Jura Capresso IMPRESSA S70 User Manual

IMPRESSA S70  
IMPRESSA X70  
Instructions for use  
07/2001  
Fig. 1  
Fig. 4  
Fig. 7  
Fig. 2  
Fig. 5  
Fig. 8  
Fig. 3  
Fig. 6  
Fig. 9  
A
B
12  
14 15  
16  
13  
D
C
B
A
E
F
17  
18  
19  
20  
11  
10  
9
8
G
H
7
21  
6
5
4
22  
3
2
1
Operating elements Jura Impressa S70/X70  
1 Drip tray / residual water container  
2 Drip tray cover  
3 Cover for programming keys  
4 Coffee key for 2 normal cups  
5 Coffee key for 1 normal cup  
6 Coffee key for 2 small cups  
7 Coffee key for 1 small cup  
8 Key for special coffee  
9 ON/OFF switch  
10 Rinsing key  
11 Display dialogue system  
12 Water tank with carrying handle  
13 Cover for bean container and aroma protection lid  
14 Cover for pre-ground coffee filler funnel  
15 Height-adjustable coffee-spout  
16 Cup warming tray  
17 Selector key for steam  
18 Selector key for hot water  
19 Selector switch for coffee or hot water/steam  
20 Pivoting nozzle for hot water/steam  
21 Frothing nozzle  
22 Container for coffee grounds  
Programming keys  
A
B
Change filter  
Back-setting of criteria / changing of memory indications  
downwards  
C
D
E
F
G
Open program  
Selector switch for pre-ground coffee  
Key for cleaning program  
Correction of program / close  
Forward-setting of criteria / changing of memory indicati-  
ons up-wards  
H
Key for decalcifying program  
12.5 Programming WATER HARDNESS.........page 13  
12.6 Programming ECONOMY MODE ............page 13  
12.7 Programming TIMER CLOCK ................page 13  
12.8 Programming automatic switch on time..page 13  
12.9 Programming automatic switch off time .page 14  
12.10 Cup counter .......................................page 14  
12.11 Programming language selection ...........page 14  
N
Table of contents  
Jura Impressa S70/X70  
1. Description .................................................page  
2. Safety instructions.......................................page  
2.1 Warnings ...........................................page  
2.2 Safety precautions ..............................page  
3. Check before use .........................................page  
3.1 Checking mains voltage........................page  
3.2 Checking fuse.....................................page  
3.3 Adding coffee beans ............................page  
3.4 Adjusting grinder ................................page  
4. Preparing machine .......................................page  
5. Rinsing the machine.....................................page  
6. Adjusting for water hardness.........................page  
7. Use of Claris filter cartridges ........................page  
7.1 Placing filter ......................................page  
7.2 Replacing of filter ...............................page 10  
8. Drawing off coffee .......................................page 10  
8.1 Drawing off powder coffee ...................page 10  
9. Drawing off hot water ..................................page 11  
10. Using steam................................................page 11  
11. Switching off machine..................................page 11  
12. Programming ..............................................page 12  
12.1 Programming POWDER QUANTITY........page 12  
12.2 Programming coffee temperature ..........page 12  
12.3 Programming water quantity.................page 12  
12.4 Programming FILTER ..........................page 13  
7
7
7
7
8
8
8
8
8
8
8
9
9
9
12.12 Program key  
..................................page 14  
13. Care and maintenance ..................................page 14  
13.1 Fill water ...........................................page 14  
13.2 Empty grounds container ....................page 14  
13.3 Empty drip tray .................................page 14  
13.4 Fill beans ..........................................page 15  
13.5 Removing foreign objects ....................page 15  
13.6 Clean machine ...................................page 15  
13.7 Unit calcified .....................................page 15  
13.8 Cleaning metal contacts ......................page 15  
13.9 General cleaning instructions ...............page 15  
13.10 Regular servicing ................................page 16  
14. Cleaning.....................................................page 16  
15. Decalcifying ................................................page 16  
15.1 Decalcifying coffee sector ....................page 16  
15.2 Decalcifying water sector .....................page 17  
16. Disposal......................................................page 17  
17. Tips for a perfect coffee ...............................page 17  
18. Messages....................................................page 18  
19. Problems ....................................................page 19  
20. Legal information.........................................page 20  
21. Technical specifications ................................page 20  
6
Important information for the user  
2. Safety instructions  
2.1 Warnings  
Thank you for choosing this Jura product.  
Children are unaware of the dangers that electrical machines  
represent. Therefore children should never be left unsupervised  
with electrical machines.  
Please study these instructions carefully before using your new  
machine and keep them in a safe place for easy reference in the  
future.  
This machine should only be used by people who have read and  
understood the operating instructions.  
Should you require further information or should particular pro-  
blems occur that are not dealt with in these operating instructions  
in sufficient detail for you, then please ask your local dealer for  
the information you require or contact Jura Elektroapparate AG  
directly.  
Never use a faulty machine or one with a damaged power cable.  
Never immerse the machine in water.  
2.2 Safety precautions  
Never expose the machine to the effects of rain, snow or frost  
and never operate it with wet hands.  
Place your machine on a solid level surface. Never leave it on a  
surface that is warm or hot (hob etc.). Choose a location that is  
inaccessible for children or pets.  
E
Remove plug from power socket if an absence for a longer  
period of time (holidays etc.) is planned.  
1. Description  
Always remove plug from power socket before cleaning.  
When removing plug from power socket, never tug on the cord  
or on the machine itself.  
This fully-automatic espresso/coffee machine impresses because of  
its user-friendly operational mode and its ingenious technology. In  
just one brewing-process it can prepare 1 or 2 cups of excellent,  
professional-quality espresso/coffee with guaranteed froth. Origi-  
nating from professional sectors and having been refined and fur-  
ther developed by Jura, the Intelligent Pre Brew Aroma System  
(I.P.B.A.S©) ensures full coffee aroma. The Impressa S70 enables  
you to adapt the resulting coffee to your personal taste due to the  
possibility of programming coffee-powder and water quantities as  
well as the brewing temperature.  
Never repair or open the machine yourself. All repairs should be  
performed by authorised service centres only using original Jura  
spare parts and accessories.  
The machine is connected to the mains power socket via an  
electric cable. Ensure that no-one trips over this cable and pulls  
down the machine. Keep children and animals at a distance to  
the machine.  
Never put the machine or even parts of it in the dishwasher.  
The machine works fully-automatically at the press of a key. A  
decoded text-display shows messages and simplifies the operation  
considerably. Because of the integrated rinsing, cleaning and  
decalcifiying programs care and maintenance is quick and easy.  
To prevent overheating place the machine in an airy place.  
7
If using acidic decalcifying agents be sure to immediately re-  
move any splashes and drops from delicate surfaces, especially  
natural stone and wooden surfaces, or take corresponding pre-  
cautions.  
You have the following possibilities:  
the smaller the dots, the finer the grinding  
the bigger the dots, the coarser the grinding  
The grinding grade should only be adjusted while the grinder  
is working.  
3. Check before use  
3.1 Checking mains voltage  
4. Preparing machine  
The machine is set for the correct voltage before leaving our  
factory. Ensure that your mains voltage corresponds to the details  
quoted on the rating plate attached to the bottom of the machine.  
Switch your machine on by pressing ON/OFF key  
chine adjusts fully-automatically to the starting position.  
. The ma-  
FILL WATER  
Remove water tank and rinse well with clear tap-water.  
3.2 Checking fuse  
Fill water tank and replace. Make sure that tank engages well.  
(Abb. ....).  
The machine is designed for a current of 10 amps. Check that an  
appropriate fuse is fitted.  
PLEASE WAIT  
RINSE UNIT  
3.3 Adding coffee beans  
Place a container under the coffee-spout (15) and press rinsing  
key  
Lift up cover of the bean container (13) and remove aroma pro-  
tection lid.  
.
UNIT RINSING  
Clean out any dirt or foreign object from the bean container.  
COFFEE READY  
Fill the grinder container with coffee beans, replace aroma pro-  
tection lid and close the cover.  
5. Rinsing the machine  
3.4 Adjusting grinder  
RINSE UNIT  
Place an empty cup under the coffee-spout (15).  
Press rinsing key  
You can adjust the grinder to the roast of your coffee. We recom-  
mend the following:  
.
for a light roast Ǟ a finer adjustment  
for a dark roast Ǟ a coarser adjustment  
If the machine has been switched off and has already cooled  
down it will be necessary to carry out this rinsing function  
when the machine is switched on again.  
After switching off the machine, the rinsing sets off automa-  
tically.  
Open the cover of the bean container (13).  
To adjust grinding turn selector switch (Fig. 1) to the desired  
position.  
8
6. Adjusting for water hardness  
PRESS KEY / POWDER QUANTITY  
+
Press key  
several times until the following message appears:  
The water is heated inside the machine. With use, this leads to  
calcium deposits (furring) forming on the machine. This will be  
automatically indicated on the display.  
For this reason, it is necessary to adjust the machine to the  
hardness of your local water before you use it for the first time.  
Use the enclosed test-sticks for this purpose.  
HARDNESS LEVEL 3  
P
By pressing key  
hardness level flashes  
you can hear an acoustic signal, the set  
+
You can alter the hardness level by pressing key - or . After  
setting, press key  
can be heard.  
P
once again to confirm. An acoustic signal  
1° water hardness on the German scale represents 1.79° on  
the French scale.  
N
Press key  
to return to stand-by-status.  
The machine has got 5 hardness settings to choose from. While  
adjusting the chosen grade is shown on the display.  
7. Use of Claris filter cartridges  
Under proper implementation of Claris filter cartridges,  
decalcifying of the machine becomes unnecessary. For  
further information, please read the brochure “Claris. Tough  
to calcium deposits, gentle to your coffee machine”.  
The symbols on the display mean:  
HARDNESS  
LEVEL – –  
water hardness function is switched off  
HARDNESS  
LEVEL 1  
German water hardness  
French water hardness  
1 – 7°  
1.79 – 12.53°  
7.1 Placing filter  
E
Pull up cartridge mounting. Pressing lightly, place the filter car-  
tridge in the water tank (Fig. 2).  
HARDNESS  
LEVEL 2  
German water hardness  
French water hardness  
8 – 15°  
14.32 – 26.85°  
Pull down cartridge mounting, until it engages audibly.  
HARDNESS  
LEVEL 3  
German water hardness  
French water hardness  
16 – 23°  
28.64 – 41.14°  
Fill water tank with cold, fresh tap-water and replace it.  
Switch the machine on by pressing key  
ON/OFF.  
HARDNESS  
LEVEL 4  
German water hardness  
French water hardness  
24 – 30°  
42.96 – 53.7°  
P
Open front cover (3) and press key  
until you hear an acoustic  
signal.  
The machine is adjusted to hardness level 3 before it leaves the  
factory. You can alter this setting by following the instructions  
below:  
PRESS KEY / POWDER QUANTITY  
+
Press key  
several times until the following message appears:  
FILTER NO  
Switch the machine on by pressing ON/OFF key  
. The  
P
By pressing key  
you can hear an acoustic signal.  
machine adjusts fully-automatically to the starting position.  
NO flashes  
PLEASE WAIT  
+
You can alter the setting by pressing key - or  
.
P
Open cover (3) and press key  
signal  
, until you hear an acoustic  
9
Place a sufficiently large container (approx. 1 litre) under the  
YES flashes  
pivoting nozzle (20). Turn selector switch for coffee or hot  
P
To confirm press key  
. An acoustic signal can be heard.  
water/steam (19) to position  
.
RINSE FILTER / OPEN TAP  
PLEASE WAIT / FILTER RINSING  
CLOSE TAP (the system gives off steam)  
COFFEE READY  
Place a sufficiently large container (approx. 1 litre) under the  
pivoting nozzle (20). Turn selector switch for coffee or hot wa-  
ter/steam (19) to position  
.
PLEASE WAIT / FILTER RINSING  
CLOSE TAP (the system gives off steam)  
FILTER YES  
The water might be slightly discoloured (this is not damaging  
to the health).  
N
Press key  
.
8. Drawing off coffee  
COFFEE READY  
Switch the machine on by pressing key ON/OFF  
.
PLEASE WAIT  
The water might be slightly discoloured (this is not dama-  
ging to the health).  
RINSE UNIT  
Put an empty cup under the coffee-spout (15) and press rinsing  
key  
.
7.2 Replacing of filter  
UNIT RINSING  
After drawing off 50 litres the filter loses its effect.  
COFFEE READY  
REPLACE FILTER  
Put 1, respectively 2 cups under the coffee-spout and press the  
required key. The pre-brew system (I.P.B.A.S©) moistens the  
coffee powder, briefly interrupts the flow and then starts the real  
brewing process.  
If only a little water is drawn off the filter should be changed every  
2 months. However no message will appear on the display. You  
will find a special turntable on the cartridge mounting to set the  
replacement date.  
Empty water tank and pull up cartridge mounting. Pressing light-  
ly, place the filter cartridge in the water tank (Fig. 2).  
You can interrupt the flow of coffee at any time by simply  
pressing any of the coffee keys.  
Pull down cartridge mounting, until it engages audibly.  
To obtain a perfect head of froth adjust the coffee-spout (15)  
to the size of your cups (Fig. 3).  
Fill water tank with cold, fresh tap-water and replace it.  
Switch the machine on by pressing key ON/OFF  
.
8.1 Drawing off powder coffee  
Open front cover (3) and press key , until you hear an acoustic  
signal.  
Open cover (3)  
RINSE FILTER / OPEN TAP  
Press selector key for pre-ground powder coffee  
.
10  
10. Using steam  
FILL POWDER  
Now put 1 or 2 level measuring spoons of pre-ground coffee into  
the pre-ground powder funnel (14).  
Steam can be used for heating up liquids as well as for frothing up  
milk for cappuccinos.  
To heat up liquids remember to push the frothing nozzle (21) up.  
For frothing up liquids push the frothing nozzle (21) down (Fig. 4).  
Put 1, respectively 2 cups under the coffee-spout and press the  
required key.  
Press selector key for steam  
lamp turns into a constant light.  
. Wait until the flashing of the  
Never use soluble instant coffee or quick coffee. Only use  
coffee powder from freshly ground beans or pre-ground va-  
cuum-packed coffee. Never fill the funnel with more than  
2 portions of coffee powder at a time. The powder funnel  
is not intended as a storage container.  
Put a cup under the pivoting nozzle (20).  
Immerse the frothing nozzle (21) into the milk you want to froth  
or into the liquid you want to heat up. Turn selector switch for  
coffee or hot water / steam (19) to the symbol  
If selector key  
is pressed by mistake this can be correc-  
.
ted by pressing one of the coffee keys.  
STEAM INTAKE  
To stop steam-function turn selector switch for coffee or hot wa-  
ter / steam (19) back to the symbol  
9. Drawing off hot water  
.
Press selector key for hot water . Wait until the flashing of the  
lamp turns into a constant light.  
After drawing off steam immediately draw off approx. 1dl of  
water and clean the outside of the nozzle with a cloth.  
E
Put a cup under the pivoting nozzle and turn selector switch for  
coffee or hot water / steam (19) to the symbol . The machine  
will now deliver hot water.  
If you want to draw off steam several times, the selector key  
for steam can be left on. The drawing off of steam is on  
stand-by-status. If you draw off steam only once, then the  
WATER SUPPLIED  
To stop this process turn selector switch for hot water / steam  
(19) back to the symbol . The cup should only be removed  
selector switch for steam  
the selector key anew.  
should be turned off by pressing  
When steam is first drawn off, there is a possibility of spat-  
tering. The pivoting nozzle becomes hot. Avoid direct  
contact with the skin.  
when the hot water has stopped its flow.  
The machine has a stand-by-status for hot water. If you want  
to alternate between drawing off coffee and hot water, the  
selector switch for hot water can be left turned on . If you  
draw off hot water only once, then the selector switch for hot  
water should be turned off by pressing the selector key  
anew.  
11. Switching off machine  
When the machine is switched off, the rinsing program is auto-  
matically run again. Therefore place an empty container under the  
coffee-spout (15) and press ON/OFF key  
. When the rinsing  
When hot water is first drawn off, there is a possibility of  
spattering. The pivoting nozzle becomes hot. Avoid direct  
contact with the skin.  
water has run into the container, the machine powers down.  
Discard the water.  
11  
12. Programming  
POWDER QUANTITY / SELECT KEY.  
+
You can go to the next setting by pressing key  
.
Before leaving our factory, the machine is adjusted to enable you  
to obtain coffee without any additional programming. In order to  
adapt the result to your personal taste, various settings can be pro-  
grammed individually. The programming keys are located behind  
the front cover (3).  
12.2 Programming coffee temperature  
TEMPERATURE COFFEE / SELECT KEY  
Now press the key that you want to programme.  
Select the required temperature (high or normal) by activating  
The following settings can be programmed:  
+
key  
or - .  
̈ Powder quantity  
̈ Brewing temperature  
̈ Water quantity  
To store the new coffee temperature in memory briefly press  
P
key  
.
̈ Filter  
TEMPERATURE COFFEE / SELECT KEY  
̈ Water hardness  
+
You can call up the next setting by pressing key  
.
̈ Economy mode  
̈ Timer clock  
12.3 Programming water quantity  
̈ Automatic switch on time  
̈ Automatic switch off time  
̈ Supplies and cup counter  
̈ Language selection  
WATER QUANTITY / SELECT KEY  
Put a cup under the coffee-spout (15) and then press the key that  
you want to programme.  
The selected value is confirmed  
12.1 Programming POWDER QUANTITY  
Now your machine prepares a coffee.  
Switch the machine on by pressing ON/OFF key  
.
P
ENOUGH COFFEE / PRESS KEY  
P
Press key  
until you can hear an acoustic signal.  
P
+
··········II··········  
OK?  
POWDER QUANTITY / SELECT KEY  
P
When the required water quantity is reached press key  
. You  
Now press the key that you want to programme. Use the key for  
1 cup only. The corresponding quantity for 2 cups is adjusted  
automatically by the machine after programming is finished.  
+
can call up the next setting by pressing key  
.
There is an additional possibility to alter the water quantity  
+
anew. Press key  
or - for this purpose.  
POWDER  
If you wish to draw another coffee to control the water quantity,  
+
··········II··········  
P
press key again otherwise press key  
quantity in memory.  
briefly to store water  
+
The powder quantity can be selected by pressing keys  
briefly.  
or -  
+
You can call up the next setting by pressing key  
.
To store the new powder quantity in memory briefly press  
P
key  
.
12  
12.4 Programming FILTER  
After 10 minutes the steam heating-system switches off  
automatically. The warning lamps go out. By pressing the  
steam key anew, you return to stand-by-status for drawing  
off steam.  
Please read chapter 7.1 “Placing filter”.  
12.5 Programming WATER HARDNESS  
(only with setting FILTER NO)  
ECONOMY MODE OFF means that the stand-by-status for  
steam is set to 10 minutes and the heating for the cup warm-  
ing tray is on. After 10 minutes the heating-system switches  
down to a stand-by temperature. By pressing the steam key  
anew, the machine returns to stand-by-status for drawing off  
steam.  
HARDNESS LEVEL 3  
P
Press key  
+
-
By pressing key  
hardness level.  
or  
briefly you can programme the water  
P
Then press key  
memory.  
briefly to store the water hardness level in  
12.7 Programming TIMER CLOCK  
A programming of the timer clock is necessary if an automa-  
tic switch on time is required.  
+
You can call up the next setting by pressing key  
.
TIME –.–  
To determine the water hardness level please read chapter 6.  
“Adjusting for water hardness”.  
P
Press key  
.
+
By briefly pressing key  
confirm by pressing key  
or - you can set the hours and then  
E
12.6 Programming ECONOMY MODE  
P
.
+
By briefly pressing key  
or - you can set the minutes and  
ECONOMY MODE OFF  
P
then confirm by pressing key  
.
P
Press key  
+
You can call up the next setting by pressing key  
.
ECONOMY (MODE OFF flashes)  
+
-
By briefly pressing key  
you would like.  
or  
you can programme the mode  
12.8 Programming automatic switch on time  
A programming of the timer clock is necessary if an auto-  
matic switch on is needed.  
P
Then press key  
briefly to store mode in memory  
+
You can call up the next setting by pressing key  
.
UNIT ON –.–  
You can programme your machine to “economy mode”. In  
the setting ECONOMY MODE ON the steam heating-  
system is switched off. The heating for the cup warming tray  
is switched off too. If you want to draw off steam you need  
P
Press key  
.
+
P
By briefly pressing key  
confirm by pressing key  
or - you can set the hours and then  
.
to press the steam key  
machine heats up.  
, warning lamps flash and your  
+
-
.
By briefly pressing key  
then confirm by pressing key  
or  
you can set the minutes and  
P
+
You can call up the next setting by pressing key  
.
13  
To switch off the automatic timer proceed as follows:  
COFFEE READY  
P
Press key  
N
Press key  
until you can hear an acoustic signal.  
N
Press key  
UNIT ON —:—  
If a mistake occurs while programming one of the above  
N
settings, just press key  
and the chosen setting moves back  
12.9 Programming automatic switch off time  
to its original standard setting.  
OFF AFTER 5.0 HOURS  
13. Care and maintenance  
13.1 Fill water  
P
Press key  
+
P
-
By briefly pressing key  
or  
you can set the hours and then  
confirm by pressing key  
(0.5 to 9.0 hours).  
FILL WATER  
+
You can call up the next setting by pressing key  
.
If this message shows on the display no more coffee can be  
drawn off. Top up water.  
12.10 Cup counter  
The water tank should be rinsed and filled with fresh water  
daily. Only use fresh, cold water. Never top up with milk,  
mineral water or any other liquids. You can top up water  
without removing tank.  
200 SUPPLIED (TOTAL SUPPLIED)  
To obtain the information press the required key. The display  
will show you the number of times the function has been chosen.  
+
You can call up the next setting by pressing key  
.
13.2 Empty grounds container  
It is not possible to call up hot water and steam supplies.  
Coffee grounds are collected in the grounds container.  
EMPTY GROUNDS  
12.11 Programming language selection  
If this message shows on the display no more coffee can be  
drawn off. It is necessary to empty the grounds container.  
P
Press key  
Remove drip tray carefully as there is water in it.  
+
-
By briefly pressing key  
and then confirm by pressing key  
or  
call up the language desired  
P
.
Do not disconnect the machine from power socket while  
you empty grounds.  
N
By pressing key  
you can leave the programming modus or  
+
you can call up the next setting by pressing key  
.
13.3 Empty drip tray  
N
12.12 Program key  
EMPTY TRAY  
N
By using key  
you can set back the following settings (powder  
If this message shows on the display no more coffee can be  
quantity, coffee temperature, water quantity) to their original stan-  
dard settings.  
drawn off. It is necessary to empty the drip tray.  
Remove drip tray carefully as there is water in it.  
14  
13.4 Fill beans  
13.7 Unit calcified  
FILL BEANS  
UNIT CALCED  
Fill in beans as described in chapter 3.3.  
The machine signals when decalcifying becomes necessary.  
The message FILL BEANS will only disappear after drawing  
off a coffee. We recommend cleaning the bean container  
from time to time with a dry cloth before you refill beans.  
Switch off the machine for this purpose.  
Under the correct implementation of Claris filter cartridges,  
decalcifying of the machine becomes unnecessary. For fur-  
ther indications read Chapter 7 “Use of Claris filter cartrid-  
ges”.  
13.5 Removing foreign objects  
13.8 Cleaning metal contacts  
Switch off your machine by pressing ON/OFF  
key.  
EMPTY TRAY  
Remove plug from power socket.  
To switch off this message you need to remove calcified deposits  
from the metal contacts. Proceed as follows:  
Open bean container (13) and remove the beans. The remaining  
beans can be removed with a vacuum cleaner.  
Rinse fastenings in groove (B) (Fig. 8) as well as the metal con-  
tacts (A) with hot water and some washing-up liquid. Then clean  
the fastenings in groove (B) as well as metal contacts with a  
brush.  
Loosen both screws in the bean container and then remove con-  
tainer (Fig. 5+6)  
Remove any remaining beans with a vacuum cleaner.  
Put the spanner on (Fig. 7).  
E
Now turn spanner anticlockwise until the foreign object loosens.  
Remove remaining powder with a vacuum cleaner.  
Replace bean container and fasten screws.  
13.9 General cleaning instructions  
Never use abrasive articles or corrosive chemicals to clean your  
machine.  
Wipe down the casing inside and out using a soft damp cloth.  
13.6  
Clean machine  
Clean the pivoting hot water / steam nozzle after every use.  
CLEAN UNIT  
After warming milk, draw off some hot water to clean the pivo-  
ting nozzle inside.  
After coffee, etc., has been drawn off 220 times or after 180 rinsing  
programs have been run, the machine must be cleaned. You can  
continue to draw off coffee and hot water / steam. However we re-  
commend that you clean the machine (as described in chapter 14)  
within the next few days.  
You can take off the pivoting nozzle for a thorough cleaning  
The water tank should be rinsed and filled with clean water  
daily.  
CLEAN NOW  
If you notice any furring in the water tank, this can be  
decalcified separately with a customary decalcifying agent.  
Remove the tank from the machine for this purpose.  
An acoustic signal indicates the need of an immediate cleaning.  
15  
15. Decalcifying  
If a Claris filter cartridge is used, remove it beforehand.  
Your machine has an integrated decalcifying program (duration  
approx. 35 min.).  
Please use Jura decalcifying tablets only. These are available from  
your Jura dealer.  
13.10 Regular servicing  
Regular Jura services ensure your machine’s reliability and longer  
life. Keep the original packaging to protect the machine while  
being transported.  
Run the decalcifying program only after the machine has  
been switched off for at least 5 hours and has cooled down  
completely. The running decalcifying program must not be  
interrupted.  
14. Cleaning  
The machine has an integrated cleaning program. The procedure  
lasts about 15 minutes. Please use Jura cleaning tablets only. These  
are available from your Jura dealer.  
If using acidic decalcifying agents be sure to immediately  
remove any splashes and drops from delicate surfaces,  
especially natural stone and wooden surfaces, or take cor-  
responding precautions.  
It is essential not to interrupt the process once it has been started.  
In any case please wait until the filled decalcifying agent is  
used up and the tank is empty. Never top up the decalcifying  
agent.  
Switch on machine by pressing  
key.  
Press key  
until you can hear an acoustic signal.  
EMPTY TRAY (FILL WATER might show as well)  
Put a sufficiently large container under the coffee-spout (15)  
in order to prevent cleaning liquid from running into the drip  
tray.  
15.1 Decalcifying coffee sector  
Remove and empty water tank.  
Replace empty water tank.  
ADD TABLET (Fig. 9) / PRESS CLEANING  
UNIT CLEANING  
Switch off your machine by pressing ON/OFF  
Open cover (3).  
key.  
EMPTY TRAY  
Press key until you can hear an acoustic signal.  
RINSE UNIT  
EMPTY TRAY  
COFFEE READY  
AGENT IN TANK  
Pour 0.6 litres of water into a container and completely  
dissolve the contents of a blister pack (2 tablets). Then fill  
the mixture into the water tank.  
The powder funnel for pre-ground coffee should be cleaned  
after each cleaning process. Remove it from the machine ,  
rinse it with hot tap water and replace it after drying.  
CHOOSE SECTOR / AGENT IN TANK /  
PRESS CALC  
Turn selector switch for coffee to the symbol  
Press key  
.
.
16  
COFFEE SECTOR / UNIT DECALCIFYING  
AGENT IN TANK / CHOOSE SECTOR /  
PRESS CALC  
Inside the machine the decalcifying agent is conducted to the  
drip tray.  
Place a container under the pivoting nozzle and turn selector  
switch for coffee or hot water/steam (19) to the symbol  
.
EMPTY TRAY  
Press key  
.
FILL WATER  
UNIT DECALCIFIYING / WATER SECTOR  
PRESS CALC  
FILL WATER  
COFFEE SECTOR / UNIT DECALCIFIYING  
Rinse water tank well and top it up with fresh tap water.  
Inside the machine the water is conducted to the drip tray.  
PRESS CALC  
EMPTY TRAY / CLEAN CONTACTS  
(please refer to chapter 13.8)  
WATER SECTOR / UNIT DECALCIFYING  
CLOSE TAP  
PLEASE WAIT  
RINSE UNIT  
RINSE UNIT  
UNIT RINSING  
Place a container under the coffee-spout (15) and press rinsing  
key  
.
COFFEE READY  
UNIT RINSING  
16. Disposal  
COFFEE READY  
E
For correct disposal, you should return your coffee machine to your  
dealer, Jura service centre or Jura Elektroapparate AG.  
15.2 Decalcifying water sector  
This message will only appear if the unit is ready to draw off water  
or steam.  
17. Tips for a perfect coffee  
Remove and empty water tank.  
Height adjustable coffee-spout  
You can adjust the height of the coffee-spout to your cup sizes.  
Replace empty water tank.  
Grinding  
Switch off your machine by pressing ON / OFF  
Open cover (3).  
key.  
Please refer to chapter 3.4 “Adjusting grinder”.  
Pre-warm cups  
Press key until you can hear an acoustic signal.  
You should warm cups in advance with hot water or steam. The  
smaller the quantity of coffee, the more important warming the  
cups is.  
EMPTY TRAY  
AGENT IN TANK  
Pour 0.6 litres of water into a container and completely dis-  
solve the contents of a blister pack (2 tablets). Then fill the  
mixture into the water tank.  
Sugar and cream  
Warmth is lost by stirring the contents of the cup. Adding milk or  
cream from the refrigerator considerably lowers the temperature of  
the coffee.  
17  
18. Messages  
Cause  
Action  
FILL WATER  
Water tank is empty  
Top up with water  
Water level indicator in tank is jammed  
Tank is calcified, water level indicator is stuck  
Empty tank, rinse out, fill up and replace  
Remove tank, decalcify, rinse well, fill up with  
water and replace  
FILL BEANS  
Bean container is empty  
Top up with beans  
Message still displayed, although beans filled  
Draw off cup of coffee. FILL BEANS message  
only disappears after coffee is drawn off  
A foreign object is stuck in the grinder  
Coffee grounds container is full  
Remove foreign object as described in chapter  
13.5 “Removing foreign objects”  
EMPTY GROUNDS  
Remove drip tray, empty grounds container,  
replace tray  
Message still displayed, although grounds  
container emptied.  
The tray was out of the machine for less than  
8 sec for emptying. Take tray out again for  
approx. 10 sec and replace  
The message appears after only a few cups  
have been drawn off  
Leave the machine switched on while  
the grounds container is being emptied. The  
counter is only reset to zero if the machine is left  
switched on  
TRAY MISSING  
EMPTY TRAY  
Tray has not been replaced correctly  
Insert tray correctly  
Grounds have fallen under tray and are preventing  
it from being correctly inserted  
Remove tray, clean inside  
of machine, replace tray  
The residual water container is full  
Remove container carefully, empty, rinse out  
and replace  
Message still displayed, although container emptied  
Remove container, clean metal contacts  
(please refer to chapter 13.8)  
18  
Cause  
Action  
CLEAN UNIT  
You have drawn off coffee 220 times or run  
the rinsing program 180 times  
Clean as described in chapter 14  
Message still displayed, although machine cleaned  
Run cleaning program again; this time do  
not add cleaning tablet  
UNIT CALCED  
COFFEE SECTOR  
WATER SECTOR  
The appropriate sector needs decalcifying  
Run decalcifying program as described  
in chapter 15  
Message still displayed, although machine decalcified  
Run cleaning program again; this time using  
water only and without decalcifying agent  
CLOSE TAP  
FAULT  
Not ready to provide water or steam  
Various causes  
Switch over to coffee sector, press water or  
steam key and then draw off the water or steam  
required  
Ring the hotline  
E
19. Problems  
Problem  
Cause  
Action  
Coffee only flows in dribs  
and drabs while drawing off  
– Powder too fine  
– Adjust grinder to a coarser grinding  
– Run one or two rinse programs  
If result is no better, clean the machine  
as per instruction  
Coffee flow is stopped  
after pre-brewing  
– Not enough coffee powder in the system  
– Foreign element in grinder  
– Draw off one cup of coffee  
Grinder is extremely noisy  
– Proceed as described in chapter 13.5  
19  
Problem  
Cause  
Action  
Not enough froth while  
frothing up milk  
– Unsuitable milk-type  
– Use full cream milk  
– Clean frothing nozzle  
– Draw off steam  
– Frothing nozzle blocked  
– Frothing nozzle in wrong position  
If the above mentioned problems and/or messages still persist, please contact your dealer  
or get in touch directly with Jura Elektroapparate AG.  
20. Legal information  
21. Technical specifications  
These operating instructions contain all the information necessary  
for the correct use, operation and maintenance of your espresso/  
coffee machine.  
Understanding and complying with the directions contained in  
these operating instructions are essential to ensure that the machine  
is utilised without risk and to ensure safety during operation and  
maintenance.  
These operating instructions cannot cover all the possible ways in  
which this machine may be used. This machine has been designed  
for private use in households.  
We would like to further point out that the contents of these opera-  
ting instructions in no way constitute a part of, or alter, any pre-  
vious or existing contract, agreement or legal relationship. All ob-  
ligations on the part of Jura Elektroapparate AG result solely from  
the relevant sales agreement which also contains full details of the  
only warranty terms valid in respect of this machine. The contrac-  
tual terms of this warranty are neither extended nor limited in any  
form by the information in these operating instructions.  
These operating instructions contain information that is protected  
by copyright. The photocopying or translation into any other lan-  
guage of these instructions without prior written authorisation from  
Jura Elektroapparate AG is strictly prohibited.  
Impressa S70  
Voltage:  
Power consumption:  
Fuse:  
230 V AC  
1350 W  
10 A  
Safety measures exam:  
Energy consumption standby:  
Energy consumption ready to make  
coffee:  
approx. 4,4  
approx. 31 Wh, Economy Mode on  
approx. 41 Wh, Economy Mode off  
max. 15 bar  
2,7 litres  
280 gr.  
max. 16 port.  
approx. 1,1 m  
11,7 kg  
34,5 x 35 x 39 cm  
Pump pressure:  
Water tank:  
Capacity, bean container:  
Capacity, grounds container:  
Cable length:  
Weight:  
Dimensions (BxHxD):  
Impressa X70  
Water tank:  
Capacity, grounds container:  
Weight:  
5,7 litres  
max. 40 port.  
15 kg  
Dimensions (BxHxD):  
41 x 47 x 39 cm  
20  

Motorola MOTORAZR V3 User Manual
Kenwood KDC 129S User Manual
JVC KD R35 User Manual
Huawei Technologies Cell Phone C8800 User Manual
HTC TOUCH PRO 2 User Manual
HTC MOZART 7 User Manual
Hitachi Deskstar HDS721032DLE630 User Manual
Blackberry PGP User Manual
Asus M307 User Manual
Antec Quiet Computing 3U22EPS600 User Manual