KDC-X702
KDC-X502
KDC-BT772HD KDC-BT572U
KMR-D772BT
CIND-SRETCERIVUERCTION MANUAL
AMMOPLID-TUENDER’LEECMTEPURLDOEICD
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below.
Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-X702/KDC-BT772HD/KMR-D772BT/KDC-X502/KDC-BT572U
Serial number
US Residents Only
Register Online
Register your Kenwood product at http://www.kenwood.com/usa/
© 2017 JVC KENWOOD Corporation
B5A-2116-00 (KN)
IC (Industry Canada) Notice
CAUTION
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to
comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be
installed and operated keeping the radiator at least 20cm or more away from person’s body.
ATTENTION
Note de IC (Industrie Canada)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence.
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices
d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet
une énergie RF très faible qui est considérée comme conforme sans évaluation de l’exposition maximale
autorisée (MPE). Cependant, il est souhaitable qu’il devrait être installé et utilisé en gardant une
distance de 20 cm ou plus entre le radiateur et le corps humain.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
Para cumplimiento de la IFT:
(For
/
/
)
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada”
Contains Bluetooth Module
FCC ID:
IC ID:
ZWY8350X
12033A-8350X
(For
/
)
Contains Bluetooth Module
FCC ID:
IC ID:
ZWY8811X
12033A-8811X
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
ii
Article 3
Conditions for Grant of License
SOFTWARE LICENSE AGREEMENT
1. When the User transfers the Product, it may also transfer the license to use the Licensed Software
embedded in the Product (including any related materials, updates and upgrades) on condition that
no original, copies or related materials continue in the possession of the User, and that the User shall
cause the transferee to comply with this Software License Agreement.
2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code
analysis works in connection with the Licensed Software.
The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is
copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions
which Users shall follow in order to use the Licensed Software.
The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the
Product in which the "Licensed Software" is embedded.
Article 4
Right pertaining to the Licensed Software
The Licensed Software may include the software which has been licensed to the Licensor directly or
indirectly from any third party. In such case, some third parties require the Users to follow their conditions
for use separately from this Software License Agreement. Such software shall not be subject to this
Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided
separately below.
Any and all copyrights and other rights pertaining to the Licensed Software and related documents
shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or
sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be
entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any
related documents.
Article 1
General Provision
Article 5
Indemnification of Licensor
The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case
referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User.
(the country where the User bought the Product(hereinafter the "Country")
1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User
or any third party due to the exercise of the license granted to the User under this Agreement, unless
otherwise restricted by law.
2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with
certain objective of the Licensed Software.
Article 2
License
1. The license granted under this Agreement shall be the right to use the Licensed Software in the
Product.
2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed
Software and any related documents, whether in whole or in part.
3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall
not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.
4. The User shall use the Licensed Software according to the directions described in the operation
manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright
Law or any other laws and regulations by applying whole or a part of the Licensed Software.
Article 6
Liability to Third Party
If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any
other intellectual property right that was caused by the User's use of the Licensed Software, the User shall
settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any
inconvenience it may cause.
Article 7
Confidentiality
The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof
or any other information to be granted under this Agreement, as well as the conditions of this Agreement
as has not yet entered the public domain, and shall not disclose or divulge the same to any third party
without approval of the Licensor.
iii
Article 8
Termination
Important Notice concerning the Software
-jansson
In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this
Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event:
(1) when the User violated any provision of this Agreement; or
(2) when a petition has been filed against the User for an attachment,
provisional attachment, provisional disposition or any other compulsory execution.
Copyright (c) 2009-2012 Petri Lehtinen <[email protected]>
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the "Software"), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify,
merge, publish, distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject to the following
conditions:
Article 9
Destruction of the Licensed Software
If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related
documents and copies thereof within two (2) weeks from such date of termination.
The above copyright notice and this permission notice shall be included in all copies
or substantial portions of the Software.
Article 10
Protection of Copyright
1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor
and the Original Rightholder, and in no event shall they be under the ownership of the User.
2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other
intellectual property rights.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
OTHER DEALINGS IN THE SOFTWARE.
Article 11
Export Restriction
1. It is prohibited to export the Licensed Software and any related documents outside the country of the User (including
transmission thereof outside the country of the User via Internet of other communication tools).
2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of
User and any other countries.
3. The User shall agree that the software will be subject to any and all applicable international and domestic laws (including
the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users,
the use by end-users and importing countries to be provided by the country of User and any other countries, and any other
governmental authorities).
Article 12
Miscellaneous
1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.
2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be
provided or settled upon good-faith consultation between the Licensor and the User.
3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from,
and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the
Tokyo District Court for its first instance.
iv
CONTENTS
BEFORE USE
BEFORE USE
IMPORTANT
2
3
4
•
To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe
Warning and Caution in this manual.
BASICS
GETTING STARTED
•
Please keep the manual in a safe and accessible place for future reference.
1 Select the display language
and cancel the demonstration
2 Set the clock and date
WARNING
•
•
Do not operate any function that takes your attention away from safe driving.
Do not ingest the battery, Chemical Burn Hazard
3 Set the initial settings
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
HD RadioTM tuner
6
8
RADIO
CD/USB/iPod/ANDROID
AUX
10
13
13
15
16
17
20
29
32
33
36
Caution
Volume setting:
Pandora®
•
•
Adjust the volume so that you can hear sounds outside the car to prevent accidents.
Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
iHeartRadio®
Spotify
General:
•
•
•
•
•
•
Avoid using the external device if it might hinder safe driving.
SiriusXM® Radio
BLUETOOTH®
AUDIO SETTINGS
DISPLAY SETTINGS
TROUBLESHOOTING
Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
USB rating for the USB cables from the rear of the unit is indicated on a label.
Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire
connected 41). Turn off the unit or change the source to STANDBY when parking at a low ceiling area.
Remote control (RC-406):
(
42)
(
•
•
•
Do not leave the remote control in hot places such as on the dashboard.
The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
REFERENCES
Maintenance
More information
How to read this manual
INSTALLATION/
CONNECTION
•
•
•
•
Operations are explained mainly using buttons on the faceplate of
.
39
43
English indications are used for the purpose of explanation. You can select the display language from the [FUNCTION] menu.
[XX] indicates the selected items.
(
5)
SPECIFICATIONS
(
XX) indicates references are available on the stated page.
2
ENGLISH
BASICS
Faceplate
Attach
Detach
Volume knob
Display window
Lights up when
Bluetooth connection
is established.
(
21)
Detach button
Auxiliary cable from the rear of the unit.
USB 1 cable from the rear of the unit.
How to reset
(For
/
/
)
Reset the unit within
5 seconds after
USB 2 cable from the rear of the unit.
detaching the faceplate.
Note: The highlighted area on the faceplate flashes when the unit enters searching status.
To
On the faceplate
Turn on the power
Press
.
*
• Press and hold to turn off the power.
Adjust the volume
Turn the volume knob.
Select a source
Press
repeatedly.
Change the display information
Press DISP repeatedly.
(
38, 39)
*
For
: The power will automatically turn off after 20 minutes when in standby mode (Auto Power Off).
3
ENGLISH
BASICS
GETTING STARTED
Remote control (RC-406)
This unit can be remotely controlled with an optionally purchased remote
control.
Remote sensor
(Do not expose to bright sunlight.)
1
Select the display language and cancel the demonstration
When you turn on the power for the first time (or [FACTORY RESET] is set to
Pull out the insulation sheet when
using for the first time.
[YES]
,
5), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME
KNOB”
1
Turn the volume knob to select [ENG] (English) or [SPA] (Spanish),
then press the knob.
: Remote control functions are not available.
[ENG] is selected for the initial setup.
Then, (except for
) the display shows: “CANCEL DEMO”
“PRESS” “VOLUME KNOB”.
Press the volume knob.
[YES] is selected for the initial setup.
Press the volume knob again.
“DEMO OFF” appears.
How to replace the battery
2
3
2
Set the clock and date
To
On the remote control
1
2
Press the volume knob to enter [FUNCTION].
Turn on the power Press and hold SRC to turn off the power.
Turn the volume knob to select [CLOCK], then press the knob.
( Pressing SRC does not turn on the power. )
To adjust the clock
3
4
Adjust the volume Press
or
.
Turn the volume knob to select [CLOCK ADJUST], then press the knob.
Turn the volume knob to make the settings, then press the knob.
Hour Minute
• Press and hold
the volume to 15.
to continuously increase
5
6
Turn the volume knob to select [CLOCK FORMAT], then press the knob.
Turn the volume knob to select [12H] or [24H], then press the knob.
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Select a source
Press SRC repeatedly.
4
ENGLISH
GETTING STARTED
To set the date
SYSTEM
7
Turn the volume knob to select [DATE FORMAT], then press the knob.
Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY], then press
the knob.
KEY BEEP
ON: Activates the keypress tone. ; OFF: Deactivates.
8
SOURCE SELECT
9
Turn the volume knob to select [DATE SET], then press the knob.
PANDORA SRC ON: Enables PANDORA 1/PANDORA 2/PANDORA in source selection. ;
OFF: Disables. 13)
10 Turn the volume knob to make the settings, then press the knob.
(
Day Month Year or Month Day Year
11 Press and hold
To return to the previous setting item, press
to exit.
IHEART SRC
ON: Enables IHEARTRADIO 1/IHEARTRADIO 2/IHEARTRADIO in source
selection. ; OFF: Disables. 15)
(
.
SPOTIFY SRC ON: Enables SPOTIFY 1/SPOTIFY 2/SPOTIFY in source selection. ;
OFF: Disables. 16)
3
(
Set the initial settings
BUILT-IN AUX ON: Enables AUX in source selection. ; OFF: Disables.
(
13)
1
2
3
Press
repeatedly to enter STANDBY.
Press the volume knob to enter [FUNCTION]
.
CD READ
1
2
: Automatically distinguishes between audio file disc and music CD. ;
: Forces to play as a music CD. No sound can be heard if an audio file disc
Turn the volume knob to select an item (see the following table),
then press the knob.
Repeat step 3 until the desired item is selected or activated.
Press and hold
is played.
4
5
F/W UPDATE
to exit.
UPDATE SYSTEM/UPDATE HD (for
F/W UPDATE YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not
xxxx/ activated).
F/W UPDATE For details on how to update the firmware, visit
Vxx <www.kenwood.com/cs/ce/>.
/
)
To return to the previous setting item, press
.
Default: XX
DISPLAY
EASY MENU
When entering [FUNCTION]...
ON: LCD DISPLAY zone illumination changes to white color. ;
OFF: LCD DISPLAY zone illumination remains as [COLOR SELECT] color.
FACTORY RESET YES: Resets the settings to default (except the stored station). ;
NO: Cancels.
(
•
32)
CLOCK
KEY zone illumination changes to light blue color when you enter
[FUNCTION], irregardless of the [EASY MENU] setting.
Refer to the illustration on page 32 for zone identification.
CLOCK DISPLAY
(Except for
)
•
ON: The clock time is shown on the display even when the unit is turned
TUNER SETTING
PRESET TYPE
off. ; OFF: Cancels.
NORMAL: Memorizes one station for each preset button in each band
(FM1/FM2/FM3/AM). ; MIX: Memorizes one station or SiriusXM channel
for each preset button, regardless of the selected band or SiriusXM
channel.
ENGLISH
ESPANOL
Select the display language for [FUNCTION] menu and music information
if applicable.
By default, [ENGLISH] is selected.
5
ENGLISH
GETTING STARTED
HD Radio™ tuner (for
/
)
You can tune in to both conventional and HD Radio broadcasts.
Register the marine remote ID (for
)
• To find HD Radio stations in your area, visit <http://www.hdradio.com>.
Applicable only when you connect Kenwood Marine Remote Control unit
(KCA-RC55MR, optional accessory) to this unit.
• For connection, 42, Connecting external components
.
• Refer also to the supplied instruction manual of the Kenwood Marine
Remote Control unit for more information.
Preparation:
Press
repeatedly to enter STANDBY, then press the volume knob
to enter [FUNCTION].
1
Turn the volume knob to select an item, then press the knob.
[SYSTEM] [REMOTE SETTING] [REMOTE ID SET]
Remote control ID list is displayed.
Search for a station
1
2
Press
Press
repeatedly to select HD RADIO.
repeatedly (or press
•
•
[YES] indicates that this ID is already registered.
/
on the remote
[NO] indicates that this ID is available.
control) to select FM1/FM2/FM3/AM.
Press S / T (or press S /
search for a station or channel.
2
Turn the volume knob to select an available ID [REMOTE ID1]
/
3
on the remote control) to
[REMOTE ID2]/[REMOTE ID3], then press the knob.
“REGISTERING” appears on the display window.
• To change the searching method for S / T: Press
repeatedly.
AUTO1 : Automatically search for a station or channel.
AUTO2 : Search for a preset station or channel.
MANUAL : Manually search for a station or channel.
• To store a station or channel: Press and hold one of the number
buttons (1 to 6).
• To select a stored station or channel: Press one of the number buttons
(1 to 6) (or press one of the number buttons (1 to 6) on the remote
control).
To register, on the Kenwood Marine Remote Control unit:
• Press ENTER to register as [REMOTE ID1]
• Press SRC to register as [REMOTE ID2]
• Press DISP to register as [REMOTE ID3]
Once the ID is registered, “COMPLETED” appears.
.
.
.
To delete the registered ID
1
2
3
Turn the volume knob to select an item, then press the knob.
[SYSTEM] [REMOTE SETTING] [REMOTE ID DELETE]
Turn the volume knob to select the ID to delete [ID1 DELETE]
/
[ID2 DELETE]/[ID3 DELETE], then press the knob.
Turn the volume knob to select [YES] to delete the selected ID, and
select [NO] to cancel.
• To exit, press and hold
.
• To return to the previous setting item, press
.
6
ENGLISH
HD Radio™ tuner (for
/
)
Receive an emergency alert message
Direct Access Tuning (using the remote control)
When an emergency alert message is received, it appears and remains on
the display until the user performs the “Ignore” function.
1
2
3
Press DIRECT to enter Direct Access Tuning.
Press the number buttons to enter a frequency.
• Press
message.
(or press SRC on the remote control) to ignore the alert
Press
to search for a station or channel.
The same emergency alert message will not interrupt again for 12 hours.
• To cancel, press or DIRECT.
• If no operation is done for 10 seconds after step 2, Direct Access Tuning
Display received emergency alert messages
is automatically canceled.
The received emergency alert messages are stored in the Alert Message
List, and you can check them later. While listening to the HD RADIO
source...
Select an HD Radio multicast channel
Many HD Radio stations offer more than one channel programming.
This service is called multicasting. While receiving HD Radio multicast
channels....
1
2
3
Press
to display the Alert Message List.
Turn the volume knob to select a message.
Press the volume knob to display the information related to the
message.
Press S / T to select your desired channel (HD1 to HD8).
“LINKING” appears while linking to a multicast channel.
4
Press
again to exit.
• “NO LIST” appears when the list is empty.
Receive an Emergency Alert message
• This feature can store up to four messages in the list.
• To clear the message list, set [FACTORY RESET] to [YES]
.
(
5)
You can receive an emergency alert message while listening to another
source or while in STANDBY, via HD Radio Broadcast.
Other settings
Activate emergency alert message reception
1
2
3
4
Press the volume knob to enter [FUNCTION]
Turn the volume knob to select an item
Repeat step 2 until the desired item is selected or activated.
Press and hold to exit.
.
1
2
3
4
5
Press the volume knob to enter [FUNCTION]
Turn the volume knob to select [TUNER SETTING], then press the knob.
Turn the volume knob to select [EMERGENCY ALERT] then press the knob.
Turn the volume knob to select [ON], then press the knob.
Press and hold to exit.
.
(
8), then press the knob.
,
To return to the previous setting item, press
.
• To deactivate emergency alert message reception, select [OFF] in step 4.
• To return to the previous setting item, press
.
7
ENGLISH
HD Radio™ tuner (for
/
)
RADIO (for
/
/
)
Default: XX
TUNER SETTING
IF BAND
AUTO: Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.) ; WIDE: Subjects to
interference noises from adjacent FM stations, but sound quality will not
be degraded and the stereo effect will remain.
AUTO MEMORY YES: Automatically starts memorizing 6 stations with good reception. ;
Search for a station
NO: Cancels.
•
Selectable only if [NORMAL] is selected for [PRESET TYPE]
.
(
5)
1
2
Press
Press
repeatedly to select RADIO.
repeatedly (or press
RECEIVE MODE Sets the receive mode of the HD Radio receiver.
/
on the remote
AUTO: Automatically tunes to analog broadcast when there is no digital
broadcast. ; DIGITAL: Tunes in to digital broadcast only. ; ANALOG: Tunes
in to analog broadcast only.
control) to select FM1/FM2/FM3/AM.
Press S / T (or press S /
search for a station.
3
on the remote control) to
CLOCK
• To change the searching method for S / T: Press
repeatedly.
AUTO1 : Automatically search for a station.
AUTO2 : Search for a preset station.
MANUAL : Manually search for a station.
TIME SYNC
ON: Synchronizes the unit’s time to the Radio Broadcast Data System
station time. ; OFF: Cancels.
• To store a station: Press and hold one of the number buttons (1 to 6).
• To select a stored station: Press one of the number buttons (1 to 6) (or
press one of the number buttons (1 to 6) on the remote control).
Direct Access Tuning (using the remote control)
1
2
3
Press DIRECT to enter Direct Access Tuning.
Press the number buttons to enter a frequency.
Press
to search for a station.
• To cancel, press
or DIRECT.
• If no operation is done for 10 seconds after step 2, Direct Access Tuning
is automatically canceled.
8
ENGLISH
RADIO (for
/
/
)
Available Program Type for [PTY SEARCH]
Other settings
SPEECH
:
NEWS
,
INFORM (information), SPORTS
,
TALK
,
LANGUAGE
,
REL TALK
,
1
2
Press the volume knob to enter [FUNCTION].
(religious talk), PERSNLTY (personality), PUBLIC
,
COLLEGE HABL ESP
Turn the volume knob to select an item (see the following table), then
press the knob.
(spanish talk), WEATHER
MUSIC
:
ROCK
(softrock), TOP 40
JAZZ
,
CLS ROCK (classic rock), ADLT HIT (adult hits), SOFT RCK
3
4
Repeat step 2 until the desired item is selected or activated.
,
COUNTRY OLDIES SOFT NOSTALGA (nostalgia),
,
,
,
Press and hold
to exit.
,
CLASSICL (classical), R & B (rhythm and blues), SOFT R&B
(soft rhythm and blues), REL MUSC (religious music), MUSC ESP
To return to the previous setting item, press
.
(spanish music), HIP HOP
The unit will search for the Program Type categorized under [SPEECH] or
[MUSIC] if selected.
Default: XX
TUNER SETTING
•
[MONO SET]/[TI]/[PTY SEARCH] is selectable only when the band is FM1/
AUTO MEMORY YES: Automatically starts memorizing 6 stations with good reception. ;
FM2/FM3.
NO: Cancels.
• If the volume is adjusted during reception of traffic information, the
adjusted volume is memorized automatically. It will be applied the next
time traffic information is turned on.
•
Selectable only if [NORMAL] is selected for [PRESET TYPE]
.
(
5)
MONO SET
TI
ON: Improves the FM reception, but the stereo effect may be lost. ;
OFF: Cancels.
ON: Allows the unit to temporarily switch to Traffic Information if
available (“TI” lights up). ; OFF: Cancels.
PTY SEARCH
Select the available Program Type (see the following), then press
S
/
T
to start.
CLOCK
TIME SYNC
ON: Synchronizes the unit’s time to the Radio Broadcast Data System
station time. ; OFF: Cancels.
9
ENGLISH
CD/USB/iPod/ANDROID
Start playback
The source changes automatically and playback starts.
CD
Label side
M
Eject disc
Selectable source:
•
/
/
: CD/USB 1/USB 2/iPod 1/iPod 2/ANDROID 1/
ANDROID 2
•
/
: CD/USB/iPod USB/ANDROID
To
On the faceplate
On the remote control
Playback/pause
Press
.
Press
.
4
*
Reverse/Fast-forward
Press and hold S / T.
Press S / T.
Press and hold S /
.
USB
Select a track/file
Press S /
.
5
*
Select a folder
Press
/
.
Press J / K.
USB 1 cable from the
rear of the unit
(USB input terminal).
CA-U1EX (max.: 500 mA)
(optional accessory)
6
*
Repeat play
Press
TRACK REPEAT
FILE REPEAT
repeatedly.
/ALL REPEAT
: Audio CD
/
FOLDER REPEAT
/
/
ALL REPEAT : MP3/WMA/AAC/WAV/
FLAC file
iPod/iPhone
KCA-iP102/KCA-iP103
(optional accessory)
FILE REPEAT
/
FOLDER REPEAT
REPEAT OFF : iPod or ANDROID
1
*
6
*
Random play
Press
DISC RANDOM
FOLDER RANDOM
repeatedly.
or accessory of the iPod/
/
2
*
iPhone
/
RANDOM OFF
: Audio CD
/
/
RANDOM OFF : MP3/WMA/AAC/WAV/FLAC file,
:
iPod or ANDROID
You can also connect to
the USB 2 cable from the
rear of the unit
(USB input terminal).
3
*
ANDROID
7
*
to select ALL RANDOM.
Press and hold
1
*
*
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
Do not leave the cable inside the car when not using.
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the
instructions to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application
on your Android device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.
2
3
2
*
USB cable
(commercially available)
10
ENGLISH
CD/USB/iPod/ANDROID
4
*
*
*
*
For ANDROID: Applicable only when [BROWSE MODE] is selected.
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.
For iPod/ANDROID: Applicable only when [MODE OFF]/[BROWSE MODE] is selected.
For CD: Only for MP3/WMA/AAC files.
Select a file from a folder/list
5
6
7
For iPod/ANDROID, applicable only when [MODE OFF]/[BROWSE MODE] is
selected.
1
2
3
Press
.
Select control mode
Turn the volume knob to select a folder/list, then press the knob.
Turn the volume knob to select a file, then press the knob.
While in iPod 1/iPod 2/iPod USB source, press 5 repeatedly.
MODE ON : Control iPod using the iPod itself. However, you can still play/
pause, file skip, fast-forward or reverse from this unit.
MODE OFF : Control iPod from this unit.
Quick Search (applicable only for CD, USB 1, USB 2, USB, ANDROID 1,
ANDROID 2 and ANDROID source)
If you have many files, you can search through them quickly.
While in ANDROID 1/ANDROID 2/ANDROID source, press 5 repeatedly.
BROWSE MODE : Control Android device from this unit via KENWOOD
MUSIC PLAY application installed in the Android device.
HAND MODE : Control Android device using the Android device itself via
other media player applications installed in the Android
device. However, you can still play/pause and file skip from
this unit.
Turn the volume knob quickly to browse through the list quickly.
Skip Search (applicable only for iPod 1, iPod 2, iPod USB, ANDROID 1,
ANDROID 2 and ANDROID source)
Press S / T to search at a preset skip search ratio.
[SKIP SEARCH])
(
12,
• Pressing and holding S / T searches at a 10 ratio.
%
Alphabet search (applicable only for iPod 1, iPod 2, iPod USB,
ANDROID 1, ANDROID 2 and ANDROID source)
Select music drive
You can search for a file according to the first character.
While in USB 1/USB 2/USB source, press 5 repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass Storage
Class).
For iPod 1/iPod 2/iPod USB source
1
Turn the volume knob quickly to enter character search.
Turn the volume knob to select the character.
2
• Selected drive of a multiple drives device.
• Select “ ” to search for a character other than A to Z, 0 to 9.
*
3
4
Press S / T to move to the entry position.
Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo
• You can enter up to 3 characters.
Press the volume knob to start searching.
While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the
iPod/iPhone to the USB input terminal of the unit.
• The unit will output the sound from these applications.
11
ENGLISH
CD/USB/iPod/ANDROID
Other settings
For ANDROID 1/ANDROID 2/ANDROID source
1
Press J / K to enter character search.
Turn the volume knob to select the character.
^A^: Upper case letters (A to Z)
_A_: Lower case letters (a to z)
-0-: Numbers (0 to 9)
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table),
then press the knob.
Repeat step 2 until the desired item is selected or activated.
Press and hold
2
3
4
to exit.
***: Character other than A to Z, 0 to 9
3
Press the volume knob to start searching.
To return to the previous setting item, press
.
• To return to the root folder/first file/top menu, press 5. (Not applicable for
BT AUDIO source.)
Default: XX
• To return to the previous setting item, press
.
USB
• To cancel, press and hold
.
MUSIC DRIVE DRIVE CHANGE: The next drive ([DRIVE 1] to [DRIVE 4]) is selected
automatically and playback starts.
Repeat steps to
1
3
to select the following drives.
Direct Music Search (using the remote control)
SKIP SEARCH 0.5% 1% 5%/10%: While listening to iPod 1, iPod 2, iPod USB,
/
/
1
2
3
Press DIRECT.
ANDROID 1, ANDROID 2 or ANDROID source, selects the skip search ratio over
the total files.
Press the number buttons to enter a track/file number.
Press
to search for music.
• To cancel, press
or DIRECT.
• Not available if Random Play is selected.
• Not applicable for iPod 1, iPod 2, iPod USB, ANDROID 1, ANDROID 2 and
ANDROID source.
Settings to use KENWOOD Remote application
KENWOOD Remote application is designed to control the KENWOOD car
receiver’s operations from the iPhone/iPod (via USB input terminal).
Preparation:
Install the latest version of KENWOOD Remote application on your device
before connecting. For more information, visit
<www.kenwood.com/cs/ce/>.
You can make the settings in the same way as connection via Bluetooth.
(
27)
12
ENGLISH
AUX
Pandora®
Preparation:
Preparation:
Select [ON] for [BUILT-IN AUX] for [SOURCE SELECT]
.
(
5)
Install the latest version of the Pandora application on your device
(iPhone/iPod touch), then create an account and log in to Pandora.
• Select [ON] for [PANDORA SRC] in [SOURCE SELECT]
.
(
5)
Start listening
1
Connect a portable audio player (commercially available).
Start listening
3.5 mm (1/8") stereo mini plug with “L”
shaped connector (commercially available)
1
2
Open the Pandora application on your device.
Connect your device to the USB input terminal.
Portable audio player
KCA-iP102/KCA-iP103
Auxiliary cable from
the rear of the unit
USB 1 cable from the rear
of the unit.
(optional accessory) 1 or
*
2
*
accessory of the iPod/iPhone
2
3
Press
repeatedly to select AUX.
Turn on the portable audio player and start playback.
/
/
: You can
Set the AUX name
also connect to the USB 2 cable from the rear of the unit.
While listening to a portable audio player connected to the unit...
3
Press
repeatedly to select PANDORA 1/PANDORA 2/
1
2
3
4
Press the volume knob to enter [FUNCTION].
PANDORA.
Turn the volume knob to select [SYSTEM], then press the knob.
Turn the volume knob to select [AUX NAME SET], then press the knob.
Turn the volume knob to select an item, then press the knob.
Broadcast starts automatically.
1
*
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
Do not leave the cable inside the car when not using.
AUX (default)/DVD/PORTABLE/GAME/VIDEO/TV
2
5
Press and hold
to exit.
To return to the previous setting item, press
.
13
ENGLISH
Pandora®
To
On the faceplate
On the remote control
Bookmark current song information
Playback/pause
Skip a track
Thumbs up or
Press
.
Press
Press
Press
.
Press and hold the volume knob.
“BOOKMARKED” appears and the information is stored to your device.
• The bookmark is available on your Pandora account but not on this
unit.
.
Press T.
/
.
Press J / K.
*
thumbs down
Delete a station
*
If thumbs down is selected, the current track is skipped.
While listening to PANDORA...
Create and save a new station
1
2
Press
.
Turn the volume knob to select [STATION DELETE], then press the
knob.
1
2
3
Press
.
Turn the volume knob to select [NEW STATION], then press the knob.
Turn the volume knob to select [FROM ARTIST] or [FROM TRACK], then
press the knob.
3
4
Turn the volume knob to select [SORT BY DATE] or [SORT BY A-Z], then
press the knob.
Turn the volume knob to select the desired station to delete, then
press the knob.
Turn the volume knob to select [YES], then press the knob.
Press and hold
A new station is created based on the artist or current song.
Press and hold one of the number buttons (1 to 5) to store.
4
5
6
to exit.
To select a stored station: Press one of the number buttons (1 to 5).
To return to the previous setting item, press
.
Search for a registered station
1
2
Press
.
Turn the volume knob to select an item, then press the knob.
[SORT BY DATE]: According to the registered date
[SORT BY A-Z]
:
By alphabetical order
3
4
Turn the volume knob (or press J/ K on the remote control) to
select the desired station.
Press the volume knob (or press
confirm.
on the remote control) to
To cancel, press and hold
.
14
ENGLISH
iHeartRadio®
Preparation:
To
On the faceplate
On the remote control
Install the latest version of iHeartAuto application on your device
(iPhone/iPod touch), then create an account and log in to iHeartRadio.
Playback/pause
Press
.
Press
Press
.
• Select [ON] for [IHEART SRC] in [SOURCE SELECT]
.
(
5)
Skip a track for
custom station
.
Press T.
Start listening
Thumbs up or
thumbs down
Press J / K.
( Not available )
( Not available )
1
2
Open the iHeartAuto application on your device.
Connect your device to the USB input terminal.
Create a new/custom Press 1.
station
Scan for live station
1
2
Press 2 to start
scanning.
Press 2 again
to listen to the
station.
( Not available )
KCA-iP102/KCA-iP103
USB 1 cable from the rear
of the unit.
(optional accessory) 1 or
*
2
*
accessory of the iPod/iPhone
Search and store a station
Press
1
2
3
.
/
/
: You can
Turn the volume knob to select a category, then press the knob.
Turn the volume knob (or press J/ K on the remote control) to
select the desired station.
Press the volume knob (or press
confirm.
also connect to the USB 2 cable from the rear of the unit.
3
Press
repeatedly to select IHEARTRADIO 1/IHEARTRADIO 2/
4
on the remote control) to
IHEARTRADIO.
Broadcast starts automatically.
When a city list appears, you can search cities in alphabetical order by
turning the volume knob quickly.
1
*
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
Do not leave the cable inside the car when not using.
2
To cancel, press and hold
.
To store a station: Press and hold one of the number buttons (3, 4 or 5).
To select a stored station: Press one of the number buttons (3, 4 or 5).
15
ENGLISH
Spotify
Preparation:
To
On the faceplate
On the remote control
Install the latest version of the Spotify application on your device (iPhone/
iPod touch), then create an account and log in to Spotify.
Playback/pause
Skip a track
Press
.
Press
.
• Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]
.
(
5)
4
4
*
*
Press S / T.
Press S /
.
Thumbs up or
thumbs down
Press
/
.
Press J / K.
Start listening
3
*
1
2
Open the Spotify application on your device.
Connect your device to the USB input terminal.
Start radio
Press and hold 5.
( Not available )
( Not available )
5
*
Repeat play
Press
repeatedly.
REPEAT ALL/REPEAT
4
*
ONE
/
REPEAT OFF
5
*
KCA-iP102/KCA-iP103
Random play
Press
repeatedly.
USB 1 cable from the rear
of the unit.
(optional accessory) 1 or
4
*
*
( Not available )
2
*
accessory of the iPod/iPhone
SHUFFLE ON/SHUFFLE
OFF
3
*
This feature is available for tracks in Radio only. If thumbs down is selected, the current
track is skipped.
Available for premium account users only.
Available for tracks in Playlists only.
/
/
: You can
also connect to the USB 2 cable from the rear of the unit.
4
*
5
*
3
Press
repeatedly to select SPOTIFY 1/SPOTIFY 2/SPOTIFY.
Broadcast starts automatically.
Save favorite song information
1
*
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
Do not leave the cable inside the car when not using.
While listening to the Radio on Spotify...
2
Press and hold the volume knob.
“SAVED” appears and the information is stored to “Your Music” or “Your
Library” on your Spotify account.
To unsave, repeat the same procedure.
“REMOVED” appears and the information is removed from “Your Music”
or “Your Library” on your Spotify account.
16
ENGLISH
Spotify
SiriusXM® Radio
Only SiriusXM® brings you more of what you love to listen to, all in one
place. Get over 140 channels, including commercial-free music plus the
best sports, news, talk, comedy and entertainment. Welcome to the world
of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required.
For more information, visit <www.siriusxm.com>.
Search for a song or station
1
2
Press
.
Turn the volume knob to select a list type, then press the knob.
The list types displayed differ depending on the information sent
from Spotify.
Preparation:
3
4
Turn the volume knob (or press J / K on the remote control) to
1
Connect the optional SiriusXM Vehicle Tuner (commercially
available).
select the desired song or station.
Press the volume knob (or press
confirm.
on the remote control) to
You can browse through the list quickly by turning the volume knob
quickly.
Antenna
To cancel, press and hold
.
SiriusXM Vehicle Tuner
Expansion port on
the rear panel
2
3
Check your Radio ID for activation.
The SiriusXM Radio ID is required for activation and can be found by
tuning to Channel 0 as well as on the label found on the SiriusXM
Connect tuner and its packaging.
The Radio ID does not include the letters I, O, S or F.
Activate the subscription.
For users in the U.S.A.:
Online: Go to <www.siriusxm.com>
Phone: Call 1-866-635-2349
For users in Canada:
Online: Go to <www.siriusxm.ca/activatexm>
Phone: Call 1-877-438-9677
4
Press
repeatedly to select SIRIUS XM to start updating.
17
ENGLISH
SiriusXM® Radio
Start listening
SiriusXM Keymode
1
2
3
Press
Press
Press
repeatedly to select SIRIUS XM.
repeatedly to select a band.
Press and hold
to change the keymode (channel or replay).
(Default: Channel keymode)
.
“
” lights up when replay keymode is selected.
“ ” lights up.
4
Turn the volume knob to select a category, then press the knob.
If “ALL CHANNELS” is selected, all the available channels will be
shown.
Turn the volume knob to select a channel, then press the knob.
(or)
Press S / T to search for a channel manually.
• Pressing and holding S / T changes the channel rapidly.
When channel keymode is selected...
To
On the faceplate
On the remote control
5
Select a channel
Press S / T.
Press S /
.
Change a channel
rapidly
Press and hold
S / T.
Press and hold S /
.
Store a channel of
the current band
Press and hold
one of the number
buttons (1 to 6).
( Not available )
If a locked channel or a mature channel is selected, a pass code input
screen appears. Enter the pass code to receive the channel.
(
19)
Select a stored
channel of the
current band
Press one of the number buttons (1 to 6).
To change the tuning method for S / T: Press
Each time you press , the tuning method switches between
.
“CHANNEL” (manually search for a channel) and “PRESET” (searches for a
preset channel of the selected band).
When replay keymode is selected...
To
On the faceplate
On the remote control
Playback/pause
Press
.
Press
.
Direct Access Tuning (using the remote control)
Skip backward/
forward
Press S / T.
Press S /
.
1
2
3
Press DIRECT to enter Direct Access Tuning.
Press the number buttons to enter a channel number.
Press
to start searching.
Rewind/Fast-forward Press and hold
Press and hold S /
S / T.
.
• To cancel, press
or DIRECT.
• If no operation is done for 10 seconds after step 2, Direct Access Tuning
Go to Live
Press 1.
is automatically canceled.
18
ENGLISH
SiriusXM® Radio
SmartFavorites and TuneStart™
SiriusXM settings
User stored channels are recognized as SmartFavorite channels*. The
SiriusXM Vehicle Tuner automatically buffers the broadcast content in the
background.
• SmartFavorites feature is available with SXV200 or later SiriusXM
Vehicle Tuner.
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table),
then press the knob.
3
4
Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
Press and hold
to exit.
*
SXV300 (and later) SiriusXM Vehicle Tuner can use all 18 stored channels as SmartFavorites.
The SXV200 SiriusXM Vehicle Tuner can use 6 stored channels from the current band as
SmartFavorites.
To return to the previous setting item, press
.
Default: XX
When you select a SmartFavorite channel, you can rewind and replay up
to 30 minutes of any of the missed news, talk, sports or music content.
• Playback starts from the beginning of the song if [TUNE START] is set to
[ON] ( 20) for most music channels stored as a SmartFavorite.
SIRIUS XM
CHANNEL LOCK
To unlock settings:
1
2
3
Turn the volume knob to select a number.
Press one of the number buttons (1 to 6) to select a stored channel.
Press S / T to move to the entry position.
Repeat steps
(Initial pass code is 0000.)
1
and to enter the current pass code.
2
TuneScan™
4
Press the volume knob to confirm.
You can get a short preview of the songs that you have missed on each of
your SmartFavorite music channels or currently tuned music channel.
CODE SET
1
2
3
4
5
•
Turn the volume knob to select a number.
Press S / T to move to the entry position.
Repeat steps
1
and to enter a new 4-digit pass code.
2
Press and hold to start scanning the first 6 seconds of the
recorded music contents.
Press the volume knob to confirm.
Repeat steps to to reconfirm the pass code.
1
4
Make a note of the new pass code to enter channel lock settings for
next time.
• To listen to the current song, press the volume knob to stop scanning.
The unit continues playing the current song.
• To select the previous/next song, press S / T.
• To cancel scanning, press and hold the volume knob. Playback returns
to the channel before you entered TuneScan.
LOCK SETTING
MATURE CH: Selects the SiriusXM-defined lock setting. ;
USER DEFINED: Selects the individual channels the user wants to
lock. ; OFF: Cancels.
19
ENGLISH
SiriusXM® Radio
BLUETOOTH®
BLUETOOTH — Connection
1
*
CHANNEL EDIT
1
2
Turn the volume knob to select a category, then press the knob.
Turn the volume knob to select a channel you want to lock, then
press the knob.
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
“L” appears in front of the channel number.
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
– Serial Port Profile (SPP)
3
Press and hold
to exit.
1
*
CHANNEL CLEAR
YES: Clears all the locked channels. ; NO: Cancels.
– Phonebook Access Profile (PBAP)
2
*
TUNE START
ON: All qualified music channels in the SmartFavorite will start
playback from the beginning of the song. ; OFF: Cancels.
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
– aptX codec (Qualcomm® aptX™) (for
)
SIGNAL LEVEL
Shows the strength (NO SIGNAL/WEAK/GOOD/STRONG) of the
current received signal.
/
/
BUFFER USAGE
SXM RESET
1
Shows the memory usage (0% to 100%) for Replay buffer.
YES: Resets stored channel and lock setting to default. ; NO: Cancels.
*
*
Displayed only when [USER DEFINED] is selected.
Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports
SmartFavorites.
Connect the microphone
2
MIC (microphone input terminal)
Microphone
(supplied)
Rear panel
Adjust the microphone angle
Secure using cord clamps
(not supplied) if necessary.
20
ENGLISH
BLUETOOTH®
Pair and connect a Bluetooth device for the first time
Auto Pairing
1
2
Press
to turn on the unit.
When you connect iPhone/iPod touch/Android device to the USB input
terminal, pairing request (via Bluetooth) is automatically activated.
Search and select this unit model name (KDC-X7**/KDC-BT7**HD/
KMR-D7**BT/KDC-X5**/KDC-BT5**U) on the Bluetooth device.
“PAIRING” “PASS XXXXXX” Device name “PRESS” “VOLUME
KNOB” appears on the display.
Press the volume knob to pair once you have confirmed the device
name.
• For some Bluetooth devices, you may need to enter the Personal
Identification Number (PIN) code immediately after searching.
Press the volume knob to start pairing.
Automatic pairing request is activated only if:
3
– Bluetooth function of the connected device is turned on.
“PAIRING OK” appears when pairing is completed.
–
[AUTO PAIRING] is set to [ON]
.
(
26)
– KENWOOD MUSIC PLAY application is installed on the Android device
Once pairing is completed, Bluetooth connection is established
automatically.
• “BT1” and/or “BT2” indicator on the faceplate lights up.
(
10) and [BROWSE MODE] is selected.
(
11)
• This unit supports Secure Simple Pairing (SSP).
• Up to five devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device will remain
registered in the unit even if you reset the unit. To delete the paired
device, 25, [DEVICE DELETE]
.
• A maximum of two Bluetooth phones and one Bluetooth audio device
can be connected at any time.
However, while in BT AUDIO source, you can connect to five Bluetooth
audio devices and switch between these five devices.
(
27)
• Some Bluetooth devices may not automatically connect to the unit
after pairing. Connect the device to the unit manually.
• Refer to the instruction manual of the Bluetooth device for more
information.
21
ENGLISH
BLUETOOTH®
BLUETOOTH — Mobile phone
Connect with a remote device by One-touch (NFC)
(for
/
/
)
Near Field Communication (NFC) enables short-range wireless
communication between the unit and remote devices such as
smartphones.
By holding an NFC-compatible remote device near to the N-Mark on
the unit (right side of the panel), the unit and remote device proceed
to complete pairing and established the BLUETOOTH connection
automatically.
KEY
Receive a call
1
2
Activate the NFC function on the remote device.
Refer to the instruction manual of the remote device for more
information.
Hold the remote device near to the N-Mark on the unit (right side of
the panel).
The device vibrates when pairing is completed.
When there is an incoming call:
• The KEY zone illuminates in green color and flashes.
• The unit answers the call automatically if [AUTO ANSWER] is set to a
selected time.
(
24)
During a call:
• The LCD DISPLAY zone illuminates according to the settings made for
[DISPLAY] ( 32) and the KEY zone illuminates in green color.
• If you turn off the unit or detach the faceplate, the Bluetooth
connection is disconnected.
The following operations may differ or not available depending on the
connected phone.
To
On the faceplate
On the remote control
• Depending on the type of remote device used, the strength of the NFC
signal may vary. For a stronger NFC signal, user must understand the
position of the remote device’s NFC antenna and hence tap the NFC
antenna with the NFC logo.
• To disconnect, hold the remote device near to the N-Mark on the unit
again.
First incoming call...
Answer a call
Press
or the
Press
.
volume knob or one of
the number buttons
(1 to 6).
• This unit only can recognize and connect to one NFC-compatible device
at a time.
Reject a call
End a call
Press
Press
.
Press
Press
.
.
.
22
ENGLISH
BLUETOOTH®
Improve the voice quality
To
On the faceplate
On the remote control
While talking on the phone...
While talking on the first incoming call...
1
Press the volume knob to enter [FUNCTION].
Answer another
incoming call and
hold the current call
Press
Press
.
Press
Press
.
2
Turn the volume knob to select an item (see the following table),
then press the knob.
3
4
Repeat step 2 until the desired item is selected or activated.
Press and hold
to exit.
Reject another
incoming call
.
.
.
To return to the previous setting item, press
.
While having two active calls...
Default: XX
(LEVEL –4): The sensitivity of the
End current call and
activate held call
Press
Press
.
Press
MIC GAIN
LEVEL –10 to LEVEL +10
microphone increases as the number increased.
LEVEL –5 to LEVEL +5 LEVEL 0): Adjust the noise reduction level
until the least noise is being heard during a phone conversation.
LEVEL –5 to LEVEL +5 LEVEL 0): Adjust the echo cancellation delay
Swap between the
current call and
held call
Press
.
.
NR LEVEL
(
Adjust the phone
volume
Turn the volume knob
during a call.
Press
or
ECHO CANCEL
(
.
time until the least echo is being heard during a phone conversation.
[00] to [35]
• This adjustment will not affect the volume of
the other sources.
(Default: [15]
)
Make the settings for receiving a call
Switch between
hands-free and
private talk modes
Press
a call.
• Operations may vary
according to the
connected Bluetooth
device.
during
1
2
3
4
Press
to enter Bluetooth mode.
Turn the volume knob to select an item
(
24), then press the knob.
( Not available )
Repeat step 2 until the desired item is selected or activated.
Press and hold to exit.
To return to the previous setting item, press
.
23
ENGLISH
BLUETOOTH®
Default: XX
CALL HISTORY
PHONE BOOK
(Applicable only if the phone supports PBAP.)
1
Press the volume knob to select a name or a phone number.
• “INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part
of the display to indicate the previous call status.
SETTINGS
AUTO ANSWER
1
to 30: The unit answers incoming call automatically in the
selected time (in seconds). ; OFF: Cancels.
• Press DISP to change the display category (NUMBER or NAME).
• “NO DATA” appears if there is no recorded call history.
Press the volume knob to call.
BATTERY/SIGNAL*
AUTO: Shows the strength of the battery and signal when the unit
detects a Bluetooth device and the Bluetooth device is connected. ;
OFF: Cancels.
2
(Applicable only if the phone supports PBAP.)
1
Turn the volume knob quickly to enter alphabet search mode (if the
phonebook contains many contacts).
*
Functionality depends on the type of the phone used.
The first menu (ABCDEFGHIJKLMN) appears.
Make a call
• To go to the other menu (OPQRSTUVWXYZ1 ), press J/ K
.
• To select the desired first letter, turn the volume knob or press
S / T, then press the knob.
You can make a call from the call history, phonebook, or dialing the
number. Call by voice is also possible if your mobile phone has the
feature.
Select “1” to search with numbers and select “ ” to search with
symbols.
2
3
Turn the volume knob to select a name, then press the knob.
Turn the volume knob to select a phone number, then press the knob
to call.
The phonebook of the connected phone is automatically transferred to
the unit when pairing.
Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL.
This unit can display only non-accent letters. (Accent letters such as
“Ú” is shown as “U”.)
1
Press
to enter Bluetooth mode.
“(First device name)” appears.
• If two Bluetooth phones are connected, press
another phone.
again to switch to
•
“(Second device name)” appears.
•
•
2
3
4
Turn the volume knob to select an item (see the following table),
then press the knob.
Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
NUMBER DIAL
1
2
3
Turn the volume knob to select a number (0 to 9) or character
( , #, +).
Press and hold
to exit.
Press S / T to move the entry position.
To return to the previous setting item, press
.
Repeat steps
Press the volume knob to call.
1
and until you finish entering the phone number.
2
(or using the remote control)
1
2
Press the number buttons (
Press to call.
0
to 9) to enter the phone number.
24
ENGLISH
BLUETOOTH®
Make a call from memory
VOICE
Speak the name of the contact you want to call or the voice command to
control the phone functions. Make a call using voice recognition)
(
1
2
3
Press
to enter Bluetooth mode.
Press one of the number buttons (1 to 6).
Press the volume knob to call.
“NO MEMORY” appears if there is no contacts stored.
*
BATTERY LVL LOW/MID/FULL : Shows the strength of the battery.
*
NO SIGNAL/SIGNAL LVL LOW/MID/MAX : Shows the strength of the current received signal.
*
Functionality depends on the type of the phone used.
Other settings
Make a call using voice recognition
1
2
Press the volume knob to enter [FUNCTION].
1
2
Press and hold
connected phone.
to activate the voice recognition of the
Turn the volume knob to select an item (see the following table),
then press the knob.
Speak the name of the contact you want to call or the voice
command to control the phone functions.
3
4
Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
Press and hold
to exit.
• Supported Voice Recognition features vary for each phone. Refer to the
instruction manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of
iPhone.
To return to the previous setting item, press
.
Default: XX
BT MODE
Settings in memory
PHONE SELECT
AUDIO SELECT
DEVICE DELETE
Selects the phone or audio device to connect or disconnect.
Store a contact in memory
“ ” appears in front of the device name when connected.
*
“
•
” appears in front of the current playback audio device.
You can only connect a maximum of two Bluetooth phones and one
Bluetooth audio device at any time.
You can store up to 6 contacts into the number buttons (1 to 6).
1
2
Press
to enter Bluetooth mode.
Turn the volume knob to select [CALL HISTORY] [PHONE BOOK], or
,
[NUMBER DIAL], then press the knob.
1
2
Turn the volume knob to select a device to delete, then press the
knob.
Turn the volume knob to select [YES] or [NO], then press the knob.
3
Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone
number.
PIN CODE EDIT
(0000)
Changes the PIN code (up to 6 digits).
4
Press and hold one of the number buttons (1 to 6).
“STORED” appears when the contact is stored.
1
Turn the volume knob to select a number.
Press to move the entry position.
Repeat steps and until you finish entering the PIN code.
Press the volume knob to confirm.
2
S
/
T
1
2
To erase a contact from the preset memory, select [NUMBER DIAL] in step 2
and store a blank number.
3
25
ENGLISH
BLUETOOTH®
BLUETOOTH — Audio
While in BT AUDIO source, you can connect to five Bluetooth audio
devices and switch between these five devices.
RECONNECT
ON: The unit automatically reconnect when the last connected
Bluetooth device is within range. ; OFF: Cancels.
AUTO PAIRING
ON: The unit automatically pair supported Bluetooth device (iPhone/
iPod touch/Android device) when it is connected through USB input
terminal. Depending on the operating system of the connected device,
this function may not work. ; OFF: Cancels.
INITIALIZE
YES: Initializes all the Bluetooth settings (including stored pairing,
phonebook, and etc.). ; NO: Cancels.
Bluetooth test mode
Audio player via Bluetooth
You can check the connectivity of the supported profile between the
Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1
2
Press
repeatedly (or press SRC on the remote control) to
select BT AUDIO.
Operate the Bluetooth audio player to start playback.
1
2
3
Press and hold
.
To
On the faceplate
On the remote control
“PLEASE PAIR YOUR PHONE PIN 0000” appears.
Playback/pause
Press
.
Press
Press
.
Search and select this unit model name (KDC-X7**/KDC-BT7**HD/
KMR-D7**BT/KDC-X5**/KDC-BT5**U) on the Bluetooth device.
Operate the Bluetooth device to confirm pairing.
“TESTING” flashes on the display.
Select group or
folder
/
.
Press J/ K.
Reverse/Forward
skip
Press S / T.
Press S /
.
The connectivity result (OK or NG) appears after the test.
PAIRING:
HF CONNECT:
AUDIO CONNECT: Advanced Audio Distribution Profile (A2DP)
compatibility
PHONEBOOK DL: Phonebook Access profile (PBAP) compatibility
Pairing status
Hands-Free Profile (HFP) compatibility
Reverse/Fast-
forward
Press and hold
S / T.
Press and hold S /
.
Repeat play
Press
repeatedly.
( Not available )
( Not available )
ALL REPEAT FILE REPEAT,
,
REPEAT OFF
To cancel test mode, press and hold
to turn off the unit.
Random play
Press and hold
select ALL RANDOM
to
.
• Press
to select
RANDOM OFF
.
26
ENGLISH
BLUETOOTH®
Default: XX
To
On the faceplate
On the remote control
REMOTE APP
SELECT
Select a file from a
folder/list
Refer to “Select a file
from a folder/list” on
page 11.
( Not available )
Select the device (IOS or ANDROID) to use the application.
IOS
YES: Selects iPhone/iPod to use the application via Bluetooth or
connected via USB input terminal. ; NO: Cancels.
If IOS is selected, select iPod BT source (or iPod 1/iPod 2/iPod USB if
your iPhone/iPod is connected via USB input terminal) to activate the
application.
Switch between
connected
Bluetooth audio
devices
Press 5.*
( Not available )
•
The connectivity of the application will be interrupted or disconnected
if:
– You change from iPod BT source to any playback source connected
via the USB input terminal.
*
Pressing the “Play” key on the connected device itself also causes switching of sound output
from the device.
Operations and display indications may differ according to their
availability on the connected device.
– You change from iPod 1/iPod 2/iPod USB source to iPod BT source.
ANDROID
YES: Selects Android smartphone to use the application via Bluetooth. ;
NO: Cancels.
Settings to use KENWOOD Remote application
ANDROID LIST
STATUS
*
Selects the Android smartphone to use from the list.
KENWOOD Remote application is designed to control the KENWOOD
car receiver’s operations from the iPhone/iPod (via Bluetooth or via USB
input terminal) or Android smartphone (via Bluetooth).
Shows the status of the selected device.
IOS CONNECTED: You are able to use the application using the iPhone/
iPod connected via Bluetooth or USB input terminal.
IOS NOT CONNECTED: No IOS device is connected to use the application.
ANDROID CONNECTED: You are able to use the application using the
Android smartphone connected via Bluetooth.
ANDROID NOT CONNECTED: No Android device is connected to use the
application.
Preparation:
Install the latest version of KENWOOD Remote application on your device
before connecting. For more information, visit
<www.kenwood.com/cs/ce/>.
*
Displayed only when [ANDROID] of [SELECT] is set to [YES].
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table),
then press the knob.
3
4
Repeat step
2
until the desired item is selected or activated.
to exit.
Press and hold
To return to the previous setting item, press
.
27
ENGLISH
BLUETOOTH®
Listen to iPhone/iPod via Bluetooth
You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.
Listen to iHeartRadio
Preparation:
Select [ON] for [IHEART SRC] in [SOURCE SELECT]
.
(
5)
Press
• You can operate the iPod/iPhone in the same way as iPod/iPhone via
USB input terminal.
repeatedly to select iPod BT.
1
2
3
Open the iHeartAuto application on your device.
Connect your device via Bluetooth connection.
Press repeatedly to select IHEARTRADIO.
The source switches and broadcast starts automatically.
(
21)
(
10)
• If you plug in an iPhone/iPod to the USB input terminal while listening
to iPod BT source, the source automatically change to iPod 1/iPod 2/
iPod USB. Press
via Bluetooth.
to select iPod BT if the device is still connected
• You can operate iHeartRadio in the same way as iHeartRadio via USB
input terminal.
(
15)
Listen to Spotify
Preparation:
Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]
Internet radio via Bluetooth
You can listen to internet radio (Pandora, iHeartRadio and Spotify) on the
iPhone/iPod/Android device via Bluetooth on this unit.
• Make sure the USB input terminal is not connected to any device.
.
(
5)
1
2
3
Open the Spotify application on your device.
Connect your device via Bluetooth connection.
(
21)
Press
repeatedly to select SPOTIFY (for iPhone/iPod) or
Listen to Pandora
Preparation:
Select [ON] for [PANDORA SRC] in [SOURCE SELECT]
SPOTIFY BT (for Android device).
The source switches and broadcast starts automatically.
.
(
5)
• You can operate Spotify in the same way as Spotify via USB input
terminal.
1
2
3
Open the Pandora application on your device.
Connect your device via Bluetooth connection.
(
16)
(
21)
Press
repeatedly to select PANDORA (for iPhone/iPod) or
PANDORA BT (for Android device).
The source switches and broadcast starts automatically.
• You can operate Pandora in the same way as Pandora via USB input
terminal.
(
13)
28
ENGLISH
AUDIO SETTINGS
While listening to any source...
PRESET EQ
NATURAL/ROCK/POPS/EASY/TOP40/JAZZ/POWERFUL/USER:
Selects a preset equalizer suitable to the music genre. (Select [USER]
to use the settings made in [MANUAL EQ].)
1
2
Press AUDIO to enter [AUDIO CONTROL] directly.
Turn the volume knob to select an item (see the following table),
then press the knob.
BASS BOOST
LOUDNESS
LEVEL1/LEVEL2/LEVEL3/LEVEL4/LEVEL5: Selects your preferred
3
4
Repeat step 2 until the desired item is selected or activated.
bass boost level. ; OFF: Cancels.
Press and hold
to exit.
LEVEL1 LEVEL2: Selects your preferred low and high frequencies
/
(or using the remote control)
boost to produce a well-balanced sound at a low volume level. ;
OFF: Cancels.
1
Press AUD to enter [AUDIO CONTROL].
2
Press J/ K to select an item, then press
.
SUBWOOFER SET
FADER
ON: Turns on the subwoofer output. ; OFF: Cancels.
REAR 15 to FRONT15
balance.
(
0
): Adjusts the rear and front speaker output
): Adjusts the left and right speaker output
LEVEL 0): Preset the initial volume level
To return to the previous setting item, press
.
BALANCE
LEFT 15 to RIGHT15
balance.
(0
Default: XX
AUDIO CONTROL
VOLUME OFFSET
LEVEL –15 to LEVEL +6
of each source. (Before adjustment, select the source you want to
adjust.)
(
SUB-W LEVEL
MANUAL EQ
62.5HZ LEVEL
LEVEL –50 to LEVEL +10 (LEVEL 0): Adjusts the subwoofer
output level.
The sound elements (frequency level, tone level, Q factor) are
preset into each selection.
SOUND EFFECT
SOUND RECONSTRA (Not applicable for RADIO source, AUX source and SIRIUS XM source.)
LEVEL
LEVEL –9 to LEVEL +9 (LEVEL 0): Adjusts
(Sound
reconstruction)
ON: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are
lost in audio data compression. ; OFF: Cancels.
the level to memorize for each source.
(Before making an adjustment, select the
source you want to adjust.)
SPACE ENHANCER (Not applicable for RADIO source.)
SMALL MEDIUM LARGE: Virtually enhances the sound space. ;
OFF: Cancels.
BASS EXTEND ON: Turns on the extended bass. ;
/
/
OFF: Cancels.
LEVEL –9 to LEVEL +9 (LEVEL 0): Adjusts the level to
memorize for each source. (Before making an adjustment,
select the source you want to adjust.)
100 HZ/160 HZ/250 HZ/
400 HZ/630 HZ/1 KHZ/
1.6KHZ/2.5KHZ/4 KHZ/
6.3KHZ/10 KHZ/16 KHZ
LEVEL
SOUND REALIZER LEVEL1/LEVEL2
/LEVEL3: Virtually makes the sound more realistic. ;
OFF: Cancels.
STAGE EQ
DRIVE EQ
LOW
/
MIDDLE
/
HIGH: Virtually adjust the sound position heard from
the speakers. ; OFF: Cancels.
ON: Boosts the frequency to reduce the noise heard from outside the
Q FACTOR
1.35/1.50/2.00: Adjust the quality factor.
car or running noise of the tyres. ; OFF: Cancels.
29
ENGLISH
AUDIO SETTINGS
SPEAKER SIZE
FRONT
The frequency and slope settings are automatically set for the crossover of
the selected speaker.
REAR HPF
REAR - HPF FRQ
REAR - HPF SLOPE (Refer FRONT HPF settings.)
REAR - HPF GAIN
SIZE
3.5"
6×9
size for optimum performance.
/
/
4"
/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/
7×10: Selects according to the connected speaker
SUBWOOFER SW LPF FRQ
LPF
30HZ
100HZ
/
40HZ
/
50HZ
/
60HZ
/
70HZ
/
80HZ
/
/
90HZ
250HZ:
/
/120HZ
/
150HZ
/180HZ
/
220HZ
TWEETER
SMALL MIDDLE LARGE: Selects according to the
/
/
Adjusts the crossover frequency for the subwoofer
(low pass filter). ; THROUGH: All signals are sent to
the subwoofer.
size range of the connected tweeter for optimum
performance. ; NONE: Not connected.
REAR
3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/7×10:
Selects according to the connected speaker size for optimum
performance. ; NONE: Not connected.
SW LPF SLOPE
SW LPF PHASE
–6DB
crossover slope.
(Selectable only if a setting other than [THROUGH] is
selected for [SW LPF FRQ].)
/–12DB/–18DB/–24DB: Adjusts the
SUBWOOFER 6.5"
/8"
/10"/12"/15" OVER: Selects according to the connected speaker
size for optimum performance. ; NONE: Not connected.
REVERSE (180°)/NORMAL (0°): Selects the phase
of the subwoofer output to be in line with the
speaker output for optimum performance.
X ' OVER
TWEETER
FRQ
1KHZ
10KHZ
the tweeter speaker.
/
1.6KHZ
/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ/
/12.5KHZ: Adjusts the crossover frequency for
SW LPF GAIN
DTA SETTINGS
–8 to
0: Adjusts the output volume of the
subwoofer.
GAIN LEFT
–8 to
0
: Adjusts the output volume of the left tweeter.
: Adjusts the output volume of the right tweeter.
For settings, 31, Digital Time Alignment settings
.
GAIN RIGHT –8 to
0
CAR SETTINGS
FRONT HPF
FRONT - HPF 30HZ
/
40HZ
150HZ
crossover frequency for the selected speakers (high
pass filter). THROUGH: All signals are sent to the
selected speakers.
/
50HZ
/
60HZ
/
70HZ
/
80HZ
/
90HZ
/
100HZ
/
•
The following item is selectable only if [SUBWOOFER SET] is set to [ON] ( 29):
FRQ
120HZ
/
/
180HZ
/220HZ
/250HZ: Adjusts the
–
–
–
–
[SUB-W LEVEL]
[SUBWOOFER] of [SPEAKER SIZE]
[SUBWOOFER LPF] of [X ’ OVER]
[SUBWOOFER] of [DISTANCE] and [GAIN] in [DTA SETTINGS]
;
•
The following item is selectable only if a setting other than [NONE] is selected for
[TWEETER] [REAR] and [SUBWOOFER] of [SPEAKER SIZE]
[TWEETER] [REAR HPF] [SUBWOOFER LPF] of [X ’ OVER]
FRONT - HPF –6DB –12DB –18DB
SLOPE slope.
/
/
/
–24DB: Adjusts the crossover
,
:
–
,
,
(Selectable only if a setting other than [THROUGH] is
selected for [FRONT - HPF FRQ].)
FRONT - HPF –8 to
0: Adjusts the output volume of the selected
GAIN speaker.
30
ENGLISH
AUDIO SETTINGS
•
•
Before making an adjustment for [DISTANCE] and [GAIN] of [DTA SETTINGS], select the
speaker you want to adjust:
Digital Time Alignment settings
FRONT LEFT
You can only select [REAR LEFT], [REAR RIGHT] and [SUBWOOFER] if a setting other than
[NONE] is selected for [REAR] and [SUBWOOFER] of [SPEAKER SIZE] 30)
[REAR - SP LOCATION] of [CAR SETTINGS] is selectable only if a setting other than [NONE]
is selected for [REAR] of [SPEAKER SIZE] 30)
/FRONT RIGHT/REAR LEFT/REAR RIGHT/SUBWOOFER:
Digital Time Alignment sets the delay time of the speaker output to
create a more suitable environment for your vehicle.
.
(
• For more information, Determining the value for [DISTANCE] and [GAIN] of
[DTA SETTINGS]
.
.
(
Default: XX
Determining the value for [DISTANCE] and [GAIN] of [DTA SETTINGS]
DTA SETTINGS
POSITION
Selects your listening position (reference point).
ALL: Not compensating ; FRONT RIGHT: Front right seat ;
FRONT LEFT: Front left seat ; FRONT ALL: Front seat
DISTANCE
GAIN
0FT to 20.01FT: Fine adjust the distance to compensate. (Before
making an adjustment, select the speaker you want to adjust.)
–8DB to 0DB: Fine adjust the output volume of the selected speaker.
(Before making an adjustment, select the speaker you want to adjust.)
DTA RESET
CAR SETTINGS
CAR TYPE
YES: Resets the settings ([DISTANCE] and [GAIN]) of the selected
[POSITION] to default. ; NO: Cancels.
Identify your car type and rear speaker location in order to make the
adjustment for [DTA SETTINGS]
.
COMPACT FULL SIZE CAR WAGON/MINIVAN/SUV/
/
/
If you specify the distance from the center of the currently set listening position to every
speaker, the delay time will be automatically computed and set.
MINIVAN(LONG): Selects the type of vehicle. ; OFF: Not compensating.
1
2
3
Determine the center of the currently set listening position as the reference point.
Measure the distances from the reference point to the speakers.
Calculate the differences between the distance of the furthest speaker (rear speaker) and
other speakers.
REAR - SP
LOCATION
Selects the location of the rear speakers in your vehicle to calculate the
furthest distance from the listening position selected (reference point).
•
DOOR
[OFF]
2ND ROW
as [MINIVAN] or [MINIVAN(LONG)]
/
,
REAR DECK: Selectable only when [CAR TYPE] is selected as
[COMPACT] [FULL SIZE CAR] [WAGON] or [SUV]
3RD ROW: Selectable only when [CAR TYPE] is selected
,
,
.
4
5
Set the [DISTANCE] calculated in step for individual speakers.
3
•
/
Adjust [GAIN] for individual speakers.
.
Example: When [FRONT ALL] is selected as the listening position
31
ENGLISH
DISPLAY SETTINGS
Zone identification for color and brightness settings
Default: XX
DISPLAY
COLOR
SELECT
Select color for ALL ZONE
,
LCD DISPLAY and KEY separately.
Select a zone. (See the illustration on the left column.)
Select a color for the selected zone.
1
2
INITIAL COLOR
/VARIABLE SCAN/CUSTOM R/G/B/preset colors*
Default:
/
/
/
: VARIABLE SCAN
INITIAL COLOR
:
To make your own color, select [CUSTOM R/G/B]. The color you have made
will be stored in [CUSTOM R/G/B]
Set the dimmer
.
Press and hold DISP (DIM) to turn on or off the dimmer.
• If you have set [DIMMER TIME], it will be canceled once you press and
hold this button.
1
2
3
Press the volume knob to enter the detailed color adjustment.
Press to select the color ( ) to adjust.
Turn the volume knob to adjust the level ( to ), then press the knob.
S
/
T
R/G/B
0
9
DIMMER
Dim the illumination.
ON: Dimmer is turned on. ; OFF: Cancels.
DIMMER TIME: Set the dimmer on and off time.
Other settings
1
2
Press the volume knob to enter [FUNCTION].
1
Turn the volume knob to adjust the [ON] time, then press the knob.
Turn the volume knob to adjust the [OFF] time, then press the knob.
Turn the volume knob to select an item (see the following table)
,
2
then press the knob.
(Default: [ON]
:
PM6:00
;
[OFF]: AM6:00)
3
4
Repeat step 2 until the desired item is selected/activated or follow
BRIGHTNESS
1
2
Select a zone. (See the illustration on the left column.)
LEVEL 0 to LEVEL 31: Select your preferred brightness level for the
selected zone.
the instructions stated on the selected item.
Press and hold
to exit.
To return to the previous setting item, press
.
TEXT SCROLL AUTO
/ONCE: Select whether to scroll the display information automatically,
or scroll only once. ; OFF: Cancels.
*
Preset colors: RED1 RED2 RED3 PURPLE1 PURPLE2
/
/
/
/
/
PURPLE3
/
PURPLE4
/
BLUE1
/
/
BLUE2 BLUE3 SKYBLUE1 SKYBLUE2 LIGHTBLUE AQUA1
GREEN2 GREEN3 YELLOWGREEN1 YELLOWGREEN2 YELLOW
ORANGERED
/
/
/
/
/
/
AQUA2
/GREEN1
/
/
/
/
/
ORANGE1/ORANGE2/
32
ENGLISH
TROUBLESHOOTING
Symptom
Sound cannot be heard.
Remedy
Symptom
Elapsed playing time is not
Remedy
•
•
Adjust the volume to the optimum level.
Check the cords and connections.
This is caused by how the tracks are recorded.
correct.
“MISWIRING CHECK WIRING
THEN POWER ON” appears.
Turn the power off, then check to be sure the
terminals of the speaker wires are insulated properly.
Turn the power on again.
“LOADING” appears when
you enter search mode by
This unit is still preparing the iPod/iPhone music list. It
may take some time to load, try again later.
pressing
.
“PROTECTING SEND TO
SERVICE” appears.
Send the unit to the nearest service center.
Correct characters are not
displayed (e.g. album name).
•
•
This unit can only display uppercase letters,
numbers, and a limited number of symbols.
Depending on the display language you have
•
•
•
Sound cannot be heard.
The unit does not turn on.
Information shown on the
display is incorrect.
Clean the connectors.
(
36)
selected
(
5), some characters may not be
displayed correctly.
“NA FILE”
Make sure the media contains supported audio files.
37)
(
The unit does not work at all. Reset the unit.
(
3)
“NO DISC”
Insert a playable disc into the loading slot.
Setting/deleting the remote control ID is
unsuccessful. Turn the power off, then turn on the
(For
)
“TOC ERROR”
“PLEASE EJECT”
Make sure the disc is clean and inserted properly.
“SET ERROR”/
“DELETE ERROR”
power and perform the operation again.
(
6)
Reset the unit. If this does not solve the problem,
consult your nearest service centre.
•
•
Radio reception is poor.
Static noise while listening
to the radio.
Connect the antenna firmly.
“NO DEVICE”
Connect a USB device, and change the source to USB
again.
“COPY PROTECTED”
A copy-protected file is played.
“UNSUPPORTED DEVICE”
•
Check whether the connected device is compatible
with this unit and ensure the file systems are in
Disc cannot be ejected.
Press and hold
not to drop the disc when it is ejected. If this does not
solve the problem, reset the unit. 3)
M
to forcibly eject the disc. Be careful
supported formats.
(
37)
(
•
Reattach the device.
Noise is generated.
Skip to another track or change the disc.
“UNRESPONSIVE DEVICE”
Make sure the device is not malfunction and reattach
the device.
Tracks do not play back as
you intended them to play.
Playback order is determined when files are
recorded.
“USB HUB IS NOT
SUPPORTED”
This unit cannot support a USB device connected via
a USB hub.
“READING” keeps flashing.
Do not use too many hierarchical levels or folders.
33
ENGLISH
TROUBLESHOOTING
Symptom
Remedy
Symptom
Remedy
•
The source does not
change to “USB” when
you connect a USB
device while listening to problem, turn the power off and on (or reset the unit) before
another source.
The USB port is drawing more power than the design limit. Turn
the power off and unplug the USB device. Then, turn on the
power and reattach the USB device. If this does not solve the
Playback is intermittent Turn off the power saving mode on the Android
or sound skips.
device.
“ANDROID ERROR”/
“NA DEVICE”
•
•
Reconnect the Android device.
Restart the Android device.
replacing with another USB device.
“ADD ERROR”
“CHECK DEVICE”
“NO SKIPS”
New station creation is unsuccessful.
Check the Pandora application on your device.
The skip limit has been reached.
No stations are found.
•
“USB ERROR” appears.
“NO MUSIC”
Connect a USB device that contains playable audio files.
“iPod ERROR”
•
•
Reconnect the iPod.
Reset the iPod.
“NO STATIONS”
“STATION LIMIT”
•
•
Sound cannot be heard
during playback.
Sound output only from
the Android device.
•
•
Reconnect the Android device.
If in [HAND MODE], launch any media player application on
the Android device and start playback.
The number of registered stations has reached its
limit. Retry after deleting unnecessary stations
from your device.
•
If in [HAND MODE], relaunch the current media player
application or use another media player application.
Restart the Android device.
“CONNECT ERROR”
“RATING ERROR”
Communication is unstable.
•
•
Registration of thumbs up/thumbs down has failed
due to insufficient network connectivity.
If this does not solve the problem, the connected Android
device is unable to route the audio signal to unit.
Make sure KENWOOD MUSIC PLAY APP is installed on the
Android device. 10)
(
37)
“THUMBS N/A”
Registration of thumbs up/thumbs down is not
allowed.
Cannot playback at
[BROWSE MODE]
•
•
•
.
(
“LICENSE ERROR”
You try to access from a country which Pandora is
not deliverable.
Reconnect the Android device and select the appropriate
control mode.
If this does not solve the problem, the connected Android
iHeartRadio station
cannot be selected.
If “Explicit Content” in [Account Settings] is checked
in the web version of iHeartRADIO, custom stations
become unavailable.
device does not support [BROWSE MODE]
.
(
37)
“NO DEVICE” or “READING”
keeps flashing.
•
•
•
Switch off the developer options on the Android device.
Reconnect the Android device.
If this does not solve the problem, the connected Android
“NOT CONNECTED”
Link to the application is impossible.
device does not support [BROWSE MODE]
.
(
37)
34
ENGLISH
TROUBLESHOOTING
Symptom
“DISCONNECTED”
Remedy
Symptom
No Bluetooth device is
Remedy
USB is disconnected from the head unit. Please make sure
the device is connected properly through USB.
•
•
Search from the Bluetooth device again.
Reset the unit. 3)
detected.
(
“CONNECTING”
“CHECK APP”
•
Connected via USB input terminal: The device is
connecting to the head unit. Please wait.
Connected via Bluetooth: The Bluetooth is disconnected.
Please check Bluetooth connection and make sure both
the device and the unit are paired and connected.
Bluetooth pairing cannot
be made.
•
Make sure you have entered the same PIN code to both
the unit and Bluetooth device.
Delete pairing information from both the unit and the
•
•
Bluetooth device, then perform pairing again.
Adjust the microphone unit’s position. 20)
Check the [ECHO CANCEL] setting. 23)
(
21)
Echo or noise is heard
during a phone
conversation.
•
•
(
The Spotify application is not connected properly, or user is
not login. End the Spotify application and restart, then login
to your Spotify account.
(
Phone sound quality is
poor.
•
•
Reduce the distance between the unit and the
Bluetooth device.
Move the car to a place where you can get a better
signal reception.
“CHAN LOCKED ENTER
CODE:”
The selected channel is locked. Enter the correct pass code to
unlock.
The selected channel is unsubscribed. Call 1-866-635-2349 in
the U.S.A. or 1-877-438-9677 in Canada to subscribe. 17)
(
19)
“CH UNSUBSCRIBED”
(
Voice calling method is not
successful.
•
•
Use voice calling method in a more quiet environment.
Reduce the distance from the microphone when you
speak the name.
Make sure the same voice as the registered voice tag is
used.
for more information about the SiriusXM channel lineup.
•
•
“CHECK ANTENNA”
“CHECK TUNER”
“NO SIGNAL”
Check that the antenna and its connection are in good
condition.
Sound is being interrupted
or skipped during playback
of a Bluetooth audio
player.
Reduce the distance between the unit and the
Bluetooth audio player.
Turn off, then turn on the unit and try to connect again.
Other Bluetooth devices might be trying to connect to
the unit.
Make sure the SiriusXM Vehicle Tuner is connected to the
unit.
•
•
Make sure the antenna is mounted outside the vehicle.
“SUBSCRIPTION
UPDATED – PRESS
ENTER TO CONTINUE.”
Your subscription is updated. Press the volume knob to
continue.
The connected Bluetooth
audio player cannot be
controlled.
•
•
Check whether the connected Bluetooth audio player
supports Audio/Video Remote Control Profile (AVRCP).
(Refer to the instructions of your audio player.)
“CODE ERROR”
“NO CONTENT”
“SCAN CANCEL”
Make sure you have entered the correct pass code.
There is insufficient content to start TuneScan.
TuneScan has been aborted.
(
19)
Disconnect and connect the Bluetooth player again.
35
ENGLISH
TROUBLESHOOTING
REFERENCES
Maintenance
Cleaning the unit
Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Symptom
“DEVICE FULL”
Remedy
The number of registered devices has reached its limit.
Retry after deleting an unnecessary device.
(
25,
DEVICE DELETE)
Cleaning the connector
“N/A VOICE TAG”
“NOT SUPPORT”
Make sure the same voice as the registered voice tag is used.
Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to
damage the connector.
The connected phone does not support Voice Recognition
feature or phonebook transfer.
Connector (on the reverse
side of the faceplate)
“NO ENTRY”/“NO PAIR” There is no registered device connected/found via Bluetooth.
Handling discs
“ERROR”
Try the operation again. If “ERROR” appears again, check if
the device supports the function you have tried.
•
•
•
•
•
•
•
Do not touch the recording surface of the disc.
Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
Do not use any accessories for the disc.
“NO INFO”/“NO DATA”
Bluetooth device cannot get the contact information.
Clean from the center of the disc and move outward.
“HF ERROR XX”/
“BT ERROR”
Reset the unit and try the operation again. If this does not
solve the problem, consult your nearest service center.
Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
When removing discs from this unit, pull them out horizontally.
Remove burrs from the center hole and disc edge before inserting a disc.
“SWITCHING NG”
The connected phones might not support phone switching
feature.
More information
For: – Latest firmware updates and latest compatible item list
– KENWOOD original application
– Any other latest information
Visit <www.kenwood.com/cs/ce/>.
General
•
This unit can only play the following CDs:
•
For detailed information and notes about the playable audio files, visit
<www.kenwood.com/cs/ce/audiofile/>.
36
ENGLISH
REFERENCES
Playable files
About Android device
• This unit supports Android OS 4.1 and above.
•
Playable audio file:
For disc: MP3 (.mp3), WMA (.wma), AAC (.aac)
• Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory
For USB mass storage class device: MP3 (.mp3), WMA (.wma), AAC (.aac), AAC (.m4a),
WAV (.wav), FLAC (.flac)
Playable disc media: CD-R/CD-RW/CD-ROM
Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.
Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible
depending on the types or conditions of media or device.
The AAC (.m4a) file in a CD encoded by iTunes cannot be played on this unit.
(AOA) 2.0.
•
If the Android device supports both mass storage class device and AOA 2.0, this unit always
playback via AOA 2.0 as priority.
•
•
•
About Pandora
•
Pandora is only available in certain countries.
For more information, visit <http://www.pandora.com/legal>.
Because Pandora is a third-party service, the specifications are subject to change without
prior notice. Accordingly, compatibility may be impaired, or some or all of the services may
become unavailable.
•
Unplayable discs
•
•
•
•
Discs that are not round.
•
•
Some functions of Pandora cannot be operated from this unit.
For issues using the application, please contact Pandora at [email protected].
Discs with coloring on the recording surface or discs that are dirty.
Recordable/ReWritable discs that have not been finalized.
8 cm CD. Attempting to insert using an adapter may cause malfunction.
About iHeartRadio
•
iHeartRadio® is a third-party service, therefore the specifications are subject to change
without prior notice. Accordingly, compatibility may be impaired or some or all of the
services may become unavailable.
About USB devices
•
•
•
You cannot connect a USB device via a USB hub.
Connecting a cable whose total length is longer than 5 m may result in abnormal playback.
This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1.5 A.
•
Some iHeartRadio® functionality cannot be operated from this unit.
About Spotify
About iPod/iPhone
•
Spotify application supports:
– iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus (iOS 8 or above)
– iPod touch (5th and 6th generation)
•
Via USB:
Made for
– iPod touch (5th and 6th generation)
– iPod nano (7th generation)
– iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus
Via Bluetooth:
– Android OS 4.0.3 or above
•
Spotify is a third-party service, therefore the specifications are subject to change without
prior notice. Accordingly, compatibility may be impaired or some or all of the services may
become unavailable.
•
Made for
•
•
Some functions of Spotify cannot be operated from this unit.
For issues using the application, please contact Spotify at <www.spotify.com>.
– iPod touch (5th and 6th generation)
– iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus
You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.
Depending on the version of the operating system of the iPod/iPhone, some functions may
not operate on this unit.
•
•
37
ENGLISH
REFERENCES
About Bluetooth
Change the display information
•
Depending on the Bluetooth version of the device, some Bluetooth devices may not be able
to connect to this unit.
Each time you press DISP, the display information changes.
•
If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information
(eg. station name, playing time) appears.
•
•
•
This unit may not work with some Bluetooth devices.
Signal conditions vary, depending on the surroundings.
/
/
:
Source name
Display information
Compatible remote device for NFC function:
Remote devices with a NFC function (OS: Android™ 2.3.3 or later, excluding Android 3.x).
If the OS version of your remote device is older than Android 4.1.x, download and start the
“NFC Easy Connect” application. (“NFC Easy Connect” is a free application available at Google
Play.)
STANDBY
HD RADIO
Source name (Date)*
(For
/
)
(For digital stations only)
Station name (Date)* Song title (Artist) Song title (Album title)
Song title (Date)* Frequency (Date)* (back to the beginning)
About HD Radio™ Technology
(For FM Radio Broadcast Data System stations only)
Station name (Date)* Radio text+ (R.TEXT+/Artist) Radio text+
(R.TEXT+/Album title) Song title (Date)* Frequency (Date)*
(back to the beginning)
•
Adjacent to traditional main stations are extra local FM channels.
These HD2/HD3 Channels provide new, original music as well as
deep cuts into traditional genre.
•
Digital, CD-quality sound. HD Radio Technology enables local radio
stations to broadcast a clean digital signal. AM sounds like today’s
FM and FM sounds like a CD.
RADIO
(For
Frequency (Date)*
/
/
)
•
•
Program Info provides song name, artist, station ID, and other
relevant data to enrich the listening experience.
(For FM Radio Broadcast Data System stations only)
Station name (Date)* Radio text (Date)* Radio text+ (R.TEXT+)
Song title (Artist) Song title (Date)* Frequency (Date)*
(back to the beginning)
Emergency Alert delivers critical and life-saving messages to the
public during emergency situations.
CD or USB 1/
USB 2/USB
(For CD-DA)
Track title (Artist) Track title (Disc name) Track title (Date)*
Playing time (Date)* (back to the beginning)
(For MP3/WMA/AAC/WAV/FLAC files)
Song title (Artist) Song title (Album title) Song title (Date)*
File name (Folder name) File name (Date)* Playing time (Date)*
(back to the beginning)
:
*
(
39)
38
ENGLISH
REFERENCES
INSTALLATION/CONNECTION
Warning
Source name
Display information
•
•
•
The unit can only be used with a 12 V DC power supply, negative ground.
Disconnect the battery’s negative terminal before wiring and mounting.
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
iPod 1/iPod 2/iPod USB/ When [MODE OFF]
iPod BT or ANDROID 1/
ANDROID 2/ANDROID
/
[BROWSE MODE] is selected
Song title (Artist) Song title (Album name) Song title (Date)*
Playing time (Date)* (back to the beginning)
(
11):
•
To prevent short-circuit:
– Insulate unconnected wires with vinyl tape.
PANDORA 1/
Station name (Date)* Shared/Radio station (Date)* Song title
PANDORA 2/PANDORA/ (Artist) Song title (Album title) Song title (Date)*
– Be sure to ground this unit to the car’s chassis again after installation.
– Secure the wires with cable clamps and wrap vinyl tape around the wires that come into
contact with metal parts to protect the wires.
PANDORA BT
Playing time (Date)* (back to the beginning)
IHEARTRADIO 1/
IHEARTRADIO 2/
IHEARTRADIO
Station name (Date)* Song title (Artist) Song title (Date)*
(back to the beginning)
Caution
•
•
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
SPOTIFY 1/SPOTIFY 2/
SPOTIFY/SPOTIFY BT
Context title (Date)* Song title (Artist) Song title
(Album name) Song title (Date)* Playing time (Date)*
(back to the beginning)
•
Do not connect the
them in parallel.
[
wires of speakers to the car chassis or Ground wire (black), or connect
SIRIUS XM
Channel number (Status) Channel name (Status)
Artist name (Status) Song title (Status) Content information
(Status) Category name (Status) Date (Status)
(back to the beginning)
•
•
Mount the unit at an angle of less than 30º.
If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned
on and off by the ignition key.
Keep all cables away from heat dissipate metal parts.
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
BT AUDIO
AUX
Song title (Artist) Song title (Album name) Song title (Date)*
Playing time (Date)* (back to the beginning)
•
•
Source name (Date)*
•
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old
fuse with one that has the same rating.
*
Battery and signal strength of the Bluetooth device will be shown if [BATTERY/SIGNAL] is
set to [AUTO] 24)
.
(
39
ENGLISH
INSTALLATION/CONNECTION
Part list for installation
Installing the unit (in-dash mounting)
(A) Faceplate
(B) Trim plate
Do the required wiring.
41)
(
Hook on the top side
(C) Mounting sleeve
(D) Wiring harness
Orientate the trim plate
as illustrated before
fitting.
Dashboard of
your car
Bend the appropriate tabs to hold the
mounting sleeve firmly in place.
(E) Extraction key
(F) Screws (supplied for
/
)
When installing without the mounting
sleeve
How to remove the unit
1
2
Detach the faceplate.
Fit the catch pin on the extraction keys into
the holes on both sides of the trim plate, then
pull it out.
1
Remove the mounting sleeve and trim plate from
the unit.
2
Align the holes in the unit (on both sides) with
the vehicle mounting bracket and secure the unit
with screws (supplied/commercially available).
3
Insert the extraction keys deeply into the slots
on each side, then follow the arrows as shown
on the illustration.
Basic procedure
1
2
3
Remove the key from the ignition switch, then disconnect the
Use only the specified screws. Using wrong screws
[
terminal of the car battery.
Connect the wires properly.
See Wiring connection. 41)
Install the unit to your car.
See Installing the unit (in-dash mounting).
might damage the unit.
(
4
5
6
Connect the
Press
[
terminal of the car battery.
to turn on the power.
Detach the faceplate and reset the unit within 5 seconds.
(
3)
40
ENGLISH
INSTALLATION/CONNECTION
Wiring connection
IMPORTANT : We recommend installing the unit with a commercially
available custom wiring harness specific for your car and leave this job to
professionals for your safety. Consult your car audio dealer.
Antenna terminal
When connecting to an external amplifier, connect its ground wire to the
car’s chassis to avoid damaging the unit.
Fuse (10 A)
White
White/Black
Gray
If no connections are made, do not let the wire come out from the tab.
To connect the Kenwood navigation system, refer your
To front speaker (left)
Brown
To front speaker (right)
To rear speaker (left)
Gray/Black
navigation manual
(Mute control wire)
Green
Green/Black
Purple
To the power control terminal when using the optional
power amplifier or to the antenna control terminal in
the vehicle
Blue/White
To rear speaker (right)
Purple/Black
(Power control wire/
Antenna control wire)
(12 V
350 mA)
Ignition switch
Car fuse box
Red (Ignition wire)
Yellow (Battery wire)
(For
/
/
/
)
To the steering wheel remote control adapter
(For
To Kenwood Marine Remote Control unit (optional
accessory)
For the latest information on marine accessories, visit
<http://www.kenwood.com/usa/car/marine/>
Light blue/yellow
)
Car fuse box
(Steering remote control
wire)
Black (Ground wire)
To the metallic body or chassis of the car
Battery
41
ENGLISH
INSTALLATION/CONNECTION
Connecting external components
MIC (Microphone input terminal)
(
20)
(For
)
To Kenwood Marine Remote Control unit, KCA-RC55MR (optional accessory)
(
6)
(For
/
/
)
USB 2 cable (DC 5 V 1.5 A)
USB 1 cable (DC 5 V 1.5 A)
Output terminals
Auxiliary cable
Expansion port (12 V 500 mA)
To the optional SiriusXM Vehicle Tuner
(commercially available)
(
17)
42
ENGLISH
SPECIFICATIONS
FM Frequency Range
Usable Sensitivity
87.9 MHz — 107.9 MHz (200 kHz space)
Laser Diode
GaAIAs
7.2 dBf (0.63 μV/75 Ω)
(S/N = 30 dB, Dev 22.5 kHz)
Digital Filter (D/A)
Spindle Speed
8 times over sampling
500 rpm — 200 rpm (CLV)
Below measurable limit
20 Hz — 20 kHz
Quieting Sensitivity
15.2 dBf (1.58 μV/75 Ω)
(DIN S/N = 46 dB, Dev 40 kHz)
Wow & Flutter
Frequency Response ( 1 dB)
Frequency Response
( 3 dB)
HD Radio Broadcast:
20 Hz — 20 kHz
Total Harmonic Distortion (1 kHz) 0.01 %
Signal-to-Noise Ratio (1 kHz)
Conventional Broadcast: 30 Hz — 15 kHz
/
: 110 dB
Signal-to-Noise Ratio
HD Radio Broadcast: 75 dB (STEREO)
Conventional Broadcast: 68 dB (MONO)
/
/
: 105 dB
Stereo Separation (1 kHz)
AM Frequency Range
40 dB
Dynamic Range
Channel Separation
MP3 Decode
90 dB
85 dB
530 kHz — 1 700 kHz (10 kHz space)
29 dBμ (28.2 μV)
Usable Sensitivity
(S/N = 20 dB)
Compliant with MPEG-1/2 Audio Layer-3
Compliant with Windows Media Audio
AAC-LC “.aac” files
WMA Decode
AAC Decode
Frequency Response
( 3 dB)
HD Radio Broadcast:
HD Radio Broadcast:
40 Hz — 15 kHz
70 dB (STEREO)
Signal-to-Noise Ratio
USB Standard
File System
USB 1.1/USB 2.0 Full Speed
FAT12/16/32
FM Frequency Range
Usable Sensitivity
87.9 MHz — 107.9 MHz (200 kHz space)
8.2 dBf (0.71 μV/75 Ω) (S/N = 26 dB)
17.2 dBf (2.0 μV/75 Ω) (DIN S/N = 46 dB)
30 Hz — 15 kHz
Maximum Supply Current
MP3 Decode
DC 5 V
1.5 A
Quieting Sensitivity
Compliant with MPEG-1/2 Audio Layer-3
Compliant with Windows Media Audio
AAC-LC “.aac”, “.m4a” files
Frequency Response
( 3 dB)
WMA Decode
AAC Decode
Signal-to-Noise Ratio
Stereo Separation (1 kHz)
AM Frequency Range
64 dB (MONO)
WAV Decode
Linear-PCM
40 dB
FLAC Decode
FLAC file (Up to 96 kHz/24 bit)
530 kHz — 1 700 kHz (10 kHz space)
29 dBμ (28.2 μV)
Usable Sensitivity
(S/N = 20 dB)
43
ENGLISH
SPECIFICATIONS
Version
Bluetooth 3.0
Preout Level/Load (CD)
Preout Impedance
/
/
: 5 000 mV/10 kΩ
Frequency Range
Output Power
2.402 GHz — 2.480 GHz
: 4 000 mV/10 kΩ
: 2 500 mV/10 kΩ
+4 dBm (MAX), 0 dBm (AVE) Power Class 2
Maximum Communication Range Line of sight approx. 10 m (32.8 ft)
≤ 600 Ω
Profile
HFP 1.6 (Hands-Free Profile)
Operating Voltage
14.4 V (10.5 V — 16 V allowable)
A2DP (Advanced Audio Distribution Profile)
AVRCP 1.5 (Audio/Video Remote Control Profile)
SPP (Serial Port Profile)
Maximum Current Consumption
Operational Temperature Range
Installation Size (W × H × D)
10 A
–10°C — +60°C
PBAP (Phonebook Access Profile)
182 mm × 53 mm × 158 mm
(7-3/16” × 2-1/16” × 6-1/4”)
Frequency Response ( 3 dB)
Input Maximum Voltage
Input Impedance
20 Hz — 20 kHz
1 000 mV
Net Weight (includes Trimplate,
Mounting Sleeve)
/
: 1.4 kg (3.0 lbs)
: 1.4 kg (3.1 lbs)
: 1.4 kg (2.9 lbs)
: 1.3 kg (2.9 lbs)
30 kΩ
Maximum Output Power
Full Bandwidth Power
Speaker Impedance
Tone Action
50 W × 4
22 W × 4 (at less than 1 % THD)
4 Ω — 8 Ω
Subject to change without notice.
Band 1:
Band 2:
Band 3:
Band 4:
Band 5:
Band 6:
Band 7:
Band 8:
Band 9:
Band 10:
Band 11:
Band 12:
Band 13:
62.5 Hz 9 dB
100 Hz 9 dB
160 Hz 9 dB
250 Hz 9 dB
400 Hz 9 dB
630 Hz 9 dB
1 kHz 9 dB
1.6 kHz 9 dB
2.5 kHz 9 dB
4 kHz 9 dB
6.3 kHz 9 dB
10 kHz 9 dB
16 kHz 9 dB
44
ENGLISH
SPECIFICATIONS
•
•
Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
HD Radio Technology manufactured under license from iBiquity Digital Corporation. U.S.
HD Radio, and “ARC” logos are registered trademarks or trademarks of iBiquity Digital
Corporation in the United States and/or other countries.
“Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been
designed to connect specifically to iPod, or iPhone, respectively, and has been certified
by the developer to meet Apple performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and regulatory standards. Please
note that the use of this accessory with iPod or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
libFLAC
Copyright (C) 2000-2009 Josh Coalson
Copyright (C) 2011-2013 Xiph.Org Foundation
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
-
Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
•
-
Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
-
Neither the name of the Xiph.org Foundation nor the names of its contributors may be
used to endorse or promote products derived from this software without specific prior
written permission.
•
•
•
Lightning is a trademark of Apple Inc.
Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered
trademarks of Pandora Media, Inc., used with permission.
iHeartRadio® and iHeartAuto™ are trademarks owned by iHeartMedia, Inc. All uses are
authorized under license.
SPOTIFY and the Spotify logo are among the registered trademarks of Spotify AB.
Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights
reserved.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS
IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
•
•
•
•
•
•
The “AAC” logo is a trademark of Dolby Laboratories.
Google, Google Play and Android are trademarks of Google Inc.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other
trademarks and trade names are those of their respective owners.
The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States
and in other countries.
Qualcomm aptX is a product of Qualcomm Technologies International, Ltd. Qualcomm is a
trademark of Qualcomm Incorporated, registered in the United States and other countries,
used with permission. aptX is a trademark of Qualcomm Technologies International, Ltd.,
registered in the United States and other countries, used with permission.
•
•
45
ENGLISH
|