MODEL VT440
VT440G
VT540
VT540G
VT440J
VT540J
(Japanese model)
(Japanese model)
LCD Projector
PART No.399911031
SERVICE MANUAL
Better Service
Better Reputation
Better Profit
SAFETY CAUTION:
Before servicing this chassis, it is important that the service
technician read and follow the “Safety Precautions” and “Product
Safety Notice” in this Service Manual.
WARNING:
SHOCK HAZARD - Use an isolation transformer when servicing.
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may
have sufficient magnitude to cause electric shock. Therefore, it is dangerous
to make any kind of contact with any part inside of this unit.
This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any problems.
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
MISE EN GARDE: AFIN DE REDUIRE LES RISQUES D' ELECTROCUTION, NE PAS
DEPOSER LE COUVERCLE, IL N'Y A AUCUNE PIECE
UTILISABLE A L'INTERIEUR DE CET APPAREIL. NE CONFIER
LES TRAVAUX D'ENTRETIEN QU'A UN PERSONNEL QUALIFIE.
Ce symbole a pour but de prévenir I' utilisateur de la présence d'
une tension dangereuse, non isolée se trouvant à l' intérieur de l'
appareil. Elle est d' une intensité suffisante pour constituer un risque
d' électrocution. Eviter le contact avec les pièces à l' intérieur de
cet appareil.
Ce symbole a pour but de prévenir l' utilisateur de la présence d'
importantes instructions concernant l' entretien et le fonctionnement
de cet appareil. Par conséquent, elles doivent être lues
attentivement afin d' éviter des problèmes.
2-1
SAFTY PRECAUTIONS
During servicing carefully observe the following.
5. LAMP
Be very careful of the lamp because it generates high
heat while it is used at high voltage. When replacing
the bulb, make sure it is cool enough.
1. OBSERVE ALL PRECAUTIONS
Items and locations that require special care during serv-
icing, such as the cabinet, chassis, and parts are labelled
with individual safety instructions. Carefully comply with
these instructions and all precautions in the instruction
manual.
6. LENS
Do not look into the lens during projection. This important
to avoid damage to the eyes.
2. BE CAREFUL OF ELECTRIC SHOCK
The chassis carries an AC voltage. If you touch the
chassis while it is still alive, you will get a severe shock.
If you think the chassis is alive, use an isolating
transformer or gloves, or pull out the plug before
replacing any parts.
7. SERVICING
At the time of repair or inspection services, use an earth
band (wrist band), without fail.
8. RUN A COMPLETE SAFETY CHECK AT THE
COMPLETION OF SERVICING
After completion of servicing, confirm that all screws,
parts, and wiring, removed or disconnected for servicing,
have been returned to their original positions. Also
examine if the serviced sections and peripheral areas
have suffered from any deterioration as a result of
servicing. In addition, check insulation between external
metallic parts and blades of wall-outlet plugs. This
examination is indispensable in confirming complete
establishment of safety.
3. USE SPECIFIED PARTS
The components have been chosen for minimum
flammability and for specific levels of resistance value
and withstand voltage. Replacement parts must match
these original specifications. Parts whose specifications
are particularly vital to safe use and maintenance of the
set are marked on the circuit diagrams and parts list.
Substitution of these parts can be dangerous for you
and the customer, so use only specified parts.
(Insulation check)
4. REMOUNT ALL PARTS AND RECONNECT ALL
WIRES AS ORIGINALLY INSTALLED
For safety, insulating tape and tubes are used
throughout, but some lift-off parts on the printed wiring
board require special attention.
All wires are positioned away from high-temperature and
high-voltage parts, and, if removed for servicing, they
must be retuned precisely to their original positions.
Pull out a plug from a wall outlet to disconnect the
connection cable. Then turn on the POWER switch.
Use a 500V megger (Note 2) and confirm that the
insulation resistance is 1MΩ or more between each
terminal of the plug and exposed external metal (Note
1). If the measured value is below the specified level,
then it is necessary to inspect and fix the set.
(Note 1)
Exposed external metal....RGB input terminals, control
terminals, etc.
(Note 2)
If a 500V megger is not available for an unavoidable
reason, then use a circuit tester or the like for inspection.
2-2
LCD Projector
MultiSync VT440/VT540
User’s Manual
IMPORTANT INFORMATION
Precautions
RF Interference
Please read this manual carefully before using your NEC
MultiSync VT440/VT540 Projector and keep the manual
handy for future reference.
WARNING
The Federal Communications Commission does not
allow any modifications or changes to the unit EXCEPT
those specified by NEC Technologies in this manual.
Failure to comply with this government regulation could
void your right to operate this equipment.
Your serial number is located under the name plate label
on the right side of your MultiSyncVT440/VT540.Record
it here:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful in-
terference in a residential installation.This equipment
generates, uses, and can radiate radio frequency en-
ergy and, if not installed and used in accordance with
the instructions, may cause harmful interference to
radio communications. However, there is no guaran-
tee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference
by one or more of the following measures:
CAUTION
To turn off main power, be sure to remove the
plug from power outlet.
The power outlet socket should be installed
as near to the equipment as possible, and
should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPENTHE
CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC
SERVICE PERSONNEL.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio /TV tech-
nician for help.
This symbol warns the user that uninsulated
voltage within the unit may be sufficient to
cause electrical shock. Therefore, it is dan-
gerous to make any kind of contact with any
part inside of the unit.
This symbol alerts the user that important in-
formation concerning the operation and main-
tenance of this unit has been provided. The
information should be read carefully to avoid
problems.
In UK, a BS approved power cable with moulded plug
has a Black (five Amps) fuse installed for use with this
equipment.If a power cable is not supplied with this equip-
ment please contact your supplier.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN
EXTENSION CORD OR IN AN OUTLET UNLESS ALL
THREE PRONGS CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLT-
AGE COMPONENTS INSIDE. ALL SERVICING MUST BE
DONE BY QUALIFIED NEC SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment Regula-
tions.
•
•
•
IBM is a registered trademark of International Business Machines
Corporation.
Macintosh and PowerBook are registered trademarks of Apple
Computer, Inc.
Other product and company names mentioned in this user's manual
may be the trademarks of their respective holders.
3. GSGV Acoustic Noise Information Ordinance:
The sound pressure level is less than 70 dB (A) accord-
ing to ISO 3744 or ISO 7779.
E–2
Important Safeguards
These safety instructions are to ensure the long life of
your projector and to prevent fire and shock.Please read
them carefully and heed all warnings.
CAUTION
Do not unplug the power cable from the wall outlet under any
one of the following circumstances. Doing so can cause damage
to the projector:
* While the Hour Glass icon appears.
Installation
* While the message "Please wait a little." appears. This mes-
sage will be displayed after the projector is turned off.
* Immediately after the power cable is plugged into the wall
outlet (the POWER indicator has not changed to a steady amber
glow).
* Immediately after the cooling fan stops working (The cooling
fan continues to work for 30 seconds after the projector is
turned off with the POWER button).
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away
from dust and moisture.
3. Do not place your projector in direct sunlight, near heaters
or heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm in-
ternal components.
* While the POWER and the STATUS indicators are alternately
flashing.
5. Handle your projector carefully.Dropping or jarring can dam-
age internal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians
in order to ensure proper operation and reduce the risk
of bodily injury.
c. In addition, the ceiling must be strong enough to support
the projector and the installation must be in accordance
with any local building codes.
d. Please consult your dealer for more information.
Power Supply
1. The projector is designed to operate on a power supply of
100-120 or 200-240V 50/60 Hz AC. Ensure that your power
supply fits this requirement before attempting to use your
projector.
2. Handle the power cable carefully and avoid excessive bend-
ing. A damaged cord can cause electric shock or fire.
3. If the projector is not to be used for an extended period of
time, disconnect the plug from the power outlet.
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily
soiled, use a mild detergent. Never use strong detergents
or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful
not to scratch or mar the lens.
E–3
Lamp Replacement
•
To replace the lamp, follow all instructions provided on page
E-33.
•
Be sure to replace the lamp when the message "The lamp
has reached the end of its usable life. Please replace the
lamp."appears.If you continue to use the lamp after the lamp
has reached the end of its usable life, the lamp bulb may
shatter, and pieces of glass may be scattered in the lamp
case. Do not touch them as the pieces of glass may cause
injury. If this happens, contact your NEC dealer for lamp
replacement.
•
Allow a minimum of 30 seconds to elapse after turning off
the projector.Then disconnect the power cable and allow 60
minutes to cool the projector before replacing the lamp.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are
unobstructed to prevent the build-up of heat inside your pro-
jector. Allow at least 3 inches (10 cm) of space between
your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of pa-
per from falling into your projector. Do not attempt to re-
trieve any objects that might fall into your projector. Do not
insert any metal objects such as a wire or screwdriver into
your projector. If something should fall into your projector,
disconnect it immediately and have the object removed by a
qualified NEC service personnel.
3. Do not place any liquids on top of your projector.
•
•
Do not look into the lens while the projector is on. Serious
damage to your eyes could result.
Keep any items such as magnifying glass out of the light
path of the projector.The light being projected from the lens
is extensive, therefore any kind of abnormal objects that
can redirect light coming out of the lens, can cause unpre-
dictable outcome such as fire or injury to the eyes.
•
Do not cover the lens with the supplied lens cap or equiva-
lent while the projector is on. Doing so can lead to melting of
the cap and possibly burning your hands due to the heat
emitted from the light output.
E–4
TABLE OF CONTENTS
Setup ......................................................................... E-31
Orientation ............................................................ E-31
Background ........................................................... E-31
Signal Select ......................................................... E-32
Auto Start .............................................................. E-32
Power Management .............................................. E-32
Power Off Confirmation ......................................... E-32
Keystone Save ...................................................... E-32
Clear Lamp Hour Meter ........................................ E-32
1. INTRODUCTION
Introduction to the MultiSync VT440/VT540 Projector ................. E-6
Getting Started ............................................................ E-6
What’s in the Box ......................................................... E-7
Getting to Know Your MultiSync VT440/VT540 Projector .................. E-8
Front / Side Features .............................................. E-8
Rear / Side Features ............................................... E-9
Top Features ......................................................... E-10
Terminal Panel Features ....................................... E-11
Remote Control Features ...................................... E-12
Help ........................................................................... E-32
Contents................................................................ E-32
Information ............................................................ E-32
2. INSTALLATION
Setting Up Your Projector........................................... E-14
Selecting a Location .................................................. E-14
4. MAINTENANCE
Using a Tabletop or Cart ............................................ E-14
Distance Chart........................................................... E-15
Ceiling Installation ..................................................... E-16
Reflecting the Image.................................................. E-16
Wiring Diagram .......................................................... E-17
Connecting Your PC .............................................. E-18
Connecting Your Macintosh Computer .................. E-19
Connecting an External Monitor............................ E-21
Connecting Your DVD Player................................. E-22
Connecting Your VCR or Laser Disc Player .......... E-23
Replacing the Lamp................................................... E-33
Remote Control Battery Installation........................... E-34
Cleaning or Replacing the Filters .............................. E-34
5. TROUBLESHOOTING
Power / Status Light Messages ................................. E-35
Common Problems & Solutions................................. E-35
6. SPECIFICATIONS
Optical/Electrical/Mechanical..................................... E-36
Cabinet Dimensions .................................................. E-37
D-Sub Pin Assignments............................................. E-38
Timing Chart .............................................................. E-39
PC Control Codes...................................................... E-40
Cable Connection ...................................................... E-40
3. OPERATION
General Controls ....................................................... E-24
Enlarging and Moving a Picture................................. E-24
Using the Menus........................................................ E-25
Menu Tree .................................................................. E-26
Menu Elements.......................................................... E-27
Menu Descriptions & Functions ................................. E-28
Source Select ............................................................ E-28
RGB/Video/S-Video
Picture ....................................................................... E-28
Brightness/Contrast/Color/Hue/Sharpness
Volume....................................................................... E-28
Image Options ........................................................... E-28
Keystone ............................................................... E-28
Color Temperature ................................................ E-28
Lamp Mode ........................................................... E-29
Gamma Correction................................................ E-29
Aspect Ratio.......................................................... E-29
Noise Reduction.................................................... E-29
Color Matrix........................................................... E-29
White Balance ....................................................... E-30
Auto Adjust............................................................ E-30
Position/Clock ....................................................... E-30
Resolution ............................................................. E-30
Factory Default ...................................................... E-30
Menu.......................................................................... E-31
Menu Mode ........................................................... E-31
Basic/Advanced ................................................ E-31
Language .............................................................. E-31
Projector Pointer ................................................... E-31
Source Display ...................................................... E-31
Volume Bar (Direct Button) ................................... E-31
Menu Display Time................................................ E-31
E–5
1. INTRODUCTION
• The supplied remote control can be used without a cable.
• You can control the projector with a PC using the PC Control
port.
• The contemporary cabinet design is light, compact, easy to carry,
and complements any office, boardroom or auditorium.
• Eight pointers are available for your presentation.
Introduction to the MultiSync VT440/VT540 Projector
This section introduces you to your new MultiSync VT440 (SVGA)/
VT540 (XGA) Projector and describes the features and controls.
Congratulations on Your Purchase of The MultiSync VT440/
VT540 Projector
The MultiSyncVT440/VT540 is one of the very best projectors avail-
able today. The MultiSyncVT440/VT540 enables you to project pre-
cise images up to 300 inches across (measured diagonally) from your
PC or Macintosh computer (desktop or notebook),VCR, DVD player,
document camera, or even a laser disc player.
You can use the projector on a tabletop or cart, you can use the pro-
jector to project images from behind the screen, and the projector can
be permanently mounted on a ceiling*1. The remote control can be
used wirelessly.
*1 Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the pro-
jector and the installation must be in accordance with any local
building codes. Please consult your dealer for more information.
*2 An XGA image (1024
ן 768) is converted into an 800ן 600 crisp image with NEC technology’s Advanced AccuBlend on VT440.
*3 An SXGA image (1280
ן 1024) is converted into a 1024ן 768 crisp image with NEC technology’s Advanced AccuBlend on
VT540.
Features you’ll enjoy:
• Simple set up and operation.
• Front ventilation directs hot air away from your audience.
• A high-performance 160 watt NSH (130 watt in Eco mode) lamp.
The lamp life can be extended up to 3000 hours by using the Eco
mode.
• The supplied wireless remote control that operates the projector
from any angle.
• Manual zoom control enables you to adjust the image between
25 (0.63 m) and 300 inches (7.6 m) (measured diagonally).
• Keystone correction allows you to correct trapezoidal distortion
so that the image is square.
Getting Started
The fastest way to get started is to take your time and do everything
right the first time. Take a few minutes now to review the user’s
manual. This may save you time later on. At the beginning of each
section of the manual you’ll find an overview. If the section doesn’t
apply, you can skip it.
• You can choose between video modes depending on your source:
“normal” for a typical picture, “natural” for true color reproduc-
tion.
• An image can be projected from in front or behind a screen, and
the projector can even be installed on the ceiling.
• NEC Technologies’ exclusive Advanced AccuBlend intelligent
pixel blending technology - an extremely accurate image com-
pression technology - offers a crisp image with SXGA (1280 x
1024) resolution*3.
• Supports most IBM VGA, SVGA, XGA*2 , SXGA(with Ad-
vanced AccuBlend)*3, Macintosh, component signal (YCbCr /
YPbPr) or any other RGB signals within a horizontal frequency
range of 15 to 100 kHz and a vertical frequency range of 50 to
117 Hz. This includes NTSC, PAL, PAL60, SECAM and
NTSC4.43 standard video signals.
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
E–6
What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your MultiSync VT440/VT540 Projector.
P O W E R
S T A T U S
O N
O F F
T N E
E
R
/
C
A
N
S E L E C T
Lens cap
C
E
L
S O U R C E
M
E
N
U
A U T O
A D J U S T
RGB
INPUT
AUD
OUTPUT
IN
PC-C
OUT
Projector
S-VIDEO
VID
SOURCE
E
N
U
M
AUTO
ADJ.
Vol.
E
N
SELECT
T
E
R
Vol.
MAGNIFY
POINTER
POWER
C
L
E
A
N
C
PIC
MUTE
HELP
.
RD-36E
Card remote control
String and rivet
ON
1
2
3
4
5
6
DIP
Power cable
Signal cable
Pin adapter for Macintosh
Quick
Connect
Guide
User's
Manual
E–7
Getting to Know Your MultiSync VT440/VT540 Projector
Front/ Side Features
Controls
AC Input
Connectthesuppliedpower
cable’s three-pin plug here.
Remote Sensor
P O W E R
S T A T U S
Remote Sensor
O N
S T A N D B Y
T N E
E
R
/
C
A
N
S E L E C T
C
E
L
S O U R C E
M
E
N
U
A U T O
A D J U S T
Air-Filter (inlet)
Slot for Kensington
MicroSaver
Security System
RGB
INPUT
AUD
Lens Cap
OUTPUT
IN
PC-C
OUT
Air-Filter (inlet)
S-VIDEO
VID
Adjustable Tilt Foot Button
Adjustable Tilt Foot
Carrying Handle
Terminal Panel
Zoom Lever
Focus Ring
Lens
Ventilation (outlet)
NOTE: Built-in Security Slot (
)
Carrying the Projector:
Raise the carrying handle up. Always carry your projector by the
carrying handle.
®
This security slot supports the MicroSaver Security System.
®
MicroSaver is a registered trademark of Kensington Microware
Inc.The logo is trademarked and owned by Kensington Microware
Inc.
NOTE:When moving the projector or when it is not in use, cover the
lens with the lens cap.
O
/
ON
L
E
C N
A
C
AJDUST
R
E
ATUO
SELCT
U
P C - C O N T R O L
O U T P U T
N
PWOER
E
AUTS
M
S - V I D E
V I D E O
I N P U T
R G B
O U T
I
I N
O U T
A U D
SUORCE
E–8
Rear/ Side Features
Remote Sensor
ADJUST
AUTO
U
N
E
M
SOURCE
L
E
C
SELECT
AN
C
STAND BY
/
R
E
N
T
E
ON
Remote Sensor
STATUS
POWER
Built-in Monaural Speaker (1W)
Rear Foot
Lamp Cover
Lamp Cover Screw
Card Remote Slot
Rear Foot
Attaching the lens cap to the lens hood with the sup-
plied string and rivet
1. Thread the string through the hole on the lens cap and then tie a
Slot for Card Remote Control
The supplied card remote control can be stored in the cabinet.
To store the card remote control:
1. Insert the card remote control STRAIGHT into the slot.
2. Push the card remote control until it is into place.
knot in the string.
Lens Cap
AUTO
ADJ.
L
E
C
N
A
C
.
Vol.
PCI
2. Tie a knot again
S
U
String
T
MUTE
N
Vol.
E
M
PWOER
PIONTER
R
E
T
E
N
HLEP
R-D36E
MGANIFY
To pull out the card remote control:
1. Push the bottom of the card remote control straight to eject the
card remote control.
3. Use the rivet to attach the string to the bottom of the lens hood.
2. Pull out the card remote control.
Rivet
R-D36E
S - V
V I D
U T
I N
V I D
A U D
U T
I N
NOTE: Do not push or pull the card remote control in a slanting
direction. Unless you push the card remote control straight, you may
not eject the card remote control. Should this happen, try pushing the
card remote control straight again.
A U D
E–9
Top Features
1
SOURCE
2
4
5
M
E
AUTO
N
U
7
ADJUST
SEECT
E
N
STATUS
POWER
E
R
C
A
N
C
E
L
3
ON
/
STAND BY
6
8
9
1 Source Button
6 Cancel Button
Use this button to select a video source such as a PC, VCR or DVD
player.
Press this button to exit the menu. Press this button to return the
adjustments to the last condition while you are in the adjustment
or setting menu.
2 Auto Adjust Button
Use this button to adjust Position-H/V and Pixel Clock/Phase for
an optimal picture. Some signals may not be displayed correctly or
take time to switch between sources.
7 Status Indicator
When this is lit red (orange in Eco mode) continually, it’s warning
you that the projection lamp has exceeded 2000 hours (up to 3000
hours in Eco mode) of service. After this light appears, it is advis-
able to replace the projection lamp as soon as possible. (See page
E-33). In addition the message “ The lamp has reached the end of
its usable life. Please replace the lamp.” appears continually until
the lamp is replaced.
If this light blinks red rapidly, it indicates that the lamp cover or
filter cover is not attached properly or the projector is overheated.
See the Power / Status Light Messages on page E-35 for more
details.
3 Menu Button
Displays the menu.
4 Select (▲▼ᮤ ᮣ) / Volume (+) (–) Buttons
▲▼: Use these buttons to select the menu of the item you wish
to adjust.
ᮤ ᮣ: Use these buttons to change the level of a selected menu
item.
A press of the ᮣ button executes the selection. When no menus
appear, these ▲▼ buttons work as a volume control.
When the pointer is displayed, these ᮤ ᮣ ▲▼ buttons move the
pointer.
8 Power Indicator (
When this indicator is green, the projector is on; when the indica-
tor is orange, it is in standby mode.
)
5 Enter Button
9 Power Button (ON / STAND BY)
Executes your menu selection and activates items selected from
the menu.
Use this button to turn the power on and off when the power is
supplied and the projector is in standby mode.
NOTE: To turn off the projector, press and hold this button for
minimum of two seconds.
E–10
Terminal Panel Features
AUDIO
RGB
P O W E R
S T A T U S
INPUT
O N
S T A N D B Y
T N E
E
R
/
C
A
N
S E L E C T
C
3
4
1
E
L
S O U R C E
M
E
N
U
IN
OUT
A U T O
A D J U S T
OUTPUT
OUT IN
8
2
PC-CONTROL S-VIDEO
VIDEO
Slot for Kensington
MicroSaver Security System
5
7
6
1. RGB Input Connector(Mini D-Sub 15 pin)
5. Video Input (RCA)
Connect your PC or other RGB equipment. Use the supplied sig-
nal cable to connect to a PC.
Connect a VCR, DVD player, laser disc player, or document cam-
era here to project video.
2. RGB Monitor Output Connector (Mini D-Sub 15 pin)
You can use this connector to loop your computer image to an
external monitor from the RGB input source.
6. S-Video Input Port (Mini DIN 4 Pin)
Connect the S-Video input from an external source like a VCR.
7. PC Control Port (Mini DIN 8 Pin)
3. Audio Input / Output Mini Jack
Use this port to connect your PC to control your projector. This
enables you to use your PC and serial communication protocol to
control the projector. If you are writing your own program, typical
PC control codes are on page E-40.
This is where you connect audio output from your computer. Or
connect additional external speakers here to listen to audio coming
from your Video or S- Video input.
A cap is put on the port at the factory. Remove the cap when using
the port.
4. Audio Input / Output Connector (RCA)
This is where you connect audio output from a VCR, DVD player,
or laser disc player. Or connect additional external speakers to lis-
ten to audio coming from your RGB source.
8. Built-in Security Slot (
)
This security slot supports the MicroSaver ® Security System.
MicroSaver ® is a registered trademark of Kensington Microware
Inc. The logo is trademarked and owned by Kensington Microware
Inc.
NOTE: Either connector 3 or 4 can be used for input or output, how-
ever they cannot both be used for input simultaneously. It can dam-
age your equipment.
E–11
Remote Control
12
Remote Control Features
1 Source Button
Press to select a video source.
1
3
AUTO
ADJ.
SOURCE
2
4
2 Auto Adjust Button
Use this button to adjust Position-H/V and Pixel Clock/Phase for
an optimal picture. Some signals may not be displayed correctly,
or in some cases it may take some time for a source to switch be-
tween sources.
Vol.+
SELECT
Vol.–
3 Menu Button
Displays the menu.
4 Select (▲▼ᮤ ᮣ) / Volume (+) (–) Buttons
▲▼: Use these buttons to select the menu of the item you wish
to adjust.
ᮤ ᮣ: Use these buttons to change the level of a selected menu
item.
A press of the ᮣ button executes the selection. When no menus
appear, these ▲▼ buttons work as a volume control.
When the pointer is displayed, these ᮤ ᮣ ▲▼ buttons move the
pointer.
6
8
5
7
PIC.
POINTER
MUTE
9
MAGNIFY
HELP
POWER
11
5 Enter Button
Use this button to enter your menu selection.
RD-366E
6 Cancel Button
10
Press this button to exit “Menus”. Press this button to return the
adjustments to the last condition while you are in the adjustment
or setting menu.
NOTE: Remove the transparent insulation tape before use. See
page E-34 for battery installation.
7 Magnify Button
H
N
A
P
Use the (+) or (–) button to adjust the image size up to 400%.
When the Pointer is displayed, the magnified image is displayed at
the center of the Pointer. When the Pointer is not displayed, the
magnified image is displayed at the center of the screen.
When the image is magnified, the pointer is changed to the magni-
fying icon.
A
J
T
L
M
CR2025O
V
nO
3
2
-
LiC
L
L
E
8 Pointer Button
12 Infrared Transmitter
Press this button to display one of the eight pointers; press again to
hide the pointer. You can move your pointer icon to the area you
want on the screen using the Select button.
Direct the remote control toward the remote sensor on the projec-
tor cabinet.
Remote Control Precautions
9 Picture Mute Button
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
This button turns off the image and sound for a short period of
time. Press again to restore the image and sound.
10 Help Button
• Do not place the battery upside down.
Provides information about operation and adjustment procedures
or the set information for the current menu or adjustment during
menu operation. This also displays information how to use the Help.
NOTE: Before you use the card remote control for the first time, be
sure to remove the insulation tape from the card remote control.
* Keep the coin cell battery out of reach of children so as not to
allow them to swallow the cell battery.
11 Power Button
If power is applied, you can use this button to turn your projector
on and off.
CAUTION:
NOTE: To turn off the projector, press and hold the POWER but-
ton for a minimum of two seconds.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer.
Dispose of used batteries according to your local regulations.
E–12
Operating Range
7m
22 feet
30˚
30˚
7m
7m
22 feet
E–13
2. INSTALLATION
This section describes how to set up your MultiSync VT440/VT540
projector and how to connect video and audio sources.
4. Move the projector left or right to center the image horizontally
on the screen.
5. To center the image vertically, lift the front edge of the projector
and press the One-Touch Tilt button on the front side of the pro-
jector to release the Front Adjustable foot.
Setting up Your Projector
Your MultiSync VT440/VT540 Projector is simple to set up and use.
But before you get started, you must first:
1. Determine the image size.
Screen
Side view
2. Set up a screen or select a non-glossy white wall onto which you
can project your image.
Carrying the Projector: Always carry your projector by the handle.
Ensure that the power cable and any other cables connecting to video
sources are disconnected before moving the projector.
When moving the projector or when it is not in use, cover the lens
with the lens cap.
(There is approximately 10 degrees of up and down adjustment
for the front of the projector.)
Carrying handle
O
/
ON
L
E
C N
A
C
AJDUST
R
E
ATUO
SELCT
U
P C - C O N T R O L
O U T P U T
N
PWOER
E
AUTS
M
S - V I D E O
V I D E O
I N P U T
R G B
O U T
I N
I N
O U T
A U D
Adjusting the Tilt Foot
SUORCE
1) Press and hold the Tilt button on the front of the projector.
2) Lift the front edge of the projector to the height you want, and
release the button to lock the Adjustable Tilt Foot.
P O W E R
S T A T U S
O N
O F F
Selecting a Location
E T N E
R
/
C
A
N
S E L E C T
C
E
L
S O U R C E
M
E
N
U
The further your projector is from the screen or wall, the larger the
image. The minimum size the image can be is approximately 25"
(0.64 m) measured diagonally when the projector is roughly 4 feet
(1.2 m) from the wall or screen. The largest the image can be is 300"
(7.6 m) when the projector is about 39.3 feet (12.0 m) from the wall
or screen.
A U T O
A D J U S T
AUD
IN
2
UT
I
I
1
Using a Tabletop or Cart
1. Place your projector on a flat level surface at the optimal distance
from the screen or wall so you realize the size image you want.
(Avoid having bright room lighting or sun light directly on the
screen or wall where you’ll be projecting the image.)
2. Connect the power cable, remove the lens cap and turn the projec-
tor on. (If no input signal is available, the projector will display a
background image.)
To fine-tune the image’s position vertically on the screen, rotate the
foot. Each of the rear feet height can be changed up to 0.6” (4mm).
C T
L
S O U R C E
M
E
N
U
A U T O
A D J U S T
3. Ensure that the projector is square to the screen.
RGB
INPUT
AUD
OUTPUT
IN
PC-CO
OUT
S-VIDEO
VID
Top view
Screen
S
POW
6. If the projected image does not appear square to the screen then
use keystone correction for proper adjustment.
7. Adjust the size of the image using the Zoom ring on the lens.
E–14
Distance Chart
C
A: Distance between the
lens and the screen cen-
ter
Screen (inch)
A
H
C: Horizontal throw dis-
tance between screen
surface and the lens
D: Vertical distance be-
tween projector base
and base of image
E: Vertical distance be-
tween projector base
and screen center
E
D
α
4:3 Diagonal
Formulas(mm)
Formulas(inch)
"H = Horizontal Screen Width
A = C/cosα
"H = Horizontal Screen Width
A = C/cosα
C (wide) = 36.8712 × (diagonal screen size/ 0.92205) – 43.5689
C (tele) = C(wide) × 1.2
C (wide) = (36.8712 × (diagonal screen size/0.92205) – 43.5689) / 25.4
C (tele) = C (wide) × 1.2
D = 1.45 × M – 62.9
E = 62.9 + 5.5M
D = 1.45 × M – 62.9 / 25.4
E = (62.9 + 5.5M) / 25.4
M = 1.25H / 22.86
M = 1.25H / 0.9
Zoom Lens (Wide)
α
degree
9.01
0.16
0.99
8.93
0.16
0.99
8.85
0.15
0.99
8.82
0.15
0.99
8.81
0.15
0.99
8.79
0.15
0.99
8.78
0.15
0.99
8.77
0.15
0.99
8.75
0.15
0.99
8.74
0.15
0.99
8.74
0.15
0.99
8.73
0.15
0.99
8.72
0.15
0.99
8.72
0.15
0.99
β (=sinα)
γ (=cosα)
Screen Size H-Width
inch
inch
24
30
32
40
48
60
56
70
64
80
72
90
80
96
120
150
144
180
160
200
192
240
216
270
240
300
4:3 Diagonal
100
120
A
C
D
E
mm
inch
mm
inch
mm
inch
mm
inch
1171
46
1156
46
-15
-1
246
10
1575
62
1556
61
2
0
2384
94
2356
93
34
1
2789
110
2756
108
50
2
491
19
3193
126
3155
124
66
3
552
22
3598
142
3555
140
82
3
613
24
4002
158
3955
156
98
4
674
27
4811
189
4755
187
130
5
6025
237
5955
234
179
7
7238
285
7154
282
227
9
8047
317
7954
313
259
10
9666
381
9554
376
324
13
10879
428
10753
423
372
15
12093
476
11953
471
420
17
307
12
430
17
796
31
980
39
1163
46
1285
51
1530
60
1713
67
1896
75
Zoom Lens (Tele)
α
degree
6.28
0.11
0.99
7.46
0.13
0.99
7.39
0.13
0.99
7.37
0.13
0.99
7.36
0.13
0.99
7.35
0.13
0.99
7.34
0.13
0.99
7.32
0.13
0.99
7.31
0.13
0.99
7.30
0.13
0.99
7.30
0.13
0.99
7.29
0.13
0.99
7.29
0.13
0.99
7.28
0.13
0.99
β (=sinα)
γ (=cosα)
Screen Size H-Width
inch
inch
20
25
32
40
48
60
56
70
64
80
72
90
80
96
120
150
144
180
160
200
192
240
216
270
240
300
4:3 Diagonal
100
120
A
C
D
E
mm
inch
mm
inch
mm
inch
mm
inch
1396
55
1387
55
-23
-1
216
8
1883
74
1867
74
2
0
2851
112
2827
111
34
1
430
17
3334
131
3307
130
50
2
491
19
3818
150
3787
149
66
3
552
22
4302
169
4266
168
82
3
613
24
4785
188
4746
187
98
4
674
27
5753
226
5706
225
130
5
7204
284
7146
281
179
7
8655
341
8585
338
227
9
9623
379
9545
376
259
10
11558
455
11464
451
324
13
13009
512
12904
508
372
15
14460
569
14344
565
420
17
307
12
796
31
980
39
1163
46
1285
51
1530
60
1713
67
1896
75
NOTE: Distances may vary +/–5%.
Distance Chart
300
250
300
250
Throwing Distance Screen Size (inch)
(inch)
45
(m)
1.2
1.6
2.4
2.8
3.2
3.6
4.0
4.8
6.0
7.2
8.0
9.6
10.8
12.0
Wide
30
Tele
25
200
150
200
150
61
40
33
93
60
50
108
124
140
156
187
234
282
313
376
423
471
70
80
90
58
67
75
83
100
125
150
167
200
225
250
100
50
0
100
50
0
100
120
150
180
200
240
270
300
0
100 200
300
400
0
2
4
6
8
10 12
Throwing Distance (inch)
Throwing Distance (m)
wide
tele
E–15
Ceiling Installation
Formulas(mm)
H” = Horizontal Screen Width (inch)
A = C/cosα
B = 94 + 5.5 × M
C (wide) = 36.8712 × (diagonal screen size/ 0.92205) – 43.5689
C (tele) = C(wide) × 1.2
F = 1.4516 × M – 94
F
B
V I D E O
O U T
S - V I D E O
P C - C O N T R O L
I N
O U T P U T
O U T I N
I N P U T
R G B
A U D I O
α
M = 1.25H” / 22.86
Formulas(inch)
H” = Horizontal Screen Width
A = C/cosα
B = (94+5.5 × M) / 25.4
A
C
(wide) = (36.8712 × (diagonal screen size/0.92205) – 43.5689) / 25.4
C (tele) = C (wide) × 1.2
F = 1.4516 × M – 94/25.4
M = 1.25H / 0.9
C
A: Distance between the lens and the screen center
B: Vertical distance between the top of the supplied ceiling mount and the screen center
C: Horizontal throw distance between screen surface and the lens
F: Vertical distance between projector base and top of image
Zoom Lens (Wide)
α
degree
9.01
0.16
0.99
24
30
1171
46
1156
46
277
11
-46
-2
8.93
0.16
0.99
32
40
1471
58
1452
57
338
13
-29
-1
8.85
0.15
0.99
48
60
2242
88
2214
87
461
18
3
0
8.82
0.15
0.99
56
8.81
0.15
0.99
64
8.79
0.15
0.99
72
8.78
0.15
0.99
80
100
3785
149
3738
147
705
28
8.77
0.15
0.99
96
120
4556
179
4500
177
827
33
8.75
0.15
0.99
120
150
5713
225
5644
222
1011
40
8.74
0.15
0.99
144
180
6870
270
6787
267
1194
47
8.74
0.15
0.99
160
200
7641
301
7549
297
1316
52
8.73
0.15
0.99
192
240
9184
362
9074
357
1561
61
8.72
0.15
0.99
216
270
10341
407
10217
402
1744
69
341
13
8.72
0.15
0.99
240
300
11498
453
11360
447
1927
76
390
15
β (=sinα)
γ (=cosα)
Screen Size H-Width
4:3 Diagonal
A
inch
inch
mm
inch
mm
inch
mm
inch
mm
inch
70
80
90
2628
103
2595
102
522
21
3013
119
2976
117
583
23
3399
134
3357
132
644
25
C
B
F
19
1
35
1
51
2
67
3
100
4
148
6
196
8
229
9
293
12
Zoom Lens (Tele)
α
degree
6.28
0.11
0.99
20
25
1396
55
1387
55
247
10
-54
-2
7.1
0.12
0.99
32
40
1902
75
1887
74
338
13
-29
-1
7.0
0.12
0.99
48
7.0
0.12
0.99
56
7.0
0.12
0.99
64
7.0
0.12
0.99
72
6.9
0.12
0.99
80
100
4896
193
4860
191
705
28
6.9
0.12
0.99
96
120
5893
232
5851
230
827
33
6.9
0.12
0.99
120
150
7390
291
7337
289
1011
40
6.9
0.12
0.99
144
180
8887
350
8823
347
1194
47
6.9
0.12
0.99
160
200
9885
389
9814
386
1316
52
6.9
0.12
0.99
192
240
11881
468
11796
464
1561
61
293
12
6.9
0.12
0.99
216
270
13378
527
13282
523
1744
69
341
13
6.9
0.12
0.99
240
300
14875
586
14768
581
1927
76
390
15
β (=sinα)
γ (=cosα)
Screen Size H-Width
4:3 Diagonal
A
inch
inch
mm
inch
mm
inch
mm
inch
mm
inch
60
70
80
90
2900
114
2878
113
461
18
3399
134
3373
133
522
21
3898
153
3869
152
583
23
4397
173
4364
172
644
25
C
B
F
3
0
19
1
35
1
51
2
67
3
100
4
148
6
196
8
229
9
If your projector is mounted on the ceiling and your image is upside
down, use the “Menu” and “Select” buttons on your projector cabi-
net or ▲▼ button on your remote control to correct the orientation.
(See page E-31.)
WARNING
• Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more informa-
tion.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the projec-
tor falls to the ground, you can be injured and the projector
severely damaged.
• Do not use the projector where temperatures vary greatly. The
projector must be used at temperatures between 32˚F (0˚C)
and 95˚F (35˚C).
Reflecting the Image
Using a mirror to reflect your projector’s image enables you to enjoy
a much larger image. Contact your NEC dealer if you need a mirror.
If you’re using a mirror and your image is inverted, use the “Menu”
and “Select” buttons on your projector cabinet or ▲▼ buttons on
your remote control to correct the orientation. (See page E-31.)
• Do not expose the projector to moisture, dust, or smoke. This
will harm the screen image.
• Ensure that you have adequate ventilation around your pro-
jector so heat can dissipate. Do not cover the vents on the side
or the front of the projector.
E–16
Wiring Diagram
Macintosh or Compatibles
(Desktop type or notebook type)
Pin adapter for Macintosh (supplied)
Speaker System
IBM VGA or Compatibles
(Desktop type or notebook type)
RGB INPUT
AUDIO
IN
OUT
IN
Monitor
RGB OUTPUT
OUT
Signal cable (supplied)
To mini D-Sub 15-pin connector on the
projector. It is recommended that you
use a commercially available distribution
amplifier if connecting a signal cable
longer than the supplied cable.
PC CONTROL
S-VIDEO
VIDEO
DVD Player (with component output)
Optional Component V cable
VCR, DVD Player or LaserDisc Player
Document Camera
To video, S-video, and audio
inputs on the projector.
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC
before turning on the power to the notebook PC. In most cases signal cannot be output from RGB output
unless the notebook PC is turned on after connecting with the projector.
NOTE:
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-
saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait 30 seconds and then press the
POWER button again to resume.
NOTE: If using video, S-video, or audio cables, the cables should be 3 m (9.8 feet) or shorter.
E–17
Connecting Your PC
Signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is recom-
mended that you use a commercially available distribution ampli-
fier if connecting a signal cable longer than the supplied one.
IBM VGA or Compatibles
(Notebook type)
RGB INPUT
RG
INP
AIO
AUDIO
OUTPUT
IN
OUT
PC-
OUT
IN
S-VIDEO
IBM VGA or Compatibles
VIDEO
(Desktop type)
Audio cable
(not supplied)
Connecting your PC to your MultiSync VT440 (SVGA)/ VT540 (XGA) projector will enable you to project your computer’s screen image for
an impressive presentation.
To connect to a PC, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC to the projector.
3. Turn on the projector and the computer.
4. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you’ve connected to the
projector.
E–18
Connecting Your Macintosh Computer
Macintosh (Notebook type)
Signal cable
(supplied)
RGB INPUT
RG
INP
ADI
Audio cable
AUDIO
(not supplied)
OUTPUT
IN
OUT
IN
PC-C
OUT
S-VIDEO
VIDEO
Macintosh (Desktop type)
NOTE: The new Macintosh computer
such as G3 will have the 15 pin HD con-
nector. The VT440/VT540's "Plug and
Play" data will be downloaded to the
Macintosh. Therefore, the Mac adapter
will not be necessary.
To connect to a Macintosh, simply:
1. Turn off the power to your projector and your Macintosh com-
puter.
DIP
ON
2
3
4
5
6
1
2. Use the supplied signal cable to connect your Macintosh com-
puter to the projector.
3. Turn on the projector and the Macintosh computer.
For older Macintosh,
use the supplied pin
adapter to connect to
your Mac's video
port.
Pin adapter for Macintosh
(supplied)
E–19
When using a Macintosh computer with the projector, set the DIP
switches of the supplied pin adapter according to your resolution.
After setting, restart your Macintosh computer.
See the following pages for setting of the DIP switches.
• When using with a Macintosh, SVGA(800
ן 600 :VT440)/ XGA(1024
ן 768 : VT540) is recommended if your Macintosh supports this mode.
• When using with a Macintosh PowerBook, output may not be
set to 800
ן 600 unless “mirroring” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh com-
puter for mirroring.
NOTE: A Video Adapter cable manufactured by Apple Computer is
needed for a PowerBook which does not have a mini D-Sub 15-pin
connector.
Settings for Monitor Mode
Number of DIP switch
1
2
3
4
5
6
Resolution
13" multi-scan mode /16"-13"
17" multi-scan mode /19"-13"
21” multi-scan mode /21"-13"
13" fixed mode /640x480
VGA/SVGA mode
16" fixed mode /832x624
19" fixed mode /1024x768
21" fixed mode /1152x870
ON
ON
ON
ON
ON
ON
ON
ON
ON ON
ON
ON
ON
ON
ON
ON
ON ON
ON ON
ON
ON
NOTE: For settings other than display modes supported by your
Macintosh and the projector, use of the DIP switch may bounce an
image slightly or may display nothing. If this happens, set the DIP
switch to the 13" fixed mode and then restart your Macintosh. After
that, restore to a displayable mode and then restart the Macintosh
again. Make sure that the projector and your Macintosh are con-
nected with the pin adapter and the supplied signal cable (mini D-
Sub 15-pin connector) and then restart your Macintosh.
Examples of DIP switch setting
17" multi-scan mode
VGA/SVGA mode
19" fixed mode
ON
ON
ON
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
NOTE: Refer to your computer’s owner’s manual for more informa-
tion about your computer’s video output requirements and any spe-
cial identification or configuring your projector’s image and moni-
tor may require.
E–20
Connecting an External Monitor
External monitor
RGB
INPUT
AUDIO
AUDIO IN
T
OUT
IN
PC-C
OUT
AUDIO OUT
RGBSO-VUIDETOPUT
VIDEO
You can connect a separate, external monitor to your VT440/VT540 to simultaneously view on a monitor the image you're projecting. To do so:
1. Turn off the power to your projector, monitor and computer.
2. Use a 15-pin cable to connect your monitor to the RGB Monitor Output (Mini D-Sub 15 pin) connector on your projector.
3. Turn on the projector, monitor and the computer.
E–21
Connecting Your DVD Player
DVD player
RGB INPUT
R
INP
Y
Cb Cr
Cr
ADIO
Cb
R
L
OUTPUT
Y
IN
OUT
PC-C
OUT
White
IN
S-VIDEO
Red
VIDEO
Optional 15-pin-to-RCA
ן 3 cable (Component V )
Audio Equipment
Audio cable
(not supplied)
R
L
White
Red
You can connect your projector to a DVD player with component outputs or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use the optional 15-pin-to-RCA
ן 3 cable to connect your DVD player to the RGB INPUT connector on the projector.
For a DVD player without component video (Y,Cb,Cr) outputs, use common RCA cables (not provided) to connect a composite VIDEO
output of the DVD player to the Video Input of the projector.
3. Turn on the projector and DVD player.
NOTE: Refer to your DVD player’s owner’s manual for more information about your DVD player’s video output requirements,
E–22
Connecting Your VCR or Laser Disc Player
VCR/ Laser disc player
RGB
INPUT
AUDIO
IN
OUTPUT
OUT
S-VIDEO
OUT
IN
S-VIDEO
L
VIDE
VIDEO
R
S-video cable
(not supplied)
White
Red
Document camera
Audio equipment
Audio cable
(not supplied)
VIDEO
L
R
White
Red
Video cable (not supplied)
Use common RCA cables (not provided) to connect your VCR, laser disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the
Video input on your projector. Use an audio cable (not supplied) to connect the audio from your VCR or laser disc player to your audio
equipment (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo
sound.
3. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owner’s manual for more information about your equipment’s video output requirements.
E–23
3.OPERATION
This section describes how to select a computer or video source, how
to adjust the picture, and how to customize the menu or projector
settings.
Enlarging and Moving a Picture
You can enlarge the area you want up to 400 percent.
To do so:
1) Press the POINTER button on the card remote control to dis-
play the pointer.
General Controls
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
1. Turn on the Projector
POINTER
Plug the supplied power cable in the wall outlet. The projector
will go into its standby mode and the power indicator will glow
orange.
Only after you press the “POWER” button on the projector cabi-
net or the remote control will the power indicator turn to green
and the projector become ready to use.
NOTE: To turn the projector on by plugging in the power cable,
use the menu and enable the “Auto Start” feature. (See page E-
32.)
2) Move the pointer to the area you want to enlarge.
NOTE: Regardless of the lamp mode setting, the lamp always stays
in High-Bright mode for 3 minutes after the projector is turned
on. If you have selected the Eco mode, the STATUS indicator blinks
green and the lamp will change to Eco mode in 3 minutes.
Vol.
SELECT
Vol.
2. Select the Computer or Video Source
Press the Source button on the remote control or the projector
cabinet to select “Video” (VCR, document camera, or laser disc
player), S-Video” or “RGB” (computer or DVD with component
output) to display the image.
3) Adjust the image size up to 400 percent.
Or press the “Menu” button on the remote control or the cabinet
and use the menu to select your video source: “Video”, “S-Video”
or “RGB”.
3. Adjust the Image Size and the Focus
MAGNIFY
Use the Zoom lever to adjust the image size, then use the Focus
ring to obtain the best focus.
Use the “Magnify” button (+) or (-) on the remote control to make
the image larger up to 400%.
4. Turning off the Projector
First press the “POWER” button on the projector cabinet or the
remote control for a minimum of two seconds. The power indica-
tor will glow orange.After the projector turns off, the cooling fans
keep operating for 30 seconds.
Do not disconnect the power cable during this time. Then, unplug
the power cable. The power indicator will go out.
MAGNIFY
IMPORTANT:
• The projector should be unplugged if it will not to be used for an
extended period.
• To turn off the image and sound briefly (five minutes or less),
use the “Picture Mute” button instead of turning the projector
off and on.
• The projector will display a black, blue image or logo if no input
signal is present.
• Do not turn the projector off and then immediately back on. The
projector needs to cool for 30 seconds before it can be restarted.
E–24
Using the Menus
NOTE: An interlaced motion video image may be blurred while
the menu is displayed.
1. Press the “Menu” button on the remote control or the projector
cabinet to display the Main Menu.
2. Press the ▲▼ buttons on the remote control or the projector cabi-
net to highlight the menu for the item you want to adjust or set.
3. Press the ᮣ button or the “Enter” button on the remote control or
the projector cabinet to select a submenu or item.
4. Adjust the level or turn the selected item on or off by using “Se-
lect” ᮤ or ᮣ buttons on the remote control or the projector cabi-
net. The on-screen slide bar will show you the amount of increase
or decrease.
5. The change is stored until you adjust it again.
ENTER:
Stores the setting or adjustments.
CANCEL: Return to the previous screen without storing settings
or adjustments.
6. Repeat steps 2-5 to adjust an additional item, or press “Cancel”
on the remote control or the projector cabinet to quit the menu
display.
E–25
MENU Tree
Basic/ Advanced Menu
Sub Menu
(all)
(all)
(VCH)
(VCH)
(V)
Items
(all)
(all)
Hi-Bright/ Eco
(all)
Normal/ Natural1/ Natural2
(VCH)
(VCH)
(CH)
(all)
Aspect Ratio
Noise Reduction
Color Matrix
White Balance
Auto Adjust
Normal/ Zoom/ Wide Zoom/ Cinema
(all)
(all)
Off/ Low/ Medium/ High
HDTV/ SDTV/ B-Y/R-Y, Cb/Cr, Pb/Pr
Brightness R/G/B, Contrast R/G/B
On/ Off
(R)
(RH)/(R)
(R)
Position/ Clock
Resolution
Horizontal/ Vertical/ Clock/ Phase
Auto/ Native
All Data/ Current Signal
Menu Mode
Basic/ Advanced
English/ German/ French/ Italian/ Spanish/ Swedish/ Japanese
Pointer 1–8
Source Display
On/ Off
Volume Bar (Direct Button)
On/ Off
Menu Display Time
Manual/ Auto 3sec/ Auto 10sec/ Auto 30sec
Signal Select
RGB
VIDEO/ S-VIDEO
Auto/ RGB/ Component
Auto/ NTSC3.58/ NTSC4.43/ PAL/
PAL60/ SECAM
On/ Off
On/ Off
On/ Off
On/ Off
Auto Start
Power Management
Power Off Confirmation
Keystone Save
Clear Lamp Hour Meter
Front/ Floor, Rear/Ceiling, Rear/Floor.
Front/Ceiling
Orientation
Background
Blue/ Black/ Logo
Source Name
Input Terminal
Resolution
Aspect Ratio
Horizontal Frequency Gamma Correction
NOTE:
Adjustable sources
R=RGB
C=Component
All=All sources
Vertical Frequency
Sync Polarity
Signal Type
Video Type
Noise Reduction
Color Matrix
Matrix Type
Lamp Hour Meter
Projector Usage
V=Video/S-Video
H=HDTV
Sync Type
Interlace
E–26
Menu Elements
Tab
Title bar
Highlight
OK Button
Cancel Button
Solid triangle
Check box
Radio button
Slide bar
Menu windows or dialog boxes typically have the following elements:
Title bar:
Indicates the menu title.
Highlight:
Solid triangle:
Tab:
Indicates the selected menu or item.
Indicates further choices are available. A highlighted triangle indicates the item is active.
Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Use this round button to select an option in a dialog box.
Radio button:
Check box:
Slide bar:
Place a checkmark in the square box to turn the option On.
Indicates settings or the direction of adjustment.
OK button:
Cancel button:
Press to confirm your setting. You will return to the previous menu.
Press to cancel your setting. You will return to the previous menu.
E–27
Volume
Menu Descriptions & Functions
Adjusts the sound level of the projector.
Source Select
NOTE:You can display the volume bar without opening the menu.See
"Volume Bar (Direct Button)"on page E-31 for more details.
Image Options
Advanced Mode
Basic Mode
Enables you to select a video source such as a VCR, DVD player,
laser disc player, computer or document camera depending on what
is connected to your inputs. Press the “Select” button on the projec-
tor cabinet or ▲▼ buttons on your remote control to highlight the
menu for the item you want to adjust.
RGB
Selects the computer connected to your RGB or component signal.
NOTE: An optional component cable (Component V cable) is needed
for a component signal.
Video
Provides optional controls such as Keystone Correction, Color Tem-
perature and Lamp Mode. When you select Advanced Mode, the fol-
lowing options are available: Gamma Correction,Aspect Ratio, Noise
Reduction, Color Matrix, White Balance,AutoAdjust, Position/Clock,
Resolution, and Factory Default.
Selects what is connected to yourVideo input-VCR, laser disc player,
DVD player or document camera.
S-Video
Selects what is connected to your S-Video input-VCR, DVD player,
or laser disc player.
Keystone
NOTE: A frame may freeze for a brief period of time when a video is
played back in fast-forward or fast-rewind with a Video or S-Video
source.
This feature corrects the keystone (trapezoidal) distortion to make
the top of the screen longer or shorter to be the same as the bottom.
Use the ᮤ or ᮣ buttons on the slide bar to correct the keystone
(trapezoidal) distortion.
Picture
Keystone distortion
Normal
Provides access to controls for your image. Use the “Select” button
on the projector cabinet or the remote control to highlight the menu
for the item you want to adjust.
NOTE: The maximum keystone angle that can be corrected is 15
degrees upward and downward with the projector placed horizon-
tally. However, a picture will be blurred if you correct the keystone
angle beyond +12 degrees or more for SXGA signal on VT440.
Brightness
Adjusts the brightness level or the back raster intensity.
Contrast
Color Temperature
Adjusts the intensity of the image according to the incoming signal.
Color
Increases or decreases the color saturation level (not valid for RGB).
Hue
Varies the color level from +/- green to +/-blue. The red level is used
as reference. This adjustment is only valid for Video and Component
This feature adjusts the color temperature using the slide bar.
Move the slide bar to the right to increase the color temperature for a
bluish image; to the left to decrease it for a reddish image.
inputs (Not RGB).
Sharpness
Controls the detail of the image for Video (Not for RGB and Compo-
nent).
E–28
Lamp Mode
Aspect Ratio
This feature enables you to select two brightness mode of the lamp:
High-Bright and Eco modes. The lamp life can be extended up to
3000 hours by using the Eco mode.
Aspect Ratio allows you to select the best Aspect mode to display
your source image.
When 4:3 is selected from the source (i.e. DVD player), the fol-
lowing selections will display:
High-Brigh Mode: This is the default setting.
Eco Mode:
Select this mode to increase the lamp life.
Normal
Zoom
Wide Zoom
Cinema
NOTE: If you have selected the Eco mode, the lamp lights in High-
Bright mode for 3 minutes after the projector is turned on. After 3
minutes the lamp will change to Eco mode.
Gamma Correction (Advanced mode)
A-Standard
4:3 Aspect
B-All 4 sides
stretched
C-Left & Right
stretched
D-Left and right
stretched
When Anamorphic or 16:9 is selected from the source (i.e. DVD
player), the following selections will display:
Normal
Zoom
Wide Zoom
Cinema
Use the ᮤ or ᮣ buttons to choose “Normal” when in a lighted
room and “Natural 1&2” when in a darkened room. “Natural 1”
for better flesh tone; “Natural 2” for true reproduction of middle
tones.
Each mode is recommended for :
A-16:9 image
displayed
in 4:3 mode
B- All 4 sides
stretched
C- Left & right
stretched
D- Left and right
stretched to
display the true
aspect
Normal: the regular picture
Natural 1: true color reproduction of natural tones
Natural 2: dark portions of a picture
NOTE: Aspect Ratio is not available for “RGB”.
Advanced Options (Advanced mode)
Allows for adjustments of image position and stability.
Noise Reduction:
You can select three levels video noise reduction.
NOTE: The lower the Noise Reduction level, the better the im-
age quality by way of higher video bandwidth.
Color Matrix
When you select Advanced Options in Advanced mode, the follow-
ing options are available: Aspect Ratio, Noise Reduction, Color Ma-
trix, White Balance, Auto Adjust, Position/Clock, Resolution, and
Factory Default.
First select an appropriate color matrix to fit your component
signal for HDTV or SDTV. Then select an appropriate matrix
type from B-Y/R-Y, Cb/Cr or Pb/Pr.
NOTE: The Color Matrix feature is available for component
video signal only.
E–29
White Balance:
Phase: Use this item to adjust the clock phase or to reduce video
noise, dot interference or cross talk. (This is evident when
part of your image appears to be shimmering.) Use the
ᮤ and ᮣ buttons to adjust the image.
Use “Phase” only after the “Clock” is complete.
This adjustment is made automatically when the Auto
Adjust is turned on.
Resolution (when Auto Adjust is off):
This allows you to adjust the white balance. Brightness for each
color (RGB)is used to adjust the black level of the screen;
Contrast for each color (RGB)to adjust the white level of the
screen.
First use the up or down buttons to select R, G, or B for the bright-
ness and the contrast. Next use the ᮤ or ᮣ buttons to adjust the
level.
This allows you to activate or deactivate theAdvancedAccuBlend
feature.
Auto: Turns on the Advanced AccuBlend feature. The projec-
tor automatically reduces or enlarges the current image
to fit the full screen.
Native: Turns off the Advanced AccuBlend feature. The projec-
tor displays the current image in its true resolution.
Auto Adjust:
NOTE: While you are displaying an image with higher resolu-
tion than the projector's native resolution, even when you are in
the Native mode, the image is displayed full screen using the
Advanced AccuBlend feature.
When “Auto Adjust” is set to “On”, the projector automatically
determines the best resolution for the current RGB input signal
to project an image using NEC’s Advanced AccuBlend Intelli-
gent Pixel Blending Technology.
The image can be automatically adjusted for geometry and sta-
bility; “Horizontal Position”, “Vertical Position”, “Clock” and
“Phase”.
Factory Default (Advanced mode)
On:
Automatically adjusts image “Horizontal Position”, “Ver-
tical Position”, “Clock” and “Phase”.
Off:
User can adjust the image display functions (“Horizontal
Position”, “Vertical Position”, “Clock” and “Phase”)
manually.
Position/ Clock (when Auto Adjust is off)
Changes all adjustments and setting to the factory preset for each
source individually except Lamp Usage Hours. (To reset the lamp
usage time, see “Clear Lamp Hour Meter” on page E-32.)
All Data:
Reset all the adjustments and settings for all
the signals to the factory preset.
Current Signal:
Resets the adjustments for the current signal to
the factory preset levels.
This allows you to manually adjust the image horizontally and
vertically, and adjust Clock and Phase.
The items that can be reset are: Picture, Color Temperature, Gamma
Correction, Aspect Ratio, Noise Reduction, Color Matrix, White
Balance, Position/Clock and Resolution.
Horizontal/Vertical Position:
Adjusts the image location horizontally and vertically
using the ᮤ and ᮣ buttons.
This adjustment is made automatically when the Auto
Adjust is turned on.
Clock: Use this item with the “Auto Adjust off” to fine tune the
computer image or to remove any vertical banding that
might appear. This function adjusts the clock frequen-
cies that eliminate the horizontal banding in the image.
Press the ᮤ and ᮣ buttons until the banding disappears.
This adjustment may be necessary when you connect your
computer for the first time. This adjustment is made au-
tomatically when the Auto Adjust is turned on.
E–30
Menu
Menu Display Time (Advanced mode):
This option allows you to select how long the projector waits
after the last touch of a button to turn off the menu.
The preset choices are "Manual", "Auto 3 sec", "Auto 10 sec",
and "Auto 30 sec". The "Auto 30 sec" is the factory preset.
Manual............The menu can be turned off manually.
Auto 3 sec.......The menu will automatically be turned off in 3
seconds if no buttons are pressed within 3 sec-
onds.
Auto 10 sec.....The menu will automatically be turned off in 10
seconds if no buttons are pressed within 10 sec-
onds.
Auto 30 sec.....The menu will automatically be turned off in 30
seconds if no buttons are pressed within 30 sec-
onds.
Allows you to set preferences for the on-screen menu.
Setup
Menu Mode:
Enables you to set operating options.
Press “OK” to save your changes for all the features of Page1, Page2,
and Page3.
This feature allows you to select two menu modes: one has basic
functionality and the other more advanced functionality.
Basic Mode........... This is the normal mode.
Advanced Mode ... This mode is used for advanced users. In this
mode you can change the following settings:
Gamma Correction, Aspect Ratio, Noise Re-
duction, Color Matrix, White Balance, Auto
Adjust, Position/Clock, Resolution, Factory
Default, Menu Display Time, Signal Select,
Auto Start, Power Management, Power Off
Confirmation and Keystone Save and Clear
Lamp Hour Meter.
[Page1]
Language:
You can choose one of seven languages for on-screen instruc-
tions. The options are: English, German, French, Italian, Span-
ish, Swedish and Japanese.
Projector Pointer:
This enables you to select from eight different Pointer icons for
the “Pointer” button on your remote control.
Orientation:
After moving your Pointer icon to the area you want on the screen,
press the Magnify button on the remote control to enlarge the
selected area on the screen. See page E-24 for more details.
This reorients your image for your type of projection.
The options are:front floor projection, rear ceiling projection, rear
floor projection, and front ceiling projection.
Background:
Use this feature to display a black/ blue screen or logo when no
signal is available.
NOTE: There may be cases where the Pointer function is not avail-
able (ex. a non-interlace signal at 15kHz such as video game.)
Source Display:
You can turn on and off the information for input name such as
VIDEO and RGB.
When this option is on, the current input will be displayed each
time you switch sources or turn on the projector.
Volume Bar (Direct Button):
This option turns on or off the volume bar when you adjust the
sound volume using VOL+/-(up and down) button.
On ...................You can increase or decrease the sound volume
with the volume bar on screen.
Off ..................You can increase or decrease the sound volume
without having to use the volume bar.
E–31
[Page2] (Advanced mode)
Power Off Confirmation:
This option determines whether a confirmation dialog for turn-
ing off the projector will appear or not.
Keystone Save:
This option enables you to save your current keystone settings.
Saving your change once affects all sources. The changes are
saved when you turn off the projector.
Clear Lamp Hour Meter:
Resets the lamp clock back to zero. Pressing this button displays
the “Are you sure?” confirmation dialog box. To reset the lamp
usage hour meter, press “OK”.
NOTE: The projector will turn off and go into standby mode after 2100
hours (up to 3150 hours in Eco mode) of service. If this happens, press
the “Help” button on the remote control for ten seconds to reset the
lamp clock back to zero. Do this only after replacing the lamp.
Signal Select:
<RGB>
Allows you to choose "RGB" for an RGB source such as a com-
puter, or "Component" for a component video source such as a
DVD player. Normally select "Auto" and the projector automati-
cally detects a component signal. However there may be some
component signals that the projector is unable to detect. If this is
the case, select "Component".
Help
Contents
<Video &S-Video System Select>
Provides an online help about how to use the menus. An underlined
link means that you can move to an adjustment item directly. Select-
ing the underlined link and pressing ENTER moves to the correspond-
ing adjustment item.
This feature enables you to select composite video standards
manually. Normally select "Auto".
When you select the video standard for Video and S-Video sepa-
rately, first select the radio button and then select the video stan-
dard from the pull-down menu.
Information
This must be done for Video and S-Video respectively.
Displays the status of the current signal and lamp usage. This dialog
box has four pages. The information included are as follows:
[Page 3] (Advanced mode)
[Page 1]
[Page 3]
Source Name
Aspect Ratio
Gamma Correction
Noise Reduction
Color Matrix
Matrix Type
Input Terminal
Horizontal Frequency
Vertical Frequency
Sync Polarity
[Page 2]
[Page 4]
Signal Type
Video Type
Sync Type
Interlace
Lamp Hour Meter
Projector Usage
Resolution
NOTE:The progress indicator shows the percentage of remaining
bulb life.The value informs you of the amount of lamp and projector
usage respectively.
Auto Start:
Turns the projector on automatically when the power cable is
inserted into an active power outlet. This eliminates the need to
always use the “Power” button on the remote control or projector
cabinet.
Power Management:
When this option is on and there is no RGB input for five min-
utes or more, the projector will automatically turn itself off.
NOTE:This feature does not work with Video or S-Video sources.
E–32
4. MAINTENANCE
This section describes the simple maintenance procedures you should
follow to replace the lamp, clean the filter, and replace the batteries
in the remote control.
3. Insert a new lamp housing until the lamp housing is plugged into
the socket.
CAUTION: Do not use a lamp other than the NEC replace-
ment lamp (VT40LP).
Order this from your NEC dealer.
Replacing the Lamp
After your lamp has been operating for 2000 hours (up to 3000 hours
in Eco mode) or longer, the “Status” light in the cabinet will go on
and the message will appear. Even though the lamp may still be work-
ing, replace it at 2000 (up to 3000 hours in Eco mode) hours to main-
tain optimal projector performance.
Secure it in place with the two screws.
Be sure to tighten the screws.
CAUTION
1
• DO NOT TOUCH THE LAMP immediately after it has been
used. It will be extremely hot. Turn the projector off, wait a
full minute, and then disconnect the power cable. Allow at
least one hour for the lamp to cool before handling.
• DO NOT REMOVE ANY SCREWS except the lamp cover
screw and three lamp case screws. You could receive an elec-
tric shock.
ADJUST
AUTO
U
N
E
M
CE
L
E
C
SELECT
AN
C
OFF
/
R
E
N
T
E
ON
STATUS
POWER
ADJUST
O
SOURCE
E
•
The projector will turn off and go into stand by mode after 2100
(up to 3150 hours in Eco mode) hours of service. If this happens,
be sure to replace the lamp. If you continue to use the lamp after
2000 hours (up to 3150 hours in Eco mode) of use, the lamp bulb
may shatter, and pieces of glass may be scattered in the lamp
case. Do not touch them as the pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
C
2
SELECT
AN
C
R
E
N
T
E
STATUS
POWER
4. Reattach the lamp cover.
Tighten the lamp cover screw.
Be sure to tighten the screw.
To replace the lamp:
1. Loosen the lamp cover screw until the screwdriver goes into a
freewheeling condition and remove the lamp cover. The lamp cover
screw is not removable.
ADJUST
AUTO
M
L
E
M
RC
C
SELECT
SOU
AN
L
E
C
C
SELECT
SOURC
AN
OFF
/
E
R
T
E
C
E
N
C
ON
SELECT
AN
C
R
E
N
T
E
R
E
N
T
E
STATUS
POWER
1
STATUS
POWER
2
M
SOURCE
E
C
SELECT
AN
C
OFF
/
R
E
N
T
E
ON
STATUS
POWER
2
1
2. Loosen the two screws securing the lamp housing until the screw-
driver goes into a freewheeling condition. The two screws are not
removable.
3
Remove the lamp housing by pulling out the handle.
5. After you install a new lamp, select [Advanced Menu] →
[Setup]→[Page 3]→[Clear Lamp Hour Meter] to reset the lamp
usage hours.
NOTE: There is an interlock on this case to prevent the risk of
electrical shock. Do not attempt to circumvent this interlock.
Interlock
ADJUST
AUTO
U
N
NOTE: When the lamp exceeds 2100 hours (up to 3150 hours in Eco
mode) of service, the projector cannot turn on and the menu is not
displayed. If this happens, press the Help button on the remote con-
trol for a minimum of 10 seconds while in standby mode. When the
lamp time clock is reset to zero, the STATUS indicator goes out.
E
M
SOURCE
L
E
C
1
SELECT
AN
C
OFF
/
R
E
N
T
E
ON
STATUS
POWER
2
ADJUST
AUTO
U
N
E
M
E
C
SELECT
AN
C
R
E
N
T
E
STATUS
POWER
E–33
Remote Control Battery Installation
Cleaning or Replacing the Filters
[Wireless Card Remote Control]
The air-filter sponge keeps the inside of the MultiSyncVT440/VT540
Projector free from dust or dirt and should be cleaned after every 100
hours of operation (more often in dusty conditions). If the filter is
dirty or clogged, your projector may overheat.
1. Press firmly and slide the battery cover off.
CAUTION
• Turn off the power and unplug the projector before re-
placing the filter.
• Only clean the outside of the filter cover with a vacuum
cleaner.
• Do not attempt to operate the projector without a filter
cover.
2. Remove the old Lithium coin cell and install new one (CR2025).
Ensure that the side with a “+” is facing up.
• Your projector will not operate unless the filter cover is
installed correctly.
H
N
A
P
A
S
T
M
L
CR202O
V
3
5
nO
2
-
LiC
E
L
L
To clean the air-filter:
Vacuum the filter-through the filter cover.
N
S E L E C T
C
E
L
S O U R C E
M
E
N
U
A U T O
A D J U S T
3. Put the cover back.
RGB
INPUT
AUD
OUTPUT
IN
PC-CO
OUT
S-VIDEO
VD
H
N
A
P
A
S
T
L
CR202O
V
3
5
O
2
-
LiC
E
L
L
To replace the air-filter:
1. Remove the filter cover by pushing up on the catch of the cover
until you feel it detach.
P O W E R
S T A T U S
O N
O F F
E T N E
/
R
C
A
N
S E L E C T
C
E
L
S O U R C E
M
E
N
U
A U T O
A D J U S T
RGB
INPUT
AUD
OUTPUT
2
IN
PC-CO
OUT
1
S-VIDEO
2
1
N
S E L E C T
C
E
L
S O U R C E
M
E
N
U
A U T O
A D J U S T
1
1
RGB
INPUT
AUD
OUTPUT
IN
PC-C
OUT
2
S-VIDEO
VD
2
2. Reinstall the new filter cover.
NOTE: Do not detach the sponge from the filter cover. Do not wash
the filter cover with soap and water. Soap and water will damage the
the filter membrane. Before replacing the filter cover, remove dust
and dirt from the projector cabinet. Keep out dust and during filter
replacement.
E–34
5. TROUBLESHOOTING
This section helps you resolve problems you may encounter while setting up or using the projector.
Power/ Status Light Messages
Condition
Power Indicator Status Indicator
Note
Standby
Steady orange
Blinking green
Steady green
Steady green
–
–
Cooling down
–
Blinks green for 30 seconds
Lamp in High-Bright mode
Lamp in Eco mode
–
–
–
Steady green
One minute after lamp is turned on
Blinking green No light in High-Bright mode The message“Please wait a little”appears
Blinking green in Eco mode
Retrying to turn on lamp
Blinking green Blinking orange
The projector retries 3 times at an inter-
val of 15 sec for max. 45 sec)
3 minutes after lamp is turned on in
Eco mode
Steady green
Steady green
Blinking green
Fixed at High-Bright mode. Lamp mode
can be changed on the menu
Lamp has reached its end of life
(2000 hours or over)
Steady red (High-Bright mode)/ Message appears on screen during 2000-
Steady orange (Eco mode)
2100 hours of lamp usage. The projector
reaches its end of life. Please replace the
lamp as soon as possible
Lamp life has reached its end of life
(2100 hours or over)
Steady orange Steady red
The projector is in standby mode and can-
not be turned on.
Lamp or filter cover error (3 locations)
Steady orange Blinking red (1 sec interval)
Steady orange Blinking red (8 sec interval)
Steady orange Blinking red (12 sec interval)
Steady orange Blinking red (4 sec interval)
The projector is in standby mode and can-
not be turned on.
Fan error
The projector is in standby mode and can-
not be turned on.
Lamp error
The projector is in standby mode and can-
not be turned on.
Temperature error
The projector is in standby mode and can-
not be turned on.
Common Problems & Solutions
Problem
Check These Items
Does not turn on
• Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on.
• Ensure that the lamp cover is installed correctly. See page E-33.
• Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (3150 hours in Eco
mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is particu-
larly warm, move the projector to a cooler location.
No picture
• Use the menu to select your source (Video, S-Video or RGB). See page E-28.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page E-28.
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the Factory Default on the Image Options
Menu in Advanced mode. See page E-30.
Image isn’t square to the
screen
• Reposition the projector to improve its angle to the screen. See page E-14.
• Use the Keystone on the Image Options Menu to correct the trapezoid distortion. See page E-28
Picture is blurred
• Adjust the focus. See page E-24.
• Reposition the projector to improve its angle to the screen. See page E-14.
• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See
page E-15.
Image is scrolling vertically,
horizontally or both
• Use menus or Source button on the remote control or the cabinet to select the source you want to input.
Remote control does not
work
• Install a new battery. See page E-34.
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. See page E-13.
Status indicator is lit or blink-
ing
• See the Power/ Status Light messages above.
Cross color in RGB mode
• If Auto Adjust is off, turn it on.If Auto Adjust is on, turn it off and balance the image with the Position and Clock
Adjust on the Advanced Options Menu. See page E-30.
E–35
6. SPECIFICATIONS
This section provides technical information about the MultiSync VT440/VT540 Projector’s performance.
Model Number
VT440 / VT440G / VT540 / VT540G
Optical
LCD Panel
Lens
0.9” p-Si TFT active-matrix, 800
ן 600 dots (VT440) / 1024ן 768 dots (VT540) Manual zoom, manual focus
F2.0 – 2.3 f=35.8 – 43.0 mm
Lamp
160W NSH lamp (130W in Eco mode)
25 – 300 inches (0.64 – 7.62 m) diagonal
3.94 – 39.04 ft (1.2 - 12.0 m)
Image Size
Projection Distance
Electrical
Inputs
Video (NTSC / PAL / PAL60 / SECAM / NTSC4.43)
Horizontal Frequency : 15 – 100 kHz (RGB : 24 kHz or over)
Vertical Frequency : 50 – 117 Hz
Video Bandwidth
Color
RGB: 80 MHz
Reproduction Full color, 16.7 million colors simultaneously.
550 TV lines : NTSC / PAL / NTSC4.43 / YCbCr
350 TV lines : SECAM
Horizontal Resolution
RGB VT440 : 800 dots horizontal, 600 dots vertical
VT540 : 1024 dots horizontal, 768 dots vertical
100 – 120 / 200 – 240 VAC, 50 / 60 Hz
Power Requirement
Input Current
Power Consumption
2.7 A (100 – 120 VAC) / 1.3A (200 – 240 VAC)
240 W (205 W in Eco mode)
Mechanical
Dimensions
Net Weight
9.57" (W)
ן 4.0" (H)ן 11.2" (D) / 243 mm (W)ן 103 mm (H)ן 284 mm (D) (not including lens) 8.8 lbs / 3.9 kg
Environmental Considerations Operational Temperatures: 32˚ – 95˚F (0˚ to 35˚C), 20 – 80% humidity
Storage Temperatures: 14˚ – 122˚F (-10˚ to 50˚C), 30 – 85% humidity
Regulations
UL Approved (UL 1950, CSA 950)
Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Meets AS/NZS3548 Class B
Meets EMC Directive (EN55022, EN55082-1, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950, TUV GS Approved)
We provides more information about our projectors through the World Wide Web at http://www.nec-pj.com/
The specifications are subject to change without notice.
E–36
TROUBLESHOOTING
Operational checks
By making checks on operation under normal working conditions, a certain degree of fault diagnosis can be
carried out. Prior to removing the top cover, make the following checks:
• Is the POWER indicator lit in orange color in the standby state?
NO
• The POWER cord is disconnected.
• Problem in the power supply.
• The cable (POPM) is disconnected.
• Fuses (F3100 to F3104) of the MAIN PWB have blown out.
• Failure in the CPU peripheral circuits of the MAIN PWB.
• Clogging around the air filter.
• Deviation from the working range and the temperature-condition range.
•The cable (bimetal) is disconnected.
YES
▼
• Is the STATUS indicator flashing?
YES • The lamp fails to light.
[Flashing at the intervals of once every 12 seconds (6-second ON/6-second OFF)]
• The filter cover or the lamp cover is dislodged.
[Flashing at the intervals of 1 second (0.5-second ON/0.5-second OFF)]
• The fan is stopped due to the fan being out of order or intrusion of foreign substance.
[Flashing at the intervals of once every 8 seconds (4-second ON/4-second OFF)]
• The cable (POLM) is disconnected.
[Flashing at the intervals of once every 12 seconds (6-second ON/6-second OFF)]
• The cables (POF1, POF2) are disconnected.
[Flashing at the intervals of once every 8 seconds (4-second ON/4-second OFF)]
• The cable (POMK) is disconnected.
[Flashing at the intervals of 1 second (0.5-second ON/0.5-second OFF)]
• Lamp is out of order.
[Flashing at the intervals of once every 12 seconds (6-second ON/6-second OFF)]
▼
NO
• Is the STATUS indicator lit?
YES
• The total lamp lighting time has exceeded 2000 hours, or the data are destroyed.
NO
▼
• Is the POWER indicator lit in green with POWER ON?
YES • The lamp’s life has expired. (The STATUS indicator is lit in red.)
• Failure in I/O PWB and MAIN PWB.
• The cables (POMI, POXV, POXT, PORX, POGX, POBX) are disconnected.
• The LC panel is out of order.
▼
NO
• Peripheral circuits are out of order around the cabinet switch, remote control, remote control light receiver, and
CPU.
4-1
TROUBLESHOOTING
POWER block
Problems in the POWER and related circuits often cause typical malfunctions, such as no picture presentation,
no power supply to each PWB, no lamp lighting, no fan rotation, and so on.
Confirm whether the voltage outputs specified below are available at the POPM connector of the MAIN PWB.
PIN No.
Signal name
PS_PW
GND
Standby
0V
Power ON
+3.3V
GND
Related circuits
1
2
POWER ON/OFF control signal (output from MAIN)
GND
+17.5V
GND
0V
GND
3
A+17.5V
GND
+17.5V
GND
LC driver system
4
GND
5
A+12V
A+12V
GND
+12V
+12V
GND
Input signal processor system, VIDEO signal processor system
6
0V
Fan control
7
GND
GND
+5V
GND
8
GND
GND
GND
9
S+5V
+5V
A/D, ENDEAVOR
10
11
12
13
14
15
S+5V
+5V
+5V
Same as above
GND
GND
GND
+3.3V
+3.3V
GND
GND
GND
GND
GND
GND
S+3.3V
S+3.3V
GND
+3.3V
+3.3V
GND
A/D, YAMAG, UNI2, CPU, and CPU peripheral
Same as above
GND
4-2
TROUBLESHOOTING
LCES PWB
Are the following signal inputs available at POSV (connected with POSV of the MAIN PWB)?
(See the waveform diagram.)
PIN No.
• 9-14 : Rch video signal (10Vp-p)
• 22-27 : Gch video signal (10Vp-p)
• 35-40 : Bch video signal (10Vp-p)
NO
POSV connector defective
YES
▼
Are the following signal outputs available at the respective output pins and test pins of IC5201
(or IC5202, IC5203)? (See the waveform diagram.)
PIN No.
• 27
: Y shift register start pulse (DY)
• 28-29 : Y shift register transfer clock (CLY, CLYB)
• 30-31 : X shift register transfer clock (CLX, CLXB)
• 32
: X shift register start pulse (DX)
• 33-34 : X driver driving direction changeover (DIRX, DIRXB)
• 35-36 : Enable pulse
• 37
: Pre-charge pulse (NRG)
• 38-39 : Y driver driving direction changeover (DIRY, DIRYB)
• TP5201, TP5202, TP5203, TP5204, TP5205, TP5206
Pre-charge level (NRS1R, NRS2R, NRS1G, NRS2G, NRS1B, NRS2B)
• TP5207, TP5209, TP5211
Panel’s opposing electrode potentia (LCCOMR, LCCOMG, LCCOMB)
NO
POST connector defective, or failure in the MAIN PWB or LCES PWB
YES
▼
Failure in the LC panel, or other LCES PWB malfunction (defective soldering, cracks in PWB)
4-3
TROUBLESHOOTING
LCEX PWB
Are the following signal inputs available at POSV (connected with POSV of the MAIN PWB)?
(See the waveform diagram.)
PIN No.
• 3-14 : Rch video signal (10Vp-p)
• 16-27 : Gch video signal (10Vp-p)
• 29-40 : Bch video signal (10Vp-p)
NO
POSV connector defective
YES
▼
Are the following signal outputs available at the respective output pins and test pins of IC6201
(or IC6202, IC6203)? (See the waveform diagram.)
PIN No.
• 27
: Y shift register start pulse (DY)
• 28-29 : Y shift register transfer clock (CLY, CLYB)
• 30-31 : X shift register transfer clock (CLX, CLXB)
• 32
: X shift register start pulse (DX)
• 33-34 : X driver driving direction changeover (DIRX, DIRXB)
• 35-36 : Enable pulse
• 37
: Pre-charge pulse (NRG)
• 38-39 : Y driver driving direction changeover (DIRY, DIRYB)
• TP6201, TP6202, TP6203
Pre-charge level (NRS1R, NRS1G, NRS1B)
• TP6204, TP6206, TP6208
• Panel’s opposing electrode potential (LCCOMR, LCCOMG, LCCOMB)
NO
POST connector defective, or failure in the MAIN PWB or LCES PWB
YES
▼
Failure in the LC panel, or other LCES PWB malfunction (defective soldering, cracks in PWB)
4-4
TROUBLESHOOTING
• Troubleshooting for the I/O block, Sync block, and Video block
1. No video images are generated. (VIDEO system)
1
2
3
4
Are there signals (Y, R-Y, B-Y) at L3401 to 3? See the relevant circuit diagram for waveforms.
YES Check Q3401 to 3, IC3401, and the peripheral circuits.
NO
Are there signals at Pins 30 to 32 of IC1104?
YES Check Q1115 to 7 and the peripheral circuits.
▼
NO
▼
Is the input signal for S VIDEO?
11
YES
To
.
NO
▼
Is the input signal for SECAM or B/W?
9
YES
To
.
NO
5 Are there signals at Pin 9 (Y: 2Vp-p) and Pin 7 (C) of IC1104?
YES
Check the power supply of IC1104, I2C bus, and the peripheral circuits.
▼
NO
Are there signals at Pin 23 (Signal C) and Pin 25 (Signal Y) of IC1101?
YES Check FL1114 to 5, Q1104 to 1109, and the peripheral circuits.
▼
6
NO
7 Is there a video signal at Pin 3 of IC1101? (1.4Vp-p)
YES Check the power supply of IC1101, the FSC (chroma frequency) signal at
Pin 19, and the peripheral circuits.
▼
NO
Is there a video signal at Pin 6 of IC1104? (2.0Vp-p)
YES Check Q1101 and the peripheral circuits.
▼
8
NO
Is there a video signal at Pin 41 of IC1104? (1.0Vp-p)
YES
Check the power supply of IC1104, I2C bus, and the peripheral circuits.
▼
9
NO
▼
10
Is there a video signal input in CV at Pin 20 of POMI? (1.0Vp-p)
NO
Check the POMI connector, poor soldering in I/O PWB, and the signal cable.
Check Q1005, IC1100, FL1113, and the peripheral circuits.
YES
11
Are there signals at Pin 4 (Y: 1Vp-p) and Pin 2 (C) of IC1104?
YES
Check the power supply of IC1104, I2C bus, and the peripheral circuits.
NO
▼
1
2
Are there video signal inputs at Pin 18 (Y) and Pin 16 (C) of POMI?
NO
Check the POMI connector, poor soldering in I/O PWB, and the signal cable.
Check Q1006, Q1107, and the peripheral circuits.
YES
4-5
TROUBLESHOOTING
2. No RGB images are generated. (VIDEO system)
1
Are there video signals (R, G, B/Y, Cb, Cr) at TP3403 to 5?
YES Check IC3401 and the peripheral circuits.
NO
▼
2
Are there video signal inputs at Pin 30 (R), Pin 28 (G), and Pin 26 (B) of POMI?
NO
Check the POMI connector, poor soldering in I/O PWB, and the signal cable.
Check Q1020 to 4 and the peripheral circuits.
YES
3. No images are generated. (Sync system)
1
2
3
4
Is there a horizontal sync signal (in positive polarity) at TP3503?
1
2
YES
To
.
NO
Is there a horizontal sync signal (in positive polarity) at Pin 111 of IC3401?
YES Check IC3401 and the peripheral circuits.
▼
NO
Is the input signal for VIDEO or DVD?
YES To 7 .
▼
NO
Is there a horizontal sync signal (in positive polarity) at Pin 83 of IC3301?
YES Check IC3301 and the peripheral circuits.
▼
NO
5 Are there signals at Pin 4 (SOG), Pin 6 (H), and Pin 8 (V) of IC1006?
YES Check IC1006 and the peripheral circuits.
▼
NO
▼
6
Are there signal inputs at Pin 28 (SOG), Pin 24 (H), and Pin 22 (V) of POMI?
NO
Check the POMI connector, poor soldering in I/O PWB, and the signal cable.
Check Q1025 to 34, Q1000, Q1013 to 6, and the peripheral circuits.
YES
7 Is there a horizontal sync signal (in positive polarity) at Pin 86 of IC3301?
YES Check IC3301 and the peripheral circuits.
NO
Is there a horizontal sync signal (in positive polarity) at Pin 19 of IC1104?
YES Check IC1106 and the peripheral circuits.
▼
8
9
NO
Are there video signals (sync provided) at Pin 41 (VIDEO) and Pin 43 (DVD) of IC1104?
YES
Check the power supply of IC1104, I2C bus, and the peripheral circuits.
▼
NO
▼
10
Is the input signal for VIDEO?
10
YES
To , No VIDEO images.
▼
NO
4-6
TROUBLESHOOTING
▼
11
Is there a video signal input (sync provided) at Pin 28 (G) of POMI?
NO
Check the POMI connector, poor soldering in I/O PWB, and the signal cable.
Check IC1001, Q1000, and the peripheral circuits.
YES
1
2
Is there a vertical sync signal (in positive polarity) at TP3507?
YES Check IC3502 and the peripheral circuits.
NO
▼
1
2
Is the input signal for VIDEO or DVD?
16
YES
To
.
NO
Is there a vertical sync signal (in positive polarity) at Pin 84 of IC3301?
YES Check IC3301 and the peripheral circuits.
▼
13
NO
Are there signals at Pin 4 (SOG), Pin 6 (H), and Pin 8 (V) of IC1006?
YES Check IC1006 and the peripheral circuits.
▼
14
15
NO
▼
Are there signal inputs at Pin 28 (SOG), Pin 24 (H), and Pin 22 (V) of POMI?
NO
Check the POMI connector, poor soldering in I/O PWB, and the signal cable.
Check Q1025 to 34, Q1000, Q1013 to 6, and the peripheral circuits.
YES
16
Is there a vertical sync signal (in positive polarity) at Pin 87 of IC3301?
YES Check IC3301 and the peripheral circuits.
NO
17 Is there a vertical sync signal (in negative polarity) at Pin 5 of IC1104?
▼
YES
NO
Check Q1110 to 1 and the peripheral circuits.
9
To
.
4. No sound generation
1
2
3
Are there audio signals at Pins 48 and 56 of IC4100?
YES Check the speaker, connector, and the peripheral circuits.
NO
Is there an audio signal at Pin 9 of IC4100?
YES Check IC4100, VOL voltage at Pin 28, and the peripheral circuits.
▼
NO
▼
Is there a signal input at Pin 14 (AUDIO) of POMI?
NO
Check the POMI connector, poor soldering in I/O PWB, and the signal cable.
Check Q1011, ST connector, and the peripheral circuits.
YES
4-7
METHOD OF ADJUSTMENTS
PC Control Software
Table of Contents
1. Outline software descriptions
2. Equipment to be used and operating environments
3. Troubleshooting and adjustment procedures
3-1. Replacement of the MAIN PWB
3-2. Replacement of the LCEP PWB
3-3. Replacement of the VIDEO-DEC PWB
3-4. Replacement of the LCD panel
4. Various functional descriptions
4-1. Data
4-2. Sub-B/C
4-3. Flicker
4-4. Ghost
4-5. Lamp
4-6. Option
5. Error messages
5-1
METHOD OF ADJUSTMENTS
1. Outline software descriptions
This is the PC control software for servicing adjustments to be conducted during the replacement of the MAIN
PWB, LCEP PWB, VIDEO-DEC PWB, or the LCD panel for the LCD projector, the VT440/VT540 Series.
This software is used for the adjustment of Sub-Brightness/Sub-Contrast, Flicker, and Ghost, and also the
modification of Lamp Usage Time, Filter Usage Time, Panel Usage Time, Projector Usage Time, and Language
Selection.
In addition, it enables reading and writing of various data, such as the V-T data for the PJ, the adjusting data for
factory shipment, various data for setting (user), and the logo and uniformity data.
2. Equipment to be used and operating environments
<Equipment to be used>
• Software for servicing adjustments (Ser_99vt.exe Ver1.0)
Attached files: V-T Data, etc.
• Personal computer [Enabled to actuate Windows95 or Windows3.1, and the serial port (COM1 or COM2 or
COM3) is of the D-SUB9pin.]
• Video signal generator [Auto-adjustment type: Enabled to generate an output of NTSC split color bars (7
colors)]
• Component signal generator [Auto-adjustment type: Enabled to generate an output of 15kHz Component
Video 60Hz split color bars (7 colors)]
• Serial cable (Accessory for the PJ main unit)
<Connections>
• Connect the PC CONTROL terminal (Mini DIN-8pin) of the PJ with either serial port COM1 or COM3 (D-SUB
9pin) of the personal computer through a serial cable (accessory for the PJ main unit).
• During the adjustment of RGB Sub-Brightness/Sub-Contrast, connect the RGB terminal of the PJ with an
ANALOG RGB output of the personal computer or an RGB signal generator to be used for adjusting signal
generation.
• During the adjustment of Component Sub-Brightness/Sub-Contrast, connect the RGB terminal of the PJ with
a Component signal generator to be used for adjusting signal generation.
• During the adjustment of Video Sub-Brightness/Sub-Contrast, connect the VIDEO terminal with a Video
signal generator to be used for adjusting signal generation.
<Setting of personal computer that generates adjusting pattern screen outputs>
• Personal computer’s definition, frequency, and the No. of colors
Make settings at VESA XGA (1024x768) 70Hz, high color (16 bits) or above.
• Method of adjusting pattern screen display
Using the [ON] button located in the test pattern box, the adjusting pattern screen can be displayed on the
PC screen. In this case, however, only the test patterns in the [Sub-B/C] tab can be displayed. All other
adjusting patterns are the internally available test patterns.
5-2
METHOD OF ADJUSTMENTS
3. Troubleshooting and adjustment procedures
3-1. Replacement of the MAIN PWB
<Copying of the V-T data, ADJ data, Logo data, and Uniformity data>
Let the PJ power supply stay in the STAND BY state and select the [Data] tab for servicing software.
Make data read/write according to the descriptions (1) and (2) below.
(1) Data Read
Prior to the replacement, and as required, read the presently used data of the MAIN PWB and save
them in the relevant file.
(According to the type of fault, it may be impossible to save these data.)
Designate the file name and save the data by clicking the relevant [Read (PJ->File)] button of the V-T
data, ADJ data, Logo data, and Uniformity data.
(2) Data Write
After the replacement of the MAIN PWB, click the relevant [Write (File->PJ)] button of the V-T data,
ADJ data, Logo data, and Uniformity data to select the saved file, and write the data.
If it is impossible to save the data of the MAIN PWB used before the replacement, write the V-T data
of the model from the file as required, using the [Write (File->PJ)] button of the V-T data.
After all the data have been written, pull out the AC cord of the PJ and confirm that the Power LED is
unlit. Since then, connect the AC cord again.
<Adjustment of Sub-Brightness/Sub-Contrast>
Select the [Sub-B/C] tab for servicing software.
Make the respective adjustments of RGB/Component/Video according to the descriptions (1), (2) and (3)
below.
(1) Adjustment of RGB Sub-Brightness/Sub-Contrast
Select [RGB] in the Auto ADJ box.
Make adjustments by either method of (a) or (b) below.
(a) Auto adjustment
As an adjusting signal, enter an input of Window (Center: White) with the use of an RGB signal
generator. Otherwise, enter an RGB output of the personal computer. (When the PC output is
used in the auto-adjustment mode, the screen is automatically changed over to the Window screen.)
When the [Auto] button is clicked in the Auto ADJ box, automatic adjustment is started.
After the completion of automatic adjustment, confirm that there is no coloring of the gray scale.
If any coloring is perceived, make fine adjustments of (b) by manual adjustment.
Note: It is impossible to carry out normal adjustments if the definition (VESA XGA 70Hz) or the
pattern is improper for the adjusting signal.
(b) Manual adjustment
If the automatic adjustment is impossible, manual adjustments should be carried out.
As an adjusting signal, enter an input of gray scale with the use of an RGB signal generator.
Otherwise, enter an RGB output of the personal computer and display a gray scale with the use of
the [Scale] button in the Test Pattern box.
Use a scroll bar to adjust Sub-Brightness/Sub-Contrast, making sure not to cause black and white
chroma and also coloring in the gray scale.
After the completion of manual adjustment, click the [Set] button in the Data box.
5-3
METHOD OF ADJUSTMENTS
(2) Adjustment of Component Sub-Brightness/Sub-Contrast
Select [Component] in the Auto ADJ box.
Make adjustments by any method of (a), (b) or (c) below.
(a) Auto adjustment
As an adjusting signal, enter a split color bar (7 colors) with the use of a Component signal genera-
tor.
When the [Auto] button is clicked in the Auto ADJ box, automatic adjustment is started.
After the completion of automatic adjustment, confirm that there is no coloring of the gray scale.
If any coloring is perceived, make fine adjustments of (b) by manual adjustment.
Note: It is impossible to carry out normal adjustments if the pattern is improper for the adjusting
signal.
(b) Manual adjustment
If the automatic adjustment is impossible, manual adjustments should be carried out.
As an adjusting signal, enter an input of gray scale with the use of a Component signal generator.
Use a scroll bar to adjust Sub-Brightness/Sub-Contrast, making sure not to cause black and white
chroma and also coloring in the gray scale.
After the completion of manual adjustment, click the [Set] button in the Data box.
(c) Copying of the Video adjusting value
If no Component signal generator is available, try to check [Video-> Comp] in the Auto ADJ box.
Then, the same adjusting value as that for Video is written during the adjustment of Video.
(3) Adjustment of Video Sub-Brightness/Sub-Contrast
Select [Video] in the Auto ADJ box.
Make adjustments by either method of (a) or (b) below.
(a) Auto adjustment
As an adjusting signal, enter an input of split color bar (7 colors) with the use of a Video signal
generator.
When the [Auto] button is clicked in the Auto ADJ box, automatic adjustment is started.
After the completion of automatic adjustment, confirm that there is no coloring of the gray scale.
If any coloring is perceived, make fine adjustments of (b) by manual adjustment.
Note: It is impossible to carry out normal adjustments if the pattern is improper for the adjusting
signal.
(b) Manual adjustment
If the automatic adjustment is impossible, manual adjustments should be carried out.
As an adjusting signal, enter an input of gray scale with the use of a Video signal generator.
Use a scroll bar to adjust Sub-Brightness/Sub-Contrast, making sure not to cause black and white
chroma and also coloring in the gray scale.
After the completion of manual adjustment, click the [Set] button in the Data box.
When the respective adjustments have been finished for RGB/Component/Video, a check mark is
given to the left-end check box in the Auto ADJ box.
<Adjustment of Flicker>
Select the [Flicker] tab for servicing software.
Make the respective adjustments of Floor/Ceiling according to the descriptions (1) and (2) below.
(1) Adjustment of Floor
Check [Floor].
Click the [ON] button in the Test Pattern box in order to display the internal horizontal line signal.
If this [ON] button is clicked continuously, a changeover action takes place in the toggle mode in the
course of R-> G-> B-> R. Make adjustments with the scroll bar so that the flicker in the center part
becomes minimum for each color.
5-4
METHOD OF ADJUSTMENTS
(2) Adjustment of Ceiling
Check [Ceiling].
Click the [ON] button in the Test Pattern box in order to display the internal horizontal line signal.
If this [ON] button is clicked continuously, a changeover action takes place in the toggle mode in the
course of R-> G-> B-> R. Make adjustments with the scroll bar so that the flicker in the center part
becomes minimum for each color.
When adjustments have been finished for both (1) and (2) above, click the [Set] button in the Data box.
Click the [CLS] button in the Test Pattern box in order to clear the internal test signal.
<Adjustment of Ghost>
Select the [Ghost] tab for servicing software.
Click the [ON] button in the Test Pattern box in order to display the internal ghost adjusting signal.
Make adjustments with the scroll bar so that the ghost becomes minimum for each color.
When adjustments have been finished, click the [Set] button in the Data box.
Click the [CLS] button in the Test Pattern box in order to clear the internal test signal.
<Modification of Lamp, Filter, Panel, and Projector Usage Time>
In the case of failure in the <Copying of the V-T data, ADJ data, Logo data, and Uniformity data> to be
carried out in the first place, each usage time must be fixed at “0 hours.” Therefore, make the setting of
each usage time, as required.
Let the PJ power supply stay in the STAND BY state and select the [Lamp] tab for servicing software.
Make the modification of the usage time according to the descriptions (1), (2), and (3) below.
(1) Modification of the lamp usage time
Check [Change time (Lamp Usage Time)] and make the setting of lamp usage time by the use of the
scroll bar.
After the completion of this setting, click the [Set] button.
(2) Modification of the filter usage time
Check [Change time (Filter Usage Time)] and set the lamp usage time using the scroll bar/editor input.
After the completion of this setting, click the [Set] button.
(3) Modification of the panel usage time
Check [Change time (Panel Usage Time)] and set the lamp usage time using the scroll bar/editor
input.
After the completion of this setting, click the [Set] button.
(4) Check [Change time (Projector Usage Time)] and set the lamp usage time using the scroll bar/editor
input.
After the completion of this setting, click the [Set] button.
Upon the completion of (1), (2), (3), and (4) above, pull out the AC cord of the PJ and confirm that the
Power indicator is unlit. Since then, connect the AC cord again.
<Language Setting>
Select the [Lamp] tab for servicing software.
In the case of the domestic (Japan) mode, check [VTxxxJ Model] in the Language box.
In the case of an overseas mode, check [Vtxxx, G, GS Model].
In this unit, the factory data only are rewritten to hold the user setting values for the <Copying of the V-T
data, ADJ data, Logo data, and Uniformity data> to be carried out in the first place. For this reason, there
can be no coincidence between the set language and the displayed language (user setting).
5-5
METHOD OF ADJUSTMENTS
3-2. Replacement of the LCEX (LCES) PWB
<Adjustment of Flicker>
Make the similar adjustments as those for the replacement of the MAIN PWB.
3-3. Replacement of the VIDEO-DEC PWB
<Adjustment of Sub-Brightness/Sub-Contrast>
Make the similar adjustments as those for the replacement of the MAIN PWB.
3-4. Replacement of the LCD panel
<Adjustment of Sub-Brightness/Sub-Contrast>
If there is coloring in the gray scale, carry out fine adjustments manually.
In regard to the method of adjustments, refer to the descriptions about the replacement of the MAIN PWB.
<Adjustment of Flicker>
Make the similar adjustments as those for the replacement of the MAIN PWB.
<Adjustment of Ghost>
Make the similar adjustments as those for the replacement of the MAIN PWB.
<Adjustment of Uniformity>
Make the similar adjustments as those for the replacement of the MAIN PWB.
<Modification of Lamp, Filter, Panel, and Projector Usage Time>
Change the panel usage time to “0 Hours.”
In regard to the method of modification, refer to the descriptions about the replacement of the MAIN PWB.
5-6
METHOD OF ADJUSTMENTS
4. Various functional descriptions
4-1. Data
<Model Name>
The present PJ data are acquired and discrimination of the model is carried out.
In the case of the VT440 System, [VT440] is displayed. For the VT540 System, [VT540] is displayed.
<Read and Write of the V-T Data>
At the time of the replacement of the MAIN PWB, this function is used to write the V-T data, which have been
used before the replacement, in the new MAIN PWB.
The action for reading and writing of the V-T data should be carried out while the PJ power supply is made to
stay in the Standby mode.
When the [Read (PJ-> File)] button in the V-T Data box is clicked under the condition that the MAIN PWB
before replacement is left attached, the Save Dialog is opened. In this state, designate the file name.
The V-T data are read out of the PJ and saved with the specified file name.
The saved file name is displayed below the [Read (PJ-> File)] button.
When the [Write (File-> PJ)] button in the V-T Data box is clicked after the replacement of the MAIN PWB, the
Open Dialog is opened. In this state, select the saved file name.
Write the V-T data in the PJ from the designated file.
The written file name is displayed below the [Write (PJ-> File)] button.
5-7
METHOD OF ADJUSTMENTS
<Read and Write of the ADJ Data>
At the time of the replacement of the MAIN PWB, this function is used to write the V-T data (adjusting data
used for shipment and various user setting values), which have been used before the replacement, in the
new MAIN PWB.
The data rewritten in this case are the factory shipment adjusting data for Sub-Brightness/Sub-Contrast,
Flicker, Ghost, and Uniformity, and also the various data of usage time for the lamp, filter, and panel.
The action for the saving and writing of the ADJ data should be carried out while the PJ power supply is made
to stay in the Standby mode.
When the [Read (PJ-> File)] button in the ADJ Data box is clicked under the condition that the MAIN PWB
before replacement is left attached, the Save Dialog is opened. In this state, designate the file name.
The ADJ data are read out of the PJ and saved with the specified file name.
The saved file name is displayed below the [Read (PJ-> File)] button.
When the [Write (File-> PJ)] button in the ADJ Data box is clicked after the replacement of the MAIN PWB, the
Open Dialog is opened. In this state, select the saved file name.
Write the ADJ data in the PJ from the designated file.
The written file name is displayed below the [Write (PJ-> File)] button.
After the ADJ data have been written, pull out the AC cord of the PJ without fail and confirm that the Power
LED is unlit.
<Read and Write of the Logo Data>
At the time of the replacement of the MAIN PWB, this function is used to write the Logo data (user registra-
tion), which have been used before the replacement, in the new MAIN PWB.
The action for the saving and writing of the Logo data should be carried out while the PJ power supply is
made to stay in the Standby mode.
When the [Read (PJ-> File)] button in the Logo Data box is clicked under the condition that the MAIN PWB
before replacement is left attached, the Save Dialog is opened. In this state, designate the file name.
The Logo data are read out of the PJ and saved with the specified file name.
The saved file name is displayed below the [Read (PJ-> File)] button.
When the [Write (File-> PJ)] button in the Logo Data box is clicked after the replacement of the MAIN PWB,
the Open Dialog is opened. In this state, select the saved file name.
Write the Logo data in the PJ from the designated file.
The written file name is displayed below the [Write (PJ-> File)] button.
<Read and Write of the Uniformity Data>
At the time of the replacement of the MAIN PWB, this function is used to write the Uniformity data, which have
been used before the replacement, in the new MAIN PWB.
The action for the reading and writing of the Uniformity data should be carried out while the PJ power supply
is made to stay in the Standby mode.
When the [Read (PJ-> File)] button in the Uniformity Data box is clicked under the condition that the MAIN
PWB before replacement is left attached, the Save Dialog is opened. In this state, designate the file name.
The Uniformity data are read out of the PJ and saved with the specified file name.
The saved file name is displayed below the [Read (PJ-> File)] button.
When the [Write (File-> PJ)] button in the Uniformity Data box is clicked after the replacement of the MAIN
PWB, the Open Dialog is opened. In this state, select the saved file name.
Write the Uniformity data in the PJ from the designated file.
The written file name is displayed below the [Write (PJ-> File)] button.
Note 1: According to the type of fault, it may be impossible to save the data.
The default data are written in the MAIN PWB in advance.
Note 2: The ADJ data should be written under the condition that the PJ power supply is made to stay in the
standby state. In addition, unless the AC cord of the PJ is drawn out after data writing, the written
data cannot be written in the Flash ROM.
Note 3: When all-data resetting is effected, various user setting values written by ADJ data writing cannot be
held and the factory shipment values are recovered.
5-8
METHOD OF ADJUSTMENTS
4-2. Sub-B/C
<Sub-Brightness/Sub-Contrast>
This function is used for the manual adjustment of Sub-Brightness/Sub-Contrast.
The data are independently possessed by the three types of signals for RGB, Component, and Video. The
signal data selected in the Auto ADJ box are acquired and they are respectively displayed for R(Cr)/G(Y)/
B(Cb) beside the scroll bar on the screen.
The data acquired firstly (at the time of starting of the adjusting software) are stored as the initial value and
displayed on the left of the arrow mark. The present value is displayed on the right of the arrow.
When writing of the ADJ data is conducted with [Data], however, the written data are regarded as the initial
value.
Display the gray scale and make adjustments with the use of the scroll bar, making sure not to cause white
and black chroma and also coloring.
Adjusting range: 00H - FFH
5-9
METHOD OF ADJUSTMENTS
<Auto ADJ>
This function is used for the selection and automatic adjustment of signals to be used for the adjustment of
Sub-Brightness/Sub-Contrast.
Select the required adjusting signal from RGB/Component/Video.
According to the selected signal, signal changeover (RGB/Component-> RGB1, Video-> Video), data read,
and data reset (signal being displayed) are carried out.
When the [Auto] button is clicked, automatic adjustment is carried out for the selected signal.
If a signal generator is used during the automatic adjustment of RGB, setting should be made at Window
(Center: White) at VESA XGA 70Hz. When a PC signal is used, the Window mode is chosen automatically.
For the automatic adjustment of Component, the signal should be set at the split color bar (7 colors).
In case of failure in the adjustment of Component, check [Video-> Comp].
During the adjustment of Video, the same data are copied in Component.
In the case of automatic adjustment, or when the data are written with the use of the [Set] button in the Data
box, a check mark is given to the check box located on the left of the RGB/Component/Video selection as a
mark of the completion of adjustment.
This check mark is cleared when the data are reset with the [Reset] button in the Data box.
<Test Pattern>
This function is used when a personal computer intended for adjustments is used as a signal source.
When the [Window] button is clicked, a window display is presented on the PC screen.
This window is used for the adjustment of RGB, but the preliminary display of this window is not required in
the case of the automatic adjustment since it is automatically displayed.
When the [Scale] button is clicked, a 16-gradation gray scale is displayed on the PC screen.
When a double click is conducted on the test pattern, this double click is cleared.
<Data>
When the [Set] button is clicked, the adjusted values of Sub-Brightness/Sub-Contrast, adjusted with the scroll
bar, are written in the Flash ROM.
In the case of automatic adjustment, it is unnecessary to click the [Set] button since the adjusted values are
automatically written in the Flash ROM.
When the [Reset] button is clicked, the adjusted values of Sub-Brightness/Sub-Contrast are restored to the
initial values (at the time of starting of the adjusting software) and written in the Flash ROM.
Note 1: The data adjusted with the scroll bar are the temporary ones. They are not sustained in the PJ without
taking any measures. Execute [Set] and write the data in the Flash ROM.
Note 2: Since automatic adjustment is conducted by examining the predetermined position in the screen, this
adjustment is impossible to carry out unless the patterns, definition, etc., are found inadequate.
5-10
METHOD OF ADJUSTMENTS
4-3. Flicker
<Floor/Ceiling>
This function is used for the adjustment of flicker.
The data are sustained for Floor and Ceiling, respectively.
The present data of the PJ are acquired and displayed on the screen.
The data acquired firstly (at the time of starting of the adjusting software) are stored as the initial value and
displayed on the left of the arrow mark. The present value is displayed on the right of the arrow.
When writing of the ADJ data is conducted with [Data], however, the written data are regarded as the initial
value.
Select the method of projection for Floor/Ceiling adjustment.
The scroll bar on the selected side becomes adjustable.
Display the Test Pattern, and make adjustments with the scroll bar so that the flicker in the center part
becomes minimum for R/G/B, respectively.
Adjusting range: 00H - FFH
<Test Pattern>
This function is used when an internal Test Pattern is displayed for flicker adjustment.
When the [ON] button is clicked, a horizontal line signal of R is displayed on the projected screen.
If this [ON] button is continuously clicked since then, a changeover action takes place in the toggle mode in
the order of horizontal line signal of G-> horizontal line signal of B-> and horizontal line signal of R.
When the [CLS] button is clicked, the Test Pattern is cleared (input changeover to RGB1).
<Data>
When the [Set] button is clicked, the flicker value adjusted with the scroll bar is written in the Flash ROM.
When the [Reset] button is clicked, the adjusted flicker value is restored to the initial value (at the time of
starting of the adjusting software) and written in the Flash ROM.
Note 1: The data adjusted with the scroll bar are the temporary ones. They are not sustained in the PJ without
taking any measures. Execute [Set] and write the data in the Flash ROM.
5-11
METHOD OF ADJUSTMENTS
4-4. Ghost
<Ghost R/G/B>
This function is used for the adjustment of Ghost.
The present PJ data are acquired and displayed on the screen.
The data acquired firstly (at the time of starting of the adjusting software) are stored as the initial value and
displayed on the left of the arrow mark. The present value is displayed on the right of the arrow.
When writing of the ADJ data is conducted with [Data], however, the written data are regarded as the initial
value.
The data come in 4 types for each color. During the adjustment, the increment and decrement actions are
carried out simultaneously for these 4 types.
Display the Test Pattern, and make adjustments with the use of the scroll bar so that Ghost becomes mini-
mum in the half-tone area on the right of the pattern, for R/G/B, respectively.
Adjusting range: “VT540” 00H - 2FH
“VT440” 00H - 17H
<Test Pattern>
This function is used when an internal Test Pattern is displayed for ghost adjustment.
When the [ON] button is clicked, an adjusting signal of Ghost is displayed on the projected screen.
When the [CLS] button is clicked, the Test Pattern is cleared (input changeover to RGB1).
<Data>
When the [Set] button is clicked, the adjusting signal of Ghost adjusted with the scroll bar is written in the
Flash ROM.
When the [Reset] button is clicked, the adjusted ghost value is restored to the initial value (at the time of
starting of the adjusting software) and written in the Flash ROM.
Note 1: The data adjusted with the scroll bar are the temporary ones. They are not sustained in the PJ without
taking any measures. Execute [Set] and write the data in the Flash ROM.
5-12
METHOD OF ADJUSTMENTS
4-5. Lamp
<Change time (Lamp Usage Time)>
This function is used when changing the lamp usage time.
The action for the modification of the lamp usage time should be carried out while the PJ power supply is
made to stay in the Standby mode.
At the beginning (at the time of adjusting software start), the projector data are acquired and stored as the
initial values.
However, if ADJ Data Write is performed with [Data], the written data are stored as the initial values.
If it is necessary to change the Lamp Usage Time, check the Change Time. Then the usage time is displayed
as “0 Hours” and the percentage indication as “100%.” When the display is like that, operation becomes
possible with the scroll bar, the [Set] button, and the [Reset] button.
Set up the proper time and percentage with the scroll bar.
When the [Set] button is clicked, the lamp usage time and percentage preset with the scroll bar are written in
the Flash ROM and displayed on the [Set] button.
When the [Reset] button is clicked, the lamp usage time and percentage are restored to the initial values (the
values at the time of adjusting software start) and written in the Flash ROM. Since then, the display on the
[Set] button is cleared.
After the Lamp Usage Time has been changed ([Set] and [Reset]), pull out the AC cord of the PJ without fail
and confirm that the Power LED is unlit.
When changing the Lamp Usage Time to “0 Hours” and “100%,” use the ON-screen menu. Then, clearing
becomes possible.
Setting range: 0 Hours - 3000 Hours
0% - 100%
5-13
METHOD OF ADJUSTMENTS
<Change time (Filter Usage Time)>
This function is used when changing the filter usage time.
The action for the modification of the filter usage time should be carried out while the PJ power supply is
made to stay in the Standby mode.
At the beginning (at the time of adjusting software start), the projector data are acquired and stored as the
initial values.
However, if ADJ Data Write is performed with [Data], the written data are stored as the initial values.
If it is necessary to change the Filter Usage Time, check the Change Time. Then the usage time is displayed
as “0 Hours.” At that time, operation becomes possible with the scroll bar, the [Set] button, and the [Reset]
button.
Set up the proper time with the use of the scroll bar or by directly entering the time data into the time display
editor.
When the [Set] button is clicked, the filter usage time preset with the scroll bar/editor input is written in the
Flash ROM and displayed on the [Set] button.
When the [Reset] button is clicked, the filter usage time is restored to the initial values (those at the time of
adjusting software start) and written in the Flash ROM. Since then, the display on the [Set] button is cleared.
Upon the completion of changing the filter usage time ([Set] and [Reset]), pull out the AC cord of the PJ
without fail and confirm that the Power LED is unlit.
When changing the Filter Usage Time to “0 Hours,” use the ON-screen menu in the serviceman mode. Then,
clearing becomes possible.
Setting range: Scroll bar 0 Hours - 32000 Hours
Editor input 0 Hours - 596523 Hours
<Change time (Panel Usage Time)>
This function is used when changing the panel usage time.
The action for the modification of the panel usage time should be carried out in the Standby mode at all times.
At the beginning (at the time of adjusting software start), the projector data are acquired and stored as the
initial values.
However, if ADJ Data Write is performed with [Data], the written data are stored as the initial values.
If it is necessary to change the Panel Usage Time, check the Change Time. Then the usage time is displayed
as “0 Hours.” At that time, operation becomes possible with the scroll bar, the [Set] button, and the [Reset]
button.
Set up the proper time with the use of the scroll bar or by directly entering the time data into the time display
editor.
When the [Set] button is clicked, the panel usage time preset with the scroll bar/editor input is written in the
Flash ROM and displayed on the [Set] button.
When the [Reset] button is clicked, the panel usage time is restored to the initial values (those at the time of
adjusting software start) and written in the Flash ROM. Since then, the display on the [Set] button is cleared.
After the Panel Usage Time has been changed ([Set] and [Reset]), pull out the AC cord of the PJ without fail
and confirm that the Power LED is unlit.
Upon the completion of changing the panel usage time ([Set] and [Reset]), pull out the AC cord without fail,
and confirm that the Power LED is unlit.
When changing the panel usage time to “0 Hours,” use the ON-screen menu to enable the clearing action in
the serviceman mode.
Setting range: Scroll bar 0 Hours - 32000 Hours
Editor input 0 Hours - 596523 Hours
5-14
METHOD OF ADJUSTMENTS
<Change time (Projector Usage Time)>
This function is used when changing the Projector Usage Time.
The action for the modification of the projector usage time should be carried out in the standby mode at all
times.
The present projector data are acquired and displayed on the screen.
The data acquired at the beginning (at the time of adjusting software start) are stored as the initial values and
displayed on the left of the arrow mark. The present values are displayed on the right of the arrow mark.
However, if ADJ Data Write is performed with [Data], the written data are stored as the initial values.
If it is necessary to change the Projector Usage Time, check the Change Time. Then, operation becomes
possible with the scroll bar, the [Set] button, and the [Reset] button.
Set up the proper time with the use of the scroll bar or by directly entering the time data into the time display
editor.
When the [Set] button is clicked, the projector usage time preset with the scroll bar/editor input is written in the
Flash ROM and displayed on the [Set] button.
When the [Reset] button is clicked, the projector usage time is restored to the initial values (those at the time
of adjusting software start) and written in the Flash ROM. Since then, the display on the [Set] button is
cleared.
After the Projector Usage Time has been changed ([Set] and [Reset]), pull out the AC cord of the PJ, without
fail, and confirm that the Power LED is unlit.
Setting range: Scroll bar 0 Hours - 32000 Hours
Editor input 0 Hours - 596523 Hours
<Language>
The default data setting of OSD display is carried out for the domestic (Japan) models (in Japanese) and the
overseas models (in English).
For the domestic (Japan) models, select [VTxxxJ Model].
For the overseas models, select [VTxxx, G, GS Model].
This setting is intended for the factory data only. Modification of user setting is not performed. (This is be-
cause of holding the user setting when ADJ data writing is effected with [Data].)
Note 1: In case of ADJ data Read/Write with [Data] during the replacement of the MAIN PWB, it is unneces-
sary to change the lamp, filter, panel,and projector usage time as well as the language since these
data have already been changed to the previous usage time.
Note 2: For the [Set]/[Reset] action of the lamp, filter, panel, and projector usage time, such operation should
be carried out in the standby state. In addition, these writing data cannot be written in the Flash ROM
unless the AC cord of the PJ is pulled out after the completion of [Set]/[Reset].
5-15
METHOD OF ADJUSTMENTS
4-6. Option
<Power>
Used for Power ON/OFF.
When ON/OFF is selected, the power supply is turned ON and OFF.
<Input Select>
Used for input changeover.
The input line is changed over to the selected input.
<Test Pattern>
Used to display the various internal test patterns.
[Flicker]: Horizontal line signal for flicker adjustment
[Ghost]: Signal for ghost adjustment
[Scale]: 16-gradation horizontal gray scale
[Cross]: Cross hatch
[100% Raster]: All-white raster
[50% Raster]: 50% brightness raster
[25% Raster]: 25% brightness raster
[0% Raster]: All-black raster
[CLS]: Test Pattern clear (Changed over to RGB1 input)
[R]/[G]/[B]: Test Patterns appearing in checked color except for [Ghost]
5-16
METHOD OF ADJUSTMENTS
<COM>
Used for the selection of PC Com Port and Baud Rate.
Communication cannot be maintained unless the Baud Rate does not coincide with the PJ setting.
The default setting for the PJ is 38400 bps.
<CRC>
The VT440/540 is provided with a protective function not to perform unwanted POWER ON when the internal
data (except for the adjusting data) have been changed. The CRC function is used in the case of failure in
POWER ON due to the modification of the internal data.
When this button is pressed, the data error detection table is updated so that it is available for the present
data.
5-17
METHOD OF ADJUSTMENTS
5. Error messages
“RS xxxxxx”
A communication error in conjunction with the PJ.
Examine the connections and confirm whether the main power supply of the PJ is turned ON or not.
“ACK Data length error,” “R-CheckSum error,” “Write error”
A communication error in conjunction with the PJ.
Confirm whether the PJ is really free from errors. Please repeat the action once more again.
“Can not open comport”
Failure in opening the serial port.
Confirm if there is any other application that uses the serial port.
“Do not open comport”
Communication is maintained under the condition that the opening of the above-mentioned serial port has
failed.
Confirm if there is any other application that uses the serial port.
“File format error,” “Address error”
During data writing from a file, the data format of the designated file is wrong.
Designate the correct file.
“Data write error!! Please retry.”
Data writing has failed. Please repeat the action once more again.
“Level error,” “Adjust error”
Failure in the automatic adjustment of Sub-Brightness/Sub-Contrast.
Please repeat the action once more again.
5-18
METHOD OF ADJUSTMENTS
1. Adjustment of the optical axis (Shadow adjustment)
1-1. Tools required
1-2. Preliminary arrangements before adjustments
1-3. Method of shadow adjustment in each color
Fig. 1 Flow Chart of Shadow Adjustment
Fig. 2 Objective Blocks to be Adjusted
2. Adjustment of the Polarizing Plate
2-1. Tools required
2-2. Preliminary arrangements before replacement
2-3. Replacement procedures
Fig. 3 Disassembly Diagram
5-19
METHOD OF ADJUSTMENTS
1. Adjustment of the optical axis (Shadow adjustment)
This adjustment is intended to remove color stain (defined as shadow hereafter) that may appear at the edge
part of the projected screen possibly caused by a problem around the optical engine block.
Adjustments can be carried out based on the flow chart in Fig. 1 and the objective blocks to be adjusted, shown
in Fig. 2.
1-1. Tools required
The following tools are required for adjustments:
<Tools to be used>
• Ball driver for FL adjustment and FL2 adjustment : Opposite side 2.0mm
(Ball driver DB-20 (2.0mm), Part No. : 92339583)
• Minus screwdriver for Mirror 1 adjustment: Blade width 5.0mm
<Jig for lamp lighting>
• Dummy load PWB (VT) (Part No.: 98999241)
1-2. Preliminary arrangements before adjustments
1) Remove the top cover Assy.
2) Remove the Main PWB Assy, the LCES or LCEX PWB Assy, and the Key PWB Assy.
3) Remove the Cover (suction air duct) Assy (Part No.: 24FT7461), the Suction air duct (SK) Assy (Part
No.: 24FT7451), and the Optical cover (SK) (Part No.: 24F32021).
Taking out the filter Assy B in advance facilitates the removal of the optical cover (SK).
4) Mount the dummy load and turn on the power source circuit.
5) Zoom the lens to maximum image size.
6) Adjust the focus of the screen overall by means of the lens focus adjuster. This adjustment should be
carried out in the all-white mode.
1-3. Method of shadow adjustment in each color
1-3-1. Vertical shadow adjustment for G and R (when the shadow color is magenta, cyan, or blue)
1
Replace the FL vertical adjusting screw. (Part name: Nylock screw (HLSS4*6), Part No.:
24N04751)
Then, follow the working procedures below by the use of a ball driver (opposite side 2.0mm).
Sufficiently loosen the FL vertical fixing screws (Part name: special screw (PL-HM2.5*6), Part
No.: 12851741) (in 2 positions).
Loosen the FL horizontal fixing screws by one turn (Part name: special screw (PL-HM2.5*6),
Part No.: 12851741) (in 2 positions).
Turn the FL vertical adjusting screw to eliminate the vertical shadow (magenta, cyan, and blue)
from the projected screen.
Fix the FL horizontal fixing screws (in 2 positions).
2
3
4
5
6
The fixing torque is 3.5 ± 0.5kgf·cm.
Fix the FL vertical fixing screws (in 2 positions).
The fixing torque is 3.5 ± 0.5kgf·cm.
5-20
METHOD OF ADJUSTMENTS
1-3-2. Vertical shadow adjustment for B (when the shadow color is yellow)
1
Replace the RL2 vertical adjusting screw. (Part name: Nylock screw (HLSS4*6), Part No.:
24N04751)
Then, follow the working procedures below by the use of a ball driver (opposite side 2.0mm).
Sufficiently loosen the RL2 vertical fixing screw (Part name: special screw (PL-HM2.5*6), Part
No.: 12851741) (in 1 position).
Loosen the RL2 horizontal fixing screw by one turn (Part name: special screw (PL-HM2.5*6),
Part No.: 12851741) (in 1 position).
Turn the RL2 vertical adjusting screw to eliminate the vertical shadow (yellow) from the pro-
jected screen.
Fix the RL2 horizontal fixing screw (in 1 position).
2
3
4
5
6
The fixing torque is 3.5 ± 0.5kgf·cm.
Fix the RL2 vertical fixing screw (in 1 position).
The fixing torque is 3.5 ± 0.5kgf·cm.
1-3-3. Horizontal shadow adjustment for G (when the shadow color is magenta or blue)
1
Loosen the FL horizontal fixing screws by one turn (in 1 position).
Move the FL to the right and left by hand, in order to eliminate the horizontal shadow (magenta
and blue) from the projected screen.
2
3
Fix the FL horizontal fixing screws (in 2 positions).
The fixing torque is 3.5 ± 0.5kgf·cm.
1-3-4. Horizontal shadow adjustment for R (when the shadow color is cyan)
1
2
3
Loosen the Mirror 1 fixing screw (Part name: PL-CPIMS2.5*6*15BF, Part No.: 910E2511) by 0.5
turns (in 1 position).
Using a minus screwdriver, turn and move the Mirror 1 to eliminate the horizontal shadow (cyan)
from the projected screen.
Fix the Mirror 1 fixing screw (in 1 position).
The fixing torque is 3.5 ± 0.5kgf·cm.
1-3-5. Horizontal shadow adjustment for B (when the shadow color is yellow)
1
Loosen the RL2 horizontal fixing screw by one turn (in 1 position).
Move the RL2 to the right and left by hand, in order to eliminate the horizontal shadow (yellow)
from the projected screen.
2
3
Fix the RL2 horizontal fixing screw (in 1 position).
The fixing torque is 3.5 ± 0.5kgf·cm.
5-21
METHOD OF ADJUSTMENTS
Start of adjustment
Check the vertical shadows of R, G, B.
Vertical shadows
present
No shadows
Shadows present
Shadows of G and
R present
Adjust the vertical shadows of G and R. (1-3-1)
No shadows
Check the vertical shadows of B.
Shadows present
Shadows of only B
present
Adjust the vertical shadows of B. (1-3-2)
Check the horizontal shadows of R, G, B.
Horizontal shadows
present
No shadows
Shadows present
Shadows of G
present
Adjust the horizontal shadows of G. (1-3-3)
No shadows
Check the horizontal shadows of R.
Shadows present
Shadows of R
present;
no shadows of G
Adjust the horizontal shadows of R. (1-3-4)
Check the horizontal shadows of B.
Shadows present
No shadows
Shadows of only
B present
Adjust the horizontal shadows of B. (1-3-5)
Check the vertical and horizontal shadows of R, G, B.
No shadows
Shadows present
End of adjustment
Fig. 1
5-22
Fig. 2
METHOD OF ADJUSTMENTS
2. Adjustment of the Polarizing Plate
It is unnecessary to adjust the polarizing plate.
If the polarizing plate is damaged, however, it is necessary to replace the polarizer and the mounting metal fitting
(POL).
<Replacement procedures>
2-1. Tools required
The following tools are required for this replacement:
<Tools to be used>
• Ball driver for polarizing plate fixing screw mounting and dislodgment : Opposite side 1.5mm
(Ball driver DB-15 (1.5mm) Part No. : 9N000001).
2-2. Preliminary arrangements before replacement
1) Remove the top cover Assy.
2) Remove the Main PWB Assy, the LCES or LCEX PWB Assy, and the Key PWB Assy.
3) Remove the Cover (suction air duct) Assy (Part No.: 24FT7461), the Suction air duct (SK) Assy (Part
No.: 24FT7451), and the Optical cover (SK) (Part No.: 24F32021).
Taking out the filter Assy B in advance facilitates the removal of the optical cover (SK).
2-3. Replacement procedures
1) Remove the polarizing plate Sassy.
Then start the work below for the polarizing plate sassy.
2) Take out the mounting metal fitting (POL) from the condenser lens Assy.
3) Mount a new polarizer on the new mounting metal fitting (POL).
If the mounting metal fitting (POL) is attached with double coated adhesive tapes (in 2 positions), the
mounting of the polarizer should be done after the removal of the peel-off paper.
4) For the item assembled as per 3) above, mount this item on the condenser lens Assy.
In this case, the mounting metal fitting (POL) shall be fixed at the right angles with the condenser lens
Assy. The fixing torque for the polarizing plate fixing screw shall be 1.5 to 2.0kgf·cm.
Note) In regard to the polarizing plate R sassy, the polarizing plate G sassy, and the polarizing plate B
sassy, the mounting angles for the respective polarizing plate fixing screws differ from each
other. Make sure not to confuse these angles. (See Fig. 2.)
5) Mount the polarizing plate sassy, each assembled as per 4) above.
5-24
METHOD OF ADJUSTMENTS
Fig. 3
5-25
METHOD OF ADJUSTMENTS
Picture Quality Decision Criteria
Judge units that satisfy the following criteria as acceptable.
(1) Pixel Mis-Convergence
The pixel Mis-Convergence of the red and blue shall be as specified below in reference to the green.
• 1 pixel or less in the center area
• 1 pixel or less in the peripheral (Edge) areas
Mis-Convergence of one quarter (1/4) or more from the above specifications (1 1/4 pixels in the peripheral
area) may be acceptable, provided that the signal color of green registers with the pixels of the other colors and
does not appear seriously poor as viewed 2 meters away.
(2) A bright pixel defect is always visible on a totally black screen in units of pixels.
Up to 6 pixel defects are permissible for a single color, or up to 18 pixel defects for all the three colors combined.
Bright spots of less than 1 pixel are acceptable unless they are frequently visible 2 meters away.
(This does not apply to bright spots concentrated or markedly visible.)
(3) Dust, smear
Any dust or smear visible in excess of 2 pixels is not permissible at the best focus point.
(2) Replace the LCD panel if bright spot defects exceed the specified level.
(3) Remove dirt and smear in excess of the permissible level.
Lens and Mirror Cleaning
(1) Lens Cleaner
* Cleaning fluid
Use absolute alcohol.
If moisture remains on the surface without drying soon after it is cleaned, use
fresh absolute alcohol.
* Cleaning method
Soak a clean cotton cloth or a sheet of commercial cleaning paper with the
cleaning fluid. Hold it between your thumb and index finger, and start cleaning
the lens at the center and circle the cloth or paper toward the edge, wiping off
foreign matter out to the edge. Do not apply pressure on the lens surfaces
while cleaning.
(2) Mirror Cleaner
Never grip the mirror hard because it is vapor-deposited. Minor stains may be removed by dissolving them with
alcohol and wiping off dry.
(3) Point
Stains on both sides of the LCD unit and on the LCD side of the field lens degrade the picture. Keep them
clean.
5-26
CIRCUIT DESCRIPTION
LC driver block
1. Circuit configuration
1-1 PWB configuration
• MAIN PWB
Used for the phase decode processing of the RGB video signals, the level adjustment, and the genera-
tion of various timing signals.
• Used for the level shift processing of the panel drive timing signals for the LCES PWB (SVGA) and the
LCEX PWB (XGA), and also for the generation of panel auxiliary signals.
• The above-mentioned two types of PWBs are connected through the FFC (Flexible Flat Cable) cables
of 40 pins (POSV) and 30 pins (POST).
2. Output signal
2-1 Signal level
• RGB video signal
• Panel driving signal : 15.5Vp-p (0.0V/15.5V)
• Panel aux. signal : 5.0Vp-p (2.5V/7.5V)
: 10.0Vp-p (2.0V/12.0V)
2-2 Driver panel
• SVGA : Model 0.9 LC panel (P09SG210) by EPSON
• XGA : Model 0.9 LC panel (P09XG210) by EPSON
3. Outline hardware description
3-1 RGB video signal
This signal output is generated from the signal processing circuit G/A, UNI2 (IC3601), on the main board
(MAIN PWB). Each 10-bit R,G,B digital video signal (3.3Vp-p) is processed for 6/12 (SVGA/XGA) phase
decode processing by the phase decoding ICs (IC3701, 3702, 3703, 3704, 3705, 3706), and also for the
level adjustment (10.0Vp-p (2.0V/12.0V)) by the serial D/A (IC3711). Since then, each signal is fed to the
LC panel through the LC driver boards (LCES PWB/ LCEX PWB).
3-2 Panel driving signal
This signal output is generated from the signal processing circuit G/A, YAMAG (IC3701), on the same
main board (MAIN PWB). The panel drive timing signal (3.3Vp-p) is processed for level shifting to the level
(15.5Vp-p) required to drive the shift register in the LC panel by the aid of the level shift ICs (IC5201, 5202,
5203/ IC6201, 6202, 6203) located on the LC driver boards (LCES PWB/ LCEX PWB). Since then, the
processed signal is fed to the LC panel.
3-3 Panel auxiliary signal
This signal output is generated from the LC panel signal processing circuit G/A, YAMAG (IC3701), on the
same main board (MAIN PWB). The panel auxiliary signal (3.3Vp-p) is processed for level shifting to the
level (5.0Vp-p, (2.5V/7.5V)) required to pre-charge the video line in the LC panel by the aid of the level
shift ICs (IC5201, 5202, 5203/ IC6201, 6202, 6203) located on the LC driver boards (LCES PWB/ LCEX
PWB). Since then, the processed signal is fed to the LC panel via the diamond buffer of the complex
transistor group.
6-1
CIRCUIT DESCRIPTION
3-4 Interface between MAIN and LCES, LCEX
P0SV
P0ST
Signal name
Pin No.
Signal name
Pin No.
1
2
3
4
5
6
7
8
A+17.5V
A+17.5V
VIDR/2
VIDR/4
VIDR/6
VIDR/8
VIDR/10
VIDR/12
VIDR/1
VIDR/3
VIDR/5
VIDR/7
VIDR/9
VIDR/11
AGND
VIDG/2
VIDG/4
VIDG/6
VIDG/8
VIDG/10
VIDG/12
VIDG/1
VIDG/3
VIDG/5
VIDG/7
VIDG/9
VIDG/11
AGND
VIDB/2
VIDB/4
VIDB/6
VIDB/8
VIDB/10
VIDB/12
VIDB/1
VIDB/3
VIDB/5
VIDB/7
VIDB/9
VIDB/11
1
2
3
4
5
6
7
8
DGND
DY
CLY
NRG
NRC
D+5V
DGND
DX
9
9
CLX
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
ENB1R
ENB2R
DGND
ENB1G
ENB2G
ENB1B
ENB2B
D+5V
DGND
SHENB
SHCLP
ENBY1
ENBY2
DGND
(NC)
DIRY
DIRX
SCLK
D+5V
ADATA
DGND
6-2
CIRCUIT DESCRIPTION
3-5 List of I2C control ICs (Output block)
Item name
M62398FP
Circuit symbol
IC5103/IC6103
Function
Slave address
92H
Remarks
Serial D/A
Output video level adjustment,
flicker adjustment
3-6 Interface with the LC panel
SVGA panel
XGA panel
POREX/GEX/BEX
Pin No. Signal name
DY
PORES/GES/BES
Pin No.
Signal name
1
2
3
DY
CLY
CLY
1
2
CLY
CLY
3
4
5
6
7
8
9
VDDY
NRG
DIRY
LCCOM
ENB1
ENB2
DIRX
CLX
CLX
DX
VDDX
NC
NC
VSSX
VID1
VID2
VID3
VID4
VID5
VID6
VSSX
LCCOM
NRS1
NRS2
VSSY
VSSY
DY
4
5
6
7
8
9
NRG
VDDY
VDDX
CLX
CLX
DX
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
ENB2
ENB1
DIRX
VSSX
VID1
VID2
VID3
VID4
VID5
VID6
VID7
VID8
VID9
VID10
VID11
VID12
NRS
LCOOM
DY
DIRY
VSSY
6-3
CIRCUIT DESCRIPTION
I/O Block, VIDEO Processor Block, SYNC Block
1. I/O terminals
1-1 Video input
• RCA PHONO terminal for composite video signal input (1 system)
• S VIDEO input terminal (1 system)
1-2 RGB input (Application to the component input through the conversion cable)
• Mini D-SUB 15-pin (1 system) (plug & play applicable)
1-3 RGB output
• Mini D-SUB 15-pin (1 system)
1-4 Audio I/O
• Mini jack for audio I/O (For both input and output; used in common for respective video signals)
• RCA PHONO terminal for audio I/O (For both input and output; used in common for respective video
signals)
1-5 PC CONTROL terminal
• Mini DIN-8P (1 system)
• External control applicable
2. Input signals
2-1 Signal level
• Composite video : 1.0Vp-p/75Ω
• S VIDEO input
• RGB signal
• Sync signal
: 1.0Vp-p/75Ω (Signal Y), 0.28Vp-p/75Ω (Signal C burst level)
: 0.7Vp-p/75Ω
: TTL level (positive/negative)/ 1kΩ
• Component signal: 1.0Vp-p/75Ω (Signal Y), 0.7Vp-p/75Ω (Signal Cb/Cr, Pb/Pr)
• Audio signal
: 0.5Vrms/47kΩ
2-2 Color system applicable to video input
• NTSC3.58
• NTSC4.43
• PAL
• PAL-60
• SECAM
• B/W60, B/W50 (B/W: Black-and-white signal without burst)
2-3 Scanning frequency applicable to RGB signals
• Horizontal: 15 to 100kHz
• Vertical: 50 to 117 Hz
2-4 Component signals
• Component video Y/Cb/Cr (DVD output signal)
• HDTV 720p signal, 1080i signal, 480p signal
6-4
CIRCUIT DESCRIPTION
3. I/O PWB block
3-1 RGB OUT circuit
The RGB video signal input entered in Pin 15 of the Mini D-SUB is amplified at the 6dB amplifier (IC4000;
AD8013AR) so that it attains 1Vp-p at the time of 75Ω termination.
The H Sync output is generated through the buffer circuit (Q4000 to Q4002).
The V Sync output is in the THROUGH OUT.
3-2 Plug & Play
The V Sync terminal of Pin 15 of the Mini D-SUB and the serial terminal of Pins 12 and 15 are connected
to the Plug & Play IC (IC4001: 12LC21T) so that the projector can be detected at the PC.
4. MAIN PWB block
4-1 Video signal processor block
The composite video signal passes through the 6dB amplifier (IC1100; MM1031XM) and the low-pass
filter (FL1113), and enters Pin 41 of the video decode IC (IC1104: CXA2139S) at 1Vp-p. The NTSC and
PAL signals are led to the IC’s internal SW and 6dB amplifier, and the resultant output is fed to Pin 6. The
signals are further sent to the 3-line Y/C separator circuit (IC1101: TC9090AF). The signals from Y/C
separation are returned again to the video decode IC.
The composite SECAM signal and the B/W signal do not pass through the 3-line Y/C separator circuit. The
composite SECAM signal is processed for Y/C separation by the BPF & TRAP that is incorporated in the
video decode IC.
The SF video input signal is directly entered in the video decode IC.
The result of discrimination for the color system, vertical frequency, etc., to be conducted at the video
decode IC is supervised by the CPU through the I2C bus. According to this result, the CPU controls the 3-
line Y/C separator IC and the video decoder at the appropriate setting values through the I2C bus.
In the video decode IC, the sharpness control and the compensation for the phase in conjunction with the
chroma output signal are carried out for Signal Y. The signal decoded (decoding angle = 90ÅB) to the Y/
chroma in the video decode IC is entered in the A/D converter IC (IC3401: CXA3506R).
The sync signal contained in the Y signal selected by the switch of the video decode IC is sent as the H·V
timing pulses to the sync signal changeover block (IC3301: YAMAG) at the next stage, through the hori-
zontal and vertical sync separator circuit in the IC, the copy guard signal mask circuit, the AFC circuit, IC’s
external mono-multi circuit, etc.
4-2 Sync signal processor block (Mini D-SUB 15-pin input)
The sync signal input entered in Pin 15 of the Mini D-SUB is sent to the amplitude limiter circuit. In this
amplitude limiter circuit, the H/V sync signal limited to 0.6Vp-p is applied to the sync signal processor IC
(IC1006: M52347FP).
In order to cope with the sync attenuation signals, the Sync on Green signal input is entered in the sync
signal processor IC via the Sync chip clamp circuit and the AMP circuit. The DVD signal only is entered in
Pin 43 of the video decode IC via IC1001, so that sync processing is conducted in the same manner as for
the video signals.
In the sync signal processor IC, the following processing is carried out:
• Discrimination of the presence of H/V Sync
• Discrimination of the polarity of H/V Sync
• Sync separation for the composite Sync
• Sync separation for the G-Sync
• Generation of clamp pulses
• H/V Sync output
The result of discrimination is read out at the serial D/A (IC1003: CXA1315) and sent to the CPU. The H/
V Sync output is sent to the Sync signal changeover block (IC3301: YAMAG). After the completion of
output synchronization and selection for the video decode IC, the H sync signal is sent to the A/D con-
verter IC (IC3401: CXA3506R) and the V sync signal is sent to the signal processor IC (IC3502: En-
deavor).
6-5
CIRCUIT DESCRIPTION
4-3 RGB/Component signal processor and A/D converter block
The video signal input entered in Pin 15 of the Mini D-SUB is fed to theA/D converter IC (IC3401: CXA3506R)
through the buffer circuit. In the case of a component signal, only the chroma signals (Pb, Pr, Cb, Cr) are
entered after their levels have been lowered at the attenuator of -6B.
In the A/D converter IC, the video signal from the video decode IC or the video signal at Pin 15 of the Mini
D-SUB is selected. After the contrast has been adjusted at the built-in analog amplifier, this signal is
processed for A/D conversion into the 8-bit digital signal.
The 8-bit digital signal is entered in the signal processor IC (IC3502: Endeavor) for signal processing.
The signal to be used to clamp the video signal (clamp pulses) is the clamp pulse signal from the sync
signal processor IC (IC1006: M5234FP) or the one from the signal processor IC (IC3502: Endeavor)
chosen by the changeover action at the signal changeover block (IC3301: YAMAG). This signal is then
entered in the A/D converter IC (IC3401: CXA3506R) for signal clamping. Generally for the VIDEO and
HD signals, the clamp pulses of the signal processor IC are used. For the RGB signals, the clamp pulses
of the sync signal processor IC are generally used.
4-4 Audio signal processing
The audio signal passes through the buffer circuit of the MAIN PWB, and is then fed to the output AMP IC
(IC4100: AN7512SH) that is incorporated in the VOLUME control of the KEY PWB.
The VOLUME control is effected at the serial D/A (IC1003: CXA1315). The amplified audio signal is output
(MAX: 1W) to the speaker system (8W x 1).
4-5 Interface with I/O PWB and MAIN PWB
Pin No.
Signal name
Pin No.
Signal name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DGND
EXT3
EXT2
EXT1
DGND
RXD
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
S-C
AGND
S-Y
AGND
CV
AGND
V
AGND
H
AGND
B
AGND
G
AGND
R
DGND
TXD
DGND
VCCS+5V
VCCA+9R1
VCCA+9R1
AGND
AUDIO
AGND
4-6 List of I2C control ICs
Item name
Circuit symbol
Function
Slave address
Remarks
CXA2139S
TC9090AF
CXA1315M
CXA3506R
IC1104
IC1101
IC1003
IC3401
Video decode
Y/C separation
Serial D/A
8AH/8BH
B2H
40H/41H
9AH
A/D converter
6-6
CIRCUIT DESCRIPTION
Signal Processor Block
1. PLL block
The PLL block is incorporated in the A/D converter (IC3401). In the PLL block, the dot clock signal is generated
in synchronization with the horizontal sync signal input. This clock signal is fed to the ENDEAVOR (IC3502).
2. ENDEAVOR (IC3502)
The ENDEAVOR (IC3502) is an LSI used as the center of video signal processing. The video signal (8 bits x 3)
digitized at the A/D converter is entered in the ENDEAVOR, where frequency conversion, definition conversion,
ON-screen signal mixing, V-T compensation, etc., are carried out. The resultant signal is output to the G/A, UNI2
(IC3601), for the color irregularity compensation.
These ENDEAVOR functions are used with the aid of the frame memory composed of the built-in SDRAM.
3. CPU block
The CPU block is composed of the CPU (IC3205), SRAM x 4 (IC3201-3204), 4M FLASH ROM (IC3207), 8M
FLASH ROM x 2 (IC3208-3209), and the YAMAG (IC3301). This block is used for various projector controls.
The booting programs and various data are accommodated in the 4M FLASH ROM, while the main programs
are accommodated in the 8M FLASH ROM.
4. YAMAG (IC3301)
The YAMAG (IC3301) incorporates the various functions as specified below.
Generation of the address decode and chip select signals
Frequency measurement and interlace discrimination circuit
I/O port (3 x 8 bits)
Beat cancel circuit (Frequency divider circuit, phase comparison, random generation)
2 → 1 sync signal and clamp pulse changeover and sync width variable circuit
Fan rpm control circuit (2 systems of PWM)
Remote control decode, key, external control mixing, and interrupt generator circuit
Timing signal generator circuit for the LC panel
5. UNI2 (IC3601)
The UNI2 is the color irregularity compensation IC for the 10-bit input - 10-bit output. The color irregularity
compensation data of 25 x 20 = 500 points are accommodated in the screen. By these compensation data and
linear interpolation, compensation for the color irregularity is carried out in the screen.
6-7
METHOD OF DISASSEMBLY
1. Main unit diagonal view
7-1
METHOD OF DISASSEMBLY
2. FILTER ASSY A/FILTER ASSY B/LAMP COVER ASSY/CAP
1
(1) Loosen the one screw , and take out the LAMP
COVER ASSY.
(2) Take out the FILTER ASSY A/FILTER ASSY B/
and the CAP.
FILTER ASSY B
LAMP COVER ASSY
1
Screw
CAP
FILTER ASSY A
7-2
METHOD OF DISASSEMBLY
3. TOP COVER ASSY/STAY R/FILTER F
(3) Remove the FILTER F.
1
(1) Remove the five screws , and take out the TOP
COVER ASSY.
(2) Remove the two screws , and take out the STAY
Note) Refer to P7-4 and P7-5.
2
R.
1
Screw
STAY R
TOP COVER ASSY
1
2
Screw
1
FILTER F
1
1
7-3
METHOD OF DISASSEMBLY
B
A
C
A
B
C
1: Hold both sides of the set with both hands at Part A. Apply a force to Part B in the direction of the
arrow (diagonally toward the top of the set). In this case, the force being applied should be as low
as possible in order not to damage the switch.
2: Confirm that the claw of C (each side surface) has been disengaged.
7-4
METHOD OF DISASSEMBLY
3: Remove the top cover in the direction of the arrow. At that time, this action should be done in the
direction of rotation, with the front side of the cabinet regarded as a fulcrum.
When mounting the top cover, the procedures should be reverse as those for the removal.
7-5
METHOD OF DISASSEMBLY
4. LAMP BOX SASSY
1
(1) Loosen the two screws , and take out the LAMP
BOX SASSY.
LAMP BOX SASSY
1
Screw
7-6
METHOD OF DISASSEMBLY
5. MAIN PWB ASSY
1
(1) Remove the four screws , and take out the MAIN
PWB ASSY.
1
Screw
MAIN PWB ASSY
7-7
METHOD OF DISASSEMBLY
6. LCEX PWB ASSY (VT540 System)/LCES PWB ASSY (VT440 System)/KEY PWB ASSY/
BARRIER (B/M)
1
2
(1) Remove the two screws
and two studs, and
(2) Remove the three screws , and take out the
take out the LCEX PWB ASSY (VT540 System)
and the LCES PWB ASSY (VT440 System).
KEY PWB ASSY and the BARRIER (B/M).
2
Screw
STAD
1
Screw
KEY PWB ASSY
BARRIER (B/M)
• LCEX PWB ASSY
(VT540)
• LCES PWB ASSY
(VT440)
7-8
METHOD OF DISASSEMBLY
7. POWER UNIT
1
(1) Remove the three screws
and the two screws
2
, and take out the POWER UNIT.
1
Screw
POWER UNIT
2
Screw
7-9
METHOD OF DISASSEMBLY
8. OPTICAL ENGINE ASSY
1
(1) Remove the five screws , and take out the OP-
TICAL ENGINE ASSY.
1
Screw
OPTICAL ENGINE ASSY
7-10
METHOD OF DISASSEMBLY
9. OPTICAL ENGINE ASSY
7-11
METHOD OF DISASSEMBLY
10. ZOOM LENS (SK)
(1) Remove the four screws
ZOOM LENS (SK).
1
, and take out the
1
Screw
ZOOM LENS (SK)
1
Screw
7-12
METHOD OF DISASSEMBLY
11. COVER (INHAIL DUCT) ASSY/INHAIL DUCT (SK) ASSY/STOPPER (XDP) ASSY
1
(1) Remove the COVER (INHAIL DUCT) ASSY.
(3) Remove the three screws
and the stud, and
2
(2) Remove the two screws
STOPPER (XDP) ASSY.
, and take out the
take out the INHAIL DUCT (SK) ASSY.
COVER (INHAIL DUCT) ASSY
STAD
1
Screw
INHAIL DUCT (SK) ASSY
1
Screw
2
Screw
STOPPER (XDP) ASSY
7-13
METHOD OF DISASSEMBLY
12. COVER OPT (SK)
(1) Remove the eight screws , and take out the
COVER OPT (SK).
1
1
Screw
1
Screw
COVER OPT (SK)
7-14
METHOD OF DISASSEMBLY
13. OPT BASE SASSY/BARRIER (XDP)
1
(1) Remove the two screws , and take out the OPT
BASE SASSY.
(2) Remove the BARRIER (XDP).
1
Screw
BARRIER (XDP)
OPT BASE SASSY
7-15
METHOD OF DISASSEMBLY
14. R POL SASSY/G POL SASSY/B POL SASSY
(1) Remove the R,G,B POL SASSY.
B POL SASSY
R POL SASSY
G POL SASSY
7-16
METHOD OF DISASSEMBLY
15. MIRROR ASSY1 (SKT)/DICHROIC MIRROR 1 (SK)/DICHROIC MIRROR 2 (SK)/
MIRROR 0 (SK)/MIRROR 2 (SK)/RELAY LENS ASSY 1 (SK)/RL2 SASSY/SPRING S
1
(1) Remove the one screw , and take out the MIR-
(4) Remove ten pieces of SPRING S, and take out
one each of the DICHROIC MIRROR 1 (SK),
DICHROIC MIRROR 2 (SK), MIRROR 0 (SK), and
also the two pieces of MIRROR 2 (SK).
ROR ASSY1 (SKT).
2
(2) Remove the one screw , and take out the RE-
LAY LENS ASSY 1 (SK).
3
(3) Remove the one screw , and take out the RL2
SASSY.
SPRING S
MIRROR 0 (SK)
DICHROIC MIRROR 2 (SK)
DICHROIC MIRROR 1 (SK)
RELAY LENS ASSY (SK)
2
Screw
MIRROR 2 (SK)
RL2 SASSY
1
Screw
3
Screw
MIRROR ASSY 1 (SKT)
7-17
METHOD OF DISASSEMBLY
16. FL SASSY/IT1 SASSY/IT2 SASSY/BARRIER 2 (SEPARATE BASE)/
BARRIER 1 (SEPARATE BASE)/THERMOSTAT
1
4
(1) Remove the two screws
THERMOSTAT.
, and take out the
(4) Remove the two screws , and take out the BAR-
RIER 1 (SEPARATE BASE).
(5) Remove the two screws 5 , and take out the FL
SASSY.
2
(2) Remove the two screws , and take out the IT1
SASSY.
3
6
(3) Remove the two screws , and take out the BAR-
(6) Remove the two screws , and take out the IT2
RIER 2 (SEPARATE BASE).
SASSY.
Screw 5
1
Screw
IT2 SASSY
Screw
THERMOSTAT
6
2
Screw
IT1 SASSY
3
Screw
FL SASSY
BARRIER 2
(SEPARATE BASE)
BARRIER 1(SEPARATE BASE)
4
Screw
7-18
METHOD OF DISASSEMBLY
17. DUCT CASE (SK) ASSY
1
(1) Remove the three screws , and take out the
DUCT CASE (SK) ASSY.
DUCT CASE (SK) ASSY
1
Screw
7-19
METHOD OF DISASSEMBLY
18. BRACKET (I/O) ASSY/I/O PWB ASSY/REMOCON CASE UNIT
1
3
(1) Remove the one screw
BRACKET (I/O) ASSY.
, and take out the
(3) Remove the one screw
REMOCON CASE UNIT.
, and take out the
2
(2) Remove the three screws , and take out the I/O
PWB ASSY.
BRACKET (I/O) ASSY
1
Screw
I/O PWB ASSY
REMOCON RD-366E
2
Screw
REMOCON CASE UNIT
3
Screw
7-20
METHOD OF DISASSEMBLY
19. SCIROCCO FAN
1
(1) Remove the five screws
SCIROCCO FAN.
, and take out the
1
Screw
SCIROCCO FAN
7-21
METHOD OF DISASSEMBLY
20. HANDLE/BRACKET (HANDLE)/SHAFT (HANDLE)/SPEAKER/SPEAKER HOLDER/
FILTER S/FILTER R
1
2
(1) Remove the two screws , and take out the two
(3) Remove the one screw
, and take out the
BRACKET (HANDLE).
SPEAKER HOLDER and the SPEAKER.
(2) Remove the two SHAFT (HANDLE), and then take
out the HANDLE.
2
Screw
BRACKET
(HANDLE)
1
Screw
FILTER S
FILTER R
1
Screw
SPEAKER HOLDER
SHAFT
(HANDLE)
HANDLE
SPEAKER
FILTER S
7-22
MEMO
DISASSEMBLY
• MAIN BODY
S01
S03
M02
E02
E06
S12
E09
M03
S01
S12
S03
S04
S13
S13
S12
M27
S03
M21
M26
S12
S12
S12
M29
M04
M22
M23
S12
M20
E07
M30
E10
S01
M25
M24
E03
M19
S06
S12
E05
M28
S03
M22
S03
S03
M45
S03
8-1
DISASSEMBLY
• OPTICAL ENGINE
S05
S06
S01
E04
E08
S06
M40
S02
S06
S01
M41
E01
M01
S07
M42
S06
M43
S06
M13
M11
M43
M06
M08
S10
M17
S06
M07
M10
S06
M36
S06
M09
M37
S05
M05
M38
S06
M43
M43
S09
M35
M12
S11
M39
M08
M14
S05
M15
M18
S08
M16
S06
M44
S08
8-2
DISASSEMBLY
• RL2 SASSY
S05
M46
M47
S14
8-3
DISASSEMBLY
• POL SASSY
CONDENSER LENS ASSY
PLATE (POL)
POLARIZER
POL and POLARIZER ASSY
R POL ASSY
G POL ASSY
B POL ASSY
SCREW
POL SASSY PART LIST
R POL SASSY
G POL SASSY
PART NO
B POL SASSY
PART NO
COMPONENTS
PART NO
24H36661
12JS1551
PLATE(POL)
24H36661
12JS1561
12JS1361
24N04761
24H36661
POLARIZER 1(SK)
POLARIZER 2(SK)
POLARIZER 3(SK)
CONDENSER LENS ASSY 1(SK)
CONDENSER LENS ASSY 2(SK)
SCREW
12JS1571
12JS1361
24N04761
12JS1371
24N04761
8-4
DISASSEMBLY
• FL SASSY
S05
M48
M49
S14
8-5
PACKAGING
Packing Procedures
1. VT440
9-1
PACKAGING
2. VT440G
9-2
PACKAGING
3. VT540
9-3
PACKAGING
4. VT540G
9-4
REPLACEMENT PART LIST
Notes:
1. Parts orders must contain model name, parts number and
description.
2. When you place an order for spare parts, please refer to
the respective service manual and mention the right parts
number on your P.O. Sheets.
3. The components identitied by a mark or with the symbol
Nos. shaded are critical for safety. Replace only with parts
number specified.
The letters NSP in the table indicate non-service parts.
1. VT440
SYMBOL
PART NO
DESCRIPTION
*** PWB ASSYS ***
E01
E02
E03
E04
935Y1D01
935Y1F01
935X7NA1
935X7NB1
LCES PWB ASSY
MAIN PWB ASSY
I/O PWB ASSY
KEY PWB ASSY
*** ELECTRICAL PARTS & MISCELLANEOUS PARTS ***
E05
79646932
73895159
73895160
70ED2315
70ED2315
70ED2315
70ED2165
70ED2404
70ED2038
70ED2166
31700104
38102078
63099063
73W20077
73WLW001
64003036
64003037
64KA1118
64KA1122
64KA1140
65904524
65904524
65AB1116
65CF1506
65FK2102
66500003
66KA2008
POWER UNIT
CABLE,FFC 30P*38 P0.5 SO
CABLE,FFC 40P*38 P0.5 SO
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
FPC CONNE FH12-30S-0.5SH
CONNECTOR,FFC 40P
CONNECTOR,FPC 40P
SCIROCCO FAN
THERMISTOR104JT-075-90271
SPEAKER 40*28MM 8H 1W
CN2P(SP)220S,1685-26
CN22P(MK)60W,1685-26
CRYSTAL RESONATOR
CRYSTAL RESONATOR
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
CRYSTALOSCILLATOR33.33333
DETECTOR SWITCH
DETECTOR SWITCH
SW,SLIDE
POBES
POGES
PORES
POST
POST
POSV
POSV
E06
E07
X1101
X1100
X3501
X3502
X3503
SW3313
SW4100
SW3301
SWITCH,TACT
RELAY
THERMOSTAT
DETECTOR SWITCH
RL3100
E08
SW3312
10-1
VT440
*** APPEARANCE PARTS ***
S05
S06
S11
S09
S07
S01
S08
S03
S12
S13
12851741
910E2511
24N04721
910E2521
910E2531
910E306L
24N04781
910D3066
91613061
91614031
24N03651
24N04352
24N04691
24N04701
24N04731
24N04741
24N04751
24N04761
24N04771
91052031
91283076
91613076
12J00291
12J00301
12J00351
12J00361
12J00371
12J00381
12J00391
12J00401
12J00411
12J00421
12JS1351
12JS1361
12JS1371
12JS1381
12JS1391
12JS1431
12JS1441
12JS1451
OR 12JS1471
12JS1481
OR 12JS1491
12JS1501
12JS1511
12JS1521
SPECIAL SCREW(PL-HM2.5*6)
PL-CPIMS*2.5*6*15BF
SCREW(WASCHER 2.5*10)
PL-CPIMS*2.5*8*15BF
PL-CPIMS*2.5*10*15BF
PL-CPIMS*3*10*3GF
SPECIAL SCREW(PL-HM3*16)
PL-CPIMS*3*10*3KF
SCREW,#2CBTS*3*10*15BF
SCREW,#2CBITS*4*12*15BF
STUD(D-SUB,M2.6*3GF)
SPECIAL SCREW(M4)
STAD(M3*14,M/FM)
S02
S10
STAD(M3*17.5,M/FM)
SCREW(CBIPS2*6,PRECOAT)
SCREW(CFIPS3*6*15BF)
SPECIAL SCREW(HLSS4*6)
SCREW(PL-HHIMS2*5)
SCREW(CBIPS 3*10*15BF)
CFIMS2*6*15BF
SCREW,#2CPTS*3*12*3KF
SCREW,#2CBTS*3*12*3KF
CROSS PRISM(SKN)
S14
S04
CROSS PRISM(SKF)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
FIELD LENS(SK)
CONDENSER LENS 1(SK)
CONDENSER LENS 2(SK)
RELAY LENS 1(SK)
RELAY LENS 2(SK)
MIRROR 1(SK)
M48
FIELD LENS ASSY(SK)
CONDENSER LENS ASSY1(SK)
CONDENSER LENS ASSY2(SK)
RELAY LENS ASSY1(SK)
RELAY LENS ASSY2(SK)
ZOOM LENS(SK)
INTEGRATOR1(SKA)
INTEGRATOR2(SKA)
INTEGRATOR2(SKA)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
MIRROR 0(SK)
MIRROR ASSY1(SK)
MIRROR 2(SK)
M05
M46
M44
M06
M07
M08
10-2
VT440
*** APPEARANCE PARTS ***
M09
M10
12JS1531
12JS1541
12JS1551
12JS1561
12JS1571
12JS1581
12JS1601
12JS1711
12JS1721
18775141
25765841
25781322
24BS6621
24C02681
24C05911
24D11271
24D11421
24DT7492
24DT7665
24F29461
24F30581
24F31771
24F31781
24F31791
24F31801
24F31811
24F31821
24F31861
24F31871
24F31881
24F31901
24F31921
24F31931
24F31941
24F31951
24F31971
24F31981
24F31991
24F32011
24F32021
24F32031
24F32041
24F32051
24F32061
24F32071
24F32081
DICHROIC MIRROR 1(SK)
DICHROIC MIRROR 2(SK)
POLARIZER 1(SK)
POLARIZER 2(SK)
POLARIZER 3(SK)
REFLCTER LAMP(SK)
COVER GLASS(SK)
POLARIZER 3(SKK)
MIRROR ASSY1(SKT)
LABEL,SERIAL MANUFACTURE
LABEL(1*10)
LABEL,BARCODE
REMOCON CASE UNIT
CLIP(DS-9UL)
M19
TILT RIVET
BOTTOM COVER
TOP COVER(VT440)
BOTTOM COVER ASSY
TOP COVER ASSY
TILT FOOT(R)
CUSHION FOOT(R)
HOLDER(CL1)
HOLDER(CL2)
HOLDER(FL)
HOLDER(RL1)
HOLDER(RL2)
HOLDER(M1)
INDICATOR
FILTER F
TILT FOOT F
HANDLE
CUSHION (FRONTFOOT)
LAMP COVER
FILTER CASE A
FILTER CASE B
SPEAKER HOLDER
FILTER S
M45
M03
M20
M28
M22
M23
FILTER R
SEPARATE BASE(SK)
COVER OPT(SK)
DUCT CASE(SK)
INHAIL DUCT(SK)
COVER(INHAIL DUCT)
STOPPER(XDP)
LAMP BOX(F)
M13
LAMP BOX(T)
10-3
VT440
*** APPEARANCE PARTS ***
24F32091
24F32561
LAMP BOX(B)
TILTINSERT
M24
M04
M21
M27
24FT6951
24FT7312
24FT7351
24FT7362
24FT7401
24FT7431
24FT7441
24FT7451
24FT7461
24FT7471
24G05271
24G05301
24H24411
24H35421
24H36621
24H36631
24H36641
24H36651
24H36661
24H36701
24H36811
24H36821
24H36861
24H37091
24H37131
24H37161
24H37191
24H37241
24H37341
24HS2561
24HS2581
24HS2591
24HS2601
24HS2621
24J15451
24J15731
24J15751
24J15761
24J15811
24J15821
24J15831
24J15841
24J15851
24J15861
CAP
LAMP COVER ASSY
FILTER ASSY A
FILTER ASSY B
TILT FOOT ASSY
SEPARATE BASE(SK) ASSY
DUCT CASE(SK)ASSY
INHAIL DUCT(SK)ASSY
COVER(INHAIL DUCT)ASSY
STOPPER (XDP)ASSY
PUSH BUTTON
PUSH BOTTON(TILT)
HALF NUT
GRIP
PLATE(FL)
PLATE(IT1)
PLATE(IT2)
PLATE(RL2)
PLATE(POL)
BRACKET(HANDLE)
STAY R
SPRING S
SHAFT(HANDLE)
SPRING(TILT)
BARRIER (LAMP BOX)
SHAFT PIN
BARRIER1(SEPARATE BASE)
BARRIER2(SEPARATE BASE)
BARRIER(XDP)
M18
M25
M12
M11
M15
M29
M02
M43
M30
M16
M17
M14
BRACKET(I/O)
BARRIER(LAMP BOX)ASSY
PLATE(FL)ASSY
M49
M47
M26
PLATE(RL2)ASSY
BRACKET(I/O)ASSY
DOUBLE FACE ADHESIVE TAPE
BARRIER(TILTFOOTR)
FILTER(COVER)A
FILTER(COVER)B
BARRIER
CUSHION (SEPARATE BASE)
CUSHION (DUCT CASE)
CUSHION (INHAIL DUCT)
CUSHION(INHAIL COVER)
CUSHION (FL)
10-4
VT440
*** APPEARANCE PARTS ***
24J15871
24J15971
24L34191
24L41311
24L43502
24L43951
24L43981
24L44721
24L44741
92203961
955X7161
955X7181
955X7191
955X7201
955X7211
955X7241
955X7251
955X7261
955Y1131
CUSHION (RL2)
BARRIER(B/M)
CAUTION LABEL(SERVICE)
CAUTION
CAUTION LABEL(LENS)
NAME PLATE(VT440)
LABEL(FUSE)
LABEL(INSTA CARE)
LABEL(VT LAMP)
TAPE,SCOTCH SUPER
LAMP BOX SASSY
R POL SASSY
G POL SASSY
B POL SASSY
FL SASSY
IT1 SASSY
IT2 SASSY
RL2 SASSY
OPT BASE SASSY
M01
E09
M36
M37
M38
M40
M41
M42
M39
M35
*** PRINTED & PACKING MATERIALS ***
M52
24M16261
24MU0181
24MU4771
24MU4781
24MU4931
24MU5511
24MU5521
70810792
78038751
78038771
78411391
79646751
79646941
ACCESSORY BAG
PROTECTION BAG
SPACER F
SPACER R
CARTON BOX
FILLER C,CARTON
PROTECTION BAG
POWER CORD U3 L3 BK,L(L)
QUICK REFERENCE VT540/440
WARRNTY CARD
USE'S MANUAL VT540/VT440
RD-366E
M52
M52
M52
M52
E10(M52)
M52
VT CABLE SET
*** VT CABLE SET ***
M52
M52
M52
M52
73499369
CABLE,RGB
ADAPTER D15P-MD15P
STRAP
70599172
24C05051
24C04534
PUSH RIVET
*** OPTION ***
REMOTE CONTROL KIT (98999243)
73499328
73499329
73499353
79644991
79645911
CABLE SERIAL TO PS/2
CABLE SERIAL TO MAC
CABLE SIGNAL (DIN8P-D9P)
UNIVERSAL IR RECIEVER(U)
REM-T HAND UNIT RD-355E
10-5
VT440G
2. VT440G
SYMBOL
PART NO
DESCRIPTION
*** PWB ASSYS ***
E01
E02
E03
E04
935Y1D01
935Y1F01
935X7NA1
935X7NB1
LCES PWB ASSY
MAIN PWB ASSY
I/O PWB ASSY
KEY PWB ASSY
*** ELECTRICAL PARTS & MISCELLANEOUS PARTS ***
E05
79646932
73895159
73895160
70ED2315
70ED2315
70ED2315
70ED2165
70ED2404
70ED2038
70ED2166
31700104
38102078
63099063
73W20077
73WLW001
64003036
64003037
64KA1118
64KA1122
64KA1140
65904524
65904524
65AB1116
65CF1506
65FK2102
66500003
66KA2008
POWER UNIT
CABLE,FFC 30P*38 P0.5 SO
CABLE,FFC 40P*38 P0.5 SO
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
FPC CONNE FH12-30S-0.5SH
CONNECTOR,FFC 40P
CONNECTOR,FPC 40P
SCIROCCO FAN
THERMISTOR104JT-075-90271
SPEAKER 40*28MM 8H 1W
CN2P(SP)220S,1685-26
CN22P(MK)60W,1685-26
CRYSTAL RESONATOR
CRYSTAL RESONATOR
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
CRYSTALOSCILLATOR33.33333
DETECTOR SWITCH
DETECTOR SWITCH
SW,SLIDE
POBES
POGES
PORES
POST
POST
POSV
POSV
E06
E07
X1101
X1100
X3501
X3502
X3503
SW3313
SW4100
SW3301
SWITCH,TACT
RELAY
THERMOSTAT
DETECTOR SWITCH
RL3100
E08
SW3312
10-6
VT440G
*** APPEARANCE PARTS ***
S05
S06
S11
S09
S07
S01
S08
S03
S12
S13
12851741
910E2511
24N04721
910E2521
910E2531
910E306L
24N04781
910D3066
91613061
91614031
24N03651
24N04352
24N04691
24N04701
24N04731
24N04741
24N04751
24N04761
24N04771
91052031
91283076
91613076
12J00291
12J00301
12J00351
12J00361
12J00371
12J00381
12J00391
12J00401
12J00411
12J00421
12JS1351
12JS1361
12JS1371
12JS1381
12JS1391
12JS1431
12JS1441
12JS1451
OR 12JS1471
12JS1481
OR 12JS1491
12JS1501
12JS1511
12JS1521
SPECIAL SCREW(PL-HM2.5*6)
PL-CPIMS*2.5*6*15BF
SCREW(WASCHER 2.5*10)
PL-CPIMS*2.5*8*15BF
PL-CPIMS*2.5*10*15BF
PL-CPIMS*3*10*3GF
SPECIAL SCREW(PL-HM3*16)
PL-CPIMS*3*10*3KF
SCREW,#2CBTS*3*10*15BF
SCREW,#2CBITS*4*12*15BF
STUD(D-SUB,M2.6*3GF)
SPECIAL SCREW(M4)
STAD(M3*14,M/FM)
S02
S10
STAD(M3*17.5,M/FM)
SCREW(CBIPS2*6,PRECOAT)
SCREW(CFIPS3*6*15BF)
SPECIAL SCREW(HLSS4*6)
SCREW(PL-HHIMS2*5)
SCREW(CBIPS 3*10*15BF)
CFIMS2*6*15BF
SCREW,#2CPTS*3*12*3KF
SCREW,#2CBTS*3*12*3KF
CROSS PRISM(SKN)
S14
S04
CROSS PRISM(SKF)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
FIELD LENS(SK)
CONDENSER LENS 1(SK)
CONDENSER LENS 2(SK)
RELAY LENS 1(SK)
RELAY LENS 2(SK)
MIRROR 1(SK)
M48
FIELD LENS ASSY(SK)
CONDENSER LENS ASSY1(SK)
CONDENSER LENS ASSY2(SK)
RELAY LENS ASSY1(SK)
RELAY LENS ASSY2(SK)
ZOOM LENS(SK)
INTEGRATOR1(SKA)
INTEGRATOR2(SKA)
INTEGRATOR2(SKA)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
MIRROR 0(SK)
MIRROR ASSY1(SK)
MIRROR 2(SK)
M05
M46
M44
M06
M07
M08
10-7
VT440G
*** APPEARANCE PARTS ***
M09
M10
12JS1531
12JS1541
12JS1551
12JS1561
12JS1571
12JS1581
12JS1601
12JS1711
12JS1721
18775141
25765841
25781322
24BS6621
24C02681
24C05911
24D11271
24D11421
24DT7492
24DT7665
24F29461
24F30581
24F31771
24F31781
24F31791
24F31801
24F31811
24F31821
24F31861
24F31871
24F31881
24F31901
24F31921
24F31931
24F31941
24F31951
24F31971
24F31981
24F31991
24F32011
24F32021
24F32031
24F32041
24F32051
24F32061
24F32071
24F32081
DICHROIC MIRROR 1(SK)
DICHROIC MIRROR 2(SK)
POLARIZER 1(SK)
POLARIZER 2(SK)
POLARIZER 3(SK)
REFLCTER LAMP(SK)
COVER GLASS(SK)
POLARIZER 3(SKK)
MIRROR ASSY1(SKT)
LABEL,SERIAL MANUFACTURE
LABEL(1*10)
LABEL,BARCODE
REMOCON CASE UNIT
CLIP(DS-9UL)
M19
TILT RIVET
BOTTOM COVER
TOP COVER(VT440)
BOTTOM COVER ASSY
TOP COVER ASSY
TILT FOOT(R)
CUSHION FOOT(R)
HOLDER(CL1)
HOLDER(CL2)
HOLDER(FL)
HOLDER(RL1)
HOLDER(RL2)
HOLDER(M1)
INDICATOR
FILTER F
TILT FOOT F
HANDLE
CUSHION (FRONTFOOT)
LAMP COVER
FILTER CASE A
FILTER CASE B
SPEAKER HOLDER
FILTER S
M45
M03
M20
M28
M22
M23
FILTER R
SEPARATE BASE(SK)
COVER OPT(SK)
DUCT CASE(SK)
INHAIL DUCT(SK)
COVER(INHAIL DUCT)
STOPPER(XDP)
LAMP BOX(F)
M13
LAMP BOX(T)
10-8
VT440G
*** APPEARANCE PARTS ***
24F32091
24F32561
24FT6951
24FT7312
24FT7351
24FT7362
24FT7401
24FT7431
24FT7441
24FT7451
24FT7461
24FT7471
24G05271
24G05301
24H24411
24H35421
24H36621
24H36631
24H36641
24H36651
24H36661
24H36701
24H36811
24H36821
24H36861
24H37091
24H37131
24H37161
24H37191
24H37241
24H37341
24HS2561
24HS2581
24HS2591
24HS2601
24HS2621
24J15451
24J15731
24J15751
24J15761
24J15811
24J15821
24J15831
24J15841
24J15851
24J15861
LAMP BOX(B)
TILTINSERT
CAP
M24
M04
M21
M27
LAMP COVER ASSY
FILTER ASSY A
FILTER ASSY B
TILT FOOT ASSY
SEPARATE BASE(SK) ASSY
DUCT CASE(SK)ASSY
INHAIL DUCT(SK)ASSY
COVER(INHAIL DUCT)ASSY
STOPPER (XDP)ASSY
PUSH BUTTON
PUSH BOTTON(TILT)
HALF NUT
GRIP
PLATE(FL)
PLATE(IT1)
PLATE(IT2)
PLATE(RL2)
PLATE(POL)
BRACKET(HANDLE)
STAY R
SPRING S
SHAFT(HANDLE)
SPRING(TILT)
BARRIER (LAMP BOX)
SHAFT PIN
BARRIER1(SEPARATE BASE)
BARRIER2(SEPARATE BASE)
BARRIER(XDP)
M18
M25
M12
M11
M15
M29
M02
M43
M30
M16
M17
M14
BRACKET(I/O)
BARRIER(LAMP BOX)ASSY
PLATE(FL)ASSY
M49
M47
M26
PLATE(RL2)ASSY
BRACKET(I/O)ASSY
DOUBLE FACE ADHESIVE TAPE
BARRIER(TILTFOOTR)
FILTER(COVER)A
FILTER(COVER)B
BARRIER
CUSHION (SEPARATE BASE)
CUSHION (DUCT CASE)
CUSHION (INHAIL DUCT)
CUSHION(INHAIL COVER)
CUSHION (FL)
10-9
VT440G
*** APPEARANCE PARTS ***
24J15871
CUSHION (RL2)
M01
24J15971
24L34191
24L41311
24L43502
24L43961
24L43981
24L44021
24L44721
24L44741
24L44971
24L45001
92203961
955X7161
955X7181
955X7191
955X7201
955X7211
955X7241
955X7251
955X7261
955Y1131
BARRIER(B/M)
CAUTION LABEL(SERVICE)
CAUTION
CAUTION LABEL(LENS)
NAME PLATE(VT440G)
LABEL(FUSE)
EAN LABEL
LABEL(INSTA CARE)
LABEL(VT LAMP)
LABEL(LENZ)
LABEL(3.5*20)
TAPE,SCOTCH SUPER
E09
M36
M37
M38
M40
M41
M42
M39
M35
*** PRINTED & PACKING MATERIALS ***
M52
24M16261
24MU4771
24MU4781
24MU4941
24MU5511
24MU5521
70810004
78038751
78038771
78411391
79646751
79646941
ACCESSORY BAG
SPACER F
SPACER R
CARTON BOX
FILLER C,CARTON
PROTECTION BAG
POWER CORD E3 L3 BK,L(L)
QUICK REFERENCE VT540/440
WARRNTY CARD
USE'S MANUAL VT540/VT440
RD-366E
M52
M52
M52
E10(M52)
M52
VT CABLE SET
*** VT CABLE SET ***
M52
M52
M52
M52
73499369
CABLE,RGB
ADAPTER D15P-MD15P
STRAP
70599172
24C05051
24C04534
PUSH RIVET
*** OPTION ***
REMOTE CONTROL KIT (98999243)
73499328
73499329
73499353
79644991
79645911
CABLE SERIAL TO PS/2
CABLE SERIAL TO MAC
CABLE SIGNAL (DIN8P-D9P)
UNIVERSAL IR RECIEVER(U)
REM-T HAND UNIT RD-355E
10-10
VT540
3. VT540
SYMBOL
PART NO
DESCRIPTION
*** PWB ASSYS ***
E01
E02
E03
E04
935X7D01
935X7F01
935X7NA1
935X7NB1
LCEX PWB ASSY
MAIN PWB ASSY
I/O PWB ASSY
KEY PWB ASSY
*** ELECTRICAL PARTS & MISCELLANEOUS PARTS ***
E05
79646932
73895159
73895160
70ED2315
70ED2315
70ED2315
70ED2165
70ED2404
70ED2038
70ED2166
31700104
38102078
63099063
73W20077
73WLW001
64003036
64003037
64KA1118
64KA1122
64KA1140
65904524
65904524
65AB1116
65CF1506
65FK2102
66500003
66KA2008
POWER UNIT
CABLE,FFC 30P*38 P0.5 SO
CABLE,FFC 40P*38 P0.5 SO
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
FPC CONNE FH12-30S-0.5SH
CONNECTOR,FFC 40P
CONNECTOR,FPC 40P
SCIROCCO FAN
THERMISTOR104JT-075-90271
SPEAKER 40*28MM 8H 1W
CN2P(SP)220S,1685-26
CN22P(MK)60W,1685-26
CRYSTAL RESONATOR
CRYSTAL RESONATOR
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
CRYSTALOSCILLATOR33.33333
DETECTOR SWITCH
DETECTOR SWITCH
SW,SLIDE
POBES
POGES
PORES
POST
POST
POSV
POSV
E06
E07
X1101
X1100
X3501
X3502
X3503
SW3313
SW4100
SW3301
SWITCH,TACT
RELAY
THERMOSTAT
DETECTOR SWITCH
RL3100
E08
SW3312
10-11
VT540
*** APPEARANCE PARTS ***
S05
S06
S11
S09
S07
S01
S08
S03
S12
S13
12851741
910E2511
24N04721
910E2521
910E2531
910E306L
24N04781
910D3066
91613061
91614031
24N03651
24N04352
24N04691
24N04701
24N04731
24N04741
24N04751
24N04761
24N04771
91052031
91283076
91613076
12J00291
12J00301
12J00351
12J00361
12J00371
12J00381
12J00391
12J00401
12J00411
12J00421
12JS1351
12JS1361
12JS1371
12JS1381
12JS1391
12JS1431
12JS1441
12JS1451
OR 12JS1471
12JS1481
OR 12JS1491
12JS1501
12JS1511
12JS1521
SPECIAL SCREW(PL-HM2.5*6)
PL-CPIMS*2.5*6*15BF
SCREW(WASCHER 2.5*10)
PL-CPIMS*2.5*8*15BF
PL-CPIMS*2.5*10*15BF
PL-CPIMS*3*10*3GF
SPECIAL SCREW(PL-HM3*16)
PL-CPIMS*3*10*3KF
SCREW,#2CBTS*3*10*15BF
SCREW,#2CBITS*4*12*15BF
STUD(D-SUB,M2.6*3GF)
SPECIAL SCREW(M4)
STAD(M3*14,M/FM)
S02
S10
STAD(M3*17.5,M/FM)
SCREW(CBIPS2*6,PRECOAT)
SCREW(CFIPS3*6*15BF)
SPECIAL SCREW(HLSS4*6)
SCREW(PL-HHIMS2*5)
SCREW(CBIPS 3*10*15BF)
CFIMS2*6*15BF
SCREW,#2CPTS*3*12*3KF
SCREW,#2CBTS*3*12*3KF
CROSS PRISM(SKN)
S14
S04
CROSS PRISM(SKF)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
FIELD LENS(SK)
CONDENSER LENS 1(SK)
CONDENSER LENS 2(SK)
RELAY LENS 1(SK)
RELAY LENS 2(SK)
MIRROR 1(SK)
M48
FIELD LENS ASSY(SK)
CONDENSER LENS ASSY1(SK)
CONDENSER LENS ASSY2(SK)
RELAY LENS ASSY1(SK)
RELAY LENS ASSY2(SK)
ZOOM LENS(SK)
INTEGRATOR1(SKA)
INTEGRATOR2(SKA)
INTEGRATOR2(SKA)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
MIRROR 0(SK)
MIRROR ASSY1(SK)
MIRROR 2(SK)
M05
M46
M44
M06
M07
M08
10-12
VT540
*** APPEARANCE PARTS ***
M09
M10
12JS1531
12JS1541
12JS1551
12JS1561
12JS1571
12JS1581
12JS1601
12JS1711
12JS1721
18775141
25765841
25781322
24BS6621
24C02681
24C05911
24D11271
24D11261
24DT7492
24DT7485
24F29461
24F30581
24F31771
24F31781
24F31791
24F31801
24F31811
24F31821
24F31861
24F31871
24F31881
24F31901
24F31921
24F31931
24F31941
24F31951
24F31971
24F31981
24F31991
24F32011
24F32021
24F32031
24F32041
24F32051
24F32061
24F32071
24F32081
DICHROIC MIRROR 1(SK)
DICHROIC MIRROR 2(SK)
POLARIZER 1(SK)
POLARIZER 2(SK)
POLARIZER 3(SK)
REFLCTER LAMP(SK)
COVER GLASS(SK)
POLARIZER 3(SKK)
MIRROR ASSY1(SKT)
LABEL,SERIAL MANUFACTURE
LABEL(1*10)
LABEL,BARCODE
REMOCON CASE UNIT
CLIP(DS-9UL)
M19
TILT RIVET
BOTTOM COVER
TOP COVER(VT540)
BOTTOM COVER ASSY
TOP COVER ASSY
TILT FOOT(R)
CUSHION FOOT(R)
HOLDER(CL1)
HOLDER(CL2)
HOLDER(FL)
HOLDER(RL1)
HOLDER(RL2)
HOLDER(M1)
INDICATOR
FILTER F
TILT FOOT F
HANDLE
CUSHION (FRONTFOOT)
LAMP COVER
FILTER CASE A
FILTER CASE B
SPEAKER HOLDER
FILTER S
M45
M03
M20
M22
M23
FILTER R
SEPARATE BASE(SK)
COVER OPT(SK)
DUCT CASE(SK)
INHAIL DUCT(SK)
COVER(INHAIL DUCT)
STOPPER(XDP)
LAMP BOX(F)
M13
LAMP BOX(T)
10-13
VT540
*** APPEARANCE PARTS ***
24F32091
24F32561
LAMP BOX(B)
TILTINSERT
M24
M04
M21
M27
24FT6951
24FT7311
24FT7351
24FT7361
24FT7401
24FT7431
24FT7441
24FT7451
24FT7461
24FT7471
24G05271
24G05301
24H24411
24H35421
24H36621
24H36631
24H36641
24H36651
24H36661
24H36701
24H36811
24H36821
24H36861
24H37091
24H37131
24H37161
24H37191
24H37241
24H37341
24HS2561
24HS2581
24HS2591
24HS2601
24HS2621
24J15451
24J15731
24J15751
24J15761
24J15811
24J15821
24J15831
24J15841
24J15851
24J15861
CAP
LAMP COVER ASSY
FILTER ASSY A
FILTER ASSY B
TILT FOOT ASSY
SEPARATE BASE(SK) ASSY
DUCT CASE(SK)ASSY
INHAIL DUCT(SK)ASSY
COVER(INHAIL DUCT)ASSY
STOPPER (XDP)ASSY
PUSH BUTTON
PUSH BOTTON(TILT)
HALF NUT
GRIP
PLATE(FL)
PLATE(IT1)
PLATE(IT2)
PLATE(RL2)
PLATE(POL)
BRACKET(HANDLE)
STAY R
SPRING S
SHAFT(HANDLE)
SPRING(TILT)
BARRIER (LAMP BOX)
SHAFT PIN
BARRIER1(SEPARATE BASE)
BARRIER2(SEPARATE BASE)
BARRIER(XDP)
M18
M25
M12
M11
M15
M29
M02
M43
M30
M16
M17
M14
BRACKET(I/O)
BARRIER(LAMP BOX)ASSY
PLATE(FL)ASSY
M49
M47
M26
PLATE(RL2)ASSY
BRACKET(I/O)ASSY
DOUBLE FACE ADHESIVE TAPE
BARRIER(TILTFOOTR)
FILTER(COVER)A
FILTER(COVER)B
BARRIER
CUSHION (SEPARATE BASE)
CUSHION (DUCT CASE)
CUSHION (INHAIL DUCT)
CUSHION(INHAIL COVER)
CUSHION (FL)
10-14
VT540
*** APPEARANCE PARTS ***
24J15871
24J15971
24L34191
24L41311
24L43502
24L43921
24L43981
24L44721
24L44741
92203961
955X7161
955X7181
955X7191
955X7201
955X7211
955X7241
955X7251
955X7261
955Y7131
CUSHION (RL2)
BARRIER(B/M)
M01
CAUTION LABEL(SERVICE)
CAUTION
CAUTION LABEL(LENS)
NAME PLATE(VT540)
LABEL(FUSE)
LABEL(INSTA CARE)
LABEL(VT LAMP)
TAPE,SCOTCH SUPER
E09
M36
M37
M38
M40
M41
M42
M39
M35
*** PRINTED & PACKING MATERIALS ***
M52
24M16261
24MU0181
24MU4771
24MU4781
24MU4901
24MU5511
24MU5521
70810792
78038751
78038771
78411391
79646751
79646941
ACCESSORY BAG
PROTECTION BAG
SPACER F
SPACER R
CARTON BOX
FILLER C,CARTON
PROTECTION BAG
POWER CORD U3 L3 BK,L(L)
QUICK REFERENCE VT540/440
WARRNTY CARD
USE'S MANUAL VT540/VT440
RD-366E
M52
M52
M52
M52
E10(M52)
M52
VT CABLE SET
*** VT CABLE SET ***
M52
M52
M52
M52
73499369
CABLE,RGB
ADAPTER D15P-MD15P
STRAP
70599172
24C05051
24C04534
PUSH RIVET
*** OPTION ***
REMOTE CONTROL KIT (98999243)
73499328
73499329
73499353
79644991
79645911
CABLE SERIAL TO PS/2
CABLE SERIAL TO MAC
CABLE SIGNAL (DIN8P-D9P)
UNIVERSAL IR RECIEVER(U)
REM-T HAND UNIT RD-355E
10-15
VT540G
4. VT540G
SYMBOL
PART NO
DESCRIPTION
*** PWB ASSYS ***
E01
E02
E03
E04
935X7D01
935X7F01
935X7NA1
935X7NB1
LCEX PWB ASSY
MAIN PWB ASSY
I/O PWB ASSY
KEY PWB ASSY
*** ELECTRICAL PARTS & MISCELLANEOUS PARTS ***
E05
79646932
73895159
73895160
70ED2315
70ED2315
70ED2315
70ED2165
70ED2404
70ED2038
70ED2166
31700104
38102078
63099063
73W20077
73WLW001
64003036
64003037
64KA1118
64KA1122
64KA1140
65904524
65904524
65AB1116
65CF1506
65FK2102
66500003
66KA2008
POWER UNIT
CABLE,FFC 30P*38 P0.5 SO
CABLE,FFC 40P*38 P0.5 SO
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
FPC CONNE FH12-30S-0.5SH
CONNECTOR,FFC 40P
CONNECTOR,FPC 40P
SCIROCCO FAN
THERMISTOR104JT-075-90271
SPEAKER 40*28MM 8H 1W
CN2P(SP)220S,1685-26
CN22P(MK)60W,1685-26
CRYSTAL RESONATOR
CRYSTAL RESONATOR
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
CRYSTALOSCILLATOR33.33333
DETECTOR SWITCH
DETECTOR SWITCH
SW,SLIDE
POBES
POGES
PORES
POST
POST
POSV
POSV
E06
E07
X1101
X1100
X3501
X3502
X3503
SW3313
SW4100
SW3301
SWITCH,TACT
RELAY
THERMOSTAT
DETECTOR SWITCH
RL3100
E08
SW3312
10-16
VT540G
*** APPEARANCE PARTS ***
S05
S06
S11
S09
S07
S01
S08
S03
S12
S13
12851741
910E2511
24N04721
910E2521
910E2531
910E306L
24N04781
910D3066
91613061
91614031
24N03651
24N04352
24N04691
24N04701
24N04731
24N04741
24N04751
24N04761
24N04771
91052031
91283076
91613076
12J00291
12J00301
12J00351
12J00361
12J00371
12J00381
12J00391
12J00401
12J00411
12J00421
12JS1351
12JS1361
12JS1371
12JS1381
12JS1391
12JS1431
12JS1441
12JS1451
12JS1471
12JS1481
12JS1491
12JS1501
12JS1511
12JS1521
SPECIAL SCREW(PL-HM2.5*6)
PL-CPIMS*2.5*6*15BF
SCREW(WASCHER 2.5*10)
PL-CPIMS*2.5*8*15BF
PL-CPIMS*2.5*10*15BF
PL-CPIMS*3*10*3GF
SPECIAL SCREW(PL-HM3*16)
PL-CPIMS*3*10*3KF
SCREW,#2CBTS*3*10*15BF
SCREW,#2CBITS*4*12*15BF
STUD(D-SUB,M2.6*3GF)
SPECIAL SCREW(M4)
STAD(M3*14,M/FM)
S02
S10
STAD(M3*17.5,M/FM)
SCREW(CBIPS2*6,PRECOAT)
SCREW(CFIPS3*6*15BF)
SPECIAL SCREW(HLSS4*6)
SCREW(PL-HHIMS2*5)
SCREW(CBIPS 3*10*15BF)
CFIMS2*6*15BF
SCREW,#2CPTS*3*12*3KF
SCREW,#2CBTS*3*12*3KF
CROSS PRISM(SKN)
S14
S04
CROSS PRISM(SKF)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
FIELD LENS(SK)
CONDENSER LENS 1(SK)
CONDENSER LENS 2(SK)
RELAY LENS 1(SK)
RELAY LENS 2(SK)
MIRROR 1(SK)
M48
FIELD LENS ASSY(SK)
CONDENSER LENS ASSY1(SK)
CONDENSER LENS ASSY2(SK)
RELAY LENS ASSY1(SK)
RELAY LENS ASSY2(SK)
ZOOM LENS(SK)
INTEGRATOR1(SKA)
INTEGRATOR2(SKA)
INTEGRATOR2(SKA)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
MIRROR 0(SK)
MIRROR ASSY1(SK)
MIRROR 2(SK)
M05
M46
M44
M06
M07
M08
10-17
VT540G
*** APPEARANCE PARTS ***
M09
M10
12JS1531
12JS1541
12JS1551
12JS1561
12JS1571
12JS1581
12JS1601
12JS1711
12JS1721
18775141
25765841
25781322
24BS6621
24C02681
24C05911
24D11271
24D11261
24DT7492
24DT7485
24F29461
24F30581
24F31771
24F31781
24F31791
24F31801
24F31811
24F31821
24F31861
24F31871
24F31881
24F31901
24F31921
24F31931
24F31941
24F31951
24F31971
24F31981
24F31991
24F32011
24F32021
24F32031
24F32041
24F32051
24F32061
24F32071
24F32081
DICHROIC MIRROR 1(SK)
DICHROIC MIRROR 2(SK)
POLARIZER 1(SK)
POLARIZER 2(SK)
POLARIZER 3(SK)
REFLCTER LAMP(SK)
COVER GLASS(SK)
POLARIZER 3(SKK)
MIRROR ASSY1(SKT)
LABEL,SERIAL MANUFACTURE
LABEL(1*10)
LABEL,BARCODE
REMOCON CASE UNIT
CLIP(DS-9UL)
M19
TILT RIVET
BOTTOM COVER
TOP COVER(VT540)
BOTTOM COVER ASSY
TOP COVER ASSY
TILT FOOT(R)
CUSHION FOOT(R)
HOLDER(CL1)
HOLDER(CL2)
HOLDER(FL)
HOLDER(RL1)
HOLDER(RL2)
HOLDER(M1)
INDICATOR
FILTER F
TILT FOOT F
HANDLE
CUSHION (FRONTFOOT)
LAMP COVER
FILTER CASE A
FILTER CASE B
SPEAKER HOLDER
FILTER S
M45
M03
M20
M28
M22
M23
FILTER R
SEPARATE BASE(SK)
COVER OPT(SK)
DUCT CASE(SK)
INHAIL DUCT(SK)
COVER(INHAIL DUCT)
STOPPER(XDP)
LAMP BOX(F)
M13
LAMP BOX(T)
10-18
VT540G
*** APPEARANCE PARTS ***
24F32091
24F32561
24FT6951
24FT7311
24FT7351
24FT7361
24FT7401
24FT7431
24FT7441
24FT7451
24FT7461
24FT7471
24G05271
24G05301
24H24411
24H35421
24H36621
24H36631
24H36641
24H36651
24H36661
24H36701
24H36811
24H36821
24H36861
24H37091
24H37131
24H37161
24H37191
24H37241
24H37341
24HS2561
24HS2581
24HS2591
24HS2601
24HS2621
24J15451
24J15731
24J15751
24J15761
24J15811
24J15821
24J15831
24J15841
24J15851
24J15861
LAMP BOX(B)
TILTINSERT
CAP
M24
M04
M21
M27
LAMP COVER ASSY
FILTER ASSY A
FILTER ASSY B
TILT FOOT ASSY
SEPARATE BASE(SK) ASSY
DUCT CASE(SK)ASSY
INHAIL DUCT(SK)ASSY
COVER(INHAIL DUCT)ASSY
STOPPER (XDP)ASSY
PUSH BUTTON
PUSH BOTTON(TILT)
HALF NUT
GRIP
PLATE(FL)
PLATE(IT1)
PLATE(IT2)
PLATE(RL2)
PLATE(POL)
BRACKET(HANDLE)
STAY R
SPRING S
SHAFT(HANDLE)
SPRING(TILT)
BARRIER (LAMP BOX)
SHAFT PIN
BARRIER1(SEPARATE BASE)
BARRIER2(SEPARATE BASE)
BARRIER(XDP)
M18
M25
M12
M11
M15
M29
M02
M43
M30
M16
M17
M14
BRACKET(I/O)
BARRIER(LAMP BOX)ASSY
PLATE(FL)ASSY
M49
M47
M26
PLATE(RL2)ASSY
BRACKET(I/O)ASSY
DOUBLE FACE ADHESIVE TAPE
BARRIER(TILTFOOTR)
FILTER(COVER)A
FILTER(COVER)B
BARRIER
CUSHION (SEPARATE BASE)
CUSHION (DUCT CASE)
CUSHION (INHAIL DUCT)
CUSHION(INHAIL COVER)
CUSHION (FL)
10-19
VT540G
*** APPEARANCE PARTS ***
24J15871
CUSHION (RL2)
M01
24J15971
24L34191
24L41311
24L43502
24L43931
24L43981
24L44021
24L44721
24L44741
24L44971
24L45001
92203961
955X7161
955X7181
955X7191
955X7201
955X7211
955X7241
955X7251
955X7261
955Y7131
BARRIER(B/M)
CAUTION LABEL(SERVICE)
CAUTION
CAUTION LABEL(LENS)
NAME PLATE(VT540G)
LABEL(FUSE)
EAN LABEL
LABEL(INSTA CARE)
LABEL(VT LAMP)
LABEL(LENZ)
LABEL(3.5*20)
TAPE,SCOTCH SUPER
E09
M36
M37
M38
M40
M41
M42
M39
M35
*** PRINTED & PACKING MATERIALS ***
M52
24M16261
24MU4771
24MU4781
24MU4911
24MU5511
24MU5521
70810004
78038751
78038771
78411391
79646751
79646941
ACCESSORY BAG
SPACER F
SPACER R
CARTON BOX
FILLER C,CARTON
PROTECTION BAG
POWER CORD E3 L3 BK,L(L)
QUICK REFERENCE VT540/440
WARRNTY CARD
USE'S MANUAL VT540/VT440
RD-366E
M52
M52
M52
M52
E10(M52)
M52
VT CABLE SET
*** VT CABLE SET ***
M52
M52
M52
M52
73499369
CABLE,RGB
ADAPTER D15P-MD15P
STRAP
70599172
24C05051
24C04534
PUSH RIVET
*** OPTION ***
REMOTE CONTROL KIT (98999243)
73499328
73499329
73499353
79644991
79645911
CABLE SERIAL TO PS/2
CABLE SERIAL TO MAC
CABLE SIGNAL (DIN8P-D9P)
UNIVERSAL IR RECIEVER(U)
REM-T HAND UNIT RD-355E
10-20
VT440J
5. VT440J
SYMBOL
PART NO
DESCRIPTION
*** PWB ASSYS ***
E01
E02
E03
E04
935Y1D01
935Y1F01
935Y1NA1
935Y1NB1
LCES PWB ASSY
MAIN PWB ASSY
I/O PWB ASSY
KEY PWB ASSY
*** ELECTRICAL PARTS & MISCELLANEOUS PARTS ***
E05
CN1
CN2
79646932
73895164
73895165
70ED2315
70ED2315
70ED2315
70ED2165
70ED2404
70ED2038
70ED2166
31700104
38102078
63099063
73W20077
73WLW001
64003036
64003037
64KA1118
64KA1122
64KA1140
65904524
65904524
65AB1116
65CF1506
65FK2102
66500003
66KA2008
POWER UNIT
CABLE,FFC 30P*38 P0.5 SU
CABLE,FFC 40P*38 P0.5 SU
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
FPC CONNE FH12-30S-0.5SH
CONNECTOR,FFC 40P
CONNECTOR,FPC 40P
SCIROCCO FAN
THERMISTOR104JT-075-90271
SPEAKER 40*28MM 8H 1W
CN2P(SP)220S,1685-26
CN22P(MK)60W,1685-26
CRYSTAL RESONATOR
CRYSTAL RESONATOR
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
CRYSTALOSCILLATOR33.33333
DETECTOR SWITCH
DETECTOR SWITCH
SW,SLIDE
POBES
POGES
PORES
POST
POST
POSV
POSV
E06
E07
X1101
X1100
X3501
X3502
X3503
SW3313
SW4100
SW3301
SWITCH,TACT
RELAY
THERMOSTAT
DETECTOR SWITCH
RL3100
E08
SW3312
10-21
VT440J
*** APPEARANCE PARTS ***
S05
S06
S11
S09
S07
S01
S08
S03
S12
S13
12851741
910E2511
24N04721
910E2521
910E2531
910E306L
24N04781
910D3066
91613061
91614031
24N03651
24N04352
24N04691
24N04701
24N04731
24N04741
24N04751
24N04761
24N04771
91052031
91283076
91613076
12J00291
12J00301
12J00351
12J00361
12J00371
12J00381
12J00391
12J00401
12J00411
12J00421
12JS1351
12JS1361
12JS1371
12JS1381
12JS1391
12JS1431
12JS1441
12JS1451
OR 12JS1471
12JS1481
OR 12JS1491
12JS1501
12JS1511
12JS1521
SPECIAL SCREW(PL-HM2.5*6)
PL-CPIMS*2.5*6*15BF
SCREW(WASCHER 2.5*10)
PL-CPIMS*2.5*8*15BF
PL-CPIMS*2.5*10*15BF
PL-CPIMS*3*10*3GF
SPECIAL SCREW(PL-HM3*16)
PL-CPIMS*3*10*3KF
SCREW,#2CBTS*3*10*15BF
SCREW,#2CBITS*4*12*15BF
STUD(D-SUB,M2.6*3GF)
SPECIAL SCREW(M4)
STAD(M3*14,M/FM)
S02
S10
STAD(M3*17.5,M/FM)
SCREW(CBIPS2*6,PRECOAT)
SCREW(CFIPS3*6*15BF)
SPECIAL SCREW(HLSS4*6)
SCREW(PL-HHIMS2*5)
SCREW(CBIPS 3*10*15BF)
CFIMS2*6*15BF
SCREW,#2CPTS*3*12*3KF
SCREW,#2CBTS*3*12*3KF
CROSS PRISM(SKN)
S14
S04
CROSS PRISM(SKF)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
FIELD LENS(SK)
CONDENSER LENS 1(SK)
CONDENSER LENS 2(SK)
RELAY LENS 1(SK)
RELAY LENS 2(SK)
MIRROR 1(SK)
M48
FIELD LENS ASSY(SK)
CONDENSER LENS ASSY1(SK)
CONDENSER LENS ASSY2(SK)
RELAY LENS ASSY1(SK)
RELAY LENS ASSY2(SK)
ZOOM LENS(SK)
INTEGRATOR1(SKA)
INTEGRATOR2(SKA)
INTEGRATOR2(SKA)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
MIRROR 0(SK)
MIRROR ASSY1(SK)
MIRROR 2(SK)
M05
M46
M44
M06
M07
M08
10-22
VT440J
*** APPEARANCE PARTS ***
M09
M10
12JS1531
12JS1541
12JS1551
12JS1561
12JS1571
12JS1581
12JS1601
12JS1711
12JS1721
25617801
24BS6621
24C02681
24C05911
24C05601
24D11431
24DT7492
24DT7675
24F29461
24F30581
24F31771
24F31781
24F31791
24F31801
24F31811
24F31821
24F31861
24F31871
24F31881
24F31901
24F31921
24F31931
24F31941
24F31951
24F31971
24F31981
24F31991
24F32011
24F32021
24F32031
24F32041
24F32051
24F32061
24F32071
24F32081
24F32091
24F32601
DICHROIC MIRROR 1(SK)
DICHROIC MIRROR 2(SK)
POLARIZER 1(SK)
POLARIZER 2(SK)
POLARIZER 3(SK)
REFLCTER LAMP(SK)
COVER GLASS(SK)
POLARIZER 3(SKK)
MIRROR ASSY1(SKT)
TAPE FORM
M19
REMOCON CASE UNIT
CLIP(DS-9UL)
TILT RIVET
SPLIT PIN
TOP COVER(VT440J)
BOTTOM COVER ASSY
TOP COVER ASSY
TILT FOOT(R)
CUSHION FOOT(R)
HOLDER(CL1)
HOLDER(CL2)
HOLDER(FL)
HOLDER(RL1)
HOLDER(RL2)
HOLDER(M1)
INDICATOR
FILTER F
TILT FOOT F
HANDLE
CUSHION (FRONTFOOT)
LAMP COVER
FILTER CASE A
FILTER CASE B
SPEAKER HOLDER
FILTER S
M45
M03
M20
M28
M22
M23
FILTER R
SEPARATE BASE(SK)
COVER OPT(SK)
DUCT CASE(SK)
INHAIL DUCT(SK)
COVER(INHAIL DUCT)
STOPPER(XDP)
LAMP BOX(F)
LAMP BOX(T)
LAMP BOX(B)
WASHER(LAMP)
M13
10-23
VT440J
*** APPEARANCE PARTS ***
M24
M04
M21
M27
24FT6951
24FT7312
24FT7351
24FT7362
24FT7401
24FT7431
24FT7441
24FT7451
24FT7461
24FT7471
24G05271
24G05301
24H24411
24H35421
24H36621
24H36631
24H36641
24H36651
24H36661
24H36701
24H36741
24H36811
24H36821
24H36861
24H37091
24H37131
24H37191
24H37241
24H37321
24H37331
24H37341
24HS2581
24HS2591
24HS2601
24HS2621
24J15341
24J15451
24J15731
24J15751
24J15761
24J15811
24J15821
24J15831
24J15841
24J15851
24J15861
CAP
LAMP COVER ASSY
FILTER ASSY A
FILTER ASSY B
TILT FOOT ASSY
SEPARATE BASE(SK) ASSY
DUCT CASE(SK)ASSY
INHAIL DUCT(SK)ASSY
COVER(INHAIL DUCT)ASSY
STOPPER (XDP)ASSY
PUSH BUTTON
PUSH BOTTON(TILT)
HALF NUT
GRIP
PLATE(FL)
PLATE(IT1)
PLATE(IT2)
PLATE(RL2)
PLATE(POL)
BRACKET(HANDLE)
TERMINAL BOARD
STAY R
SPRING S
SHAFT(HANDLE)
SPRING(TILT)
BARRIER (LAMP BOX)
BARRIER1(SEPARATE BASE)
BARRIER2(SEPARATE BASE)
BARRIER(LAMP COVER)
PLATE(I/O)
BARRIER(XDP)
BARRIER(LAMP BOX)ASSY
PLATE(FL)ASSY
PLATE(RL2)ASSY
BRACKET(I/O)ASSY
BARRIER(TOP)
DOUBLE FACE ADHESIVE TAPE
BARRIER(TILTFOOTR)
FILTER(COVER)A
FILTER(COVER)B
BARRIER
CUSHION (SEPARATE BASE)
CUSHION (DUCT CASE)
CUSHION (INHAIL DUCT)
CUSHION(INHAIL COVER)
CUSHION (FL)
M18
M25
M12
M11
M15
M29
M02
M43
M30
M16
M17
M14
M49
M47
M26
10-24
VT440J
*** APPEARANCE PARTS ***
24J15871
24J15961
24J15971
24J15981
24J15991
24J16021
24J16041
24K24401
24L11331
24L34401
24L41311
24L42201
24L43971
24L44001
24L44741
24L44981
24L45001
92203961
955X7161
955X7181
955X7191
955X7201
955X7211
955X7241
955X7251
955X7261
955Y1131
CUSHION (RL2)
CUSHION2(INHAIL DUCT)
BARRIER(B/M)
SHEET A(SP)
M01
SHEET B(SP)
CUSHION(FILTER)
CUSHION(10*6.5*T13)
INLAY(I/O)
LABEL(8*28)
CAUTION LABEL(SERVICE)
CAUTION
CAUTION LABEL(EARTH)
NAME PLATE
LABEL POS
LABEL(VT LAMP)
LABEL(LENS)
LABEL(3.5*20)
TAPE SCOTCH SUPER
LAMP BOX SASSY
R POL SASSY
G POL SASSY
B POL SASSY
FL SASSY
IT1 SASSY
IT2 SASSY
RL2 SASSY
E09
M36
M37
M38
M40
M41
M42
M39
M35
OPT BASE SASSY
10-25
VT440J
*** PRINTED & PACKING MATERIALS ***
16761791
24M15261
SERIAL LABEL
ENVELOPE(VL CLUB)
ACCESSORY BAG
SPACER F
SPACER R
M52
M52
24M16261
24MU4771
24MU4781
24MU4951
24MU5511
24MU5521
70800855
78037724
78038111
78038761
78047921
78048302
78411401
79646751
79646941
CARTON BOX
FILLER C,CARTON
PROTECTION BAG
POWER CORD J3 L3 BK,L(L)
VL CLUB LEAFLET
VL CLUB REGISTRATION CARD
QUICK REFERENCE (VT540J/440J)
WARRANTY ENVELOPE 100*220
WARRANTY CARD
USE'S MANUAL VT540J/VT440J
RD-366E
M52
M52
M52
M52
E10(M52)
M52
VT CABLE SET
*** VT CABLE SET ***
M52
M52
M52
M52
73499369
CABLE,RGB
ADAPTER D15P-MD15P
STRAP
70599172
24C05051
24C04534
PUSH RIVET
*** OPTION ***
REMOTE CONTROL KIT(J) (98999245)
73499328
73499329
73499353
79644981
79645901
CABLE SERIAL TO PS/2
CABLE SERIAL TO MAC
CABLE SIGNAL (DIN8P-D9P)
UNIVERSAL IR RECIEVER(J)
REM-T HAND UNIT RD-325\
10-26
VT540J
6. VT540J
SYMBOL
PART NO
DESCRIPTION
*** PWB ASSYS ***
E01
E02
E03
E04
935X7D01
935X7F01
935X7NA1
935X7NB1
LCEX PWB ASSY
MAIN PWB ASSY
I/O PWB ASSY
KEY PWB ASSY
*** ELECTRICAL PARTS & MISCELLANEOUS PARTS ***
E05
CN1
CN2
79646932
73895164
73895165
70ED2315
70ED2315
70ED2315
70ED2165
70ED2404
70ED2038
70ED2166
31700104
38102078
63099063
73W20077
73WLW001
64003036
64003037
64KA1118
64KA1122
64KA1140
65904524
65904524
65AB1116
65CF1506
65FK2102
66500003
66KA2008
POWER UNIT
CABLE,FFC 30P*38 P0.5 SU
CABLE,FFC 40P*38 P0.5 SU
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
CONNECTOR,FPC 30P
FPC CONNE FH12-30S-0.5SH
CONNECTOR,FFC 40P
CONNECTOR,FPC 40P
SCIROCCO FAN
THERMISTOR104JT-075-90271
SPEAKER 40*28MM 8H 1W
CN2P(SP)220S,1685-26
CN22P(MK)60W,1685-26
CRYSTAL RESONATOR
CRYSTAL RESONATOR
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
CRYSTALOSCILLATOR33.33333
DETECTOR SWITCH
DETECTOR SWITCH
SW,SLIDE
POBES
POGES
PORES
POST
POST
POSV
POSV
E06
E07
X1101
X1100
X3501
X3502
X3503
SW3313
SW4100
SW3301
SWITCH,TACT
RELAY
THERMOSTAT
DETECTOR SWITCH
RL3100
E08
SW3312
10-27
VT540J
*** APPEARANCE PARTS ***
S05
S06
S11
S09
S07
S01
S08
S03
S12
S13
12851741
910E2511
24N04721
910E2521
910E2531
910E306L
24N04781
910D3066
91613061
91614031
24N03651
24N04352
24N04691
24N04701
24N04731
24N04741
24N04751
24N04761
24N04771
91052031
91283076
91613076
12J00291
12J00301
12J00351
12J00361
12J00371
12J00381
12J00391
12J00401
12J00411
12J00421
12JS1351
12JS1361
12JS1371
12JS1381
12JS1391
12JS1431
12JS1441
12JS1451
OR 12JS1471
12JS1481
OR 12JS1491
12JS1501
12JS1511
12JS1521
SPECIAL SCREW(PL-HM2.5*6)
PL-CPIMS*2.5*6*15BF
SCREW(WASCHER 2.5*10)
PL-CPIMS*2.5*8*15BF
PL-CPIMS*2.5*10*15BF
PL-CPIMS*3*10*3GF
SPECIAL SCREW(PL-HM3*16)
PL-CPIMS*3*10*3KF
SCREW,#2CBTS*3*10*15BF
SCREW,#2CBITS*4*12*15BF
STUD(D-SUB,M2.6*3GF)
SPECIAL SCREW(M4)
STAD(M3*14,M/FM)
S02
S10
STAD(M3*17.5,M/FM)
SCREW(CBIPS2*6,PRECOAT)
SCREW(CFIPS3*6*15BF)
SPECIAL SCREW(HLSS4*6)
SCREW(PL-HHIMS2*5)
SCREW(CBIPS 3*10*15BF)
CFIMS2*6*15BF
SCREW,#2CPTS*3*12*3KF
SCREW,#2CBTS*3*12*3KF
CROSS PRISM(SKN)
S14
S04
CROSS PRISM(SKF)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
FIELD LENS(SK)
CONDENSER LENS 1(SK)
CONDENSER LENS 2(SK)
RELAY LENS 1(SK)
RELAY LENS 2(SK)
MIRROR 1(SK)
M48
FIELD LENS ASSY(SK)
CONDENSER LENS ASSY1(SK)
CONDENSER LENS ASSY2(SK)
RELAY LENS ASSY1(SK)
RELAY LENS ASSY2(SK)
ZOOM LENS(SK)
INTEGRATOR1(SKA)
INTEGRATOR2(SKA)
INTEGRATOR2(SKA)
POLARIZATION CONVERTER-S
POLARIZATION CONVERTER-S
MIRROR 0(SK)
MIRROR ASSY1(SK)
MIRROR 2(SK)
M05
M46
M44
M06
M07
M08
10-28
VT540J
*** APPEARANCE PARTS ***
M09
M10
12JS1531
12JS1541
12JS1551
12JS1561
12JS1571
12JS1581
12JS1601
12JS1711
12JS1721
25617801
24BS6621
24C02681
24C05911
24C05601
24D11431
24DT7492
24DT7675
24F29461
24F30581
24F31771
24F31781
24F31791
24F31801
24F31811
24F31821
24F31861
24F31871
24F31881
24F31901
24F31921
24F31931
24F31941
24F31951
24F31971
24F31981
24F31991
24F32011
24F32021
24F32031
24F32041
24F32051
24F32061
24F32071
24F32081
24F32091
24F32561
DICHROIC MIRROR 1(SK)
DICHROIC MIRROR 2(SK)
POLARIZER 1(SK)
POLARIZER 2(SK)
POLARIZER 3(SK)
REFLCTER LAMP(SK)
COVER GLASS(SK)
POLARIZER 3(SKK)
MIRROR ASSY1(SKT)
TAPE FORM
REMOCON CASE UNIT
CLIP(DS-9UL)
TILT RIVET
SPLIT PIN
TOP COVER(VT440J)
BOTTOM COVER ASSY
TOP COVER ASSY
TILT FOOT(R)
CUSHION FOOT(R)
HOLDER(CL1)
HOLDER(CL2)
HOLDER(FL)
HOLDER(RL1)
HOLDER(RL2)
HOLDER(M1)
INDICATOR
FILTER F
TILT FOOT F
HANDLE
CUSHION (FRONTFOOT)
LAMP COVER
FILTER CASE A
FILTER CASE B
SPEAKER HOLDER
FILTER S
M45
M20
M28
M22
M23
FILTER R
SEPARATE BASE(SK)
COVER OPT(SK)
DUCT CASE(SK)
INHAIL DUCT(SK)
COVER(INHAIL DUCT)
STOPPER(XDP)
LAMP BOX(F)
LAMP BOX(T)
LAMP BOX(B)
TILTINSERT
M13
10-29
VT540J
*** APPEARANCE PARTS ***
24F32601
WASHER(LAMP)
M24
M04
M21
M27
24FT6951
24FT7312
24FT7351
24FT7362
24FT7401
24FT7431
24FT7441
24FT7451
24FT7461
24FT7471
24G05271
24G05301
24H24411
24H35421
24H36621
24H36631
24H36641
24H36651
24H36661
24H36701
24H36741
24H36811
24H36821
24H36861
24H37091
24H37131
24H37191
24H37241
24H37321
24H37331
24H37341
24HS2581
24HS2591
24HS2601
24HS2621
24J15341
24J15451
24J15731
24J15751
24J15761
24J15811
24J15821
24J15831
24J15841
24J15851
CAP
LAMP COVER ASSY
FILTER ASSY A
FILTER ASSY B
TILT FOOT ASSY
SEPARATE BASE(SK) ASSY
DUCT CASE(SK)ASSY
INHAIL DUCT(SK)ASSY
COVER(INHAIL DUCT)ASSY
STOPPER (XDP)ASSY
PUSH BUTTON
PUSH BOTTON(TILT)
HALF NUT
GRIP
PLATE(FL)
PLATE(IT1)
PLATE(IT2)
PLATE(RL2)
PLATE(POL)
BRACKET(HANDLE)
TERMINAL BOARD
STAY R
SPRING S
SHAFT(HANDLE)
SPRING(TILT)
BARRIER (LAMP BOX)
BARRIER1(SEPARATE BASE)
BARRIER2(SEPARATE BASE)
BARRIER(LAMP COVER)
PLATE(I/O)
BARRIER(XDP)
BARRIER(LAMP BOX)ASSY
PLATE(FL)ASSY
PLATE(RL2)ASSY
BRACKET(I/O)ASSY
BARRIER(TOP)
DOUBLE FACE ADHESIVE TAPE
BARRIER(TILTFOOTR)
FILTER(COVER)A
FILTER(COVER)B
BARRIER
CUSHION (SEPARATE BASE)
CUSHION (DUCT CASE)
CUSHION (INHAIL DUCT)
CUSHION(INHAIL COVER)
M18
M25
M12
M11
M15
M29
M02
M43
M30
M16
M17
M26
10-30
VT540J
*** APPEARANCE PARTS ***
24J15861
24J15871
24J15961
24J15971
24J15981
24J15991
24J16021
24J16041
24K24401
24L11331
24L34401
24L41311
24L42201
24L43941
24L43991
24L44741
24L44981
24L45001
92203961
955X7161
955X7181
955X7191
955X7201
955X7211
955X7241
955X7251
955X7261
955X7131
CUSHION (FL)
CUSHION (RL2)
CUSHION2(INHAIL DUCT)
BARRIER(B/M)
SHEET A(SP)
M01
SHEET B(SP)
CUSHION(FILTER)
CUSHION(10*6.5*T13)
INLAY(I/O)
LABEL(8*28)
CAUTION LABEL(SERVICE)
CAUTION
CAUTION LABEL(EARTH)
NAME PLATE
LABEL POS
LABEL(VT LAMP)
LABEL(LENS)
LABEL(3.5*20)
TAPE SCOTCH SUPER
LAMP BOX SASSY
R POL SASSY
G POL SASSY
B POL SASSY
FL SASSY
IT1 SASSY
IT2 SASSY
RL2 SASSY
E09
M36
M37
M38
M40
M41
M42
M39
M35
OPT BASE SASSY
10-31
VT540J
*** PRINTED & PACKING MATERIALS ***
16761791
24M15261
SERIAL LABEL
ENVELOPE(VL CLUB)
ACCESSORY BAG
SPACER F
SPACER R
M52
M52
24M16261
24MU4771
24MU4781
24MU4921
24MU5511
24MU5521
70800855
78037724
78038111
78038761
78047921
78048302
78411401
79646751
79646941
CARTON BOX
FILLER C,CARTON
PROTECTION BAG
POWER CORD J3 L3 BK,L(L)
VL CLUB LEAFLET
VL CLUB REGISTRATION CARD
QUICK REFERENCE (VT540J/440J)
WARRANTY ENVELOPE 100*220
WARRANTY CARD
USE'S MANUAL VT540J/VT440J
RD-366E
M52
M52
M52
M52
E10(M52)
M52
VT CABLE SET
*** VT CABLE SET ***
M52
M52
M52
M52
73499369
CABLE,RGB
ADAPTER D15P-MD15P
STRAP
70599172
24C05051
24C04534
PUSH RIVET
*** OPTION ***
REMOTE CONTROL KIT(J) (98999245)
73499328
73499329
73499353
79644981
79645901
CABLE SERIAL TO PS/2
CABLE SERIAL TO MAC
CABLE SIGNAL (DIN8P-D9P)
UNIVERSAL IR RECIEVER(J)
REM-T HAND UNIT RD-325
10-32
VIDEO/SYNC BLOCK
PRINTED IN JAPAN
0002MI0030
01150034 (VT440)
01150035 (VT440G)
01151012 (VT440J)
01150031 (VT540)
01150032 (VT540G)
01151011 (VT540J)
PRINTED IN JAPAN
0005MI0030
01150034 (VT440)
01150035 (VT440G)
01151012 (VT440J)
01150031 (VT540)
01150032 (VT540G)
01151011 (VT540J)
|