachable parts.
Turning Off Your Phone in Dangerous Areas
ⅷ Improper use could result in loud sounds, possibly causing
hearing injury.
To avoid interfering with blasting operations, turn your phone
off when in a blasting area or in other areas with signs
indicating two-way radios should be turned off. Construction
crews often use remote-control RF devices to set off explosives.
ⅷ Improperly handled batteries could overheat and cause a
burn.
Do not allow children to play with your phone as they could
hurt themselves and others, damage the phone or make calls
that increase your invoice.
Turn your phone off when you’re in any area that has a
potentially explosive atmosphere. Although it’s rare, your phone
and accessories could generate sparks. Sparks can cause an
explosion or fire, resulting in bodily injury or even death. These
areas are often, but not always, clearly marked. They include:
Glass Parts
Some parts of your phone may be made of glass. This glass
could break if the product is dropped on a hard surface or
receives a substantial impact. If glass breaks, do not touch or
attempt to remove. Stop using your phone until the glass is
replaced by a qualified service center.
Ⅲ Fueling areas such as gas stations.
Ⅲ Below deck on boats.
Ⅲ Fuel or chemical transfer or storage facilities.
Ⅲ Areas where the air contains chemicals or particles such
as grain, dust, or metal powders.
Seizures/Blackouts
Ⅲ Any other area where you would normally be advised to
Some people may be susceptible to epileptic seizures or
blackouts when exposed to flashing lights, such as when
playing video games. These may occur even if a person has
never had a previous seizure or blackout.
turn off your vehicle’s engine.
Note: Never transport or store flammable gas, flammable liquids,
or explosives in the compartment of your vehicle that
contains your phone or accessories.
If you have experienced seizures or blackouts, or if you have a
family history of such occurrences, please consult with your
physician before playing video games or enabling a flashing-
lights feature (if available) on your phone.
Keep Your Mobile Device and Its Accessories Away
From Small Children
These products are not toys and may be hazardous to children.
For example:
Discontinue use and consult a physician if any of the following
symptoms occur: convulsion, eye or muscle twitching, loss of
157
awareness, involuntary movements, or disorientation. It is
always a good idea to hold the screen away from your eyes,
leave the lights on in the room, take a 15-minute break every
hour, and stop use if you are very tired.
Repetitive Motion
When you repetitively perform actions such as pressing keys or
entering finger-written characters, you may experience
occasional discomfort in your hands, arms, shoulders, neck, or
other parts of your body. If you continue to have discomfort
during or after such use, stop use and see a physician.
Caution About High Volume Usage
Battery Use and Safety
WARNING: Exposure to loud noise from any source for extended
periods of time may affect your hearing. The louder
the volume sound level, the less time is required
before your hearing could be affected.
Important: HANDLE AND STORE BATTERIES PROPERLY TO
AVOID INJURY OR DAMAGE. Most battery issues
arise from improper handling of batteries, and
particularly from the continued use of damaged
batteries.
To protect your hearing:
ⅷ Limit the amount of time you use headsets or headphones at
high volume.
ⅷ Avoid turning up the volume to block out noisy surroundings.
DON’Ts
ⅷ Turn the volume down if you can’t hear people speaking
near you.
ⅷ Don’t disassemble, crush, puncture, shred, or otherwise
attempt to change the form of your battery.
If you experience hearing discomfort, including the sensation of
pressure or fullness in your ears, ringing in your ears, or
muffled speech, you should stop listening to the device through
your headset or headphones and have your hearing checked.
ⅷ Don’t let the phone or battery come in contact with water.
Water can get into the phone’s circuits, leading to corrosion.
If the phone and/or battery get wet, have them checked by
your carrier or contact Motorola, even if they appear to be
working properly.
For more information about hearing, see our website at
direct.motorola.com/hellomoto/nss/AcousticSafety.asp (in English
only).
ⅷ Don’t allow the battery to touch metal objects. If metal
objects, such as jewelry, stay in prolonged contact with the
battery contact points, the battery could become very hot.
158
ⅷ Don’t place your battery near a heat source. Excessive heat
can damage the phone or the battery. High temperatures
can cause the battery to swell, leak, or malfunction.
Therefore:
display such as Invalid Battery or Unable to Charge, take the
following steps:
ⅷ Remove the battery and inspect it to confirm that it has a
“Motorola Original” hologram;
Ⅲ Do not dry a wet or damp battery with an appliance or
heat source, such as a hair dryer or microwave oven.
ⅷ If there is no hologram, the battery is not a Motorola battery;
ⅷ If there is a hologram, replace the battery and retry charging
it;
Ⅲ Avoid leaving your phone in your car in high
temperatures.
ⅷ If the message remains, contact a Motorola Authorized
Service Center.
DOs
Important: Motorola’s warranty does not cover damage to the
phone caused by non-Motorola batteries and/or
chargers.
ⅷ Do avoid dropping the battery or phone. Dropping these
items, especially on a hard surface, can potentially cause
damage.
ⅷ Do contact your service provider or Motorola if your phone
or battery has been damaged from dropping or high
temperatures.
WARNING: Use of a non-Motorola battery or charger may
present a risk of fire, explosion, leakage, or other
hazard.
Important: USE MOTOROLA ORIGINAL PRODUCTS FOR
QUALITY ASSURANCE AND SAFEGUARDS. To aid
consumers in identifying authentic Motorola batteries
from non-original or counterfeit batteries (that may not
have adequate safety protection), Motorola provides
holograms on its batteries. Consumers should
confirm that any battery they purchase has a
Proper and Safe Battery Disposal and Recycling
Proper battery disposal is not only important for safety, it
benefits the environment. Consumers may recycle their used
batteries in many retail or service provider locations. Additional
information on proper disposal and recycling may be found on
the Web:
“Motorola Original” hologram.
ⅷ
www.motorola.com/recycling
Motorola recommends you always use Motorola-branded
batteries and chargers. Motorola mobile devices are designed
to work with Motorola batteries. If you see a message on your
ⅷ
www.rbrc.org/call2recycle/ (in English only)
159
Disposal of Lithium Ion (LiIon) Batteries: Promptly
dispose of used batteries in accordance with local
regulations. Contact your local recycling center or
national recycling organizations for more information
on how to dispose of batteries.
counterfeit or inexpensive, aftermarket-brand batteries with
unknown or questionable manufacturing standards. Nextel is
not aware of similar problems with Nextel phones resulting
from the proper use of batteries and accessories approved
by Nextel or the manufacturer of your phone. Use only
Nextel-approved or manufacturer-approved batteries and
accessories found at Sprint Stores or through your phone’s
manufacturer, or call 1-866-866-7509 to order. They’re also
available at www.nextel.com — click Accessories. Buying the
right batteries and accessories is the best way to ensure
they’re genuine and safe.
Do not handle a damaged or leaking Li-Ion battery as you can
be burned.
WARNING: Never dispose of batteries in a fire because they may
explode.
Special Note: Be sure to dispose of your battery properly. In
some areas, the disposal of batteries in household or business
trash may be prohibited.
ⅷ In order to avoid damage, charge the battery only in
temperatures that range from 32° F to 113° F (0° C to 45° C).
ⅷ Don’t use the battery charger in direct sunlight or in high
humidity areas, such as the bathroom.
Protecting Your Battery
The guidelines listed below help you get the most out of your
battery’s performance.
ⅷ Never dispose of the battery by incineration.
ⅷ Keep the metal contacts on top of the battery clean.
ⅷ Don’t attempt to disassemble or short-circuit the battery.
ⅷ In very limited circumstances, such as where your phone
has been exposed to extreme heat Cool Down message
screens will appear. To avoid possible damage to your
battery and phone, you should follow these instructions until
the phone is within its recommended temperature range.
When your phone is in Cool Down mode, only emergency
calls may be made.
ⅷ The battery may need recharging if it has not been used for
a long period of time.
ⅷ It’s best to replace the battery when it no longer provides
acceptable performance. It can be recharged hundreds of
times before it needs replacing.
ⅷ Recently there have been some public reports of wireless
phone batteries overheating, catching fire, or exploding. It
appears that many, if not all, of these reports involve
160
ⅷ Don’t store the battery in high temperature areas for long
periods of time. It’s best to follow these storage rules:
Symbol
Definition
Your phone contains an internal
lithium ion battery.
Less than one month:
-4° F to 140° F (-20° C to 60° C)
Li Ion BATT
032378o
More than one month:
-4° F to 113° F (-20° C to 45° C)
Do not let your battery, charger, or
phone get wet.
Batteries and Chargers
Your battery, charger, or portable radio may contain symbols,
defined as follows:
Listening at full volume to music
or voice through a headset may
damage your hearing.
Symbol
Definition
Using Your Phone With a Hearing
Aid Device
032374o
Important safety information
follows.
A number of Nextel phones have been tested for hearing aid
device compatibility. When some wireless phones are used
with certain hearing devices (including hearing aids and
cochlear implants), users may detect a noise which can
interfere with the effectiveness of the hearing device.
Do not dispose of your battery or
phone in a fire.
Your battery or phone may require
recycling in accordance with local
laws. Contact your local regulatory
authorities for more information.
032375o
Some hearing devices are more immune than others to this
interference noise, and phones also vary in the amount of
interference noise they may generate. ANSI standard C63.19
was developed to provide a standardized means of measuring
both wireless phone and hearing devices to determine usability
rating categories for both.
Do not throw your battery or
phone in the trash.
161
Ratings have been developed for mobile phones to assist
hearing device users find phones that may be compatible with
their hearing device. Not all phones have been rated for
compatibility with hearing devices. Phones that have been
rated have a label with the rating(s) located on the box, and are
listed at www.motorola.com/accessibility.
your hearing aid and your phone to determine probable
usability:
ⅷ Any combined rating equal to or greater than six offers
excellent use.
ⅷ Any combined rating equal to five is considered normal use.
ⅷ Any combined rating equal to four is considered usable.
These ratings are not guarantees. Results will vary depending
on the user’s hearing device and individual type and degree of
hearing loss. If a hearing device is particularly vulnerable to
interference noise; even a phone with a higher rating may still
cause unacceptable noise levels in the hearing device. Trying
out the phone with your hearing device is the best way to
evaluate it for your personal needs.
Thus, if you pair an M3 hearing aid with an M3 phone, you will
have a combined rating of six for “excellent use.”This is
synonymous for T ratings.
Nextel further suggests you experiment with multiple phones
(even those not labeled M3/T3 or M4/T4) while in the store to
find the one that works best with your hearing aid device.
Should you experience interference or find the quality of
service unsatisfactory after purchasing your phone, promptly
return it to the store within 30 days of purchase. With the Sprint
30-day Risk-Free Guarantee, you may return the phone within
30 days of purchase for a full refund. More information about
hearing aid compatibility may be found at:
M-Ratings: Phones rated M3 or M4 meet FCC requirements
for hearing aid compatibility and are likely to generate less
interference to hearing devices than unrated phones. (M4 is the
better/higher of the two ratings.)
T-Ratings: Phones rated T3 or T4 meet FCC requirements and
are likely to be more usable with a hearing device’s telecoil (“T
Switch”or “Telephone Switch”) than unrated phones. (T4 is the
better/higher of the two ratings. Note that not all hearing
devices have telecoils in them.)
www.motorola.com/accessibility, www.fcc.gov, www.fda.gov, and
www.accesswireless.org.
Getting the Best Hearing Device Experience With
Your Phone
Hearing aid devices may also be measured for immunity to
interference noise from wireless phones and should have
ratings similar to phones. Ask your hearing health care
professional for the rating of your hearing aid. Add the rating of
To further minimize interference:
ⅷ Set the phone’s display and keypad backlight settings to
ensure the minimum time interval:
162
1. Press /> Settings > Display/Info > Backlight > Timer
or Java Timer.
schemes, and further information on Motorola recycling
activities can be found at: www.motorola.com/recycling.
2. Highlight the minimum time interval setting and press r.
Disposal of your Mobile Device Packaging and
User’s Guide
ⅷ Position the phone so the internal antenna is farthest from
your hearing aid.
Product packaging and user’s guides should only be disposed
of in accordance with national collection and recycling
requirements. Please contact your regional authorities for more
details.
ⅷ Move the phone around to find the point with least
interference.
Caring for the Environment by
Recycling
Export Law Assurances
This product is controlled under the export regulations of the
United States of America and Canada. The Governments of the
United States of America and Canada may restrict the
exportation or re-exportation of this product to certain
destinations. For further information contact the U.S.
Department of Commerce or the Canadian Department of
Foreign Affairs and International Trade.
This symbol on a Motorola product means the product
should not be disposed of with household waste.
Disposal of your Mobile Device and Accessories
Please do not dispose of mobile devices or electrical
accessories (such as chargers, headsets, or batteries) with
your household waste. These items should be disposed of in
accordance with the national collection and recycling schemes
operated by your local or regional authority. Alternatively, you
may return unwanted mobile devices and electrical
California Perchlorate Label
Some mobile phones use an internal, permanent backup
battery on the printed circuit board that may contain very small
amounts of perchlorate. In such cases, California law requires
the following label:
accessories to any Motorola Approved Service Center in your
region. Details of Motorola approved national recycling
163
Perchlorate Material – special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate. There is no special
handling required by consumers.
Product Operation
When placing or receiving a phone call, hold your mobile
device just like you would a landline phone.
If you wear the mobile device on your body, always place the
mobile device in a Motorola-supplied or approved clip, holder,
holster, case, or body harness. If you do not use a body-worn
accessory supplied or approved by Motorola—or if you hang
your mobile device from a lanyard around your neck—keep the
mobile device and its antenna at least 2.5 centimeters (1 inch)
from your body when transmitting.
Radio Frequency (RF) Energy
This section contains important information on the safe and
efficient operation of your mobile device. Read this
information before using your mobile device.
Exposure to Radio Frequency (RF) Energy
Using accessories not supplied or approved by Motorola may
cause your mobile device to exceed RF energy exposure
guidelines. For a list of Motorola-supplied or approved
accessories, visit our website at: www.motorola.com.
Your mobile device contains a transmitter and receiver. When it
is ON, it receives and transmits RF energy. When you
communicate with your mobile device, the system handling
your call controls the power level at which your mobile device
transmits.
RF Energy Interference/Compatibility
Nearly every electronic device is subject to RF energy
interference from external sources if inadequately shielded,
designed, or otherwise configured for RF energy compatibility.
In some circumstances your mobile device may cause
interference with other devices.
Your Motorola mobile device is designed to comply with local
regulatory requirements in your country concerning exposure
of human beings to RF energy.
Operational Precautions
Follow Instructions to Avoid Interference Problems
ⅷ Turn off your mobile device in any location where posted
notices instruct you to do so.
For optimal mobile device performance, and to be sure that
human exposure to RF energy does not exceed the guidelines
set forth in the relevant standards, always follow these
instructions and precautions.
ⅷ In an aircraft, turn off your mobile device whenever instructed
to do so by airline staff.
164
ⅷ If your mobile device offers an airplane mode or similar
feature, consult airline staff about using it in flight.
Additionally, the use of wireless devices and their accessories
may be prohibited or restricted in certain areas. Always obey
the laws and regulations on the use of these products.
Implantable Medical Devices
Responsible driving practices can be found in the “Smart
Practices While Driving” section in this guide (or separate
guide).
If you have an implantable medical device, such as a
pacemaker or defibrillator, consult your physician before using
this mobile device.
Operational Warnings
Obey all posted signs when using mobile devices in public
areas.
Persons with implantable medical devices should observe the
following precautions:
ⅷ ALWAYS keep the mobile device more than 20 centimeters
(8 inches) from the implantable medical device when the
mobile device is turned ON.
Potentially Explosive Atmospheres
ⅷ DO NOT carry the mobile device in the breast pocket.
Areas with potentially explosive atmospheres are often, but not
always, posted and can include fueling areas, such as below
decks on boats, fuel or chemical transfer or storage facilities, or
areas where the air contains chemicals or particles, such as
grain dust, or metal powders.
ⅷ Use the ear opposite the implantable medical device to
minimize the potential for interference.
ⅷ Turn OFF the mobile device immediately if you have any
reason to suspect that interference is taking place.
When you are in such an area, turn off your mobile device, and
do not remove, install, or charge batteries. In such areas,
sparks can occur and cause an explosion or fire.
ⅷ Read and follow the directions from the manufacturer of your
implantable medical device. If you have any questions about
using your mobile device with your implantable medical
device, consult your healthcare provider.
Knowing Radio Frequency Safety
The design of your phone complies with updated NCRP standards
described below.
Driving Precautions
The use of wireless phones while driving may cause
distraction. Discontinue a call if you can’t concentrate on
driving.
In 1991–92, the Institute of Electrical and Electronics Engineers
(IEEE) and the American National Standards Institute (ANSI) joined
in updating ANSI’s 1982 standard for safety levels with respect to
165
human exposure to RF signals. More than 120 scientists, engineers
and physicians from universities, government health agencies and
industries developed this updated standard after reviewing the
available body of research. In 1993, the Federal Communications
Commission (FCC) adopted this updated standard in a regulation.
In August 1996, the FCC adopted hybrid standard consisting of the
existing ANSI/IEEE standard and the guidelines published by the
National Council of Radiation Protection and Measurements
(NCRP).
regarding exposure of human beings to radio frequency
electromagnetic energy (EME):
ⅷ United States Federal Communications Commission, Code
of Federal Regulations; 47 CFR part 2 sub-part J.
ⅷ American National Standards Institute (ANSI) / Institute of
Electrical and Electronics Engineers (IEEE). C95. 1-1992.
ⅷ Institute of Electrical and Electronics Engineers (IEEE). C95.
1-2005 Edition.1
ⅷ International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
Body-Worn Operation
To maintain compliance with FCC RF exposure guidelines, if
you wear a handset on your body, use the Motorola supplied or
approved carrying case, holster or other body-worn accessory.
If you do not use a body-worn accessory, ensure the antenna is
at least 2.5 centimeters from your body when transmitting. Use
of non-Motorola-approved accessories may violate FCC RF
exposure guidelines.
ⅷ Ministry of Health (Canada). Safety Code 6. Limits of Human
Exposure to Radio frequency Electromagnetic Fields in the
Frequency Range from 3 kHz to 300 GHz, 1999.
ⅷ Australian Communications Authority Radio
communications (Electromagnetic Radiation - Human
Exposure) Standard 2003.
ⅷ ANATEL, Brazil Regulatory Authority, Resolution 303 (July 2,
2002) “Regulation of the limitation of exposure to electrical,
magnetic, and electromagnetic fields in the radio frequency
range between 9 kHz and 300 GHz.” “Attachment to
Resolution 303 from July 2, 2002.”
Your Motorola phone is designed to comply with local
regulatory requirements in your country concerning exposure
of human beings to RF energy.
For more information about RF exposure, visit the FCC website
at www.fcc.gov.
Portable Radio Product Operation and EME Exposure
ⅷ Your Motorola radio product is designed to comply with the
following national and international standards and guidelines
1.The information provided in this document supersedes the
general safety information in user’s guides published prior to
May 1, 2006.
166
multiple power levels so as to use only the power required to
reach the network. In general, the closer you are to a wireless
base station, the lower the power output.
Specific Absorption Rate
Your MOTOROLA BRUTE wireless phone meets the
governmental requirements for exposure to radio waves.
Before a phone model is available for sale to the public in the
U.S. and Canada, it must be tested and certified to the FCC
and Industry Canada that it does not exceed the limit
established by each government for safe exposure. The tests
are performed in positions and locations (e.g., at the ear and
worn on the body) submitted to the FCC and available for
review by Industry Canada. The highest SAR value for this
model phone when tested for use at the ear is 0.59 W/kg, and
when worn on the body, as described in this user guide, is
0.86 W/kg. Body-worn measurements can differ, depending
upon available accessories and regulatory requirements. The
SAR information includes the Motorola testing protocol,
assessment procedure, and measurement uncertainty range
for this product.
Your wireless phone is a radio transmitter and receiver. It is
designed and manufactured to not exceed limits for exposure
to radio frequency (RF) energy set by the Federal
Communications Commission (FCC) of the U.S. Government
and by the Canadian regulatory authorities. These limits are
part of comprehensive guidelines and establish permitted
levels of RF energy for the general population. The guidelines
are based on standards that were developed by independent
scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include a
substantial safety margin designed for the safety of all persons,
regardless of age or health, and to account for any variations in
measurements.
The exposure standard for wireless mobile phones employs a
unit of measurement known as the Specific Absorption Rate
(SAR). The SAR limit set by the FCC and by the Canadian
regulatory authorities is 1.6 watts per kilogram (W/kg),
averaged over one gram of tissue. Tests for SAR are conducted
using procedures accepted by the FCC and by Industry
Canada with the phone transmitting at its highest certified
power level in all tested frequencies. Although the SAR is
determined at the highest certified power level, the actual SAR
level of the phone while operating can be below the maximum
value. This is because the phone is designed to operate at
While there may be differences between the SAR levels of
various phones and at various positions, they meet the
governmental requirements for safe exposure. Please note that
improvements to this product model could cause differences in
the SAR value for later products; in all cases, products are
designed to be within the guidelines.
Additional information on SAR can be found on the Cellular
Telecommunications & Internet Association (CTIA) website:
www.phonefacts.net or the Canadian Wireless
Telecommunications Association (CWTA) website: www.cwta.ca.
167
Owner’s Record
Patent and Trademark Information
The model number, regulatory number, and serial number are
located on a nameplate inside the battery compartment.
Record the serial number in the space provided below. This will
be helpful if you need to contact us about your phone in the
future.
MOTOROLA, the Stylized M Logo and all other trademarks
indicated as such herein are trademarks of Motorola, Inc.
® Reg. U.S. Pat. & Tm. Off. ©2009 Motorola, Inc. All rights
reserved.
Microsoft and Microsoft Internet Explorer are registered
trademarks of Microsoft Corporation.
Model: MOTOROLA BRUTE i680
Serial No.:
T9 is a trademark owned by Tegic Communications.
T9® Text Input Patent and Trademark Information.
Online Product Registration:
http://www.motorola.com/us/productregistration
This product is covered by U.S. Pat. 5,818,437, U.S. Pat.
5,953,541, U.S. Pat. 6,011,554 and other patents pending.
Java and all other Java-based marks are trademarks or
registered trademarks of Sun Microsystems, Inc. in the U.S. and
other countries.
Product registration is an important step toward enjoying your
new Motorola product. Registration permits us to contact you
for product or software updates and allows you to subscribe to
updates on new products or special promotions. Registration is
not required for warranty coverage. Please retain your original
dated sales receipt, as you may need to provide it for warranty
validation in the future.
All other product names or services mentioned in this manual
are the property of their respective trademark owners.
Thank you for choosing a Motorola product.
168
Open Source Software Information
Software Copyright Notice
For instructions on how to obtain a copy of any source code
being made publicly available by Motorola related to software
used in this Motorola mobile device you may send your request
in writing to:
The Motorola products described in this manual may include
copyrighted Motorola and third party software stored in
semiconductor memories or other media. Laws in the United
States and other countries preserve for Motorola and third party
software providers certain exclusive rights for copyrighted
software, such as the exclusive rights to distribute or reproduce
the copyrighted software. Accordingly, any copyrighted
software contained in the Motorola products may not be
modified, reverse-engineered, distributed, or reproduced in any
manner to the extent allowed by law. Furthermore, the
purchase of the Motorola products shall not be deemed to
grant either directly or by implication, estoppel, or otherwise,
any license under the copyrights, patents, or patent
MOTOROLA, INC.
OSS Management
600 North US Hwy 45
Libertyville, IL 60048
USA
The Motorola website opensource.motorola.com also contains
information regarding Motorola’s use of open source.
Motorola has created the opensource.motorola.com to serve as a
portal for interaction with the software community-at-large.
applications of Motorola or any third party software provider,
except for the normal, non-exclusive, royalty-free license to use
that arises by operation of law in the sale of a product.
To view additional information regarding licenses,
acknowledgments and required copyright notices for open
source packages used in this Motorola mobile device, please
press /> Games and Apps > Open Source Notices.
169
If you have further questions regarding how use of your phone
may impact your privacy or data security, please contact
Motorola.
Privacy and Data Security
Motorola understands that privacy and data security are
important to everyone. Because some features of your phone
may affect your privacy or data security, please follow these
recommendations to enhance protection of your information:
Smart Practices While Driving
Drive Safe, Call Smart SM
ⅷ Monitor access: Keep your phone with you and do not leave
it where others may have unmonitored access. Lock your
device’s keypad where this feature is available.
Check the laws and regulations on the use of mobile devices
and their accessories in the areas where you drive. Always
obey them. The use of these devices may be prohibited or
restricted in certain areas. Contact www.motorola.com/callsmart
for more information.
ⅷ Keep software up to date: If Motorola or a software/
application vendor releases a patch or software fix for your
phone which updates the device’s security, install it as soon
as possible.
Your mobile device lets you communicate by voice and data—
almost anywhere, anytime, wherever wireless service is
available and safe conditions allow. When driving a car, driving
is your first responsibility. If you choose to use your mobile
device while driving, remember the following tips:
ⅷ Erase before recycling: Delete personal information or data
from your phone prior to disposing of it or turning it in for
recycling. For step-by-step instructions on how to delete all
personal information from your device, please contact your
local service provider.
ⅷ Get to know your Motorola phone and its features such as
speed dial and redial. If available, these features help you to
place your call without taking your attention off the road.
ⅷ Understanding AGPS: In order to comply with emergency
caller location requirements of the FCC, certain Motorola
phones incorporate Assisted Global Positioning System
(AGPS) technology. AGPS technology also can be used in
non-emergency applications to track and monitor a user’s
location, for example, to provide driving directions. Users
who prefer not to permit such tracking and monitoring
should avoid using such applications.
ⅷ When available, use a hands-free device. If possible, add an
additional layer of convenience to your phone with one of the
many Motorola Original hands-free accessories available
today.
170
ⅷ Position your phone within easy reach. Be able to access
your phone without removing your eyes from the road. If you
receive an incoming call at an inconvenient time, if possible,
let your voice mail answer it for you.
ⅷ Use your phone to help others in emergencies. If you see an
auto accident, crime in progress, or other serious emergency
where lives are in danger, call 911 or other local emergency
number, as you would want others to do for you.*
ⅷ Let the person you are speaking with know you are driving; if
necessary, suspend the call in heavy traffic or hazardous
weather conditions. Rain, sleet, snow, ice, and even heavy
traffic can be hazardous.
ⅷ Call roadside assistance or a special non-emergency
wireless assistance number when necessary. If you see a
broken-down vehicle posing no serious hazard, a broken
traffic signal, a minor traffic accident where no one appears
injured, or a vehicle you know to be stolen, call roadside
assistance or other special non-emergency wireless
number.*
ⅷ Do not take notes or look up phone numbers while driving.
Jotting down a “to do” list or going through your address
book takes attention away from your primary responsibility,
driving safely.
* Wherever wireless phone service is available
ⅷ Dial sensibly and assess the traffic; if possible, place calls
when your car is not moving or before pulling into traffic. If
you must make a call while moving, dial only a few numbers,
check the road and your mirrors, then continue.
ⅷ Do not engage in stressful or emotional conversations that
may be distracting. Make people you are talking with aware
you are driving and suspend conversations that can divert
your attention away from the road.
ⅷ Use your phone to call for help. Dial 911 or other local
emergency number in the case of fire, traffic accident, or
medical emergencies.*
171
Motorola Limited Warranty
for the United States and Canada
S2. Manufacturer’s Warranty
What does this Warranty Cover?
Subject to the exclusions contained below, Motorola, Inc.
warrants its telephones, pagers, messaging devices, and
consumer and professional two-way radios (excluding
commercial, government or industrial radios) that operate via
Family Radio Service or General Mobile Radio Service,
Motorola-branded or certified accessories sold for use with
these Products (“Accessories”) and Motorola software
contained on CD-ROMs or other tangible media and sold for
use with these Products (“Software”) to be free from defects in
materials and workmanship under normal consumer usage for
the period(s) outlined below. This limited warranty is a
consumer's exclusive remedy, and applies as follows to new
Motorola Products, Accessories and Software purchased by
consumers in the United States or Canada, which are
accompanied by this written warranty:
ࡗ ࡗ Your phone has been designed to provide you with
reliable, worry-free service. If for any reason you have a
problem with your equipment, please refer to the
manufacturer’s warranty in this section.
For information regarding the terms and conditions of service
for your phone, please visit www.nextel.com or call Nextel
Customer Service at 1-800-639-6111.
172
Products and Accessories
Products Covered
Length of Coverage
Products Covered
Length of Coverage
Products and
Accessories that are
Repaired or
The balance of the original
warranty or for ninety (90)
days from the date returned to
the consumer, whichever is
longer.
Products and
One (1) year from the date of
purchase by the first consumer
purchaser of the product unless
otherwise provided for below.
Accessories as
defined above,
unless otherwise
provided for below.
Replaced.
Decorative
Limited lifetime warranty for
the lifetime of ownership by
the first consumer purchaser
of the product.
Exclusions
Accessories and
Cases. Decorative
covers, bezels,
PhoneWrap™
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
covers and cases.
Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak are
covered by this limited warranty.
Monaural Headsets. Limited lifetime warranty for
Ear buds and boom the lifetime of ownership by
Abuse, Misuse and Accidents. Defects or damage that result
from abuse, misuse or accidents, including but not limited to:
(a) improper handling, usage, operation or storage (e.g.
operating the Product outside its permitted or intended uses
including as set forth by Motorola in the Products specification
sheets or other documentation, or failing to comply with the
Products usage documentation); abuse/neglect (e.g. broken/
bent/missing clips/fasteners/connectors); (b) contact with
liquids, water, rain, extreme humidity, heavy perspiration or
other moisture, sand, food, dirt or similar substances caused
from incorrectly securing the phone’s protective elements or
headsets that
the first consumer purchaser
of the product.
transmit mono
sound through a
wired connection.
Consumer and
Professional
Two-Way Radio
Accessories.
Ninety (90) days from the date
of purchase by the first
consumer purchaser of the
product.
173
subjecting the Products to conditions beyond their stated
specification or limits; (c) use of the Products for commercial
rental purposes; or (d) external causes or acts which are not
the fault of Motorola, including but not limited to flood, fire,
earthquake, tornado or other acts of God, are excluded from
coverage.
Software
Products Covered
Length of Coverage
Ninety (90) days
from the date of
purchase.
Software. Applies only to
physical defects in the media
that embodies the copy of the
software (e.g. CD-ROM, or
floppy disk).
Use of Non-Motorola Products and Accessories. Defects or
damage that result from the use of Non-Motorola branded or
certified Products, Accessories, Software or other peripheral
equipment are excluded from coverage.
Exclusions
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by
someone other than Motorola, or its authorized service centers,
are excluded from coverage.
Software Embodied in Physical Media. No warranty is made
that the software will meet your requirements or will work in
combination with any hardware or software applications
provided by third parties, that the operation of the software
products will be uninterrupted or error free, or that all defects in
the software products will be corrected.
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola housings, or parts, are
excluded from coverage.
Software NOT Embodied in Physical Media. Software that is not
embodied in physical media (e.g. software that is downloaded
from the internet), is provided “as is” and without warranty.
Who Is Covered?
This warranty extends only to the first consumer purchaser, and
is not transferable.
Communication Services. Defects, damages, or the failure of
Products, Accessories or Software due to any communication
service or signal you may subscribe to or use with the Products
Accessories or Software is excluded from coverage.
174
(a) a copy of your receipt, bill of sale or other comparable proof
of purchase; (b) a written description of the problem; (c) the
name of your service provider, if applicable; (d) the name and
location of the installation facility (if applicable) and, most
importantly; (e) your address and telephone number.
What Will Motorola Do?
Motorola, at its option, will at no charge repair, replace or refund
the purchase price of any Products, Accessories or Software
that does not conform to this warranty. We may use functionally
equivalent reconditioned/refurbished/pre-owned or new
Products, Accessories or parts. No data, software or
applications added to your Product, Accessory or Software,
including but not limited to personal contacts, games and
ringer tones, will be reinstalled. To avoid losing such data,
software and applications please create a back up prior to
requesting service.
What other limitations are there?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS
EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT
SHALL MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR
TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS
OF THE PURCHASE PRICE OF THE PRODUCT, ACCESSORY
OR SOFTWARE, OR FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR
LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS
OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS
OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE ABILITY OR INABILITY TO USE THE
PRODUCTS, ACCESSORIES OR SOFTWARE TO THE FULL
EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
How to Obtain Warranty Service or Other
Information
USA
Phones
1-800-453-0920
TTY
1-877-483-2840
For Accessories and Software, please call the
telephone number designated above for the
product with which they are used
You will receive instructions on how to ship the Products,
Accessories or Software, at your expense, to a Motorola
Authorized Repair Center. To obtain service, you must include:
175
Some states and jurisdictions do not allow the limitation
or exclusion of incidental or consequential damages, or
limitation on the length of an implied warranty, so the
above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights that vary from state to state or from one
jurisdiction to another.
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola
software such as the exclusive rights to reproduce and
distribute copies of the Motorola software. Motorola software
may only be copied into, used in, and redistributed with, the
Products associated with such Motorola software. No other use,
including without limitation disassembly of such Motorola
software or exercise of the exclusive rights reserved for
Motorola, is permitted.
Service and Repairs
If you have questions or need assistance, we’re here to help.
a number of customer care options. You can also contact the
Motorola Customer Support Center at 1-800-453-0920 (United
States), 1-877-483-2840 (TTY/TDD United States for hearing
impaired).
176
Volume 144
C
Index
B
Calendar
Call Alerts
Answer 41
A
Backlight 73
Charging 11
Accessories 20
Charger 20
Li-Ion Battery 20
Activation 2
Disposal 160
Installing 10
Deleting 42
Queue 42
Safety 158
Responding 42
Sending 41
Viewing 42
Airplane Mode 77
Answering Calls 22
Applications
Attachments 57
Audio Files
Deleting Received Items 137
Receiving Items 136
Sending Contacts 135
Transfers, Canceling 136
Viewing Received Items 136
Bookmarks
Accessing 67
Creating 67
Browser
Call Filtering 81
All Calls 62
Missed Calls 63
Off 62
Call Timers 120
Call Waiting 60
Off 60
Fast Forward and Rewind
Inserting in Messages 55
Pause 144
Playing 143
Resume 144
Opening 66
Restarting 68
Caller ID 59
Calls
Skip 144
Direct Connect Calls 28
Direct Talk Calls 43
177
From Contacts 29
Group Connect 30
International 64
Phone Call While in Direct
Connect 27
Adding an Entry 98
Assign a Picture to an Entry
Dialing Codes
Non-Emergency Numbers 64
Telecommunications Relay
Service 64
Digital Rights Management See
Creating 98
Phone Calls 22
Deleting 102
DRM
Talkgroup Calls 39
Using the Member ID 29
Editing Entries 101
Making Direct Connect Calls
Making Phone Calls 27
Searching 100
Direct Connect
Direct Connect Calls
Dialing 28
Camcorder
From Contacts 29
Member ID 29
Voice Name 30
Camera Setup 128
Exposure Control 127
Options 127
Voice Name 99
D
Datebook
Direct Connect Number
Direct Connect Numbers 29
Contacts 38
Creating Events 105
Deleting Events 107
Editing Events 107
Making Calls From Datebook
and Datebook Reminders
Receiving Reminders 107
Using Your Phone’s Datebook
Self Timer 127
Style 127
Talking Pictures 126
White Balance 127
Zoom 128
Groups 39
My Info 37
Pictures 34
Receiving Contacts 38
Carousel 84
Clock Display 74
178
Receiving My Info 38
Receiving Pictures 35
Alpha Mode 17
Numbers 18
Creating Groups 31
Deleting 32
Groups vs. Talkgroups 39
Icons 34
Code 44
Quick Notes 18
Making Calls 30
Private Only 45
Receiving All Calls On
Channel 46
Selecting Mode 16
Word Text Input 16
Removing Members 32
Sending With Direct Send 39
Settings 88
F
Setting Up 44
Fast Forward
Music 144
H
I
Display Screen 13
Downloading Content 68
DRM 111
Headset 78
Hearing Aid Compatibility 161
G
Games 68
Deleting Items 141
Expired Items 113
Managing Items 112
Renewing Items 112
Renewing License 112
Status Icons 140
Viewing License Information
GPS Enabled 113
Best Results 115
Emergency Calls 114
Map Software 116
Privacy Options 86
Security 87
Viewing Location 114
GPS PIN 87
Group Connect
Icons
Contacts 98
Groups 34
Status Information 13
Images
Menu 150
Slideshow 150
Viewing 150
E
Email 66
Emergency Numbers 23
End-of-Call Options 25
In-Call Options 24
International Numbers 64
Adding Group Members 31
179
J
Media Center 138
Deleting 140
Message Center 47
MMS Messages 50
Text Messaging (SMS) 59
Voicemail 49
Messages
Notifications 48
Messaging Settings
Deleting 111
Forward Locked 139
Locking Items 140
Memory 141
Pictures 141
Renaming Items 140
Viewing 138
Downloading 111
Downloading Games 68
Ending Applications 110
Installing Applications 110
Memory 112
Notification 75
Signature 77
Memo 117
Privacy 88
Resuming Applications 110
Running Applications 110
Suspending Applications 110
Calling From 118
Editing 117
Viewing 117
Adapter 123
Folders 124
Formatting 124
K
L
Memory
Key Functions 6
Java Applications 112
Media Center 141
MMS Messages 75
Ring Tones 70
Voice Records 120
Menu
Navigation 14
Selecting 15
Menu Style 74
Inserting 121
Memory 123
Removing 122
Language 85
Lock Code
Changing 91
Locking Your Keypad 91
Setting Storage Options 124
Attachments 57
Calls From 58
Locking Your Phone 90
CleanUp 77
Deleting 57
Embedded Objects 57
M
Making Calls 22
180
Going to Website 59
Locking 58
Memory 75
Outbox 56
Quick Notes 54
Receiving 56
Sending 50
My Music
Accessing 142
O
P
One Touch Direct Connect 78
Outbox 56
Owner’s Record 168
Deleting Files 148
Equalizer 149
Folders and Lists 143
Playlists 146
Repeat 145
Visuals 149
Pauses 26
Storing 100
Phone
Connecting to Computer 125
Phone (illus.) 5
Phone Number
Finding 26
Multimedia Messages
Music
N
Nextel Direct Send
Nextel Direct Talk
Fast Forward and Rewind
Pause and Resume 144
Playing 143
Saving 25
Nextel Service
With Pauses 26
Your Numbers 16
Call Answer Mode 84
Language 85
Account Passwords 3
Activation 2
Operator Services 4
Non-Emergency Numbers 64
Notepad
Volume 144
Mute 25
My Info
Editing 109
Sending 36
Shortcuts 82
181
Pictures 141
Q
R
S
Quick Notes 54
Radio Frequency 164
Tips 155
Shortcuts
Saving From Messages 59
Playlist 146
Radio Frequency 164
Call Alerts 93
Deleting Recent Calls List 95
My Info 93
Prepending a Number 96
Saving a Number 95
Remote Direct Connect Button
Creating 146
Editing 146
Favorites 147
Reordering 146
Creating 82
Deleting 83
Editing 83
Using 82
Podcasts 148
Prepend Dialing 85
Profiles 78
Silence All 72
SIM Card
Call Filtering 81
Creating 80
Deleting 80
Removing and Inserting 8
Security 89
SIM PIN 89
Resetting Your Phone 85
Rewind
Music 144
Ring Tones
Editing 80
Songs
Switching 79
Temporary 79
Viewing 78
Speakerphone 25
Speed Dial
Deleting 70
Memory 70
Setting in Contacts 99
Vibrate 72
PTT Options 88
Push To Talk 88
Assigning Numbers 102
Making a Call 27
Ringer Types 69
182
T
V
Volume
Music 144
Talkgroups 39
Join 40
Vibrate All 71
Video 128
W
Settings 88
Waits
Storing 100
Water Resistance 12
My Videos 151
TDD/TTY Devices 64
Telecommunications Relay
Service 64
Database 17
Options 129
Recording 128
Settings 129
Viewing 151
Creating 99
Voice Records
Creating 118
Mode 16
Bookmarks 67
Go to Websites 67
Launching 66
Reloading a Web Page 68
Restarting 68
Text Messaging
Three-Way Calling 61
Transmitters
TTY Devices 64
Turning Your Phone On and Off
Deleting 119
Inserting in Messages 55
Labelling 119
Locking 119
Memory 120
Wireless Data Services 66
Downloads 68
Games, Ringers, & More 68
Word Text Input 16
Playing 119
Saving From Messages 59
Voicemail
U
Unlocking Your Keypad 91
Unlocking Your Phone 91
Playing Messages 49
Retrieving 48
183
|