Lenmar Enterprises OmniSource Digital Camera Batteries User Manual

Getting Ready  
Choose the adapter plate for the type of battery you will be charging.  
Each of the adapter plates is labeled as to the batteries it can work  
with. If the charger base does not already have the adapter plate you  
want attached, you will need to remove the adapter plate first by  
pushing down on the plate and sliding it to the rear of the charger  
base (away from the LED indicators). Then, attach the selected  
adapter plate to the charger unit by aligning the arrows on the sides  
of the adapter plates and the charger base as shown. While pressing  
down lightly on the adapter plate, slide the plate toward the front of  
the charger base until it locks.  
Operation:  
Plug-in, either the AC 110V or the DC Cigarette Lighter power  
adapter, depending on where you are going to use your OmniSource  
Li-Ion charger unit. Connect the other end of the power adapter cable  
to the power input socket on the charger unit. While the unit is  
receiving power, the red Power Indicator LED on the far right, will  
be on. (See diag.-1).  
OmniSource® Li-Ion  
Universal Charger for Li-Ion Camcorder &  
Digital Camera Batteries  
PLEASE READ THE INFORMATION AND FOLLOW ALL  
INSTRUCTIONS THOROUGHLY BEFORE USING THIS  
PRODUCT.  
Diag.-1  
Introduction  
Connect the battery to the adapter plate on the charger unit, and the  
red Charge Indicator LED in the center will turn on to indicate that  
the unit is fast charging your battery.  
The OmniSource Lithium-Ion (Li-Ion) is a fully automatic  
camcorder battery charger which is compatible with virtually all 3.6  
volt and 7.4 volt Li-Ion batteries for 8mm, VHS-C, digital  
camcorders and digital cameras from Nikon, Kodak, Fuji, Sharp,  
Sony, Canon, JVC, Panasonic, RCA and other manufacturers. In  
addition to the other adapter plates for other Li-Ion battery models.  
Diag.-2  
This charger uses an advanced charging circuit, which provides a  
safe, full charge every time. “Charging” and “Full Charge” status of  
the battery is shown on the built-in LED indicators.  
When the red Charge LED turns off, and the green Charge Complete  
LED, turns on, the charger has switched to “trickle” charge mode  
and the battery is around 90% charged at this time. The battery will  
reach 100% charge within 1-2 hours (depending on the capacity of  
the battery) after the green LED has turned on. Be sure to remove the  
battery from the charger within a few hours after the green LED has  
turned on.  
Flexible power input allows you to use the OmniSource Li-Ion from  
home with its AC Power Supply or on the road using the DC  
Cigarette Lighter Adapter included. Avoid prolonged use in an  
automobile when the engine is not running as it may drain the battery  
in the vehicle.  
Plug-in, either the AC Adapter or the DC Cigarette Lighter power  
adapter, and connect the other end of the power adapter cable to the  
power input jack on the rear of the charger unit.  
Status LED’s  
Together, the three LED’s on the front of the OmniSource Li-Ion  
will indicate the status of the battery and the charger. See the  
descriptions and diagrams included in the following sections  
regarding the various indications and their meaning.  
Diag.-3  

Rockford Fosgate RFP 1410 User Manual
RCA CC6151 User Manual
Raypak RAYTHERM 0180B User Manual
Panasonic HC 902M User Manual
Olympus E M5 Digital SLR Camera E M5 User Manual
Nikon 10x20HG L DCF User Manual
Logitech Surround Sound Speakers Z506 User Manual
Kramer Electronics Bluetooth Headset BT 1 User Manual
JVC LYT0002 0L5A User Manual
JVC KS F383R User Manual