Sony SUPER HAD CCD SSC CD45 User Manual

3-113-373-01 (1)  
Inside  
B
Features  
7 Mode setting DIP switch  
This is a dome-shaped color video camera for which the 1/3 type Super  
HAD CCD® has been adopted. It has the following features:  
• Manual setting of the camera direction – panning, tilting and rotating  
• Vari-focal auto iris lens as standard equipment. The focal length of the  
lens is from 2.8 mm to 10 mm.  
• High quality CCD and clear dome cover enable high sensitivity.  
• Backlight compensation through the center measurement (SSC-CD45/  
CD45P only).  
• Wide dynamic range (128 times wider than normal) using DynaView  
technology (SSC-CD49/CD49P only)  
• Automatic white balance tracking and adjustment (ATW/ATW-PRO)  
• AC 24 V / DC 12 V power supply system  
Upper  
Lower  
Color Video Camera  
Operating Instructions  
Before operating the unit, please read this manual thoroughly and  
retain it for future reference.  
Position  
Upper (ON) Lower  
Switch  
No.  
1
2
3
INT/LL  
AGC  
LL  
INT  
ON  
ON  
OFF  
OFF  
• Line lock function (24 V AC)  
BLC (SSC-CD45/CD45P)  
DynaView (SSC-CD49/49P)  
Super HAD CCD® is a registered trademark of Sony Corporation.  
DynaViewTM is a registered trademark of Sony Corporation.  
4
ATW  
ATW Pro  
ATW  
1: INT/LL (line lock) switch (Initial setting: LL)  
Use this switch to set the camera synchronization mode to INT  
(internal) or LL (line lock, Only when the power is AC 24 V).  
Notes on Use  
Operating or storage location  
Do not shoot an extremely bright object (an illumination, the sun, etc.).  
Also, avoid operating or storing the camera in the following locations, as  
these can be a cause of a malfunction.  
• Extremely hot or cold places (Operating temperature: –20 °C to  
+50 °C [–4 °F to 122 °F])  
2: AGC (automatic gain control) switch (Initial setting: ON)  
Set to ON to adjust the gain of the video amplifier automatically  
according to the brightness of the object.  
3:  
SSC-CD45/CD45P:  
SSC-CD45/CD45P  
• Exposed to direct sunlight for a long time, or close to heating  
equipment (e.g., near heaters)  
• Close to sources of strong magnetism  
• Close to sources of powerful electromagnetic radiation, such as radios  
or TV transmitters  
BLC (backlight compensation) switch (Initial setting: OFF)  
Use this switch to adjust the exposure to compensate for situations  
where the subject is lit from behind.  
Note  
• Locations subject to vibration or shock  
• Humid or dusty locations  
• Locations exposed to rain  
• Locations under the influence of fluorescent light or reflection of a  
window  
• Under an unsteady light (the image will flicker.)  
When BLC switch is set to ON, a hunting may be generated due to a  
picture. In this case, set BLC switch to OFF.  
SSC-CD49/CD49P  
2007 Sony Corporation Printed in China  
SSC-CD49/CD49P:  
DynaView switch (Initial setting: OFF)  
Set this switch to ON to active the DynaView function.  
Ventilation  
4: ATW switch (Initial setting: ATW)  
ATW: Automatic adjusting function of the white balance, effective for  
use under special light like a sodium lamp.  
English  
To prevent heat buildup, do not block air circulation around the camera.  
Transportation  
When transporting the camera, repack it as originally packed at the  
factory or in materials of equal quality.  
Owner’s Record  
The model and serial numbers are located on the bottom. Record these  
numbers in the spaces provided below.  
ATW Pro: Automatic adjusting function of the white balance according  
to the color temperature based on a fluorescent light, incandescent  
lighting, or natural light.  
Cleaning  
• Use a blower to remove dust from the lens.  
Refer to these numbers whenever you call upon your Sony dealer  
regarding this product.  
5-7: Not used with this unit.  
8 V PHASE (vertical phase) adjustment screw  
• Use a soft, dry cloth to clean the external surfaces of the camera.  
Stubborn stains can be removed using a soft cloth dampened with a  
small quantity of detergent solution, then wipe dry.  
• Do not use volatile solvents such as alcohol, benzene or thinners as  
they may damage the surface finishes.  
Use this screw to adjust the vertical phase of cameras synchronized  
by LL.  
Model No.  
Serial No.  
9 Dome casing screw hole  
WARNING  
To reduce a risk of fire or electric shock, do not expose  
this product to rain or moisture.  
0 Camera installation holes (2 positions)  
Make sure to tighten the screws securely when installing the camera.  
qa Camera head fixing screw  
Note on laser beams  
First loose the screw and face the camera head to the desired  
direction, then tighten the screw to fix it.  
To avoid electrical shock, do not open the cabinet. Refer  
servicing to qualified personnel only.  
Laser beams may damage a CCD. You are cautioned that the surface of a  
CCD should not be exposed to laser beam radiation in an environment  
where a laser beam device is used.  
qs Monitor out jack  
WARNING  
Connect to a video input connector of a monitor . You can adjust the  
camera while looking at the image on the monitor. After adjusting the  
camera, disconnect the cable.  
This installation should be made by a qualified service person and should  
conform to all local codes.  
Typical CCD Phenomena  
WARNING  
Bottom  
qd BNC cable  
C
A readily accessible disconnect device shall be incorporated in the  
building installation wiring.  
The following phenomena may appear on the monitor screen while you  
are using a CCD color video camera. These phenomena stem from the  
high sensitivity of the CCD image sensors, and do not indicate a fault  
within the camera.  
Outputs a composite video signal. Connect to a composite video input  
connector of a video monitor, VCR, etc ( ).  
WARNING (for Installers only)  
Instructions for installing the equipment on the ceiling or the wall:  
After the installation, ensure the connection is capable of supporting at  
least a force of 50 Newtons (N) downwards.  
qf 24V AC/12V DC (power input) cable  
Vertical smear  
A “smear” may appear to extend vertically from very bright subjects, as  
shown below.  
Connect to a 24V AC or 12V DC power supply system ( ). The  
connector tip is a quick-disconnect type. You can screw the cables in  
the tip.  
CAUTION  
The rating label is located on the bottom.  
qg Screw hole for wire rope  
Video monitor screen  
Pale vertical smear  
Power Supply  
Caution for U.S.A. and Canada  
(continued on the reverse side)  
The SSC-CD45/CD49 operates on 24V AC or 12V DC.  
The SSC-CD45/CD49 automatically detects the power.  
Use a Class 2 power supply which is UL Listed (in the U.S.A) or CSA-  
certified (in Canada).  
Very bright subject (such as an  
electric lamp, fluorescent lamp,  
sunlight, or strong reflected light)  
Caution for other countries  
The SSC-CD45/45P/CD49/49P operates on 24V AC or 12V DC.  
The SSC-CD45/45P/CD49/49P automatically detects the power.  
This phenomenon is common to CCD imaging elements using an interline  
transfer system, and is caused when electric charge induced by infrared  
radiation deep within the photo sensor is transferred to the resistors.  
For customers in the U.S.A.  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
Aliasing  
When shooting fine stripes, straight lines or similar patterns, the lines may  
become slightly jagged.  
NOTE: This equipment has been tested and found to comply with the limits  
for a Class A digital device, pursuant to part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference when the equipment is operated in a commercial environment.  
This equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instruction manual,  
may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference in  
which case the user will be required to correct the interference at his own  
expense.  
Blemishes  
A CCD image sensor consists of an array of individual picture elements  
(pixels). A malfunctioning sensor element will show up  
as a single pixel blemish in the image. This is generally not a problem.  
White speckles  
When you shoot a poorly illuminated object at a high temperature, small  
white dots may appear all over the entire screen image.  
You are cautioned that any changes or modifications not expressly approved  
in this manual could void your authority to operate this equipment.  
Location and Function of Part  
All interface cables used to connect peripherals must be shielded in order  
to comply with the limits for a digital device pursuant to Subpart B of Part  
15 of FCC Rules.  
The figure shows the camera without the dome casing and slit cover.  
Side  
A
For Customers in Canada  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est conforme à la norme NMB-003  
du Canada.  
1 Indoor wiring slit (knockout type)  
When you wire indoors, cut this part with a nipper or similar and feed  
the cable through it.  
Note  
For customers in other countries  
Take care not to trap the cable between the camera and ceiling or the wall.  
If the cable is trapped, it may break and cause a fire or electric shock.  
WARNING  
This is a Class A product. In a domestic environment, this product may  
cause radio interference in which case the user may be required to take  
adequate measures.  
2 Camera head holder  
3 Lens  
4 Lens ring fixing screw  
In the case that interference should occur, consult your nearest  
authorized Sony service facility.  
Loosen this screw before adjusting the zoom and focus, then tighten it  
to fix the lens position. The screw can be inserted at one of three  
points.  
ATTENTION  
The electromagnetic fields at specific frequencies may influence the  
picture of the unit.  
5 Zoom ring  
Turn this ring to adjust the field of view.  
6 Focus ring  
Turn this ring to adjust the focus.  
C
B
A
qd  
9
1
7
8
qf  
0
4
2
5
qa  
qs  
3
6
qg  

Wolfcraft QUICK JAW 6134 User Manual
Texas Instruments TITANIUM TI 89 User Manual
Texas Instruments El Dorado CS FX300MS PLUS User Manual
Sony MEX R5 User Manual
Sony DSCH90BBDL User Manual
Sony CFD G505BLACK User Manual
Sirius Satellite Radio Stiletto Vechicle Kit Satellite Radio User Manual
Samsung F7500 User Manual
Samsung ES80 User Manual
Samsung Blu ray BDE5400 User Manual