IMPRESSA S9/S7 avantgarde
Instructions for use
1/06
Fig. 1
Fig. 5
Fig. 9
Fig. 13
Fig. 2
Fig. 3
Fig. 7
Fig. 11
Fig. 4
Fig. 8
Fig. 12
Fig. 6
2
3
1
Fig. 10
Fig. 14
Description of the machine
16
17
18
1. Drip tray
2. Drip grate
3. Programming door
4. Rotary Switch
15
14
5. Selection key for pre-ground coffee
6. Coffee à la Carte key
7. 1 Coffee key
19
8. 2 Coffees key
13
20
21
22
12
9. 1 Espresso key
11
10. 2 Espressos key
10
9
11. ON / OFF key
8
12. Rinse key
23
24
7
13. Display dialog system
14. Water tank with handle
15. Aroma preservation cover
16. Bean tank cover
6
5
4
25
26
17. Lid for pre-ground coffee filler funnel
18. Height-adjustable coffee spout
19. Cup tray
3
20. Constant Steam key
21. Steam Portion key
22. Hot Water switch
23. Pivoting steam spout
24. 2-stage frothing jet
25. Height-adjustable hot water spout
26. Coffee grounds bin
27. Power switch
27
2 1
Contents
13.1 Programming the filter ...............................page 14
13.2 Programming your machine to the correct
1. Safety information ..............................................page
6
6
6
water hardness (only with FILTER NO) ...........page 14
1.1
1.2
Warnings ................................................page
13.3 Maintenance ............................................page 14
13.4 Programming the amount of powder for coffee
Precautions..............................................page
2. Before you start using the IMPRESSA S9/S7
and espressso............................................page 14
avantgarde ........................................................page
6
6
6
7
7
7
7
7
8
8
9
9
9
13.5 Setting the amount of water for coffee,
2.1
2.2
2.3
2.4
2.5
2.6
Checking the mains voltage ..........................page
Checking electrical fuse...............................page
Filling the water tank .................................page
Filling the bean tank...................................page
Adjusting the grinding gear ..........................page
Power switch............................................page
E
espresso and coffee à la carte........................page 15
13.6 Programming the temperature for coffee,
espresso and coffee à la carte........................page 16
13.7 Programming the water portion.....................page 16
13.8 Programming the steam portion ....................page 16
13.9 Economy mode..........................................page 17
13.10 Setting the time ........................................page 18
13.11 Programming the automatic switch-on time......page 18
13.12 Programming the automatic switch-off time .....page 19
13.13 Programming the language ..........................page 19
13.14 Programming the display.............................page 20
13.15 Information..............................................page 20
13.16 Resetting products to factory settings..............page 21
14. Maintenance......................................................page 21
14.1 Filling the water tank .................................page 21
14.2 Emptying the coffee grounds.........................page 21
14.3 Emptying the drip tray................................page 22
14.4 Drip tray missing.......................................page 22
14.5 Filling the bean tank...................................page 22
14.6 Removing stones from the grinding gear ..........page 22
14.7 Changing the filter .....................................page 22
14.8 Prompt to run cleaning cycle ........................page 22
14.9 Prompt to run decalcifying cycle....................page 23
14.10 Emptying the system ..................................page 23
14.11 General cleaning instructions ........................page 23
15. Cleaning ...........................................................page 23
16. Decalcifying.......................................................page 24
17. Disposal............................................................page 26
18. Tips for perfect coffee...........................................page 26
19. Problems ..........................................................page 27
20. Legal information ...............................................page 28
21. Technical data....................................................page 28
3. First use ...........................................................page
3.1
Cup illumination........................................page
4. Adjusting your machine to the water hardness.............page
5. Using a CLARIS plus filter cartridge........................page
5.1
5.2
Installing the filter.....................................page
Changing the filter .....................................page
6. Rinsing the machine.............................................page 10
7. Making coffee (1 espresso, 2 espressos, 1 coffee,
2 coffees)..........................................................page 10
7.1. Making coffee with pre-ground coffee powder....page 10
8. Making coffee à la carte .......................................page 11
9. Making hot water................................................page 11
10. Drawing off steam ...............................................page 12
11. Frothing milk.....................................................page 12
11.1 Frothing one portion of milk (with the
2-stage frothing jet) ...................................page 12
11.2 Frothing milk (with the 2-stage frothing
jet) ........................................................page 12
11.3 Attaching the Professional-Cappuccino Frother
to the IMPRESSA .....................................page 13
11.4 Making cappuccino and hot milk with the
Professional-Cappuccino Frother ...................page 13
11.5 Cleaning the Professional-Cappuccino Frother
and jet....................................................page 13
12. Switching the IMPRESSA S9/S7 avantgarde off.........page 13
13. Programming.....................................................page 14
5
Ⅲ Never immerse the IMPRESSA in water.
Before you begin
Congratulations on having bought this IMPRESSA S9/S7 avant-
garde!
1.2.Precautions
Ⅲ Never expose the coffee machine to weather (rain, snow, frost),
never touch the machine when your hands are wet.
In order to ensure perfect operation of your IMPRESSA, carefully
read this operating manual and keep it for future reference.
Should you need more information or meet with particular prob-
lems not specified in these operating instructions in sufficient
detail, please contact JURA Elektroapparate AG directly or your
local authorized dealer.
Ⅲ Place the IMPRESSA on a firm, level base that is resistant to any
water that may leak. Never stand on hot or warm surfaces (oven
hobs). Keep out of the reach of children.
Ⅲ If you intend not to use the machine for a longer time (holidays,
etc.), always turn off the power switch.
Ⅲ Always turn off the power switch before cleaning the machine.
You will also find useful tips on operation and maintenance
Don’t forget to check out the knowledge builder – our ani-
mated operating instructions. LEO, our assistant, will take
you through all the functions.
Ⅲ When disconnecting the mains cable, never pull on the mains
cable or the machine itself.
Ⅲ The IMPRESSA is connected to the mains supply via a mains
cable. Make sure nobody can trip over the mains cable. Keep out
of reach of children and pets.
Ⅲ Never put the coffee machine or parts of it into a dishwasher.
Ⅲ Make sure to install the machine at a place with sufficient air
circulation to prevent it from overheating.
1. Safety information
1.1 Warnings
2. Before you start using
the IMPRESSA S9/S7 avantgarde
Ⅲ Children are not aware of the dangers involved in using electric
appliances. Therefore, never leave the machine unattended with
unsupervised children around.
2.1 Checking the mains voltage
The coffee machine is preset to the correct mains voltage. Check if
your local mains supply voltage complies with the information giv-
en on the type plate on the underside of the coffee machine.
Ⅲ The coffee machine must only be used by persons who know
how to operate it.
Ⅲ Never use a defective machine or a machine with a defective
mains cable.
2.2 Checking electrical fuse
Ⅲ Never repair or open the coffee machine yourself. Repairs may
only be carried out by authorized service shops using original
spare parts and accessories.
The machine is designed for an electric current of 10 amperes.
Check if the electrical fuse has sufficient capacity.
6
Ⅲ Open the lid of the bean tank (16).
2.3 Filling the water tank
Ⅲ To adjust the grinding degree, turn the Rotary Switch (Fig. 2) to
the required position.
Only use fresh, cold water. Never fill the water tank with
milk, mineral water or other liquids.
The smaller the dots, the finer the grind
The larger the dots, the coarser the grind
Ⅲ Take out the water tank and thoroughly rinse it out with cold tap
water (Fig. 1).
E
2.6 Power switch
Ⅲ Then fill it with water and place it back into the coffee machine.
Make sure the tank is installed correctly and that it engages
properly.
Actuate the power switch (27) on your IMPRESSA before
using the machine for the first time.
We recommend that you switch off your IMPRESSA with
the power switch (27) if you intend not to use the machine
for longer periods of time (e.g.during holidays)
2.4 Filling the bean tank
To ensure your IMPRESSA will have a long service life and
to avoid repairs, please note that the grinding gear is not suit-
able for coffee beans that have been treated with additives
(e.g. sugar) during or after roasting. Coffee blends of this
type may damage the machine’s grinding gear. Repair costs
resulting from such use are not subject to the terms of guar-
antee.
3. First use
Ⅲ Press the power switch (27) on the back (bottom left) of the
machine (Fig. 3).
Ⅲ The ON / OFF key
(11) lights up to indicate that the machine
has been switched on with the power switch.
Ⅲ Open the cover of the bean tank (Fig. 2) and remove the aroma
Ⅲ Switch the machine on using the ON / OFF key
(11). The
preservation cover (15).
light of the ON / OFF key goes off.
Ⅲ Remove any dirt or foreign matter from the bean tank.
Ⅲ Open the programming door (3).
Ⅲ Fill the bean tank with coffee beans (Fig. 2), replace the aroma
Ⅲ
SPRACHE
DEUTSCH
preservation cover (15) and close the lid.
Ⅲ Turn the Rotary Switch (4) until the required language is dis-
played.
2.5 Adjusting the grinding gear
You can adjust the grinding gear to the roast of your coffee. We
recommend that you use:
Ⅲ Example:
Ⅲ
LANGUAGE
ENGLISH
a finer setting ꢀ for a lighter roast
a coarser setting ꢀ for a darker roast
Ⅲ Confirm your selection by pressing the Rotary Switch (4).
FILL SYSTEM / PRESS STEAM
The grinding degree may only be adjusted while the grinding
gear is running.
Ⅲ
7
Ⅲ Place a receptacle under the 2-stage frothing jet (24) and press
one of the Steam keys
4. Adjusting your machine to the water hardness
.
The IMPRESSA heats up water. As a result, calcification
occurs during normal use. This is indicated automatically.
The IMPRESSA must therefore be adjusted to the hardness
of the water used. Use the supplied test sticks to determine
the water hardness or contact your local waterworks.
Ⅲ The system now fills up automatically. A little water will leak
from the frothing jet.
Ⅲ
Ⅲ
Ⅲ
SYSTEM FILLING
HEATING UP
PRESS RINSE
1° German hardness is equivalent to 1.79° French hardness.
Ⅲ Place a cup under the height-adjustable coffee spout (18).
Ⅲ Press Rinse
.
The water hardness programming step is no longer displayed
if the filter is activated.
Ⅲ
MACHINE RINSING
Ⅲ Now the water lines are flushed with fresh water. A little water
will leak from the coffee spout (18).
The IMPRESSA is preset to 16°dH. This setting can be changed.
To do so, proceed as follows:
Ⅲ
SELECT PRODUCT
Ⅲ You can now make a product of your choice by pressing the
corresponding key.
Ⅲ
SELECT PRODUCT
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
If FILL BEANS appears on the display, press one of the
coffee product keys again. The grinder is not yet completely
filled with coffee beans.
Ⅲ
FILTER NO
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
For a perfect frothing result, adjust the height-adjustable
coffee spout (18) to the size of your cup (Fig. 4).
Ⅲ
HARDNESS
16°dH
Ⅲ Now press the Rotary Switch (4) to start programming.
3.1 Cup illumination
Ⅲ
16°dH
The cup illumination puts your coffee in a good light, making it a
treat for the eyes as well.
When you switch on the IMPRESSA or press any key, the cup illu-
mination is activated for 1 minute.
ⅥⅥⅥⅪⅪ
Ⅲ Now turn the Rotary Switch (4) until the required water hardness
is set.
Ⅲ
20°dH (example)
ⅥⅥⅥⅥⅪ
Ⅲ Confirm the selected setting by pressing the Rotary Switch (4).
Ⅲ
HARDNESS
20°dH (example)
8
Ⅲ Now turn the Rotary Switch (4) until the following message is
Ⅲ Fill the water tank (14) with cold, fresh tap water and place it
displayed:
back into the machine.
Ⅲ
EXIT
Ⅲ Now press the Rotary Switch (4) to leave the programming mode.
SELECT PRODUCT
Ⅲ Place a sufficiently large receptacle (min. 0.5 litres) under the
pivoting steam spout (23) and press one of the Steam keys
to start the filter rinsing process.
Ⅲ
Ⅲ
FILTER RINSING
E
Ⅲ Filter rinsing stops automatically.
5. Using a CLARIS plus filter cartridge
Ⅲ
SELECT PRODUCT
When using the CLARIS plus filter cartridge correctly, de-
calcifying your IMPRESSA will no longer be necessary. For
more information on the CLARIS plus filter cartridge refer
to the brochure “CLARIS plus. Hard on limescale. Gentle on
your coffee machine.”
You have now activated the filter. The programming step for
adjusting your machine to the correct water hardness is
therefore no longer displayed.
The water might be slightly discoloured (no hazard to
health).
5.1 Installing the filter
Ⅲ Open the programming door (3). Press the Rotary Switch (4) un-
til you hear an acoustic signal.
5.2 Changing the filter
After 50 litres of water the filter cartridge will need to be
replaced. The display will prompt you to change the filter.
Please monitor the period of use of the CLARIS plus filter
cartridge (max. 2 months) using the scale on the cartridge
holder by the water tank.
Ⅲ
FILTER
NO
Ⅲ Now press the Rotary Switch (4) to start programming.
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ
SELECT PRODUCT / CHANGE FILTER
Ⅲ The Rinse key lights up. Press Rinse
INSERT FILTER / PRESS STEAM
Ⅲ
FILTER
YES
.
Ⅲ
Ⅲ Confirm your setting by pressing the Rotary Switch (4).
Ⅲ Remove the water tank (14) from the IMPRESSA. Empty out
any remaining water. Fold up the cartridge holder (Fig. 1).
Attach the extension piece to the top of the CLARIS plus filter
cartridge. Now insert the filter cartridge in the water tank, apply-
ing gentle pressure (Fig. 1)
Ⅲ
INSERT
FILTER / PRESS STEAM
Ⅲ Take out the water tank (14). Empty out any remaining water.
Fold up the cartridge holder (Fig. 1). Attach the extension piece
(contained in the Welcome Pack) to the top of the CLARIS plus
filter cartridge. Now insert the filter cartridge in the water tank,
applying gentle pressure (Fig. 1)
Ⅲ Close the cartridge holder until it engages audibly.
Ⅲ Fill the water tank (14) with cold, fresh tap water and place it
back into the machine.
Ⅲ Close the cartridge holder until it engages audibly.
9
Ⅲ Place a sufficiently large receptacle (min. 0.5 litres) under the
pivoting steam spout (23) and press one of the Steam keys
to start the filter rinsing process.
Ⅲ
1 ESPRESSO (example)
NORMAL (example)
Ⅲ The coffee brewing process stops automatically as soon as the
Ⅲ
FILTER RINSING
set amount of water has run through.
Ⅲ Filter rinsing stops automatically.
Ⅲ
SELECT PRODUCT
Ⅲ
SELECT PRODUCT
To stop the brewing process prematurely, press any of the
product keys.
You can also trigger a change of filter manually from the
Maintenance menu at any point in time (only if the filter has
been activated) - see Chapter 13.3.
You can change the amount of water while the machine is
brewing coffee. Open the programming door. Turn the
Rotary Switch (4) until the display indicates the required
amount (ML). The amount of water can be selected in incre-
ments of 5 ML.
6. Rinsing the machine
If the coffee machine is switched off and has cooled down,
you will be prompted to start a rinsing cycle when switching
the machine back on. The rinsing cycle starts automatically
when you switch the machine off.
The amounts given in ML are approximate values and may
vary from the effective quantity.
Ⅲ
PRESS RINSE
7.1. Making coffee with pre-ground coffee powder
Ⅲ Place a cup under the coffee spout (18).
Never use water-soluble instant coffee.
Ⅲ Press Rinse
.
Ⅲ
Ⅲ
MACHINE RINSING
SELECT PRODUCT
Ⅲ
SELECT PRODUCT
Ⅲ Place 1 or 2 cups (as required) under the coffee spout (18) and
open the programming door (3). Press the selection key for pre-
You can also trigger a rinsing cycle manually from the Main-
tenance menu at any point in time (see Chapter 13.3).
ground coffee
FILL
POWDER / SELECT PRODUCT
.
Ⅲ
7. Making coffee
(1 espresso, 2 espressos, 1 coffee, 2 coffees)
Ⅲ Now fill 1 or 2 level scoops of pre-ground coffee into the filler
funnel for pre-ground coffee (17).
Ⅲ
SELECT PRODUCT
Ⅲ Place 1 or 2 cups (as required) under the coffee spout (18) and
press a key of your choice . The pre-brewing
process (I.P.B.A.S.) moistens the coffee powder, briefly inter-
rupts the flow of hot water and then begins with the actual brew-
ing process.
Ⅲ Then press a product key of your choice.
,
,
,
Ⅲ
1 ESPRESSO (example)
POWDER
10
Ⅲ The coffee brewing process stops automatically as soon as the
set amount of water has run through.
Ⅲ
A LA CARTE
XSTRONG (example)
Ⅲ
SELECT PRODUCT
Ⅲ The coffee brewing process stops automatically as soon as the
set amount of water has run through.
To stop the brewing process prematurely, press any of the
product keys.
Ⅲ
SELECT PRODUCT
E
To stop the brewing process prematurely, press any of the
product keys.
We recommend always using powder from fresh coffee
beans or pre-ground, vacuum-packed coffee. Never fill in
more than 2 scoops of powder. The filler funnel is no storage
tank. Make sure the coffee powder you use is not too fine.
This may block the system and cause the coffee only to drip
out of the coffee spout.
You can change the amount of water while the machine is
brewing coffee. To do so, turn the Rotary Switch (4) until the
display indicates the required amount (ML). The amount of
water can be selected in increments of 5 ML.
If you have pressed the selection key
press any of the product keys to cancel your selection.
unintentionally,
The amounts given in ML are approximate values and may
vary from the effective quantity.
You can change the amount of water while the machine is
brewing coffee. To do so, turn the Rotary Switch (4) until the
display indicates the required amount (ML). The amount of
water can be selected in increments of 5 ML.
9. Making hot water
Ⅲ
SELECT PRODUCT
Ⅲ Place 1 cup or 1 glass under the hot water spout (25) and turn the
The amounts given in ML are approximate values and may
vary from the effective quantity.
Hot Water switch (22) to
.
Ⅲ
WATER
PORTION
8. Making coffee à la carte
Ⅲ The machine stops dispensing water automatically as soon as the
set amount of water has been dispensed.
Ⅲ
SELECT PRODUCT
Ⅲ
CLOSE TAP
Ⅲ Turn the switch (22) back to
SELECT PRODUCT
Ⅲ Place 1 cup under the coffee spout (18) and open the program-
ming door (3). Press the Coffee à la Carte key
.
.
Ⅲ
A LA CARTE
XMILD
Ⅲ
To stop the process prematurely, turn the switch (22) back
to
Ⅲ Turn the Rotary Switch (4) until the display indicates the desired
coffee strength and press the Rotary Switch (4) to make the cof-
fee. The pre-brewing process (I.P.B.A.S.) moistens the coffee
powder, briefly interrupts the flow of hot water and then begins
with the actual brewing process.
.
11
You can also change the amount of water set while the
machine is brewing coffee. Open the programming door.
Turn the Rotary Switch (4) until the display indicates the
required amount (ML). The amount of water can be selected
in increments of 5 ML.
Ⅲ Press the Steam Portion key
STEAM PORTION
Ⅲ You can stop the process any time by pressing the Steam Portion
key
.
Ⅲ
.
Ⅲ
SELECT PRODUCT
The amounts given in ML are approximate values and may
vary from the effective quantity.
You can set the duration of drawing off steam in 1-second
increments with the Rotary Switch (4).
10. Drawing off steam
11. Frothing milk
Make sure the nozzle has engaged properly. If the nozzle is
clogged with dried milk or has not been attached properly, it
might suddenly come off during operation.
The IMPRESSA is ready to froth milk when both Steam key lights
light up constantly.
If the lights are off, press one of the two Steam keys
.
To ensure perfect operation, clean the 2-stage frothing jet
(24) regularly. Use the opening provided on the handle of the
measuring spoon for the purpose to unscrew the 2-stage
frothing nozzle (Fig. 14). Thoroughly rinse the 3 parts under
running water.
11.1 Frothing one portion of milk
(with the 2-stage frothing jet)
Ⅲ
SELECT PRODUCT
Ⅲ Pour milk into a jug or similar receptacle.
Steam can be used for heating liquids and frothing milk for
cappuccino. When heating liquids, make sure the 2-stage
frothing jet (24) is pushed up. To froth liquids, push the
2-stage frothing jet (Fig. 5) downwards, turning it slightly.
Ⅲ Dip the 2-stage frothing jet (24) into the milk and press the
key.
Ⅲ
STEAM PORTION
Ⅲ The steam dispensing process stops automatically.
A small amount of water leaks from the jet when you start
frothing. This does not affect the result, e.g. when frothing
milk.
There might be some initial splashing when drawing off
steam. The steam jet gets hot. Avoid direct contact with the
skin!
11.2 Frothing milk
(with the 2-stage frothing jet)
Ⅲ
SELECT PRODUCT
Ⅲ Pour milk into a jug or similar receptacle.
Ⅲ
SELECT PRODUCT
Ⅲ Dip the 2-stage frothing jet (24) into the milk and press the
key.
Ⅲ Place a cup under the pivoting steam spout (23) and dip the
2-stage frothing jet (24) in the milk to be frothed or the liquid to
be heated.
12
11.5 Cleaning the Professional-Cappuccino Frother
and jet*
Ⅲ
DRAW OFF STEAM
Ⅲ When you have frothed the milk to your liking, pres the
key
again.
After heating or frothing milk, you should clean the Profes-
sional-Cappuccino Frother. We recommend cleaning it on a
daily basis.
11.3 Attaching the Professional-Cappuccino Frother
to the IMPRESSA*
E
Your IMPRESSA will not prompt you to clean the Profes-
sional-Cappuccino Frother.
Ⅲ Remove the 2-stage frothing jet (24).
Ⅲ Now attach the Professional-Cappuccino Frother (Fig. 6).
The Professional-Cappuccino Frother and the Easy-Cappuc-
cino Frother are best cleaned using the JURA Auto-Cappuc-
cino cleaner. Please contact an authorized dealer. We recom-
mend cleaning these devices daily.
Ⅲ Press the hose into one side of the opening behind the dial
(Fig. 7).
IMPRESSA S9 avantgarde: The supplied “Deluxe” milk
pitcher is suited for drawing in the milk.
Ⅲ Fill water into a receptacle and dip the milk hose into it.
Ⅲ Draw steam until the water / steam from the Frother runs clear.
11.4 Making cappuccino and hot milk with the
Professional-Cappuccino Frother*
We also recommend regularly disassembling the Frother and
rinsing it under running water.
Ⅲ Fill the milk pitcher with milk or dip the milk hose directly into
the milk.
Ⅲ Remove the Professional-Cappuccino Frother from the IMPRES-
SA and take it apart as shown in Fig. 8.
Ⅲ Place a cup under the Professional-Cappuccino Frother.
Ⅲ Press the Steam Portion key
STEAM PORTION
.
Ⅲ Thoroughly rinse all the parts of the Professional-Cappuccino
Frother under running water.
Ⅲ
Ⅲ The machine will froth or heat milk according to the time you
programmed (see “Programming the steam portion”, Chapter
13.8)
Ⅲ Re-assemble the Professional-Cappuccino Frother and attach it
to your IMPRESSA.
Ⅲ For cappuccino, turn the selector switch (1, Fig. 7) to (2).
12. Switching the IMPRESSA S9/S7 avantgarde off
Ⅲ For hot milk, turn the selector switch (1, Fig. 7) to (3).
Switching the IMPRESSA off causes the coffee spout to be rinsed
first. Therefore, please make sure to place a suitable receptacle
under the coffee spout (18).
Ⅲ Now place the cup with the cappuccino froth or hot milk under
the coffee spout (18) and make a coffee of your choice.
Ⅲ
SELECT PRODUCT
Ⅲ Switch the IMPRESSA off with the ON / OFF key
(11).
13
*The Professional-Cappuccino Frother is optional with the IMPRESSA S7 avantgarde.
13.3 Maintenance
Ⅲ
MACHINE RINSING
Ⅲ The coffee spout (18) is rinsed.
You can activate the following maintenance functions from this
program item:
13. Programming
RINSE MACHINE, CLEAN MACHINE, DE-SCALE MACHINE,
CHANGE FILTER.
The IMPRESSA leaves the factory with a number of default
settings that allow you to make coffee without having to pro-
gram the machine first. You can, however, adjust various
parameters to make the coffee suit your personal taste.
“DE-SCALE machine” is not displayed if you are using a CLARIS
plus filter cartridge and the filter is set to “YES”.
“CHANGE FILTER” is not displayed if you are not using a
CLARIS plus filter cartridge and the filter is set to “NO”.
The following parameters can be adjusted:
Ⅲ
SELECT PRODUCT
ț Filter
ț Water hardness
ț Rinse
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
ț Powder quantity
ț Water quantity
ț Temperature
ț Water portion
ț Steam portion
ț Economy mode
ț Time
Ⅲ
FILTER
NO or YES
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ
RINSE
Ⅲ Now press the Rotary Switch (4) to start programming.
ț Automatic switch-on time
ț Automatic switch-off time
ț Language
Ⅲ
RINSE
MACHINE
Ⅲ Turn the Rotary Switch (4) until the required maintenance func-
tion (for selection see above) is displayed. Press the Rotary
Switch (4) to activate the function.
ț Display
ț Information (to be viewed only)
13.1 Programming the filter
The Maintenance menu closes automatically after 5 seconds
if no function is selected.
Please refer to Chapter 5 “Using the CLARIS plus filter cartridge”.
13.4 Programming the amount of powder for coffee
and espresso
13.2 Programming your machine to the correct
water hardness (only with FILTER NO)
You can adjust the amount of powder for coffee and espresso
separately.
Please refer to Chapter 4 “Adjusting your machine to the water
hardness”.
14
13.5 Setting the amount of water for coffee,
espresso and coffee à la carte
Ⅲ
SELECT PRODUCT
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
The system’s basic settings include pre-defined amounts of water
(coffee 130 ml, espresso 60 ml, 2 coffees 260 ml, coffee à la carte
145 ml). However, these can be modified as required.
Ⅲ
FILTER
NO or YES
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
E
Ⅲ
SELECT PRODUCT
Ⅲ Open the programming door (3). Press the Rotary Switch (4) un-
Ⅲ
POWDER
til you hear an acoustic signal.
QUANTITY
Ⅲ
FILTER
NO or YES
Ⅲ Now press the Rotary Switch (4) to start programming.
Ⅲ
SELECT
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
PRODUCT
played:
Ⅲ Then press a product key of your choice.
NORMAL (example)
ⅥⅥⅥ _ _ _ +
Ⅲ
WATER
QUANTITY
Ⅲ
–
Ⅲ Press the Rotary Switch (4) to activate the program item.
Ⅲ Now turn the Rotary Switch (4) until the required amount of
powder is set.
Ⅲ
SELECT
PRODUCT
Ⅲ
STRONG (example)
ⅥⅥⅥⅥ _ _ +
Ⅲ Confirm the selected setting by pressing the Rotary Switch (4).
Ⅲ Press a product key of your choice.
–
Ⅲ
1 ESPRESSO (example)
60 ML
Ⅲ
POWDER
Ⅲ Turn the Rotary Switch (4) to adjust the amount of water and
QUANTITY
then confirm your setting by pressing the Rotary Switch (4).
Ⅲ Now turn the Rotary Switch (4) until the following message is
displayed:
Ⅲ
WATER
QUANTITY
Ⅲ
EXIT
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
Ⅲ Now press the Rotary Switch (4) to leave the programming
mode.
played:
Ⅲ
EXIT
Ⅲ Press the Rotary Switch (4) to leave the programming mode.
SELECT PRODUCT
Ⅲ
SELECT PRODUCT
Ⅲ
15
13.6 Programming the temperature for coffee,
espresso and coffee à la carte
13.7 Programming the water portion
The system’s basic settings include a pre-defined amount of water
(225 ml). However, this amount can be modified as required.
You can adjust the temperature for each type of coffee sepa-
rately. The temperature can be set to 2 different levels
(NORMAL, HIGH).
Ⅲ
SELECT PRODUCT
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
Ⅲ
SELECT PRODUCT
Ⅲ
FILTER
NO or YES
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ
FILTER
NO or YES
Ⅲ
WATER
PORTION
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ Press the Rotary Switch (4) to activate the program item.
Ⅲ
TEMP
Ⅲ Now press the Rotary Switch (4) to start programming.
SELECT PRODUCT
Ⅲ Then press a product key of your choice.
Ⅲ
PORTION
225 ML (example)
Ⅲ
Ⅲ Turn the Rotary Switch (4) to adjust the amount of water and
then confirm your setting by pressing the Rotary Switch (4).
Ⅲ
TEMP
NORMAL (example)
Ⅲ
WATER
PORTION
Ⅲ Now turn the Rotary Switch (4) until the required temperature is
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
set.
Ⅲ
TEMP
HIGH (example)
Ⅲ
EXIT
Ⅲ Press the Rotary Switch (4) to leave the programming mode.
SELECT PRODUCT
Ⅲ Confirm the selected setting by pressing the Rotary Switch (4).
TEMP
Ⅲ
Ⅲ
Ⅲ Now turn the Rotary Switch (4) until the following message is
displayed:
13.8 Programming the steam portion
The system’s basic settings include a pre-defined steam portion (20
sec.). However, this amount can be modified as required.
Ⅲ
EXIT
Ⅲ Now press the Rotary Switch (4) to leave the programming
Ⅲ
SELECT PRODUCT
mode.
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
Ⅲ
SELECT PRODUCT
16
Ⅲ Now press the Rotary Switch (4) to start programming.
Ⅲ
FILTER
NO or YES
Ⅲ
ECONOMY
MODE -
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ Now turn the Rotary Switch (4) until the required economy
mode is displayed.
Ⅲ
STEAM
PORTION
Ⅲ
ECONOMY
MODE 2 (example)
E
Ⅲ Press the Rotary Switch (4) to activate the program item.
Ⅲ Confirm the selected setting by pressing the Rotary Switch (4).
Ⅲ
PORTION
20 SEC (example)
Ⅲ
ECONOMY
MODE 2 (example)
Ⅲ Turn the Rotary Switch (4) to modify the steam portion and then
confirm your setting by pressing the Rotary Switch (4).
Ⅲ Now turn the Rotary Switch (4) until the following message is
displayed:
Ⅲ
STEAM
PORTION
Ⅲ
EXIT
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ Now press the Rotary Switch (4) to leave the programming
mode.
Ⅲ
EXIT
Ⅲ Press the Rotary Switch (4) to leave the programming mode.
SELECT PRODUCT
Ⅲ
SELECT PRODUCT
Ⅲ
Economy mode –
Selecting this level puts the IMPRESSA in constant stand-by
mode.
This setting allows you to make any of the products without having
to wait for the machine to heat up.
13.9 Economy mode
You can set your machine to various power saving modes.
Select this setting if you want to make a lot of coffees with
hot or frothed milk and do not want to wait for the machine
to heat up first.
Ⅲ
SELECT PRODUCT
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
Ⅲ
FILTER
NO or YES
Economy mode 1
Selecting this level puts the IMPRESSA in constant stand-by mode
for making coffee. The machine is heated up separately if you need
steam for hot or frothed milk.
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ
ECONOMY
MODE –
17
Select this setting if you make mostly black coffees and are
prepared to wait for approx. 1 minute before being able to
draw steam.
Ⅲ
TIME
13:00 (example)
Ⅲ Press the Rotary Switch (4) to confirm the hours and to activate
the minutes.
Economy mode 2
Ⅲ
TIME
13:00
Selecting this level does not put the IMPRESSA in stand-by mode
(economy temperature). The machine heats up each time you make
coffee or need to draw steam.
The IMPRESSA switches to economy temperature 5 minutes after
you last used it.
Ⅲ Turn the Rotary Switch (4) to set the minutes.
Ⅲ
TIME
13:50 (example)
Ⅲ Press the Rotary Switch (4) to confirm the minutes.
Ⅲ
TIME
13:50
Select this setting if you make very few coffees (with or
without milk) and are prepared to wait for approx. 30 sec-
onds for the machine to get ready.
Ⅲ Now turn the Rotary Switch (4) until the following message is
displayed:
Ⅲ
EXIT
13.10 Setting the time
Ⅲ Now press the Rotary Switch (4) to leave the programming
mode.
You must program the time if you want to use the automatic
switch-on function.
Ⅲ
SELECT PRODUCT
Ⅲ
SELECT PRODUCT
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
13.11 Programming the automatic switch-on time
You must program the time if you want to use the automatic
switch-on function.
Ⅲ
FILTER
NO or YES
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ
SELECT PRODUCT
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
Ⅲ
TIME
—:—
until you hear an acoustic signal.
Ⅲ
FILTER
NO or YES
Ⅲ Now press the Rotary Switch (4) to start programming.
Ⅲ
TIME
—:—
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ Turn the Rotary Switch (4) to set the hours.
Ⅲ
UNIT ON
—:—
18
Ⅲ Now press the Rotary Switch (4) to start programming.
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ
UNIT ON
—:—
Ⅲ
OFF AFTER
5 HRS
Ⅲ Turn the Rotary Switch (4) to set the hours.
Ⅲ Now press the Rotary Switch (4) to start programming.
Ⅲ
UNIT ON
07:00 (example)
Ⅲ
OFF AFTER
5 HRS
E
Ⅲ Press the Rotary Switch (4) to confirm the hours and to activate
the minutes.
Ⅲ Turn the Rotary Switch (4) to set the switch-off time.
Ⅲ
UNIT ON
07:00
Ⅲ
OFF AFTER
4 HRS (example)
Ⅲ Turn the Rotary Switch (4) to set the minutes.
Ⅲ Confirm the set switch-off time by pressing the Rotary Switch
(4).
Ⅲ
UNIT ON
07:15 (example)
Ⅲ
OFF AFTER
4 HRS
Ⅲ Press the Rotary Switch (4) to confirm the minutes.
Ⅲ Now turn the Rotary Switch (4) until the following message is
displayed:
Ⅲ
UNIT ON
07:15
Ⅲ
EXIT
Ⅲ Now press the Rotary Switch (4) to leave the programming mode.
Ⅲ SELECT PRODUCT
Ⅲ Now turn the Rotary Switch (4) until the following message is
displayed:
Ⅲ
EXIT
Ⅲ Now press the Rotary Switch (4) to leave the programming mode.
13.13 Programming the language
Ⅲ
SELECT PRODUCT
Ⅲ
SELECT PRODUCT
If the IMPRESSA is switched off with the power switch
(27), you will need to set the time again next time you switch
the machine on. The machine will prompt you to do so.
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
Ⅲ
FILTER
NO or YES
13.12 Programming the automatic switch-off time
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
Ⅲ
SELECT PRODUCT
played:
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
Ⅲ
SPRACHE
DEUTSCH
Ⅲ
FILTER
NO or YES
Ⅲ Now press the Rotary Switch (4) to start programming.
19
Ⅲ Turn the Rotary Switch (4) to change the time format.
Ⅲ
SPRACHE
DEUTSCH
Ⅲ
DISPLAY
AM / PM / ML
Ⅲ Turn the Rotary Switch (4) to set the language.
Ⅲ Confirm your selection by pressing the Rotary Switch (4).
Ⅲ
LANGUAGE
ENGLISH (example)
Ⅲ
DISPLAY
AM / PM / ML
Ⅲ Confirm your selection by pressing the Rotary Switch (4).
Ⅲ Turn the Rotary Switch (4) to change the unit of measurement.
Ⅲ
LANGUAGE
ENGLISH
Ⅲ
DISPLAY
AM / PM / OZ
Ⅲ Now turn the Rotary Switch (4) until the following message is
displayed:
Ⅲ Confirm your selection by pressing the Rotary Switch (4).
Ⅲ
EXIT
Ⅲ Now press the Rotary Switch (4) to leave the programming mode.
SELECT PRODUCT
Ⅲ
DISPLAY
AM / PM / OZ
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
Ⅲ
played:
Ⅲ
EXIT
13.14 Programming the display
Ⅲ Now press the Rotary Switch (4) to leave the programming
This program item allows you to change the time format
from 24 hrs. to AM/PM and the units from ml (millilitres) to
oz (ounces).
mode.
Ⅲ
SELECT PRODUCT
Ⅲ
SELECT PRODUCT
13.15 Information
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
This program item enables you to check the number of
products you made and how often you selected a specific
function.
until you hear an acoustic signal.
Ⅲ
FILTER
NO or YES
Ⅲ
SELECT PRODUCT
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ Open the programming door (3). Press the Rotary Switch (4)
until you hear an acoustic signal.
Ⅲ
DISPLAY
24HRS / ML
Ⅲ
FILTER
NO or YES
Ⅲ Now press the Rotary Switch (4) to start programming.
Ⅲ Turn the Rotary Switch (4) until the following message is dis-
played:
Ⅲ
DISPLAY
24HRS / ML
Ⅲ
INFO
20
Ⅲ Now press the Rotary Switch (4) to access the Information
menu.
14. Maintenance
14.1 Filling the water tank
Ⅲ
TOTAL
1000 (example)
Ⅲ
FILL
WATER TANK
Ⅲ Turn the Rotary Switch (4) to display how often you made 2
espressos, 1 coffee, 2 coffees, coffee à la carte, powder, water
and steam.
If this information is displayed, the machine will no longer
make coffee. Refill water as described in Chapter 2.3.
E
Ⅲ Finally, the number of cleaning and decalcifying cycles and filter
changes are displayed.
Ⅲ
SELECT PRODUCT
Ⅲ To exit the information program, press the Rotary Switch (4).
Ⅲ
INFO
The water tank should be rinsed out and filled with fresh
water daily. Always use fresh, cold water. Never fill the
water tank with milk, mineral water or other liquids.
Ⅲ Now turn the Rotary Switch (4) until the following message is
displayed:
Ⅲ
EXIT
14.2 Emptying the coffee grounds
Ⅲ Now press the Rotary Switch (4) to leave the programming
mode.
Ⅲ
EMPTY
GROUNDS
Ⅲ
SELECT PRODUCT
If this information is displayed, the machine will no longer
make coffee. However, the machine will still dispense hot
water and steam. Empty the coffee grounds bin (26).
13.16 Resetting products to factory settings
Ⅲ Possibilities are provided to enable you to reset Espresso and
coffee products to the factory settings.
Ⅲ Carefully take out the drip tray (1) - which contains water - and
the integrated coffee grounds bin.
Ⅲ With draw-off buttons 1 Espresso and 1 Coffee, the following
parameters can be reset: coffee strength, amount of water, tem-
perature.
Ⅲ
TRAY
MISSING
Ⅲ With draw-off buttons 2 Espressi and 2 Coffees, the following
Ⅲ Place the empty, clean drip tray (1) and integrated coffee
grounds bin back into the IMPRESSA. (The tray must be re-
moved from the machine for at least 10 seconds).
parameters can be reset: amount of water, temperature.
Ⅲ To reset the buttons, with your IMPRESSA in Standby mode and
with the power switched ON, press the rotary switch and the
draw-off button that you wish to reset simultaneously and hold
them down until the display shows
Ⅲ
SELECT PRODUCT
1 ESPRESSO (example)
OK
21
14.3 Emptying the drip tray
14.6 Removing stones from the grinding gear
Ⅲ
EMPTY
TRAY
Ⅲ Switch the machine off using the ON / OFF key
(11).
Ⅲ Turn the power switch (27) off.
Ⅲ Open the lid of the bean tank (16) and remove the aroma preser-
vation cover (15).
If this information is displayed, the machine will no longer
dispense coffee or steam, and the tray must be emptied.
Ⅲ Remove any beans with a vacuum cleaner.
Ⅲ Carefully take out the drip tray (1) – which contains water – and
the integrated coffee grounds bin.
Ⅲ Remove the screw in the bean tank (Fig. 9) and fold the finger
protection device up (Fig. 10).
Ⅲ
TRAY
Ⅲ Insert the key (Fig. 11).
MISSING
Ⅲ Now turn the key counter-clockwise until the jammed stone is
released.
Ⅲ Place the empty, clean drip tray (1) and integrated coffee
grounds bin back into the IMPRESSA.
Ⅲ Remove any remaining powder with a vacuum cleaner.
Ⅲ
SELECT PRODUCT
Ⅲ Fold the finger protection device (Fig. 10) down and screw it
tight.
14.4 Drip tray missing
Ⅲ Fill the bean tank with fresh beans.
Ⅲ
TRAY
MISSING
14.7 Changing the filter
If this information is displayed, the machine will no longer
make coffee. The drip tray (1) and integrated coffee grounds
bin have not been installed or not been installed properly.
After 50 litres of water the filter cartridge will need to be
replaced. The display will prompt you to change the filter.
Refer to Chapter 5.2 “Changing the filter”.
Ⅲ Insert the drip tray (1) and integrated coffee grounds bin.
SELECT PRODUCT
Ⅲ
14.8 Prompt to run cleaning cycle
After having dispensed 220 products or after 80 rinsing cycles, the
IMPRESSA must be cleaned. You will be informed of this by a
message on the display. The machine will still make coffee, hot
water and steam. However, we recommend that you should run the
cleaning cycle (see Chapter 15) within the next few days.
14.5 Filling the bean tank
Ⅲ
FILL
BEANS
If this information is displayed, the machine will no longer
make coffee. However, the machine will still dispense hot
water and steam. Refill beans as described in Chapter 2.4.
Ⅲ
SELECT PRODUCT /
CLEAN MACHINE
Ⅲ
SELECT PRODUCT
22
After another 30 products the display will change. You should run
the cleaning cycle now (see Chapter 15).
Ⅲ When the process has been completed, the IMPRESSA switches
itself off.
Ⅲ
SELECT PRODUCT /
CLEAN NOW
The display will read “FILL SYSTEM / PRESS STEAM” next
time you switch the machine on. For more information, please refer
to Chapter 3 “First use”.
14.9 Prompt to decalcify
E
14.11 General cleaning instructions
Lime scale builds up in the IMPRESSA as a result of normal use.
The degree of calcification depends on the hardness of the water
you use. The IMPRESSA recognizes when you should run a decal-
cifying cycle. The machine will still make coffee, hot water and
steam. However, we recommend that you should decalcify the ma-
chine (see Chapter 16) within the next few days.
Ⅲ Never use sharp objects or caustic chemicals for cleaning.
Ⅲ Clean the case using a soft, damp cloth.
Ⅲ Clean the pivoting steam spout (23) after each use.
Ⅲ After heating milk, draw off some hot water to clean the inside
of the pivoting steam spout (23).
Ⅲ
SELECT PRODUCT /
DE-SCALE MACHINE
Ⅲ Remove the Professional-Cappuccino Frother to clean it
thoroughly.
Ⅲ The water tank should be rinsed out and filled with fresh water
daily.
After a while the display will change. You should run the decalci-
fying cycle now (see Chapter 16).
Visible calcification in the water tank can be removed using
a commercial decalcifying agent. To do so, remove the water
tank from the machine.
Ⅲ
SELECT PRODUCT /
DE-SCALE NOW
If you are using a CLARIS plus filter cartridge, remove it
from the tank first.
14.10 Emptying the system
Requirements: The IMPRESSA has been switched off with the
ON / OFF key
(11), but the power switch (27) is still turned on.
15. Cleaning
This is necessary to protect the machine against damage
occurring during transport as a result of frost.
The IMPRESSA features an integrated cleaning program. The
process takes approx.15 minutes.
Ⅲ Place a receptacle under the pivoting steam spout (23).
Please only use original JURA cleaning tablets: their formula
is especially tailored to JURA coffee machines. Please note
that the use of unsuitable cleaning agents may cause damage
to your machine and could leave unfavourable residues in the
water.
Ⅲ Press one of the Steam keys
until the following message is
displayed:
Ⅲ
SYSTEM
EMPTYING
23
Once started, the cleaning process must not be interrupted.
Ⅲ
EMPTY TRAY /
EMPTY GROUNDS
Ⅲ Empty out the drip tray (1) and integrated coffee grounds bin.
After each cleaning process, the filler funnel for the pre-
ground coffee (17) should be cleaned as well.
Ⅲ
TRAY
MISSING
Ⅲ
SELECT PRODUCT
CLEAN MACHINE
Ⅲ Place the empty, clean drip tray (1) and integrated coffee
grounds bin back into the IMPRESSA.
Ⅲ Press Rinse
until the following message appears:
EMPTY TRAY /
EMPTY GROUNDS
Ⅲ Empty out the drip tray (1) and integrated coffee grounds bin.
Ⅲ
SELECT PRODUCT
Ⅲ
Ⅲ When the cleaning program has finished, take out the removable
coffee powder tank and briefly rinse it under running water.
You can also trigger a cleaning cycle manually at any point
in time (see Chapter 13.3).
Ⅲ
TRAY
MISSING
Ⅲ Place the empty, clean drip tray (1) and integrated coffee
grounds bin back into the IMPRESSA.
16. Decalcifying
The IMPRESSA features an integrated decalcifying program. The
process takes approx.50 minutes.
Ⅲ
PRESS
RINSE
Ⅲ Place a sufficiently large receptacle (ca. 0.5 litres) under the
coffee spout (18).
Lime scale builds up in the IMPRESSA as a result of normal
use. The degree of calcification depends on the hardness of
the water you use. The IMPRESSA recognizes when you
should run a decalcifying cycle. The machine will still make
coffee and hot water/steam. However, we recommend that
you should decalcify the machine within a few days after the
message was displayed.
Ⅲ Press Rinse
.
Ⅲ
MACHINE
CLEANING
Ⅲ You will hear an acoustic signal.
Ⅲ
ADD
TABLET / PRESS RINSE
Please only use original JURA de-scaling tablets: their for-
mula is especially tailored to JURA coffee machines. Please
note that the use of unsuitable decalcifying agents may cause
damage to your machine and could leave unfavourable
residues in the water.
Ⅲ Open the lid of the filler funnel for pre-ground coffee (17). Drop
an original JURA cleaning tablet inside (Fig. 12) and close the
lid.
Ⅲ Press Rinse
.
Ⅲ
MACHINE
CLEANING
Remove any splashes or drops of the decalcifying agent from
sensitive surfaces, in particular surfaces made of natural
stone or wood, or take appropriate preventive measures.
Ⅲ You will hear an acoustic signal.
24
Once started, the decalcifying program must not be inter-
rupted.
Ⅲ Turn the Hot Water key (22) to the symbol.
Ⅲ
MACHINE
DE-SCALING
Always wait until the decalcifying agent has been used up
and the tank is empty. Never fill in additional decalcifying
agent.
Ⅲ You will hear an acoustic signal.
CLOSE TAP
Ⅲ Turn the Hot Water key (22) to the
Ⅲ
symbol.
E
Ⅲ
SELECT PRODUCT
DE-SCALE MACHINE
Ⅲ
MACHINE
DE-SCALING
Ⅲ Press Rinse
until the following message appears:
EMPTY TRAY /
EMPTY GROUNDS
Ⅲ Empty out the drip tray (1) and integrated coffee grounds bin.
Ⅲ You will hear an acoustic signal.
Ⅲ
Ⅲ
EMPTY TRAY /
EMPTY GROUNDS
Ⅲ Empty out the drip tray (1) and integrated coffee grounds bin.
Ⅲ
TRAY
MISSING
Ⅲ
TRAY
MISSING
Ⅲ Place the empty, clean drip tray (1) and integrated coffee
grounds bin back into the IMPRESSA.
Ⅲ Place the empty, clean drip tray (1) and integrated coffee
grounds bin back into the IMPRESSA.
Ⅲ
AGENT IN TANK /
PRESS STEAM
Ⅲ
RINSE WATER TANK /
FILL WATER TANK
Ⅲ Take out the water tank (14). Empty out any remaining water.
Thoroughly rinse out the water tank and fill it with fresh cold
tap water. Then place it back into the IMPRESSA.
Completely dissolve the content of one blister (3 tablets) in a
receptacle containing 0.6 litres of water, and pour the mixture into
the water tank. Place the water tank back into the machine.
Ⅲ
PRESS STEAM
Ⅲ Place a receptacle under the pivoting steam spout (23).
Ⅲ Press one of the Steam keys
Ⅲ Remove the 2-stage frothing jet (24) or Professional-Cappuccino
Frother from the machine (if attached).
.
Ⅲ
MACHINE
Ⅲ Place a tall receptacle under the pivoting steam spout (23) and
DE-SCALING
press one of the Steam keys
.
Ⅲ You will hear an acoustic signal.
OPEN TAP
Ⅲ
MACHINE
DE-SCALING
Ⅲ
Ⅲ You will hear an acoustic signal.
OPEN TAP
Ⅲ Place the receptacle under the hot water spout (25).
Ⅲ Place the receptacle under the hot water spout (25).
Ⅲ
Ⅲ Turn the Hot Water key (22) to the symbol.
25
18. Tips for perfect coffee
Ⅲ
MACHINE
DE-SCALING
Height-adjustable coffee spout (18)
You can adjust the height of the coffee spout to the size of your
cups.
Ⅲ You will hear an acoustic signal.
CLOSE TAP
Ⅲ Turn the Hot Water key (22) to the
Ⅲ
symbol.
Grinding degree
Refer to Chapter 2.5 “Adjusting the grinding gear”.
Ⅲ
MACHINE
DE-SCALING
Ⅲ You will hear an acoustic signal.
Preheating cups
The machine features a passively heated cup tray (19). You can,
however, additionally preheat the cups with hot water. The smaller
the quantity of coffee you make, the more important preheating is.
Ⅲ
EMPTY TRAY /
EMPTY GROUNDS
Ⅲ Empty out the drip tray (1) and integrated coffee grounds bin.
Ⅲ
TRAY
MISSING
Sugar and cream
Stirring causes heat to be released. Adding refrigerated cream or
milk will reduce the temperature of the coffee significantly.
Ⅲ Place the empty, clean drip tray (1) and integrated coffee
grounds bin back into the IMPRESSA.
Ⅲ
SELECT PRODUCT
You can also trigger a decalcifying cycle manually at any
point in time (see Chapter 13.3).
17. Disposal
Please return the IMPRESSA to your local dealer, the service shop
or to JURA for proper disposal.
26
19. Problems
Problem
Cause
Remedy
Grinding gear makes a very loud noise
Too little froth when frothing milk
Coffee only drips from the coffee spout
Foreign body in the grinding gear
Professional Cappuccino Frother clogged
Grinding degree too fine
Pre-ground coffee too fine
Please refer to Chapter 14.6
Clean frother (Chapter 11.5)
Adjust grinding gear to coarser grind
Use a coarser type of pre-ground coffee
Clean metal contacts
E
Display constantly indicates ‘Tray missing‘
Soiled metal contacts at rear of drip
tray (Fig. 13)
‘Fill beans’ not displayed despite empty
bean tank
Bean monitoring system soiled
Clean bean tank (dry)
27
20. Legal information
21. Technical data
Voltage:
These operating instructions contain all the information required
for operating and maintaining the machine properly.
Knowledge of and compliance with the specifications contained in
these operating instructions is required for using the machine
safely as well as for operational safety and safety during mainte-
nance.
230 V AC
1350 W
10 A
Power:
Fuse:
Safety check:
These operating instructions cannot cover all conceivable appli-
cations. The machine was designed for private household use.
Additionally, we point out that the contents of these operating
instructions do not modify or form part of any previous or existing
agreement, consent or legal relationship. Any obligations to be
fulfilled by JURA Elektroapparate AG are stipulated in the corre-
sponding purchase contract which also contains the full and solely
applicable warranty terms. These contractual warranty terms are
neither extended nor limited by the specifications contained in
these operating instructions.
Economy Mode – power consumption: 40 Wh
Economy Mode 1 power consumption: 20 Wh
Economy Mode 2 power consumption: 15 Wh
Pump pressure:
static max. 15 bar
Water tank:
2.7 litres
Bean tank capacity:
Coffee grounds bin capacity:
Length of cable:
Weight:
280 g
The operating instructions contain information that is protected by
Copyright. Photocopying or translations into other languages shall
not be permissible without JURA Elektroapparate AG’s written
approval.
max. 16 portions
approx. 1.1 m
11.9 kg
Dimensions (WxHxD):
34.5 x 35 x 39 cm
This appliance complies with the following EC directives:
73/23/EEC of February 19th, 1973, “Low Voltage Directive” and
amending directive 93/336/EEC.
89/336/EEC of May 3rd,1989, “EMC Directive” and amending
directive 92/31/EEC.
28
|