Fusion Electronics Car Speaker PP CM65 User Manual

POWERPLANT  
COMPONENT SPEAKERS  
WARNING: Do not drill mounting holes with speaker in place, as this could allow drill shavings to damage the voice coil.  
Always ensure the audio system is turned off before making any connections to the amplifier, speakers, crossover or  
source unit. Failure to do so could result in permanent damage to the audio system.  
PP-CM525, PP-CM650  
When wiring the speakers, ensure that the wire is protected from sharp metal objects, and always use rubber grommets  
when wire through metal panels. Ensure all terminals and connections are protected from the vehicle chassis and from  
each other.  
Speaker Parameters  
PP-CM5250  
210 Watts  
95 Watts  
50Hz - 22kHz  
4 Ohms  
PP-CM650  
280 Watts  
120 Watts  
40Hz - 22kHz  
4 Ohms  
Max Power Rating  
RMS Power Rating  
Frequency Response  
Impedance  
When connecting the source unit/amplifier crossover and speakers, you connect the positive and negative output wire  
from the source unit/amplifier or crossover, to the corresponding speaker terminals. This will ensure the audio system  
will be in correct phase.  
Sensitivity  
90 dB  
91 dB  
Mounting Depth  
Mounting Diameter  
60mm  
65mm  
125mm  
140mm  
Crossover Specifications  
2-way, passive Butterworth crossover network  
12db/octave slope rates  
Adjustable 3-point tweeter level  
High pass 3.5kHz  
Low pass 4.0kHz  
Installation Guidelines  
Before any wiring and installation is performed, FUSION recommends you first plan the complete installation process.  
Look at the wiring routing, speaker location, and fitment. Make sure you recheck the installation at completion.  
A correct front stage and stereo image can be achieved by proper speaker placement. Ideally, speakers need to be posi-  
tioned where the sound produced is directed at the occupants of the vehicle. The adjustable tweeter supplied with FUSION  
PowerPlant Component Speakers is designed to make this easier.  
Fusion speakers have been designed to fit in many stock or factory positions in the vehicle FUSION recommends a location  
with sufficient air volume behind the speaker, for it to work within its frequency range.  
RECORD YOUR PURCHASE DETAILS HERE:  
MODEL NUMBER __________________________ DATE OF PURCHASE__________________________  
Installation Warning  
1. Ensure the vehicle 12 volt lead is removed from the battery before any equipment is connected.  
2. Investigate the vehicle gas tanks, brake lines, and electrical wiring locations before you begin installation.  
3. Attach the product securely to the vehicle to prevent damage in the event of an accident.  
4. Ensure all wiring is protected to avoid damage or pinching of the cables.  
AFFIX RECEIPT HERE  
Installation Guidelines:  
Bass/mid speaker installation  
1. Ensure there is adequate clearance and depth for the speaker to be mounted  
2. Use the supplied template to mark out the correct diameter hole  
3. Drill four holes for the mounting screws  
WARNING! Audio Systems can produce sound levels over 135dB. Continuous exposure to sound pressure levels over 100dB may  
cause permanent hearing loss! Please watch for emergency vehicles as warning signals may not be heard. USE COMMON SENSE!  
4. Correctly connect the crossover to the speaker. Observe polarity. The striped wire is the positive.  
5. Carefully study the mounting diagram before attempting to mount the speaker. Insert the speaker and grille frame  
and affix with the screws provided. Your PowerPlant speaker is provided with two choices of grille frame. The cus-  
tom grille is screwed directly into the frame of the speaker (see diagram A on reverse side). For the mesh grille,  
first remove the mesh, then fit the speaker and the grille. The mesh is fitted last by simply pushing the tabs on the  
mesh into the self-locking slots in the grille frame. (see diagram B on reverse side).  
V 2.0  
PUBLISHED BY FUSION ELECTRONICS LIMITED:  
YOU CAN HELP PROTECT THE ENVIRONMENT!  
© Copyright 2008 by FUSION Electronics Limited.  
Please remember to respect the local regulations:  
All rights reserved. Specifications and design are  
Hand in the non-working electrical equipment  
subject to change without notice.  
to an appropriate waste disposal center.  

Alpine cda 7873 User Manual
Audiovox P 942 User Manual
axis international marketing 2130R PTZ User Manual
COOLPIX by Nikon Camcorder S5200 User Manual
Crown Boiler JBF EID User Manual
HP (Hewlett Packard) PCI Dual Channel Ultra160 SCSI Host Adapter A6829A User Manual
JBL GTO601 1 User Manual
JL Audio C3 650 XO User Manual
JVC Car Stereo System KD LX50R User Manual
JVC GR AXM4U User Manual