R
SmartSet® Clock Radio
with Auto-Time Setting System,
Jumbo Display, Dual Alarms,
Sure Alarm, Time Projection System
and Rechargeable Flashlight
(U.S. Patent No. 6,567,344)
OWNER’S MANUAL
CKS3095B
CKS3095S
(Black Color)
(Silver Color)
CKS3095_041707.p65
36
17/4/2007, 16:06
Thank you for purchasing this Emerson SmartSet® Dual Alarm Clock Radio with
Time Projection System, and Rechargeable Flashlight.
This clock radio uses Emerson’s patented SmartSet® Automatic Time Setting
System. The first time you connect this clock radio to your AC outlet, and after
every power interruption, within seconds the clock will automatically set itself to
the correct Year, Month, Date, Day, and Time. You will never see that annoying,
flashing “12:00” display again. In addition all changes from Standard Time to Daylight
Saving Time, and back to Standard Time, are made automatically.
There are dual alarms that can be set and used independently, which means that
you can set one alarm to wake you to the buzzer and the other to wake you to
music. And both of the alarms can be programmed for everyday operation,
weekdays only, or weekends only.
This model also includes an integrated clock time projector that will project the
time in large RED numerals on the wall or ceiling of a dark room. This allows you
to see the time without actually looking at the clock itself. We’ve even included a
built-in rechargeable, removable flashlight that’s always ready to use whenever
you need it.
There is a long life lithium battery installed in this clock radio when you buy it. This
battery can maintain the time and alarm settings for 3 to 5 years, or even longer,
so there is no need to pay for a new 9-volt battery every 6 months, as is
recommended in other clock radios with normal battery back up.
We have taken every precaution to make sure this radio was in perfect working
order when it left our factory. If you encounter any problems with the set up or
operation of this item, please call the Emerson Consumer Products Corp., Customer
Service Hotline, toll free, at 1-800-898-9020.
Once again, thank you for purchasing this Emerson SmartSet® Clock Radio.
2
CKS3095_041707.p65
2
17/4/2007, 16:06
IMPORTANT NOTES
• Avoid installing this unit in places • Operate controls and switches as
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much
heat, places lacking ventilation or dusty
areas, places subject to constant
vibration and/or humid or moist areas.
described in the manual.
• Before turning on the power, make
certain that the AC power cord is
properly installed.
• When moving the set, be sure to first
disconnect the AC power cord.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequencyenergy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
3
CKS3095_041707.p65
3
17/4/2007, 16:06
PREPARATION FOR USE
Unpacking And Set Up
• Remove the flashlight and the radio from the carton and remove all packing
materials from both components. We suggest that you save the carton and
packing materials if possible in the event that your unit ever needs to be returned
for service. Using the original carton and packing materials is the only way to
protect your unit from damage in shipment.
• Place the flashlight in the charging cradle as shown. Push the back end of the
flashlight into the charging tube in the direction of the arrow as shown until the
front end of the flashlight is positioned behind the flashlight retaining tab. This
tab holds the flashlight in the charging tube. The flashlight must be held in this
position in order for charging to begin.
(Flashlight Retaining Tab)
IMPORTANT: The flashlight must be charged in the charging cradle
for 24 hours before initial use. When the radio is connected to the AC
outlet and the flashlight is properly positioned in the charging cradle
the Red “Charging” indicator in the flashlight AUTO /OFF switch
comes ‘on’.
4
CKS3095_041707.p65
4
17/4/2007, 16:06
• Remove any descriptive labels or stickers on the front or top of the cabinet. Do
not remove any labels or stickers from the back or bottom of the cabinet.
• Note the serial number on the bottom of your radio and write this number in
the space provided on the Warranty page of this manual.
• Place your radio on a level surface such as a table, desk or shelf, convenient
to an AC outlet, out of direct sunlight, and away from sources of excess heat,
dirt, dust, moisture, humidity, or vibration.
• Unwind the AC power cord and extend it to its full length. The FM antenna is
built in to this cord. It must be fully extended to provide the best FM reception.
Protect Your Furniture
This model is equipped with non-skid rubber ‘feet’ to prevent the product from
moving when you operate the controls. These ‘feet’ are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber ‘feet’ to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
5
CKS3095_041707.p65
5
17/4/2007, 16:06
Power Source
This radio is designed to operate on normal 120V 60Hz AC power only. Do not
attempt to operate the radio on any other power source. You could cause damage
to the radio that is not covered by your warranty.
This radio should be connected to an AC outlet that is always ‘live’. Do not connect
it to an outlet that is controlled by a wall switch. When the power to the radio is
interrupted, the built in lithium battery takes over to maintain the time and alarm
settings. To maximize the life of the lithium battery keep the radio connected to a
‘live’ AC outlet at all times.
You will note that this system is equipped with
a polarized AC power plug having one blade
wider than the other. This is a safety feature. If
this plug does not fit into your existingAC outlet,
do not try to defeat this safety feature by filing
the wide blade to make it fit into your outlet.
AC Outlet
If this plug will not fit into your outlet, you
AC Plug
probably have an out-dated non-polarized AC
outlet. You should have your outlet changed by
a qualified licensed electrician.
Sure Alarm battery Back-Up System
This SmartSet® Clock Radio includes a Sure Alarm battery back-up circuit that can
wake you up even if the power is ‘Off’ at the selected wake up time. If your power
is ‘Off’ at the selected wake up time the clock display will be off and the radio will
not operate, but a separate mini-buzzer will turn ‘On’ automatically to wake you up,
even if you had selected the “Wake to Radio” option.
The Sure Alarm will sound for 30 seconds and then shut off automatically.
To stop the Sure Alarm buzzer immediately, press the RADIO ON/OFF button.
Pressing the SNOOZE button has no effect during Sure Alarm operation.
Note: In order to maximize the life of the built in lithium battery, please be sure
to set the ALARM 1 and ALARM 2 switches to the “OFF” position if the radio
will be disconnected from the AC outlet for more than a few hours. This will
prevent the Sure Alarm from turning ‘On’ unnecessarily.
6
CKS3095_041707.p65
6
17/4/2007, 16:06
LOCATION OF CONTROLS AND INDICATORS
Front Panel
2
3
4
1
5
6
7
9
8
Top Panel
14
13
15
16
12
11
17
10
26
25 24 23 22 21 20 19
27
18
7
CKS3095_041707.p65
7
17/4/2007, 16:06
Front Panel
1.) Projector.
2.) AM Indicator.
3.) MON / TUE / WED / THU / FRI / SAT / SUN (Day Of Week) Indicators.
4.) Time/Date/Year/Radio Frequencies Display.
5.) WAVE SENSOR.
6.) AL 2 (Alarm 2 ‘On’) Indicator.
7.)
LOW (Battery Low) Indicator.
8.) Back Up Battery Compartment (Bottom Cabinet).
9.) AL 1 (Alarm 1 ‘On’) Indicator.
Top Panel
10.) Projector Lens.
11.) Flashlight AUTO (On)
/OFF
Button and Charger ‘On’ Indicator.
12.) Flashlight Retaining Tab.
13.) AC Power Cord (Back Cabinet).
14.) Rechargeable Flashlight.
15.) Flashlight Charging Tube.
16.) SET + Button.
17.) SET – Button.
18.)
RADIO ON/OFF Button.
19.) ALARM 2 setting Button.
20.) ALARM 1 setting Button.
21.) ALARM MODE (Weekdays / Weekends / Everyday Alarm) Button.
22.) TIME ZONE Button.
23.) TIME Setting Button.
24.) MONTH/DATE Setting Button.
25.) SLEEP Button (Sleep To Music Timer).
26.) PROJECTOR (On/Off) Button.
27.) SNOOZE Button.
8
CKS3095_041707.p65
8
17/4/2007, 16:06
Left Side Panel
29
30
31
28
33
32
Right Side Panel
36
35
34
37
38
9
CKS3095_041707.p65
9
17/4/2007, 16:06
Left Side Panel
28.) Display DIMMER (OFF/WAVE-LOW-HIGH) Selector Switch.
29.) Flashlight Lens.
30.) Projector FOCUS Adjustment Ring.
31.) Projector ROTATE IMAGE Selector Switch.
32.) ALARM 1 (RADIO/BUZZ/OFF) Selector Switch.
33.) ALARM 2 (RADIO/BUZZ/OFF) Selector Switch.
Right Side Panel
34.) TUN. (Tuning) Control.
35.) AM/FM Band Selector Switch.
36.) VOL. (Volume) Control.
37.) Speaker (Back Cabinet).
38.) Sure Alarm Buzzer (Back Cabinet).
10
CKS3095_041707.p65
10
17/4/2007, 16:06
OPERATING INSTRUCTIONS
Setting The Time, The First Time
IMPORTANT: The first time you connect your new SmartSet® clock radio to
the AC outlet the internal computer will automatically set the time correctly for
the Eastern Time Zone, which is the initial default setting.
The display will scan for a few seconds and then show the correct Day and Time in
the Eastern zone. If you live in the Eastern Time zone, there’s nothing else to do.
Your clock is set correctly and running.
If you do not live in the Eastern Time zone you must change the default zone
display to your own zone. You only do this one time and the SmartSet® will remember
the new default zone setting and will always return to that setting after a power
interruption.
There are 7 time zones programmed into your SmartSet® clock radio as follows:
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
ZONE 7
—
—
—
—
—
—
—
Atlantic Time
Eastern Time (Default Setting)
Central Time
Mountain Time
Pacific Time
Yukon Time
Hawaiian Time
To change the default time zone display, depress
the TIME ZONE button. The number “2” will
appear on the display indicating that the default
zone is ZONE 2, Eastern Time.
Hold the TIME ZONE button and then press either the SET + or – buttons until
your own time zone appears on the display, then release the buttons. The clock
display will change to the correct time in the time zone you selected. The clock will
always return to the correct time in the zone you selected after every power
interruption.
If you move to a different time zone, simply change the default zone display to the
new zone and the SmartSet® will remember that setting for you.
11
CKS3095_041707.p65
11
17/4/2007, 16:06
Date Display
To see the correctDate at any time, depress the MONTH/DATE button. The display
changes from Time to Month and Date (MM/DD).
For example, May 21st will appear as “5.21”.
When you release the MONTH/DATE button the
display returns to the correct Time.
Year Display
To see the correct Year, depress the
MONTH/DATE and TIME buttons together.
The display changes from Time to Year.
When you release the MONTH/DATE and TIME buttons the display returns to the
correct Time.
Daylight Saving and Leap Year Adjustments
All Daylight Saving and Leap Year adjustments are made automatically by
the SmartSet® internal computer as follows:
• Start of Daylight Saving Time:
At “2:00 AM” on the 2nd Sunday in March, the clock will automatically
advance to “3:00 AM”.
• End of Daylight Saving Time:
At “3:00 AM” on the 1st Sunday in November, the clock will automatically
reset to “2:00 AM”.
• Leap Year:
At “12:00 Midnight” on February 28th, the calendar display will change
to “2.29”.
12
CKS3095_041707.p65
12
17/4/2007, 16:06
Manual Time Adjustments
Some people like to set their clocks 5 to 10 minutes fast to make sure that they will
always be on time. Even though the SmartSet® sets the time by itself, you still have
the option of adjusting the time manually if you wish.
To manually adjust the time display depress and hold the TIME button, and press
either the SET + or – buttons to adjust the time display ahead or back as desired.
Each press of the SET + or – buttons will change the display by one minute. If you
hold the SET + or – buttons the display will continue to change. The display will
change slowly at first, one minute at a time. But if you continue holding the SET +
or – buttons the display will change rapidly.
Note: If you manually adjust the time, your new setting is entered into the
SmartSet® memory. If the power is interrupted, the display will return to your
new setting, not the original setting, when the power is restored.
13
CKS3095_041707.p65
13
17/4/2007, 16:06
Adjusting The Wake Up Times
Your SmartSet® clock radio has two separate alarms that can be set and used
independently. You may use the alarms to wake two people at different times, or
you may use one alarm for weekdays and the other for weekend wake up times.
The procedure for adjusting the wake up time is the same for both Alarm 1 and
Alarm 2.
1.) Depress and hold either the ALARM 1 or ALARM 2 setting button.
The display will change from the correct time
to the Alarm 1 or Alarm 2 wake up time.
2.) While holding the ALARM 1 or ALARM 2 setting button, depress either the
SET + or – button to move the display ahead or back to your desired wake up
time.
3.) When the desired wake up time appears on the display, release the SET + or
– buttons.
Note: Be sure that you have set the wake up time correctly by observing
the AM indicator. If the AM indicator is ‘On’ the wake up time is “AM”. If the
AM indicator is ‘Off’, the wake up time is “PM”.
4.) When the desired wake up time (AM or PM) appears on the display, release
the ALARM 1 or ALARM 2 setting buttons.
14
CKS3095_041707.p65
14
17/4/2007, 16:06
Selecting The Alarm Mode
Your SmartSet® clock radio allows you to select from among three different alarm
operation modes for either alarm. The alarm modes are:
• Everyday – the alarm will turn on all 7 days.
• Weekdays only – the alarm will only turn on Monday through Friday;
• Weekends only – the alarm will only turn on Saturday and Sunday;
To check the Alarm Mode setting for Alarm 1, depress the ALARM 1 setting button.
The display will show the Alarm 1 wake up time and the Day indicators will show
you the alarm mode which is selected.
• If all 7 indicators are ‘On’, the Everyday mode
is selected.
• If only the MON(Monday) through FRI(Friday)
indicators are ‘On’, the Weekdays only mode
is selected.
• If only the SAT(Saturday) and SUN(Sunday)
indicators are ‘On’, the Weekends only mode
is selected.
To change the Alarm Mode setting for Alarm 1, hold the ALARM 1 setting button
and press the ALARM MODE button until the Day indicators show the desired
mode setting, Weekdays only, Weekends only, or Everyday operation.
Release the ALARM MODE and ALARM 1 setting buttons and the display will
return to the correct time.
Follow the same procedure to select the desired Alarm Mode for Alarm 2 if
necessary.
Checking The Wake Up Times And Alarm Mode
Whenever you want to check the wake up time or the alarm mode settings, simply
press either the ALARM 1 or ALARM 2 setting buttons. The display will change
from “correct time” to “wake up time” and the Day indicators will show you the
alarm mode which is currently selected.
Release the ALARM 1 or ALARM 2 setting buttons to return to correct time.
15
CKS3095_041707.p65
15
17/4/2007, 16:06
Listening To The Radio
Digital Radio Frequency Display
This clock radio features a digital radio frequency display instead of a dial scale to
make tuning easier, especially in a dark room. The jumbo LED time display
automatically changes to a radio frequency display as soon as you begin turning
the TUN. (Tuning) control. And the display automatically changes back to the correct
time within 10 seconds after you release the TUN. (Tuning) control.
1.) Set the Band FM/AM selector switch to the desired band, AM or FM.
2.) Set the VOL. (Volume) control to a low setting.
3.) Press the
RADIO ON/OFF button to turn
the radio ‘On’. The display changes from time
to an AM or FM radio frequency display.
4.) Turn the TUN. (Tuning) control counter-clockwise to select higher numbered
frequencies or clockwise to select lower numbered frequencies.
Important: It is not necessary to tune to the exact frequency of your
desired station. Just rotate the TUN. (Tuning) control until you find
the strongest signal and the best reception, even if the frequency
number on the display is higher or lower than the actual station
frequency.
Within 10 seconds after you release the TUN. (Tuning) control the display
automatically changes back to the correct time.
5.) Adjust the VOL. (Volume) control to the desired setting.
6.) When you are finished listening, press the
the radio ‘Off’.
RADIO ON/OFF button to turn
16
CKS3095_041707.p65
16
17/4/2007, 16:06
Antenna Information
AM – The AM bar antenna is inside the cabinet. If AM reception is weak, change
the position of cabinet until the internal antenna picks up the strongest signal.
FM – The FM antenna is built in to the AC power cord. If FM reception is weak try
varying the position and direction of the AC power cord until you find the
strongest signal.
17
CKS3095_041707.p65
17
17/4/2007, 16:06
Wake To Radio
1.) Turn the radio ‘On’ and select the band, station, and volume level that you wish
to hear when the alarm comes ‘On’, then turn the radio ‘Off’ again.
2.) Reconfirm the wake up time and alarm mode settings for the alarm you are
using, Alarm 1, Alarm 2, or both alarms.
3.) Set the ALARM selector switch for one or both alarms to the “RADIO” position.
The appropriate AL 1 and/or AL 2 indicators will light up to confirm that the
alarms are set.
4.) At the selected wake up time the radio will turn ‘On’. It will play for one hour and
then shut off automatically.
5.) To stop the radio sooner, press either the appropriate ALARM 1 or ALARM 2
button, or press the
RADIO ON/OFF button. The radio will stop but the
alarm remains set and will turn the radio on again at the same time on the
following day (depending on the Alarm Mode setting).
6.) If you do not want the alarm to turn the radio on the following day, set the
appropriate ALARM selector switch to the “OFF” position.
18
CKS3095_041707.p65
18
17/4/2007, 16:06
Wake To Buzzer (Crescendo Alarm)
Note: Alarm 1 and Alarm 2 have different buzzer sounds.
• Alarm 1 is a “Single beep” sound.
• Alarm 2 is a “Double beep” sound.
You will be able to tell which alarm is going off by the sound that it makes.
1.) Reconfirm the wake up time and alarm mode settings for the alarm you are
using, Alarm 1, Alarm 2, or both alarms.
2.) Set the ALARM selector switch for one or both alarms to the BUZZ position.
The appropriate AL 1 and/or AL 2 indicators will light up to confirm that the
alarms are set.
3.) At the selected wake up time the buzzer will sound. It will begin softly and
gradually increase in volume to wake you up. It will continue for one hour and
then shut off automatically.
4.) To stop the buzzer sooner, press either the appropriate ALARM 1 or ALARM 2
button. The buzzer will stop but the alarm remains set and will turn the buzzer
on again at the same time on the following day.
(depending on the Alarm Mode setting).
To stop the buzzer and turn on the radio immediately, press the
RADIO
ON/OFF button instead of the ALARM 1 or ALARM 2 button.
5.) If you do not want the alarm to turn the buzzer on the following day, set the
appropriate ALARM selector to the “OFF” position.
19
CKS3095_041707.p65
19
17/4/2007, 16:06
Radio And Buzzer Operation
You may also set one alarm for wake to RADIO and the other for wake to BUZZER.
Just set the ALARM 1 and ALARM 2 selector switches to the desired positions.
20
CKS3095_041707.p65
20
17/4/2007, 16:06
Snooze Alarm
After the alarm turns ‘On’ in the morning you can use the Snooze function to grab
a few more minutes sleep before the alarm sounds again. To activate the Snooze
function you can press the SNOOZE button on the top cabinet.
The corresponding AL indicator will flash.
Touchless Snooze Control
You may also activate the Snooze Alarm without physically touching the SNOOZE
button by placing your hand in front of the WAVE SENSOR on the front panel.
See illustration.
The Touchless Snooze Control works by detecting body heat. For best results
your hand should be within 24 inches of the front panel.
21
CKS3095_041707.p65
21
17/4/2007, 16:06
Sleep To Music Timer
You can program the sleep timer to play the radio for up to 90 minutes and then
shut ‘Off’ automatically.
1.) Press the SLEEP button.
The display will briefly show “10” and the radio will begin to play.
After 10 minutes the radio will shut off
automatically. Each time you press the
SLEEP button the sleep timer will start at 10
minutes. This is the sleep timer default
setting.
2.) To increase or decrease the amount of time that the radio will play before
shutting off, hold the SLEEP button and press either the SET + or – button to
change the display to the desired sleep time, up to a maximum of “90” minutes
or a minimum of “02” minutes.
Note: When you change the sleep timer from the 10 minute default setting
to a different setting, the new setting becomes the default setting. Whenever
you activate the sleep timer it will begin with your new default setting and
count down to zero from that point.
3.) To cancel the sleep timer before it counts down to “00” and shut the radio ‘Off’
immediately, press the SNOOZE Bar.
IMPORTANT:
Remember that the station and volume settings you choose for the “Sleep To
Music” operation are the same settings you will hear if you set the alarm for
wake to radio the following morning.
22
CKS3095_041707.p65
22
17/4/2007, 16:06
Display Brightness Control
This SmartSet® Clock Radio features a unique display brightness control system
that gives you three convenient options:
• HIGH – when the DIMMER switch is set to the “HIGH” position the clock display
is always at full brightness. The DIMMER switch was set to the “HIGH” position
at our factory.
• LOW – when the DIMMER switch is set to the “LOW” position the display
brightness is reduced by approximately 50%.
• OFF/WAVE– when the DIMMER switch is set to the “OFF/WAVE” position the
display goes ‘Off’ completely. This is designed for people who prefer to sleep
in total darkness. However if you want to see the clock display at any time,
slowly wave your hand in front of the WAVE SENSOR on the front panel. The
clock display will immediately return to full brightness for 10 seconds and then
shut off again automatically. The effective operating range of the Wave Sensor
is approximately “12 in” to “36 in” from the front panel.
DIMMER Selector Set To
“OFF/WAVE” Position.
R
R
Wave Your Hand To Restore The Display
For 10 Seconds.
23
CKS3095_041707.p65
23
17/4/2007, 16:06
Time Projector Operation
IMPORTANT NOTES:
• The projected image of the time on your wall or ceiling is only visible
when the room lighting is ‘Off’ and the room is dark. The image will
not be visible when the room lights are ‘On’.
• If you experience a power interruption when the time projector is ‘On’,
the main display and the time projector will go ‘Off’. When power is
restored the main display will return to the correct time, but the time
projector will remain ‘Off’. You must press the PROJECTOR ‘On/Off’
button once more to switch the time projector ‘On’ again.
This is your indication that you experienced a power failure. If you
notice that the time display is no longer being projected on your wall
or ceiling this means that your power was interrupted, and although
the time on your SmartSet® clock will be correct you will probably
need to reset all of the other electronic clocks in your home.
1.) Switch off the room lights to darken the room.
2.) Press the PROJECTOR ‘On/Off’ button to turn the projector ‘On’.
3.) Turn the projector unit slowly to aim the projected image on the wall or ceiling.
“PROJECTOR” On/Off Button
24
CKS3095_041707.p65
24
17/4/2007, 16:06
4.) If the image appears to be upside down on your wall, or upside down on the
ceiling when you are lying in bed, set the ROTATE IMAGE switch to its alternate
position.
5.) If the image appears ‘fuzzy’ and out of focus, slowly rotate the FOCUS
adjustment ring clockwise or counter-clockwise until you obtain the sharpest
image.
6.) If you no longer wish to see the projected image, press the PROJECTOR ‘On/Off’
button to turn the projector ‘Off’.
25
CKS3095_041707.p65
25
17/4/2007, 16:06
Rechargeable Flashlight Operation
The flashlight must be properly placed in the cradle and inserted into the Charging
Tube for charging to begin.
Place the flashlight in the charging cradle as shown. Push the back end of the
flashlight into the charging tube in the direction of the arrow as shown until the
front end of the flashlight is positioned behind the flashlight retaining tab. This tab
holds the flashlight in the charging tube. The flashlight must be held in this position
in order for charging to begin.
1.) The flashlight is being placed in the cradle.
(Battery Charging Tube)
2.) The flashlight is being pushed into the
charging tube and locked in place behind
the flashlight retaining tab.
(Flashlight Retaining Tab)
IMPORTANT: The flashlight must be charged in the charging cradle for
24 hours before initial use. When the radio is connected to the AC outlet
and the flashlight is properly positioned in the charging cradle the Red
“Charging” indicator in the flashlight AUTO /OFF switch comes ‘on’.
26
CKS3095_041707.p65
26
17/4/2007, 16:06
Auto Operation
If the flashlight AUTO /OFF switch is left in the “AUTO ” position the flashlight
will turn on automatically when it is removed from the cradle. It will also turn on
automatically if the AC power is interrupted.
When you return the flashlight to the charging cradle, or when AC power is restored,
the flashlight will turn ‘Off’ automatically.
Manual Operation
If the flashlight AUTO /OFF switch is left in the “OFF ” position the flashlight
will remain off until you remove it from the cradle and press the AUTO /OFF
switch to the “AUTO ” (On) position. When you are finished using the flashlight
you may shut it off manually by pressing the AUTO /OFF switch to the “OFF
”
position. Or you may just return the flashlight to its cradle and it will shut off
automatically.
Remember that if the AUTO /OFF switch is left in the “OFF ” position the
flashlight will not turn on automatically when it is removed from the cradle and it
will not turn on automatically in the event of a power failure.
Notes:
• When fully charged the flashlight should provide up to ‘8 hours’ of continuous
operation before the battery is exhausted.
• When fully discharged the flashlight should be recharged in its cradle for
‘14-16 hours’ to return the battery to its fully charged condition.
• The battery is being charged whenever the flashlight is in the charging
cradle, regardless of the position of the AUTO /OFF switch.
27
CKS3095_041707.p65
27
17/4/2007, 16:06
Changing The Lithium Battery
Like all batteries, eventually the built in lithium battery will need to be replaced. A
number of factors, such as, the length of time between the date the radio was
manufactured and the date you plugged it in for the first time determine the amount
of time before replacement. During this initial storage period, the lithium battery is
supplying power to the SmartSet® computer memory. Once you plug the radio in,
your household outlet supplies the power, and the battery is not being used. A
fresh lithium battery can supply power to the SmartSet® computer for at least 3
years even if it is never connected to an AC power supply. If your clock radio was
connected to your AC supply within a few months after it was manufactured, and
you experience only the normal, nuisance type, short duration power interruptions,
your battery may last for up to 5 years or even longer.
When the battery power drops below a certain level, the
LOW indicator will
‘flash’. When you see this indicator, you should change the battery as soon as it is
convenient for you to do so. To change the battery proceed as follows:
1.) Purchase a replacement 3V lithium battery wherever batteries are sold. The
battery type is CR2430 or equivalent.
2.) Remove the battery from its package so it is ready to install.
IMPORTANT: Leave the radio AC power cord connected to your AC outlet.
This will provide power to the SmartSet® computer memory while the
original lithium battery is removed.
3.) Turn the radio face up and use a small screw driver to remove the screw
securing the battery holder to the cabinet.
BE CAREFUL NOT TO LOSE THIS SMALL SCREW!
28
CKS3095_041707.p65
28
17/4/2007, 16:06
4.) Remove the original battery from the holder and insert the new battery into the
holder the same way, observing the positive (+) direction. Slide the holder with
the new battery back into the slot in the cabinet.
5.) Replace the screw that secures the battery holder in the cabinet.
6.) Turn the radio right side up and confirm that the
LOW indicator is ‘Off’.
7.) Save these instructions. You’ll have to do this again five to eight years from
now!
29
CKS3095_041707.p65
29
17/4/2007, 16:06
Resetting The Clock After A Total Memory Loss
If you do not change the built in lithium battery within a reasonable period of time
after you see the
LOW warning indicator, the lithium battery may become
exhausted and will no longer be able to supply back up power to the SmartSet®
internal computer. If the unit is disconnected from the AC outlet after the battery is
exhausted, or if a power interruption occurs, the SmartSet® memory will be lost
and the clock will need to be reset when the power is restored. Be sure to install a
fresh lithium battery before you reset the clock, otherwise the clock will need to be
reset each time the power is interrupted.
If the lithium battery is exhausted and you experience an interruption in the AC
power supply, the clock will reset itself to its initial default setting when the power is
restored.
The initial default setting is “12:00 AM, Saturday, January 1st (1. 1), 2005”.
If you notice that the time on your SmartSet® clock radio is completely incorrect,
and the Day indicator is also wrong, press the MONTH/DATE button to see the
Date.
If the Date display is showing “1. 1” (January 1ST),
you probably experienced a total memory loss.
To reset the clock after a total memory loss, proceed as follows:
1.) Follow the instructions on page 28-29 and install a new CR2430 lithium battery
in the battery compartment.
2.) Connect the radio to your AC outlet and let the clock set itself.
3.) Depress the MONTH/DATE and TIME buttons together. The displaywill change
from ‘Time’ to ‘Year’.
While holding the MONTH/DATE and TIME buttons, press the SET + button
to set the display to the correct Year, then release the buttons.
30
CKS3095_041707.p65
30
17/4/2007, 16:06
4.) Depress the MONTH/DATE button. The display will change from ‘Time’ to
‘Month/Date’ (MM/DD).
While holding the MONTH/DATE button, press the SET + button to set the
display to the correct Month and Date. The Day indicator will change
automatically as you adjust the Month/Date settings. When the correct Month
and Date appear on the display, release the buttons.
5.) Depress the TIME button and the SET + button to set the display to the correct
Time. Be sure to confirm that you have set the time correctly to ‘AM’ or ‘PM’ by
observing the AM indicator.
6.) After you set the Time, reconfirm that the Day, and Month/Date displays are
still correct. Make final adjustments if necessary.
The SmartSet® clock memory is now reset and the new lithium battery will maintain
it for the next 5 to 8 years, depending on the number and duration of the power
outages you experience.
IMPORTANT NOTE:
After resetting the clock, don’t forget to reset your wake up times, and alarm
mode settings, and sleep timer settings as well.
Lithium Battery Precautions
• Dispose of the old battery properly. Do not leave it lying around where a young
child or pet could play with, or swallow it. If the battery is swallowed, contact a
physician immediately.
• Battery may explode if mistreated. Do not attempt to recharge it or disassemble
it. Do not dispose of the old battery in a fire.
31
CKS3095_041707.p65
31
17/4/2007, 16:06
CARE AND MAINTENANCE
Removal And Proper Disposal of Exhausted Batteries
Replacing the Rechargeable “AA” 1.2V 600mA Ni-Cd battery
1.) (a.) Insert the end of a straightened
b
paper-clip, toothpick, or similar
device into the small hole on the end
cap to depress the locking tab and
a
release the cap.
(b.) Remove the cap completely.
2.) Slide the exhausted battery out of the flashlight.
Caution:
Exhausted Ni-Cd battery must be disposed of properly.
Call 1-800-822-8837 for recycling information.
Do not dispose of battery in fire.
3.) Insert the fresh battery into the flashlight as shown.
4.) (a.) Turn the end cap until the arrow
mark on the end cap is aligned with
the arrow mark on the flashlight
body.
a
b
(b.) Replace the end cap by pushing
it on to the flashlight bodyuntil it locks
in place.
IMPORTANT: after installing a fresh battery the flashlight should be recharged
for 24 hours before initial use.
32
CKS3095_041707.p65
32
17/4/2007, 16:06
Notes:
The replacement Ni-Cd rechargeable battery is available from the Emerson
Customer Service Department.
Please call 1-800-898-9020 and specify that you need the replacement battery
for model number CKS3095 rechargeable flashlight.
The part number is “BATCKS3095”.
Caution: To ensure proper safety, only use the supplied or recommended
replacement battery.
Bulb Replacement
The flashlight in this unit use LEDs (Light Emitting Diodes) instead of
incandescent bulbs. These LEDs should last for the full useable life of
the product and they are not consumer replaceable.
There are no user serviceable parts inside this radio. Please refer all service
problems to a qualified service facility.
Care Of Cabinets
If the cabinet becomes dusty, wipe the exterior with a soft dust cloth only.
Never use dusting sprays or polishes on the cabinet.
If the cabinet becomes dirty or smudged with fingerprints it may be wiped with a
soft cloth that has been slightly dampened with a mild soap and water solution.
Always disconnect the power cord from the AC outlet before cleaning, and never
allow any liquid to get inside the cabinet.
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
R
CENTER PERMITTED TO PERFORM
WARRANTY...
SERVICE
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE,PLEASE WRITE TO:
Emerson Radio Corp.,
Consumer Affairs Dept.,
5101 Statesman Drive,
Irving, TX 75063.
33
CKS3095_041707.p65
33
17/4/2007, 16:06
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts at
an authorized Depot Repair Facility, or replace the product in our discretion. For
repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $9.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.,
5101 Statesman Drive,
Irving, TX 75063.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS, ANDYOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898M
The Serial Number of this unit is located on a label on the bottom of the cabinet.
Please take a moment now to write this Serial Number in the space provided below.
You may be asked for this number when calling for service assistance.
Model No: CKS3095B / CKS3095S
Serial No:
34
CKS3095_041707.p65
34
17/4/2007, 16:06
R
CKS3095-041707-02
Printed in China
CKS3095_041707.p65
35
17/4/2007, 16:06
|