LAP24EULBA
LAP24EULFR
NOTEBOOK CART ASSEMBLY
WITH TIMER
Assembly Instructions for:
INTERIOR E-UNIT
REPOSITIONING / REPLACEMENT
AND
LAP24EULBA
CAUTION: RISK OF ELECTRICAL SHOCK.
DO NOT PLUG INTO ANOTHER
TIMER REPLACEMENT
RELOCATABLE POWER TAP.
Parts List
Qty.
1
Part No.
Description
NO TV/MONITOR TO BE
USED ON TOP OF CART
LAP24EULBA Cart Assembly, e-units at back
LAP24EULFR Cart Assembly, e-units at front
Tools Required
Philips screwdriver
MAXIMUM WEIGHT OF ACCESSORIES
ON TOP OF CART: 25 LBS.
The socket-outlet to be installed near the equipment and to be easliy
accessible.
Do not load each electrical unit with more than 12 A and do not load any
recepticle with more than 12 A.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM POWER
SOURCE BEFORE STARTING
LAP24EULFR
E-UNIT REPOSITIONING:
'FRONT TO REAR'
SEE DETAIL 'B'
bottom shelf
SEE DETAIL'A'
Step 1
Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefully unplug the power
cords of the E-Units from the timer assembly (see Front View) and unclip the power cords from the 4 clips located
at the bottom panel of the cart. Loosen the screw holding the E-Unit bracket assembly and remove all 4 bracket
assemblies (see DETAILS 'A' and 'B').
front-left
front-right
Step 2
Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf channel and set it aside.
Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf channel and set it aside.
DETAIL 'C'
Step 3
Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DETAIL'C').
mounting
tab
DETAIL 'D'
Step 4
Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D',
then carefully sliding out. Set each shelf aside.
cutout
window
clip-rear
Step 5
Reinstall the E-Units (set aside from being removed from the front) as follows:
1. Rotate the E-Unit 180 degrees (from original position).
2. Position to the rear of cart.
3. Tilt in and set bottom in back, in front of rear panel cutout window.
4. Grip the top and tilt to the upright position, underneath top panel bracket.
When repositioned correctly, the E-Unit power switch should be visible from rear panel cutout window.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the
bracket assembly) and tighten screws securely.
Plug in the E-Units power cords into the bottom outlets of the timer assembly.
Press each E-Unit power cord into the single wire clip located at the rear/bottom of the cart only.
Fold the power cords into a 'c' pattern loop on the bottom surface (see view in Step 6).
tab
notch
Step 6
Reinstall the 7 interior shelves as follows:
1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in all remaining shelves into position as the bottom shelf.
DETAIL 'E'
Step 7
Reinstall 14 screws to rear panel that will secure the 7 interior shelves
(see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS.
Installation is now complete and ready for use.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
E-UNIT REPOSITIONING:
'REAR TO FRONT'
DETAIL 'A'
Step 1
Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DETAIL'A').
mounting
tab
DETAIL 'B'
Step 2
With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting
tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside.
E-Unit power
cord
timer assembly
Front View
Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and unclip the power
cords from the clips at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove all 4
bracket assemblies (see DETAILS 'D' and 'E').
DETAIL 'D'
DETAIL 'E'
rear-left
rear-right
Step 3
Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf bracket and set it aside.
Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf bracket and set it aside.
notch
tab
Step 4
Reinstall the 7 interior shelves as follows:
1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in all remaining shelves into position as the bottom shelf.
DETAIL 'F
Step 5
Reinstall 14 screws to rear panel that will secure the 7 interior shelves
(see DETAIL 'F'). DO NOT OVER TIGHTEN SCREWS.
offset
clip
Step 6
Reinstall the E-Units (set aside from being removed from the rear) as follows:
1. Rotate the E-Unit 180 degrees (from original position).
2. Position to the front of cart.
3. Tilt in and set against offset of bottom panel (of cart).
4. Grip the top and tilt to the upright position.
When repositioned correctly, the E-Unit power switch should face the front.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the
bracket assembly) and tighten screws securely.
Plug in the E-Units power cords into the bottom outlets of the timer assembly.
Press each E-Unit power cord into the two wire clips located (in line, behind E-Unit) on the bottom of cart.
Installation is now complete and ready for use.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
E-UNIT REPLACEMENT:
'REAR LOCATION'
DETAIL 'A'
Step 1
Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DETAIL'A').
mounting
tab
DETAIL 'B'
Step 2
With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting
tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside.
E-Unit power
cord
timer assembly
Front View
Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and unclip the power
cord(s) from the clip(s) at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove
each bracket assembly (see DETAILS 'C' and 'D').
DETAIL 'C'
DETAIL 'D'
rear-left
rear-right
Step 3
Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf
bracket and set it aside.
cutout
window
clip
Step 4
Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top.
When repositioned correctly, the E-Unit(s) power switch should be visible from rear panel cutout window.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the
bracket assembly) and tighten screws securely.
Plug in the E-Unit(s) power cord(s) into the bottom outlet(s) of the timer assembly.
Press E-Unit power cord(s) into the wire clip(s) located at the rear/bottom of the cart.
Fold the power cords into a 'c' pattern, on the bottom surface (see view in Step 5).
tab
notch
Step 5
Reinstall the 7 interior shelves as follows:
1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in all remaining shelves into position as the bottom shelf.
DETAIL 'E'
Step 6
Reinstall 14 screws to rear panel that will secure the 7 interior shelves
(see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS.
Installation is now complete and ready for use.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
E-UNIT REPLACEMENT
'FRONT LOCATION'
SEE DETAIL 'B'
bottom shelf
SEE DETAIL 'A'
Step 1
Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power
cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the bottom of
cart. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s)
to be replaced (see DETAILS 'A' and 'B').
E-Unit power
cord
timer assembly
bottom shelf
Front View
bracket
assembly
clip
DETAIL 'B'
bracket
assembly
DETAIL 'A'
front-left
front-right
Step 2
Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf
channel and set it aside.
front-left
front-right
bottom shelf
Step 3
Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top.
When repositioned correctly, the E-Unit(s) power switch should face the front.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the
bracket assembly) and tighten screws securely.
Plug in the E-Unit power cord(s) into the bottom outlet(s) of the timer assembly (located underneath bottom
shelf).
Press E-Unit power cord(s) into the two wire clips located [in line, behind E-Unit(s)] on the bottom of cart.
Installation is now complete and ready for use.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
TIMER REPLACEMENT:
'E-UNIT AT REAR LOCATION'
DETAIL 'A'
Step 1
Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DETAIL'A').
mounting
tab
DETAIL 'B'
Step 2
With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from
mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside.
E-Unit power
cord
timer assembly
Front View
Carefully unplug the power cords of the E-Units from the timer assembly (see Front View).
E-Unit
bracket
assembly
bottom flange-
timer/bracket
Step 3
Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly.
The E-Unit bracket assembly shown above, will need to be removed (with a philips screwdriver) to allow the E-
Unit to swing back. This will allow the timer cord plug to pass between the E-Unit and rear panel.
Step 4
Remove 2 screws that secure timer to bracket.
Timer vents & bracket must be
attached as shown.
Step 5
Install bracket to replacement timer with 2 nuts. Adjust timer dial to current time. If necessary, adjust
timer charging times to match the original timer.
bracket
assembly
bottom flange-
timer/bracket
Step 6
Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from
the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned
with rear panel cutouts. Swing the E-Unit back into position and reinstall bracket assembly.
Plug in the E-Units power cords into the bottom outlets of the timer assembly.
notch
tab
Step 7
Reinstall the 3 interior shelves as follows:
1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in remaining 2 shelves into position as the bottom shelf.
DETAIL 'C'
Step 8
Reinstall 6 screws to rear panel that will secure the 3 interior shelves
(see DETAIL 'C'). DO NOT OVER TIGHTEN SCREWS.
Installation is now complete and ready for use.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
TIMER REPLACEMENT:
'E-UNIT AT FRONT LOCATION'
SEE DETAIL'B'
bottom shelf
SEE DETAIL 'A'
Step 1
Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefully unplug the power
cords of the E-Units from the timer assembly (see Front View) and unclip the power cords from the 4 clips located
at the bottom panel of the cart. Loosen the screw holding the E-Unit bracket assembly and remove all 4 bracket
assemblies (see DETAILS 'A' and 'B').
E-Unit power
cord
timer assembly
bottom shelf
Front View
bracket
assembly
clip
DETAIL 'B'
bracket
assembly
DETAIL 'A'
front-left
front-right
Step 2
Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf channel and set it aside.
Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf channel and set it aside.
DETAIL 'A'
Step 3
Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DETAIL 'A').
mounting
tab
DETAIL 'B'
Step 4
With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from
mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside.
bottom flange-
timer/bracket
Step 5
Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly.
Step 6
Remove 2 screws that secure timer to bracket.
Timer vents & bracket must be
attached as shown.
Step 7
Install bracket to replacement timer with 2 nuts. Adjust timer dial to current time. If necessary, adjust
timer charging times to match the original timer.
bottom flange-
timer/bracket
Step 8
Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from
the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned
with rear panel cutouts.
notch
tab
Step 9
Reinstall the 3 interior shelves as follows:
1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in remaining 2 shelves into position as the bottom shelf.
DETAIL 'C'
Step 10
Reinstall 6 screws to rear panel that will secure the 3 interior shelves
(see DETAIL 'C'). DO NOT OVER TIGHTEN SCREWS.
bottom shelf
front-left
front-right
Step 11
Carefully reinstall E-Units into position by placing bottom in first and tilting it in sideways to the top (underneath
the channel bracket of the cart top panel).
When repositioned correctly, the E-Units power switch should face the front.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-Unit is aligned with the slot in
the bracket assembly) and tighten screws securely.
Plug in the E-Unit power cords into the bottom outlets of the timer assembly (located underneath bottom shelf).
Press E-Unit power cords into the two wire clips located (in line, behind E-Units) on the bottom of cart.
Installation is now complete and ready for use.
LABEL INSTALLATION:
AUX. 1
AUX. 5
3
AUX. 2
AUX. 6
4
AUX. 3
1
AUX. 4
2
peel off and attach corresponding labels to
shelves and E-Units.
5
6
7
8
9
10
14
18
22
26
30
11
12
13
17
21
25
29
15
16
19
20
23
24
27
28
1
1
1
1
suggested installation of labels
shelf
1
1
1
1
2
2
2
2
E-Unit
E-Unit
E-Unit at front
E-Unit at rear
suggested label direction
PAD LOCK - DOOR:
Open Lock The First Time
1) Set the combination to 0-0-0-0
2) Depress shackle and pull open.
To Set You Own Combination
**REMEMBER: Combination can only be set when lock is open.
1) Insert “reset” tool (included in package) in hole on side of lock.
2) Push key in and turn key 90 degrees in either direction.
(Key automatically stays in this position).
Failure to exert force while pushing key in will result in a failed
attempt to set or reset combination.
3) Set wheels to desired combination.
4) Turn and remove reset tool. Lock is now set to new combination.
**BE SURE TO RECORD YOUR COMBINATION.
5) To lock scramble the wheels and close the shackle.
6) To reopen dial your combination and depress shackle.
Bretford
Bretford Ltd.
11000 Seymour Avenue
Franklin Park, IL 60131
TEL: 847.678.2545
800.521.9614
Technology House
2 Etongate, 110 Windsor Road
Slough, Berkshire SL1 2JA England
TEL: 01753 53 99 55
FAX: 847.678.0852
800.343.1779
FAX: 01753 53 94 78
Part #031-6566
Rev. 12.22.08 CZ
|
Nikon MOTO VE240 User Manual
Morphy Richards Cafe Rico Espresso coffee maker User Manual
Kenwood KDC U3049 User Manual
JVC kd g162 User Manual
Jura Capresso ENA 3 User Manual
Grindmaster 20 User Manual
GPX R308B User Manual
Compaq QUICKSPECS 294244 B21 User Manual
Casio PQ 32 User Manual
American Audio Radius 3000 User Manual