NEC MULTISYNC EA245WMI 2 User Manual

Desktop Monitor  
MultiSync EA245WMi-2  
User’s Manual  
MODEL: EA245WMi, EA245WMi-BK  
Please find your model name in the label on the backside of monitor.  
WARNING  
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT  
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE  
PRONGS CAN BE FULLY INSERTED.  
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
CAUTION  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED  
FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT  
THE POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER  
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause  
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.  
This symbol alerts the user that important literature concerning the operation and maintenance of this unit  
has been included. Therefore, it should be read carefully in order to avoid any problems.  
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not  
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the  
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.  
This equipment is designed to be used in the condition of the power cord connected to earth. If the power cord is not connected  
to the earth, it may cause electric shock. Please make sure the power cord is earthed properly.  
Plug Type  
North America  
European Continental  
U.K.  
Chinese  
Japanese  
Plug Shape  
Region  
Voltage  
U.S.A./Canada  
120*  
EU (except U.K.)  
230  
U.K.  
230  
China  
220  
Japan  
100  
*When operating the monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply  
voltage of the AC power outlet being used.  
NOTE:  
This product can only be serviced in the country where it was purchased.  
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.  
ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France,  
Germany, Italy, Norway, Spain, Sweden, U.K.  
All other brands and product names are trademarks or registered trademarks of their respective owners.  
DisplayPort and DisplayPort Compliance Logo are trademarks owned by Video Electronics Standards  
Association in the United States and other countries.  
HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of  
video data sent over a digital signal. If you are unable to view material via the digital signal input, this does  
not necessarily mean the display is not functioning properly. With the implementation of HDCP, there may be cases in which  
certain content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP community (Digital  
Content Protection, LLC).  
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks  
or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.  
The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment.  
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.  
English-1  
Registration Information  
FCC Information  
1.  
Use the attached specified cables with this monitor so as not to interfere with radio and television reception.  
(1)  
The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,  
and meet the following condition.  
Power supply cord  
Plug shape  
Non shield type, 3-conductor  
U.S.A  
(2)  
Please use the supplied shielded video signal cable.  
Use of other cables and adapters may cause interference with radio and television reception.  
2.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used  
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult your dealer or an experienced radio/TV technician for help.  
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.  
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify  
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,  
Washington, D.C., 20402, Stock No. 004-000-00345-4.  
Declaration of Conformity  
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not  
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  
undesired operation.  
U.S. Responsible Party: NEC Display Solutions of America, Inc.  
Address:  
500 Park Boulevard, Suite 1100  
Itasca, Illinois 60143  
(630) 467-3000  
Tel. No.:  
Type of Product:  
Display Monitor  
Equipment Classification: Class B Peripheral  
Model: MultiSync EA245WMi-2 (EA245WMi, EA245WMi-BK)  
We hereby declare that the equipment specified above conforms  
to the technical standards as specified in the FCC Rules.  
To see a list of our TCO certified monitors and their TCO Certification (in English only), visit our website at  
English-2  
Recommended use  
Safety Precautions and Maintenance  
FOR OPTIMUM PERFORMANCE, PLEASE NOTE  
THE FOLLOWING WHEN SETTING UP AND  
USING THE LCD COLOR MONITOR:  
DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose  
you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.  
Do not spill any liquids into the cabinet or use your monitor near water.  
Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful or  
fatal or may cause electric shock, fire or equipment failure.  
Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.  
Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to  
the monitor.  
The power supply cord you use must have been approved by and comply with the safety standards of your country.  
(Type H05VV-F 3G 0.75 mm2 should be used in Europe).  
In UK, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor.  
Do not place any objects onto the monitor and do not use the monitor outdoors.  
Do not bend power cord.  
Do not use monitor in high temperatured, humid, dusty, or oily areas.  
Do not cover vent on monitor.  
Vibration can damage the backlight. Do not install where the monitor will be exposed to continual vibration.  
If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.  
To prevent damage to the LCD monitor caused by tipping over due to earthquakes or other shocks, make sure to install the  
monitor in a stable location and take measures to prevent falling.  
Immediately turn off the power, unplug your monitor from the wall outlet and move to a safe location then refer servicing to  
qualified service personnel under the following conditions. If the monitor is used in this condition, the monitor may cause fall, fire  
and electric shock:  
If the monitor stand has been cracked or peeled.  
If the monitor has been wobbled.  
If the monitor has an unusual odor.  
When the power supply cord or plug is damaged.  
If liquid has been spilled, or objects have fallen into the monitor.  
If the monitor has been exposed to rain or water.  
If the monitor has been dropped or the cabinet damaged.  
If the monitor does not operate normally by following operating instructions.  
Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated  
openings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor.  
The power cable connector is the primary means of detaching the system from the power supply.  
The monitor should be installed close to a power outlet which is easily accessible.  
CAUTION  
Handle with care when transporting. Save packaging for transporting.  
Do not touch LCD panel surface while transporting, mounting and setting.  
Applying pressure on the LCD panel can cause serious damage.  
Image Persistence: Image persistence is when a residual or “ghost” image of a previous image remains visible on the screen.  
Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period  
of time should be avoided.  
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image  
was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.  
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular  
intervals whenever the screen is idle or turning off the monitor when not in use.  
English-3  
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN  
REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE  
FOLLOWING WHEN YOU POSITION THE MONITOR:  
For optimum performance, allow 20 minutes for the display to warm up.  
Adjust the monitor height so that the top of the screen is at or slightly below eye level.  
Your eyes should look slightly downward when viewing the middle of the screen.  
Position your monitor no closer than 40 cm (15.75 inches) and no further away than  
70 cm (27.56 inches) from your eyes. The optimal distance is 50 cm (19.69 inches).  
Rest your eyes periodically for 5 to 10 minutes for every 1 hour by focusing on an object  
at least 20 feet away.  
Position the monitor at a 90° angle to windows and other light sources to minimize glare  
and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your screen.  
If reflected light makes it hard for you to see your screen, use an anti-glare filter.  
Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any  
cleaning solution or glass cleaner!  
Adjust the monitor’s brightness and contrast controls to enhance readability.  
Use a document holder placed close to the screen.  
Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize  
turning your head while you are typing.  
Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image effects).  
Blink often. Eye exercise helps to reduce eye strain. Please contact your ophthalmologist. Get regular eye checkups.  
Ergonomics  
To realize the maximum ergonomics benefits, we recommend the following:  
To avoid eye fatigue, adjust the brightness to a moderate setting. Place a sheet of white paper next to the LCD screen for  
luminance reference.  
Do not position the Contrast control to its maximum setting.  
Use the preset Size and Position controls with standard signals.  
Use the preset Color Setting.  
Use non-interlaced signals with a vertical refresh rate of 60 Hz.  
Do not use primary color blue on a dark background, as it is difficult to see and may produce eye fatigue due to insufficient  
contrast.  
Suitable for entertainment purposes at controlled luminous environments, to avoid disturbing reflections from the screen.  
Cleaning the LCD Panel  
When the LCD is dusty, please gently wipe with a soft cloth.  
Please do not rub the LCD panel with hard or coarse material.  
Please do not apply pressure to the LCD surface.  
Please do not use OA cleaner as it will cause deterioration or discoloration on the LCD surface.  
Cleaning the Cabinet  
Unplug the power supply  
Gently wipe the cabinet with a soft cloth  
To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and follow with a dry cloth.  
NOTE:  
Many plastics are used on the surface of the cabinet. DO NOT clean with benzene, thinner, alkaline detergent,  
alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Do not touch rubber or  
vinyl to the cabinet for a long time. These types of fluids and fabrics can cause the paint to deteriorate, crack or peel.  
For more detailed information on setting up a healthy work environment, write to the American National Standard for Human  
Factors Engineering of Computer Workstations - ANSI/HFES 100-2007 - The Human Factors Society, Inc. P.O. Box 1369, Santa  
Monica, California 90406.  
English-4  
Quick Start  
For contents, please refer to the contents sheet.  
To attach the Base to the LCD stand:  
1. Place monitor face down on a non-abrasive surface (Figure 1).  
2. Please rotate the stand 90 degrees as shown in Figure 1.  
NOTE:  
Handle with care when pulling the stand.  
3. Attach the base to the stand and lock screw at the base’s bottom  
(Figure 2).  
NOTE:  
To connect the LCD monitor to your system, follow these instructions:  
NOTE: Make sure to read “Recommended Use” (page 3) before installation.  
Reverse this procedure if you need to re-pack the monitor.  
Figure 1  
Screw  
The accessories included will depend on the where the LCD monitor is to be shipped.  
Figure 2  
1. Turn off the power of your computer.  
2. For a PC with DisplayPort output: Connect the DisplayPort cable to the connector of the display card in your system  
(Figure A.1).  
For a PC with HDMI output: Connect the HDMI cable to the connector of the display card in your system (Figure A.2).  
For a PC with Analog output: Connect a 15-pin mini D-SUB signal cable to the connector of the display card in your  
system (Figure A.3).  
For a MAC with Thunderbolt or Mini DisplayPort output: Connect a Mini DisplayPort to DisplayPort cable to a video  
connector in your system.  
An alternative is to use an approved Mini DisplayPort to DisplayPort cable to connect the computer to the display  
(Figure A.4).  
For a PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system  
(Figure A.5). Tighten all screws.  
DisplayPort cable  
HDMI cable  
15-pin mini D-SUB signal cable  
Figure A.1  
Figure A.2  
Figure A.3  
Mini DisplayPort to DisplayPort cable  
DVI cable  
Figure A.4  
Figure A.5  
NOTE:  
1. When removing the DisplayPort cable, hold down the top button to release the lock.  
2. Please use a High Speed HDMI cable with HDMI logo.  
3. Please use a DisplayPort Certified DisplayPort cable.  
English-5  
3. Place hands on each side of the monitor to tilt the LCD panel 35-degree angle and lift up to the highest position.  
4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector  
to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the  
computer (Figure C.1a). If using the cord from a USB device, plug into the downstream port of the monitor.  
NOTE:  
Incorrect cable connections may cause abnormal operation, damage display quality/components of LCD module  
and/or shorten the module’s life.  
NOTE:  
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.  
35° Tilt  
A Type  
A Type  
Headphone  
B Type  
USB Downstream (USB Type-A)  
Highest Stand  
USB Upstrream (UUSB Typpe-B)  
Position  
B Type  
Figure C.1a  
DisplayPort OUT*1  
DisplayPort IN*1  
HDMI  
ControlSync IN*2  
ControlSync OUT*2  
Audio Input  
DVI  
D-SUB  
Power cord  
Figure C.1  
Figure C.2  
*1: See page 10.  
*2: See page 11.  
NOTE:  
Adjustment of the volume control as well as the equalizer to other settings than the center position may increase the  
ear-/headphones output voltage and therefore the sound pressure level.  
5. Place the cable holder onto the stand (Figure C.2).  
Place the cables in the cable holder firmly and evenly (Figure C.3 and Figure C.4).  
6. Please check that you can still rotate, raise and lower the monitor screen after you have installed the cables.  
HDMI Cable  
DisplayPort  
Cables  
Security Slot  
Power Cord  
DVI Cable  
Mini D-SUB  
15 pin Cable  
ControlSync  
Cables  
HDMI Cable  
DisplayPort Cables  
Mini D-SUB 15 pin Cable  
Power Cord  
DVI Cable  
ControlSync Cables  
Audio Cable*3  
Audio Cable*3  
Figure C.3  
Figure C.4  
*3: ø 3.5 stereo mini plug.  
English-6  
7. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet.  
NOTE: Please refer to Caution section of this manual for proper selection of AC power cord.  
8. Turn on the computer and the monitor by touching the power key on the front bezel (Figure E.1).  
9. No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup. For further adjustments, use  
the following OSD controls:  
• AUTO CONTRAST (Analog input only)  
• AUTO ADJUST (Analog input only)  
Refer to the Controls section of this User’s Manual for a full description of these OSD controls.  
NOTE:  
If you have any problems, please refer to the Troubleshooting section of this User’s Manual.  
Power key  
Figure E.1  
Raise and Lower Monitor Screen  
The monitor may be raised or lowered in either portrait or landscape mode.  
To raise or lower screen, place a hand on each side of the monitor and lift or lower to the desired height (Figure RL.1).  
NOTE:  
Handle with care when raising or lowering the monitor screen.  
Figure RL.1  
Screen Rotation  
Before rotating, disconnect power cord and all cables, then the screen must be raised to the highest level and tilt to avoid  
knocking the screen on the desk or pinching your fingers.  
To raise the screen, place a hand on each side of the monitor and lift up to the highest position (Figure RL.1).  
To rotate screen, place a hand on each side of the monitor screen and turn it from landscape to portrait (Figure R.1).  
Figure R.1  
English-7  
Tilt and Swivel  
Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1).  
Figure TS.1  
NOTE:  
Handle with care when tilting the monitor screen.  
Flexible Arm Installation  
This LCD monitor is designed for use with a flexible arm.  
To prepare the monitor for alternate mounting purposes:  
Follow the instructions provided by the manufacturer of the display mount.  
To meet the safety requirements, the mounting stand must be able to support the weight of the monitor and be UL-certified.  
* Contact your dealer for more information.  
Remove Monitor Stand for Mounting  
To prepare the monitor for alternate mounting purposes:  
1. Disconnect all cables.  
2. Place hands on each side of the monitor and lift up to the highest position.  
3. Place monitor face down on a non-abrasive surface (Figure S.1).  
4. Place one hand around the base and one hand on the Quick Release Lever.  
Push and hold the Quick Release Lever in the direction indicated by the arrows (Figure S.1).  
5. Lift up the stand to unhook it from the monitor (Figure S.1).  
The monitor can now be mounted using an alternate method.  
Reverse the process to reattach stand.  
NOTE:  
Handle with care when removing monitor stand.  
Figure S.1  
English-8  
Mount Flexible arm  
This LCD monitor is designed for use with a flexible arm.  
1. Follow the instructions on how to Remove Monitor Stand for Mounting.  
2. Using the specified 4 screws, attach the arm to the monitor (Figure F.1).  
Spring washer  
12 mm  
Flat washer  
Thickness of Bracket (Arm)  
2.0~3.2 mm  
100 mm  
100 mm  
Weight of LCD assembly: 4.2 kg  
Figure F.1  
Caution: Use ONLY 4 M4 sized screws when mounting to avoid damage to the monitor and stand.  
To fulfill the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability  
under consideration of the weight of the monitor. The LCD monitor should only be used with an approved arm  
(e.g. TUEV GS mark).  
NOTE:  
Tighten all screws (recommended Fasten Force: 98 - 137N•cm).  
English-9  
ControlSync  
1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT.  
2. Follow the steps of DATA COPY. When the setting of the master monitor is adjusted, it will be copied and sent to the  
connected sub monitor(s) automatically.  
3. Up to 24 sub monitors can be daisy-chained via ControlSync.  
NOTE:  
Connect the master monitor via ControlSync OUT connector.  
The ControlSync icon will appear on the upper left of the OSD menu in the sub monitor.  
Do not connect IN-IN or OUT-OUT.  
ControlSync icon  
Do not make “loop” connection.  
Once the monitors are connected, turn the master monitor’s power key off and on  
to check if ControlSync operates correctly.  
If connecting monitors with DisplayPort cables, please make sure the monitor which is connected to a computer is the  
master monitor.  
Master Monitor  
Sub Monitor 1  
Sub Monitor 2  
IN (Gray)  
OUT (Black)  
IN OUT  
IN OUT  
Up to 24 sub monitors  
Next monitor  
(Black)  
(Gray)  
(Black)  
(Gray)  
ControlSync cable  
ControlSync cable  
The following settings can be controlled by ControlSync:  
ECO TOOLS  
BRIGHTNESS*  
CONTRAST  
ECO MODE  
AUTO BRIGHTNESS  
BLACK LEVEL  
Yes  
No  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
No  
No  
No  
No  
No  
No  
No  
No  
TOOLS  
VOLUME  
SOUND INPUT  
VIDEO DETECT  
Yes  
No  
No  
No  
No  
Yes  
No  
Yes  
Yes  
No  
DP OUT MULTISTREAM  
RESPONSE IMPROVE  
OFF TIMER  
POWER SAVE TIMER  
LED BRIGHTNESS  
DDC/CI  
USB POWER  
180° ROTATE  
FACTORY PRESET  
LANGUAGE  
OSD TURN OFF  
OFF MODE SETTING  
OFF MODE SENSOR SETTING  
OFF MODE START TIME  
HUMAN SENSING  
HUMAN SENSOR SETTING  
HUMAN SENSOR START TIME  
DV MODE  
No  
No  
SCREEN  
AUTO ADJUST  
AUTO CONTRAST  
LEFT/RIGHT  
MENU TOOLS  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
No  
No  
No  
No  
OSD LOCK OUT  
DOWN/UP  
H.SIZE  
FINE  
HOT KEY  
SIGNAL INFORMATION  
SENSOR INFORMATION  
KEY GUIDE  
INPUT RESOLUTION  
H.RESOLUTION  
V.RESOLUTION  
VIDEO LEVEL  
OVER SCAN  
EXPANSION  
UNIFORMITY  
Color Control System  
R, G, B, color gain  
DATA COPY  
CUSTOMIZE SETTING  
CARBON SAVINGS  
CARBON USAGE  
COST SAVINGS  
No  
No  
Yes  
No  
Yes  
No  
ECO INFORMATION  
CARBON CONVERT SETTING  
CURRENCY SETTING  
CURRENCY CONVERT SETTING  
Yes  
Yes  
Yes  
COLOR  
Other settings:  
Power Control (DC switch)  
Ambient Light Sensor  
Human Sensor Result  
Audio Mute  
NOTE:  
Only the master monitor’s human sensor and ambient light sensor are active. Please do not cover these sensors.  
Turn the monitor’s power off before connecting/disconnecting the ControlSync cable.  
Do not use the ControlSync connectors for any purpose other than specified.  
* This value is not a directly adjusted output value. This is adjusted relatively.  
English-10  
Multiple monitors connection using DisplayPort  
You can connect multiple monitors by using DisplayPort daisy-chain connection.  
For using as multiple monitors in MST (multi-stream transport) mode, setting should be DP OUT MULTISTREAM “AUTO” at  
each connected monitor. Please change the monitor setting which is connected to a computer last in the connected monitors.  
If monitors have no image, turn off the monitor who is connected to a computer then turn it on.  
Some DisplayPort configuration may be required. Please refer below and set as required.  
OSD (See page 17)  
Factory setting.  
DP OUT MULTISTREAM “CLONE” DisplayPort 1.1a setting with:  
– SST (single-stream transport).  
DisplayPort 1.2 setting with:  
DP OUT MULTISTREAM “AUTO”  
– SST (single-stream transport) and MST (multi-stream transport).  
Depending on the setting of computer operation system, image does not extend.  
Please check your computer setting.  
NOTE:  
Monitors should be connected by the included DisplayPort cable.  
Using the same display model is strongly recommended for connecting multiple monitors.  
Please contact your display card supplier for detailed information.  
BIT RATE  
Maximum number of connectable monitors  
4 units (HDCP contents: 4 units)  
HBR2 (Default setting)  
HBR  
MST (multi-stream transport)  
2 units (HDCP contents: 2 units)  
NOTE:  
The number of monitors daisy-chained depends on display card and various factors.  
DisplayPort IN  
DisplayPort OUT  
DisplayPort  
DisplayPort IN/OUT  
DisplayPort IN/OUT  
DisplayPort cable  
DisplayPort cable  
DisplayPort cable  
NOTE:  
When the monitor has no image, follow the troubleshooting step Recovering from no image and select  
DP VER “1.1” (see page 12). Then set from the first step.  
When this MST function is selected, the power management function according to the ErP directive doesn’t work.  
English-11  
Recovering from no image  
If monitors have no image after setting DP OUT MULTISTREAM, please set as follows:  
1. Turn off the computer.  
2. Touch the “MENU” key to show the No Signal OSD menu.  
3. Touch the “ ” key to show VIDEO INPUT menu.  
4. Touch “ ” or “ ” to show to set the DisplayPort switch menu.  
5. Select DP VER “1.1” to switch the DisplayPort setting.  
6. Touch MENU to close the OSD menu.  
7. Turn on the computer.  
NOTE:  
MST (multi-stream transport) and SST (single-stream transport) requires the corresponding display card.  
Check to make sure that the display card supports MST (multi-stream transport).  
Contact your supplier for detailed information.  
NOTE:  
Monitors should be connected by the included DisplayPort cable.  
English-12  
Controls  
OSD (On-Screen Display) control keys on the front of the monitor function  
are as follows:  
To access OSD menu, touch any of the control keys.  
To change signal input, touch the SELECT key.  
NOTE:  
Exit OSD in order to change signal input.  
1 Ambient Light Sensor  
Human Sensor  
Detects the level of ambient lighting and the presence of a user, allowing the monitor to  
make adjustments to various settings resulting in a more comfortable viewing experience.  
Do not cover this sensor.  
2 INPUT/SELECT  
Enters the OSD menu. Enters OSD sub menus.  
Changes the input source when not in the OSD menu. You can directly change to L/B  
(LOW BLUE LIGHT) mode by touching the INPUT key for 3 seconds or more.  
3 MENU/EXIT  
4 LEFT/RIGHT  
5 UP/DOWN  
Accesses OSD menu. Exits the OSD sub menu. Exits OSD menu.  
Navigates to the left or right through the OSD menu.  
Navigates up or down through the OSD menu.  
You can adjust the BRIGHTNESS directly by touching UP while the OSD menu is off.*1  
You can adjust the VOLUME directly by touching DOWN while the OSD menu is off.*1  
6 ECO/RESET  
Resets the OSD controls back to factory settings. Switches among ECO MODE settings.  
Activates the Auto Adjust function if held for 3 seconds while the OSD menu is off  
(analog input only)*1.  
7 Power  
Turns the monitor on and off.  
8 Power LED  
Indicates that the power is on or off.  
*1 When Hot Key function is OFF, this function is disabled.  
ECO TOOLS  
BRIGHTNESS  
Adjusts the overall image and background screen brightness.  
If ECO MODE is set to 1 or 2, a bar for CARBON FOOTPRINT will appear.  
CONTRAST  
Adjusts the overall image and background screen brightness by input signal level.  
NOTE: CONTRAST and DV MODE can be adjusted when other than L/B is selected for COLOR CONTROL.  
English-13  
ECO MODE  
Decreases the amount of power consumption by reducing the brightness level.  
OFF: No function.  
1: Sets brightness variable range from 0% to 60%.  
This setting can adjust brightness to a range in which power is reduced by 20% compared to the maximum brightness  
setting.  
2: Sets brightness variable range from 0% to 30%.  
This setting can adjust brightness to a range in which power is reduced by 35% compared to the maximum brightness  
setting.  
When this function is set to ON, a CARBON FOOTPRINT bar will appear alongside the brightness adjustment bar.  
NOTE: This function is disabled when DV MODE is set to DYNAMIC.  
This function is disabled when Color Control System is set to DICOM SIM.  
To enter the ECO MODE, touch ECO.  
If you touch ECO, the setting changes [1]  
[2]  
[OFF]  
[1].  
AUTO BRIGHTNESS  
OFF: No function.  
ON (AMBIENT LIGHT): Automatically adjusts the brightness to the optimal setting by detecting the brightness level of  
the environment*1.  
*1: Please refer to page 26 for full “Auto Brightness” information.  
NOTE: This function is disabled when DV MODE is set to DYNAMIC.  
This function is disabled when Color Control System is set to DICOM SIM.  
BLACK LEVEL  
Adjusts the black level.  
OFF MODE SETTING  
The Intelligent Power Manager allows the monitor to enter into power saving mode after a period of inactivity.  
The OFF MODE has two settings:  
OFF: Monitor enters into power saving mode automatically when the input signal is lost.  
ON: Monitor enters into power saving mode automatically when the amount of surrounding light goes below the level  
determined by you. The level can be adjusted in OFF MODE sensor setting.  
When in power saving mode, the LED on the front of the monitor becomes dark blue. When in power saving mode,  
touch any of the front keys, except for POWER and INPUT, to return to normal.  
When the amount of surrounding light returns to normal levels, the monitor will automatically return to normal mode.  
SENSOR SETTING (OFF MODE SETTING)  
Adjusts threshold level of ambient light sensor for detected dark condition and shows current sensor measurement  
result.  
START TIME (OFF MODE SETTING)  
Adjusts wait time to enter into to a lower power consumption level when ambient light sensor detects dark condition.  
HUMAN SENSING  
The sensor detects the movement of a person by using the HUMAN SENSING function. The HUMAN SENSING has  
three settings:  
OFF: No human sensing.  
1 (LIGHT): After it is detected that there is no person after a period of time, the monitor shifts to low brightness mode  
automatically to reduce the power consumption. When a person comes near the monitor again, the monitor will  
automatically return to normal mode. START TIME adjusts the wait time to react.  
2 (DEEP): After it is detected that there is no person, the monitor shifts to power saving mode automatically to reduce  
the power consumption. When a person comes near the monitor again, it resumes from the power saving mode.  
NOTE: Detects a person within about 1.5 m from the monitor.  
English-14  
SENSOR SETTING (HUMAN SENSING)  
Adjusts the threshold level of human sensing.  
When the human icon is located on the right side of the white color bar or vermilion color wave, a person is not  
detected.  
NOTE: Once the OSD has been closed, Human sensor starts to work.  
START TIME (HUMAN SENSING)  
Adjusts the wait time of entering to low brightness mode or power saving mode when Human Sensor detects no  
person.  
DV MODE  
Dynamic Visual Mode allows you to select from the following settings:  
STANDARD: Standard setting.  
TEXT: Setting that makes letters and lines crisp; best suited for basic word processing and spreadsheets.  
MOVIE: Setting that boosts dark tones; best suited for movies.  
GAMING: Setting that boosts whole tones; best suited for games that use vivid and colorful images.  
PHOTO: Setting that optimizes contrast; best suited for still images.  
DYNAMIC: Setting that adjusts the brightness by detecting the screen’s black areas and optimizes it.  
NOTE: This function is disabled when Color Control System is set to L/B, PROGRAMMABLE or DICOM SIM.  
STANDARD is used for TCO Certificate compliance.  
SCREEN  
AUTO ADJUST (Analog input only)  
Automatically adjusts the image position, H. Size and Fine settings.  
AUTO CONTRAST (Analog input only)  
Adjusts the image displayed for non-standard video inputs.  
LEFT / RIGHT  
Controls horizontal image position within the display area of the LCD.  
DOWN / UP  
Controls vertical image position within the display area of the LCD.  
H.SIZE (Analog input only)  
Adjusts the horizontal size by increasing or decreasing this setting.  
If the “AUTO Adjust” function does not give you a satisfactory picture setting, a further tuning can be performed by  
using the “H.SIZE” function (dot clock). For this a Moiré test pattern could be used. This function may alter the width  
of the picture. Use LEFT/RIGHT key to center the image on the screen. If the H.SIZE is wrongly calibrated, the result  
would look like the left drawing. The image should be homogeneous.  
When H.SIZE value is  
wrong.  
When H.SIZE value is  
improved.  
When H.SIZE value is  
correct.  
English-15  
FINE (Analog input only)  
Improves focus, clarity and image stability by increasing or decreasing this setting.  
If the “Auto Adjust” function and the “H.SIZE” function do not give you a satisfactory picture setting, a fine tuning can be  
performed by using the “FINE” function.  
For this a Moiré test pattern could be used. If the Fine value is wrongly calibrated, the result would look like the left  
drawing. The image should be homogeneous.  
When FINE value is  
wrong.  
When FINE value is  
correct.  
INPUT RESOLUTION (Analog input only)  
Selects one of the following pair of resolutions as the input signal priority:  
1360 x 768 or 1280 x 768 or 1024 x 768 (vertical resolution 768),  
1600 x 900 or 1280 x 960 (horizontal frequency 60kHz),  
1680 x 1050 or 1400 x 1050 (vertical resolution 1050).  
H.RESOLUTION (Digital input only)  
Adjusts the horizontal size by increasing or decreasing the resolution.  
Touch the “RIGHT” key to reduce the width of the image on the screen.  
Touch the “LEFT” key to expand the width of the image on the screen.  
NOTE: When this function may not work, reduce the H.RESOLUTION level.  
V.RESOLUTION (Digital input only)  
Adjusts the vertical size by increasing or decreasing the resolution.  
Touch the “RIGHT” key to reduce the height of the image on the screen.  
Touch the “LEFT” key to expand the height of the image on the screen.  
NOTE: When this function may not work, reduce the V.RESOLUTION level.  
VIDEO LEVEL (HDMI input only)  
NORMAL: For computer setting. Displays all input signals of 0-255 steps.  
EXPAND: For audio-visual equipment setting. Expands input signals of 16-235 steps to 0-255 steps.  
OVER SCAN (HDMI input only)  
Some video formats may require different scanning modes in order to best display the image.  
ON: Image size is larger than what can be displayed. The image edge will appear cropped. Approximately 95% of the  
image will be shown on the screen.  
OFF: Image size stays within the display area. The whole image is displayed on the screen.  
EXPANSION  
Sets the Zoom method.  
FULL: The image is expanded to full screen regardless of the resolution.  
ASPECT: The image is expanded without changing the aspect ratio.  
OFF: The image is not expanded.  
UNIFORMITY  
This function electronically compensates for the slight variations in the white uniformity level as well as for deviations  
in color that may occur throughout the display area of the screen. These variations are characteristic of LCD panel  
technology. This function improves the color and evens out the luminance uniformity of the display.  
NOTE: Using the UNIFORMITY feature does reduce the overall peak luminance of the display. If greater luminance is  
desired over the uniform performance of the display, then UNIFORMITY should be turned off. “ON” produces  
a better effect, but may also reduce contrast ratio.  
English-16  
Color  
Color Control System: Color presets are available for adjusting color settings. (sRGB and NATIVE color presets are  
standard and cannot be changed).  
1, 2, 3, sRGB, 5: Increases or decreases Red, Green or Blue color depending upon which is selected. The change  
in color will appear on screen and the direction (increase or decrease) will be shown by the bars. sRGB mode  
dramatically improves the color fidelity in the desktop environment by a single standard RGB color space. With this  
color-supported environment, the operator could easily and confidently communicate color without further color  
management overhead in most common situations.  
NATIVE: Original color presented by the LCD panel that is unadjustable.  
L/B (LOW BLUE LIGHT): Reduces blue light emitted from monitor.  
NOTE: You can directly change to L/B (LOW BLUE LIGHT) mode by touching the SELECT key for 3 seconds or  
more. For changing to other settings from L/B mode, touch the INPUT key to show OSD menu and enter  
COLOR control.  
When L/B is selected in COLOR control, CONTRAST and DV MODE are disabled.  
DICOM SIM.: The white point color temperature and the gamma curve are set to a DICOM simulation.  
PROGRAMMABLE: The gamma curve is adjustable through application software.  
NOTE: When MOVIE, GAMING, or PHOTO is selected as the DV MODE, NATIVE is selected automatically and  
cannot be changed.  
Tools  
VOLUME  
Controls the volume of the speakers or headphones.  
To mute the speaker output, touch the “ECO/RESET” key.  
SOUND INPUT (HDMI, DisplayPort inputs only)  
This function selects Audio Input, HDMI or DisplayPort.  
VIDEO DETECT  
Selects the method of video detection when more than one video inputs are connected.  
FIRST: When current video input signal is not present, then the monitor searches for a video signal from the other  
video input ports. If the video signal is present in another port, then the monitor switches the video source input port  
to the new found video source automatically. The monitor will not look for other video signals while the current video  
source is present.  
NONE: The monitor will not search the other video input port unless it is turned on.  
DP OUT MULTISTREAM  
Selects DisplayPort mode.  
CLONE: Sets SST (single-stream transport). Default is “CLONE”.  
If multiple monitors are set to MST (multi-stream transport), same image is displayed at each monitor.  
AUTO: Displays in SST (single-stream transport) or MST (multi-stream transport) mode. “AUTO” should be selected  
when using MST (multi-stream transport).*  
If multiple monitors are set to SST (single-stream transport), individual image is displayed at each monitor.  
NOTE: When the monitor has no image, refer to Multiple monitors connection using DisplayPort (see page 11).  
*: MST (multi-stream transport) and SST (single-stream transport) require the corresponding display card. Contact your dealer for limitations of this function.  
RESPONSE IMPROVE  
Turns the Response Improve function on or off. Response Improve may reduce blurring that occurs in some moving  
images.  
OFF TIMER  
Monitor will automatically power down when you have selected a pre-determined amount of time.  
Before powering off, a message will appear on the screen asking if you want to delay the turn off time by 60 minutes.  
Touch any OSD key to delay the power-down time.  
English-17  
POWER SAVE TIMER  
POWER SAVE TIMER allows the monitor to turn off automatically after continuing power saving mode for 2 hours.  
LED BRIGHTNESS  
You can adjust the blue LED brightness.  
DDC/CI  
This function allows the DDC/CI function ON or OFF.  
USB POWER  
Selects a power relation of USB.  
AUTO: Power is supplied to USB downstream port depending on related power condition.  
ON: Power is always supplied to USB downstream port even when in power save mode or power OFF.  
NOTE: Power consumption depends on connected USB even when a monitor’s power is off.  
180° ROTATE  
Select to display the image for 0° or 180°.  
FACTORY PRESET  
Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings except Language and  
OSD Lock Out. Individual settings can be reset by touching the “ECO/RESET” key.  
MENU Tools  
LANGUAGE  
Selects the language used by the OSD.  
OSD TURN OFF  
The OSD menu will stay on as long as it is in use. You can select how long the monitor waits after the last key touch to  
shut off the OSD menu. The preset choices are 10-120 seconds by 5-second increments.  
OSD LOCK OUT  
This control completely locks out the access to all OSD control functions except for Brightness, Contrast and Volume.  
To activate the OSD Lock Out function, enter the OSD menu, select OSD LOCK OUT, then touch “SELECT” and  
RIGHT simultaneously. To deactivate, touch “SELECT” and LEFT simultaneously.  
HOT KEY  
When this function is activated BRIGHTNESS and VOLUME can be adjusted without entering the OSD menu by using  
the front keys.  
ON: The “ECO” touch key on the bezel is enabled and can toggle among ECO settings.  
The Up/Down key adjusts the VOLUME and the BRIGHTNESS level.  
OFF: The HOT KEY function for “ECO” and “Up/Down” functions are disabled.  
SIGNAL INFORMATION  
If you select “ON”, monitor displays “VIDEO INPUT MENU” after changing the input.  
If you select “OFF”, monitor doesn’t display “VIDEO INPUT MENU” after changing the input.  
SENSOR INFORMATION  
If you select “ON”, monitor displays “HUMAN SENSOR ON” message. If you select “OFF”, monitor doesn’t display  
“HUMAN SENSOR ON” message.  
KEY GUIDE  
If you select “ON”, the Key Guide appears on screen when the OSD menu is accessed.  
English-18  
DATA COPY  
To initiate data copy from the master monitor to the sub monitor(s), select “DATA COPY” and touch “SELECT”.  
A “PROCEEDING...” indicator will appear on the screen.  
NOTE: This function is only intended for the master monitor in ControlSync.  
All of the settings specified in the ControlSync chart (see page 10) will be copied from the master monitor to  
the sub monitor(s).  
CUSTOMIZE SETTING  
Store the current settings for easy recovery.  
To store current settings: Touch “SELECT”. After a warning message appears, touch “RESET”, current settings are  
stored.  
To restore settings: Hold “MENU” for 3 seconds or more while the OSD menu is off.  
ECO Information  
CARBON SAVINGS: Displays the estimated carbon savings information in kg.  
CARBON USAGE: Displays the estimated carbon usages information in kg. This is the arithmetic estimation, not  
actual measurement value.  
COST SAVINGS: Displays the electricity cost savings in balance.  
CARBON CONVERT SETTING: Adjusts the carbon footprint factor in the carbon saving calculation. This initial setting  
is based on the OECD (2008 Edition).  
CURRENCY SETTING: Displays electricity pricing in 6 currency units.  
CURRENCY CONVERT SETTING: Displays electricity savings in kW/hour (US Currency is default).  
NOTE: This model’s initial setting is “Currency = US$” and its Currency Convert setting = $0.11.  
This setting can be changed by using the ECO information menu.  
If you want to use the French setting, please refer to steps below:  
1. Touch the Menu key and select the ECO information menu using the “LEFT” or “RIGHT” key.  
2. Select CURRENCY SETTING item by touching the “UP” or “DOWN” key.  
3. The French currency unit is Euro ( ). You can adjust currency setting to Euro icon ( ) from US dollar ($)  
by touching the “LEFT” or “RIGHT” key in Current setting item.  
4. Select CURRENCY CONVERT SETTING by touching the “UP” or “DOWN” key*.  
5. Adjust CURRENCY CONVERT SETTING by touching the “LEFT” or “RIGHT” key.  
* This initial Euro ( ) setting is based on the OECD data for Germany (2007 Edition).  
Please check the receipt of electricity prices for France or OECD data for France.  
The French value according to the OECD data (2007 Edition) was 0.12.  
Information  
Provides information about the current resolution display and technical data including the preset timing being used and  
the horizontal and vertical frequencies. Indicates the model and serial numbers of your monitor.  
OSD Warning  
OSD warning menus disappear when EXIT is selected.  
NO SIGNAL: This function gives a warning when there is no horizontal or vertical sync. After power is turned on or  
when there is a change of input signal, the No Signal window will appear.  
OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After the power  
is turned on or there is a change of input signal or if the video signal doesn’t have proper timing, the Out Of Range  
menu will appear.  
English-19  
Specifications  
Monitor Specifications  
MultiSync EA245WMi-2  
Notes  
LCD Module  
Diagonal: 61.13 cm/24 inches  
Viewable Image Size: 61.13 cm/24 inches  
Native Resolution (Pixel Count): 1920 x 1200  
Active matrix; thin film transistor (TFT) liquid crystal  
display (LCD); 0.270 mm dot pitch; 300 cd/m2 white  
luminance; 1000:1 contrast ratio (typical), (5000:1  
Contrast ratio, Dynamic).  
Input Signal  
DisplayPort:  
DisplayPort Connector: Digital RGB  
DVI-D 24pin: Digital RGB  
DisplayPort V1.2 (HDCP 1.3)  
DVI (HDCP 1.4)  
DVI:  
VGA:  
15pin Mini D-sub: Analog RGB  
Sync  
0.7 Vp-p/75 ohm  
Separate sync.TTL level Positive/Negative  
Composite sync.TTL level Positive/Negative  
Sync on Green  
(Video 0.7 Vp-p and Sync Negative 0.3 Vp-p)  
HDMI:  
HDMI Connector: Digital YUV  
Digital RGB  
HDMI (HDCP 1.4)  
Output Signal  
DisplayPort:  
DisplayPort Connector: Digital RGB  
16,777,216  
DisplayPort V1.2 (HDCP 1.3)  
Display Colours  
Synchronization Range  
Horizontal: 31.5 kHz to 95.0 kHz  
Vertical: 56 Hz to 75 Hz  
Automatically  
Automatically  
Viewing Angle  
Left/Right:  
Up/Down:  
89° (CR > 10)  
89° (CR > 10)  
Image Formation Time  
Resolutions Supported  
6 ms (Gray to gray Typ.)  
720 x 400*1: VGA text  
Some systems may not support all modes listed.  
640 x 480*1 @ 60 Hz to 75 Hz  
800 x 600*1 @ 56 Hz to 75 Hz  
832 x 624*1 @ 75 Hz  
1024 x 768*1 @ 60 Hz to 75 Hz  
1152 x 870*1 @ 75 Hz  
1280 x 1024*1 @ 60 Hz to 75 Hz  
1400 x 1050*1 @ 60 Hz to 75 Hz  
1440 x 900*1 @ 60 Hz  
1600 x 1200*1 @ 60 Hz  
1680 x 1050*1 @ 60 Hz  
1920 x 1080*1 @ 60 Hz  
1920 x 1200 @ 60 Hz...........................................NEC DISPLAY SOLUTIONS cites recommended.  
Active Display Area  
USB Hub  
Landscape: Horiz.: 518.4 mm/20.4 inches  
Vert.: 324.0 mm/12.8 inches  
Portrait: Horiz.: 324.0 mm/12.8 inches  
Vert.: 518.4 mm/20.4 inches  
I/F: USB Specification Revision 3.1 Gen 1  
Port: Upstream 1  
USB 3.1 Gen 1 Downstream 3  
USB 3.1 Gen 1 Upstream port applicable to USB  
monitor control.  
Load Current: Maximum 0.9 A per port for USB 3.1 Gen 1  
AUDIO  
AUDIO Input:  
STEREO Mini Jack: Analog Audio  
DisplayPort Connector: Digital Audio  
HDMI Connector: Digital Audio  
Stereo L/R 500mV rms 20 Kohm  
PCM 2ch 32, 44.1, 48 kHz (16/20/24bit)  
PCM 2ch 32, 44.1, 48 kHz (16/20/24bit)  
Headphone Output: STEREO Mini Jack:  
Headphone Impedance 32 Ohm  
Speakers  
Practical Audio Output: 1.0 W + 1.0 W  
ControlSync  
(available up to 24 sub monitors)  
IN: Stereo Micro jack 2.5 φ  
OUT: Stereo Micro jack 2.5 φ  
Power Supply  
AC 100-240 V ~ 50/60 Hz  
0.90 - 0.50 A  
Current Rating  
Dimensions  
Landscape: 531.5 mm (W) x 365.4 - 515.4 mm (H) x 250.0 mm (D)  
20.9 inches (W) x 14.4 - 20.3 inches (H) x 9.8 inches (D)  
Portrait: 347.8 mm (W) x 549.5 - 613.2 mm (H) x 250.0 mm (D)  
13.7 inches (W) x 21.6 - 24.1 inches (H) x 9.8 inches (D)  
Height Adjustment: 150 mm/5.9 inches (Landscape orientation)  
63.7 mm/2.5 inches (Portrait orientation)  
Weight  
6.7 kg (14.8 lbs)/Without stand: 4.2 kg (9.3 lbs)  
Environmental Considerations  
Operating Temperature: 5°C to 35°C/41°F to 95°F  
Humidity: 20% to 80%  
Altitude: 0 to 16,404 Feet/0 to 5,000 m  
Storage Temperature: -10°C to 60°C/14°F to 140°F  
Humidity: 10% to 85%  
Altitude: 0 to 40,000 Feet/0 to 12,192 m  
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal and  
necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on the screen is actually  
one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.  
NOTE:  
Technical specifications are subject to change without notice.  
English-20  
Features  
Fully Ergonomic Stand: Provides viewing flexibility with 150mm height adjustment, -5 ~ 35-degree tilt, 170-degree swivel to  
both right/left directions with cable management function and small footprint. Monitor head (display part) can touch stand base  
for lower position requirement.  
ErgoDesign Features: Enhanced human ergonomics to improve the working environment, protect the health of the user and  
save money. In addition to the fully ergonomic stand, examples include OSD controls for quick and easy image adjustment and  
lower emissions.  
Various Signal Interfaces: This model has various interfaces like Analog D-SUB, DVI-D, DisplayPort and HDMI.  
DisplayPort OUT: This monitor has a DisplayPort out connector for daisy-chain connection. Multiple monitors can be connected  
without complicated cable management.  
UNIFORMITY: This feature compensates for slight variations in the white uniformity level that may occur on the screen and  
improves the color and evens out the luminance uniformity of the display.  
Response Improve: Improved gray to gray response.  
Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a  
variety of standards.  
sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays  
and other peripherals. The sRGB, which is based on the calibrated color space, allows for optimal color representation and  
backward compatibility with other common color standards.  
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing  
the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically  
optimizing display performance.  
Intelligent Power Manager System: Provides innovative power-saving methods that allow the monitor to shift to a lower power  
consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and lowering the  
air conditioning costs of the workplace.  
VESA Standard Mounting Interface: Allows users to connect your MultiSync monitor to any VESA standard third party  
mounting arm or bracket.  
USB 3.1 Gen 1: USB 3.1 Gen 1 hub for faster communication with the workstation, e.g. using a USB memory stick.  
USB Monitor Control: Allow you to adjust each item through application software by connecting an USB cable.  
Human/Ambient Sensors: Controls screen brightness according to user presence and ambient light status for less power  
consumption.  
NaViSet Administrator 2 Software: Offers an expanded and intuitive graphical interface, allowing you to more easily adjust  
OSD display settings from network PC.  
Environmental Impact: Annual typical maximum operating carbon footprint of this monitor (world-wide average) is  
approximately 45.5 kg (calculated by: rated wattage x 8 hours per day x 5 days a week x 45 weeks per year x Power-to-Carbon  
conversion factor - conversion factor is based on OECD publication of global CO2 emissions 2008 Edition). This monitor has a  
manufacturing carbon footprint of approximately 51.2 kg.  
Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC  
for its monitors.  
ControlSync: Follow the steps of “DATA COPY” and copy the settings from the master monitor to the sub monitors  
by connecting the ControlSync cable. When the setting of the master monitor is adjusted, it is sent to the sub monitors  
automatically, providing easy setting controls in a multiple monitor environment.  
Customize Setting: Allows to store the current settings and recover stored settings.  
Low Blue Light: This monitor has a blue light reducing function. This means hazardous light from the monitor is substantially  
reduced and it allows to free from eyestrain (see page 17).  
Flicker Free: Special backlight system reduces flicker for less eyestrain.  
English-21  
Troubleshooting  
No picture  
The signal cable should be completely connected to the display card/computer.  
The display card should be completely seated in its slot.  
The monitor does not support DisplayPort converter adapter.  
When you use DisplayPort signal, check to make sure not to plug the input signal cable in DisplayPort out connector.  
Power Switch and computer power switch should be in the ON position.  
The monitor will automatically turn off by “POWER SAVE TIMER” function when “POWER SAVE TIMER” setting is “ON”  
and continuing power save mode for 2 hours. Please touch the power key.  
Check to make sure that a supported mode has been selected on the display card or system being used.  
(Please consult display card or system manual to change graphics mode.)  
Check the monitor and your display card with respect to compatibility and recommended settings.  
Check the signal cable connector for bent or pushed-in pins.  
Check the signal input.  
If the front LED is dark blue, check the status of the OFF MODE SETTING mode (see page 14) or Human sensor  
(see page 14).  
When using an HDMI input, please change “OVER SCAN”.  
Power Key does not respond  
Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.  
When something is stuck on the bezel, key becomes unresponsive.  
Image Persistence  
Image persistence is when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT  
monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period  
of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was  
displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should  
be turned off for one hour to erase the image.  
NOTE:  
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at  
regular intervals whenever the screen is idle or turning off the monitor when not in use.  
Message “OUT OF RANGE” is displayed (screen is either blank or shows rough images only)  
Image is displayed only roughly (pixels are missing) and OSD warning “OUT OF RANGE” is displayed: Either signal  
clock or resolution is too high. Choose one of the supported modes.  
OSD warning “OUT OF RANGE” is displayed on a blank screen: Signal frequency is out of range. Choose one of the  
supported modes.  
Image is unstable, unfocused or swimming is apparent  
Signal cable should be completely attached to the computer.  
Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment.  
When the display mode is changed, the OSD Image Adjust settings may need to be readjusted.  
Check the monitor and your display card with respect to compatibility and recommended signal timings.  
If your text is garbled, change the video mode to non-interlace and use 60Hz refresh rate.  
LED on monitor is not lit (no blue or amber color can be seen)  
Power Switch should be in the ON position and power cord should be connected.  
Increase LED BRIGHTNESS adjustment.  
Picture is not as bright  
Make sure ECO MODE and AUTO BRIGHTNESS are turned off.  
If the brightness fluctuates, make sure AUTO BRIGHTNESS is turned off.  
Signal cable should be completely attached.  
LCD brightness degradation occurs due to long-term usage or extreme cold conditions.  
When using an HDMI input, please change “VIDEO LEVEL”.  
If the brightness fluctuates, make sure DV MODE is set to STANDARD.  
Display image is not sized properly  
Use the OSD Image Adjust controls to increase or decrease the Coarse adjustment.  
Check to make sure that a supported mode has been selected on the display card or system being used.  
(Please consult display card or system manual to change graphics mode.)  
When using an HDMI input, please change “OVER SCAN”.  
Check to make sure that the appropriate resolution has been selected in H.RESOLUTION and V.RESOLUTION.  
English-22  
No Video  
If no video is present on the screen, turn the Power key off and on again.  
Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).  
Some display cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC power  
cord under low resolution with DisplayPort.  
When using an HDMI input, please change “OVER SCAN”.  
No Sound  
Make sure the speaker cable is proper connected.  
Check to see if mute is activated.  
Check the volume in the OSD menu.  
Check selected OSD’s Tools to “SOUND INPUT”, when DisplayPort or HDMI is in use.  
Brightness variations over time  
Change AUTO BRIGHTNESS to OFF and adjust brightness.  
NOTE:  
When AUTO BRIGHTNESS is set to ON, the monitor automatically adjusts brightness based on the environment.  
When the brightness of surrounding environment changes, the monitor will also change.  
Change DV MODE to STANDARD and adjust brightness.  
NOTE:  
When DV MODE is set to DYNAMIC, the monitor automatically adjusts brightness.  
USB Hub does not operate  
Check to make sure the USB cord is properly connected. Refer to your USB device User’s Manual.  
Check if the USB upstream port on the monitor is connected to the USB downstream port on the computer. And make  
sure the computer is ON.  
Human sensor does not work  
If human icon on SENSOR SETTING (HUMAN SENSING) is located on vermilion color, it is detected that there is  
person.  
Make sure there is no object in front of Human sensor.  
Make sure there is no equipment which radiating infrared rays in front of monitor.  
ControlSync does not work  
Check to make sure that ControlSync cable is connected correctly.  
Check to make sure that ControlSync cable is not in “loop” connection.  
Master monitor should be connected OUT connector only.  
Please use provided ControlSync cable.  
You can use up to 24 sub monitors via ControlSync.  
No picture in multiple monitor connection  
Check to make sure that the resolution has been lower than the recommended resolution setting.  
Check to make sure that the display card supports MST (multi-stream transport).  
The number of monitors daisy-chained through SST (single-stream transport) depends on HDCP contents limitation.  
Monitors should be connected by the included DisplayPort cable.  
Check to make sure that DP OUT MULTISTREAM is “AUTO” and BIT RATE setting is “HBR2” when using MST (multi-  
stream transport) (see page 17).  
Reproduced text looks blurred  
Make sure that a supported resolution has been selected on the display card or system being used.  
If in doubt, please refer to the user’s manual of the display card or system to change the resolution.  
English-23  
Using the Zoom Function  
Allows you to use the entire screen area, significantly expanding the size.  
Allows the picture displayed in the center to expand.  
SETUP  
1. Select FULL or ASPECT in EXPANSION to activate the Zoom function (see page 16).  
EXPANSION OFF  
2. Set a resolution via H.RESOLUTION or V.RESOLUTION (see page 16).  
Vertical expansion  
Horizontal expansion  
3. The image position can be moved from the center to left or right by selecting LEFT/RIGHT and upward or downward by  
selecting UP/DOWN (see page 15).  
Move to left or right  
Move upward or downward  
English-24  
Human sensing function  
Human sensing function reduces power consumption by detecting the movement of a person.  
The HUMAN SENSING has following two settings:  
MODE  
LIGHT  
DEEP  
HUMAN SENSING SETTING  
No person in front of the monitor  
BRIGHTNESS 0%  
1
2
Power saving mode  
Image of human sensing operation  
A. When the sensor detects no person in front of the monitor, the monitor stays on for a period of time which is set at HUMAN  
SENSING > START TIME (see page 15).  
B. The monitor displays a notification on the screen after the period of time.  
You can set notification screen at SENSOR INFORMATION (see page 18).  
C. After displaying a notification, If LIGHT is set at HUMAN SENSING, the monitor screen gets gradually darker then becomes  
0% brightness in the end.  
If DEEP is set at HUMAN SENSING, the monitor enters into power saving mode.  
D. When the sensor detects a person coming back, the monitor setting is automatically back from power saving mode to normal  
mode.  
NOTE:  
When LIGHT is set at HUMAN SENSING, the monitor screen gets gradually brighter then back to original brightness.  
E. The monitor returns to normal mode.  
A user leaves  
A user is back  
D
A
B
C
E
Normal mode  
Normal mode +  
notification  
Power save mode  
HUMAN SENSING  
(LIGHT/DEEP)  
Back to Normal mode  
English-25  
Using the Auto Brightness function  
The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient lighting within the  
room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly.  
The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.  
SETUP  
Use the following procedures to select the Brightness Range that the monitor will use when the Auto Brightness function is  
activated.  
1. Set the BRIGHTNESS level. This is the brightness level that the monitor will go up to when the ambient lighting level is  
highest. Select this setting when the room is at its brightest.  
Select ON in the AUTO BRIGHTNESS menu (Figure 1). Then use the front Keys to move the cursor up to the  
BRIGHTNESS setting. Choose the desired brightness level (Figure 2).  
Figure 1  
Figure 2  
2. Set the DARK level. This is the level of brightness that the monitor will go down to when the ambient lighting level is low.  
Make sure the room is at its darkest when setting this level.  
Then use the front Keys to move the cursor up to the BRIGHTNESS setting. Choose the desired brightness level (Figure 3).  
Figure 3  
When the “Auto Brightness” function is enabled the Brightness level of the screen changes automatically according to the  
lighting conditions of the room (Figure 4).  
BRIGHTNESS range  
BRIGHTNESS level set  
for the monitor to use  
when ambient lighting  
level is low.  
BRIGHTNESS level set for the  
monitor to use when ambient  
lighting level is high.  
Bright condition area  
room bright condition  
dark  
bright  
Dark condition area  
Screen Brightness value by Auto Brightness function  
Figure 4  
Lb: Border between bright and dim lighting conditions; set at factory  
L1: BRIGHTNESS level set for the monitor to use when ambient lighting level is high (L1>Lb)  
L2 : BRIGHTNESS level set for the monitor to use when ambient lighting level is low (L2<Lb)  
L1 and L2 are the brightness levels set by the user to compensate for changes in ambient lighting.  
English-26  
Manufacturer’s Recycling and Energy Information  
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s  
top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-  
friendly products, and always strive to help define and comply with the latest independent standards from agencies such as  
ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).  
Disposing of your old NEC product  
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of  
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely  
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures  
and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.  
All required information concerning the disposal of the product and country-specific information on recycling facilities can be  
found on our following websites:  
Energy Saving  
This monitor features an advanced energy saving capability. When a Display Power Management signal is sent to the monitor,  
the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.  
Mode  
Power consumption  
LED colour  
Blue  
Maximum Operation  
Normal Operation  
Energy Saving Mode  
Off Mode  
50 W  
22 W Default setting, USB/Audio sleeping  
Blue  
0.30 W*  
0.25 W  
Amber  
Unlit  
*: Factory settings.  
For additional information visit:  
For Energy Saving information: [Default setting: DP OUT MULTISTREAM/CLONE]  
For ErP requirement/For ErP (Network standby) requirement:  
Setting: Tools  
Power consumption: 0.5 W or less.  
Time for power management function: Approx. 1 min.  
DP OUT MULTISTREAM  
CLONE  
WEEE Mark (European Directive 2012/19/EU and amendments)  
Disposing of your used product: In the European Union  
EU-wide legislation as implemented in each Member State requires that used electrical and electronic products  
carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors  
and electrical accessories, such as signal cables or power cords. When you dispose of such products, please  
follow the guidance of your local authority or ask the shop where you purchased the product, or if applicable,  
follow applicable legislation or agreement you may have. The mark on electrical and electronic products may  
only apply to the current European Union Member States.  
Outside the European Union  
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority  
and ask for the correct method of disposal.  
English-27  

Trane New Stylus Ms Svn015 En User Manual
Savin 5502 User Manual
Samsung Aw12p1hea User Manual
Samsung Aw07ph Series User Manual
KENWOOD MAJOR KM010 User Manual
GE AHH12 User Manual
FWE PHTT 12 User Manual
D LINK DCS 6100LH User Manual
BLACK DECKER RO400G User Manual
ASUS U330C User Manual