Moog Automobile Parts 813 User Manual

Rotary Servo Actuators • Linear Actuators • Amplifiers • Transducers  
A complete product line of actuator solutions for  
the most demanding applications.  
• Military and Commercial Aircraft  
Target Drones  
• Unmanned Vehicles  
• Military Land and Sea Vehicles  
• Military Security Applications  
Rotary Servo Actuators  
• Weight: 3 lbs  
Model 915  
Front flange mount  
The Model 915  
Rotary Servo  
Actuator is used to  
position the control  
surfaces of the QF-4  
unmanned air vehicle and is designed  
to operate under extreme environmental  
conditions.  
Peak torque: 300 in-lb  
SmCo permanent magnet DC motor  
Electronic position and torque limiting  
Film position transducer  
Position output signal  
Stroke: ±46º electrical stroke  
No-load speed: 180 deg/sec  
Bandwidth to 8 Hz  
MTBF: 5000 hr  
Model 940  
The Model 940 Rotary  
Brushless Actuator is  
qualified for airborne  
applications to control the  
rotational function of the  
aircraft’s targeting system.  
The actuator operates as a  
position servo with an external controller.  
±10 VDC input command signal  
Current output signal  
Low backlash  
Size: 4.95 x 4.5 x 6.2 inches  
Power: 28 VDC  
Robust structural design  
Mechanical stops  
Weight: 7 lbs  
High efficiency steel gearing  
No load speed: 160-220 deg/sec  
Stroke: ±46°  
Peak torque: 300 in-lbs  
Analog command input  
Electronic position and torque limiting  
Film position transducer  
Output shaft disconnect clutch  
Low backlash  
•Size: 3.188 x 3.15 x 4.69 inches long from  
back of brake to rear of mounting flange  
•Power: 270 VDC  
Model 905-01/-04  
The Model 905 Rotary Servo Actuator  
is used to position the control surfaces  
of the AQM-37D target drone and is  
designed to operate under extreme  
environmental conditions.  
•Rated Power Point: 165 in lb @ 231 rpm  
•Weight: 2.8 lbs  
±10 VDC input command signal  
Robust structural design  
High efficiency steel gearing  
Position output signal  
No load speed: 250 deg/sec  
Stroke: ±46°  
•Rare earth brushless DC resolver  
commutated motor with thermister  
•Fail-safe electromagnetic brake  
•Robust structural design  
•Low endplay  
Model 935  
•High efficiency planetary steel gearing  
•Front flange mount (rear surface)  
•Stroke: continuous rotation  
•Stall torque: 190 in lbs minimum  
•No-load speed 312 rpm  
The Model 935 Rotary  
ServoActuator is used  
to position the control  
surfaces plus utility  
applications unmanned air vehicles.  
This unit is design to operate under  
demanding environmental requirements  
seen worldwide.  
Size: 2.3 x 4.9 x 5.4 inches  
Power: 28 VDC and ±15 VDC  
Power point: 150 in-lbs @ 175 deg/sec  
Weight: 3 lbs  
•1 & 5 speed position resolvers  
Peak torque: 300 in-lbs  
Analog command input  
SmCo permanent magnet DC motor  
Electronic position and torque limiting  
Film position transducer  
Fail-safe brake (-01 only)  
±10 VDC input command signal  
Low backlash  
Model 946-01  
(not for new designs)  
The Model 946  
Servo System  
which is  
qualified for use  
on the AQM-37C target is configured  
with three components: a servo amplifier  
Model 94610000, a RotaryAileronActuator  
Model 94620000 and a Rotary Canard  
Actuator Model 94630000. The servo  
accepts an analog command signal to  
control the actuators output position.  
Size: 2.33 x 4.80 x 5.60 inches  
Power: 28 VDC  
RatedPowerPoint:350inlbs@120deg/sec  
Weight: 3.2 lbs  
Stall torque: 600 in lbs  
SMCO permanent magnet DC brush  
motor or rare earth brushless DC motor  
±10 VDC analog input command  
R/C command option  
Robust structural design  
High efficiency steel gearing  
Mechanical stops  
RS-422/RS-485 command options  
Robust structural design  
Position output signal  
No load speed: 250 deg/sec  
Stroke: ±33°  
Size: 2.33 x 4.8 x 4.54 inches  
Voltage: 28 VDC and 28 VDC regulated  
Weight: 4 lbs  
Low endplay  
High efficiency steel gearing  
Position and current output signal  
Electronic position and torque limiting  
Non-jamming mechanical stops  
Film position transducer  
Analog command input  
• SmCo permanent magnet DC motor  
• Electronic position and torque limiting  
Moog Components Group  
Rotary Servo Actuators  
Film position transducer  
Canard E.M. brake  
Size: 2.2 x 2.6 x 6.8 inches  
Power: 150 VDC and ±15 VDC  
Power point: 21 in-lb @ 230 rpm  
Weight: 3.0 lbs  
Model 873  
The Model 873 Rotary BrushlessActuator  
is used to control  
the rotational  
function of the  
aircraft’s night  
Low backlash  
Robust structural design  
High efficiency steel gearing  
Position output signal  
Peak torque: 46 in-lbs  
±10 VDC analog command input  
SmCo permanent magnet DC brushless  
motor  
vision targeting  
system.  
Stroke: ±36.5° Aileron  
43.8° CW Canard / 29.2° CCW Canard  
Size: 1.6 x 3.5 x 5.8 inches  
Power: 150 VDC and ±15 VDC  
Power point: 40 in-lb @ 621 rpm  
Weight: 3.9 lbs  
•1 speed resolver  
Tachometer  
Fail-safe brake  
Very low backlash  
Peak torque: 135 in-lbs  
±10 VDC analog command input  
SmCo permanent magnet DC  
brushless motor  
Robust structural design  
High efficiency steel gearing  
No load speed: 320 rpm  
Model 980-10 and 980-20  
The Model 980 Rotary Brushless Actuator  
System is an antenna azimuth drive servo  
actuator system consisting of the actuator  
motor/gearhead, separate controller and  
interconnecting cables. The system is used  
for ground vehicle radar applications in full  
and sector scan modes.  
•1 & 16 speed resolver  
Fail safe brake  
Model 905-30  
The Model 905-30  
Rotary Servo  
Actuator is used  
Very low backlash  
Robust structural design  
High efficiency steel gearing  
No load speed: 660 rpm  
to position the  
control surfaces of a  
reconnaissance unmanned  
air vehicle and is designed to operate  
under extreme environmental conditions.  
• Size: 4.06 x 4.06 (over mounting flange)  
x 14.00 inches from rear of motor  
assembly to front of mounting  
flange (Model 98000000-10 Actuator)  
• Size:11.0 x11.0 mounting base x 7.00  
inches high (Model 98000000-20 Drive  
Controller)  
Model 874  
The Model 874 Rotary  
Brushless Actuator is  
used to control the  
derotational function  
of the aircraft’s night  
vision targeting system.  
Size: 2.3 x 4.9 inch foot print and 5.4  
inches long  
Power: 28 VDC  
Power point: 150 in-lb @ 25 rpm  
Weight: 3.0 lbs  
• Rated Power Point: 168 in lb @ 183 rpm  
• Weight: 17.3 lbs actuator only  
• Input Power: 3 Phase 120/208 400 Hz  
• Rare earth brushless DC Hall sensor  
commutated motor with thermistors  
• Encoder rate feedback  
• Size: 1.25 x 2.35 x 4.0 inches  
Power: 150 VDC and ±15 VDC  
• Power point: 12 in-lb @ 660 rpm  
Weight: 1.4 lbs  
Peak torque: 300 in-lbs  
±10 VDC analog command input  
Brushless permanent magnet DC motor  
Electronic position and torque limiting  
Film position transducer  
Position output signal  
Current output signal  
• Peak torque: 30 in-lbs  
±10 VDC analog command input  
SmCo permanent magnet DC  
brushless motor  
• Robust structural design  
• Low endplay  
Low backlash  
• High efficiency planetary steel gearing  
• Front flange mount  
• 1 speed resolver  
Robust structural design  
High efficiency steel gearing  
Mechanical stops  
Tachometer  
• Stroke: continuous rotation  
• Stall point: 1,650 in lbs  
• Very low backlash  
• Robust structural design  
• High efficiency steel gearing  
• No load speed: 790 rpm  
Bandwidth to 10 Hz  
• No-load speed: 230 rpm (limited by  
controller)  
No load speed: 35 rpm  
Stroke: ±46°  
• Scan, sector and stare modes  
• Bit test outputs  
Model 917  
Our military  
qualified Model  
Model 875  
The Model  
875 Rotary  
• Separately package drive controller  
that accepts RS-232 commands  
917 Rotary  
Brushless  
Actuator is an azimuth drive servo for an  
airborne rate and position antenna  
Brushless Actuator is used to control the  
shroud function of the aircraft’s night vision  
targeting system.  
Moog Components Group  
Rotary Servo Actuators  
Model 971  
system. The Model 918 Servo Actuator  
provides the pitch roll-yaw functioning for  
• Size: 3.055 x 3.055 x 8.24 (961 only)  
Power point: 750 in-lb @ 30 rpm  
Weight: 13.6 lbs  
Our military qualified Model 971 Rotary,  
Brushless,Stepper  
Motor. Limited  
Rotation Trim  
Actuator for the  
this system.  
Peak torque: 1100 in-lbs  
• Qualified design  
Size: 11.30 x 4.59 x 6.53 inches  
Power: 115 VRMs, 400 Hz  
Weight: 11 lbs  
Rugged construction  
military helicopter.  
Brushless permanent magnet DC motor  
Broad operating temperature range  
E.M. brake with manual operation  
150 VDC system  
Command: ±10 VDC  
Size: 3.0 x 3.48 x 6.56 inches  
Power: 28 VDC  
Position feedback: resolver  
• High efficiency steel gearing  
Rate feedback: brushless DC tachometer  
Fail-safe brake: optional  
Inertial loads: to 4200 lbs-in2  
Scan Modes: 48, 91, 96, 153, 160, 320  
480 and 960 rpm  
Weight: 3.2 lbs  
Holding torque: 200 in-lbs  
Command: four phase stepper motor  
control from an external amplifier  
Stroke: ±30°  
±10 VDC position command signal  
No load speed: 40 rpm  
Model 965  
The Model 965 Rotary  
Servo Actuator is  
used to position the  
control surfaces plus  
utility applications in  
unmanned air vehicles.  
This unit is designed to operate under the  
demanding environmental requirements  
seen worldwide.  
Step rate: 1 rpm  
Sector Mode : ±48°  
Step size: 0.1°  
Bit test outputs  
Load rate: 15 in-lbs @ 0.6 rpm  
Eddy current damper  
Backlash: 0.15°  
• Robust structural design  
• MTBF: 5000 hrs  
Model 918  
Our military  
qualified Model  
• MTBF: 5000 hrs  
Model 993  
918 Rotary Brushless  
Stepper Actuator controls  
the pitch-roll-yaw function of an antenna  
system in conjunction with the Model 917  
azimuth drives.  
Our Model  
993 Rotary  
Servo Actuator  
provides mechanical  
valve control of the  
aircraft’s hydraulic flight control surfaces.  
Size: 3.50 x 7.10 x 8.90 inches long from  
front of mounting flange to rear of housing  
Power: 28 VDC  
Rated Power Point: 2200 in lbs @ 35  
deg/sec  
Size: 4.06 x 2.50 x 4.35 inches  
Power: 20 VDC  
Weight: 10.7 lbs  
Size: 4.10 inch diameter x 7.9 inches  
Power: 28 VDC  
Peak torque: 2500 in lbs  
• SMCO permanent magnet DC brush motor  
±10 VDC analog input command  
Robust structural design  
Low endplay  
Weight: 2 lbs  
• Power point: 200 in-lb @ 96 deg/sec  
• Weight: 7.4 lbs  
Command: ±10 VDC  
No-load speed: 300 rpm  
Fail-safe brake: none  
Inertial loads: 3 lb-in2  
Position accuracy: ±0.5°  
Backlash: 30 arc-minutes  
MTBF: 5000 hrs  
• Peak torque: 205 in-lb  
Brushless motor with Hall sensor  
electronic commutation  
High efficiency steel gearing  
Position output signal  
• Brushless RVDT position transducer  
• Derived tach signal  
Electronic position and torque limiting  
Non-jamming mechanical stops  
Film position transducer  
Front flange mount  
• BIT logic outputs  
Stroke: ±3600°  
• Robust structural design  
• Clutched output  
Robust structural design  
High efficiency steel gearing  
Stroke: ±45º electrical stroke  
Bandwidth to 8 Hz  
• High efficiency spur gearing  
• Pulse width modulated motor power  
Tach signal output  
Model 961 and 962  
OurModel961RotaryActuatorinconjunction  
with the Model 962 Transconductance  
Amplifier may be used for the antenna’s  
azimuth and elevation rotary function, or  
similar high torque applications.  
No-load speed: 87 deg/sec  
MTBF: 5000 hr  
• ±10 VDC input command signal to  
position signal output  
Torque output limit electronics  
• Position or rate servo operation  
• Low backlash  
• High reliability - 60,000 hour MTBF  
• No load speed: 110 deg/sec  
• Stroke: ±120°  
Moog Components Group  
Rotary Servo Actuators / Linear Actuators  
Model 995  
Robust structural design  
• Power: 28 VDC  
Our 995 Rotary  
Servo Actuator  
• Worm and worm wheel output (irreversible)  
High efficiency spur gearing  
Tach signal output  
• Rated power point:  
185 lb @ 1.60 in/sec (Model 801)  
350 lb @ 1.50 in/sec (Model 973)  
• Weight: 6.3 lb  
provides mechanical  
control of the  
aircraft’s rudder yaw  
dampening function  
during autopilot engagement.  
Torque output limit electronics  
Low backlash  
• Two NFeB permanent magnet DC brush  
motor/tachometers  
High reliability - 60,000 hour MTBF  
Mechanical interface with cable shaves,  
clutches and pilots throttle quadrant  
No load speed: 33 deg/sec  
• Size: 4.50 x 5.70 x 2.70 inches  
• Power: 28 VDC  
• Two RVDT’s  
• Robust structural design  
• Low endplay  
Power point: 60 in-lb @ 60 deg/sec  
• Weight: 3.96 lbs  
• High efficiency steel gearing  
• Monoball end-fitting mount  
• Ball screw/nut power screw assembly  
• Stroke:  
Linear Actuators  
Peak torque: 70 in-lb  
• Brushless motor with Hall sensor  
electronic commutation  
Linear Actuators translate rotary motion  
to linear motion. They have the same  
features and similar applications as rotary  
units.  
• Brushless RVDT position transducer  
• Derived tach signal  
(Model 801) 4.78 inches Electrical stroke  
(Model 973) 4.50 inches Electrical stroke  
• Stall load: 1,120 lbs  
• BIT logic outputs  
Model 310  
• Robust structural design  
• Clutched output  
The model 310  
Model 802  
linear actuator  
• High efficiency spur gearing  
• Pulse width modulated motor power  
Tach signal output  
The Model 802 Linear Servo Actuator  
is used to position the nacelles  
on a tilt rotor unmanned  
aerial vehicle during flight  
conversion modes. It is  
designed to operate  
under extreme  
environmental  
and endurance  
conditions.  
was designed  
to control the cyclic and collective feel on  
a helicopter.  
±10 VDC input command signal to  
position signal output  
• Size: 2.0 x 3.34 x 8.42 inches  
• Power: 28 VDC  
Torque output limit electronics  
Position or rate servo operation  
Low backlash  
• Power point: 300 lbs @ 0.45 in/sec  
• Weight: 4.5 lbs  
High reliability - 60,000 hour MTBF  
No load speed: 80 deg/sec  
Stroke: ±21°  
• Peak force: 1000 lbs  
Uses C-13 rare earth permanent magnet  
brush motor  
• Size: 3.33 x 3.56 x 17.44 inches long  
• Power: 28 VDC  
Limit switches  
Model 996  
The Model 996  
Rotary Servo  
Actuator provides  
auto throttle operation  
as derived by the  
aircraft’s flight control surfaces.  
• Stroke: 11.70 inches electrical stroke  
• Rated Power Point: 800 lb @ 0.75 in/sec  
• Weight: 8.0 lbs  
Robust design with steel gearing and  
power screw  
Environmentally sealed  
• EMI filter  
• Two NFeB permanent magnet DC brush  
motor/tachometers  
• Fail-safe brake  
• Two RVDT’s  
• No load speed: 0.6 in/sec  
• Stroke: 3 in  
• Robust structural design  
Size: 5.80 x 4.80 x 5.60 inches  
Power: 28 VDC  
• Low endplay  
• High efficiency steel gearing  
• Monoball fixed end fitting and two  
bushings on traveling nut for mounting  
• Ball screw/nut power screw assembly  
Power point: 210 in-lb @ 30 deg/sec  
Weight: 6.7 lbs  
Model 801/973  
The Model  
Peak torque: 220 in-lbs  
Brushless motor with Hall sensor  
electronic commutation  
• 26 VAC, 400 Hz synchro position  
transducer  
801/973 LinearServo Actuator is used to  
position the pitch of the rotor blades on a tilt  
rotor unmanned aerial vehicle. It is designed  
to operate under extreme environmental  
and endurance conditions. The controller  
servo amplifier is externally located.  
Model 974  
The Model 974 Linear Servo Actuator  
is used to position the nacelles on a tilt  
rotor unmanned aerial vehicle during  
flight conversion modes. It is designed to  
operate under extreme environmental and  
endurance conditions.  
±10 VDC rate signal  
(Model 801) Size: 3.25 x 3.56 x 10.42  
Derived tach signal  
inches retracted  
(Model 973) Size: 3.25 wide x 3.56 x  
11.17 inches retracted  
BIT logic outputs  
Moog Components Group  
Linear Actuators / Amplifiers / Transducers  
Model 933-01  
The flap position  
Transducers  
Transducers have been employed on both  
military and commercial aircraft to provide  
position feedback information of flight  
control surfaces to the flight computers,  
autopilots and cockpit displays.  
transducer is used in  
C-5 military transports  
to convert the  
mechanical position of  
the flaps to appropriate  
Size: 3.88 x 4.75 x 14.75 inches long  
Power: 28 VDC  
electrical signals for position indication.  
Model 800-XX  
• Rated power point: 1500 lb @ 0.26 in/sec  
Weight: 8.1 lbs  
• Input voltage: 26 VAC, 400 Hz  
• Consists of 2 synchros and input shaft  
• 4:1 gearing  
Our Model 800 Series Position  
Transmitter monitors the stabilizer position  
of the Boeing 757 and 767 commercial  
aircraft.  
Two NFeB Permanent Magnet DC brush  
motors  
• Single electrical connector for interfacing  
the excitation voltages and the synchro  
ouput signals  
Two failsafe electromagnetic brakes  
Robust structural design  
Low endplay  
Model 943-XX  
High efficiency steel gearing  
The Model 943 Position  
Transmitter monitors  
the stabilizer position  
of the Boeing 747- 400  
commercial aircraft.  
Trunnion mount for fixed end and traveling  
nut endfitting  
Input voltage: 28 VRMS, 400 Hz  
Position switches (up to 6)  
Rotary variable differential transformer  
(RVDT)  
Ball screw/nut power screw assembly  
Stroke: 7.25 inches electrical stroke  
No-load speed: 0.87 in/sec  
Input voltage: 28 VRMS, 400 Hz  
Rotary variable differential transformer  
(RVDT)  
•1 speed synchro  
Amplifiers  
Flame arrestor  
Anti-backlash gearing  
•1 speed synchro  
Amplifiers are used to  
control the actuators when  
the drive electronics are  
located seperately outside  
the actuators.  
Robust structural design  
High efficiency steel gearing  
Size: 4 inch OD x 5.2 inches long  
• Flame arrestor  
Anti-backlash gearing  
Robust structural design  
High efficiency steel gearing  
Model 932-02  
Model 871-01  
The Model 932-02 is designed for shaft  
position sensing such as aileron and  
elevator cable position on the C5 military  
transport.  
Model 976  
150 VDC transconductance amplifier  
used with the Model 873 Rotary Actuator.  
The Model 976 position transducer  
monitors the position of the nacelle of  
an unmanned aerial vehicle (UAV).  
Model 911-01  
270 VDC brushless motor controller for a  
pump system on a military armored vehicle.  
Model 944-01  
Input voltage: 26 VAC, 400 Hz  
• Consists of 3 synchros and input shaft  
• 1:1 gearing  
150 VDC transconductance amplifier  
used with the Model 875 Rotary Actuator.  
Voltage 6 VAC, 3000 Hz  
• 5:4 gearing  
• Single electrical connector for interfacing  
the excitation voltages and the synchro  
output signals  
Model 962-01  
• Consists of two rotary variable  
differential transformers (RVDT)  
• Single electrical connector for  
interfacing the excitation voltages and  
RVDT output signals  
150 VDC transconductance amplifier  
used with the Model 961 Rotary Actuator.  
Moog Components Group  
Actuator Product Overview  
Product Type  
Rotary Actuator  
Rotary  
Model Number  
Size (inches)  
Load  
Stroke  
Weight  
Torque (in-lbs)  
100 in-lbs Peak  
320 in-lbs Rated  
80 in-lbs Rated  
808  
813  
817  
1.1 x 2.7 x 4.0  
4.33 dia. x 7.76  
1.6 x 4.51 x 5.0  
±51.5 Plus Others  
13 oz  
12.5 lbs  
2.8 lbs  
Rotary  
Continuous Rotation  
Rotary  
±30 Plus Others  
80 in-lbs Rated  
150 in-lbs Peak  
Rotary  
Rotary  
Rotary  
Rotary  
Rotary  
819 / 820  
865-66  
905-01 / -04  
915  
1.5 x 3.2 x 4.5  
2.3 x 4.75 x 5.0  
2.3 x 4.9 x 5.4  
4.95 x 4.5 x 6.2  
2.3 x 4.8 x 5.6  
±45 Plus Others  
2.8 lbs  
3 lbs  
300 in-lbs Stall  
±46  
150 in-lbs Rated  
300 in-lbs Peak  
±33  
3 lbs  
300 in-lbs Peak  
±46  
7 lbs  
350 in-lbs Rated  
600 in-lbs Peak  
935  
±46  
3.2 lbs  
Rotary  
Rotary  
Rotary  
940  
3.18 x 3.15 x 4.69  
2.33 x 4.8 x 4.54  
4.06 x 4.06 x 14.0  
165 in-lbs Rated  
150 in-lbs Stall  
168 in-lbs Rated  
Continuous Rotation  
2.8 lbs  
4 lbs  
946-01  
±36.5 Plus Others  
980-10 / 980-20  
Continuous Rotation  
Continuous Rotation  
17.3 lbs Act. Only  
40 in-lbs Rated  
130 in-lbs Peak  
Rotary  
Rotary  
Rotary  
Rotary  
873  
874  
1.6 x 3.5 x 5.8  
1.25 x 2.35 x 4.0  
2.2 x 2.6 x 6.8  
2.3 x 4.9 x 5.4  
3.9 lbs  
1.4 lbs  
3.0 lbs  
3.0 lbs  
12 in-lbs Rated  
30 in-lbs Peak  
Continuous Rotation  
Continuous Rotation  
21 in-lbs Rated  
46 in-lbs Peak  
875  
150 in-lbs Rated  
30 in-lbs Peak  
905-30  
±46  
Rotary  
Rotary  
917  
918  
11.30 x 4.59 x 6.53  
4.06 x 2.50 x 4.35  
32 oz-in @ 960 rpm  
5.8 oz-in @ 300 rpm  
Continuous Rotation  
11 lbs  
2 lbs  
±3600  
750 in-lbs Rated  
1,100 in-lbs Peak  
Rotary  
Rotary  
Rotary  
961 / 962  
965  
3.055 x 3.055 x 8.24  
3.50 x 7.10 x 8.90  
3.0 x 3.48 x 6.56  
Continuous Rotation  
13.6  
2,200 in-lbs Rated  
2,500 in-lbs Peak  
±45  
10.7 lbs  
15 in-lbs Rated  
200 in-lbs Stall  
971  
±30  
3.2 lbs Act. Only  
Rotary  
Rotary  
Rotary  
993  
995  
996  
4.10 Diameter x 7.9  
4.50 x 5.70 x 2.70  
5.80 x 4.80 x 5.60  
205 in-lbs Stall  
70 in-lbs Stall  
220 in-lbs Stall  
±120  
7.4  
3.96  
6.7  
±21  
Continuous Rotation  
3 in  
Force (lbs)  
Linear Actuator  
300 lbs Rated  
100 lbs Peak  
Linear  
310  
2.0 x 3.34 x 8.42  
4.5 lbs  
185 lbs Rated  
1,120 lbs Peak  
Linear  
Linear  
Linear  
Linear  
801  
802  
973  
974  
3.25 x 3.56 x 10.42  
3.33 x 3.56 x 17.44  
3.25 x 3.56 x 11.17  
3.88 x 4.75 x 14.75  
4.78 in  
11.70 in  
4.5 in  
6.3 lbs  
8.0 lbs  
6.3 lbs  
8.1 lbs  
800 lbs Rated  
350 lbs Rated  
1,120 lbs Stall  
1,500 lbs Rated  
7.25 in  
Specifications and information are subject to change without prior notice.  
© 2006 Moog Components Group MSG20004 7/06  
Note: Some specifications may vary slightly. Please contact us for any questions.  
Americas  
U.K.  
Europe  
Asia-Pacific  
Moog Components Group  
1213 North Main Street  
Blacksburg, VA 24060  
United States  
Moog Components Group  
30 Suttons Business Park  
Reading, Berkshire RG6 1AW  
England  
Moog GmbH  
Moog Japan Ltd.  
1-8-37 Nishi-Shindo  
Hiratsuka Kanagawa  
Japan 254-0019  
Hanns-Klemm-Strasse 28  
71034 Boeblingen  
Germany  
Tel: 540-552-3011  
Fax: 540-557-6400  
Tel: +44 (0) 118-966-6044  
Fax: +44 (0) 118-966-6524  
Tel: +49 7031-622-0  
Fax: +49 7031-622-100  
Tel: +81 463-55-3615  
Fax: +81 463-54-4709  
7/06  

York Df 072 User Manual
Toshiba Ras B16gkvp E User Manual
Schumacher Ss 15a2 Ob User Manual
Pitney Bowes Addressright Da950 User Manual
MIELE H 5040 BM User Manual
KENWOOD KDC X702 User Manual
CRAFTSMAN 678 29460 User Manual
BLACK DECKER NHT2218 User Manual
ASUS VIVOTAB 8 M81C User Manual
ACER AW216 User Manual