JVC MC R421U User Manual

INSTRUCTIONS  
MC-R421U  
For Customer Use:  
Enter below the Model No. and Serial  
No. which are located at the top of the  
unit. Retain this information for future  
reference.  
Model No. MC-R421U  
Serial No.  
This instruction book is made from 100% recycled paper.  
LST0033-001A  
The MC-R421U is a DVD-R drive designed for use with the JVC MC-8100U/8200U/8600U "CD/DVD Library".  
It is read compatible with CD-ROM, CD-R, CD-RW, DVD-ROM and DVD-R discs.  
The MC-R421U cannot be operated on its own.  
This drive is not compatible with the MC-1000U/E or MC-2000U series "CD-ROM Library" and MC-7000U series "DVD-  
RAM Library".  
For the compatible discs, see Specifications on page 8.  
When mounting this drive in the MC-8100U/8200U/8600U models, it is required to replace the ROM for the “CD/DVD  
Library” with the ROM provided with this drive.  
For information on firmware version upgrades and replacement of ROMs, please consult the retailer of the MC-R421U  
or JVC service agency.  
ACCESSORIES AND DOCUMENTATION  
Accessories  
Drive locking screw (M3 with washer) ............................................................................2 (including one spare)  
SCSI cable (with a connector cap, 1 m length) .......................................................1  
Clamp filter (with band) ...........................................................................................2  
ROM  
For MC-8100U  
: PLSS1721 (V1-03 or after) ........................................ 1  
For MC-8200U/8600U : PLSS1719 (V1-02 or after) ........................................ 2  
Documentation  
Instructions..............................................................................................................1  
INSTALLATION  
Please refer to the instruction manual of your Library for more information about the CD/DVD Library.  
1. How to Open the Door of the JVC Library  
In order to open the door, please refer to the section  
“HOW TO OPEN THE DOOR DURING OPERATION” in  
the instructions for the JVC Library.  
Drive locking screw  
mounting hole  
1. Select the [DOOR OPEN MODE] on the MENU screen of  
the LCD display section.  
Drive locking section  
2. Press and hold the SELECTkey for at least five seconds.  
Figure shows the MC-8100U  
3. Turn off the power of the JVC Library when the [THE DOOR  
CAN BE OPENED] message is displayed on the LCD dis-  
play section.  
Drive locking section  
4. Insert the key in the key cylinder located at the center of  
the door and turn it 90 degrees counterclockwise to unlock  
and open the door.  
Drive locking screw  
mounting hole  
Before you start installing the DVD-R Drive, be sure to  
turn off power of the host computer, all peripheral  
devices and the Library.  
Figure shows the MC-8200U  
3
INSTALLATION  
2. How to Open the Drive Storage Cover  
Also be sure to refer to the corresponding sections in the Library instructions.  
1. Remove the screws from the drive storage cover that is located at the rear of the Library.  
2. Remove the drive storage cover.  
Drive No.6  
Drive No.4  
Drive No.3  
Drive No.2  
Drive No.1  
Figure shows the MC-8200U  
Drive No.5  
Drive No.4  
Drive No.3  
Drive No.2  
Drive No.1  
Figure shows the MC-8100U  
Drive storage  
Drive storage  
section  
section  
Screws  
Screws  
Drive storage cover  
Screws  
Drive storage  
cover  
3. How to Determine the Installation Position of the DVD-R Drive  
1. Install the drives from the No.1 to No.6 slots (No. 1 to No. 4 in the case of the MC-8100U) in that order without skipping any  
drive slots.  
Begin installing drives from the lowest position (No.1).  
Drive storage section  
4. How to Install the DVD-R Drive  
Sensor slit  
•Beware of damage  
1. Insert the DVD-R drive from the rear of the JVC Library.  
Pay attention not to damage the sensor slit.  
Always insert the DVD-R Drive correctly.  
Check that cables connected on the rear of the unit are not caught  
or pinched when inserting the DVD-R Drive.  
2. Insert the DVD-R Drive slowly until the screw installation hole located  
on the side of the DVD-R Drive and the screw installation hole lo-  
cated on the drive locking section are aligned.  
3. Lock the DVD-R Drive in place by using the drive locking screw on  
the door panel side of the drive.  
Drive locking section  
Tighten the screw firmly.  
If the drive locking screw is loose, the drive and/or Library could  
suffer damage.  
Drive locking  
screw  
4
INSTALLATION  
5. How to Attach the SCSI Cable  
SCSI cable  
If required two SCSI bus channels may be used by adding the provided SCSI cable.  
If the DVD-R is recorded intermittently due to an insufficiency in the recording transfer  
rate on the SCSI bus, the recording quality may deteriorate and playback malfunc-  
tions may occur.  
Blind plate  
1. While holding the two blind plates, remove the four screws on the SCSI connector installa-  
tion section at the rear of the JVC CD/DVD Library in order to remove the two blind plates.  
SCSI-D  
SCSI-C  
2. Insert the provided SCSI cable through the installation hole from the back side of the  
rear panel and secure it with the four screws.  
SCSI-B  
SCSI-A  
Remove the connector cap of the SCSI cable for installation.  
Be sure that the SCSI connector is inserted in the correct direction.(It should be the  
same as the direction of the SCSI connector SCSI-A.)  
Connector cap  
3. If you are not connecting the SCSI cable to the OUT side of the SCSI connector  
SCSI-D, place the connector cap over it.  
6. How to Connect Cables to the DVD-R Drive  
Also refer to the corresponding sections in your Library Instructions Manual.  
1. Connect the power supply cable, control cable and SCSI cable to the connectors at the rear of the DVD-R Drive.  
When using the MC-8100U, the No. of the cable must always correspond to the No. of the drive bay to which it is being  
connected. If the cable with the wrong number is connedted, it will lead to the equipment malfunctioning.  
When using the MC-8200U/8600U, connect power supply and control cables, which lead from the side of the DVD-R  
drive bay to the drive.  
Insert all connectors firmly.  
Control cable  
Rear section of the DVD-R Drive  
1
14p  
N
W
Slide switch  
DIP switch  
4p  
2
Power cable  
3
Connection example of a SCSI cable  
SCSI cable  
Internal SCSI cable (additional)  
Up to two DVD-R drives can be connected  
(Terminate here  
(Terminate here  
)
)
DVD-R Drive  
DVD-R Drive  
SCSI connector  
SCSI-D(F)  
Connect an active terminator.  
OUT 2  
IN  
OUT 1  
IN  
SCSI-C(E)  
To be connected with host computer's SCSI host adapter No.2  
2
DVD-R Drive  
SCSI-B  
SCSI-A  
Connect an active terminator.  
1
To be connected with host computer's SCSI host adapter No.1  
Library SCSI board  
Internal SCSI cable (Standard)  
Up to 6 drives can be connected  
(Up to 4 drives in the case of MC-8100U)  
SCSI cables should be connected as a daisy chain connection. Each connector may be connected to the drive posi-  
tions as illustrated in the diagram.  
Terminate the physical end of the SCSI bus. For information on how to set the built-in terminator, refer to the item 1  
TERMof 7. How to Set the DIP and Slide Switches.  
For an external terminator we recommend that an active SCSI terminator is used with the JVC CD/DVD Library.  
5
INSTALLATION  
7. How to Set the DIP and Slide Switches  
Always turn OFF the power of Library when you set the dip switch modes.  
1. TERM This selects the use of the built-in terminator.  
Terminate the SCSI bus at the position where it physically terminates.  
When using the built-in terminator, set theTERM for the drive located at the physical end of the SCSI bus to ON,  
and the TERM for the other drives to OFF.  
When not using the built-in terminator, attach an external terminator to the OUT side of the SCSI connector.  
When using an external terminator, set TERM of all the drives to OFF.  
To improve the stability of SCSI bus communications, it is recommended to use an active external terminator.  
2. ID2  
3. ID1 This sets the SCSI ID No. on the drives.  
4. ID0  
Switch  
ID1  
SCSI ID  
No.  
Remarks  
ID2  
OFF  
OFF  
OFF  
OFF  
ON  
ID0  
OFF  
ON  
0
1
2
3
4
5
6
7
OFF  
OFF  
ON  
Default factory setting  
ON  
1
ON  
OFF  
ON  
ON  
W
N
OFF  
2
3
4
OFF  
OFF  
ON  
OFF  
ON  
ON  
(Factory setting)  
ON  
OFF  
ON  
W
N
ON  
ON  
Set the SCSI ID No. between 0 - 7 using only a ID No. that is not being used by other SCSI devices.  
Note that the default SCSI ID of the Library is 0 and the SCSI card is 7.  
For the details on default factory settings, please refer to the section SCSI ID No. SETTINGof the instructions  
for the JVC Library.  
Be sure to set the slide switch to N for use. (The position W is provided for use in servicing.)  
8. How to Reattach the Drive Storage Cover  
Always reattach the drive storage cover before switching ON the JVC Library.  
1. Fasten the panel with the screws that were removed in procedure (refer to 2. How to Open the Drive Storage Coveron  
page 4).  
9. How to Close and Lock the Door of the JVC Library  
Always close and lock the door before switching ON the JVC Library.  
1. Close the door and lock the key cylinder.  
10. Automatic Drive Detection Mode  
Please also refer to the corresponding sections in the CD/DVD Library instructions.  
If using the CD/DVD Library MC-8100U/8200U/8600U, be sure to execute the auto drive detection mode after in-  
stalling, adding, exchanging or removing drives, to prevent any malfunction.  
1. While holding the 8key on the control panel, turn on the power of the Library.  
2. When the LCD display shows DRIVE DETECTION COMPLETED, turn off the power of the Library.  
3. Turn the Library on again.  
The DRIVE DISPLAY of the CD/DVD Library displays this drive as a DVD-RAM.  
Before you install, add, remove or replace drives, and/or change the SCSI ID No., turn OFF the power of the host  
computer. Remember to turn it ON again after completing the necessary operations.  
6
INSTALLATION  
11. Example of a SCSI Cable Connection  
When interconnecting the JVC CD/DVD Library and the host computer with a SCSI cable, use a high-impedance,  
shield cable with two clamp filters fitted near both connectors.  
SCSI cable (of high impedance, shielded design)  
External SCSI cable to host computer's  
SCSI host adapter No.2 for controlling  
To “SCSI-C”  
the Library  
connector  
Attach the active  
terminator to the  
OUT connector.  
To “SCSI-A”  
connector  
External SCSI cable to host computer's  
SCSI host adapter No. 1 for controlling  
Host computer  
the Library  
CD/DVD Library  
An operational error may occur when the total length of the internal and external SCSI cables exceed 3 meters  
(with SCSI-2, 10 Mbytes/sec. sync).When the SCSI bus is used as SCSI-2, 5 Mbytes/sec. async, the total length of  
the cables can be extended to up to 6 meters.  
Regarding the length of the provided SCSI cable is approx. 1 m (3.3 feet).  
The length of the SCSI cable inside the JVC CD/DVD Library refer to CONNECTING SCSI CABLES AND POWER  
CORDin the operation manual for the main unit.  
Be sure to lock the connectors of the external SCSI cable once they are connected.  
INSTALLATION PROCEDURE  
2
Press the clamp filter against the connector  
and fasten it with a provided band.  
Tighten until the dabs  
are completely locked.  
Pull the band tightly.  
Cut off any  
extra length.  
Fit the clamp filter around the cable.  
1
Signal disturbance may occur if a high-impedance, shielded SCSI cable is not used. Also, the above clamp  
filters are necessary for the JVC CD/DVD Library in order to comply with EMI Standard EN55022 Class A.  
PRECAUTIONS BEFORE USE  
Read the following before installing this drive in your Library for the first time.  
To mount this drive on the MC-8100U/8200U/8600U in your Library, the firmware of the CD/DVD Library should be  
upgraded. Please change the ROM in the CD/DVD Library to the ROM provided with this drive.  
For the ROM replacement method, consult your dealer or nearest JVC-authorized service agent.  
Do not set the Power switch of the CD/DVD Library to ON until all of the work described above has been  
completed.  
7
SPECIFICATIONS  
Interface  
: SCSI-2  
Data transmission rate  
: Sustained (When the host adapter is set to the maximum sync transfer rate of 20 Mbytes/sec.)  
DVD-R for General (Single-sided 4.7 GB or double-sided 9.4 GB, recordable):  
3.31 Mbytes/s to 5.75 Mbytes/s  
DVD-ROM (Single Layer), DVD-R for General (Single-sided 4.7 GB or double-sided 9.4 GB, playback)  
3.44 Mbytes/s to 5.78 Mbytes/s (6X max., CAV)  
DVD-RAM (Ver. 2.1, single-sided 4.7 GB, double-sided 9.4 GB, playback only):  
2.77 Mbytes/s  
DVD-RAM (Ver. 1.0, single-sided 2.6 GB, playback only):  
1.38 Mbytes/s  
CD-ROM/-R (Playback only):  
1.5 Mbytes/s to 3.6 Mbytes/s (24X max., CAV)  
CD-RW (Playback only):  
Max. 1.8 Mbytes/s (12X max., CAV)  
Burst  
Max. 8 Mbytes/sec. (async transfer)  
Max. 10 Mbytes/sec. (sync transfer)  
Average access time  
(1/3 stroke, typ.)  
: DVD-R for General 4.7 GB  
DVD-ROM (Single Layer)  
DVD-RAM (4.7 GB)  
DVD-RAM (2.6 GB)  
CD-ROM  
: 100 ms  
: 100 ms  
: 135 ms  
: 155 ms  
: 95 ms  
The above values were measured using JVC's measurement method.  
Buffer capacity  
: 1 Mbyte  
Additional write count  
(DVD-R for General 4.7 GB)  
: Max. 100 times (per disc side)  
(Assuming that each disk drive insertion/ejection cycle is counted as one time)  
Accessories  
: SCSI cable (with a connector cap, 1 m length) ..................... x 1  
Clamp filter (with band) ......................................................... x 2  
ROM ...................................................................................... x 3  
Drive locking screw ............................................................... x 2  
Operating environment  
: Temperature : 5˚C to 35˚C  
Humidity  
: 10% to 80% (without condensation)  
Dimensions  
Weight  
: 171 mm x 47.5 mm x 240 mm (WxHxD)  
: 1.5 kg  
Applicable discs  
: DVD-R for General 4.7 GB  
Recommended discs (Single-sided 4.7 GB):  
Panasonic LM-RF47  
Panasonic LM-RS47B50 (Spindle type, 50-disc pack)  
Verbatim 094077  
Verbatim 094058 (Spindle type, 50-disc pack)  
Maxell DR47.1P  
Maxell DR47.50S (Spindle type, 50-disc pack)  
Recommended disc (Double-sided 9.4 GB):  
Verbatim 094171 (Spindle type, 50-disc pack)  
Maxell DR94.50S (Spindle type, 50-disc pack)  
DVD-R 3.95 GB (Ver. 1.0, disc at once, playback only)  
DVD-ROM  
DVD-RAM (Ver. 2.1, single-sided 4.7 GB, double-sided 9.4 GB, playback only)  
DVD-RAM (Ver. 1.0, single-sided 2.6 GB, playback only)  
CD-ROM (Mode 1, Mode 2, etc.)  
CD-R (Playback only)  
CD-RW (Playback only)  
* Note 1 : With the DVD-R, DVD-RAM, CD-R and CD-RW, the full performance may not be evident  
depending on the write condition.  
* Note 2 : Only the discs with a diameter of 120 mm are applicable.  
The specifications and appearance of this unit are subject to change without notice.  
8
VICTOR COMPANY OF JAPAN, LIMITED  
© 2001 VICTOR COMPANY OF JAPAN, LIMITED  
is a registered Trademark owned by VICTOR COMPANY OF JAPAN, LTD.  
Printed in Japan  
LST0033-001A  
is a registered Trademark in JAPAN, the U.S.A., the U.K. and many other countries.  

NETGEAR SC101 User Manual
Mr Coffee CUBIKA User Manual
Motorola V190 User Manual
Maxtor DIAMONDMAX 91536H2 User Manual
Hotpoint HCM60 User Manual
Eton Cell Phone Accessories User Manual
Bunn TITAN DUAL 401190000G User Manual
Barracuda Networks ST310220A User Manual
APC SMT 2200 VA User Manual
321 Studios Oil Furnace FLF110D48E User Manual