PYLE Audio View Series PLVW1770IR User Manual

17" Overhead TFT-LCD 16:9 Wide Screen  
Monitor With Infrared Wireless Headphone  
PLVW1770IR  
Usage Notice  
Follow all warnings, precautions and maintenance as  
recommended in this user's manual to maximize the life of your  
LCD monitor  
To avoid the damage of the LCD monitor and risk of electronic  
shock, do not permeate the LCD monitor with water or any  
drink.  
When this happens, turn off the power, unplug the power cord  
and send the LCD monitor to your local dealer or our service  
cen-ter as soon as possible.  
Use a regular power specification of DC 12V . Do not use any  
other power supply different from the regularity.  
Do not place objects on or suspend them with the power cord.  
This will make the power cord damaged.  
Do not assemble or twist the power cord arbitrarily. And do not  
put it together with heated object.  
Do not try to repair the power cord when it is damaged or  
broken, change a new one immediately.  
Avoid any metal objects or inflammable dropping into the LCD  
monitor from ventilation slots.  
Do not attempt to open or disassemble the LCD monitor  
yourself as this may cause electronic shock.  
When there is smile or peculiar smell in use, unplug the power  
cord immediately and send it to your local dealer or our service  
center.  
When there is damage or breach on the LCD monitor casing,  
send it to your local dealer or our service center.  
Do not use this LCD monitor in the areas susceptible to  
excessive dust, dirt, and humid.  
Do not setup the LCD monitor in direct sunlight, extremely hot,  
and cold environment.  
Do not expose the LCD monitor to rain or moisture.  
2
Package  
This LCD monitor comes with all the items below. Check to make sure your unit  
complete. Contact your dealer immediately if anything is missing.  
* 17" High RES TFT-LCD Wide Screen Monitor  
* Overhead Console Mounting Bracket  
* Credit Card Size Remote Control with Batteries  
* Interface Cable with RCA jacks forAudio / Video  
Connection and 12V DC  
* User's Manual  
* Warranty Card  
User Control Overview  
* Panel Control  
POWER  
IR  
MENU  
UP  
DOWN  
MUTE  
3
Function Descriptions  
You may also turn on or off themonitor by this  
"Power" button.  
* Power:  
* Menu:  
Pop up the OSD menus. Press the "Menu" button again  
to exit the OSD menus. When in sub-menu, press "MENU"  
again to go back to the main menu.  
* +/- Keys: 1. Press the "+/-" key to increase or decrease volume.  
2. Make item selection in OSD menus to increase or  
decrease parameters as well.  
* Mute:  
Press the "Mute" button from the remote control  
to still the sound of the LCD monitor.  
Start Your Installation  
* Monitor connection  
2P CAR PPOWER CABLE  
BLACK(-)  
RED(+)  
CAR INDOOR LIGHT  
CONTROL SW  
IR SIGNAL  
FOR TUNER  
(OPTION)  
FUSE  
5M POWER CABLE  
BLACK  
9 PIN MINI DIN  
WHITE  
RED  
(SIGNAL CABLE)  
AUDIO  
( AV1 IN )  
VIDEO  
YELLOW  
WHITE  
RED  
AUDIO  
( AV2 IN )  
VIDEO  
YELLOW  
4
Setting Up The Dome Lamps  
*Operating the dome Lamps  
1. There are three function buttons for the Dome lamps operation: OFF,  
DOOR, and ON. (Refer to the following figure)  
A. OFF:  
To turn off the lamps.  
B. DOOR: To make the lamps turned on  
only when car doors are  
opened.  
C. ON:  
To turn on the lamps.  
ON  
DOOR  
OFF  
* The electric circuit figure  
OFF  
LAMPS  
W
B
DOOR  
R
BATTERY +  
ON  
Power Cord Color  
Point  
Connection  
R
W
B
Connecting With Power Supply  
Red  
White  
Connecting With Sensor of Car Doors  
For Ground Connection  
Black  
* Remarks:  
1. There would be no any power cord puling out from "B" point as  
"B" have been connected with a ground connection by screws.  
2. Power supply should be used in 12 Voltages.  
5
Installation your Monitor  
Take care to select a suitable fitting location and securing method for  
the monitor:  
*The unit should not distract or obstruct the driver.  
*The installation should not inhibit the entry to, or the exit from the  
vehicle.  
*The unit should not interfere with other vehicle components e,g  
(sliding sunroof).  
*Make sure the unit is installed to a secure, robust mounting location  
and cannot become dislodged in the event of an emergency stop.  
*Do not support the unit using only the vehicle interior roof lining.  
*If driving is required, take care not to penetrate through the other  
sheet metal of the vehicle.  
*Avoid prolonged use of the monitor when the engine is not running  
to prevent draining the vehicle battery.  
*Place the mounting metal plate with the nuts facing upward, then,  
mount the monitor by screws included  
6
Operating the Monitor  
* Powering up the monitor  
The monitor will be automatically turned on when releasing the  
monitor from the base unit and "OFF" when it is closed.  
Operating Instructions  
Opening the Monitor  
1. Press the monitor release button to lower the LCD screen.  
2. Lower the monitor until is fixed 90 from the monitor base  
unit for viewing (Refer to the following figure.)  
Closing Monitor  
1. Return the monitor to the central viewing position.  
(Refer to the following figure)  
2. Push the monitor back into the monitor base unit until  
the screen engages with the release button.  
7
* OSD Menus in A/V Source  
A. Source Selection Menu  
SOURCE  
MAIN MENU  
AUTO DETECT  
CUBS.1 = VTSC  
H. SYNC = +15.7K Hz  
V. SYNC = +60.0Hz  
VIDEO 1  
VIDEO 2  
RETURN  
1
BRIGHTNESS  
CONTRAST  
COLOR  
HUE  
SOURCE  
AUDIO  
B. Audio Input Selection Menu  
RECALL  
AUDIO  
EXIT  
MUTE  
VOLUME  
RECALL  
RETURN  
* Quick Adjustment OSD Menus  
1. By pressing "MENU" button, you may open the MAIN MENU, using "+" or "-"  
together to pick out OSD functions.  
2. In order to selectdesire options, it is necessaryto press "MENU" again to  
enter each mode, than using" "/ " " to increase or decrease parameters aswell.  
3. Press "+" or "-" button directly to adjust speaker volume.  
VOLUME  
4. Select out of " EXIT" mode to storing your selected parameter and  
leaving OSD Menus.  
8
Remote Control  
TV/AV  
MUTE  
POWER  
TV/CATV  
TV/CATV interchange  
TV/AV  
Power  
MUTE  
2
1
3
4
Number Pad  
8
5 6  
7
FM/AM  
SETUP  
0
9
SETUP  
Monitor  
Channels convertible(CH)  
Volume control buttons  
Monitor  
UP  
FUNC  
+
VOL  
CH  
DN  
-
MODE  
Appendix  
Changing the New Battery in Remote Control  
1. Push the cassette button to wards the right. (As shown # 1 in below  
figure)  
2. Pull the all battery cassette away from the remote control. As shown  
# 2 in below figure) Change a new battery.  
2
Battery  
Cassette Button  
1
9
Specifications  
Roof Mount Color Display Monitor  
1. Type  
Sync. : Separate TTL sync.  
Video : Composite sync.  
System : NTSC M,N PAL  
SECAM  
2. Signal Input  
Audio : 1.0Vp-p  
3. Display System  
Active Matrix High Resolution TFT-LCD Monitor  
Operating Temperature : 0 C~35 C  
: -20 C~ 60 C  
4. Environment  
Storage Temperature  
Humidity : 20% ~ 90%  
17" High Resolution TFT-LCD 16:9 Wide Screen Flip-Down  
Monitor With Infrared Wireless Headphone and Dome Lights  
Features  
* Active Matrix High Resolution TFT-LCD Monitor  
* 17" Widescreen (16:9) Display  
* Polarized, Anti-glare, Hard Coated Panel  
* 400 cd/m2 brightness for unparalleled picture quality  
* Wide Viewing Angle: H 160 degree, V 160 degree  
* Multi-System Video: NTSC/PAL/SECAM  
* Overhead Console Flip-Down Mounting Bracket Included  
* Wireless Remote Control Included  
* On screen Menu  
* Built-in Twin Dome Lights  
* Interface Cable with RCA Jacks for Easy Connection  
* Dual RCA Audio / Video Inputs.  
* 11~13.8V DC Power source with Noise Filter Circuit  
* Display Colors : 6 bits interface (16 M colors)  
* Infrared wireless headphone included  
10  

Rinnai Q205S User Manual
Raypak H7 504 2004 User Manual
PYLE Audio View Series PLD128 User Manual
Peavey Electronics Car Speaker 3000 User Manual
Panasonic AG HPX174 User Manual
MB QUART FSB213 User Manual
Kodak 4H7269 User Manual
Kenwood DDX5022 User Manual
JVC WR DV1U User Manual
JVC KD LH810 User Manual