Your wireless phone is a radio transmitter and
receiver. It is designed and manufactured to not
exceed the emission limits for exposure to radio
frequency (RF) energy set by the Federal
Communications Commission of the U.S.
Government. These limits are part of
Body-worn measurements differ among phone
models, depending upon availability of accessories
and FCC requirements. While there may be
differences between the SAR levels of various
phones and at various positions, they all meet the
government requirement for safe exposure.
comprehensive guidelines and establish permitted
levels of RF energy for the general population. The
guidelines are based on standards that were
developed by independent scientific organizations
through periodic and thorough evaluation of
scientific studies. The standards include a
substantial safety margin designed to assure the
safety of all persons, regardless of age and health.
The exposure standard for wireless mobile phones
employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set
by the FCC is 1.6 W/kg.*
The FCC has granted an Equipment Authorization
for this model phone with all reported SAR levels
evaluated as in compliance with the FCC RF
emission guidelines. SAR information on this model
phone is on file with the FCC and can be found
under the Display Grant section
http://www.fcc.gov/oet/ea/ after searching on the
FCC ID: OVFKWC-M1000-2X0.
Additional information on SAR can be found on the
Cellular Telecommunications and Internet
Association (CTIA) web-site at
Tests for SAR are conducted using standard
operating positions specified by the FCC with the
phone transmitting at its highest certified power
level in all tested frequency bands.
* In the United States and Canada, the SAR limit for
mobile phones used by the public is 1.6 watts/kg
(W/kg) averaged over one gram of tissue. The
standard incorporates a substantial margin of
safety to give additional protection for the public
and to account for any variations in measurements.
Although the SAR is determined at the highest
certified power level, the actual SAR level of the
phone while operating can be well below the
maximum value. This is because the phone is
designed to operate at multiple power levels so as
to use only the power required to reach the network.
In general, the closer you are to a wireless base
station antenna, the lower the power output.
Caution
The user is cautioned that changes or modifications
not expressly approved by the party responsible for
compliance could void the warranty and user’s
authority to operate the equipment.
Optimize your phone’s performance
Before a phone model is available for sale to the
public, it must be tested and certified by the FCC
that it does not exceed the limit established by the
government-adopted requirement for safe
exposure. The tests are performed in positions and
locations (e.g., at the ear and worn on the body) as
required by the FCC for each model.
Use the guidelines in this guide to learn how to
optimize the performance and life of your phone
and battery.
Air bags
If you have an air bag, DO NOT place installed or
portable phone equipment or other objects over the
air bag or in the air bag deployment area. If
equipment is not properly installed, you and your
passengers risk serious injury.
User Guide
iii
Vehicles—RF signals may affect improperly
installed or inadequately shielded electronic
systems in motor vehicles. Check with the
manufacturer of the device to determine if it is
adequately shielded from external RF energy.
Medical devices
Pacemakers—Warning to pacemaker wearers:
Wireless phones, when in the ‘on’ position, have
been shown to interfere with pacemakers. The
phone should be kept at least six (6) inches away
from the pacemaker to reduce risk.
Blasting areas—Turn off your phone where
blasting is in progress. Observe restrictions, and
follow any regulations or rules.
The Health Industry Manufacturers Association and
the wireless technology research community
recommend that you follow these guidelines to
minimize the potential for interference.
Potentially explosive atmospheres—Turn off your
phone when you are in any area with a potentially
explosive atmosphere. Obey all signs and
instructions. Sparks in such areas could cause an
explosion or fire, resulting in bodily injury or death.
Areas with a potentially explosive atmosphere are
often, but not always, clearly marked.
•
Always keep the phone at least six inches
(15 centimeters) away from your pacemaker
when the phone is turned on.
•
•
•
Do not carry your phone near your heart.
Use the ear opposite the pacemaker.
If you have any reason to suspect that
interference is taking place, turn off your
phone immediately.
They include:
•
•
•
•
fueling areas such as gas stations
below deck on boats
Hearing aids—Some digital wireless phones may
interfere with hearing aids. In the event of such
interference, you may want to consult your service
provider or call the customer service line to
discuss alternatives.
transfer or storage facilities for fuel or chemicals
vehicles using liquefied petroleum gas, such as
propane or butane
•
•
areas where the air contains chemicals or
particles such as grain, dust, or metal powders
Other medical devices—If you use any other
personal medical device, consult the manufacturer
of the device to determine if it is adequately
shielded from external RF energy. Your physician
may be able to help you obtain this information.
any other area where you would normally be
advised to turn off your vehicle engine
Use with care
Use only in normal position (to ear). Avoid dropping,
hitting, bending, or sitting on the phone.
In health care facilities—Turn your phone off in
health care facilities when instructed. Hospitals and
health care facilities may be using equipment that is
sensitive to external RF energy.
Keep phone dry
Keep the phone dry. Damage can result if the
phone gets wet. Water damage is not covered
under warranty.
Potentially unsafe areas
Posted facilities—Turn your phone off in any
facility when posted notices require you to do so.
Aircraft—FCC regulations prohibit using your
phone on a plane that is in the air. Turn your
phone off or switch it to Airplane Mode before
boarding aircraft.
iv
Resetting the phone
E911 mandates
If the screen seems frozen and the keypad does not
respond to keypresses, reset the phone by
completing the following steps:
Where service is available, this handset complies
with the Phase I and Phase II E911 Mandates
issued by the FCC.
1. Remove the battery door.
Hearing Aid Compatibility (HAC)
2. Remove and replace the battery.
Some mobile phones and hearing devices (hearing
aids and cochlear implants), when used together,
result in buzzing, humming, or whining noises
detected by the user. Some hearing devices are
more immune than others to this interference noise,
and phones also vary in the amount of interference
they generate.
If the problem persists, return the phone to the
dealer for service.
Accessories
Use only Kyocera-approved accessories with
Kyocera phones. Use of any unauthorized
accessories may be dangerous and will invalidate
the phone warranty if said accessories cause
damage or a defect to the phone.
The wireless telephone industry has developed
ratings for some of their mobile phones, to assist
hearing device users in finding phones that may be
compatible with their hearing devices. Not all
phones have been rated. Phones that are rated
have the rating on their box or a label on the box.
The ratings are not guarantees and results will vary
depending on the user’s hearing device and
hearing loss. If your hearing device happens to be
vulnerable to interference, you may not be able to
use a rated phone successfully. Trying out the
phone with your hearing device is the best way to
evaluate it for your personal needs.
Radio Frequency (RF) energy
Your telephone is a radio transmitter and receiver.
When it is on, it receives and sends out RF energy.
Your service provider’s network controls the power
of the RF signal. This power level can range from
0.006 to 0.6 watts.
In August 1996, the U.S. Federal Communications
Commission (FCC) adopted RF exposure
guidelines with safety levels for hand-held wireless
phones. These guidelines are consistent with the
safety standards previously set by both U.S.
and international standards bodies in the
following reports:
M-Ratings—Phones rated M3 or M4 meet FCC
requirements and are likely to generate less
interference to hearing devices than phones that
are not labeled. M4 is the better/higher of the
two ratings.
•
•
•
ANSI C95.1 (American National Standards
Institute, 1992)
T-Ratings—Phones rated T3 or T4 meet FCC
requirements and are likely to be more usable with a
hearing device’s telecoil (“T Switch” or “Telephone
Switch”) than unrated phones. T4 is the better/higher
of the two ratings. (Note that not all hearing devices
have telecoils in them.)
NCRP Report 86 (National Council on
Radiation Protection and Measurements, 1986)
ICNIRP (International Commission on Non-
Ionizing Radiation Protection, 1996)
Your phone complies with the standards set by
these reports and the FCC guidelines.
User Guide
v
Hearing devices may also be measured for
immunity to this type of interference. Your hearing
device manufacturer or hearing health professional
may help you choose the proper rating for your
mobile phone. The more immune your hearing aid
is, the less likely you are to experience interference
noise from mobile phones.
For more information about hearing aid
compatibility, visit the FCC's Consumer &
Governmental Affairs Bureau Web site at
Battery and charger specifications
Charger
Input
Output
CE90-R2233
CV90-G2926
CV90-K0281
100-240 VAC / 50/60 Hz 5V 350mA
100-240 VAC / 50/60 Hz 4.5V 1.2A
100-240 VAC / 50/60 Hz 4.5V 600mA
Standard Battery (5mm):
CV90-N3344 3.7V / 900 mAh
Kyocera Wireless Corp.
10300 Campus Point Drive
San Diego, CA 92121 USA
To purchase accessories, visit
vi
TABLE OF CONTENTS
Disabling an application . . . . . . . . . . . . . . . . . . 24
Checking available memory . . . . . . . . . . . . . . . . 24
1
Getting started . . . . . . . . . . . . . . . . . . . . . . 1
Phone battery. . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Phone overview . . . . . . . . . . . . . . . . . . . . . . . . . .3
Main menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Basic navigation . . . . . . . . . . . . . . . . . . . . . . . . .11
Guide conventions . . . . . . . . . . . . . . . . . . . . . . .11
6
Web Browser . . . . . . . . . . . . . . . . . . . . . .25
Launching Web Browser . . . . . . . . . . . . . . . . . . 25
Using Web menu options . . . . . . . . . . . . . . . . . . 25
Searching for Web site . . . . . . . . . . . . . . . . . . . . 26
Using bookmark . . . . . . . . . . . . . . . . . . . . . . . . 26
Checking Browser Alerts . . . . . . . . . . . . . . . . . . 26
Web Alert. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2
Basic functions . . . . . . . . . . . . . . . . . . . . 12
Powering up. . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Making phone calls . . . . . . . . . . . . . . . . . . . . . .12
Answering phone calls . . . . . . . . . . . . . . . . . . . .12
Ending phone calls. . . . . . . . . . . . . . . . . . . . . . .13
Verifying your phone number. . . . . . . . . . . . . . .13
Activating voice dialing. . . . . . . . . . . . . . . . . . . .13
Taking a picture. . . . . . . . . . . . . . . . . . . . . . . . .13
Using custom menu . . . . . . . . . . . . . . . . . . . . . .13
7
8
Recent Calls . . . . . . . . . . . . . . . . . . . . . . . 27
Call lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Call timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Viewing contacts list. . . . . . . . . . . . . . . . . . . . . . 29
Adding contacts . . . . . . . . . . . . . . . . . . . . . . . . . 29
Working with contacts . . . . . . . . . . . . . . . . . . . . 30
Searching contacts. . . . . . . . . . . . . . . . . . . . . . . 33
3
Call features . . . . . . . . . . . . . . . . . . . . . . . 14
Volume control . . . . . . . . . . . . . . . . . . . . . . . . .14
Hold Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Speed dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
1-Touch Dialing . . . . . . . . . . . . . . . . . . . . . . . . .14
Voicemail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Data and fax calls. . . . . . . . . . . . . . . . . . . . . . . .15
Roaming calls . . . . . . . . . . . . . . . . . . . . . . . . . .15
Emergency services . . . . . . . . . . . . . . . . . . . . . .16
Airplane Mode . . . . . . . . . . . . . . . . . . . . . . . . . .16
9
Messages . . . . . . . . . . . . . . . . . . . . . . . . .34
Text messages . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Multimedia messages. . . . . . . . . . . . . . . . . . . . . 36
Erasing messages. . . . . . . . . . . . . . . . . . . . . . . . 38
Working with messages . . . . . . . . . . . . . . . . . . . 39
Creating group lists . . . . . . . . . . . . . . . . . . . . . . 40
Message settings . . . . . . . . . . . . . . . . . . . . . . . . 41
10 Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Taking a picture. . . . . . . . . . . . . . . . . . . . . . . . . 44
Camera mode options . . . . . . . . . . . . . . . . . . . . 44
Camera indicators and icons . . . . . . . . . . . . . . . 45
4
5
Text entry . . . . . . . . . . . . . . . . . . . . . . . . . 17
QWERTY keypad . . . . . . . . . . . . . . . . . . . . . . . .17
Number keypad . . . . . . . . . . . . . . . . . . . . . . . . .20
BREW Apps . . . . . . . . . . . . . . . . . . . . . . . 23
Using BREW Apps. . . . . . . . . . . . . . . . . . . . . . . .23
Downloading an application. . . . . . . . . . . . . . . .23
Opening an application . . . . . . . . . . . . . . . . . . .24
Viewing application details. . . . . . . . . . . . . . . . .24
Removing an application . . . . . . . . . . . . . . . . . .24
11 Media Gallery . . . . . . . . . . . . . . . . . . . . . .46
Accessing folders . . . . . . . . . . . . . . . . . . . . . . . . 46
Browsing camera pictures . . . . . . . . . . . . . . . . . 46
Browsing images . . . . . . . . . . . . . . . . . . . . . . . . 47
Browsing sounds . . . . . . . . . . . . . . . . . . . . . . . . 47
Playback tools . . . . . . . . . . . . . . . . . . . . . . . . . . 47
User Guide
vii
12 Tools & Games. . . . . . . . . . . . . . . . . . . . . 48
Brick Attack . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Race 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Voice Memo . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Scheduler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Alarm Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Tip Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Stopwatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Flashlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13 Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Menu options . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
My Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
14 Bluetooth® Wireless Technology . . . . . . 67
Turning Bluetooth on . . . . . . . . . . . . . . . . . . . . 67
Pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Using Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . 68
Bluetooth settings . . . . . . . . . . . . . . . . . . . . . . . 68
15 Voice recognition. . . . . . . . . . . . . . . . . . . 69
Voice dial list . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Voice commands. . . . . . . . . . . . . . . . . . . . . . . . 69
Voice Command Settings. . . . . . . . . . . . . . . . . . 70
16 Getting Help . . . . . . . . . . . . . . . . . . . . . . . 71
Customer Support. . . . . . . . . . . . . . . . . . . . . . . 71
Qualified service . . . . . . . . . . . . . . . . . . . . . . . . 71
Phone accessories. . . . . . . . . . . . . . . . . . . . . . . 72
Product evaluation . . . . . . . . . . . . . . . . . . . . . . 72
17 Consumer Limited Warranty. . . . . . . . . . 73
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
viii
1
GETTING STARTED
7. Set the screw slot in
horizontal position to
lock the back cover.
Note: To remove the battery,
make sure the phone is
powered off.
Phone battery
Installing the battery
To install the battery:
1. Hold the phone
face down and locate
the screw on the
Charging the battery
back cover.
You must have at least a partial charge in the
battery to make or receive calls.
To charge the battery:
1. Connect the AC adapter
to the jack on the bottom
of the phone. Do not
force the AC adapter into
the jack.
2. Plug the adapter into a
wall outlet.
The battery icon in the upper-right corner of the
screen tells you whether the phone is:
2. Turn the screw to set
the screw slot in
vertical position to
unlock the back cover.
3. Locate the groove on
the left side of the
phone and unsnap the
hooks to remove the
back cover.
4. Place the battery in the
phone casing with the
metal contacts of the
battery touching those
of the phone.
•
•
•
Charging (animated icon)
Partially charged
Fully charged
5. Replace the back
cover by sliding the
notches into the
Warning: The battery does not charge if you use
the phone while it is connected to an AC adapter.
opening on the
Recharging the battery
You can safely recharge the battery at any time,
even if it has a partial charge.
left side.
6. Snap the back panel
into place.
User Guide
1
•
•
Replace the battery only with another qualified
battery. Use of an unqualified battery may
present a risk of fire, explosion, leakage, or
other hazard. If you are unsure about whether
a replacement battery is compatible, contact
customer support.
Promptly dispose of used batteries in
accordance with local regulations and
recycle if possible. Do not dispose as
household waste.
Supervise all battery usage by children.
Avoid dropping the phone or battery. If the
phone or battery is dropped, especially on a
hard surface, an internal short-circuit can
occur and pose a safety hazard. If you
suspect battery damage, take it to a service
center for inspection.
Battery care
General safety guidelines
•
•
Do not disassemble or open the battery.
Do not crush, bend, deform, puncture, or
shred the battery.
•
•
Do not attempt to insert foreign objects into
the battery.
Do not immerse the battery or expose it to
water or other liquids. Even if a battery
appears to dry out and operate normally,
internal parts can slowly corrode and pose a
safety hazard.
•
•
•
Always keep the battery between 15°C and
25°C (59°F and 77°F). Do not expose the
battery to extremes of temperature, fire, or
other hazards such as a cooking surface, iron,
or radiator.
•
Improper battery use may result in fire,
explosion, or other hazard.
•
•
•
Never use any damaged battery.
Only use the battery for its intended phone.
Only use the battery with a qualified charger.
Use of an unqualified battery charger may
present a risk of fire, explosion, leakage, or
other hazard. If you are unsure about
whether a charger is qualified, contact
customer support.
Common causes of battery drain
•
•
•
•
Playing games or using the Web.
Taking pictures with the flash on.
Keeping backlighting on.
Operating in digital mode when far away from
a base station or cell site.
Using data cables or accessories.
Operating when no service is available, or
service is available intermittently.
High earpiece and ringer volume settings.
Repeating sound, vibration, or lighted alerts.
Extensive use of flashlight option.
•
•
•
Do not short-circuit the battery or allow
metallic conductive objects—such as
keys, coins, or jewelry—to contact the
battery’s terminals.
•
•
•
2
Phone battery
Phone overview
Getting to know your phone
The phone has two keypads—the number keypad and the QWERTY keypad.
Number keypad
1. External screen.
2. External Camera key activates camera mode.
3. Volume key to raise or lower speaker volume.
4. Navigation key scrolls through lists and text entry
fields and accesses shortcuts from the home screen.
5. Left softkey accesses menus and functions.
6. Speakerphone key activates the speakerphone and
answers incoming calls.
7. Send/Talk key starts or answers a call. Press once to
activate voice command, twice to display the All Calls
list, and three times to redial the last number dialed.
Press and hold to access voice dial.
8. External number keypad for entering numbers, letters,
or symbols.
9. * Shift key changes the text mode in text entry.
10. Jack for AC adapter (included) and data cable
(sold separately).
User Guide
3
Number keypad continued
11. External speaker.
12. Indicator light shows missed alert when in red or
incoming call when in green.
13. OK key selects a menu item or option.
14. Right softkey accesses the contacts list and other
menu options.
15. Back key erases characters in text entry and returns
you to the previous screen.
16. End/Power key turns the phone on and off, ends a
call or browser session, and returns you to the
home screen.
17. # Space key enters a space during text entry. Press and
hold to activate or deactivate Silent mode.
18. Jack for hands-free headset only (sold separately).
19. 0 Next key cycles through word choices during
text entry.
Warning: Inserting an accessory into the incorrect jack
damages the phone.
4
Phone overview
QWERTY keypad
When the flip is open, use the QWERTY keypad to enter numbers, letters and symbols.
1. Internal screen.
2. Internal speaker.
3. Navigation key scrolls through lists
and text entry fields and accesses
shortcuts from the home screen.
4. Left softkey accesses menus
and functions.
5. Send/Talk key starts or answers a call.
Press once to activate voice command,
twice to display the All Calls list, and
three times to redial the last number
dialed. Press and hold to access
voice dial.
6. Internal Camera key activates camera mode.
7. Messages key accesses the Messages menu.
8. Symbol key allows you to type symbol characters.
9. Shift key changes the text mode in text entry.
10. Space key enters a space during text entry.
11. OK key selects a menu item or option.
12. Right softkey accesses the contacts list and other menu options.
13. End/Power key turns the phone on and off, ends a call or browser session, and returns you to the
home screen.
14. Speakerphone key activates the speakerphone and answers incoming calls.
15. Back key erases characters in text entry and returns you to the previous screen.
16. Enter key allows you to enter hard returns.
User Guide
5
Back cover
1. Accessory eyelet (for optional straps and lanyards).
2. Camera flash and flash light.
3. Camera lens.
4. Back cover lock in unlocked status (If locked, the
screw slot is in horizontal position).
6
Phone overview
Common keys
The following keys are pressed frequently when you use your phone. Throughout this user guide, these
keys are referred as follows:
Navigation key
Messages key (QWERTY keypad)
OK key
Symbol key (QWERTY keypad)
Left softkey (number keypad)
Shift key (QWERTY keypad)
Left softkey (QWERTY keypad)
Right softkey (number keypad)
Right softkey (QWERTY keypad)
Talk/Send key (number keypad)
Talk/Send key (QWERTY keypad)
End/Power key (number keypad)
End/Power key (QWERTY keypad)
Back key (number keypad)
Back key (QWERTY keypad)
Speakerphone key (number keypad)
Speakerphone key (QWERTY keypad)
Camera key (QWERTY keypad)
User Guide
7
Screen icons
These icons may appear on your phone’s screen.
You have a text message.
The phone is operating in IS95 digital mode.
You have a voice message.
New voice and text message.
The phone is receiving a signal. You can make
and receive calls. Fewer bars indicate a
weaker signal.
A call is in progress.
New photo message.
New photo and voice message.
New photo and text message.
New photo, voice and text message.
The phone is not receiving a signal. You
cannot make or receive calls.
The phone is DRM protected.
The phone is roaming outside of its home
service area.
The battery is fully charged. The more black
bars, the greater the charge.
High-speed (3G) data service is available and
active on your phone. Check with your service
provider for availability.
The phone is set to light up instead of ring.
(blinking) The phone is sending
high-speed data.
The phone is set to vibrate or to vibrate and
then ring.
(blinking) The phone is receiving
high-speed data.
Position location is set to your service provider
and to emergency services.
High-speed data service is available, but the
phone is dormant.
Position location is set to emergency
services only.
The alarm clock is set.
The phone is in camera mode.
Camera flash mode is ready.
The phone is in privacy mode or is accessing a
secure Web site.
8
Phone overview
Screen icons continued
Camera zoom mode is ready.
Speakerphone is on.
Auto-Answer is on.
Bluetooth wireless technology is
enabled (On).
Bluetooth wireless technology is disabled
(Off).
User Guide
9
Main menu
The contents of the main menu are as follows:
BREW Apps
MobileShop
Settings
Help
Web Browser
Contacts
View All
Add New
Camera
Launches the Camera
Settings
Sounds
Alerts
Media Galley
Camera Pictures
Images
View Groups
Speed Dial List
Voice Dial List
Messages
New Text Msg
New Picture Msg
Voicemail
Inbox
Browser Alerts
Sent
Outbox
Saved
Drafts
Display
My Phone
Accessories
Network
Security
Bluetooth
On/Off
Launches the Browser
Sounds
Recent Calls
All Calls
Incoming Calls
Outgoing Calls
Missed Calls
Erase Call Lists
Recent Calls Timer
All Calls Timer
Tools & Games
Brick Attack
Race 21™
Voice Memo
Scheduler
Alarm Clock
Tip Calculator
Calculator
My Devices
Settings
Phone Info
Build Info
Icon Keys
Timer
Stopwatch
Msg Settings
Group Lists
Erase Messages
Flashlight
Note: The menu items on your phone can change depending on the services provided.
Check with your service provider.
10
Main menu
Basic navigation
Guide conventions
You press your phone keys to access the various
menus and other features of your phone. Some of
the basic frequently used keys are as follows:
In this guide the following conventions are used
when describing phone features.
Select means to press the left or right softkey, or
the OK key to select an item on the display. For
example, “select Menu” tells you to press the left
softkey at the home screen to access the
main menu.
•
•
•
Left softkey: Selects items that appear on the
lower left of the display. At the home screen,
you can select Menu.
Right softkey: Selects items that appear on
the lower right of the display. At the home
screen, you can select Contacts.
Navigation key: Scrolls through menus and
options. You can access the following
shortcuts from the home screen.
Press means to press a phone key. For example,
“press the Send key to make a phone call” tells
you to press the Send key on your phone.
Scroll means to press the Navigation key to move
though a list on the display. For example, “scroll
through your contacts list to choose a contact”
means to press the Navigation key up or down to
scroll through the list on the display.
–
–
–
–
Press and hold left to launch
Web Browser.
Press and hold right to record a
voice memo.
Press and hold up to access the
custom menu.
Press and hold down to view recent
calls list.
The greater than symbol “>” tells you to select an
option from a menu or list. For example, Menu >
Settings means to:
1. Press the left softkey at the home screen to
select Menu.
•
•
•
OK key: Selects a menu item.
Back key: Returns to the previous menu level.
End/Power key: Returns to the home screen.
2. Scroll to the Settings option.
3. Press the OK key to select Settings.
User Guide
11
2
BASIC FUNCTIONS
This section explains the basic functionality of
your phone. For more detailed explanation of
your phone’s features please refer to the
later chapters.
Call using a contact
At the home screen:
1. Select Contacts to open your contacts list.
2. Highlight a contact and press the Send key.
Powering up
Call using voice commands
To turn on your phone, press and hold the End
key and wait until the phone display lights up. To
turn off your phone, press and hold the End key
until the phone turns off.
You can use voice commands to call a contact
from your voice dial list or to dial a phone
number. For more information, see “Voice
recognition” on page 69.
Making phone calls
Redial a number
Make sure you are in an area where a signal can
be received. Look for the signal strength icon on
the home screen. The more bars you see in this
symbol, the stronger the signal. If there are no
bars, move to where the signal strength is better.
At the home screen:
1. Press the Send key twice to open your
call history.
2. Highlight a phone number or contact and
press the Send key.
When the phone has been idle for a while with no
signal, it changes to power save mode. When you
see “Power Save” on your phone’s screen, press
any key to return to normal operating mode.
Tip: To redial the last number called, received or
missed, press the Send key three times.
Answering phone calls
You can make a phone call in one of the
following ways.
When a call comes in, the phone rings, vibrates,
or lights up. The phone number of the caller also
appears if it is not restricted. If the number is
stored in your contacts list, the contact
name appears.
Call using a number
At the home screen:
1. Enter a phone number.
2. Press the Send key.
You can answer a phone call in one of the
following ways.
12
Powering up
Answer using earpiece
Press the Send key.
Taking a picture
At the home screen:
1. Press and hold the Camera key to start
Answer using speakerphone
Press the Speakerphone key.
the camera.
2. Focus on the image and select Capture.
Answer using flip
For more information, see “Camera” on page 44.
You can set the phone to answer immediately
when you open the flip. This feature does not
apply to incoming data or fax calls.
Using custom menu
You can use the custom menu to quickly access
your frequently used functions.
See “Open to answer” on page 59.
1. At the home screen, press and hold the up
Ending phone calls
Press the End key.
Navigation key to access the custom menu.
2. Select Edit.
3. Scroll through the list of options and press
OK to select your desired option(s). A check
mark appears next to each selected option.
(You can press OK again to remove
check marks.)
Verifying your phone number
To verify your phone number, select Menu >
Phone Info > Build Info.
Activating voice dialing
At the home screen:
4. Select Save after checking all your desired
option(s). Your selected options appear in
the custom menu.
1. Press the Send key once.
2. Follow the prompts.
5. Scroll through the list of your selected
functions in the custom menu and press OK
to access your desired one.
For more information, see “Voice recognition” on
page 69.
User Guide
13
3
CALL FEATURES
This chapter describes call features such as
volume, holding calls, speed dialing and
other features.
Note: In the absence of voicemail, this feature
drops the call.
Hold Calls
The Hold Call feature allows you to place
incoming calls on hold until you are ready to
answer them. See “Hold Call” on page 59.
Volume control
You have several ways to control the volume of
your phone.
Adjust volume during a call
To adjust the earpiece volume during a call, press
Speed dial
Use the speed dial feature to assign a one- or two-
digit shortcut to a contact. Before you can use
speed dialing, you must save a phone number as a
contact and assign a speed dial location to it. See
“Contact number” on page 30.
the Volume key up or down.
Use the speakerphone
Your phone has a built-in speakerphone. To
turn on the speakerphone, press the
Speakerphone key.
To call a contact that has a speed dial location:
1. Enter the one- or two-digit speed
The speakerphone icon appears on the home
screen when the speakerphone is on.
dial location.
2. Press the Send key.
To turn off the speakerphone, press the
Speakerphone key.
1-Touch Dialing
The 1-touch dialing feature is the fastest way to
speed dial a contact that has a speed dial location.
See “1-Touch Dialing” on page 60.
Note: If you press the Speakerphone key during
an incoming call, you answer the call.
Silence an incoming call
To silence the phone without answering the call,
press the End key or select Silence.
To silence the phone and answer the call, press
the End key and then press the Send key.
14
Volume control
3. Follow the system prompts to retrieve
Voicemail
the message.
Configure your voicemail
Set voicemail alert
Before your phone can receive voicemail
messages, you must set up a password and record
a personal greeting with your service provider.
When you have set up your voicemail, all
unanswered calls to your phone are automatically
transferred to voicemail, even if your phone is in
use or turned off.
You can set the phone to beep or vibrate every five
minutes to remind you that you have voicemail.
See “Alerts” on page 41.
Data and fax calls
Your phone may be able to receive certain data or
faxes. See “Data and fax calls” on page 63.
1. With 1-touch dialing enabled, press and hold
the 1 key.
Roaming calls
Set roaming alert
2. Follow the system prompts to create a
password and record a greeting.
You can set roaming alert if you want the phone to
alert you when you roam outside of your home
service area. See “Roaming alert” on page 64.
Check voicemail
When a voice message is received, your screen
displays “New Messages” along with the symbol at
the top of your screen. The symbol flashes if the
message is urgent. If you see “New Messages”:
Roam Option
You can restrict your phone from making a call
when roaming. See “Roam Option” on page 64.
1. Select Call, which initiates a call to your
voicemail number.
Set roam ringer
2. Follow the system prompts to retrieve
the message.
You can set a ringer to indicate when an incoming
call is subject to roaming charges. See “Roam
Ringer” on page 55.
Note: To clear the screen without checking
messages, select Ignore.
If you see only the voicemail message icon:
Set call guard
1. Select Menu > Messages > Voicemail.
You can set the phone to warn you before you
answer or place a call while roaming. See “Roam
Call Alert” on page 65.
2. If you have set up your voicemail, select Call
to call your voicemail number.
User Guide
15
Emergency services
Call emergency service
You can call an emergency code, even if your
phone is locked or your account is restricted.
When you call, your phone enters Emergency
mode. This enables the emergency service
exclusive access to your phone to call you back, if
necessary. To make or receive regular calls after
dialing the code, you must exit this mode.
To dial an emergency code:
1. Enter your 3-digit emergency code.
2. Press the Send key.
Note: Regardless of your 3-digit emergency code
(911, 111, 999, 000, etc.), your phone operates
as described.
Exit emergency services
When you have completed the emergency call:
1. Select Exit.
2. Select Exit again to confirm your choice.
Note: To determine who has access to your
location, see “Location” on page 64.
Airplane Mode
While in an airplane, you can set your phone to
Airplane Mode where your phone does not emit
RF signals. See “Airplane Mode” on page 59.
16
Emergency services
4
TEXT ENTRY
You can enter letters, numbers, and symbols in
contacts, text messages, and your banner with
either QWERTY keypad (flip open) or the number
keypad (flip closed).
There are six text entry modes:
Case Change
Normal Alpha
Rapid Entry
QWERTY keypad
Text entry modes
Numbers and Symbols
With the flip open, enter text with the
QWERTY keypad. The current text entry mode
(and capitalization setting, when applicable) are
indicated by icons.
Add Symbol
Add Smiley
The text entry screen has the following features:
Note: The mode you start in depends on the task
you are doing. For example, when entering a
phone number, you are in Numbers and Symbols
mode. When entering a name for a contact, you
are in Normal Alpha mode.
1. The number of
remaining
characters you can
enter. Allowed
length of messages
can vary depending on your service.
Enter numbers and symbols
2. Text entry fields.
•
•
•
To enter a number or symbol while in
Numbers and Symbols mode, press the
appropriate key once.
To enter a letter while in Numbers and
Symbols mode, press the Symbol key once,
then press the appropriate key.
3. Current capitalization setting.
4. Current text entry mode.
To change to and from Numbers and Symbols
mode, press the Symbol key twice.
User Guide
17
Enter word letter by letter
Change default text entry mode
1. When entering text in Normal Alpha mode,
press the appropriate key once. If your
phone is set to Spanish, French, or
You can change the default text entry mode when
creating a text message. This setting applies only
to the message body screen, not the “To” screen.
Select Menu > Messages > Msg Settings >
Default Text and one of the following:
Portuguese, accented letters are available.
2. To enter a number or symbol while in
Normal Alpha mode, press the Symbol key
once, then press the appropriate key.
•
•
Normal Alpha enter text in letter by letter.
Rapid Mode enter text with word recognition.
3. To change to and from Normal Alpha mode,
Change modes
press the Symbol key twice.
Sometimes you need to change modes. For
example, to enter numbers in an email address
while in Normal Alpha mode, you must change to
Numbers and Symbols mode, enter the numbers,
and then change back to Normal Alpha mode to
complete the address.
Enter symbols
While entering text, you can enter many symbols
with the keypad. To access extra symbols:
1. From the text entry screen select Options >
Add Symbol.
To change text entry modes, press the Symbol key
twice, until the icon for the mode you want
appears at the top of the screen. You can also
select Options and a different mode.
2. Scroll up or down to view the list of symbols.
3. Press the number key corresponding to the
symbol to enter it.
Enter smileys
1. From the text entry screen select Options >
Capitalization
You can change capitalization at any time while
entering text. Simply press the Shift key while in
Normal Alpha mode.
Add Smiley.
2. Scroll up or down to view the list of smileys.
3. Press the number key corresponding to the
smiley to enter it.
18
QWERTY keypad
Text entry quick reference
This table gives instructions for entering letters, numbers, and symbols.
To...
Do this...
Enter a letter
Use Normal Alpha mode and press a key until you see the letter you want.
For more options, see “Text entry modes” on page 20.
Enter a number
Enter a symbol
Use Numbers Only mode and press a key until you see the number you want.
For more options, see “Text entry modes” on page 20.
In either Normal Alpha or Numbers Only mode, press 1 until you find the
symbol you want. For more options, see “Text entry modes” on page 20.
Enter a smiley
Use the Add Smiley feature.
Press the Space key.
Enter a space
Erase a character
Press the Back key.
Erase all characters
Move cursor right or left
Move cursor up or down
Change text entry modes
Capitalize any letter
Press and hold the Back key.
Scroll left or right.
Scroll up or down.
Press the Symbol key twice.
In Normal Alpha mode, press the Shift key to select uppercase if in
lowercase or enter text if already in uppercase.
Lowercase any letter
In Normal Alpha mode, enter text if already in lowercase or press the Shift
key to select lowercase if in uppercase.
Initial caps
In Normal Alpha mode, press the Shift key to select sentence case.
Select soft options on screen
Press the appropriate left or right softkey.
User Guide
19
Note: The mode you start in depends on the task
you are doing. For example, when entering a
phone number, you’re in Numbers Only mode.
When entering a name for a contact, you’re in
Normal Alpha mode.
Number keypad
Text entry modes
When the flip is closed, enter text with the number
keypad. The current text entry mode (and
capitalization setting, when applicable) are
indicated by icons.
Enter numbers
•
To enter a number in Numbers Only mode,
press a number key once.
The text entry screen has the following features:
1. The number of
remaining characters
you can enter. Allowed
length of messages can
vary depending on your
service.
•
To enter a number in Normal Alpha or Rapid
Entry mode, press and hold a number key
until the number appears on the screen.
Enter words letter by letter
1. Press a key once for the first letter, twice for
the second letter, and so on. If your phone is
set to Spanish, French, or Portuguese,
accented letters are available.
2. Text entry fields.
3. Current capitalization setting.
4. Current text entry mode.
There are six text entry modes:
2. Wait for the cursor to move right and enter
the next letter.
Note: To enter a space, press the # Space key.
Case Change
Enter words quickly
Normal Alpha
Rapid Entry
When you press a series of keys in Rapid Entry
mode, your phone checks its dictionary and
guesses at the word you are trying to spell.
Numbers Only
Add Symbol
Add Smiley
1. For each letter of the word you want, press the
key once. For example, to enter the word
“any” press the 2 > 6 > 9 keys.
2. If the word doesn’t match what you want,
press the 0 Next key to look at other
word matches.
20
Number keypad
3. When you see the word you want, press the
•
Rapid Mode to enter text with word
# Space key.
recognition.
Enter symbols
Change modes
While entering text in normal text mode, you can
enter symbols by pressing the 1 key until you see
the symbol you want. Using this method, you have
access to the following symbols:
Sometimes you need to change modes. For
example, to enter numbers in an email address
while in Normal Alpha mode, you must change to
Numbers Only mode, enter the numbers, and then
change back to Normal Alpha mode to complete
the address.
.
@
?
!
-
,
&
:
‘
To access the full set of symbols:
To change text entry modes, press and hold the *
Shift key until the icon for the mode you want
appears at the top of the screen. You can also
select Options and a different mode.
1. From the text entry screen select Options >
Add Symbol.
2. Scroll up or down to view the list of symbols.
3. Press the number key corresponding to the
Capitalization
symbol to enter it.
You can change capitalization at any time while
entering text. Simply press to choose upper or
lower case while in Normal Alpha mode.
Enter smileys
1. From the text entry screen select Options >
Add Smiley.
2. Scroll up or down to view the list of smileys.
3. Press the number key corresponding to the
smiley to enter it.
Change default text entry mode
You can change the default text entry mode when
creating a text message. This setting applies only
to the message body screen, not the “To” screen.
Select Menu > Messages > Msg Settings >
Default Text and one of the following:
•
Normal Alpha to enter text in letter by letter.
User Guide
21
Text entry quick reference
This table gives instructions for entering letters, numbers, and symbols
To...
Do this...
Enter a letter
Use Normal Alpha mode and press a key until you see the letter you want.
For more options, see “Text entry modes” on page 20.
Enter a number
Enter a symbol
Use Numbers Only mode and press a key until you see the number you
want. For more options, see “Text entry modes” on page 20.
In either Normal Alpha or Numbers Only mode, press 1 until you find the
symbol you want. For more options, see “Text entry modes” on page 20.
Enter a smiley
Use the Add Smiley feature.
Enter a space
Press the # Space key.
Erase a character
Press the Back key.
Erase all characters
Move cursor right or left
Move cursor up or down
Change text entry modes
Capitalize any letter
Lowercase any letter
Initial caps
Press and hold the Back key.
Scroll left or right.
Scroll up or down.
Press and hold the * Shift key.
In Normal Alpha mode, press the * Shift key. Choose uppercase.
In Normal Alpha mode, press the * Shift key. Choose lowercase.
In Normal Alpha mode, press the * Shift key. Choose sentence case.
Press the appropriate left or right softkey.
Select soft options on screen
22
Number keypad
5
BREW APPS
Your Kyocera phone has the added ability to
download and manage applications through the
BREW Apps menus.
Downloading an application
To download an application:
1. At the home screen, select Menu >
BREW Apps > MobileShop > Catalog. When
connected to the server, a list of application
types appears under the MobileShop menu.
2. Select an application type. A full list of
applications of your selected type appears.
New applications have an arrow on the left.
Note: Long titles scroll left as you
highlight them.
BREW Apps provides you with the full range of
applications and services from the Internet:
Email, games, relevant news, and much more.
For more information about BREW Apps
capabilities and application pricing, contact your
service provider.
Using BREW Apps
You connect to the server, download applications,
and then manage them as you like. When you
choose an application, you can choose a demo,
various limited use options, or the full version—
all varying in price. If you choose a demo, BREW
Apps notifies you when it has expired. If you
choose a priced version, the amount goes to your
phone bill. The MobileShop also notifies you if
you’re running out of memory. At that point, you
can either disable an application or remove
it completely.
3. Select an application. A list of usages appears.
One or more usages may be available with the
cost specified for each.
4. Select a usage. A confirmation
message appears.
5. Select Yes to confirm. The application is
downloaded to your phone.
Note: Download times vary.
6. To open the application now, select Yes.
You can also select No to return to the
BREW Apps menu, where you see a link to
your new application.
With applications loaded, you can update to
newer versions as they become available.
Note: Your connection to the application
server automatically ends after 30 seconds,
unless you connect again to download more
applications. Press the End/Power key to end
the connection. Closing the flip does not end
your connection.
User Guide
23
Note: If you remove an application, it is removed
completely from your phone. If you want to use it
again, you must pay for it again. If you want to free
up space on your phone, we recommend you
disable the application.
Opening an application
Downloaded applications are stored under the
BREW Apps menu. Each application comes with
its own unique icon to help you identify it easily.
1. At the home screen, select Menu >
BREW Apps.
Disabling an application
Note: The BREW Apps icon always remains
at the top of this menu. Downloaded
applications are listed after.
If you are running out of memory and want to
download more applications without completely
removing those you have paid for, you can simply
disable them. Thus, you can re-download an
application to use it again without paying for
it again.
2. Highlight and select the icon for the
application you want to open.
Viewing application details
You can get information about the size of an
application and how many uses it has left before it
runs out.
1. At the home screen, select Menu >
BREW Apps > Settings > Manage Apps.
2. Select the application and Lock App.
3. Select Yes to confirm your choice.
1. At the home screen, select Menu >
Note: The application is still listed in the
BREW Apps menu. The icon looks like an
empty box.
BREW Apps > Settings > Manage Apps.
2. Select the application you want details for.
Removing an application
Checking available memory
To remove an application:
The amount of available memory depends on the
number of applications you downloaded.
1. At the home screen, select Menu >
BREW Apps > Settings > Manage Apps.
1. At the home screen, select Menu >
BREW Apps > Settings > Manage Apps.
The amount of memory left shows at the
bottom of the screen.
2. Select the application and Remove.
3. Select Yes to confirm your choice.
2. For more detailed memory information,
select System Info.
24
Opening an application
6
WEB BROWSER
You can use your phone to browse the Internet if
you have obtained phone Internet services from
your service provider and if over-the-air Internet
access is available in your area.
4. To choose a site, highlight the link and
select Go.
5. When you have finished using the Internet,
press the End key to exit.
Note: You cannot receive incoming calls while
you are using Web Browser.
Using Web menu options
The following options may appear during a
Web session.
Launching Web Browser
At the home screen:
•
•
•
•
Home returns you to the main Web Browser
window, or home page.
Mark Site saves the current location as a
bookmark for easy access.
Bookmarks displays a list of your saved
Web sites.
Setup gives you options for changing how
information is displayed.
1. Select Menu > Web Browser.
A message about airtime fees appears every
time you start the browser.
For more information about how airtime is
charged, contact your service provider.
2. Select OK to continue.
If this is the first time you have connected to
the Internet, a message informs you that
security is not yet enabled for your
Web Browser.
–
–
Show URL displays the entire URL.
About Openwave displays information
about your Web Browser version.
Encryption should not be used unless
you are instructed to do so by your
service provider.
UP.Link selects a different browser server.
You can use this option if you have more
than one Web Browser account.
Restart restarts the Web Browser.
–
–
–
3. Select Yes to enable security.
When you are connected, a browser home
page appears. It has a list of bookmarks and
some Web menu options at the bottom of
the screen. The lock icon appears in a
secure session. An underline and an arrow
indicate that there is more text. Scroll down
to view more text. Press the Back key to
return to the previous screen.
User Guide
25
Searching for Web site
How you search for a Web site depends on your
service provider. For more information, contact
your service provider.
Web Alert
You can set a prompt to confirm the start or exit
of the Web Browser.
Select Menu > Settings > Network > Web Alert
and one of the following:
Using bookmark
•
•
•
•
At Start to set a prompt when you start
a session.
At End to set a prompt when you end
a session.
Both to set a prompt when you start or end
a session.
No Prompts for no prompts.
At the home screen:
1. Select Menu > Web Browser.
2. Select OK to accept browser fees.
3. From your Web home page, select
Bookmarks. A list of bookmarks appears.
4. Enter the number corresponding to the
bookmark you want and press the OK key.
Checking Browser Alerts
Alerts received from a Web site are sent to your
Browser Alerts folder. To check them:
1. Select Menu > Messages > Browser Alerts.
This action launches the browser inbox.
2. Select OK to accept browser fees.
3. Select an alert and follow the prompts.
26
Searching for Web site
7
RECENT CALLS
–
–
–
Send Text Msg sends a text message to
the number.
Call lists
Details on the last 60 calls you made, received, or
missed are stored in the Recent Calls list and are
identified by the following icons:
Send Picture Msg sends a picture
message to the number.
Erase Record deletes the call from the
call list.
Outgoing call
Incoming call
Note: If the phone number is classified as
“secret,” you must enter your four-digit lock code
to access it.
Deal with missed calls
Missed call (flashing)
View recent calls
When you have missed a call, “Missed Call”
appears on your screen unless the caller leaves a
voicemail. You can do one of the following:
•
•
To clear the screen, select OK.
To view the call details, select Calls and press
the OK key.
1. Select Menu > Recent Calls and one of the
following:
–
All Calls displays all calls made or
received.
•
To return the call, select Calls and press the
Send key.
–
–
–
Incoming Calls displays calls answered.
Outgoing Calls displays calls made.
Missed Calls displays calls received, but
not answered.
Set alert for missed calls
You can set an alert to beep every five minutes
after you have missed a call. Select Menu >
Settings > Alerts > Missed Call Alert. See
“Other alerts” on page 56.
2. Highlight a recent call.
3. Press the Send key to call the number or
select Options and one of the following:
–
Save creates a new contact or View
displays the contact’s detail screen.
User Guide
27
Erase call lists
You can erase your phone’s call lists.
1. Select Menu > Recent Calls >
Erase Call Lists > All Calls, Incoming
Calls, Outgoing Calls, or Missed Calls.
2. Select Yes.
Call timers
View call timers
Select Menu > Recent Calls and one of
the following:
•
•
Recent Calls Timer tracks all calls you have
made and received since you last reset this
timer. To reset this timer to zero, select Reset.
All Calls Timer tracks all calls you have made
and received. You cannot reset this timer.
Time your calls
Your phone can alert with a short beep ten
seconds before each minute passes during a call.
Select Menu > Settings > Alerts >
Minute Alert > Enabled.
28
Call timers
8
CONTACTS
Use your phone’s contacts list to store information
about a person or company. Each contact entry
can have up to six phone numbers, two email
addresses, two Web addresses, two street
addresses, and a space for notes.
–
–
Send All to send all contact information.
Contacts Menu to access your contacts.
Adding contacts
Add contact from home screen
Viewing contacts list
To view existing contacts in your phone, open the
flip and select Menu > Contacts > View All. Your
contacts list is displayed alphabetically.
To add a contact to your contacts list:
1. From the home screen, enter a phone
number to save (including the area code).
2. Select Save > Save New Contact.
Tip: You can also select Contacts from the home
screen to view the directory.
3. Enter a name for the contact. For more
information, see “Text entry” on page 17.
Scroll to highlight the contact you want and you
can do one of the following:
4. Enter additional phone numbers, email
addresses, Web addresses and note, if
needed. Scroll up or down to move through
the contact fields.
•
Press the Send key to call the
highlighted contact.
•
Press the OK key to view the highlighted
contact’s detail.
5. When you are done entering information,
select Save.
•
•
Select New to add a new contact.
Select Options to choose one of the following:
Add contact from contacts menu
To add a contact to your contacts list:
–
–
–
Call to make a call.
Send Text Msg to send a text message.
Send Picture Msg to send a
1. Select Menu > Contacts > Add New.
2. Enter a name for the contact. When you are
done, scroll down to move to the next field.
For more information, see “Text entry” on
page 17.
picture message.
–
–
–
–
View Contact to view contact details.
Edit Contact to edit contact details.
Erase Contact to erase the contact.
Send as vCard to send contact as a vCard.
3. Enter a primary number for the contact.
User Guide
29
4. Enter additional phone numbers, email
addresses, Web addresses and note, if
needed. Scroll up or down to move through
the contact fields.
2. From the contacts list, select a contact.
3. At the contact’s detail screen, select Edit.
4. Edit or add phone numbers, email
addresses, Web addresses, Street addresses,
and notes. Scroll up or down to move
through the contact fields.
5. When you are done entering information,
select Save.
5. When you are done entering information,
Add code or extension
select Save.
When you save the phone number of an
automated service, you may include a pause to
stop dialing. For example, a pause where you
would wait to dial an extension.
Contact name
To work on the name of an existing contact:
1. Select Menu > Contacts > View All.
2. From the contacts list, select a contact.
1. From the home screen, enter a
phone number.
3. At the contact’s detail screen, highlight
2. Select Options and a type of pause:
the name.
–
Time Pause causes the phone to stop
dialing for two seconds.
4. Select Options and one of the following:
–
Ringer assigns a specific ringer to
the contact.
–
Hard Pause causes the phone to stop
dialing until you select Release while
making the call.
–
Picture assigns a specific picture to
the contact.
3. Enter the remaining numbers and select
–
–
Erase Contact erases the entire contact.
Send as vCard sends the contact as
a vCard.
Save.
4. Select Save New Contact.
5. Complete the contact and select Save.
Contact number
Working with contacts
To work on the number of an existing contact:
1. Select Menu > Contacts > View All.
2. From the contacts list, select a contact.
Contact details
To edit details of an existing contact:
3. At the contact’s detail screen, highlight a
1. Select Menu > Contacts > View All.
contact number.
30
Working with contacts
4. Select Options and one of the following:
Contact email address
To work on the email address of an
existing contact:
–
–
–
–
Call sends a call.
Send Text Msg sends a text message.
Send Picture Msg sends a picture message.
Add Speed Dial adds the number to your
speed dial list.
1. Select Menu > Contacts > View All.
2. From the contacts list, select a contact.
3. At the contact’s detail screen, highlight a
–
–
View Number displays the number.
Erase Number erases the number from
the contact.
contact email address.
4. Select Options and one of the following:
–
–
Send Text Msg sends a text message.
Send Picture Msg sends a
picture message.
–
Secret makes the number secret, hiding it
from the screen until you enter the lock
code. Secret numbers can be called
without a lock code. For more
information, see “Lock Phone” on
page 65.
–
–
–
–
View Address displays the email
address.
Add to Group adds the email address to
the business, personal or custom group.
Erase Address erases email address
from the contact.
Secret makes the address secret, hiding
it from the screen until you enter the
lock code.
–
–
–
–
–
Primary Number makes this number the
primary number for the contact.
Send as vCard sends the contact as
a vCard.
Add to Group adds the number to the
business, personal or custom group.
Add Voice Dial records a voice tag so you
can call a contact using voice recognition.
Erase Voice Dial erases the voice tag
associated with the number.
–
Send as vCard sends the contact as
a vCard.
Contact Web address
To work on the Web address of an
existing contact:
–
–
Edit Voice Dial re-records the voice tag.
Prepend displays the contact’s detail
screen for you to change the number
(adding an area code) or other data of
the contact.
1. Select Menu > Contacts > View All.
2. From the contacts list, select a contact.
3. At the contact’s detail screen, highlight a
contact Web address.
User Guide
31
4. Select Options and one of the following:
Contact note
–
Launch Web launches the Web Browser
and goes to Web address.
Send Picture Msg sends a
picture message.
To work on the note of an existing contact.
1. Select Menu > Contacts > View All.
2. From the contacts list, select a contact.
–
3. At the contact’s detail screen, highlight a
–
–
View Web displays the Web address.
Erase Web erases the Web address from
the contact.
note.
4. Select Options and one of the following:
–
–
View Note displays the note.
Erase Note erases the note from
the contact.
Secret makes the note secret, hiding it
from the screen until you enter the
lock code.
–
–
Secret makes the address secret, hiding it
from the screen until you enter the
lock code.
Send as vCard sends the contact as
a vCard.
–
–
Contact street address
To work on the street address of an
existing contact:
Send as vCard sends the contact as
a vCard.
Assign ringer to contacts
To assign a ringer:
1. Select Menu > Contacts > View All.
2. From the contacts list, select a contact.
1. Select Menu > Contacts > View All.
2. From the contacts list, select a contact.
3. At the contact’s detail screen, highlight a
contact street address.
3. At the contact’s detail screen, highlight the
4. Select Options and one of the following:
contact name.
–
–
View Address displays the street address.
Erase Address erases the street address
from the contact.
4. Select Options > Ringer > Assign Ringer.
5. Select a ringer from the list. (Scroll through
the list to hear the different ringers.)
–
–
Secret makes the address secret, hiding
it from the screen until you enter the
lock code.
Send as vCard sends the contact as
a vCard.
Assign picture to contacts
To assign a picture:
1. Select Menu > Contacts > View All.
32
Working with contacts
2. From the contacts list, select a contact.
Send a vCard
3. At the contact’s detail screen, highlight the
To send contact information as a message:
1. Select Menu > Contacts > View All.
2. From the contacts list, select a contact.
contact name.
4. Select Options > Picture > Assign Picture
and one of the following:
3. At the contact’s detail screen, highlight the
–
Camera Pictures to select a picture from
your Camera Pictures folder.
contact name.
4. Select Options > Send as vCard and one of
–
Images to select an image from either
your Saved images or Caller IDs.
the following:
–
–
–
via Text Msg (See “Create a text
message” on page 34.)
via MMS Msg (See “Create a multimedia
message” on page 36.)
via Bluetooth (See “Bluetooth®
Wireless Technology” on page 67.)
5. Scroll to select your desired picture.
Note: With Mobile Phone Tools (MPT) for
Kyocera, you can transfer digital pictures to your
phone. To purchase MPT or other accessories
Assign number type
Searching contacts
When you assign a number type, an icon is placed
in front of the contact number to specify the type
of number it is.
To find a phone number or contact, you can
search the contacts list, use the Fast Find, or
check the Frequent List. See “Fast Find” on
page 59 and “Frequent List” on page 59.
1. Select Menu > Contacts > View All.
2. From the contacts list, select a contact.
3. At the contact’s detail screen, select Edit.
To search your contacts list, select Menu >
Contacts > View All, View Groups, Speed Dial
List or Voice Dial List.
4. Scroll down twice to highlight the number
type dropdown and press the OK key.
You can also use the Contacts shortcut from the
home screen to view the contacts list. To quickly
get down the list, enter the first letter of the
contact. You skip to that letter of the alphabet.
5. Select General, Work, Home, Mobile,
Pager or Fax. The appropriate icon appears
next to the number in your phone lists.
6. Select Save.
User Guide
33
9
MESSAGES
This chapter describes how to send, receive, and
erase messages from your phone. For information
on voicemail messages,
3. At the Message field, enter the message.
4. Select Send.
Include QuickText and symbols
see “Voicemail” on page 15.
During text entry, you can insert prewritten text
(QuickText), symbols or smileys.
1. From the text entry screen, select Options and
one of the following.
Note: The features and menus described in this
chapter may vary depending on services available
in your area. Check with your service provider for
details and possible usage charges.
–
–
–
Insert QuickText to insert prewritten text
from a list.
Add Symbol to insert symbols. Press the
corresponding number to select a symbol.
Add Smiley to insert smileys. Press the
corresponding number to select a smiley.
Text messages
You can only send text messages to phones
capable of receiving them or to email addresses.
Create a text message
At the home screen:
1. Select Menu > Messages > New Text Msg.
2. At the Send To field, do one of the following
to enter the recipient’s phone number or
email address:
2. Complete your message.
3. Select Send.
Use text message options
When you are ready to send a text message, you
have several options for how and when you want
it received.
–
Select Options > Recent List,
Recent Calls, Contacts or Groups to
access your stored contacts.
1. After composing your message, select
–
Enter the phone number or email address
manually. See “Text entry” on page 17.
Options and one of the following:
–
Add Address returns you to Send To field
to add another recipient.
You can message up to ten recipients at once.
Use a comma or spaces to separate addresses.
If you select stored contacts, this is done
automatically. Scroll down to move to the next
field when done.
–
Save Message saves the messages in your
Drafts folder. This prevents the message
from being deleted if you activate
Auto-Erase.
34
Text messages
–
Save QuickText saves the message you
composed as a pre written message.
Message notifications
If you see a message notification, select Inbox to
view messages. Choose a message and select View
to open it. To clear a message notification,
select Ignore.
–
Settings > Request Receipt alerts you
when a recipient has received your
message.
–
–
Settings > Set Priority labels the
message as urgent.
Settings > Callback Number includes a
callback number with the message.
Select OK to include your own number
or enter a different one.
Settings > Send Later schedules a time
to send the message.
Settings > Validity Period sets a defined
expiration time limit for a message.
Message icons
If you see the message icon, select Menu >
Messages > Inbox. Choose a message and select
View to open it.
View a text message
–
–
The options available when viewing a text message
may vary. Check with your service provider.
1. Select Menu > Messages > Inbox.
2. Select View to read a message. If the
message is long, scroll down to view the
entire message.
2. After setting options, press the Back key to
return to the message window.
3. Complete your message.
3. Select Reply to create a response message or
Options and one of the following:
4. Select Send.
–
–
Erase erases the message.
Lock Msg protects the message from the
accidentally deleted.
Retrieve a text message
When a text message is received, your phone
displays a notification and the message icon
appears at the top of your screen. The message
icon flashes if the message is urgent. Urgent
messages are also marked in the Inbox.
–
–
Forward forwards the message.
Reply with Copy replies to the message
with a copy of the original attached.
Save Message saves the message.
Save QuickText saves the message text as
QuickText, which you can insert into other
messages. Graphics and sounds are
not saved.
–
–
User Guide
35
–
Sender displays the sender information.
–
Enter the phone number or email
address manually. See “Text entry” on
page 17.
Note: If a graphic is too large or incorrectly
formatted, and is not received with the message,
an icon appears.
Note: You can message up to ten recipients
at once. Use a comma or spaces to separate
addresses. (If you select stored contacts,
your phone does this automatically.)
Multimedia messages
You can only send multimedia messages to
phones that are capable of receiving them or to
email addresses.
3. At the Subject field, enter a subject. Scroll
down to move to the next field when done.
Multimedia messages have a predetermined
character and file size limit. When you reach the
character and file size limit for a single
multimedia message, you must edit the message
to meet the size limitation.
4. At the Text field, enter a message. Scroll
down to move to the next field when done.
5. At the Image field, select Options and one of
the following to attach a file:
–
–
Take Picture to instantly take a photo
and attach it.
Media Gallery to attach an existing file
from Camera Pictures or Images.
Note: Multimedia messaging is not available on
all phones. Check with your service provider.
Create a multimedia message
At the home screen:
Scroll down to move to the next field
when done.
1. Select Menu > Messages >
6. At the Sound field, select Options and one of
New Picture Msg.
the following to attach a file:
2. At the To, CC (to send a copy of the
message), and BCC (to send a blind copy)
fields, do one of the following to enter
the recipient’s phone number or email
address. Scroll down to move to the next
field when done.
–
–
Record Sound to instantly record a
sound and attach it.
Media Gallery to attach an existing file
from Saved Sounds, Ringers or
Voice Memos.
7. Select Send.
–
Select Options > Recent List,
Recent Calls, Contacts, or Groups to
access your stored contacts.
36
Multimedia messages
Auto retrieve mode
Use multimedia message options
When a message is received, it is automatically
downloaded onto your phone. A notification
appears when a new message has been
downloaded to your phone. Select one of
the following:
When you are ready to send a multimedia
message, you have several options for how and
when you want it received.
1. While composing your message, select
Options and one of the following:
•
•
View opens the message.
–
–
–
Insert Contacts adds contacts to your
message.
Quick Text adds prewritten text to your
message.
Save QuickText saves your message as
prewritten text.
Preview Message plays your message.
Save Message saves the message to the
draft folder.
Add Address adds additional recipients to
your message.
Message priority labels the message
as urgent.
Later saves the message for you to view later.
Note: If a message is received during a call, the
phone downloads the message approximately one
minute after the last key is pressed.
Prompt mode
–
–
When a multimedia message is received, it is not
automatically downloaded onto your phone.
A notification appears when a new message
is available for download. Select one of
the following:
•
•
•
–
–
Yes downloads and opens the message.
Erase deletes the message.
Retrieve Later sends the message to the
Inbox for you to download and view later.
2. After setting options, press the Back key to
return to the message window if necessary.
3. Complete your message.
Note: If a multimedia message is received during
a call, the phone displays a notification after the
call ends.
4. Select Send.
Retrieve a multimedia message
There are two modes for receiving a multimedia
message on your phone: Auto Retrieve (default)
and Prompt.
User Guide
37
–
Message Info displays the message
information (priority, sender,
subject, time sent and received,
and message size).
Recipients displays all the addressees
present in the "To" and "CC" fields.
Replay plays the message again from
the beginning.
Save Picture saves the picture embedded
in the message.
Save Sound saves the sound embedded
in the message.
View a multimedia message
When a multimedia message is received, the
message icon appears at the top of your screen.
The message icon flashes if the message is urgent.
All notifications or messages are stored in the
Inbox regardless of your Auto Retrieve settings.
–
–
–
–
–
1. Select Menu > Messages > Inbox.
2. Select View to read a message. If the
message is long, scroll down to view the
entire message.
3. Select Reply to create a response message or
Options and one of the following:
Lock/Unlock Msg disallows or allows
erasing the message accidentally.
Erase deletes the message.
Done exits the message.
–
–
–
Mute/Unmute enables or disables
silencing the message.
Reply All creates a response message to
all recipients.
Forward forwards the message without
showing the original address, graphic,
sound, and text fields.
–
–
Note: The options available to you may vary.
Check with your service provider.
Erasing messages
It is a good idea to erase old messages to free up
memory in your phone.
–
–
Call calls the message sender.
Save QuickText saves the text in the
message to the QuickText list.
Save Address extracts email addresses,
phone numbers, and/or URLs from the
sender information and message body.
Save Message saves the message to the
Saved Folder.
You can erase messages and pages as you send or
read them, erasing them one at a time, or erasing
them all at once.
–
–
38
Erasing messages
Erase a single message
Appended messages
At the home screen:
If you go over the character limit for a single
message, the phone may automatically append an
empty segment to your message to make space.
1. Select Menu > Messages > Inbox, Sent,
Outbox, Saved, or Drafts.
Important: Your service provider charges you
for each message segment.
2. Highlight the message you want to erase.
3. Select Erase or Options > Erase depending
When you start a message, the maximum
character limit appears once you are in the
message entry field. This number counts down as
you enter characters, until it reaches 0.
on your selected folder.
4. At the notification, select Yes to erase
the message.
Erase all messages
At the home screen:
If you continue to enter text after this counter
reaches 0, a message segment may be appended.
When you reach the message size limit, you are
prompted to edit the message or alerted that the
message is being appended.
1. Select Menu > Messages >
Erase Messages > Inbox, Sent, Outbox,
Saved Folder, Drafts Folder or
All Messages.
Note: Appended messages may not be available
on all phones. Check with your service provider.
To erase messages from all folders, select
All Messages.
Receive incoming calls while
creating messages
If you receive a call while creating a message, a
notification appears. You can do the following:
2. At the notification, select Yes to erase
the messages.
Working with messages
The following are some messaging tips.
•
Select Ignore to return to the message
creation screen without answering the call.
Press the Call key to answer the call and save
the created message to the Drafts folder.
•
Unable to send messages
You may not be able to send or receive messages
if your phone’s memory is nearly full, or if digital
service is not available at the time. To free up
memory, erase old messages.
See “Erasing messages” on page 38.
User Guide
39
Complete messages in Drafts folder
View failed or pending messages
To continue composing a message in the
Drafts folder:
Failed or pending messages are stored in your
Outbox folder. To view messages in the Outbox
folder, select Menu > Messages > Outbox.
1. Select Menu > Messages > Drafts.
2. Highlight the message you want to complete.
3. Select Edit.
Your list of failed or pending messages will
appear with the following symbols.
The message is pending and will be
sent when possible. You can cancel
delivery of the message.
4. Complete your message.
5. Select Send.
View messages in Sent folder
To view messages in the Sent folder, select
Menu > Messages > Sent.
The message cannot be sent because
service is not available. An alert
appears on your phone if the message
cannot be sent.
Scroll through the list of messages. One of the
following indicators may appear next to
each message:
Creating group lists
You can create and save a list of multiple
recipients. You phone stores five group lists with
up to ten recipients per list.
The scheduled message was sent and
delivered as scheduled. You cannot
cancel delivery of the message.
1. Select Menu > Messages > Group Lists >
Create New.
The message has been received.
2. Enter a name for the group.
3. Select Next.
4. To enter the first recipient, select one of
the following:
The message has never been sent or
has not been sent since it was last
modified. You can cancel delivery of
the message
–
Recent List to select a number from your
recent calls.
The message has been sent to more
than one recipient.
–
New Address to enter one or more
recipient’s address manually.
40
Creating group lists
–
Contacts List to select a recipient from
your contacts list.
Signature
The signature you create is included at the end of
all outgoing messages and is counted as
characters in your messages; however, it does not
appear in the message creation screen.
Select Options > Recent List or Contacts if
you need to enter multiple recipients.
5. When you have completed entering recipients,
select Done.
1. Select Menu > Messages > Msg Settings >
You can now send messages to the new group.
Signature.
2. Enter your signature in the text field.
Message settings
3. Select OK to save the signature.
Message settings help configure your phones text
and picture message settings.
Note: The characters in the signature are
included in the total character count of
the message.
Alerts
To choose how to be alerted of voicemail, pages,
or text messages, select Menu > Messages >
Msg Settings > Alerts > Message Alert,
Page Alert, or Voicemail Alert and one of
the following:
Edit QuickText
Your phone comes with prewritten (QuickText)
messages, such as “Please call me,” which you
can insert into the body of a text message. You can
edit these messages or create new ones. Your
phone stores up to 40 QuickText messages, with
up to 100 characters per message.
•
•
Disabled turns off the sound alert.
Vibrate, Beep, Freeway, Game, Bloop,
Winner, or Zilofon sets the phone to alert you
once when receiving a new message.
1. Select Menu > Messages > Msg Settings >
Edit QuickText and one of the following:
•
Vibrate & Remind, Beep & Remind, Fwy &
Remind, Game & Remind, Bloop & Remind,
Winner & Remind, or Zilofon & Remind
notifies you once when receiving a new
message and again every five minutes. To stop
a reminder alert, select Ignore.
–
Highlight a QuickText message and
select Edit.
–
Select New Msg to create a new
QuickText message.
2. Enter or edit the text.
3. Select Done.
Note: You can also save a message you have
written or received as QuickText.
User Guide
41
Auto Retrieve
Save to Sent
To set your phone to automatically retrieve
multimedia messages, select Select Menu >
Messages > Msg Settings > Auto Retrieve and
one of the following:
You can save your outgoing messages. Select
Menu > Messages > Msg Settings >
Save to Sent and one of the following:
•
•
Disabled does not save outgoing messages.
Prompt allows you to choose whether or not
to save your message when you send it.
Enabled saves all outgoing messages to the
Sent folder.
•
•
Enabled turns on auto retrieve.
Disabled turns off auto retrieve. You are
prompted before any multimedia messages
are downloaded.
•
Show/Hide CC/BCC
Auto-Erase
To show or hide the CC and BCC fields when you
are composing a picture message, select Menu >
Messages > Msg Settings > Show CC/BCC or
Hide CC/BCC.
You can set your phone to erase messages
automatically when memory is needed for
incoming messages.
Select Menu > Messages > Msg Settings >
Auto-Erase and one of the following:
Callback Number
Set a callback number to let recipients know at
what number they can call you back.
•
•
Disabled erases no messages.
Inbox Msgs erases old messages in your
Inbox when memory is needed.
1. Select Menu > Messages > Msg Settings >
•
•
Sent Msgs erases old messages in your Sent
folder when memory is needed.
Callback Number.
2. Enter a number in the text field.
Both erases old messages in both your Inbox
3. Select OK to save the number.
and Sent folder when memory is needed.
Text and Picture Message Receipt
To request a notification when a recipient has
received a text or multimedia message, select
Menu > Messages > Msg Settings >
Text Msg Receipt or Pict Msg Receipt >
Request.
42
Message settings
Default Text
You can change the default text entry mode when
creating a text message. This setting applies only
to the message body screen, not the “To” screen.
Select Menu > Messages > Msg Settings >
Default Text and one of the following:
•
•
Normal Alpha to enter text in letter by letter.
Rapid Mode to enter text with word
recognition.
Voicemail Number
Set the number your phone calls to retrieve
voicemail. Often your voicemail number is
automatically programmed by your
service provider.
1. Select Menu > Messages > Msg Settings >
Voicemail Number.
2. Select Edit.
3. Enter the voicemail number. Use Option >
Time Pause or Hard Pause to enter pauses.
4. Select Save.
User Guide
43
10 CAMERA
The following are some tips for you to operate
your phone’s camera:
The picture is saved to your Camera
Pictures folder.
•
You cannot activate the camera while on an
active call or while browsing files in the
media gallery.
4. Select Send to create a multimedia
message or Erase to delete the picture
from your phone.
•
•
•
Once the camera is active, the home screen
acts as the viewfinder.
5. Press the End key to exit camera mode.
If you get a “Low memory” error, check your
resolution and quality compression settings.
If there is no activity within 45 seconds after
you turn your camera on, the camera quits
and returns to the previous launch point.
Menu settings and options can only be
accessed when the camera is active.
Camera mode options
You can set up how your camera takes pictures.
While in camera mode, select Options and one of
the following:
•
Settings displays the following camera
settings you may set up prior to taking
a picture:
•
–
–
–
–
Flash sets the camera flash as Automatic,
On, or Off.
Resolution sets the horizontal and vertical
number of pixels for the picture.
Low Light Mode brightens the picture for
low light environments.
Self Timer sets up a countdown timer to
automatically take a picture when the
timer expires. When set, the camera beeps
from 3 seconds down to the time the
shutter automatically snaps the picture
(unavailable for Multishot mode).
Taking a picture
To take a picture:
1. Activate the camera in one of the
following ways:
–
Press the Camera key until the camera
screen appears.
–
Select Menu > Camera.
2. Focus on the image using the phone’s display
as a viewfinder.
3. Take a picture in one of the following ways:
–
–
–
Press the OK key.
Press the Camera key.
Select Capture.
44
Taking a picture
–
Multishot takes up to six multiple pictures
with the Camera key pressed and held. A
tone plays each time a picture is taken. A
second tone plays when the final picture
is taken.
•
Frames adds a frame or a stamp to your
picture. A frame or stamp cannot be removed
once it has been used in a picture. The picture
resolution changes to 120 x 160 (with the
number keypad) or 160x120 (with the
QWERTY keypad) while taking pictures with
Frames enabled. The resolution returns to the
original setting with Frames disabled.
–
–
–
–
Shutter Sound sets the sound used when
the camera takes a picture.
White Balance adjusts the camera for
different lighting.
Color Tone sets the color tone of
the picture.
Quality sets the picture compression. The
higher the compression, the better the
detail of the picture (higher pixel rate).
When set to High, the picture file size is
larger, using more memory.
Note: The following settings revert to the default
setting each time you enter and exit the camera
application: Low Light Mode, Self Timer,
MultiShot, and Viewfinder Display.
Camera indicators and icons
The camera may display the following on screen
indicators and icons.
–
–
LED flashes the indicator light when taking
a picture.
Viewfinder Display sets the camera
viewfinder as Fullscreen or Actual.
Note: Numbers in the top right corner indicate
the number of snapshot remaining. Numbers in
the bottom left corner indicate the resolution
setting for pictures.
•
•
•
Brightness adjusts the brightness of the image
in the home screen LCD.
Camera Pictures displays all pictures taken
and stored.
Last picture displays the most recently
taken picture.
Flash is on.
Camera is in camera mode.
Multishot feature is on.
Self-timer feature is on
Camera zoom mode is ready.
User Guide
45
11 MEDIA GALLERY
The Media Gallery stores camera pictures,
images, and sounds in the phone and displays
those files on the phone’s screen.
–
Modify > Options > Rotate rotates the
picture by 90° right, 180°, 90° left, flip
horizontal or flip vertical.
–
–
–
–
–
–
–
Modify > Options > Resize resizes the
picture to 90%, 75%, 50%, or 35%.
Modify > Options > Brightness adjusts
the brightness.
Modify > Options > Sharpness adjusts
the sharpness.
Modify > Options > Saturation adjusts
the saturation.
Modify > Options > Hue adjusts the
hue.
Modify > Options > Auto Adjust
automatically adjusts all levels.
Modify > Options > Color Tone
changes the picture to grayscale,
negative, sepia, or emboss.
Accessing folders
To access the folders where your phone
stores files, select Menu > Media Gallery and
one of the following:
•
•
•
Camera Pictures displays thumbnails of the
photos you have taken.
Images contains images files that are
preloaded, downloaded, saved or created.
Sounds contains sound files that are
preloaded, downloaded, saved or created.
Browsing camera pictures
To browse the Camera Pictures folder:
1. Select Menu > Media Gallery >
–
–
–
Zoom zooms in or out on the picture.
Take picture activates camera mode.
Lock/Unlock disables or enables
accidental erasing of the picture.
Rename renames the picture.
Details shows the file details.
Camera Pictures.
2. At your picture list, highlight a picture and
select View.
3. Select Send to create a message with the
picture attached or select Options and one
of the following:
–
–
–
–
Erase erases the picture.
Assign assigns the picture as a Caller ID
or wallpaper.
46
Accessing folders
Browsing images
To browse the Images folder:
Browsing sounds
To browse the Sounds folder:
1. Select Menu > Media Gallery > Images and
1. Select Menu > Media Gallery > Sounds and
one of the following:
one of the following:
–
–
Saved images displays images available.
Wallpapers displays wallpapers
available.
Screensavers displays screen
savers available.
–
–
–
Saved Sounds displays sounds available.
Ringers displays ringers available.
Voice Memos contains voice memos you
have made.
–
–
2. At the folder list, highlight a file.
Caller IDs displays the IDs you have
assigned to pictures and images.
3. Depending on your selection, you can do the
following:
2. Highlight a file and select View.
–
–
–
With Saved Sounds selected, select Send
to create a message or Options > Assign
to assign the selected sound.
With Ringers selected, select Assign to
assign the sound or Options > Details to
check the file details.
With Voice Memos selected, select Send
to create a message or Options > Play,
Record new, Erase, Lock, Rename,
Details, or Erase All to perform your
desired task on the selected sound.
3. Depending on your selection, you can do
the following:
–
With Saved images selected, select Send
to create a message or Options to
perform your desired task on the
selected image.
–
–
With Wallpapers or Screensavers
selected, select Set default to assign the
image or Details to check the file details.
With Caller IDs selected, select Assign to
assign the selected image or Details to
check the file details.
Playback tools
Use the Navigation key to select the playback
tools displayed on the screen. See “Playback
tools” on page 49.
User Guide
47
12 TOOLS & GAMES
Your phone comes with tools and games. Some of
the games or tools described here may not be
available on your phone.
Race 21
This game is a timed variation of Black Jack. Each
game comprises three 90-second rounds. To
score points, add cards in each of the four
columns, trying to reach but not exceed 21 in
each column during the course of the game.
If you receive an incoming call while you are
playing a game, the game is paused and exited.
You can return to play once the call alert ends.
Games do not remain paused if the phone is
turned off or loses power.
1. Select Menu > Tools & Games > Race 21.
2. At the notification, select Yes to
conserve battery.
Brick Attack
3. Select New Game to start the game. You have
The goal of this game is to eliminate bricks
arranged in levels. You send a moving ball
upward using a paddle at the bottom of
the screen.
the following options:
–
–
–
Scroll left and right to place the cards.
Press the Back key to pause the game.
Select Continue Game to restart the
game.
1. Select Menu > Tools & Games >
Brick Attack.
–
Select Exit Immediately to exit the game.
2. At the notification, select Yes to
conserve battery.
Voice Memo
3. Select New to start the game. You have the
The voice memo tool enables you to record and
play back audio memos.
following options:
–
–
–
–
Scroll left and right to move the paddle.
Press the Back key to pause the game.
Select Resume to restart the game.
Select Options > Exit to exit the game.
Record voice memos
To record new voice memos:
1. Select Menu > Tools & Games >
Voice Memo > Record New.
Or press and hold the right Navigation key at
the home screen.
48
Brick Attack
2. Record your voice memo. Select Stop when
Start or continue the file.
Stop the playback.
you are done.
3. Select Save to save your memo.
If you receive an incoming call while recording a
memo, the memo is saved and the incoming call
screen appears.
Pause the playback.
Mute the playback.
Unmute the playback.
Review voice memos
To play and use voice memos:
1. Select Menu > Tools & Games >
Scheduler
Voice Memo > Recorded Memos.
Use the scheduler to schedule events and set
reminder alerts.
2. At the file list, highlight a file.
3. Select Send to create a message with the
memo attached or select Options and one of
the following:
Create an event
1. Select Menu > Tools & Games >
–
–
Play to hear the memo.
Record new to record a new voice
memo.
Scheduler > Add New Event.
2. At the Event Name field, enter a name. Scroll
down to move to the next field when done.
–
–
Erase to erase the memo.
3. At the Type field, press OK and scroll
Lock/Unlock disables or enables
accidental erasing of the voice memo.
Rename to rename the sound.
Details to look at details of the file.
Erase All to erase all memos stored.
through the list to select a type.
4. At the Date field, press OK to change
–
–
–
the date.
–
Scroll left or right to move between
month, day, and year fields.
Scroll up or down to change month, day,
and year.
Playback tools
–
When you playback a sound file, use the
Navigation key to select the playback tools
displayed on the screen.
Press OK to save date and move to the
next field.
User Guide
49
5. At the Time field, press OK to change the time.
View events
You can view the events saved to the scheduler.
–
Scroll left or right to move between hour,
minute and AM/PM fields.
View by date
1. Select Menu > Tools & Games > Scheduler
–
Scroll up or down to change hour,
minute and AM/PM.
and one of the following:
Press OK to save time and move to the
next field.
–
View Month to see the current month.
Days with events are highlighted. Scroll
through the calendar and press OK to
select a date.
6. At the Duration field, press OK to change
the duration.
–
Scroll left or right to move between hour
and minute fields.
–
–
View Day to see the current date. Scroll
right or left to move to another date.
Go to Date to select a specific date.
Scroll left or right to move between
month, day, and year fields. Scroll up or
down to change month, day, and year.
Press OK to select the date.
–
Scroll up or down to change hour
and minute.
Press OK to save duration and move to the
next field.
7. At the Priority field, press OK and select a
priority from the list.
2. At the day view, do one of the following:
8. At the Reminder field, press OK and select a
–
–
–
–
–
Highlight an existing event and press the
OK key to view the event detail.
Highlight a time and select Add New to
create a new event.
Select Options > Go to Today to return
to the current date.
Select Options > Go to Date to select a
specific date.
Select Options > Erase all Events to
erase all event for that date.
reminder from the list.
9. At the Reminder Sound field, press OK and
select a reminder sound from the list.
10. At the Silent Mode field, press OK and select
a Silent Mode setting.
11. At the Recurring Event field, press OK and
select an option from the list.
12. Select Save.
50
Scheduler
•
•
•
•
Priority to select the priority given to
new events.
Reminder to select the reminder given to
new events.
Reminder Sound to select the sound alert
given to new event reminders.
Silent Mode to select whether phone is in
silent mode during the duration of new events.
View by list
1. Select Menu > Tools & Games >
Scheduler > View All Events.
2. At the event list, highlight a event.
3. Select View to see the event detail or one the
of the following:
–
–
–
Select Options > Sort by Time to sort
events by time.
Select Options > Sort by Type to sort
events by type.
Select Options > Sort by Priority to sort
events by priority.
Alarm Clock
You can set up to four alerts with your phone’s
three alarm clocks and one quick alarm.
Note: The alert occurs only if the phone is on.
Modify an event
Use alarm clocks
1. Select Menu > Tools & Games >
Alarm Clock.
2. Highlight one of the alarms and select Set.
3. At the Time field, press OK to change the time.
You can modify existing events. From the event
detail screen, you can select OK to return to the
previous screen or Options and one the
following:
•
•
•
Edit to change the event.
Erase to erase the event.
Send to create a text message containing the
event.
–
Scroll left or right to move between hour,
minute and AM/PM fields.
–
Scroll up or down to change hour, minute
and AM/PM.
•
Copy to copy the event.
Press OK to save time and move to the
next field.
4. At the Alarm Sound field, press OK and select
a sound from the list.
5. At the Recurring Alarm field, press OK and
select an option from the list.
6. At the Note field, enter a note and press OK.
7. Select Save.
Scheduler settings
You can change the default settings of your
scheduler. Select Menu > Tools & Games >
Scheduler > Settings and one the following:
•
•
Scheduler Hours to change the work day.
Auto Delete to select when events are
automatically deleted.
User Guide
51
When the alarm rings, select Off to turn off the
alarm or Snooze to silence the alarm for
10 minutes.
Calculator
Use the calculator for basic mathematical equations.
1. Select Menu > Tools & Games >
Tip: Opening the flip turns off the alarm.
Calculator.
2. Enter the first number.
Use quick alarm
1. Select Menu > Tools & Games >
3. Use the Navigation key to select
mathematical operation.
Alarm Clock.
–
–
–
–
Press left to multiply.
Press right to divide.
Press up to add.
2. Highlight the quick alarm and select Set.
3. At the Time field, select a time option. A
notification shows the quick alarm is on.
Press down to subtract.
When the quick alarm rings, select Off to turn off
the alarm or Reset to set the quick alarm again.
4. Enter the second number and press OK to
get the result.
Tip Calculator
5. Select Exit to return to menu or Options and
one of the following:
The tip calculator helps you calculate how much
tip to include with a bill.
–
–
–
M+ adds the displayed result to the value
stored in memory.
MR displays the currently stored value on
the screen.
MC clears the currently stored value in
memory.
1. Select Menu > Tools & Games >
Tip Calculator.
2. Enter the amount of your bill and select
Next.
3. Select the percentage amount to tip. The new
bill amount is shown.
4. Select Done to return to menu or Split to
split the bill. To split the bill, enter the
number of guests and select Next. The phone
shows the amount each guest pays. Select
Done to return to menu.
52
Tip Calculator
Timer
Stopwatch
The timer counts down for the specified time and
beeps when that amount of time has elapsed.
The stopwatch counts time for you.
1. Select Menu > Tools & Games >
1. Select Menu > Tools & Games >
Stopwatch.
Timer > Set.
2. To work the stopwatch, select the
2. At the Set Timer, enter the time length.
following options:
–
–
–
Start to begin counting.
Stop to pause counting.
Reset to clear the stopwatch.
–
Scroll left or right to move between
hours, minutes and seconds fields.
Scroll up or down to change hours,
minutes and seconds.
–
Press the Back key to return to the menu.
3. If need, select Sound and one of the sounds
to change the sound.
Flashlight
4. To work the timer, select the
You phone comes with a flashlight. Select Menu >
Tools & Games > Flashlight > Turn On or Turn
Off to activate or deactivate the light, which stays
on until you turn it off.
following options:
–
–
–
Start to begin the countdown.
Stop to pause the countdown.
Reset to clear the timer.
Note: You can also press and hold the Back key
to turn on the flashlight. Once you release the
Back key, the flashlight turns off.
When the countdown is complete select Off to
silence the alarm.
User Guide
53
13 SETTINGS
Menu options
The contents of the Settings menu are as follows:
Sounds
Silent Mode
Volume
Ringers
Flip Sounds
Pwr On/Off Sound
Keypad
Display
My Banner
Accessories
Headset Ringing
Auto-Answer
Pwr Backlighting
Com Port Speed
TTY Device
Security
Lock Phone
Limit Calls
New Lock Code
Erase Contacts
Emergency Numbers
Main Menu View
Color Themes
Wallpaper
Screensaver
Backlighting
Auto-Hyphen
Language
Time/Date Format
Brightness
My Phone
Keyguard
T-coil Hearing Aid
Network
Alerts
Minute Alert
Message Alert
Page Alert
Voicemail Alert
Missed Call Alert
Data/Fax Calls
Privacy Alert
Roam/Svc Alert
Roam Option
Set Phone Line
Digital
Convenience
Voice Features
Location
Web Alert
Roam Call Alert
Auto Redial
Note: Some features may not be available. Check with your service provider.
54
Menu options
Volume
Sounds
Your phone has several settings for sound control.
You can select from a variety of ringers and
control the volume.
Ringer, Speakerphone, Earpiece, and Key
To adjust the volume of the ringer, speakerphone,
earpiece, or key:
1. Select Menu > Settings > Sounds >
Volume > Ringer Volume, Spkrphone
Volume, Earpiece Volume, or Key Volume.
Silent Mode
Your phone is set to make sounds when you
receive calls, press keys, navigate through menus,
and receive alerts (such as new messages). You
can silence all sounds and set the phone to vibrate
or light up when you receive calls and alerts.
Select Menu > Settings > Sounds > Silent Mode
and one of the following:
2. Scroll right to increase the volume, or left to
decrease the volume.
3. Select Save.
Smart Sound
To automatically adjust the volume during a call
based on surrounding noise levels, select Menu >
Settings > Sounds > Volume > Smart Sound >
Enabled.
•
Vibrate Only: The phone vibrates for the
duration of the incoming call or other alerts.
•
Vibe then Ring: The phone vibrates for the
first 10 seconds and then rings for the
remainder of the incoming call alert.
Lights Only: The phone lights up for the
duration of the incoming call or other alerts.
Normal Sounds: The phone rings for the
incoming call or alert (in effect, returns
phone to a non-silent mode).
Ringers
•
•
Type, Business, or Personal
You can choose the ringer type for incoming calls
and assign a ringer to contacts in your personal
or business group. Select Menu > Settings >
Sounds > Ringers > Ringer Type, Business
Ringer, or Personal Ringer and a ringer. You
can hear the ringers as you scroll down the list.
Note: The phone rings when attached to an
external power source (such as a charger), even
if all sounds have been silenced.
Roam Ringer
Your phone alerts you to roaming calls with a
specific ringer. Select Menu > Settings >
Sounds > Ringers > Roam Ringer > Enabled.
User Guide
55
Flip Open or Closed Sound
Other alerts
To set your phone’s sound tones when its flip
opens or closes, select Menu > Settings >
Sounds > Flip Sounds > Flip Open or
Flip Closed and a sound. You can hear the
sounds as you scroll down the list.
To choose how to be alerted of voicemail, pages,
text messages or missed calls, select Menu >
Settings > Alerts > Message Alert, Page Alert,
Voicemail Alert, or Missed Call Alert and one of
the following:
•
•
Disabled turns off the sound alert.
Power on/off sound
Vibrate, Beep, Freeway, Game, Bloop,
Winner, or Zilofon sets the phone to alert you
once when a new message is received.
Vibrate & Remind, Beep & Remind,
Freeway & Remind, Game & Remind,
Bloop & Remind, Winner & Remind, or
Zilofon & Remind sets the phone to notify
you once when a new message is received and
then notify you again every five minutes. To
stop a reminder alert, select Ignore.
You can set your phone to play a sound when
powering on or off. Select Menu > Settings >
Sounds > Power On/Off Sound > Enabled.
•
Keypad
Key Sound
To choose the sound the phone makes when you
press its keys, select Menu > Settings >
Sounds > Keypad > Key Sound > Tone, Click,
or Off.
Display
Key Length
My Banner
To control the length of the keypad tones, select
Menu > Settings > Sounds > Keypad >
Key Length > Normal or Long.
The banner is the personal label for your phone.
It appears on the home screen above the time and
date. The banner can be up to 14 characters long.
To change your banner:
Alerts
1. Select Menu > Settings > Display >
Minute Alert
My Banner.
Your phone can alert you with a short beep ten
seconds before each minute passes during a call.
Select Menu > Settings > Alerts >
2. Select Edit and press the Back key to clear
the current banner.
3. Enter your new text and select Save.
Minute Alert > Enabled.
56
Alerts
Main Menu View
Screen saver
To select a menu style, select Menu > Settings >
Display > Main Menu View and one of the
following:
Screen savers appear on the home screen when
the flip is open or closed. A screen saver activates
10 seconds after the last keypress. Incoming calls
and alerts override the screen savers. Select
Menu > Settings > Display > Screensaver and
one of the following options:
•
Graphic displays icons of each menu item,
with its name at the bottom of the screen.
List displays a list of each menu item.
•
•
Scroll to highlight a screen saver, press the
OK key, and select Assign to select a
screen saver.
The next time you select Menu from the home
screen, your selected menu style appears.
Color Themes
•
•
•
Select Options > Camera Pictures to select
an existing picture.
Select Options > Images to select an image
from your images folder.
Select Options > Take Picture to take a
new picture.
You can select a color theme for the display
background of your phone. Select Menu >
Settings > Display > Color Themes and a color
theme. You can preview the themes as you scroll
down the list.
Follow the prompts to save your selection.
Wallpaper
You can select a wallpaper for your phone’s home
screen. Select Menu > Settings > Display >
Wallpaper and one of the following options:
Backlighting
Your screen lights up while you are in a call or
when you press a key on the keypad. The
backlight automatically turns off when the phone
is inactive.
•
•
•
•
Scroll to highlight a wallpaper, press the OK
key, and select Assign to select a wallpaper.
Select Options > Take Picture to take a
new picture.
Select Options > Camera Pictures to select
an existing picture.
Backlight duration
You can set the length of time that bright
backlighting remains on. Select Menu >
Settings > Display > Backlighting > Duration
and one of the following:
Select Options > Images to select an image
from your images folder.
•
Disabled turns backlighting off.
Follow the prompts to save your selection.
User Guide
57
•
•
7 seconds, 15 seconds, or 30 seconds turns
backlighting on for the set time after your
last keypress.
7 sec. & in call, 15 sec. & in call, or 30 sec.
& in call turns backlighting on for the
duration of a call, and for the set time after
your last keypress.
Time and date format
Your phone can display different time/date
formats. Select Menu > Settings > Display >
Time/Date Format and a format.
Brightness
To change the brightness of the display:
Note: The “in call” settings drain the battery
more quickly.
1. Select Menu > Settings > Display >
Brightness.
2. Scroll to change the brightness.
Power save mode
3. Select Save.
You can conserve battery life by activating power
save mode to dim the backlight. The power save
mode sets the backlight to the lowest level. Select
Menu > Settings > Display > Backlighting >
Pwr Save Mode > On.
My Phone
Keyguard
Lock the keyguard
Auto-Hyphen
The keyguard locks the external number keypad
on your phone to prevent accidental keypresses
when the phone is turned on and a call is not in
progress. You can still answer or silence an
incoming call.
Auto-hyphenation, when enabled, automatically
inserts hyphens into your phone numbers to be
consistent with the U.S. dialing plan, such as
1-222-333-4444. Select Menu > Settings >
Display > Auto-Hyphen > Enabled.
•
To lock the keypad, press and hold the
* Shift key.
Language
•
To unlock the keypad, select Keyguard and
press the OK key.
Your phone can display alternative languages.
Select Menu > Settings > Display > Language
and a language.
Set the keyguard
You can set the phone to lock the keypad
automatically when the flip is closed. Select
Menu > Settings > My Phone > Keyguard >
Guard on Close.
58
My Phone
With Fast Find enabled, you can press one or two
keys to view close matches of the number you are
looking for.
Convenience
You phone provides you with settings that may
make your phone more convenient to use.
1. With the number keypad, from the home
screen, press the keys corresponding to the
letters of the name you want to find. A
matching contact or speed dial entry
appears.
Airplane Mode
While in an airplane, it is normally required that
you turn off your mobile phone because it emits
RF signals that interfere with air traffic control.
In Airplane Mode, however, your phone does not
emit RF signals. You cannot make or receive calls,
send text messages, use the Web, or Bluetooth
Wireless Connectivity but you can play games, use
the Scheduler, set the clock, and make emergency
calls to designated emergency numbers.
2. Highlight the contact you want and press the
Call key to call the number.
Frequent List
To enable frequent list, select Menu > Settings >
My Phone > Convenience > Frequent List >
Enabled.
Please check with uniformed personnel before
operating your phone in Airplane Mode.
From the home screen, select Contacts. With the
Frequent List enabled, the last 15 contacts of your
most frequently called contacts appear. Scroll past
the double line to view the entire contacts list.
To set your phone to Airplane Mode, select
Menu > Settings > My Phone > Convenience >
Airplane Mode > OK > Enabled. Follow the
prompts to complete enabling the Airplane Mode.
Hold Call
With the hold call feature, you can place incoming
calls on hold until you are ready to answer them.
Open to answer
You can open the flip of your phone to answer a
call. Select Menu > Settings > My Phone >
Convenience > Open to answer > Enabled.
Note: The hold call feature does not work with
the Open to Answer feature enabled.
See “Open to answer” on page 59.
Fast Find
To use fast find, select Menu > Settings >
My Phone > Convenience > Fast Find >
Enabled.
User Guide
59
Enable hold call feature
Change the hold message
1. Select Menu > Settings > My Phone >
Convenience > Hold Call > Re-Record
Msg.
1. Select Menu > Settings > My Phone >
Convenience > Hold Call > Enabled or
Re-Record Msg (to record a new hold
call message). With no hold message
recorded, the phone prompts you to record
one, such as “Please hold. I’ll answer in
a minute.”
2. Record the message twice, as prompted.
3. Select Save to save the message or Options
and one of the following.
–
–
Play to replay your message.
Re-Record to record your message
again.
2. Record the message twice, as prompted.
3. Select Save to save the message or Options
and one of the following.
–
Exit to exit.
–
–
Play to replay your message.
Re-Record to record your message
again.
1-Touch Dialing
The 1-Touch Dialing feature is the fastest way to
speed dial a contact that has a speed dial location.
To use 1-Touch Dialing, you must enable 1-Touch
Dialing on your phone and have a speed dial
location assigned to a contact.
–
Exit to exit.
The next time a call comes in, you can place it
on hold.
Place a call on hold
You can place a call on hold once you have
enabled the Hold Call feature.
To enable 1-touch dialing, select Menu >
Settings > My Phone > Convenience >
1-Touch Dialing > Enabled.
Note: If you are already on a call and you receive
another call, you cannot place the incoming call
on hold. With no call waiting enabled, the call
goes to voicemail instead.
To call a contact that has a speed dial location,
press and hold the speed dialing number.
Note: If it is a two-digit number, press the first
digit briefly, then press and hold the second digit.
For example, if the speed dialing location is 15,
press 1 briefly, then press and hold 5.
When a call comes in:
1. Select Hold Call. The caller is placed on
hold and then hear your recorded hold
message.
Voice Features
The following features enable you to customize
the voice commands.
2. Select Answer to speak to the caller on hold
or End Call to hang up without speaking.
60
My Phone
Enable voice wake-up
Add Voice Dial
Select Menu > Settings > My Phone >
Voice Features > Voice Wake-Up >
With accessory to enable calls with an accessory.
You can add a new voice dial to your phone.
1. Select Menu > Settings > My Phone >
Voice Features > Add Voice Dial.
Use voice wake-up
To wake up the phone:
2. At the voice prompt, say a name.
3. At the voice prompt, repeat the name.
4. Select one of the following:
1. Say “Wake Up” and listen for a tone.
2. Say “Wake Up” again until you hear two
–
–
Add New creates a new contact.
Add to existing adds the voice tag to an
existing contact.
tones.
If the phone does not recognize your Wake Up
command, see “Voice Training” on page 61.
Erase Voice Dial
Voice Answer
You can set your phone to answer a call
automatically when using a hands-free accessory.
You can erase all existing voice dial tags from
your phone. Select Menu > Settings >
My Phone > Voice Features >
Erase Voice Dial > Yes.
Enable voice answer
Select Menu > Settings > My Phone > Voice
Features > Voice Answer > Enabled to enable
answering calls with an accessory.
Voice Training
If you phone is having trouble recognizing your
voice, you can train with the Yes, No, and Wake up
commands. Select Menu > Settings >
My Phone > Voice Features > Voice Training >
OK > Train All or the item you want to train.
Follow the prompts for each word until training
is complete.
To use the voice answer feature, you must have
the Auto-Answer feature (see “Auto-Answer” on
page 62) disabled and the phone set to Normal
Sounds (see “Silent Mode” on page 55).
Use voice answer
When you receive an incoming call, the phone
prompts “Incoming call, answer?” or “Incoming
roam call, answer?” If the caller is recognized as a
contact entry in your phone, the phone prompts
“Incoming call from (Name), answer?” Say “Yes”
or press any key except the End key to answer.
Voice Wake-Up
You can set your phone to make a call using a
hands-free accessory.
Note: Voice Wake-up does not work with
keyguard active.
User Guide
61
Say “No” and press the End key to silence the
alert. Remain silent. The voice alert repeats twice
and the phone rings once, then returns to the
home screen.
Headset Ringing
With a headset attached to your phone, the ringer
can be played through the headset or phone
speaker. Select Menu > Settings >
Accessories > Headset Ringing and one of
the following:
Expert Mode
With the expert mode enabled, instead of
speaking a command following the initial voice
prompts, you can speak the command after you
hear a tone. Select Menu > Settings >
My Phone > Voice Features > Expert Mode and
one of the following:
•
•
Out of phone rings from the phone speaker.
Out of headset rings from the headset.
Auto-Answer
With a headset or hands-free car kit attached,
your phone can be set to answer automatically.
Select Menu > Settings > Accessories >
Auto-Answer > After 5 seconds to set the phone
to automatically answer after 5 seconds.
•
•
Normal sets phone to default voice prompts.
Expert sets phone to sound tones instead of
voice prompts.
Phone information
Power backlighting
You can access information regarding your
phone. Select Menu > Phone Info and one of
the following:
You can set backlighting to remain on when an
external power source, such as the AC adapter, is
used with the phone.
•
Build Info shows specific software and
Note: Power backlighting may not be available
with the optional desktop charger or other
accessories. The battery charges more slowly with
power backlighting on.
hardware information for your phone.
•
Icon Keys shows the icons used by
your phone.
Select Menu > Settings > Accessories >
Pwr Backlighting > Normal or Always On.
Accessories
This section describes settings that affect
accessories you use with your phone.
Tip: Use the power backlighting as a night light
when traveling.
62
Accessories
Com Port Speed
Network
The Com Port Speed sets the data rate at which
your phone connects to a laptop or PC, or at
which it sends and receives over-the-air text
messages. Select Menu > Settings >
Accessories > Com Port Speed and your
desired speed.
Data and fax calls
Your phone may be able to receive certain data or
faxes, depending on the system sending the
information. You cannot receive voice calls while
the phone is in data/fax mode.
To receive data or faxes, you must connect the
phone to a laptop or PC and switch the phone
from voice mode to data/fax mode.
There may be a higher charge for making calls
using high-speed data in areas where 1X service
is available. Check with your service provider
for details.
Note: To purchase a cable,
TTY Device
You can connect the phone to a TTY device for the
hearing impaired.
To enable data/fax mode, select Menu >
Settings > Network > Data/Fax Calls and one of
the following:
Note: Enable TTY only when using the phone with
a TTY device.
•
•
Voice Only turns data/fax mode off.
Fax, next call or Data, next call sets the
phone to data/fax mode for the next incoming
call or the next ten minutes.
Fax, until off or Data, until off sets the
phone to data/fax mode until the phone is
turned off.
1. Connect the TTY device to the phone.
2. Select Menu > Settings > Accessories >
TTY Device (or enter ##889 from the home
screen and select TTY) > OK > TTY On.
•
T-coil Hearing Aid
Privacy Alert
You can use your phone with a T-coil Hearing Aid
device. Select Settings > Accessories >
T-coil Hearing Aid > OK > Enabled.
You can set your phone to alert you when
enhanced digital CDMA privacy is lost or
regained. Select Menu > Settings > Network >
Privacy Alert > Enabled.
Note: Enable T-coil Hearing Aid only when using
the phone with a T-coil Hearing Aid device.
User Guide
63
When you are using one line, you cannot receive
calls from the other. It would be as if the phone
were “off” for that number. Your voicemail,
however, still takes messages. All contacts and
settings are shared for both lines.
Roaming alert
Use this setting if you want the phone to alert you
when roaming outside of your home service area.
Select Menu > Settings > Network >
Roam/Svc Alert and one of the following:
Note: You must first establish a second phone
line with your service provider. Once established,
a second phone number becomes available in the
menu for selection.
•
•
Disabled turns the roaming alert off.
When no svc alerts you with three tones
decreasing in pitch when service is lost and
three tones increasing in pitch when service is
acquired again.
On roam change alerts you with two
decreasing tones when roaming service is
acquired and three increasing tones when
home area service is acquired again.
On any change alerts you with three
increasing tones if there is a change in
roaming service or three decreasing tones if
the phone loses service.
Control network roaming
•
•
Depending on services available from your service
provider, you may set the phone to either digital
or analog mode. This is useful if you are in an
area that borders on digital service and the
automatic feature is causing the phone to keep
switching between modes.
Select Menu > Settings > Network > Digital and
one of the following:
•
Automatic automatically switches the phone
between digital and analog.
Digital only sets the phone to work in digital
mode only.
Roam Option
You can restrict your phone from making a call
when roaming. Select Menu > Settings >
Network > Roam Option > Automatic (to allow
roaming calls) or No roaming (to disallow
roaming calls).
•
Location
Use this setting to share your location information
with network services other than emergency
services (for example, 911, 111, 999 and 000) in
markets where service has been implemented.
Set Phone Line
Your phone can have two service accounts, or
phone lines, associated with it. Each phone line
has its own phone number. Select Menu >
Settings > Network > Set Phone Line and one
of the two lines.
64
Network
Select Menu > Settings > Network > Location
Note: Roam call alert is disabled when the phone
and one of the following:
is in Emergency Mode.
•
911 Only (default) shares your position
information only with emergency services
when you call your 3-digit emergency code.
Location On shares your position
information, in addition to
Auto Redial
You can set your phone to repeat a call when the
called number is busy or there is no answer.
Select Menu > Settings > Network > Auto
Redial > Enabled.
•
emergency services.
Note: This feature works only when your phone
is in digital mode. You cannot turn off the locator
to emergency services.
Security
This section describes all the features involved in
securing your phone and preventing access to
personal information. All security features are
shielded by a four-digit lock code.
Web Alert
You can set a prompt to confirm the start or exit
of the Web Browser.
Lock Phone
Select Menu > Settings > Network > Web Alert
and one of the following:
When your phone is locked, you can call only
emergency numbers or your service provider’s
customer service number. You can still receive
incoming calls.
•
•
•
•
At Start prompts when you start a session.
At End prompts when you end a session.
Both prompts when you start or end a session.
No Prompts sets no prompts.
1. Select Menu > Settings > Security.
2. Enter your four-digit lock code.
3. Select Lock Phone and one of the following:
Roam Call Alert
–
–
Never leaves the phone always unlocked.
On power up locks the phone every time
you turn it on.
You can set the phone to warn you before you
answer or place a call while roaming. Select
Menu > Settings > Network > Roam Call
Alert > Call Prompt to turn on the call guard.
The phone emits a distinctive ring to indicate
when you are roaming during a call.
–
Now locks the phone immediately.
To unlock the phone:
1. From the home screen, select Unlock.
2. Enter your four-digit lock code.
To accept or place a call while roaming, you
must press 1.
User Guide
65
Limit Calls
Emergency Numbers
You can limit the calls that can be made from your
phone to emergency numbers, your contacts, and
your service provider’s numbers.
The emergency numbers feature allows you to
specify three personal phone numbers that can be
called when the phone is locked.
1. Select Menu > Settings > Security.
2. Enter your four-digit lock code.
1. Select Menu > Settings > Security.
2. Enter your four-digit lock code.
3. Select Emergency Numbers.
4. Select an Unassigned slot.
3. Select Limit Calls and one of the following:
–
–
No Limit: limits no calls.
Limit Outgoing limits outgoing calls.
Incoming calls can be answered.
Limit All limits both incoming and
outgoing calls.
5. Enter the phone number, including the area
code. Do not enter 1 before the area code.
–
6. Select Done.
You can view these numbers only when entering
them for the first time. To make a call to an
emergency number from a locked phone, you
must dial the number (including area code)
exactly as it is stored in Emergency Numbers.
New Lock Code
Change your lock code from the default provided
by the service provider. The lock code is typically
0000 or the last 4 digits of your phone number.
1. Select Menu > Settings > Security.
2. Enter your four-digit lock code.
3. Select New Lock Code > Yes.
4. Enter a new four-digit code.
5. Re-enter your new lock code.
The lock is now changed.
Erase Contacts
You can erase all entries from your contacts list.
1. Select Menu > Settings > Security.
2. Enter your four-digit lock code.
3. Select Erase Contacts > Yes > Yes.
66
Security
®
14 BLUETOOTH WIRELESS TECHNOLOGY
The Bluetooth® wireless technology on your
phone enables wireless connectivity with
accessories such as portable or installed hands-
free car kits, headsets, handsets, computers, PC
cards and adapters, PDAs, and speakers. Not
available on all phones. For details check with
your service provider.
•
Off prohibits your phone from being used
with any Bluetooth wireless technology device.
To prolong battery life, it is recommended to
set Bluetooth to Off when you are not using it.
When you turn Bluetooth On the first time, you
are prompted to do a device search. Then you can
pair with a device.
You must use a Bluetooth wireless technology
device (compatible with Class 2 Bluetooth
wireless technology, version 1.2) in order to use
this phone wirelessly. Bluetooth wireless
Pairing
You must first “pair” your phone with the
Bluetooth wireless technology enabled device to
allow your phone to communicate with it. Refer to
the following instructions for setting up Bluetooth
wireless technology in conjunction with the user
guide provided with your Bluetooth wireless
technology device.
technology accessories have the
symbol. For
additional information on carrier-supported
profiles and third-party accessory compatibility
for Bluetooth wireless technology, visit
1. Select Menu > Bluetooth > On/Off >
Turning Bluetooth on
On Visible or On Invisible.
You must turn on your phone’s Bluetooth feature
to use it with Bluetooth wireless technology
devices. Select Menu > Bluetooth > On/Off and
one of the following:
2. Prepare the Bluetooth wireless technology
device (Bluetooth accessory) for pairing as
described in the other device’s user guide.
3. Select Menu > Bluetooth > My Devices >
Find New. Your phone then searches and
detects visible Bluetooth wireless technology
enabled devices in the vicinity.
•
On Visible allows other devices to find
your phone.
•
On Invisible hides your phone for all devices
except those listed in your My Devices.
4. With devices found, select Add to see the list.
5. Highlight your desired device and select Add.
User Guide
67
Note: When pairing is initiated from another
Bluetooth wireless technology device, you
are prompted to accept or reject the pairing.
Device list options
You can change or review the information about
each device you paired with your phone.
6. If necessary, enter the password provided in
the Bluetooth wireless technology device’s
user guide and select OK.
1. Select Menu > Bluetooth > My Devices.
2. Highlight your desired device.
3. Select Options and one of the following:
Your phone waits for the device’s response.
With the password accepted, the device
shows in My Devices.
–
–
Rename to rename the device.
Delete to remove the device from your
phone if you are no longer going to use
it.
Using Bluetooth
–
Services to view a description of the
device (such as Headset, Handsfree,
Object Push, and Serial Port).
Before you can use the Bluetooth wireless
technology functions of your phone, you must get
your phone ready to communicate with a device.
This is called “connecting.”
Bluetooth settings
Connecting to a device
To connect your phone to an audio Bluetooth
wireless technology device:
You can set how your phone interacts with
Bluetooth wireless technology devices. Select
Menu > Bluetooth > Settings and one of
the following:
1. Select Menu > Bluetooth > My Devices.
•
•
•
My Name changes the name of your phone for
other devices it is paired with to identify.
Visible Duration sets the time your phone
remains visible to other devices.
Services shows the list of the Bluetooth
wireless technology service protocol
supported by your phone.
2. At the device list, highlight a device and
select Connect.
A notification appears confirming the connection.
You can now use the device with your phone.
Disconnecting from a device
To disconnect your phone from an audio
Bluetooth wireless technology device:
1. Select Menu > Bluetooth > My Devices.
2. At the device list, highlight a device and
select Disconnect.
68
Using Bluetooth
15 VOICE RECOGNITION
With voice features, you can call a contact, dial a
phone number, access menus, or find contact
information from your voice dial list using
voice recognition.
Voice commands
With voice commands, you speak your commands
into the phone’s microphone.
Start voice commands
Note: You cannot use voice recognition to end a
call; you must press the End key.
1. Press the Call key to initiate voice
commands. The phone prompts, “Say a
name or say dial”.
Voice dial list
To call or find a contact using voice dial you must
add the contact to your voice dial list. The contact
name must not have more than three words or
components for voice dialing recognition.
2. Say one of the following commands and
follow the voice prompts.
–
“Say a name” to call a contact on your
voice dial list.
–
“Dial” to speak the digits of the phone
number.
Add a voice tag
You can add a voice dial tag to your phone. See
“Add Voice Dial” on page 61.
3. Press the Call key again to exit and go to the
Recent calls list.
Edit a voice tag
Call a contact
To edit existing voice dial tags:
1. Select Menu > Contacts > Voice Dial List.
2. Select your desired contact.
Before calling a person, you need to add the
contact name to the Voice Dial List.
See “Add Voice Dial” on page 61.
3. Highlight the number with a voice tag and
select Options > Add Voice Dial,
1. From the home screen, press the Call key.
The phone prompts, “Say a name”.
Edit Voice Dial or Erase Voice Dial.
2. Say the name of the person you want to call.
4. Follow the prompts.
If the name you said matches a contact in the
Voice Dial List, the phone responds: “Calling
(Name).” Remain silent to make the call, or
say “No” to cancel.
User Guide
69
If the phone finds multiple voice tags that
sound like the name you said, the phone lists
the names and asks you to verify which name
you want to call. Say “Yes” when you hear the
correct name. Say “No” when you hear an
incorrect name.
–
–
Say “Call” to dial the number.
Say “Verify” to cause phone to repeat the
set of digits you input.
Say “Cancel” to exit voice recognizer and
return to the home screen.
Speak a digit to enter the next digit. Once
the phone repeats the digit, you can
speak the next digit or pause to hear the
prompt.
–
–
3. Press the End key to end the call.
Call Using Digit Dial
When using digit dialing, you speak digits to dial a
phone number.
4. Press the End key to end the call.
Note: You cannot speak a string of digits. You
must speak one digit at a time and wait for
the prompt.
Voice Command Settings
To customize the voice commands,
see “Voice Features” on page 60.
1. From the home screen, press the Call key.
The phone prompts, “Say a name or say
dial”.
2. Say “Dial”. The phone responds “Speak
a digit”.
3. Speak the first digit of the phone number you
want to call. Once the phone repeats the
digit, you can speak the next digit.
If you pause, the phone prompts you with
one of the following options. After the
prompt, speak an option:
–
Say “Clear” to erase the last digit entered.
The phone responds: “Digit cleared.” To
clear the entire phone number, say
“Clear” again. When the phone prompts
you with “Clear entire phone number?”,
say “Yes” to clear or “No” to cancel.
70
Voice Command Settings
16 GETTING HELP
Customer Support
India: Toll fee#: 1-600-121214
Toll#: 0124-284-5000
Your service provider’s customer support
department may be accessible directly from your
phone when you dial a number, such as *611
(check with your service provider). They can
answer questions about your phone, phone bill,
call coverage area, and specific features available
to you, such as call forwarding or voicemail.
Mexico: 001-866-650-5103
New Zealand: 0-800-990-100
Panama: 001-800-51-934
Puerto Rico: 1-866-664-6443
Venezuela 0-800-100-2640
For questions about the phone features, refer to
the materials provided with your phone, or visit
Before requesting support, please try to
reproduce and isolate the problem. When you
contact the Customer Care Center, be ready to
provide the following information:
For additional questions, you may contact the
Kyocera Wireless Corp. Customer Care Center in
any of the following ways:
•
•
The name of your service provider.
The actual error message or problem you
are experiencing.
The steps you took to reproduce the problem.
The phone’s electronic serial number (ESN).
•
•
•
Email: [email protected].
Phone: 1-800-349-4478 (U.S. and Canada) or
1-858-882-1401.
•
•
Note: To locate the ESN, select Menu >
Phone Info > Build Info and scroll down to
the number.
•
Customer support phone numbers are also
available in the following countries:
Argentina: 0-800-666-0052
Australia: 1-800-507-000
Brazil: 0-800-55-2362
Chile: 800-43-1212
Qualified service
If the problem with your phone persists, return
the phone with all accessories and packaging to
the dealer for qualified service.
Colombia: 01-800-700-1546
User Guide
71
Phone accessories
To shop for phone accessories, visit
www.kyocera-wireless.com/store. You may also
call us at 800-349-4188 (U.S.A. only) or
858-882-1410.
Product evaluation
To participate in the testing and evaluation of
Kyocera Wireless Corp. products, including
cellular or PCS phones,
visit beta.kyocera-wireless.com.
72
Phone accessories
17 CONSUMER LIMITED WARRANTY
Kyocera Wireless Corp. (“KYOCERA”) offers you a
limited warranty that the enclosed product or
products (the “Product”) will be free from
defects in material and workmanship for a period
that expires one year from the date of sale of the
Product to you, provided that you are the original
end-user purchaser of the Product and provided
that your purchase was made from an authorized
supplier. Transfer or resale of a Product will
automatically terminate warranty coverage with
respect to that Product. This limited warranty is
not transferable to any third party, including but
not limited to any subsequent purchaser or owner
of the Product.
After the one year warranty period, you must pay
all shipping, parts and labor charges.
This limited warranty does not cover and is void
with respect to the following: (i) any Product
which has been improperly installed, repaired,
maintained or modified; (ii) any Product which
has been subjected to misuse (including any
Product used in conjunction with hardware
electrically or mechanically incompatible or used
with accessories not approved by KYOCERA),
abuse, accident, physical damage, abnormal
operation, improper handling, neglect, exposure
to fire, water or excessive moisture or dampness
or extreme changes in climate or temperature;
(iii) any Product operated outside published
maximum ratings; (iv) cosmetic damage; (v) any
Product on which warranty stickers or Product
serial numbers have been removed, altered, or
rendered illegible; (vi) cost of installation,
removal or reinstallation; (vii) signal reception
problems (unless caused by defects in material
and workmanship); (viii) damage the result of
fire, flood, acts of God or other acts which are not
the fault of KYOCERA and which the Product is not
specified to tolerate, including damage caused by
mishandling, shipping and blown fuses; (ix)
consumables (such as fuses); or (x) any Product
which has been opened, repaired, modified or
altered by anyone other than KYOCERA or a
KYOCERA authorized service center.
KYOCERA shall, at its sole and absolute discretion,
either repair or replace a Product (which unit
may use refurbished parts of similar quality and
functionality) if found by KYOCERA to be defective
in material or workmanship, or if KYOCERA
determines that it is unable to repair or replace
such Product, KYOCERA shall refund the purchase
price for such Product, provided that the subject
Product (i) is returned, with transportation
prepaid, to a KYOCERA authorized service center
within the one year warranty period, and (ii) is
accompanied by a proof of purchase in the form
of a bill of sale or receipted invoice which
evidences that the subject Product is within the
one year warranty period (“Proof of Purchase”).
User Guide
73
USE ONLY KYOCERA APPROVED ACCESSORIES
WITH KYOCERA PHONES. USE OF ANY
UNAUTHORIZED ACCESSORIES MAY BE
DANGEROUS AND WILL INVALIDATE THE PHONE
WARRANTY IF SAID ACCESSORIES CAUSE
DAMAGE OR A DEFECT TO THE PHONE.
STATUTORY OR OTHERWISE, WITH RESPECT TO
THE PRODUCTS, INCLUDING BUT NOT LIMITED
TO ANY IMPLIED WARRANTY OR CONDITION OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR AGAINST
INFRINGEMENT OR ANY IMPLIED WARRANTY OR
CONDITION ARISING OUT OF TRADE USAGE OR
OUT OF A COURSE OF DEALING OR COURSE OF
PERFORMANCE. NO DEALER, DISTRIBUTOR,
AGENT OR EMPLOYEE IS AUTHORIZED TO MAKE
ANY MODIFICATION OR ADDITION TO THIS
WARRANTY.
KYOCERA SPECIFICALLY DISCLAIMS LIABILITY
FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL,
GENERAL, PUNITIVE, EXEMPLARY, AGGRAVATED,
INCIDENTAL OR CONSEQUENTIAL DAMAGES,
EVEN IF ADVISED OF THE POSSIBILITY THEREOF,
WHETHER FORESEEABLE OR UNFORESEEABLE
OF ANY KIND WHATSOEVER, INCLUDING BUT
NOT LIMITED TO LOSS OF PROFITS,
UNANTICIPATED BENEFITS OR REVENUE,
ANTICIPATED PROFITS ARISING OUT OF USE OF
OR INABILITY TO USE ANY PRODUCT (FOR
EXAMPLE, WASTED AIRTIME CHARGES DUE TO
THE MALFUNCTION OF A PRODUCT) OR
Some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages,
or allow limitations on how long an implied
warranty lasts, so the above limitations or
exclusions may not apply to you. This limited
warranty gives you specific legal rights, and you
may also have other rights which vary from
jurisdiction to jurisdiction.
CONTRIBUTION OR INDEMNITY IN RESPECT OF
ANY CLAIM RELATED TO A PRODUCT.
For warranty service information, please call the
following telephone number from anywhere in the
continental United States and Canada:
1-800-349-4478 or 858-882-1401; or contact
KYOCERA at the following address: 10300 Campus
Point Drive, San Diego, California, 92121-1582,
USA, Attention: Technical Support.
REPAIR OR REPLACEMENT OF A DEFECTIVE
PRODUCT OR REFUND OF THE PURCHASE PRICE
RELATING TO A DEFECTIVE PRODUCT, AS
PROVIDED UNDER THIS WARRANTY, ARE YOUR
SOLE AND EXCLUSIVE REMEDIES FOR BREACH
OF THE LIMITED WARRANTY, AND SUBJECT TO
THIS WARRANTY, THE PRODUCTS ARE
APPROVED AND ACCEPTED BY YOU “AS IS”.
KYOCERA MAKES NO OTHER WARRANTIES,
REPRESENTATIONS OR CONDITIONS OF ANY
KIND, ORAL OR VERBAL, EXPRESS OR IMPLIED,
DO NOT RETURN YOUR PRODUCTS TO THE
ABOVE ADDRESS. Please call or write for the
location of the Kyocera Wireless Corp. authorized
service center nearest you and for procedures for
obtaining warranty service.
74
Product evaluation
INDEX
Numerics
1-touch dialing, 14, 60
caring, 2
indicators and icons, 45
LED, 45
charging, 1
installing, 1
recharging, 1
lens, 6
A
multiple pictures, 45
options, 44
resolution, 44
self timer, 44
settings, 44
accessory, 62, 72
add voice dial, 61
airplane mode, 59
alarm clock, 51
alert
Bluetooth, 67
connecting devices, 68
pairing, 67
settings, 68
turning on, 67
shutter sound, 45
taking picture, 44
white balance, 45
minute, 28, 56
missed call, 27
privacy, 63
BREW apps, 23
brick attack, 48
brightness, 45, 58
business ringer, 55
camera pictures
roam, 15
browsing, 46
capitalization, 18, 21
CC and BCC
showing or hiding, 42
color themes, 57
color tone, 45
roam call, 65
roaming, 64
C
voicemail, 15
calculator, 52
web, 26, 65
call
answering calls, 12
appended message, 39
auto receive mode
multimedia message, 37
auto redial, 65
auto retrieve, 42
auto-answer, 62
auto-hyphen, 58
Axcess Apps, 23
data and fax, 15, 63
emergency, 16
guard, 15
limit, 66
roaming, 15, 64
com port speed, 63
contacts, 29
adding, 29
adding extension, 30
adding to group, 31
adding voice tag, 31
changing voice tag, 31
editing, 29, 30
call history, 27
call list, 27
call log, 27
call timers, 28
callback number, 42
text message, 35
calls
B
email address, 31
erasing, 66
erasing voice tag, 31
note, 32
phone number type, 33
picture, 30, 32
primary number, 31
ringer, 30, 32
back cover, 6
lock, 1, 6
backlight, 57
power, 62
backlight duration, 57
banner, 56
battery
answering, 12
ending, 13
camera, 44
color tone, 45
flash, 6, 44
Phone User Guide
75
searching, 33
secret address, 31, 32
secret note, 32
secret numbers, 31
sending all, 29
sending as a vCard, 29
sending as vCard, 30, 33
sending picture message, 31
sending text message, 31
speed dial list, 31, 33
street address, 32
viewing all, 29
erase contacts, 66
erase voice dial, 61
evaluation
hearing aid, 63
help, getting, 71
hold call, 14, 59
product, 72
I
event
icon
adding, 49
phone, 62
changing, 51
checking, 50
expert mode, 62
eyelet, 6
text message, 35
icons, 8
images
browsing, 47
indicators and icons
camera, 45
F
fast find, 59
flash, 44
flashlight, 53
flight mode. See airplane mode, 59
flip close
sounds, 56
flip open
sounds, 56
folders, 46
format
time and date, 58
forward
text message, 35
frame, 45
frequent list, 59
voice dial list, 33
Web address, 31
K
key
convenience, 59
convention
frequently used, 7
navigation, 11
key length
sounds, 56
keyguard, 58
keypad
using this guide, 11
custom menu, 13
customer support, 71
D
data and fax call, 63
default text, 43
digital, 64
download, 23
downloading
application, 23
number, 3
QWERTY, 5
sounds, 56
L
languages, 58
LED, 45
left softkey, 11
limit calls, 66
location information, 64
lock
back cover, 1, 6
lock code
changing, 66
lock message, 35
multimedia message, 38
lock phone, 65
G
E
games, 48
downloading, 23
group list
creating, 40
earpiece, 13
email address
contacts, 31
emergency calls, 16
emergency numbers
security, 66
H
hard pause, 30
hardware information, 62
headset
emergency service
location information, 64
enhancement, 62
ringer, 62
76
M
saving picture, 38
sent, 40
making calls, 12
number extension, 30
overview, 3
main menu, 10
style, 57
making calls, 12
media gallery, 46
memory, 24
menu, 10
tips, 39
viewing, 38
viewing options, 38
turning on and off, 12
phone line
setting, 64
picture
multiple, 45
multishot, 45
custom, 13
settings, 54
style, 57
contacts, 33
multiple, 45
saving, 38
my banner, 56
N
navigation key, 11
network roaming, 64
new event
adding, 49
normal alpha mode, 18
picture message. See multimedia
message, 42
port speed, 63
power backlighting, 62
power save mode, 58
prepend, 31
primary number, 31
privacy alert, 63
prompt mode
Web, 25
message settings, 41
messages
multimedia message, 36
text message, 34
minute alert, 28, 56
missed call
note
contacts, 32
number
entering, 17, 20
number keypad, 3
entering text, 20
number type
alert, 27
MobileShop, 23
mode
multimedia message, 37
changing, 18, 21
entering text, 17
normal alpha, 18
numbers only, 20
rapid entry, 20
multimedia message
appended messages, 39
auto receive mode, 37
completing, 40
creating, 36
Q
QuickText
contacts, 33
numbers only mode, 20
editing, 41
text message, 35
QWERTY keypad, 3, 5
entering text, 17
O
open to answer, 59
outbox, 40
R
P
race 21, 48
pairing, 67
personal banner, 56
personal ringer, 55
phone
rapid entry mode, 20
receipt
erasing, 38
picture messages, 42
text messages, 42
receipt request
text message, 35
recent calls, 27
redial, 65
forwarding, 38
locking, 38
accessories, 72
icons, 62
information, 62
keypads, 3
locking, 65
options, 37
prompt mode, 37
receipt, 42
retrieving, 37
Phone User Guide
77
redialing, 12
reply
shutter sound, 45
signature, 41
silent mode, 51, 55
smart sound, 55
smiley
icon, 35
locking, 35
text message, 35
notification, 35
options, 34
priority, 35
receipt, 35, 42
replying, 35
retrieving, 35
saving, 35
saving as QuickText, 35
sender, 36
viewing, 35
resolution, 44
right softkey, 11
ringer
entering, 18
business, 55
contacts, 32
headset, 62
personal, 55
roam, 15, 55
type, 55
software information, 62
sounds
browsing, 47
flip close, 56
flip open, 56
keypad, 56
volume, 55
roam
keypad length, 56
power on or off, 56
reminder, 51
settings, 55
time pause, 30
timer, 53
tip calculator, 52
tools, 48
alert, 15
call alert, 65
options, 15, 64
ringer, 15, 55
roaming, 64
roaming alert, 64
roaming calls, 64
silence all, 55
speakerphone, 13
speed dial, 14
stopwatch, 53
style
main menu, 57
support, customer, 71
symbol
TTY
turning on and off, 12
using, 63
V
vCard
sending, 33
voice answer, 61
voice commands, 60, 69, 70
voice dial
S
scheduler, 49
settings, 51
screen icons, 8
screen saver, 57
security
emergency numbers, 66
settings, 65
settings
entering, 17, 18, 21
T
adding, 61, 69
T-coil hearing aid, 63
changing, 69
text
erasing, 61
changing mode, 18, 21
entering, 19
mode, 17
voice dial list, 69
voice memo
Bluetooth, 68
menu, 54
messages, 41
scheduler, 51
sounds, 55
volume, 55
recording, 48
reviewing, 49
voice recognition, 69
voice training, 61
voice wake-up, 61
voicemail, 15
number keypad, 20
QWERTY keypad, 17
text message
callback number, 35
creating, 34
forwarding, 35
78
alert, 15
number, 43
volume
adjusting, 14
auto adjust, 55
settings, 55
W
wallpaper, 57
web
alert, 26, 65
browser, 25
menu, 25
web address
contacts, 31
web apps, downloading, 23
white balance, 45
word
entering, 18, 20
Phone User Guide
79
Kyocera Wireless Corp.
10300 Campus Point Drive
San Diego, CA 92121 USA
82-G1934-1EN, Rev. 001
|