Extron electronic Extron Electronics Cable Box VSC 700 User Manual

Product Category  
VSC 500/700/700D • Setup Guide  
CAUTION:  
Installation and service must be performed by authorized  
personnel only. These units must be installed in accordance  
with national and local electrical codes.  
VSC Remote  
Infrared Remote  
To install the VSC 500/700/700D, follow these steps. For detailed instructions  
see the VSC 500/700/700D User Guide.  
RS-232  
Control  
2
-Y  
-23  
22  
/B  
S
/4  
B
R
O
E
ID  
/Y  
G
-V  
S
-Y  
/R  
R
H
D
E
O
H
R
G
E
H
U
F
-T  
F
R
U
P
B
O
LO  
T
U
P
IN  
A
B
0
.3  
G
R
S
T
0V  
24  
PU  
N
0-  
10  
I
Step 1  
0
/6  
50  
Extron  
VSC 500  
Scan Converter  
Disconnect all power from the VSC and any input or output devices.  
If the scan converter is to be set on top of a table top or other furniture,  
install the self-adhesive feet on the bottom corners of the VSC. If the VSC  
is to be rack mounted, mount the scan converter in a rack (see “Mounting  
the VSC” in the VSC 500/700/700D User Guide).  
Videoconferencing  
System  
VCR  
PC  
Step 2  
BUFFERED  
LOOP-THROUGH  
Attach an input device and a loop-through device to the rear panel  
of the VSC 500.  
RGB INPUT  
INPUTS  
RGB input (VGA) connector  
VSC 500  
Buffered loop-through (VGA) connector  
R
G
B
H/HV  
V
R
G
B
H/HV  
V
Attach an input device and a loop-through device to the  
rear panel of the VSC 700/700D.  
RGBHV  
RGBS  
H/HV  
R
G
B
V
VSC 700  
VSC 700D  
RGB input connectors and buffered loop-through connectors  
RGsB  
Step 3  
R/R-Y  
G/Y  
B/B-Y  
R/R-Y  
H
G/Y  
B/B-Y  
Attach an RGB or component video output device to the rear panel BNC connectors.  
H
V
V
Step 4  
SDI  
Attach an S-video device to the S-video mini DIN connector  
and an SDI device (700D only) to the SDI BNC connector.  
OUTPUTS  
OUTPUTS  
RGBHV  
RGBS  
S-VIDEO  
R/R-Y  
G/Y  
B/B-Y  
R/R-Y  
G/Y  
B/B-Y  
Step 5  
V
V
H
H
Plug the VSC, and input and output devices into a grounded AC source,  
and turn on the input and output devices.  
R-Y, Y, B-Y  
RGsB  
Step 6  
Use the LCD menu screens or RS-232 programming to configure the VSC (in the VSC 500/700/700D User Guide, see the  
“Installation and Operation” and the “RS-232 Programmer’s Guide” sections).  
Step 7  
Use the front panel Adjust horizontal ([) and Adjust vertical ({) adjustment knobs to center the image, then press the Size  
button and rotate the knobs to fill the display screen (see “Front Panel Features” in the VSC 500/700/700D User Guide).  
Step 8  
Use the front panel Menu and Next buttons to navigate to the Filters menu. Using the front panel Adjust horizontal ([)  
or Adjust vertical ({) adjustment knobs, adjust the flicker level from the Flicker filter submenu and adjust the detail level  
from the Horizontal filter submenu (see “Filters menu (Filters)” in the VSC 500/700/700D User Guide).  
Extron USA - West  
Extron USA - East  
Extron Europe  
Extron Asia  
Extron Japan  
Extron China  
Extron Middle East  
Headquarters  
+81.3.3511.7655  
+81.3.3511.7656 FAX  
+971.4.2991800  
+971.4.2991880 FAX  
+800.7339.8766  
Inside Asia Only  
+400.883.1568  
Inside China Only  
+800.633.9876  
Inside USA/Canada Only  
+800.633.9876  
Inside USA/Canada Only  
+800.3987.6673  
Inside Europe Only  
+65.6383.4400  
+65.6383.4664 FAX  
+86.21.3760.1568  
+86.21.3760.1566 FAX  
+1.714.491.1500  
+1.714.491.1517 FAX  
+1.919.863.1794  
+1.919.863.1797 FAX  
+31.33.453.4040  
+31.33.453.4050 FAX  
68-633-50 Rev. A  
03 11  
© 2011 Extron Electronics All rights reserved. www.extron.com  

Breville SLV3100 User Manual
Canon HF R21 User Manual
Canon MV630i User Manual
Canon Optura 30 User Manual
Casio Scientific Calculator fx 300ES User Manual
DeLonghi DFG440 Series User Manual
Eclipse Fujitsu Ten CD2000 User Manual
Eclipse Fujitsu Ten CD3434 User Manual
JVC GET0260 015A User Manual
JVC GR D73 User Manual