Clarion DRX8675z User Manual

Owner’s manual  
Mode d’emploi  
Manual de instrucciones  
DRX8675z  
AM/FM CD PLAYER  
WITH CD/MD CHANGER CONTROL  
COMBINÉ RADIO/CD AM/FM AVEC PILOTE  
DE CHANGEUR CD/MD  
RADIO DE AM/FM Y REPRODUCTOR DE DISCOS  
COMPACTOS CON CONTROL DE CAMBIADOR  
DE DISCOS COMPACTOS/MINIDISCOS  
OPEN  
DRX8675z  
ISR  
1
2
3
4
5
6
Clarion Co., Ltd.  
PE-2332B  
280-7401-00  
All Rights Reserved. Copyright © 1999: Clarion Co., Ltd.  
Printed in China / Imprimé en Chine / Inpreso en China  
1999/8 (CL·C)  
Handling Compact Discs  
6. REMOTE CONTROL  
2. PRECAUTIONS  
Use only compact discs bearing the  
mark.  
Receiver for remote control unit  
1. When the inside of the car is very cold and  
the player is used soon after switching on  
the heater moisture may form on the disc or  
the optical parts of the player and proper  
playback may not be possible. If moisture  
forms on the disc, wipe it off with a soft cloth.  
If moisture forms on the optical parts of the  
player, do not use the player for about one  
hour. The condensation will disappear natu-  
rally allowing normal operation.  
3. When the auto antenna cord is connected to  
the car auto antenna cord, when the unit is  
switched to the radio mode (or theTV mode),  
the antenna is extended automatically. If the  
car is in a narrow space, the antenna may  
strike something, so be careful.  
Do not play heart-shaped, octagonal, or other specially shaped compact discs.  
OPEN  
To remove a compact disc from its storage  
Handling  
DRX8675z  
case, press down on the center of the case  
and lift the disc out, holding it carefully by the  
edges.  
Do not use commercially available CD protec-  
tion sheets or discs equipped with stabilizers,  
etc. These may damage the disc or cause  
breakdown of the internal mechanism.  
• New discs may have some roughness around  
the edges. If such discs are used, the player  
may not work or the sound may skip. Use a  
ball-point pen or the like to remove any rough-  
ness from the edge of the disc.  
ISR  
1
2
3
4
5
6
4. This unit uses a precision mechanism. Even  
in the event that trouble arises, never open  
the case, disassemble the unit, or lubricate  
the rotating parts.  
Operating range: 30° in all directions  
Ball-point pen  
Roughness  
2. Driving on extremely bumpy roads which  
cause severe vibration may cause the sound  
to skip.  
Storage  
Remote control unit  
Signal transmitter  
Do not expose compact discs to direct sun-  
light or any heat source.  
Do not expose compact discs to excess hu-  
midity or dust.  
Do not expose compact discs to direct heat  
from heaters.  
This equipment has been tested and found to  
comply with the limits for a Class B digital de-  
vice, pursuant to Part 15 of the FCC Rules.  
CAUTION  
USE OF CONTROLS, ADJUSTMENTS, OR  
PERFORMANCE OF PROCEDURES OTHER  
THAN THOSE SPECIFIED HEREIN, MAY RE-  
SULT IN HAZARDOUS RADIATION EXPO-  
SURE.  
These limits are designed to provide reason-  
able protection against harmful interference in  
a residential installation.  
Never stick labels on the surface of the com-  
pact disc or mark the surface with a pencil or  
pen.  
Never play a compact disc with any cellophane  
tape or other glue on it or with peeling off marks.  
If you try to play such a compact disc, you may  
not be able to get it back out of the CD player  
or it may damage the CD player.  
Do not use compact discs that have large  
scratches, are misshapen, cracked, etc. Use  
of such discs may cause misoperation or dam-  
age.  
Cleaning  
To remove fingermarks and dust, use a soft  
cloth and wipe in a straight line from the cen-  
ter of the compact disc to the circumference.  
Do not use any solvents, such as commercially  
available cleaners, anti-static spray or thinner  
to clean compact discs.  
This equipment generates, uses, and can radi-  
ate radio frequency energy and, if not installed  
and used in accordance with the instructions,  
may cause harmful interference to radio com-  
munications. However, there is no guarantee  
that interference will not occur in a particular  
installation.  
THE COMPACT DISC PLAYER and MINI DISC  
PLAYER SHOULD NOT BE ADJUSTED OR  
REPAIRED BY ANYONE EXCEPT PROPERLY  
QUALIFIED SERVICE PERSONNEL.  
CHANGES OR MODIFICATIONS NOT EX-  
PRESSLY APPROVED BY THE MANUFAC-  
TURER FOR COMPLIANCE COULD VOID  
THE USER’S AUTHORITYTO OPERATETHE  
EQUIPMENT.  
After using special compact disc cleaner, let  
the compact disc dry off well before playing it.  
If this equipment does cause harmful interfer-  
ence to radio or television reception, which can  
be determined by turning the equipment off and  
on, the user is encouraged to consult the dealer  
or an experienced radio/TV technician for help.  
INFORMATION FOR USERS:.  
CHANGES OR MODIFICATIONS TO THIS  
PRODUCT NOT APPROVED BY THE MANU-  
FACTURER WILL VOID THE WARRANTY  
AND WILL VIOLATE FCC APPROVAL.  
Flip Down Panel  
Inserting the Batteries  
MODEL  
This unit uses a flip-down structure that makes possible large-size displays.  
12V  
GROUND  
1. Turn the remote control unit over, then slide  
the rear cover in the direction of the arrow.  
3. Do not use the FLIP DOWN PANEL as a tray  
AM 530-1710kHz/FM 87.9-107.9MHz  
CAUTION  
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.  
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:  
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND  
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,  
INCLUDING INTERFERENCE TAHT MAY CAUSE UNDESIRED  
OPERATION.  
to place objects on when it is open.  
AA (UM-3/1.5V)  
Batteries  
When opening and closing the FLIP DOWN  
PANEL, be careful not to catch your fingers.  
They could be injured.  
2. Insert the AA (UM-3/1.5V) batteries that came  
with the remote control unit facing in the  
directions shown in the figure, then close the  
rear cover.  
4. When closing the FLIP DOWN PANEL, do not  
press OPEN button 1 .  
THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR  
SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.  
5. Strong impacts to the operating or display  
section can cause damage or deformation.  
CLARION CO.,LTD.  
50 KAMITODA,TODA-SHI,SAITAMA-KEN,JAPAN  
1. Always use this unit with the FLIP DOWN  
PANEL closed.  
6. If the FLIP DOWN PANEL does not open fully,  
gently open it with your hand.  
Notes:  
051 722 877  
Rear cover  
Using batteries improperly can cause them to ex-  
plode. Take note of the following points:  
When replacing batteries, replace both batteries  
with new ones.  
Do not short-circuit, disassemble or heat batteries.  
Do not dispose of batteries into fire or water.  
Dispose of spent batteries properly.  
MANUFACTURED:  
2. Do not force operations or use this device ab-  
normally when opening or closing the FLIP  
DOWN PANEL.  
Rear side  
286-  
Clarion Co.,Ltd.  
MADE IN  
SERIAL No.  
PE-  
Bottom View of Source Unit  
Be sure to unfold and read the next page.  
Veuillez déplier et vous référer à la page suivante.  
Cerciórese de desplegar y de leer la página siguiente.  
8
DRX8 6 7 5 z  
DRX8 6 7 5 z  
3
DRX8 6 7 5 z  
4
3. CONTROLS / LES COMMANDES / CONTROLES  
4. NOMENCLATURE  
5. DCP  
Note:  
The control panel can be detached to prevent theft. When detaching the control panel, store it in the  
DCP (DETACHABLE CONTROL PANEL) case to prevent scratches.  
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).  
Source unit / Appareil pilote / Unidad fuente  
We recommend taking the DCP with you when leaving the car.  
Names of Buttons  
Removing the DCP  
1. Hold down POWER button 3 for 1 second  
Attaching the DCP  
1. Insert the right side of the DCP into the source  
unit.  
1
OPEN button  
9
Preset buttons (1 to 6)  
Direct buttons (1 to 6) (7 to 12)  
DISP (display) button  
ISR (instant station recall) button  
BND (band) button  
TOP button  
2
ENT (enter) button  
OPEN  
or longer to turn off the power.  
DRX8675z  
Play/pause button  
!
2. Insert the left side of the DCP into the source  
unit.  
3
4
5
POWER button  
"
#
2.  
FNC (function) button  
TITLE button  
ISR  
1
2
3
4
5
6
ADJ (adjust) button  
PS/AS (preset scan/auto store) button  
SCN (scan) button  
$
A-M (audio mode) button  
LOUD (loudness) button  
SEARCH button  
%
&
(
2. Deeply push in OPEN button 1 to unlock  
1.  
6
7
8
RPT (repeat) button  
RDM (random) button  
Z-EHCR (z-enhancer) button  
Rotary knob  
the FLIP DOWN PANEL.  
With the FLIP DOWN PANEL opened / Ouverture du PANNEAU RABATTABLE /  
Apertura del PANEL ABATIBLE  
If the FLIP DOWN PANEL does not open fully,  
gently open it with your hand.  
CD insertion slot  
)
Eject button  
CAUTION  
• The DCP can easily be damaged by shocks.  
After removing it, be careful not to drop it  
or subject it to strong shocks.  
Display Items  
• If the FLIP DOWN PANEL is kept open, the  
DCP may drop due to vibration of the car.  
1
2
3
4
5
6
7
8
9
Single disc indication  
Disc in indication  
$
A-M (audio mode) indication  
LD (loudness) indication  
Graphic indication  
3. Pull the DCP toward you and remove it.  
%
&
This results in damage to the DCP. So close  
the FLIP DOWN PANEL or remove the DCP  
to store into the case.  
EASY mode indication  
G.EQ indication  
DCP  
Levels are displayed in adjusting the volume,  
etc.  
• The connector connecting the source unit  
and the DCP is an extremely important part.  
Be careful not to damage it by pressing on  
it with fingernails, screwdrivers, etc.  
DSP indication  
(
)
Long title indication  
PRO (professional) mode indication  
P.EQ indication  
When the texts for CD or MD are more than  
11 characters, this indication lights.  
Display / Afficheur / Visualizador  
Note:  
S.EQ indication  
Operation status indication  
• If the DCP is dirty, wipe off the dirt with a soft, dry  
cloth only.  
Preset channel indication (1 to 6)  
Disc number indication (1 to 12)  
The frequency, play time, clock, etc. are  
displayed.  
4. Close the HOLD FLAP.  
~
+
,
RDM (random) indication  
RPT (repeat) indication  
SCN (scan) indication  
DISC indication  
The disc numbers corresponding to the discs  
in the CD or MD changer light.  
!
ST (stereo) indication  
"
#
MANU (manual) indication  
Function mode indication  
-
.
Z-EHCR (z-enhancer) indication  
HOLD FLAP  
The names of modes being selected, etc. are  
displayed.  
CAUTION  
Be sure to close the HOLD FLAP for safety  
when removing the DCP.  
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.  
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.  
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.  
5
DRX8 6 7 5 z  
6
DRX8 6 7 5 z  
DRX8 6 7 5 z  
7
Functions of Remote Control Unit Buttons  
CD changer  
MD changer  
Mode  
Radio  
CD  
TV  
Button  
,
FUNC  
Turns power on and off. When pressed and held for 1 second: Turns power off.  
Switches among radio, CD, CD changer, MD changer and TV.  
-
BAND  
DISC UP  
Plays the first track. Moves the next disc  
Top play. in increasing order.  
Switches reception  
band.  
Switches reception  
band.  
PROG  
TOP  
Increases and decreases volume (in all modes).  
.
VOLUME  
SEARCH  
/
Moves preset  
channels up and  
down.  
Moves tracks up  
and down.  
Moves tracks up  
and down.  
Moves preset  
channels up and  
When pressed and When pressed and down.  
held for 1 second:  
Fast-forward/  
fast-backward.  
held for 1 second:  
Fast-forward/  
fast-backward.  
:
PLAY/PAUSE  
No function.  
Switches between  
Switches between  
No function.  
playback and pause. playback and pause.  
Turns mute on and off.  
;
MUTE  
ISR  
Recalls ISR radio station in memory.  
<
Press and hold for 2 seconds or longer: Stores current station into ISR memory (radio  
mode only).  
Switches among main display, sub display, clock display and spectrum analyzer display  
(only when connected to DPH7500z).  
=
>
DISP  
Preset scan.  
Scan play.  
Scan play.  
Preset scan.  
SCN  
When pressed and  
held for 2 seconds:  
Auto store.  
When pressed and When pressed and  
held for 1 seconds: held for 2 seconds:  
PS/AS  
Disc scan play.  
Auto store.  
No function.  
Repeat play.  
Random play.  
Repeat play.  
No function.  
?
RPT  
BLS  
When pressed and  
held for 1 seconds:  
Disc repeat play.  
No function.  
Random play.  
When pressed and TV and VTR.  
held for 1 seconds:  
Switches between  
@ RDM  
DOLBY NR  
MONI  
Disc random play.  
* Some of the corresponding buttons on the source unit and remote control unit have different functions.  
DRX8 6 7 5 z  
9
7. OPERATIONS  
Note: Be sure to read this chapter referring to the front diagrams of  
chapter “3. CONTROLS” on page 5 (unfold).  
Basic Operations  
Radio mode CD mode CD changer mode  
MD changer mode TV mode Radio  
CAUTION  
mode...  
Be sure to lower the volume before switching  
off the unit power or the ignition key.The unit  
remembers its last volume setting. If you  
switch the power off with the volume up, when  
you switch the power back on, the sudden  
loud volume may hurt your hearing and dam-  
age the unit.  
External equipment not connected with CeNET  
is not displayed.  
Adjusting the volume  
Turning the Rotary knob & clockwise increases  
the volume; turning it counterclockwise de-  
creases the volume.  
The clock is displayed when the ignition key  
is turned to the ACC (accessory) or IGN (igni-  
tion-on) position even when the unit power  
is off. In some cars, the clock may momen-  
tarily disappear when the ignition key is  
turned to the START position. The clock will  
reappear after the engine has started and the  
ignition key is released to the IGN (ignition-  
on) position.  
The volume level is from 0 (minimum) to 33 (maxi-  
mum).  
Switching the display  
Press DISP button ! to select the desired display.  
Each time you press DISP button ! , the display  
switches in the following order:  
Main display  
Turning on/off the power  
Note:  
Be careful about using this unit for a long time with-  
out running the engine. If you drain the cars bat-  
tery too far, you may not be able to start the en-  
gine and this can reduce the service life of the  
battery.  
1. Press POWER button 3 .  
Sub (title) display  
2. The illumination and display on the unit light  
up. The unit automatically remembers its last  
operation mode and will automatically switch  
to display that mode.  
3. Press and hold POWER button 3 for 1 sec-  
ond or longer to turn off the power for the unit.  
Note:  
Clock display  
System check  
The first time this unit is turned on after the wire  
connections are completed, it must be checked  
what equipment is connected. When the power is  
turned on, SYSTEM CHCKappears in the  
display, so press POWER button 3 . The system  
check starts within the unit.When the system check  
is complete, the power is turned off, so press  
POWER button 3 again.  
Spectrum analyzer display  
Selecting a mode  
1. Press FNC button 3 to change the mode of  
operation.  
2. Each time you press FNC button 3 , the mode  
of operation changes in the following order:  
Main display...  
10  
DRX8 6 7 5 z  
Basic Operations  
The spectrum analyzer display is only displayed  
decreases the output volume.  
when the DPH7500z is connected.  
* The factory default setting is “4”.  
(Setting range: 0 to 7)  
Once selected, the preferred display becomes  
the display default.When a function adjustment  
such as volume is made, the screen will  
momentarily switch to that function’s display,  
then revert back to the preferred display sev-  
eral seconds after the adjustment.  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
When you have entered a title in a CD, it  
appears in the sub display. If you have not  
entered a title, “NO-TTL” appears in the title  
display instead. For information on how to enter  
a title, refer to the subsection “Entering titles”  
in the “Other Handy Functions”.  
Setting tone bypass  
The tone bypass disables the tone (bass and  
treble) functions and cuts the noise generated  
when the tone functions are on.  
1. Press A-M button $ and select “TONE BYPASS”.  
2. Turning the Rotary knob & clockwise sets the  
tone bypass to “YES” (ON); turning it  
counterclockwise sets the tone bypass to  
NO” (OFF).  
Setting the Z-enhancer  
This unit comes with 3 types of sound tone effects  
stored in memory. Select the one you prefer.  
The factory default setting is “Z-EHCR OFF”.  
Each time you press Z-EHCR button 8 , the tone  
effect changes in the following order:  
The factory default setting is “NO” (OFF).  
If the setting is “YES” (ON), the bass and treble  
adjustments cannot be made.  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
Z-ENHANCER 1Z-ENHANCER 2Z-  
ENHANCER 3Z-EHCR OFFZ-  
ENHANCER 1”...  
Note:  
• Z-ENHANCER 1 : bass emphasized  
• Z-ENHANCER 2 : treble emphasized  
• Z-ENHANCER 3: bass and treble emphasized  
If you set the Z-ENHANCER function to ON (1 to  
3), you cannot set the tone bypass.  
• Z-EHCR OFF  
: no sound effect  
Adjusting the bass  
1. Press A-M button $ and select “BASS”.  
Adjusting the tone  
Press A-M button $ and select the item to adjust.  
Each time you press A-M button $ , the item  
changes in the following order:  
2. Turning the Rotary knob & clockwise empha-  
sizes the bass; turning it counterclockwise  
attenuates the bass.  
The factory default setting is “0”.  
(Adjustment range: – 6 to +6)  
When the Z-enhancer and tone bypass are off  
NON-FAD VOLTONE BYPASS➜  
BASSTREBLEBALANCE➜  
FADERFunction mode...  
The bass cannot be adjusted if the tone by-  
pass setting is “YES” (ON).  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
When Z-enhancer 1, 2 or 3 is set  
NON-FADVOLZ-EHCRBALANCE”  
FADERFunction mode...  
Note:  
Adjusting the treble  
1. Press A-M button $ and select “TREBLE”.  
When the separately-sold digital sound processor  
(DPH7500z) is used, the tone bypass, bass and  
treble tone adjustments cannot be selected. To  
adjust the tone, refer to the chapter DSP  
Operations.  
2. Turning the Rotary knob & clockwise empha-  
sizes the treble; turning it counterclockwise  
attenuates the treble.  
The factory default setting is “0”.  
(Adjustment range: – 6 to +6)  
The treble cannot be adjusted if the tone by-  
pass setting is “YES” (ON).  
Adjusting the non-fader output volume  
You can adjust the volume output from the unit’s  
non-fader output terminal.  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
1. Press A-M button $ and selectNON-FADVOL”.  
2. Turning the Rotary knob & clockwise increases  
the output volume; turning it counterclockwise  
DRX8 6 7 5 z  
11  
Basic Operations  
Adjusting the balance  
Turning on/off the loudness  
1. Press A-M button $ and select BALANCE.  
The loudness effect emphasizes the bass and  
treble to create a natural sound tone. When you  
are listening to music at a low volume, it is rec-  
ommended to use the loudness effect.  
2. Turning the Rotary knob & clockwise empha-  
sizes the sound from the right speaker; turn-  
ing it counterclockwise emphasizes the sound  
from the left speaker.  
1. Press and hold LOUD button $ for 1 second  
or longer to turn on the loudness effect.When  
the loudness effect is turned on, LDlights in  
the display.  
The factory default setting is 0. (Adjustment  
range: L13 to R13)  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
2. Press and hold LOUD button $ for 1 second  
or longer to turn off the loudness effect. LD”  
goes off in the display.  
Adjusting the fader  
1. Press A-M button $ and select FADER.  
Note:  
When using a sold separately digital sound pro-  
cessor (DPH7500z), a feature called auto loud-  
ness is selected.This function is different from the  
loudness effect. For further details on the auto loud-  
ness feature, refer to the subsection Output  
adjustment of auto loudness, subwoofer and  
playback band.  
2. Turning the Rotary knob & clockwise empha-  
sizes the sound from the front speakers; turn-  
ing it counterclockwise emphasizes the sound  
from the rear speakers.  
The factory default setting is 0. (Adjustment  
range: F12 to R12)  
3. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
Adjusting the Z-enhancer  
1. Press Z-EHCR button 8 and select the Z-  
enhancer mode (1 to 3) to adjust.  
2. Press A-M button $ and select Z-EHCR.  
3. Turning the Rotary knob & clockwise adjusts  
in the + direction; turning it counterclockwise  
adjusts in the direction.  
When Z-enhancer 1 is selected, you can adjust  
the bass in the range of ±2.  
When Z-enhancer 2 is selected, you can adjust  
the treble in the range of ±2.  
When Z-enhancer 3 is selected, you can adjust  
the bass and treble in the range of ±2.  
4. When the adjustment is complete, press A-M  
button $ several times until the function mode  
is reached.  
Note:  
If you set the Z-ENHANCER function to ON (1 to  
3), you cannot set the tone bypass.  
12  
DRX8 6 7 5 z  
Radio Operations  
2. Press the right or left side of SEARCH button  
% to automatically seek a station.  
FM reception  
®
For enhanced FM performance the  
When the right side of SEARCH button % is  
pressed, the station is sought in the direction  
of higher frequencies; if the left side of  
SEARCH button % is pressed, the station is  
sought in the direction of lower frequencies.  
tuner includes signal actuated stereo control,  
Enhanced Multi AGC, Impulse noise reduction  
circuits and Multipath noise reduction circuits.  
Changing the reception area  
This unit is initially set to USA frequency intervals  
of 10kHz for AM and 200kHz for FM.When using it  
outside the USA, the frequency reception range  
can be switched to the intervals below.  
Manual tuning  
There are 2 ways available:Quick tuning and step  
tuning.  
When you are in the step tuning mode, the  
frequency changes one step at a time. In quick  
tuning mode, you can quickly tune the desired  
frequency.  
1. Press BND button # and select the desired  
band (FM or AM).  
Setting the reception area  
1. Press BND button # and select the desired  
radio band (FM or AM).  
2. While pressing RDM button 7 , each time you  
press and hold the number 1of the Preset  
buttons 9 for 2 seconds or longer, the  
reception area switches from inside the USA  
to outside the USA or from outside the USA to  
inside the USA.  
If MANUis not lit in the display, press and  
hold BND button # for 1 second or longer.  
MANUis lights in the display and manual  
tuning is now available.  
2. Tune into a station.  
Any station preset memories are lost when the  
reception area is changed.  
Quick tuning:  
Press and hold the right or left side of  
SEARCH button % for 1 second or longer to  
tune in a station.  
Listening to the radio  
1. Press FNC button 3 and select the radio  
Step tuning:  
mode.  
Press the right or left side of SEARCH button  
% to manually tune in a station.  
2. Press BND button # and select the radio  
band. Each time the button is pressed, the  
radio reception band changes in the following  
order:  
Recalling a preset station  
FM1 FM2 FM3 AM FM1...  
A total of 24 preset positions (6-FM1, 6-FM2, 6-  
FM3, 6-AM) exists to store individual radio  
stations in memory. Pressing the corresponding  
preset button recalls the stored radio frequency  
automatically.  
3. Press the right or left side of SEARCH button  
% to tune in the desired station.  
Tuning  
1. Press BND button # and select the desired  
There are 3 types of tuning mode available, seek  
tuning, manual tuning and preset tuning.  
band (FM or AM).  
2. Press the corresponding Preset button 9 to  
recall the stored station.  
Seek tuning  
1. Press BND button # and select the desired  
Press and hold one of the Preset buttons 9  
for 2 seconds or longer to store that station into  
preset memory.  
band (FM or AM).  
If MANUis lit in the display, press and hold  
BND button # for 1 second or longer.MANU”  
in the display goes off and seek tuning is now  
available.  
Manual memory  
1. Select the desired station with seek tuning,  
manual tuning or preset tuning.  
2. Press and hold one of the Preset buttons 9  
for 2 seconds or longer to store the current  
station into preset memory.  
DRX8 6 7 5 z  
13  
Radio Operations  
Auto store  
Auto store is a function for storing up to 6 stations  
that are automatically tuned in sequentially. If 6  
stations cannot be received, a previously stored  
station remains unoverwritten at the memory  
position.  
CD Operations  
Loading a CD  
1. Press OPEN button 1 to access the CD  
insertion slot behind the FLIP DOWN PANEL.  
2. Insert a CD into the center of the insertion  
slot with the label side facing up.The CD plays  
automatically after loading.  
1. Press BND button # and select the desired  
Notes:  
band (FM or AM).  
Never insert foreign objects into the CD  
insertion slot.  
2. Press and hold AS button 5 for 2 seconds or  
longer. The stations with good reception are  
stored automatically to the Preset buttons 9 .  
If the CD is not inserted easily, there may be  
another CD in the mechanism or the unit may  
require service.  
Discs not bearing the  
ROMs cannot be played by this unit.  
mark and CD-  
Preset scan  
Preset scan receives the stations stored in preset  
memory in order. This function is useful when  
searching for a desired station in memory.  
Loading 3" (8 cm) compact discs  
* No adapter is required to play a 3" CD.  
* Insert the 3" CD into the center of the insertion  
slot.  
* When a 3" CD is loaded, SINGLElights in  
the display.  
1. Press PS button 5 .  
2. When a desired station is tuned in, press PS  
button 5 again to continue receiving that  
station.  
3. Close the FLIP DOWN PANEL.  
Note:  
Be careful not to press and hold PS button 5 for  
2 seconds or longer, otherwise the auto store  
function engages and the unit starts storing  
stations.  
.
CAUTION  
Be careful not to catch your hand or fingers  
while closing the FLIP DOWN PANEL.  
Notes:  
Instant station recall (ISR)  
If the FLIP DOWN PANEL does not open fully,  
gently open with your hand.  
After loading a CD, always close the FLIP DOWN  
PANEL.  
Instant station recall is a special radio preset that  
instantly accesses a favorite radio station at a  
touch of a button.The ISR function even operates  
with the unit in other modes.  
Listening to a CD already inserted  
ISR memory  
Press FNC button 3 to select the CD mode. Play  
starts automatically.If no CD is loaded in the unit,  
NO DISCappears in the display.  
1. Select the station that you wish to store in ISR  
memory.  
2. Press and hold ISR button " for 2 seconds  
or longer.  
Pausing play  
1. Press Play/pause button 2 to pause play.  
Recalling a station with ISR  
In any mode, press ISR button " to turn on the  
radio function and tune the selected radio station.  
ISRappears in the display. Press ISR button  
PAUSEappears in the display.  
2. To resume CD play, press Play/pause button  
2
again.  
"
again to return to the previous mode.  
Displaying CD titles  
This unit can display title data for CD-text CDs  
and user titles input with this unit.  
1. Press DISP button ! to display the title.  
2. Each time you press and hold DISP button  
!
for 1 second or longer, the title display  
changes in the following order:  
User title (disc) CD-text title (disc) CD-  
text title (track) user title (disc)...  
14  
DRX8 6 7 5 z  
CD Operations  
Note:  
If the CD playing is not a CD-text CD or no user  
title has been input, NO-TTLappears in the  
display.  
Scrolling a CD-text title  
When a CD-text title is longer than 11 characters,  
you can scroll the display as follows.  
1. Display the CD-text title (disc or track).  
DRX8 6 7 5 z  
15  
Other Handy Functions  
Setting the clock  
1. Press and hold ADJ button 4 for 1 second or  
Mode  
Number of titles  
30 titles  
Radio mode  
CD mode  
TV mode  
longer to switch to the adjustment selection display.  
50 titles  
2. Press the right or left side of SEARCH button  
15 titles  
% to select CLOCK.  
CD changer mode  
CDC655z connected  
CDC655Tz connected  
CDC1255z connected  
Number of titles  
60 titles  
3. Press ENT button 2 .  
4. Press the right or left side of SEARCH button  
100 titles  
% to select the hour or the minute.  
50 titles  
5. Turn the Rotary knob & clockwise or  
counterclockwise to set the correct time.  
1. Press FNC button 3 to select the mode you want  
The clock is displayed in 12-hour format.  
to enter a title. (radio, CD, CD changer or TV)  
6. Press ENT button 2 to store the time into memory.  
Titles cannot be entered for MDs with this unit.  
2. Select and play a CD or a CD in the CD changer  
or tune to an appropriate TV or radio station.  
7. Press ADJ button 4 to return to the previous mode.  
Note:  
You cannot set the clock when it is displayed with  
only the ignition on. If you drain or remove the cars  
battery or take out this unit, the clock is reset.While  
setting the clock, if another button or operation is  
selected, the clock set mode is canceled.  
3. Press DISP button ! and display the subtitle.  
4. Press TITLE button 4 . TITLappears in the  
display and the cursor position flashes.  
5. Press the right or left side of SEARCH button  
% to move the cursor.  
Dimmer level setting  
You can reduce the display illumination linked to  
the car illumination.  
6. Press DISP button ! to select a character.  
Each time you press DISP button ! , the  
character changes in the following order:  
The factory default setting is LEVEL 3.  
Capital letters Small letters Numbers ➜  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection display.  
Symbols Umlaut Capital letters...  
7. Turn the Rotary knob & to select the desired  
character. Turning the Rotary knob &  
clockwise moves the cursor to the next  
character; turning it counterclockwise moves  
the cursor to the previous character.  
2. Press the right or left side of SEARCH button  
% to select DIMMER LV.  
3. Press ENT button 2 .  
4. Turn the Rotary knob & clockwise or  
counterclockwise to set the dimmer level.  
Choose the dimmer level from the following.  
8. Repeat steps 5 to 7 to enter up to 10  
characters for the title.  
9. Press and hold ENT button 2 for 2 seconds  
or longer to store the title into memory and  
cancel title input mode.  
OFF,LEVEL 1,LEVEL 2, LEVEL 3,  
LEVEL 4, LEVEL 5.  
LEVEL 1 to LEVEL 5:  
The greater the dimmer level is, the more the  
illumination is reduced.  
Clearing titles  
1. Play a CD or a CD in a CD changer or tune a  
radio station or TV station that you want to  
clear the title for.  
OFF:  
Even if the car illumination is turned on,  
reduction of the display illumination does not  
occur.  
2. Press DISP button ! and display the subtitle.  
3. Press TITLE button 4 . TITLappears in the  
display and the display switches to the title  
input display.  
5. Pressing ENT button 2 returns to the  
adjustment selection display.  
6. Press ADJ button 4 to return to the previous  
4. Press BND button # .  
mode.  
5. Press and hold ENT button 2 for 2 seconds  
or longer to clear the title and cancel the title  
input mode.  
Entering titles  
Titles up to 10 characters long can be stored in  
memory and displayed for radio stations and  
CDs. The numbers of titles that can be entered  
for each mode are as follows.  
16  
DRX8 6 7 5 z  
Other Handy Functions  
Message display  
Adjusting the display contrast  
You can adjust the display contrast according to  
the angle of installation of the unit.  
When the unit is powered on or off, a message is  
displayed.The user can turn this message display  
on or off.  
The factory default setting is 6. (Adjustment level:  
1 to 11)  
The factory default setting is ON.  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection  
display.  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection display.  
2. Press the right or left side of SEARCH button  
2. Press the right or left side of SEARCH button  
% to select MESSAGE.  
% to select CONTRAST.  
3. Press ENT button 2 .  
3. Press ENT button 2 .  
4. Turn the Rotary knob & clockwise to set the  
message display to ON; turn it counterclockwise  
to set the message display to OFF.  
4. Turn the Rotary knob & clockwise or  
counterclockwise to adjust the contrast.  
5. Pressing ENT button 2 returns to the  
5. Pressing ENT button 2 returns to the  
adjustment selection display.  
adjustment selection display.  
6. Press ADJ button 4 to return to the previous  
6. Press ADJ button 4 to return to the previous mode.  
mode.  
NON-FADER output adjustment display on/off  
If you do not want to adjust the non-fader output  
level, you can turn off the NON-FAD VOLdisplay.  
Setting the SEARCH button  
illumination color (Prism function)  
The change in the SEARCH button illumination  
color according to the unit operating state is  
called the Prism function. You can set the  
illumination pattern you prefer.  
The factory default setting is ON.  
Even if you set the level adjustment display to  
OFF, a signal is output from the non-fader output.  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection display.  
The factory default setting is PATTERN 1.  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection  
display.  
2. Press the right or left side of SEARCH button  
% to select NON-FADER.  
3. Press ENT button 2 .  
2. Press the right or left side of SEARCH button  
4. Turn the Rotary knob & clockwise to set the  
non-fader output adjustment display to ON;  
turn it counterclockwise to set the non-fader  
output adjustment display to OFF.  
% to select PRISM KEY.  
3. Press ENT button 2 .  
4. Turn the Rotary knob & clockwise or  
counterclockwise to set the illumination  
pattern. Each time you turn the Rotary knob  
& , the illumination pattern changes in the  
following order:  
ON:  
When A-M button $ is pressed, the NON-  
FAD VOLitem is displayed.  
You can adjust the output level.  
OFF:  
PATTERN 1 PATTERN 2 OFF ➜  
PATTERN 1...  
Even when you press A-M button $ , the  
NON-FAD VOLitem is not displayed.  
PATTERN 1:  
The color changes for each function mode,  
station tuning, scanning and other operations.  
You cannot adjust the output level.  
5. Pressing ENT button 2 returns to the  
adjustment selection display.  
PATTERN 2:  
In addition to the changes in Pattern 1, the  
color changes according to the audio level.  
6. Press ADJ button 4 to return to the previous mode.  
Triggered audio mute for cellular telephones  
OFF:  
This unit requires special wiring to mute the audio  
signal automatically when a cellular telephone  
rings in the car.  
The color changes according to the function  
mode.  
5. Pressing ENT button 2 returns to the  
This function is not compatible with all cellular  
telephones. Contact your local authorized Clarion  
dealer for information on proper installation and  
compatibility.  
adjustment selection display.  
6. Press ADJ button 4 to return to the previous  
mode.  
DRX8 6 7 5 z  
17  
8. OPERATIONS OF ACCESSORIES  
CD Changer Operations  
CD changer functions  
Selecting a CD  
When an optional CD changer is connected  
through the CeNET cable, this unit controls all  
the CD changer functions.This unit can control a  
total of 2 changers (MD and/or CD).  
Each of the Direct button 9 corresponds to a  
disc loaded into the magazine.  
Selecting a disc from 1 to 6  
Press the corresponding Direct button 9 (1 to  
Press FNC button 3 and select the CD changer  
mode to start play. If 2 CD changers are  
connected, press FNC button 3 to select the  
CD changer for play.  
6)to select the desired disc.  
Selecting a disc from 7 to 12 (only when a  
12 disc CD changer is used.)  
Press and hold the corresponding Direct button  
If NO MAGAZINEappears in the display, insert  
the magazine into the CD changer.DISC CHECK”  
appears in the display while the player loads  
(checks) the magazine.  
If NO DISCappears in the display, eject the  
magazine and insert discs into each slot. Then,  
reinsert the magazine back into the CD changer.  
9
(7 to 12) for 1 second or longer to select the  
desired disc.  
If a CD is not loaded in a slot of the magazine,  
pressing the Direct button 9 corresponding to its  
disc number is invalid.  
Selecting a track  
Track-up  
CAUTION  
1. Press the right side of SEARCH button % to  
CD-ROM discs cannot be played in the CD  
changer.  
move ahead to the beginning of the next track.  
2. Each time you press the right side of SEARCH  
button % , the track advances ahead to the  
beginning of the next track.  
Pausing play  
1. Press Play/pause button 2 to pause play.  
Track-down  
PAUSEappears in the display.  
1. Press the left side of SEARCH button % to  
move back to the beginning of the current  
track.  
2. To resume play, press Play/pause button 2  
again.  
2. Press the left side of SEARCH button % twice  
Displaying CD titles  
This unit can display title data for CD-text CDs  
and user titles input with this unit.  
to move to the beginning of the previous track.  
Fast-forward/fast-backward  
1. Press DISP button ! to display the title.  
Fast-forward  
2. Each time you press and hold DISP button  
Press and hold the right side of SEARCH button  
!
for 1 second or longer, the title display  
% for 1 second or longer.  
changes in the following order:  
Fast-backward  
User title (disc) CD-text title (disc) CD-  
text title (track) user title (disc)...  
Press and hold the left side of SEARCH button  
Note:  
% for 1 second or longer.  
If the CD playing is not a CD-text CD or no user  
title has been input, NO-TTLappears in the  
display.  
Scrolling a CD-text title  
When a CD-text title is longer than 11 characters,  
you can scroll the display as follows.  
1. Display the CD-text title (disc or track).  
2. Press TITLE button 4 . The title scrolls.  
18  
DRX8 6 7 5 z  
CD Changer Operations  
Disc repeat play  
Top function  
The top function plays from the first track (track  
No. 1) of the disc.  
After all the tracks on the current disc have been  
played, the disc repeat play automatically replays  
the current disc over from the first track. This  
function continues automatically until it is  
canceled.  
When playing a disc 1 to 6  
Press the Direct button 9 (1 to 6) with the same  
number as the CD playing.  
1. Press and hold RPT button 6 for 1 second  
or longer.DISCand RPTlight in the display  
and the disc repeat play starts.  
When playing a disc 7 to 12 (only when a  
12 disc CD changer is used.)  
Press and hold for 1 second or longer the Direct  
button 9 (7 to 12) with the same number as the  
CD playing.  
2. To cancel the disc repeat play, press and hold  
RPT button 6 again. DISCand RPTgo  
off from the display and normal play resumes  
on the current track.  
If a CD is not loaded in a slot of the magazine,  
pressing the Direct button 9 corresponding to its  
disc number is invalid.  
Random play  
The random play selects and plays individual  
tracks on the disc in no particular order. This  
function continues automatically until it is  
canceled.  
Scan play  
The scan play locates and plays the first 10  
seconds of each track on a disc automatically.  
This function continues on the disc until it is  
canceled.  
1. Press RDM button 7 . RDMlights in the  
display and the random play begins.  
The scan play is useful when you want to select a  
desired track.  
2. To cancel the random play, press RDM button  
1. Press SCN button 5 to start track scanning.  
7
again.RDMgoes off from the display and  
SCNlights in the display.  
normal play resumes.  
2. To cancel the scan play, press SCN button 5  
again. SCNgoes off from the display and  
the current track continues to play.  
Disc random play  
The disc random play selects and plays individual  
tracks or discs automatically in no particular  
order. This function continues automatically until  
it is canceled.  
Disc scan play  
The disc scan play locates and plays the first 10  
seconds of the first track on each disc in the  
currently selected CD changer. This function  
continues automatically until it is canceled.  
1. Press and hold RDM button 7 for 1 second  
or longer.DISCand RDMlight in the display  
and the disc random play starts.  
The disc scan play is useful when you want to  
2. To cancel the disc random play, press and hold  
RDM button 7 again. DISCand RDMgo  
off from the display and normal play resumes  
from the current track.  
select a desired CD.  
1. Press and hold SCN button 5 for 1 second  
or longer.DISCand SCNlight in the display  
and the disc scan play starts.  
2. To cancel the disc scan play, press SCN button  
5
again. DISCand SCNgo off from the  
display and the current track continues to play.  
Repeat play  
The repeat play continuously plays the current  
track. This function continues automatically until  
it is canceled.  
1. Press RPT button 6 . RPTlights in the  
display and the current track is repeated.  
2. To cancel the repeat play, press RPT button  
6
again. RPTgoes off from the display and  
normal play resumes.  
DRX8 6 7 5 z  
19  
MD Changer Operations  
2. Each time you press the right side of SEARCH  
button % , the track advances ahead to the  
beginning of the next track.  
MD changer functions  
When an optional MD changer is connected  
through the CeNET cable, this unit controls all  
the MD changer functions. This unit can control  
a total of 2 changers (MD and/or CD).  
Track-down  
1. Press the left side of SEARCH button % to  
move back to the beginning of the current track.  
Press FNC button 3 and select the MD changer  
mode to start play. If 2 MD changers are  
connected, press FNC button 3 to select the  
MD changer for play.  
2. Press the left side of SEARCH button % twice  
to move to the beginning of the previous track.  
If NO DISCappears in the display, load MDs  
into the MD changer.  
Fast-forward/fast-backward  
Fast-forward  
Press and hold the right side of SEARCH button  
% for 1 second or longer.  
Pausing play  
1. Press Play/pause button 2 to pause play.  
Fast-backward  
PAUSEappears in the display.  
Press and hold the left side of SEARCH button  
% for 1 second or longer.  
2. To resume play, press Play/pause button 2  
again.  
Top function  
Switching disc titles and track titles  
The top function plays from the first track (track  
No. 1) of the disc. Press the Direct button 9 (1  
to 6) with the same number as the MD playing.  
This unit can display disc titles and track titles  
already entered on MDs. Titles up to 128  
characters long can be displayed by scrolling the  
titles.  
If an MD is not loaded in a slot of the MD changer,  
pressing the Direct button 9 corresponding to its  
disc number is invalid.  
Titles cannot be entered for MDs with this unit.  
1. Press DISP button ! to display the title. The  
disc title or track title is displayed.  
Scan play  
The scan play locates and plays the first 10  
seconds of each track on a disc automatically.This  
function continues on the disc until it is canceled.  
2. Each time you press and hold DISP button  
!
for 1 second or longer, the display toggles  
between the disc title and the track title.  
The scan play is useful when you want to select a  
Scrolling titles  
When a title is longer than 11 characters, you  
can scroll through it with the following operation.  
desired track.  
1. Press SCN button 5 to start track scanning.  
SCNlights in the display.  
1. Display the MD title (disc or track).  
2. Press TITLE button 4 .  
2. To cancel the scan play, press SCN button 5  
again. SCNgoes off from the display and  
the current track continues to play.  
The display scrolls through the title.  
Selecting an MD  
Disc scan play  
Each of the Direct button 9 corresponds to an  
MD loaded into the MD changer. Press the  
corresponding Direct button 9 (1 to 6) to select  
the desired disc.  
The disc scan play locates and plays the first 10  
seconds of the first track on each disc in the  
currently selected MD changer. This function  
continues automatically until it is canceled.  
If an MD is not loaded in a slot of the MD changer,  
pressing the Direct button 9 corresponding to its  
disc number is invalid.  
The disc scan play is useful when you want to  
select a desired MD.  
1. Press and hold SCN button 5 for 1 second  
or longer.DISCand SCNlight in the display  
and the disc scan play starts.  
Selecting a track  
Track-up  
2. To cancel the disc scan play, press and hold  
SCN button 5 again. DISCand SCNgo  
off from the display and the current track  
continues to play.  
1. Press the right side of SEARCH button % to  
move ahead to the beginning of the next track.  
20  
DRX8 6 7 5 z  
MD Changer Operations  
Repeat play  
TV Operations  
TV tuner functions  
The repeat play continuously plays the current  
track. This function continues automatically until  
it is canceled.  
When an optional TV tuner is connected through  
the CeNET cable, this unit controls all TV tuner  
functions. To watch TV requires a TV tuner and  
monitor.  
1. Press RPT button 6 . RPTlights in the  
display and the current track is repeated.  
Watching a TV  
2. To cancel the repeat play, press RPT button  
6
again. RPTgoes off from the display and  
1. Press FNC button 3 and select the TV mode.  
normal play resumes.  
2. Press BND button # to select the desired TV  
band (TV1 or TV2). Each time the button is  
pressed, the input selection toggles between  
TV1 and TV2.  
Disc repeat play  
After all the tracks on the current disc have been  
played, the disc repeat play automatically replays  
the current disc over from the first track. This  
function continues automatically until it is  
canceled.  
3. Press the right or left side of SEARCH button  
% to tune in the desired TV station.  
Watching a video  
1. Press and hold RPT button 6 for 1 second  
or longer.DISCand RPTlight in the display  
and the disc repeat play starts.  
The TV tuner has a VTR input terminal to which  
1 external device can be connected. Connect a  
12V video cassette player (VCP) or video  
cassette recorder (VCR) to the TV tuner input  
terminal.  
2. To cancel the disc repeat play, press and hold  
RPT button 6 again. DISCand RPTgo  
off from the display and normal play resumes  
on the current track.  
1. Press RDM button 7 to select VTR.  
2. To return to the TV broadcast, press RDM  
button 7 .  
Random play  
The random play selects and plays individual  
tracks on the disc in no particular order. This  
function continues automatically until it is  
canceled.  
Tuning  
There are 3 types of tuning mode available, Seek  
tuning, manual tuning and preset tuning.  
1. Press RDM button 7 . RDMlights in the  
Seek tuning  
1. Press BND button # and select the desired  
display and the random play begins.  
2. To cancel the random play, press RDM button  
TV band (TV1 or TV2).  
7
again.RDMgoes off from the display and  
If MANUis lit in the display, press and hold  
BND button # for 1 second or longer. MANU”  
in the display goes off and seek tuning is now  
available.  
normal play resumes.  
Disc random play  
2. Press the right or left side of SEARCH button  
The disc random play selects and plays individual  
tracks or discs automatically in no particular  
order.This function continues automatically until  
it is canceled.  
% to automatically seek a station.  
Press the right side of SEARCH button % to  
automatically tune up the frequency band to  
the next available TV station; press the left  
side to automatically tune down.  
1. Press and hold RDM button 7 for 1 second  
or longer.DISCand RDMlight in the display  
and the disc random play starts.  
2. To cancel the disc random play, press and hold  
RDM button 7 again. DISCand RDMgo  
off from the display and normal play resumes  
from the current track.  
DRX8 6 7 5 z  
21  
TV Operations  
Manual tuning  
There are 2 ways available:Quick tuning and step  
tuning.  
only the strong stations are stored into memory.  
1. Press BND button # and select the desired  
TV band (TV1 or TV2).  
2. Press and hold AS button 5 for 2 seconds or  
longer. The stations with good reception are  
automatically stored to the Preset buttons 9 .  
When you are in the step tuning mode, the  
frequency changes one step at a time. In quick  
tuning mode, you can quickly tune the desired  
frequency.  
Preset scan  
1. Press BND button # and select the desired  
band (TV1 or TV2).  
Preset scan allows the user to view each preset  
position before it automatically advances to the  
next preset. This function is useful for searching  
for desired TV station in memory.  
If MANUis not lit in the display, press and  
hold BND button # for 1 second or longer.  
MANUis lights in the display and manual  
tuning is now available.  
1. Press PS button 5 .  
2. Tune into a station.  
2. When the desired station is found, press PS  
Quick tuning:  
button 5 again to remain tuned to that station.  
Press and hold the right or left side of  
SEARCH button % for 1 second or longer to  
tune in a station.  
Note:  
Do not press and hold PS button 5 for 2 seconds  
or longer. Doing so will trigger the auto store  
function and start storing stations into memory.  
Step tuning:  
Press the right or left side of SEARCH button  
% to manually tune in a station.  
Setting the TV diver  
You can change the reception setting for the TV  
antenna connected to the TV tuner.  
Recalling a preset station  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection  
display.  
A total of 12 TV stations can be stored (6-TV1  
and 6-TV2).This allows you to select your favorite  
TV stations and store them in memory for later  
recall.  
2. Press the right or left side of SEARCH button  
% to select TV DIVER.  
1. Press BND button # and select the desired  
TV band (TV1 or TV2).  
3. Press ENT button 2 .  
2. To recall a storedTV station, press the desired  
4. Turn the Rotary knob & clockwise to set to  
Preset button 9 to select that station.  
ONor counterclockwise to set to OFF.  
Press and hold one of the Preset buttons 9  
for 2 seconds or longer to store the current  
station into the preset memory.  
ON:  
Sets reception emphasizing the visual.  
OFF:  
Sets the diver setting to OFF.  
5. Press ENT button 2 .  
Manual memory  
1. Select the desired station with seek tuning,  
manual tuning or preset tuning.  
6. Press ADJ button 4 to return to the previous  
mode.  
2. Press and hold one of the Preset buttons 9  
for 2 seconds or longer to store the current  
station to that preset memory.  
Auto store  
Auto store selects 6TV stations automatically and  
stores each one into a preset memory.  
If there are not 6 stations with good reception,  
stations previously stored in memory remain and  
22  
DRX8 6 7 5 z  
DSP Operations  
DSP control function  
4. Turn the Rotary knob & clockwise or  
counterclockwise to set the sensitivity of the  
spectrum analyzer.  
If the DSP (DPH7500z), sold separately, is  
connected to this unit using the CeNET cable,  
all the functions of the DSP can be controlled.  
You can choose one of LOW, MID-LOW,  
MID, MID-HIGHor HIGHfor the  
sensitivity of the spectrum analyzer.  
DSP functions  
5. Pressing ENT button 2 returns to the  
There are 2 modes available in DPH7500z, easy  
mode and professional mode. Choose one of  
them and adjust the sound field and the sound  
quality.  
adjustment selection display.  
6. Press ADJ button 4 to return to the previous  
mode.  
• Functions common to each mode:  
Spectrum analyzer display, auto loudness, etc.  
• Easy mode:  
Output adjustment of auto loudness,  
subwoofer and playback band  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection  
display.  
Adjustment using the graphic equalizer function  
and the DSP function.  
• Professional mode:  
2. Press the right or left side of SEARCH button  
Adjustment using the space equalizer function  
and the parametric equalizer function.  
% to select SOUND.  
3. Press ENT button 2 .  
When the easy mode is selected, adjustment for  
the professional mode cannot be made. On the  
contrary, when the professional mode is selected,  
adjustment for the easy mode cannot be made.  
For details on functions of each mode, refer to  
the owner’s manual supplied with the  
DPH7500z.  
Hereafter the graphic equalizer is referred to as a  
G.EQ., the space equalizer referred to as S.EQ.  
and the parametric equalizer referred to as P.EQ.  
4. Press the right or left side of SEARCH button  
% to select the adjustment item.  
There are A.LD LEVEL, WOOFER OUT,  
WOOFER LPF, HPFand TEST TONE”  
available for the adjustment items.  
For details on each adjustment item, refer to the  
owners manual supplied with the DPH7500z.  
5. Turn the Rotary knob & clockwise or  
counterclockwise to make the adjustment.  
Operations common to each mode  
Enjoying a spectrum analyzer  
This unit can display the spectrum analyzer.  
There are 8 spectrum analyzer patterns.  
6. Pressing ENT button 2 returns to the  
adjustment selection display.  
7. Press ADJ button 4 to return to the previous  
mode.  
1. Press DISP button ! to select the spectrum  
Selecting easy mode or professional  
mode  
The factory default setting is EASY.  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection  
display.  
analyzer display.  
2. Each time you press and hold DISP button  
!
for 1 second or longer, the spectrum  
analyzer patterns are switched.  
Setting the sensitivity of the  
spectrum analyzer  
2. Press the right or left side of SEARCH button  
% to select DSP/EQ SEL.  
The factory default setting is MID.  
1. Press and hold ADJ button 4 for 1 second or  
longer to switch to the adjustment selection  
display.  
3. Press ENT button 2 .  
4. Turn the Rotary knob & clockwise or  
counterclockwise to set the mode to EASY”  
or PRO.  
2. Press the right or left side of SEARCH button  
5. Pressing ENT button 2 returns to the  
% to select ANA SENS.  
adjustment selection display.  
3. Press ENT button 2 .  
6. Press ADJ button 4 to return to the previous  
mode.  
DRX8 6 7 5 z  
23  
DSP Operations  
Inputting a title  
Selecting a G.EQ menu  
You can give a title to the user memory of the  
DSP, G.EQ, S.EQ and P.EQ that you have  
adjusted yourself.  
1. Press A-M button $ and select G.EQ.  
G.EQblinks in the display.  
2. Press BND button # to select BASC(basic).  
BASCappears in the function mode  
indication # .  
1. Press A-M button $ to select the adjustment  
mode in which you want to give a title.  
2. Press BND button # to select USER.  
USERappears in the function mode  
indication # .  
3. Press one of the Direct buttons 9 and select  
the desired G.EQ menu.  
To select the user memory, press BND button  
#
to select USERand press one of the Direct  
3. Press one of the Preset buttons 9 to select  
the user memory to which you want to give a  
title.  
buttons 9 .  
Editing/storing a G.EQ menu (User  
memory)  
1. Select a G.EQ menu which you want to edit  
on the basis of.  
4. Press TITLE button 4 .  
5. Press the right or left side of SEARCH button  
% to move the cursor.  
6. Press DISP button ! to select a character.  
2. Press and hold ADJ button 4 for 1 second or  
There are capital letters, small letters,  
numbers, symbols and umlaut available for  
the character.  
longer.  
3. Press the right or left side of SEARCH button  
% to select the frequency to be adjusted.  
There are 50Hz, 100Hz, 200Hz, 400Hz, 1kHz,  
3kHz and 12kHz available for the adjustment  
frequency.  
7. Turn the Rotary knob & clockwise or  
counterclockwise to select the character you  
want to input.  
8. Repeat steps 5 to 7 to input the title.  
For details on each adjustment item, refer to the  
owners manual supplied with the DPH7500z.  
9. Press and hold ENT button 2 for 2 seconds  
or longer to put the title into memory.The title  
input mode is canceled.  
4. Turn the Rotary knob & clockwise or  
counterclockwise to make the adjustment.The  
adjustment range is from 12dB to +12dB.  
Easy mode/G.EQ operations  
5. Repeat steps 3 to 4 to complete the  
adjustment and press ADJ button 4 .  
Note:  
6. Press and hold one of the Direct buttons 9  
for 2 seconds or longer to store the edited  
contents.  
The adjustment made in easy mode is not reflected  
in the adjustment in professional mode. On the  
contrary, the adjustment made in professional  
mode is not reflected in the adjustment in easy  
mode.  
You can give a title to the user memory. For the  
inputting method of titles, refer to the subsection  
Inputting a titlein the Operations common  
to each mode.  
G.EQ effect on/off  
While the G.EQindication 4 is lit in the display,  
the G.EQ effect is set to ON.  
Easy mode/DSP operations  
The factory default setting is ON.  
DSP effect on/off  
When the DSPindication 5 is lit in the display,  
the DSP effect is set to ON.  
1
Press A-M button $ and select G.EQ.While  
G.EQis selected, G.EQblinks in the  
display.  
The factory default setting is ON.  
1. Press A-M button $ and select DSP. While  
2. Press DISP button ! .  
3. Press A-M button $ . G.EQin the display is  
DSPis selected, DSPblinks in the display.  
changed from blinking to lit or unlit.  
2. Press DISP button ! .  
When G.EQis unlit, the G.EQ effect is set to  
OFF.  
Note:  
3. Press A-M button $ . DSPin the display is  
changed from blinking to lit or unlit.  
When DSPis unlit, the DSP effect is set to OFF.  
If the G.EQ effect is set to OFF, the adjustment  
made in the G.EQ operationsis not reflected in  
the music source.  
24  
DRX8 6 7 5 z  
DSP Operations  
Note:  
and HIGH or LIVENESS available for the items  
to be adjusted.  
If the DSP effect is set to OFF, the adjustment  
made in the DSP operationsis not reflected in  
the music source.  
For details on each adjustment item, refer to the  
owners manual supplied with the DPH7500z.  
4. Turn the Rotary knob & clockwise or  
Setting a listening position menu  
counterclockwise to make the adjustment.  
1. Press A-M button $ and select DSP. DSP”  
5. Repeat steps 3 to 4 to complete the  
blinks in the display.  
adjustment and press ADJ button 4 .  
2. Press the right or left side of SEARCH button  
6. Press and hold one of the Direct buttons 9  
for 2 seconds or longer to store the edited  
contents.  
% to set the listening position type.  
There are FULL SEAT, FRONT-RIGHT (only  
right seat), FRONT-LEFT (only left seat),  
FRONT (only front seats), REAR (only rear  
seats) and PASS available for the listening  
position types.  
You can give a title to the user memory. For  
the inputting method of titles, refer to the  
subsection Inputting  
a
titlein the  
Operations common to each mode.  
The factory default setting is FULL SEAT.  
Professional mode/S.EQ operations  
Making fine adjustment of the  
listening position  
1. Upon completion of setting the listening  
Note:  
The adjustment made in professional mode is not  
reflected in the adjustment in easy mode. On the  
contrary, the adjustment made in easy mode is  
not reflected in the adjustment in professional  
mode.  
position, press ENT button 2 .  
2. Press the right or left side of SEARCH button  
% to select BALor FAD.The selected item  
blinks.  
S.EQ effect on/off  
While the S.EQindication 8 is lit in the display,  
the S.EQ effect is set to ON.  
3. Turn the Rotary knob & clockwise or  
counterclockwise to adjust the balance and  
the fader.  
The factory default setting is ON.  
1. Press A-M button $ and select S.EQ.While  
S.EQis selected, S.EQblinks in the  
display.  
4. Press ENT button 2 to return to the DSP  
mode.  
Selecting a sound field menu  
1. Press A-M button $ and select DSP. DSP”  
2. Press DISP button ! .  
3. Press A-M button $ . S.EQin the display is  
blinks in the display.  
changed from blinking to lit or unlit.  
2. Press BND button # to select B-1(basic-1)  
or B-2(basic-2). B-1or B-2appears in  
the function mode indication # .  
When S.EQis unlit, the S.EQ effect is set to  
OFF.  
Note:  
3. Press one of the Direct buttons 9 and select  
If the S.EQ effect is set to OFF, the adjustment  
made in the S.EQ operationsis not reflected in  
the music source.  
the desired sound field menu.  
To select the user memory, press BND button  
#
to select USERand press one of the Direct  
buttons 9 .  
Selecting a S.EQ menu  
1. Press A-M button $ and select S.EQ.  
Editing/storing a sound field menu  
S.EQblinks in the display.  
1. Select a sound field menu which you want to  
edit on the basis of.  
2. Press BND button # to select BASC(basic).  
BASCappears in the function mode  
indication # .  
2. Press and hold ADJ button 4 for 1 second or  
longer.  
3. Press one of the Direct buttons 9 and select  
the desired S.EQ menu.  
3. Press the right or left side of SEARCH button  
% to select the item to be adjusted.  
To select the user memory, press BND button  
#
to select USERand press one of the Direct  
There are EFFECT LEVEL, INITIAL DELAY,  
REAR MIX, REVERB TIME or ROOM SIZE  
buttons 9 .  
DRX8 6 7 5 z  
25  
DSP Operations  
Editing/storing a S.EQ menu (User  
memory)  
Selecting a P.EQ menu  
1. Press A-M button $ and select P.EQ. P.EQ”  
blinks in the display.  
1. Select a S.EQ menu which you want to edit  
on the basis of.  
2. Press BND button # to select BASC(basic).  
BASCappears in the function mode  
indication # .  
2. Press and hold ADJ button 4 for 1 second or  
longer.  
3. Press one of the Direct buttons 9 and select  
3. Press the right or left side of SEARCH button  
the desired P.EQ menu.  
% to select the item to be adjusted.  
To select the user memory, press BND button  
There are DIFFUZE, CAR WIDTH and CAR  
LENGTH available for the items to be adjusted.  
#
to select USERand press one of the Direct  
buttons 9 .  
For details on each adjustment item, refer to the  
owners manual supplied with the DPH7500z.  
Editing/storing a P.EQ menu (User  
memory)  
1. Select a P.EQ menu which you want to edit  
on the basis of.  
4. Turn the Rotary knob & clockwise or  
counterclockwise to make the adjustment.The  
adjustment range is from 1 to 10 for each item.  
5. Repeat steps 3 to 4 to complete the  
2. Press and hold ADJ button 4 for 1 second or  
adjustment and press ADJ button 4 .  
longer.  
6. Press and hold one of the Direct buttons 9  
for 2 seconds or longer to store the edited  
contents.  
3. Press the right or left side of SEARCH button  
% to select the item to be adjusted.  
There are correction channel, correction band,  
selection of the center frequency, gain  
adjustment and selection of the Q-curve  
available for the items to be adjusted.  
You can give a title to the user memory. For  
the inputting method of titles, refer to the  
subsection Inputting  
a
titlein the  
Operations common to each mode.  
For details on each adjustment item, refer to the  
owners manual supplied with the DPH7500z.  
Professional mode/P.EQ operations  
4. Turn the Rotary knob & clockwise or  
P.EQ effect on/off  
While the P.EQindication 7 is lit in the display,  
the P.EQ effect is set to ON.  
counterclockwise to make the adjustment.  
5. Repeat steps 3 to 4 to complete the  
adjustment and press ADJ button 4 .  
The factory default setting is ON.  
1. Press A-M button $ and select P.EQ.While  
P.EQis selected, P.EQblinks in the display.  
6. Press and hold one of the Direct buttons 9  
for 2 seconds or longer to store the edited  
contents.  
2. Press DISP button ! .  
You can give a title to the user memory. For  
the inputting method of titles, refer to the  
3. Press A-M button $ . P.EQin the display is  
changed from blinking to lit or unlit.  
subsection Inputting  
Operations common to each mode.  
a
titlein the  
When P.EQis unlit, the P.EQ effect is set to OFF.  
Note:  
If the P.EQ effect is set to OFF, the adjustment  
made in the P.EQ operationsis not reflected in  
the music source.  
26  
DRX8 6 7 5 z  
9. TROUBLESHOOTING  
Problem  
Cause  
Measure  
Power does not  
turn on.  
Fuse is blown.  
Replace with a fuse of the same amperage. If the  
fuse blows again, consult your store of purchase.  
(No sound is  
produced.)  
Incorrect wiring.  
Consult your store of purchase.  
No sound output Power antenna lead is  
1. Turn the unit off.  
when operating  
the unit with  
amplifiers or  
power antenna  
attached.  
shorted to ground or  
2. Remove all wires attached to the power antenna  
lead. Check each wire for a possible short to  
ground using an ohm meter.  
excessive current is required  
for remote-on the amplifiers  
or power antenna.  
3. Turn the unit back on.  
4. Reconnect each amplifier remote wire to the  
power antenna lead one by one. If the amplifiers  
turn off before all wires are attached, use an  
external relay to provide remote-on voltage  
(excessive current required).  
Nothing happens The microprocessor has  
when buttons are malfunctioned due to noise,  
Turn off the power, then press the OPEN button 1  
and remove the DCP.  
Press the reset button for about 2 seconds with a thin  
pressed.  
etc.  
rod.  
Reset button  
Display is not  
accurate.  
DCP or source unit  
connectors are dirty.  
Wipe the dirt off with a soft cloth moistened with  
cleaning alcohol.  
Compact disc  
Another compact disc is  
Eject the compact disc before loading the new one.  
cannot be loaded. already loaded.  
Sound skips or is Compact disc is dirty.  
noisy.  
Clean the compact disc with a soft cloth.  
Compact disc is heavily  
scratched or warped.  
Replace with a compact disc with no scratches.  
Sound is bad  
directly after  
power is turned  
on.  
Water droplets may form on  
the internal lens when the  
car is parked in a humid  
place.  
Let dry for about 1 hour with the power on.  
DRX8 6 7 5 z  
27  
10. ERROR DISPLAYS  
If an error occurs, one of the following displays is displayed.  
Take the measures described below to eliminate the problem.  
Cause  
Error Display  
ERROR 2  
Measure  
A CD is caught inside the CD deck and is  
not ejected.  
This is a failure of CD decks mechanism  
and consult your store of purchase.  
ERROR 3  
ERROR 6  
ERROR 2  
ERROR 3  
ERROR 6  
ERROR H  
A CD cannot be played due to scratches,  
etc.  
Replace with a non-scratched,  
non-warped-disc.  
A CD is loaded upside-down inside the CD Eject the disc then reload it properly.  
deck and does not play.  
A CD inside the CD changer is not loaded. This is a failure of CD changers mecha-  
nism and consult your store of purchase.  
A CD inside the CD changer cannot be  
played due to scratches, etc.  
Replace with a non-scratched, non-warped  
disc.  
A CD inside the CD changer cannot be  
played because it is loaded upside-down.  
Eject the disc then reload it properly.  
Displayed when the temperature in the  
MD changer is too high and playback has  
been stopped automatically.  
Lower the surrounding temperature and  
wait for a while to cool off MD changer.  
ERROR 2  
ERROR 3  
ERROR 6  
An MD inside the MD changer is not  
loaded.  
This is a failure of MD changers mecha-  
nism and consult your store of purchase.  
An MD inside the MD changer cannot be  
played due to scratches, etc.  
Replace with a non-scratched, non-warped  
disc.  
An MD inside the MD changer cannot be  
played because it is loaded upside-down.  
Eject the disc then reload it properly.  
Displayed when a non-recorded MD is  
loaded in the MD changer.  
Load a pre-recorded MD in the MD  
changer.  
If an error display other than the ones described above appears, press the reset button. If the problem  
persists, turn off the power and consult your store of purchase.  
28  
DRX8 6 7 5 z  
11. SPECIFICATIONS  
FM Tuner  
Frequency Range:  
87.9 MHz to 107.9 MHz  
Audio  
Maximum Power Output:  
180 W (45 W × 4 ch) (EIAJ)  
Usable Sensitivity:  
11 dBf  
Continuous Average Power Output:  
17 W × 4, into 4 , 20 Hz to 20 kHz, 1%THD  
50dB Quieting Sensitivity:  
17 dBf  
Bass Control Action (30 Hz):  
±15 dB  
Alternate Channel Selectivity:  
75 dB  
Treble Control Action (10 kHz):  
±10 dB  
Stereo Separation (1 kHz):  
35 dB  
Line Output Level (CD 1 kHz):  
4 V  
Frequency Response (±3 dB):  
30 Hz to 15 kHz  
General  
Power Supply Voltage:  
14.4 V DC (10.8 to 15.6 V allowable),  
negative ground  
AM Tuner  
Frequency Range:  
530 kHz to 1710 kHz  
Current Consumption:  
Less than 15 A  
Usable Sensitivity:  
25 µV  
Speaker Impedance:  
4 (4 to 8 allowable)  
Weight / Source unit:  
3.75 lb. (1.7 kg)  
CD Player  
System:  
Compact disc digital audio system  
Weight / Remote control unit:  
1 oz. (30 g) (including battery)  
Usable Discs:  
Compact disc  
Dimensions / Source unit:  
7" (Width) × 2" (Height) × 6-1/8" (Depth)  
[178 (W) × 50 (H) × 155 (D) mm]  
Frequency Response (±1 dB):  
5 Hz to 20 kHz  
Dimensions / Remote control unit:  
1-3/4" (Width) × 4-5/16" (Height) × 1-1/8" (Depth)  
[44 (W) × 110 (H) × 27 (D) mm]  
Signal to Noise Ratio (1 kHz):  
100 dB  
Dynamic Range (1 kHz):  
95 dB  
Harmonic Distortion:  
0.01%  
Notes:  
Specifications comply with EIA Standards.  
Specifications and design are subject to change without notice for further improvement.  
DRX8 6 7 5 z  
29  
Memo  
30  
DRX8 6 7 5 z  

Motorola Stature i9 User Manual
Motorola MOTO WX395 User Manual
Maxtor Personal Storage 3000XTX01FWRA160 User Manual
Lindy 70674 User Manual
LG Electronics VENUS User Manual
Hitachi Travelstar HTS727550A9E364 User Manual
FARGO electronic CUPS HDP5000 User Manual
Denon DN D4500 User Manual
Butler 645 061 User Manual
Antec Quiet Computing 0761345 02220 0 User Manual