Torino S2300
user guide
Your wireless phone is a radio transmitter and receiver. It is
designed and manufactured to not exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government. These
limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. The
guidelines are based on standards that were developed by
independent scientific organizations through periodic and
thorough evaluation of scientific studies. The standards include
a substantial safety margin designed to assure the safety of all
persons, regardless of age and health.
The FCC has granted an Equipment Authorization for this model
phone with all reported SAR levels evaluated as in compliance
with the FCC RF emission guidelines. SAR information on this
model phone is on file with the FCC and can be found under the
the FCC ID: OVF-K5302.
Additional information on SAR can be found on the Cellular
Telecommunications and Internet Association (CTIA) web-site at
.
* In the United States and Canada, the SAR limit for mobile
phones used by the public is 1.6 watts/kg (W/kg) averaged over
one gram of tissue. The standard incorporates a substantial
margin of safety to give additional protection for the public and to
account for any variations in measurements.
The exposure standard for wireless mobile phones employs a
unit of measurement known as the Specific Absorption Rate, or
SAR. The SAR limit set by the FCC is 1.6 W/kg.*
Tests for SAR are conducted using standard operating positions
specified by the FCC with the phone transmitting at its highest
certified power level in all tested frequency bands.
Bluetooth® Certification
For information about S2300 Bluetooth Certification, visit the
Bluetooth Qualification Program Web site at
Although the SAR is determined at the highest certified power
level, the actual SAR level of the phone while operating can be
well below the maximum value. This is because the phone is
designed to operate at multiple power levels so as to use only
the power required to reach the network. In general, the closer
you are to a wireless base station antenna, the lower the power
output.
.
Caution
The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance
could void the warranty and user’s authority to operate the
equipment.
Before a phone model is available for sale to the public, it must
be tested and certified by the FCC that it does not exceed the
limit established by the government-adopted requirement for
safe exposure. The tests are performed in positions and
locations (e.g., at the ear and worn on the body) as required by
the FCC for each model.
Optimize your Phone’s Performance
Use the instructions in this guide to learn how to optimize the
performance and life of your phone and battery.
Air Bags
If you have an air bag, DO NOT place installed or portable
phone equipment or other objects over the air bag or in the air
bag deployment area. If equipment is not properly installed, you
and your passengers risk serious injury.
Body-worn measurements differ among phone models,
depending upon availability of accessories and FCC
requirements. While there may be differences between the SAR
levels of various phones and at various positions, they all meet
the government requirement for safe exposure.
User Guide
3
Vehicles—RF signals may affect improperly installed or
inadequately shielded electronic systems in motor vehicles.
Check with the manufacturer of the device to determine if it is
adequately shielded from external RF energy.
Medical devices
Pacemakers—Warning to pacemaker wearers: Wireless
phones, when in the ‘on’ position, have been shown to interfere
with pacemakers. The phone should be kept at least six (6)
inches away from the pacemaker to reduce risk.
Blasting areas—Turn off your phone where blasting is in
progress. Observe restrictions, and follow any regulations or
rules.
The Health Industry Manufacturers Association and the wireless
technology research community recommend that you follow
these guidelines to minimize the potential for interference.
Potentially explosive atmospheres—Turn off your phone
when you are in any area with a potentially explosive
atmosphere. Obey all signs and instructions. Sparks in such
areas could cause an explosion or fire, resulting in bodily injury
or death. Areas with a potentially explosive atmosphere are
often, but not always, clearly marked.
•
Always keep the phone at least six inches (15 centimeters)
away from your pacemaker when the phone is turned on.
•
•
•
Do not carry your phone near your heart.
Use the ear opposite the pacemaker.
If you have any reason to suspect that interference is taking
place, turn off your phone immediately.
They include:
•
•
•
•
fueling areas such as gas stations
below deck on boats
Hearing aids—Some digital wireless phones may interfere with
hearing aids. In the event of such interference, you may want to
call the customer service line to discuss alternatives.
transfer or storage facilities for fuel or chemicals
vehicles using liquefied petroleum gas, such as propane or
butane
Other medical devices—If you use any other personal medical
device, consult the manufacturer of the device to determine if it
is adequately shielded from external RF energy. Your physician
may be able to help you obtain this information.
•
•
areas where the air contains chemicals or particles such as
grain, dust, or metal powders
any other area where you would normally be advised to turn
off your vehicle engine
In health care facilities—Turn your phone off in health care
facilities when instructed. Hospitals and health care facilities
may be using equipment that is sensitive to external RF energy.
Use with care
Potentially unsafe areas
Posted facilities—Turn your phone off in any facility when
Use only in normal position (to ear). Avoid dropping, hitting,
bending, or sitting on the phone.
posted notices require you to do so.
Avoid magnetic environments
Aircraft—FCC regulations prohibit using your phone on a plane
that is in the air. Turn your phone off or switch it to Airplane
Mode before boarding aircraft.
Keep the phone away from magnets which can cause improper
functioning of the phone.
Keep your phone dry
Keep the phone dry. Damage can result if the phone gets wet.
Water damage is not covered under warranty.
4
Resetting the phone
If the screen seems frozen and the keypad does not respond to
keypresses, reset the phone by completing the following steps:
Hearing Aid Compatibility (HAC) with Mobile
Phones
Some mobile phones and hearing devices (hearing aids and
cochlear implants), when used together, result in buzzing,
humming, or whining noises detected by the user.
1. Remove the battery cover.
2. Remove and replace the battery.
Some hearing devices are more immune than others to this
interference noise, and phones also vary in the amount of
interference they generate.
If the problem persists, return the phone to the dealer for
service.
Accessories
The wireless telephone industry has developed ratings for some
of their mobile phones, to assist hearing device users in finding
phones that may be compatible with their hearing devices. Not
all phones have been rated.
Use only Kyocera-approved accessories with Kyocera phones.
Use of any unauthorized accessories may be dangerous and will
void the phone warranty if said accessories cause damage or a
defect to the phone.
Phones that are rated have the rating on their box or a label on
the box. The ratings are not guarantees and results will vary
depending on the user’s hearing device and hearing loss. If your
hearing device happens to be vulnerable to interference, you
may not be able to use a rated phone successfully. Trying out
the phone with your hearing device is the best way to evaluate it
for your personal needs.
Radio Frequency (RF) energy
Your telephone is a radio transmitter and receiver. When it is on,
it receives and sends out RF energy. Your service provider’s
network controls the power of the RF signal. This power level
can range from 0.006 to 0.6 watts.
In August 1996, the U.S. Federal Communications Commission
(FCC) adopted RF exposure guidelines with safety levels for
hand-held wireless phones. These guidelines are consistent with
the safety standards previously set by both U.S. and
M-Ratings—Phones rated M3 or M4 meet FCC requirements
and are likely to generate less interference to hearing devices
than phones that are not labeled. M4 is the better/higher of the
two ratings.
international standards bodies in the following reports:
T-Ratings—Phones rated T3 or T4 meet FCC requirements and
are likely to be more usable with a hearing device’s telecoil (“T
Switch” or “Telephone Switch”) than unrated phones. T4 is the
better/higher of the two ratings. (Note that not all hearing
devices have telecoils in them.)
•
•
ANSI C95.1 (American National Standards Institute, 1992)
NCRP Report 86 (National Council on Radiation Protection
and Measurements, 1986)
•
ICNIRP (International Commission on Non-Ionizing
Radiation Protection, 1996)
Hearing devices may also be measured for immunity to this type
of interference. Your hearing device manufacturer or hearing
health professional may help you choose the proper rating for
your mobile phone. The more immune your hearing aid is, the
less likely you are to experience interference noise from mobile
phones.
Your phone complies with the standards set by these reports
and the FCC guidelines.
E911 mandates
Where service is available, this phone complies with the Phase I
and Phase II E911 Mandates issued by the FCC.
For more information about hearing aid compatibility, visit the
FCC’s Consumer & Governmental Affairs Bureau Web site at
.
User Guide
5
Kyocera Communications Inc.
To purchase accessories, visit
kyocera.superiorcommunications.com
6
Table of Contents
6
8
Change Alarm Clock Settings . . . . . . . . . .33
Images . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Messaging Menu . . . . . . . . . . . . . . . . . . . .38
Manage Browser Alerts . . . . . . . . . . . . . . .47
4
9
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . 22
Recent Calls . . . . . . . . . . . . . . . . . . . . . . 29
5
User Guide
7
Convenience . . . . . . . . . . . . . . . . . . . . . . . 61
Phone Info . . . . . . . . . . . . . . . . . . . . . . . . . 68
8
1
Get Started
Charge the Battery
1. Open the microUSB jack
cover on the top of the
Phone Battery
Install the Battery
1. With the back of the
phone facing you, press
on the back cover and
slide it to the bottom of
the phone.
phone. Connect the AC
adapter to the microUSB
jack.
2. Plug the adapter into a
wall outlet.
2. Lift the back cover from
the bottom to remove.
3. Place the battery in the
battery casing. The metal
contacts of the battery
must touch the metal
contacts of the battery
casing.
The battery icon in the upper-right corner of
the screen tells you whether the phone is:
–
–
–
Charging (the icon is animated)
Partially charged
Fully charged
!
You must have at least a partial charge in the
battery to make or receive calls. You can safely
recharge the battery at any time, even if it has a
partial charge.
Note: Before removing the battery, make sure
the phone is powered off.
4. Align the back cover
side tabs with the slots
on each side of the
!
phone.
5. Slide the back cover to
the top of the phone until
it is securely in place.
User Guide
9
•
•
Replace the battery only with another
qualified battery. Use of an unqualified
battery may present a risk of fire,
explosion, leakage, or other hazard. If you
are unsure about whether a replacement
battery is compatible, contact customer
support.
Promptly dispose of used batteries in
accordance with local regulations and
recycle if possible. Do not dispose as
household waste.
Battery Safety Guidelines
•
•
Do not disassemble or open the battery.
Do not crush, bend, deform, puncture, or
shred the battery.
•
•
Do not attempt to insert foreign objects into
the battery.
Do not immerse the battery or expose it to
water or other liquids. Even if a battery
appears to dry out and operate normally,
internal parts can slowly corrode and pose a
safety hazard.
•
•
Supervise all battery usage by children.
Avoid dropping the phone or battery. If the
phone or battery is dropped, especially on a
hard surface, an internal short-circuit can
occur and pose a safety hazard. If you
suspect battery damage, take it to a service
center for inspection.
•
Always keep the battery between 15 °C and
25 °C (59 °F and 77 °F). Do not expose the
battery to extremes of temperature (heat or
cold), fire, or other hazards such as a
cooking surface, iron, or radiator.
Never use any damaged battery.
Only use the battery for its intended phone.
Only use the battery with a qualified
charger. Use of an unqualified battery
charger may present a risk of fire,
explosion, leakage, or other hazard. If you
are unsure about whether a charger is
qualified, contact customer support.
Do not short-circuit the battery or allow
metallic conductive objects—such as keys,
coins, or jewelry—to contact the battery’s
terminals.
•
•
•
•
Improper battery use may result in a fire,
explosion, or other hazard.
Common Causes of Battery Drain
•
•
•
•
Playing games or using the Web.
Taking pictures with the flash on.
Keeping backlighting on.
Operating when far away from a base
station or cell site.
Using data cables or accessories.
Operating when no service is available, or
service is available intermittently.
High earpiece and ringer volume settings.
Repeating sound, vibration, or lighted
alerts.
•
•
•
•
•
10
Phone Battery
Phone Overview
Get to Know Your Phone
The following shows the phone’s keypad.
1. Earpiece speaker.
1
2
2. Home screen.
3. Left softkey selects items that appear on the lower left of
the display. At the home screen, you can select Menu
.
4. Navigation key scrolls through lists and text entry fields
and accesses the following shortcuts from the home
screen:
3
5
11
13
4
6
12
14
–
–
–
–
Scroll left to launch Browser.
_
_
+
O
(
T
)
Y
@
P
#
1
W
2
E
3
R
Scroll right to go to Tools & Games > Voice Memo
.
Q
U
I
‘
/
G
:
;
$
K
!
L
4
S
5
D
6
F
*
H
J
?
A
Scroll up to create a custom menu shortcut.
%
V
=
B
&
N
7
Z
8
X
9
C
‛
‛‛
.
7
Fn
M
Scroll down to go to Recent Calls > All
.
0
CAP
Space
SYM
8
15
S2300
5. Speakerphone key activates the speakerphone and
answers calls.
6. Send key starts or answers a call. Press once to display
the recent calls list or twice to redial the last number
dialed. Press and hold to activate voice commands.
9
10
7. Function key enables you to type symbol characters or toggle between letters and symbols.
Press the Function key once to change the input mode for the next character; press twice
(within 2 seconds) to toggle between letters and symbols.
8. Shift key enables you to press once to change case mode or press twice to toggle between case
modes.
9. Number keypad for entering numbers.
10. QWERTY keypad for entering numbers, letters, or symbols.
11. Right softkey selects items that appear on the lower right of the display. At the home screen,
you can select Contacts
.
12. OK key selects a menu item or option. At the home screen, you go to the main menu when you
press the OK key.
13. Back key returns you to the previous screen. At the home screen, you activate the keyguard
when you press and hold the Back key.
14. End key turns the phone on and off, ends a call or browser session, and returns you to the
home screen.
15. Enter key generates a carriage return in text entry.
User Guide
11
The following shows the back of the phone.
1. Jack for a hands-free headset (sold separately).
2. Camera lens.
3. Accessory eyelet (for optional straps and lanyards).
4. Jack for AC adapter (included) and microUSB cable (sold
separately).
1
2
4
5
3
6
7
5. External speaker.
6. Camera key activates camera mode. Press and hold the
Camera key to activate camera mode.
7. Volume key raises or lowers ringer volume.
Warning: Inserting an accessory into the incorrect jack will
damage the phone.
Qualcomm
3G CDMA
Screen Icons
These icons may appear on your phone’s screen.
Bluetooth wireless technology is disabled
(Off).
The phone is operating in IS2000 (1X)
digital mode.
Bluetooth wireless technology is enabled
(On).
The phone is in airplane mode.
The alarm clock is set.
The phone is in camera mode.
The battery will not charge.
The phone is set to auto answer.
The battery is fully charged. The more black
bars, the greater the charge.
Data service is available and active on your
phone. Check with your service provider for
availability.
The phone is transferring data with
Bluetooth.
Data service is available, but the phone is
dormant.
A headset or other hands free device is in
operation.
(blinking) The phone is receiving
high-speed data.
A headset or other hands free device is
transferring data.
12
Phone Overview
(blinking) The phone is sending high-speed
data.
The phone is in privacy mode or is
accessing a secure Web site.
The phone is operating in IS95 digital
mode.
The phone is receiving a signal. You can
make and receive calls. Fewer bars indicate
a weaker signal.
Content is DRM protected.
The speaker phone is turned on.
A T-coil hearing aid is in operation.
A traffic channel is active.
Position location is set to emergency
services only.
Position location is set to your service
provider and to emergency services.
The phone is in TTY device mode.
The phone has a high speed data
connection.
The phone is set to vibrate or to vibrate and
then ring.
A call is in progress.
The phone is set to light up instead of ring.
New message.
New photo and text message.
New photo and voice message.
New photo message.
New photo, voice and text message.
New text message.
New voice and text message.
New voice message.
The phone is not receiving a signal. You
cannot make or receive calls.
The phone is roaming outside of its home
service area.
User Guide
13
Main Menu
From the home screen, press the OK key or select Menu to access the main menu.
Idle State >
Menu
Level 1 >
Contacts
Level 2
Access these options: View All Add New, Groups, Speed
,
Dial List
,
Voice Dial List, Erase Contacts, and Contacts
Count
.
Recent Calls
Access these options: All
,
Incoming, Outgoing, Missed,
Erase Call List Call Timers, and Kilobyte Counter
,
.
Browser
Browse the web.
Set an alarm.
Alarm Clock
Media Gallery
Messaging
Access these options: Images
,
Sounds, and Delete All
.
Access these options: New Text Msg
,
New Pic Msg
,
Voicemail Inbox Browser Alerts Sent Msgs
,
,
,
,
Outbox,
Saved Msgs
,
Drafts Msg Settings Erase Msgs, and
,
,
Message Count
.
Camera
Scheduler
Settings
Take a picture.
Schedule an appointment.
Access these options: Bluetooth
,
Browser
,
Sounds
,
Display
,
Convenience
,
Voice Features
,
Accessories
,
Network
,
Security, and Phone Info
.
Downloads
Download an application.
Tools & Games
Access these options: Brick Attack
Scheduler Alarm Clock
Timer Stopwatch
,
Voice Memo,
,
,
Tip Calculator, Calculator,
,
,
Memopad, and World Clock
.
Bluetooth
Access these options: On/Off My Devices, and Settings.
,
Note: The menu items on your phone can change depending on the options provided by your service provider.
Check with your service provider.
14
Main Menu
Guide Conventions
In this guide, the following conventions are
used when describing phone features.
Select means to press the Left softkey, Right
softkey or OK key to select an item seen on the
display. For example, “Select Menu” tells you
to physically press the left softkey to choose
Menu from the display.
Press means to press a phone key. For
example, “Press the Send key to make a phone
call” tells you to physically press the Send key
on your phone.
Scroll means to use the Navigation key to
move through a list on the display. For
example, “Scroll through your contacts list to
choose a contact” means to physically press the
Navigation key up or down to scroll through
the list on the display.
>
(greater than symbol) tells you to select an
option from a menu or list. For example,
Menu Settings” means to:
“
>
1. Press the left softkey to select Menu
.
2. Scroll to the Settings option.
3. Press the OK key to select Settings
.
User Guide
15
2
Call Features
This section describes the basic features related
to calls.
Call Using Voice Commands
You can use voice commands to call a contact
from your voice dial list or to dial a phone
Power Phone Up
•
To turn your phone on, press the End key
and wait until the phone display lights up.
To turn your phone off, press and hold the
End key until the phone plays a short
musical sound and turns off.
Redial a Number
1. Press the Send key to open your call
history.
2. Highlight a phone number or contact and
press the Send key.
Note: To redial the last number called,
received or missed, press the Send key twice.
•
Make Phone Calls
Make sure you are in an area where a signal
can be received. Look for the signal strength
icon on the home screen. The more bars, the
stronger the signal. If there are no bars, move
to where the signal strength is better.
When the phone has been idle for a time, it
cycles into power save mode. Press any key to
return to normal operating mode.
Answer Phone Calls
When a call comes in, the phone rings,
vibrates, or lights up. The phone number of the
caller also appears if it is not restricted. If the
number is stored in your contacts list, the
contact’s name appears. There are several ways
you can answer a phone call.
There are several ways you can make a phone
call.
Answer Using Earpiece
Call Using a Number
1. Enter a phone number.
2. Press the Send key.
Press the Send key.
Answer Using Speakerphone
Press the Speakerphone key.
Call Using a Contact
1. From View All, highlight a contact.
2. Press the Send key.
End Phone Calls
Press the End key.
16
Power Phone Up
Activate Voice Dialing
Use Speed Dialing
1. Press and hold the Send key.
2. Follow the prompts.
Speed dialing allows you to assign a one- or
two-digit shortcut to a contact. Before you can
use speed dialing you must save a phone
number as a contact and assign a speed dial
location to it. See “Assign Speed Dials to
Contacts” on page 25.
Volume Control
Adjust Volume during a Call
Press the Volume key up or down to adjust the
earpiece volume during a call.
To call a contact that has a speed dial location:
1. Enter the one- or two-digit speed dial
location.
2. Press the Send key.
Use the Speakerphone
Your phone has a built-in speakerphone.
Emergency Services
•
To turn on the speakerphone, press the
Speakerphone key. The speakerphone icon
appears on the home screen when the
speakerphone is on.
To turn off the speakerphone, press the
Speakerphone key again.
Call Emergency Services
You can call an emergency code even if your
phone is locked or your account is restricted.
When you call, your phone enters emergency
mode. This enables the emergency service
exclusive access to your phone to call you
back, if necessary. To make or receive regular
calls after dialing the code, you must exit this
mode.
•
Note: If you press the Speakerphone key
during an incoming call, you will answer the
call.
To dial an emergency code:
1. Enter the 3-digit emergency code.
2. Press the Send key.
Note: Regardless of the 3-digit emergency
code (911, 111, 999, 000, etc.), your phone
operates as described above.
Silence an Incoming Call
•
To silence the phone without answering the
call, press the Back key or press the
Volume key up or down.
•
To silence the phone and answer the call,
press the Back key or press the Volume
key up or down and then press the Send
key.
User Guide
17
3
Text Entry
You can enter letters, numbers, and symbols in
contacts, text messages, and your banner.
Enter Numbers with QWERTY Keypad
From the text entry field, select Options >
Numbers Only and press the number key to
enter your number.
Text Entry Modes
The text entry screen has the following
features:
The
icon indicates you are in Numbers
Only mode. Press the Function key twice
quickly (within two seconds) to change modes.
Press the Function key once to change the
mode for the next character only.
1. Characters remaining
that you can type.
Allowed message
length can vary
depending on your
service.
Enter Letters with QWERTY Keypad
From the text entry field, select Options >
Normal Alpha to enter letters. You can enter
text in the following ways:
2. Text entry fields.
3. Current capitalization setting.
4. Current text entry mode.
Note: The entry mode will default depending
on the task you are doing. For example, when
entering a phone number, you are in Numbers
Only mode. When entering a name for a
contact, you are in Normal Alpha mode.
•
To enter a letter, press the key for the letter.
Press the Shift key to change the case of a
letter. Press the Shift key twice quickly
(within two seconds) to change case modes.
Press the Space key to enter a space.
To enter a number or symbol, press the
Function key and then the key for the
number or symbol.
•
The
icon indicates that you are in Normal
Alpha mode. Press the Function key twice
quickly (within two seconds) to change modes.
Press the Function key once to change the
mode for the next character only.
User Guide
19
Rapid Entry with QWERTY Keypad
When you press a series of keys using Rapid
entry, your phone checks its dictionary and
guesses at the word you are trying to spell.
From a text entry field, select Options >
Rapid Entry to speed up word completion. To
enter words, press a key once. For example, to
enter the word “Wyoming” press the w > y > o
keys and then the OK key.
The
icon indicates you are in Rapid Entry
mode. To change case mode, press the Shift
key.
Enter Symbols with QWERTY Keypad
While entering text in Normal Alpha mode,
press the Function key and then the key for the
number or symbol. To access more symbols,
do one of the following:
•
Press the Symbol key and then the key for
the symbol.
•
Select Options > Add Symbols and then
the key for the symbol.
20
Text Entry Modes
Text Entry Quick Reference
This table gives instructions for entering letters, numbers, and symbols.
To..
Do this..
Enter a letter
Enter a number
Enter a symbol
In Normal Alpha mode, press a key.
In Numbers Only mode, press a key.
Use Normal Alpha mode, press the Function key and
then a key.
Enter a space
Press the Space key.
Erase a character
Press the Back key.
Erase all characters
Move the cursor right or left
Move the cursor up or down
Change input mode
Change case mode
Press and hold the Back key.
Scroll left or right.
Scroll up or down.
Press the Function key twice quickly.
Press the Shift key twice quickly.
Capitalize any letter
In Normal Alpha mode, press the Shift key. Choose
uppercase.
Lowercase any letter
In Normal Alpha mode, press the Shift key. Choose
lowercase.
Initial caps
In Normal Alpha mode, press the Shift key. Choose
sentence case.
Select an option at the bottom of the screen
Press the appropriate left or right softkey.
User Guide
21
4
Contacts
Use Contacts to store information about a person or company.
Contacts Menu
Select Contacts from the main menu to access the following functions:
Level 1 >
Contacts
Level 2 >
Level 3
View All
Access your existing contacts list.
Add a new entry to your contacts list.
View your groups of contacts.
Add New
Groups
Speed Dial List
Voice Dial List
Erase Contacts
View your contacts assigned with speed dials.
View your contacts assigned with voice dials.
Access these options: Contacts Only
,
Groups Only, Erase
All.
Contacts Count
Check how much contact space you have used.
22
Contacts Menu
Access Contacts
Add Contacts
Access Contacts List
1. From View All, enter the first letter of your
desired contact and scroll to highlight it.
2. Do one of the following:
Add Contacts from Home Screen
1. From the home screen, enter a phone
number to save (include the area code).
2. Select Save > Save New Contact
.
–
–
Press the Send key to call the contact.
Press the OK key to view the contact’s
details.
Select New to create a new contact.
Select Options to access more
functions.
3. Enter a name for the contact.
4. Enter additional phone numbers, email
addresses, and other contact details. (Scroll
up or down to move through the contact
fields.)
–
–
5. When done, select Save
.
View Contact Details
1. From View All, select a contact.
2. At the contact details screen, highlight a
number, address or note.
Add Contacts from Contacts Menu
1. From Add New, enter a name for the
contact. Scroll down to the next field when
done.
3. Select the detail you want to view. For
example, to view a phone number, select
2. Enter a primary number for the contact.
3. Enter additional phone numbers, email
addresses, and other contact details. (Scroll
up or down to move through the contact
fields.)
Options > View Number
.
Use Frequent List
With Frequent List enabled, you can view 15
of your most frequently called contacts. See
“Enable Frequent List” on page 63.
4. When done, select Save
.
Use Fast Find
With Fast Find enabled, you can press one or
two keys to view closer matches in your
contacts list. See “Call Contact using Fast
Find” on page 63.
User Guide
23
Add a Code or Extension
When saving the phone number of an
automated service, you may include a pause
for dialing an extension.
1. From the home screen, enter a phone
number.
Send a Multimedia Message to
Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight a
number or email address.
3. Select Options > Send Pic Msg
4. Complete your multimedia message and
select Send
.
2. Select Options and a type of pause:
.
–
Time Pause causes the phone to stop
dialing for two seconds.
Send a Contact vCard
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
–
Hard Pause causes the phone to wait
until you select Release while making
the call.
3. Enter the remaining numbers and select
Save > Save New Contact
4. Complete the contact information and
select Save
3. Select Options > Send as vCard > Via
MMS Msg (to attach to a multimedia
message), Via Bluetooth (to send to a
Bluetooth-enabled device), or To Printer
(to print on a Bluetooth-enabled device).
4. Complete the appropriate task to send the
contact information.
Note: If your phone has no Bluetooth feature,
you may send the contact information with a
message only.
.
.
Use Contacts
Call Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight a
number.
Customize Contacts
Edit Contact Details
1. From View All, select a contact.
3. Select Options > Call
.
Send a Text Message to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight a
number or email address.
2. At the contact details screen, select Edit
.
3. Enter additional phone numbers, email
addresses, and other contact details. (Scroll
up or down to move through the contact
fields.)
3. Select Options > Send Text Msg
4. Complete your text message and select
Send
.
4. When done, select Save
.
.
24
Use Contacts
Assign Number Types
1. From View All, select a contact.
2. At the contact details screen, select Edit
Add a Prefix to Phone Numbers
Use Prepend to add a prefix, such as an area
code, to a phone number:
.
1. From View All, select a contact.
2. At the contact details screen, highlight a
number.
3. Select Options > Prepend to enter the
prefix at the beginning of the number.
3. Press down twice to scroll to the number
type dropdown and press the OK key.
4. Select a number type. The appropriate icon
appears next to the number in your contacts
list.
5. Select Save
.
4. Select Save.
Assign Ringers to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
Assign Speed Dials to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight a
number.
3. Select Options > Ringer > Assign Ringer
and a ringer from the list. (Scroll to play the
ringers.)
3. Select Options > Add Speed Dial.
4. Select a location from the list to assign the
speed dial number.
Assign Message Tones to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
3. Select Options > Msg Tone > Assign Msg
Tone and a ringer from the list. (Scroll to
play the ringers.)
Change Primary Numbers
When a contact has more than one number, the
first number becomes the primary number by
default. To change the contact’s primary
number:
1. From View All, select a contact.
2. At the contact details screen, highlight a
number.
Assign Pictures to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
3. Select Options > Primary Number > Yes
.
3. Select Options > Picture > Assign Picture
to assign a picture.
User Guide
25
Add Contacts to Groups
1. From View All, select a contact.
2. At the contact details screen, highlight a
number or email address.
Erase All Contacts
From Erase Contacts, select Contacts Only >
Yes > Yes to erase all your contacts.
Note: You cannot recover deleted information.
3. Select Options > Add to Group
.
Erase All Contacts and Groups
From Erase Contacts, select Erase All > Yes
> Yes to erase all your contacts and groups.
Note: You cannot recover deleted information.
4. Select groups from the list provided. A
checkmark appears next to each selection.
You can also remove a checkmark.
5. When finished, select Done
.
Visit Web Addresses
1. From View All, select a contact.
2. At the contact details screen, highlight a
Web address.
Contact Groups
You can assign your contacts to groups. Your
phone comes with default groups. You can also
create your own groups.
3. Select Options > Launch Web
.
View Groups
1. Select Groups to view your preloaded
groups, followed by the custom groups you
have created.
2. Highlight a group and do one of the
following:
Erase Contacts
Erase Contact Details
1. From View All, select a contact.
2. At the contact details screen, highlight a
number, address or note.
–
Press the OK key to view the group
details.
3. Select your desired erase option and then
select Yes. For example, to erase an email
address, select Options > Erase Address >
–
–
Select New to create a new group.
Select Options to access more
functions.
Yes
.
Erase an Entire Contact
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
3. Select Options > Erase Contact > Yes to
erase the entire contact.
26
Erase Contacts
Create a New Group
Assign Ringers to Groups
1. From Groups, select a group.
2. At the group details screen, scroll to the
group name.
3. Select Options > Ringer > Assign Ringer
and a ringer from the list. (Scroll to play the
ringers.)
1. From Groups, select New
.
2. Enter a name for the group and select Next
3. Select contacts from the list provided. A
checkmark appears next to each selection.
You can also remove checkmarks.
.
4. When finished, select Done
.
Your new group appears the next time you
view your groups list.
Assign Message Tones to Groups
1. From Groups, select a group.
2. At the group details screen, scroll to the
group name.
Send Text Messages to Groups
1. From Groups, highlight a group.
3. Select Options > Msg Tone > Assign Msg
Tone and a ringer from the list. (Scroll to
play the ringers.)
2. Select Options > Send Text Msg
3. Complete your text message and select
Send
.
.
Assign Pictures to Groups
1. From Groups, select a group you have
created.
2. At the group details screen, scroll to the
group name.
Send Multimedia Messages to Groups
1. From Groups list, highlight a group.
2. Select Options > Send Pic Msg
3. Complete your multimedia message and
select Send
.
.
3. Select Options > Picture > Assign Picture
to assign a picture.
Add or Remove Contacts from Groups
1. From Groups, highlight a group.
Send a Group vCard
1. At the Groups list, highlight a group.
2. Select Options > Send > Via Bluetooth
3. Complete the appropriate task to send the
group information.
2. Select Options > Edit
.
3. If you are modifying a group you created,
.
select Next. Otherwise, go to the next step.
4. Select contacts from the list provided. A
checkmark appears next to each contact in
the group. Press the OK key to add or
remove checkmarks.
5. When finished, select Done
.
User Guide
27
Erase a Group
Voice Dial List
Enable Voice Dial Tags
1. From Groups, highlight a group.
2. Select Options > Erase > Yes
.
Your phone creates a voice dial tag for each
contact that has a name field which is not blank
or a name that is more than five syllables. You
can enable or disable the voice dial tags
associated with your contacts.
1. From Voice Dial List, press the OK key to
add or remove checkmarks. A checkmark
appears next to each enabled voice dial.
(Scroll through the list to play the voice
dial tags.)
Erase All Groups
From Erase Contacts, select Groups Only >
Yes > Yes to erase all your groups.
Note: You cannot recover deleted information
or erase preloaded groups.
Speed Dial List
Assign Speed Dial Numbers
1. From Speed Dial List, highlight an
unassigned number (marked as empty).
2. When done, select Save
.
Search Contact Voice
You can use voice commands to find a contact
in your voice dial list. For more information,
2. Select Assign
.
3. At the contacts list, select a contact.
4. At the contact details screen, select a phone
number.
Clear Speed Dial Numbers
1. From Speed Dial List, highlight an
assigned number.
Check Contacts
Select Contacts Count to check how many
contacts you have stored.
2. Select Erase > Yes
.
28
Speed Dial List
5
Recent Calls
Recent Calls Menu
Select Recent Calls from the main menu to access the following functions:
Level 1 >
Level 2 >
All
Level 3
Recent Calls
See a list of all voice calls.
Incoming
Outgoing
Missed
See a list of all voice calls you have received.
See a list of all voice calls you have made.
See a list of all voice calls you have missed.
Erase Call List
Call Timers
Access these options: All
,
Incoming
,
Outgoing, and Missed
.
Access these options: Life Timer
,
Recent Calls Home
,
Calls Roam Calls Incoming Calls, and Outgoing Calls.
,
,
Kilobyte Counter
See how much data you have sent and received.
Return a Received Call
Work with Call Lists
Return Any Call
1. From All, highlight a number.
2. Press the Send key to call the number or
select Options to access more features.
This list contains all calls made and received.
1. From Incoming, highlight a number.
2. Press the Send key to call the number or
select Options to access more features.
This list contains all calls received.
Return an Outgoing Call
1. From Outgoing, highlight a number.
2. Press the Send key to call the number or
select Options to access more features.
This list contains all calls you have made.
User Guide
29
Send Text Message from Call List
1. At a call list, highlight a contact.
Return a Missed Call
1. From Missed, highlight a number.
2. Press the Send key to call the number or
select Options to access more features.
This list contains all calls you received, but did
not answer.
2. Select Options > Send Text Msg
3. Complete your text message and select
Send
.
.
Send Multimedia Message from Call List
1. At a call list, highlight a contact.
Manage a Missed Call Alert
When you have missed a call, “Missed Call”
appears on your screen. You can do one of the
following:
2. Select Options > Send Pic Msg
3. Complete your multimedia message and
select Send
.
.
•
•
To clear the screen, select OK.
To view the call details, select Calls and
press the OK key.
Erase Call List Records
•
To return the call, select Calls and press the
Send key.
Erase a Single Record
1. At a call list, highlight a contact.
2. Select Options > Erase Record > Yes
.
Call List Options
Erase a Call List
Save Number from Call List
From Erase Call List, select a call list to erase
records from. For example to erase all records
from the incoming call list, select Incoming >
1. At a call list, highlight a number.
2. Select Options > Save
.
3. Select Save New Contact to create a new
contact or Add to Existing to add a number
to an existing contact.
Yes
.
Erase All Call Lists
From Erase Call List, select All > Yes to erase
all records from all call lists.
View Contact from Call List
1. At a call list, highlight a contact.
2. Select Options > View to see the contact
details screen.
30
Erase Call List Records
This timer tracks all roaming calls made and
received since you last reset the timer. To reset
Work with Call Timers
this timer to zero, select Reset > Yes
.
View All Calls Timer
Select Life Timer to view the number of calls
and the total call time. Select Done when
finished.
Your phone can alert you with a short beep ten
seconds before each minute passes during a
call. For more information, see “Enable Minute
Alert” on page 63.
This timer tracks all calls made and received
for life of the phone and cannot be reset.
View Incoming Calls Timer
Select Incoming Calls to view the number of
calls and the total call time. Select Done when
finished.
This timer tracks all calls received since you
last reset the timer. To reset this timer to zero,
View Recent Calls Timer
Select Recent Calls to view the number of
calls and the total call time. Select Done when
finished.
This timer tracks all calls made and received
since you last reset the timer. To reset this
select Reset > Yes
.
timer to zero, select Reset > Yes
.
View Outgoing Calls Timer
Select Outgoing Calls to view the number of
calls and the total call time. Select Done when
finished.
View Home Calls Timer
Select Home Calls to view the number of calls
and the total call time. Select Done when
finished.
This timer tracks all calls made and received in
your home network since you last reset the
timer. To reset this timer to zero, select Reset >
This timer tracks all calls made since you last
reset the timer. To reset this timer to zero,
select Reset > Yes
.
Yes
.
View Data Counter
Select Kilobyte Counter to view the amount
of kilobytes sent during data calls. Select Done
when finished.
View Roam Calls Timer
Select Roam Calls to view the number of calls
and the total call time. Select Done when
finished.
This timer tracks kilobytes sent during data
calls made, data calls received, and for the life
of the phone. To reset the data counter to zero,
select Options > Reset > Yes
.
User Guide
31
6
Browser
You can use your phone to browse the Internet
if you have obtained phone Internet services
from your service provider and if over-the-air
Internet access is available in your area.
•
Press the Back key to return to the previous
screen.
Press the End key to exit.
Select Options to access more browser
features.
•
•
Launch Browser
Add a Bookmark
Select Browser to launch the browser. An alert
appears notifying of airtime fees, if you have
enabled web alerts. Select OK to continue.
If this is the first time you have connected to
the Internet, a message informs you that
security is not yet enabled for your browser.
Select Yes to enable security.
1. Surf to the Web page you want to
bookmark and select Options > Add to
Bookmarks
.
2. Edit the bookmark’s details, if needed.
3. Select Options > Save to save the
bookmark.
To access your saved bookmarks, select
Options > Bookmarks from any web page.
Browse the Web
A browser home page with a list of bookmarks
and some browser menu options appear when
you are connected to the Web. The lock icon
appears in a secure session. You can do the
following:
•
To choose a site, scroll to the link and press
the OK key.
•
An underline and an arrow indicate that
there is more text. Scroll down to view the
rest of the text.
32
Launch Browser
7
Alarm Clock
You can set up to four alerts with your phone’s
three alarm clocks and one quick alarm.
Note: The alert occurs only if the phone is on.
Set the Quick Alarm
1. From Alarm Clock, scroll to the quick
alarm and select Set
.
2. Choose a time. (A notification shows the
quick alarm is on.)
When the quick alarm rings, select Off to turn
off the alarm, or Reset to set the quick alarm
again.
Set an Alarm
1. From Alarm Clock, scroll to one of the
alarms and select Set
2. Press the OK key to change the time, if
.
needed.
–
–
Scroll left or right to move between
hour, minute and AM/PM fields.
Scroll up or down to change hour,
minute and AM/PM.
Change Alarm Clock Settings
From Settings, you can modify the following
features.
Press the OK key to save time and move to
the next field.
3. Press the OK key to select a sound from the
list.
Set Snooze Duration
From Snooze Duration, select an option to set
how long before the alarm goes off again when
you hit the snooze.
4. Press the OK key to select a recurring
alarm from the list, if needed.
5. Press the OK key to enter a note.
Set Snooze Limit
From Snooze Limit, select an option to set
how many times you can hit the snooze.
6. Select Save
.
When the alarm rings, select Stop to turn off
the alarm or Snooze to set the alarm to ring in
another ten minutes.
User Guide
33
8
Media Gallery
Use Media Gallery to retrieve and playback media files and other downloads.
Media Gallery Menu
Select Media Gallery from the main menu to access the following functions:
Level 1 >
Level 2 >
Images
Level 3
Media Gallery
Access these options: Camera Pictures Saved Images,
,
Wallpapers
,
Wallpaper Shuffle
,
Screensavers, and Caller
Ringers Ringer
Images Only
IDs.
Sounds
Access these options: Saved Sounds
Shuffle, and Voice Memos
,
,
.
Delete All
Access these options: Camera Pics Only
Sounds Only, and Delete All
,
,
.
Send an Image
Images
Send a Picture
1. From Camera Pictures, select a picture.
2. Select Send > Via EMS Msg (to attach to
an enhanced message), Via MMS Msg (to
attach to a multimedia message), Via
Bluetooth (to send to a Bluetooth-enabled
device), or To Printer (to print on a
1. From Saved Images, select an image.
2. Select Send > Via EMS Msg (to attach to
an enhanced message), Via MMS Msg (to
attach to a multimedia message), Via
Bluetooth (to send to a Bluetooth-enabled
device), or To Printer (to print on a
Bluetooth-enabled device).
3. Complete the appropriate task.
Note: If your phone has no Bluetooth feature,
you may send the file with a message only.
Bluetooth-enabled device).
3. Complete the appropriate task.
Note: If your phone has no Bluetooth feature,
you may send the file with a message only.
34
Media Gallery Menu
Change the Default Wallpaper
Assign a Ringer
1. From Wallpapers, select a wallpaper.
1. From Ringers, highlight a ringer.
2. Select Assign and choose how you want to
assign the ringer.
2. Select Set Default
.
Edit the Wallpaper Shuffle
3. Complete the appropriate task.
1. From Wallpaper Shuffle, select Edit. With
no wallpapers saved, you need to add files.
2. Select Add to include a file in the shuffle,
Remove to remove a file from the shuffle,
or Options to access more features.
Edit the Ringer Shuffle
1. From Ringer Shuffle, select Edit
2. Select Add to include a file in the shuffle,
Remove to remove a file from the shuffle,
or Options to access more features.
.
3. When finished, select Options > Done
.
3. When finished, select Options > Done
You can only edit the shuffle with at least a file
added.
.
Change the Default Screensaver
1. From Screensavers, select a screensaver.
2. Select Set Default
.
Play a Voice Memo
Assign a Caller ID
1. From Voice Memos, highlight a memo you
have recorded.
1. From Caller IDs, select an image.
2. Select Assign
.
2. Select Play
.
3. At the contacts list, select a contact.
Use the Navigation key to control the
playback tools displayed.
Sounds
Send a Sound
Media File Options
1. From Saved Sounds, highlight a sound.
2. Select Send > Via EMS Msg (to attach to
an enhanced message), Via MMS Msg (to
attach to a multimedia message), or Via
Bluetooth (to send to a Bluetooth-enabled
device).
3. Complete the appropriate task.
Note: If your phone has no Bluetooth feature,
you may send the file with a message only.
Rename a File
1. From a media file list, highlight a file.
2. Select Options > Rename
3. Enter a new name and select Save
You can only rename unlocked files. Preloaded
files on your phone are always locked.
.
.
User Guide
35
Send a File
Play a File
1. From a media file list, highlight a file.
2. Select Options > Send > Via EMS Msg
(to attach to an enhanced message), Via
MMS Msg (to attach to a multimedia
message), Via Bluetooth (to send to a
Bluetooth-enabled device), or To Printer
(to print on a Bluetooth-enabled device).
The options available depend on the file
type.
1. From a media file list, highlight a file.
2. Select Options > Play
Use the Navigation key to control the
playback tools displayed.
.
Add Files to a Shuffle
1. From a media file list, highlight a file.
2. Select Options > Shuffle to add the file to
the applicable shuffle.
3. Complete the appropriate task.
Note: If your phone has no Bluetooth feature,
you may send the file with a message only.
View File Details
1. From a media file list, highlight a file.
2. Select Options > Details to view the
details such as file size or save date.
3. Select OK to exit.
Send a File to an Online Location
1. From a media file list, highlight a file.
2. Select Options > Send to Online
.
Modify a File
1. From a media file list, select a file.
Assign a File
1. From a media file list, highlight a file.
2. Select Options > Assign and choose how
to assign the file.
2. Select Options > Modify.
3. Select Options and an option to rotate,
resize, and so on.
3. Complete the appropriate task.
4. When done, select Save to save over an
existing file or as a new one.
Lock a File
1. From a media file list, highlight a file.
2. Select Options > Lock to protect a file
from being accidently erased. To unlock the
Use the Zoom
1. From a media file list, select a file.
2. Select Options > Zoom
.
file, select Options > Unlock
.
3. Use the Navigation key to zoom in and out.
4. Select Cancel to exit.
36
Media File Options
View a Slideshow
Erase All Image Files
1. From Camera Pictures, select Options >
Slideshow to play the slideshow of the files
contained in the current folder.
From Delete All, select Images Only > Yes to
erase all files in the Images folder.
Note: You can only erase unlocked files.
Preloaded files on your phone are always
locked.
2. Select Pause (to stop), Play (to resume), or
Options (to access more features).
With Options selected, your phone
automatically pauses the slideshow.
Erase All Sound Files
From Delete All, select Sounds Only > Yes to
erase all files in the Sounds folder.
Note: You can only erase unlocked files.
Preloaded files on your phone are always
locked.
3. When you are done, select Options > Exit
.
Erase Media Files
Erase a Single File
1. From a media file list, highlight a file.
2. Select Options > Erase > Yes
You can only erase unlocked files. Preloaded
files on your phone are always locked.
Erase All Media Files
.
From Delete All, select Delete All > Yes to
erase all files in the Media Gallery folder.
Note: You can only erase unlocked files.
Preloaded files on your phone are always
locked.
Erase All Files in a Folder
From a media file list, select Options > Erase
All > Yes
.
Note: You can only erase unlocked files.
Preloaded files on your phone are always
locked.
Erase All Pictures
From Delete All, select Camera Pics Only >
Yes to erase all files in the Camera Pictures
folder.
Note: You can only erase unlocked files.
User Guide
37
9
Messaging
Use Messaging to send, receive, and erase messages from your phone.
Messaging Menu
Select Messaging from the main menu to access the following functions:
Level 1 >
Level 2 >
Level 3
Messaging
New Text Msg
New Pic Msg
Voicemail
Inbox
Compose a text message.
Compose a multimedia message.
Shows how many voicemails are waiting.
Shows a list of received text and multimedia messages.
Shows how many alerts are waiting.
Shows a list of messages you have successfully sent.
Browser Alerts
Sent Msgs
Outbox
Shows a list of messages you have sent, but are pending or
failed.
Saved Msgs
Drafts
Shows a list of messages you have saved.
Shows a list of messages that have been started, but saved to
be completed at a later time.
Msg Settings
Access these options: Alerts
Signature QuickText Auto Retrieve
Callback Number Save to Sent
Text Msg Receipt
and Erase Recent List
,
Chat View
,
Msg List View
,
,
,
,
CC and BCC,
,
,
,
Auto-Erase
,
Default Text
,
Pic Msg Receipt, Voicemail Number,
.
Erase Msgs
Access these options: Inbox
,
Outbox, Sent Msgs, Saved
Msgs Drafts, and All
,
.
Message Count
Check how many messages you have.
Note: The menu items on your phone can change depending on the options provided by your service provider.
Check with your service provider.
38
Messaging Menu
recently used addresses. Scroll down to
move to the next field when done.)
You can message up to ten recipients at
once. Use comma or spaces to separate
addresses.
Send Messages
Create a Text Message
You can only send text messages to phone
numbers capable of receiving them or to email
addresses if supported.
1. From New Text Msg, enter a recipient’s
phone number or email address. (Select
Options to access contacts, groups or
recently used addresses. Scroll down to
move to the next field when done.)
You can message up to ten recipients at
once. Use comma or spaces to separate
addresses.
2. Repeat the first step for CC and BCC, if
needed.
3. Enter a subject.
4. Enter a message.
5. Attach an image file. (Select Options to
access more features.)
6. Attach a sound file. (Select Options to
access more features.)
7. When done, select Send
.
2. Enter the message. (Select Options to
access more features.)
3. When done, select Send
Receive Calls while Creating Messages
If you receive a call while creating a message a
notification appears. Do one of the following:
.
Create a Multimedia Message
You can only send multimedia messages to
phone numbers capable of receiving them or to
email addresses. If the character and file size
limit for a single multimedia message is
exceeded, the message must be edited to meet
the size limitation.
•
Select Ignore to ignore the call and return
to the message screen.
Press the Send key to answer the call and
your phone automatically saves the
•
message to Drafts
.
Enter Message Recipients
The following describes how to add recipients
to your messages, depending on the services
provided. Check with your service provider for
availability.
Note: Multimedia messaging is not available
on all phones. Check with your service
provider.
1. From New Pic Msg, enter a recipient’s
phone number or email address. (Select
Options to access contacts, groups or
User Guide
39
Add Recipients from Contacts
Save Recipients as Contacts
1. At the compose message screen, select
Options > Contacts when entering a phone
number or email address.
1. At the compose message screen, select
Options > Save Address when entering a
phone number or email address.
2. Select a contact from the contacts list.
3. Select a number or address.
4. Complete your message.
2. Select a number or address.
3. Select Options > Save New Contact (to
create a new contact) or Options > Add to
Contact (to add the number or address to
an existing contact).
Add Recipients from Recent List
1. At the compose message screen, select
Options > Recent List when entering a
phone number or email address.
2. Select a number or address.
Add Recipients from Message Text
1. At the compose message screen, select
Options > Add Address when entering the
text to add more recipients.
2. Enter a number or address to add.
3. Complete your message.
3. Complete your message.
Add Recipients from Recent Calls
1. At the compose message screen, select
Options > Recent Calls when entering a
phone number or email address.
2. Select a number.
Send Messages to Online Location
1. At the compose message screen, select
Options > Online Album when entering a
phone number or email address to upload
the message to your online photo album.
2. Complete your message.
3. Complete your message.
Send to Groups
1. At the compose message screen, select
Options > Groups when entering a phone
number or email address.
2. Select a group.
3. Complete your message.
Save Messages to Drafts
At the compose message screen, select
Options > Save Message when entering the
text. Your phone saves the message to Drafts
for you to complete at a later time.
40
Send Messages
Add Memos to Messages
Complete Messages in Drafts
1. From Drafts, highlight your desired
message.
1. At the compose message screen, select
Options > Insert Note when entering the
text.
2. Select Edit or Options > Edit
.
2. Select a memo.
3. Complete your message.
3. Complete your message.
Use Preset Text
Add Pictures to Messages
Add Preset Text
1. At the compose message screen, select
Options > Insert Picture when entering
the text.
2. Select a file.
3. Complete your message.
1. At the compose message screen, select
Options > Insert QuickText when
entering the text.
2. Select a preset text entry.
3. Complete your message.
Add Sounds to Messages
Save Messages as Preset Text
1. At the compose message screen, select
Options > Insert Sound when entering the
text.
2. Select a file.
3. Complete your message.
1. At the compose message screen, select
Options > Save as QuickText when
entering the text to use it later as preset text.
2. Complete your message.
Save Received Messages as Preset Text
Add Contacts to Messages
When viewing a received message, select
Options > Save as QuickText to use it later as
preset text.
1. At the compose message screen, select
Options > Insert Contact when entering
the text.
2. Select a contact from your contacts list.
3. Complete your message.
Attaching Files to Messages
The following describes how to select Options
to add various files to your messages when
entering the text, depending on the services
provided.
User Guide
41
Add Slides to Messages
Record Sounds for Messages
Use slides in a multimedia message to send
multiple files of the same type, such as pictures
or voice memos. A multimedia message may
have up to ten slides.
1. At the compose message screen, select
Options > Add New Slide when entering
the text.
1. At the compose message screen, select
Options > Record Sound when adding a
sound.
2. Record a sound.
3. Select it to add to your message.
4. Complete your message.
2. Select a slide and add more files or text if
Set Writing Language
needed.
1. At the compose message screen, select
Options > Writing Language to change
the language you compose your message
in.
To navigate through the slides, select
Options > Next Slide or Previous Slide
.
To erase the current slide, select Options >
Erase Slide
.
3. Complete your message.
You can only attach a limited number of files.
2. Complete your message.
Preview Messages
Add Media Files to Messages
1. At the compose message screen, select
Options > Media Gallery when adding a
media file.
2. Select a file to add to your message.
To remove a media file, select the
applicable option. For example, to remove
a sound, select Options > Remove Sound
3. Complete your message.
1. At the compose message screen, select
Options > Preview Message when
entering the message or media file.
2. Do one of the following:
–
–
–
If the message has more than one slide,
select Next to view the next slide.
If the message has only one slide, select
Send to send message.
.
Select Options to access more features.
Take Pictures for Messages
Set Individual Message Settings
The following describes how to set message
settings for individual messages.
1. At the compose message screen, select
Options > Take a Picture when adding an
image.
2. Take a picture.
3. Select it to add to your message.
4. Complete your message.
Note: Your selection of each of the following
message settings overrides that selected for all
messages from Msg Settings
.
42
Send Messages
6. Select Done
.
Request a Message Receipt
7. Complete your message. Your phone will
1. When entering a message, select Options >
Msg Settings > Msg Receipt > Request to
request a message delivery notice.
save the message and send it later.
Set the Validity Period
1. When entering a message, select Options >
2. Complete your message.
Msg Settings > Validity Period
.
Set Message Priority
2. Select Set Time to set how long to keep
your message valid before removing it
from the phone if not sent.
1. When entering a message, select Options >
Msg Settings > Set Priority to set the
priority level.
3. Press the OK key to change the time.
2. Complete your message.
–
Scroll left or right to move between the
hour, minute, and AM/PM.
Change the Callback Number
1. When entering the message, select Options
> Msg Settings > Callback Number
2. Enter your callback number and select OK
–
Scroll up or down to change the hour,
minute, and AM/PM.
.
4. Select Next
.
.
5. Press the OK key to change the date.
3. Complete your message.
–
–
Scroll left or right to move between the
month, day, and year.
Scroll up or down to change the month,
day, and year.
Send Messages Later
1. When entering a message, select Options >
Msg Settings > Send Later
.
2. Select Immediate or Set Time to set a
6. Select Done
.
specific time to send the message.
7. Complete your message.
3. Press the OK key to change the time.
–
Scroll left or right to move between the
hour, minute, and AM/PM.
Set the Slide Interval
1. When entering the message, select Options
> Msg Settings > Slide Interval
2. Select a time interval for the slides.
3. Complete your message.
–
Scroll up or down to change the hour,
.
minute, and AM/PM.
4. Select Next
.
5. Press the OK key to change the date.
–
–
Scroll left or right to move between the
month, day, and year.
Scroll up or down to change the month,
day, and year.
User Guide
43
1. At a message notification, select View (to
view the message) or Later (to check it
later).
2. After viewing the message, select Reply or
Options > Reply if the message has more
than one slide.
Set CC and BCC Fields
1. When entering the message, select Options
> Msg Settings > CC and BCC to enable
or disable the CC and BCC address fields.
2. Complete your message.
Select Options to access more features.
3. Complete your message and select Send
Manage Received Messages
.
Reply to Text Messages
Reply to Multimedia Messages (with
Prompt)
When receiving a message, your phone
displays a notification and the message icon
appears at the top of your screen. The message
icon flashes with an urgent message alert if the
message is urgent.
When receiving a message in prompt mode,
your phone displays a notification showing a
new message is available for download.
1. At the download notification, select Yes (to
download the message) or Options (to
retrieve it later or erase it without
downloading).
2. At the message notification, select View (to
view the message) or Later (to check it
later).
1. When a message notification appears,
select Inbox (to view the message) or
Ignore (to clear the notification).
An icon appears at the top of your screen
when you have an unread message.
2. From Inbox, highlight a message and select
View > Reply (to compose your message)
or Options (to access more features).
3. Select Reply or Options > Reply if the
message has more than one slide.
Select Options to access more features.
3. Complete your message and select Send
.
Reply to Multimedia Messages (with
Auto Retrieve)
When receiving a message in auto retrieve
4. Complete your message and select Send
.
Select Options to access more features.
Forward Messages
1. When viewing a received message, select
mode, your phone automatically downloads it
with a notification.
Options > Forward
2. Enter a number or address.
.
Note: If receiving a message during a call, the
phone downloads the message after the call.
3. Complete your message and select Send
.
44
Manage Received Messages
Reply to all Recipients
1. When viewing a received message, select
Options > Reply All to send your reply to
all the message recipients.
Lock Messages
When viewing a received message, select
Options > Lock Msg to protect it from
accidental deletion. To unlock the message,
select Options > Unlock Msg
.
2. Complete the message and select Send
.
Sort Messages in Inbox
1. From Inbox, select Options > Sort
Reply with a Copy of the Message
1. When viewing a received message, select
.
Options > Reply with Copy
.
2. Select a sort option.
The original message appears in your reply
message.
Go to Web Addresses in Messages
When viewing a received message, select
Options > Launch Browser to go to a web
address included in the message.
2. Complete your message and select Send
.
Call Sender
When viewing a received message, select
Options > Call to call the sender.
Manage Attached Files
Play Attached Files
Save Received Messages
When viewing a received message with files
attached, select Options > Play (to play an
attached file), Stop (to stop playing), or Mute
(to turn off the sound).
When viewing a received message, select
Options > Save Message to save it to Saved
Msgs
.
View Recipients
Save Attached Files
When viewing a received message, select
Options > Recipients to check all recipients of
the message.
When viewing a received message with files
attached, select the applicable save option to
save the attached files, including graphics,
sounds, contacts (vCard), or events (vCal). For
example, to save a contact, select Options >
View Sender Information
When viewing a received message, select
Options > Sender to view an existing contact,
add to an existing contact, or create a new
contact depending on the sender.
Save Contact
.
User Guide
45
When you have set up your voicemail, all
unanswered calls to your phone are
automatically transferred to voicemail, even if
your phone is in use or turned off.
1. Press and hold the 1 key.
View Messages with Multiple Slides
When viewing a received message containing
multiple slides, use the following options to
navigate through the slides.
•
•
Next to view the next slide.
Options > Replay to restart the message
from the beginning slide.
2. Follow the system prompts to create a
password and record a greeting.
•
•
•
Options > Pause to pause at the current
slide.
Options > Resume to resume playing the
slides.
Check your Voicemail
When you receive a voicemail message, a
notification with a voicemail message icon
appears at the top of your screen.
Options > Done to exit the message.
•
At the voicemail notification, select Call to
call your voicemail number and follow the
system prompts to retrieve the message.
Select Ignore to clear the notification
without checking messages. The
View Message Information
When viewing a received message, select
Options > Message Info to view the message
priority, sent time, size, etc.
notification icon remains on top of the
screen until you listen to the message.
When only the voicemail message icon
appears on top of the screen, select
Voicemail and follow the system prompts
to retrieve the message.
Replay Messages
When viewing a received message, select
Options > Replay to restart the message
(including a slide or sound if contained) from
the beginning.
•
Manage Voicemail
Configure your Voicemail
Before your phone can receive voicemail
messages, you need to set up a password and
record a personal greeting with your service
provider.
46
Manage Voicemail
Unable to Send Messages
Manage Sent Messages
You may not be able to send or receive
messages if your phone’s memory is nearly
full, or if digital service is not available at the
time. To free up memory, erase old messages.
Check Message Status in Sent Folder
Use the following symbols to check the Sent
folder for the status of messages successfully
sent.
Appended Messages
The scheduled message will be sent at
the scheduled time. You cannot cancel
delivery of the message.
If you go over the character limit for a single
message, the phone may automatically append
an empty segment to your message to make
space.
The message was sent. You cannot
cancel delivery of the message.
Warning: Your service provider may charge
you for each message segment.
The message has been received.
The message has been sent to more than
one recipient.
When you start a message, the maximum
character limit appears once you are in the
message entry field. This number counts down
as you enter characters, until it reaches 0.
If you continue to enter text after this counter
reaches 0, a message segment may be
appended. When you reach the message size
limit, you are prompted to edit the message or
alerted that the message is being appended.
Note: Appended messages may not be
available on all phones. Check with your
service provider.
Check Message Status in Outbox
Use the following symbols to check your
Outbox for the status of messages sent but still
in process.
The message is pending and will be sent
when possible. You can cancel delivery
of the message.
The message cannot be sent because
service is not available. An alert appears
on your phone if the message cannot be
sent.
Manage Browser Alerts
1. From Browser Alerts, select an alert.
2. Select Connect to launch the browser.
User Guide
47
Set Chat View
Message Settings
From Chat View, select Conversation to
group sent and received messages by contact,
phone number, or address. To view messages
in the order they are received or sent, select
The following message settings affect all
messages unless you change them for
individual messages.
Set Message Alerts
Classic
.
1. From Alerts, select Msg Alert
.
Set Message List View
From Msg List View, select one of the
following to set your message list display:
2. Select an alert for messages.
If you select an & Remind alert, the phone
notifies you once when receiving a new
message and notifies you again every five
minutes. To stop a reminder alert, select
•
•
•
•
Sender & Preview displays the sender and
first part of messages.
Sender & Date-Time displays the sender
and sent time of messages.
Msg Preview displays the first part of
messages.
Sender displays the message sender.
Ignore
.
Set Page Alerts
1. From Alerts, select Page Alert
2. Select an alert for pages.
.
If you select an & Remind alert, the phone
notifies you once when receiving a new
message and notifies you again every five
minutes. To stop a reminder alert, select
Set your Signature
You can create a signature to appear at the end
of all outgoing messages.
1. From Signature, enter your signature.
2. Select OK to save the signature.
Note: The signature counts towards the
character limit of your message.
Ignore
.
Set Voicemail Alerts
1. From Alerts, select Voicemail Alert
.
2. Select an alert for voicemails.
Edit Preset Messages
If you select an & Remind alert, the phone
notifies you once when receiving a new
message and notifies you again every five
minutes. To stop a reminder alert, select
Your phone comes with preset messages, such
as “Please call me,” which you can insert into
the body of a text message. You can edit or
create up to 40 preset messages.
Ignore
.
48
Message Settings
1. From QuickText, do one of the following:
Enable Save to Sent
From Save to Sent, select Enabled to
automatically save outgoing messages to the
Sent Msgs folder.
–
Scroll to a preset message and select
Edit
.
–
Select New Msg to create a new preset
message.
Enable Auto-Erase
2. Enter or edit the text.
3. Select Save
Note: You can also save messages you have
Use Auto-Erase to set your phone to erase
messages automatically when it needs memory
for incoming messages.
.
written or received as preset messages.
From Auto-Erase, select one of the following:
Enable Auto Retrieve
From Auto Retrieve, select one of the
following:
•
•
Disabled erases no messages.
Inbox Msgs erases old messages in Inbox
when memory is needed.
•
Disabled turns off auto retrieve and
prompts you before downloading any
multimedia messages.
Enabled turns on auto retrieve to
automatically download multimedia
messages.
•
•
Sent Msgs erases old messages in Sent
Msgs when memory is needed.
Both erases old messages in both Inbox
and Sent Msgs when memory is needed.
•
Set Default Text
You can change the default text entry mode
when creating a text message. This setting
applies only to the Message field, not the Send
To field.
From Default Text, select Normal Alpha (to
enter text letter by letter) or Rapid Entry (to
enter text with word recognition).
Enable CC/BCC Fields
From CC and BCC, select Disabled (to hide
the CC and BCC fields) or Enabled (to show
them).
Set Callback Number
1. From Callback Number, enter a new
number to change your default callback
number.
Request Text Message Receipts
From Text Msg Receipt, select Request to
request a notification when a recipient has
received your text message.
2. Select OK to save the number.
User Guide
49
Request Multimedia Message Receipts Erase Messages from a Folder
From Pic Msg Receipt, select Request to
request a notification when a recipient has
received your multimedia message.
From Erase Msgs, select a folder to erase
messages from. For example, to erase received
messages, select Inbox > Yes
.
Note: You cannot recover deleted information.
Set your Voicemail Number
Often your service provider automatically
programs your voicemail number (the number
your phone calls to retrieve voicemail). To
change it:
Erase All Messages
From Erase Msgs, select All > Yes to erase all
messages from all folders, except for voicemail
messages.
1. From Voicemail Number, select Edit
.
Note: You cannot recover deleted information.
2. Enter your voicemail number. (Use
Options > Time Pause or Hard Pause to
enter pauses.)
Check Message Count
From Message Count screen, check how
3. Select Save
.
many messages you have stored.
Erase Recent List
From Erase Recent List, select Yes to clear
the list of recipients you have recently sent
messages to.
Erase Messages
Erasing old messages frees up memory in your
phone. You can erase messages as you send or
read them, erase them one at a time, or erase
them all at once.
Erase a Single Message
When viewing a received message, select
Options > Erase > Yes
.
Note: You can erase a scheduled message, but
cannot cancel its delivery.
50
Erase Messages
10 Camera
Camera Tips
4. Select Send > Via EMS Msg (to attach to
an enhanced message), Via MMS Msg (to
attach to a multimedia message), Via
Bluetooth (to send to a Bluetooth-enabled
device), or To Printer (to print on a
Bluetooth-enabled device).
Select Erase to delete the picture from your
phone.
5. Press the End key to exit camera mode.
Note: If your phone has no Bluetooth feature,
you may send the file with a message only.
Your phone has a camera. Before using your
phone’s camera, here are some tips:
•
You cannot activate the camera while on an
active call or while browsing files in the
media gallery.
•
•
Once the camera is active, the home screen
acts as the viewfinder.
If you get a “Low memory” error, check
your resolution and quality compression
settings.
Other Camera Options
Camera Setting Options
Adjust the Resolution
From camera mode, select Options > Settings
> Resolution and a size for your pictures.
Numbers in the bottom left corner indicate the
current resolution setting.
•
If there is no activity within 30 seconds
after you turn your camera on, the camera
times out and returns to the previous launch
point.
Menu settings and options can only be
accessed when the camera is active.
Numbers in the top right corner indicate the
number of snapshots remaining before the
phone runs out of memory.
•
•
Set Self Timer
Take a Picture
From camera mode, select Options > Settings
> Self Timer and a time.
1. To activate the camera, press and hold the
Camera key. You can also select Camera
from the main menu.
The
icon indicates the timer is activated.
When you take a picture, a beep plays three
seconds from the time the shutter snaps the
picture.
2. Focus on the image using the phone’s
display as a viewfinder.
3. To take a picture, press the OK key. The
picture is saved to Camera Pictures
.
User Guide
51
Enable Date/Time Stamp
Set Color Tone
From camera mode, select Options > Settings
> Date/Time > On to place a date/time stamp
on each picture taken.
1. From camera mode, select Options >
Settings > Color Tone
.
2. Scroll left or right to select a color tone.
Look at the viewfinder to see how each
setting looks.
The
icon indicates when the date/time
stamp is on.
Enable Multishot Mode
Set Picture Quality
From camera mode, select Options > Settings
> Multishot > On to take multiple pictures.
From camera mode, select Options > Settings
> Picture Quality and a quality level for your
picture.
The
icon indicates multishot mode is
enabled. When you take a picture, press and
hold the OK key to take multiple pictures. A
single tone plays for each picture taken.
Your camera is set to a lower resolution during
multishot mode. The resolution setting returns
to the previous setting when you are done.
When you select a higher quality level, the size
of the file is bigger.
Set Brightness Level
1. From camera mode, select Options >
Brightness
.
2. Scroll left or right to change the brightness
level. Press the OK key to set the
brightness.
Set Shutter Sound
1. From camera mode, select Options >
Settings > Shutter Sound
2. Select a sound to play when the shutter
takes a picture.
.
Go to Camera Pictures
From camera mode, select Options > Camera
Pictures to see all of the pictures you have
taken. These are located in Camera Pictures
.
Set White Balance
1. From camera mode, select Options >
Take a Picture in a Frame
Settings > White Balance
.
1. From camera mode, select Options >
2. Scroll left or right to select the white
balance setting. Look at the display to see
how each setting looks.
Frames
.
2. Scroll left or right to view the frames
available.
3. Select OK to choose a frame.
4. Take a picture with the frame. The frame is
part of the image and can not be removed.
52
Other Camera Options
11 Scheduler
Use Scheduler to schedule events and set
reminder alerts.
Press the OK key to save and move to the
next field.
6. Press the OK key to select a priority from
the list.
Create an Event
7. Press the OK key to select a reminder from
the list.
1. From Add New Event, enter a name.
Scroll down to move to the next field when
done.
8. Press the OK key to select a reminder
sound from the list.
2. Press the OK key to select an event type
9. Press the OK key to select During Event
to enable silent mode or Off to have normal
sounds.
from the list.
3. Press the OK key to change the date, if
needed.
10. Press the OK key to select a recurring
–
Scroll left or right to move between
month, day, and year fields.
Scroll up or down to change month,
day, and year.
event from the list, if needed.
11. Select Save
.
–
View Events
View Events by Month
1. From View Month, scroll through the
month view. (Days with events are
highlighted.)
Press the OK key to save and move to the
next field.
4. Press the OK key to change the time, if
needed.
–
Scroll left or right to move between
hour, minute, and AM/PM fields.
Scroll up or down to change hour,
minute, and AM/PM.
–
2. Press the OK key to select a date.
3. Do one of the following:
Press the OK key to save and move to the
next field.
–
Scroll left or right to move to another
date.
5. Press the OK key to change the duration, if
–
–
Select an event.
Scroll to a time and select Add New to
create a new event.
needed.
–
Scroll left or right to move between
hour and minute fields.
Scroll up or down to change hour and
minute.
–
–
Select Options to access more features.
User Guide
53
View Events by Date
Sort Events by Priority
From View Day, do one of the following:
From View All Events, select Options > Sort
by Priority to sort events by their assigned
priority.
•
•
•
Scroll left or right to move to another date.
Select an event.
Scroll to a time and select Add New to
create a new event.
Modify Events
•
Select Options to access more features.
Edit an Event
Go to a Specific Date
1. From View Day, select an event.
2. At the event details screen, select Options
1. From Go to Date, scroll left or right to
move between month, day, and year fields.
Scroll up or down to change month, day, or
year.
> Edit
.
3. Modify the event and select Save
.
2. Press the OK key to select the date.
Send an Event
1. From View Day, select an event.
View Events by List
From View All Events, select an event from
the list or Options to access more features.
2. At the event details screen, select Options
> Send > Via MMS Msg (to attach the file
to a multimedia message), Via Bluetooth
(to send the file to a Bluetooth-enabled
device), or To Printer (to print the file on a
Bluetooth-enabled device).
Return to the Current Date
From View Day, select Options > Go to
Today to return to the current date.
3. Complete the appropriate task.
Sort Events by Time
Note: If your phone has no Bluetooth feature,
you may only send the file with a message.
From View All Events, select Options > Sort
by Time to sort events by time.
Copy an Event
1. From View Day, select an event.
2. At the event details screen, select Options
Sort Events by Type
From View All Events, select Options > Sort
by Type to sort events by their assigned type.
> Copy
.
3. Enter a new name for the event.
4. Complete the event and select Save
.
54
Modify Events
Erase Events
Erase an Event
1. From View Day, select an event.
2. At the event details screen, select Options
Change Scheduler Settings
From Settings, you can modify the following
features.
Set Scheduler Hours
1. From Scheduler Hours, modify the start
> Erase > Yes
.
and end times.
–
–
Scroll left or right to move between
hour, minute, and AM/PM fields.
Scroll up or down to change hour,
minute, and AM/PM.
Erase the Current Day’s Events
From View Day, select Options > Erase
Today’s Events > Yes to erase all events on
that day.
2. Select Save when done.
Erase All Events
From View All Events, select Options >
Erase All Events > Yes to erase all events
from the phone.
Erase Events Automatically
From Auto Erase, select an option from the
list to set when to automatically erase your past
events.
Note: You cannot recover deleted information.
Set Event Priority
From Priority, select an option to set every
Erase All Past Events
From View All Events, select Options >
Erase All Past Events > Yes to erase all past
events from the phone.
event you create with this priority type.
Set Event Reminder
From Reminder, select an option to set every
Note: You cannot recover deleted information.
event you create with this reminder setting.
Set Event Reminder Alert
From Reminder Sound, select an option to set
every event you create with this reminder alert.
(Scroll to listen to sounds.)
Set Event Silent Mode
From Silent Mode, select an option to set
every event you create with this silent mode.
User Guide
55
12 Settings
Settings Menu
Select Settings from the main menu to access the following functions:
Level 1 >
Settings
Level 2 >
Bluetooth
Browser
Level 3
Access these options: On/Off
Access these options: Multimedia
,
My Devices, and Settings
.
,
Look & Feel Security,
,
and Edit Search URL
.
Sounds
Display
Access these options: Ringers Ringer Mode, Volume, Pwr
,
On/Off Sound, and Keypad
.
Access these options: Set Wallpaper
,
Wallpaper Shuffle
Main Menu View My Banner
Language, and Time/Date
,
Set Screensaver
Backlighting Brightness
Format
,
Themes
,
,
,
,
,
.
Convenience
Access these options: Set Time/Date (with Airplane Mode
enabled), Airplane Mode Auto Keyguard Auto-Hyphen
1-Touch Dialing Answer Hold Fast Find Frequent List
Minute Alert Missed Call Alert Any Key Answer, and
Customize Keys
,
,
,
,
,
,
,
,
,
.
Voice Features
Access these options: Automatic Add
Display Results Digit Lengths Voice Answer, and Voice
Training
,
Expert Mode,
,
,
.
Accessories
Network
Access these options: Headset Sounds
,
Auto-Answer, Com
Port Speed TTY Device, and T-coil Hearing Aid
,
.
Access these options: Privacy Alert Voice Privacy,
,
Roam/Svc Alert
,
Roam Option
,
Set Phone Line
,
Location
,
Web Alert, and Roam Call Alert
.
Security
Access these options: Lock Phone
,
Limit Calls, and New
Lock Code
.
Phone Info
Access these options: Build Info
,
Icon Keys, and User
Guide
.
56
Settings Menu
Set Scroll Step
From Scroll Step, set how far up or down you
go when you scroll through Web page.
Bluetooth
Use Bluetooth to configure your devices. See
“Bluetooth” on page 74 for more information.
Set Connection Timeout
Browser
From Connection Timeout, set the amount of
time to wait for a browser connection to
initialize.
Use these settings to configure your browser.
Multimedia
From Multimedia, you can modify the
following settings.
Enable Browser Title
From Browser Title, turn the page titles on or
off when you use the browser.
Show Images
From Images, choose whether or not to show
images when you use the browser.
Set Launch Page
From Launch Page, set the Web page you go
to when you launch the browser.
Play Sounds
From Sounds, choose whether or not to play
sounds when you use the browser.
Enable Select Images
From Select Images, choose whether or not to
select images when you use the browser.
Download Objects
From Objects, choose whether or not to
download objects when you use the browser.
Security
From Security, you can modify the following
settings.
Look & Feel
From Look & Feel, you can modify the
following settings.
Enable Security Prompt
From Secure Prompt, turn the prompt that
appears when you enter a secure site on or off.
Set Font Size
From Font Size, choose the font size for the
browser.
Enable ID Cache
From ID Cache, turn the ID cache for the
browser on or off.
User Guide
57
– Edit Ringer Shuffle
1. From Ringer Shuffle, select Edit
Enable Cookies
From Cookies, turn the cookies for the
.
2. Select Add (to include the file in the
shuffle) or Remove (to remove the file
from the shuffle).
browser on or off.
Allow Link Referral
From Link Referral, choose whether or not to
allow link referrals when you use the browser.
3. When finished, select Options > Done
.
– View Ringer Shuffle
1. From Ringer Shuffle, select View. Only
the files used in your shuffle appear.
2. Select Edit to modify the shuffle list or
press the Back key to exit.
Edit Search URL
From Edit Search URL, modify the default
search page.
Sounds
Set Ringer Mode
Your phone has several settings that control the
sound. You can select from a variety of ringers
and adjust the volume.
Your phone is set to make sounds when you
receive calls, press keys, navigate through
menus, and receive alerts (such as new
messages). You can silence all sounds and set
the phone to vibrate or light up when you
receive calls and alerts.
Ringers
From Ringers, you can modify the following
settings.
From Ringer Mode, select one of the
following:
Set Ringers
From Ringer Type, select a ringer. (Scroll
down the list to play the ringers.)
•
Normal Sounds rings for the incoming call
or alert (in effect, returning the phone to a
non-silent mode).
Vibrate Only vibrates for the duration of
the incoming call or other alerts.
Vibe Then Ring vibrates for the first ten
seconds and then rings for the remainder of
the incoming call alert.
Enable Roam Ringer
From Roam Ringer, select Enabled to
activate a specific ringer for roaming calls.
•
•
Ringer Shuffle
– Enable Ringer Shuffle
From Ringer Shuffle, select Enable to turn on
the ringer shuffle.
•
Lights Only lights up for the duration of
the incoming call or other alerts.
58
Sounds
You can also press and hold the # Q key to
toggle between Vibrate Only mode and
Normal Sounds mode.
Set Power On/Off Sounds
1. From Pwr On/Off Sound, select Power
On Sound or Power Off Sound
.
Note: The phone rings when attached to an
external power source (such as a charger), even
if all sounds have been silenced.
2. Select a sound to play when your phone
powers on or off. (Scroll down the list to
play the sounds.)
Volume
Keypad
From Volume, you can modify the following
From Keypad, you can modify the following
settings.
settings.
Set Ringer Volume
1. From Ringer Volume, scroll right or left to
set the ringer volume.
Set Key Press Sounds
From Key Sounds, select Tone Click, or Off
to set the sounds you hear when pressing the
keypad.
,
2. Press the OK key to save.
Set Speakerphone Volume
Set Key Tone Length
1. From Speakerphone Volume, scroll right
or left to set the speakerphone volume.
2. Press the OK key to save.
From Key Length, select Normal or Long to
set the length of the keypad tone.
Display
Set Earpiece Volume
1. From Earpiece Volume, scroll right or left
to set the earpiece volume.
2. Press the OK key to save.
Set Wallpaper
You can select a wallpaper for your phone’s
home screen.
1. From Set Wallpaper, select Camera
Set Keypad Volume
1. From Key Volume, scroll right or left to set
the keypad volume.
Pictures
,
Saved Images, or Wallpapers.
To turn off wallpaper, select None
.
2. Select a file. You may need to resize or
crop the file.
2. Press the OK key to save.
3. Select Done
.
User Guide
59
Wallpaper Shuffle
Set Screensaver
Screensavers appear on the home screen,
activated ten seconds after the last keypress.
Incoming calls and alerts override the
screensavers.
Enable Wallpaper Shuffle
From Wallpaper Shuffle, select Enable to
turn on wallpaper shuffle.
1. From Set Screensaver, select Camera
Edit Wallpaper Shuffle
1. From Wallpaper Shuffle, select Edit
Pictures Saved Images, or Screensavers.
,
.
To turn off screensaver, select None
.
2. Select Add (to include a file in the shuffle)
or Remove (to remove a file from the
shuffle).
2. Select a file. You may need to resize or
crop the file.
3. Select Done
.
3. When finished, select Options > Done
.
Set Theme
From Themes, select a color theme for the
display background.
View Wallpaper Shuffle
1. From Wallpaper Shuffle, select View. The
files in your shuffle appear.
2. Select Edit to modify the shuffle list or
press the Back key to exit.
Set Main Menu View
From Main Menu View, select one of the
following:
•
Grid displays icons of each menu item,
with its name at the top of the screen.
List displays a list of all menu items.
Set Wallpaper Shuffle Interval
1. From Wallpaper Shuffle, select Set
•
Shuffle Time
.
The next time you view the Menu, your
selected menu style appears.
2. Select an interval time from the list. Your
wallpaper changes to another file in the
shuffle at the selected interval time.
Set Greeting Banner
The banner is the personal label for your
phone, appearing on the home screen above the
time and date.
1. From My Banner, select Edit
.
2. Press the Back key to clear the current
banner.
3. Enter your new text (up to 14 characters).
4. Select Save
.
60
Display
Backlighting
Convenience
Use these settings to make your phone more
convenient to use.
Set Display Duration
From Backlighting, select Display Duration
and one of the following:
Set Date and Time
•
•
Always Dim forces the backlight to remain
dim before turning off.
In Airplane mode, you can set the time and
date manually.
7 Seconds 10 Seconds, 15 Seconds, or 30
,
Note: You can only access Set Time/Date with
Airplane Mode enabled.
1. From Set Time/Date, do the following to
change the date:
Seconds turns backlighting on for the set
time after your last keypress.
•
Always Bright forces the backlight to
remain bright before turning off.
–
Scroll left or right to move between the
month, day, and year fields.
Scroll up or down to change the month,
day, and year.
Set Keypad Duration
From Backlighting, select Keypad Duration
and one of the following:
–
•
Off forces the backlight to remain dim
2. Press the OK key to save the date.
3. Do the following to change the time:
before turning off.
•
7 Seconds 10 Seconds, 15 Seconds, or 30
,
–
Scroll left or right to move between the
hour, minute, and AM/PM fields.
Scroll up or down to change the hour,
minute, and AM/PM.
Seconds turns backlighting on for the set
time after your last keypress.
–
•
Same as Display matches the setting for
the Display Duration
.
4. Press the OK key to save the time.
5. Select Done
Set Brightness
1. From Brightness, scroll to change the
.
brightness level.
Enable Airplane Mode
2. Select Save
.
While in an airplane, it is normally required
that you turn off your mobile phone because it
emits RF signals that interfere with air traffic
control. In airplane mode, however, your
phone does not emit RF signals. You cannot
make or receive calls, send text messages, use
the Browser or Bluetooth, but you can play
Set Language
From Language, select a language.
Set Time and Date Format
From Time/Date Format, select a time and
date format.
User Guide
61
games, use the Scheduler, set the clock, and
make emergency calls to designated
emergency numbers. Please check with
uniformed personnel before operating your
phone in Airplane mode.
Use 1-Touch Dialing
The 1-Touch Dialing feature is the fastest way
to call a speed dial location. To call a contact
with speed dial, press and hold the speed
dialing location.
From Airplane Mode, select Enabled > OK
to activate airplane mode.
With airplane mode enabled, you can also set
the time and date manually.
If it is a two-digit location, press the first digit
briefly, then press and hold the second digit.
Note: To use 1-Touch dialing, you must enable
1-Touch dialing on your phone and have a
speed dial location assigned to a contact.
From 1-Touch Dialing, select Enabled to turn
on 1-touch dialing.
Auto Keyguard
Enable Auto Keyguard
Use Auto Keyguard to automatically lock the
keypad after 30 seconds of inactivity to prevent
accidental key presses.
From Auto Keyguard, select Enabled or from
the home screen, press and hold the Back key.
Answer Hold
Enable Hold Call
Use Answer Hold to place incoming calls on
hold until you are ready to answer them.
1. From Answer Hold, select Enabled
.
Unlock Keyguard
From the home screen, select Unlock and press
the Back key to unlock the keypad.
If you have not recorded a hold message,
you need to record one, such as “Please
hold. I’ll answer in a minute.”
Enable Auto-Hyphenation
2. Record the message twice, as prompted.
3. Select Save or Options and one of the
following:
Auto-hyphenation, when enabled,
automatically inserts hyphens into your phone
numbers to be consistent with the U.S. dialing
plan (or the North American Numbering Plan).
From Auto-Hyphen, select Enabled to turn on
auto-hyphenation.
–
–
Play to replay your message.
Re-Record to record your message
again.
–
Exit to exit.
The next time a call comes in, you can place it
on hold.
62
Convenience
Place a Call on Hold
You can place a call on hold with Answer
Hold enabled.
Enable Frequent List
From Frequent List, select Enabled. With
Frequent List enabled, the last 15 of your
most frequently called contacts appear at the
beginning of your contacts list. Scroll past the
double line to view the entire contacts list.
Note: If you are already on a call and you
receive another call, you cannot place the
incoming call on hold. With no call waiting
enabled, the call goes to Voicemail
.
Enable Minute Alert
From Minute Alert, select Enabled. Your
phone alerts you with a short beep ten seconds
before each minute passes during a call.
When a call comes in, do the following:
1. Select Options > Answer Hold to place
the caller on hold with your recorded hold
message.
2. Select Answer to speak to the caller on
hold or End Call to hang up without
speaking.
Set Missed Call Alert
From Missed Call Alert, select an alert type
for missed calls.
Change Hold Call Message
If you select an & Remind alert, the phone
notifies you once when receiving a new
message and notifies you again every five
minutes. To stop a reminder alert, select
1. From Answer Hold, select Re-Record
Msg
.
2. Record the message twice, as prompted.
3. Select Save to save the message or Options
and one of the following:
Ignore
.
–
–
Play to replay your message.
Re-Record to record your message
again.
Enable Any Key Answer
From Any Key Answer, select Enabled to
answer calls when you press any key on the
keypad.
–
Exit to exit.
Call Contact using Fast Find
1. From Fast Find, select Enabled to turn on
fast find.
2. From the home screen, press the keys
corresponding to the letters of the name
you want to find. A matching contact or
speed dial entry appears.
Customize Keys
You can modify the Navigation key and Left
softkey settings to set up your desired shortcut.
1. From Customize Keys, select UP Key
LEFT Key RIGHT Key DOWN Key, or
Left Soft Key
,
,
,
.
3. Scroll to your desired contact and press the
2. Select your desired menu option for the
targeted key shortcut.
Send key to call the number.
User Guide
63
Create a Custom Menu
Set Display Results
1. From the home screen, scroll up and hold.
You can set the phone to display up to three
voice recognition contacts when calling or
searching for a contact with voice commands.
From Display Results, select Single Best or
2. Select Edit
.
3. Select features from the list provided. A
check mark appears next to each selection.
You can also remove checkmarks.
Three Best
.
4. Select Save after selecting all your options.
Your new selections appear the next time you
select your custom menu.
Set Digit Lengths
You can set the number of digits used for a
phone number in your voice dial list.
From Digit Lengths, select one of the
following options:
Voice Features
Use the following features to customize the
voice commands.
•
North American recognizes only 7, 10,
and 1 + 10 digits in a phone number.
Permit All allows 4-14 digits in a phone
number.
•
Enable Automatic Add
From Automatic Add, select Enabled to
automatically add a contact to your voice dial
list when you create a new contact.
Voice Answer
Enable Voice Answer
You can set your phone to answer a call with
your voice when using a hands-free accessory.
1. From Auto-Answer, select Disabled
2. From Ringer Mode, select Normal
Set Expert Mode
Use Expert Mode to speak a command after
you hear a tone instead of following the initial
voice prompts.
From Expert Mode, select one of the
following:
.
Sounds
3. From Headset Sounds, select Out of
Headset
4. From Voice Answer, select With
Accessory
.
•
Normal sets the phone to default voice
prompts.
.
•
Expert sets the phone to sound tones
instead of voice prompts.
.
64
Voice Features
Answer Using Voice Answer
Enable Auto-Answer
When you receive an incoming call, the phone
prompts “Incoming call, answer?” With the
caller recognized as a contact entry in your
phone, the phone prompts “Incoming call from
(Name), answer?” Do one of the following:
From Auto-Answer, select After 5 Seconds
The phone automatically answers after five
seconds with a headset attached.
.
Set Com Port Speed
From Com Port Speed, select a data rate at
which your phone connects to a laptop or PC.
Check with your service provider for details.
•
•
•
Say “Yes” or press any key except the End
key to answer the call.
Say “No” or press the End key to ignore
the call.
Remain silent. The voice alert repeats twice
and the phone rings once before returning
to the home screen.
Connect to TTY Device
You can connect the phone to a teletype (TTY)
device for the hearing impaired. (TTY device
sold separately.)
Note: Enable TTY only when using the phone
with a TTY device.
1. Connect the TTY device to your phone.
2. From TTY Device, select OK to clear the
notification.
Use Voice Training
If your phone has trouble recognizing your
voice, you can train your phone to recognize
your specific voice for numbers.
1. From Voice Training, read the message
and select OK > Train Numbers > OK
.
2. Follow the prompts for each number until
training is complete.
Note: You must read the numbers digit by digit
for voice training to work.
3. Select one of the following:
–
–
–
TTY Off disables TTY.
TTY On enables TTY devices.
TTY On + Talk enables TTY devices
and voice carry over.
Accessories
Set Headset Sounds
With a headset attached to your phone, you can
play the ringer through the headset or phone
speaker.
–
TTY On + Hear enables TTY devices
and hearing carry over.
Note: You can also enter ##889 with your
keypad and select TTY to enable TTY.
From Headset Sounds, select Out of Phone
(ringing from the phone speaker) or Out of
Headset (ringing from the headset).
User Guide
65
•
•
On Roam Change alerts you with two
decreasing tones when roaming service is
acquired and three increasing tones when
home area service is acquired again.
On Any Change alerts you with three
increasing tones if there is a change in
roaming service or three decreasing tones if
the phone loses service.
Connect to Hearing Aid Device
With a T-coil hearing aid device (sold
separately) connected, you can enable the
hearing aid feature.
1. Connect the T-coil hearing aid device to
your phone.
2. From T-coil Hearing Aid, select OK >
Enabled
.
Set Roaming Restrictions
You can restrict your phone from making a call
when roaming.
From Roam Option, select Automatic (to
allow roaming) or No Roaming (to disallow
roaming).
Network
Enable Privacy Alert
From Privacy Alert, select Enabled to set
your phone to alert you when enhanced digital
CDMA privacy is lost or regained.
Set Phone Line
Your phone can have two service accounts, or
phone lines, associated with it. Each phone line
has its own phone number.
Enable Voice Privacy
From Voice Privacy, select Enhanced to use
enhanced digital CDMA privacy.
Note: You must first establish a second phone
line with your service provider. Once
established, a second phone number becomes
available in the menu for selection.
Enable Roaming Service Alert
Use this setting if you want the phone to alert
you when you roam outside of your home
service area.
From Set Phone Line, read the note and select
OK and one of the phone lines.
From Roam/Svc Alert, select one of the
following:
When using one line, you cannot receive calls
from the other. It would be as if the phone were
“off” for that number. Your voicemail,
however, still takes messages. All contacts and
settings are shared for both lines.
•
•
Disabled turns roaming service alert off.
When No Svc alerts you with three tones
decreasing in pitch when service is lost and
three tones increasing in pitch when service
is acquired again.
66
Network
From Roam Call Alert, select Enabled
.
Set Location Information
The phone emits a distinctive ring to indicate
when you are roaming during a call. To accept
or place a call while roaming, you must press
Use Location to share your location
information with network services other than
emergency services (for example, 911, 111,
999 and 000) in serviced areas. This feature
works only when your phone is in digital
mode. You do have the option of turning off
the locator to emergency services.
1.
Security
This section describes the security features on
your phone. You can adjust these features to
prevent access to your personal information.
All security features are shielded by a
From Location, select one of the following:
•
911 Only (default) shares your position
information only with emergency services
when you call your 3-digit emergency
code.
four-digit lock code (typically 0000 or the last
4 digits of your phone number).
•
Location On shares your position
information, in addition to emergency
services.
Lock Phone
Set Lock Phone
With your phone locked, you can call only
emergency numbers or your service provider’s
customer service number. You can still receive
incoming calls.
1. From Security, enter your four-digit lock
code.
Set Web Alerts
You can set an alert to confirm the start or end
of a browser session.
From Web Alert, select one of the following:
•
•
•
At Start prompts when you start a session.
At End prompts when you end a session.
Both prompts when you start and end a
session.
2. Select Lock Phone > OK and one of the
following:
–
Lock Now locks the phone
immediately.
•
No Prompts sets for no prompts.
Enable Roaming Call Alert
–
On Power Up locks the phone every
time you turn it on.
You can set the phone to warn you before you
answer or place a call while roaming.
Note: Call prompt is disabled when the phone
is in Emergency Mode.
Unlock the Phone
1. From the home screen, select Unlock
.
2. Enter your four-digit lock code.
User Guide
67
Set Limit Calls
Access User Guide
From User Guide, access the user guide for
your phone.
You can limit the calls that can be made from
your phone to emergency numbers, your
contacts, and your service provider’s numbers.
1. From Security, enter your four-digit lock
code.
2. Select Limit Calls and one of the
following:
–
–
No Limit does not limit calls.
Limit Outgoing limits outgoing calls
while incoming calls still work.
Limit All limits both incoming and
outgoing calls.
–
Change Lock Code
Change your lock code from the default.
1. From Security, enter your four-digit lock
code.
2. Select New Lock Code > Yes
3. Enter a new four-digit code.
4. Re-enter your new lock code.
.
Phone Info
View Version Information
Select Build Info to check your phone’s
software and hardware information.
View Phone Icons
Select Icon Keys to view the icons used in
your phone.
68
Phone Info
13 Downloads
2. Select an application type. A list of
applications appears. Long titles scroll left
as you highlight them.
3. Select an application. A list of usages
appears. There may be one or more usages
available. Prices are specified for each
usage.
4. Select a usage for the application. You are
prompted to confirm your purchase.
5. Select Yes to confirm. The application
downloads to your phone. Download times
may vary.
To open the application now, select Yes. If you
select No, you return to Downloads, where
you see a link to your new application.
Note: Your connection to the application
server automatically ends after 30 seconds,
unless you connect again to download more
apps. If you want to end the connection
manually, press the End key on your phone.
How does BREW Work?
Your Kyocera phone has the added ability to
download and manage applications through
BREW.
You connect to the server, download
applications, and then manage them as you
like. When you choose an application, you
have the option of choosing a demo, various
limited use options, or the full version—all
varying in price. If you choose a demo, BREW
lets you know when it has expired. If you
choose a priced version, the amount is added to
your phone bill. BREW also lets you know if
you are running out of memory. At that point,
you can either disable an application or remove
it completely.
Once applications are loaded, you can update
to newer versions as they become available.
For more information about BREW
capabilities and application pricing, contact
your service provider.
Access Help for Downloads
From Downloads, select Help to get
instructions on how to run and manage your
downloaded applications.
Download an Application
1. From Downloads, select Mobileshop >
Catalog. When a connection is made, a list
of application types appears.
User Guide
69
14 Tools & Games
Tools & Games Menu
Select Tools & Games from the main menu to access the following functions:
Level 1 >
Level 2 >
Level 3
Tools & Games
Brick Attack
Voice Memo
Scheduler
Play Brick Attack.
Access these options: Record New and Recorded Memos
Schedule an appointment.
Set an alarm.
.
Alarm Clock
Tip Calculator
Calculator
Timer
Calculate a tip.
Perform basic calculations.
Set a countdown timer.
Use a stopwatch timer.
Stopwatch
Memopad
World Clock
Access these options: New Memo and View Memos
.
View times from different time zones.
70
Tools & Games Menu
Play Brick Attack
Scheduler
The goal of this game is to eliminate bricks
arranged in levels. You send a moving ball
upward using a paddle at the bottom of the
screen.
Use Scheduler to schedule appointments and
information.
1. Select Brick Attack
2. You may see a notification, select Yes or
No
.
Alarm Clock
.
Clock” on page 33 for more information.
3. Select New to start the game. You have the
following options:
–
Use the Navigation key to move the
paddle.
Use Tip Calculator
1. From Tip Calculator, enter the amount of
your bill.
–
–
–
Press the Back key to pause the game.
Select Resume to restart the game.
2. Select the percentage you want to tip.
3. Enter the number of people sharing the bill
(or enter 1 if paying the entire bill).
4. Select Next to view the final bill.
5. Select Done when finished.
Select Options
>
Exit to exit the game.
Voice Memo
Use Voice Memo to record and play back
audio memos.
Record Voice Memos
Use Calculator
1. From Voice Memo, select Record New
2. Record your voice memo and select Stop
when done.
.
1. From Calculator, enter the first number.
2. Select a mathematical operation:
3. Select Save
.
–
–
–
–
Scroll left to multiply.
Scroll right to divide.
Scroll up to add.
If you receive an incoming call while recording
a memo, the memo is saved and the incoming
call screen appears.
Scroll down to subtract.
Your selection will appear highlighted.
3. Enter the second number, and press the OK
key to view the result.
Play Voice Memos
1. From Recorded Memos, highlight a
memo.
2. Select Play to play the memo or Options to
access more features.
User Guide
71
4. Select Exit to return to the menu, or
Use Stopwatch
Options and one of the following:
From Stopwatch, select from the following
–
MS replaces the value currently stored
in memory with the displayed result on
the screen.
options:
•
•
•
Start begins counting.
Stop pauses counting.
Reset clears the stopwatch.
–
–
–
M+ adds displayed result on the screen
to the value currently stored in memory.
MR displays value currently stored in
memory on the screen.
MC clears value currently stored in
memory.
Press the Back key to exit.
Memopad
Write a Memo
1. From New Memo, enter the memo.
Use Timer
2. Select Save
.
The timer counts down for the specified time.
It beeps when that amount of time has elapsed.
View a Memo
From View Memos, select View to open a
memo or Options to access more features.
1. From Timer, select Set
.
2. Enter the time length.
–
Scroll left or right to move between
hours, minutes, or seconds fields.
Scroll up or down to change hours,
minutes, or seconds.
Edit a Memo
1. From View Memos, highlight a memo.
–
2. Select Options > Edit
3. Edit the memo, and select Save
.
.
3. Select Sound, and choose from the list to
modify the sound.
4. To work the timer, select from the
following options:
Send a Memo
1. From View Memos, highlight a memo.
2. Select Options > Send as SMS
3. Complete the message, and select Send
.
–
–
–
Start begins the countdown.
Stop pauses the countdown.
Reset clears the timer.
.
When the countdown is complete, select Off to
silence the alarm.
72
Use Timer
Call a Number in a Memo
If you have a phone number in a memo, you
can call it.
World Clock
Use World Clock to check times in cities
around the world in relation to your local time.
1. From View Memos, highlight a memo.
Set World Clock
1. From World Clock, first scroll left or right
to select a time zone.
2. Select Options > Use Numbers
.
3. Select a number, and press the Send key.
Lock a Memo
You can lock a memo to prevent it from being
edited or erased.
2. Check your local time and date on the first
line, followed by your selected world city
and its time and date.
1. From View Memos, highlight a memo.
Search World Clock
2. Select Options > Lock Memo
.
1. From World Clock, select Options >
To unlock a memo, select Unlock Memo
.
Search City or Search Country
.
2. Enter the first letter(s) of your desired city
or country.
3. Select a city or country from the list.
Erase a Memo
1. From View Memos, highlight a memo.
2. Select Options > Erase > Yes
.
Erase All Memos
From View Memos, select Options > Erase
All > Yes
.
Note: Selecting Erase All only erases
unlocked memos.
User Guide
73
15 Bluetooth
The Bluetooth® wireless technology (not
available on all phones) enables wireless
connectivity with accessories such as portable
or installed hands-free car kits, phones,
handsets, computers, and so on. For details,
check with your service provider.
2. From My Devices, select Find New. Your
phone then searches and detects any
available Bluetooth devices in the vicinity.
You must enable the Bluetooth feature on
your phone.
3. At the device list, highlight a device and
You must use a Bluetooth device (compatible
with Class 2 Bluetooth wireless technology,
version 1.2) in order to use this phone
wirelessly. Bluetooth accessories display a
symbol on your phone.
select Add
Accept the pairing if prompted.
4. If necessary, enter the password provided
with the Bluetooth device and select OK
With the password accepted, the device
appears in your device list.
.
.
Enable Bluetooth
Before you can connect your phone with a
Bluetooth device, you need to enable the
Bluetooth feature on your phone.
Use Bluetooth Devices
Connect to a Device
Before you can use Bluetooth, you must get
your phone ready to communicate with a
device. This is called “connecting.”
From On/Off, select On
.
Pair with a Device
To connect your phone to a Bluetooth device,
from My Devices, highlight a device and select
To enable your phone to communicate with a
Bluetooth device, you need to "pair" the device
with your phone. The following instructions
describe the process. You may also need to
reference the user guide provided with your
Bluetooth device.
Connect
.
A notification appears confirming the
connection. You can now use the device with
your phone.
1. Prepare the Bluetooth device (accessory)
for pairing as described in the device’s user
guide.
Disconnect from a Device
From My Devices, highlight a connected
device and select Disconnect
.
74
Enable Bluetooth
Rename a Device
Limit Visibility
1. From My Devices, highlight a device.
By default your phone is always visible, if set
to visible mode. You can limit the time your
phone is visible to other Bluetooth devices.
From Visibility, select an option to set the
phone visible for your selected time before
becoming invisible.
2. Select Options > Rename
3. Enter a new name and select Save
.
.
Delete a Device
You can delete a Bluetooth device that you
have paired your phone with.
1. From My Devices, highlight a device.
2. Select Options > Delete > Yes
View Supported Services
Select Services to view a list of the Bluetooth
service profiles your phone supports.
.
View Device Services
Enable OBEX Authentication
A Bluetooth device paired with your phone
may have more than one service profile (such
as Headset, Handsfree, and so on). Do the
following to check the services available:
1. From My Devices, highlight a device.
From OBEX Authentication, select Enabled
With object exchange (OBEX) authentication
enabled, you need a user name and password to
transfer files via Bluetooth.
.
2. Select Options > Services
.
3. At the service list, highlight a profile and
select Connect to change the active profile.
Change Bluetooth Settings
From Settings, you can modify the following
Bluetooth features.
Change Phone’s Name
You can change the name presented for other
Bluetooth devices’ search of your phone.
From My Name, enter a new name and select
Save
.
User Guide
75
16 Voice Commands
You can execute certain commands through
voice recognition. To control the settings
Call a Number
1. From the home screen, press and hold the
Send key. The phone prompts, “Say a
command”.
2. Say “Dial Number” and then speak the
digits of the number you want to call. If you
pause, the phone prompts you, “Did you
say <number>” or “Say a number” if it
does not recognize the name. Say “Yes” to
make the call, “No” to cancel the phone
call.
Call a Contact
1. From the home screen, press and hold the
Send key. The phone prompts, “Say a
command”.
2. Say “Contact” and the name of the person
you want to call.
The phone prompts, “Please repeat” or
“Say a name” if it does not recognize the
name. If the name you spoke matches a
contact in the voice dial list, the phone
prompts: “Name, correct?” Say “Yes” to
make the call, “No” to select a similar
name, or “Cancel” to cancel the phone call.
If the phone finds multiple voice tags that
sound like the name you said, the phone
will list the names. You will be asked to
verify which name you want to call. Say
“Yes” when you hear the correct name. Say
“No” when you hear an incorrect name.
3. Press the End key to end the call.
To modify your voice dial list, see “Enable
Voice Dial Tags” on page 28.
3. Press the End key to end the call.
Use a Shortcut
1. From the home screen, press and hold the
Send key. The phone prompts, “Say a
command”.
2. Say the name of the menu item you want to
access or say “Shortcuts” to view a list of
menu items. The phone prompts, “Say one
of the shortcuts”.
3. Say the name of the menu item you want to
access.
76
Call a Contact
Find a Contact
1. From the home screen, press and hold the
Send key. The phone prompts, “Say a
command”.
2. Say “Find Contact”. The phone prompts,
“Say a name”.
The phone prompts, “Please repeat” or “Say a
name” if it does not recognize the name. If the
name you spoke matches a contact in the voice
dial list, the phone prompts: “Name, correct?”
Say “Yes” to display the contact, “No” to select
a similar name, or “Cancel” to cancel the
search.
Note: You can only search for contacts that are
in the voice dial list.
User Guide
77
17 Get Help
User Guide
Before requesting support, please try to
reproduce and isolate the problem. When you
contact the Customer Care Center, be ready to
provide the following information:
From Phone Info, select User Guide to access
the user guide for your phone. You can also
find the user guide at
•
•
The name of your service provider.
The actual error message or problem you
are experiencing.
.
Customer Support
•
•
The steps you took to reproduce the
problem.
The phone’s mobile equipment identifier
(MEID).
Your service provider’s customer support
department may be accessible directly from
your phone when you dial a number, such as
*611 (check with your service provider). They
can answer questions about your phone, phone
bill, call coverage area, and specific features
available to you, such as call forwarding or
voicemail. For questions about the phone
features, refer to the materials provided with
your phone, or visit
Note: From Phone Info, select Build Info
.
Scroll down to MEID. The 18-digit number is
the MEID number. If your phone uses an
electronic service number (ESN), ESN
replaces MEID
.
Qualified Service
.
If the problem with your phone persists, return
the phone with all accessories and packaging to
the dealer for qualified service.
For additional questions, you may contact the
Kyocera Communications Inc. Customer Care
Center in any of the following ways:
•
•
•
Phone Accessories
Email: [email protected].
Phone (U. S. and Canada): 1-800-349-4478
or 1-858-882-2000 (press 2 for Product
Information).
To shop for phone accessories, visit
kyocera.superiorcommunications.com
.
78
User Guide
C
call lists
call timers
calls
80
H
headsets
hold calls
D
I
images
E
K
F
keyguard
keypad
G
games
groups
L
M
media files
User Guide
81
menus
messages
82
pictures
N
notifications
Q
O
R
ringer shuffle
ringers
P
pages
roaming
phone
S
User Guide
83
T
settings
U
sounds
V
speed dial list
voice dial list
84
voicemail
volume
W
wallpaper shuffle
User Guide
85
|