JVC KS FX480J User Manual

CASSETTE RECEIVER

KS-FX480

RECEPTOR-REPRODUCTOR DE CASSETTE KS-FX480

RADIOCASSETTE

KS-FX480

ATT

SOUND

200W

KS-FX480

Multi

Music

Scan

SOURCE

TAPE

VOL

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

For customer Use:

Enter below the Model No. and

Serial No. which are located on

the top or bottom of the cabinet.

Retain this information for future

reference.

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Model No.

Serial No.

GET0068-001A

[J]

LOCATION OF THE BUTTONS

Control panel

Display window

g h

3 4

200W

KS-FX480

Multi

TAPE

Music

Scan

9 p

y u i

;

1 4

/¢

buttons

o DISP (display) button

2 5 (up) button

Tape ` button

•

Also functions as SSM buttons when pressed

together with MODE button.

3 ∞ (down) button

4 Remote sensor

5 Display window

6 0 (eject) button

7 FM AM button

; EQ (equalizer) button

Display window

(Dolby B) indicator

s Main display

8 TAPE CD-CH button

d Volume (or audio) level indicator

Equalization pattern indicator

f Tuner reception indicators

MO (monaural), ST (stereo)

g C-EQ (custom equalizer) indicator

h RND (random) indicator

j RPT (repeat) indicator

k LOUD (loudness) indicator

l Sound mode indicators

ROCK, CLASSIC, POPS, HIP HOP, JAZZ,

USER.

(standby/on/attenuator) button

(control panel release) button

q SEL (select) button

w Control dial

e MO (monaural) button

(Dolby B) button

t RPT (repeat) button

y RND (random) button

u Number buttons

i MODE button

•

Also functions as SSM buttons when pressed

together with DISP (display) button.

/ Source/clock display

z Tape–in indicator

2. Place the battery.

Preparing the remote controller

Slide the battery into the holder with the + side

facing upwards so that the battery is fixed in

Before using the remote controller:

the holder.

Lithium coin battery

(product number:

CR2025)

3. Return the battery holder.

Insert again the battery holder pushing it until

you hear a clicking sound.

3 • Selects the preset stations while listening to

the radio.

Remote controller

Each time you press the button, the preset

station number increases, and the selected

station is tuned in.

RM–RK50

• Skips to the previous disc while listening to

the CD changer.

Each time you press the button, the disc

number decreases, and the selected disc

starts playing.

ATT

SOUND

4 Functions the same as the control dial on the

main unit.

SOURCE

NOTE: This button does not function for the

preferred setting mode adjustment.

5 Selects the sound mode.

Each time you press the button, the (C-EQ:

Custom Equalizer) mode changes.

VOL

6 Selects the source.

Each time you press the button, the source

changes.

7 • Searches stations while listening to the radio.

• Functions as the fast forward or rewind buttons

or multi music scan buttons while listening to

a cassette. To release this operation, press

button 2 then starts playback.

1 • Turns on the unit if pressed when the unit is

turned off.

• Fast-forwards or reverses the track if pressed

and held while listening to the CD changer.

• Skips to the beginning of the next track or goes

back to the beginning of the current (or

previous) tracks if pressed briefly while

listening the CD changer.

• Turns off the unit if pressed and held until“SEE

YOU” appears on the display.

• Drops the volume level in a moment if pressed

briefly.

Press again to resume the volume.

2 • Selects the band while listening to the radio.

Each time you press the button, the band

changes.

• Changes the tape direction while listening to

a cassette.

Each time you press the button, the tape

direction changes alternately.

• Skips to the next disc while listening to the

CD changer.

Each time you press the button, the disc

number increases, and the selected disc

starts playing.

BASIC OPERATIONS

200W

KS-FX480

Multi

Music

Scan

TAPE

Turning on the power

3 Adjust the volume.

To increase the volume.

1 Turn on the power.

“HELLO” appears on the

display.

To decrease the volume.

Volume or audio

level (see page 18)

indicator

Note on One-Touch Operation:

When you select a source in step 2 below, the

power automatically comes on. You do not have

to press this button to turn on the power.

Volume level appears.

2 Select the source.

FM1

FM2

TAPE

FM3

4 Adjust the sound as you want.

TAPE

(See pages 13 – 15.)

(or LINE IN^**)

To drop the volume in a moment

To operate the tuner (FM or AM),

see pages 7 – 9.

Press

briefly while listening to any

source. “ATT” starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

To operate the tape,

see pages 10 – 12.

To operate the CD changer,

see pages 20 – 21.

To operate the external component,

see page 22.

To turn off the power

Notes:

Press and hold

on the display.

until “SEEYOU” appears

Without connecting the CD changer you cannot

select the CD changer as the source.

** To select the external component other than the

CD Changer, the “EXT IN” setting must be set to

LINE IN. (See page 18.)

Note:

When you use this unit for the first time, set the built-in

clock correctly, see page 16.

RADIO BASIC OPERATIONS

200W

KS-FX480

Multi

Music

TAPE

Scan

To stop searching before a station is received,

press the same button you have pressed for

searching.

Listening to the radio

You can use either automatic searching or manual

searching to tune in to a particular station.

Searching a station manually:

Manual search

Searching a station automatically:

Auto search

1 Select the band (FM1 – 3, AM).

FM1

(F1)

FM2

(F2)

FM3

(F3)

FM1

(F1)

FM2

(F2)

FM3

(F3)

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

Selected band appears.

2 Press and hold ¢

or 4

until

Note:

“MANU (manual)” starts flashing on

the display.

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

2 Start searching a station.

Press ¢

to search

stations of higher

frequencies.

Selected band appears.

Press 4

to search

stations of lower

frequencies.

While searching stations, “SEEK” appears

on the display.

When a station is received, searching stops.

CONTINUED ON THE NEXT PAGE

3 Tune in to a station you want while

Storing stations in memory

“MANU (manual)” is flashing.

Press ¢

to tune

in to stations of higher

frequencies.

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

Press 4

to tune

in to stations of lower

frequencies.

FM station automatic preset: SSM

• If you release your finger from the button,

the manual mode will automatically turn off

after 5 seconds.

You can preset 6 local FM stations in each FM band

(FM1, FM2 and FM3).

• If you hold down the button, the frequency

keeps changing. (in 200 kHz intervals for

FM and 10 kHz for AM) until you release

the button.

1 Select the FM band (FM1 – 3) you want

to store FM stations into.

Each time you press the

button, the band changes as

follows:

When an FM stereo broadcast is hard to

FM1

(F1)

FM2

(F2)

FM3

(F3)

receive:

1 Press MODE to enter the functions

mode while listening to an FM

stereo broadcast.

2 Press and hold both buttons for more

“MODE” appears on the lower part

of the display, and the number

buttons work as different function

buttons.

than 2 seconds.

2 Press MO (monaural), while

“MODE” is still on the display, so

that the MO indicator lights up on

the display.

Then, each time you press MO

(monaural), the MO indicator lights

up and goes off alternately.

Lights up when receiving an FM broadcast in stereo.

“SSM” appears, then disappears when automatic

preset is over.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2 or FM3).

These stations are preset in the number buttons —

No.1 (lowest frequency) to No.6 (highest frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

reception will be improved (the ST indicator

goes off).

Manual preset

You can preset up to 6 stations in each band (FM1,

FM2, FM3 and AM) manually.

4 Repeat the above procedure to store

other stations into other preset

numbers.

Ex.: Storing an FM station of 88.3 MHz into the

preset number 1 of the FM1 band

Notes:

• A previously preset station is erased when a new station

is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example, during

battery replacement). If this occurs, preset the stations

again.

1 Select the band (FM1 – 3, AM) you

want to store stations into (in this

example, FM1).

Each time you press the

button, the band changes

as follows:

Tuning in to a preset station

FM1

(F1)

FM2

(F2)

FM3

(F3)

You can easily tune in to a preset station.

Remember that you must store stations first. If you

have not stored them yet, see “Storing stations in

memory” on pages 8 and 9.

2 Tune in to a station (in this

example, of 88.3 MHz).

Press ¢

to tune

1 Select the band (FM1 – 3, AM).

in to stations of higher

frequencies.

Press 4

to tune

in to stations of lower

frequencies.

FM1

(F1)

FM2

(F2)

FM3

(F3)

2 Select the number (1 – 6) for the preset

station you want.

3 Press and hold the number button (in

this example, 1) for more than 2

seconds.

Note:

You can also use the 5 (up) or ∞ (down) buttons on

the unit to select the next or previous preset stations.

Each time you press the 5 (up) or ∞ (down) buttons,

the next or previous preset station is tuned in.

Selected band/preset number and

“MEMO” (memory) appear

alternately for a while.

TAPE OPERATIONS

200W

KS-FX480

Multi

Music

Scan

TAPE

To stop play and eject the cassette

Press 0.

Tape play stops, the control panel opens and then

the cassette automatically ejects from the cassette

compartment.The source changes to the previously

selected one.

Listening to a cassette

You can play back type 1 (normal) tapes.

1 Open the control panel.

If you change the source, tape play also stops

(without ejecting the cassette this time).

• You can eject the cassette while the unit is turned

off by pressing 0.

2 Insert a cassette into the cassette

compartment.

To fast-forward and rewind a tape

The unit turns on and

tape play starts

automatically.

Press ¢

for more than

1 second to fast-forward the

tape.

When the tape reaches its

end, the tape is reversed and

playback starts from the

beginning of the other side.

3 Close the control panel by hand.

Tape–in indicator appears.

Press 4

for more than

1 second to rewind the tape.

When the tape reaches its

end, playback of the same

side starts.

To stop fast forward and rewind at any

position on the tape, press `.

Tape play starts from that position on the tape.

4 Select the tape direction.

Each time you press `,

the tape direction changes

alternately forward

Notes:

(TAPE

) and reverse

• When one side of the tape reaches its end during

play, the other side of the tape automatically starts

playing. (Auto Reverse)

Note on One-Touch Operation:

• When the tape reaches its end while fast-forwarding,

the tape direction will be changed automatically.

When a cassette is already in the cassette

compartment, select tape as the source by

pressing TAPE CD-CH to start tape play.

Finding the beginning of a tune

To play back tapes recorded with the

Dolby B NR*

1 Press MODE to enter the functions mode

while listening to a tape.

“MODE” appears on the lower part of the

display, and the number buttons work as

different function buttons.

Multi Music Scan allows you to automatically start

playback from the beginning of a specified tune.

You can specify up to 9 tunes ahead of or before

the current tune.

During playback

Specify where (how many tunes ahead of

or before the current tune) the tune you

want is located.

2 Press

the display so that the

lights up.

(Dolby B), while “MODE” is still on

(Dolby B) indicator

“DOLBY B” also appears on the display for

several seconds.

Press ¢

to locate a

tune ahead of the current

tune on the cassette.

To cancel the Dolby B NR, repeat steps 1

and 2 above again.

Press 4

to locate a

tune before the current tune

on the cassette.

*Manufactured under license from Dolby

Laboratories.

“Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

Prohibiting cassette ejection

Each time you press the buttons, the number

changes up to ±9.

You can prohibit cassette ejection and “lock” a

cassette in the cassette compartment.

When the beginning of the specified tune is

located, playback starts automatically.

Press and hold TAPE CD-CH and

more than 2 seconds.

for

“NO EJECT” flashes on the display for about 5

seconds, and the cassette is “locked.”

Notes:

• While locating a specified tune:

– If the tape is rewound to its beginning, playback

starts from the beginning of that side.

– If the tape is fast-forwarded to the end, it is

reversed and played from the beginning of the

other side.

To cancel the prohibition and “unlock” the

cassette, press and hold TAPE CD-CH

and

for more than 2 seconds again.

“EJECT OK” flashes for about 5 seconds, and this

time the cassette is “unlocked.”

• In the following cases, the Multi Music Scan

function may not operate correctly:

– Tapes with tunes having long pianissimo passages

(very quiet parts) or non-recorded portions

between tunes.

– Tapes with short non-recorded sections.

– Tapes with high level of noise or humming

between tunes.

– The Dolby NR setting does not match. For

example, if Dolby B NR is on and the tape was

recorded with no Dolby NR.

Playing the current tune repeatedly

You can play the current tune repeatedly (Repeat

Play).

Other convenient tape functions

Skipping the blank portions on the tape

You can skip blank portions between the tunes

(Blank Skip).

1 Press MODE to enter the functions

mode while playing a tune you want

to hear over again on a cassette.

“MODE” appears on the lower part

of the display, and the number

buttons work as different function

buttons.

When this function is on, the unit skips blank

portions of 15 seconds or more, fast-forwards to

the next tune, then starts playing it.

• See also “Changing the general settings (PSM)”

on pages 16 and 17.

2 Press RPT (repeat), while “MODE”

is still on the display, so that the

RPT indicator lights up on the

display.

1 Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see page 17.)

Lights up when Repeat Play is turned on.

2 Press ¢

or 4

to select

“B. SKIP (blank skip).”

When the tune has been played, the tape is

automatically rewound to the beginning of that

tune and the same tune will be played again.

To cancel Repeat Play, repeat steps 1 and 2

above again so that the RPT indicator goes off.

3 Turn the control dial clockwise to

select “ON.”

Note:

In the following cases, Blank Skip and Repeat Play

may not operate correctly:

– Tapes with tunes having long pianissimo passages

(very quiet parts) or non-recorded portions during

tunes.

Now Blank Skip is

activated.

– Tapes with short non-recorded sections.

– Tapes with high level noise or humming between

tunes.

– The Dolby NR setting does not match. For example,

if Dolby B NR is on and the tape was recorded with

no Dolby NR.

4 Finish the setting.

To cancel Blank Skip, repeat the same

procedure and select “OFF” in step 3 by turning

the control dial counterclockwise.

SOUND ADJUSTMENTS

Adjusting the sound

2 Adjust the level.

To increase the level.

You can adjust the sound characteristics to your

preference.

To decrease the level.

1 Select the item you want to adjust.

Each time you press the

button, the adjustable items

change as follows:

Equalization pattern changes as

you adjust the bass or treble.

BAS

TRE

FAD

(bass)

(treble)

(fader)

BAL

VOL

LOUD

(balance)

(volume)

(loudness)

Note:

Indication To do:

Range

Normally the control dial works for volume

adjustment. So you do not have to select “VOL” to

adjust the volume level.

BAS

TRE

FAD*

BAL

Adjust the bass.

–06 (min.)

+06 (max.)

Adjust the treble. –06 (min.)

+06 (max.)

Adjust the front

and rear speaker

balance.

R06 (Rear only)

F06 (Front only)

Adjust the left

and right speaker

balance.

L06 (Left only)

R06 (Right only)

LOUD

Boost low and high

frequencies to

produce a well-

balanced sound

at low volume

level.

LOUD ON

LOUD OFF

VOL

Adjust the volume. 00 (min.)

50 (max.)

If you are using a two-speaker system, set the

fader level to “00.”

Indication

For:

Preset values

Selecting preset sound modes

(C-EQ: Custom Equalizer)

BAS

TRE

LOUD

USER

ROCK

(Flat sound)

OFF

Rock or

+03

+01

disco music

You can select a preset sound mode (C-EQ:

Custom Equalizer) suitable to the music genre.

CLASSIC Classical

music

+01

+04

–02

OFF

1 Press EQ.

POPS

Light music

+01

OFF

The last selected sound mode is

recalled and applied to the

current sound.

HIP HOP Funk or Rap +02

music

JAZZ

Jazz music

+02

+03

OFF

Note:

• You can adjust each sound mode to your preference,

and store it in memory.

If you want to adjust and store your original sound

mode, see “Storing your own sound adjustments”

on page 15.

Sound mode indicator flashes

Ex.: If you have selected “USER” previously

To store a sound mode separately for

each playback source (C-EQ Link)

You can select a sound mode and store it in

memory. It will be recalled every time you select

the same source and will be shown on the display.

A sound mode can be stored for each of the

following sources — FM1, FM2, FM3, AM, tape

and external components.

2 Select the sound mode you want.

Each time you press the button,

the sound modes change as

follows:

USER

JAZZ

ROCK

CLASSIC

POPS

HIP HOP

1 Press and hold SEL (select) for more than 2

seconds so that one of the PSM items

appears on the display.

2 Press ¢

or 4

to select “C-EQ

LINK (custom equalizer link).”

3 Turn the control dial clockwise to select “LINK

ON.”

4 Press SEL (select) to finish the setting.

Sound mode indicator flashes.

Ex.: When you select “ROCK”

To cancel C-EQ Link, repeat the same

procedure and select “LINK OFF” in step 3.

Note:

When you change the “C-EQ LINK” setting, the

sound mode (C-EQ) is automatically reset to “USER”.

• When “C-EQ LINK” is set to “LINK ON,”

The selected sound mode can be stored in

memory for the current source.

Each time you change to the same source, the

same sound mode is also recalled and shown

on the display. The C-EQ indicator also flashes.

• When “C-EQ LINK” is set to “LINK OFF”

The selected sound mode effect applies to any

source.

4 Adjust the level.

To increase the level.

To decrease the level.

Equalization pattern

changes as you adjust

the bass or treble.

Storing your own sound

adjustments

You can adjust the sound modes to your preference

and store your own adjustments in memory.

Ex.: When you adjust “TRE”

• There is a time limit in doing the following

procedure. If the setting is canceled before you

finish, start from step 1 again.

5 Repeat steps 3 and 4 to adjust the

other items.

1 Call up the sound mode you want to

adjust.

6 Repeat the same procedure to store

other sound modes.

The last selected sound mode is

recalled and applied to the

current sound.

To reset to the factory settings, repeat the

same procedure and reassign the preset values

listed in the table on page 14.

Sound mode indicator flashes

Ex.: If you have selected “ROCK” previously

2 Select the sound mode you want.

3 Select the item you want to adjust.

• See page 13 for details.

OTHER MAIN FUNCTIONS

To check other information during play, press

DISP (display).

Setting the clock

Each time you press the button, the other

information (either the clock or the source name)

will be shown on the lower part of the display for

a while.

1 Press and hold SEL (select) for more

than 2 seconds so that one of the PSM

items appears on the display.

(See page 17.)

• During tuner operation:

Band

Clock

• During tape operation:

Play mode (tape direction)

Clock

• During CD changer operation:

2 Set the hour.

1 Select “CLOCK H (hour)” if not shown on

the display.

Disc number

Clock

2 Adjust the hour.

• During external component operation:

Clock appears and disappears alternately.

To check the current clock time while the unit

is turned off, press DISP (display).

The power turns on, the clock time is shown for 5

seconds, then the power turns off.

3 Set the minute.

Changing the general settings

(PSM)

1 Select “CLOCK M (minute).”

2 Adjust the minute.

You can change the items listed on the next page

by using the PSM (Preferred Setting Mode) control.

Basic Procedure

1 Press and hold SEL (select) for more

than 2 seconds so that one of the PSM

items appears on the display.

(See page 17.)

4 Finish the setting.

2 Select the PSM item you want to

adjust. (See page 17.)

4 Repeat steps 2 and 3 to adjust the

3 Adjust the PSM item selected.

other PSM items if necessary.

5 Finish the setting.

Preferred Setting Mode (PSM) items

Factory-preset See

Set.

settings

page

Counter-

clockwise

Clockwise

Hold.

Select.

CLOCK H

CLOCK M

C-EQ LINK

Hour adjustment

Back

Advance

1:00

15, 18

Minute adjustment

Custom equalizer

linkage

LINK OFF

AUDIO 1

LINK ON

AUDIO 2

LINK OFF

AUDIO 2

AUTO

LEVEL

Level display

OFF

DIMMER

Dimmer mode

AUTO

OFF

B. SKIP

Blank skip

OFF

EXT IN*

External component

CHANGER

LINE IN

CHANGER

•

Press SEL (select) to finish the setting.

Displayed only when one of the following sources is selected – FM, AM and tape.

To set Custom Equalizer Link – C-EQ LINK

To select the external component to use

– EXT IN

You can connect the external component to the CD

changer jack on the rear using the Line Input Adaptor

KS-U57 (not supplied).

To use the external component as the playback

source through this unit, you need to select which

component – CD changer or external component

– to use.

When shipped from the factory, CD changer is

selected as the external component.

A different sound mode (C-EQ) can be stored in

memory for each source so that you can change

the sound modes simply by changing the sources.

When shipped from the factory, this mode is

deactivated.

• LINK ON: Different sound modes for different

sources.

• LINK OFF: One sound mode for all sources.

To select the level meter – LEVEL

You can select the level display according to your

• LINE IN:

To use the external component other

than CD changer.

• CHANGER: To use the CD changer.

preference.

When shipped from the factory, “AUDIO 2” is

selected.

Note:

For connecting the Line Input Adaptor KS-U57 and the

external component, refer to the Installation/Connection

Manual (separate volume).

• AUDIO 1: Shows the audio level indicator.

• AUDIO 2: Alternates between “AUDIO 1”

setting and illumination display.

• OFF:

Erases the audio level indicator.

To select the dimmer mode – DIMMER

When you turn on the car head lights, the display

automatically dims (Auto Dimmer).

When shipped from the factory, Auto Dimmer

mode is activated.

• AUTO:

• OFF:

• ON:

Activates Auto Dimmer.

Cancels Auto Dimmer.

Always dims the display.

Note:

Auto Dimmer equipped with this unit may not work

correctly on some vehicles, particularly on those

having a control dial for dimming.

In this case, set the dimmer mode to “ON” or “OFF.”

Attaching the control panel

Detaching the control panel

1 Insert the right side of the control panel

You can detach the control panel when leaving

the car.

into the groove on the panel holder.

When detaching or attaching the control panel,

be careful not to damage the connectors on the

back of the control panel and on the panel holder.

Detaching the control panel

Before detaching the control panel, be sure to turn

off the power.

2 Press the left side of the control panel

to fix it to the panel holder.

1 Unlock the control panel.

2 Pull the control panel out of the unit.

Note on cleaning the connectors:

If you frequently detach the control panel, the

connectors will deteriorate.

To minimize this possibility, periodically wipe the

connectors with a cotton swab or cloth moistened

with alcohol, being careful not to damage the

connectors.

3 Put the detached control panel into the

provided case.

Connectors

CD CHANGER OPERATIONS

200W

KS-FX480

Multi

Music

Scan

TAPE

We recommend that you use one of the CH-X series

with your unit.

Elapsed playing time

Track number

If you have another CD automatic changer, consult

your JVC car audio dealer for connections.

• For example, if your CD automatic changer is one of

the KD-MK series, you need a cord (KS-U15K) for

connecting it to this unit.

Disc number**

** The clock time is shown if you press DISP

(display) to see the clock time. (See page 16.)

Before operating your CD automatic changer:

• Refer also to the Instructions supplied with your

CD changer.

• If no discs are in the magazine of the CD

changer or the discs are inserted upside down,

“NO DISC” will appear on the display. If this

happens, remove the magazine and set the

discs correctly.

Note on One-Touch Operation:

When you press TAPE CD-CH, the power automatically

turns on. You do not have to press

the power.

to turn on

• If “RESET 1” – “RESET 8” appears on the

display, something is wrong with the

connection between this unit and the CD

changer.If this happens, check the connection

and make sure the cords are connected firmly.

Then, press the reset button of the CD

changer.

To fast-forward or reverse the track

Press and hold ¢

while playing a CD,

to fast-forward the track.

Press and hold 4

while playing a CD,

to reverse the track.

Playing CDs

To go to the next tracks or the previous tracks

Press ¢

briefly,

Select the CD automatic changer (CD).

while playing a CD, to go

ahead to the beginning of

the next track. Each time

you press the button

consecutively, the

TAPE

CD^*

TAPE

(or LINE IN)

beginning of the next

tracks is located and

played back.

* If you have not connected a CD changer, or if

you have changed the “EXT IN” setting to

“LINE IN” (see page 18), you cannot select the

CD changer.

Press 4

briefly, while

playing a CD, to go back to

the beginning of the current

track. Each time you press

the button consecutively,

the beginning of the

Playback starts from the first track of the first

disc.

All tracks of all discs are played back.

previous tracks is located

and played back.

To go to the next discs or the previous discs

Selecting CD playback modes

To play back tracks at random (Random Play)

Press 5, while playing a

disc, to go to the next disc.

Each time you press the

button consecutively, the

first track of the next disc is

located and played back.

1 Press MODE to enter the functions

mode while playing a disc.

“MODE” appears on the lower part of

the display, and the number buttons

work as different function buttons.

2 Press RND (random), while “MODE”

is still on the display, so that the

RND indicator lights up on the

display.

Press ∞, while playing a

disc, to go to the previous

disc. Each time you press

the button consecutively,

the first track of the

Then, each time you press RND

(random), the random play mode

changes as follows:

previous disc is located and

played back.

RND1

(Random1)

RND2

(Random2)

To go to a particular disc directly

Press the number button corresponding to the disc Mode

Canceled

Plays at random

RND

Indicator

number to start its playback (while the CD changer

is playing).

RND1

(Random1)random1)

Lights

All tracks of the current

disc, then the tracks of

the next disc and so on.

RND2

Flashes All tracks of all discs

(Random2)(random2)

inserted in the

magazine.

• To select a disc number from 1 – 6:

Press 1 (7) – 6 (12) briefly.

• To select a disc number from 7 – 12:

Press and hold 1 (7) – 6 (12) for more than 1

second.

To play back tracks repeatedly (Repeat Play)

1 Press MODE to enter the functions

mode while playing a disc.

“MODE” appears on the lower part

of the display, and the number

buttons work as different function

buttons.

Elapsed playing time

Track number

2 Press RPT (repeat), while “MODE” is

still on the display, so that the RPT

indicator lights up on the display.

Then, each time you press RPT

(repeat), the repeat play mode

changes as follows:

Disc number**

** The clock time is shown if you press DISP

(display) to see the clock time. (See page 16.)

RPT1

RPT2

(Repeat2)

(Repeat1)

Canceled

RPT

Indicator

Mode

Plays repeatedly

RPT1

Lights

The current track

(Repeat1)

(or specified track).

RPT2

(Repeat2)

Flashes All tracks of the current

disc (or specified disc).

EXTERNAL COMPONENT OPERATIONS

200W

KS-FX480

Multi

Music

TAPE

Scan

Playing an external component

2 Turn on the connected component

and start playing the source.

You can connect the external component to the CD

changer jack on the rear using the Line Input Adaptor

KS-U57 (not supplied).

3 Adjust the volume.

Preparations:

• For connecting the Line Input Adaptor KS-U57 and

the external component, refer to the Installation/

Connection Manual (separate volume).

• Before operating the external component using the

following procedure, select the external input

correctly. (See “To select the external component to

use – EXT IN” on page 18.)

4 Adjust the sound characteristics

you want. (See pages 13 – 15.)

1 Select the external component

(LINE IN).

TAPE

LINE IN

(or CD)

TAPE

• If “LINE IN” does not appear on the display, see

page 18 and select the external input (“LINE IN”).

• Displayed only when one of the following

sources is selected – FM, AM and tape.

Note on One-Touch Operation:

When you press TAPE CD-CH, the power

automatically comes on. You do not have to press

to turn on the power.

MAINTENANCE

This unit requires very little attention, but you will

be able to extend the life of the unit if you follow

the instructions below.

CAUTION:

• Do not play the cassettes with peeling labels;

otherwise, they can damage the unit.

• Tighten tapes to remove slack since loose tape

may become entangled with the mechanism.

• Do not leave a cassette in the cassette

compartment after use, as the tape may become

slack.

To clean the head

The function below is also provided to ensure the

longer life of this unit.

Ignition key-off release/Ignition key-on

play

• Turning off the ignition key with a cassette in the

compartment automatically releases the tape

from the unit’s tapehead.

• Turning on the ignition key with a cassette in the

compartment starts playback automatically if you

turned off the ignition during tape play.

• Clean the heads after every 10 hours of use using

a wet-type head cleaning tape (available at an

audio store).

When the head becomes dirty, you may realize

the following symptoms:

– Sound quality is reduced.

– Sound level decreases.

– Sound drops out.

• Do not play dirty or dusty tapes.

• Do not touch the highly-polished head with any

metallic or magnetic tools.

To keep the tape clean

• Always store the cassettes in their storage cases

after use.

• Do not store cassettes in the following places:

– Subject to direct sunlight

– With high humidity

– At extremely hot temperatures

TROUBLESHOOTING

What appears to be trouble is not always serious. Check the following points before calling a service

center.

Remedies

Causes

Symptoms

Insert the cassette with the

exposed tape facing to the right.

You have tried to insert a

cassette in the wrong way.

• A cassette tape cannot be

inserted.

Press and hold TAPE CD-CH

Cassette ejection is prohibited.

• A cassette tape cannot be

ejected.

and

for more than two

seconds.

This is not a malfunction.

The tape head is dirty.

• Cassette tapes become hot.

Clean it with a head cleaning

tape.

• Tape sound is at very low

level and sound quality is

degraded.

Check the cords and

connections.

Connections are not good.

• Sound is sometimes

interrupted.

Adjust it to the optimum level.

The volume is turned to the

minimum level.

• Sound cannot be heard from

the speakers.

Check the cords and

connections.

Connections are incorrect.

Signals are too weak.

Store stations manually.

• SSM (Strong-station

Sequential Memory)

automatic preset does not

work.

Connect the antenna firmly.

The antenna is not connected

firmly.

• Static noise while listening to

the radio.

Insert CDs into the magazine.

Insert them correctly.

No CD is in the magazine.

CDs are inserted incorrectly.

• “NO DISC” appears on the

display.

Connect this unit and the CD

changer correctly and press the

reset button of the CD changer.

This unit is not connected to a

CD changer correctly.

• “RESET 8” appears on the

display.

Press the reset button of the

CD changer.

• “RESET 1” - “RESET 7”

appears on the display.

• This unit does not work at all.

• The CD changer does not

work at all.

The built-in microcomputer may

function incorrectly due to

noise, etc.

Press the reset button on the

panel holder. (The clock setting

and preset stations stored in

memory are erased.)

(See page 2.)

SPECIFICATIONS

CASSETTE DECK SECTION

AUDIO AMPLIFIER SECTION

Maximum Power Output:

Wow & Flutter: 0.11% (WRMS)

Fast-Wind Time: 100 sec. (C-60)

Frequency Response (Dolby B NR OFF):

30 Hz to 16 000 Hz (Normal tape)

Signal-to-Noise Ratio: (Normal tape)

(Dolby B NR ON): 65 dB

Front: 50 W per channel

Rear: 50 W per channel

Continuous Power Output (RMS):

Front: 19 W per channel into 4 Ω, 40 Hz to

20 000 Hz at no more than

0.8 % total harmonic distortion.

Rear: 19 W per channel into 4 Ω, 40 Hz to

20 000 Hz at no more than

(Dolby B NR OFF): 56 dB

Stereo Separation: 40 dB

0.8 % total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)

Tone Control Range:

GENERAL

Power Requirement:

Bass: ±10 dB at 100 Hz

Treble: ±9 dB at 10 kHz

Operating Voltage: DC 14.4 V

(11 V to 16 V allowance)

Grounding System: Negative ground

Allowable Operating Temperature:

0°C to +40°C (32°F to 104°F)

Dimensions (W x H x D):

Frequency Response: 40 Hz to 20 000 Hz

Signal-to-Noise Ratio: 70 dB

Line-Out Level/Impedance:

2.0 V/20 kΩ load (250 nWb/m)

Installation Size:

TUNER SECTION

Frequency Range:

182 mm x 52 mm x 150 mm

(7-3/16" x 2-1/16" x 6-3/8")

Panel Size: 188 mm x 58 mm x 14 mm

(7-7/16" x 2-5/16" x 11/16")

Mass: 1.3 kg (2.9 lbs) (excluding accessories)

FM: 87.5 MHz to 107.9 MHz

AM: 530 kHz to 1 710 kHz

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)

50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75 Ω)

Design and specifications subject to change without

notice.

Alternate Channel Selectivity (400 kHz):

65 dB

Frequency Response: 40 Hz to 15 000 Hz

Stereo Separation: 35 dB

Capture Ratio: 1.5 dB

If a kit is necessary for your car, consult your

telephone directory for the nearest car audio

speciality shop.

[AM Tuner]

Sensitivity: 20 µV

Selectivity: 35 dB

http://www

.jvcmobile.com

Visit us on-line for

Technical Support & Customer Satisfaction Survey.

US RESIDENTS ONLY

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to Reset

Still having trouble??

USA ONLY

Call 1-800-252-5722

http://www.jvc.com

We can help you!

VICTOR COMPANY OF JAPAN, LIMITED

EN, SP, FR

0102KKSMDTJEIN

KS-FX480

Installation/Connection Manual

Manual de instalación/conexión

Manuel d’installation/raccordement

0102KKSMDTJEIN

EN, SP, FR

GET0068-002A

[J]

ENGLISH

ESPAÑOL

FRANÇAIS

• This unit is designed to operate on 12 V DC, NEGATIVE ground • Esta unidad está diseñada para funcionar con 12 V de CC, con • Cet appareil est conçu pour fonctionner sur des sources de

electrical systems.

sistemas eléctricos de masa NEGATIVA.

courant continu de 12 V à masse NEGATIVE.

INSTALLATION (IN-DASH

MOUNTING)

INSTALACION (MONTAJE EN EL

TABLERO DE INSTRUMENTOS)

INSTALLATION (MONTAGE DANS LE

TABLEAU DE BORD)

• The following illustration shows a typical installation. However, • La siguiente ilustración muestra una instalación típica. Sin • L’illustration suivante est un exemple d’installation typique.

you should make adjustments corresponding to your specific

car. If you have any questions or require information regarding

installation kits, consult your JVC car audio dealer or a company

supplying kits.

embargo usted deberá efectuar los ajustes correspondientes

a su automóvil. Si tiene alguna pregunta o necesita información

acerca de las herramientas para instalación, consulte con su

concesionario de JVC de equipos de audio para automóviles o

a una compañía que suministra tales herramientas.

Cependant, vous devez faire les ajustements correspondant à

votre voiture particulière. Si vous avez des questions ou avez

besoin d’information sur des kits d’installation, consulter votre

revendeur d’autoradios JVC ou une compagnie

d’approvisionnement.

1 Before mounting: Press

(Control Panel Release button)

to detach the control panel if already attached.

1 Antes de instalar: Pulse

(botón de liberación del panel

de control) para desenganchar el panel de control, si ya

está fijado.

1 Avant le montage: Appuyer sur

(dèblocage du

panneau de commande) pour èventeullement détacher

le panneau de commande.

* When shipped from the factory, the control panel is packed

in the hard case.

* El panel de control se expide de fábrica dentro del

estuche duro.

* Lorsque ce panneau de commande sort d’usine, il est

rangé dans un étui de transport.

2 Remove the trim plate.

3 Remove the sleeve after disengaging the sleeve locks.

1 Stand the unit.

2 Retire la placa de guarnición.

2 Retirer la plaque d’assemblage.

3 Libérer les verrous du manchon et retirer le manchon.

1 Poser l’appareil à la verticale.

3 Retire la cubierta después de desenganchar los retenes de

la cubierta.

Note: When you stand the unit, be careful not to damage

the fuse on the rear.

1 Ponga la unidad vertical.

Remarque: Lorsque vous mettez l’appareil à la

verticale, faire attention de ne pas endommager le

fusible situé sur l’arrière.

Nota: Al poner la unidad vertical, tenga cuidado de no

dañar el fusible provisto en la parte posterior.

2 Insert the 2 handles between the unit and the sleeve, as

illustrated, to disengage the sleeve locks.

2 Inserte las dos manijas entre la unidad y la cubierta tal

como en la ilustración y desenganche los retenes de la

cubierta.

3 Remove the sleeve.

2 Insérer les 2 poignées entre l’appareil et le manchon

comme indiqué pour désengagé les verrous de

manchon.

Note: Be sure to keep the handles for future use after

installing the unit.

3 Retire la cubierta.

3 Retirer le manchon.

4 Install the sleeve into the dashboard.

Nota: Después de instalar la unidad, asegúrese de

guardar las manijas para uso futuro.

Remarque: S’assurer de garder les poignées pour une

utilisation ultérieur, après l’’installation de l’appareil.

* After the sleeve is correctly installed in the dashboard, bend

the appropriate tabs to hold the sleeve firmly in place, as

illustrated.

4 Instale la cubierta en el tablero de instrumentos.

4 Installer le manchon dans le tableau de bord.

* Después de que la cubierta esté correctamente instalada

en el tablero de instrumentos, doble las lengüetas

correspondientes para sostener la cubierta firmemente en

su lugar, tal como se muestra.

* Après installation correcte du manchon dans le tableau

de bord, plier les bonnes pattes pour maintenir

fermement le manchon en place, comme montré.

5 Fix the mounting bolt to the rear of the unit’s body and place

the rubber cushion over the end of the bolt.

6 Do the required electrical connections.

7 Slide the unit into the sleeve.

8 Attach the trim plate.

5 Monter le boulon de montage sur l’arrière du corps de

l’appareil puis passer l’amortisseur en caoutchouc sur

l’extrémité du boulon.

5 Fije el perno de montaje en la parte trasera del cuerpo de la

unidad y coloque el cojín de goma sobre el extremo del

perno.

6 Réalisez les connexions électriques.

9 Attach the control panel.

6 Realice las conexiones eléctricas requeridas.

7 Faites glisser l’appareil dans le manchon jusqu’à ce qu’il

7 Deslice la unidad dentro de la cubierta hasta que quede

soit verrouillé.

trabada.

8 Attachez la plaque d’ajustage.

9 Remonter le panneau de commande.

8 Coloque la placa de guarnición.

9 Coloque el panel de control.

Control panel

Panel de control

Panneau de commande

Trim plate

Placa de guarnición

Plaque d’assemblage

Dashboard

Tablero de instrumentos

Tableau de bord

Rubber cushion

Cojín de goma

Amortisseur en caoutchouc

Handle

Manija

Poignée

184 mm

(7 – 1/4")

53 mm

Lock Plate

Placa de bloqueo

Plaque de verrouillage

(2 – 1/8")

Sleeve

Cubierta

Manchon

Mounting bolt

Perno de montaje

Boulon de montage

Slot

Ranura

Fente

Fuse

Fusible

See “ELECTRICAL CONNECTIONS.”

Véase “CONEXIONES ELECTRICAS”.

Référez-vous “RACCORDEMENTS

ELECTRIQUES” .

Sleeve

Cubierta

Manchon

Trim plate

Placa de guarnición

Plaque d’assemblage

Control panel

Panel de control

Panneau de commande

•When installing the unit without using the sleeve

•Instalación de la unidad sin utilizar la cubierta

•When using the optional stay

•Cuando emplea un soporte opcional

•Lors de l’utilisation du hauban en option

•Lors de l’installation de l’appareil sans utiliser de manchon

In a Toyota for example, first remove the car radio and install the unit in its place.

En un Toyota por ejemplo, primero extraiga la radio del automóvil y luego instale la unidad en su lugar.

Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.

Fire wall

Tabique a prueba de incendios

Cloison

Flat type screws (M5 x 6 mm)*

* Not included with this unit.

Washer

Arandela

Rondelle

Tornillos tipo plano (M5 x 6 mm)*

* No suministrado con esta unidad.

Stay (option)

Soporte (opción)

Hauban (en option)

Vis à tête plate (M5 x 6 mm)*

* Non fourni avec cet appareil.

Bracket*

Ménsula*

Support*

Dashboard

Lock nut

Tuerca de seguridad

Ecrou d’arrêt

Tablero de instrumentos

Tableau de bord

Flat type screws (M5 x 6 mm)*

Tornillos tipo plano (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Pocket

Compartimiento

Poche

Bracket*

Ménsula*

Support*

Screw (option)

Tornillo (opción)

Vis (en option)

Sleeve

Cubierta

Manchon

Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If longer

screws are used, they could damage the unit.

Nota: Cuando instala la unidad en la ménsula de montaje, asegúrese de utilizar los tornillos de

6 mm de longitud. Si se utilizan tornillos más largos, éstos pueden dañar la unidad.

Mounting bolt

Perno de montaje

Boulon de montage

Remarque: Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une

longueur de 6 mm. Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Removing the unit

Extracción de la unidad

Retrait de l’appareil

• Before removing the unit, release the rear section.

• Antes de extraer la unidad, libere la sección trasera.

• Avant de retirer l’appareil, libérer la section arrière.

1 Remove the control panel.

1 Extraiga el panel de control.

1 Retirer le panneau de commande.

2 Remove the trim plate.

2 Retire la placa de guarnición.

2 Retirer la plaque d’assemblage.

3 Insert the 2 handles into the slots, as shown.Then, while gently 3 Inserte las 2 manijas entre las ranuras, como se muestra.

3 Introduire les deux poignées dans les fentes, comme montré.

Puis, tout en tirant doucement les poignées écartées, faire

glisser l’appareil pour le sortir. (S’assurer de conserver les

poignées après l’installation de l’appareil.)

pulling the handles away from each other, slide out the unit.

Luego, separe shavemente las manijas y extraiga la unidad.

(Asegúrese de conservar las manijas después de

instalarlo.)

(Be sure to keep the handles after installing it.)

Control panel

Panel de control

Panneau de commande

Trim plate

Placa de guarnición

Plaque d’assemblage

Handle

Manija

Poignée

Parts list for installation and connection

The following parts are provided with this unit.

After checking them, please set them correctly.

Lista de piezas para instalación y conexión

Con esta unidad se suministran las siguientes piezas.

Después de inspeccionarlas, colóquelas correctamente.

Liste des pièces pour l’installation et

raccordement

Les pièces suivantes sont fournies avec cet appareil.

Après vérification, veuillez les placer correctement.

Hard case/Control panel

Estuche duro/Panel de control

Etui de transport/Panneau de

commande

Sleeve

Cubierta

Manchon

Trim plate

Placa de guarnición

Plaque d’assemblage

Remote controller

Control remoto

Télécommande

Battery

Pila

Pile

CR2025

Power cord

Cordón de alimentación

Cordon d’alimentation

Handles

Manijas

Poignées

Washer (ø5)

Arandela (ø5)

Rondelle (ø5)

Lock nut (M5)

Tuerca de seguridad (M5)

Ecrou d’arrêt (M5)

Mounting bolt (M5 x 20 mm)

Perno de montaje (M5 x 20 mm)

Boulon de montage (M5 x 20 mm)

Rubber cushion

Cojín de goma

Amortisseur en caoutchouc

ELECTRICAL CONNECTIONS

CONEXIONES ELECTRICAS

RACCORDEMENTS ELECTRIQUES

To prevent short circuits, we recommend that you disconnect the Para evitar cortocircuitos, recomendamos que desconecte el Pour éviter tout court-circuit, nous vous recommandons de

battery’s negative terminal and make all electrical connections terminal negativo de la batería y que efectúe todas las conexiones débrancher la borne négative de la batterie et d’effectuer tous les

before installing the unit. If you are not sure how to install this unit eléctricas antes de instalar la unidad. Si usted no está seguro de raccordements électriques avant d’installer l’appareil. Si l’on n’est

correctly, have it installed by a qualified technician.

cómo instalar correctamente la unidad, hágala instalar por un pas sûr de pouvoir installer correctement cet appareil, le faire installer

técnico cualificado.

par un technicien qualifié.

Note:

Nota:

Remarque:

This unit is designed to operate only on 12 V DC, NEGATIVE

ground electrical systems. If your vehicle does not have this

system, a voltage inverter is required, which can be purchased at

JVC car audio dealers.

Esta unidad está diseñada para funcionar con 12 V de CC, con

sistemas eléctricos de masa NEGATIVA solamente. Si su vehículo

no posee este sistema, será necesario un inversor de tensión, que

puede ser adquirido en los concesionarios de JVC de equipos de

audio para automóviles.

• Reemplace el fusible por uno con la corriente especificada. Si el

fusible se quemase frecuentemente consulte con su

concesionario de JVC de equipos de audio para automóviles.

• Si el ruido fuese un problema...

Esta unidad tiene un filtro de ruido en el circuito de alimentación.

Sin embargo, en algunos vehículos, pueden producirse

chasquidos u otros ruidos indeseados. En tal caso conecte el

terminal de tierra posterior (véase diagrama de conexión) del

receptor al chasis del automóvil, utilizando cordones más gruesos

y cortos tales como alambre de cobre trenzado o de grueso

calibre. Si el ruido persiste, consulte a su concesionario de JVC

de equipos de audio para automóvil.

• La entrada máxima de los altavoces traseros no debe ser no

más que 50 W en el trasero y 50 W en la frontal, con una

impedancia de 4 Ω a 8 Ω.

• Asegúrese de conectar esta unidad a tierra en el chasis del

automóvil.

• El sumidero térmico estará muy caliente después del uso.

Asegúrese de no tocarlo al desmontar esta unidad.

Cet appareil est conçu pour fonctionner sur des sources de courant

continu de 12 V à masse NEGATIVE seulement. Si votre véhicule

n’offre pas ce type d’alimentation, il vous faut un convertisseur de

tension, que vous pouvez acheter chez un revendeur d’autoradios

JVC.

• Replace the fuse with one of the specified rating. If the fuse

blows frequently, consult your JVC car audio dealer.

• If noise is a problem...

This unit incorporates a noise filter in the power circuit.However,

with some vehicles, clicking or other unwanted noise may occur.

If this happens, connect the unit’s rear ground terminal (see

connection diagram) to the car’s chassis using shorter and thicker

cords, such as copper braiding or gauge wire. If noise still

persists, consult your JVC car audio dealer.

• Maximum input of the speakers should be no more than 50 W at

the rear and 50 W at the front, with an impedance of 4 Ω to 8 Ω.

• Be sure to ground this unit to the car’s chassis.

• The heat sink becomes very hot after use. Be careful not to

touch it when removing this unit.

• Remplacer le fusible par un de la valeur précisée.Si le fusible saute

souvent, consulter votre revendeur d’autoradios JVC.

• Si le bruit est un problème...

Cet appareil incorpore un filtre de bruit dans le circuit d’alimentation.

Cependant, avec certains véhicules, quelques claquements ou

autres bruits non désirés risquent de se produire. Si cela arrive,

raccorder la borne arrière de masse de l’appareil au châssis de

la voiture (voir le schéma de raccordement) en utilisant des cordons

les plus gros et les plus courts possibles telle qu’une barre de cuivre

ou une tresse. Si le bruit persiste, consulter votre revendeur

d’autoradios JVC.

• La puissance admissible des enceintes devrait n’être pas plu qu’c

50 W à l’arrière et à 50 W l’avant, avec une impédance de 4 Ω à 8 Ω.

• S’assurer de raccorder la mise à la masse de cet appareil au

châssis de la voiture.

• Le dissipateur de chaleur devient très chaud après usage. Faire

attention de ne pas le toucher en retirant cet appareil.

Heat sink

Sumidero térmico

Dissipateur de chaleur

ENGLISH

ESPAÑOL

FRANÇAIS

A Typical Connections / Conexiones típicas / Raccordements typiques

Antes de la conexión: Verifique atentamente el conexionado del

Avant de commencer la connexion: vérifiez attentivement le

câblage du véhicule pour ne pas connecter incorrectement cet

appareil. Une connexion incorrecte peut endommager

sérieusement l’appareil.

Before connecting: Check the wiring in the vehicle carefully not

to fail in connecting this unit. Incorrect connection may cause a

serious damage to this unit.

vehículo para no cometer errores al conectar esta unidad. Una

conexión incorrecta podría producir daños graves en la unidad.

Los cordones del cable de alimentación y los del conector

The leads of the power cord and those of the connector from the

car body may be different in colour.

procedentes de la carrocería del automóvil podrían ser de Le fil du cordon d’alimentation et ceux des connecteurs du châssis

diferentes en color.

de la voiture peuvent être différents en couleur.

1 Connect the colored leads of the power cord to the car battery,

speakers and automatic antenna (if any) in the following

sequence.

1 Conecte los conductores de color del cable de alimentación 1 Connectez les fils de couleur du cordon d’alimentation à la

a la batería del automóvil, altavoces y antena automática (si

la hubiere) en la secuencia siguiente.

batterie de la voiture, aux enceintes et à l’antenne automatique

(s’il y en a une) dans l’ordre suivant.

1 Black: ground

1 Negro: a tierra

1 Noir: a la masse

2 Yellow: to car battery (constant 12 V)

3 Red: to an accessory terminal

2 Amarillo: a la batería del automóvil (12 V constantes)

3 Rojo: a un terminal de accesorio

2 Jaune: a la batterie de la voiture (12 Vconstant)

3 Rouge: à la prise accessoire

4 Blue with white stripe: to automatic antenna (250 mA

4 Azul con rayas blancas: a la antena automática (250 mA

4 Bleu avec bande blanche: à l’antenne automatique (250

max.)

máx.)

mA max.)

5 Orange with white stripe: to car light control switch

5 Naranja con rayas blancas: al interruptor de control de

5 Orange avec bande blanche: à l’interrupteur d’éclairage

las luces del automóvil

de la voiture

6 Others: to speakers

6 Autres fils: aux enceintes

6 Otros: a los altavoces

2 Connect the antenna cord.

2 Connectez le cordon d’antenne.

2 Conecte el cable de antena.

3 Finally connect the wiring harness to the unit.

3 Por último, conecte a la unidad el cableado preformado.

3 Finalement, connectez le faisceau de fils à l’appareil.

CAUTION/PRECAUTION/ATTENTION:

When connecting a CD changer, we recommend to use one of the CH-X series CD changers.

• If your CD changer is one of the KD-MK series, you need an optional cord (KS-U15K).

You can also use an external component such as a portable MD player by connecting the Line Input Adaptor KS-U57 (not supplied).

(See diagram B .)

•

Before connecting the CD changer, make sure that the unit is turned off.

Antes de conectar el cambiador de CD, asegúrese de que la unidad está

apagada.

•

Avant de connecter le changeur CD, assurez-vous que mettre l’appareil hors

tension.

Recomendamos conectar uno de los cambiadores de CD de la serie CH-X.

• Si su cambiador de CD es de la serie KD-MK, necesitará un cable opcional (KS-U15K).

Conectando el adaptador de entrada de línea KS-U57 (no suministrado), también podrá usar un componente exterior, tal como un

reproductor de MD. (Véase diagrama B .)

Lors de la connexion d’un changeur CD, nous vous recommandons d’utiliser un des changeurs CD de la série CH-X.

• Si votre changeur appartient à la série KD-MK, vous avez besoin d’un cordon optionnel (KS-U15K).

Vous pouvez aussi utiliser un appareil extérieur tel qu’un lecteur de MD en connectant l’adaptateur d’entrée de ligne KS-U57 (non

fourni) (voir le diagramme B .)

JVC CD changer or another external component

Cambiador de CD u otro componente exterior

Changeur CD JVC ou autre appareil extérieur

Rear ground terminal

Terminal de tierra

posterior

Borne arrière de

masse

15 A fuse

Fusible de 15 A

Fusible 15 A

Not supplied with this unit.

No suministrado con esta unidad.

Interruptor de encendido

Non fourni avec cet appareil.

Ignition switch

LINE OUT

(see diagram B )

Salida de linea

(véase diagrama B )

Sortie de ligne

Interrupteur d’allumage

Antenna terminal

Terminal de la antena

Borne de l’antenne

Black

Negro

Noir

To metallic body or chassis of the car

A un cuerpo metálico o chasis del automóvil

Au corps métallique ou châssis de la voiture

(voir le diagramme B )

Yellow*¹

Amarillo*¹

Jaune*¹

A la antena

A l’antenne

To a live terminal in the fuse block connecting to the car battery

(bypassing the ignition switch)

A un terminal activo del bloque de fusibles conectado a la

batería del automóvil (desviando el interruptor de encendido)

À une borne sous tension du porte-fusible connectée à la batterie

de la voiture (en dérivant l’interrupteur d’allumage)

To antenna

Red

Rojo

Rouge

Fuse block

Bloque de fusibles

Porte-fusible

To an accessory terminal in the fuse block

A un terminal accesorio del bloque de fusibles

À la prise accessoire du porte-fusible

*1: Before checking the operation of this unit prior to

installation, this lead must be connected, otherwise

power cannot be turned on.

Blue with white stripe

Azul con rayas blancas

Bleu avec bande blanche

*1: Antes de comprobar el funcionamiento de esta

unidad previa a la instalación, es necesario conectar

este cable, de lo contrario no se podrá conectar la

alimentación.

To automatic antenna if any

A la antena automática si la hubiere

À l’antenne automatique s’il y en a une

*1: Pour vérifier le fonctionnement de cet appareil avant

installation, ce fil doit être raccordé, sinon l’appareil

ne peut pas être mis sous tension.

To car light control switch

Al interruptor de control

de las luces del automóvil

À l’interrupteur d’éclairage

de la voiture

Orange with white stripe / Naranja con rayas blancas / Orange avec bande blanche

White with black stripe

Blanco con rayas negras

Blanc avec bande noire

White

Blanco

Blanc

Gray with black stripe

Gris con rayas negras

Gris avec bande noire

Gray

Gris

Green with black stripe

Verde con rayas negras

Vert avec bande noire

Green Purple with black stripe

Purple

Púrpura

Violet

Verde

Púrpura con rayas negras

Violet avec bande noire

Vert

Right speaker (front)

Altavoz derecho (frontal)

Enceinte droit (avant)

Left speaker (rear)

Altavoz izquierdo (trasero)

Enceinte gauche (arrière)

Left speaker (front)

Altavoz izquierdo (frontal)

Enceinte gauche (avant)

Right speaker (rear)

Altavoz derecho (trasero)

Enceinte droit (arrière)

PRECAUTIONS on power supply and speaker

connections:

PRECAUCIONES sobre las conexiones de la

fuente de alimentación y de los altavoces:

PRECAUTIONS sur l’alimentation et la

connexion des enceintes:

• DO NOT connect the speaker leads of the power cord to the • NO conecte los conductores de altavoz del cable de • NE CONNECTEZ PAS les fils d’enceintes du cordon

car battery; otherwise, the unit will be seriously damaged.

• Connect the black lead (ground), yellow lead (to car battery,

alimentación a la batería de automóvil, pues podrían

producirse graves daños en la unidad.

d’alimentation à la batterie; sinon, l’appareil serait

sérieusement endommagé.

constant 12V), and red lead (to an accessory terminal) correctly. • Conecte correctamente el conductor negro (a tierra), el • Connectez correctement le fil noir (a la masse), le fil jaune (a la

• BEFORE connecting the speaker leads of the power cord to the

speakers, check the speaker wiring in your car.

– If the speaker wiring in your car is as illustrated in Fig. 1 • ANTES de conectar a los altavoces los conductores de altavoz • AVANT de connecter les fils d’enceintes du cordon

conductor amarillo (a la batería del automóvil, 12 V constantes),

y el conductor rojo (a un terminal de accesorio).

batterie de la voiture,12 V constant) et le fil rouge (à la prise

accessoire).

and Fig. 2 below, DO NOT connect the unit using that original

speaker wiring. If you do, the unit will be seriously damaged.

Redo the speaker wiring so that you can connect the unit to

the speakers as illustrated in Fig. 3.

– If the speaker wiring in your car is as illustrated in Fig. 3, you

can connect the unit using the original speaker wiring in your car.

– If you are not sure of the speaker wiring of your car, consult

your car dealer.

del cable de alimentación, verifique el conexionado de altavoz

de su automóvil.

d’alimentation aux enceintes, vérifiez le câblage des enceintes

de votre voiture.

– Si el conexionado de altavoz de su automóvil es como

se indica en las Fig. 1 y Fig. 2 de abajo, NO conecte la

unidad utilizando ese conexionado de altavoz original. Si lo

hace, se producirán daños graves en la unidad.

Vuelva a efectuar el conexionado de altavoz de manera que

pueda conectar la unidad a los altavoces de la manera

indicada en la Fig.3.

– Si el conexionado de altavoz de su automóvil es como

se indica en la Fig. 3, podrá conectar la unidad utilizando

el conexionado de altavoz original de su automóvil.

– Si tiene dudas sobre el conexionado de altavoz de su

automóvil, consulte con su concesionario.

– Si le câblage des enceintes de votre voiture est réalisé

comme montré sur la Fig. 1 ou Fig. 2 ci-dessous, NE

CONNECTEZ PAS l’appareil en utilisant ce câblage original

d’enceintes. Si vous le faites, l’appareil sera sérieusement

endommagé.

Recommencez le câblage des enceintes de façon que vous

puissiez connecter l’appareil aux enceintes comme montré

sur la Fig. 3.

– Si le câblage des enceintes de votre voiture est comme

montré sur la Fig. 3, vous pouvez connecter l’appareil en

utilisant ce câblage original d’enceintes pour votre voiture.

– Si vous n’êtes pas sûrs du câblage d’enceintes de votre

voiture, consulter le concessionnaire de votre voiture.

Fig. 1

Fig. 2

Fig. 3

Connecting the leads / Conexión de los conductores / Raccordement des fils

Twist the core wires when connecting.

CAUTION / PRECAUCION / PRECAUTION:

Retuerza los alambres de alma para conectarlos.

•

To prevent short-circuit, cover the terminals of the UNUSED leads with insulating

tape.

Torsader les âmes des fils en les raccordant.

•

Para evitar cortocircuitos, cubra los cables NO UTILIZADOS con cinta aislante.

Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS utilisés

avec de la bande isolante.

Solder the core wires to connect them

securely.

Suelde los alambres de alma para

conectarlos con firmeza.

Souder les âmes desfils pour les raccorder

entre eux de façon sûre.

B Connections Adding Other Equipment / Conexiones para añadir otros equipos / Raccordement pour ajouter d’autres appareils

You can connect an amplifier and other equipment to upgrade your car Usted podrá conectar un amplificador y otros equipos para mejorar el

stereo system. sistema estéreo de su automóvil.

• Connect the remote lead (blue with white stripe) to the remote lead of • Conecte el conductor remoto (azul con rayas blancas) al conductor

Vous pouvez connecter un amplificateur ou autre appareil pour améliorer

votre système autoradio.

• Connectez le fil de commande à distance (bleu avec bande blanche) au

fil de commande à distance de l’autre appareil de façon qu’il puisse être

commandé via cet appareil.

the other equipment so that it can be controlled through this unit.

remoto del otro equipo para poderlo controlar a través de esta unidad.

• For amplifier:

• Para el amplificador:

– Connect this unit’s line-out terminals to the amplifier’s line-in terminals.

– Disconnect the speakers from this unit, connect them to the

amplifier. Leave the speaker leads of this unit unused.

(Cover the terminals of the these unused leads with insulating

tape, as illustrated above.)

– Conecte los terminales de salida de línea de esta unidad a los

terminales de entrada de línea del amplificador.

– Desconecte los altavoces de esta unidad y conéctelos al

amplificador. Deje los conductores de los altavoces de esta

unidad sin usar. (Cubra los terminales de estos cables sin

usar con cinta aislante, tal comose indica en la figura de

arriba.)

• Pour l’amplificateur:

– Raccorder les fiches de sortie ligne de cet appareil aux fiches d’entrée

ligne de l’amplificateur.

– Déconnectez les enceintes de cet appareil et connectez-les à

l’amplificateur. Laissez les fils d’enceintes de cet appareil inutilisés.

(Recouvrir les extrémités de ces inutilisés avec de la bande comme

montre dessus.)

Amplifier / Amplificador / Amplificateur

Rear speakers

Altavoces traseros

Enceintes arrière

Remote lead

Cable remoto

Fil d’alimentation à distance

Y-connector (not supplied with this unit)

Conector en Y (no suministrado con esta unidad)

Connecteur Y (non fourni avec cet appareil)

INPUT

JVC Amplifier

Amplificador de JVC

Amplificateur JVC

Remote lead (Blue with white stripe)

Cable remoto (Azul con rayas blancas)

Fil d’alimentation à distance (Bleu avec bande blanche)

To automatic antenna if any

A la antena automática, si la

hubiere

Vers l’antenne automatique, s’il y

en a une

Signal cord (not supplied with this unit)

Cable de señal (no suministrado con esta unidad)

Cordon de signal (non fourni avec cet appareil)

LINE OUT

(FRONT)

LINE OUT

(REAR)

LINE OUT

INPUT

Front speakers

Altavoces delanteros

JVC Amplifier

Amplificador de JVC

Amplificateur JVC

REAR FRONT

Haut-parleur avant

Vous pouvez connecter un

Podrá conectar otro

amplificador

de potencia para los

altavoces delanteros.

You can connect another

power amplifier for front

speakers.

autre amplificateur de

puissance pour les enceintes

avant.

KS-FX480

Front speakers

Altavoces delanteros

Haut-parleur avant

*2 Firmly attach the ground wire to the metallic body or to the chasis of the car—to the place not coated with paint (if coated with paint, remove the paint

before attaching the wire). Failure to do so may cause damage to the unit.

*2 Fije firmemente el cable de tierra a la carrocería metálica o al chasis—a un lugar no cubierto con pintura (si está cubierto con pintura, quítela antes de

fijar el cable). De lo contrario, se podrían producir daños en la unidad.

*2 Attachez solidement le fil de mise à la masse au châssis métallique de la voiture—à un endroit qui n’est pas recouvert de peinture (s’il est recouvert de

peinture, enlevez d’abord la peinture avant d’attacher le fil). L’appareil peut être endommagé si cela n’est pas fait correctement.

External component / Componente exterior / Appareil extérieur

LINE OUT

KS-FX480

REAR FRONT

Line Input Adaptor KS-U57 (not supplied with this unit)

Adaptador de entrada de línea KS-U57 (no suministrado con esta unidad)

Adaptateur d’entrée de ligne KS-U57 (non fourni avec cet appareil)

External component

Componente exterior

Appareil extérieur

Signal cord (not supplied with this unit)

Cable de señal (no suministrado con esta unidad)

Cordon de signal (non fourni avec cet appareil)

CD changer jack

Toma del cambiador de CD

Prise du changeur CD

TROUBLESHOOTING

• The fuse blows.

LOCALIZACION DE AVERIAS

• El fusible se quema.

EN CAS DE DIFFICULTES

• Le fusible saute.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

* ¿Están los conductores rojo y negro correctamente conectados?

• No es posible conectar la alimentación.

* ¿Está el cable amarillo conectado?

* Les fils rouge et noir sont-ils racordés correctement?

• L’appareil ne peut pas être mise sous tension.

* Le fil jaune est-elle raccordée?

• No sound from the speakers.

• No sale sonido de los altavoces.

• Pas de son des enceintes.

* Is the speaker output lead short-circuited?

• Sound is distorted.

* ¿Está el cable de salida del altavoz cortocircuitado?

• El sonido presenta distorsión.

* Le fil de sortie de d’enceinte est-il court-circuité?

• Le son est déformé.

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded in common?

• Unit becomes hot.

* ¿Está el cable de salida del altavoz conectado a masa?

* ¿Están los terminales “–” de los altavoces L y R conectados a una * Les bornes “–” des enceintes gauche et droit sont-elles mises

masa común?

* Le fil de sortie de d’enceinte est-il à la masse?

ensemble à la masse?

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded in common?

• La unidad se calienta.

* ¿Está el cable de salida del altavoz conectado a masa?

• L’appareil devient chaud.

* Le fil de sortie de d’enceinte est-il à la masse?

* ¿Están los terminales “–” de los altavoces L y R conectados a una * Les bornes “–” des enceintes gauche et droit sont-elles mises

masa común? ensemble à la masse?

Memorex iWake Mi4004 User Manual
JVC KD S895 User Manual
Intel Chipper 945G User Manual
Honeywell PCR201W User Manual
DeLonghi Coffeemaker KG 79 89 User Manual
Dell POWEREDGE 2950 User Manual
Crosley Radio Memory Master Ii Cd Recorder CR2413A BK User Manual
Clarion DB356MP User Manual
Clarion DB238R User Manual
Black & Decker DLX1050B User Manual