|
Addonics
T E C H N O L O G I E S
Jupiter Cipher Combo Hard Drive
For the following models:
JCCHDIU64, JCCHDIF64, JCCHDIS64
JCCHDIU128, JCCHDIF128, JCCHDIS128
User’s Guide
Version 1.0
Contents
FCC Warning...................................................................................1
Limited Warranty............................................................................ 1
Contents............................................................................................ 2
Chapter 1 General Information .........................................................3
Features............................................................................ 3
Jupiter Cipher Combo Hard Drive models ........................ 4
Chapter 2 Jupiter Cipher Combo Hard Drive key.............................. 5
Chapter 3 Keeping track of the hard drive.........................................6
Chapter 4 Jumper Setting for Jupiter Cipher Combo Hard Drive.......7
Chapter 5 Hardware Installation Guide ........................................8-10
Jupiter Combo Hard Drive ........................................ 11-13
Optional Hardware ...................................................14-15
Chapter 6 Attaching USIB Interface Cable ..................................... 16
Chapter 7 USB2.0 USIB Interface Cable Driver Installation ...... 17-18
Serial ATA USIB Interface Cable Driver Installation .... 19
Firewire USIB Interface Cable Driver Installation ......... 20
How to use Disk Management ...................................21-22
Technical Support & Contact Information................................ …23
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 2
Chapter 1
General Information
The Addonics Technologies Jupiter Cipher Combo Hard Drive is a portable
2.5” Hard Disk Drive kit. It consists of the Jupiter Cipher ExDrive and IDE
drive cradle.
Features
·
·
·
·
·
·
·
Stylished and rugged black anodized aluminum housing
Compact size and light weight
Shock proof - up to 3 feet drop damage protection for the hard drive
Easy hard drive installation
Choice of standard or encryption drive enclosure
The most versatile hard drive kit in the market
Connect as an External Hard drive to any computer via USB2.0, CardBus,
Firewire/iLink and Serial ATA port (only one of these cables is included in
Turn any 2.5” hard drives into external hard drive or removable hard drive
Use as a removable Hard Drive on Desktops PC
·
·
·
Plug & Play Operation under Windows 98SE, Me, 2000, XP and 2003
Server
·
Portable: Enclosure fits any Briefcase or Notebook PC Case.
Encryption
·
·
Hardware based 64-bit DES or 128-bit TDES full disk encryption
High performance - Data is encrypted and decrypted on the fly by a
certified cryptographic engine inside an ASIC without taking any CPU
resources
·
·
·
Encryption / Decryption via a hardware key, just like using a regular key to
open a door.
Simple to deploy with no training required, no software to install and no
password to remember
Platform independency - There is no software or driver to install to use
Addonics encryption products. As a result, it can be deployed in any
systems running any OS. This is important in organization with multi
platform computing and legacy systems.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 3
Jupiter Cipher Combo Hard Drive
Item Number Product Description
JCCHDIU64
JCCHDIF64
JCCHDIS64
Jupiter Cipher 64-bit Combo Hard Drive USB 2.0 for 2.5”
IDE hard drive
Jupiter Cipher 64-bit Combo Hard Drive Firewire/iLink for
2.5” IDE hard drive
Jupiter Cipher 64-bit Combo Hard Drive SATA for 2.5”
IDE hard drive
JCCHDIU128 Jupiter Cipher 128-bit Combo Hard Drive USB 2.0 for 2.5”
IDE hard drive
JCCHDIF128 Jupiter Cipher 128-bit Combo Hard Drive Firewire/iLink
for 2.5” IDE hard drive
JCCHDIS128 Jupiter Cipher 128-bit Combo Hard Drive SATA for 2.5”
IDE hard drive
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 4
Chapter 2
Jupiter Cipher Combo Hard Drive key
Check to make sure you have the correct version of Jupiter Cipher Combo Hard
Drive key. The key should match the label at the bottom of the drive enclosure.
Yellow label DES-64
Green label TDES-128
stands for Jupiter Cipher
stands for Jupiter Cipher
Combo Hard Drive 64-bit
Combo Hard Drive 128-bit
key
key
IMPORTANT
There is no back door for the Jupiter Cipher Combo Hard Drive encrypted
hard drive if the key is lost or stolen.
To ensure that there is a spare key, your Jupiter Cipher Combo Hard Drive
bundled kit comes with one pair of Jupiter Cipher Combo Hard Drive keys.
These 2 keys have identical encryption code. One of these keys should be kept
in a safe and secure location and can be sent back to Addonics for duplicating
additional keys. If you are down to the last key, be sure to make a back up of all
the data stored inside your encrypted hard drive prior to sending the last key to
Addonics. Addonics is not responsible for key lost in the mail or retrieval of the
data inside the encrypted hard drive.
Ø
Ø
Ø
The CIPHER key MUST be inserted at the front of the drive enclosure
in order for the drive to be ACTIVATED.
Once the drive is INITIALIZED using the Cipher Key that comes with
the kit, the drive can only be accessed by the original key.
The 2 keys that come with each Jupiter Cipher Combo Hard Drive
bundled kit has their own unique encryption code. So the keys among
different kits are not interchangeable.
If you have multiple sets of Jupiter Cipher Combo Hard Drive kits and would
like all the keys to have the same encryption code, you may make this request at
the time of your order or mail the keys together with master key back to
Addonics to recode them for you. Again be sure that you keep a spare key with
you. Make a back up of your data if you are mailing in your last key.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 5
Chapter 3
Keeping track of the hard drive
If you are using the Jupiter Cipher Combo Hard Drive enclosure to encrypt
multiple hard drives, it is important to label your hard drive if you are taking
the drive out of the enclosure. The hard drive with Jupiter Cipher Combo Hard
Drive encryption will look like a brand new drive when attach directly to the
IDE or SATA controller of a computer. There will be no partition or any hint to
indicate that the drive contains encrypted data. When the drive is partitioned,
all the encrypted data will be lost.
The same holds true if a hard drive already has data on it is installed into the
Jupiter Cipher Combo Hard Drive enclosure. The computer detects the hard
drive as a brand new drive or a drive that is unallocated. Once you proceed to
partition the drive, the data that was on the hard drive will be erased and
cannot be recovered.
A Jupiter Cipher Combo Hard Drive encrypted hard drive can be moved to
another Jupiter Cipher Combo Hard Drive enclosure. But the same key used in
encrypting the hard drive must be used in the new drive enclosure in order to
access the drive.
If you are installing multiple Jupiter Cipher Combo Hard Drive kits into a
large organization, it is important to keep track of the drive and the
encryption key. Once it gets mixed up, there is no possible way to recover
the data on the encrypted hard drive.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 6
Chapter 4
Jumper Settings Inside the Jupiter Cipher Combo Hard Drive
Settings when Jupiter ExDrive is used as an External Enclosure
1. If the Jupiter ExDrive will be used externally with the external AC adapter,
the switch from the case must be switch to the right, labeled EXT to grab
power from external power supply.
Application: Jupiter ExDrive can be set to receive power EXT and be used
with all three types of USIB cables: USB2.0 USIB, Firewire USIB & SATA
USIB
2. If the Jupiter ExDrive will be used externally without the external AC
adapter, the switch from the case must be switch to the left, labeled INT to
grab power from system.
Application: Jupiter ExDrive can be set to receive power INT and be used with
the following types of USIB cables: USB2.0 USIB & Firewire USIB
Note: We recommend setting the hard drive to MASTER mode/setting at all
times. (Default setting)
J4 Pin Definition for Master Setting
Hard Drive Brand
Hitachi
J4 Jumper Setting
Pin 1~6 Open
NEC
Fujitsu
Toshiba
Seagate
J1 Pin Definition for USIB Interface
Hard Drive Setting J1 Jumper Setting
Master
Pin 3 - Pin 5 Short
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 7
Chapter 5
Hardware Installation Guide
Exploded View of Enclosure shown with various components
top cover
2.5” hard drive
shock
absorbers
switch
PCB
bottom cover
screw
cipher slot
Step 1
Separate the top from the bottom cover
of the drive enclosure by loosening the
screw as shown on the photo.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 8
Step 2
Align the male IDE connector on the
2.5” hard drive with the female IDE
connector on the PCB. Push the hard
drive till the connector pins on the hard
drive is fully seated inside the
connector on the PCB.
Step 3
Wrap the shock absorber around the
hard drive and PCB.
Step 4
Turn over the PCB and secure the
hard drive to the PCB with the
mounting screws that come with the
kit.
Step 5
Mount the board to the bottom cover.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 9
Step 6
Put the top cover on by holding it in near
vertical position and sliding the two
metal clips inside the two small slots on
the rear of the bottom cover.
Step 7
Lower the front of the top cover and
making sure the two covers lined up
properly. Tighten the small retaining
screw on the front of the bottom cover
to close the enclosure.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 10
Jupiter Cipher Combo Hard Drive
Note: Combo hard drive is the combination of Jupiter Cipher ExDrive kit and
the IDE drive cradle.
Allows a 2.5” Jupiter Cipher ExDrive to be used as an external hard drive and
also be plug-in to a desktop computer internally. You may use an available 3.5”
Floppy bay like the image shown below to install the Jupiter Cipher ExDrive
cradle. If none is available you can mount one to a 5.25 bay with mounting
brackets to fit the bay.
Jupiter Cipher ExDrive is used as External Enclosure
USIB Interface
Cable
Jupiter Cipher
ExDrive
External power
input jack (for
Note: Use the jumper settings in chapter 4 for the above configuration
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 11
Jupiter Cipher ExDrive is used as an Internal Enclosure
40 Pin IDE
Connector
Power Socket
MC-36 Pin
Connector
Note: Use the jumper settings on the next page for the above configuration
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 12
Configuration:
Jupiter Cipher ExDrive enclosure is placed inside IDE drive cardle. IDE
drive cradle is connected to the IDE Controller on the mainboard with an
IDE cable.
A. Jupiter Cipher ExDrive is set to MASTER
Hard Drive
Brand
J4 Jumper Setting
Hitachi
NEC
Pin 1~6 Open
Fujitsu
Toshiba
Seagate
Hard Drive
Setting
J1 Jumper Setting
Master
Pin 1 – Pin 3 Short
Pin 2 – Pin 4 Short
Since the Jupiter Mobile Rack will be used internally without external AC
adapter, the switch from the case must be switch to the left, labeled INT to grab
power from system.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 13
Optional Hardware
A.
SATA Cartridge Cradle System
4-pin Molex
power connector
for PC power
2-pin connector on the
IDE to SATA converter
board
2-pin connector on
the PCB board
IDE to SATA
converter
SATA connector
For Win98SE, Me, 2000 and XP
Note: There are no drivers needed to use the Serial ATA cable as long as the
drivers are installed for the Serial ATA Controller card/chip. It is plug and
play.
Hot Swap using Serial ATA connection is supported only on host controller
using Silicon Image chipset.
Disk Management for Windows 98
Note: Refer to the SATARAID Management Utility Manual
SATARAID Manual V1.30 (for non-RAID5 Controllers) found in the
Addonics Technologies website
B.
USB 2.0/1.1 Cartridge Cradle System
4-pin Molex
power connector
for PC power
2-pin connector on the
IDE to USB converter
board
2-pin connector on
the PCB board
IDE to USB2.0
converter
USB connector
Note: The Hot Swap feature for the above configurations is enabled by the
connection of the power cable connected to the 2-pin connector on the PCB
board on the cradle and the 2-pin connector on the IDE to SATA or IDE to
USB converter boards. With this feature you can remove the Jupiter Cipher
ExDrive from the cradle without shutting down the system.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 14
Jumper Settings for Internal Cartridge Cradle System
Jupiter Cipher ExDrive is set to MASTER
Hard Drive
Brand
J4 Jumper
Setting
Hitachi
NEC
Pin 1~6 Open
Fujitsu
Toshiba
Seagate
Hard Drive
Setting
J1 Jumper
Setting
Master
Pin 1 – Pin 3 Short
Pin 2 – Pin 4 Short
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 15
Chapter 6
Attaching USIB interface cable
USIB connector for
use with the
Addonics USIB
interface cable
External power input
jack (for use as external
hard drive)
Addonics USIB
interface cable
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 16
Chapter 7
7.1
USB2.0 USIB Cable (Model: AAUSBC-309)
Note: USB Jupiter ExDrive is Plug and Play under Windows XP, 2000 and
98Me. There is no third party driver needed.
·
·
Since USB 2.0 Hi-Speed is an evolution of the existing USB 1.1
specification, it is fully forward and backward compatible with current
USB systems.
If you do not have an USB2.0 port, you may install an optional USB2.0
adapter or controller
Driver Installation for Win98 and Win98SE
Downloading the USB2.0 USIB Cable Driver from the Addonics Driver
Disk
1. Insert the Addonics Driver Disk in the CDROM drive. The Addonics
Driver Disk window opens.
2. Select Drivers > Interface Cables Drivers > USB2.0 Cable (AAUSBC-309)
Win98/98SE Only.
3. The Winzip Self-Extractor –AT2LP.exe window opens. Unzip file in My
Documents.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 17
Driver Installation for Win98 and Win98SE
1. Make sure your computer is up and running.
2. Insert the USB2.0 USIB cable to the USB Port.
3. A "New Hardware Found" message shall pop up, click Next.
4. “What do you want Windows to do?” message opens. Select “Search for
the best driver for your device,” click Next.
5. “Specify Location” message opens. Point to the location of
C:\mass_storage_601where you unzip the files for the driver. Click Next.
6. “Driver file search for the device %VID_ODBF&PID_0303%” then
Building a driver database message opens. Let Windows finish the
installation and click Finish.
Disk Management for Windows 98
1. Select Start > Setting > Control Panel > System. The System Properties
window opens.
2. Select the Device Manager tab, under Device type, Disk Drives, select your
new hard drive. Click the Properties button.
3. Select the Settings tab and under the Options box, click the Removable
check box. The Reserved drive letters box becomes active. Select the drive
letter for your new drive. Click Ok.
4. Click Yes to restart your system to make changes take effect.
5. Double click My Computer icon and there should be an extra drive letter
for the Jupiter ExDrive drive. You may now access the drive.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 18
7.2
SATA USIB Cable (Model: AASAC-605)
For Win98SE, Me, 2000 and XP
Note: There no drivers needed to use the Serial ATA cable as long as the
drivers are installed for the Serial ATA Controller card/chip. It is plug and
play.
Disk Management for Windows 98
Note: Refer to the SATARAID Management Utility Manual
SATARAID Manual V1.30 (for non-RAID5 Controllers) found in the
Addonics Technologies website
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 19
7.3
FIREWIRE USIB Cable (Model: AAFWC-406)
Note: Firewire Jupiter ExDrive is Plug and Play under Windows XP, 2000
and 98Me. There is no third party driver needed.
Driver Installation for Win98 and Win98SE
After plugging in the cable some system might prompt you for Win98SE CD,
in case you don’t have The Win98SE CD and the wizard prompt you for:
NTMAP.SYS please type C:\WINDOWS\SYSTEM32\DRIVERS
NTMAPHLP.PDR please type C:\WINDOWS\SYSTEM\IOSUBSYS
Reboot your system.
Disk Management for Window 98
1. Select Start > Setting > Control Panel > System. The System Properties
window opens.
2. Select the Device Manager tab, under Device type, Disk Drives, select QTS
FIREWIRE CABLE. Click the Properties button.
3. Select the Settings tab and under the Options box, click the Removable
check box. The Reserved drive letters box becomes active. Select the drive
letter for your new drive. Click Ok.
4. Click Yes to restart your system to make changes take effect.
5. Double click My Computer icon and there should be an extra drive letter
for the Jupiter ExDrive drive. You may now access the drive.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 20
For Windows 2000 & XP Operating Systems
How to use Disk Management
To start Disk Management:
1. Log on as administrator or as a member of the Administrators group.
2. Click Start, click Run, type compmgmt.msc, and then click OK. In the
console tree, click Disk Management. The Disk Management window
appears. Your disks and volumes appear in a graphical view and list view.
3. To customize how you view your disks and volumes in the upper and lower
panes of the window, point to Top or Bottom on the View menu, and then
click the view that you want to use
How to create a new partition or a new logical drive
To create a new partition or logical drive on a basic disk:
1. In the Disk Management window, complete one of the following
procedures, and then continue to step 2:
·
To create a new partition, right-click unallocated space on the basic
disk where you want to create the partition, and then click New
Partition.
·
To create a new logical drive in an extended partition, right-click free
space on an extended partition where you want to create the logical
drive, and then click New Logical Drive.
2. In the New Partition Wizard, click Next.
3. Click the type of partition that you want to create (either Primary
partition, Extended partition, or Logical drive), and then click Next.
4. Specify the size of the partition in the Partition size in MB box, and then
click Next.
5. Decide whether to manually assign a drive letter, let the system
automatically enumerate the drive, or do not assign a drive letter to the
new partition or logical drive, and then click Next
6. Specify the formatting options you want to use by using one of the
following procedures:
·
If you do not want to format the partition, click Do not format this
partition, and then click Next.
·
If you want to format the partition, click Format this partition with
the following settings, and then complete the following procedure in
the Format dialog box:
a. Type a name for the volume in the Volume label box. This is an
optional step. Click the file system that you want to use in the File
system box.
b. You can change the disk allocation unit size, and then specify
whether to perform a quick format, or enable file and folder
compression on NTFS volumes.
Click Next.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 21
7. Confirm that the options that selected are correct, and then click Finish.
The new partition or logical drive is created and appears in the appropriate
basic disk in the Disk Management window. If you chose to format the volume
in step 6, the format process now starts.
How to format a basic volume
To format a partition, logical drive or basic volume:
1. In the Disk Management window, right-click the partition or logical drive
that you want to format (or reformat), and then click Format.
2. In the Format dialog box, type a name for the volume in the Volume label
box. This is an optional step.
3. Click the file system that you want to use in the File system box. If you
want, you can also change the disk allocation unit size, specify whether you
want to perform a quick format, or enable file and folder compression on
NTFS volumes.
4. Click OK.
5. Click OK when you are prompted to format the volume. The format
process starts.
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 22
Technical Support
If you need assistance to get your unit functioning properly, please call
Addonics Technical Support. Our technical staff will be happy to assist you,
but they will need your help to do so. Calling the technical support staff
without all the proper information can be both time consuming and frustrating.
Here are some tips to help you out:
(1)
(2)
(3)
(4)
MODEL NUMBER – Please have this number on hand.
SYSTEM INFORMATION – Type of computer, peripherals, etc.
OPERATING SYSTEM – What version of Windows
WHAT’S THE TROUBLE? – Give enough information
About your problem so that we can recreate and diagnose it.
FREE Software Drivers for all Addonics Technologies
Products are available 24 hours per day at the
Contact Information
Addonics Technologies
2466 Kruse Drive
San Jose CA, 95131
Phone:
Fax:
408-433-3899
408-433-3898
Email:
Internet:
TECHNICAL SUPPORT
Phone:
Hours:
Email:
408-433-3855
8-5 PST
Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 23
|