Denon PMD340 User Manual

Model PMD330/PMD331/PMD340 UserGuide

Compact Disc Player

INPORTANT SAFETY

INSTRUCTIONS

READ BEFORE OPERATING EQUIPMENT

This product was designed and manufactured to meet strict

12. Grounding or Polarization — The precautions that should be

taken so that the grounding or polarization means of an

appliance is not defeated.

quality and safety standards. There are, however, some installa-

tion and operation precautions which you should be particularly

aware of.

1. Read Instructions — All the safety and operating instruc-

tions should be read before the appliance is operated.

2. Retain Instructions — The safety and operating instructions

should be retained for future reference.

AC POLARIZED PLUG

3. Heed Warnings — All warnings on the appliance and in the

operating instructions should be adhered to.

13. Power-Cord Protection — Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular at-

tention to cords at plugs, convenience receptacles, and the

point where they exit from the appliance.

4. Follow Instructions — All operating and use instructions

should be followed.

5. Water and Moisture — The appliance should not be used

near water — for example, near a bathtub, wash-bowl,

kitchen sink, laundry tub, in a wet basement, or near a

swimming pool, etc.

14. Cleaning — The appliance should be cleaned only as recom-

mended by the manufacturer.

15. Nonuse Periods — The power cord of the appliance should

be unplugged from the outlet when left unused for a long pe-

riod of time.

6. Carts and Stands — The appliance should be used only

with a cart or stand that is recommended by the manufac-

turer.

16. Object and Liquid Entry — Care should be taken so that

objects do not fall and liquids are not spilled into the enclo-

sure through openings.

7. An appliance and cart combination should be moved with

care. Quick stops, excessive force, and uneven surfaces

may cause the appliance and cart combination to overturn.

17. Damage Requiring Service — The appliance should be

serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged; or

B. Objects have fallen, or liquid has spilled into the appli-

ance; or

C. The appliance has been exposed to rain; or

D. The appliance does not appear to operate normally or ex-

hibits a marked change in performance; or

8. Wall or Ceiling Mounting — The appliance should be

mounted to a wall or ceiling only as recommended by the

manufacturer.

E. The appliance has been dropped, or the enclosure dam-

aged.

18. Servicing — The user should not attempt to service the

appliance beyond that described in the operating instruc-

tions. All other servicing should be referred to qualified ser-

vice personnel.

9. Ventilation — The appliance should be situated so that its

location or position does not interfere with its proper ventila-

tion. For example, the appliance should not be situated on a

bed, sofa, rug, or similar surface that may block the ventila-

tion openings; or, placed in a built-in installation, such as a

bookcase or cabinet that may impede the flow of air through

the ventilation openings.

10. Heat — The appliance should be situated away from heat

sources such as radiators, heat registers, stoves, or other

appliances (including amplifiers) that produce heat.

11. Power Sources — The appliance should be connected to a

power supply only of the type described in the operating

instructions or as marked on the appliance.

CONTENTS

Features ......................................................................................................................................................................... 1

CD-TEXT ........................................................................................................................................................................ 1

CD-RW Disc Playback................................................................................................................................................... 1

Preparation .................................................................................................................................................................... 2

Name and Operation of Each Part .............................................................................................................................. 3

Playing a CD .................................................................................................................................................................. 7

Using the Pitch Controls .............................................................................................................................................. 9

Using the A-B Repeat Function................................................................................................................................. 10

Playback Using the Program Function ..................................................................................................................... 11

Playback Using the CUE Function ............................................................................................................................ 12

Playback Modes .......................................................................................................................................................... 14

Synchro Recording ..................................................................................................................................................... 15

Using a Remote Control (Not Included) ................................................................................................................... 15

CD-TEXT Information Display.................................................................................................................................... 16

Using the Preset Menu ............................................................................................................................................... 17

Using the Control Port (PMD331/PMD340 Only) ...................................................................................................... 18

Fader Start ................................................................................................................................................................... 19

Troubleshooting .......................................................................................................................................................... 19

Specifications.............................................................................................................................................................. ⁄

Figures ......................................................................................................................................................................... ¤

Connection .................................................................................................................................................................. ‹

External Dimensions .................................................................................................................................................. ‹

After you unpack the CD player, make sure that all of the following accessories are included:

- This guide

- Power cord

- Stereo audio cable with RCA pins

Features

- Supports CD-TEXT

- Equipped with the latest Philips pickup mechanisms

Model PMD330 (high-performance mechanism)

Model PMD331 (high-performance mechanism)

Model PMD340 (high-performance, high-durability mechanism)

- Can be installed in standard 19-inch rack (2U)

- Shockproof (PMD331/PMD340) 10 seconds

- Supports instant start (PMD331/PMD340)

CD TEXT

Look for these symbols on CDs that

support CD-TEXT.

- Supports playback of CD-RW (rewritable) discs

- Supports synchronized operation with other Marantz components

that support RC5 codes.

- Pitch bend control +/– 8% (PMD331/PMD340)

- Pitch control +/–12% max., 0.1% steps

CD-TEXT

A CD-TEXT disc is a new type of music CD that includes, in addition to the music found on a conventional CD, text data containing

the artist’s name, the album name, track names, etc. This text data is recorded in an area that was unused on music CDs.

Accordingly, a CD-TEXT disc can be played on any conventional CD player, but the text data can be viewed only if the disc is played

on a player that supports the CD-TEXT function, such as the PMD330/331/340.

The player determines automatically whether the current disc is a conventional CD or a CD-TEXT disc.

This player can display the album name, track name, the artist’s name, the songwriter’s name, the composer’s name, and the

arranger’s name, as long as that information is recorded on the disc. Not all of this information will be present on every disc.

For details on how CD-TEXT is displayed, refer to the description of operation found later in this guide.

- This player can display 12 characters of text at one time. If the text data is longer than 12 characters, the text will scroll across the

display from right to left.

- Some CD-TEXT discs include the called “highlights”. This CD player does not support the Highlight Scan function to play the

highlights in sequence.

- The following languages can be displayed as CD-TEXT: English, French, Spanish, and German.

CD-RW Disc Playback

In addition to conventional music CDs and CD-R discs, this CD player can also play CD-RW discs.

- In order to play a CD-R or CD-RW disc, the TOC* must be recorded properly.

The process of writing the TOC information to the disc is called “finalizing,” and if this task was not completed properly, the disc

cannot be played back because it will not be recognized properly as a music CD by a regular CD player.

For details, refer to the instruction manual provided with the CD recorder.

- This CD player can only play discs that were recorded in the CD-DA format. Never attempt to “play” a CD-ROM or similar disc

containing computer data.

- When playing a CD-RW disc, it sometimes takes longer to read the TOC compared with a music CD or a CD-R disc.

- This CD player may not be able to play some CD-RW discs properly, depending on the conditions under which the disc was

recorded.

* “TOC” stands for “Table of Contents,” and contains information such as the number of tracks on a disc and the total playback time.

Preparation

Introduction

Compact Discs

Thank you for purchasing the Marantz PMD330/PMD331/

- Handle discs carefully and do not damage or scratch the data side.

- To protect the disc, avoid placing it in the following locations:

• in direct sunlight or near a source of heat.

• in a damp or dirty place.

PMD340 Compact Disc Player.

Please read these operating instructions carefully. We recom-

mend you read the entire user guide before you attempt to

connect or operate this player.

• in a place which could be exposed to rain or near a window.

- Keep the disc surface clean.

The callout numbers indicated on the drawing in the end of

this manual correspond to the same numbers in the text.

• When cleaning the disc surface, use compact disc cleaner

and wipe as shown below.

Precautions

The following precautions should be taken when operating the

equipment.

Wipe in a radial

direction.

Do not wipe in circum-

ferential direction.

General precautions

- When installing the equipment, ensure the following points:

• do not expose to excessive heat, cold, moisture or dust.

• do not expose to direct sunlight.

• do not use conventional record cleaner.

• store discs properly by placing them in the disc cases.

• do not expose to electrostatic discharges.

• never place heavy objects on the equipment.

do not pull out the AC cord by pulling on the cord; grasp

the plug.

- Contact the nearest dealer or customer service if problems

occur.

Before Turning Off the Power

- Make sure to close the disc tray by pressing the OPEN/

CLOSE button before turning off the power.

Cautions of Installation

WARNING

- Install the player horizontally (or within 10 degrees of level).

Too much inclination may result in damage to the player.

- Secure the player at four parts when installing it in a 19-inch

rack. (See also Figure 3)

•Do not use force to open or close the disc tray during power

off. Force may result in damage to the tray.

•Place nothing but a compact disc in the tray. Inserting objects

other than discs in the tray may result in damage to the tray.

10°10°

OFF

ON/

PIT

A-B

END

PITC

INDE

PLA

10°

TIME

TEX

LEVE

PHON

HEAD

MAX

OFF

TCH

PIT

POW

A-

-B

PIT

NDE

SEA

AST

RESE

RES

YER

MIN

Press the

close the disc tray before

turning the power off.

button to

Do not turn off the power

while the disc tray is

open.

Name and Operation of Each Part *

- If this CD player is to be connected to equipment that is

zANALOG OUTPUT

equipped with a RC5 remote control jack, be certain to connect

the “REMOTE CONTROL IN” jack on this unit with the

“REMOTE CONTROL OUT” jack on the other unit.

- When this CD player is connected to a cassette recorder or a

disc recorder (CD-R, CD-RW, etc.), RC5 provides synchro re

cording capabilities. (See also page 15.)

(Analog output jacks)

These are the analog signal output jacks. The red jack is the

right channel audio output, and the white jack is the left chan-

nel audio output jack.

Caution

Do not connect these jacks to the PHONO jacks on an ampli-

fier.

nANALOG BALANCED OUTPUT LEVEL

(Analog balanced output level adjustment)

xDIGITAL OUTPUT (SPDIF)

(PMD331/PMD340 only)

(Digital output jack)

Use a Phillips type screwdriver to adjust the analog balanced

output level. Turn the screwdriver clockwise to increase the

output level, and turn the screwdriver counterclockwise to de-

crease the output level. (Min. level = -11 dBu)

The digital signal from the compact disc that is being played is

output through this jack.

Connect a device with a digital input jack (such as recording

equipment, an amp, or a D/A converter) to this jack through a

RCA cable.

Caution

-Do not use excessive force when turning the screwdriver.

-The output level and channel balance are adjusted when the

unit is shipped from the factory. Do not change these adjust-

ments inadvertently.

Note:

When outputting a digital signal from the PMD331/PMD340,

set “D.OUT” in the Preset menu to “On”.

For details on how to make this setting.

(See also page 17.)

mANALOG BALANCED OUTPUT

(Analog balanced output jacks)

cFADER START

(PMD331/PMD340 only)

(Fader start input jack)

Connect a device with analog balanced inputs to these jacks

through a cable with XLR connectors.

An external switch connected to this jack can be used to con-

trol disc pause and playback.

Note:

(See also page 19.)

When connecting another device to this CD player through

these jacks, confirm that the pin assignments of the XLR con-

nectors match before making the connection.

If the pin assignments are different, change the connections

in the XLR connector cable so that the pin assignments match.

On the PMD331/PMD340, this feature is in the CONTROL I/O

connector ⁄0.

(See also page18.)

vREMOTE INT/EXT

(RC5 remote control internal/external switch)

When using an infrared remote control transmitter to control

this CD player, set this switch to “INT”. When incorporating this

CD player into a system by connecting this CD player (for re-

mote control) to equipment that is equipped with a RC5 com-

patible output, set this switch to “EXT”.

XLR Connector Pin Assignments for this CD Player

1 GND

2 HOT(+)

3 COLD(-)

, DIGITAL OUTPUT (SPDIF)

(Digital balanced output jack)

Note:

Please set to “EXT” when you are using this CD player with-

out a remote control. The CD player will then not be able to

receive signals from another infrared remote control transmit-

ter.

(PMD331/PMD340 only)

Connect a device with a digital balanced input to this jack through

a cable with XLR connectors.

Note:

The digital format output on this balanced connectors is SPDIF.

Most products that contain an XLR digital input are designed

to accept an AES/EBU format signal. Be aware that the AES/

EBU input on some products will not accept SPDIF, even

though the audio data is identical.

bREMOTE RC5 IN/OUT

(RC5 remote control input/output jack)

This CD player can be controlled remotely by connecting this

CD player via a remote control cable to other equipment that

support RC5.

* Refer to the figures on the pages at the back of this user’s guide. The callout numbers on the figures correspond to those found in

the text.

Name and Operation of Each Part

. DIGITAL OUTPUT (SPDIF)

uTIME (Time display)

(Optical digital output jack)

Press this button to cycle the display D through the following

displays: track remaining time → track elapsed time → disc

remaining time → disc elapsed time → total disc playing time →

back to “track remaining time”, etc.

(PMD331/PMD340 only)

The digital signal from the compact disc that is being played is

output through this jack.

Connect a device with an optical digital input jack (such as

recording equipment, an amp, or a D/A converter) to this jack

through an optical cable.

iTEXT (CD text display)

Press this button while a CD-TEXT disc is in the CD player to

switch the character displayEfrom a time indicator display to

a text display.

Notes:

-Be careful not to bend the optical fiber cable.

-Be sure to attach the connector caps when the OPTICAL

connectors are not used.

Subsequent presses of this button will toggle through the avail-

able CD-TEXT displays.

(See also page 16.)

⁄CONTROL I/O

o0 to 9 (Numeric buttons)

(Control I/O jack)

These buttons are used to select tracks. When registering

tracks for programmed playback, use these buttons to specify

the tracks.

(PMD331/PMD340 only)

This is the remote control input/output connector.

(See also page 18.)

PRESET

⁄

POWER CONNECTOR

Connect the power cord to this connector and connect the other

end of the power cord to an AC outlet.

Press this button to put the player in Preset Setting mode.

(See also page 17.)

PROG (Program)

Press this button to put the player in Program Registration mode.

qPOWER (Power button)

(See also page 11.)

Press this button once to turn the power on; press it again to

turn the power off.

wDISC TRAY

This is the disc tray on which the CD is placed.

Press the button yto open and close the disc tray.

eHEADPHONE (Headphone output jack)

Plug headphones into this jack.

The headphone volume level can be adjusted by using the

headphone level r control.

rLEVEL (Headphone volume level adjustment)

This knob is used to adjust the headphone volume level.

tLCD Display

This displays the playing time, various playback modes, etc.

(Disc tray open/close)

Press this button to open the disc tray w.

Place a compact disc on the tray with the label facing up, and

then press this button again to close the tray.

Name and Operation of Each Part

(Track skip back)

CONTRAST (LCD contrast)

Press this button while a CD is playing to send the player back

to the beginning of the current track. Pressing this button more

than once sends the player back that many tracks.

This is used to adjust the LCD displaytcontrast. Turning this

control clockwise using a small screwdriver causes the dis-

play contrast to become stronger; turning this control counter-

clockwise causes the display to become fainter.

/ EXIT (Stop/Exit)

Caution

- This button has two functions: STOP and EXIT.

- Press this button to stop a CD that is currently playing.

- In Play Mode/Preset setting or Program entry mode, press

this button to return to the normal mode.

Do not use excessive force when turning the screwdriver.

PITCH/SEARCH (Pitch/Search dial)

(PMD331/PMD340 only)

- Press this button twice to clear a set CUE point.

While playing

Turn this dial in the clockwise direction to increase the pitch

speed; turning this dial in the counterclockwise direction de-

creases the pitch speed. (maximum: +/–12%)

The position of the pitch control is indicated on the LCD dis-

play F.

(Track skip forward)

Press this button while a CD is playing to send the player ahead

to the beginnig of the next track. Pressing this button more

than once sends the player ahead that many tracks.

While paused

To conduct a frame search in the forward direction, turn this

dial clockwise; to conduct a frame search in the reverse

direction, turn this dial counterclockwise.

CUE/CLEAR

This button has two functions: CUE and CLEAR.

- Press this button to perform the cue operation.

(See also page 12.)

INDEX –

- In program entry mode, press this button to clear a programmed

track.

Press this button to search for the previous index.

Each time the INDEX – button is pressed, the INDEX number

that is displayed decreases by “1”.

- In Play Mode/Preset setting mode, press this button to cancel

a change that has not been confirmed.

(Fast reverse)

MODE

When playing a CD, press this button to scan backwards quickly

Press this button to change or check the playback mode.

through the current track.

(See also page 14.)

(Play/pause), ENTER

END

This button has three functions: PLAY, PAUSE, and ENTER.

- If playback is paused or when performing a search, press

this button to begin playing the CD.

- Press this button while playback is paused to monitor the end

of the track. The monitor time can be set between 5 to 35

seconds through the Preset menu.

- If the CD is stopped, pressing this button causes the CD

player to search for the first track and begin playing.

- If the CD is playing, pressing this button pauses playback.

(See also page 17.)

- The END button lights while the End Monitor operation is in

progress.

While a CD is paused, the

button flashes.

- In Play Mode/Preset setting or Program entry mode, press

INDEX +

this button to save a change.

Press this button to search for the next index.

Each time the INDEX + button is pressed, the INDEX number

that is displayed increases by “1”.

(Fast forward)

When playing a CD, press this button to scan forwards quickly

through the current track.

Name and Operation of Each Part

A - B

Display

This button is used to specify a start point A and an end point

B for repeated playback between the two points.

(See also page 10.)

PITCH ON/OFF

- Press this button again to return the PITCH speed to the

value indicated on the LCD display F.

- Press this button while the PITCH speed has been changed

to return the playback speed to 0 % (no change).

(See also page 10.)

A TRACK

Displays the disc track number.

B INDEX

PITCH + (PMD330 only)

Displays the disc index number.

Press this button to increase the CD PITCH speed.

(maximum: +12%)

C Operation display

Displays the play mode that is set.

PITCH - (PMD330 only)

Press this button to decrease the CD PITCH speed.

D Playing time display

(maximum: –12%)

Displays the position on the disc currently being played, with

“M” representing minutes, “S” representing seconds, and “F”

representing frames.

PITCH BEND + (PMD331/PMD340 only)

Press this button to temporarily increase the PITCH speed of

Note:

the CD that is currently being played back.

(+8%)

There are 75 frames in each second.

(See also page 10.)

E Character display

PITCH BEND - (PMD331/PMD340 only)

- Displays messages when performing a preset operation or a

programming operation.

Press this button to temporarily decrease the PITCH speed of

the CD that is currently being played back.

( – 8%)

- The 10-segment bar indicates the track playing position.

- Displays CD-TEXT information.

(See also page 10.)

- Also displays other various messages.

IR (Infrared remote sensor)

F PITCH display

This sensor picks up signals from a RC5 based infrared re-

Displays the PITCH speed numerically with a precision of 0.1%.

The round pitch indicator also changes according to the pitch

speed.

mote control transmitter.

Note:

This unit does not come with an infrared remote control trans-

mitter.

Please contact your dealer for more information on available

remote controls for this CD player.

Playing a CD

Tip:

Playing a CD

If preset menu item No.19 ”Alert:” is set to “On,” playback

Procedure

time display Dstops when the sound is interrupted, and “Inter-

ruption” is displayed in the display section E.

1. Press the POWER button q to turn on the power.

REMAIN

To restore the normal elapsed time display, press any button.

PMD331/PMD340 only:

If preset menu item No.15 “D.OUT:” is set to “Off,” the shock-

proof feature is enabled.

2. Press the button y.

The shockproof feature allows playback to continue without any

interruption in sound (up to 10 seconds) due to data dropout if

the player is subjected to a strong physical shock.

When the disc tray wopens, place a disc on the tray with the

label facing up. Press the button yagain to close the tray.

(It is also possible to close the tray by pressing on it gently. )

Note:

The

button ! flashes, and the CD player pauses at the begin-

The contents of the time display vary if the playing time dis-

play is switched. (See also page 8.)

ning of the first track.

Tips:

- The track operation to be performed after a track is selected,

after the tray is closed, or after the power is turned on can be

selected through a combination of No.1 “AutoCue:” and No.13

“Start:” from the Preset menu.

At the start of a track

In the middle of a track

At the end of a track

Track operation selected through combination of “AutoCue:”

and “Start.”

Preset Menu

“Start:” “AutoCue:”

Off

Action (Initial values bold)

After tray closing or

at Power On:

Stop

After track selection

Play seleted track

Autocue & Pause selected

track

Stop

Off

Pause selected track

Autocue & Pause selected

track

Pause track 1

Autocue & Pause track 1

Pause

Play selected track

Autocue & Pause selected

track

Off

Play track 1

Autocue & pause track 1

Play

When the last track is finished, the disc automatically stops.

- If “AutoCue:” is set to “ON” in the Preset menu, the autocue

function will search for audio that is > – 40dB (Initial value)

and then pause at that point.

Note:

The operation of the CD player at the end of playback varies

according to the playback mode.

(See also page 17.)

(See also page 14.)

Tip:

3. Press the

button !7.

You can select (through the Preset menu) to have “END” flash

on the display C during the last 0 to 35 seconds of a track.

(See also page 17.)

As soon as this button is pressed, the

button !7lights and

playback begins.

Pausing Playback

If the

button !

will blink and playback is paused.

is pressed while a CD is playing, the

To resume playback, press the

button !7again.

The track numberAcurrently being played and the remaining

playing timeDare shown on the display t. At the bottom of

the displayE, the 10-segment bar indicates the playback po-

sition.

Tip:

The changes in the playback state when the

pressed are illustrated below.

button !7 is

Press

PAUSE

STOP

DISC

PLAY

Playing a CD

Disc Elapsed Time

Stopping Playback

Press the button !3.

Playing a CD Again from the First Track

Press the

button !7.

Disc Total Time

Removing a Disc

Press the button yto open the disc tray w, and then remove

the disc. Press the button yagain to close the disc tray w.

Note:

Always close the disc tray wwhen it is not in use.

Searching (Searching for a Desired Position

in a Track)

Tips:

- There is an “Auto Close” feature for the disc tray w. In the

Preset menu, set one of the following for “Auto CLS: OFF”

(initial value), 10 seconds, 30 seconds, 60 seconds, or 180

seconds.

- While playing or in pause, press the

button !

to scan in

the forwards direction.

- While playing or in pause, press the

reverse direction.

button !to scan in the

- If “Tray Lock:” is displayed and the tray does not open even if

the button yis pressed while a track is playing or while

paused, the tray lock setting is set to “On” (initial value). The

setting can be cancelled by switching No.11 “Tray Lock:” on

the Preset menu to “Off:.”

<During playback> Searching

For the first three seconds after the

button !6 or the

button ! is held down, the CD player scans at slow speed

(about 2x normal playing speed).

For the next three seconds, the CD player scans at medium

speed (about 4x normal playing speed).

After that, the CD player scans at high speed (about 16x nor-

mal playing speed).

Changing the Time Display

Pressing the TIME button u cycles the time display through

the following modes:

Track Remaining Time

Track Elapsed Time

If the button !

play position moves one frame.

If the button !or the button !is held down, the search

Frame Searching

or the button ! is pressed once, the

Disc Remaining Time

Disc Elapsed Time

Disc Total Time

speed changes through three stages after every three sec-

onds, until a maximum speed of 75 frames per second (about

1x normal playing speed) is reached.

Playing Time Display Example

Track Remaining Time

Tip:

One frame contains data for about 1/75 of a second of play-

back.

Turning the PITCH/SEARCH dial @has the following effect

(PMD331/PMD340 only):

Frame Searching

Track Elapsed Time

Disc Remaining Time

- Each time the PITCH/SEARCH dial @is turned clockwise,

the play position advances one frame.

- Each time the PITCH/SEARCH dial @is turned counterclockwise,

the play position reverses one frame.

- If the PITCH/SEARCH is turned quickly, the search speed

changes through three stages until a maximum of 75 frames

per second is reached.

Tip:

One frame contains data for about 1/75 of a second of play-

back.

Playing a CD

Using the Pitch Controls

Conducting a Search

PMD330 Only

The disc playback speed can be adjusted in 0.1% increments

Searching Directly

up to +/–12%.

(Searching a Specified Track Number)

Press the NUMERIC (0 to 9) oto specify a track number.

Increasing the Disc Playback Speed

Notes:

-Searching track number 3:

press the “3” button.

Procedure

1. Press the

button !7 to start playing a CD.

-Searching track number 12:

press the “1” button and then the “2” button.

2. Press the PITCH ON/OFF button @ to turn on the pitch control

function.

3. Press the PITCH + button @to increase the disk playback

speed by an increment of 0.1%.

Conducting a Skip Search

- Skipping to Next Track

4. Keep pressing the PITCH + button @to increase the playback

speed continuously.

press the

button !4.

5. Press the PITCH ON/OFF button @ quickly to return to normal

speed.

- Skipping to Previous Track

press the

button !2.

Decreasing the Disc Playback Speed

Tip:

- Press the

button !while once playing a CD to send the

Procedure

player back to the beginning of the current track.

1. Press the

button !7 to start playing a CD.

2. Press the PITCH ON/OFF button @ to turn on the pitch control

function.

3. Press the PITCH - button @to decrease the disk playback

speed by an decrement of 0.1%.

4. Keep pressing the PITCH – button @ to decrease the playback

speed continuously.

5. Press the PITCH ON/OFF button @ quickly to return to normal

speed.

Returning to the Normal Playback Speed

Press the PITCH ON/OFF button @6, and the playback speed

returns to normal.

Notes:

-The right side of the pitch indicator Fshows the positive pitch

speed.

-The left side of the pitch indicator Fshows the negative pitch

speed.

Using the Pitch Controls

Using the A-B Repeat Function

PMD331/PMD340 Only

Procedure

The disc playback speed can be adjusted by a maximum of

1. Press the

button !7to begin playing a CD.

+/– 12% in 0.1% increments.

2. While the CD is either playing or paused at the desired position,

press the A-B button @. The starting point is stored, and “A -”

flashes.

Tip:

When playing two CD players simultaneously, it is possible to

use the pitch bend function on one player to easily adjust the

playback speed so that both CD players are in unison.

Increasing the Disc Playback Speed

Procedure

3. While the CD is either playing or paused at the desired position,

1. Press the

button !7to begin playing a CD.

press the A-B button @. Point B is stored, and “A-B” lights.

2. Press the PITCH ON/OFF button @ to turn on the pitch control

function.

3. Turn PITCH/SEARCH DIAL @

clockwise.

Turn the dial approximately 10 degrees to increase the playback

speed by 0.1%.

Playback starts from point A, and then the segment between

points A and B plays repeatedly.

PITCH/SEARCH DIAL @shows up to +12%.

4. While the PITCH BEND + @button is pressed, the playback

speed increases temporarily by up to 8%.

Clearing Points A and B

Tip:

Pressing the A-B button @ while A-B Repeat playback is in

The disc playback speed changes rapidly when the PITCH

progress clears points A and B.

Tip:

BEND + @ button is pressed. As soon as you release the

button, the playback speed immediately returns to the speed

Points A and B are cleared not only if the A-B button @ is

that was in effect before the button was pressed.

pressed, but also if the button !

is pressed (stopping play-

Note:

back), or if a scan search or direct search is performed.

If “D.OUT” has been set to “On” in the presets, the pitch bend

function will not work.

Decreasing the Disc Playback Speed

Procedure

1. Press the

button !7to begin playing a CD.

2. Press the PITCH ON/OFF button @ to turn on the pitch control

function.

3. Turn PITCH/SEARCH DIAL @

to the counterclockwise.

Turn the dial approximately 10 degrees to decreases the

playback speed by 0.1%.

The PITCH/SEARCH DIAL @ shows up to –12%.

4. While the PITCH BEND – @button is pressed, the playback

speed decreases temporarily by up to 8%.

Tip:

The disc playback speed changes rapidly when the PITCH

BEND – @8button is pressed. As soon as you release the

button, the playback speed immediately returns to the speed

that was in effect before the button was pressed.

Restoring the Normal Playback Speed

Procedure

1. Press the PITCH ON/OFF button @and the playback speed

returns to normal.

Playback Using the Program Function

Registration

To clear a registered Track

It is necessary to register the tracks to use the program function.

Procedure

(For example, to clear P-02.)

1. Press the button !to stop playback, and then press the

PROG button !

2. The program number “P-01” is displayed.

Procedure

(For example, to store P-01, P-02. )

1. Press the button !

PROG button !

2. Input the track number to be registered by pressing the

numeric buttons (0 to 9) o

to stop playback and then press the

At this point, the CUE/CLEAR button !flashes.

At this point, the

/ENTER button !7flashes.

CLEAR

ENTER

CLEAR

ENTER

3. Press the

button !4, so that program number “P-02” is

displayed.

Tip:

3. Press the

/ENTER button !7.

If the

played increases by one. If the

program number that is displayed decreases by one.

4. Press the CUE/CLEAR button !

button !

is pressed, the program number that is dis-

The specified track number is registered in the program as

button ! is pressed, the

“P-01”.

Tip:

Input the track number within five seconds. If the track number

is not input within five seconds, it is cancelled.

4. The program number than changes to “P-02”.

5. Input the next track number to be registered by pressing

the numeric buttons (0 to 9) o.

“P-02” is cleared and “P-02 Trk - -” is displayed on the

display E .

6. Press the

/ENTER button !7.

The specified track number is registered in program “P-02”.

7. The program number than changes to “P-03”.

Switching Program Playback OFF

8. When you have registered all the required tracks, press

Procedure

the PROG button ! or the /EXIT button !3.

1. Press the MODE button @2.

The CD player will then exit the program registration mode

2. Select the playback mode so that “Program: On” is displayed

and enter the program play mode.

in the character display portion of the display t.

Tips:

3. Press either the

the display to “Program: Off”.

4. Press the /ENTER button !

button !or the

button !to change

- A maximum of 20 tracks can be registered in the program.

- To stop program registration, press the PROG button ! or

the /EXIT button !

- Program play can be switched off via the MODE menu.

to confirm the setting.

5. Press the /EXIT button !to exit the playback mode menu.

6. When the button !is pressed, normal playback begins.

Playback Using the CUE Function

Setting the CUE Point

Checking the CUE Point

Procedure

(Setting)

1. Press the

button !

to begin playing a CD.

1. Press the CUE button !

moves to the CUE point, and pauses there.

2. Hold down the CUE button !

. The CD player immediately

Tip:

It is possible to use the search, skip scan or direct search func-

tions to find the approximate position from where you wish to

begin playback.

Playback starts from the CUE point.

Playback stops when the CUE button !is released, and

then the CD player returns to the CUE point and pauses.

Tips:

- Once a cue point has been set, the CD player plays while

holding the CUE button !. Playback returns to the cue point

when released.

The concept of CUE play is illustrated below.

2. Press the

button !to pause the disc at the approximate

position from where you wish to mark the CUE point.

3. Use the

button !and the

button !to search for the

exact position from where you wish to mark the CUE point.

Use the

button !to reverse one frame and then pause.

button !to advance one frame and then pause.

Press & Hold

Release

If you hold down either the

button !

or the

button

!, the rate at which the frames reverse or advance changes

while the button is being held down.

(PMD331/PMD340 only)

Tip:

PAUSE

It is also possible to use the PITCH/SEARCH dial @to find the

PLAY

exact position.

CUE

Point

DISC

4. Press the CUE button !to store the CUE point.

The CUE point is set at this position.

At this point, the CUE button ! stops flashing and remains lit.

“CUE Stored” appears on the display.

- When the player is in CUE playback made (CUE button held

down), it is easy to change to normal playback by also pressing

shortly the

button !. Both the CUE and the

button !

can be released now and the player will continue playback.

CLEAR

Press & hold

Press

Release

PAUSE

PLAY

DISC

Playback Using the CUE Function

Beginning playback from the CUE point

Erasing the CUE Point

Procedure

(Playback)

1. Press the CUE button !

(Erase)

1. Press the button !

to stop playback, and then press the

The CD player immediately moves to the CUE point, and

button !again to erase the cue point. If the cue point is

pauses there.

erased, the CUE button ! turns off.

2. Press the

button !7. Playback starts from the CUE

point.

PMD331/PMD340 only:

If the CD player is in the paused state and the

CLEAR

button !is

pressed, playback from the CUE point starts without any delay.

Note:

This function is called “Instant Start.”

The CUE point is also erased if you press the button y to

open the disc tray w, or if you press the POWER switch q

and turn the CD player off.

Tip:

It is easy to return to the CUE point after the point has been set.

The concept of CUE play is illustrated below.

Resetting the CUE Point

Repeat the procedure described on page 12 in “Setting the

CUE Point,” starting from step 1.

Press

ENTER

If the CD player is kept in the paused state for an extended

Period of time

PAUSE

PLAY

If the CD player is left in the paused state for an extended

period of time without performing any operations, it automati-

cally enters the “auto standby” state.

CUE

Point

DISC

In the auto standby state, the disc stops and “Standby” is indi-

cated on the display.

To release the CD player from the auto standby state, press

the

When you press the

the position that it was at previously and then pauses.

If you press the CUE button ! while the CD player is in the

button !

button !, the CD player searches for

auto standby state, it searches for the CUE point and then

pauses there.

Tip:

The amount of time the unit waits before if enters the “auto

standby” state can be selected in the preset menu: 30 minutes

(initial value), 20 minutes, 10 minutes, or 30 seconds.

Playback Modes

Setting the Playback Mode

Playback Mode Chart

Functions, LCD Display, and Initial Values

Procedure

Setting items

Initial value(bold)

Playback mode

(LCD display)

1. Press the MODE button @

The /ENTER button !

NO.

Function

lights.

Selects the operation

when playback

of a single track ends.

Stop

Cue

Single:

Off

One of the playback modes and the current setting appear

Selects whether to use

on the display E.

Program:

Random:

Off

program playback or not.

Selects whether to use

random playback or not.

Selects whether to

repeat playback or not.

Tip:

All

For the items that can be set in playback mode, refer to the

Playback Mode Chart.

Repeat:

Off

Single

track repeat

2. Press the MODE button @in order to scroll through the

playback modes.

Tips:

Tip:

- This CD player is equipped with a “power-on auto repeat play

back” function.

It is also possible to scroll through the items in the playback

mode menu by pressing the INDEX+ button @ or the INDEX–

button @

3. Use the

of the displayed mode.

At this point, the /ENTER button !changes from being

The “power-on auto repeat playback” function begins playing

automatically if the CD player is turned on while there is a CD

in the disc tray.

button !or the

button !to change the setting

In order to use the “power-on auto repeat playback” function,

you must make the following two settings beforehand:

1) Select “Single:Off” for play back mode function No.1.

2) Select “Repeat:All” for playback mode function No.4.

3) Select “Auto Cue:Off” for preset function No.1.

4) Select “Start:Play” for preset function No.13.

- The playback mode that is currently set is stored in memory,

and becomes the initial setting the next time that the power is

turned on.

steadily lit to flashing .

ENTER

4. Press the

At this point, the

flashing to steadily lit.

/ENTER button !

to confirm the change.

/ENTER button !changes from being

If there is a disc in the tray, playback begins automatically in

“all track repeat” mode when the power is turned on.

Tip:

Note:

Press the CUE/CLEAR button !to cancel a change before it is

If you have set “Yes” for “Reset?” in the preset menu, the

initial value for the playback mode is also restored.

confirmed.

Checking the Playback Mode

ENTER

Procedure

Pressing the MODE button @ causes the various playback

5. Press the /EXIT button !

to exit the setting menu and

modes to be displayed on the screen.

return to the stopped state.

Tip:

The following playback modes can be selected in combination:

single-track playback (“Single”), program playback (“Pro-

gram”), random playback (“Random”) and repeat playback

(“Repeat”).

Synchro Recording

3. When the CD player finishes playing, it stops and the cassette

Using Synchro Recording

recorder enters the paused state.

4. To continue recording, repeat this procedure, starting from

step 2.

This CD player has a CD SYNC function that makes it easy to

record for this CD player to be used in combination with a cas-

sette recorder.

Tips:

- The CD SYNC function works in combination with a cassette

deck that is equipped with the synchro recording function.

- Connect the remote control jack (RC5) output bon this CD

player to the (RC5) input on the cassette deck, and then prepare

the cassette deck for synchro recording.

- When performing synchro recording with a non-cassette recorder,

such as a CD-R or CD-RW recorder, the operation may differ,

so check the instruction manual provided with your recorder.

- When performing synchro recording, set preset menu No.17

“CD sync” to “On”.

Refer to figure 2 for the connection method.

- Make sure to set preset menu item No.1 “Auto Cue” to “Off”

and No.13 ”Start” to “Play” or “Stop” before utilizing CD Sync

function.

Procedure

1. Put the cassette recorder into the synchro recording mode.

2. With the CD player in the stopped state, press the

( See also page 17.)

button !

to start playing the CD.

The cassette recorder automatically begins recording.

Using a Remote Control (Not Included)

- This CD player can receive signals directly from an infrared remote control transmitter within about 5 meters (15 feet.) Note that the

CD player might not operate correctly if the remote control transmitter is not pointed in the direction of the sensor on the CD player,

or if there is an obstacle between the transmitter and the sensor.

Area where an infrared remote control transmitter can be used

約5m

Approximately 5 meters

CD player (This unit)

(15 feet)

60°

-B

60°

The figure depicts the PMD331/PMD340.

Infrared remote cont^赤ro^外l^線t^リra^モn^コs^ンm^送i^信tt^機er

RC5 Code chart

Command

Play

Cord

Command

Cord

- This CD player can be controlled through its infrared sensor

on the front panel when it receives remote control signals

2053

Mode

2036-10

2041-12

2043-10

2088

Pause

2048

Preset

that supports RC5 signals as shown in the table at right.

These remote control codes can also be used if sent through

the RC5 remote control jack b found on the rear panel of the

CD player.

Cue

2059-10

2054

END monitor

Stop

CD-TEXT

2052

2000

FR(REW)

Index +

Index -

2050

2001

2034

2002

2035

2003

Tip:

2032

2004

Because the infrared remote sensor @ on the front panel of

Pitch +

Pitch -

2033

2005

the CD player and the RC5 remote control input jack on the

rear panel of the CD player both support the RC5 codes listed

in the table at right, this CD player can be controlled through

the infrared remote control sensor of any device that supports

RC5 codes.

2038

2006

2039

2007

Pitch Bend +

Pitch Bend -

A - B

2038-10*

2039-10*

2059

2008

2009

CD Sync start 1856

CD Sync stop 1857

Program

Pitch On/Off

Open/Close

Time

2041

2037

2045

2011

* Remote control codes that are marked with an asterisk are

not supported by the PMD330.

CD-TEXT Information Display

Text information that is stored on a CD-TEXT disc can be dis-

played in the sequence shown below by pressing the TEXT

button i.

However, because the information that is recorded differs for

each disc, it is possible that not all of the information listed

below can be displayed.

This CD player automatically skips any items that are not re-

corded on the disc.

Tip:

CD TEXT

Discs that support CD-TEXT are labeled with the

mark.

Note:

If a disc contains no CD-TEXT information, the message “No

CD-TEXT” is displayed when the TEXT button iis pressed.

When stopped

The TEXT button ican be pressed to cycle through the items

shown below.

Displayed Contents

Album Title

Performer

Song Writer

Composer

Arranger

Message　　　

During playback

The TEXT button ican be pressed to cycle through the items

shown below. The information that is displayed pertains to the

track that is currently playing.

Displayed Contents

Track Title

Performer

Song Writer

Composer

Arranger

Message

Track Remain Time Bar

Using the Preset Menu

6. Press the

/ENTER button !

to confirm the selection.

Changing the Preset Settings

Procedure

At this point, the

flashing to steadily lit.

/ENTER button !changes from being

1. Press the button !to put the CD player in the stopped

mode.

2. Press the PRESET button !

The /ENTER button !light.

ENTER

3. An item that can be set as a preset appears on the display

E. (Refer to the Preset menu table for a list of these items.)

Tip:

4. Press the PRESET button !in order to scroll through the

Press the CUE/CLEAR button !to cancel a setting before it is

preset items.

confirmed.

Tip:

Note:

It is also possible to scroll through the items by pressing the

INDEX+ button @or the INDEX– button @

5. Use the button !or the button !

setting of the displayed preset. At this point, the

If “D.OUT” is set to “On,” the instant start, shockproof, and

pitch bend functions will not work.

to change the

/ENTER

changes from being steadily lit to flashing.

button !

ENTER

Preset Menu Chart: Functions, LCD Display, and Initial Values

The settings shown in (bold) are the initial settings.

Presetting items / Function

LCD Display

Auto Cue:

No.

Selects the Auto Cue function. If this item is set to "On",

the CD sync function will not work.

Selects the sound level at which the Auto Cue function

operates.

Selects the End Monitor playing time.

Selects the time at which END starts to flash.

Selects the fade-in time.

Selects the fade-out time.

Selects the delay when going from paused to the start

of playing.

Off

- 40dB, - 90dB to - 35dB in 5dB Steps

10s 15s 20s 25s 30s

AC Lev:

35s

END Mon:

END Warn:

FadeIn:

FadeOut:

Delay:

5s 10s 20s 25s 30s 35s

15s

0s to 8.0s in 0.5s Steps

0ms

100ms

200ms

300ms

400ms

Selects the time display mode when the power is turned on. Time:

Trk REM

Track

Remain

Dsc REM Dsc ELP

Trk ELP

Track

Elapsed

Dsc TTL

Disc

Remain

Disc

Elapsed Disc Total

Enables/disables key lock.

KeyLock:

Off

When key lock is "On", only the POWER qand

PRESET !buttons function.

Selects whether to enable or disable control buttons during FaderLok:

playback that was initiated using "fader start." During playback,

only the POWERq,TIME uand TEXT ibuttons can

be used. All buttons can be used when playback is paused.

Off

Enables/disables the OPEN/CLOSE button while playing.

Selects the auto close time for the disc tray.

TrayLock:

AutoCLS:

Off

10s

30s

60s

180s

Stop

Selects the operation that is performed after a disc is loaded Start:

in the disc tray and after a track is selected.

Pause

Play

Refer to page 7 for a complete explanation of each setting.

Selects the wait time before the CD player enters auto

standby.

Selects whether to output digital signals or not.

If this item is set to "ON," the instant start, shockproof, and

pitch bend functions will not work.

Enables/disables the Control I/O (D-sub 25-pin) ⁄input jack Remote:

(PMD331/PMD340) or the fader start input jack (PMD330)c.

Enables/disables the CD Sync function.

AutoSTBY:

D.OUT:

30m

30min

20m

20min

10m

10min

30sec

30s

*15

Off

CD Sync:

Selects whether to output the CD Sync signal through the

RC5 jack b when playback starts.

Off

Turn Auto Cue (preset #1) "Off" to utilize the CD sync function.

Selects which Index (#2 or #3) will trigger an output on

pin #11 on the Control I/O Port.

Selects whether or not to display a warning when a skip

occurs as a result of a bad CD.

Index:

Alert:

*18

Off

Selects the CD-TEXT display language.

Selects whether or not to restore the original presets.

Text:

Reset?:

English

French

Spanish

Yes

German

* Those items marked with an asterisk can only be selected on the PMD331/PMD340. They are not displayed on the PMD330.

Using the Control Port (PMD331/PMD340 Only)

The control port is an input/output jack for remote control (D-SUB 25-pin female connector). Different contact circuits (switches,

etc.) can be connected to each input.

In addition, the CD player can be monitored or can provide control to a remote location by using to the output jacks.

Notes:

-The maximum output current on pin 12 (Tally power supply) is 80 mA.

-Use a D-sub 25-pin male connector. (Threaded portion: 4-40 UNC)

-When connecting such a connector, refer to the connection examples illustrated below.

Tip:

- To enable the input from the control I/O jack, set preset menu No. 16 “Remote” to “On”. (See also page 17.)

Table of Control Input/Output Signals

Signal name

PLAY TALLY

I/O

Port specification

Function

On while playing

No.

TTL (Ii < 20 mA)

HCMOS

On while paused

PAUSE TALLY

CUE TALLY

STOP

Equivalent to CUE LED

Equivalent to STOP button

Equivalent to

button

HCMOS

Equivalent to INDEX -

INDEX -

HCMOS

Equivalent to

button

PITCH +

HCMOS

Equivalent to PITCH +

Equivalent to PITCH button